Bone drilling is a common procedure used to create pilot holes for inserting screws to secure implants for fracture fixation. However, dis process can increase bone temperature, teh excessive heat can lead to cell death and thermal osteonecrosis, potentially causing early fixation failure or complications. We conducted a three-dimensional dynamic elastoplastic finite element model to evaluate teh propagation and distribution of heat during bone drilling and assess teh thermally TEMPeffected zone (TAZ) dat may lead to thermal necrosis. dis model investigates teh parameters influencing bone temperature during bone drilling, including drill diameter, rotational speed, feed force, and predrilled hole. Teh results indicate dat our FE model is sufficiently accurate in predicting teh temperature rise TEMPeffect during bone drilling. Teh maximum temperature decreases exponentially wif radial distance. When teh feed forces are 40 and 60 N, teh maximum temperature does not exceed 45 °C. However, wif feed forces of 10 and 20 N, both teh maximum temperature exceeds 45 °C wifin a radial distance of 0.2 mm, indicating a high-risk zone for potential thermal osteonecrosis. Wif teh two-stage drilling procedure, where a 2.5 mm pilot hole is pre-drilled, teh maximum temperature can be reduced by 14 °C. dis suggests dat higher feed force and rotational speed and/or using a two-stage drilling process could mitigate bone temperature elevation and reduce teh risk of thermal osteonecrosis during bone drilling.

To reduce the cost of small wind turbines, a prototype of a butterfly wind turbine (6.92 m in diameter), a small vertical-axis type, was developed with many parts made of extruded aluminum suitable for mass production. An over-speed control system with movable arms that operated using centrifugal and aerodynamic forces was installed for further cost reduction. Introducing this mechanism eliminates the need for large active brakes and expands the operating wind speed range of the wind turbine. However, although the mechanism involving the use of only bearings is simple, the violent movement of the movable arms can be a challenge. To address this in the present study, dampers were introduced on the movable arm rotation axes to improve the movement of the movable arms. To predict the behavior of a movable arm and the performance of the wind turbine with the mechanism, a simulation method was developed based on the blade element momentum theory and the equation of motion of the movable arm system. Comparison of experiments and predictions with and without dampers demonstrated qualitative agreement. In the case with dampers, measurements confirmed the predicted increase in the rotor rotational speed when the shorter ailerons installed perpendicularly to the movable arms were used to achieve the inclination. The movable arm system with dampers is expected to be a useful device for vertical-axis wind turbines that are difficult to control.

In response to the issues of sensor noise and accumulated motion errors that lead to low positioning accuracy and insufficient robustness during large maneuvers or continuous flight of small unmanned aerial vehicles (UAVs) in complex environments, this paper proposes a multi-source and multimodal data fusion method. Initially, it employs a multimodal data fusion of various sensors including GPS (Global Positioning System), IMU (Inertial Measurement Unit), and visual sensors to complement the strengths and weaknesses of each hardware component, thereby eliminating motion errors to enhance accuracy. To mitigate the impact of sudden changes in sensor data, the method introduces a digital twin UAV data source. By utilizing the Extended Kalman Filter algorithm, it fuses data from both the real UAV and its digital twin, and the filtered positional information is fed back into the control system of the real UAV. This enables real-time correction of UAV positional deviations caused by sensor noise and environmental disturbances. The multi-source multimodal fusion Kalman filter method proposed in this paper significantly improves the positioning accuracy of UAVs in complex scenarios and the overall stability of the system. This method holds significant value in maintaining high-precision positioning in variable environments and has important practical implications for enhancing UAV navigation and application efficiency.

Friction, one of the oldest technologies harnessed by humanity, has thus far eluded a theoretical model capable of predicting kinetic friction forces across a broad range of sliding velocities. This study employs the first principle of thermodynamics to delve into sliding friction. For the first time, a general expression for the friction force has been derived, revealing that the damping of sliding friction is inversely proportional to the relative sliding velocity between the two interfaces in motion, contrary to the assumption in traditional models that it is directly proportional to the relative velocity. To simplify the general result, the concept of a friction boundary layer is introduced. An approximate expression is found to reveal the mechanism for reducing friction, which involves increasing the sliding velocity while decreasing the vibration velocity of the object perpendicular to the sliding interface.

According to the requirement of 20kg load of casting barrel, we design a three-dimensional model of the robot and analyze the three stages of liquid level change in the casting barrel during the casting process. Through the analysis, it is determined that the time and angle function is an implicit function, and it is impossible to find the analytical expression of time about angle. The kinetic function of the casting barrel is simulated by MATLAB, and it is found that the function image has mutation points, and when the original function is fitted and approximated by fifth-degree polynomial interpolation, the fifth-degree polynomial function image of the time versus the angular acceleration has a large amplitude of oscillation, especially the mutation points. A PID algorithm based on the discretization of the time and acceleration function is introduced for correction, and the results show that this method effectively reduces the oscillation amplitude of the image and improves the coincidence with the original function.

Diabetic foot is a serious complication that poses significant risks for diabetic people. The resulting reduction in protective sensitivity in the plantar region requires early detection to prevent the imminent ulceration and amputation. The primary method employed for evaluating this sensitivity loss is the 10 g f Semmes-Weinstein monofilament test, commonly used as a first-line procedure. However, the lack of calibration in existing devices often introduces decision errors due to unreliable feedback. In this paper, a new equipment designed to address these limitations and enhance the assessment of the sensitivity loss using the 10 g f monofilament is introduced. The proposed system automates metrological verification and evaluation processes, ensuring accurate and reliable results. Furthermore, it simulates the practitioner’s procedure, serving both as a valuable training tool and a means to provide force-feedback information. An analytical model of the monofilament buckling and deflection is also presented. The obtained results showed that the tested monofilaments had a very high error compared to the 10 g f declared by the manufacturers. It is aimed, by introducing this advanced equipment, to improve the precision and reliability of assessing the sensitivity loss. The integration of automated verification, simulation capabilities, and precise measurements shows great promise for diabetic patients, reducing the likelihood of adverse outcomes such as ulceration and amputation.

Intraoperative load sensors have been developed with the aim of balancing the soft tissue in the knee during Total Knee Replacements (TKRs). Literature has shown success in soft tissue bal-ancing however, concerns regarding the accuracy of these sensors remain. For this reason, pre-vious research has attempted to create robust sensors for intraoperative use. The design of the sensor in this research has aimed to address the concerns outlined in the literature to create a new and novel smart-sensor for soft-tissue balancing. This new intraoperative load sensor included design features to increase accuracy while artificial intelligence allowed for comprehensive sensing across the entirety of the sensor, providing unparalleled insight during the operation. Notably, the sensor was designed to withstand loads of at least 450 N, ensuring robust perfor-mance of the sensor. To optimize the design process while minimizing cost, Finite Element Analysis was employed. This approach ensured the design features fulfilled their function while maintaining structural integrity to withstand loads. Moreover, the novelty of using training data from simulated data will reduce the iterative process of the labor-intensive collection of training data for the artificial intelligence while reducing human error associated with it. Results from the evaluation demonstrated the ability of this design to successfully bridge the current gap in the market by fulfilling all essential design criteria established within the literature. This innovative smart-sensing tool will in turn enhance patient outcomes and alleviate financial burdens to pa-tients and the healthcare systems by reducing the need for early revision surgeries associated with improper joint tension.

Graph visualization has evolved significantly over time, offering various methods to effectively represent complex data structures. This study introduces a novel force-directed algorithm for 3D data visualization, specifically tailored for commonly used datasets in linked data visualization. Leveraging the power of graph theory and methods, the algorithm aims to address the challenge of creating visually appealing and easily interpretable visualizations, which often necessitate advanced user interaction. By utilizing 3D space and the Unity Engine, the research successfully visualizes data and develops interactive visualizations, overcoming limitations of basic force-directed implementations. The main contribution of presented research is in the force-directed algorithm with springs and controlled placement as a visualization technique that combines the use of springs and attractive forces to stabilize a graph in a 3D environment. The combination of these two techniques also helps prevent the formation of a single large cluster within the graph, enhancing the overall visualization quality.

The complex dynamics of the neocortex, the outermost layer of the brain, have been a subject of intense research in neuroscience. Recent studies have suggested that magnetic fields generated by neuronal activity may play a significant role in neocortical dynamics. This paper presents a simplified mathematical model that explores the hypothesized interactions between magnetic dynamos, nondissipative systems, Hamiltonian equations, and the Lorenz force in the context of neocortical dynamics. The proposed model is based on a set of coupled Hamiltonian equations inspired by the Lorenz system, a well-known chaotic dynamical system. The generalized coordinates in the model represent the magnetic field components, while the generalized momenta are related to the electric field components or other relevant quantities. The Hamiltonian equations describe the conservative dynamics of the system, and the coupling terms in the equations are interpreted as representing the interactions between the magnetic and electric field components, analogous to the Lorenz force in electromagnetism. The model is implemented using Python, and the Hamiltonian equations are numerically solved using the odeint function from the scipy.integrate module. The resulting dynamics of the magnetic field components are visualized using matplotlib. While the model is highly simplified and does not capture the full complexity of neocortical dynamics, it serves as a starting point for investigating the potential role of magnetic dynamos and Lorenz force interactions in the brain. The paper discusses the limitations of the current model and highlights the need for further refinements, such as incorporating more realistic biological constraints, considering energy dissipation and compensation mechanisms, and validating the model against experimental data. Future work should focus on developing a more comprehensive and biologically plausible model that integrates the latest findings from neuroscience, physics, and computational modeling. By presenting this simplified Hamiltonian model, the paper aims to stimulate further research and discussion on the potential significance of magnetic dynamos and Lorenz force interactions in neocortical dynamics. The model provides a framework for exploring these hypothesized mechanisms and may guide future experimental and theoretical investigations in this emerging field of neuroscience

This work introduces a neuromorphic sensor based on force-sensing resistors (FSR) and spiking neurons for robotic systems. The proposed sensor integrates the FSR in the schematic of spiking neuron in order to make the sensor to generate spikes with frequency that depends on the applied force. The performance of the proposed sensor is evaluated for the control of a SMA-actuated ro-botic finger by monitoring the force during steady state when the finger pushes on a tweezers. For comparison purposes, we performed similar evaluation when the SNN receives input from a widely used compression load cell (CLC). The results show that the proposed FSR based neuro-morphic sensor has very good sensitivity to low forces and the function between the spiking rate and the applied force is continuous with good variation range. However, when compared to the CLC, the proposed sensor has lower linearity of the response, but it benefits from two orders of magnitude lower power consumption. These aspects imply that the neuromorphic sensor based on FSR are useful for bioinspired control of humanoid robotics representing a low power and low cost alternative the widely used sensors.

The problem of normal impact of a rigid sphere onto a Maxwell viscoelastic solid half-space is considered. The first-order asymptotic solution is constructed in the framework of Hunter’s model of viscoelastic impact [Hunter, S. C., 1957. Energy absorbed by elastic waves during impact. Journal of the Mechanics and Physics of Solids, 5(3), 162–171.]. In particular, simple analytical approximations have been derived for the maximum contact force and the time to achieve it. A linear regression method is suggested for evaluating the instantaneous elastic modulus and the mean relaxation time from a set of experimental data collected for different impactors and impact velocities.

The thesis proposes a argument that a mass point moving in a horizontal circle on the Earth's surface can generate a radial centrifugal force of the Earth's center of mass, thus realizing an unconventional anti-gravity path. And through the theoretical analysis of the difference in the distribution of gravitational acceleration at different latitudes caused by the rotation of the earth, and the centrifugal force of a mass point moving in a horizontal circle on the earth's surface is analyzed, the validity of the argument is demonstrated. At the same time, the paper puts forward two possible basic principles, and makes theoretical analysis and demonstration. Conceive of the concrete experimental verification of principle two is proposed. Four technical schemes for antigravity ascent are proposed and basic analysis is made. On the premise of not fully considering the practical technical ability, it is theoretically proved that three of them have realistic operability and development potential. In theory, this paper opens up a different way of anti-gravity for human beings, which will bring new ideas and prospects for human beings to get rid of the bondage of gravity.

The paper presents the prediction of hydrodynamic characteristics of different rudder -plane configurations behind a submarine in deep water through the Reynolds-Averaged Navier-Stokes method in Ansys Fluent Solver. The hydrodynamic force and moment acting on the Cross-plane, X-plane, and Y-plane rudder configurations are analyzed for estimating hydrodynamic coefficientsfor predicting the advantages of each configuration to control the ship. The obtained results show that X-force of the X-plane rudder configuration is larger than the force acting on the Cross-plane rudder and Y-plane rudder configurations. However, Y-force, and Z-force of the X-plane rudder configuration are significantly greater than the Y-force of the left configurations. The same tendency can be seen in the moment of the X-plane rudder about the y-axis and z-axis. The roll moment induced by the Y-plane and Cross-plane rudder configurations is significantly larger than the case of the X-plane rudder configuration.

