The improvement of the methane combustion activity was observed in cyclic temperature-programmed and isothermal reactions over Pd/ZrO2 catalysts by simple reduction/re-oxidation treatment. The catalytic activity increased during the initial stages of isothermal reaction, and the light-off temperature was lowered as the number of cycles increased in the cyclic temperature-programmed reaction. To reveal the origin of activation, variations in the reduction properties after the activation period were carefully investigated through CH4 temperature-programmed reduction (TPR) measurements. From the CH4-TPR results, it was confirmed that the reduction temperature decreased significantly after activation. The observation of the CH4-TPR peak at relatively low temperatures is directly proportional to the catalytic activity of CH4 combustion. It was therefore concluded that repeated reduction/re-oxidation occurred in the reactant stream, and this phenomenon allowed the combustion reaction to proceed more easily at lower temperatures.

The direct Cr (VI) reduction process by oxalic acid was conducted and the results showed that the Cr (VI) was efficiently reduced by oxalic acid at high reaction temperature and high dosage of oxalic acid. The reduced product, Cr (III), was easily generated stable complex compounds (Cr(HC2O4)3) with oxalate, which displayed a negative effect on the reduction process. The high reaction temperature and high acidic medium could destroy the stable structure of a complex compound to release oxalate, and facilitate the reduction of Cr (VI). Generally, the present study provided a versatile strategy for Cr (VI) reduction, exhibiting a bright application future for real wastewater treatment.

In this paper, we first report that WO_x contained nanoalloys exhibit stable electrocatalytic performance in alkaline media, though bulk WO₃ are easy to be dissolved in NaOH solutions. Carbon supported oxide-rich Pd-W alloy nanoparticles (PdW/C) with different Pd:W atom ratios were prepared by reduction-oxidation method. Among the catalysts, the oxide-rich Pd0.8W0.2/C (Pd/W = 8:2, atom ratio) exhibits the highest catalytic activity for oxygen reduction reaction. The X-ray photoelectron spectroscopy data shows that ~40% of Pd atoms and ~60% of the W atoms are in their oxides form. The Pd 3d_5/2 peaks in oxide-rich Pd-W nanoalloys are positive shift compared with that of Pd/C, which indicates the electronic structure of Pd is affected by the strong interaction between Pd and W/WO₃. Compare to Pd/C, the onset potential of oxygen reduction reaction at the oxide-rich Pd_0.8W_0.2/C is positive shifted. The current density (mA·mg Pd⁻¹) at the oxide-rich Pd_0.8W_0.2/C is ~1.6 times of that at Pd/C. The oxide-rich Pd_0.8W_0.2/C also exhibits higher catalytic stability than Pd/C, which demonstrate that it is a prospective candidate for the cathode of fuel cells operated with alkaline electrolyte.

The data from social networks like Twitter is a valuable source for research but full of redundancy, making it hard to provide large-scale, self-contained, and small datasets. The data recording is a common problem in social media-based studies and could be standardized. Sadly, this is hardly done. This paper reports on lessons learned from a long-term evaluation study recording the complete public sample of the German and English Twitter stream. It presents a recording solution proposal that merely chunks a linear stream of events to reduce redundancy. If events are observed multiple times within the time-span of a chunk, only the latest observation is written to the chunk. A 10 Gigabyte Twitter raw dataset covering 1,2 Million Tweets of 120.000 users recorded between June and September 2017 was used to analyze expectable compression rates. It turned out that resulting datasets need only between 10\% and 20\% of the original data size without losing any event, metadata or the relationships between single events. This kind of redundancy reduction recording makes it possible to curate large-scale (even nation-wide), self-contained, and small datasets of social networks for research in a standardized and reproducible manner.

Human perception of nature and God have always been inextricably linked. In order to understand nature and its inherent processes, including various natural hazards, the reasons for their origin were often attributed to God's will, suffering for sin and the similar. Fear of material and human losses prompted a man to pray and offer sacrifices/gifts and other rituals to appease the "wrath of the gods". The progress of civilization and technology has not alleviated the destruction and trauma that natural disasters inflict on all aspects of social life. A major obstacle to this is the exponential population growth in vulnerable areas. The frequency of natural disasters and the fatalistic attitudes that limit the effective fight against them have motivated religious communities and individuals to cooperate with international and international organizations and institutions to reduce the risk of local disasters. Believers thus receive the necessary psychological and financial assistance and support from religious communities during all phases of disaster management. Therefore, the subject of this paper is a comprehensive examination relationship between the degree of religiosity of the population and how this connection impacts the policy of reducing disaster risk. The aim of the research is to scientifically describe the nature of the relationship between the degree of religiosity of citizens and different segments of disaster risk reduction.

The validity of our universe as a three-dimensional space (3+1 in relativity) is considered a fundamental fact in physics. In this study, we show that our observed world is thus the output of a prior fundamental operator referred to as an organizer. The organizer is an expansion of projecting operators. It is been shown that identical weighted projecting operators, which are associated with identical particles, generate subspaces of entangled states, whereas groups of unequal weighted coefficients are responsible for finite-size subspaces that are associated with unidentical particles. Considering 3D-subspaces as evidence of the coefficients’ arrangement in our universe, we implement our formalism to describe the implacable vectors, location, momentum, and force within each 3D subspace. By implementing the Heisenberg relation, we drive both the classical and quantum expressions for the laws of motion.

Quantum mechanics introduces the concept of an observer who selects a measuring device and reads the outputs. This measurement process is irreversible. Lately, scholars on quantum collapse phenomena have presented a quantum-like formalism describing the measurement results as an interpretation of the measured object. Note that an observer must read the interpretation results after the interpretation process. Therefore, we propose that the definition of the concept of life should be expanded based on the following concept: A living system decreases entropy, measured results are interpreted, and an internal observer reads the commentary.

This work discussed the advantages of reducing copper in molten copper slag with low S content. FactSage calculated the distribution of copper at equilibrium under different sulfur content. The effect of sulfur content on copper recovery under different oxygen partial pressures was pointed out. The effect of sulfur content on copper recovery in the actual reduction process was explored through experimental research. Under the condition of low sulfur, the Recovery of copper and the stability of the experiment have an ideal results.

The current paper is devoted to the introduction of simpler Eulerian variational principles from which all the relevant equations of non-barotropic stationary magnetohydrodynamics can be derived for magnetic fields which lie on surfaces. A variational principle is given in terms of three independent variables for stationary non-barotropic magnetohydrodynamic flows. This is a smaller number of variables than the eight variables which appear in the standard equations of non-barotropic magnetohydrodynamics which are the magnetic field, the velocity field, the specific entropy and the density. We further investigate the case in which the flow along magnetic lines is not ideal.

A highly efficient reduction process of Cr (VI) with biochar was conducted in this paper. The results showed that nearly 100% Cr (VI) was reduced at selected reaction conditions: the dosage of biochar at m (C)/m(Cr) = 3.0, reaction temperature of 90 ℃, reaction time at 60 min and concentration of H2SO4 of 20 g/L, respectively. The reduction kinetics analysis demonstrated that the reduction of Cr (VI) fitted well with the pseudo-first-order model and the apparent activation energy was calculated to 40.24 kJ/mol. Response surface methodology confirmed that all the experimental parameters had positive effect on the reduction of Cr (VI). The influence of each parameter on the reduction process followed the order: dosage of biochar> Concentration of H2SO4 > Reaction Temperature > Reaction Time. This paper provided a versatile strategy for treatment of wastewater containing Cr (VI) and showed a bright tomorrow for wastewater treatment.

Microbe laden air particles, known as bio-aerosols, are routinely generated, in clinical dentistry due to the operative instrumentation within a milieu rich in salivary organisms. As the major mode of transmission of SARS-CoV-2 appears to be airborne aerosols and droplets, there has been an intense focus on such aerosol generating procedures (AGP). As there has been no systematic reviews on the efficacy of bio-aerosol reducing measure in dentistry, the objective of this systematic review was to evaluate the literature on three major AGPs, rubber dam application, pre-procedural oral rinse, and high-volume evacuation (HVE) aimed at reducing dental bio-aerosols. Method: PubMed via Ovid MEDLINE, EBSCO host, Cochrane Library, and Web of Science databases between January 01, 1985, and April 30, 2020, were searched.Results: A total of 156 records in the English language literature were identified, of which 17 clinical studies with 724 patients were included in the final analyses. The eligible reviewed articles revealed the inadequacy of the afore mentioned three principal AGPs used in contemporary dental practice to minimise bio-aerosols. HVE appears to be the most efficacious method, although no single approach provides total elimination of bio-aerosols. Conclusion:This, the first systematic review on methods of controlling bio-aerosols in dental operatory settings, indicates that employing combination strategies of rubber dam, with a pre-procedural antimicrobial oral rinse, and HVE can significantly minimize bio-aerosols. As the quality of the currently available data on dental bio-aerosols are rather poor, further, controlled, multi-centre studies are essential to address this critical issue.

Numerical weather prediction is an initial-value problem, for determination of the initial conditions, there are many methods and one of the most classical methods is variational methods in three dimensions, or 3D-Var. In this approach, with a defined cost function proportional to the square of the distance between the analysis and both the background and the observations, one can obtain the analysis. In the cost function, the background and the observations are reshaped to vectors; within this step, the order of the background error covariance matrix and the observational error covariance matrix becomes huge, which is not convenient to one to obtain the analysis. In this paper, according to the matrix analysis approach, we put forward some possible improvements to the dimension-reduction algorithm of 3D-Var, so that provide some references for data assimilation.

Replacing carbon by hydrogen is a huge step towards reducing CO₂ emissions in the iron- and steel-making industry. The reduction of iron oxides using hydrogen plasma smelting reduction as an alternative to conventional steel-making routes has been studied at Montanuniversitaet Leoben, Austria. The aim of this work was to study the slag formation during the reduction process and the reduction behaviour of iron oxides. Furthermore, the reduction behaviour of iron ore during continuous feeding was assessed. Mixtures of iron ore and calcined lime with a basicity of 0, 0.8, 1.6, 2.3, and 2.9 were melted and reduced by hydrogen. The off-gas composition was measured during the operations to calculate the process parameters. The reduction parameters, namely the degree of reduction, degree of hydrogen utilisation, produced iron, and slag, are presented. The results of the batch-charged experiments showed that at the beginning of the reduction process, the degree of hydrogen utilisation was high, and then, it decreased over the operation time. In contrast, during the continuous-feeding experiment, the degree of hydrogen utilisation could be kept approximately constant. The highest degrees of reduction and hydrogen utilisation were obtained upon the application of a slag with a basicity of 2.3. The experiment showed that upon the continuous feeding of iron ore, the best conditions for the reduction process using hydrogen could be applied.

The development of hydrogen plasma smelting reduction as a CO₂ emission-free steel-making process is a promising approach. This study presents a concept of the reduction of hematite using hydrogen thermal plasma. A laboratory scale and pilot scale hydrogen plasma smelting reduction (HPSR) process are introduced. To assess the reduction behavior of hematite, a series of experiments has been conducted and the main parameters of the reduction behavior, namely the degree of hydrogen utilization, degree of reduction and the reduction rate are discussed. The thermodynamic aspect of the hematite reduction is considered and the pertinent calculations have been carried out using FactSage^TM 7.2. The degree of hydrogen utilization and the degree of reduction were calculated using the off-gas chemical composition. The contribution of carbon, introduced from the graphite electrode, ignition pin and steel crucible, to the reduction reactions was studied. The degree of reduction of hematite, regarding H₂O, CO and CO₂ as the gaseous reduction products, is determined. It is shown that the degree of hydrogen utilization and the reduction rate were high at the beginning of the experiments, then decreased during the reduction process owing to the diminishing of iron oxide. Conducting experiments with the high basicity of slag B₂=2 led to a decrease of the phosphorus concentration in the produced iron.

Given a polynomial $P(x_{1}, x_{2}, \ldots, x_{n})$ which is the sum of terms, where each term is a product of two distinct variables, then the problem $APSS$ consists in calculating the total sum value of $\sum_{\forall U_{i}} P(u_{1}, u_{2}, \ldots, u_{n})$, for all the possible assignments $U_{i} = \{u_{1}, u_{2}, ... u_{n}\}$ to the variables such that $u_{j} \in \{0, 1\}$. $APSS$ is the abbreviation for the problem name Algebraic Polynomial Sum Solver Over $\{0, 1\}$. We show that $APSS$ is in $\#L$ and therefore, it is in $FP$ as well. The functional polynomial time solution was implemented with Scala in \url{https://github.com/frankvegadelgado/sat} using the DIMACS format for the formulas in $\textit{MONOTONE-2SAT}$.

Abstract: The paper defines the characteristics of two proto-quark stars (M_b=1.22M_? and M_b=1.62M_(?"\ " )) that were formed after the explosion of the supernova. It is assumed that the changes in the energy and lepton charge of the central regions of the pre-supernova star can be neglected during the implosion. The equation of state for hot quark matter is determined based on the MIT bag theory taking into account the presence of neutrinos. The possible maximum values of the central temperatures of these stars are determined. The energy of neutrinos in the studied proto-quark stars is of the order of 250-300 MeV. The decrease in the mass of these stars during cooling is about 0.16 for M_b=1.22M_? and 0.25 for M_b=1.62M_(?"\ " ).

