Immunosensors have been widely developed to use antibodies to detect a pathogen of interest; it is interesting to look at the effect of nonspecific antibody binding to E. coli using electrochemical methods. IgG antibody not specific to E. coli O157:H7 was crosslinked onto a screen-printed carbon electrode. The presence of E. coli at 4, 4 × 10², 4 × 10⁵, and 4 × 10⁸ CFU/mL on the electrode surface was detected via linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS). Current transfer at both electrodes was reduced as the concentration of bacteria increased; however, the calibration of number of cells to decreased current was nonlinear for IgG-modified electrodes. The nonlinearity is confirmed by EIS measurements which showed highest impedance at 4 CFU/mL E. coli when impedance should be the lowest. FESEM images showed higher binding of cells when IgG is present compared to electrodes with reduced graphene oxide (rGO) alone. Electrodes with rGO alone show less attachment of E. coli, with EIS showing a linear calibration profile, while LSV shows not much difference in current values for all concentrations aside from the highest concentration. These results suggest that nonspecific binding can provide false signals in electrochemical measurements, and it is crucial to provide proper controls.

Not only does this paper present a novel type-2 fuzzy system for identification and behavior prognostication of an experimental solar cell set and a wind turbine, but also it brings forward an exquisite technique to acquire an optimal number of membership functions and the corresponding rules. It proposes a seven-layered NCPRT2FS. For fuzzification in the first two layers, Gaussian type-2 fuzzy membership functions with uncertainty in the mean, are exploited. The third layer comprises rule definition and the forth one embeds fulfillment of type reduction. The three last remained layers are the ones in which resultant left–right firing points, two end-points and output all get assessed correspondingly. It should not be neglected off the nutshell that recurrent feedback at the fifth layer exerts delayed outputs ameliorating efficiency of the suggested NCPRT2FS. Later in the paper, a modern structural learning, established on type-2 fuzzy clustering, is held forth. An adaptively rated learning back-propagation algorithm is extended to adjust the parameters ensuring the convergence as well. Eventually, solar cell photo-voltaic and wind turbine are deemed as case studies. The experimental data are exploited and the consequent yields emerge so persuasive.

Wheat and barley are among the primary food resources of the world population; therefore, their growth and observation are essential in farms to enhance food security worldwide. On top of that, careful observation of the product is essential to find solutions for the issues faced during their production and to reduce the impacts of weather changes. With the advancement of Remote Sensing technology, the observation and estimation process has increased. In this study, numbers of spectral vegetation indices was used along with canopy biophysical properties ( LAI ) and biochemical properties (chlorophyll), there calculated from (Landsat 8 and Sentinel-2) satellite data. The wheat and barley samples were collected before were be ready for harvest, and a relation with the vegetarian indices was established using the Multi-Linear Regression module, in which the equations used in predicting the harvest were developed and used to create a graph for expected harvest. The result indicated that there is a strong relationship between the vegetation indices of Sentinel-2 and Landsat images and the actual grain yield with R² of 0.77 and 0.71, respectively. The results show that the strongest correlation is observed between the LAI data obtained from Sentinel data and cereal yield data, with an R² 0.68, and the highest correlation for the indices of Landsat images is observed in the NDWI with R² 0.59 and the lowest degree of error was in the root mean square error (RMSE) for the Sentinel-2 and Landsat 8 with 0.57 and 1.54. In addition, this study also showed that the least relationship for grain yield prediction was observed between the NDRI for Sentinel-2 (R² 0.1) and SAVI for Landsat image (R² 0.47).

We present a new mathematical model of disease spread reflecting specialties of covid-19 epidemic by elevating the role social clustering of population. The model can be used to explain slower approaching herd immunity in Sweden, than it was predicted by a variety of other mathematical models; see graphs Fig. \ref{GROWTH2}. The hierarchic structure of social clusters is mathematically modeled with ultrametric spaces having treelike geometry. To simplify mathematics, we consider homogeneous trees with $p$-branches leaving each vertex. Such trees are endowed with algebraic structure, the $p$-adic number fields. We apply theory of the $p$-adic diffusion equation to describe coronavirus' spread in hierarchically clustered population. This equation has applications to statistical physics and microbiology for modeling {\it dynamics on energy landscapes.} To move from one social cluster (valley) to another, the virus (its carrier) should cross a social barrier between them. The magnitude of a barrier depends on the number of social hierarchy's levels composing this barrier. As the most appropriate for the recent situation in Sweden, we consider {\it linearly increasing barriers.} This structure matches with mild regulations in Sweden. The virus spreads rather easily inside a social cluster (say working collective), but jumps to other clusters are constrained by social barriers. This behavior matches with the covid-19 epidemic, with its cluster spreading structure. Our model differs crucially from the standard mathematical models of spread of disease, such as the SIR-model. We present socio-medical specialties of the covid-19 epidemic supporting our purely diffusional model.

For a dynamical system, it is known that the existence of a Lyapunov density implies almost global stability of an equilibrium. It is then natural to ask whether the existence of a common Lyapunov density for a nonlinear switched system implies almost global stability, in the same way as a common Lyapunov function implies global stability for nonlinear switched systems. In this work, the answer to this question is shown to be affirmative as long as switchings satisfy a dwell-time constraint with an arbitrarily small dwell time. As a straightforward extension of this result, we employ multiple Lyapunov densities in analogy with the role of multiple Lyapunov functions for the global stability of switched systems. This gives rise to a minimum dwell time estimate to ensure almost global stability of nonlinear switched systems, when a common Lyapunov density does not exist. The results obtained for continuous-time switched systems are based on some sufficient conditions for the almost global stability of discrete-time non-autonomous systems. These conditions are obtained using the duality between Frobenius-Perron operator and Koopman operator.

This research work focused on the risks we are faced with on our day to day activities, either directly or indirectly, which can gradually accumulates and results to communal crisis, religious crisis, socio-economic agitations and tribal crises. Nasarawa Eggon Local Government Area of Nasarawa State was used as case study and a well structure close–ended questionnaire was used for data collection as it relates to Controlled Self Risk Assessment (CSRA) and linear programming technique was used to analyze. The results proved that many of this processes were neglected in these communities, making them to be prone to incessant communal crisis. The study recommend that Government should strongly, as a matter of urgency address the unemployment rate, distribution of political position, schools, primary health care and equip security personnel with the modern technology facilities, which happen to record the highest risk level.

A large number of bridges are designed and built without considering seismic actions and, differently from buildings, there are currently no comprehensive guidelines to evaluate existing bridges without performing, as in the well known incremental dynamic analysis (IDA), complex non linear dynamic analyses (RHA). Bridges are structurally very different from building but, at the same time, are sensitive to higher modes as well as many multi-storey buildings that inspired innovative pushover procedures such as the well known modal pushover analysis (MPA). In the present study the incremental modal pushover analysis (IMPA), a pushover based approach already proposed and applied on buildings by the same authors, is revised and proposed for bridges (IMPAβ). IMPAβ accounts for the effects of higher modes in order to accurately estimate the seismic response of bridges; the effect of higher modes is considered by introducing a suitable number of modes to ensure the participation of a predefined total effective modal mass. The efficiency of the proposed method is demonstrated by conducting a study on two bridges, one regular and one irregular, and the IDA analysis is employed as reference solution. Numerical results indicate good accuracy of the proposed method in assessing the seismic response and a very good accuracy if compared to other available pushover procedures available in the literature.

Abstract: Nonlinear spectrum distortions are caused by the peculiarities of the operation of charge-coupled device elements (CCD), in which the signal exposition time (TINT) is one of the significant parameters. A change of TINT on a CCD leads to a nonlinear distortion of the resulting spectrum. Nonlinear distortion of the spectrum, in its turn, leads to errors in determining the central wavelength of Fiber Bragg Gratings (FBG) and spectrally sensitive sensors, which, in general, negatively affects the accuracy of measuring systems. The paper proposes an algorithm for correcting nonlinear distortions of the spectrum obtained on a spectrum analyzer using CCD as a receiver. It is shown that preliminary calibration of the optical spectrum analyzer with subsequent mathematical processing of the signal makes it possible to make corrections in the resulting spectrum, thereby leveling the errors caused by measurements at different TINT.

Genomic selection (GS) can accelerate variety improvement when training set (TS) size, and its relationship with the breeding set (BS) are optimized for prediction accuracies (PA) of genomic prediction (GP) models. Sixteen GP algorithms were run on phenotypic best linear unbiased predictors (BLUPs) and estimators (BLUEs) of resistance to both fall armyworm (FAW) and maize weevil (MW) in a tropical maize panel. For MW resistance, 37% of the panel was the TS, and BS was the remainder whilst for FAW, random-based training sets (RBTS) and pedigree-based training sets (PBTS) were designed. PAs achieved with BLUPs varied from 0.66 to 0.82 for MW resistance traits, and, for FAW resistance, 0.694 to 0.714 for RBTS of 37%, and 0.843 to 0.844 for RBTS of 85%, and, these were at least two-fold those from BLUEs. For PBTS, FAW resistance PAs were generally higher than those for RBTS, except for one dataset. GP models generally showed similar PAs across individual traits whilst the TS designation was determinant since a positive correlation (R=0.92***) between TS size and PAs was observed for RBTS and, for the PBTS, it was negative (R=0.44**). This study pioneers the use of GS for maize resistance to insect pests in sub-Saharan Africa.

The ASCE-EWRI reference evapotranspiration (ETo) equation is recommended as a standardized method for reference crop ETo estimation. However, various climate data as input variables to the standardized ETo method are considered limiting factors in most cases and restrict the ETo estimation. This paper assessed the potential of different machine learning (ML) models for ETo estimation using limited meteorological data. The ML models used to estimate daily ETo included Gene Expression Programming (GEP), Support Vector Machine (SVM), Multiple Linear Regression (LR), and Random Forest (RF). Three input combinations of daily maximum and minimum temperature (Tmax and Tmin), wind speed (W) with Tmax and Tmin, and solar radiation (Rs) with Tmax and Tmin were considered using meteorological data during 2003–2016 from six weather stations in the Red River Valley. To understand the performance of the applied models with the various combinations, station, and yearly based tests were assessed with local and spatial approaches. Considering the local and spatial approaches analysis, the LR and RF models illustrated the lowest rate of improvement compared to GEP and SVM. The spatial RF and SVM approaches showed the lowest and highest values of the scatter index as 0.333 and 0.457, respectively. As a result, the radiation-based combination and the RF model showed the best performance with higher accuracy for all stations either locally or spatially, and the spatial SVM and GEP illustrated the lowest performance among models and approaches.

Indian cities are increasingly becoming susceptible to PM10 induced health effects which have become a matter of concern for the policymakers of the country. Air pollution is engulfing the comparatively smaller cities as the rapid pace of urbanization, and economic development seems not to lose steam ever. A review of air pollution of 28 cities of India, which includes tier-I, II, and III cities of India, found to have grossly violated both WHO and NAAQS standards in respect of acceptable daily average PM10 concentrations by a wide margin. Predicting the city level PM10 concentrations in advance and accordingly initiate prior actions is an acceptable solution to save the city dwellers from PM10 induced health hazards. Predictive ability of three models, linear MLR, nonlinear MLP (ANN), and nonlinear CART, for one day ahead PM10 concentration forecasting of tier-II Guwahati city, were tested with 2016-2018 daily average observed climate data, PM10, and gaseous pollutants. The results show that the non-linear algorithm MLP with feedforward backpropagation network topologies of ANN class, giving the best prediction value when compared with linear MLR and nonlinear CART model. ANN (MLP) approach, therefore, may be useful to effectively derive a predictive understanding of one day ahead PM10 concentration level and thus provide a tool to the policymakers for improving decision-making associated with air pollution and public health.

