This paper addresses the modeling of the iron ore direct reduction process, a process likely to reduce CO₂ emissions from the steel industry. The shaft furnace is divided into three sections (reduction, transition, and cooling), and the model is two-dimensional (cylindrical geometry for the upper sections and conical geometry for the lower one), to correctly describe the lateral gas feed and cooling gas outlet. This model relies on a detailed description of the main physical–chemical and thermal phenomena, using a multi-scale approach. The moving bed is assumed to be comprised of pellets of grains and crystallites. We also take into account eight heterogeneous and two homogeneous chemical reactions. The local mass, energy, and momentum balances are numerically solved, using the finite volume method. This model was successfully validated by simulating the shaft furnaces of two direct reduction plants of different capacities. The calculated results reveal the detailed interior behavior of the shaft furnace operation. Eight different zones can be distinguished, according to their predominant thermal and reaction characteristics. An important finding is the presence of a central zone of lesser temperature and conversion.

The recent pandemic has greatly stressed supply chains, treatment modalities, and medical resources. Cold atmospheric plasma (CAP) has been used for a wide range of applications in biomedical engineering due to its many components including electrons, charged particles, reactive oxygen species (ROS), reactive nitrogen species (RNS), free radicals, ultraviolet (UV) photons, molecules, electromagnetic fields, physical forces, and electric fields. In this manuscript, we develop CAP devices for COVID-19. Our manuscript indicates the advantages of highlydeployable CAP devices for both sanitation and treatment, without the need for supply chains of special consumables such as hand sanitizers and the like. We hope that this timely research will help engage the broader community of engineers that wish to help the medical community with this pandemic and to prevent and treat future outbreaks.

In this paper, an original approach allowing the determination of the iron losses in the electromagnetic devices is presented. This new approach exploits the Loss Surface (LS) hysteresis model and the magnetic flux density waveforms resulting from a generalized nonlinear adaptive magnetic equivalent circuit (MEC) using a mesh-based formulation in two-dimensional (2-D) or quasi three-dimensional (3-D). The model coupling has been applied to a 18-slots/16-poles radial-flux interior permanent-magnet (PM) synchronous machine (PMSM) dedicated to automotive applications, mainly for electric/hybrid/fuel cell vehicles (EVs/HEVs/FCVs). The obtained results have been compared with those made retrospectively in the 2-D transient finite-element (FE) Flux. The influence of the MEC discretization on the iron loss calculation and the electromagnetic performances has been analyzed. The computation time is divided by 3/2 with an error less than 7 %.

The present investigation highlights the synthesis of polyaniline (PANI) coated graphene oxide doped with SrTiO3 nanocube nanocomposites through facile in-situ oxidative polymerization method for the efficient removal of carcinogenic dyes, namely, the cationic dye methylene blue (MB) and the anionic dye methyl orange (MO). The synthesised nanocomposites were characterised by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The adsorption efficiencies of graphene oxide (GO), PANI homopolymer and SrTiO3 nanocubes-doped nanocomposites were assessed by monitoring the adsorption of methylene blue and methyl orange dyes from aqueous solution. The adsorption efficiency of nanocomposites doped with SrTiO3 nanocubes were found to be of higher magnitude as compared with undoped nanocomposite. Moreover, the nanocomposite with 2 wt% SrTiO3 with respect to graphene oxide demonstrated excellent adsorption behaviour with 99% and 91% removal of MB and MO respectively, in a very short duration of time.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Reducing emissions from the iron and steel industry is essential to achieve the Paris climate goals. A new system to reduce the carbon footprint of steel production is proposed in this article by coupling hydrogen direct reduction of iron ore (H-DRI) and natural gas pyrolysis on liquid metal surface inside a bubble column reactor. If grid electricity from EU is used, the emissions would be 435 kg CO₂/tls without considering methane leakage from the extraction, storage and transport of natural gas. Solid carbon, produced as a by-product of natural gas decomposition, finds applications in many industrial sectors, including as a replacement for coal in coke ovens. Specific energy consumption (SEC) of the proposed system is approximately 6.3 MWh per ton of liquid steel(tls). It is higher than other competing technologies, 3.48 MWh/tls for water electrolysis based DRI, and, 4.3-4.5 MWh/tls for natural gas based DRI and blast furnace-basic oxygen furnace (BF-BOF) respectively. Utilization of large quantities of natural gas, where the carbon remains unused, is the major reason for high SEC. Preliminary analysis of the system revealed that it has the potential to compete with existing technologies to produce CO₂ free steel, if renewable electricity is used. Further studies on the kinetics of the bubble column reactor, H-DRI shaft furnace, design and sizing of components, along with building of industrial prototypes are required to improve the understanding of the system performance.

In this paper the influence of austempering temperature and salt bath agitation on the final microstructure and mechanical properties of the ferritic ductile iron were studied. 17 samples had been subjected to different heat treatment parameters. Different microstructures were recorded upon the completion of the tests. From the obtained micro images, it is obvious that both the austempering temperature and salt bath agitation affect the final microstructure of the austempered ductile iron. Lower austempering temperatures and salt bath agitation produce more ausferrite in the microstructure, hence the harder and tougher phases are present. This was confirmed with hardness and toughness test of the 17 heat-treated samples. Lower austempering temperatures give more ausferrite phase and therefore higher hardness, but hardness decreases with increasing austempering temperatures. Toughness rises with rising austempering temperatures, but drops significantly with temperatures above 395°C because of the final microstructure.

In the present work, the state of the art of the most common additive manufacturing (AM) technologies used for the manufacturing of complex shape structures of graphene-based ceramic nanocomposites, ceramic and graphene-based parts is explained. A brief overview of the AM processes for ceramic, which are grouped by the type of feedstock used in each technology, is presented. The main technical factors that affect the quality of the final product were reviewed. The AM processes used for 3D printing of graphene-based materials are described in more detail; moreover, some studies in a wide range of applications related to these AM techniques are cited. Furthermore, different feedstock formulations and their corresponding rheological behaviour were explained. Additionally, the most important works about the fabrication of composites using graphene-based ceramic pastes by Direct Ink Writing (DIW) are disclosed in detail and illustrated with representative examples. Various examples of the most relevant approaches for the manufacturing of graphene-based ceramic nanocomposites by DIW are provided.

Reactive NO_x is one of the major air pollutants, which also plays a key role as greenhouse gas. Many research efforts have been devoted to not only detection of NO_x in air but also abatement of NO_x emission. The aim of this mini review is to provide a panoramic snapshot of the electrochemical analysis methods for the emission and detection of NO_x in atmosphere, with special emphasis on NO_x sensor. The electrochemical detecting mechanism and materials for fabricating electrochemical gas sensors are discussed and the prospects and challenges in this area are also evaluated. This work will serve as a useful source to inform the interested audience of the latest developments and applications in the field of NO_x emission and electrochemical detection.

It is important to realize the transformation behavior of wüstite because it greatly affects the final structure of the oxide layer and the surface quality of the steel products. In the present study, the transformation behaviors of the wüstite layer are examined under nearly-oxygen-free conditions, to simulate the cooling processes after the hot rolled strip is coiled. As the single phase wüstite was prepared at 950˚C, the 460˚C transformed oxide layer was composed of a mixture of iron and magnetite formed through eutectoid reactions. For the 750˚C-fabricated wüstite, only magnetite was observed after transformation, without iron precipitates and residual wüstite. It is speculated that the unusual transformation behavior of the low-temperature-made wüstite results from the pseudo-structural intermediate phase transformation between wüstite and magnetite. This pseudo-structure is a pre-transformed wüstite and of various concentration of ferrous ion, which is determined by the fabrication conditions. During the hot strip mill process, the so-called wet scale, wüstite, is produced continuously from finish mill to laminar flow sections and ended at 570˚C. Consequently, the final eutectoid transformation below 570˚C is dominantly controlled by the surface temperature ranged from 750˚C to 950˚C for low carbon steel.

One consequence of the global technological advancement in conventional metallurgy is the fast depletion rate of valuable minerals, which are also becoming increasingly difficult to find in pure and economically viable forms. This has spurred more interest in technologies that investigate ability of different microorganisms to mobilize valuable metals from their ores via diverse metabolic processes. This study was carried out therefore to isolate, identify and characterize iron solubilizing bacteria from Iron stones of Agbaja iron ore mining site of Kogi State, Nigeria. Crushed samples in the range of 0.25µm and 0.75µm particle sizes were cultured in a modified 9k media to facilitate bacterial growth and pure cultures were then isolated and sub-cultured for further bioleaching studies. Morphological and biochemical analysis suggests that some of the bacteria identified are members of Acidithiobacillus spp, Pseudomonas spp, and Leptospirillum spp. Studies conducted on pure cultures and mixed consortium of the identified organisms shows that a mixture of the three organisms leached iron ore to about 96.16%. Also results of growth pattern due to bacteria countafter 24-72hours of incubation ranged between 0.1×10³ cfu/ml and 12.3 ×10³ cfu/ml for Acidithiobacillus spp. The need to explore the molecular characteristics of these organisms with a view to generating more information on the quality/quantity of their DNA for future cloning activities was also investigated in this work. DNA was extracted using zymo fungal/bacterial extraction mini prep kit ^TM (cat #6001) and subsequently subjected to 1% agarose gel electrophoresis. Visible bands were obtained with Alpha Innotech Gel Documentation Machine. DNA amplification was carried out using a pettier based thermo cycler PCR machine and electrophoresed on 1.5% agarose gel. Results of the PCR shows a visible band corresponding to 1.5kbp using this primer 27F (5¹-GAGTTTGATCCTGGCTCAG-3¹) and 1492R (5^1-GGTTACCTTGTTACGACT-3¹). DNA purity check shows two of the bacteria possess very good qualities for sequencing for further molecular analysis.

The microstructural evolution, thermodynamics and kinetics of Mo-21%Tm₂O₃ (mass fraction, %) powder mixtures during ball milling were investigated using X-ray diffraction and transmission electron microscopy. Ball milling induced Tm₂O₃ to be decomposed and then dissolved into Mo crystal. The supersaturated nanocrystalline solid solution of Mo (Tm, O) was obtained after 96 h of ball milling. The elements of Mo, Tm and O were distributed uniformly in the ball-milled particles. Based on the semi-experimental theory of Miedema, a thermodynamic model was developed to calculate the driving force of phase evolution. There was no chemical driving force to form a crystal solid solution of Tm atoms in Mo crystal or an amorphous phase because the Gibbs free energy for both processes was higher than zero. For Mo-21%Tm₂O₃, it was mechanical work, not negative heat of mixing, that provided the driving force to form supersaturated nanocrystalline Mo (Tm, O) solid solution.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

Abstract: The aim of this study was to find out the incidence of anemia in pregnant women of Swat District; to analyze the iron variations and its dietary effects.Data were collected during the periods of January – September 2016. The study of samples comprised of 250 pregnant women in the different trimester. Blood sample from each woman was collected and full blood count (FBC) was conducted through Mindray BC-3000 plus hem analyzer for all pregnant individuals. Confirmed anemic cases were then examined for IDA with serum ferritin, serum iron, total iron binding capacity (TIBC) through Randox kit and serum transferrin saturation was estimated by formula (serum ferritin saturation =serum iron ×100/TIBC). The total number of participants in the first trimester were 50, among them 26 women were suffer from iron deficiency anemia (IDA) with 52% weightage of prevalence rate, (mean Hb concentration 9.602 ± 0.87 g/dl). The rates of IDA were 63.3%; ( mean Hb concentration 8.48 ± 1.24 g/dl) and 54%; ( mean Hb concentration 9.18 ± 1.28 g/dl), among 150 and 50 participants in the second and third trimester, respectively. A significant correlation was found between serum ferritin and Hb, serum ferritin against MCV and serum ferritin against MCH. The high prevalence of anemia was found 78.2% in the age group from 26-30 followed by 78.2% in the age group 36-40 years compared to those of other age groups in the second trimester. In this study the prevalence of IDA in third trimester is lower compared to first and second trimester.

There is a marked momentum towards the use of clean hydrogen energy as an alternative for fossil fuels. Renewable energies such as solar and wind are being used to generate hydrogen from the water hydrolysis process. Indeed, this approach stores renewable energies in the form of combustible hydrogen for other energy uses. The other alternative that could be economically more cost-effective at the current technology stage is to explore the natural “Hydrogen System” where the natural hydrogen is generated and accumulated within the earth system, the same that stands for a “Petroleum System”. The Discovery of a large accumulation of relatively pure natural hydrogen (H2) in Mali has triggered the opportunity of searching for natural hydrogen accumulations in other countries. The generation of hydrogen from a circular depression in Mali and some other countries is linked to the presence of geologically very old iron-rich basement rocks. Solid-liquid redox reactions between iron-rich minerals and groundwater that split water are a possible source of H2 in deep basement rocks. It is believed that the hydrogen degassing may be detected by surface topographic circular to sub-circular shallow depressions. Chemical processes such as dissolution by hydrogen are considered to play the main role in the formation of the circular depressions through preferential vertical hydrogen migration channel. Archean iron-rich Yilgarn Craton that covers a vast area of Western Australia (WA) contains abundant iron-rich mafic-ultramafic rocks. The craton reveals many surficial circular depressions visible through satellite images. The area has abundant fault systems and is blanketed with Eocene sedimentary rocks containing high-quality reservoir rocks. All these characteristics seem to provide most of the required elements, such as hydrogen source, migration pathway, and reservoir rock for a “Hydrogen System” in this area.

Gray cast iron is one of the most important engineering materials that has many applications in various industries including automotive and machinery manufacturing due to its mechanical properties, wear resistance, machining potentials and low price. In this research effect of adding aluminum and silicon to composition of gray cast iron on microstructure and wear resistance was studied. Moreover, it was investigated the role of formation of Fe-Al-Si intermetallic compound in final properties of the alloy. For studying wear resistance of samples pin-on-disc method was carried out. The results showed that addition of aluminum to gray cast iron causes formation of ferrite matrix, which leads to a decrease in hardness value. Increasing silicon content up to 2 wt. % in cast iron with 4 wt. % aluminum intensifies the formation of ferrite matrix, while further increase to 3 wt. % causes emerging a Fe-Al-Si intermetallic phase. Improvement in hardness value was achieved by increasing silicon content from 3 wt. % to 4 wt. % due to the increased percentage of intermetallic phase. Effect of intermetallic phase on decreasing wear rate was showed by studying microstructure and hardness values, however the lowest wear resistance was observed in aluminum bearing cast iron containing 2 wt. % silicon.