This paper comprehensively reviews sensors and sensing devices developed or/and proposed so far utilizing two smart materials: electrorheological fluids (ERFs) and magnetorheological materials (MRMs) whose rheological characteristics such as stiffness and damping can be controlled by external stimuli, an electrical voltage for ERFs and a magnetic field for MRMs, respectively. In this review article, the MRMs are classified into magnetorheological fluid (MRF), magnetorheological elastomer (MRE) and magnetorheological plastomer (MRP). To easily understand the history of sensing research using the two smart materials, the order of this review article is organized in a chronological manner of ERF sensors, MRF sensors, MRE sensors and MRP sensors. Among many sensors fabricated from each smart material, one or two sensors or sensing devices are adopted to discuss on the sensing configuration, working principle and specifications such as accuracy and sensitivity. Some sensors adopted in this article include force sensor, tactile device, strain sensor, wearable bending sensor, magnetometer, display device and flux measurement sensor. After briefly describing what have been reviewed in a conclusion, several challenging future works, which should be done for practical applications as sensors or sensing devices, are remarked in terms of new technologies such as artificial intelligence neural network in which several parameters affecting the sensor signals can be precisely tuned or controlled. It is sure that this review article is very helpful to make creative sensors using not only the proposed smart materials but also several different types of smart materials including shape memory alloys and active polymers.

(i) Investigations of stellar systems known as wide binaries suggest that Newton’s law of gravitation breaks down at low accelerations. This can be explained by proposing a fifth force with $U(1)$ gauge symmetry, whose corresponding gauge boson is the sought for dark matter candidate. (ii) Relativistic causality (i.e. no faster than light signalling) permits nonlocal correlations stronger than those permitted by quantum mechanics. This can be explained if our universe possesses a second 4D spacetime with a signature opposite to ours. (iii) Such a fifth force, and a second spacetime, arise naturally in a recently proposed theory of unification based on an $E_8\times E_8$ symmetry. Our spacetime arises from breaking of an $SU(2)_R\times U(1)_{YDEM}$ symmetry, and the second spacetime arises from broken electroweak symmetry.

Tellurium exhibits exceptional intrinsic electronic properties. However, investigations into the modulation of tellurium's electronic properties through physical modification are notably scarce. Here, we present a comprehensive study focused on the evolution of the electronic properties of tellurium crystal flakes under plasma irradiation treatment by employing conductive atomic force microscopy and Raman spectroscopy. The plasma-treated tellurium experienced a process of defect generation through lattice broken. Prior to the degradation of electronic transport performance due to plasma irradiation treatment, a remarkable observation emerged: in the low-energy region of hydrogen plasma-treated tellurium, a notable enhancement in conductivity was unexpectedly detected. The mechanism underlying this enhancement in electronic transport performance was thoroughly elucidated by comparing it with the electronic structure induced by argon plasma irradiation. This study not only fundamentally uncovers the effects of plasma irradiation on tellurium crystal flakes, but also unearths an unprecedented trend of enhanced electronic transport performance at low irradiation energies when utilizing hydrogen plasma. This abnormal trend bears significant implications for guiding the prospective application of tellurium-based 2D materials in the realm of electronic devices.

Aiming at the development of the application of massive and heterogeneous LEO constellations, the influence of typical perturbation forces on the orbit prediction of LEO satellites at different altitudes is analyzed. Firstly, the main perturbation force model of LEO satellites is introduced. Then experiments for analyzing the influence of orbit prediction on LEO satellites at different altitudes are designed. Finally, the influence of typical perturbation forces on the orbit prediction under different prediction durations by numerical analysis is assessed systematically, and the orbit prediction of LEO satellites with different non-spherical gravitational field orders, ocean tide orders and atmospheric density models were compared and calculated. The research results show that different orders of non-spherical gravitational fields should be considered when the altitude of satellites is different, the reasonable gravitational field orders for LEO satellites at 500km, 1000km, 1500km and 2000km under 1-hour forecast time are 140x140, 80x80, 60x60 and 40x40 orders, the reasonable orders of ocean tide perturbation for 1500km and 2000km satellites are 20x20 orders. Under the 24-hour forecast time, atmospheric resistance has a great influence on the precision of LEO satellites at orbit altitude below 1,000km. The forecast deviation of the LEO satellites orbit at 500km reaches 8751.576m. The difference of orbit precision between different atmospheric density models is in the meter level. The orbit deviation by the Standard Atmosphere 1976 and NRLMSISE 2000 atmospheric models respectively reaches 25.494m. Relevant conclusions provide support for the optimization and selection of dynamical models in high precision orbit determination and fast orbit prediction of LEO satellites.

A novel technique suitable for propulsion of small unmanned aerial vehicles (UAV) is discussed in this paper. This approach utilizes the rotational energy of airborne gyro rotors and converts it into translational propulsion for the vehicle. The energy conversion is achieved by generating precisely directed centrifugal force pulses through short-duration rotor unbalances. The accurate control of the timing and magnitude of these unbalances is crucial for successful propulsion generation. Our first-order theory of controlled unbalance propulsion (CUP) predicts the potential for achieving high translational accelerations and vehicle velocities up to orbital levels. Power saving levitation of UAVs can be attained. In this paper, we provide traceable evidence that pulsed centrifugal propulsion is based on well-established laws of physics and can be realized using state-of-the-art technologies.

In mining machines with friction discs, but also in multi-rope traction elevators, it is necessary to distribute the applied tensile load, generated by the weight of the cage and counterweight, evenly in all cross-sections of the load-bearing ropes. Hydraulic devices used for this purpose can operate on the principle of Pascal's law. The article presents a structural design, a 3D model and an implemented solution of a laboratory device capable of simulating a practical method of evenly distributing the total weight of the load into partial tensile forces of the same size acting on a selected number of load-bearing ropes. The laboratory equipment uses two pairs of three steel cables of finite length for the simulations. During the experimental measurements, tensile forces derived from the tractive force of the piston rods, pushed into the bodies of the hydraulic cylinders by the pressure of the hydraulic oil supplied through the pipeline under the pistons of the hydraulic cylinders, were detected. The resulting amount of hydraulic oil pressure in the hydraulic circuit influenced by different values of the hydraulic oil pressures in the hydraulic cylinders and by the pressure in the supply pipe was experimentally studied on the laboratory equipment. Simulations were also carried out in order to detect the hydraulic oil pressure in the hydraulic circuit caused by the change in the different magnitudes of the tensile forces in the ropes From the experiments carried out, it follows that with the appropriate choice of hydraulic elements and the design of the hydraulic circuit, the weight of the load, acting as the total pulling force in the ropes, can be evenly distributed (with a deviation of up to 5%) to all cross-sections of the load-bearing ropes. If the exact values of the hydraulic oil volumes under the pistons of all hydraulic cylinders are not known, it is not possible to calculate the pressure values in the hydraulic circuit when the valves of the hydraulic pipes are gradually opened.

Efficient fixed crane position analysis is critical in precast buildings construction to maximize lifting efficiency for precast elements. The primary objective is to minimize the travel distances of fixed cranes, thereby enhancing operational efficiency and cost control. This involves strategically reducing the distances between the transport truck parking, where elements are stored, the fixed crane, and the construction installation point. Despite its significance, existing studies often overlook the dynamic movement efficiency of transport trucks, particularly when dealing with multiple transport trucks and various models of fixed cranes, rendering the opti-mization of this scenario a challenging NP-hard problem susceptible to combinatorial explosion. This study presents a novel mathematical model leveraging the Genetic Algorithm (GA). The model aims to solve optimal model and position of fixed cranes, along with identifying ideal positions for transport truck parking. The study's methodology is validated and demonstrated through a project case study. Comparative analyses between the proposed model and the original planning underscore a noteworthy 6% reduction in both duration and costs when lifting elements directly from transport trucks, as opposed to establishing an on-site stock yard. Furthermore, the developed GA exhibits a substantial improvement in final solutions, achieving a remarkable 30% reduction in both operational duration and costs. This research contributes valuable insights into fixed crane position analysis of precast building construction, providing foundation for enhanced operational efficiency and cost-effectiveness in the industry.

This study explores the significance of active suspension systems for vehicles with lower chassis compared to conventional ones, aiming at the development of future automobiles. Conventional linear MR (Magneto-Rheological) dampers were found inadequate in ensuring sufficient vibration control because the vehicle's chassis becomes lowered in the unmanned vehicles or purposed based vehicles. As an alternative, a rotary type of MR damper is proposed in this work. The proposed damper is designed based on pre-specified design parameters through mathematical modeling and magnetic field analyses. Subsequently, a prototype of the rotary MR damper identical to the design is fabricated, and effectiveness is shown through experimental investigations. In configuring the experiments, a proportional-integral (PI) controller is employed for current control to reduce the response time of the damper. The results presented in this work provides useful guidelines to develop a new type of MR damper applicable to various types of future vehicles’ suspension systems with low distance from the tire to the body floor.

: Considering that Einstein's relation between the diffusion coefficient and the drift mobility of the free randomly moving charge carriers in homogeneous materials including metals is always valid, it is shown that the effective electric force acting on free electrons in metal depends on the ratio between the kinetic free electron energy at the Fermi surface to the classical particle energy 3kT/2. The electrical resistivity of elemental metals dependence on very low temperatures has the quadratic term, which has been explained by electron-electron scattering. In this paper, it is shown that the quadratic term of the electrical resistivity at low temperatures is caused by scattering of the free RM electrons by electronic defects due to linear effective free electron scattering cross-section dependence on temperature, but not by electron-electron scattering.

The reconstruction of traffic accidents has grown as an interdisciplinary field since the first accident occurred. Various methods have been developed over time, starting with primary data collected at the scene of the accident. In this work, I proposed a method by which the value of the force in the safety belt buckle can be determined when it is equipped with a pretensioning system with pyrotechnic trigger in the tube, PBP or PLP type. The anti-return system of the pretensioner mechanism, which prevents the passenger's body from moving forward, contains a set of balls that block the movement of the piston in the pretensioner tube after its activation. When limiting the movement, the force the human body exerts on the safety belt webbing is transformed into the deformation of the pretensioner tube by the balls of the anti-return system. Depending on the magnitude of the force, the marks left by the balls differ. I propose a relationship of dependence between the acting force and the deformation of the tube. An experimental test bench was created to perform shock traction tests on the pre-tensioning system, under similar conditions to those of the human body acting on the belt in case of a frontal collision. Following the tests, the force value of the seat belt buckle cable and the diameter of the spherical indentations that the balls left in the pretensioner tube were measured. A mathematical model was proposed to determine the normal force with which a ball from the anti-return system deforms the tube. The normal force was also determined by two other methods specific to contact mechanics and used in the specialized literature. By comparing the normal forces obtained by the three methods, a good correlation between the proposed mathematical model and the Komvopoulos-Ye method resulted, the "Hardness" method not being suitable for this study. The determined polynomial regression curve allows finding out the force in the cable of the closer depending on the size of the deformations produced by the balls in the tube. The forces in the belt webbing can be thus determined and biomechanics specialists can evaluate the injuries to the chest and abdomen of the occupants of a vehicle.

Glycerol represents a useful functional component of heat-transfer fluids. Glycerol is known to be triboelectrically active. We report how the flow of glycerol, stopped in a cylindrical coiled pipe, influences horseradish peroxidase (HRP) enzyme. Namely, glycerol flow was pumped through the coil and then stopped. After that, we incubated the 0.1 µM solution of HRP near the side of the coil, and then adsorbed HRP onto mica. This operation markedly increased the HRP aggregation on mica in comparison with the control sample. We explain this phenomenon by the influence of triboelectrically induced electromagnetic fields. Our results can be useful in the development of flow-based systems for biosensors and bioreactors.

A key step in the study of tree pathology is the identification of appropriate method for inoculating pathogens of diseases in branch and trunk. Pathogens of diseases in branch and trunk are commonly inoculated through punching, burning, and toothpick inoculation. However, there is a lack of comparative analysis of the inoculation outcomes of these three methods. In this work, Six‐year‐old P. alba var. pyramidalis were inoculated with V. sordida, using punching, burning, and toothpick techniques, respectively, to investigate the differences in the effectiveness of these inoculation methods. Results reveal that the incidence rate was 93.55% in the toothpick inoculation group, significantly higher than 80.65% in the burning inoculation group (p = 0.007), while punching inoculation exhibited significant pathological responses in the early stages, with spontaneous healing in the later stage. Addi-tionally, toothpick inoculation was more efficient in inducing Valsa canker when inoculating the pathogen at the bottom of the tree, with lower intra‐ and inter‐row spacing (stand density) providing better outcomes than higher intra‐ and inter‐row spacing. The results of this study demonstrate that toothpick inoculation is an optimal option for studying the artificial inoculation of V. sordida in six‐year‐old P. alba var. pyramidalis, providing technical support for research on poplar diseases and offering a theoretical basis for the inoculation of other diseases in branch and trunk.

The forest regeneration phase in Sweden commonly involves mechanical soil preparation followed by planting of Scots pine or Norway spruce seedlings. The prepared soil offers planting positions with different properties, including decreased damage by pine weevil (Hylobius abietis L.). Nitrogen fertilization can be applied at the time of planting to aid establishment of the seedlings. In this study we compared the effect of organic nitrogen-fertilization for different planting positions, and seedling sizes on early survival and growth of Scots pine and Norway spruce seedlings. The main planting positions were capped mound, hinge, and mineral soil. Seedlings planted close to organic material were categorized as “low quality positions”, since proximity to organic material increase pine weevil attraction. Higher mortality rates related to pine weevil damage were recorded for seedlings planted in the low-quality positions, regardless of seedling size or N-fertilization. Pine weevil attack rates increased with increasing seedling size. Growth was in general lowest in mineral soil positions. The effect of organic N-fertilization on growth was positive for spruce regardless of planting positions and seedling size, while depending on planting position and seedling size for pine, indicating that effects of organic N-fertilization depend on seedling species, -size and planting position.