Since the electro-hydraulic servo shaking table exists many nonlinear elements, such as, dead zone, friction and blacklash, its acceleration response has higher harmonics which result in acceleration harmonic distortion, when the electro-hydraulic system is excited by sinusoidal signal. For suppressing the harmonic distortion and precisely identify harmonics, a combination of the adaptive linear neural network and least mean M-estimate (ADALINE-LMM), is proposed to identify the amplitude and phase of each harmonic component. Namely, the Hampel’s three-part M-estimator is applied to provide thresholds for detecting and suppressing the error signal. Harmonic generators are used by this harmonic identification scheme to create input vectors and the value of the identified acceleration signal is subtracted from the true value of the system acceleration response to construct the criterion function. The weight vector of the ADALINE is updated iteratively by the LMM algorithm, and the amplitude and phase of each harmonic, even the results of harmonic components, can be computed directly online. The simulation and experiment are performed to validate the performance of the proposed algorithm. According to the experiment result, the above method of harmonic identification possesses great real-time performance and it has not only good convergence performance but also high identification precision.

Reliable fatigue design rules affect the proactive identification of safety parameters in aerospace industry. Numerous fatigue crack initiation and propagation models, linear and nonlinear, have been developed for designing purposes or estimation of the remaining life of aging airplanes. Depending on the adopted assumptions, the accuracy varies for different loading histories, loading types, and materials. Semi empirical models are simple but yield significant inaccuracies. Models with better theoretical basis provide better accuracy, but implementation in real conditions is problematic. In the present work, a review of author’s recent fatigue crack initiation and propagation models based on physical mechanisms is presented and improvements are proposed. Verification of the models on test results is provided and discussed.

Studies have shown that in many practical applications, data interpolation by splines leads to better approximation and higher computational efficiency as compared to data interpolation by a single polynomial. Data interpolation by splines can be significantly improved if knots are allowed to be free rather than at a priori fixed locations such as data points. In practical applications, the smallest possible curvature is often desired. Therefore, optimal splines are determined by minimizing a derivative of continuously differentiable functions comprising the spline of the required order. The problem of obtaining an optimal spline is tantamount to minimizing derivatives of a nonlinear differentiable function over a Banach space on a compact set. While the problem of data interpolation by quadratic splines has been accomplished analytically, interpolation by splines of higher orders or in higher dimensions is challenging. In this paper, to overcome difficulties associated with the complexity of the interpolation problem, the interval over which data points are defined, is discretized and continuous derivatives are substituted by their discrete counterparts. It is shown that as the mesh of the discretization approaches zero, a resulting near-optimal spline approaches an optimal spline. Splines with the desired accuracy can be obtained by choosing an appropriate mesh of the discretization. By using cubic splines as an example, numerical results demonstrate that the linear programming (LP) formulation, resulting from the discretization of the interpolation problem, can be solved by linear solvers with high computational efficiency and resulting splines provide a good approximation to the optimal splines.

Statistical mechanics investigates how emergent properties of macroscopic systems (such as temperature and pressure) relate to microscopic state fluctuations. The underlying idea is that global statistical descriptors of order and variability can monitor the relevant dynamics of the whole system at hand. Here we test the possibility of extending such an approach to psychotherapy research investigating the possibility of predicting the outcome of psychotherapy on the sole basis of coarse-grained empirical macro-parameters. Four good-outcome and four poor-outcome brief psychotherapies were recorded, and their transcripts coded in terms of standard psychological categories (abstract, positive emotional and negative emotional language pertaining to patient and therapist). Each patient-therapist interaction is considered as a discrete multivariate time series made of subsequent word-blocks of 150-word length, defined in terms of the above categories. Static analysis (Principal Component Analysis) highlighted a substantial difference between good-outcome and poor-outcome cases in terms of mutual correlations among those descriptors. In the former, the patient’s use of abstract language correlated with therapist’s emotional negative language, while in the latter it co-varied with therapist’s emotional positive language, thus showing the different judgment of the therapists regarding the same variable (abstract language) in poor and good outcome cases. On the other hand, the dynamic analysis, based on five coarse-grained descriptors related to variability, degree of order and complexity of the series, demonstrated a relevant case-specific effect, pointing to the possibility of deriving a consistent picture of any single psychotherapeutic process. Overall, the results showed that the systemic approach to psychotherapy (an old tenet of psychology) is mature to shift from a metaphorical to a fully quantitative status.

Pronounced differences exist in the biodiversity and structure of coral reef assemblages with increasing distance from shore, which may be expected given marked cross-shelf gradients in environmental conditions. Cross-shelf variation in the abundance of coral reef organisms is likely to be caused, at least in part, by differences in demography (e.g., growth and survival), though this has rarely been tested. This study quantified growth of three distinct coral taxa (Acropora nasuta, Pocillopora spp., and Stylophora pistillata) at 6 sites on Australia’s Great Barrier Reef (GBR), encompassing inshore, mid-shelf and outer-shelf reefs. Replicate colonies (up to 15 colonies per species, per reef) were stained using Alizarin red in December 2015 and retrieved 1-year later to quantify linear extension on replicate branches for each colony. Annual linear extension varied within and among coral taxa, with pronounced differences among reefs. For A. nausta. and S. pistillata, growth rates were highest at Orpheus Island, which is an inner shelf reef. However, inter-reef differences in coral growth were not explained by shelf position. Based on differences in skeletal density, which did vary according to shelf position, branching corals at the inshore sites may actually have higher rates of calcification compared to conspecifics on mid- and outer-shelf reefs. This study shows that growth of branching corals is not lower at inshore sites (and perhaps even higher) compared to sites at mid-shelf and outer reefs, despite generally higher levels of sedimentation and turbidity.

Nowadays, the fingerprinting methodologies of olive oils are dominated. They consider the entire analytical signal, which is acquired and recorded by the analytical instrument, directly from olive oil or isoleted fraction, i,e chromatogram. The shape and intensity of the recorded signal the instrumental fingerprint from the whole olive oil adulteration. Therefore, the methodolygy is based on the chemical composition (Fatty acids and Triglycerides compositions). However, Fatty acids composition as an indicator of purity suggests that linolenic acid content could be used as a parameter for the detection of extra virgin olive oil fraud with 5% of soybean oil. The adulteration could also be detected by the increase of the trans-fatty acid contents with 3% of soybean oil, 2% of corn oil and 4% of sunflower oil. The use of the ∆ECN42 proved to be effective in the Chemlali extra-virgin olive oil adulteration even at low levels: 1% of sunflower oil, 3% of soybean oil and 3% of corn oil. Therefore, compared to classical methods PCA and new approach of using LDA application could represent an alternative and innovative tool for faster and cheaper evaluation of extra-virgin olive oil adulteration.

This study investigated the trends of registered Death and Birth in Nigeria using Generalized Linear Models. Annual data on Death and Birth was collected from National Population Commission for the period of 2004 to 2017. The Natural increase calculated revealed a positive trend in the natural increase in Nigeria from 2004 to 2017. Evidence from summary statistics revealed some level of over dispersion (variance > mean). This study explored Poisson Regression Models and Negative Binomial Regression Models using two links (identity and log). The results revealed a positive increase in registration of birth and death rates in Nigeria and among the competing the models, Negative Binomial regression model with identity link emerged as the best model for modeling birth and death rates registration in Nigeria. Data on numbers of deaths and causes of death are essential if countries are to determine priorities, formulate and monitor policies for public health care as well as other government policies that may be based on such data

Bayesian nonlinear mixed effects models for data in the form of continuous, repeated measurements from a population, also known as Bayesian hierarchical nonlinear models, are a popular platform for analysis when interest focuses on individual specific characteristics and relevant uncertainty quantification. Due to the limitation of computational power, this framework was relatively dormant until the late 1980s, but in recent years, the statistical research community saw vigorous development of new methodological and computational techniques for these models, the emergence of software, and wide application of the models in numerous industrial and academic fields. This article presents an overview of the formulation, interpretation, and implementation of Bayesian nonlinear mixed effects models and surveys recent advances and applications.

In this paper, mean-field type games between two players with backward stochastic dynamics are defined and studied. They make up a class of non-zero-sum differential games where the players' state dynamics solve backward stochastic differential equations (BSDEs) that depend on the marginal distributions of player states. Players try to minimize their individual cost functionals, also depending on the marginal state distributions. Under some regularity conditions, we derive necessary and sufficient conditions for existence of Nash equilibria. Player behavior is illustrated by numerical examples, and is compared to a centrally planned solution where the social cost, the sum of player costs, is minimized. The inefficiency of a Nash equilibrium, compared to socially optimal behavior, is quantified by the so-called price of anarchy. Numerical simulations of the price of anarchy indicate how the improvement in social cost achievable by a central planner depends on problem parameters.

This study investigates the trend in monthly and annual rainfall, minimum and maximum temperature (T_min and T_max) using the Mann–Kendall (MK) test and Sen’s slope (SS) method and evaluates the significance of their variability for maize, sorghum and millet yields in northern Togo employing multiple regression analysis. The historical data of Kara, Niamtougou, Mango and Dapaong weather stations from 1977 to 2012 were used. Four non-parametric methods—Alexandersson’s Standard Normal Homogeneity Test (SNHT), Buishand’s Range Test (BRT), Pettitt’s Test (PT) and Von Neumann’s Ratio Test (VNRT)—were applied to detect homogeneity in the data. For the data which were serially correlated, a modified version of the MK test (pre-whitening) was utilised. Results showed an increasing trend in the annual rainfall in all four locations. However, this trend was only significant at Dapaong (p < 0.1). There was an increasing trend in T_max at Kara, Mango and Niamtougou, unlike Dapaong where T_max revealed a significant decreasing trend (p < 0.01). Similarly, there was an increasing trend in T_min at Kara, Mango and Dapaong, unlike Niamtougou where T_min showed a non-significant decreasing trend (p > 0.05). Rainfall in Dapaong was found to have increased (7.79 mm/year) more than the other locations such as Kara (2.20 mm/year), Niamtougou (4.57 mm/year) and Mango (0.67 mm). T_max increased by 0.13, 0.13 and 0.32 °C per decade at Kara, Niamtougou and Mango, respectively, and decreased by 0.20 per decade in Dapaong. Likewise, T_min increased by 0.07, 0.20 and 0.02 °C per decade at Kara, Mango and Dapaong, respectively, and decreased by 0.01 °C per decade at Niamtougou. Results of multiple regression analysis revealed nonlinear yield responses to changes in rainfall and temperature. Rainfall and temperature variability affects rainfed cereal crops production, but the effects vary across crops. The temperature has a positive effect on maize yield in Kara, Niamtougou and Mango but a negative effect on sorghum in Niamtougou and millet in Dapaong, while rainfall has a negative effect on maize yield in Niamtougou and Dapaong and millet yield in Mango. In all locations, rainfall and temperature variability has a significant effect on the cereal crop yields. There is, therefore, a need to adopt some adaptation strategies for sustainable agricultural production in northern Togo.

We present a new method of estimating fitness of countries and complexity of products by exploiting a non-linear non-homogeneous map applied to the publicly available information on the goods exported by a country. The non homogeneous terms guarantee both convergence and stability. After a suitable rescaling of the relevant quantities, the non homogeneous terms are eventually set to zero so that this new method is parameter free. This new map reproduces the findings of the method proposed by Tacchella et al. [1], and allows for an approximate analytic solution in case of actual binarized matrices based on the Revealed Comparative Advantage (RCA) indicator. This solution is connected with a new quantity describing the neighborhood of nodes in bipartite graphs, representing in this work the relations between countries and exported products. Moreover, we define the new indicator of country net-efficiency quantifying how a country efficiently invests in capabilities able to generate innovative complex high quality products. Eventually, we demonstrate analytically the local convergence of the algorithm.