Background: Twitter is a major tool for communication in emergencies such as natural disasters. This online social network allows the user to produce content, and it is not designed exclusively for news releases, as opposed to other service providers. Aim: The aim of this study is to investigate Twitter uses in natural disasters and pandemics. Methods: The included studies reported the role of Twitter in natural disasters. The studies that report in settings other than the natural disasters (such as man-made disasters) and other social media were excluded. Electronic databases for a comprehensive literature search including MEDLINE, Web of Science, CINAHL, PsycINFO, Cochrane Register of Controlled Trials (CENTRAL) and EMBASE were used to identify the records that match the mentioned inclusion criteria published till May 2020. The study characteristics were extracted from the qualified studies including year of publication, findings, and geographical location of the study conduct. A narrative synthesis for this literature review was used. Results: The search identified 822 articles of which 780 articles were removed, 256 were not available, 311 papers were not relevant, 16 were duplicated articles, and 197 were non-related to the emergencies. 45 articles met the selection criteria and were included in the review. eleven themes were found in the narrative synthesis including early warning, disseminating information and misinformation, advocacy, personal gains, assessment, various roles of organizations, public mood, geographical analysis, charity, using influencers, and trust. Conclusions: It is recommended that influential individuals be identified in each country and community before disasters occur so that the necessary information can be disseminated in response to disasters. Preventing the spread of misinformation is one of the most important issues in times of disaster, especially pandemics. Disseminating accurate, transparent, and prompt information from relief organizations and governments can help. Also, analyzing Twitter data can be a good source for understanding the mental state of the community, estimating the number of injured people, estimating the points affected by natural disasters, and modeling the prevalence of epidemics. Therefore, various groups such as politicians, the government, non-governmental organizations, aid workers, and the health system can use this information to plan and implement interventions.

With an increasing demand for quality of care and lower costs, hospitals are looking for industry-based methods to improve efficiency in their processes. This study aims to reduce waste in a public hospital in Mexico by improving the medical supply process for the operating room. To this end, a lean healthcare (LH) implementation following the DMAIC approach (Define-Measure-Analyze-Improve-Control) is carried out. We analyze the value stream of the supply process, including main surgical procedures and their related medical supplies, and identify different causes of inefficiency, which are evaluated and controlled through different tools, including a value stream map, Kanban, and the 5S program. As a result, five types of waste were reduced. Over-processing requests were reduced by 15.3%, defective identification numbers were reduced by 46.5%, redundant processing was improved by 94.8%, near 2.8% of the unnecessary inventory was reduced, and transportation waste was reduced by up to 16.7%. Finally, the lead-time for the main supplies was reduced by 33 days. This work demonstrates that LH and DMAIC are effective in reducing waste and are highly conducive to improving sustainability in healthcare processes. Moreover, it provides practical insights for practitioners regarding the implementation of LH in public hospitals in developing countries.

Changes in the amount and the distribution of mean and turbulent quantities in the free shear layer wake of a 2D NACA 0012 airfoil and AR 4 NACA 0012 wing with passive segmented rigid trailing edge (TE) extensions was investigated at the University of Dayton Low Speed Wind Tunnel (UD-LSWT). The TE extensions were intentionally placed at zero degrees with respect to the chord line to study the effects of segmented extensions without changing the effective angle of attack. Force based experiments was used to determine the total lift coefficient variation of hte wing with seven segmented trailing edge extensions distributed across the span. The segmented trailing edge extensions had negligible effect of lift coefficient but showed measurable decrement in sectional and total drag coefficient. Investigation of turbulent quantities (obtained through Particle Image Velocimetry (PIV)) such as Reynolds stress, streamwise and transverse RMS in the wake, reveal a significant decrease in magnitude when compared to the baseline. The decrease in the magnitude of turbulent parameters was supported by the changes in coherent structures obtained through two-point correlations. Apart from the reduction in drag, the lower turbulent wake generated by the extensions has implications in reducing structural vibrations and acoustic tones.

In this work the influence of the structure forming agent on the composition, morphology and oxygen reduction reaction (ORR) activity of Fe-N-C catalysts was investigated. As structure forming agent (SFA), dicyandiamide (DCDA) (nitrogen source) or oxalic acid (oxygen source) or mixtures thereof were used. For characterization, cyclic voltammetry and rotating disc electrode (RDE) experiments were performed in 0.1 M H2SO4. In addition to this, N2 sorption measurements and Raman spectroscopy were performed for the structural characterization. The role of metal, nitrogen and carbon sources within the synthesis of Fe-N-C catalysts has been pointed out before. Here, we show that the optimum in terms of ORR activity is achieved if both N- and O-containing SFAs are used in almost similar fractions. All catalysts display a redox couple, whereat its position depends on the fractions of SFAs. The SFA has also a strong impact on the morphology: Catalysts that were prepared with a larger fraction of N-containing SFA revealed a higher order in graphitization, indicated by bands in the 2nd order range of the Raman spectra. Nevertheless, the optimum in terms of ORR activity is obtained for the catalyst with highest D/G band ratio. Therefore, the results indicate that the presence of an additional oxygen-containing SFA is beneficial within the preparation.

Jakarta belongs to the cities with the highest flood risk in the world. Its flood hazard is driven by land subsidence, soil sealing, changes in river discharge and increasingly sea level rise. As all of these trends are set to continue, Jakarta’s flood hazard is expected to intensify in the future. Designing and implementing risk reduction and adaption measures is therefore of utmost importance. Against the background, the paper draws on a discourse analysis and original empirical household survey data to review and evaluate current adaptation measures and to analyze in how far they describe a path that is transformative from previous risk reduction approaches. The results show that the focus is clearly on engineering solutions, foremost in the Giant Sea Wall project. The project is likely to transform the city’s flood hydrology. However, it cements rather than transforms the current risk management paradigm which gravitates around the goal of controlling flood symptoms, rather than addressing their anthropogenic root causes. The results also show that the planned measures are heavily contested due to concerns about ecological impacts, social costs, distributional justice, public participation and long-term effectiveness. On the outlook, the results therefore suggest that the more the flood hazard will intensify in the future, the deeper a societal debate will be needed about the desired pathway in flood risk reduction and overall development planning – particularly with regards to the accepted level of transformation, such as partial retreat from the most flood-affected areas.

Nickel molybdate, NiMoO₄, nanoparticles were synthesized via calcination of an oxalate complex in static air at 500 °C. The oxalate complex was analyzed by thermal gravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR). The as-synthesized nickel molybdate was characterized by Brunauer–Emmett–Teller technique (BET), X-ray diffraction (XRD), and transmission electron microscopy (TEM) and its catalytic efficiency was tested in the reduction reaction of the three-nitrophenol isomers. The nickel molybdate displays a very high activity in the catalytic reduction of the nitro functional group to an amino. The reduction progress was controlled using UV-Vis absorption.

This study aimed to investigate the effect of reducing the amount of organic waste on the weight of cats in Tehran. The weight of 4192 cats was measured from spring 2016 to the end of winter 2020. They were classified into 6 age groups, 2 gender groups, and 13 geographical areas. Their weight was measured for 48 months (16 seasons). The statistical parameters analysis showed no weight loss in 2017, but since 2018, cats have been losing weight every year. They had lost about 178g of their weight in 2018. The sharpest annual decrease was observed in 2019 when about 301g of weight loss was recorded. In the winter of 2020, 115g of weight loss took place. In the spring of 2017, no weight change was observed, but in the spring of 2018, the cats lost 155g of their weight. Their weight loss intensified in the spring of 2019 and about 299g of weight loss was observed. In the summer of 2017, as in the spring of the same year, no weight loss was recorded, but for the summer of 2018, the weight loss was evident and about 205g of the weight of the cats had been reduced. The weight loss in the summer of 2019 not only continued but intensified and about 304g of weight loss was recorded for cats. Weight change was not observed in the fall of 2017 as in the spring and summer of the same year. In the fall of 2018, weight loss was recorded for cats. They had lost about 324g of their weight in the fall of 2018. Also, they experienced a weight loss of about 218g in the fall of 2019. During the spring, summer, and autumn of 2017, no weight loss was observed in the cats for the winter of 2018, but in the winter of 2019, the cats faced the most severe weight loss (seasonally). They lost about 401g of weight in the winter of 2019. Of course, in the winter of 2020, about 186g of weight loss was observed in cats. The results showed that female cats did not lose weight in 2017 but experienced weight loss in 2018 with a weight loss of 181g. The weight loss of females intensified in 2019 and 294g of weight loss was recorded. Female cats lost 186g of their weight in the winter of 2020. Male cats did not lose weight like female cats in 2017. But in 2018, a weight loss of 166g was observed in male cats. The weight loss of male cats continued in 2019 and 311g of weight loss was recorded for them. However, in 2020, unlike females, weight loss was not observed in male cats. It can be said that both sexes lost more weight in the winter of 2019 than in other seasons. In 2017, weight loss was observed only for the region of 10, and in the same year, weight gain was recorded for the region of 15. But in 2018, except for regions 3, 4, 15, and 19, weight loss was observed in other regions. In 2019, the weight loss of cats spread and weight loss was observed in all regions except the region of 12. In winter 2020, weight loss was recorded only in the region of 4. In the end, it can be concluded that the weight of cats has decreased since the spring of 2018 because the beginning of the decrease in the amount of organic waste has been recorded since the winter of 2018. So, there is a direct relationship between the weight of cats and the amount of organic waste (access to food). The amount of garbage has been decreasing since the winter of 2018, and the average weight of cats has also been decreasing since the spring of 2018 due to the decrease in access to food.

This study investigated the development of Aedes aegypti density in houses of the urban locality of Poblado Miguel Alemán Valdes, in the Sonora state of Mexico, after application of 1% propoxur paint as full wall coverage (IP) and targeted indoor painting (IP 1m) in comparison to IRS with propoxur 70% WP (full wall coverage). The 1% propoxur paint was applied by the homeowners by brushing and rolling at the recommended dose of 1L/8 m², equivalent to 1.5 g a.i./m², while IRS was conducted by professionals with Propoxur 70% WP at a dose of 1 g a.i./m². Adult mosquito surveys were conducted in a random sample of houses in each block one week before the interventions and at week 1, month 1 to 4, month 6, month 9 and month 12 post-interventions. All three propoxur based treatments provided similar reductions (43.7%, 44.9% and 41.3% for IP, IP 1m and IRS respectively) in the fraction of houses positive in female Aedes aegypti resting indoor and outdoor as one year average of 8 follow up surveys. Indoor resting density of Aedes females during the one-year evaluation was reduced by 77.5% through IP followed by IP 1m with 64.2% reduction and 30% reduction with IRS. Culex mosquitoes’ interior density was affected as well by the insecticide treatments with similar average reductions for IP 1m (50.0%) and IRS (57.8%) in comparison with control. Aedes breeding was impacted by the insecticide paint in similar extent for both interventions, expressed by a substantial reduction of the House Index (20.1% IP, 31.2% IP 1m) and especially the Container Index (51.8% IP, 61.7% IP 1m) during the one-year surveys in comparison to control. In contrast, IRS treated block experienced an increase in both indexes. However, despite IP and IP 1m impacted in Aedes adult and immature indexes with noticeable reductions, the differences in all cases were not significative among the different insecticide treatments. The low sample size and mosquito population levels may have influenced the statistical outcomes. More than 80% of the interviewed residents were satisfied with the effectiveness of the paint and IRS treatments. The determination of the blood cholinesterase activity of tested individuals after the use of the carbamate paint and IRS in this study did not exceed acceptable inhibition limits. This study suggests that the application of propoxur paint by homeowners as full house coverage or as targeted indoor painting can be a safe and accepted intervention method for density reduction of Aedes aegypti populations in urban environments.

(1) Background: We reviewed the logistics of the implementation of pathogen inactivation (PI) using the INTERCEPT Blood System™ for platelets and the experience with routine use and clinical outcomes in the patient population at the Sírio-Libanês Hospital of São Paulo, Brazil. (2) Methods: Platelet concentrate (PC), including pathogen reduced (PR-PC) production, inventory management, discard rates, blood utilization, and clinical outcomes were analyzed over the 40 months before and after PI implementation. Age distribution and wastage rates were compared over the 10 months before and after approval for PR-PC to be stored for up to 7 days. (3) Results: A 100% PR-PC inventory was achieved by increasing double apheresis collections and production of double doses using pools of two single apheresis units. Discard rates decreased from 6% to 3% after PI implementation and further decreased to 1.2% after 7-day storage extension for PR-PCs. The blood utilization remained stable, with no increase in component utilization. A significant decrease in adverse transfusion events was observed after the PI implementation. (4) Conclusion: Our experience demonstrates the feasibility for Brazilian blood centers to achieve a 100% PR-PC inventory. All patients at our hospital received PR-PC and showed no increase in blood component utilization and decreased rates of adverse transfusion reactions.