Aquatic animals have unique physiological mechanisms to absorb and retain minerals from their diets and water. Research and development in the area of mineral nutrition of farmed fish and crustaceans have been relatively slow and major gaps exist in the knowledge of trace element requirements, physiological functions and bioavailability from feed ingredients. Quantitative dietary requirements have been reported for three macroelements (calcium, phosphorus and magnesium) and six trace minerals (zinc, iron, copper, manganese, iodine and selenium) for selected fish species. Mineral deficiency signs in fish include reduced bone mineralization, anorexia, lens cataracts (zinc), skeletal deformities (phosphorus, magnesium, zinc), fin erosion (copper, zinc), nephrocalcinosis (magnesium deficiency, selenium toxicity), thyroid hyperplasia (iodine), muscular dystrophy (selenium) and hypochromic microcytic anaemia (iron). An excessive intake of minerals from either diet or gill uptake causes toxicity and therefore a fine balance between mineral deficiency and toxicity is vital for aquatic organisms to maintain their homeostasis either through increased absorption or excretion. Release of minerals from uneaten or undigested feed and from urinary excretion can cause eutrophication of natural waters, which requires additional consideration in feed formulation. The current knowledge in mineral nutrition of fish is briefly reviewed.

Comminution is a very important and result-determining step in mineral processing. This is because further downstream processes in the beneficiation chain depend entirely on it. Comminution includes the blasting, crushing, and grinding of ore to liberate valuable mineral particles. It consumes most of the energy used in mineral processing plants with grinding using up to 50% of the provided energy. Tumbling mills are an old technology that is still commonly used for grinding. One of the most used tumbling mills is the ball mill. This paper reviews different types of grinding media that have been developed and improved over the years and their properties. Also reviewed are the effects of grinding media on various aspects such as energy consumption, mill efficiency, minerals liberation and grinding rate. A comparison of the grinding media is given together with the knowledge gaps that still need to be bridged to improve the quality and performance of grinding media used in ball mills. Despite various research conducted on ball mills, the grinding process is still a very energy inefficient process. This creates a great opportunity for further research to improve the process because just a slight improvement in the process efficiency significantly reduces the production costs and provides a lot of environmental benefits.

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

Erigeron floribundus (Asteraceae) is an herbaceous plant widely used in the Cameroonian traditional medicine to treat various diseases of microbial and non-microbial origin. In the present study we evaluated the in vitro biological activities displayed by the essential oil obtained from the aerial parts of E. floribundus, namely the antioxidant, antimicrobial and antiproliferative activities. Moreover, we investigated the inhibitory effects of E. floribundus essential oil on nicotinate mononucleotide adenylyltransferase (NadD), a promising new target for developing novel antibiotics, and Trypanosoma brucei, the protozoan parasite responsible for Human African trypanosomiasis. The essential oil composition was dominated by spathulenol (12.2%), caryophyllene oxide (12.4%) and limonene (8.8%). The E. floribundus oil showed a good activity against Staphylococcus aureus (IZD of 14 mm, MIC of 512 µg/mL). Interestingly, it inhibited the NadD enzyme from S. aureus (IC50 of 98 µg/mL), with no effects on mammalian orthologue enzymes. In addition, T. brucei proliferation was inhibited with IC50 values of 33.5 µg/mL with the essential oil and 5.6 µg/mL with the active component limonene. The essential oil exhibited strong cytotoxicity on HCT 116 colon carcinoma cells with an IC50 value of 14.89 µg/mL, and remarkable ferric reducing antioxidant power (TEAC= 411.9 μmol TE/g).

Mesoporous TiO2/reduced graphene oxide/Ag (TiO2/RGO/Ag) ternary nanocomposite with effective electrons transfer pathway is obtained by an electrostatic self-assembly method and photo-assisted treatment. Compared with bare mesoporous TiO2 (MT) and mesoporous TiO2/RGO (MTG), the ternary mesoporous TiO2/RGO/Ag (MTGA) nanocomposite exhibited superior photocatalytic performance for the degradation of MB under visible light, and the degradation rate reached 0.017 min-1, which was 3.4 times higher than that of MTG. It is proposed that Ag nanoparticles can form the local surface plasmon resonance (LSPR) to absorb the visible light and distract the electrons into MT, and RGO can accept the electrons from MT to accelerate the separation efficiency of carriers. The establishment of MTGA ternary nanocomposite make the three components act synergistic effect to enhance the photocatalytic performance.

Water borne pathogens present a threat to human health and their disinfection from water poses a challenge, prompting search for newer methods and newer materials. Disinfection of Gram-negative bacterium Escherichia coli and Gram-positive coccal bacterium Staphylococcus aureus in aqueous matrix was achieved within 60 and 90 minutes respectively at 35⁰C using solar-photocatalysis mediated by sonochemically synthesized Ag@ZnO core-shell nanoparticles. The efficiency of the process increased with increase in temperature and at 55⁰C the disinfection could be achieved in 45 and 60 min respectively for the two bacteria. A new ultrasound assisted chemical precipitation technique was used for the synthesis of Ag@ZnO core-shell nanoparticles. The characteristics of the synthesized material were established using physical techniques. The material remained stable even at 400o C. Disinfection efficiency of the Ag@ZnO core-shell nanoparticles was confirmed in case of real world water samples from pond, river, municipal tap and was found to be better than that of pure ZnO and TiO2 (Degussa P25). When the nanoparticle based catalyst was recycled and reused for subsequent disinfection experiments, its efficiency did not change remarkably even after three cycles. The sonochemically synthesized Ag@ZnO core-shell nanoparticles have a good potential for application in solar photocatalytic disinfection of water borne pathogens.

During flux weakening operation time (FWOT), the total iron loss rises and affects the accuracy of loss prediction and efficiency especially if a large range of FWOT exists. Iron loss prediction is widely employed in investigations for a fast electrical machine analysis using 2-D FEA. This paper studies harmonic loss analytically by a steady-state equivalent circuit. Consideration of skin effects and iron saturation are utilized in order to examine the accuracy through the relative error distribution in the frequency domain of each model from 50 to 700 Hz. Additionally, this comparative study presents a torque-frequency-flux density calculation over each single term of the modified IEM-formula. The analytical calculation is performed using 2-D FEA for a classic and modified IEM-formula along with experimental verifications on a surface-mounted PMSG for a wind generation application.

The detection of dopamine in a highly sensitive and selective manner is crucial for the early diagnosis of a number of neurological diseases/disorders. Here, a report on a new platform for the electrochemical detection of dopamine with a considerable accuracy that comprises a 3D porous graphene oxide (pGO)/gold nanoparticle (GNP)/pGO composite-modified indium tin oxide (ITO) is presented. The pGO was first synthesized and purified by ultrasonication and centrifugation, and it was then further functionalized on the surface of a GNP-immobilized ITO electrode. Remarkably, owing to the synergistic effects of the pGO and GNPs, the 3D pGO-GNP-pGO-modified ITO electrode showed a superior dopamine-detection performance compared with the other pGO- or GNP-modified ITO electrodes. The linear range of the newly developed sensing platform is from 0.1 μM to 30 μM with a limit of detection (LOD) of 1.28 μM, which is more precise than the other previously reported GO-functionalized electrodes. Moreover, the 3D pGO-GNP-pGO-modified ITO electrodes maintained their detection capability even in the presence of several interfering molecules (e.g., ascorbic acid, glucose). The proposed platform of the 3D pGO-GNP-pGO-modified ITO electrode could therefore serve as a competent candidate for the development of a dopamine-sensing platform that is potentially applicable for the early diagnosis of various neurological diseases/disorders.

The most significant assumptions in the subdomain technique (i.e., based on the formal resolution of Maxwell's equations applied in subdomain) is defined by: “The iron parts (i.e., the teeth and the back-iron) are considered to be infinitely permeable so that the saturation effect is neglected”. In this paper, the author presents a new scientific contribution on improving of this method in two-dimensional (2-D) and in Cartesian coordinates by focusing on the consideration of iron. The subdomains connection is carried out in the two directions (i.e., x- and y-edges). For example, the improvement was performed by solving magnetostatic Maxwell's equations for an air- or iron-cored coil supplied by a direct current. To evaluate the efficacy of the proposed technique, the magnetic flux density distributions have been compared with those obtained by the 2-D finite-element analysis (FEA). The semi-analytical results are in quite satisfying agreement with those obtained by the 2-D FEA, considering both amplitude and waveform.

Thalassemia is genetic blood disease cause by absence or decrease of one or more of the globin chain synthesis. Beta thalassemia is characterized by one or more mutations in beta globin gene. Absence or reduced amount the of beta globin chains cause ineffective erythropoiesis which leads to anemia. Beta thalassemia has been further divided into three main forms: Thalassemia minor/silent carrier, major and intermedia. More severe form is thalassemia major in which patients depend upon blood transfusion for survival and high level of iron occur as a consequence of consistent blood transfusion. Over loaded iron invokes the synthesis of reactive oxygen species that are toxic in redundancy and triggering the impairment to vascular, endocrine and hepatic system. Thalassemia can be diagnosed and detected through various laboratory tests such as blood smear, prenatal testing (genetic testing of amniotic fluid), DNA analysis (genetic testing) and complete blood count. Treatment of thalassemia intermedia is symptomatic but it can also be managed by splenectomy and folic supplementation. While thalassemia major can be treated by transplantation of bone marrow, regular transfusion of blood and iron chelation treatment, stimulation of fetal hemoglobin production, hematopoietic stem cell transplantation and gene therapy.

Two types of heterometallic (Fe(III),Na) silsesquioxanes [Ph₅Si₅O₁₀]₂[Ph₁₀Si₁₀O₂₁]Fe₆(O^2‒)₂Na₇(H₃O⁺)(MeOH)₂(MeCN)_4.5.1.25(MeCN), I, and [Ph₅Si₅O₁₀]₂[Ph₄Si₄O₈]₂Fe₆Na₆(O^2‒)₃(MeCN)_8.5(H₂O)_8.44, II, were obtained and characterized. X-Ray studies established distinctive structures of both products, with pair of Fe(III)-O-based triangles surrounded by siloxanolate ligands, giving fascinating cage architectures. Complex II proved to be catalytically active in the formation of amides from alcohols and amines, thus becoming a rare example of metallasilsesquioxanes performing homogeneous catalysis. Benzene, cyclohexane and other alkanes, as well as alcohols, can be oxidized in acetonitrile solution to phenol, the corresponding alkyl hydroperoxides and ketones, respectively, by hydrogen peroxide in air in the presence of catalytic amounts of complex II and trifluoroacetic acid. Thus, the cyclohexane oxidation at 20 °C gave oxygenates in very high for alkanes yield (48% based on alkane). The kinetic behaviour of the system indicates that the mechanism includes the formation of hydroxyl radicals generated from hydrogen peroxide in its interaction with diiron species. The latter are formed via monomerization of starting hexairon complex with further dimerization of the monomers.

Titanium dioxide (TiO2) and aluminum oxide (Al2O3) coatings have been investigated in a wide range of bio-applications due to their biodegradation and biocompatibility properties, that are key parameters for their use in the food packaging and biomedical devices fields. The present study evaluates and compares the electrochemical behavior of the non-coated, commercial resin-coated, TiO2-coated and Al2O3-coated aluminum in commercial beer electrolyte. For this, TiO2 and Al2O3 thin films were deposited on aluminum (Al) substrates using atomic layer deposition (ALD). The evaluation of the corrosion barrier layer properties was performed by linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS). In addition, profilometry, grazing incidence X-ray diffractometry (GIXRD), scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR) analyses were performed to investigate the physical and chemical properties of the pristine and / or corroded samples. TiO2 and Al2O3 films presented an amorphous structure, a morphology that follows Al substrate surface, and a thickness of around 100 nm. Analysis of LSV data showed that ALD coatings promoted a considerable increase in corrosion barrier efficiency being 86.3% for TiO2-coated Al and 80% for Al2O3-coated Al in comparison with 7.1% of commercial resin-coated Al. This is mainly due to the lower electrochemical porosity, 11.4% for TiO2-coated Al and 20.4% for Al2O3-coated Al in comparison with 96% of the resin-coated Al, i.e. an increase of up to twofold in the protection of Al when coated with TiO2 compared to Al2O3 coated. The EIS results allow us to complement the discussions about the reduced corrosion barrier efficiency of the Al2O3 film for beer electrolyte once SEM and FT-IR analyzes did not show drastic changes in both investigated ALD films after the corrosion assays. The above results indicate that ALD TiO2 and Al2O3 films may be a viable alternative to replace the synthetic resin coatings frequently used in aluminum cans of use in the food industry.

Porosity in plasma sprayed coatings is vital for most engineering applications. It is either advantageous or disadvantageous depending on the functionality of the coating and the immediate working environment. Consequently, the formation mechanisms and development of porosity has been extensively explored to find out modes of controlling porosity in plasma sprayed coatings. In this work, a comprehensive review of porosity on plasma sprayed coatings is established. The formation and development of porosity on plasma sprayed coatings are governed by set spraying parameters. Optimized set spraying parameters have been used to achieve the most favorable coatings with minimum defects. Even with the optimized set spraying parameters, defects like porosity still occur. Here, we discuss other ways that can be used to control porosity in plasma sprayed coating with emphasis to atmospheric plasma sprayed chromium oxide coatings. Techniques like multi-layer coatings, nano-structured coatings, doping with rare earth elements, laser surface re-melting and a combination of the above methods have been suggested in adjusting porosity. The influences of porosity on properties of plasma sprayed coatings and the measurement methods of porosity have also been reviewed.