In the present work we propose a dynamical mathematical model of the lung cells inflammation process in response to SARS-CoV-2 infection. In this scenario the main protease Nsp5 enhances the inflammatory process, increasing the levels of NF kB, IL-6, Cox2, and PGE2 with respect to a reference state without the virus. In presence of the virus the translation rates of NF kB and IkB arise to a high constant value, and when the translation rate of IL-6 also increases above the threshold value of 7 pg mL^-1 s^-1 the model predicts a persistent over stimulated immune state with high levels of the cytokine IL-6. Our model shows how such over stimulated immune state becomes autonomous of the signals from other immune cells such as macrophages and lymphocytes, and does not shut down by itself. We also show that in the context of the dynamical model presented here, Dexamethasone or Nimesulide have little effect on such inflammation state of the infected lung cell, and the only form to suppress it is with the inhibition of the activity of the viral protein Nsp5.To that end, our model suggest that drugs like Saquinavir may be useful. In this form, our model suggests that Nsp5 is effectively a central node underlying the severe acute lung inflammation during SARS-CoV-2 infection. The persistent production of IL-6 by lung cells can be one of the causes of the cytokine storm observed in critical patients with COVID19. Nsp5 seems to be the switch to start inflammation, the consequent overproduction of the ACE2 receptor, and an important underlying cause of the most severe cases of COVID19.

The Circular Economy of plastics is a promising concept that has the potential to reduce pollution and close the loop on plastic waste. However, further research is needed to develop more efficient and environmentally friendly methods of recycling plastic. This review article discusses the Circular Economy of plastics, its potential benefits and drawbacks, and the challenges that need to be addressed to make it a reality. Some case studies are also examined to explore how the Circular Economy of plastics has been implemented across the globe.

A rigorous model for the electron is presented by generalizing the Coulomb's Law or Gauss's Law of electrostatics, using a unified theory of electricity and gravity. The permittivity of the free-space is allowed to be variable, dependent on the energy density associated with the electric field at a given location, employing generalized concepts of gravity and mass/energy density. The electric field becomes a non-linear function of the source charge, where concept of the energy density needs to be properly defined. Stable solutions are derived for a spherically symmetric, surface-charge distribution of an elementary charge. This is implemented by assuming that the gravitational field and its equivalent permittivity function is proportional to the energy density, as a simple first-order approximation, with the constant of proportionality referred to as the Unifield Electro-Gravity (UEG) constant. The stable solution with the lowest mass/energy is assumed to represent a ``static'' electron without any spin. Further, assuming that the mass/energy of a static electron is half of the total mass/energy of an electron including its spin contribution, the required UEG constant is estimated. More fundamentally, the lowest stable mass of a static elementary charged particle, its associated classical radius, and the UEG constant are related to each other by a dimensionless constant, independent of any specific value of the charge or mass of the particle. This dimensionless constant is numerologically found to be closely related to the the fine structure constant. This possible origin of the fine structure constant is further strengthened by applying the proposed theory to successfully model the Casimir effect, from which approximately the same above relationship between the UEG constant, electron's mass and classical radius, and the fine structure constant, emerges.

The extensive deployment of wireless infrastructure provides a low-cost way to track mobile users in indoor environment. This paper demonstrates a prototype model of an accurate and reliable room location awareness system in a real public environment, where three typical problems arise. First, a massive number of access points (APs) can be sensed leading to a high-dimensional classification problem. Second, heterogeneous devices record different received signal strength (RSS) levels due to the variations in chip-set and antenna attenuation. Third, APs are not necessarily visible in every scanning cycle leading to missing data. This paper presents a probabilistic Wi-Fi fingerprinting method in a hidden Markov model (HMM) framework for mobile user tracking. Considering the spatial correlation of the signal strengths from multiple APs, a Multivariate Gaussian Mixture Model (MVGMM) is fitted to model the probability distribution of RSS measurements in each cell. Furthermore, the unseen property of invisible AP has been investigated in this research, and demonstrated the efficiency of differentiation between cells. The proposed system is able to achieve comparable localization performance. The filed test results present a reliable 97% localization room level accuracy of multiple mobile users in a real university campus WiFi network without any prior knowledge of the environment.

Background: In the functional data analysis (FDA), the hybrid or mixed data are scalar and functional datasets. The semi-functional partial linear regression model (SFPLR) is one of the first semiparametric models for the scalar response with hybrid covariates. Various extensions of this model are explored and summarized. Methods: Two first research articles, including “semi-functional partial linear regression model”, and “Partial functional linear regression” have more than 300 citations in Google Scholar. Finally, only 106 articles remained according to the inclusion and exclusion criteria such as 1) including the published articles in the ISI journals and excluding 2) non-English and 3) preprints, slides, and conference papers. We use the PRISMA standard for systematic review. Results: The articles are categorized into the following main topics: estimation procedures, confidence regions, time series, and panel data, Bayesian, spatial, robust, testing, quantile regression, varying Coefficient Models, Variable Selection, Single-index model, Measurement error, Multiple Functions, Missing values, Rank Method and Others. There are different applications and datasets such as the Tecator dataset, air quality, electricity consumption, and Neuroimaging, among others. Conclusions: SFPLR is one of the most famous regression modeling methods for hybrid data that has a lot of extensions among other models.

We report a large third-order nonlinear optical response of palladium diselenide (PdSe₂) films – a two-dimensional (2D) noble metal dichalcogenide material. Both open-aperture (OA) and closed-aperture (CA) Z-scan measurements are performed with a femtosecond pulsed laser at 800 nm to investigate the nonlinear absorption and nonlinear refraction, respectively. In the OA experiment, we observe optical limiting behaviour originating from large two photo absorption (TPA) in the PdSe₂ film of β = 3.26 ×10^-8 m/W. In the CA experiment, we measure a peak-valley response corresponding to a large and negative Kerr nonlinearity of n₂ = -1.33×10^-15 m²/W – two orders of magnitude larger than bulk silicon. We also characterize the variation of n₂ as a function of laser intensity, observing that n₂ decreases in magnitude with incident laser intensity, becoming saturated at n₂ = -9.96×10^-16 m²/W at high intensities. These results verify the large third-order nonlinear optical response of 2D PdSe₂ as well as its strong potential for high performance nonlinear photonic devices.

A variable annuity is a popular life insurance product that comes with financial guarantees. Using Monte Carlo simulation to value a large variable annuity portfolio is extremely time-consuming. Metamodeling approaches have been proposed in the literature to speed up the valuation process. In metamodeling, a metamodel is first fitted to a small number of variable annuity contracts and then used to predict the values of all other contracts. However, metamodels that have been investigated in the literature are sophisticated predictive models. In this paper, we investigate the use of linear regression models with interaction effects for the valuation of large variable annuity portfolios. Our numerical results show that linear regression models with interactions are able to produce accurate predictions and can be useful additions to the toolbox of metamodels that insurance companies can use to speed up the valuation of large VA portfolios.

In this letter, it is proposed that cryogenic quantum bits could operate based on the nonlinearity due to the quantum capacitance of two-dimensional Dirac materials, and in particular graphene. The anharmonicity of a typical superconducting quantum bit is calculated and the sensitivity of quantum bit frequency and anharmonicty with respect to temperature are found. Reasonable estimates reveal that a careful fabrication process could reveal the expected properties, thus putting the context of quantum computing hardware into new perspectives.

The work is devoted to the study of a MEMS resonator dynamics under the action of phase-locked and automatic gain control loops. Particular attention is directed to the study of the nonlinearity factor of the resonator elastic restoring force. It was found that the determination of control system parameters based on the stability analysis of the operating resonant mode, in the general case, does not provide the required phase adjustment and stabilization of the oscillation amplitude. Stable multifrequency modes of oscillations are found, an analytical study of the mechanisms of their appearance and evolution is carried out under variation of the key parameters of the system. The real regions of the control system stable operation are determined (which do not coincide, as was found, with the regions of stability of the operating resonant mode, due to the presence of hidden attractors in the phase space of the system). A methodology has been developed for identifying such areas of stable operation. A significant complication of the structure of possible motions in the system with an increase in the Q-factor of the resonator is revealed.

This paper reviews the low-resilience problem in many cities, poor designs of cities to cope with disasters, and the need for tolerance of urban constructions. It explores answers concerning the question of how shall we build cities resiliently? The method of this applied research is a multiphase process that considers all physical and socioeconomic elements of a city. It introduces six indicator groups of urban management (M), economy (E), built environments (U), Infrastructures (I), natural environments (N), and health protection (H). The groups include 55 indicators as variables in the mathematical calculations in this paper. This paper builds a mathematical model to maximize the profitability of resilient buildings by optimizing investments in the required projects. The projects will upgrade the firmness and tolerance of cities against nature-based and human-made dangers and risks. There is a linear programming in 55 variables to select optimal solutions from fifty-five factorial alternatives. Then, the programming will develop into non-linear programming. The unique innovation of this paper is its linear programming interpretation by non-linear to give optimal solutions for the problem. Applying the Lagrange function in the Kuhn-Tucker conditions proves the accuracy of the hypothesis that post-COVID urbanization requires maximum resilience. Only in this way, the urban economies will be free of risks. Outcomes in this paper will assist in the pre-planning, design, and building of built environments everywhere resilient and sustainable.

The fifth Generation (5G) mobile networks use millimeter Waves (mmWaves) to offer giga bit data rates. However, unlike microwaves, mmWave links are prone to user and topographic dynamics. They easily get blocked and end up forming irregular cell patterns for 5G. This in turn cause too early, too late, or wrong handoffs (HOs). To mitigate HO challenges, sustain connectivity and avert unnecessary HO, we propose a HO scheme based on Jump Markov Linear System (JMLS) and Deep Reinforcement Learning (DRL). JMLS is widely known to account for abrupt changes in system dynamics. DRL likewise emerges as an artificial intelligence technique for learning highly dimensional and time-varying behaviors. We combine the two techniques to account for time-varying, abrupt, and irregular changes in mmWave link behaviour by predicting likely deterioration patterns of target links. The prediction is optimized by meta training techniques that also reduces training sample size. Thus, the JMLS-DRL platform formulates intelligent and versatile HO policies for 5G. Results show our proposed prediction scheme about target link behavior post HO to be highly reliable. The scheme also averts unnecessary HOs thus ably supports longer dew time.

Efficient alternatives in energy production and consumption are constantly investigated by increasingly strict policies. In this way, the pollutant emissions that contribute to the greenhouse effect reduce and sustainability of the electricity sector increase. With more than a third of the world's energy consumption, buildings have great potential to contribute these sustainability goals. Additionally, with growing incentives in the Distributed Generation (DG) and Electric Vehicle (EV) industry, it is believed that Smart Buildings (SBs) can be a key in the field of residential energy sustainability in the future. In this work, an energy management system in SBs are developed to reduce the power demanded of a residential building. In order to balance the demand and power provided by the grid, microgrids such as Battery Energy Storage System (BESS), EVs and Photovoltaic Generation panels (PV) are used. Here, a Mixed Binary Linear Programming formulation (MBLP) is proposed to optimize the charge and discharge scheduling of EVs and also BESS. In order to show the efficiency of the model, a case study involving three scenarios and an economic analysis is considered. The results point a 65% reduction in peak load consumption supplied by grid and a 28.4% reduction in electricity consumption costs.

This study addresses an alternative use of viscous dampers (VDs) associated with buckling restrained braces (BRBs) as the innovative seismic protection devices. For this, 4, 8 and 12 storey steel frames were designed with 6.5 m equal span length and 4 m storey height. Thereafter, the VDs and BRBs were placed over the height of each frame considering three different configurations. The structures were modeled using SAP2000 finite element program and evaluated by the nonlinear time history analyses subjected to the six natural accelerograms (1976 Gazlı, 1978 Tabas, 1987 Superstition Hills, 1992 Cape Mendocino, 1994 Northridge and 1999 Chi-Chi). The structural response of the structures with and without VDs and BRBs were studied in terms of variation in the displacement, interstorey drift, absolute acceleration, maximum base shear, time history of roof displacement. The results clearly indicated that the application of VDs and BRBs had remarkable improvement in the earthquake performance of the case study frames by reducing the local/global deformations in the main structural systems and satisfied the serviceability.