This paper aims to delve into how gender dimensions observed before, during and after a disaster, have been addressed in two internationally recognised frameworks developed for reducing risks of disasters: Hyogo Framework Action (2005-2015) and Sendai Framework for Disaster Risk Reduction (2015-2030). Building on a systematic review, we evaluate 33 scholarly peer-reviewed journal articles, including book chapters and websites in areas of gender, disaster risk reduction and vulnerability. This study documents a comparative picture of these two frameworks and shows the practical implications of the Sendai Framework for Disaster Risk Reduction (SFDRR) by addressing women’s empowerment in the light of their active participation in disaster risk reduction process. The findings of the study suggest that the frameworks have discussed the reduction of women’s socioeconomic vulnerabilities, as well as encouraged their empowerment. Comparing the two frameworks, it appears in the current study that there has been a significant gap in the existing literature that does not explicitly document comparing and contrasting features of a gender lens in the policy documents.

Macadamia (Macadamia integrifolia) nuts have become an essential commodity crop in Malawi. The nuts are a lucrative commodity and are used for household consumption and income generation among farming families and as a foreign exchange earning crop at country-level. In addition, macadamia production has increased significantly in recent years in the country. Currently, Malawi is the seventh top producer of macadamia nuts, with a global market share of three percent (1,846 metric tonnes on kernel basis). In 2018, exports of macadamia kernel had a value of US$24.3 million (£19.8 million or MKW 18.01 billion). However, the bulk (85%) of the crop is grown on large commercial plantations, but the smallholder sector is emerging as vital for the future growth of the macadamia sub-sector in Malawi. Furthermore, Malawian smallholders consider macadamia production to be a low-input crop with large returns per unit area (US$14.37 kg^-1ha^-1 or MKW 10,701kg^-1ha^-1) thus a lucrative crop with high potential for poverty reduction and wealth creation among these farming families. This paper, therefore, explores: (i) the historical and current trends in macadamia nut production in Malawi; (ii) analyses the country’s macadamia value chain and (iii) discusses the constraints of macadamia production in Malawi for informed policymaking. Thus, the synthesis of the Malawian macadamia sub-sector provides an understanding of the vital contributions of macadamias to Malawi’s economic growth and improvement of livelihoods.

A new generation of universal tools and languages for modeling and simulation multi-physical domain applications emerged and became widely accepted, which generate large-scale systems of differential algebraic equations (DAEs) automatically. Motivated by the characteristics of DAEs systems with large dimension, high index or block structures, we first propose a modified Pantelides’ algorithm (MPA) for any high order DAEs based on its Σ matrix, which is similar to Pryce’s Σ method. By introducing a vital parameter vector, a modified Pantelides’ algorithm with parameter has been presented.It leads to a block Pantelides’ algorithm (BPA) naturally which can immediately compute the crucial canonical offsets for whole (coupled) systems with block-triangular form. We illustrate these algorithms by some examples. And numerical experiments show that the time complexity of BPA can be reduced by at least O(ℓ) compared to the MPA, which is mainly consistent with the results of our analysis.

In addition to being a source of freshener, coffee has an enormous possibility to be developed as a source of antioxidants for functional beverages. However, efforts to increase the value added of coffee as a health functional drink are still hindered by the presence of high level of caffeine, which is thought to have adverse effects on health, especially for coffee lovers who are vulnerable to caffeine. This study aims to optimise the steaming duration to produce low caffeine coffee while maintaining the sensory attributes and antioxidant compounds contained in it. Indonesian Arabica (Leksana variety) green coffee beans were steamed with multi-level steaming durations (0, 20, 40, 60 and 80 min) followed by roasting (medium-dark roast degree), grinding, and brewing (espresso method). The results indicate that caffeine content in the coffee was inversely proportional to the steaming duration. The lowest caffeine content was obtained from the treatment of 80 min steaming with a decrease of caffeine level up to 28.73%. However, the longer process of steaming caused a significant decrease in polyphenol content and antioxidant activity. The hedonic test shows that the steaming treatment of coffee can increase preferences of panellists. There were two driving attributes that influence the overall liking of coffee, namely: bitterness and aftertaste. Coffee obtained from the treatment of 60 min steaming was most preferred by panellists. The results of APLSR biplot mapping show that there was a big change in almost all attributes in the coffee samples after 40 min steaming.

Biological nitrogen (N) provisioning is a seminal function of the gut microbes in several terrestrial insects, given the unbalanced carbon (C) and N ratios of their diets. Although freshwater insects face comparable dietary N limitations like terrestrial insects, little is known about this function by their gut microbiomes. In this study, we investigated microbial nitrate reduction to ammonium pathways as possible routes of biological N provisioning in two freshwater insects; filter-feeding Hydropsychidae and grazers/collectors Baetidae. After incubation in filtered (microbe-free) artificial stream water (ASW) containing dissolved ¹⁵N-labeled nitrate (treatment) or standard nitrate (control), bulk δ¹⁵N values of treatment samples (Baetidae = 100.62 ± 10.23, mean ± S.E.; Hydropsychidae = 76.82 ± 7.20) were significantly higher than controls (Baetidae = 10.14 ± 0.12 ; Hydropsychidae = 9.03 ± 0.20) in both functional feeding groups (F _{(3, 13)} = 296, P < 0.0001). The treatment δ¹⁵N values are cautiously interpreted as reflecting uptake and incorporation of microbe-derived ¹⁵N-metabolites (¹⁵NH₄ or ¹⁵N-amino acids) into host tissues following nitrate reduction to ammonium pathways in the gut lumen. Microbial nitrate reduction to ammonium activities was assessed via the quantification of dissimilatory (nrfA) and assimilatory (nasA) nitrate reduction to ammonium gene transcripts. There were no significant differences between control and treatment groups within each insect groups. Overall, this study provides a demonstration of the feasibility of applying ¹⁵N-stable isotope analysis for investigating, potential symbiotic functions of freshwater insect gut microbiomes, despite the preliminary nature of the results.

One of the key areas of the International Renewable Energy Agency’s (IRENA) programme of work is the analysis of renewable technology costs and performance and the dissemination of these results to as wide an audience as possible. In addition to analysis, IRENA seeks to engage a broad range of stakeholders in the context of this work through the Renewable Costing Alliance. The Costing Alliance brings together companies, industry association, governments and researchers to share, confidentially, data for real-world renewable energy project cost and performance, helping to build further on IRENA’s costing work to date. In this context the authors analyse the current cost differentials and cost reduction potentials for solar PV in Japan compared to best practice levels and identify the reasons for higher costs in Japan and how to reduce them. This study analyses the current installed cost differentials for utility-scale, commercial and residential rooftop solar PV systems. In addition to identifying the reasons for the cost differentials, potential policy recommendations to reduce the cost differential are identified.

The recently proposed Holography-inspired approach to quantum gravity is reviewed and expanded. The approach is based on the foliation of the background spacetime and reduction of the offshell states to the physical states. Careful attention is paid to the boundary conditions. It is noted that the outstanding problems such as the cosmological constant problem and black hole information can be tackled from the common thread of the quantized gravity. One-loop renormalization of the coupling constants and the beta function analysis are illustrated. Active galactic nuclei and gravitational waves are discussed as the potential applications of the present quantization scheme to astrophysics.

Addition of the bulky redox-active diphosphine 1,8-bis(diphenylphosphino)naphthalene (dppn) to [Fe2(CO)6(-edt)] (1) (edt = 1,2-ethanedithiolate) affords [Fe2(CO)4(2-dppn)(-edt)] (3) as the major product, together with small amounts of a P-C bond cleavage product [Fe2(CO)5{1-PPh2(1-C10H7)}(-edt)] (2). The redox properties of 3 have been examined by cyclic voltammetry and it has been tested as a proton-reduction catalyst. It undergoes a reversible reduction at E1/2 = –2.18 V and exhibits two overlapping reversible oxidations at E1/2 = –0.08 V and E1/2 = 0.04 V. DFT calculations show that while the HOMO is metal-centred (Fe-Fe -bonding), the LUMO is primarily ligand-based but also contains an antibonding Fe-Fe contribution, highlighting the redox-active nature of the diphosphine. It is readily protonated upon addition of strong acids to afford two isomeric hydride complexes and catalyzes the electrochemical reduction of protons at Ep = –2.00 V in the presence of CF3CO2H. The catalytic current indicates that it is one of the most efficient diiron electrocatalysts for the reduction of protons, albeit operating at quite negative potential.

Polymeric drag reducers have been developed over many years due to the great number of practical applications. In all of them, the molecular stability is an essential requirement. Usually, polymers break down under turbulent flows, which causes a decrease in their efficiency as drag reducers. Besides that, some specific applications, in agro and biomedical fields, impose a specific requirement that must be fulfilled, which is the use of non-toxic materials. A suitable stable material that is elected to accomplish this necessity is the mucilage of aloe vera, which is a bio-polymer that can be used as an alternative to the synthetic ones. Here, we investigate the role played by the aging of aloe vera on its capacity to reduce drag. The results obtained by ¹H nuclear magnetic resonance indicate that the compositions of young and mature leaves of aloe vera are different and such a difference plays an important role on their efficiency as drag reducers. Tests were performed to analyse the drag reduction in a rotating apparatus and in a pipeline system and the efficiencies of leaves of different ages were compared to their composition. The main conclusion of these experiments is that the young mucilage samples, which are richer in complex polysaccharides and exhibit lower acid contents, are more efficient drag reducers.

The photoreduction of CO2 is an intriguing process, which allows the synthesis of fuels and chemicals. One of the limitations for CO2 photoreduction in the liquid phase is its low solubility in water. This point has been here addressed by designing a fully innovative concept of pressurized photoreactor, allowing operation up to 20 bar and applied to improve the productivity of this very challenging process. The photoreduction of CO2 in the liquid phase was performed using commercial TiO2 (Evonink P25), TiO2 obtained by flame spray pyrolysis (FSP) and gold doped P25 (0.2 wt% Au-P25) in the presence of Na2SO3 as hole scavenger (HS). The different reaction parameters (catalyst concentration, pH and amount of HS) have been addressed. The products in liquid phase were formic acid and formaldehyde. Moreover, for longer reaction time and with total consumption of HS, gas phase products formed (H2 and CO) after accumulation of significant amount of organic compounds in the liquid phase, due to their consecutive photoreforming. Enhanced CO2 solubility in water was achieved by adding a base (pH= 12-14). In basic environment, CO2 formed carbonates which further reduced to formaldehyde and formic acid and consequently formed CO/CO2+H2 in the gas phase through photoreforming. The deposition of small Au nanoparticles (3-5 nm) (NPs) onto TiO2 was found to quantitatively influence the products distribution and increase the selectivity towards gas phase products.

Gold nanoparticles (AuNPs) are currently under intense investigation for biomedical and biotechnology applications, thanks to their ease in preparation, stability, biocompatibility, multiple surface functionalities and size-dependent optical properties. The most commonly used method for AuNPs synthesis in aqueous solution is the reduction of tetrachloroauric acid (HAuCl₄) with trisodium citrate. We observed variations in the pH and concentration of the gold colloidal suspension synthesized under standard conditions, verifying a reduction in the reaction yield by around 46% from pH 5.3 (2.4 nM) to pH 4.7 (1.29 nM). Citrate-capped AuNPs were characterized by UV-visible spectroscopy, TEM, EDS and zeta-potential measurements, revealing a linear correlation between pH and the concentration of the generated AuNPs. This result can be attributed to the adverse effect of protons both on citrate oxidation and on citrate adsorption onto the gold surface, which is required to form the stabilization layer. Overall, this study provides insight into the effect of the pH over the synthesis performance of the method, which would be of particular interest from the point of view of large-scale manufacturing processes.

The consumer’s acceptability of hamburgers elaborated with the flank of culling cows in which the content of salt or fat had been partially replaced was studied. A mixture of potassium chloride, potassium ferrocyanide and sodium ferrocyanide was used as substitutes for the salt. Oat flakes or a mixture of chia and flax seeds were used as substitutes for the fat. The hamburgers were tasted by 34 consumers. Consumers did not detect significant differences between the control and the rest of the formulations. Neither the gender nor the age of the consumers influenced the sensory appraisal. However, many comments regarding texture failures were recorded. Therefore, the substitution of salt and / or fat in the composition of hamburgers made with the flank of cows is a viable alternative for the commercialization of these pieces of low commercial value as long as the texture of the same is adjusted to resemble it to the control.

A simple, effective and environmental-friendly method was adopted for enhancing the photocatalytic activity of g-C3N4 in the reduction of aqueous Cr(Ⅵ) under visible-light irradiation. The enhancement was achieved via treatment of g-C3N4 in organic solvent with addition of NaOH particles by ultrasonic process for two hours. The results demonstrated that the treated g-C3N4 exhibited much higher photocatalytic activity than pristine g-C3N4 in the reduction of Cr(VI) . Under visible light irradiation for 120 min, the reduced ratios of Cr(VI) with the initial concentration of 50 mg/L in the presence of the treated g-C3N4and pristine g-C3N4 were 100% and 37.1%, respectively. With the addition of fulvic acid, Cr(VI) was efficiently removed at 40 min. Based on the characterization results of the structures and other physiochemical properties of the treated g-C3N4 and pristine g-C3N4 by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and UV Vis diffuse reflectance, the possible reasons responsible for the enhanced photocatalytic activity of the treated g-C3N4 were proposed. The yield and mechanism of different exfoliation methods were compared by semi-quantitative method.