This paper revisits the analytical theory of fractional vibrations with the highlights in five aspects. First, we address the cases of structures with frequency dependent mass or damping or stiffness in Sections 2-4. Second, we introduce the theory based on the general second-order vibration motion equation with frequency dependent elements (mass, damping, stiffness) in Sections 5-7. Third, we present the analytical theory of seven specific classes of second-order vibration systems with frequency dependent mass or damping or stiffness in Sections 8 and 9. Fourth, we bring forward the analytical theory of seven classes of fractional vibration systems in Sections 10-12. Finally, as an application, we give the closed form expression of the forced response to multi-fractional Euler-Bernoulli beam in Section 13. The explanation of the nonlinearity of fractional vibrations is given in Section 14.

This paper presents laboratory devices on which experimental measurements were carried out to prove the validity of the assumption about the reduction of vibrations transmitted to the conveyor belt structure generated by the impact forces of falling material grains in the places of transfer or on the hoppers of conveyor belts. In order to limit damage to the conveyor belts caused by the impact of the sharp edges of material grains, conveyor belts are supported by impact rollers or impact rubber rods in the places of transfers and on the hoppers of belt conveyors. The flattened ends of the impact rollers are inserted into the grooves of steel brackets installed on the supports of the fixed conveyor idlers of a conventional design. In this paper, a special modification of the fixed conveyor idler is presented, which consists of inserting plastic brackets into the structurally modified roller axle holders of the fixed conveyor idler. Measurements were carried out on the first laboratory device, which showed that the specially modified fixed conveyor idler resulted in a higher damping of up to 15% of the impact forces of the falling weight on the rubberized hoop of the impact roller shell compared to the conventional fixed conveyor idler design. Measurements carried out on the second laboratory device show that the effective vibration velocity values detected at the points where the impact roller axis fits into the fixed roller table holder, i.e. points B and D, are higher than when using plastic brackets, up to 6% for a 108 mm diameter roller, compared to steel impact roller brackets.

The literature offers limited information on the effect of obesity on the rate of force development, a critical parameter for mobility in older adults. The objectives of this study were; to explore the influence of obesity on RFD in older adults and to examine the association between this neuromuscular parameter and walking speed. 42 older adults were classified into two groups: the control group (CG, n=22; age=81.13±4.02 years; Body mass index (BMI)=25.13±3.35 kg/m²), and the obese group (OG, n=20; age=77.71±2.95 years; BMI=34.46±3.25 kg/m²). Walking speed (m/s) was measured using the 10-meter walking test. Neuromuscular parameters of the plantar flexors were evaluated during a maximal voluntary contraction test using a dynamometer. The RFD was calculated from the linear slop of the force – time curve in two phases: from the onset of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200). The gait speed was lower in the OG compared to the CG (p

Electromagnetic actuation can support many fields of technology, such as robotics or biomedical applications. In this context, fully understanding the system behavior and proposing a low-cost package for feedback control is challenging. Modeling the electromagnetic force is particularly tricky because it is a nonlinear function of the actuated object’s position and coil’s current. Measuring in real time the position of the actuated object with the precision required for accurate motion control is also nontrivial. In this study, we propose a novel, cost-effective electromagnetic set-up to achieve position control via visual feedback. We actuate vertically and under different experimental conditions a 10 mm diameter steel ball hanging on a low-stiffness spring, demonstrating good tracking performance (the position error remains within ±0.5 mm with a negligible phase delay in the best scenarios). The experimental results confirm the feasibility of the proposed set-up, which is characterized by minimum complexity and realized with off-the-shelf and cost-effective components. For these reasons, such a contribution helps to understand and apply electromagnetic actuation even further.

Abstract: Understanding the reliability and sensitivity of jump testing is essential to determine the neuromuscular progress of athletes and make informed decisions. This study aimed to assess the reliability and sensitivity of countermovement jump (CMJ) and drop jump (DJ) tests metrics in female volleyball players. Sixteen semi-professional female volleyball players participated in the study. Intrasession and intersession reliability of CMJ and DJ metrics were evaluated using a randomized cross-over design. Dual force platform was used to collect data, and several dependent variables were calculated using forward dynamics. Intraclass correlation coefficients (ICC), coefficients of variation (CV) and minimum difference (MD) were calculated. The third attempt presented the highest values for both test, and changes in jump strategy in DJ. CMJ is consistent across sessions, while DJ also shows intersession differences (p<0.05) in 11 out of 15 variables. Most CMJ variables exhibit excellent reliability while DJ variables have lower reliability and higher variability. Concentric and eccentric impulses for DJ showed excellent reliability. Most CMJ variables showed excellent reliability and variability, DJ had lower reliability, higher variability, and lower sensitivity. These findings provide valuable information when assessing athletes' performance and highlight the reliability, sensitivity, and variability in jump performance for CMJ and DJ tests.

The refractive index of seawater is one of the essential parameters in ocean observation, so it is necessary to achieve high precision seawater refractive index measurement. In this paper, we propose a method for measuring the refractive index of seawater based on a Position Sensitive Detector (PSD). Theoretical model is established to depict the correlation between laser spot displacement and refractive index change, utilizing a combination of position sensitive detector and laser beam deflection principle. Based on this optical measurement method, a seawater refractive index measurement system was established. To effectively enhance the sensitivity of refractive index detection, a focusing lens was incorporated into the optical path of the measuring system, and simulations were conducted to investigate the impact of focal length on refractive index sensitivity. The calibration experiment of the measuring system was performed based on the relationship between refractive index of seawater and underwater pressure (depth). By measuring laser spot displacement at different depths, changes in displacement with respect to both refractive index and depth were determined. Experimental results demonstrate that the system exhibits a sensitivity of 9.9277×10−9RIU (refractive index unit), the refractive index deviation due to stability is calculated as ±7.545×10−9RIU. Thereby the feasibility of highly sensitive measurement of seawater refractive index is verified.

The ageing global population and changing labor force participation are having a profound impact on state pension programs worldwide, including Malaysia. However, the effects of an ageing workforce and declining fertility rates are having a significant impact on future trends in labor force participation and the duration of retirement. This paper presents an innovative examination of labor force participation rate (LFPR) forecasting within the context of an aging workforce, utilizing the Lee-Carter and Cairns-Blake Dowd stochastic models, traditionally applied to mortality data. By adapting these models to LFPR data, the study offers a novel perspective on predicting workforce participation trends and understanding the dynamics of retirement planning from year 2001 to 2047. Additionally, by incorporating the mortality forecasts from the United Nations, the research navigates through the complexities of applying actuarial methods to labor economics, revealing differentiated pathways for male and female participation in the labor market and the anticipated length of retirement. This study offers a unique comparison between the Lee-Carter and the Cairns-Blake-Dowd (CBD) LFPR models. It focuses on fitting and forecasting the LFPR of senior employees aged 50 to 64. The results highlighted discrepancies among models that demonstrated evidence of model risk for extended retirement duration.

Objective: Local ablation therapies (radiofrequency ablation (RFA), and microwave ablation (MWA)) are important as curative treatment option in patient with early-stage hepatocellular carcinoma (HCC) and option for intrahepatic tumor volume reduction in those with unresectable HCC. Various techniques; contrast-enhanced ultrasound (CEUS), real-time virtual sonography (RVS), artificial pleural and ascites fluid infusion, and body position change (BPC) have been used to accurately and safely perform local ablation therapies. However, there have been few reports on the usefulness of BPC. Therefore, this study focused on the usefulness of BPC during local ablation therapies in patients with HCC. Methods: We evaluated the technical success rates, treatment time, and prognosis of 283 nodules treated with local ablation therapies. Furthermore, we defined nodules adjacent to large vessels or extrahepatic organs, or poorly visible nodules using US as HCC in high-risk locations. High-risk locations HCC were classified into phase 1 (before active use of BPC, January 2018 to December 2019) and phase 2 (after active use of BPC, January 2020 to January 2022). Results: One hundred seventy-six nodules (62%) were classified as high-risk location group. Compared to non-high risk HCC, treatment-assist techniques, such as BPC (61 vs. 24 %, p<0.001), artificial pleural fluid infusion (24 vs. 5.6%, p<0.001), artificial ascites infusion (50 vs. 11%, p<0.001), fusion imaging (28 vs. 8.4%, p<0.001) and CEUS (26 vs. 4.7%, p<0.001) were performed more frequently for high-risk HCC. The technical success rates were 96% (271/283 nodules), 96% (167/173 nodules) and 95% (102/107 nodules), for all nodules, the high-risk location group and the non-high risk location group, respectively. In the high-risk location group, the technical success rates of the group without BPC were lower than that with BPC (91 vs. 99%, p=0.015). Only BPC was a related factor for the technical success rate for high-risk locations HCC (OR 10 (1.2-86), p=0.034). In contrast, no differences were found in the treatment time, the local tumor progression rates, intrahepatic distant recurrence rates, and overall survival between the group with BPC and that without BPC in the high-risk location HCC. Conclusion: BPC during local ablation therapies in patients with HCC in high-risk locations was safe and efficient. Body position should be adjusted for HCC in high-risk locations to maintain good US visibility and ensure safe puncture route in patients undergoing local ablation therapies.

Forensic anthropologists play a key role in skeletal trauma analysis and commonly use macroscopic features to distinguish between trauma types. However, this approach can be challenging, particularly in cases of highly comminuted or incompletely recovered fractures. Histological analysis of microscopic fracture characteristics in fractured bones may thus help provide additional information on trauma type and bone fracture biomechanics in general. This study analysed the extent of microcrack damage to osteons in long bones with blunt force trauma (BFT) and gunshot trauma (GST), from both traumatic death cases and post-mortem experimental fractures. We identified four types of osteonal damage (OD). In traumatic death cases, OD affecting the inside of the osteon and compromising the Haversian canal (type 1) was found to be indicative of BFT. Moreover, OD affecting the cement line (type 3) and interstitial lamellae (type 4) was more common in the GST samples. OD affecting the inside of the osteon without compromising the Haversian canal (type 2) was not found to be indicative of either trauma type. In cases of experimental fractures, our study revealed that post-mortem fractures in dry bone samples featured the highest amount of OD, particularly of type 4. This study also found that the experimentally produced GST featured similar OD pattern to GST death cases. These findings support our hypothesis that there are distinct osteonal damage patterns in human long bones with BFT and GST, which are of relevant value for trauma analysis in forensic anthropology.

Performance of the overhead squat may affect golf swing mechanics associated with golf-related low back pain. This study investigates the difference in lumbar kinematics and joint loads during the golf downswing between golfers with different overhead squat abilities. Based on the per-formance of the overhead squat test, 21 golfers aged 18 to 30 years were divided into the highest-scoring group (HS, N=10, 1.61 ± 0.05 cm, and 68.06 ± 13.67 kg) and lowest-scoring group (LS, N=11, 1.68 ± 0.10 cm, and 75.00 ± 14.37 kg). Data collection used a motion analysis system, two force plates, and TrackMan. OpenSim software was used to simulate the joint loads for each lum-bar joint. An independent t-test was used for statistical analysis. Compared to golfers demonstrat-ing limitations in the overhead squat test, golfers with better performance in the overhead squat test demonstrated significantly greater angular extension displacement on the sagittal plane, smaller lumbar extension angular velocity, and smaller L4-S1 joint shear force. Consequently, the overhead squat test is found to be a useful index to reflect lumbar kinematics and joint loading patterns during the downswing, and provides a good training guide reference for reducing the risk of a golf-related low back injury

(1) Background: This text emphasizes concerns regarding the safety of Spanish police officers at-tributed to inadequate training, employing biomechanics for the analysis and mitigation of risks during Use of Force training. The elevated global prevalence of musculoskeletal disorders under-scores the imperative for effective occupational health measures. The study concentrates on evalu-ating injury risks in novice police officers during Use of Force training. (2) Research method: The movements of police officers were captured using a Rokoko Smartsuit Pro equipped with 19 sen-sors. The Biomechanics of Bodies software processed the data, providing REBA and Marras risk scores. Statistical tests were conducted, and Operational Tactical Procedures (OTP) were inte-grated into police training. A diverse group of officers participated, categorized by training level and equipped with the Rokoko Smartsuit. (3) Results: The study evaluates police force training us-ing REBA and Marras methods. REBA scores indicate a moderate to high injury risk, suggesting effective technique design. ANOVA reveals no significant differences between training levels. Marras analysis, characterized by non-normal distribution, unveils varied risk perceptions among groups via the Kruskal-Wallis test. (4) Conclusions: The analysis of both the REBA and Marras methods implies the effectiveness of the OTP technique in reducing injury risks across dif-ferent training levels. The ANOVA test indicates no significant differences in REBA Maximum Scores between the groups. However, the Kruskal-Wallis test for Marras Probability of high-risk values suggests distinctions in medians between training levels. The combined analysis visually illustrates variations in membership regions between expert, intermediate, and novice groups.

