In the face of the burgeoning electricity demands and the imperative for sustainable development amidst rapid industrialization, this study introduces a dynamic and adaptable framework suitable for policy-makers and renewable energy experts working on integrating and optimizing renewable energy solutions. While using a case study representative model for Sub-Saharan Africa (SSA) to demonstrate the challenges and opportunities present in introducing optimization methods to bridge power supply deficits and the scalability of the model to other regions, this study presents an agile multi-criteria decision tool that pivots on four key development phases, advancing upon established methodologies and pioneering refined computational techniques, to select optimal configurations from a set of Policy Decision Making Metrics (PDM-DPS). Central to this investigation lies a rigorous comparative analysis of variants of three advanced algorithmic approaches: Swarm-Based Multi-objective Particle Swarm Optimization (MOPSO), Decomposition-Based Multi-objective Evolutionary Algorithm (MOEA/D), and Evolutionary-Based Strength Pareto Evolutionary Algorithm (SPEA2). These are applied to a grid-connected hybrid system, evaluated through a comprehensive 8760-hour simulation over a 20-year planning horizon. The evaluation is further enhanced by a set of refined Algorithm Performance Evaluation Metrics (AL-PEM) tailored to the specific constraints. The findings not only underscore the robustness and consistency of the SPEA2 variant over 15 runs of 200 generations each, which ranks first on the AL-PEM scale but also validate the strategic merit of combining multiple technologies and empowering policymakers with a versatile toolkit for informed decision-making.

When a grid-forming (GFM) inverter is connected to a low or medium voltage weak power grid, the line impedance with resistive-inductive characteristics will cause power coupling. Typical GFM decoupling control strategies are designed under nominal line impedance parameters. However, there are deviations between the nominal line impedance and actual parameters, resulting in poor decoupling effects. Aiming at this problem, this paper proposes a power decoupling strategy based on a reduced-order extended state observer (ESO). Firstly, the power dynamic model of GFM is established based on the dynamic phasor method. Then, the model deviation and power coupling due to line impedance parameter perturbation are estimated as internal disturbances of the system, and the disturbances are compensated on the basis of typical power control strategy and virtual impedance decoupling. Good decoupling performance is obtained under different impedance parameters, improving the control strategy's robustness. Finally, the effectiveness of the proposed method is verified by the results of RT Box hardware-in-the-loop experiments.

The electric vehicle (EV) industry is experiencing rapid growth, accompanied by continuous advancements in charging infrastructure to satisfy the rising need for fast and reliable charging. Particularly, the focus has shifted towards EV fast charging (EVFC) and its impact on the power grid. This paper presents a comprehensive analysis and survey of scholarly literature and projects conducted in this field over the past decade. The findings highlight the rising demand for EVFC and the need to address its potential adverse effects on the power grid. However, there is a noticeable lack of clear research guidance regarding charging time. To tackle these challenges and pave the way for future solutions, extensive research on DC fast charging, ultra-fast charging, and the integration of vehicle-to-grid (V2G) systems is required. This review paper thoroughly investigates the development of fast charging technology for electric vehicles (EVs), including its advantages and comparative analyses from various perspectives. Furthermore, it delves into the advancements in DC fast charging infrastructure, emphasizing charging standards and control modes. The study also investigates different categories of battery chargers for both on-board and off-board charging. Additionally, it explores the classification of DC-DC converters in the context of DC fast charging stations, discusses control strategies for EV systems, identifies existing challenges, and outlines future trends in EV fast charging.

Boost-derived converters are most popular in Power Factor Correction AC-DC conversion applications and alternative energy generation systems. The proper operation of such converters relies on housekeeping power supplies providing auxiliary power for their control circuitry. The purpose of this study is to present a design-oriented analysis of a simple, passive, isolated, self-bias circuit that can provide a stabilized voltage for the control circuits of boost-derived converters. The circuit’s output voltage inherently follows the main regulated output and therefore, does not require an additional active control. The paper presents a detailed analysis of the circuit and offers design guidelines. Following the presentation of the basic idea several variations of the circuit, that can be used in special applications, are presented. The feasibility of the proposed bias circuits was verified by simulation and experiment on a laboratory prototype.

The reduction of PV prices and interest in energy independence accelerate the adoption of residential battery storage. This storage can support various functions of an energy system undergoing decarbonization. In this work, operative benefits of the storage from the system perspective, namely, generation cost reduction and congestion mitigation, are investigated. Germany is chosen as a case study due to its strong reliance on variable renewable energy. For the analysis, an economic dispatch model with a high spatial resolution is coupled with a Pan-European transmission grid model. It is shown that the system's generation costs are highest when the assets are used only to maximize the PV self-consumption, and the costs are lowest when the storage also reacts to the market dynamics. This amounts to 6% cost reduction. Both operation strategies result in an equal level of grid congestion and infrastructure loading. This is improved with a strategy that accounts regional peak reduction as a secondary objective. The high congestion level emphasizes the grid expansion need to keep pace with the generation and electrification expansion necessary to decarbonize other sectors. Lastly, policymakers should enable multipurpose utilization, e.g., via the introduction of market-oriented retail electricity prices with intervention options for grid operators.

The methods of Artificial Intelligence (AI) have been used in the planning and operation of power systems for more than 40 years. In recent years, due to the development of microprocessor and data storage technologies, the effectiveness of this use has greatly increased. This paper provides a systematic overview of the application of AI including the use of Machine Learning (ML) to the power system. The potential application areas are divided into four blocks and the classification matrix has been used for clustering the AI application tasks. Furthermore, the data acquisition methods for setting the parameters of AI and ML algorithms are presented and discussed in a systematic way considering the supervised and unsupervised learning methods. Based on this, three complex application examples: wind power generation forecasting, smart grid security as-sessment (using two methods), and automatic system fault detection are presented and discussed in detail. Summary and outlook conclude the paper.

This paper presents two control design strategies for voltage regulation in a single inductor dual output (SIDO) DC-DC Buck converter system. Based on a nominal multiple input multiple output (MIMO) plant model and performance requirements, both an LQR and a decoupled PI control laws are designed to control the power converter system, under parametric uncertainties such as voltage source variation, CPL power variation, and load resistance variation. Therefore, the SIDO converter can cascade operating, which may cause the undesired effects of voltage oscillation and reduce the system's stability margin. The control performance was assessed under both uncertainties resistive loading and power variation of a constant power load (CPL). A SIDO DC-DC Buck converter board has been developed for experimental tests. The experimental results show that the LQR strategy, compared to the PI strategy, presented a robust performance in the presence of parametric uncertainties in the resistive loads being, however, sensitive to uncertainties due to the presence of CPL loads.

The medium-voltage DC (MVDC) technology has gained increasing interests in recent years. Power electronics devices dominate those grids. Accurate simulation of such a grid, with detailed models of switching semiconductors, can quickly became very time-consuming, according to the number of connected devices to be simulated. A simulation approach based on interactions on a continuous time model can be very interesting, especially for developing a system level control model of such a modern MVDC distribution grid. Aim of this paper is to present all the steps required for obtaining a continuous time modelling of a +/- 10 kV MVDC grid case study, including Solid State Transformer (SST) and Modular Multilevel Converter (MMC) based Active Front End (AFE). Additional aim of this paper is to supply an educational content about the use of the continuous time simulation approach, thanks to a detailed description of the various devices modelled into the presented MVDC grid. The results of a certain number of simulation scenarios are eventually presented.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

As the global transition towards renewable energy accelerates, the integration of grid-scale energy storage systems has become increasingly critical for stabilizing energy supply and enhancing grid reliability. Among various storage technologies, lithium-ion batteries stand out for their high energy density, scalability, and relatively low environmental impact. This study investigates the performance and longevity of lithium-ion batteries in grid-scale applications, focusing on the impact of operational parameters such as cycling frequency, depth of discharge, temperature fluctuations, and charging/discharging rates. Employing a mixed-methods approach, we combined quantitative analysis of performance metrics (cycle life, capacity fade, efficiency) with qualitative assessments from case studies of existing grid-scale projects. Our findings reveal that while lithium-ion batteries exhibit robust performance in grid-scale storage, their longevity and efficiency are significantly influenced by operational conditions. Specifically, temperature management and optimized cycling strategies were identified as key factors in mitigating degradation and extending battery life. This research provides a comprehensive understanding of lithium-ion battery behavior in grid-scale environments, offering valuable insights for the design, optimization, and management of energy storage systems. By addressing the challenges of battery performance and longevity, our study contributes to the development of more sustainable and reliable grid storage solutions, facilitating the broader adoption of renewable energy sources.