Background. Increasing evidence demonstrate that concentration of protein in infant formula >1.9g/100Kcal with high levels of insulinogenic aminoacids is associated with accelerated weight gain, increased fat mass accumulation and risk of adiposity. Purpose of this study was to conduct a systematic review to determine the metabolic effects in infants feed with infant formula optimized in protein. Methods. Systematic review was conducted according PRISMA Statement. RCTs with one intervention group (infant formula with 1.6-1.9gr of protein/100Kcal) and at least one comparative control group (infant formula with >1.9gr of protein/100Kcal) were included. Standardized mean differences (SMD), through random model were calculated. Results. 15 RCT were included. Optimized protein in infant formula was associated with less gain of BMI at 24 months of follow-up (SMD -0.25, IC95% -0.36 to -0.13, p 0.01) and less fat mass accumulation (SMD -0.68, IC95% -0.98 to -0.37, p 0.01). Optimized protein was also associated to less gain of weight, weight/age Z-score, weight/length Z-score, BUN (mmol/dL) and IGF1 (ng/ml). No effect on length/age Z-score was observed. Conclusions. Robust evidence showed optimized protein (1.6gr/100Kcal to 1.9gr/100Kcal) in infant formula is associated with metabolic benefits in infants with less weight gain, BMI and fat mass accumulation.

We propose a forward-only multi-layer encoding-decoding framework based on the principle of Maximal Coding Rate Reduction (MCR$^2$), an information-theoretic metric that measures a statistical distance between two sets of feature vectors up to the second moment. The encoder directly transforms data vectors themselves via gradient ascent to maximize the MCR$^2$ distance between different classes in the feature space, resulting in class-wise mutually orthogonal subspace representations. The decoder follows a process symmetric to the encoder, and transforms the subspace feature vectors via gradient descent to minimize the MCR$^2$ distance between the reconstructed data and the original data. We show that the encoder transforms data to linear discriminative representations without breaking the higher-order manifolds, and the decoder reconstructs the data with high fidelity.

The electrochemical CO2 reduction reaction can lead to high value-added molecules production while helping decrease anthropogenic CO2 emissions. Copper can reduce CO2 to more than thirty different hydrocarbons and oxygenates, but it lacks the required selectivity. We present a computational investigation of the role of nano-structuring and alloying in Cu-based catalysts on the activity and selectivity of CO2 reduction to one-carbon products: carbon monoxide, formic acid, formaldehyde, methanol, and methane. The adsorption, activation, and conversion of CO2 were computed on monometallic and bimetallic (decorated and core-shell) 55-atom Cu-based clusters. The dopant metals considered were Ag, Cd, Pd, Pt, and Zn, located at different coordination sites. The relative binding strength of the intermediates at different applied potentials were used to identify the optimal catalyst for the selective CO2 conversion to one carbon products. It was discovered that single atom doping with Cd and Zn is optimal for the CO2 to carbon monoxide conversion. The core-shell models with Ag, Pd, and Pt provided higher selectivity for formic acid and formaldehyde. The Cu-Pt and Cu-Pd showed lowest overpotential for methane formation.

Abstract: Urban regeneration decision-making is a complex process, as it involves a wide range of decision-makers, public-private partnerships in finance and implementation, including the inevitable considerable amount of risk on a long-term basis. There are a multitude of stakeholders, the citizens being the key stakeholders. It is necessary to involve the citizens in the planning process. Such involvement allows the communities to express their needs and aspirations, which is useful in the policymaking, delivery of planning programs, and in the monitoring process. In such a context, Factor analysis was the statistical technique used (1) Carry out factor analysis based on the principal component analysis method using the software XLSTAT 2021.4.1.1205 - (2) Construct a factor model of Urban Regeneration. (3) Interpret and label the factor dimensions. The results of the analysis indicated that the first two principal components accounted for 60.04% of the total variance of the original dataset. All variables seemed to be, positively correlated to each other and contributed similarly to principal components PC1 &PC2. The observations were well clustered; except for very few outliers. The limitation of the work was that the perceptions of the citizens were limited to the variables derived by the researcher.

Increasing the quality factor (Q) of an optical resonator device has been a research focus to be utilized in various applications. Higher Q-factor means light is confined in a longer time which will produce a shaper peak and higher transmission. In this paper, we introduce a novel technique to increase further the Q-factor of a one-dimensional photonic crystal (1D PhC) cavity device by using an end loop-mirror (ELM). The technique utilizes and recycles the light transmission from the conventional 1D PhC cavity design. The design has been proved to work by using the 2.5D FDTD simulation with Lumerical FDTD and MODE softwares. By using the ELM technique, the Q- factor of a 1D PhC design has been shown to have increased up to 79.53 % from the initial Q value without the ELM. This novel design technique can be combined with any high Q-factor and very high Q-factor designs to increase more the Q-factor value of a photonic crystal cavity devices or any other suitable optical resonator devices. The experimental result shows that the device is measurable by adding a Y-branch component to the one-port structure and able to get the high-Q result.

As bread is the most consumed food by Tunisian population and the major source of salt, a pilot experience of salt reduction in bread has already begun in Bizerte city. Salt analysis in bread collected from Bizerte city was realized with Volhard titration method. Application of the “salt reduction programme” allowed a gradual decrease of salt content in bread by 35 % during three years without detection by Tunisian consumers. A final salt concentration of 1.1 ± 0.1 g/100 g was then achieved. The establishment of an effective salt reduction strategy with lifestyle education is needed to reduce hypertension that is the first cause of death in Tunisia.

Sparkling wine producing and consumption are in constant increase in the last decade and show no sign of slowing. Prior consumption, origin, grape variety, occasion, price and sensorial perception are factors that typically influence wine consumers’ purchasing and consumption behavior. The presence of volatile compounds in sparkling wines, with direct impact on their organoleptic characteristics, is influenced by several factors, such as the base-wine characteristics, grapes cultivar conditions, the used yeasts, the aging stage or wine-making practices. For this study, five sparkling wines variants from Muscat Ottonel grape variety were obtained. For the experimental samples, the grapes were processed by applying secondary fermentation in bottles. The base-wine was obtained through reverse osmosis and had a predetermined alcoholic concentration (10.5 % vol.). This study aimed to analyze the influence of different commercial yeasts (IOC FIZZ™, IOC DIVINE™, LEVULIA CRISTAL™, IOC 18-2007™) on the volatile composition of experimental sparkling wines. The obtained sparkling wines were characterized by the physical-chemical parameters (according to OIV methods of analysis) and volatile fraction (using gas-chromatography). Data showed an important impact on the concentration of the volatile compounds (p &lt; 0.05), depending on the type of inoculated yeast for the second fermentation and only a minor influence on the physical-chemical parameters was registered.

In mathematics, the Riemann hypothesis is a conjecture that the Riemann zeta function has its zeros only at the negative even integers and complex numbers with real part 1/2. Many consider it to be the most important unsolved problem in pure mathematics. It is one of the seven Millennium Prize Problems selected by the Clay Mathematics Institute to carry a US 1,000,000 prize for the first correct solution. We prove the Riemann hypothesis using the Complexity Theory. Number theory is a branch of pure mathematics devoted primarily to the study of the integers and integer-valued functions. The Goldbach's conjecture is one of the most important and unsolved problems in number theory. Nowadays, it is one of the open problems of Hilbert and Landau. We show the Goldbach's conjecture is true using the Complexity Theory as well. An important complexity class is 1NSPACE(S(n)) for some S(n). These mathematical proofs are based on if some unary language belongs to 1NSPACE(S(log n)), then the binary version of that language belongs to 1NSPACE(S(n)) and vice versa.

We used the Bootstrap ARDL method to test the relationship between the export trades, FDI and CO₂ emissions of the BRICS countries. We found that China's foreign direct investment and the lag one period of CO₂ emissions have a cointegration on exports. South Africa's foreign direct investment and CO₂ emissions have a cointegration relationship with the lag one period of exports, and South Africa's the lag one period of exports and foreign direct investment have a cointegration relationship with the lag one period of CO₂ emissions. But whether it is China or South Africa, these three variables have no causal relationship in the long-term. Among the variables of other BRICS countries, Russia is the only country showed degenerate case #1 in McNown et al. mentioned in their paper. When we examined short-term causality, we found that CO₂ emissions and export trade showed a reverse causal relationship, while FDI and carbon emissions were not so obvious. Export trade has a positive causal relationship with FDI. Those variables are different from different situations and different countries.

In 2015, the new installed capacity of global renewable energy power generation exceeded the newly installed capacity of conventional energy power generation, marking a structural change in the construction of the global power system. With the continuous improvement of wind energy utilization technology, the global wind power industry has developed rapidly in recent years. The world's available wind energy is 20 billion kilowatts and has become one of the most economical green power. In China, wind power has become the third largest source of electricity, with the installed capacity increasing from 3.1% in 2010 to 9.2% in 2017. In 2017, China's new installed capacity was 19,660 MW, accounting for 37.45% of the world's new installed capacity. This paper evaluates and compares the efficiency of wind power industry in the four regions of eastern, central, western and northeastern China through EBM models based on radial and non-radial factors. This paper discusses the contribution of China's wind power industry to CO2 emission reduction from the relationship between installed capacity efficiency and CO2 emission reduction efficiency. The conclusions show that the overall efficiency score and ranking of wind power in 2013-2017 is the best in the eastern region, followed by the northeast region and the western and central regions.

Model-based image reconstruction has brought improvements in terms of contrast and spatial resolution to imaging applications such as magnetic resonance imaging and emission computed tomography. However, their use for pulse-echo techniques like ultrasound imaging is limited by the fact that model-based algorithms assume a finite grid of possible locations of scatterers in a medium -- which does not reflect the continuous nature of real world objects and creates a problem known as off-grid deviation. To cope with this problem, we present a method of dictionary expansion and constrained reconstruction that approximates the continuous manifold of all possible scatterer locations within a region of interest. The expanded dictionary is created using a highly coherent sampling of the region of interest, followed by a rank reduction procedure based on a truncated singular value decomposition. We develop a greedy algorithm, based on the Orthogonal Matching Pursuit (OMP), that uses a correlation-based non-convex constraint set that allows for the division of the region of interest into cells of any size. To evaluate the performance of the method, we present results of 2-dimensional ultrasound image reconstructions with simulated data in a nondestructive testing application. Our method succeeds in the reconstructions of sparse images from noisy measurements, providing higher accuracy than previous approaches based on regular discrete models.

This study is framed on the Information Theory as a constructive criterion to generate probabilistic distributions –through the elaboration of Bayesian Networks- and to reduce the uncertainty in the occurrence and relationship between two key psychological variables associated with the sports’ performance: Self-Determined Motivation and Competitive Anxiety. We analyzed 674 universitary students/athletes who competed in the 2017 Universitary Games (Universiade) in México, from 44 universities, with an average age of 21 years old (SD = 2.07), and with a sportive experience of 8.61 years of average (SD = 5.15). Methods: Regarding the data analysis, first of all a CHAID algorithm was carried out for to know the independence links among variables, and then two Bayesian networks (BN) were elaborated. The validation of the BN revealed AUC values ranging from 0.5 to 0.92. Subsequently, various instantations were carried out with hypothetical values applied to the “bottom” variables. Results showed two probability trees that have Extrinisic Motivation and Amotivation at the top, while the anxiety/activation due to the worry for performance was at the bottom of probabilities. The instantiations carried out support the existence of these probabilistic relationships, demonstrating the little influence on the competition anxiety generated by the intrinsic motivation. In conclusion, the reduction of the uncertainty made up by the restricted BN may aloe to re-introduce Information Theory principles in psychosocial studies, allowing authors to obtain useful probabilities values upon target psychological variables related with sportive performance.

In this study, the efficiencies of flat-plate and U-tube solar collectors were investigated experimentally when an Al₂O₃ nanofluid was used as a working fluid and compared to those of solar collectors using water. The energy saving and CO₂ and SO₂ generated were calculated and compared to those of solar collectors using water. In addition, based on the experimental results, an economic analysis of the use of solar collectors in various countries was performed. As the concentration of the Al₂O₃ nanofluid increased, the performance of the solar collector improved. The highest efficiency for the solar collectors was shown at the concentration of 1.0 vol% with the nanoparticle size of 20 nm. The maximum efficiencies of the flat-plate and U-tube solar collectors using 1.0 vol%-Al₂O₃ nanofluid with 20-nm nanoparticles was 74.9% and 72.4%, respectively, when the heat loss parameter was zero. The efficiencies of the flat-plate and U-tube solar collectors using Al₂O₃ nanofluid were 14.8% and 10.7 higher, respectively, than those using water. When 50 EA flat-plate solar collectors were operated for one year using Al₂O₃ nanofluid, the coal use, generated CO₂, and generated SO₂ were 189.99 kg, 556.69 kg, and 2.03 kg less than those of solar collectors using water, respectively. In addition, the largest electricity cost reduction was in Germany.

One of the most common limits to gas sensor performance is the presence of unwanted interference fringes or etalons arising, for example, from multiple reflections between surfaces in the optical path. Additionally, since the amplitude and the frequency of these interference depend on the distance and alignment of the optical elements, they are affected by temperature changes and mechanical disturbances, giving rise to a drift of the signal. In this work, we present a novel semi-parametric algorithm which allows the extraction of a signal, like the spectroscopic absorption line of a gas molecule, from a background containing arbitrary disturbances, without having to make any assumption on the functional form of these disturbances. The algorithm is applied first to simulated data and then to oxygen absorption measurements in presence of strong fringes.To the best of the authors' knowledge, the algorithm enables an unprecedented accuracy particularly if the fringes have a free spectral range and amplitude comparable to those of the signal to be detected. The described method presents the advantage of being based purely on post processing, and to be of extremely straightforward implementation if the functional form of the Fourier transform of the signal is known. Therefore it has the potential to enable interference-immune absorption spectroscopy. Finally, its relevance goes beyond absorption spectroscopy for gas sensing since it can be applied to any kind of spectroscopic data.