To mitigate the interference of waves on offshore operation vessels, heave compensation systems find widespread application. The performance of heave compensation systems significantly influences the efficiency and safety of maritime operations. This paper establishes a mathematical model for winch-based active heave compensation system. It introduces a three-loop active disturbance rejection control (ADRC) strategy encompassing piston position control, winch speed control, and load displacement control, enabling real-time estimation and compensation of system disturbances, thereby enhancing the performance of the heave compensation system. To assess the effectiveness of this control strategy, the study employs Matlab/Simulink and AME Sim to construct a co-simulation model and conducts a comparative analysis with traditional PID control systems. The research findings indicate that the three-loop ADRC position control strategy consistently delivers superior compensation performance across various operational scenarios.

Experimental tests and numerical analyses were carried out on short, thin-walled channel columns with modified cross-sectional shape. The columns were loaded with an axial compressive force applied at the center of gravity of the cross section. Tests were carried out on a universal testing machine, while numerical analyses were performed in ANSYS software. The purpose of the tests was to determine the values of critical forces for the compressed columns and to determine the values of maximum forces at which failure of the columns occurs. Critical forces were determined based on the strain-averaged method. Based on the study, it was found that the strength and resistance to loss of stability of columns is primarily affected by their stiffness, and therefore by the shape of the cross-sections. In addition, for short columns, it seems more important to determine the value of maximum forces than the values of critical forces.

Background. The markerless motion capture system (MLS) is a new technology that uses deep learning to detect body segments from digital images. This study tested the agreement between the MLS and a force-plate based system (FPS, “gold standard”) to quantify stability control and motor performance (MP) during gait initiation (GI). Methods. Healthy adults (young and elderly) and patients with Parkinson’s disease (PD) performed GI series at spontaneous and maximal velocity on an FPS while being filmed by an MLS. Signals from both systems were used to compute the peak of forward center-of-mass velocity (indicator of MP) and the braking index (BI, indicator of stability control). Results. Descriptive statistics indicated that both systems detected between-groups differences and velocity effects similarly, while a Bland-Altman (BA) plot anal-ysis showed that BI and MP mean biases were virtually zero in all groups and conditions. Bayes factor 01 indicated strong (for BI) and moderate (for MP) evidence that both systems provided equivalent values. However, trial-by-trial analysis of BA plots revealed the possibility of differ-ences > 10% between the two systems. Conclusion. Although non-negligible differences do occur, MLS appears to be as efficient as FPS in detecting PD and velocity condition effects on BI and MP

This article describes the study and digital implementation of a system onboard a TMS 3208F28335 ® DSP for vector control of the bearing motor speed with 4 poles split winding with 250W of power. Smart techniques: ANFIS and Neural Networks were investigated and computationally implemented to evaluate the bearing motor performance under the following conditions: operating as an estimator of uncertain parameters and as a speed controller. Therefore, the MATLAB program and its toolbox were used for the simulations and the parameter adjustments involving the structure ANFIS (Adaptive-Network-Based Fuzzy Inference System) and simulations with the Neural Network. The simulated results showed a good performance for the two techniques applied differently: the estimator and a speed controller using both a model of the induction motor operating as a bearing motor. The experimental part for velocity vector control uses three control loops: current, radial position, and speed, where the configurations of the peripherals, that is, the interfaces or drivers for driving the bearing motor.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

The automotive industry has witnessed a significant push towards increased fuel efficiency and reduced carbon emissions. Among many factors influencing overall vehicle efficiency, aerodynamic drag is a critical consideration, accounting for a substantial portion of fuel consumption. Our investigation focused on the drag coefficients of three prominent 2023 passenger car models – the Toyota Corolla, Hyundai Elantra, and Kia Soul. Using ANSYS Fluent to perform computational fluid dynamics, we demonstrated an inverse correlation between drag force and gas mileage, underlining the significance of aerodynamic design in fuel efficiency. Notably, the Hyundai Elantra emerged as the most aerodynamically efficient of the three vehicles, followed closely by the Toyota Corolla. In contrast, the boxier-designed Kia Soul exhibited significantly higher drag coefficients and drag forces, rendering it the least efficient of the trio. These findings emphasize the importance of environmental factors in car design. Shaping aerodynamic profiles directly impacts fuel efficiency, stability, and overall performance.

A stable match, an intercuspated maxilla-mandible relation is the universally accepted goal for dental restorative interventions, yet the underlying sensorimotor mechanisms to achieve this goal in the natural jaw closure remains to be elucidated. Dentists have intuitively regarded peripheral sensory innervation from tooth contacts as a significant control element for jaw muscle actions, both in the state of health and in cases of pathological dysfunction. However, therapeutical interventions for reshaping the dental arch anatomy and jaw relations have not always been successful. Repetitive masticatory chewing cycles, swallowing, talking, as well as volitional jaw-opening and -closing involve stereotyped neural commands from the central nervous system that are modulated in reaction to the sensory afferent feedback from the peripheral neurons and their sensor organs. The aim of this article is to describe, on a fraction of a second time-scale, the minuscule tilts and kinematic events of mandible during the making of a stable match with maxilla. Evidence of the importance of tooth contacts as the sensorimotor motivation of each of the successive kinematic steps of the “mandible-meets-maxilla-narrative” are discussed.

Star copolymer films were studied for confirming the role of film morphology in antimicrobial activity previously reported. With this scope, films of a two-branches copolymer, namely m-PEG-(MMA-ran-DMAEMA)2, containing ≈ 40 % in mol of non-quaternized 2-(dimethylamino)ethyl methacrylate, were produced by using spin-coating, drop-casting and casting deposition techniques, thus obtaining ultra-thin, thin and thick films, respectively. The morphology is generally flat for thin and thick films, but it becomes substrate dependent for ultra-thin films where the film planarization effect is not efficient. Mechanical properties of such films were investigated by Force Volume Maps in both air and liquid. In air, ultra-thin films are in the substrate-dominated zone and thus the elastic modulus E is overestimated, while E reaches its bulk value for thin and thick films. In liquid (water), E follows an exponential decay for all films with a minimum soaked time t0 of 0.37 and 2.65 h for ultra-thin and thin and thick films, respectively. After this time, E saturates to a value in average 92 % smaller than that measured in air due to films swelling. Such results confirm the role of morphology envisaged in literature, suggesting also an additional role of mechanical properties in the antimicrobial activity.

Atomic force microscopes are used, beside their principal function as surface imaging tools, in surface manipulation and measurement of interfacial properties. In particular, they can be modified to measure lateral friction forces that occur during the sliding of the tip against the underlying substrate. However, the shape, size, and deformation of the tips profoundly affect the measurements in a manner that is difficult to predict. In this work, we investigate the contribution of these effect to the magnitude of the lateral forces during sliding. The surface substrate is chosen to be few-layer AB-stacked graphene surface whereas the tip is initially constructed from face-centered cubic gold. In order to separate the effect of deformation from shape, rigid tips of three different shapes were considered first, namely a cone, a pyramid and a hemisphere. The shape was seen to dictate all aspects of the interface during sliding, from temperature dependence to stick-slip behavior. Deformation was investigated next by comparing a rigid hemispherical tip to one of identical shape and size but with all but the top three layers of atoms free to move. The deformation, as also verified by an indentation analysis, occurs by means of the lower layers collapsing on the upper ones, thereby increasing the contact area. This collapse mitigates the friction force and decreases it with respect to the rigid tip for the same vertical distance. Finally, the size effect is studied by means of calculating the friction forces for a much larger hemispherical tip whose atoms are free to move. In this case, the deformation is found to be much smaller but the stick-slip behavior is much more clearly seen.

We present a design of electrostatic comb driver to improve and investigate its actuation performance. The proposed electrostatic comb actuator (ECA) is composed of two set of interdigitated comb microstructures, the inner combs are fixed to form the fish-bone microstructures and the outer combs are movable and connected to crab-leg flexure beams microstructures. The ECA is investigated to optimize the actuation performance by changing the comb shape and the intersection angle of crab-leg flexure beams. The comb shapes are compared between the traditional rectangle shape and the trapezoid shape, while the intersection angles of crab-leg flexure beams are compared between 45°, 60°, and 90° on the influences of ECA displacement and stability characteristics. These parameters are investigated for their impacts on the dynamic comb displacement and driving voltage. Under the condition of a driving DC bias voltage of 100 volts, the ECA displacement is firstly increased and then gradually decreased by increasing the comb finger length. The maximum displacement of ECA with trapezoid comb is 47.2 μm while that of ECA with rectangle comb is 22.4 μm. By using trapezoid comb shape to replace the rectangle comb under the same conditions, the ECA displacement is improved 2-fold. To enhance the stability of ECA system, the intersection angle of 90˚ of crab-leg flexure beams shows highest stability that is great better than the intersection angle of 45° and 60° of crab-leg flexure beams by increasing the driving different DC bias voltage to 100 volts on ECA. The stability of the ECA with the intersection angle of 90° of crab-leg flexure beams is enhanced 1.1-fold and 1.4-fold compared to that of 45° and 60° of crab-leg flexure beams, respectively. This design provides an optimized approach to the electrostatic comb actuator that can be used expansively in the gyroscope, motion sensor, position sensor, imaging sensor, optical sensor, and so on.

Contact inhibition (CI) represents a crucial tumor-suppressive mechanism responsible for controlling the unbridled growth of cells, thus preventing the formation of cancerous tissues. CI can be further categorized into two distinct yet interrelated components: CI of locomotion (CIL) and CI of proliferation (CIP). These two components of CI have historically been viewed as separate processes, but emerging research indicates that they share both distinctive and common pathways. Moreover, they exhibit intriguing intersections with mechanotransduction, a process that involves cells sensing and responding to mechanical forces. This review article describes the intricate interplay between mechanical forces and CI, shedding light on how these forces regulate CIL and CIP. Emphasis is placed on filamin A (FLNA)-mediated mechanotransduction, elucidating how FLNA senses mechanical forces and translates them into crucial biochemical signals that regulate cell locomotion and proliferation. In addition to FLNA, trans-acting factors (TAFs) emerge as sensitive players in both CI and the mechanotransduction process. This article presents methods for identifying these TAFs and profiling the associated changes in chromatin structure, offering valuable insights into CI and mechanotransduction regulation. Finally, it addresses unanswered research questions in these fields and delineates their possible future directions.

The cyclic universe theory is a model of cosmic evolution according to which the universe undergoes endless cycles of expansion and cooling, each beginning with a big bang and ending in a big crunch. In this paper, the researcher finds a unique property of Space-time, this particular and marvelous nature of space shows us that space can shrink, expand, and stretch. This property of space is caused the size of the Universe changing over time: growing or shrinking. The observed accelerated expansion, which relates the stretching of Shrunk space for the new theory, is derived. This model is based on three underlying notions: First, the Big Bang was not the beginning of Space-time, but rather at the very beginning fraction of a second there was an infinite force of infinite Shrunk space in the cosmic singularity, that force gave rise to the big bang and caused the rapidly growing of space-time, and all other forms of energy are transformed into matter and radiation and a new period of expansion and cooling begins. Second, there was a previous phase leading up to it, with multiple cycles of contraction and expansion that repeat indefinitely. Third, the two principal long-range forces are the gravitational force and the repulsive force generated by shrunk space. They are the two most fundamental quantities in the universe that govern cosmic evolution. They may provide the clockwork mechanism that operates our eternal cyclic universe. The space will not continue to expand forever, no need however, for dark energy and dark matter. This model of Space-time and its unique properties enables us to describe a sequence of events from the Big Bang to the Big Crunch.

This paper focuses on improving the tracking accuracy for servo systems and increasing the contouring performance of precision machining. The dynamic friction during precision machining is analyzed using the LuGre model. The dynamic and static parameters in the friction model are efficiently and accurately identified using the improved Drosophila Swarm Algorithm based on cross-mutation. The friction tracking error can be deduced by the friction state space and an expression is derived. To compensate for the tracking error caused by friction, a feedforward compensation control is designed to avoid signal lag in traditional friction controllers. Furthermore, the factors of multi-axis parameter mismatching that impact the machining profile accuracy are analyzed for multi-axis control. An adaptive cross-coupled control-based pre-compensation strategy of contour error is designed to reduce both the tracking error and the contour error. The effectiveness of the proposed method is validated through several experiments, which demonstrate a remarkable improvement in tracking performance and contour accuracy.

Reliable motor control design is a critical part of the electric vehicle application. Control techniques and motor control devices play an important role in achieving system reliability. In this study, motor control devices have been proposed to implement control techniques in sensorless PMSM. Motor control devices including PWM signal generation by FPGA, gate driver circuit (GDC), and power inverter were developed to be integrated into single-stage motor control devices for sensorless motor control applications. Improvements in GDC design have been the focus to increase the performance of the motor control devices used. Switching losses due to the parasitic elements caused ringing switching behavior of the power inverter circuit, which reduces the performance when the system is integrated. Moreover, in the implementation of sensorless motor control using observer techniques, these conditions affect the accuracy of rotor position estimation, which uses the current or voltage information of the power converter as a variable in the observer design model. Therefore, a GDC design using IR2110 with additional ringing suppression circuit configuration was proposed for the application of motor device control topology to improve the performance of sensorless motor control system. Furthermore, the reduction of switching losses, reduction of current distortion, and accuracy of rotor position information were confirmed by experimental results.