In this paper, a continuous power management for a decentralized DC microgrid (DCMG) is proposed to achieve voltage regulation and power balance even under system uncertainty and voltage sensor failure. The DCMG system achieves a continuous power management through only the primary controller to reduce the computational burden of each power agent. To enhance the reliability and resilience of the DCMG system under voltage sensor failure, a DC bus voltage (DCV) sensor fault detection algorithm is proposed. In this algorithm, the DCV sensor failure is detected by comparing the measured DCV with the estimated DCV. When the power agent identifies the DCV sensor failure, it changes the operation properly according to the proposed control mode decision algorithm to maintain the stability of the DCMG system. When uncertain conditions such as the power variation of the distributed generations, sudden grid disconnection, DCV sensor failure, electricity price change, and critical battery status occur, the DCMG system is changed to transitional operation modes. These transitional operation modes are employed to transmit the power agent information to other agents without digital communication links (DCLs) and to accomplish power sharing even under such uncertain conditions. In the transitional operation modes of the DCMG system, the DCV levels are temporarily shifted to an appropriate level, enabling each power agent to detect the uncertainty conditions, and subsequently to determine its operation modes based on the DCV levels. Simulation and experimental results under different test conditions confirm the reliability and effectiveness of the proposed control scheme.

Grid modernization has been ushered in by rising electricity consumption, deteriorating infrastructure, and increasing reliability concerns for electric utilities. New advances, collectively referred to as the smart grid, include modern electronics, technology, telecommunications, and computing capabilities. Smart grid telecommunication frameworks provide two-way communication to support grid operations. Software-defined networking (SDN) has been proposed as a method of monitoring and controlling telecommunication networks, enabling increased smart grid visibility, control, and security. However, being connected to telecommunications infrastructure means that smart grid networks are exposed to cyber-attacks. Attackers may use unauthorized access to intercept messages, inject false data into system measurements, flood communication channels with false data packets, or target centralized controllers to cripple network control. Defense and security techniques against these threats are constantly evolving, necessitating an up-to-date, comprehensive study analyzing cyber attacks and defense methods for smart grid networks. Previous smart grid security surveys do not contain recent techniques and to our knowledge most, if not all, address only one type of attack type and/or one type of defense. This survey considers the latest security techniques, simultaneous multi-pronged cyber attacks and defensutilityes to meet the challenges of the next-generation SDN smart grid research with the goal of identifying future research needs, describing the open security challenges, and exposing both emerging threats and their potential impact on SD-SG deployment.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

This paper provides a study on the development of solar energy, its prospects, and its impacts in Africa. Although the main focus is on technologies adopted for different uses (solar farms, mini-grids, off-grid, solar houses, irrigation, lighting, etc.), we also consider some aspects that increase the adoption of solar energy, such as legislation and business models. Finally, we will examine current and future solar projects managed by NGOs and international companies and how they benefit to leveraging social and economic standards, quality of life as well as capacity building in Africa. This study shows the plethoric interest of institutions outside Africa in the market of solar energy in the continent and that there is no African strategy to increase its independency toward a sustainable development particularly through energy transition.

Very heavy stratiform precipitation (> 200 mm/per day) occurred in the Hokitika region on the west coast of the South Island of New Zealand on 18 June 2015, under north-westerlies with small CAPE (< 25 J/kg). Analyses of model simulations and observations showed that this heavy rainfall was due to cold front lifting enhanced by orographic lifting over the Southern Alps. At 1.5 km grid-length, the model terrain underestimated the average height of the 103 tallest mountains over the South Island by ~ 800 m. This leads to weaker orographic lifting and mountain blocking, and a faster-moving and stronger cold front in the Hokitika region. As a result, large errors in the heavy rainfall prediction occur. By increasing either the resolved or the sub-grid mountain heights, the simulated rainfall errors were largely reduced through stronger orographic lifting and mountain blocking, and a better simulation of the cold front movement and strength. All the experiments have the same “flow-over” regime with mountain waves and/or wave breaking (Fm ranges 0.61 – 1.21). However, the rainfall amount and distribution on the windward side of mountains altered significantly. Our new findings were that the Southern Alps can have significant indirect effects on heavy rainfall by altering the speed and strength of the cold front, in addition to the well-known direct dynamical effects (i.e., orographic lifting and mountain blocking). A combination of these direct and indirect effects makes the heavy rainfall simulation sensitive to mountain heights even under the same “flow-over” regime.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

An off-grid solar energy storage system (ESS) in National Pingtung University of Science and Technology (NPUST) was built and officially operated on Jun. 16th 2022. The system is installed in a 40' general container with PV panels of solar power 8250 W_p on top of the container. The ESS is made by repurposed lithium iron phosphate (LFP) batteries of 20 kWh capacity, where a battery management system (BMS) is adopted to ensured the safety of the battery system. An energy management system (EMS) is built to receive, process, analyse, store, and output the energy information. In this manuscript, a brief engineering report about the system is given.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

The rapid integration of Information and Communication Technology (ICT) is transforming the traditional electrical grid into a {\em Smart Grid}. Smart grids enable two-way communication and improved monitoring and control between utilities and customers. However, due to its heterogeneous nature, public exposure, and weak security at low-powered devices, the Smart Grid has vulnerabilities to various malicious threats, adversaries, and cyber attacks, which may affect cost and service availability. Additionally, when the systems' confidentiality, integrity, or availability are compromised, the resulting fallout can threaten national security and have cascading effects on human lives. Given the extreme consequences of an attack, smart-grid technology must be thoroughly tested for correct operation and security {\em before} it is deployed. As a result, vulnerability testing of smart grids, not only for correctness but for security purposes, has been the subject of numerous studies by academics, government agencies, and private companies. This paper reviews the vulnerabilities associated with the smart grid and spotlights simulation as the vulnerability testing methodology conducted in recent pertinent research works. It also presents various security aspects of the smart grid, including grid applications, system and network infrastructure and components, cyber threats and attacks, simulation, and different mitigation techniques. Finally, we analyze the gaps in the current research works, focusing on simulation. We briefly present a real-time simulation testbed that mimics customer behaviour and integrates hardware in the loop to apply attack methods, analyze vulnerabilities and risk mitigation associated with the smart grid system, and propose future work to improve the current framework.

In a context of increasingly necessary energy transition, precise modelling of profiles for low-voltage (LV) network consumers is crucial to enhance hosting capacity. Typically, load curves for these consumers are estimated through measurement campaigns conducted by Distribution System Operators (DSO) for a representative subset of customers or through the aggregation of load curves from household appliances within a residence. With the instrumentation of smart meters becoming more common, a new approach to modelling profiles for residential customers is proposed to make the most of the measurements from these meters. The disaggregation model estimates the load profile of customers on a low-voltage network by disaggregating the load curve measured at the secondary substation level. By utilizing only the maximum power measured by Linky smart meters, along with the load curve of the secondary substation, this model can estimate the daily profile of customers. For 48 secondary substations in our dataset, the model obtained an average symmetric mean average percentage error (SMAPE) error of 4.91% in reconstructing the load curve of the secondary substation from the curves disaggregated by the model. This methodology can allow the estimation of the daily consumption behaviors of the low-voltage customers. In this way, we can safely envision solutions that enhance the grid hosting capacity.

A three-phase multilevel inverter (MLI) synthesized with 31-levels in the output voltage is used to provide ac supply to a three-phase, squirrel-cage induction motor. The gating angles required for thirty power switches in MLI are optimized by both Genetic Algorithm (GA) and Gray Wolf Op-timization (GWO). In the optimization technique, the optimal angles are determined by solving the trigonometric equations from the Fourier analysis for targeting minimum total harmonic distortion (THD) at the MLI output. Simulation model and experimental prototype are developed for performance analysis and validation. The results obtained demonstrate that the MLI is effec-tively able to produce 31-levels of three-phase ac output voltages with THD not exceeding 5% when loaded with a resistive load and a three-phase induction motor. The voltages and currents are measured and recorded for different loads and operating conditions, including the amount of energy consumed by the loads, as well as frequency analysis, which shows the absence of most of the triple harmonics that have a negative impact on the efficiency of the inverter.

The paper proposes a methodological way to compensate the imbalance between energy generation and consumption using the battery block of electric vehicles as energy reservoir through the well-known Vehicle to Grid system (V2G). The method is based on a simulation process developed by the authors that take into consideration the daily fluctuations of energy consumption as well as the power level generated by an energy source, either conventional, renewable or hybrid. The study shows that for very large electric vehicle fleet the system renders non-viable, since the remaining energy in the battery block to let the electric vehicle usable for running during daytime avoids to compensating for the energy grid imbalance, only allowing to cover a percentage of the energy imbalance, which the proposed methodology may optimize. The analysis of the proposed methodology also shows the viability of the system when being applied to a small fleet of electric vehicles, not only compensating for the energy imbalance but also preserving the required energy in the battery of the electric vehicle to make it run. The method allows predicting the optimum size of electric vehicle battery, which depends on the energy generation level, coverage factor of the energy imbalance and size of the electric vehicle fleet.