In this paper, we study the gravitational lensing by some black hole classes within the non-linear electrodynamics in weak field limits. First, we calculate an optical geometry of the non-linear electrodynamics black hole then we use the Gauss-Bonnet theorem for finding deflection angle in weak field limits. The effect of non-linear electrodynamics on the deflection angle in leading order terms is studied. Furthermore, we discuss the effects of the plasma medium on the weak deflection angle.

This study presents a new kinetic scheme for the mass yield prediction of waste lignocellulosic biomasses treated by Hydrothermal Carbonization (HTC). The proposed reactions are based on the decomposition, solubilization, and polymerization of each main fraction of the biomass: cellulose, hemicellulose, and lignin. The ash content was assumed to be inert. The kinetic parameters have been obtained by non-linear adjustment using a data set with 220 experimental runs collected from the literature. The results indicate that the pre-exponential factors range was from 7.33 x10¹ to 1.412x10⁵ min^-1, and activation energies were between 33.75 y 225.3 kJ/mol. A good fit is achieved between the observed and predicted data with an R² of 0.81 and an RMSE of 7.7 %. The proposed scheme was validated with the experimental data obtained by the HTC of sawdust (Pinus radiata) and rapeseed (Brassica napus). The experiments were carried out at temperatures of 190, 220, and 250 ºC and reaction times of 0, 30, 60, 90, and 120 min. The predicted values showed an average error of 2.3 and 3.5 %, respectively. Therefore, the kinetic scheme is a useful tool in the conversion analysis of waste biomass treated by HTC.

3D city models are being extensively used in applications such as evacuation scenarios and energy consumption estimation. The main standard for 3D city models is the CityGML data model which can be encoded through the CityJSON data format. CityGML and CityJSON use polygonal modelling in order to represent geometries. True topological data structures have proven to be more computationally efficient for geometric analysis compared to polygonal modelling. In a previous study, we have introduced a method to topologically reconstruct CityGML models while maintaining the semantic information of the dataset, based solely on the combinatorial map (C-Map) data structure. As a result of the limitations of C-Map's semantic representation mechanism, the resulting datasets could suffer either from semantic information loss or the redundant repetition of them. In this article, we propose a solution for a more efficient representation of both geometry, topology and semantics by incorporating the C-Map data structure in the CityGML data model and implementing a CityJSON extension to encode the C-Map data. In addition, we provide an algorithm for the topological reconstruction of CityJSON datasets to append them according to this extension. Finally, we apply our methodology to three open datasets in order to validate our approach when applied to real-world data. Our results show that the proposed CityJSON extension can represent all geometric information of a city model in a lossless way, providing additional topological information for the objects of the model.

In this paper, a capacitor microphone system is presented to improve the conversion of mechanical energy to electrical energy using a nonlinear auto regressive moving average-L2 (NARMA-L2) and model predictive control (MPC) controllers for the analysis of the open loop and closed loop system. The open loop system response shows that the output voltage signal need to be improved. The comparison of the closed loop system with the proposed controllers have been analyzed and a promising result have been obtained using Matlab/Simulink.

Tidal stream energy, due to its high level of consistency and predictability, is one of the feasible and promising type of renewable energy for future development and investment. Applicability of Blade Element Momentum (BEM) method for modeling the interaction of turbines in tidal arrays has been proven in many studies. Apart from its well-known capabilities, yet there is scarcity of research using BEM for the modeling of tidal stream energy farms considering full scale rotors. In this paper, a real geographical site for developing a tidal farm in the southern coasts of Iran is selected. Then, a numerical methodology is validated and calibrated for the selected farm by analyzing array of turbines. A linear equation is proposed to calculate tidal power of marine hydrokinetic turbines. This methodology narrows down the wide range of turbine array configurations, reduces the cost of optimization and focuses on estimating best turbine arrangements in a limited number of positions.

Free volume is an extremely important intrinsic defect in polymers. Structurally, the free volume is the randomly distributed holes in the polymer molecular chain segments. From the perspective of molecular movement, it is also the space needed for the movement of molecular segments. In proton exchange membrane fuel cells, the free volume is also the space needed for the directional conduction of protons. Irradiation grafting sulfonated polyvinylidene fluoride (PVDF) is one of the methods to produce proton exchange membrane with good proton channel rate. Using the LYS-1 program, based on the linear absorption coefficient and backscatter coefficient models, the percentage of annihilated positrons in PVDF in the two-layer model and the three-layer model was studied, and comparing the two fitting results it is determined that the model closest to the positron annihilation percentage required by the PALS experiment is the two-layer model, which allows the percentage of positrons that are annihilated in PVDF films with a thickness of 100 μm to reach 46% using the high energy positron source ⁴⁴Ti without using the positron moderator. Using positron annihilation lifetime spectrum (PALS) analysis methods, based on Eldrup's classical model of free volume, the influence of absorbed doses of α particles on the free volume and crystallinity of PVDF was investigated, respectively. Based on the two test results the model of cross-linking and degradation of polyvinylidene fluoride irradiated by α particles was determined. Afterwards, X-ray diffraction (XRD) methods was used to study the change of PVDF crystal area before and after irradiation. The XRD results are consistent with the results measured by PALS.

In this paper, we investigate the effects of certain variants of the commutative laws on properties of several families of algebras which are in general not commutative, such as groups, linear algebras, or actually quite anti-commutative, such as $BCK$-algebras and $d$-algebras among others. From results obtained it becomes clear that by considering these variants in the presence of yet other axioms it is to be expected that a quite rich and varied set of results may be obtained both in the general and the particular setting of which what has been accomplished in this paper is a substantial sample.

The Landau damping effect was observed in collisionless plasma, as a microscopic resonant mechanism between electromagnetic radiation and the collective modes. In this paper we demonstrate the occurrence of the Landau damping at macroscopic scale in the interaction between water waves and anharmonic lattice of magnetic buoys. By coupling the Navier-Stokes equations for incompressible fluid with the nonlinear dynamics of an anharmonic magnetic lattice we obtain a resonant transfer of momentum and energy between the two systems. The velocity of the flow is obtained in the Stokes approximation with Basset type of drag force. The dynamics of the buoys is calculated in the surfactant approximation for a specific frequency, then we use Fourier analysis to obtain the general time variable interaction. After involving an integral Dirichlet transform we obtain the time dependent expression of the drag force, the interaction waves-lattice with a new term in the form of a Caputo fractional derivative. We compare the results of the model with experiments performed in a wave tank with free floating magnetic buoys under the action of small amplitude gravitational waves. This configuration can be applied in studies for the attenuation with resonant damping of rogue waves, storms or tsunamis.

Mints emit diverse scents that exert specific biological functions and are relevance for applications. The current work strives to develop electronic noses that can electronically discriminate the scents emitted by different species of Mint as alternative to conventional profiling by gas chromatography. Here, 12 different sensing materials including 4 different metal oxide nanoparticle dispersions (AZO, ZnO, SnO2, ITO), one Metal-Organic Frame as Cu(BPDC), and 7 different polymer films including PVA, PEDOT: PSS, PFO, SB, SW, SG, PB were used for functionalizing of QCM sensors. The purpose was to discriminate six economically relevant Mint species (Mentha x piperita, Mentha spicata, Mentha spicata ssp. crispa, Mentha longifolia, Agastache rugosa, and Nepeta cataria). The adsorption and desorption datasets obtained from each modified QCM sensor were processed by three different classification models including Principal Component Analy-sis (PCA), Linear Discriminant Analysis (LDA), and k-Nearest Neighbor Analysis (k-NN). This allowed discriminating the different Mints with classification accuracies of 97.2% (PCA), 100% (LDA), and 99.9% (k-NN), respectively. Prediction accuracies with a repeating test measurement reached up to 90.6% for LDA, and 85.6% for k-NN. These data demonstrate that this electronic nose can discriminate different Mint scents in a reliable and efficient manner.

The article analyzes Bernoulli 's binary sequences in representation of empirical events about the distribution of natural resources and population sizes. Considering the event as a nonlinear system, and consisting of two dependent random variables, with memory and probabilities in maximum finite or infinite lengths, constant and equal to ½ for both variables (stationary process). The expressions of the possible trajectories remain constant in sequences that are repeated alternating the presence or absence of one of the variables at each iteration (asymmetric). There are constant oscillations in the event except if the variables X₁ and X₂ are regulated as a function of time Y. It is observed that the variables X₁ and X₂ assume in time T_k → ∞ specific behaviors (geometric variable) that can be used as management tools for random systems. In this way, the article seeks to know from this analyzes, the maximum entropy of information in the system by a theoretical view and how to model resources distribution or containment in the given problem.

For a decade, the studies of dynamic control for unmanned aerial vehicles took a large interest, where drones as a useful technology in different areas were always suffering from several issues like instability-high energy consumption of batteries - inaccuracy of tracking targets. Different approaches are proposed for dealing with the non-linearity issues which present the most important features of this system. This paper describes our focus on the most common control strategies, known as model predictive control MPC, by developing a model based on the sensors embedded in our Tello quadrotor used for indoor purposes. The original controller of Tello quadrotor is supposed to be a slave, where the designed model predictive controller is created in MATLAB and imported to another embedded system, considered as a master; the objective of this model is to track the reference trajectory, almost keeping the stability of the system and ensure the low energy consumption. In the first part, a profound description of the modelling process of a dynamic model for drones is presented, explaining the design of MPC controller with both linear and non-linear strategies built in MATLAB. In the final part, simulation and results are discussed regarding its behaviour and performance, highlighting the MPC model's important role on drones' energy consumption profile.

In present work an opportunity of nearly single-cycle THz pulse generation in aperiodically poled lithium niobate (APPLN) crystal is studied. A radiating antenna model is used to simulate the THz generation from chirped APPLN crystal pumped by a sequence of femtosecond laser pulses with chirped delays m (m = 1, 2, 3 …) between adjacent pulses. It is shown that by appropriative choosing m it is possible to obtain temporally overlap of all THz pulses generated from positive (or negative) domains. It results in the formation of a nearly single-cycle THz pulse, if the chirp rate of domain length  in the crystal is sufficiently large. In opposite case, a few cycle THz pulses are generated with the number of the cycles depending on . The closed form expression for THz pulse form is obtained. The peak THz electric field strength of 0.3 MV/cm is predicted for APPLN crystal pumped by the sequence of laser pulses with peak intensity of the separate pulse in the sequence about 20 GW/cm2. By focusing the THz beam and by increasing the pump power the field strength can reach values of an order of few MV/cm.

For a given material, different shapes correspond to different rigidities. In this paper, the radii of the oblique elliptic torus are formulated, a nonlinear displacement formulation is presented and numerical simulations are carried out for circular, normal elliptic, and oblique tori, respectively. Our investigation shows that both the deformation and the stress response of an elastic torus are sensitive to the radius ratio, and indicate that the analysis of a torus should be done by using the bending theory of shells rather than membrance theory. A numerical study demonstrates that the inner region of the torus is stiffer than the outer region due to the Gauss curvature. The study also shows that an elastic torus deforms in a very specific manner, as the strain and stress concentration in two very narrow regions around the top and bottom crowns. The desired rigidity can be achieved by adjusting the ratio of minor and major radii and the oblique angle.