In order to reveal the frost heaving mechanism of void water behind the lining of high-speed railway tunnels in cold regions，the voids were first classified according to the positional relationship between voids and waterproof panels，and then the water supply and discharge conditions of different types of voids were investigated，then the influence of the excretion conditions on the frost heave force was experimentally studied. Based on these conditions，circular wedge-shaped and flying saucer-shaped void freezing models were established to analyze the evolution process of accumulated water frost heave. Then，according to the relative position of the excretion channel and the void，the excretion coefficient was introduced，and the calculation method of the frost heaving force of the voided water was proposed，and the influencing factors and laws of the frost-heave force were revealed. The results are shown as follows: 1) The blockage of the excretion channel will lead to the generation of frost heaving force; 2) The freezing and thawing process of the water within the cavity develops from the thinnest part of the void edge to the thicker part，and the process of frost heave-thaw，water replenishment-re-freeze heave of the water within the cavity leads to greater and greater frost heave force; 3) The frost-heaving force of the water within cavity is controlled by the void height and the position of the excretion channel. The larger the cavity height is or the closer the excretion channel is to the bottom surface of the void，the greater the frost-heave force is.

Real-time multi-axis distributed tactile sensing is a critical capability if robots are to perform stable gripping and dexterous manipulation, as it provides crucial information about the sensor-object interface. In this paper, we present an optical-based 6-axis tactile sensor designed in a fingertip shape for robotic dexterous manipulation. The distributed sensor can precisely estimate local XYZ force and displacement at ten distinct locations, and provide global XYZ force and torque measurements. Its compact size, comparable to that of a human thumb, and minimal thickness allow seamless integration onto existing robotic fingers, eliminating the need for complex modifications to the gripper. The proposed sensor design uses a simple, low-cost fabrication method. Moreover, the optical transduction approach uses light angle and intensity sensing to infer force and displacement from deformations of individual sensing units that form the overall sensor, providing distributed 6-axis sensing. The local force precision at each sensing unit in the X, Y, and Z axes is 20.89 mN, 19.19 mN, and 43.22 mN, respectively, over an local force range of approximately ±1.5 N in X and Y and 0 to -2 N in Z. The local displacement precision in the X, Y and Z axes is 56.70 μm, 50.18 μm and 13.83 μm, respectively, over a local displacement range of ±2 mm in the XY directions and 0 to -1.5mm in Z (i.e., compression). Additionally, the sensor can measure global torques, Tx, Ty and Tz, with a precision of of 1.90 N-mm, 1.54 N-mm and 1.26 N-mm, respectively. The fabricated design is showcased by integrating it with an OnRobot RG2 gripper and illustrating real-time measurements during in simple demonstration task which generate changing global forces and torques.

This study explores the application of numerical analysis and material models to predict ice impact loads on ships and offshore structures operating in polar regions. An explicit finite element analysis (FEA) approach was employed to simulate an ice and steel plate collision experiment conducted in a cold chamber. The pressure and strain history during the ice collision were calculated and compared with the experimental results. Various material model configurations were applied to the FEA to account for the versatile behavior of ice—whether ductile or brittle—its elastic-plastic yield criteria, and its dynamic strain rate dependency. In addition to the standard linear elastic perfectly plastic and linear elastic-plastic relationships, this study incorporated the crushable foam and Drucker-Prager models, based on the specific ice yield criteria. Considering the ice’s strain rate dependency, collision simulations were conducted for each yield criteria model to compute the strain and reaction force of the plate specimens. By comparing the predicted pressures for each material model combination with the pressures from ice collision experiments, our study proposes material models that consider the yielding, damage, and behavioral characteristics of ice. Lastly, our study proposes a combination of ice material properties that can accurately predict collision force.

Landward displacement of coastal boulders is a morphodynamic signature of inundation and erosion processes. The study of these movements can provide useful elements for coastal hazards assessment. In this note, using open-access remote sensing resources, the 2017 to 2021 annual mobility of medium, coarse, and very coarse boulders spread over about 100 km of the eastern coast of the Gulf of Taranto (Italy) is detected. A large interannual variability was found. As established by multi-temporal object-based image analysis, one hundred and ten boulders changed position between July 2019 and June 2020, no boulder was displaced between July 2017 and July 2018, and few boulders were displaced between July 2018 and July 2019, and June 2020 and September 2021. A hydrodynamic analysis of the investigated boulder displacement led to the estimation of the energy of nearshore waves that hit the coast. The storm Detlef, that crossed over the Mediterranean Sea during 11-13 November 2019, is presumed to be the main cause of the massive displacement phenomenon.

Porous structures and micropatterning surfaces play a crucial role in the development of highly sensitive force sensors. However, achieving these two conductive architectures typically requires complex materials synthesis and expensive manufacturing processes. In this study, we introduce a novel conductive composite film featuring a porous/micropyramid hybrid conductive architecture, which is achieved through a straightforward process of materials mixing and one-step screen printing. By utilizing a deep eutectic solvent in the ink component, micropores are induced in the printed composite, while the mesh of the screen mask acts as a template, resulting in a micropyramid film surface. We have successfully realized highly sensitive flexible force sensors with multifunctional capabilities for perceiving normal force and shear force.

Tight junctions (TJ) are cell-cell adhesive structures that define the permeability of barrier-forming epithelia and endothelia. In contrast to this seemingly static function, TJs display a surprisingly high molecular complexity and an unexpected dynamic regulation, which allows the TJs to maintain a barrier in the presence of physiological forces and in response to perturbations. Cell-cell adhesion receptors play key roles during the dynamic regulation of TJs. They connect individual cells within cellular sheets and link sites of cell-cell contacts to the underlying actin cytoskeleton. Recent findings support roles of adhesion receptors in transmitting mechanical forces and promoting phase separation. In this review, we discuss newly discovered functions of cell adhesion receptors localized at the TJs and their role in the regulation of the barrier function.

Polyvinyl Alcohol (PVA)/ Graphene Quantum Dots (GQDs) polymer nanocomposite films have been prepared, and the relationship between their structural, thermal and nanoscale morphologi-cal properties, and their photoluminescent response, has been investigated. Although according to X-ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FT-IR) and Differential Thermal Analysis (DTA) the incorporation of GQDs does not significantly affect the percentage crystallinity of the PVA matrix, for a range of added GQD concentrations, Atomic Force Micros-copy (AFM) showed the formation of islands with apparent crystalline morphology on the surface of the PVA/GQD films, with GQD presumably acting as a nucleating agent for island growth. The incorporation of GQD also led to the formation of characteristic surface pores with increased stiffness and frictional contrast, according to Ultrasonic Force Microscopy (UFM) and Frictional Force Microscopy (FFM) data. The photoluminescence (PL) spectra of the films were found to de-pend both on the amount of GQD incorporated and on the film morphology. For GQD loads > 1,2wt%, a GQD-related band was observed at ~ 1650 cm-1 in FT-IR, along with an increase in the PL band at lower energy. For a load of ~2wt% GQD, the surface morphology was characterized by extended cluster aggregates with lower stiffness and friction than the surrounding matrix, and the PL signal decreased.

Background: The rate of force development (RFD) plays a pivotal role not only in preventing falls but also in ensuring successful completion of many functional tasks that demand swift muscle power rather than prolonged strength. Despite its importance, there is limited compre-hensive research on the relationship between RFD and walking speed, especially in older adults with Sarcopenic Obesity (SO). Objective: to investigate the influence of obesity on neuromuscular markers in older adults with SO and to assess the relationship between neuromuscular markers and gait speed in older adults with SO. Methods: a cohort of 42 participants was categorized based on their BMI into two groups: the sarcopenic non-obese group (CG, n=22; age=81.13±4.02; BMI=25.13±3.35) and the sarcopenic obese group (SOG, n=20; age=77.71±2.95; BMI=34.46±3.25). Gait speed was measured using a 10-meter test. Additionally, the isometric strength of the plantar flexor muscles was assessed during maximal voluntary contractions. Absolute Peak force (aPeak, N) were documented at intervals of 50 ms (a50, N), 100 ms (a100, N), and 200 ms (a200, N), subsequently normalized to body mass (r50, r100, r200, N). The RFD was derived in two phases: from the start of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200) and calculated from the linear slop of the force – time curve (Δ force/Δ time). Conclusion: Obesity negatively impacts neuromuscular markers in older adults. Notably, RFD emerges as the dominant factor influencing gait speed, accounting for an impressive 51% of its variability, far surpassing the impact of relative peak force. This underscores the imperative of evaluating neuromuscular health in older adults with SO to provide insights into mobility out-comes.

The observation of persons in the acute phase of ischemic stroke (IS) allowed to select a group of patients whose spontaneous motor activity stood out from the typical clinical picture of the hemiplegia syndrome. It has been noticed that these persons have presented tendency to shift the body weigh toward more affected side and the tendency to move the upper and / or the lower limb (not covered by the neurological syndrome) in simple, repetitive patterns. The purposes of this study were: to define noted kind of behavior, and to select symptoms which can predict the occurrence it. Persons (n=222) hospitalized due to first-time IS were as-signed to 3 groups. A: 78 persons with no lateralization of the neurological syndrome (LoNS). B: 109 persons with LoNS, O+: 35 persons, who at the beginning of hospitalization presented, apart from LoNS, charac-teristic motor symptoms. Persons underwent therapy depending on the neurological symptoms. If the pa-tient demonstrated the potential symptoms for overactivity of the less affected side (OLAS), to confirm it, trial therapy was performed. The predictive symptoms, selected among these from the index day, for the occurrence OLAS in sitting were distinguished: asymmetry in supine and simple, repetitive movements of nonparetic upper extremity.

Proprioceptive deficits accompanied with motor paresis after stroke, namely sensory ataxic motor paresis has a poorer prognosis of recovery than pure motor deficit. We aimed to investigate the effects of repetitive peripheral magnetic stimulation (rPMS) on sensory ataxic upper extremity (UE) paresis at acute stroke. Eighteen stroke participants with sensory ataxic UE paresis were randomized. rPMS group received five sessions of intervention per week, where 20 minutes of rPMS prior to 20 minutes of physical therapy (PT) every other day, alternating with 40 minutes of PT. The control group received five sessions of 40 minutes of PT/week. Outcome measures were Wolf motor function test (WMFT), UE motor section of Fugl-Meyer Motor Assessment Scale (FMA-UE), and Thumb localizing test (TLT). All assessments were compared before and after intervention. rPMS group received mean 6.5 sessions and the control group received 12.8 sessions, showing significantly imbalanced intervention due to different timing of hospital discharge. The imbalance was corrected by calculating gains of motor scores divided by sessions as Progress Rate (PR). Corrected gains (PR) of rPMS group was more significantly enhanced in WMFT and FMA-UE than control groups. rPMS group tended to improve TLT more than control one. rPMS might improve sensory ataxic UE paresis after stroke and proprioceptive deficit.

ABSTRACT(1) Background:. Because of the numerous debates about the training on the use of force provided to police officers, this study intends to evaluate several parameters (Police Ergonomic Parameters, PEP) in connection with such training. (2) Research method: : A smartsuit equipped with a set of 19 wireless sensors including triaxial accelerometers, Inertial Measurement Units (IMU), gyroscopes and geomagnetic sensors has been used. Biomechanics of Body (BoB) software application allowed to evaluate the risks associated to the basic technique number 1 of the Operational Tactical Procedures (OTP) with regard to the established parameters (PEP). The OTP basic technique number 1 was performed by 4 novice police officers. (3) Results: According to the evaluation of a number of specific parameters such as Rapid Entire Body Assessment (REBA), asymmetry over the sagittal plane, compression force at the L5-pelvic junction, shear force at the L5-pelvic junction and total muscle power, it was observed that the measured values clearly varied depending on each individual's performance, although they remained consistent with the values established by Police Ergonomic Parameters, and were significantly different from the values measured when a police officer used a traditional physical intervention procedure, in which case, the values measured were indicative of higher risks. (4) Conclusions: In order to achieve lower and more uniform values in terms of risk, we believe that it is necessary to employ a greater number of hours to the training of police officers on the use of force and also the convenience of conducting further studies on a larger and more representative sample of officers.

The world population is aging, which along with recent shifts in the labor force participation (LFP), is having a significant longevity influence on state pension programs across the board, including Canada, Finland, Japan, and Germany. Except Japan, these countries have set their statutory re-tirement age at 65, but the impact of aging workforce and declined fertility rates create wonders on the estimate future trends in the LFP, as well as the length of retirement. In this study, we fit the LFP rates of these countries, representing continents from Asia, Europe and North America among the OECD countries, using the Lee-Carter and Cairns-Blake-Dowd (CBD) stochastic models. The es-timates are then used for the projection of future LFP rates (1989-2066), and by combining the mortality forecasts from the United Nations, we project the expected length of retirement (1989-2066). This study provided a novel comparison between the Lee-Carter and the CBD LFP models by fitting and forecasting the LFP rates of senior employees between 50- to 74-year-olds. The results revealed disparities between models that provided proof of the presence of model risk for longer retirement durations. The study findings emphasized the importance for decision-makers in pension industry to have awareness of potential risks and limits associated with the LFP models. The Lee-Carter model outperformed the CBD model even though the CBD model is known for its ac-curate prediction in higher ages. Population aging should be considered in any analysis of the long-term viability of pensions, together with the participation rate trends for a sustainable labor market future.