Maghemite (γ-Fe2O3) is a mineral formed from magnetite oxidation at low temperatures, an intermediate metastable term of the magnetite to hematite oxidation and could be mixed with both. It has magnetic susceptibility similar to magnetite, crystal structure close to magnetite with which it forms a solid solution, while compositionally it equals hematite. Maghemite is thus easily misidentified as magnetite by X-ray diffraction and/or as hematite by spot chemical analysis in iron ore characterization routines. Nonstoichiometric magnetite could be quantified in samples of Brazilian soils and iron ores by the Rietveld method using a constrained refinement of the X-ray patterns. The results were confirmed by reflected light microscopy and Raman spectroscopy, thus qualitatively validating the method. X-ray diffraction with the refinement of the isomorphic substitution of Fe2+ by Fe3+ along the magnetite-maghemite solid solution could help to suitably characterize maghemite in iron ores, allowing for the evaluation of its ultimate influence on mineral processing, by affecting its surface and breakage properties.

Pearl millet is an important food crop in the arid and semi-arid tropical regions of Africa and Asia. These regions are home to millions of poor smallholder’s households living in harsh agro ecology and reported higher prevalence of malnutrition. Such poor households have few options in terms of food crops, besides the limited markets. Indeed, pearl millet is one of the food crops they continue to grow for their food and nutritional security. Pearl millet is important sources of dietary carbohydrates, energy, protein, and important minerals such as calcium, iron and zinc. Considering inherent high nutritional values and climate resilient nature (drought and heat), demand for pearl millet as food, beside valued for its Stover as a source of livestock fodder, is projected to grow strongly in Asia (India) and Africa (West and Central Africa). Iron (cause anemia) and zinc (cause stunting) deficiencies are widespread and serious public health problems worldwide, including India and Africa. Biofortification is a cost-effective and sustainable agricultural strategy to address this problem. Research on pearl millet has shown that large genetic variability (30-140 mg/kg Fe and 20-90 mg/kg Zn) available in this crop can be effectively utilized to develop high-yielding cultivars with high iron and zinc densities. Both Open –pollinated varieties (Dhanshakti and Chakti) and hybrids (ICMH 1202, ICMH 1203 and ICMH 1301) of pearl millet with high grain yield (>3.5 tons/ha in hybrids) and high levels of iron (70-75 mg/kg) and zinc (35-40 mg/kg) densities have been developed and released. Currently, India growing >70,000 ha of biofortified pearl millet, besides more pipeline hybrids and varieties are under various stage of testing at the national (India) and international (west Africa) trials for possible release. Genomic tools will be an integral part of breeding program particularly for nutritional traits to use diagnostic markers and genomic selection. Clinical studies showed that 200g grains from biofortified cultivar would provide bioavailable Fe to meet full recommended daily allowance (RDA) in children, adult men and 80% of the RDA in women. Till today, no markets to promote biofortified cultivars/grains/products as no incentive price and such products aims to address food and nutritional security challenges simultaneously. The demand is likely to increase only after investment and integration into modern public distribution system, nutritional intervention schemes, private seed and food companies with strong mainstreaming nutritional policies. In the non-traditional regions, this will contribute to livestock and poultry feed industry as spill-over benefits to improve nutrition.

Dental anxiety (DA) negatively affects patients’ oral and overall health. This study explored attitudes and clinical practices of licensed Ohio general dentists who treat patients with DA. Methods: An anonymous self-administered mail survey was sent to 500 general dentists licensed and practicing in Ohio. Responses to 21 pre-coded questions were analyzed. Frequencies were examined; cross-tabs, Chi-Square, and Fischer’s Exact Test were calculated for statements according to dentists’ gender. Alpha was set at p = 0.05. Results: Nearly all respondents treated anxious patients; males were more likely to find it challenging than females. Dentists were most familiar with distraction, although half found nitrous oxide to be an effective tool. Female dentists were more likely than males to be familiar with anxiolytics and find them effective. Conclusion: Overall, Ohio general dentists are most familiar with using distraction and nitrous oxide during appointments for anxious patients. Gender differences exist in attitudes towards anxiolytic use for patients with DA. Practice Implications: By identifying techniques that are comfortable for patient and practitioner, oral health disparities associated with DA may be reduced.

Copper smelting slag is a solution of molten oxides created during the copper smelting and refining process, and about 1.5 million tons of copper slag is generated annually in Korea. Oxides in copper smelting slag include ferrous (FeO), ferric oxide (Fe­₂O₃), silica (SiO­₂ from flux), alumina (AI₂O₃), calcia (CaO) and magnesia (MgO). Main oxides in copper slag, which iron oxide and silica, exist in the form of fayalite (2FeO·SiO₂). Since the copper smelting slag contains high content of iron, and copper and zinc. Common applications of copper smelting slag are the value added products such as abrasive tools, roofing granules, road-base construction, railroad ballast, fine aggregate in concrete, etc., as well as the some studies have attempted to recover metal values from copper slag. This research was intended to recovery Fe-Cu alloy, raw material of zinc and produce reformed slag like a blast furnace slag for blast furnace slag cement from copper slag. As a results, it was confirmed that reduction smelting by carbon at temperatures above 1400°С is possible to recover pig iron containing copper from copper smelting slag, and CaO additives in the reduction smelting assist to reduce iron oxide in the fayalite and change the chemical and mineralogical composition of the slag. Copper oxide in the slag can be easily reduced and dissolved in the molten pig iron, and zinc oxide is also reduced to a volatile zinc, which is removed from the furnace as the fumes, by carbon during reduction process. When CaO addition is above 5wt.%, acid slag has been completely transformed to calcium silicate slag and observed like blast furnace slag.

INTRODUCTION. The most common cause of eating non-food items (pica) is specific deficiencies of minerals, such as iron. This study aimed to assess the relationship between Pica and Iron deficiency anemia among pregnant women. METHODS. The study was conducted in the out-patient department, antenatal Clinic at East Jeddah Hospital from July to September 2020. Design: A quantitative descriptive correlation design. Sample size: A total of 400 pregnant women, included anemic pregnant women, ≥ 18 years old, with singleton fetus and iron deficiency anemia. RESULTS. The mean age was 32.2 ± 6.6, half of the participants reported food cravings. Ice was the main item in pica followed by clay and chalk. Two-thirds had pica, more than half during the 1st trimester. There is a statistically significant relationship between pica and the history of a family member, parity, and gravidity at (P< 0,001, P <0,001, P <0,005) respectively. Hb and hematocrit in relation to pica reflected a statistically significant relationship (P< 0,001) and (P< 0,001), respectively. The symptoms attributed to iron deficiency were significantly associated with pica (P< 0,006). CONCLUSION. The pica and iron deficiency anemia had a significant association with pregnant women in EJH. RECOMMENDATION. The follow-up visits should integrate the food behavior inquiry to check if the pica existing with anemic or non-anemic pregnant women. Also, increase the awareness among midwives-nurses about the prevalence of pica and iron deficiency anemia among pregnant women.

Electrochemical impedance (EI) measurements were performed to evaluate the nylon 66/-tetra-(para-aminophenyl) porphyrin (H₂T(p-NH₂)PP)/graphene oxide (GO) film coating on stainless steel and compared to the nylon/H₂T(p-NH₂)PP and nylon/GO film samples using 1M H₂SO₄ as electrolyte. The nylon/H₂T(p-NH₂)PP and nylon/GO composite films showed high electrochemical impedance in the order of 109 ohm-cm² and a system controlled by mass transfer, product of a diffusion process at low frequencies with a resistance up to 5 orders of magnitude, indicating the diffusion of protons through the coating and a decrease in the metal dissolution. Otherwise, the nylon/H₂T(p-NH₂)PP/GO film compound evaluated show good ionic conductivity and electrochemical stability in the acid environment, acting porphyrin as a catalyst to the passage of protons through the film, reducing its electrochemical impedance up to 7 orders of magnitude with respect to the compounds nylon/H₂T(p-NH₂)PP and nylon/GO. Likewise, good capacitance values are also shown by modifying the concentrations of porphyrin and GO reinforcing materials. These properties are important for technological applications, such as anticorrosion coating for bipolar plates or membrane in a fuel cell type PEM, super-capacitors, etc.

Growing crystals of nickel niobate (NiNb2O6), we noticed that changing growth conditions allowed our material to enter different areas of the phase diagram. In particular, we found that excess material accumulated within and above the liquid zone. Analysis showed that this was an unincorporated constituent. Changing the ratio of the constituent oxides - an excess of ~4% of either NiO or Nb2O5 gave us the opportunity to investigate changes in zone stability, melting temperature and quality of the resulting crystal. We found that a small excess of nickel oxide decreases the melting temperature significantly, and created the best pseudo-rutile NiNb2O6 crystal studied, while higher amounts of niobium oxide allowed us to stabilize the NiNb2O6 columbite phase. This research reinforces the idea that self-flux as a travelling solvent can significantly impact crystal growth parameters and quality.

In this work, we report synthesis of Cu, Pt and Pd doped SnO₂ powders and their comparative CO gas sensing studies. Dopants were incorporated into SnO₂ nanostructures using chemical and impregnation methods by using urea and ammonia as precipitation agents. The synthesized samples were characterized using X-ray diffraction (XRD), Raman spectroscopy, Scanning electron microscopy (SEM) and High resolution transmission electron microscopy (HR-TEM). The presence of dopants within the SnO₂ nanostructures was evidenced from HR-TEM. Doped powders utilizing chemical methods with urea as precipitation agent presented higher sensitivities compared to the remaining, which is due to the formation of uniform and homogeneous particles resulted from the temperature assisted synthesis. The particle sizes of doped SnO₂ nanostructures were in the range of 40-100 nm. An enhanced sensitivity around 1783 was achieved with Cu doped SnO₂ when compared with two other dopants i.e., Pt (1200) and Pd: SnO₂(502). The high sensitivity of Cu: SnO₂ is due to formation of CuO and its excellent association and dissociation in the presence of CO with adsorbed atmospheric oxygen at sensor operation temperatures resulted in high conductance. Cu: SnO₂ may be an alternative and cost effective sensor for industrial applications.

The cause-effect relationship between iron deficiency anemia (IDA) and osteoporosis has not been established in the general population. Thus, the current longitudinal study determined the role of IDA as a risk factor for osteoporosis by analyzing a large nationwide population-based sample. In a sample of 1,000,000 randomly sampled individuals from the 1998-2012 Taiwan National Health Insurance Research Database, patients with IDA (case group [n=35,751]) and individuals without IDA (control group [n=178,755]) were compared. Patients who were <20 years of age and who had pre-existing osteoporosis prior to the diagnosis of IDA were excluded. Each patient with IDA was age- and gender-matched to 5 individuals without IDA. The diagnoses of IDA and osteoporosis (coded using ICD-9CM) were further confirmed with blood test results and X-ray bone densitometry to ensure the accuracy of the diagnoses. Osteoporosis occurred more often among patients with IDA compared to individuals without IDA (2.27% vs. 1.32%, p<0.001). Cox proportional hazard analysis revealed that the risk for osteoporosis was significantly higher in the case than the control group (hazard ratio [HR]=1.74; 95% CI=1.61-1.88) and remained similar after adjustment for covariates (adjusted HR=1.81; 95% CI=1.67-1.97). Compared with individuals without IDA, the risk for osteoporosis was even higher for patients with IDA who received intravenous ferrum therapy (adjusted HR=2.21; 95% CI=1.85-2.63). In contrast, the risk for osteoporosis was reduced for patients with IDA who received a blood transfusion (adjusted HR=1.47; 95% CI=1.20-1.80). As a predictor, prior IDA is a significant and independent risk factor for development of osteoporosis. In contrast to blood transfusion treatment, the use of intravenous ferrum may further increase the risk for future osteoporosis.

A field experiment was conducted for 2 years in Green Tea Laboratory of Saitama Prefectural Agriculture and Forestry Research Center, Iruma, Saitama, Japan from March 2014 to December 2015. Controlled release fertilizers (CRF) or organic fertilizers (ORG) which is the mixture of chicken manure and oil cakewere applied with the amount of 450 kg N ha^-1 yr^-1 in 2014 and 397 kg N ha^-1 yr^-1 in 2015. Nitrous oxide (N₂O) emissionsfrom soil in green tea fields were measured by closed chamber method. The results showed that CRF has significantly lower N₂O compared to ORG. The cumulative N₂O emissions from CRF accounted for 51% of N₂O emissions from ORG fields and 138% of control with no fertilizer treatment. The N₂O flux from the row was higher than that of under the canopy, since fertilizer were applied on the row. However the total emission from the area between the rows was lower than that under the canopy because of the area ratio of row and canopy was 1:5.

In this study, a high energy conversion efficient dye-sensitized solar cells (DSSC) was successfully fabricated by attaching a double anti-reflection (AR) layer which is composed of a subwavelength moth-eye structured polymethyl methacrylate (PMMA) film and a polydimethylsiloxane (PDMS) film. The efficiency is up to 6.79%. The moth-eye structured PMMA film was fabricated by using anodic aluminum oxide (AAO) template which is simple, low-cost and scalable. The nano-pattern of AAO template has been precisely reproduced onto PMMA film. The photoanode is composed of Titanium dioxide (TiO₂) nanoparticles (NPs) with diameter of 25 nm deposited on the fluorine-doped tin oxide (FTO) glass substrate and the sensitizer N3. The double AR layer can effectively improve the short-circuit current density (JSC) and conversion efficiency from 14.77 to 15.79 mA/cm² and from 6.26% to 6.79%, respectively.

Zinc oxide (ZnO) nanostructures have been studied extensively in the past years due to the novel electronic, photonic, mechanical and electrochemical properties. Recently, more attention has been paid to assemble nanoscale building blocks into three dimensional (3D) complex hierarchical structures, which not only inherit the excellent properties of the single building blocks but also provide potential applications in the bottom-up fabrication of functional devices. This review article focuses on 3D ZnO hierarchical nanostructures, and summarizes major advances in the solution phase synthesis, applications in environment, and electrical/electrochemical devices. We present the principles and growth mechanisms of ZnO nanostructures via different solution methods, with an emphasis on rational control of the morphology and assembly. We then discuss the applications of 3D ZnO hierarchical nanostructures in photocatalysis, field emission, electrochemical sensor, and lithium ion batteries. Throughout the discussion, the relationship between the device performance and the microstructures of 3D ZnO hierarchical nanostructures will be highlighted. This review concludes with a personal perspective on the current challenges and future researches.