New corrosion inhibitor derived from coumarin-3-amine namely 3-((2-chlorobenzylidene)amino)coumarin was synthesized and characterized by CHN elemental analysis in addition to Fourier transform infrared and nuclear magnetic resonance techniques. The anti-corrosion ability of 3-((2-chlorobenzylidene)amino)coumarin to inhibit the impacts of corrosion has been demonstrated and damage reduction of the mild steel also. 3-((2-chlorobenzylidene)amino)coumarin, has been employed as a good corrosion inhibitor for mild steel in HCL solution. The efficiency of the inhibition was figured according to weight loss method and it was 74.6%.

Wireless Sensor Networks (WSN) are the core of Internet of Things and require cryptographic protection due to the increase number of attacks. Cryptographic methods for WSN should be fast and consume low power as these networks consist of battery-powered devices and constrained microcontrollers. NTRU, the fastest and secure public key cryptosystem, uses high degree polynomials, and is susceptible to the lattice basis reduction attack (LBRA). CPKC, proposed by NTRU authors, works on integers modulo $q$ and is easily attackable by LBRA since it uses small numbers for the sake of the correct decryption. Herein, RCPKC, a random congruential public key cryptosystem working on integers modulo $q$ is proposed, such that the norm of a two-dimensional vector formed by its private key is greater than $\sqrt{q}$. RCPKC works similar to NTRU, and it is a secure version of insecure CPKC. RCPKC specifies a range from which the random numbers shall be selected, and it provides correct decryption for valid users and incorrect decryption for an attacker using LBRA by Gaussian lattice reduction. Because of its resistance to LBRA, RCPKC is more secure. Simultaneously, due to the use of big numbers instead of high degree polynomials, RCPKC is about 24 (7) times faster in encryption (decryption) than NTRU. Also, RCPKC is more three times faster than the most effective known NTRU variant, BQTRU. Compared to NTRU, RCPKC reduces energy consumption at least seven times that allows increasing life-time of unattended WSN more than seven times.

EMG analysis is becoming increasingly important in many research and clinical applications, including muscle fatigue detection, control of robotic mechanisms and prostheses, clinical diagnosis of neuromuscular diseases and quantification of force. However, electromyographic signals can be contaminated by various types of noise, interference and artifacts, which can lead to misinterpretation of the data acquired using this method. Even assuming best practices, the collected signal may still be altered by such contaminants. The aim of this paper is to review methods employed to reduce contamination of single channel EMG signals. This review is limited to methods performed directly on the measured EMG signal and those that allow total reconstruction of the EMG signal. Subtraction methods used in the time domain, denoising methods performed after signal decomposition and hybrid methods are assessed. It is defended that individual methods may be more or less suitable for a particular application depending on contaminant(s) present in the signal and on the specific requirements of the application.

As China put forward its “carbon emissions peak and carbon neutrality” goals, how to achieve carbon reduction had become a key for China’s goal. The manufacturing industry is an important source of carbon dioxide emissions. For a manufacturing country like China, adjustments in various aspects of the industry would have a huge impact on carbon emissions. As an important reform of contemporary production mode, the process of production automation in China will inevitably affect China's carbon emissions. Therefore, the analysis of the impact of production automation on carbon dioxide emissions was an important basis for judging the future carbon reduction in China. Refer to the traditional study of carbon Kuznets curve, this paper analyzed the impact of average wage on production automation and the role of production automation in the carbon Kuznets curve(CKC). This paper proposed that production automation plays a mediating role in the process of carbon emissions, and gives a verification model of the mediating role. By analyzing the relationship between average wage and production automation process, the U-shaped curve relationship between them was verified. By examining the relationship between carbon dioxide emission data and production automation industry in China, we verified that production automation plays a partial mediating role in the change of carbon Kuznets curve. Combined with the analysis of the two parts, this paper believed that with the continuous development of China's intelligent manufacturing industry, China's carbon reduction prospects were more optimistic, and there was a good industrial foundation to achieve the “carbon peaking and carbon neutrality” goals. Finally, this paper proposes policy suggestions as increase research investment in production automation, help promote the application of production automation, encourage the research and application development of low-carbon technology, especially encourage modular design, so as to give full play to the role of production automation in the process of carbon neutrality in China.

Cardiac monitoring based on wearable photoplethysmography (PPG) is widespread because of its usability and low cost. Unfortunately, PPG is negatively affected by various types of disruptions, which could introduce errors to the algorithm that extracts Pulse Rate Variability (PRV). This study aims to identify the nature of such artifacts caused by various types of factors under the conditions of precisely planned experiments. We also propose methods for their reduction based solely on the PPG signal while preserving the frequency content of PRV. The accuracy of PRV derived from PPG was compared to Heart Rate Variability (HRV) derived from the accompanying recorded ECG. The results indicate that filtering PPG signals using the Discrete Wavelet Transform and its inverse (DWT/IDWT) is suitable for removing slow components and high-frequency noise. Moreover, the main benefit of amplitude demodulation is better preparation of the PPG to determine the duration of pulse cycles and reduce the impact of some other artifacts. Postprocessing applied to HRV and PRV indicates that the correction of outliers based on local statistical measures of signals and the AR model is only important when PPG is of low-quality and has no effect under good signal quality. The main conclusion is that DWT/IDWT, followed by amplitude demodulation, enables the proper preparation of the PPG signal for the subsequent use of PRV extraction algorithms. However, postprocessing in the proposed form should be applied more in the situations of observed strong artifacts than in motionless laboratory experiments.

Recently, electrocatalysts for oxygen reduction reactions (ORRs) as well as oxygen evolution reactions (OERs) hinged on electrospun nanofiber composites have attracted wide research attention. Transition metal elements and heteroatomic doping are important methods used to enhance their catalytic performances. Lately, the construction of electrocatalysts based on metal-organic framework (MOF) electrospun nanofibers has become a research hotspot. In this work, bimetallic NixCoy-ZIF nanocrystals were synthesized in an aqueous solution, followed by NixCoy-ZIF/PAN electrospun nanofiber precursors, which were prepared by a simple electrospinning method. Bimetal (Ni-Co) porous carbon nanofiber catalysts doped with nitrogen, oxygen, and sulfur elements were obtained at high-temperature carbonization treatment in different atmospheres (Ar, Air, and H2S), respectively. The morphological properties, structures, and composition were characterized by SEM, TEM, SAED, XRD, and XPS. Also, the specific surface area of materials and their pore size distribution was characterized by BET. Linear sweep voltammetry curves investigated catalyst performances towards oxygen reduction and evolution reactions. Importantly, Ni1Co2-ZIFs/PAN-Ar yielded the best ORR activity, whereas Ni1Co1-ZIFs/PAN-Air exhibited the best OER performance. This work provides significant guidance for the preparation and characterization of multi-doped porous carbon nanofibers carbonized in different atmospheres.

Pulsed thermography is a commonly used non-destructive testing method, and is increasingly studied for advanced materials such as carbon fiber-reinforced polymer (CFRP) evaluation. Different processing approaches are proposed to detect and characterize anomalies that may be generated in structures during the manufacturing cycle or service period. In this study, we used a type of matrix decomposition using Robust-PCA via Inexact-ALM in our experiment. We investigate this method as a pre-and post-processing method on thermal data acquired by pulsed thermography. We employed state-of-the-art methods, i.e., PCT, PPT, and PLST, as the main process. The results indicate that pre-processing on thermal data can elevate the defect detectability while post-processing, in some cases, can deteriorate the results.

People living in areas of significant seismic risk seldom undertake sufficient preparations to safeguard their family. This is most problematic in remote communities such as those along the Dead Sea Fault, Israel, where self-reliance is a key factor in coping with disasters. To facilitate individual and familial involvement in earthquake preparedness in remote areas, we designed a tool for self-assessment of risk and preparedness. The personalized risk assessment is based on national hazard and building standards, and on personal input regarding structure characteristics. The risk and preparedness evaluations enhance awareness and provide immediate feedback to help users improve familial preparedness. Spatial analysis of the data collected is used to form high-resolution maps that expose specific challenges for emergency response. A study conducted in the town of Mitzpe Ramon exposed neighborhoods with relatively high risk of damage and low preparedness. Integrating these results with seasonal stress-factors such as peak tourism and extreme weather, provides new and important insights on the ability of the local community and emergency forces to cope with multi-hazard situations. Analysis of the heterogeneous distribution of expected hardship within a community should be implemented world-wide to improve risk mitigation.

Chemotherapy is a standard therapeutic option for triple-negative breast cancer (TNBC); however, its effectiveness is often compromised by drug-related toxicity and resistance development. Herein, we aimed to evaluate whether an improved antineoplastic effect could be achieved in vitro and in vivo in TNBC by combining dovitinib, a multi-kinase inhibitor, with calcitriol, a natural anti-cancer hormone. In vitro, cell proliferation and cell-cycle distribution were studied by sulforhodamine B-assays and flow cytometry. In vivo, dovitinib/calcitriol effects on tumor growth, angiogenesis and endothelium activation were evaluated in xenografted mice by caliper measures, Itgb3-immunohistochemistry and 99mTc-RGD2-tumor uptake. The drug combination elicited a synergistically improved antiproliferative effect in TNBC-derived cells, which allowed a 7-fold dovitinib dose-reduction. Mechanistically, the co-treatment induced cell death and accumulation in S and G2/M phases, while inhibited tumor growth to a greater extent than each compound alone. Tumor uptake of 99mTc-RGD2 was reduced by dovitinib, suggesting angiogenesis inhibition, which was corroborated by decreased endothelial cell growth and tumor vessel density. In summary, calcitriol synergized dovitinib anticancer effects in vitro and in vivo, allowing for a significant dose-reduction of dovitinib, while maintaining its antiproliferative potency. Our results suggest the beneficial convergence of independent antitumor mechanisms of dovitinib and calcitriol to inhibit TNBC-tumor growth.

Capacity Expansion Models (CEMs) are optimization models used for long-term energy planning on national to continental scale. They are typically computationally demanding, thus in need of simplification, where one such simplification is to reduce the temporal representation. This paper investigates how using representative periods to reduce the temporal representation in CEMs distorts results compared to a benchmark model of a full chronological year. The test model is a generic CEM applied to Europe, equipped with a novel formulation for storage in model versions with reduced temporal representation. We test the performance of reduced models at penetration levels of wind and solar of 90%. Three measures for accuracy are used: (i) system cost, (ii) total capacity mix and (iii) regional capacity. We find that: (i) the system cost is well represented (~5% deviation from benchmark) with as few as ten representative days, (ii) the capacity mix is in general fairly well (~20% deviation) represented with 50 or more representative days, and (iii) the regional capacity mix displays large deviations (>50%) from benchmark for as many as 250 representative days. We conclude that modelers should be aware of the error margins when presenting results on these three aspects.

In this work, magnetic CuFe₂O₄/Ag nanoparticles activated by porous covalent organic frameworks (COF) was fabricated to evaluate the heterogenous reduction of 4-nitrophenol (4-NP). The core-shell CuFe₂O₄/Ag@COF was successfully prepared by polydopamine reduction of silver ions on CuFe₂O₄ nanoparticles, followed by COF layer condensation. With integrating the intrinsic characteristics of the magnetic CuFe₂O₄/Ag core and COF layer, the obtained nanocomposite exhibited features of high specific surface area (464.21 m² g^-1), ordered mesoporous structure, strong environment stability, as well as fast magnetic response. Accordingly, the CuFe₂O₄/Ag@COF catalyst showed good affinity towards 4-NP via π-π stacking interactions and possessed enhanced catalytic activity compared with CuFe₂O₄/Ag and CuFe₂O₄@COF. The pseudo-first-order rate constant of CuFe₂O₄/Ag@COF (0.77 min^-1) is 3 and 5 times higher than CuFe₂O₄/Ag and CuFe₂O₄@COF, respectively. The characteristics of bi-catalytic CuFe₂O₄/Ag and the porous COF shell of CuFe₂O₄/Ag@COF made a contribution to improve the activity of 4-NP reduction. The present work demonstrated a facile strategy to fabricate COF activated nano-catalysts with enhanced performance in the fields of nitrophenolic wastewater treatment.

Redox reactions are of great importance in environmental catalysis. Gold nanoparticles (NPs) have attracted much attention because of their catalytic activity and their localized surface plasmon resonance (LSPR). In the present study, we investigated in details the reduction of ferricyanide (III) ion into ferrocyanide (II) ion catalyzed by spherical gold nanoparticles of two different sizes 15 nm and 30 nm and excited at their LSPR band. Experiments were conducted in the presence (or not) of sodium thiosulfate. This catalysis is enhanced in the presence of Au-NPs under visible light excitation. This reduction takes also place even without sodium thiosulfate. Our results demonstrate the implication of hot electrons in this reduction.