In this article, we consider the three dimensional $\alpha$-fractional nonlinear delay differential system of the form \begin{align*} D^{\alpha}\left(u(t)\right)&=p(t)g\left(v(\sigma(t))\right),\\D^{\alpha}\left(v(t)\right)&=-q(t)h\left(w(t))\right),\\D^{\alpha}\left(w(t)\right)&=r(t)f\left(u(\tau(t))\right),~ t \geq t_0, \end{align*} where $0 < \alpha \leq 1$, $D^{\alpha}$ denotes the Katugampola fractional derivative of order $\alpha$. We have established some new oscillation criteria of solutions of differential system by using generalized Riccati transformation and inequality technique. The obtained results are illustrated with suitable examples.

This study tries to focusing on applying information communication technology for economic importance of Mid Oil Company (MDOC), which is among contemporary oil companies in Iraq. Since ICT forms a significant aspect of achieving organizational economic objectives, most of public and private bodies seek to utilize ICT tool and techniques to improve work efficiencies. The emerging growth in ICT has made it process and service automation possible in managing organizational activities. To determine this effect of ICT on organizations, this study formulated statistical research model at MDOC through using fifteen questionnaires, which were distributed on three axes. The outcome of the questionnaire analysis revealed that there is inadequate comprehensive infrastructure to suitably support ICT within the selected organization management. In addition, it revealed that there are no ideal standards to maintain and sustain internet networks. Based on these revelations, the study presents recommendation for the adoption of ICT with the aim of minimizing cost, enhancing communication and managing infrastructure. Also recommends the need to support IT department within an organization, with essential equipment, in terms of man and machine, for better efficiency to employ the key of ICT Impact in Iraqi governmental oil companies.

Recently, due to the miniaturization of electronic products, printed circuit boards (PCBs) have also become smaller. This trend has led to the need for high-precision electrical test equipment to check PCBs for disconnections and short circuits. The purpose of this study is to improve the position repeatability of the platform unit up to ±2.5 μm in a linear stage type test equipment. For this purpose, the causes of position errors of the platform unit are analyzed. The platform unit holding the PCB is driven by a single-axis linear ball screw drive system offset from its geometric center due to design constraints. The yaw rotation of the platform is found to have a dominant effect on position repeatability. To address this problem, the methods of adding balancing weights to the platform unit and adjusting the stiffness of LM Guides are proposed. This reduces the yaw rotation by moving the centers of mass and stiffness closer to the linear ball screw actuator. In the verification tests, the position repeatability was decreased to less than ±1.0 μm.

The purpose of this study is to assess the concentration-response relations between conjunctivitis and exposure to ambient ozone. This retrospective study includes emergency department (ED) visits for conjunctivitis in Edmonton, Canada, for the period April 1992–March 2002. Daily average levels of ozone (range: 1.2–50.9, ppb), of temperature, and of relative humidity were estimated and used for the period of the study. For each of the considered exposure lags, (from 0 to 9 days), six different models were fitted to estimate the concentration-response function. The goodness of fit was assessed using the Akaike information criterion. During the period of the study, 17,211 ED visits for conjunctivitis were recorded and used. For all subjects together, a positive statistically significant association was obtained for the exposure lagged by 5 days. For female subjects, lags 1, 3, and 9 had positive statistically significant associations (lag 2 had negative associations). For male subjects, only lag 5 had a positive statistically significant association. The estimated non-linear concentration-response functions for the considered groups (all, males, females) and lags, revealed the associations along the exposure levels. The fitted shapes are described by algebraic functions and may have various forms. The estimated functions are useful to determine the risk associated with exposure to ground-level ozone.

The goal of this contribution is an application of the Linear General Model Predictive Control (LGMPC). In this paper, stability of the LGMPC is proven by means of a demonstration of a Theorem stating a sufficient and constructive condition. This condition can be applied for calculating the weight matrices of the cost function in the optimisation problem in LGMPC. Lower bounds conditions are found for one of these matrices and then a system with saturation is taken into consideration. The conditions could be interpreted and discussions through physical aspects. The obtained results were tested by means of computer simulations and an example with a recover water process is considered.

Modern development of high-intensity and high-resolution X-ray technology allows detailed studies of the multiphoton absorption and scattering of X-ray photons by deep and subvalent shells of molecular systems on a wide energy range. The interpretation of experimental data requires the improvement of computational methods for obtaining excited and ionized electron states of molecular systems with one or several vacancies. The specificity of solving these problems requires the use of molecular orbitals obtained in one-center representation. Slow convergence of one-center expansions is a significant disadvantage of this approach; it affects the accuracy of the calculation of spectroscopic quantities. We offer a method of including higher harmonics in one-center expansion of a molecular orbital with the use of wave functions of electrons of deep shells of a ligand (off-center atom of a molecule). The method allows one to take into account correctly electron density of a linear molecule near the ligand when describing vacancies created in a molecular core leading to radial relaxation of electron density. The analysis of the parameters of one-center expansion of the ligand functions depending on ligand’s charge is performed. The criteria for the inclusion of higher harmonics of one-center decomposition of the ligand functions in the molecular orbital are determined. The efficiency of the method is demonstrated by the example of diatomic molecules HF, LiF, and BF by estimating energy characteristics of their ground and ionized states.

The maximization of entropy S within a closed system is accepted as an inevitability (as the second law of thermodynamics) by statistical inference alone. The Maximum Entropy Production Principle (MEPP) states that not only S maximizes, but $\dot{S}$ as well: a system will dissipate as fast as possible. There is still no consensus on the general validity of this MEPP, even though it shows remarkable explanatory power (both qualitatively and quantitatively), and has been empirically demonstrated for many domains. In this theoretical paper I provide a generalization of entropy gradients, to show that the MEPP actually follows from the same statistical inference, as that of the 2nd law of thermodynamics. For this generalization I only use the concepts of super-statespaces and microstate-density. These concepts also allow for the abstraction of 'Self Organizing Criticality' to a bifurcating local difference in this density, and allow for a generalization of the fundamentally unresolved concepts of 'chaos' and 'order'.

Layered two-dimensional (2D) GO films are integrated with silicon-on-insulator (SOI) nanowire waveguides to experimentally demonstrate an enhanced Kerr nonlinearity, observed through self-phase modulation (SPM). The GO films are integrated with SOI nanowires using a large-area, transfer-free, layer-by-layer coating method that yields precise control of the film thickness. The film placement and coating length are controlled by opening windows in the silica cladding of the SOI nanowires. Owing to the strong mode overlap between the SOI nanowires and the highly nonlinear GO films, the Kerr nonlinearity of the hybrid waveguides is significantly enhanced. Detailed SPM measurements using picosecond optical pulses show significant spectral broadening enhancement for SOI nanowires coated with 2.2-mm-long films of 1−3 layers of GO, and 0.4-mm-long films with 5−20 layers of GO. By fitting the experimental results with theory, the dependence of GO’s n₂ on layer number and pulse energy is obtained, showing interesting physical insights and trends of the layered GO films from 2D monolayers to quasi bulk-like behavior. Finally, we show that by coating SOI nanowires with GO films the effective nonlinear parameter of SOI nanowires is increased 16 fold, with the effective nonlinear figure of merit (FOM) increasing by about 20 times to FOM > 5. These results reveal the strong potential of using layered GO films to improve the Kerr nonlinear optical performance of silicon photonic devices.

Cellular Nonlinear Networks (CNN) are a concept introduced in 1988 by Leon Chua and Lin Yang as a bio-inspired architecture, capable of massively parallel computation. Later on, CNN have been enhanced by incorporating designs that incorporate memristors to profit from their processing and memory capabilities. In addition, Stochastic Computing (SC) can be used to optimize the quantity of required processing elements; thus it provides a lightweight approximate computing framework, quite accurate and effective, though. In this work, we propose utilization of SC in designing and implementing a memristor-based CNN. As a proof of the proposed concept, an example of application is presented. This application combines Matlab and a FPGA in order to create the CNN. The implemented CNN has then been used to perform three different real-time applications on a 512x512 gray-scale and a 768x512 color image: storage of the image, edge detection, and image sharpening. It has to be pointed out that the same CNN has been used for the three different tasks, with the sole change of some programmable parameters. Results show an excellent capability with significant accompanying advantages, like the low number of needed elements further allowing for a low cost FPGA-based system implementation, something confirming the system’s ability for real time operation.

We present a model of infection dynamics that might explain slower approaching the herd immunity during the covid-19 epidemy in Sweden than it was predicted by a variety of other models; see graphs Fig. \ref{GROWTH2}. The new model takes into account the hierarchic structure of social clusters in the human society. We apply the well developed theory of random walk on the energy landscapes represented mathematically with ultrametric spaces. This theory was created for applications to spin glasses and protein dynamics. To move from one social cluster (valley) to another, the virus should cross a social barrier between them. The magnitude of a barrier depends on the number of social hierarchy's levels composing this barrier. As the most appropriate for the recent situation in Sweden, we consider linearly increasing (with respect to hierarchy's levels) barriers. This structure of barriers matches with a rather soft regulations imposed in Sweden in March 2020. In this model, the infection spreads rather easily inside a social cluster (say working collective), but jumps to other clusters are constrained by social barriers. This model's feature matches with the real situation during the covid-19 epidemy, with its cluster spreading structure. Clusters need not be determined solely geographically, they are based on a number of hierarchically ordered social coordinates. The model differs crucially from the standard models of spread of disease, such as the SIR-model. Our model describes such a specialty of spread of covid-19 virus as the presence of ``super-infectors'' who by performing a kind of random walk on a hierarchic landscape of social clusters spreads infection. In future, this model will be completed by adding the SIR-type counterpart. But, the latter is not a specialty of covid-19 spreading.

Quantum loops are processes that constitute quantum objects. In the causal model of quantum loops and quantum objects presented here, the nonlinear processes involve the elementary units of spacetime and the associated elementary units of quantum fields. As such, quantum loop processes are the sources of gravitational fields (i.e., spacetime curvature) and of the quantum objects wave function. The model may be viewed as a derivative of loop quantum gravity, spin networks and causal dynamical triangulation, although significant deviations to these theories exist. The causal model of quantum loops is based on a causal model of spacetime dynamics where space(-time) consists of interconnected space points, each of which is connected to a small number of neighboring space points. The curvature of spacetime is expressed by the density of these space points and by the arrangement of the connections between them. The quantum loop emerges in a nonlinear collective behavioral process from a collection of space points that carry energy and quantum field attributes.

In this article, we analyze the weak gravitational lensing in the context of Einstein-non-linear Maxwell-Yukawa black hole. To this desire, we derive the deflection angle of light by Einstein-non-linear Maxwell-Yukawa black hole using the Gibbons and Werner method. For this purpose, we obtain the Gaussian optical curvature and implement the Gauss-Bonnet theorem to investigate the deflection angle of Einstein-non-linear Maxwell-Yukawa black hole. Moreover, we derive the deflection angle of light in the presence of plasma medium. We also analyze the graphical behavior of deflection angle by Einstein-non-linear Maxwell-Yukawa black hole in the presence of plasma as well as non-plasma medium.

Astroviruses (AstVs) are occurs globally and are common causes of gastroenteritis in human and animals. The genetic diversity and epidemiology of AstVs in Africa is not well known, hence, we aimed to genetically characterize astroviruses in asymptomatic smallholder piglets in East Africa. Twenty-four samples randomly selected from 446 piglets (<6 months old), initially collected for rotavirus study, was sequenced for metagenomic analysis. Thirteen (13/24) samples had contigs with high identity to genus Mamastrovirus. Analysis of 7 strains with complete (or near complete) genome revealed variable nucleotide and amino acid sequence identities with known PoAstV strains. The U083 and K321 strains had nucleotide sequence similarities ranging from 66.4 to 75.4 % to the known PoAstV2 strains, nucleotide sequence similarity of U460 strain with known PoAstV3 ranged 57.0 to 65.1 % to the, while K062, K366, K451, and K456 strains showed nucleotide sequence similarities of 63.5 to 80 % to the known PoAstV4 strains. The low sequence identities (<90 %) indicate that novel genotypes of PoAstVs are circulating in the study area. Multiple recombination events were detected in our PoAstV4 strains, indicating that the genetic diversity observed in these strains may be due to recombination. Importantly, we identified potential candidate epitopes with conserved peptides in our PoAstV strains that could aid in the design of immune diagnosis tools and subunit vaccines. Our data provide new intuitions into the genetic structure of porcine astroviruses in East African.