Soil microbial fuel cells (sMFC) are a novel technique that use organic matters in soils as an alternative energy source. External resistance (ER) is a key factor influencing sMFC performance and, furthermore, alters the soil’s biological and chemical reactions. However, little information is available on how the microbial community and soil component changes in sMFC with different ER. Therefore, the effects of anodes of sMFC at different ER (2000 Ω, 1000 Ω, 200 Ω, 80 Ω and 50 Ω) were examined by measuring organic matter (OM) removal efficiency, trace elements in porewater and bacterial community structure in contaminated paddy soil. The results indicated that ER has significant effects on sMFC power production, OM removal efficiency and bacterial beta diversity. Moreover ER influences iron, arsenic and nickel concentration as well in soil porewater. In particular, greater current densities were observed at lower ER (2.4mA, 50Ω) compared to a higher ER (0.3mA, 2000Ω). The removal efficiency of OM increased with decreasing ER whereas it decreased with soil distance away from the anode. Furthermore, principal coordinate analysis (PCoA) revealed that ER may shape the bacterial communities that develop in the anode vicinity but have minimal effect on that of the bulk soil. The current study illustrates that lower ER can be used to selectively enhance the relative abundance of electrogenic bacteria and lead to high OM removal.

Copper-based nanoparticles were synthesized using the glycine–nitrate process (GNP) by using copper nitrate trihydrate [Cu(NO₃)₂‧3H₂O] as the main starting material and glycine [C₂H₅NO₂] as the complexing and incendiary agent. The as-prepared powders were characterized through X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) analysis, X-ray photoelectron spectroscopy, and scanning electron microscopy. Using Cu(NO₃)₂.3H₂O as the oxidizer (N) and glycine as fuel (G), we obtained CuO, mixed-valence copper oxides (CuO + Cu₂O, G/N = 0.3–0.5), and metallic Cu (G/N = 0.7). The XRD and BET results indicated that increasing the glycine concentration (G/N = 0.7) and reducing particle surface area increased the yield of metallic Cu. The effects of varying reaction parameters such as catalyst activity, catalyst dose, and H₂O₂ concentration on nonylphenol-9-polyethoxylate (NP9EO) degradation were assessed. With a copper‐based catalyst in a heterogeneous system, the NP9EO and total organic carbon removal efficiencies were 83.1% and 70.6%, respectively, under optimum operating conditions (pH, 6.0; catalyst dose, 0.3 g/L; H₂O₂ concentration, 0.05 mM). The results suggested that removal efficiency increased with an increase in H₂O₂ concentration but decreased when the H₂O₂ concentration exceeded 0.0.5 mM. Furthermore, the trend of photocatalytic activity was as follows: G/N = 0.5 > G/N = 0.7 > G/N = 0.3. The G/N = 0.5 catalysts showed the highest photocatalytic activity and resulted in 94.6% NP9EO degradation in 600 min.

Nitric oxide (NO) is involved in physiological processes, including vasodilatation, wound healing and antibacterial activities. As NO is a free radical, designing drugs to generate therapeutic amounts of NO in controlled spatial and time manners is still a challenge. In this study, the NO donor S-nitrosoglutathione (GSNO) was incorporated into the thermoresponsive Pluronic F-127 (PL) - chitosan (CS) hydrogel, with an easy and economically feasible methodology. CS is a polysaccharide with known antimicrobial properties. Scanning electron microscopy, rheology and differential scanning calorimetry techniques were used for hydrogel characterization. The results demonstrated that the hydrogel has a smooth surface, thermoresponsive behavior and good mechanical stability. The kinetics of NO release and GSNO diffusion from GSNO-containing PL/CS hydrogel demonstrated a sustained NO/GSNO release, in concentrations suitable for biomedical applications. The GSNO-PL/CS hydrogel demonstrated a concentration-dependent toxicity to Vero cells, and antimicrobial activity to Pseudomonas aeruginosa (minimum inhibitory concentration and minimum bactericidal concentration values of 0.5 µg·mL^-1 of hydrogel, which corresponds to 1 mmol·L^-1 of GSNO). Interestingly, the concentration range in which the NO-releasing hydrogel demonstrated an antibacterial effect was not found to be toxic to the Vero mammalian cell. Thus, the GSNO-PL/CS hydrogel is a suitable biomaterial for topical NO delivery applications.

A cuprous oxide (Cu₂O) thin layer served as the base for a non-enzymatic glucose sensor in an alkaline medium, 0.1 NaOH solution, with a linear range of 50-200 mg/dL using differential pulse voltammetry (DPV) measurement. An X-ray photoelectron spectroscopy (XPS) study confirmed the formation of the cuprous oxide layer on the thin gold film sensor prototype. Quantitative detection of glucose in both phosphate-buffered saline (PBS) and undiluted human serum were carried out. Neither ascorbic acid nor uric acid even at a relatively high concentration level of 100mg/dL in serum interfered with the glucose detection, demonstrating the excellent selectivity of this non-enzymatic cuprous oxide thin layer based glucose sensor. Chronoamperometry (CA) and single potential amperometric voltammetry were used to verify the measurements obtained by differential pulse voltammetry (DPV), and the positive results validated that the detection of glucose in a 0.1 M NaOH alkaline medium by DPV measurement was effective. Nickel, platinum and copper are commonly used metals for non-enzymatic glucose detection. The performance of these metal-based sensors for glucose detection using DPV were also evaluated. Cuprous oxide (Cu₂O) thin layer based sensor showed the best sensitivity for glucose detection among the sensors evaluated.

Highly colloidal Eu-doped Gd2O3 nanoparticles(core-NPs) were synthesized by thermal decomposition via weak base at low temperature (150oC), subsequently, silica layers were deposited to increased colloidal stability, solubility, biocompatibility and no-toxicity at the environmental condition. XRD results indicate the highly purified, crystalline, single phase cubic phase Gd2O3 nanocrystals. TEM image shows the mesoporous thick silica layer was effectively coated over the core nanocrystals, which have irregular size with nearly spherical shape and a mean grain size is about 10-30 nm. Absorption spectra and zeta potential results in aqueous media revealed that solubility, colloidal stability, and biocompatibility character was enhanced from core to core-shell structure because of silica layer surface encapsulation. The samples demonstrate excellent photoluminescence properties (dominant emission 5D0→7F2 transition in red region at 610 nm) indicated the advantage to use in optical bio-detection and bio-labeling etc. The photoluminescence intensity of the silica shell modified core/shell nanoparticles were suppressed relatively core-nanoparticles, it indicates the multi-photon relaxation pathways arising from the surface coated high vibrational energy molecules of the silanol groups. The core/nSiO2/mSiO2 nanocrystals display strong emission (5D0→7F2) transition along with excellent solubility and biocompatibility, which may find promising applications in photonic based biomedical applications.

Graphene is a remarkable material with numerous applications. Due to its thin and lightweight design, it is ideal for a variety of applications. The synthesis of high-quality graphene in a cost-effective and environmentally friendly manner continues to be a significant challenge. Chemical reduction is considered to be the most advantageous method for preparing reduced graphene oxide (rGO). However, this process necessitates the use of toxic and harmful substances, which can have a detrimental effect on the environment and human health. Thus, to accomplish the objective, the green synthesis principle has prompted researchers worldwide to develop a simple method for green reduction of graphene oxide (GO), which is readily accessible, sustainable, economical, renewable, and environmentally friendly in nature. For example, the use of natural materials such as plants is generally considered safe. Furthermore, plants contain reducing and capping agents. The current review will focus on the discovery and application of rGO synthesis using extracts from a variety of different parts of the plant. The review aims to aid current and future researchers in their search for a novel plant extract that acts as a reductant in the green synthesis of rGO. The review aims to assist current and future researchers in their research for a novel plant extract that acts as a reductant in the green synthesis of rGO as well as their potential applications in a variety of industries.

Magnetic Resonance Imaging (MRI) is a powerful, non-invasive and nondestructive tool, capable of providing three-dimensional (3D) images of living organisms. The use of magnetic contrast agents has allowed clinical researchers and analysts to enormously increase the sensitivity and specificity of MRI since these substances change the intrinsic properties of the tissues within a living body, increasing the information present in the images. The advances in nanotechnology and materials science as well as the research of new magnetic effects have been the driving forces that propel the use of magnetic nanostructures as promising alternatives to the commercial contrast agents used in MRI. This review discusses the principles associated with the use of contrast agents in MRI as well as the most recent reports focused on nanostructured contrast agents. The potential applications of gadolinium (Gd) and manganese Mn-based nanomaterials and iron oxide nanoparticles in this imaging technique are discussed as well, from their magnetic behavior to the mainly used materials and nanoarchitectures. Then, it is also addressed the recent efforts made to develop new types of contrast agents based on synthetic antiferromagnetic and high-aspect ratio nanostructures. Furthermore, the application of these materials in theragnosis, either as contrast agents and controlled drug release, contrast agents and thermal therapy or contrast agents and radiosensitizers, is also presented.

Graphene oxide was synthesized by a one-step environmentally friendly mechanochemistry process directly from graphite and characterized by Raman, FT-IR and UV/vis spectroscopies, Atomic Force Microscopy, X-ray Diffraction, Scanning Electron Microscopy, Energy-Dispersive X-ray Spectroscopy and Thermogravimetric Analysis. Spectroscopic analysis shows that the functional groups and oxygen content of the synthesized material are comparable with those of graphene oxide synthesized by other previously reported methods (Hummers). Thermogravimetric analysis reveals thermal stability up to 400 °C.

Dental caries is a public health problem worldwide according to WHO data. Among treatments in pediatric dentistry, prefabricated metal crowns (PMCs) have been one of the most successful options since they were introduced in cases of considerable tooth destruction. Our objective was to detect the presence and concentration of iron (Fe), chromium (Cr), and nickel (Ni) in saliva of patients who require rehabilitation with PMCs, before and after their placement. A quasi-experimental study was performed in 32 patients who attended dental care in a pediatric dentistry clinic at a public university and who required rehabilitation with PMCs. Parametric tests (ANOVA and Pearson correlation) were performed, and a p ≤ 0.05 was considered statistically significant. Statistically significant differences were found when comparing the Ni release before, 1 week, and 1 month after placing the crowns. Similarly, we observed a positive correlation between the number of crowns and Ni release. No tests were performed for Fe and Cr because the amounts of these metals were less than 0.1 ppb, which was not detectable by inductively coupled plasma optical emission spectrometry (ICP-OES). The levels of Fe, Cr, and Ni released were below toxic health levels. Studies are required to evaluate whether this release has negative effects at cellular levels.

Considering the manufacturing of automotive components, there exists a dilemma around the substitution of traditional Cast Iron (CI) with lighter metals. Nowadays, aluminium alloys, being lighter compared to traditional materials, are considered as a more environmentally friendly solution. However, the energy required for the extraction of the primary materials and manufacturing of components is usually not taken into account in this debate. In this study, an extensive literature review has been performed to estimate the overall energy required for the manufacturing of an engine cylinder block using (a) cast iron and (b) aluminium alloys. Moreover, data from over 100 automotive companies, ranging from mining companies to consultancy firms, have been collected in order to support the soundness of this investigation. The environmental impact of the manufacturing of engine blocks made of these materials is presented with respect to the energy burden; the “cradle-to-grave approach” has been implemented to take into account the energy input of each stage of the component lifecycle starting from the resource extraction and reaching to the end-of-life processing stage. Our results indicate that although aluminium components contribute towards reduced fuel consumption during their use phase, the vehicle distance needed to be covered in order to compensate for the up-front energy consumption related to the primary material production and manufacturing phases is very high. Thus, the substitution of traditional materials with lightweight ones in the automotive industry should be very thoughtfully evaluated.

Multi-walled carbon nanotubes (MWCNTs) and graphene oxide (GO) reinforced carbon foam (CF) composite were prepared by direct pyrolysis of MWCNTs, GO and mesophase coal tar pitch. The effect of additive amount of the mixture of MWCNTs and GO on the microstruture and properties of carbon foam was analzyed by transmission electron miscroscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Four-probe resistance meter, universal testing machine, and laser thermal conductivity tester respectively. The result shows that MWCNTs and GO had significant impact on the microstructure of carbon foam. Futhermore, the electrical, mechanical and thermal properties of carbon foam composites were significantly enhanced by increasing the additive amount. Maximum compressive strenght of 19.2 MPa and Young’s modulus of 56.8 MPa of CF composite were observed. Similarly, Highest thermal conductivity of 30.91 W/m.K and electrical conductivity of 27.2 ×103 S/m were observed at 2 wt. % of MWCNTs-GO additive loading.

The world is facing a serious energy crisis and environmental pollution problems due to a sharp increase in the world population. Bioenergy is an eminent solution to these problems. Anaerobic digestion is a green energy technology used worldwide for the conversion of organic waste to biogas. It is reported that organic wastes are hard to digest and need some technical improvement in the anaerobic digestion process to improve biogas yield. Iron-based additives, due to their electron acceptance and donation capabilities, have been emphasized as being exceptional in improving anaerobic digestion process efficiency amongst all other enhancement options. This study reviews the major available types of iron-based additives, their characteristics, and their preparation methods. The preferred iron-based additive that has a significant effect on the enhancement of biogas yield is also discussed. The use of iron-based additives in the anaerobic digestion process with varying dosages and their impact on the biogas generation rate is also being studied. Substrates, operating parameters, and types of anaerobic digesters used in recent studies while researching the effects of iron-based additives are also part of this review. Lastly, this study also confirms that iron-based additives have a significant effect on the reduction rate of the volatile suspended solids, methane content, biogas yield, and volatile fatty acids.