A parallel shallow water flow model is introduced in this paper. The explicit-time finite volume approach is adopted to solve the 2D shallow water equations on an unstructured triangular mesh. The proposed scheme is second-order accurate in temporal and spatial terms using the two-stage Runge-Kutta and the monotone upwind scheme for conservation law (MUSCL) methods, respectively. Based on Message Passing Interface (MPI) and OpenACC, a multi-GPU model is presented with the METIS library to produce the domain decomposition. A CUDA-aware MPI library through GPUDirect for peer-to-peer (P2P) transfer between two GPUs and overlapping computation and MPI communication are used to speed up MPI memory exchange and the performance of the code. A 2D circular dam break test with wet and dry downstream beds and grid resolutions of about 2 million cells is considered to verify the accuracy of the code, and good results were achieved compared to the numerical simulations of published studies. Compared with the multi-CPU version of the 6-core CPU, maximum speedups of 56.18 and 331.51 were obtained using the single-GPU and multi-GPU versions, respectively. Results indicate that acceleration performance improves as the mesh resolution increases.

This article reviews recent innovations in piezoelectric actuators, then indicates the future research targets. In the materials, the piezoelectric performances of relaxor-lead titanate (PZN-PT, PMN-PT) single crystals have been improved significantly by an AC electric poling technique. Also new loss characterization techniques facilitate developing high-power density piezoelectrics. The RMS vibration velocity reaches 0.6 m/s in the k₃₁ mode in lead zirconate titanate (PZT) nowadays, which corresponds to power density 30 W/cm³. Pb-free materials are urged due to the recent political regulation on toxic materials. In device designs, the original multilayer actuators (MLA) with Ag/Pd electrode have been switched to the ones with Cu or pure Ag, in order to suppress the heat generation, then to enhance the device power density. Piezoelectric micro-electro-mechanical-systems (MEMS’s) started to utilize the <1 0 0> oriented epitaxial films of rhombohedral PZT compositions, which exhibits enhanced piezoelectric properties. Also for higher-power applications, aero-sol deposition (AD) methods have been introduced to 10 -thick films. Regarding drive/control techniques in piezo-actuators, three developments are on-going, that is, “negative capacitance” power supplies for driving off-resonance (pseudo-DC) piezo-actuators, capacitive AC power supplies for efficiently driving resonance piezo-actuators, and DC/DC converters for harvesting electric energy from high-impedance piezoelectric devices under noise vibration. The applications of piezoelectric actuators in the 21^st century seem to be oriented toward “politico-engineering” with four keywords, “cooperation, protection, reduction, and continuation”. The sustainability technologies include the following piezoelectric items: (a) Pb-free piezoelectrics, (b) ultrasonic technology for decomposing hazardous materials, (c) reduction of contamination gas, (d) piezoelectric energy harvesting, and (e) device improvement with high energy-efficiency. On the other hand, the following crisis technologies have been developed with piezoelectrics: (a) detection and neutralization technologies of infectious/epidemic diseases such as anthrax, (b) autonomous unmanned underwater, aerial, and land vehicles with piezoelectric actuators, (c) pin-point target weapons, (d) high voltage supplies with piezoelectric transformers, and (e) compact energy sources for remote actuating/sensing systems.

Simultaneous Localization and Mapping (SLAM), as one of the core technologies in intelligent robotics, has gained substantial attention in recent years. Addressing the limitations of SLAM systems in dynamic environments, this research proposes a system specifically designed for plant factory transportation environments, named GY-SLAM. GY-SLAM incorporates a lightweight target detection network GY based on YOLOv5, which utilizes GhostNet as the backbone network. This integration is further enhanced with CoordConv coordinate convolution, CARAFE up-sampling operators, and SE attention mechanism, leading to simultaneous improvements in detection accuracy and model complexity reduction. While improving mAP@0.5 by 0.514%, the model simultaneously reduces the number of parameters by 43.976%, computational cost by 46.488%, and model size by 41.752%. Additionally, the system constructs pure static octree maps and grid maps. Tests conducted on the TUM dataset and a proprietary dataset demonstrate that GY-SLAM significantly outperforms ORB-SLAM3 in dynamic scenarios in terms of system local-ization accuracy and robustness. It shows a remarkable 92.58% improvement in RMSE for Absolute Trajectory Error (ATE). Compared to YOLOv5s, the GY model brings a 41.5944% improvement in detection speed and a 17.7975% increase in SLAM operation speed to the system, indicating strong competitiveness and real-time capabilities. These results validate the effectiveness of GY-SLAM in dynamic environments and provide substantial support for the automation of logistics tasks by robots in specific contexts.

In this study, the unsteady Reynolds-averaged Navier-Stokes (URANS) equations are employed in conjunction with the Menter Shear Stress Transport (SST)-Scale-Adaptive Simulation (SAS) turbulence model in compressible flow, unstructured mesh and complex geometry. Whereas, other scale-resolving approaches in space and time, such as Direct Numerical Simulation (DNS) and Large-Eddy Simulation (LES), supply more comprehensive information about the turbulent energy spectra of the fluctuating component of the flow; however, previously mentioned avenues imply computationally intensive situations, usually performed over structured meshes and relatively simply geometries. In contrast, the SAS approach is designed according to “physically” prescribed length scales of the flow. More precisely, it operates by locally comparing the length scale of the modelled turbulence to the von Karman length scale (which is prescribed according to local fluid velocity derivatives and depends on the grid point distribution in the computational domain). This length scale ratio allows the flow to dynamically adjust the local eddy viscosity in order to better capture the large scale motions (LSM) in unsteady regions of URANS simulations. While SAS may be constrained to model only low flow frequencies or waivenumbers (i.e., LSM), its versatility and computational low-cost make it attractive to obtain a quick first insight of the flow physics; particularly, in those situations dominated by strong flow unsteadiness. The selected numerical application is the well-known M219 three-dimensional rectangular acoustic cavity from the literature at two different freestream Mach numbers, M∞ (0.85 and 1.35) and a length-to-depth ratio of 5:1. Thus, we consider the “deep configuration" in experiments by Henshaw. The SST-SAS model has demonstrated a satisfactory compromise between simplicity, accuracy and flow physics description.

Power grid fault diagnosis technology has been widely used at home and abroad. With the access of distributed power sources and diversified loads, the distribution network has changed from a passive network to an active network, and the current has changed from "one-way" to "two-way". The structure of distribution network, equipment environment and operating conditions are becoming more and more complex, and the fault diagnosis and localization of active distribution network is becoming more and more difficult. With the rapid development of artificial intelligence, power grid fault diagnosis based on intelligence is unprecedented. This paper introduces the research status of distributed photovoltaic grid-connected fault diagnosis technology, and expounds the history of fault diagnosis technology, which mainly includes expert system, artificial neural network, Bayesian network, fuzzy set theory, rough set theory, Petri net analytical model and multi-source information fusion, etc. The applicability and characteristics of these diagnoses are described, and the existing defects and the overall direction of improvement are briefly described Finally, the key technical problems and future directions in the field of power system fault diagnosis are pointed out by combining theory with practice, so as to promote the further development of this field.

In many developing countries of the world including Pakistan motorcycle steeling is one of the main issue that needs to be dealt with an iron hand as it leads to economic losses as well as crime increase in the society, according to the DOWN REPORT there were 28609 motorcycle stolen in 2019 and this number has been increased to 34908 in 2020. Now due to the increasing motorcycles stealing crime what measures can we take to reduce the number of motorcycle theft the rule of technology is enormous in this regards specially information technology (IT) , information technology can play an important role in the security of motorcycles from being theft by the thieves, Information technology provide us the GSM based control system which can be very help full to construct a security system for motorcycle in order to make it antitheft.

The coupling of AC and DC power will impact the protective actions on the AC side and pose a threat to the stable operation of the interconnection system. Therefore, a new longitudinal protection method is proposed based on the comprehensive distance similarity of voltage waveforms. Initially, the measured voltage and current data are extracted to calculate the reference voltage, and the voltage waveform fitting is optimized. Subsequently, the Euclidean dynamic time warp (DTW) distance and entropy weight method are utilized to process the voltage waveform, enabling the calculation of its comprehensive distance similarity. This similarity is adopted to determine fault location. A hybrid DC multi-feed AC/DC interconnection system, incorporating line commutated converter-voltage source converter (LCC-VSC) and line commutated converter-modular multilevel converter (LCC-MMC), was established in PSCAD, and fault data was simulated and output. The effectiveness of the protection scheme was validated using MATLAB. Simulation results demonstrate that the proposed method can accurately distinguish between faults inside and outside a region. When compared to existing protection methods, it demonstrates superior performance in resisting transition resistance and noise interference, while also mitigating the impact of data asynchronicity. The speed and reliability of the method are further enhanced.