Fusarium graminearum causes head blight in wheat and corn, and produces chemicals harmful for humans and other animals. It is important to understand how it grows in order to prevent outbreaks. There are 3 well-known growth models for microorganisms and they seem applicable to molds: linear, Gompertz and Baranyi. This study aimed to see which could better represent F. graminearum growth. Three replicates were grown in yeast extract agar (YEA) for 20 days. The Feret’s radius was measured in ImageJ software, and then related to the models. Linear model was the most closely correlated to the actual growth. Thus, considering that it was the most representative of the reality and it is easier to use, it seems to be the best logical choice for F. graminearum growth studies.

Ultra-wideband wavelength division multiplexed networks enable operators to use more effectively the bandwidth offered by a single fiber pair and thus make significant savings, both in operational and capital expenditures. The main objective of this study is to minimize optical node resources, such as transponders, multiplexers and wavelength selective switches, needed to provide and maintain high quality of network services, in ultra-wideband wavelength division multiplexed networks, at low cost. A model based on integer programming is proposed, which includes a detailed description of optical network nodal resources. The developed optimization tools are used to study the ultra-wideband wavelength division multiplexed network performance when compared with the traditional C-band wavelength division multiplexed networks. The analysis is carried out for realistic networks of different dimensions and traffic demand sets.

This paper proposes a model based on gene expression programming for predicting discharge coefficient of triangular labyrinth weirs. The parameters influencing discharge coefficient prediction were first examined and presented as crest height ratio to the head over the crest of the weir (p/y), crest length of water to channel width (L/W), crest length of water to the head over the crest of the weir (L/y), Froude number (F=V/√(gy)) and vertex angle () dimensionless parameters. Different models were then presented using sensitivity analysis in order to examine each of the dimensionless parameters presented in this study. In addition, an equation was presented through the use of nonlinear regression (NLR) for the purpose of comparison with GEP. The results of the studies conducted by using different statistical indexes indicated that GEP is more capable than NLR. This is to the extent that GEP predicts the discharge coefficient with an average relative error of approximately 2.5% in such a manner that the predicted values have less than 5% relative error in the worst model.

The quality of dietary patterns can be optimized using a mathematical technique known as linear programming (LP). LP methods have rarely been applied to individual meals. The present LP models optimized the breakfast meal for those participants in the nationally representative National Health and Nutrition Examination Survey 2011-2014 who ate breakfast (n=11,565). The Nutrient Rich Food Index (NRF9.3) was a measure of diet quality. Breakfasts in the bottom tertile of NRF9.3 scores (T1) were LP-modeled to meet nutrient requirements without deviating too much from current eating habits. Separate LP models were run for children and for adults. The LP-modeled breakfasts resembled the existing ones in the top tertile of NRF9.3 scores (T3), but were more nutrient-rich. Favoring fruit, cereals, and dairy, the LP-modeled breakfasts had less meat, added sugars and fats but more whole fruit and 100% juices, more whole grains, and more milk and yogurt. LP modeling methods can build on existing dietary patterns to construct food-based dietary guidelines and identify individual meals and/or snacks that need improvement.

In spite of numerous predictions, the natural herd immunity for covid-19 visru had not been approahed anywhere in the world. Thus, the traditional mathematical models of disease spread demonstrated their inability to describe adequately the covid-19 pandemic. In author's works, the novel model of the disease spread was developed. This model reflects the basic features of the covid-19 pandemic: a) the social clustering character of virus spread, b) . Social clustering is mathematically modelled with ultrametric spaces having the treelike geometry encoding hierarchy of the regulation constraints. The virus spread is described by ultrametric diffusion or random walk on the hierarchic energy landscape. In contrast to the standard models which are characterized by the exponential decrease of the probability to become infected - at the stage of approaching of the herd immunity, the ultrametric model is characterized by the power law. Moreover, the model gives the possibility to quantify the influence of restriction measures up to the lockdown. Our main result is that the play with restrictions, including lockdowns, is counterproductive and leads to the essential slowdown of approaching the herd immunity or even makes this impossible.

In this paper, we consider with a class of system of differential equations whose argument transforms are involution. In this an initial value problem for a differential equation with involution is reduced to an initial value problem for a higher order ordinary differential equation. Than either two initial conditions are necessary for a solution, the equation is then reduced to a boundary value problem for a higher order ODE.

This work presents a linear smoothing scheme over high-order triangular elements in the framework of a cell-based strain smoothed finite element method for two-dimensional nonlinear problems. The main idea behind the proposed linear smoothing scheme for strain-smoothed finite element method (S-FEM) is no subdivision of finite element cells to sub-cells while the classical S-FEM needs sub-cells. Since the linear smoothing function is employed, S-FEM is able to use quadratic triangular or quadrilateral elements. The modified smoothed matrix obtained node-wise is evaluated. In the same manner with the computation of the strain-displacement matrix, the smoothed stiffness matrix and deformation graident are obtained over smoothing domains. A series of benchmark tests are investigated to demonstrate validity and stability of the proposed scheme. The validity and accuracy are confirmed by comparing the obtained numerical results with the standard FEM using 2nd-order triangular element and the exact solutions.

Assuming a two component, positive and negative mass, superfluid/supersolid for space (the Winterberg model), we model the Higgs field as a condensate made up of a positive and a negative mass, planckion pair. The connection is shown to be consistent (compatible) with the underlying field equations for each field, and the continuity equation is satisfied for both species of planckions, as well as for the Higgs field. An inherent length scale for space (the vacuum) emerges, which we estimate from previous work to be of the order of,

We consider a model of predator-prey interaction at fractional-order where the predation obeys the ratio-dependent functional response and the prey is linearly harvested. For the proposed model, we show the existence, uniqueness, non-negativity as well as the boundedness of the solutions. Conditions for the existence of all possible equilibrium points and their stability criteria, both locally and globally, are also investigated. The local stability conditions are derived using the Magtinon's theorem, while the global stability is proven by formulating an appropriate Lyapunov function. The occurance of Hopf bifurcation around the interior point is also shown analytically. At the end, we implement the Predictor-Corrector scheme to perform some numerical simulations.

The fatty-acid profiles of five main commercial pistachio cultivars, including Ahmad-Aghaei, Akbari, Chrok, Kalle-Ghouchi and Ohadi, were determined by gas chromatography: palmitic (C16:0), palmitoleic (C16:1), stearic (C18:0), oleic (C18:1), linoleic (C18:2), linolenic (C18:3) arachidic (C20:0) and gondoic (C20:1) acid. Based on the oleic to linoleic acid (O/L) ratio, a quality index was determined for these five cultivars: Ohadi (2.40) < Ahmad-Aghaei (2.60) < Kale-Ghouchi (2.94) < Chrok (3.05) < Akbari (3.66). Principal component analysis (PCA) of the fatty-acid data yielded three significant PCs, which together account for 80.0% of the total variance in the data set. A linear discriminant analysis (LDA) model evaluated with cross validation correctly classified almost all samples: the average percent accuracy for the prediction set was 98.0%. The high predictive power for the prediction set shows the ability to indicate the cultivar of an unknown sample based on its fatty-acid chromatographic fingerprint.

The principles of causality and unitarity are studied within rational nonlinear electrodynamics proposed earlier. We investigate dyonic and magnetized black holes and show that in the self-dual case, when the electric charge equals the magnetic charge, corrections to Coulomb's law and Reissner-Nordstrom solutions are absent. In the case of the magnetic black hole, the Hawking temperature, the heat capacity and the Helmholtz free energy are calculated. It is shown that there are second-order phase transitions and it was demonstrated that at some range of parameters the black holes are stable.

Integrated photonic devices operating via optical nonlinearities offer a powerful solution for all-optical information processing, yielding processing speeds that are well beyond that of electronic processing as well as providing the added benefits of compact footprint, high stability, high scalability, and small power consumption. The increasing demand for high-performance nonlinear integrated photonic devices has facilitated the hybrid integration of novel materials to address the limitations of existing integrated photonic platforms, such as strong nonlinear optical absorption or an inadequate optical nonlinearity. Recently, graphene oxide (GO), with its large optical nonlinearity, high flexibility in altering its properties, and facile fabrication processes, has attracted significant attention, enabling many hybrid nonlinear integrated photonic devices with improved performance and novel capabilities. This paper reviews the applications of GO to nonlinear integrated photonics. First, an overview of GO’s optical properties and the fabrication technologies needed for its on-chip integration is provided. Next, the state-of-the-art GO nonlinear integrated photonic devices are reviewed, together with comparisons of the nonlinear optical performance of different integrated platforms incorporating GO. Finally, the challenges and perspectives of this field are discussed.

We review some new approaches to the description of the evolution of states of many-particle quantum systems by means of the correlation operators. Using the de nition of marginal correlation operators within the framework of dynamics of correlations governed by the von Neumann hierarchy, we establish that a sequence of such operators is governed by the nonlinear quantum BBGKY hierarchy. The constructed nonperturbative solution of the Cauchy problem to this hierarchy of nonlinear evolution equations describes the processes of the creation and the propagation of correlations in many-particle quantum systems. Moreover, we consider the problem of the rigorous description of collective behavior of many-particle quantum systems by means of a one-particle (marginal) correlation operator that is a solution of the generalized quantum kinetic equation with initial correlations, in particular, correlations characterizing the condensed states of systems.

In this work, fluorinated graphene nanoscrolls (FGN) were synthesized via facile chemical methods under simple and mild conditions. Interestingly, the formation of the featured FGN was significantly solvent sensitive. Experimental results indicated that in the presence of aprotic solvent, for example, N,N dimethylformamide (DMF), the reaction system inclined to form the interesting FGN nanostructures. The structure and morphology of the prepared FGN were detailed characterized by atomic force microscopy (AFM), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray diffraction (XRD) etc. The obtained FGN was used as a cathode material for primary lithium ion batteries with superior discharge specific capacity (eg. 979.3 mAhg-1), stable discharge platform and high energy density (eg. 2287.9 Wh kg-1), which fosters it a high density, low cost and durable candidate for cathode material for lithium ion batteries..

It is known that the class of p-normed spaces (0 < p ≤ 1) is an important generalization of usual normed spaces with rich topological and geometrical structure, but the most of tools and general principles in nature with nonlinearity have not been developed yet, thus the main goal of this paper is to develop tools for nonlinear analysis under the framework of p-vector spaces. In particular, we first develop the general fixed point theorems which provide solutions to answer Schauder conjecture since 1930’s in the affirmative for p-vector spaces when p = 1 (which is just general topological vector spaces); then the one best approximation result for upper semi-continuous mappings is given, which is used as a powerful tool to establish fixed points for non-self set-valued mappings with either inward or outward set conditions; and finally we establish comprehensive existence results of solutions for Birkhoff-Kellogg Problems, and the general principle of nonlinear alternative by including Leray-Schauder alternative and related results. The results given in this paper not only include the corresponding results in the existing literature as special cases, but also expected to be useful tools for the study of nonlinear problems arising from theory to practice.