Influence of water concentration on the properties of fluorine-doped tin oxide (FTO) thin films was systematically studied in this work. Home made SISOM’s SPEED techniques and its chemical formulation was employed to grow the FTO on quartz substrate. Water concentration in the precursor solution was varied from 0, 0.5, 1.0 and 1.5 mol %. The structural, optical, and electrical properties of the films were studied under these deposition conditions. The results show that the properties of the films varied significantly with water concentration. Scanning electron microscopy (SEM) revealed FTO films whose grain size and uniformity increases significantly with increase in water concentration. The structure of the films was measured by X-ray diffraction (XRD) measurement. It shows polycrystalline films with (110), (101), (200), (211) and (220) orientation; the strength increases as water concentration increases. The optical transmission was determined by UV-Vis spectroscopy at 380–780 nm UV-VIS regions. The optical transmittance varies with water concentration with an average of 84%. The electrical property, measured by Hall Effect revealed n-type semiconductor. The films have the following properties: resistivity, 15 × 10^-4Ω cm; carrier concentration, 18.7 × 10¹⁹ cm^-3 and mobility of 21.86 cm² V^-1 s^-1. The average figure of merit, φ of the FTO film is 1.25. Optimum deposition condition was established after series of experiments and was found to be 1.5% water concentration at 460^oC substrate temperature. The FTO films deposited in this work could be a promising replacement to indium tin oxide (ITO) especially in dye-sensitized solar cells.

Foods are mixed with saliva in the oral cavity and swallowed. During staying in the stomach, saliva is contentiously provided to mix with the ingested foods. Because a salivary component nitrite is protonated to produce active nitrous acid at acidic pH, the redox reactions of nitrous acid with phenolic compounds in foods become possible in the stomach. In the reactions, nitrous acid is reduced to nitric oxide (•NO), producing various products from phenolic compounds. In the products, stable hydroxybezoyl benzofuranone derivatives, which are produced from quercetin and its 7-O-glucoside, are included. Caffeic acid, chlorogenic acid, and rutin are oxidized to quinones and the quinones can react with thiocyanic acid derived from saliva producing stable oxathiolone derivatives. 6,8-Dinitrosocatechis are produced from catechins by the redox reaction, and the dinitrocatechins are oxidized further by nitrous acid producing the quinones, which can make charge transfer complexes with the dinitrosocatechin and can react with thiocyanic acid producing the stable thiocyanate conjugates. In this way, various products can be produced by the reactions of salivary nitrite with dietary phenolic compounds, and reactive and toxic quinones formed by the reactions are postulated to be removed in the stomach by thiocyanic acid derived from saliva.

Iron oxide nanoparticles are widely used as contrast agent for MRI and may be used as therapeutic agent by magnetic hyperthermia if they display a high magnetic anisotropy. Considering the effect of the nanoparticles shape on anisotropy, the reproducible shape control of nanoparticles is currently a challenge of synthesis methods. By investigating reaction parameters which are the iron precursor structure, the water content and the amount of the surfactant, sodium oleate, reported to trigger the cubic shape, iron oxide nanoparticles with different shape and composition were observed to form. In particular, iron oxide nanoplates have been thus synthesized. The effect of the surfactant coming from precursor was taking into account by using in house iron stearates bearing either two or three stearate chains and the negative effect of water on shape was confirmed by considering these precursors after their dehydration. Nanocubes with straight faces and a FeO@Fe3-xO4 composition were obtained only with dehydrated precursors and 50% of sodium oleate in the oleic acid and sodium oleate surfactant mixtures. When iron stearates with three chains led mainly to nanocubes in presence of soduim oleate, Iron stearates with two chains led to the formation of nanoplates with 80% of sodium oleate. The original flat shape of the plates was confirmed with 3D TEM tomography. The investigation of the synthesis mechanisms confirmed the major role of deprotonated carboxylic acid and of the heating rate to drive the cubic shape of nanoparticles and showed that the nanoplate formation would depend mainly on the nucleation step and possibly on the presence of a given ratio of oleic acid and deprotonated carboxylic acid.

Micronutrient deficiencies are a major public health problem. Beans are an important plant-based source of iron, zinc and copper, but their absorption is reduced in the presence of anti-nutrients such as phytates, polyphenols and tannins. Soaking and discarding the soaking water before cooking is unanimously recommended, but this can result in mineral loss. Data on the consequences for mineral bioaccessibility is still limited. This study aimed to evaluate iron, zinc and copper bioaccessibility in black beans cooked (regular pan, pressure cooker) with and without the soaking water. Minerals were quantified by ICP-MS, myo-inositol phosphates (InsP₅, InsP₆) by HPLC ion-pair chromatography, total polyphenols using Folin-Denis reagent and condensed tannins using Vanillin assay. Mineral bioaccessibility was determined by in vitro digestion and dialysis. All treatments resulted in a statistically significant reduction of total polyphenols (30%) and condensed tannins (20%). Only when discarding the soaking water a loss of iron (6%) and copper (30%) was observed, and InsP₆ was slightly decreased (7%) in one treatment. Bioaccessibility of iron and zinc were low (about 0.2% iron and 35% zinc), but copper presented high bioaccessibility (about 70%). Cooking beans under pressure without discarding the soaking water resulted in the highest bioaccessibility levels among all household procedures. Discarding the soaking water before cooking did not improve the nutritional quality of the beans.

We report the synthesis and characterization of Poly Methyl-Meth-Acrylate (PMMA)/Poly vinylalcohol (PVA) polymeric blend doped with different concentrations of Copper oxide (CuO) nanoparticles (NPs). The (PMMA-PVA)/CuO nanocomposite hybrid thin films (wt. % = 0%, 2%, 4%, 8%, and 16%) of CuO NPs are deposited on glass substrates via dip-coating technique. The transmittance (T%), reflectance (R%), the absorption coefficient (α), the optical constants [refractive index (n), extinction coefficient (k)], optical dielectric functions [ɛ',ɛ''] are investigated and interpreted. Tauc, Urbach, Spitzer-Fan, and Drude models are employed to calculate the optical bandgap energy (Eg) and the optoelectronic parameters of the nanocomposite thin films. The refractive index and optical bandgap energy of of (PMMA-PVA) polymeric thin film are found to be (1.5 to 1.85) and 4.101 eV, respectively. Incorporation of specific concentrations of CuO-NPs in (PMMA-PVA) polymeric thin films leads to a noticeable decrease in the optical bandgap energy and to an increase of the refractive index. Moreover, Fourier Transform Infrared Spectroscopy (FTIR) transmittance spectra are measured and analyzed for undoped and doped polymeric thin films to pinpoint the major vibrational modes in the spectral range (500 and 4000 cm-1), as well as, the nature of network bonding in both systems. Thermal stability of thin films is investigated by performing thermogravimetric analysis (TGA). The TGA thermograms confirm that both doped polymeric thin films are thermally stable at temperatures below 110°C which enables them to be attractive for a wide range of optical and optoelectronic applications. Our results indicate that optical, vibrational and thermal properties of both polymeric thin films can be tuned for specific applications by the appropriate corporation of particular concentrations of CuO-NPs.

Sentinel lymph node dissection (sLND) using a magnetometer and superparamagnetic iron oxide nanoparticles (SPIONs) as a tracer was successfully applied in prostate cancer (PCa). Radioisotope-guided sLND combined with extended pelvic LND (ePLND) achieved better node removal, increasing the number of affected nodes or the detection of sentinel lymph nodes outside the established ePLND template. We determined the diagnostic value of additional magnetometer-guided sLND after intraprostatic SPION-injection in high-risk PCa. This retrospective study included 104 high-risk PCa patients (PSA >20 ng/ml and/or Gleason score ≥8 and/or cT2c) from a prospective cohort who underwent radical prostatectomy with magnetometer-guided sLND and ePLND. The diagnostic accuracy of sLND was assessed using ePLND as a reference standard. Lymph node metastases were found in 61 of 104 patients (58.7%). sLND had a 100% diagnostic rate, 96.6% sensitivity, 95.6% specificity, 96.6% positive predictive value, 95.6% negative predictive value, 3.4% false negative rate, and 4.4% false positive rate (detecting lymph node metastases outside the ePLND template). These findings demonstrate the high sensitivity and additional diagnostic value of magnetometer-guided sLND, exceeding that of ePLND through the individualized extension of PLND or the detection of sentinel lymph nodes / lymph node metastases outside the established node template in high-risk PCa.

This paper presents a new scientific contribution on the two-dimensional (2-D) subdomain technique in polar coordinates taking into account the finite relative permeability of the ferromagnetic material. The constant relative permeability corresponds to linear part of the nonlinear B(H) curve. As in conventional technique, the method of separation of variables and the Fourier’s series are used for the resolution of magnetostatic Maxwell’s equations in each region. Although, the general solutions of magnetic field in the subdomains and boundary conditions (BCs) between regions are different in the conventional and proposed method. In this later, the magnetic field solution in each subdomain is a superposition of two magnetic quantities in the two directions (i.e., r- and Q-axis) and the BCs between two regions are also in both directions. For example, the scientific contribution has been applied to an air- or iron-cored coil supplied by a constant current. The distribution of local quantities (i.e., the magnetic vector potential and flux density) has been validated by a corresponding 2-D finite-element analysis (FEA). The obtained semi-analytical results are in very good agreement with those of numerical method.

The nitrogen-doped amorphous oxide semiconductor (AOS) thin film transistors (TFTs) with double-stacked channel layers (DSCL) were prepared and characterized. The DSCL structure composed of nitrogen-doped amorphous InGaZnO and InZnO films (a-IGZO:N/a-IZO:N or a-IZO:N/a-IGZO:N) made the corresponding TFT devices exhibit quite large field-effect mobility due to the existence of double conduction channels. Especially, the a-IZO:N/a-IGZO:N TFTs showed even better electrical performance (μ_FE = 15.0 cm²·V^-1·s^-1, SS = 0.5 V/dec, V_TH = 1.5 V, I_ON/I_OFF = 1.1×10⁸) and stability (V_TH shift of 1.5, -0.5, and -2.5 V for positive bias-stress, negative bias-stress and thermal stress tests, respectively) than the a-IGZO:N/a-IZO:N TFTs. Based on the X-ray photoemission spectroscopy measurements and energy band analysis, it was assumed that the optimized interface trap states, the less ambient gas adsorption, and the better suppression of oxygen vacancies in the a-IZO:N/a-IGZO:N hetero-structures might be responsible for the better behaviors of the corresponding TFTs.

An oxidation resistant coating on cemented tungsten carbides is characterised in this work. Cemented tungsten carbides (cWCs) are routinely used in mining and manufacturing but are also candidate materials for compact radiation shielding in fusion power generation. In both environments, cWCs will suffer significant degradation due to oxidation at relatively low temperatures. In a recent study, a Si-deposition coating method was demonstrated to improve the oxidation resistance of cWCs by up to a factor of 1,000. This work focusses on the growth kinetics, phase composition, and mechanical properties of these coatings. By combining quantitative X-ray diffraction, electron microscopy and nanoindentation, we show that the coating layer has a 20 % higher hardness than the substrate, which was explained on the basis of a previously-unknown presence of a fine distribution of very hard SiC laths. To interpret the coating stability, a coating growth map is developed. The map shows the structure is stable under a broad range of processing temperatures and composite compositions, demonstrating the potential application of these coatings in a variety of nuclear shielding cWCs.

Korenaga and coworkers present evidence to suggest that 4.3 billion years ago the Earth’s mantle was dry and water filled the ocean to twice its present volume.[2] CO₂ was constantly exhaled during the mafic to ultramafic volcanic activity associated with magmatic plumes that produced the thick, dense and relatively stable oceanic crust. In that setting two distinct major types of sub-marine hydrothermal vents were active: ~400 °C acidic springs whose effluents bore vast quantities of iron into the ocean, and ~120 °C, highly alkaline and reduced vents exhaling from the cooler, serpentinizing crust at some distance from the heads of the plumes. When encountering the alkaline effluents, the iron from the plume head vents precipitated out forming mounds likely surrounded by voluminous exhalative deposits similar to the banded iron formations known from the Archean. These mounds and the surrounding sediments likely comprising nanocrysts of the variable valence FeII/FeIII oxyhydroxide, green rust. The precipitation of green rust, along with subsidiary iron sulfides and minor concentrations of Ni, Co and Mo in the environment at the alkaline springs may have established both the key bio-syntonic disequilibria, and the means to properly make use of them – those needed to drive the essential inanimate-to-animate transitions that launched life. In the submarine alkaline vent model for the emergence of life specifically it is first suggested that the redox-flexible green rust microcrysts spontaneously formed precipitated barriers to the complete mixing of carbonic ocean and alkaline hydrothermal fluids, barriers that created and maintained steep ionic disequilibria; and second, that the hydrous interlayers of green rust acted as 'engines' that were powered by those ionic disequilibria and drove essential endergonic reactions. There, aided by sulfides and trace elements acting as catalytic promoters and electron transfer agents, nitrate could be reduced to ammonia and carbon dioxide to formate, while methane may have been oxidized to methyl and formyl groups. Acetate and higher carboxylic acids could then have been produced from these C1 molecules and aminated to amino acids, and thence oligomerized to offer peptide nests to phosphate and iron sulfides and secreted to form primitive amyloid-bounded structures, leading conceivably to protocells.