Imaginary dimensions in physics require an imaginary set of base Planck units and some negative parameter $c_n$ corresponding to the speed of light in vacuum $c$. The second, negative fine-structure constant $\alpha_2^{-1} \approx -140.178$ present in Fresnel coefficients for the normal incidence of electromagnetic radiation on monolayer graphene leads to the imaginary Planck units. Furthermore, it sets $c_n \approx -3.06 \times 10^8~\text{[m/s]}$. It follows that electric charges are the same in real and imaginary dimensions. Neutron stars and white dwarfs, objects emitting perfect black-body radiation, need energy exceeding their mass-energy equivalence ratios. Complex energies are defined in terms of real and imaginary Planck units. Their imaginary parts, inaccessible for direct observation, store the excess of these energies. It follows that black holes are fundamentally uncharged, charged micro neutron stars and white dwarfs with masses lower than $5.7275 \times 10^{-10}~[\text{kg}]$ are unphysical, and the radii of white dwarfs' cores are limited to $R_{\text{WD}} < 6.7933~G M_{\text{WD}}/c^2$. It is conjectured that the maximum atomic number $Z=238$. A black-body object is in the equilibrium of complex energies of masses, charges, and wavelengths if its radius $R_\text{eq} \approx 2.7665~G M_{\text{BBO}}/c^2$, which corrects the value of the photon sphere radius $R_{\text{ps}}=3G M/c^2$, taking into account the value(s) of the fine-structure constant(s), which is otherwise neglected in general relativity.

In this paper, a mathematical and physical interpretation of the length and the angle of the catenary curve made by the anchor chains was implemented, and the safety of an anchored vessel was reviewed. So far, holding force has been calculated approximately when the angle of the catenary curve of the anchor chain to the seafloor is 0°. In this study, the holding force equation was strictly derived for the case of anchor dragging. In addition, the equations for the angle and length of the catenary curve were mathematically derived when the anchor dragging occurs. The holding force equation derived in this paper are expected to help provide guidelines in vessel design or increase the safety of anchoring.

Based on the panel data from 31 provinces in China from 2012 to 2020, this paper uses the TOPSIS method to measure the development level of the digital economy and environmental quality. Then, a coupled coordination degree model is used to analyse the relationship between the digital economy and environmental quality. Kernel density estimation and the Dagum Gini coefficient method were used to reveal the dynamic evolution trend of the coupled coordination level between the digital economy and environmental quality and the regional trends of coupled indicators. Finally, the dynamics of the above relations were explored with an econometric model. The results show that the coupled coordination degree of the digital economy and environmental quality displays obvious regional heterogeneity, and the national coordination level exhibits dynamic convergence characteristics. The heterogeneity of the coupled coordination degree of the two systems in the eastern region has decreased year by year, except in the western region, the central region and the northeast region, where an upwards trend is observed. Overall, the Gini coefficient of the coupled coordination degree between the digital economy and environmental quality displays a certain downwards trend. The level of economic development, technological innovation level, industrial structure, degree of opening to the outside world, degree of environmental regulation, marketization index and financial development level have a positive influence on the coupled coordination of the digital economy and environmental quality. Environmental regulation is the core driver of the coupling of the two systems, and the economic development level, technological innovation level, industrial structure and degree of openness are the other major drivers. Therefore, in the processes of digital economy transformation and environmental governance, all regions should focus on balanced development between regions to optimize the overall efficiency of the two systems, consider external influence, enhance internal capabilities, and promote the coordination and co-development of the two systems.

This paper is the third application-oriented paper based on the "unified theory of forces" and also addresses the shortcomings of previous research in fully explaining the origin and nature of the weak force. The main conclusions of this paper are as follows: (1) It is argued that neutrinos are generated by the gravitational field, and their generation mechanism is similar to the radiation of photons from electron orbital transitions. Particles undergoing orbital transitions in a gravitational field will emit neutrinos. (2) We rigorously derive the energy formula for neutrinos and demonstrate that the energy formula for neutrinos does not comply with the Planck energy formula. Neutrinos with higher energy have longer wavelengths and are more easily observed in experiments.

Pool boiling is extensively utilized in various fields, such as electronics cooling, battery cooling, nuclear power plants, and chemical processing. In the process of temperature control through boiling, the generation and transportation of bubbles play a crucial role in calculating the heat transfer capacity of the system. Therefore, it holds immense significance to gain a profound understanding of the mechanisms underlying bubble formation, growth, and detachment. Currently, numerous mechanistic explanations and empirical correlations have been proposed to elucidate various parameters of bubbles during the boiling process. These findings were considered valuable references in selecting appropriate boiling media and designing efficient heating surfaces. To comprehensively present the progress of bubble formation and heat transfer during the boiling process, the forces exerted on the bubbles was highlighted in this article. And a meticulous review on bubble force analysis and correlation formulas pertaining to various relevant parameters (e.g. nucleation sites density, bubble growth rate, detachment diameter, detachment frequency) were conducted. This review article also were expected to provide a novel foundation for further exploration of enhanced boiling heat transfer.

Modern imaging strategies are paramount to studying living systems such as cells, bacteria, and fungi and their response to pathogens, toxicants, and nanomaterials as modulated by exposure and environmental factors. The need to understand the processes and mechanisms of damage, healing and cell survivability of living systems continues to motivate the development of alternative imaging strategies. Of particular interest is the use of label-free techniques that minimize interference of biological processes by foreign marking substances and reduce intense light exposure and potential photo-toxicity effects. This review focus on the potential synergic capabilities of atomic force microscopy (AFM) as a well-developed and robust imaging strategy with demonstrated applications to unravel intimate details in biomedical applications, with the label-free, fast, and enduring Holotomographic Microscopy (HT) strategy. We first review the operating principles that form the basis for the complementary details provided by these techniques regarding the surface and internal information provided by HT and AFM is essential and complimentary for the development of several biomedical areas studying the interaction mechanisms of nanomaterials with living organisms. First, AFM can provide superb resolution on surface morphology and biomechanical characterization. Second, the quantitative phase capabilities of HT enable superb modeling and quantification of the volume, surface area, protein content, and mass density of the main components of cells and microorganisms, including morphology of cells in microbiological systems. These capabilities result from directly quantifying refractive index changes without requiring fluorescent markers or chemicals. As such, HT is ideally suited for long-term monitoring of living organisms in conditions close to their natural settings. We present a case-based review of the principal uses of both techniques and their essential contributions to nanomedicine and nanotoxicology, emphasizing cancer and infectious disease control. The synergic impact of the sequential use of these complementary strategies provides a clear drive for adopting these techniques as interdependent fundamental tools.

A friction loss model for brake testing platform is constructed to revise the braking force test results, which can largely improve the accuracy of automotive brake performance testing. Specifically, the influence of tire pressure, vehicle axle load, placement angle and vehicle speed on the friction loss is tested and analyzed on a wheelbase adjustable automotive anti-force brake testing platform. The friction loss model for the platform is constructed based on the defined relative slip and placement angle, which is validated through actual tests on four types of vehicles. The results showed that the maximum relative error between the values of the model calculated simulation and the measured was 2.2%, indicating the friction loss model is valid and can provide a basis for revising the braking force of automotive brake. Meanwhile, the maximum braking force increases from 3982 N to 4772 N, increased by 19.8%, when the placement angle increased from 36.9° to 47.0°. Accordingly, in order to improve the accuracy of detection results of the automotive anti-force rolling brake testing platform, the friction loss caused by the change in the placement angle should be revised, and then braking rate of the vehicle should be judged according to GB 7258-2017 and GB 38900-2020.

The Review examines studies aimed at the organization of energy (non-mechanical) control of high-speed flow/flight using spatially multi-component plasma structures and combined energy deposition. The Review covers selected works on experimental obtaining and numerical modeling multi-component plasma structures and use of sets of actuators based on the plasma of such a spatially type for the purposes of control of shock wave/bow shock wave – energy source interaction, as well as control of shock wave – boundary layer interaction. A series of works on repetitive multiple laser pulse plasma structures is also analyzed from the point of view of examining shock wave/bow shock wave boundary layer interaction. Self-sustained theoretical models for laser dual-pulse, multi-mode laser pulses and self-sustained glow discharge are also considered. Separate sections are devoted to high-speed flow control using combined physical phenomena and numerical prediction of flow control possibilities using thermal longitudinally layered plasma structures. The wide possibilities for organization and applying spatially multi-component structured plasma for the purposes of high-speed flow control are demonstrated.

Existing research concerning the effects of the sitting birth position during the second stage of labour on maternal and neonatal outcomes remains controversial, and there is a lack of studies to explore its effect on the childbirth experience. The objective of this study is to explore whether the sitting birth position would influence maternal and neonatal outcomes, as well as the childbirth experience reported by Chinese women using the Childbirth Experience Questionnaire (CEQ). A total of 296 women (including primiparous women and multiparous women) were enrolled in our study, and they were divided into the sitting position cohort (n=106) or the lithotomy position cohort(n=116). The study found that primiparous women in the sitting position cohort had a shorter duration of the second stage of labour, higher spontaneous vaginal birth rates, lower episiotomy rates and better childbirth experience (p<0.01). There was no significant difference for perineal lacerations, 2h-postpartum haemorrhage (P>0.05) between the two cohorts of primiparous women. After adjusting for confounding factors through multiple linear and logistic regression analyses, the results remained consistent with those reported above. No neonate in each cohort had Apgar scores at 1min and 5 min postpartum less than 7 or the Cord artery pH less than 7.00, regardless of parity. In addition, among multiparous women, there was no significant difference in any maternal and neonatal outcomes and women’s CEQ scores (p>0.05) between two cohorts. Based on the findings, we recommend that women could take the sitting birth position into account when giving birth for a positive childbirth experience, especially for primiparous women. The study could also serve as a reference for healthcare providers in the management of childbirth positions and the development of high-quality maternal care.

This study presents a combined electrochemical impedance spectroscopy (EIS) and atomic force microscopy (AFM) and Scanning Kelvin Probe Force Microscopy(SKPFM) investigation on the natural passivation process of stainless steels (AISI 316 and AISI 304) and nickel-based alloy (INCONEL 600) as a function of immersion time in an alkaline medium (pH = 13). EIS measurements show an increase in the resistance of the film with increasing immersion time in the electrolyte. After 3 days of immersion, for the three alloys, the films formed constitute an effective barrier to the dissolution of the alloys as shown by AFM and SKPFM. The oxide film growth on each substrates is only influenced by trenches formed during the polishing step and don’t depend on the chemical composition.

In an era marked by rapid technological progress and global dynamics, the Neo-Language Acquisition and Learning Theory challenges conventional language acquisition paradigms through its conceptualization of 'Grit: The Unyielding Will to Connect,' emphasizing determination, motivation, and adaptability as the primary drivers of language learning, transcending age-related constraints and critical periods. This theory also underscores 'Self-Preservation: Language as the Canvas of Reality,' as language plays a pivotal role in preserving and conveying our individual and collective experiences. Recent global events have underscored the theory's relevance, prompting a reevaluation of language education in response to changing circumstances. Moreover, 'Techno-Training: Language Acquisition and Learning in the Digital Age' is integral to the theory, as it recognizes the influence of technology on modern language education. Beyond traditional methods, these three reshape our fundamental understanding of said theory. Drawing from historical evidence, psychological principles, and contemporary applications, they supported the conceptualization of the theory itself. Overall, the Neo-Language Acquisition and Learning Theory revolutionizes language education, spotlighting the power of motivation, determination, and adaptability to navigate the evolving landscape of language learning and acquisition.

Background Ultrasonographic measurement of the optic nerve sheath diameter (ONSD) is helpful in the assessment of intracranial pressure. The aim of this study was to determine whether the Trendelenburg position during laparoscopic urological surgery changed the ONSD and whether changes correlated with postoperative complications. Methods In this prospective study, we measured ONSD before patients were placed in the Trendelenburg position. Then the Trendelenburg position was established by tilting the operating table to 20-25 degrees. After surgery, the patients were placed in a horizontal position, and the second measurement of ONSD was obtained. Results The study included 69 patients. The average preoperative ONSD in the right eye was 5.8 ± 0.7 mm and 5.8 ± 0.8 mm in the left eye. The average postoperative ONSD in the right eye was 6.6 ± 0.8 mm and 6.6 ± 0.7 mm in the left eye. The differences between postoperative and preoperative values in the right and left eyes were statistically significant (p <0.000001). ONSD increases above the norm did not correlate with the incidence of postoperative nausea (p = 0.94), delirium (p = 0.81), or the time to patient awakening (p = 0.29). Conclusion ONSD increased in patients who underwent surgical procedures performed in the Trendelenburg position, but the increase did not correlate with postoperative complications.