A robust explicit model predictive control (EMPC)-based frequency adaptive grid voltage sensorless control is developed for a grid-connected inverter (GCI) via a linear matrix inequality (LMI) approach under the model parameter uncertainties and non-ideal grid environment. The control scheme is achieved by an enhanced prediction model rather than the conventional prediction model provided by fixed parameters to maintain the quality of grid currents injected into the grid when the model parameters are varied. Furthermore, an LMI-based observer is integrated with the disturbance observer to improve the reference tracking performance and reject disturbances. The proposed observer is employed for the grid frequency adaptive control without need of grid voltage sensors. The proposed current controller and observer employ the LMI scheme to maintain a stable and robust operation of the GCI. The discrete-time frequency response and pole-zero map analyses are used to investigate system stability and robustness against parameter uncertainties. Comprehensive simulation, experimental results and analyses clearly demonstrate the robustness of the proposed control scheme under various adverse test conditions with unexpected grid and system uncertainties.

Energy management systems (EMS) play a central role in improving the performance of microgrids by ensuring their efficient operation while minimizing operational costs and environmental impacts. This paper presents a comprehensive study of a MILP-based EMS developed and implemented in MATLAB using Yalmip software for the energy management of a new positive energy district in the city of Savona, Italy, as part of the Interreg Alpine Space Project ALPGRIDS. The main objective of this research is to optimize the functioning of the microgrid, focusing on cost efficiency and environmental sustainability. In pursuit of this objective, the EMS undergoes comprehensive testing and analysis, replicating actual conditions and addressing the diverse demands of end-users across typical days throughout the year considering real electricity selling and purchase price. The EMS also accounts for the reactive power capabilities of the various technologies integrated into the microgrid. The levelized cost of electricity (LCOE) serves as a metric for assessing curtailment costs, while penalties related to reactive power absorption from the distribution network are appraised in alignment with prevailing regulatory guidelines. The case study provides valuable insights into the practical implementation of EMS technology in microgrids and demonstrates its potential for sustainable energy management in complex urban energy districts. The insights and strategies developed through this research contribute to the overall goals of improving energy efficiency and reducing the environmental footprint of future energy districts.

This policy paper explores various strategies that would facilitate transitioning the traditional Jordanian electrical grid to a secure smart grid. It includes comprehensive recommendations from academia and industry for the regulatory and governmental sector in Jordan to achieve specific roadmap objectives. As Jordan is heavily dependent on fossil fuels, This policy paper also provides recommendations for incorporating more renewables into its energy mix, thereby facilitating a sustainable future. The proposed policies will emphasise the creation of an enabling environment where innovation, research, and development initiatives flourish, thereby promoting private sector engagement.

Solid-state transformer (SST) is a promising technology for smart grids due to its flexible power control (better reliability) and high efficacy (by decreasing losses) compared with traditional transformers. The SST is designed in tandem with three stages, i.e., the input, isolation, and output stages. As three converter stages are used to design the SST to make a more reliable device in practice, it is highly prone to instabilities. Moreover, the key objective of SST design is to implement a modern power distribution system to make it more intelligent and reliable. The stability issue can be even more complicated by the presence of distributed energy resources in the distribution system. Thus, the stability of SST must be measured prior to /during the design, and to determine, a state-space model is used, which is developed in this paper. Each stage of SST is modeled with its controller, and the system's stability is measured through the controllability and observability test. Further, the conversion from state-space to transfer function model is done, and the stability of SST is shown using frequency and time-domain diagrams. With these, the different plots, namely, the Bode plot, Nyquist plot, Nichols chart, Root locus, pole-zero plot, and Eigen plot, are used to ascertain the relative and absolute stability. Finally, the SST Simulink model is tested and validated through hardwate-in-the-loop simulation, i.e., OPALRT, to show its effectiveness and applicability.

The three-axis stabilization geostationary remote sensing satellite features high time resolution and plays a significant role in weather forecasting and environmental monitoring. With the future development of satellite technology, we propose a rapid geolocation algorithm for three-axis stabilization geostationary remote sensing satellites from the perspective of software algorithms. The method assesses conventional remote sensing data geolocation methods and the coordination group for meteorological satellites (CGMS, Coordination Group for Meteorological Satellites) nominal grid publishing format. First, the initial incident viewing vector of each detector on the sensor was constructed. Then, by reflecting the satellite platform's east-west and north-south mirrors, the outgoing vector of the payload coordinate system was obtained. This vector was converted to the satellite body coordinate system and, subsequently, to the satellite orbit coordinate system. The conversion of the earth-fixed coordinate system and the mirror rotation angle under ideal CGMS grid conditions were obtained, and the mirror rotation angle was converted to the corresponding CGMS nominal grid position to complete data positioning. The algorithm omits the complex process of calculating the intersection point between the viewing vector and the geodetic ellipsoid sphere from the earth-fixed coordinate system, resulting in an 83.3% improvement in computational efficiency without compromising positioning accuracy compared with conventional geolocation methods. This algorithm greatly improves the processing efficiency of geostationary meteorological satellite positioning, but its limitation is that the data processing results must be released in the CGMS nominal grid format.

With the increasing prominence of renewable energy sources providing flexibility to the power grid, there is a growing recognition of the need to expand virtual Energy Storage Systems (ESS) to replace traditional ESS, which faces challenges in terms of supply and scalability. Grid-connected microgrids can supply power stably and are being built, so they can be used as virtual ESS to provide flexibility to the power system. This study proposes an approach to determine the optimal Power Conversion System (PCS) and battery capacity for a Virtual Energy Storage System(VEES) based on a grid-connected microgrid incorporating Photovoltaic (PV) and ESS. In this paper, it is assumed that microgrids can provide flexibility to the grid by participating in the energy trading market, there are corresponding profits and penalties for order. Numerical examples are performed to demonstrate the effectiveness of the proposed method.

In this paper, a buck DC-DC converter with the proposed twin frequency control scheme (TFCS) and accurate load current sensing (ALCS) have been designed and implemented with 0.18µm CMOS technology for a supply voltage ranging from 2.0-3.0V which is compatible with state-of-the-art batteries (NiCd/NiMH: 1.1-2V, Li-Ion: 2.5-4.2V). The proposed converter yields a peak efficiency of about 92.7% with a load current of 30mA. Furthermore, it only occupies a silicon area of 1.3mm2. The proposed buck converter is dedicated for smartphone applications whereby it spends most of its time in idle, low load conditions.

This paper presents the mathematical modeling for designing a 10[kW] DC-AC inverter system from 48 [V] DC to 120 V ACrms, considering its non-linear operation, allowing to obtain a detailed simulation to assess the proposed fuzzy PI control (with anti-windup action) and its optimal operation. The performance assessment of the converter was carried out with the discrete treatment of the voltage and current signals using spectral analysis, filtering considerations, and evaluation of limit cycle technique to determine the system's stability. The main results showed that THD at the filter output (transformer and capacitor) was around 0.0322% and 0.0632% at nominal load in open loop and closed loop, respectively. The inverter system presented more sensitivity in the current signal with a ripple at 120 [Hz] of 2.02% and at 5000 [Hz] of 10.62% (at nominal load). However, when the system operates in a closed loop, the current ripple at 120 [Hz] is 2.38% and at 5000 [Hz] is 10.62%.

It is a critical issue to allocate redundancy to critical smart grid infrastructure for disaster recovery planning. In this study, we present a framework to combine statistical prediction methods and optimization models for the optimal redundancy allocation problem. First, we develop statistical simulation methods to identify critical nodes of very large-scale smart grid infrastructure based on the topological features of embedding networks, and then present a linear integer programming model based on generalized assignment problem (GAP) for redundancy allocation of critical nodes in smart grid infrastructure. The model is specifically implemented in the context of smart grid infrastructure. The findings demonstrate that the combined approach of statistical simulation and optimization effectively addresses the size limitations inherent in a sole optimization approach. Notably, the optimal solutions for redundancy allocation in very large grid systems highlight that the cost of redundancy is only a fraction of the economic losses incurred due to weather-related outages.

This paper proposes a circuit model of Cross-Coupled CMOS AC – DC Charge Pump (XC – CP) operating in subthreshold region. The aim is improving the efficiency to design XC – CPs with variety of specifications, e.g., input and output voltages and AC input frequency. First, it is shown that the output resistance (Ro) of XC – CP is much higher than those of CPs with single diodes (SD – CP) and ultra-low-power diodes (ULPD – CP) as charge transfer switches (CTSs). Second, the reason behind the above feature of XC – CP is identified by a simple model that the gate-to-source voltages of CTS MOSFETs are independent of the output voltage of the CP. Third, high but finite Ro of XC – CP is explainable with a more accurate model that includes the dependence of the saturation current of MOSFETs operating in subthreshold region on the drain-to-source voltage which is a function of the output voltage of CP. The model was in good agreement with measured and simulated results of XC – , SD – and ULPD – CPs fabricated in 250 nm CMOS.