Lifespan extension was recently achieved in Caenorhabditis elegans nematodes by mitochondrial stress and mitophagy, triggered via iron depletion. Conversely in man, deficient mitophagy due to Pink1/Parkin mutations triggers iron accumulation in patient brain and limits survival. We now aimed to identify murine fibroblast factors, which adapt their mRNA expression to acute iron manipulation, relate to mitochondrial dysfunction and may influence survival. After iron depletion, expression of the plasma membrane receptor Tfrc with its activator Ireb2, the mitochondrial membrane transporter Abcb10, the heme-release factor Pgrmc1, the heme-degradation enzyme Hmox1, the heme-binding cholesterol metabolizer Cyp46a1, as well as the mitophagy regulators Pink1 and Parkin showed a negative correlation to iron levels. After iron overload, these factors did not change expression. Conversely, a positive correlation of mRNA levels with both conditions of iron availability was observed for the endosomal factors Slc11a2 and Steap2, as well as for the iron-sulfur-cluster (ISC)-containing factors Ppat, Bdh2 and Nthl1. Positive correlation only after iron depletion was observed for the iron export factor Slc40a1, mitochondrial iron transporters Slc25a28, Abcb7 and Abcb8, mitochondrial ISC-containing factors Glrx5, Nfu1, Bola1 and Abce1, cytosolic Aco1 and Tyw5, as well as nuclear Dna2, Elp3, Pold1 and Prim2. The latter are regulators of nucleotide synthesis and DNA quality control, which have known importance for growth and lifespan. The only Pink1-/- triggered transcript modulation was the reduced expression of the ISC-containing ribosomal factor Abce1. These mammalian findings support previous fly data that Pink1 influences co-translational quality control via Abce1, as well as mitophagy. Our findings provide the first systematic survey how iron dosage triggers homeostatic transcriptional regulations and elucidate how iron deprivation results in mitophagy.

The reaction kinetics of burnt lime (CaO) in contact with sea water has been elucidated and compared to its behaviour in fresh water. In the first minutes of contact between burnt lime and water, it "slaked" as CaO reacted with water to yield calcium hydroxide (Ca(OH)2). Subsequently, calcium hydroxide reacted with magnesium, sulphate and carbonate from the sea water to yield magnesium hydroxide (Mg(OH)2), calcium sulphate dihydrate (gypsum, CaSO4·2H2O) and calcium carbonate (CaCO3), respectively. In a closed system of 1% CaO in natural sea water (where the supply of sulphate, magnesium and carbonate is limited), more than 90% reacted within the first 5 hours. It is foreseen that in an open system, like a marine fjord, it will react even faster. The pH 8 of sea water close to the CaO particle surface will immediately increase to a theoretical value of about 12.5 but will, in an open system with large excess of sea water, rapidly fall back to pH 10.5 being equilibrium pH of magnesium hydroxide. This is further reduced to < 9 due to the common ion effect of dissolved magnesium in sea water and then be diluted to the sea water background pH, about 8. Field test dosing CaO particles to sea water showed that the pH of water between the particles stayed around 8.

Gymnema sylvestre is a pharmacological plant which has a rich source of bioactive compounds specifically gymnemic acid (GA) and phenolic compounds (PC) that used for pharmaceutical industries. Sources for naturally occurring bioactive compounds are limited, due to geographical and seasonal variations; on the other hand, it is commercially in demand. Biosynthesis of G. sylvestre phytochemicals through in vitro culture often enhanced by elicitation. The use of cell suspension cultures (CSC) has interested serious attention on the production of essential phytochemicals. The current study is aimed at improving the contents of GA and PC in G. sylvestre CSC using the copper oxide nanoparticles (CuO NPs). Callus was obtained on MS medium with 2.0 mg/L 2,4-dichlorophenoxyacetic acid (2,4-D), 0.1 mg/L kinetin (KIN), phytoagar (8.0 g/L), and sucrose (30 g/L). The above medium devoid of agar was used for the initiation of CSC. The CSC was treated with three levels of CuO NPs (1, 3 or 5 mg/L) to enhance the production of GA and PC. The greatest amount of GA (89.25 mg/g dry cell mass, DCM), total phenolic (245.10 mg/g), and flavonoid (4.57 mg/g) in CSC were achieved when G. sylvestre cells were treated for 48 h with 3 mg/L CuO NPs. Also, the biomedical potential (antioxidant, antidiabetic, anti-inflammatory, antibacterial, antifungal and anticancer activities) were also high in the CuO NPs (3 mg/L) treated CSC extracts of G. sylvestre. CuO NPs elicitation of CSC significantly increased production of GA (9-fold), and PC than non-elicited CSC in G. sylvestre.

Ghrelin and obestatin, two antagonist peptide hormones, are purportedly involved in stimulating appetite and controlling energy balance in humans. Serum ghrelin level is also associated with iron deficiency anemia (IDA), but no study has yet been made of the obestatin level in patients with IDA, even though both hormones are a single gene product. Therefore, the purpose of this investigation is to see whether there is a link between IDA and these two hormones among other hematological parameters in patients with IDA. To measure ghrelin and obestatin, human saliva and serum were collected from 30 women with IDA, aged 31.7 ± 10.7 years, and 30 control women, aged 30.2 ± 8.0 years, with repeated collection of samples over a period of 1 week and 1 month. Saliva and serum ghrelin levels were measured by ELISA. Serum hemoglobin, ferritin, hematocrit and total iron-binding capacity (TIBC) values were determined with an Olympus AU2700. Saliva and serum ghrelin and obestatin levels were significantly lower in the IDA group compared with controls; these levels increased slightly above baseline with iron treatment, but remained below the control values. Furthermore, and as expected, serum hemoglobin, ferritin, and hematocrit levels were significantly increased with iron treatment, while total iron-binding capacity decreased compared to baseline concentrations. The findings suggest that IDA might be linked to imbalance of circulating (serum) and non-circulating (saliva) ghrelin and obestatin levels. Decreased ghrelin and obestatin might destroy iron homeostasis through its effect on intestinal absorption. Measuring these hormone levels might be useful for monitoring the response to iron treatment. Also, serum and saliva levels for both hormones were well correlated. Thus, using saliva in place of serum for monitoring the two hormones should minimize inconvenience and patient discomfort.

The pollen content of honey samples collected in the years 2017 and 2019 from experimental apiaries of Melipona seminigra pernigra Moure & Kerr 1950 installed in campo rupestre on canga (CRC) vegetation of the Serra dos Carajás, southeastern Amazonia, was analyzed to understand the local variability of floral resources occurring on natural and disturbed areas. Around one hundred pollen types were identified mainly belonging to Fabaceae, Myrtaceae and Euphorbiaceae (31, 6 and 5 types, respectively). The N5 mine presented the highest pollen richness with 95 pollen types identified, almost twice of those identified in the other areas, including the better preserved ones. Eighty percent of the pollen types are rare with concentrations ≤ 2,000 pollen grains/10 g; the remaining types are the most abundant and frequent, and are considered the primary bee sources (PBS). PBS correspond mostly to native plants such as Tapirira guianensis Aubl., Protium spp., Aparisthmium cordatum (A.Juss.) Baill., Mimosa acutistipula var. ferrea Barneby, Periandra mediterrânea (Vell.) Taub., Miconia spp., Pleroma carajasense K.Rocha, Myrcia splendens (Sw.) DC., Serjania spp. and Solanum crinitum Lam. All pollen types were identified during both seasons, but higher pollen concentration are related to the dry period (June-September). The statistical analysis indicated that there was no significant difference in honey pollen data between the natural and disturbed areas since the plant species considered as PBS in this work are intensively used in revegetation of degraded area (RDA) processes by mining activities.

Graphene oxide (GO), nanographene oxide (nGO) and partially reduced graphene oxide (rGO) have been studied as possible foam stabilizing agents for CO₂ based enhanced oil recovery (EOR). GO was able to stabilize CO₂/synthetic sea water foams. rGO was not able to stabilize foams likely due to the high reduction degree of the material. Particle size had a strong influence on foamability and stability. GO hydrophilicity increased as the particle size decreased and no foams were created when particle size was below 1 µm (nGO). GO brine dispersions showed immediate gel formation, which improved foam stability. Particle growth due to layer stacking was also observed. This mechanism was detrimental for foam formation and stabilization. nGO dispersed in synthetic sea water rapidly formed hydrogels and was not filterable. This work indicates that the particles studied are not suitable for CO₂ EOR purposes.

The processing of alkanes (the main components of natural gas) for obtaining of industrially important chemical products is one of the most urgent environmental problems, because the major share of raw materials are burned in torches. Therefore, the main goal of the work is the development of catalysts and conditions for obtaining of important petrochemical products from light alkanes. For the preparation of catalysts, Mo, Cr and Ga oxide catalysts as well as catalysts based on heteropoly compounds, supported on natural materials were used. The catalysts were prepared by the capillary impregnation method and used in oxidative conversion in a flowing unit while varying the process conditions. It has been determined that 5 and 10% MoCrGa catalysts are optimal for obtaining of liquid and gaseous products, and 1% catalyst is more favorable for the synthesis of gaseous products. Supported catalysts from heteropoly acid Н₃PW₁₂O₄₀ are highly active in oxidative dehydrogenation and cracking processes, which are concurrent. High activity is caused by dispersity of catalysts, formation of crystal hydrates and amorphous phase of heteropoly acid in a condition of interaction with carrier. Maximum yield of C₂H₄ - 35.2% at 973 K, C₃H₆ – 20.0% and C₄H₈ – 14.3% at 773 К were observed.

Aiming to improve the flame retardancy performance of natural rubber (NR), we developed a novel flame retardant synergistic agent through grafting of MCM-41 to graphene oxide (GO)，named as GO-NH-MCM-41，as an assistant of intumescent flame retardants (IFR). The structure of GO-NH-MCM-41 was characterized by FTIR, TEM and SEM tests, which confirmed that a fine grafting had been applied between GO and MCM-41. The flame retardancy of NR/IFR/GO-NH-MCM-41 composites was evaluated by limited oxygen index (LOI), UL-94 and cone calorimeter test. The LOI value of NR/IFR/GO-NH-MCM-41 reached to 26.3%; the UL-94 ratings improved to V-0 rating. Moreover, the addition of GO-NH-MCM-41 obviously decreased the peak heat release rate (PHRR) and the total heat release (THR) of the natural rubber composites. And the addition of GO-NH-MCM-41 increased the thickness of char residue. The images of SEM indicated the char residue were more compact and continuous. The degradation of GO-NH-MCM-41 based NR composites completed with a mass loss of 35.57% at 600 ℃. The tensile strength and the elongation at break of NR/IFR/GO-NH-MCM-41 composites were 13.9 MPa and 496.7%, respectively. The results of rubber process analyzer (RPA) reached the maximum value, probably due to a better network of the fillers in the matrix.

Ultra-thin Fe–6.5wt.%Si ribbons with 35 μm in thickness were prepared by melt-spinning. The magnetic properties were investigated before and after annealing 1000 ºC. DC properties and low-frequency (400 Hz ~ 10 kHz) iron losses have significantly improved after heat treatment. A simplified formula based on Steinmetz law which can be used to predict the AC iron loss is presented. According to the results of some iron losses data, a simplified formula has been determined, and the extent of AC iron losses can be predicted. The results obtained from the formula predict AC iron loss to a good degree. The method developed in this work could be extended to other magnetic materials for predicting AC iron loss with greater ease.

Metal oxide based electrodes play a crucial role in various as a transparent conductive oxide (TCO). One of the metal oxides, nickel oxide is a promising electrical conductive material. Here, we display that incorporation of vanadium in NiO lattice significantly improve both electrical conductivity and hole extraction. Also, vanadium doped nickel oxide exhibits a lower crystalline size compared to pristine nickel oxide, which maintains the reduction of surface roughness. These results indicating that the vanadium is an excellent dopant for NiO.

We report the influence of ammonium hydroxide (NH4OH), as growth additive, on zinc oxide nanomaterial through the optical response obtained by photoluminescence (PL). A low-temperature hydrothermal process is employed for the growth of ZnO nanowires (NWs) on seedless Au surface. A more than two order of magnitude change in ZnO NW density is demonstrated via careful addition of NH4OH in the growth solution. Further, we show by systematic experimental study and PL characterization data that the addition of NH4OH can degrade the optical response of ZnO NWs produced. The increase of growth solution basicity with the addition of NH4OH may slowly degrade the optical response of NWs by slowly etching its surfaces, increasing the point defects in ZnO NWs. The present study demonstrates the importance of growth nutrients to obtain quality controlled density tunable ZnO NWs on seedless conducting substrates.

Zinc oxide is one of the most important semiconductor metal oxides and one of the most promising n-type materials, but its practical use is limited because of both its high thermal conductivity and its low electrical conductivity. Numerous studies have shown that doping with metals in ZnO structures leads to the modification of the band gap energy. In this work, Al-doped ZnO, Ni-doped ZnO, and undoped ZnO nanocrystalline powders were prepared by sol-gel method coupled with ultrasound irradiation. The doping concentration in ZnO was 1.0 at.% of Al and Ni. Influence of Al³⁺ and Ni²⁺ ions in the ZnO network are explored in this paper. X-ray Diffraction (XRD), Raman Spectroscopy, Nitrogen Adsorption (BET method), X-Ray Fluorescence (XRF) and Field Emission Scanning Electron Microscopy (FESEM) analyses demonstrated the incorporation of metal ions (aluminum and nickel) into the ZnO wurtzite structure. The crystallite size of the sample was decreased from 24.5 nm (ZnO) to 22.0 nm (ZnO-Al) and 21 nm (ZnO-Ni).

The aim of this study was to develop a novel nanostructured lipid carriers (NLCs) with hepatocytes targeting as carriers for the magnetic resonance imaging (MRI) contrast agent (i.e., magnetic nanostructured lipid carriers, MNLCs), and to evaluate the targeting ability of the MNLCs with T2-weighted MRI both in vitro and in vivo. Here, the galactose-octadecylamine (Gal-ODA) conjugates were synthesized by chemical coupling reaction between lactose acid (LA) and octadecylamine (ODA). Then the superparamagnetic iron oxide (SPIO) loaded nanostructured lipid carrier (conjugated by Gal-ODA, Gal-NLC-SPIO) was prepared by emulsification-ultrasonic method using monoglyceride as lipid materials. The Gal-NLC-SPIO with a diameter of about 50 nm could specifically internalize into LO2 (human hepatic cell line) cells. In vitro MRI results also proved the specific targeting ability of Gal-NLC-SPIO to LO2 cells. The in vivo MR imaging experiments using an orthotopic intrahepatic xenograft tumor model further validated the hepatocytes targeted effect of Gal-NLC-SPIO. The results of this study suggested that Gal-NLC-SPIO can be used as a contrast agent to aid in the diagnosis of hepatic diseases.