Traditional winglets are designed as fixed devices attached at the tips of the wings. The primary purpose of the winglets is to reduce the lift-induced drag, therefore improving aircraft performance and fuel efficiency. However, because winglets are fixed surfaces, they cannot be used to control lift-induced drag reductions or to obtain the largest lift-induced drag reductions at different flight conditions (take-off, climb, cruise, loitering, descent, approach, landing, and so on). In this work, we propose the use of variable cant angle winglets which could potentially allow aircraft to get the best all-around performance (in terms of lift-induced drag reduction), at different flight phases. By using computational fluid dynamics, we study the influence of the winglet cant angle and sweep angle on the performance of a benchmark wing at Mach numbers of 0.3 and 0.8395. The results obtained demonstrate that by adjusting the cant angle, the aerodynamic performance can be improved at different flight conditions.

The development and generalization of Digital Volume Correlation (DVC) on X-ray computed tomography data highlight the issue of long term storage. The present paper proposes a new model-free method for pruning the DVC data. The size of the remaining sampled data can be user-defined, depending on the needs concerning storage space. The data pruning procedure is deeply linked to hyper-reduction techniques. The DVC data of a resin-bonded sand tested in uniaxial compression is used as an illustrating example. The relevance of the pruned data is tested afterwards for model calibration. A new Finite Element Model Updating (FEMU) technique coupled with an hybrid hyper-reduction method is used to successfully calibrate a constitutive model of the resin bonded sand with the pruned data only.

Multiobjective optimization plays an increasingly important role in modern applications, where several criteria are often of equal importance. The task in multiobjective optimization and multiobjective optimal control is therefore to compute the set of optimal compromises (the Pareto set) between the conflicting objectives. The advances in algorithms and the increasing interest in Pareto optimal solutions have led to a wide range of new applications related to optimal and feedback control which results in new challenges such as expensive models or real-time applicability. Since the Pareto set generally consists of an infinite number of solutions, the computational effort can quickly become challenging which is particularly problematic when the objectives are costly to evaluate or when a solution has to be presented very quickly. This article gives an overview over recent developments in accelerating multiobjective optimal control for complex problems where either PDE constraints are present or where a feedback behavior has to be achieved. In the first case, surrogate models yield significant speed-ups. Besides classical meta-modeling techniques for multiobjective optimization, a promising alternative for control problems is to introduce a surrogate model for the system dynamics. In the case of real-time requirements, various promising model predictive control approaches have been proposed, using either fast online solvers or offline-online decomposition. We also briefly comment on dimension reduction in many-objective optimization problems as another technique for reducing the numerical effort.

We study a two-echelon supply chain made up of a supplier and a manufacturer, both of which can reduce their component/product carbon emissions. With the vertical technology spillovers, we explore the optimal decisions of centralized and decentralized supply chains with price dependent demand and propose coordination strategy for the decentralized supply chain. Considering the cost contraction effectiveness of the technology spillovers, the centralized and decentralized game theoretic models of a two-echelon supply chain are developed to investigate optimal decisions of pricing and carbon emissions reduction. Through a systematic comparison and numerical analysis, we show that the profits of both players and the entire supply chain improve with the effect of technology spillovers increasing. Carbon emissions reduction will be taken by various protective measures so that the supplier and the manufacturer who do not innovate can hardly share the results of innovating via the “free-riding” methods when the technology spillover is relatively small. We also propose a revenue-cost sharing contract through bargaining to enhance the performance of the decentralized supply chain.

Climate change is a major development challenge to Ethiopia. Unless adaptation measures are widely implemented, climate change can set back development efforts and achievements by years. Recognizing this, the Government of Ethiopia (GoE) and civil society organizations have since recently been making considerable efforts to tackle the climate change problem. This paper documents the experience of CARE International in Ethiopia in facilitating bottom-up approaches to promote community-led disaster risk management and climate change adaptation planning through a participator scenario planning (PSP) methodology. PSP is a coordinated approach which leverages a variety of stakeholders' skills and mandates to explore potential climate change risks and their impacts, and then develop locally relevant and shared adaptation action plans that support livelihoods, social capital and ecosystem resilience. The approach has facilitated timely access to and communication of seasonal climate advisories which in turn is empowering communities to take advantage of opportunities that climate presents, which is a key part of adapting to climate change. The institutionalization of the approach by district and regional disaster prevention and food security coordination offices in the southern pastoral regions of Ethiopia encouraged integration of PSP into community livelihood adaptation and local government development planning, hence continuity of the process. Sustainability is expected to be fully achieved when local government planning processes recognize the importance of and provides resources for the participation of meteorological services and community forecasting experts to help refine plans on a seasonal basis, and for systems for dissemination of advisories. Key words: Climate Change, Disaster Risk Reduction, Adaptation, Pastoralism, Ethiopia,

Nearly 15 million patients undergo cosmetic surgery in the United States each year, with breast augmentations such as implants, lifts, or reductions being some of the most common procedures. The most common complications of these procedures are scarring and infection at the incision site, which often necessitates expensive corrective surgery. After significant weight loss, the patient in this study underwent an elective lower body lift in conjunction with a breast reduction and nipple-areolar transplant. An autologous skin graft was used at the transplant donor site. The skin graft unfortunately necrosed, warranting the need for rapid wound closure to avoid further pain and infection. The patient was treated for eight weeks with conservative measures. After eight weeks of failed attempts to close her wound, she was referred for specialist care. Upon initial examination, the donor site wound measured 3.5 cm x 3.5 cm with no sign of epithelialization. The patient received a single dose of Wharton’s jelly flowable perinatal tissue allograft and five hyperbaric oxygen therapy treatments over seven weeks. Upon inspection at the final examination, the wound was closed entirely with 100% epithelialization overlying granulation tissue. This case study demonstrates a precedent for the application of Wharton’s jelly flowable allografts in complicated cosmetic post-surgical wounds. Future efforts will be directed at applying Wharton’s jelly allografts on a preventative basis. Preventative applications could be in stage 2 pressure sores or intra-operatively to decrease potential patient suffering, prevent emotional distress, and reduce unnecessary healthcare expenses.

Background Nitrous Oxide (N₂O) is a dissociative anaesthetic that is sometimes used recreationally. The prevalence of N₂O use is difficult to quantify but appears to be increasing. Research on N₂O harms and application of harm reduction strategies are limited. The aim of this mixed method systematic review was to collate and synthesise the disparate body of research on recreational nitrous oxide use to inform harm reduction approaches tailored for young people. Methods To identify publications reporting recreational use of N₂O, a search of public health, psychology and social science databases was conducted. Databases included PubMed, CIHNAL, PsycINFO, Scopus and Web of Science. Gray literature and Google advanced search were also used. Due to limited published literature on the recreational use of N₂O, no limit was placed on publication date or study type. A thematic synthesis extracted descriptive and analytical themes from the selected studies. Quality appraisal was conducted using the CASP Tool for Qualitative studies and the Joanna Briggs Institute case report assessment tool Results The search retrieved 407 reports. Thirty-four were included in the final analysis including sixteen case reports. The included studies were primarily concerned with raising awareness of the apparently increasing use and subsequently increasing harms of recreational N₂O use. There was limited reference to policy or legislative responses in any published studies, no suggestions for harm reduction strategies or application of service level responses. In general, individuals lack awareness of N2O related harms. Conclusion The review found three key areas that deserve further consideration including: 1) policy, 2) service delivery, and 3) harm associated with N₂O use. We recommend a top-down (policy) and bottom-up (services delivery/services users) approach to harm reduction for N₂O use which also includes further consultation and research with both groups. Future research could explore young people’s experience of N₂O use including benefits and problems to inform contextually relevant harm reduction strategies.

Environmental tax is the climate policy that offers, in theory, the easiest way for carbon reduction. But in practice, implementation has proven complicated despite public demand for policy action on climate change. This research investigates to reframe environmental taxes in ways more personally engaging to create a moral foundation, and massive participation. As people show rising demand, we aimed to design a tool that responds to public expectations and operates directly at source on emission reducers, viz the trees. Drawing on research from environmental taxes and the evidence of measures taken, we reasoned that an environmental fiscal policy may not intend necessarily to punish the “bads”, but rather might reward the positive attitude and direct it to act. Consequently, we focused on tax reliefs and designed Green Aid, that can address people’s attitude to take active participation into account by incorporating virtuous behaviours into tax relief. Green Aid Tax relief works embedded in the Green Aid Participation Scheme that bears directly on a source of environmental recovery and organizes the global call to public action in a sustained, structured, and collective participation to forestation. Green Aid bridges the action of contributing to carbon reduction with immediate, tangible, and direct benefits. It can be an alternative environmental tax, able to address and operate directly at source on emission reducers and secure effectiveness in carbon reduction and efficiency in terms of public acceptance and viability at a global level.

Under the goal of carbon peak and carbon neutrality, the carbon emission reduction of the automobile industry has attracted more and more attention in recent years. Electric vehicle has the dual attributes of power load and energy storage unit. With the increase of the number of electric vehicles, reducing carbon emissions through the collaborative interaction between electric vehicle and power network will become an important way to control carbon emissions in the automotive field. In this study, an optimization model of emission reduction benefits based on integrated development of electric vehicle and power grid is proposed, which explores the best technical way of synergy between power grid and electric vehicle, achieves the best carbon reduction effect and provides a model basis for large-scale demonstration application. Numerical simulations based on the real case in Beijing are conducted to validate the effectiveness of the proposed method.

This work is driven by a practical question, corrections of Artificial Intelligence (AI) errors. Systematic re-training of a large AI system is hardly possible. To solve this problem, special external devices, correctors, are developed. They should provide quick and non-iterative system fix without modification of a legacy AI system. A common universal part of the AI corrector is a classifier that should separate undesired and erroneous behavior from normal operation. Training of such classifiers is a grand challenge at the heart of the one- and few-shot learning methods. Effectiveness of one- and few-short methods is based on either significant dimensionality reductions or the blessing of dimensionality effects. Stochastic separability is a blessing of dimensionality phenomenon that allows one-and few-shot error correction: in high-dimensional datasets under broad assumptions each point can be separated from the rest of the set by simple and robust linear discriminant. The hierarchical structure of data universe is introduced where each data cluster has a granular internal structure, etc. New stochastic separation theorems for the data distributions with fine-grained structure are formulated and proved. Separation theorems in infinite-dimensional limits are proven under assumptions of compact embedding of patterns into data space. New multi-correctors of AI systems are presented and illustrated with examples of predicting errors and learning new classes of objects by a deep convolutional neural network.

Cultivated land plays an important role in water and soil loss in the earth-rocky mountainous region, northern China, however, its responses to soil control measures and rainfall characteristics are still not fully understood. In this study, 85 erosive rainfall events in 2011-2019 were grouped into three types, and the responses of runoff and soil loss on five cultivated plots with different slopes in the upstream catchment of the Miyun Reservoir to soil conservation measures and rainfall regimes were evaluated. Results found that event-averaged runoff depths and soil loss rates on the five plots ranged from 7.05 mm to 0.03 mm and from 300.51 t km-2 to 0.37 t km-2 respectively, depending on rainfall regimes, soil conservation measures, and slope gradients. The high occurring frequency (i.e., 72.94%) rainfall regime A with short rainfall duration (RD), low rainfall amount (P), and high mean rainfall intensity (Im) yielded lower runoff depth and higher soil loss rate. Rainfall regime B with longer RD, and higher P and Im, however, produced higher rainfall depth and lower soil loss rate. Terraced plot had the highest runoff and soil loss reduction efficiencies of over 96.03%. Contour tillage had comparable sediment reduction efficiency to that of the terraced plot on gentle slopes (gradient less than 11.0%), while its runoff reduction efficiency was less than 13.11%. This study implies that in the Miyun Reservoir catchment and similar regions in the world, contour tillage should be promoted on gentle slopes, and terrace construction should be given enough attention since it can greatly reduce water quantity and cause water shortage in downstream catchments.

Nowadays, speed up development and use of digital devices such as smartphones have put people at risk of internet crimes. The evidence of present crimes in a computer file can be easily unreachable by changing the prefix of a file or other algorithms. In more complex cases, either file divided into different parts or the parts of a file that has information about the file type are deleted, where the file fragment recognition issue is discussed. The known files are divided into different fragments, and different classification algorithms to solve the problems of file fragment recognition. A confusion matrix measures the accuracy of type recognition. In the present study, first, the file is divided into different fragments. Then, the file fragment features, which are obtained from Binary Frequency Distribution (BFD), are reduced by 2 feature reduction algorithms; Sequential Forward Selection algorithm (SFS) as well as Sequential Floating Forward Selection algorithm (SFFS) to delete sparse features that result in increased accuracy and speed. Finally, the reduced features are given to 3 classifier algorithms, Multilayer Perceptron (MLP), Support Vector Machines (SVM), and K-Nearest Neighbor (KNN) for classification and comparison of the results. In this paper, we proposed the algorithm of file type recognition that can recognize 6 types of useful files ( pdf, txt, jpg, doc, html, exe), which may distinguish a type of file fragments with higher accuracy than the similar works done.