To ensure sustainability of the future power grid, the rate of expansion of distributed renewable energy resources (DRER) has introduced operational challenges. These includes managing transmission constraints with DRER power injection, dispatching DRER efficiently, managing system frequency and ensuring sufficient reactive power for voltage support. Coupled with the intensification of wildfires, power infrastructure across the United States faces challenges to minimize the impact to maintain system reliability and resiliency. This research embarks on a comprehensive evaluation, beginning with an in-depth historical analysis to delineate regions most susceptible to wildfires. Utilizing a multidimensional approach, the study assesses wildfire-induced risks to power grids, by integrating historical wildfire occurrences, real-time wildfire proximities, Moderate Resolution Imaging Spectroradiometer (MODIS) derived vegetation metrics, and system parameters, by employing Principal Component Analysis (PCA) based optimal weights, leading to the formulation of a novel risk factor model. This risk factor has the potential to be the key to ensuring the resilience of a renewable-rich smart grid when faced with a severe weather event. Our model’s applicability was further verified through an empirical assessment, selecting representative networks from diverse regions, providing insights into the geographical variability of risk factors. Ultimately, this study offers stakeholders and policymakers a comprehensive tool-set, empowering decisions regarding infrastructure investments, grid reinforcements, and strategic power rerouting to ensure consistent energy delivery using risk assessment against wildfire.

This research article aims to present implementation and evaluation of the HPPT design based on using multi-parallel pumps switching for yielding performance with reference to potential change of daily irradiance. After that, the curve fitting of the hydraulic performance scenarios is tested to compare the hydraulic energy growth behaviors with reference to exponential and power growth models.

The power generation structure and load characteristics in different provinces are quite different in China, and the distribution of peak regulating resources and demands is extremely unbalanced. Due to many factors such as low power marketization degree, shortage of peak regulating resources and block of transmission channels, the consumption of new energy is facing greater pressure. In order to improve the mutual aids in regional power grid, this paper proposes a two-layer optimization dispatching model considering the mutual aids of peak regulation resources between each province, and determines the optimal units startup mode and power output in each provinces, thus obtaining all the power supply output arrangements and the technical and economic indicators. Finally, take the actual regional power grid in China as an example, the simulation results show that the proposed model can significantly improve the new energy utilization rate, which verified the effectiveness and feasibility of the proposed model and methods in this paper.

To achieve a fast testing on barrier properties of organic coatings, immersion test, AC-DC-AC test, and coupled test of AC-DC-AC with hydrostatic pressure were conducted in seawater for a glass flake epoxy coating. Electrochemical impedance spectroscopy (EIS) was used to characterize the degradation processes of the coating during the tests, and the surface of the coating was analyzed using optical microscope, scanning electron microscope (SEM) and Fourier transform infrared spectrometer (FTIR). The results show that the periodically cathodic polarization coupled with high hydrostatic pressure can accelerate the degradation of the coating by facilitating the diffusion and uptake of electrolyte and the delamination of the coating. The coupled test method has the largest acceleration due to the synergetic effect of AC-DC-AC and hydrostatic pressure.

Continuous greenhouse gas emissions are causing global warming and impacting the habitats of many animals. Researchers in the field of electric power are making efforts to mitigate this situation. Operating and maintaining the power grid in an economic, low-carbon, and stable is challenging. To address the issue, we propose a grid dispatching technique that combines prediction technology, reinforcement learning, and optimization technology. Prediction technology can forecast future power demand and solar power generation, while reinforcement learning and optimization technology can make charging and discharging decisions for energy storage devices based on current and future grid conditions. In the power system, the aggregation of distributed energy resources increases uncertainty, particularly due to the fluctuating generation of renewable energy. This requires the use of advanced predictive control techniques to ensure long-term economic and decarbonization goals. In this paper, we present a real-time dispatching framework that integrates deep learning-based prediction, reinforcement learning-based decision-making, and stochastic optimization techniques. The framework can rapidly adapt to target uncertainty caused by various factors in real-time data distribution and control processes. The proposed framework achieved global Champion in the NeurIPS Challenge 2022 competition and demonstrated its effectiveness in practical scenarios of intelligent building energy management.

Smart grid capabilities have grown significantly in recent years. The smart grid provides advanced real-time handling of faults, advanced automatic control for efficient electricity transmission, monitoring and collection of the electrical system's capacity, and communication for information sharing. Unfortunately, its exposure to public networks makes it increasingly vulnerable to privacy breaches, vulnerabilities, and cyber-attacks. Cyber security threats and vulnerabilities in smart grid networks have become a primary concern that needs to be addressed before deploying a smart grid. Furthermore, the wide range of protocols increases the attack surface of a smart grid. This study focuses on the vulnerability of Modbus, which is regarded as one of the most prevalent protocols in smart grid communication networks. This paper presents preliminary findings of analyzing cyber-attacks against the Modbus protocol using a virtual testbed to investigate its effects on the smart grid network protocol. The concept incorporates an emulated Modbus/TCP network environment built from open-source software components that imitate fundamental industrial control features of the smart grid. Finally, we analyze the cycle of a cyber-attack leading through Reconnaissance to a DoS attack on the Modbus/TCP protocol and propose improvements to the test bed for protocol attack detection and mitigation.

Besides the increase in global energy demand, access to clean energy, reduction in greenhouse gas emissions caused by conventional power generation sources, energy security, and availability of electricity in remote villages in emerging nations are some of the factors that foster the use of renewable energy sources (RESs) in generating electricity. One of the aims of initiating microgrids (MGs) is to maximize the benefits of RES and alleviate the associated grid integration issues. Microgrids are made up of RES connected to electrical loads within clearly delineated electrical limits that operate as individual controllable units on the electrical network. It can operate in-dependently as well as in connection with the grid. The paper presents an overview of microgrids and investigates the system's performance when connected to and disconnected from the grid. Furthermore, in both modes of operation, the functioning and behavior of system components such as the bidirectional DC-DC converter and energy storage system (ESS) were evaluated. The architecture of the proposed microgrid consists of a small hydropower plant, a wind farm, and a battery energy storage system (BESS). The microgrid under investigation is modeled and simu-lated using MATLAB and Simulink.

Transportation electrification has been identified as a crucial shift to be made for achieving energy security and emission reduction targets. Electric Vehicles (EVs) play a significant role in achieving these targets; therefore, there is a growing trend to develop new EV technologies and associated infrastructure. Along with these developments, EVs' Quality of Service (QoS) aspects should be enhanced to increase the number of EVs on the road. Various QoS factors are defined to assess the QoS of EVs, and one of the two aims of this paper is to provide a comprehensive review of these factors. The other aim is to review recent developments of associated communication technologies which are essential for exchanging information between EVs and charging stations. This paper serves as a comprehensive review and useful reference for researchers working on QoS aspects of EVs and associated communication systems aiming to enhance the QoS.

The smart grid system, an improvised form of the traditional grid, is considered a critical cyber-physical system. Due to its complex combination of smart and legacy technologies, this technology is characterized by a wide range of features such as full duplex communication, advanced metering infrastructure, remote monitoring, and control. However, despite this system’s substantial environmental and socio-economic impact on modern life, it poses severe security vulnerabilities due to its integration and interconnected and interdependent cyber-physical components. Based on the rapid development of cyber-physical systems (CPS), academics and industries have investigated relevant techniques to enhance and strengthen the security measures of the SG system. The intrusion detection system is a countermeasure, a powerful safeguard against various cyber-attacks and threats. The contribution of the IDSs to the SG paradigm is examined in this study. A comprehensive review has been presented in this study, highlighting different techniques, basic ideas, and analyses. Besides discussing the contemporary pertinent research studies, the shortcomings of the existing IDS for the SG system are also identified with a recommendation for future research direction.

This paper provides a new management method (MM) to optimally operate standalone direct current (DC) photovoltaic water pumping system (PVWPS) and synchronize its hydraulic performance to variable daily irradiance. The proposed approach well considers the issues from PV generator and a positive displacement pump mismatching to deserve a hydraulic network. Accordingly, Management Method uses small pumps mounted in parallel scheme to displace the hydraulic power point (HPP) in order to satisfy the mal adequacy between supply and load. Based on experimental Study; this approach showed a yielded standalone system, possibility of running pumping system using only photovoltaic supply (Without use of capacitance), and possibility to design more economical PV systems as the maximum peak power demand for each month can be satisfied using small power pumps in parallel and adjusting their switch with accordance to varying daily irradiance. Moreover, an analytical model was developed with reference to the obtained experimental results. This model based on a daily occurring irradiance as inputs in order to predict optimal performance outputs. It can be considered as a decision tool to track power point resulting from optimal electrical and hydraulic performances of the pumping system according to changes of the daily irradiance.