Keywords: iron deficiency anemia; IDA; anemia; knowledge; awareness.

Several observations have shown that patients with polycythemia have iron deficiency. Our objectives were to report the prevalence of iron deficiency, to evaluate the diagnostic performance of serum ferritin in polycythemia vera and to describe the mechanisms of this association. This is a retrospective descriptive and analytical study carried out in the internal medicine department of the Henri Mondor Hospital, Aurillac, France. The study involved 114 patients with polycythemia, followed in the department from January 1, 2010 to December 31, 2021. To evaluate the diagnostic performance, the JAK2 mutation was considered as the gold standard of diagnosis. Thirty-three patients had polycythemia vera and 76 patients had secondary polycythemia. The mean age of the patients was 61.79 years (±15.44) with a sex ratio of 4.43. The overall prevalence of iron deficiency was 21.05%. The prevalence was 53% in polycythemia vera group and 1.32% in secondary polycythemia group. The risk of iron deficiency was high in polycythemia vera (OR=115; 95% CI [14.4-918.2], p<0.000). The sensitivity and specificity of serum ferritin were 52.63% and 100% respectively. Assessment of iron deficiency should be part of the initial evaluation of polycythemia. The presence of iron deficiency is specific for polycythemia vera.

Abstract: Metal-air batteries provide a most promising battery technology given their outstanding potential energy densities, which are desirable for both stationary and mobile applications in a ‘beyond lithium-ion’ battery market. Silicon- and iron-air batteries underwent less research and development compared to lithium- and zinc-air batteries. Nevertheless, in the recent past, the two also-ran battery systems made considerable progress and attracted rising research interest due to the excellent resource-efficiency of silicon and iron. Silicon and iron are among the top five of the most abundant elements in the earth’s crust, which ensures almost infinite material supply of the anode materials, even for large scale applications. Furthermore, primary silicon-air batteries are set to provide one of the highest energy densities among all batteries, while iron-air batteries are frequently considered as a highly rechargeable system with decent performance characteristics. Considering fundamental aspects for the anode materials, i.e., the metal electrodes, in this review, we will first outline the challenges, which explicitly apply to silicon- and iron-air batteries and prevented them from a broad implementation so far. Afterwards, we provide an extensive literature survey regarding state-of-the-art experimental approaches, which are set to resolve the aforementioned challenges and might enable the introduction of silicon- and iron-air batteries into the battery market in the future.

Background: Iron chelation medications (desferoxamine, desferasirox, desferiprone) are used to manage iron overload. These medications are partially excreted via the kidneys, desferoxamine and desferiprone excretes primarily in the urine, and desferasirox had about 8% excreted in the urine. Their use in severe kidney disease and dialysis patients is caution as “avoided” concerning adverse effects; however, there are reports safe use. This manuscript reviews the literature in this population. Data Sources: Pubmed: desferasirox, deferiprone, deferoxamine, kidney disease, ESKD, Dialysis. Case reports and case series that described experiences with using iron chelation medications in ESKD patients are included. Data also gathered from reading-related sources. Results: This is a review of desferoxamine, desferasirox, and deferiprone use in kidney disease from 1976 to the present time. Table 1 provides a summary of findings. These are mostly reports and brief descriptions of the experiences used in severe kidney disease and dialysis, but lack of randomized control trials and small number of participants. Conclusions: Iron chelation medications are important for treating iron overload but concerns with adverse effects. Due to limited medications available to treat iron overload in patients with severe kidney disease, their safe use has been reporting in the literature. This is an area that warrants further research.

In this experimental work, pure nickel oxide and Al-doped NiO thin films have successfully been elaborated onto glass substrates by solar spray pyrolysis technique. The substrates were heated at around 450°C using a solar heater (furnace). The structural, optical and electrical properties of the elaborated Al-doped films have been studied at different atomic percentage ratios (0, 0.5, 1, 1.5 and 2 at. %). The results of Al-doped NiO films XRD patterns were, the formation of (NiO) phase under a cubic crystalline structure (polycrystalline) with a strong favored orientation along (111) plane were noticed at all sprayed films. When Al doping ratio reaches 1 at.%, an growth in crystallite size over 31.9 nm was obtained denoting the nano-structure of the product, which confirmed by SEM images. In addition, aluminum oxide Al₂O₃ was clearly observed at 1.5 at.% Al ratio. Otherwise, all thin films have a good optical transmission in the visible region of about 65%, the optical band gap energy decreased from 3.69 to 3.64 eV with increasing Al doping ratio. It is shown that the layer deposited with 0.5 at.% has less disorder with few defects. The investigation on electrical properties of elaborated thin films confirmed that the conductivity of NiO films was improved, after doping them with Al which affirms their p-type character of semiconductor. However, an addition of an excessive quantity of Al content causes the formation of Al₂O₃ which leads to a decrease in the conductivity. It is worth mentioning that the Al content of 0.5 at.% is the optimum ratio in terms of electrical conductivity and formation defect. Al-doped NiO can be used in various optoelectronic devices due to its good transparency and high electrical conductivity.

Catalyst material plays a pivotal role in the pharmaceutical industry process. Among them, Friedel-Craft acylation reaction is a well-known reaction to synthesis acetophenone derivatives. However, Friedel-Craft acylation mostly used acetyl chloride as starting material with Lewis acid as homogeneous catalyst, which is nonenvironmental friendly process. In this work, a simple and efficient Friedel-Craft acylation reaction is reported by using the palladium oxide doped on activated bentonite (PdOAB) as the heterogeneous catalyst. The PdOAB catalyst material was characterized with scanning electron microscopy-energy dispersive X-ray (SEM-EDX), nitrogen isotherm adsorption, Fourier transform infrared (FTIR), X-ray powder diffraction (XRD), and thermogravimetric-differential thermal analysis (TG-DTA). The acetophenone derivatives with R = -H, -Cl, -CH₃, -OCH₃, -OH and -NH₂ at para position were successfully synthesized from its corresponding aromatic compounds with glacial acetic acid in 86.6, 7.9, 91.7, 86.6, 82.7, and 78.9% yield, respectively. Therefore, a green method was established because the byproduct is water and the catalyst material can be recovered. Furthermore, the substituent (σ) constants were obtained by using Hammet equation, and the catalysis mechanism has been proposed.

Purpose: To correlate outflow function and outflow tract vessel diameter changes induced by nitric oxide (NO). Methods: In a porcine anterior segment perfusion model, the effects of a nitric oxide donor (100 µM DETA-NO) on outflow facility were compared to controls (n=8 per group) with trabecular meshwork (TM) and after circumferential ab interno trabeculectomy (AIT). Outflow structures were assessed with spectral domain optical coherence tomography (SD-OCT) before and after NO, or an NO synthase inhibitor (100 µM L-NAME) and the vasoconstrictor, endothelin-1 (100 pg/mL ET-1). Scans were processed with a custom macro script and aligned for automated reslicing and quantification of cross-sectional outflow tract areas (CSA). Results: The facility increased after DETA-NO (0.189±0.081 μL/min·mmHg, p=0.034) and AIT (0.251±0.094 μL/min·mmHg, p=0.009), respectively. Even after AIT, DETA-NO increased the facility by 61.5% (0.190±0.074 μL/min·mmHg, p=0.023) and CSA by 13.9% (p<0.001). L-NAME + ET-1 decreased CSA by -8.6% (p<0.001). NO increased the diameter of focal constrictions 5.0±3.8 fold. Conclusions: NO can dilate vessels of the distal outflow tract and increase outflow facility in a TM-independent fashion. There are short, focally constricting vessel sections that display large diameter changes and may have a substantial impact on outflow.

In recent years, numerous topologies of single phase and three phase Field Excited Flux-Switching Machine (FEFSM) have been developed for several applications. Comparative study of three types of single-phase low-priced Field Excited Flux-Switching Machine (FEFSM) is presented in this paper. Both the conventional 8S/4P sub-part rotor design and 6S/3P salient rotor design have an overlapped winding arrangements between armature coil and field excitation coil that depicts high copper losses as well as results in increased size of motor. Additionally, FEFSM with salient structure of the rotor have high flux strength in the stator-core that has much impact on high iron losses. Copper consumption and iron loss being a crucial proportion in total machine losses. Therefore a novel topology of single phase modular rotor field excited FSM with 8S/6P configuration is proposed, which enable non-overlap arrangement between armature coil and FEC winding that facilitates devaluation in the copper losses. The proposed modular rotor design acquires reduced iron losses as well as reduced active rotor mass comparatively to conventional rotor design. It is very persuasive to analyze the best range of speed for these rotors to avoid cracks and deformation, the maximum tensile strength (can be measured with principal stress in research) of the rotor analysis is conducted using JMAG. A deterministic optimization technique is used to enhance the performance of 8S/6P modular rotor design. The electromagnetic performance of conventional sub-part rotor design, F1-A3-3P design and proposed novel-modular rotor design are analyzed by 3D-Finite Element Analysis (3D-FEA), includes flux linkage, flux distribution, flux strength, back-EMF, cogging torque, torque characteristics, iron losses and efficiency.

Nitrogen (N) is an essential nutrient and plays an important role in plant growth and physiology. In addition, N is also the limiting nutrient in most terrestrial ecosystems. The increasing use of N fertilizers increases agricultural production, but also has negative impacts on biodiversity, water quality and increases emissions of greenhouse gases such as nitrogen oxides (NOx) and nitrous oxide (N2O) into the atmosphere. N2O is a strong greenhouse gas and the product of microbial transformation processes of N introduced into soil and groundwater (nitrification and denitrification). The production of N2O in soils is highly dependent on oxygen and water content, soil temperature and texture and the available amount of reactive nitrogen (NO3- or NH4+). In agricultural soils, N2O emissions are also influenced by the type of fertilizer used, crops grown, soil pH and NO3- concentration. Refined forms of land management, such as the cultivation of legumes, can reduce the use of fertilizers and thus also the emission of N2O. Legumes can use symbiotic nodule bacteria (rhizobia) to bind atmospheric N2 and make it available to the plant. Non-symbiotic soil microorganisms such as cyanobacteria or other heterotrophic and autotrophic prokaryotes are also able to fix N2. Furthermore, the N2-fixing enzyme nitrogenase, which is specific for most organisms, is not specific for other N2 compounds, especially N2O. To study the N2 and N2O fixation potential of soils and legumes, experiments with isotope-enriched N-gases (100 mol% 15N2 and 15N2O) were performed. Three different soil types (forest, meadow and wetland) as well as legume plants inoculated with rhizobia bacteria (Rhizobium leucaneae) (Leucaena leucocephala) were incubated in microcosms with different mixing ratios of N2 and N2O over a period of one week. The measured 15N enrichment was then used to determine the biological uptake rates. Both in plants and in soils admixtures of up to 40% N2O had no influence on the N2 fixation rate. N2 uptake rates were 1.2 ± 0.4 ug N gdw-1 d- 1in forest and grassland soils and 3.9 ± 1.2 ug N gdw-1 d- 1 in wetland soils. In contrast, the N2 fixation rates of leguminous plants were significantly higher (130 ± 40 ug N gdw-1 d- 1), with the highest accumulation not in root nodules but in the roots. In both plants and soil, the N2O fixation of 0.2 ± 0.1 ug N gdw-1 d- 1 could only be measured from a concentration of 4 vol%. The results indicate that both soils and legumes have a high potential to bind atmospheric nitrogen in the form of both N2 but not N2O. The fate of nitrogen in soil needs to be further investigated. N2 fixation seems to play an important role in wetland soils. Legumes in particular have the potential for NH4+ input and N2O reduction, as most of the solid nitrogen has been transferred to the roots, which can contribute significantly to soil nutrient input.

Abstract: COVID-19 in 2020 brought challenges to the Brazilian public health system with an emerging virus with respiratory contagion called SARS-CoV-2. There are few studies in Brazil and in some countries, on the increased incidence of certain viral respiratory infections, includ-ing H1N1 and coronavirus and their association with low levels of vitamin D, zinc and iron. The aim of this study was to demonstrate that the deficit of vitamin D, zinc and iron has an impact on the infectious process of patients with COVID-19 and to establish new forms of prevention for the worsening of COVID-19 in the human body. Data were collected from medical records and test results from patients being followed up during the treatment period for COVID-19. Patients with low blood levels of vitamin D, zinc and iron during the treatment period of COVID-19 had a higher percentage of worsening and complications requiring hospitalization in intensive care beds. The ingestion of vitamin D, zinc and iron in the treatment period of patients with COVID-19 in addition to being an immunological protector against SARS-CoV-2 and alleviating the process of worsening the disease can also act as a biomarker in cases of this disease.

Fall armyworm Spodoptera frugiperda (J.E. Smith, 1797) is a major pest of corn, rice, and sorghum among other crops usually controlled using synthetic or biological insecticides. Currently, the new invention of nanotechnology is taking root in the agricultural industry as an alternative source of pest management that is target-specific, safe, and efficient. This study sought to determine the efficacy of commercial Zinc Oxide (ZnO) nanoparticles (NPs) towards S. frugiperda under labora-tory conditions. ZnO NPs were diluted into different concentrations (100- 500ppm), where the baby corn used to feed the S. frugiperda larvae was dipped. The development of the insect feeding on food dipped in ZnO solution was significantly (p<0.05) affected, and the number of days that the insect took to complete its life cycle had a significant difference compared to the control. There was a significant difference in the adults’ emergence at all the concentrations of ZnO NPs compared to the control, with over 90% of the eggs successfully going through the cycle until adult emergence. Additionally, several malformations were observed throughout the lifecycle of the insect. Also, the fecundity of the females was greatly affected. The findings of this study suggest the possibility of exploitation of ZnO nanoparticles not only to eradicate S. frugiperda but to significantly reduce their population in the ecosystem through deformations, reduced fecundity, reduced oviposition, and hatchability of eggs. It will be a valuable tool in integrated pest management regimens.