Neat polyimide films are known to be dense and rigid. They are therefore not suitable for use in membranes, sensors and sustainable energy storage applications. In this study a novel technique has been used to simulta-neously improve the rigidity, damping ability and impact resistance of polyimide membranes. It is demonstrated that dispersion of a small amount of polyaniline copolymer-modified clay of about 0.25-0.5 wt.% into the pol-yimide matrix, resulted in enhanced storage modulus while maintaining high damping ability and glass transition temperature, Tg. Novel polyimide/substituted polyaniline-copolymer-clay nanocomposite membranes containing poly(N-ethyl-aniline-co-aniline-2-sulfonic-acid-modified-clay (SPNEAC) was successfully prepared and in-corporated into polyimide matrix to form modified clay/polyimide nanocomposites. UV-Vis analysis of the nanocomposite films show that the optical transparency of the SPNEAC-PI nanocomposite membranes de-creased with increasing SPNEAC concentration due to the high UV-Vis absorption of SPNEAC. Transmittance of about 3 % was observed in the nanocomposite membrane containing 5wt.% modified clay at 500 nm wave-length, which is significantly lower than that for the neat PI membrane of about 36 %. The dispersion of SPNEAC containing high concentration of clay (≥ 40 wt.% clay), SPNEAC2 in polyimide matrix, resulted in attainment of a higher degree of imidization than was possible for the neat organoclay/polyimide nanocomposite. This behavior is believed to be due to the synergistic interaction between PI and polyaniline copolymer modified clay. The viscoelastic property of polyimide and the nanocomposite membranes was measured by using the dynamic mechanical spectroscopy, DMS. It was shown that the glass transition temperature, Tg of the nano-composites decreased, while the damping ability and impact energy increased with increasing weight fraction of fillers.

Despite their anti-icing ability, hydrophobic coatings have the disadvantages of easy falling off and poor wear resistance, resulting in insufficient durability of ice/snow melting. To improve the surface stability and durability of superhydrophobic coatings, nanoparticle/epoxy coatings were prepared with three types of nanoparticles, two types of dispersion methods, three types of application methods and two types of introduction methods of epoxy resin. Water contact angles, ice adhesion force and icing rate of asphalt concrete coated with hydrophobic coatings were tested. The molecular structures of coatings were analyzed by Fourier transform infrared spectroscopy. The surface morphology of hydrophobic coatings was observed using Scanning electron microscopy. Results indicated that nano-ZnO, TiO2 and SiO2 particles can be modified into hydrophobicity by stearic acid. The hydrophobic coating could improve the hydrophobicity of concrete, reduce the adhesion strength of ice and asphalt concrete and delay the beginning icing time. Moreover, The dosages of stearic acid, nanoparticle and epoxy resin need to be in a certain range to ensure the best hydrophobicity and durability of coatings.

We studied the magnetostriction coefficients, λs, Curie temperature, Tc, and their dependence on annealing conditions in Fe47Ni27Si11B13C2 and Co67Fe3,9Ni1,5B11,5Si14,5Mo1,6 amorphous glass-coated microwires with rather different character of hysteresis loops. A positive λs≈20x10-6is observed in as-prepared Fe47Ni27Si11B13C2, while low and negative λs ≈-0.3x10-6 is ob-tained for Co67Fe3,9Ni1,5B11,5Si14,5Mo1,6 microwire. Annealing affects the magnetostriction coeffi-cients and Curie temperatures, Tc, of both Fe47Ni27Si11B13C2 and Co67Fe3,9Ni1,5B11,5Si14,5Mo1,6 glass-coated microwires in a similar way. Observed dependencies of hysteresis loops, λs and Tc on annealing conditions are discussed in terms of superposition of internal stresses relaxation and structural relaxation of studied microwires. We observed linear λs dependence on applied stress, σ, in both studied microwires. A decrease with applied stress is observed for Co-rich mi-crowires with negative magnetostriction coefficient. In contrast, a linear increase of the magne-tostriction coefficient with applied stress is observed for Fe-Ni- rich microwires with positive magnetostriction coefficient. Observed results are discussed in terms of influence of internal stresses and short range atomic rearrangements induced by annealing on hysteresis loops, magnetostriction coefficients and Curie temperatures of studied microwires.

The Casimir–Lifshitz friction force and the heating rates of two metal plates with a narrow vacuum gap between them during nonrelativistic motion of one of them are calculated analytically and numerically within the framework of fluctuation electrodynamics. Changes in material properties are taken into account using the Bloch-Grüneisen and modified Bloch-Grüneisen (with finite residual resistance) resistivity models within the Drude approximation. It is shown that identical plates with the same initial temperature have the same heating rate, determined by the power of the friction force, and the possibility of measuring the friction force from the heating kinetics of nonmagnetic metal plates with temperatures of 1–10 K is substantiated.

Using graph theory, computer aided motion, static force and power flow analysis of planetary gear mechanism is realized. The motion, static force and efficiency calculations of 6HP26 automatic transmission are carried out. Based on kinematic and static force analysis model, related matrices are acquired. Hence, kinematic and static force analysis of planetary gear mechanism is achieved. The link power can be determined by the link speed and torque. Power flow diagrams of each gear are acquired. The efficiency is calculated by transmission ratio method.

Psychological readiness following Anterior Cruciate ligament Reconstruction (ACLR) correlates with different return to sport outcomes. However, the relationship between strength and power and psychological readiness remains unexplored. The aim of this study was to investigate the relationship between the Anterior Cruciate Ligament Return to Sport After Injury (ACL-RSI) scores and various hamstrings and quadriceps strength and power variables. Twelve participants (20.7±2.5 years old; 174.2±7.5 cm; 70.2±8.5 kg; 18.2±8.3% of body fat) who had an ACLR nine months or more before the study completed the ACL-RSI questionnaire and isokinetic strength testing of the hamstrings and quadriceps (60°.s-1 and 180°.s-1). Based on ACL-RSI scores, they were divided into “cases” and “controls”, deemed not psychologically ready and psychologically ready to return to previous sport performance (PILOS), respectively. The main findings are that quadriceps’ and hamstrings’ rate of torque development (RTD) and time since surgery were determinants of psychological readiness following ACLR. Furthermore, compared to controls cases showed significantly lower angle-specific quadriceps and hamstrings torque close to extension and lower RTD, but no difference in peak torque. These results suggest that physiotherapists should facilitate athletes’ RTS by focusing on the restoration of RTD and strength at angles close to full knee extension.

This study aims to explore predictors of the foreign investment from China coming into Rwanda. One of the components of Rwanda’s economy is the investment it receives from other countries. In order to achieve these objectives, the study gathers econometric secondary data from 2007 to 2020 quarterly which were availably provided by National Statistics of China, World Bank, UNCTAD, National Institute of Statistics of Rwanda, and the National bank of Rwanda. From literature and based on the availability of data, market size, trade openness, infrastructure, and human capital were measured as predictors of Chinese FDI. The data is analyzed using linear regression in Stata. The finding of the study showed that variables have a positive effect on FDI from China, and it found that though FDI had an effect on overall economy of Rwanda, the effect was not statistically significant. The study suggested that Rwanda’s policy on foreign investment should aim to attract and encourage Chinese investment to increase the economy of Rwanda. To encourage more FDI, the Rwandan government can offer Chinese investors greater ownership, locational, and internalization benefits. It also should continue to strengthen economic policy transparency since it lowers transaction costs and hence improves incentives for foreign investment.

When a suspension passes through a high-frequency standing sound wave, the particles it contains are manipulated by acoustic forces. In a one-dimensional sound field, these forces lead to a planar arrangement of the particles and the formation of agglomerates. It is known that the combination of these forces and depth filtration can be utilized to significantly increase the filter efficiency of coarse-pored media. So far, this concept has only been used in microfluidics. In this paper, we present the results of a scaled-up filtration channel to test the viability of the industrial application of acoustically assisted filtration systems for the removal of microparticles. The influences of acoustic power input, flow rate, and the porosity of the filter media are investigated. In addition to verifying the scalability, a significant decrease in the large particle fraction in the outflow of the channel was observed when a high-power sound field is applied. Furthermore, the formed agglomerates tend to rise to the fluid surface. The floating particles mostly consist of a large particle fraction.

Electro-mechanical braking(EMB) which represents development direction of autonomous and intelligent braking plays very useful role on enhancing the braking response performance and intelligence level for mine underground electric trackless rubber-tired vehicle (ETRV). However,there is no Electro-Mechanical Brake system applied practically in coal mine UTRV until now.The accurate control of braking clamping force can determine the length and precision of braking distance of mine ETRV.In addition,because of poor working conditions in underground coal mine tunnel ,braking clamping force sensor may be easy to occur failure,which may cause vital accident.Therefore,A cascaded three-closed-loop EMB system with a positive clamping force sensor or force estimator built for ETRV is established to achieve autonomous elimination and reset of braking clearance and reliable braking force tracking ability via utilizing the electro motor rotor angle displacement and hysteresis effect of mechanical components in this EMB.The results of simulation and experiment indicate that clamping force response is faster than traditional hydraulic disk braking system and proposed force estimator presents good fault-tolerant ability when sensor is fault.This EMB can replace the current hydraulic brake system to enhance automation level of braking control for ETRVs and braking force response performance, reduce oil pollution and cost of maintenance, which is also key technology support for really precise motion control of mine autonomous driving vehicles.

In this report, we establish a straightforward method for estimating the equilibrium constant for the CK reaction over wide but physiologically and experimentally relevant ranges of pH, Mg2+ and temperature. Our empirical formula for CK Keq” is based on experimental measurements. It can be used to estimate [ADP] when [ADP] is below the resolution of experimental measurements, a typical situation because [ADP] is on the order of micromolar concentrations in living cells, and may be much lower in many in vitro experiments. Accurate prediction of [ADP] is essential for in vivo studies of cellular energetics and metabolism, and for in vitro studies of ATP-dependent enzyme function under near-physiological conditions. With [ADP], we could estimate ΔGATP. Application to actomyosin force generation in muscle provides support for the hypothesis that, when [Pi] varies but not when pH is altered, maximum Ca2+-activated isometric force depends on ΔGATP in both living and permeabilized muscle preparations. Further analysis of the pH studies introduces a novel hypothesis for the role of submicromolar ADP in force generation.

Balance requires constant adjustments in muscle activation to attain force steadiness. Creating appropriate training can be challenging. The purpose of this study was to examine the effects of two weeks front squat instability training using a water-filled training tube on force steadiness during an instability challenge. Control (CON, n= 13) and experimental (EXP, n=17) subjects completed pre and post testing for EMG variability by completing one set of 10 repetitions with a stable and unstable training tube. Electrodes were placed bilaterally on the anterior deltoid, paraspinal and vastus lateralis muscles. CON subjects completed 2 weeks of training using a stable training tube, while EXP subjects trained with a water-filled instability tube. EMG data were integrated for each contraction and force steadiness computed using the natural log of coefficient of variation. CON results showed no changes in force steadiness for any condition. EXP showed significant reductions in EMG activation variability across all muscles. These results indicate a significant training effect in reducing muscle activation variability in subjects training with a water-filled instability training device. Improvements seen in these healthy subjects supports development of training implements for a more clinical population to help improve force steadiness.

PIEZO channels PIEZO1 and PIEZO2 are the newly identified mechanosensitive, non-selective cation channels permeable to Ca2+. In higher vertebrates, PIEZO1 expresses ubiquitously in most of the tissues and cells while PIEZO2 expresses more specifically in the peripheral sensory neurons. PIEZO channels contribute to a wide range of biological behaviors and developmental processes, therefore driving a significant attention in the effort to understand their molecular properties. One prominent property of PIEZO channels is their rapid inactivation, which manifests itself as a decrease of channel open probability in the presence of a sustained mechanical stimulus. Lack of the PIEZO channel inactivation is linked to various mechanopathologies emphasizing the significance of studying this PIEZO channel property and the factors affecting it. In the present review, we discuss the mechanisms underlying the PIEZO channel inactivation, its modulation by interaction of the channels with lipids and/or proteins, and how the changes of PIEZO inactivation by the channel mutations can cause a variety of diseases in animals and humans.

Barrier coverage is a fundamental application in wireless sensor networks, which is widely used to protect a region through intruder detection for smart city. In this paper, we study a new branch of barrier coverage, named warning barrier coverage (WBC). Different from the classic barrier coverage, WBC has the inverse protect direction, which protects unexpected visitors by warning them away from the region enclosed by sensor barriers. The WBC holds a promising prospect in many danger keep out applications for smart city. For example, a WBC can enclose the debris area in the sea and alarm any approaching ships in order to avoid their damaging propellers. One special feature of WBC is that the target region is usually dangerous and its boundary is previously unknown. Hence, the scattered mobile nodes need to detect the boundary and form the barrier coverage themselves. It is challenging to form these distributed sensor nodes into a barrier because a node can sense only the local information and there is no global information of the unknown region or other nodes. To this end, we propose a novel solution AutoBar for mobile sensor nodes to automatically form a WBC for smart city. To pursue the high coverage quality, we theoretically derive the optimal distribution pattern of sensor nodes using convex theory. Based on the analysis, we design a fully distributed algorithm that enables nodes to collaboratively move towards the optimal distribution pattern. In addition, AutoBar is able to reorganize the barrier even any node is broken. To validate the feasibility of AutoBar, we develop the prototype of the specialized mobile node, which consists of two kinds of sensors: one for boundary detection and another for visitor detection. Based on the prototype, we conduct extensive real trace driven simulations in various smart city scenarios. Performance results demonstrate that AutoBar outperforms the existing barrier coverage strategies in terms of coverage quality, formation duration, and communication overhead.