Recent preclinical studies have shown the potential benefits of short-term calorie reduction (SCR) on cancer treatment. In this integrative review, we aimed to identify and synthesize current evidence regarding the feasibility, process, and effects of SCR in cancer patients receiving chemotherapy. PubMed, Cumulative Index to Nursing and Allied Health Literature, Ovid Medline, PsychINFO, and Embase were searched for original research articles using various combinations of Medical Subject Heading terms. Among the 311 articles identified, seven studies met the inclusion criteria. The majority of the reviewed studies was small randomized controlled trials or cohort study with fair quality. The results suggest that SCR is safe and feasible. SCR is typically arranged around the chemotherapy with the duration ranging from 24 to 96 hours. Most studies examined the protective effects of SCR on normal cells during chemotherapy. The evidence supports that SCR had the potential to enhance both physical and psychological wellbeing of patients during chemotherapy. SCR is a cost-effective intervention with great potential. Future well-controlled studies with sufficient sample sizes are needed to examine the full and long-term effects of SCR and its mechanism of action.

There are many pollution and environment problem in the human ecosystem. There are different methods are used to removal of sulfur from sour gases for example Basic Claus process and Modified Claus process . There are different chemical software are used for simulation and optimization of Claus process for example Aspen Plus and Chemcad ECT. The Gibbs free energy method is introduced and model of Claus process. There are new parameter are introduced in reaction furnace to reduce the error from 33% to 7 %. The waste heat boiler is installed at the reaction furnace in which high pressure stream is produced and study the decomposition the hydrogen sulphide. The new rate of reaction is introduced of the enhancement of H2 production in chemical process. The simulation of reaction furnace in Aspen plus software is the maximum utilization of process. Due to suitable operating condition of reaction furnace is caused the maximum destruction of ammonia gas in the reactor. When we are increasing the oxygen concentration and temperature of feed is causing decreasing the ammonia production in reaction furnace. It is below than acceptance value of ammonia is 150 ppm in the reaction furnace. The presence of oxygen components, Sulfur oxide, hydroxide components are effect on decreasing the amount of ammonia in furnace and temperature is about at 1350⁰C. It is noted that when the production of sulfur recovery is decrease in Claus process and the production of carbon monoxide is increase in the thermal section at the existence. Now we are work on parametric studies of furnace that could be causes the production of ammonia destruction and CO emission in the Claus process. Due to optimize the reaction furnace parameter are help to get large of sulfur production, ammonia gas destruction, increased the catalyst life and decreased of dangerous gases.

In this research, an attempt was made to reduce the dimension of wavelet-ANFIS/ANN (artificial neural network/adaptive neuro-fuzzy inference system) models toward reliable forecasts as well as to decrease computational cost. In this regard, the principal component analysis was performed on the input time series decomposed by a discrete wavelet transform to feed the ANN/ANFIS models. The models were applied for dissolved oxygen (DO) forecasting in rivers which is an important variable affecting aquatic life and water quality. The current values of DO, water surface temperature, salinity, and turbidity have been considered as the input variable to forecast DO in a three-time step further. The results of the study revealed that PCA can be employed as a powerful for dimension reduction of input variables and also to detect inter-correlation of input variables. Results of the PCA-Wavelet-ANN models are compared with those obtained from Wavelet-ANN models while the earlier one has the advantage of less computational time than the later models. Dealing with ANFIS models, PCA is more beneficial to avoid Wavelet-ANFIS models creating too many rules which deteriorate the efficiency of the ANFIS models. Moreover, manipulating the Wavelet-ANFIS models utilizing PCA leads to a significant decreasing in computational time. Finally, it was found that the PCA-Wavelet-ANN/ANFIS models can provide reliable forecasts of dissolved oxygen as an important water quality indicators in rivers.

This paper presents an investigation into the influence of drag-reducing polymer (DRP) on the flow of water inside and around U-bends. The DRPs tested were partially hydrolysed polyacrylamide (HPAM) and two different molecular weight polyethylene oxides (PEO). The Reynolds number and in-situ concentration ranges of water and DRP were and respectively. The test section was made up of clear polyvinyl chloride (CPVC) pipes that contained two U-bends with radii of curvature (R) of 100 and 200 mm as well as straight sections of 19-mm ID. Higher pressure gradient was recorded in the under-developed flow section after the bend. Drag reduction (DR) increased with in-situ concentration of the DRP and the flowrate up to some threshold values. The concentration and flowrate thresholds were about 20 ppm and 1.07 m/s respectively. DR differed among the different sections considered with the highest values recorded for developed flows upstream of the bend and the least values recorded in the bend. DR at station 1 (immediately after the bend) was generally lower than that at station 2 (further downstream). P-K Plots showed that, the DR envelop for developed flow in straight pipes did not apply to the bend and the under-developed flow section. DR increased with polymer molecular weight and ionic strength in straight sections. However, molecular weight (and polymer shearing) had limited effect on DR in the bends. DR characteristics at the bend suggested that there was a different or additional mechanism. The effect of bend curvature ratio on DR was predominant after the U-bend. The larger the ratio of pipe diameter to bend diameter, the lower the DR in the redeveloping sections after the bend. For R = 100 mm, the highest DR recorded for fully developed flows before bend, in the bend, at stations 1 and 2 were 57, 31, 36 and 33% respectively while that for R = 200 mm were 64, 28, 42 and 49% respectively.

The issues of metallic scrap management and its utilization in manufacturing plants are nowadays intensely considered to address essential sustainability guidelines. Efficient recycling procedure for shop floor metallic scrap is not yet available because of abundance and contamination of nonmetallic constituents. Other ferrous metallic scrap are melted and purified during secondary steelmaking to get products in the form of blooms and billets are obtained. This study illustrates the potential of powder technology (powder metallurgy (PM) and metal injection molding (MIM)) based process for solid-state recycling and attainment of usable products. Industrially downgraded grinding sludge is pulverized and used as a raw material. Results showed properties of sintered parts are significantly improved due to in-situ reduction and densification during sintering. Recyclability Index (RI) was created to compare the effect of process variables on obtained products. Based on RI, recycled ferrous parts have about 70% comparable properties with equivalent pure iron parts. Complex reduction and sintering behavior in MIM, particularly, diffusion and pore volume kinetics limits applicability of MIM with this recycling approach. However, few industrial parts were developed and manufactured by PM based approach to validate the applicability of this novel recycling-cum-manufacturing process for the production of porous parts.

High electricity demand for consumption at current supply level in Indonesia led to the rising cost of electricity bills. This factor is compounded by the fact that many electric generators in Indonesia still use fossil fuels, which contributes to the high basic generation cost. UBL is one of the universities that aim to be a green campus. Our research explores the possibility of installing motion sensor to contribute on the energy efficiency. Although mostly common in developed countries, the use of motion sensor for energy efficiency is still rare, especially in Indonesia. despite rising cost and supply shortages, Indonesian buildings are still of high energy consumption. our experiment shows that simple installation of commercially available motion sensors can contribute to reduce the electricity bill from the increase of energy efficiency. One of the efforts to lower energy demand in consumer side is to use the electricity efficiently, such as turning off lights in a room when it's not in use. This method can be simply done by turning the light switches for office and classrooms, but difficult to do in public spaces such as toilets and corridors. Our experiment shows that simple installation of commercially available motion sensors can contribute to reduce the electricity bill from the increase of energy efficiency. Automatic light switches experimentally installed in sample toilet room prove that electricity consumption from the lamps can contribute to the reduction of total weekly energy that translates into Green House Gas emission reduction.

Electronic structure calculations have been carried out to examine the effect of protonation and water molecules on the heme group of peroxidases in different redox (ferric, ferrous, compounds I and II) and spin states. Shared geometries, spectroscopic properties at Soret region, and thermodynamics of peroxidases are discussed. B3LYP and M06-2X density functionals with different basis sets were employed on a common molecular model of the active site (Fe-centred porphine and proximal imidazole). Computed Gibbs free energies indicate that the corresponding aquo complexes are not thermodynamically stable, supporting the five-coordinate Fe(III) centre in native ferric peroxidases, with a water molecule located at a non-bonding distance. Protonation of the ferryl oxygen of compound II is discussed in terms of thermodynamics, Fe–O bond distances, and redox properties. It is demonstrated that this protonation is necessary to account for the experimental data and computed Gibbs free energies that reveal pKa values of compound II about 8.5 – 9.0. Computation suggests that the origin of the general oxidative properties of peroxidase species, as well as their reactivity towards water and protons and Soret spectral properties, mostly resides on the iron porphyrin and its proximal ligand histidine.

Hazelnut is a widespread nut species, especially in Europe, that can be consumed raw or roasted, due to its pleasant taste and nutritional properties. Despite the renowned beneficial properties, hazelnuts contain several proteins capable of inducing food allergy in sensitized individuals such as Cor a 2 (profilin), Cor a 8 (lipid transfer protein), Cor a 9 (11S seed storage globulin, legumin-like) and Cor a 11 (7S seed storage globulin, vicilin-like). In the present paper we investigated the effectiveness of autoclave based treatments in decreasing the allergic potential of hazelnut as also assessed by submitting the treated material to in vivo skin prick test and to in vitro immunoblot analysis with sera of allergic individuals exposed to the treated food material. This preliminary analysis shows that autoclave treatment, preceded by hydration and/or followed by drying, seems to be a promising approach and appears to be effective in reducing the allergenicity of hazelnut in most patients, probably due to the denaturation of most major and minor allergenic proteins. This work will open to the opportunity to produce, in perspective, hypoallergenic hazelnut derivatives tolerated by the allergic subjects.

In this study, a novel porous geopolymer mortar (GP) was produced and tested experimentally. Industrial waste materials/by-products were used as constituents of the GP, along with dune sand. One sample was produced as a control sample for benchmarking. For the rest of the samples, 15%, 30%, and 45% by volume, the solid constituents were replaced with expanded polystyrene foam (EPS) beads. These mortar samples were heat cured to depolymerize the EPS to cause porosity inside the samples. Indoor experiments were conducted to evaluate the response of produced porous GP to high heat flux. The porous samples were able to reduce heat transmission across the opposite surfaces. Induced porosity resulted in a decrement in compressive strength from 77.2 MPa for the control sample to 15.8 MPa for 45% porous sample. However, the limit lies within the standards for partitioning walls in buildings and pavements in urban areas to absorb rainwater.

The paper proposes a new principle of finding and removing elements of mathematical model, redundant in terms of parametric identification of the model. It allows reducing computational and time complexity of the applications built on the model. Especially this is important for AI based systems, systems based on IoT solutions, distributed systems etc. Besides, the complexity reduction allows increasing an accuracy of mathematical models implemented. Despite the model order reduction methods are well known, they are extremely depended however on the problem area. Thus, proposed reduction principles can be used in different areas, what is demonstrated in this paper. The proposed method for the reduction of mathematical models of dynamic systems allows also the assessment of the requirements for the parameters of the simulator elements to ensure the specified accuracy of dynamic similarity. Efficiency of the principle is shown on the ordinary differential equations and on the neural network model. The given examples demonstrate efficient normalizing properties of the reduction principle for the mathematical models in the form of neural networks.

Convalescent blood product therapy has been introduced since early 1900s to treat emerging infectious disease based on the evidence that polyclonal neutralizing antibodies can reduce duration of viremia. Recent large outbreaks of viral diseases for whom effective antivirals or vaccines are still lacking has revamped the interest in convalescent plasma as life-saving treatments. This review summarizes historical settings of application, and surveys current technologies for collection, manufacturing, pathogen inactivation, and banking, with a focus on COVID-19.

The search for lower cost materials that reduce pressure drop in fluid transport systems in oil and gas industries to conserve pumping energy is of paramount importance. Polymers are known to reduce pressure drop in pipeline oil-water flows in a process referred to as drag reduction (DR). The effect of partially hydrolysed polyacrylamide, polyethylene oxide, aloe vera mucilage and their mixtures as drag reducing polymers (DRPs) on pressure gradient (pressure drop; Δp) in pipeline oil-water flows was studied. The experiment was carried out in flow rig with 0.02-m diameter straight unplasticised polyvinylchloride (uPVC) pipe, two centrifugal pumps, control valves and two storage tanks. Tap water (ρ = 997 Kg/m³ and µ = 0.89 cP) and diesel (ρ = 832 Kg/m³ and µ = 1.66 cP) were used as the test fluid at ambient condition. The polymer mixture total concentration (MTC) of 30 and 400 ppm at different mixing proportion, mixture Reynolds number (Re_mix) and oil input volume were investigated. The results show increase in pressure gradient with increase in oil input volume in both single-phase water flow and oil-water flow before adding drag reducing polymers (DRPs). But Δp decreased after adding DRPs with increase in Reynolds number (Re) or Re_mix and decrease in the oil-phase Re, vice versa. The results further showed higher reduction in pressure drop by the polymer mixture than in each of the polymer used at the same conditions. The rigidness of the biopolymer was improved by adding synthetic polymers which result to increase in DR efficiency.The search for lower cost materials that reduce pressure drop in fluid transport systems in oil and gas industries to conserve pumping energy is of paramount importance. Polymers are known to reduce pressure drop in pipeline oil-water flows in a process referred to as drag reduction (DR). The effect of partially hydrolysed polyacrylamide, polyethylene oxide, aloe vera mucilage and their mixtures as drag reducing polymers (DRPs) on pressure gradient (pressure drop; Δp) in pipeline oil-water flows was studied. The experiment was carried out in flow rig with 0.02-m diameter straight unplasticised polyvinylchloride (uPVC) pipe, two centrifugal pumps, control valves and two storage tanks. Tap water (ρ = 997 Kg/m³ and µ = 0.89 cP) and diesel (ρ = 832 Kg/m³ and µ = 1.66 cP) were used as the test fluid at ambient condition. The polymer mixture total concentration (MTC) of 30 and 400 ppm at different mixing proportion, mixture Reynolds number (Re_mix) and oil input volume were investigated. The results show increase in pressure gradient with increase in oil input volume in both single-phase water flow and oil-water flow before adding drag reducing polymers (DRPs). But Δp decreased after adding DRPs with increase in Reynolds number (Re) or Re_mix and decrease in the oil-phase Re, vice versa. The results further showed higher reduction in pressure drop by the polymer mixture than in each of the polymer used at the same conditions. The rigidness of the biopolymer was improved by adding synthetic polymers which result to increase in DR efficiency.