The Thermodynamic Formalism provides a rigorous mathematical framework to study quantitative and qualitative aspects of dynamical systems. At its core there is a variational principle and corresponding, in its simplest form, to the Maximum Entropy principle, used as a statistical inference procedure to represent, by specific probability measures (Gibbs measures), the collective behaviour of complex systems. This framework has found applications in different domains of scienThe Thermodynamic Formalism provides a rigorous mathematical framework to study quantitative and qualitative aspects of dynamical systems. At its core there is a variational principle and corresponding, in its simplest form, to the Maximum Entropy principle, used as a statistical inference procedure to represent, by specific probability measures (Gibbs measures), the collective behaviour of complex systems. This framework has found applications in different domains of science, in particular, has been fruitful and influential in neurosciences. In this article, we review how the Thermodynamic Formalism can be exploited in the field of theoretical neuroscience, as a conceptual and operational tool, to link the dynamics of interacting neurons and the statistics of action potentials from either experimental data or mathematical models. We comment on perspectives and open problems in theoretical neuroscience that could be addressed within this formalism.ce, in particular, has been fruitful and influential in neurosciences. In this article, we review how the Thermodynamic Formalism can be exploited in the field of theoretical neuroscience, as a conceptual and operational tool, to link the dynamics of interacting neurons and the statistics of action potentials from either experimental data or mathematical models. We comment on perspectives and open problems in theoretical neuroscience that could be addressed within this formalism.

Recently, most countries suffering from global warming due to the waste gases coming out of the combustion engines used to generate electric power by traditional methods. Therefore, many countries are currently trying to find alternative solutions to this problem by using renewable energies such as solar energy, wind energy, and energy generated from the waves of the ocean and sea to overcome pollution problems. The waves of the seas and oceans have enormous and largely untapped energy, so this work presents an efficient way to use the energy of sea waves to generate electricity. And also, trying to be a way to produce electricity from wave energy in the future. The best suitable places along the shores of Jizan city were inspected to install the buoy system to revenue advantage of the wave supreme height to achieve the height amount of electrical energy. A mathematical model was made to analyze the wave energy and convert it into energy extracted by mechanical force. The mathematical analyzes used the data collected from satellite maps of the numerous severe waves in the Red sea of the Jazan area, and the data published in previous research along that area. It was found that the beach of the Al Shuqaiq area is the greatest for installing the buoy and obtaining the highest electrical energy due to the presence of the highest wave intensity, followed by the beach of the Baysh and Al Morgan area. Also, one of the objectives of this research is to study the design of a device powered by a buoy to use the waves of the Red Sea to generate electric power. The influence of the buoy system design parameters such as the buoy diameter, length of the cylinder, and the length of the connecting rod on the electrical energy generation from wave energy was investigated. The current device is designed with a gearbox to produce continuous power with a single electric generator. A floating mooring device uses the rise and fall of bulges to convert sea wave energy into electrical energy. The device consists of a float, arm, two wheels of different diameters, a gear set, and an electric generator. The effect of the design of several factors on the performance of the device for converting the sea waves energy into electrical energy, including the length of the buoy arm, the wave height by changing the cam diameter, and the conversion ratios between the gear set, to optimize the output power of the wave energy.

This study presents the substantiation, development, and analysis of a technique for planning the autonomous vehicle (AV) motion reference parameters. The trajectory plan, speed and acceleration distributions, including other AV's kinematic parameters, are determined using sequential optimization. The study objectives are based on an analysis of the fundamental problems of AV motion planning summarized in this area's latest publications. The proposed approach combines the basic principles of the finite element method (FEM) and nonlinear optimization with nonlinear constraints. First, the generalization on representing an investigated function by finite elements (FE) is briefly described. A one-dimension FE with two nodes and three degrees of freedom (DOF) in a node was chosen as the basic one, corresponding to the 5th-degree polynomial. Next, a method for determining the motion trajectory is presented. The following are considered: formation of a restricted space for the AV's allowable maneuvering, the geometry of motion trajectory and its relation with vehicle steerability parameters, cost functions and their influences on the desirable trajectory's nature, compliance of nonlinear restrictions of the node parameters with the motion area boundaries. At the second stage, a technique for optimizing AV speed and acceleration redistribution is presented. The model considers possible combinations of cost functions, conditions of limiting the kinematic parameters with the tire slip critical speed, maximum speed level, maximum longitudinal acceleration, and critical lateral acceleration. In the simulation section, several variants of trajectories were searched and compared. Several versions of distributing the longitudinal speed and acceleration curves are determined, and their comparative analysis is fulfilled. At the end of the paper, the advantages and drawbacks of the proposed technique are noted. The conclusion is made regarding the options for improving the method in further studies.

This dissertation is a rigorous study of ecology and macrocellular biology as a subfield of abstract algebra. We begin with the creation of an axiomatic paradigm, then move onto constructing a universal genetic code of biology. We use this to define increasingly complex algebraic structures (ecosystem, evolving populations, etc.). We prove a variety of theorems regarding to the members of the previous mathematical constructs, notably the following three: 1. There is one unique phenotypic representation of each organism. For example, if you subdivide any piece of genetic code into its phenotypic components, then two identical organisms have identical decomposed DNA 2. There are a finite number of indivisible phenotypic traits. 3. The three sophioid-definitions are equivalent: (a) dynamical evolutionary enlargement of the medial temporal lobe and frontal lobe, (b) reliance upon intelligence, (c) the existence of an intellectually- or socially-hierarchical society. Much has yet to be done on this work, but as a first draft, it stands as a jumping point for future exploits; I am working on an entirely revised second draft.

Any effort to combat corruption can benefit from an examination of past and projected worldwide trends. In this paper, we forecast the level of corruption in countries by integrating an artificial neural network modeling and time series analysis. The data were obtained from 113 countries from 2007 to 2017. The study is carried out at two levels: (a) global level where all countries are considered as a monolithic group; and (b) cluster level, where countries are placed into groups based on their development-related attributes. For each cluster, we use the findings from our previous study on the cluster analysis of global corruption using machine learning methods that identified the four most influential corruption factors, and we use those as independent variables. Then, using the identified influential factors, we forecast the level of corruption in each cluster using a nonlinear autoregressive recurrent neural network with exogenous inputs (NARX), an artificial neural network technique. The NARX models were developed for each cluster, with the objective function in terms of the Corruption Perceptions Index (CPI). For each model, the optimal neural network is determined by finetuning the hyperparameters. The analysis was repeated for all countries as a single group. The accuracy of the models is assessed by comparing the mean square errors (MSE) of the time series models. The results suggest that the NARX artificial neural network technique yields reliable future values of CPI globally or for each cluster of countries. This can assist policymakers and organizations in assessing the expected efficacies of their current or future corruption control policies from a global perspective as well as for groups of countries.

Most systems that are the subject of control engineering studies have some non-linearity. An example of this is the horizontal cylindrical tank, commonly used in process industries. To deal with cases like this, several control theories have been developed over time, each one presenting better results in certain systems. This work presents an alternative for the control of nonlinear systems, without necessary modeling or previous information about the system, based on a new optimization law for the artificial neural network training in real time.

Complex diseases such as cancer are caused by changes in the Gene Regulatory Networks. Systems that model the complex dynamics of these networks along with adapting to real gene expression data are closer to reality and can help understand the creation and treatment of cancer. In this paper, for the first time, modelling of gene regulatory networks is performed using delayed nonlinear variable order fractional systems in the state space by a new tool called GENAVOS. This tool uses gene expression time series data to identify and optimize system parameters. This software has several tools for analyzing system dynamics. The results show that the nonlinear variable order fractional systems have very good flexibility in adapting to real data. We found that regulatory networks in cancer cells actually have a larger delay parameter than in normal cells. It is also possible to create chaos, periodic and quasi-periodic oscillations by changing the delay, degradation and synthesis rates. Our findings indicate a profound effect of time-varying order on these networks, which may be related to a type of cellular memory due to epigenetic and environmental factors. We showed that by changing the delay parameter and the variable order function for a normal cell system, its behavior changes and becomes quite similar to the behavior of a cancer cell. This work also confirms the effective role of the miR-17-92 cluster in the cancer cell cycle. GENAVOS is available at https://github.com/hanif-y/GENAVOS with its user guide and MATLAB codes.

In this work, we treat a prediction problem via the conditional hazard function of a scalar response variable Y given a functional random variable X by using the local linear technique. The main purpose of this paper is to investigate the asymptotic normality of the nonparametric estimator of the conditional hazard function, under some general conditions. A simulation study, conducted to assess finite sample behavior, demonstrates the superiority of our method than the standard kernel method

The Lamiaceae belong to the species-richest families of flowering plants and harbor many species used as herbs or for medicinal applications, such as Basils or Mints. Evolution of this group has been driven by chemical speciation, mainly of Volatile Organic Compounds (VOCs). The commercial use of these plants is characterized by a large extent of adulteration and surrogation. To authenticate and discern the species, is, thus, relevant for consumer safety, but usually requires cumbersome analytics, such as Gas Chromatography, often to be coupled with Mass Spectroscopy. We demon-strate here that quartz-crystal microbalance (QCM)-based electronic noses provide a very cost-efficient alternative, allowing for a fast, automated discrimination of scents emitted from leaves of different plants. To explore the range of this strategy, we used leaf material from four genera of Lamiaceae along with Lemongrass as similarly scented, but non-related outgroup. In order to unambiguously differentiate the scents from the different plants, the output of the 6 different SURMOF/QCM sensors was analyzed using machine learning (ML) methods, together with a thorough statistical analysis. The exposure and purging datasets (4 cycles) obtained from a QCM-based, low-cost homemade portable e-Nose were analyzed with Linear Discriminant Analysis (LDA) classification model. Prediction accuracies with repeating test measurements reached values of up to 90%. We show that it is not only possible to discern and identify plants on the genus level, but even to discriminate closely related sister clades within a genus (Basil), demonstrating that e-Noses are a powerful technology to safeguard consumer safety against the challenges of globalized trade.

Remote sensing is one of the modern methods that have significantly developed over the last two decades and nowadays provides a new means for forest monitoring. High spatial and temporal resolutions are demanded for accurate and timely monitoring of forests. In this study multi-spectral Unmanned Aerial Vehicle (UAV) images were used to estimate canopy parameters (definition of crown extent, top and height as well as photosynthetic pigment contents). The UAV images in Green, Red, Red-Edge and NIR bands were acquired by Parrot Sequoia camera over selected sites in two small catchments (Czech Republic) covered dominantly by Norway spruce monocultures. Individual tree extents, together with tree tops and heights, were derived from the Canopy Height Model (CHM). In addition, the following were tested i) to what extent can the linear relationship be established between selected vegetation indexes (NDVI and NDVIred edge) derived for individual trees and the corresponding ground truth (e.g., biochemically assessed needle photosynthetic pigment contents), and ii) whether needle age selection as a ground truth and crown light conditions affect the validity of linear models. The results of the conducted statistical analysis show that the two vegetation indexes (NDVI and NDVIred edge) tested here have a potential to assess photosynthetic pigments in Norway spruce forests at a semi-quantitative level, however the needle-age selection as a ground truth was revealed to be a very important factor. The only usable results were obtained for linear models when using the 2nd year needle pigment contents as a ground truth. On the other hand, the illumination conditions of the crown proved to have very little effect on the model’s validity. No study was found to directly compare these results conducted on coniferous forest stands. This shows that there is a further need for studies dealing with a quantitative estimation of the biochemical variables of nature coniferous forests when employing spectral data acquired by the UAV platform at a very high spatial resolution.

This paper is intended at highlighting the main mechanical parameters controlling the behavior of the so-called "acceleration-sensitive" Non-Structural Components (NSCs). In the first part a short review of the current state of knowledge and the critical issues related to the prediction of the seismic response of NSCs is reported. Then, the paper presents the results of a numerical parametric analysis intended to capture the key features of the dynamic response of a two-degree-of-freedom (2DOF) system which is supposed to be representative of both the main structure and the "non-structural" component (NSC). Particularly, it allows to simulate the coupled behaviour of both main structure and NSC and evaluating their response. The main parameters controlling the dynamic response of NSCs emerge from this study, which could pave the way towards formulating more mechanically consistent relationships for evaluating the maximum accelerations induced by seismic shakings on NSCs.