We propose a description of the electromagnetic field in the form of a four-component complex spinor, from which a vector of electromagnetic potential with two degrees of freedom, calibrated by two conditions - zero length and zero component along the y-axis - is obtained by using Pauli matrices. A similar approach is applied to the field of a fermion, in particular, the electron. It is known that the quantum field of the electron and the electron itself is a four-component complex spinor, so, existing in the Minkowski vector space, we cannot observe it directly. But with the help of Pauli matrices a vector is formed from the electron spinor, which is known to us as an electric current vector, and this current vector describes exactly a single particle. As a vector, it is available to us for observation in our vector space. Similarly, the electromagnetic field and its photon particle is also a four-component spinor, from which the universal formula using Pauli matrices produces a vector, it is known to us as the electromagnetic potential vector, and it too describes even a single photon. All the differences in the properties of the current vector and the electromagnetic potential vector, and hence the electron and the electromagnetic field, are due only to a slight difference in the structures of their four-component spinors and inextricable linked to them momentum spinors and coordinate spinors. Expressions for the electric and magnetic fields of a photon during its interaction with an electron.Thus, a unified way to describe bosons and fermions in spinor space is proposed. Each spinor using the same formula corresponds to a vector, in the case of a fermion it is a current vector, in the case of a boson it is a vector, for example, of the electromagnetic potential. Each spinor of a field is matched with a spinor of coordinates and a spinor of momentum, which are transformed by the same Lorentz transformations and which have the same structure as their corresponding field spinor, that is, the momentum and coordinates of boson have a bosonic spinor structure, while momentum and coordinates of fermion are a spinor with a fermionic structure. Field, coordinates and momentum vectors of boson automatically have a zero length, while in the case of fermion they all have a nonzero length, so the fermion, in contrast to the boson, has a nonzero mass, nonzero charge and moves with a sub light speed.While quantum mechanics treats probability as a real number, quantum field theory deals with probability as a four-dimensional real vector. The place of the probability amplitude, which in quantum mechanics is a complex number, in quantum field theory is taken by a complex spinor.In the same way as in quantum mechanics the processes of propagation and interaction are described at the level of complex probability amplitudes, and the final result is translated into a real probability value, so in quantum field theory all processes should be described in terms of complex spinor space, and the result is translated into the form of a real vector in Minkowski space.The presented approach, at its proper development, makes it possible to carry out calculations of the interaction of particles in two-dimensional spinor space, and to interpret in terms of the Minkowski vector space only the final results.

The healthy function of the vestibular system (VS) is of vital importance for individuals to carry out their daily activities independently and safely. This study carries out Tsallis entropy (TE)-based analysis on insole force sensor data in order to extract features to differentiate between healthy and VS-diseased individuals. Using a specifically developed algorithm, we detrend the acquired data to examine the fluctuation around the trend curve in order to consider the individual’s walking habit and thus increase the accuracy in diagnosis. It is observed that the TE-value increases for diseased people as an indicator of the problem of maintaining balance. As one of the main contributions of this study, in contrast to studies in the literature that focus on gait dynamics requiring extensive walking time, we directly process the instantaneous pressure values, enabling to reduce the data acquisition period significantly. The extracted feature set is then inputted into fundamental classification algorithms, with the Support-Vector-Machine (SVM) demonstrating the highest performance, achieving an average accuracy of 95%. This study constitutes a significant step of a large project aiming to identify specific VS disease together with its stage. The performance achieved in this study provides a strong motivation to further explore this topic.

The elastic wave equation with the seismic tensorial force is solved in a homogeneous and isotropic medium (the Earth). Spherical-shell waves are obtained, which are associated to the primary P and S seismic waves. It is shown that these waves produce secondary waves with sources on the plane surface of a half-space, which have the form of abrupt walls with a long tail, propagating in the interior and on the surface of the half-space. These secondary waves are associated to the seismic mainshock. The results, previously reported, are re-derived by using Fourier transformations and specific regularization procedures. The relevance of this seismic motion for the ground motion, the seismographs' recordings and the effect of the inhomogeneities in the medium are discussed.

In light of the current situation where no testing equipment is available for measuring thermal deformation of objects, this paper proposes a novel method for accurate and precise measurement. The method overcomes the limitations of previous approaches that relied on pitch angle. By utilizing the principle of biplane multiple reflections, a bivariate laser spot displacement analysis algorithm is devised to attain highly precise measurements of bivariate angles. Additionally, a temperature gradient comparison algorithm is introduced to calculate the indicator test results under specific temperature conditions. To validate the effectiveness and reliability of this method, a testing system is constructed and utilized. The results demonstrate that the thermal deformation angle change test achieves an impressive accuracy of 0.015″ and a rate of thermal deformation angle change of 0.3247″/°C. These values are in close agreement with the previously simulated analysis result of 0.359″/°C, with only a relative error of 9.55%. Therefore, the test results confirm the efficacy and reliability of this testing method along with the feasibility of the algorithm processing.

In Ethiopia, land degradation in the form of gully development and soil nutrient depletion is a very serious issue. The goal of this study is to determine how different types of land management practices and slope positions affect particular soil physico-chemical characteristics in the Agamssa watershed. Using systematic sampling techniques, soil samples were taken using a sampling quadrat (15 * 15 m) that was placed 50 m apart from one another. A total of 54 quadrats were planted at three slope positions: upper (>15%), middle (10–15%), and foot (3–10%) slope respectively. 18 composite soil samples were then. A two-way ANOVA was used to analyze the data, and the Least Significant Difference (LSD) test was used to separate the means at p ≤ 0.05. According to the study's findings, the value of most soil physical and chemical characteristics was higher in closed area than on open grazing land, as well as at foot slope position compared to middle and upper slope positions. The higher mean value (7.3 ppm) was recorded at the foot slope, while the lower mean value (4.9 ppm) was found at the upper slope position. The exchangeable cations such as Mg+2, K+, and Na+ were significantly (p≤ 0.01) affected by the main effect of land-use types. The higher mean values of Mg+2 (9.70 mq/100g), K+ (0.38 mq/100 g), and Na+ (0.035 mq/100 g) were found at area closure, whereas the lower mean values of Mg+2 (7.33 mq/100g), K+ (0.30 mq/100 g), and Na+ (0.027 mq/100g) were recorded at open grazing land. It was able to conclude this study that area closure enhances the physical and chemical qualities of soil and recovers woody plant species. Therefore, converting open grazing land into a closure area is advised.

In this study, we investigated, for the first time, the effects of the spatially varying effective mass, asymmetry parameter, and well width on the electronic and optical properties of the quantum well which has an improved Rosen-Morse potential. Calculations are made within the framework of the effective mass and parabolic band approximations. We have used the diagonalization method by choosing a wave function based on the trigonometric orthonormal functions to find eigenvalues and eigenfunctions of the electron confined within the improved Rosen-Morse potential. Our results show that the position-dependence mass, asymmetry, and confinement parameters cause significant changes in the electronic and optical properties of the structure we focus on since these effects create a significant increase in electron energies and a blue shift in the absorption spectrum. The increase in energy levels enables the development of optoelectronic devices that can operate at wider wavelengths and absorb higher energy photons. This offers potential advancements in fields such as optical communication, imaging technology, and solar cells.

Cancer cells exhibit aberrant extracellular matrix mechanosensing due to altered expression of mechanosensory cytoskeletal proteins. Aberrant mechanosensing of the tumor microenvironment (TME) by cancer cells has been shown to be associated with cancer development and progression. Recent studies show that altered mechanosensing changes the mechanobiological properties of cells, and, in turn, cells become susceptible to mechanical perturbations. Due to an increasing understanding of cell biomechanics and cellular machinery, several approaches have emerged to target the mechanobiological properties of cancer cells and cancer-associated cells to inhibit cancer growth and progression. In this review, we summarize the progress that happened in the development of mechano-based approaches to target cancer by interfering with the cellular mechanosensing machinery and overall TME.

Analytical modeling has symmetries and aesthetic-mathematical characteristics that distinguish it from numerical computation. Nanoscience plays an extremely important role in unification efforts that also include holistic aspects of reality. In this paper I present new discovered results about the complete analytical quantum relativistic form of the mean square deviation of position false related to a lately appeared Drude-Lorentz-like model (DS model), already performed at classical, quantum and relativistic level. The function false gives precise information about the distance crossed by carriers (electrons, ions, etc.) inside a nanostructure, considering both quantum effects and relativistic velocities. The model has a wide scale range of applicability; the nanoscale is considered in this paper, but it holds from sub-pico-level to macro-level because of the existence of a gauge factor, making it applicable to every oscillating processes in Nature. Examples of application and suggestions supplement the paper, as well as interesting developments to be studied related to the model and to one of the basic elements of a current unified holistic approach based on the vacuum energy.

In view of the limitations of the existing optimization method of suspender cable force, in order to improve the stress of suspender under completion state and avoid frequent adjustment of cable force and grid beam elevation during construction, a new method of cable force optimization is proposed. The article takes the longest large span arch bridge in the world, Pingnan Third Bridge, a Concrete-filled steel tube (CFST) arch bridge with a span of 575m as the engineering background combined with the finite element analysis and multi-objective optimization method. One cable force optimization method that suspender “Real-time correction during construction, in the process variable optimal and results reliable” during panel girder lifting of long span CFST arch bridges is clarified. Taking the panel girder weight and displacement during the construction as parameter variables, the displacement and unevenness of the panel girder under completion state as constraint conditions, the displacement and cable force during the hoisting construction as the objective equation, through the optimization of the objective equation, the suspender cable force and dis-placement of each hoisting section are calculated. The results show that it is feasible to introduce the optimization theory into the cable force optimization when lifting the panel girder. the segment displacement variation is minimized to meet the destination. The cable force distributed evenly under completion state of the bridge that further making sure the completion state satisfies the requirements. No repeating iteration is needed, thus avoiding cumberso me calculation, getting cable force once. With higher optimization efficiency and better effects, the method provides high value for the cable force calculation of same type bridge suspender construction and for guiding construction.

Employing numerical methods to simulate manufacturing processes and study their influential factors is increasing. The development of computers and engineering software has increased the ability and accuracy of numerical methods in simulating various aspects of different processes. One of the manufacturing processes that has been considered by many industries in recent years to join metals in solid-state with unique properties is called friction stir welding. It is challenging and, in some cases, impossible to experimentally study the various aspects of this process, such as temperature distribution, stress distribution, and material flow, due to severe plastic deformation in the weld zone. In this case, numerical methods are used to investigate these parameters and better understand the process. This study first investigates various numerical methods researchers use to simulate the process. The ability, pros, and cons of these methods to simulate the process are also examined. Then, the applications of numerical models in simulating the temperature distribution during the process as well as the effects of input parameters on the temperature history of the process, are deeply considered. Next, the application of numerical methods in material flow modeling during the process is investigated. Finally, the modeling of the microstructure of the welding zone is investigated using numerical methods that help significantly in predicting the weld microstructure.

The purpose of this study was to investigate the horizontal force and contribution of shoulder horizontal adductor and elbow extensor muscles activity during wide and narrow grip bench press (BP) in various conditions, such as resistance trained/non-trained, concentric/eccentric and muscle fatigue/non-fatigue.　We measured the horizontal force on the bar and the electromyographic (EMG) muscle activity of pectoralis major (PM) and triceps brachii (TB) during 10RM BP with wide grip (81cm) and narrow grip (40cm)　in 7　resistance trained men and 7 non-trained men. The all-reps average of the horizontal to vertical force ratio both in resistance trained and non-trained subjects was about 30% outward for the wide grip, and about 10% inward for the narrow grip. The EMG contribution ratio PM/TB shows no significant differences between narrow and wide grip in all evaluated conditions except in non-trained subjects muscle fatigue eccentric phase. Both resistance trained and non-trained subjects did not push the bar straight upward, and the EMG PM/TB was almost unchanged by hand width. The direction adjustment of the force on the bar that achieves almost the same muscle activity degree of the shoulder and elbow joints might be optimal BP kinetics.

The safe and efficient mining of coal seams with low porosity, low permeability and high inhomogeneity under complex geological conditions is a major challenge, among which the permeability of coal seams is crucial for coal mine gas extraction. The development of coal seam permeability enhancement technology can help coal mines to produce safely and efficiently, and the extracted coal bed methane can be utilized as a green energy. In order to study the effect of freezing and thawing on the evolution of mechanical and permeability properties of coal, triaxial permeability tests were carried out on low-permeability coal under two kinds of surrounding pressures. At the same time, dry, saturated and freeze-thaw coal were set up for comparison, and the effects of water and freeze-thaw were separated from each other. The triaxial mechanics and percolation laws of dry, saturated and freeze-thaw coal rocks were obtained, and the mechanism of the influence of freeze-thaw on the permeability evolution law of coal was revealed. The research results can provide theoretical guidance for the gas extraction technology of low permeability coal seams with increased permeability.