This article presents a comprehensive study on enhancing grid resilience through advanced forecasting and optimization techniques in the context of power outages. Power outages pose significant challenges to modern societies, affecting various sectors such as industries, households, and critical infrastructures. The research combines statistical analysis, machine learning algorithms, and optimization methods to address this issue to develop a holistic approach for predicting and mitigating power outage events. The proposed methodology involves the use of Monte Carlo simulations in MATLAB for future outage prediction, Long Short-Term Memory (LSTM) networks for forecasting solar irradiance and load profiles, and a hybrid LSTM-Particle Swarm Optimization (PSO) model to improve accuracy. Furthermore, the role of Battery State of Charge (SoC) in enhancing system resilience is explored. The study also assesses the techno-economic advantages of a grid-tied microgrid integrated with solar panels and batteries over conventional grid systems. The results highlight the potential of the proposed approach in strengthening grid resilience, reducing downtime, and fostering sustainable energy utilization.

Τhe building automation control is a crucial factor for improving buildings energy efficiency and management, as well as improving the electricity grid's reliability indices. This paper presents the methodology, describes the necessary technology requirements and presents the decentralized building automation novel algorithm for Efficient demand side management in a building. All these are applied in an experimental university microgrid and the results are presented in terms of energy saving in kWh, money in € and working hours.

This paper is concerned with developing an efficient numerical algorithm for fast implementation of the sparse grid method for computing the $d$-dimensional integral of a given function. The new algorithm, called the MDI-SG ({\em multilevel dimension iteration sparse grid}) method, implements the sparse grid method based on a dimension iteration/reduction procedure, it does not need to store the integration points, nor does it compute the function values independently at each integration point, instead, it reuses the computation for function evaluations as much as possible by performing the function evaluations at all integration points in a cluster and iteratively along coordinate directions. It is shown numerically that the computational complexity (in terms of CPU time) of the proposed MDI-SG method is of polynomial order $O(Nd^3 )$ or better, compared to the exponential order $O(N(\log N)^{d-1})$ for the standard sparse grid method, where $N$ denotes the maximum number of integration points in each coordinate direction. As a result, the proposed MDI-SG method effectively circumvents the curse of dimensionality suffered by the standard sparse grid method for high-dimensional numerical integration.

This study investigates the nonlinearities in three-phase inverters for SiC-based systems and compares their performance to IGBT-based systems. An analytical model of inverter voltage distortion is developed, which accounts not only for dead time (td), switching delay time, switching frequency (fs), and voltage drops of power devices, but also for output parasitic capacitance (Cout). Experimental tests validate the model, which provides a more accurate estimate of the inverter’s output phase voltage distortion. The power device characteristics are obtained from datasheets, while Cout is determined through experimentation. Three-phase inverters with varying switching frequencies, fundamental frequencies, and dead-time values are used in simulations and experiments to determine the influence of nonlinearity on phase voltage deviation and current distortion. The results show that, due to SiC devices’ faster switching time, the phase voltage deviation and phase current distortion are lower in SiC-based inverters than in IGBT-based ones for high-frequency applications, as the dead time can be reduced.

This paper introduces a novel algorithm for solving the point-to-point shortest path problem in a static regular 8-neighbor connectivity (G8) grid. This algorithm can be seen as a generalization of Hadlock algorithm to G8 grids, and is shown to be theoretically equivalent to the relaxed A* (RA*) algorithm in terms of the provided solution's path length, but with substantial time and memory savings, due to a completely different computation strategy, based on defining a set of lookup matrices. Through an experimental study on grid maps of various types and sizes (1290 runs on 43 maps), it is proven to be 2.25 times faster than RA* and 17 times faster than the original A*, in average. Moreover, it is more memory-efficient, since it does not need to store a G score matrix.

This paper proposes a novel symmetrical active-switched coupled-inductor high-step-up DC/DC converter. A new active-switched coupled inductor is used to allow much higher voltage gain of the proposed converter. The symmetrical circuit structure of the proposed converter evenly divides large input currents and reduce input current ripple by operating in interleaved mode so power density is increased. The switches also have low voltage stress. The operating principle and design considerations for the converter topology are described. The proposed converter with an input voltage of 40 V, an output voltage of 400 V and an output of 1000 W at a switching frequency of 50 kHz is implemented. The simulations and experimental results are thus depicted to verify the theoretical analysis. The highest efficiency is 95.5% at 200 W measured by using a HIOKI 3390. Consequently, the proposed converter is suitable for renewable energy generation systems that require high power, high voltage gain and high efficiency.

This paper considers the problem of predicting earthquakes. It uses a small amount of information to create a descriptive key that can be used as a footprint to describe an event. A frequency grid clusters events that occurred at the same time and then the algorithm averages the history of these events over preceding days, in particular the gaps when the events did not occur. The gaps are measured for the clustered events only and can be used to create a description that is quite unique. Results suggest that seismic events can in fact be traced using this key and subsequently recognised again, if the same conditions reoccur. They also suggest that force direction may be more important than magnitude, after the initial cluster selections are made. Greek and USA datasets have been looked at and the prediction accuracy can be 70% or better. The author therefore suggests that this is an interesting method that deserves attention.

Stray currents can cause very rapid degradation and material loss at the points where the current leaves the metal and enters the electrolyte. Nowadays, many resources are invested in the protection of jeopardized structures, such as buried pipelines, from stray current corrosion. This paper describes the measures that need to be considered in the design and construction of track structures to ensure high rail-to-ground resistance and consequently reduce stray currents. The main conclusions from existing guidelines and standards for reducing and controlling stray currents that are applied by various track operators are presented in the paper. Rail-to-ground resistance in different types of tracks structures and rail fastening systems is analysed and optimal type of the track and type of the fastening system is defined. The grounding schemes used on the tracks and their influence on stray current values are described, as well as the influence of traction power substation and rail cross bonding on stray current. Since it is not necessary to apply all the measures described to the same track structure, the paper gives recommendations on which measures to apply when building tracks with continuously fastened rails and which to apply when building tracks with discretely supported and fastened rails.

To address the challenges of climate change and food security, the establishment of smart farm complexes is necessary. While there have been numerous studies on the productivity and environmental control of individual greenhouses, research on greenhouse complexes is considerably limited. Conducting environmental studies during the design phase of these complexes poses financial constraints and practical limitations in terms of on-site experiments. To identify potential issues that may arise when developing large-scale greenhouse complexes, it is possible to utilize modeling techniques using Computational Fluid Dynamics (CFD) to assess environmental concerns and location issues before constructing the facilities. Consequently, simulating large-scale CFD models that incorporate multiple greenhouses and atmospheric conditions simultaneously presents significant numerical challenges. The objective of this study was to develop a guideline for verifying CFD models for a large-scale Venlo greenhouse, where acquiring field data before construction is not feasible for designing a greenhouse complex. The verification processes of the CFD models were conducted using 2D and 3D iterative simulations of a 2-hectare greenhouse model, using the improved Grid Independence Test (GIT) and wall Y+ approaches. Subsequently, the aerodynamic characteristics were analyzed in a 3D greenhouse model to access its performance when the wind direction was 90° in summer season. The findings revealed that a grid resolution of 0.8 meters and a first layer height of 0.04 meters were suitable for developing large-scale greenhouse models, resulting in a low Root Mean Square Error (RMSE) of 3.9% and a high coefficient of determination (R2) of 0.968. This process led to a significant reduction of 38% in the number of grid cells. These results will serve as design standards for large-scale greenhouses.

Life in the modern century is heavily reliant on an enormous amount of electricity consumption as technology has become the most integral part of daily life. In this context, smart grid systems play a pivotal role to maintain the uninterrupted power supply which needs to be monitored in a timely fashion to keep track of the electric consumers’ usage pattern. The smart meter is the one of smart applications of the smart grid that collects huge amounts of consumer load data on a daily basis which has become a focus for various researchers and analyzers to study load characterization. In this paper, an approach has been proposed to recognize the energy consumption patterns among diverse types of consumers ranging from residential to industrial levels. This approach is worth considering not only for load pattern recognition but also for involving customers in different events such as demand response or peak shaving. In such a way, this analytical mechanism certainly assists in reducing power wastage and saving costs. The proposed methodology is based on a two-fold clustering algorithm with the use of state-of-the-art technology, machine learning. The primary goal is to classify electric customers' data collected from smart meters. Then, analyzing the classified results with an aim to predict power consumption patterns for the customers in the future and making the right energy policy that will benefit both the grid operator and consumers as well.