The present article addresses the long-standing problem of the polymer brush bilayers under stationary shear flow at non-linear response regime where the system gets a non-Newtonian fluid. The main idea behind this research would be the fact that the immense lubricity of the polymer brush bilayers originates from a global restructuring that takes place at large shear rates. It is shown here that physical quantities like, stress tensor, viscosity tensor, the friction coefficient and the chain extensions could become dependent on the shear rate at non-Newtonian regime. Apparently, the sub-linear scaling of the physical quantities at large shear rates is solely due to the fact that the chains stretch in the shear direction.

Since December 2019, the coronavirus disease (COVID-19) has rapidly spread worldwide. The Mexican government has implemented public safety measures to minimize the spread of the virus. In this paper, the authors use statistical models in two stages to estimate the total number of coronavirus (COVID-19) cases per day at the state and national level in Mexico. Two types of models are proposed: first, a polynomial model of the growth for the first part of the outbreak until the inflection point of the pandemic curve and then a second nonlinear growth model is used to estimate the middle and the end of the outbreak. Model selection will be performed using Vuong’s test. The proposed models show overall fit similar to predictive models (e.g. time series, and machine learning); however, the interpretation of parameters is less complex for decision-makers and the residuals follow the expected distribution when fitting the models without autocorrelation being an issue.

We compare Chiral Perturbation Theory (ChPT) and the Linear Sigma Model (LSM) as realizations of low energy QCD for light mesons in a chirally imbalanced medium. The relations between the low-energy constants of the Chiral Lagrangian and the corresponding constants of the Linear Sigma Model are established as well as the expressions for the decay constant of $\pi $-meson in the medium and for the mass of the $a_0$. In the large $N_c$ count taken from QCD the correspondence of ChPT and LSM is remarkably good and give a solid ground for search of chiral imbalance manifestation in pion physics. A possible experimental detection of chiral imbalance (and therefore a phase with Local Parity Breaking) is outlined in the charged pion decays inside the fireball.

In this study, we describe quark confinement in terms of linear interaction potentials and solve the problem of the net spin of a proton. The three quarks in a proton are assumed to revolve around a common center, and their masses are determined assuming they are Dirac particles. On the basis of these assumptions, the magnetic moment of a proton can be derived. Moreover, the rotation of the quarks is considered, in which an electrical current induces a magnetic field. Thus, the scalar product of the magnetic moment and field describes the linear interaction potential between the quarks, and the mass of the proton can be obtained. The proton mass predicted by this physical model is consistent with experimental values, and no numerical or fitting calculations are required. Furthermore, using the newly derived spins and angular momentum of the three quarks, we derived the net spin of a proton. Additionally, we predicted the mass of a pi-meson from the same model, which agrees with the experimental values.

The overrun of transient power quality index caused by the large-capacity electric arc furnace (EAF) has become a prominent problem affecting the safe and stable operation of the power system. (1) In this paper, the relationship between arc furnace volt-age and current is derived based on the different stages of arc combustion, and the random variation of chaotic phenomenon of the arc voltage are simulated. Established an EAF model suitable for the study of transient power quality problems. (2) Take 50t AC EAF as an example to analyze the reactive power impact and the influence on the point of common coupling (PCC) voltage caused by the three-phase short circuit of the electrode. The results show that the experimental results are consistent with the theoretical analysis, verifying the correctness and effectiveness of the model. (3) When the three-phase short-circuit occurs, the reactive power impact is nearly 6 times that of normal operation, the short-circuit current is 2.66 times that of normal operation, and the effective value of the PCC voltage has dropped by 40.37%, which provides a theoretical basis for real-time compensation of impulsive reactive power and improvement of the transient power quality of the EAF.

Non-intrusive load monitoring (NILM) is a core technology for demand response (DR) and energy conservation services. Traditional NILM methods are rarely combined with practical applications, and most studies aim to decompose the whole loads in a household, which leads to low identification accuracy. In this paper, an NILM approach based on multi-feature integrated classification (MFIC) is explored, which combines some non-electrical features such as ON/OFF duration, usage frequency of appliances, and usage period to improve load differentiability. The implementation of MFIC algorithm is consistent with traditional event-based method. The uniqueness of our algorithm is that it designs an event detector based on steady-state segmentation and a linear discriminant classifier group based on multi-feature global similarity. Simulation results using an open-access dataset demonstrate the effectiveness and high accuracy of MFIC algorithm, with the state-of-the-art NILM methods as benchmarks.

Soil quality assessment based on crop yields and identification of key indicators of it can be used for better management of agricultural production. In the current research, the weighted additive soil quality index (SQIw), factor analysis (FA) and multiple linear regression (MLR) method are used to assess the soil quality of rainfed winter wheat fields with two soil orders on 53.20 km2 of agricultural land in western Iran. A total of 18 soil quality indicators were determined for 100 soil samples (0-20 cm depth) from two soil orders (Inceptisols and Entisols). The soil properties measured were: pH, soil texture, organic carbon (OC), cation exchange capacity (CEC), electrical conductivity (EC), soil microbial respiration (SMR), carbonate calcium equivalent (CCE), soil porosity (SP), bulk density (BD), exchangeable sodium percentage (ESP), mean weight diameter (MWD), available potassium (AK), total nitrogen (TN), available phosphorus (AP), available Fe (AFe), available Zn (AZn), available Mn (AMn), and available Cu (ACu). Mean wheat grain yield for the two years for all of the 100 sampling sites was also gathered. The SQIw was calculated using two weighting methods (FA and MLR) and maps were created using a digital soil mapping framework. The soil indicators taken in the minimum data set (MDS) were AK, clay, CEC, AP, SMR, and sand. The correlation between the MLR weighting technique (SQI-M) and the rainfed wheat yield (r=0.62) was slightly larger than that the correlation of yield with the FA weighted technique (SQI-F) (r=0.58). Results showed that the means of both SQI-M and SQI-F and rainfed wheat yield for Inceptisols were higher than for Entisols although these differences were not statistically significant. Both SQI-M and SQI-F showed that areas with Entisols had lower proportions of good soil quality grades (Grade I and II), and higher proportions of poor soil quality grades (Grade IV and V) compared to Inceptisols. Based on these results, soil type must be considered for soil quality assessment in future studies to maintain and enhance soil quality and sustainable production. The overall soil quality of the study region was of poor and moderate grades. To improve soil quality, it is therefore recommended that effective practices such as the implementation of scientific integrated nutrient management involving the combined use of organic and inorganic fertilizers in rainfed wheat fields be promoted.

This work presents a control scheme to control the grid-connected single-phase photovoltaic (PV) system. The considered system has four 250W solar panels, a non-inverting buck-boost DC-DC converter, and DC-AC inverter with LCL filter. The control system aims to track and operate at the maximum power point (MPP) of PV panels, regulate the voltage of DC link, and supply the grid with a unity power factor. To well achieve these goals, the proposed control system consists of three parts, that are MPP tracking controller module with a fuzzy-based modified incremental conductance (INC) algorithm, a DC-link voltage regulator with a hybrid fuzzy proportional-integral (PI) controller, and a Current Controller module using the linear quadratic regulator (LQR) for grid-connected power. Based on fuzzy control and LQR, this work introduces a full control solution for grid-connected single-phase PV systems. The key novelty of this research is to analyze and prove that the newly proposed method is more successful in numerous aspects by comparing and evaluating the previous and present control methods. The designed control system settles quickly, which is critical for output stability. In addition, as compared to backstepping approach used in our past study, the LQR technique is more resistant to sudden changes and disturbances. Furthermore, backstepping method produces the larger overshoot, which has a detrimental impact on efficiency. Simulation findings under various weather conditions were compared to theoretical ones to indicate that the system can deal with variations in weather parameters.

In this paper, we proposed a new model of non-linear electrodynamics with parameter. Firstly, we study the weak limit approximation and by using the Gauss Bonnet theorem, we obtain the deflection angle of photon from magnetized black hole and effect of bnon-linear electrodynamics. In doing so, we find the corresponding optical metric after that we calculate the Gaussian curvature which is used in Gauss Bonnet theorem. Then we show the deflection angle in the leading order terms. We also analyzed that our results reduces into Maxwell's electrodynamics and RN solution with the reduction of parameters. Moreover, we also investigate the graphical behavior of deflection angle w.r.t correction parameter, black hole charge and impact parameter.

Abstract: Safety issues related to the electrification of more electric aircraft (MEA) need to be addressed because of the increasing complexity of aircraft electrical power systems and the growing number of safety-critical sub-systems that need to be powered. Managing the energy storage systems and the flexibility in the load-side plays an important role in preserving the system’s safety when facing an energy shortage. This paper presents a system-level centralized operation management strategy based on model predictive control (MPC) for MEA to schedule battery systems and exploit flexibility in the demand-side while satisfying time-varying operational requirements. The proposed online control strategy aims to maintain energy storage (ES) and prolong the battery life cycle, while minimizing load shedding, with fewer switching activities to improve devices lifetime and to avoid unnecessary transients. Using a mixed-integer linear programming (MILP) formulation, different objective functions are proposed to realize the control targets, with soft constraints improving the robustness of the model. Besides, an evaluation framework is proposed to analyze the effects of various objective functions and the prediction horizon on system performance, which provides the designers and users of MEA and other complex systems with new insights into operation management problem formulation.

Management of demand and capacity for airport operation is important. The effect of capacity setting on slot adjustment, maximum adjustment and flight delay has been extensively investigated and discussed in previous slot adjustment models. But its effect on characteristics of flight waves has not been studied deeply. At present, in order to resolve the problem that Linear Integer Programming (LIP) is limited in slot allocation due to its fast dimension growth and large memory consumption, the general practice is to optimize the slot application according to data-splitting technology. However, the relationship among data splitting method, capacity setting and characteristics of slot wave has not been investigated in detail, which limits the application of LIP in slot allocation. Through the detailed analysis and testing, we found that the waveform and amplitude of slot wave can be controlled and designed by appropriate virtual capacity settings, while the number of capacity constraints and the computing time is reduced by adopting appropriate data feeding method. Our research also provides clues for further research on the construction of the flight waves for airlines operating at specific airports in order to establish direct or indirect connectivity, and increase hit rate by using our approaches.

In this paper, we define new kind of Daehee numbers, the degenerate Daehee numbers of the third kind, using degenerate log function as generating function. We obtain some identities for the degenerate Daehee numbers of the third kind associated with the Daehee, degenerate Daehee and degenerate Daehee numbers of the second kind. In addition, we derive a differential equation associated with the degenerate log function. We deduce some identities from the differential equation.

This paper presents a novel method of restoring the electron beam (EB) measurements that are degraded by linear motion blur. This is based on a Fuzzy Inference System (FIS) and Wiener inverse filter, together providing autonomy, reliability, flexibility and real-time execution. This system is capable of restoring highly degraded signals without requiring the exact knowledge of EB probe size. The FIS is formed of three inputs, eight fuzzy rules and one output. The FIS is responsible to monitor the restoration results, grade their validity and choose the one that yields to a better grade. These grades are produced autonomously by analyzing results of Wiener inverse filter. To benchmark the performance of the system, ground truth signals obtained using an 18 um wire probe are compared with the restorations. Main aims are therefore a) Provide unsupervised deblurring for device independent EB measurement; b) Improve the reliability of the process; c) Apply deblurring without knowing the probe size. These, further facilitates the deployment and manufacturing of EB probes and probe independent and accurate EB characterization. It also makes restoration of previously collected EB measurements easier, where the probe sizes are not known or recorded.