Magnetic iron oxide particles are used for in vitro diagnostics for nearly 40 years. Due to their unique physical, chemical, thermal and mechanical properties, as well as biocompatibility and low toxicity in the human body, iron oxide nanoparticles have been used in many biomedical applications, such as contrast agents for magnetic resonance imaging, carriers for controlled drug delivery and immunoassays, but also in magnetic hyperthermia. Our aim is to investigate the effect of pressure and temperature on the structural, thermal and magnetic properties of iron oxide nanomaterials prepared by hydrothermal synthesis. Iron oxide nanoparticles were synthesized at temperatures of 100-200°C and pressures of 20-1000 bar. It has been found that pressure influences the type of iron oxide crystalline phase. Thus, for lower pressure values (< 100 bar), iron oxide is predominantly formed as hematite, while at pressures > 100 bar, the major crystalline phase is goethite. The complex thermal analysis revealed the polymorphic changes of iron oxides at different temperatures. The existence of specific magnetite and hematite phases in all thermally treated samples are evidenced through the specific Verwey and Morin transitions highlighted by ZFC-FC (Zero Field Cooled-Field Cooled) measurements, whereas their relative content is precisely provided by Mössbauer spectroscopy.

Hybrid materials of conjugated polymer and titanium(IV) oxide have attracted considerable attention concerning potential benefits, including (i) efficient exploitation of visible light, (ii) high adsorption capacity for organic contaminants, (iii) effective charge carriers separation. The new class of the photocatalysts is promising for the removal of environmental pollutants in both aqueous and gaseous phases. For the first time, in this study, the PANI/TiO₂ hybrid composite was used for the degradation of phenol in water and toluene in the gas phase. Polyaniline-TiO₂ was prepared by in-situ polymerization of aniline on the TiO₂ surface. The obtained hybrid material was characterized by diffuse reflectance spectroscopy (DR/UV-Vis), X-ray diffraction (XRD), fast-Fourier transformation spectroscopy (FTIR), photoluminescence (PL) spectroscopy, microscopy analysis (SEM/TEM) and thermogravimetric analysis (TGA). An insight into the mechanism was shown based on the photodegradation analysis of charge carriers scavengers. Polyaniline is an efficient TiO2 photosensitizer for photodegradation in visible light (λ> 420 nm). The trapping experiments revealed that mainly h+ and ˙OH were reactive oxygen species responsible for phenol degradation. Furthermore, the PANI-TiO₂ hybrid nanocomposite was used in gypsum plaster to study the self-cleaning properties of the obtained building material. The effect of PANI-TiO₂ content on hydrophilic/hydrophobic properties and crystallographic structure of gypsum was studied. The obtained PANI-TiO₂ modified gypsum plaster had improved photocatalytic activity in the reaction of toluene degradation under Vis light.

Nuclear receptor coactivator 4 (NCOA4) is a selective cargo receptor that mediates the autophagic degradation of ferritin (“ferritinophagy”), the cytosolic iron storage complex. NCOA4-mediated ferritinophagy maintains intracellular iron homeostasis by facilitating ferritin iron storage or release according to demand. Ferritinophagy is involved in iron-dependent physiological processes such as erythropoiesis, where NCOA4 mediates ferritin iron release for mitochondrial heme synthesis. Recently, ferritinophagy has been shown to regulate ferroptosis, a newly described form of iron-dependent cell death mediated by excess lipid peroxidation. Dysregulation of iron metabolism and ferroptosis have been described in neurodegeneration, cancer, and infection, but little is known about the role of ferritinophagy in the pathogenesis of these diseases. Here, we will review the biochemical regulation of NCOA4, its contribution to physiological processes and its role in disease. Finally, we will discuss the potential of activating or inhibiting ferritinophagy and ferroptosis for therapeutic purposes.

Immunosensors have been widely developed to use antibodies to detect a pathogen of interest; it is interesting to look at the effect of nonspecific antibody binding to E. coli using electrochemical methods. IgG antibody not specific to E. coli O157:H7 was crosslinked onto a screen-printed carbon electrode. The presence of E. coli at 4, 4 × 10², 4 × 10⁵, and 4 × 10⁸ CFU/mL on the electrode surface was detected via linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS). Current transfer at both electrodes was reduced as the concentration of bacteria increased; however, the calibration of number of cells to decreased current was nonlinear for IgG-modified electrodes. The nonlinearity is confirmed by EIS measurements which showed highest impedance at 4 CFU/mL E. coli when impedance should be the lowest. FESEM images showed higher binding of cells when IgG is present compared to electrodes with reduced graphene oxide (rGO) alone. Electrodes with rGO alone show less attachment of E. coli, with EIS showing a linear calibration profile, while LSV shows not much difference in current values for all concentrations aside from the highest concentration. These results suggest that nonspecific binding can provide false signals in electrochemical measurements, and it is crucial to provide proper controls.

Water deficit caused by drought is a significant threat to crop growth and production. Nitric oxide (NO), a water- and lipid-soluble free radical, plays an important role in cytoprotection. Apart from a few studies supporting the role of NO in drought responses, little is known about this pivotal molecular amendment in the regulation of abiotic stress signaling. In this review, we highlight the knowledge gaps in NO roles under drought stress and the technical challenges underlying NO detection and measurements, and we provide recommendations regarding potential avenues for future investigation. The modulation of NO production to alleviate abiotic stress disturbances in higher plants highlights the potential of genetic manipulation to influence NO metabolism as a tool with which plant fitness can be improved under adverse growth conditions.

The use of cobalt-iron (VaCoFe) core is investigated as an alternative to silicon-iron (FeSi) on the design of interior permanent magnet synchronous motors (IPMSM). A spoke-type IPMSM geometry is optimized considering FeSi and VaCoFe cores for a torque range up to 40 N.m, providing a general comparative analysis between materials, considering the application of a 4-motor competition vehicle’s powertrain. A genetic optimization algorithm is applied over a hybrid analytical/finite-element model of the motor to provide sufficiently accurate electromagnetic and thermal results within a feasible time. VaCoFe can result in an estimated increase of up to 5 % in efficiency for the same torque, or up to 64 % torque increase for the same efficiency level. After optimization, and using a detailed time-dependent model, a potential 3.2 % increase in efficiency, a core weight reduction of 4.1 %, and a decrease of 9.6 % in the motor’s core volume was found for the VaCoFe at 20 Nm. In addition, for the same motor volume, the VaCoFe allows an increase of 51.9 % of torque with an increase of 1.1 % of efficiency, when compared with FeSi.

Background: Essential hypertension is a major public health associated with increase pressure on the vascular walls and red blood cells (RBCs). In the present work, osmotic fragility (OF) of RBCs was reexamined in the means of its correlation with two risk factor; iron status and lipid profile. Experimental: OF, iron status parameters, and lipid profile components were measured in 60 patients and compared with the results of 30 controls. Results: The results showed a significant increase in all iron indices of hypertensive patients in comparing with healthy control group except TIBC, UIBC, and transferrin concentrations, which decrease in these patients in comparing with control group. Serum TGs, total cholesterol, VLDLc, and LDLc were increased while there is no significant in serum HDLc in patients to comparing with control group. There is no significant change in OF between patients and controls where p=0.173. The iron status parameters and lipid profile components were dependent on sex and smoking state. Hemoglobin and PCV were correlated significantly with total cholesterol and LDLc. Transferrin saturation showed a positive correlation with cholesterol, LDLc, and TGs, but negatively correlated with HDL_c. No significant correlation between all the measured parameters and OF in HT patients. There is a significant correlation between serum ferritin and systolic BP and between Hb and systolic BP. Conclusion: No significant effect on the OF in HT patients. HT patients have elevated level of iron parameters in comparing with controls. OD has no correlation with iron status parameters or with lipid profile components.

The welding performance of shipbuilding steel under large heat input could be improved greatly by the Mg addition to the steel, but the impact toughness of the HAZ is not stable. According to the three different thickness steel plates obtained in the industrial experiment, the large heat input welding was carried out by different heat input, and the impact toughness analysis, impact fracture analysis, metallographic microstructure analysis and inclusions analysis were carried out. The results showed that, the HAZ of three kinds of thickness plates induced a lot of IAF, with Mg addition, the inclusion dimension had been reduced effectively, and the IAF induced ability of the inclusions had also been improved. The difference of HAZ impact toughness with different welding heat input and different impact temperature is significant, in consideration of the influence of welding heat input and metallographic microstructure on impact toughness of HAZ, the welding heat load had far greater effect than metallographic microstructure on ductile-brittle transition temperature. At the same time, if the original metallographic microstructure of steel was coarse, the pinning effect of the inclusions would be reduced significantly, and the microstructure of HAZ would be coarsened and the impact toughness of HAZ would be decreased, so there is a certain matching relationship between the metallographic microstructure and the inclusion dimension.

Commercially pure (c.p.) iron powders with a deliberate high degree of oxidation were consolidated by medium-frequency electrical resistance sintering (MF-ERS). This is a consolidation technique where pressure, and heat coming from a low-voltage and high-intensity electrical current, are simultaneously applied to a powder mass. In this work, the achieved densification rate is interpreted according to a qualitative microscopic model, based on the compacts global porosity and electrical resistance evolution. The effect of current intensity and sintering time on compacts was studied on the basis of micrographs revealing the porosity distribution inside the sintered compact. The microstructural characteristics of compacts consolidated by the traditional cold-press and furnace-sinter powder metallurgy route are compared with results of MF-ERS consolidation. The goodness of MF-ERS versus the problems of conventional sintering when working with oxidized powders is analyzed. The electrical consolidation allows to obtain higher densifications than the traditional route under non-reducing atmospheres.

Stem cells derived from dental tissues—dental stem cells—are flavored due to their easy acquisition. Among them, dental pulp stem cells (DPSCs) extracted from the dental pulp have many advantages such as high proliferation and highly purified population. Although their ability for neurogenic differentiation has been highlighted and neurogenic differentiation using electrospun nanofibers (NFs) has been performed, graphene-incorporated NFs have never been applied for DPSC neurogenic differentiation. Here reduced graphene oxide (RGO)-polycaprolactone (PCL) hybrid electrospun NFs were developed and applied for enhanced neurogenesis of DPSCs. First, RGO-PCL NFs were fabricated by electrospinning with incorporation of RGO and alignments, and their chemical and morphological characteristics were evaluated. Furthermore, in vitro NF properties such as influence on the cellular alignments and cell viability of DPSCs were also analyzed. The influences of NFs on DPSCs neurogenesis was also analyzed. The results confirmed that an appropriate concentration of RGO promoted better DPSC neurogenesis. Furthermore, the use of random NFs facilitated contiguous junctions of differentiated cells, whereas the use of aligned NFs facilitated aligned junction of differentiated cells along the direction of NF alignments. Our findings showed that RGO-PCL NFs can be a useful tool for DPSC neurogenesis, which will help regeneration in neurodegenerative and neurodefective diseases.

The development of sensors for monitoring Carbon Monoxide (CO) in a large range of temperature is of crucial importance in areas as monitoring of industrial processes or personal tracking using smart objects. Devices integrating GaN/Ga₂O₃ core/shell nanowires (NWs) is a promising solution allowing combining the high sensitivity of the electronic properties to the states of GaN-core surface; and the high sensitivity to CO of Ga₂O₃-shell. Because the performances of sensors primarily depend on the material properties composing the active layer of the device, it is essential to control these properties and in first time its synthesis. In this work, we investigate the synthesis of GaN/Ga₂O₃ core-shell NWs with a special focus on the formation of the shell. The GaN NWs grown by Plasma-assisted molecular beam epitaxy, are post-treated following thermal oxidation to form Ga₂O₃-shell surrounding the GaN-core. We establish that the Ga₂O₃-shell thickness can be modulated from 1 up to 14 nm by changing the oxidation conditions, and follows the diffuse-controlled reaction. By combining XRD-STEM and EDX analysis, we also demonstrate that the oxide shell formed by thermal oxidation is crystalline and presents the β-Ga₂O₃ crystalline phase, and is synthesized in epitaxial relationship with the GaN-core.

1) Background: we have evaluated the antihypertensive effect of several flavonoid extracts in a rat model of arterial hypertension caused by chronic administration (6 weeks) of the nitric oxide synthesis inhibitor, L-NAME. 2) Methods: Sprague Dawley rats received L-NAME alone or L-NAME plus flavonoid-rich vegetal extracts (Lemon, Grapefruit + Bitter Orange, and Cocoa) or purified flavonoids (Apigenin and Diosmin) for 6 weeks. 3) Results: L-NAME treatment resulted in a marked elevation of blood pressure, and treatment with Apigenin, Lemon Extract, and Grapefruit + Bitter Orange extracts significantly reduced the elevated blood pressure of these animals. Apigenin and some of these flavonoids also ameliorated nitric oxide-dependent and independent aortic vasodilation and elevated nitrite urinary excretion. End-organ abnormalities such as cardiac infarcts, hyaline arteriopathy and fibrinoid necrosis in coronary arteries and aorta were improved by these treatments, reducing the end-organ vascular damage. 4) Conclusions: the flavonoids included in this study, specially apigenin, may be used as functional food ingredients with potential therapeutic benefit in arterial hypertension.

Beta thalassemia major (β-TM) disorder characterized by the lack, or severe reduction in the production of hemoglobin β-globin chains. The standard protocol for the management of β-TM is blood transfusion and iron chelation therapy to reduce the iron overload state. The present study aimed to investigate the relationships between two iron regulatory hormones, hepcidin (HEPC) and erythroferrone (ERFE) levels and iron status parameters (ISPs) in Iraqi patients with β-TM. ISPs and hormones were measured in sixty patients and compared with thirty healthy controls. The results indicated significant changes in different iron status parameters, while ferritin (FRT) with the ~11 fold increase showed the most change. Significant reduction in HEPC and increase in ERFE levels were detected in patients as compared to the control group, while no direct correlation was identified with the other measured ISPs. Receiver operating characteristic (ROC) analysis showed that the z-score of the composite of ERFE+FRT has a full diagnostic ability for β-TM. In conclusion, our finding indicated the correlation between different ISPs, FRT as the leading predictor of iron overload and tow main iron regulatory hormones.