This paper examines some of the largely neglected areas of opportunity to utilize skeletal space structure systems in support of modular, industrialized, economical, sustainable and digital future of the construction industry. In this context, the feasibility of future use of skeletal space structures is studied for a few classes of engineering structures, namely, residential apartment buildings, and offshore platforms, along with their suitability for reconstruction, renovation, modernization and retrofit of damaged buildings and urban areas of cultural heritage significance. Finally, the particulars of lean project management of space structures are discussed with emphasis on engineering and economic factors, production management, environmental aspects, quality management, and reliability, maintainability and sustainability considerations. This article concludes that skeletal space structures can fulfil many of the essential construction requirements of modern societies, especially those facing environmental challenges, all while allowing for design flexibility and mass customization.

Modern power system integrates more and more new energy and use a large number of power electronic equipment. This makes it face more challenges in online optimization and real-time control. Deep reinforcement learning(DRL) has the ability of processing big data and high-dimensional features, as well as the ability of independently learning and optimizing decision-making in complex environments. In this paper, we explore DRL based online combination optimization method of grid section for large complex power system. In our method, to improve the convergence speed of the model, we propose to discretize the output action of the unit and simplify the action space. We also design a reinforcement learning loss function with strong constraints to further improve the convergence speed of the model and facilitate the algorithm to obtain the stable solution. Moreover, to avoid the local optimal solution problem caused by the discretization of the output action, we propose to use the annealing optimization algorithm to make the granularity of the unit output finer. We verify our method on IEEE 118-bus system. The experimental results show that our model has fast convergence speed and better performance, and can obtain stable solutions.

Developing a low-cost wireless energy meter with power quality measurement for smart grid applications represents a significant advancement in efficient and accurate electrical energy monitoring.In increasingly complex and interconnected electrical systems, this device is essential in various applications, such as smart grids, enabling real-time energy usage monitoring. In such a context, smart meters expand the possibilities for sustainable and efficient energy use and promote better utilization of energy sources, especially non-renewable ones. According to the 2020 International Energy Agency (IEA) research, non-renewable energy sources represent 65% of the global total. The smart meter developed in this work is built based on the ESP32 microcontroller and easily accessible components, using a user-friendly development platform that offers a cost-effective solution while ensuring reliable performance. The main objective of the smart meter development was to enhance the software and simplify the hardware. Unlike traditional meters that perform electrical parameter calculations using complex hardware circuits, this project performed the calculations directly on the microcontroller. This approach reduced the complexity of the hardware, simplifying the meter’s design. With the high-performance processing capability of the microcontroller, efficient and accurate calculations of electrical parameters were achieved without the need for additional circuits. This software-driven approach with simplified hardware brought benefits such as reduced production costs, lower energy consumption, and increased meter development and updates flexibility. Furthermore, the integrated wireless connectivity in the microcontroller enables the transmission of collected data to remote monitoring systems for later analysis. The developed smart meter offers cost, energy efficiency, and flexibility benefits. It represents an innovative, efficient, and versatile solution for smart grid applications.

Regenerative braking energy (RBE) recovery of trains can improve energy efficiency as well as reduce the overall greenhouse gases emissions of electric rail systems. The train's speed limit, track elevation, track curvature, and headway time can affect the amount of RBE recovered. This study aims to investigate the impacts of these parameters on the RBE recovery for a DC third rail system. A DC third rail system has been modeled using the ETAP-eTraX software based on the Malaysia Mass Rapid Transit Line 2 (MRT Line 2) traction power system. The effects of the change of speed limit, track elevation, track curvature, and headway time of the trains on the RBE recovery have been evaluated under various scenarios. The results showed that the track’s elevation has the most significant influence on the overall energy consumptions of the train while the speed limit has the most significant influence on the amount of RBE recovery.

Microgrid is one of the important ways to accommodate distributed PV generation. However, the optimal planning scheme of microgrids is closely related to solar resources, load characteristics, and the key components of microgrid systems. This paper uses HOMER software to conduct collaborative planning for grid-connected PV-storage microgrids with electric vehicles in multiple scenarios. Specifically, we construct a multi-scenario capacity optimization model for PV generation, energy storage, and converters, considering both the cleanliness and economic performance of microgrids. The performance is quantified using indices such as net present cost, levelized cost of electricity, and carbon dioxide emission under multiple scenarios. Finally, we conduct extensive case studies on a business park in Wuhan, China, to compare and discuss the planning performance under multiple scenarios, as well as sensitivity analysis with specific cases.

The optimization of the energy grid is a critical task for ensuring a sustainable and efficient energy future. Deep machine learning techniques have the potential to improve energy grid optimization by predicting energy demands and supplies, optimizing energy production and distribution, and detecting and preventing fraud. However, there are also several challenges associated with the use of deep machine learning in energy grid optimization. These include the lack of standardized datasets and data quality issues, interpretability and explain-ability of machine learning models, ethical and social implications of using machine learning, and integration with existing energy infrastructure and regulatory frameworks. Having a clear understanding that continued research and developments in deep learning applications to energy field are crucial for achieving a sustainable and efficient energy future. This paper therefore reviewed existing literature for challenges and opportunities associated with deep machine learning in energy grid optimization; and highlights the importance of continued research and development in the field. The paper found out that opportunities for future research in deep machine learning for energy grid optimization include advancements in machine learning algorithms and techniques, development of new datasets and data collection methods, integration of machine learning with other emerging technologies. It also established needs for collaborative research and public-private partnerships.

The present study describes the development and application of a computer model of the national electricity system for the Caribbean dual-island nation of Antigua and Barbuda to investigate the cost-optimal mix of solar photovoltaics (PV), wind, and in the most novel contribution, concentrating solar power (CSP). These technologies, together with battery and hydrogen energy storage, can enable the aim of achieving 100% renewable electricity and zero carbon emissions. The motivation for this study was that while most nations in the Caribbean rely largely on diesel fuel or heavy fuel oil for grid electricity generation, many countries have renewable resources beyond wind and solar energy. Antigua and Barbuda generates 93% of its electricity from diesel-fueled generators and has set targets of becoming a net-zero nation by 2040 and having 86% renewable energy generation in the electricity sector by 2030, but the nation has no hydroelectric or geothermal resources. The modeled, optimal mix of renewable energy technologies presented here was found for Antigua and Barbuda by assessing the levelized cost of electricity (LCOE) for systems comprising various combinations of energy technologies and storage. Other factors were also considered, such as land use and job creation. It was found that 100% renewable electricity systems are viable and significantly less costly than current power systems, and that there is no single defined pathway towards a 100% renewable energy grid, but several options are available.

Visual data on the geographic distribution of carbon storage helps policy maker to formulate countermeasures on global warming. However, Taiwan, as an island showing diversity in climate and topography, had lacked valid visual data in distribution of forest carbon storage between the last to forest surveys (1993-2015). This study established a model to achieve an estimation that capable to demonstrate the distribution of forest carbon storage. This model uses land use, stand morphology, carbon conversion coefficient databases accordingly for 51 types of major forest in Taiwan. An estimation on 2006 was conducted and shows an overall carbon storage of 165.65 Mt C, with forest carbon storage per unit area of 71.56 t C ha–1, where natural forests and plantations respectively contributed of 114.15 Mt C (68.9%) and 51.50 Mt C (31.1%). By assuming no change in land use type, the carbon sequestration from 2006 to 2007 by the 51 forest types was estimated to be 5.21 Mt C yr–1 using historical tree growth and mortality rates. The result reflects the reality of the land use status and event of coverage shifting with time by combining to the two forest surveys in Taiwan.

One of the ramifications of the COVID-19 pandemic is that it has lent urgency to ongoing discussions on mental well-being. While standard techniques are available to diagnose mental health disorders such as depression, anxiety, and stress, ambiguity persists regarding the emotional aspect of well-being. Emotional well-being (EWB) is a recently developed concept that seeks to understand the contribution of emotions to one’s well-being. Interactive approaches for such investigations are recommended to understand people’s contextual experiences. In this study, we use a qualitative approach to examine the psychological impact of the built environment on its residents to formulate the desiderata for an ideal place based on their perceptions. We use personal construct theory and the associated qualitative repertory grid technique. We recruited 15 students from the United Arab Emirates University and obtained information on their perceptions of three built environments they experienced. The findings revealed information on the students’ emotional constructs that were associated with a set of design-related factors, and the way the ideal hostel should be characterized in response to these associations. These findings enrich our knowledge of EWB within built environments and can inform their future design by considering the emotional aspect of the well-being of residents.

This paper provides an optimization strategy for flexible operation at the system level, so as to guide the real-time flexible ramping of the power grid. Firstly, the concept of regional power grid flexibility was clarified, and the ramping factor is proposed as a flexibility metric. On this basis, taking the output priority of each node as the objective function and considering constraints such as line flow, power balance, and system flexibility, a mathematical model for regional power grid transmitting flexible power externally is proposed. Compare with the traditional models, this model focuses more on flexibility rather than economy. The case analysis based on the improved IEEE 30-Bus System verifies the feasibility and effectiveness of the proposed strategy and its advantages over the traditional models.