Microbial populations involved in forming the distinctive precipitates of the S, Fe, Mn, and Ca cycles in the San Diego River watershed reflect an interplay between mineralogy of the rocks in the watershed, sparse rainfall, ground- and surface-water anoxia, and runoff of high sulfate, treated imported water. In the less developed headwaters, Temescal Creek tributary emerges from pyrite-bearing metamorphic rocks, and thus exhibits both an oxidized Fe and reduced S cycle. In the middle reaches, the river moves through developed land where treated, imported high sulfate Colorado River water enters from urban runoff. Mast Park surrounded by caliche-bearing sedimentary rocks is a site where marl is precipitating. Cobbles in riffles in the river are coated black with Mn oxide. When the river encounters deep-seated volcanic bedrock, it wells up to precipitate both Fe and Mn oxides at Old Mission Dam. Then, directly flowing through caliche-laced sedimentary rocks, Birchcreek tributary precipitates tufa. Further downstream, at a site that periodically receives full sunlight, a sulfuretum sets up during the summer when the river is deoxygenated. Such a rich geochemistry results in activity of iron and manganese oxidizing bacteria, sulfur oxidizers and reducers, and cyanobacteria precipitating calcareous marl and tufa.

Vanadium titano-magnetite is a significant resource in China, and in this study, we characterize its isothermal reduction mechanisms in the mixture of H₂, CO, and N₂ where the variables considered here include reduction time, reduction temperature, gas composition, and pellet size. The kinetics of the reduction process are mainly studied, which follows a shrinking core model. The results indicate that the reduction degree of oxidized VTM pellets increases with the increase of reduction time, reduction temperature but decreases with the increase of pellet size. Moreover, we found that an increase of H₂/(H₂+CO) ratio induces an increase of the reduction degree. Then the transformation of main Ti-bearing mineral phases is discussed, and the most probable reaction mechanism is revealed. In the whole reduction process, the kinetic results confirm the existence of an early stage and a latter stage, which are controlled by interface chemical reaction and diffusion, respectively. Furthermore, the results show that the diffusion-control step can be observably shortened with the decrease of pellet size because a thinner product layer is formed during the reduction process. Our study thus provides a valuable technical basis on the VTM industrial application.

Recent wastewater testing suggests the poliovirus is reemerging, raising questions about the efficacy of the current inactivated polio vaccine and mass vaccination to eradicate poliomyelitis. The present study reassessed reported outcomes from the placebo-control study of the 1954 Salk inactivated poliomyelitis vaccine field trial, which studied a population of 1,829,916 U.S. school children from the first three grades. The placebo-control study of the trial reported that the polio vaccine was 80% to 90% effective in reducing cases of laboratory confirmed paralytic poliomyelitis, 60% to 70% effective against type 1 of the virus, and greater than 90% effective against types 2 and 3 of the poliovirus. However, these outcomes are reported as relative risk reductions, and the absolute risk reductions of the 1954 polio vaccine field trial were never reported to the public. The present paper’s analysis reveals to the public for the first time that the inactivated poliomyelitis vaccine's absolute risk reduction of laboratory confirmed paralytic poliomyelitis in the placebo-control study is 0.01% to 0.02%, an extraordinarily low clinical effect that impugns the Salk polio vaccine’s reported effectiveness. Furthermore, absolute risk reductions for the three poliovirus types are 0.01%, 0.00%, and 0.01%, respectively. Outcome reporting bias in the 1954 inactivated poliomyelitis vaccine field trial casts doubt on eradication of the poliovirus through mass vaccination.

The prospects of processing blast furnace and steelmaking sludge using Waelz process in a laboratory rotary kiln is shown. The influence of varying thermal treatment modes, furnace atmosphere and type of reducing agents on the level of zinc reduction from sludges was analyzed. In general, the blast furnace sludge contains a high portion of iron (approx.48 wt. %) and can be reused as a charge after satisfactory zinc reduction. It was found that N- atmosphere and high content of the graphite or coke oven reducing agent in combination with high temperature can reduce the content of Zn in the sludge to 0.08 wt. % at 1200 °C for mixture of steelmaking and blast furnace sludge. A significant reduction in the Zn content to 0.66 wt. % occurs at 1100 °C. The content and type of reducing agent play an important role; graphite has shown a better reducing ability compared to coke oven dust. When nitrogen is used, zinc is reduced even without an additional reducing agent, since the carbon contained in the sludge is made use of for the reduction. In an air atmosphere, without the use of a reducing agent, there was no reduction in the Zn content.

Compared with precious metal catalysts, non-platinum catalysts have the advantages of low cost and high performance. Among them, the activated carbon (AC) with a large specific surface area (SSA) can be used as a carrier or as a carbon source of nonprecious metal/carbon system catalyst at the same time. Therefore, this paper uses cheap pine peel bio-based materials to prepare large surface area activated carbon and then compound with cobalt phthalocyanine (CoPc) to obtain a high-performance cobalt/nitrogen/carbon catalyst. The merits include AC@CoPc composite catalysts are prepared by precisely controlling the composite proportion of AC and CoPc, the atomically dispersed Co nanoparticles form and synergistically with N promote the exposure of CoNx active sites, and the Eonset of the catalyst treated with a composite proportion of AC and CoPc of 1 to 2 at 800 °C (AC@CoPc-800-1-2) is 1.01 V, which is higher than Pt/C (20 wt%) catalyst. Apart from this, the stability is 87.8% in 0.1 M KOH after 20000 s testing in compared with other AC@CoPc series catalysts and Pt/C (20 wt%) catalyst. Considering from the performance and price of the catalyst in practical application, these composite catalysts combine biomass carbon materials with phthalocyanine series, which will be widely used in the area of nonprecious metal catalysts.

The energy crisis and environmental problems are becoming more and more severe due to the long-term consumption of fossil fuels. Therefore, energy conversion devices with high energy density and environmental friendliness (such as fuel cells, metal-air batteries, etc.) have been ex-pected to be reliable alternatives to traditional fossil energy. However, due to the inevitable use of precious metals as the electrode catalysts for these devices, the popularization of these alternatives is seriously hindered. Transition metal nitrides (TMNs) exhibit similar surface and adsorption properties to noble metals since the atomic distance between metal atoms increases and the d-band center of metal atoms downshift after the nitrogen atoms enter the metal lattice. TMNs have become one of the best electrode materials to replace noble metal electrocatalysts in energy storage and conversion devices. In this review, the latest development in the electrocatalytic ap-plication of TMNs nanocrystalline is covered. Firstly, we briefly discuss the structure and activity origin of TMNs and introduce the common physical and chemical methods for the preparation of TMNs. Subsequently, we illustrate the applications of unary TMNs and multivariate TMNs in oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). Finally, we summarize the challenges and problems of TMNs encountered at the present stage, and expect its future de-velopment.

A winemaking waste was used as a precursor of activated carbon used in hazardous Cr(VI) removal from solutions. The preparation process consisted of a hydrothermal process, and a chemical activation, of the resulting product, with KOH. The adsorption results showed that the adsorption of Cr(VI) on the obtained activated carbon is strongly dependent on the stirring speed applied to the carbon/solution mixture, pH of the solution, and temperature. The equilibrium isotherm was well fitted to the Langmuir type-II equation, whereas the kinetic can be described by the pseudo-second-order kinetic model. Thermodynamic studies revealed that Cr(VI) adsorption was an exothermic and spontaneous process. Finally, desorption experiments showed that Cr(VI) was effectively desorbed using hydrazine sulfate solutions, and at the same time, the element was reduced to the less hazardous Cr(III) oxidation state.

This paper presents a multifunctional reflective digital metasurface of arbitrary base based on voltage tunable liquid crystal (LC). The reflective digital metamaterial can be multiplexed for different desirable functions by properly biasing the LC for different code patterns. Simulation results of three significant functions, beam steering with a steering elevation angle 27° at 75 GHz, RCS reduction of at least 15dB along the incident direction, and beam shaping with different beam shapes have been presented to prove the concept.

A review of influence of drag-reducing agents on curved pipe flows is presented in this work. In addition, this review outlined proposed mechanism, friction factor and fluid flux models for drag-reducing agents in curved pipe flows. Our finding reveals that drag reduction by additives in curved pipes is quite significant but generally lower than the corresponding drag reduction in straight pipes. It decreases with increase in curvature ratio and more pronounced in the transition and turbulent flow regimes. Drag reduction strongly depends on the polymers and surfactants’ concentrations as well as the bubble fraction of micro-bubbles. It is also reported that drag reduction in curved pipes depends on temperature and existence of dissolved salts in the fluids. Maximum drag reduction asymptote differed between straight and curved pipes and between polymer and surfactant. No definite conclusion could be drawn as regards drag reduction for two-phase flow in curved pipes due to the limited studies in this area. Many questions such as the mechanism of drag reduction in curved pipes and how drag-reducing agents interact with secondary flows still remained unanswered. Hence, some research gaps have been identified with recommendations for areas of future researches.

Objective: This study investigated the effect of the hierarchical medical system under the national health insurance program on resident’s healthcare-seeking behavior in Taiwan. Background: Healthcare authorities in Taiwan initiated the allowance reduction of outpatient visits at regional hospitals and higher hierarchical hospitals from 2018. The ultimate goal is to implement a hierarchical medical system and provide the residents accessible as well as consistent medical services. Methods: This research was conducted through the questionnaire survey method and data were collected between August and December 2018 from the records of subjects who had recently sought medical attention. A total of 1,340 valid questionnaires were returned. Results: Regarding the effect on healthcare-seeking behavior, the following factors were significant: being aged between 40 to 49 (p＜.1), subjects with an educational background of junior high school (p＜.05), those who were not aware of the policy (p＜.001), and an awareness about both the hierarchical medical system and the policy to reduce outpatient visits to large hospitals (p＜.001). Conclusion: The public should be made aware about the hierarchical medical system to improve healthcare.

In Qinglong ore field, paleo-oil reservoir is found to be associated with antimony deposits, and they have close genetic relationship. In this study, aromatics geochemistry of paleo-oil reservoir bitumen was studied to further discuss the thermochemical sulfate reduction (TSR) reaction and the mechanism of antimony mineralization. A total of 124 aromatic compounds were identified by Gas chromatography-mass spectrometry (GC–MS) analysis in bitumen samples, including abundant phenanthrene series, dibenzothiophene series, fluoranthene series, chrysene series, and a small number of fluorene series, naphthalene series, dibenzofuran series, biphenyl series, triaromatic steroid series. Aromatic parameters such as trimethylnaphthalene index (TMNr), methylphenanthrene index (MPI), methylphenanthrene distribution fraction (MPDF, F1 and F2), methyldibenzothiophene parameter (MDR), C28TAS-20S/(20R+20S), and benzofluoranthene/benzo[e]pyrene indicate Qinglong paleo-oil reservoir is in over maturity level. The abundance of phenanthrene and chrysene aromatic compounds and a small amount of naphthalene series, benzofluoranthene, fluoranthene, pyrene, anthracene, retene, perylene and biphenyl suggest that the parent material of the paleo-oil reservoir was mainly low aquatic organisms, mixed with a small amount of higher plant. The detected a certain number of compounds, such as retene, triaromatic steroid series and perylene, the ternary diagram of DBF–DBT–F and binary plot of Pr/Ph–DBT/P, DBT/(F+DBT)–DBF/(F+DBF) and Pr/Ph–DBT/DBF reveal that the source rock of the paleo-oil reservoir was formed in the marine environment of weak oxidation and weak reduction. The comprehensive analysis shows that the Qinglong paleo-oil reservoir originated from Devonian source rocks, just like other paleo-oil reservoirs and natural gas reservoirs in the Nanpanjiang basin. Abundant dibenzothiophene series were detected, indicating that the paleo-oil reservoir underwent a certain degree of TSR reaction. We believe that the paleo-gas reservoir formed by the evolution of paleo-oil reservoir participated in antimony mineralization, that is, hydrocarbon organic matter acted as reducing agent and transformed SO42− in oilfield brine into H2S through TSR, providing reduced sulfur and creating environmental conditions for mineralization.

We refute a recently proposed thought experiment namely the Dead-Alive Physicist (DAP) whose authors claim it to be the falsification of the von Neumann interpretation in Quantum Mechanics. We discover major flaws in their model and our justification serves the purpose of disregarding further claims and assertions made in the paper at various stages. Thus, in a yet another situation, it is proven that the formalism advanced by von Neumann is non-trivial and non-falsifiable.