The construction industry has witnessed the increasing use of digital tools and smart solutions, particularly, in the realm of buildings energy automation within the concept of smart cities. While to truly realize the potential benefits of smart cities, a broader scope of smart initiatives is required to support the transition from smart buildings towards smart neighbourhoods, appreciated as the critical unit of urban development. To support this interplay of smart solutions between buildings and neighbourhoods, this article aims to collect and review all smart solutions presented in existing scientific articles, technical literature, and realized European projects. These solutions are classified under two main sections of buildings and neighbourhoods, which are investigated through five domains: buildings energy-related uses, renewable energy sources, water, waste, and open space management. Showcasing the quantitative outcomes demonstrates the potential benefits of implementing smart solutions from buildings to neighbourhoods. Moreover, this research concludes that the true enhancement of energy conservation goes beyond the buildings’ energy component and can be genuinely achieved by integrating intelligent elements of the neighbourhood, due to their strong interdependencies. Future research is recommended to focus on assessing the effectiveness of these solutions towards resource conservation.

- Power grids of the future will likely incorporate more renewable energy distributed generation (REDG), also known as alternative energy systems. REDG units are increasingly being used in electrical transmission networks because to the overall positive effects they have on power networks. REDG systems are the backbone of smart electric networks and are essential to the operation of the smart grid. These REDG systems can additionally improve system reliability by providing some customers with a backup generator in the event of power interruptions. The report offers a thorough evaluation of the existing body of information on the topic of electric vehicles' (EVs') future interactions with the smart grid. The combination of the EVs' potential deployment and the smart grid's conceptual goal presents challenges in electric grid infra-structure, communication, and control. The proposal for connecting EVs to the grid is based on research into cutting-edge smart metering and communication systems. In the context of the vehicle-to-grid (V2G) phenomenon, the possibilities, benefits, and limitations of various EV smart charging systems are also fully examined. There is a fast growing percentage of distributed energy that is wind and solar photovoltaic. Their variable power output, however, introduces fresh challenges for those responsible for organizing, operating, and controlling the power grid. While fluctuations in the electric grid are problematic, they may be mitigated by the entry of EVs into the energy market. As such, we do a comprehensive literature search to learn more about the exciting research gap that needs to be filled and the most recent possible answer that involves EVs. Additionally, we take a close look at the practicality of the sophisticated V2G technology. The smart grid is a developing concept for the world's energy infrastructure, and this study analyzes in depth how EVs interact with it.

Here we present calculation of the critical current of DC SQUID based on the Josephson junction on multi-band superconductor with frustration effect. It is shown that the changing of the critical current of DC SQUID with small geometrical inductance is determined by the ratio of supercurrent amplitude in different channels and the external magnetic field. In the a case of DC SQUID with high inductance frustration effects can be ignored.

The use of smart grids has enabled a number of planning methods to be developed to optimize energy costs, Peak to Average Ratios (PARs), and consumer satisfaction for load management in industrial, commercial, and domestic sectors. From a technical point of view, achieving optimal outcomes requires Demand Side Management (DSM). In smart grids, utility companies and electric users communicate two-way using digital technology to make a sustainable and economic system. This paper proposes a novel framework within which an Energy Management Controller (EMC) keeps track of each appliance, its operational time, and the costs associated with them. Customers of smart grids are motivated to shift their Off-Peak Hours (OPH) from Peak Hours by presenting incentives in OPH. The metering devices would also save customers costs by preventing load shifting between high- and low-cost periods. In addition, the study proposes the bacterial foraging algorithm and grasshopper optimization algorithm for lessening power price and PAR without compromising user comfort (UC) through appliance planning. The simulation results on a practical test system advocate the high effectiveness and reliable performance of the proposed model.

In interceptive treatments in which impacted teeth (incisor or first permanent molar) should be included into the dental arch, the main clinical problem is the provision of an anchorage area and a suitable appliance. The use of laser sintered metal orthodontic grids, designed and printed digitally, has expanded the boundaries of orthodontic treatment, especially in its interceptive phase. Our aim is to describe a digital model for providing anchorage during orthodontic-surgical traction of impacted teeth in the mixed dentition period. We present the treatment of three clinical cases with digitally projected and printed metal grids used for anchorage. In the described clinical cases, individually designed anchorage systems were used. They were created through design software and after that the metal grids were printed. The devices are placed in the oral area and don’t disturb the aesthetics of the patient in any way. The advantages of individual designed metal support grids allow to accommodate the features of relief of the hard palate and alveolar bone. This makes the grids comfortable for the patient and rigid enough to perform orthodontic tractions at the same time. The printed additional grids are applicable in mixed dentition and in complicated clinical cases in permanent dentition. Their individuality allows segmental treatments or treatments in cases requiring additional anchorage further from the active force.

High-precision ground point cloud data has a wide range of applications in various fields, and the separation of ground points from non-ground points is a crucial preprocessing step. Therefore, designing an efficient, accurate, and stable ground extraction algorithm is of great significance for improving the processing efficiency and analysis accuracy of point cloud data. The study area in this article was a Park in Guilin, Guangxi, China. The point cloud was obtained by utilizing the UAV platform. In order to improve the stability and accuracy of the Filter algorithm, this article proposed a triangular grid filter based on Slope Filter, found violation points by the spatial position relationship within each point in the triangulation network, improved KD-Tree-Based Euclidean Clustering, and applied it to the non-ground points extraction, this method has good accuracy, stability and achieves good results in separating ground points from non-ground points. At first, using Slope Filter to remove some non-ground points, to reduce the error of taking ground points as non-ground points; Secondly, established a triangular grid based on the triangular relationship between each point, the violation-triangle can determin through the grid, and then the corresponding violation points were found in the violation-triangle; Thirdly, according to the three-point collinear method to extract the regular points, used these points to extract the regular landmarks by KD-Tree-Based Euclidean Clustering and Convex Hull Algorithm; Finally, removed disperse points and irregular landmarks by Clustering Algorithm. In order to confirm the superiority of this algorithm, this article compared the filter effects of various algorithms on the study area and filtered the 15 sample data provided by ISPRS, and obtained an average error of 3. 46%. The results showed that the algorithm in this article have a high processing efficiency and accuracy, which can greatly improve the processing efficiency of point cloud data in practical applications.

The rapid growth of Earth's global geospatial data necessitates an efficient system for organizing the data, facilitating data fusion from diverse sources, and promoting interoperability. Mapping the spheroidal surface of the planet presents significant challenges, as it involves balancing distortion and splitting the surface into multiple partitions. The distortion decreases as the number of partitions increases, but at the same time the complexity of data processing increases, since each partition represents a separate data set and is defined in its own local coordinate system. In this paper, we propose the dual orthogonal equidistant cylindrical projection method to mitigate distortion and reduce the number of partitions. Additionally, we use the rotation of projection cylinders to effectively minimize average angular and areal distortions of the Earth’s landmass and reduce the interruption of continental plates caused by partition edges. By incorporating auxiliary latitudes and proposing an approximate authalic latitude, we further enhance the mapping of the ellipsoid onto the sphere, simplifying calculations. Experimental results demonstrate a substantial reduction in distortion and interruption of continental plates. With only two partitions, an average landmass angular distortion of less than 3.56 degrees and an average normalized surface distortion of less than 1.07 were achieved.

This paper presents a comprehensive study and the analysis of a topology of a no isolated DC-DC intituled Double Quadratic Boost converter with high static gain. This converter has the main advantage of high static gain and low voltage stress on its switches. The article will first present the theoretical analysis of the converter operating in an open loop. The objective of the work is the mathematical modeling and the control strategy of the converter, as well as the validation through closed-loop experimental results. Besides, we presented the practice test results to demonstrate the operation of the converter, such as the static gain experimental curve, the practice efficiency of the converter, and the control of the output voltage, as well as the capacitor voltage balance control. The authors designed a prototype for 1 kW, with a switching frequency of fs=50kHz, with FPGA-based command and modulation.

Background Successful treatment for patients with metastatic colorectal cancer who failed to response to first-line treatment has been a challenge due to their low response rate for later-line treatment and poor progression free survival and overall survival. The application of dendritic cell-cytokine-induced killer cells (DC-CIK) immunotherapy combined with conventional treat-ment, either surgical resection or chemotherapy, showed improvement in survivals in first-line treatment for metastatic colorectal cancer. In this retrospective study, we aimed to evaluate the benefit of dendritic cell-cytokine-induced killer cells (DC-CIK) immunotherapy for patient with refractory metastatic colorectal cancer. Methods A total of 20 patients with refractory metastatic colorectal cancer receiving cell-cytokine-induced killer cells (DC-CIK) immunotherapy were enrolled to this study. Among these patients, 11 patients responded to the treatment and the remaining 9 patients did not. All patients were followed for at least one years and the determination of treatment response was mainly based on image study at 6 months after the completion of treatment. Data were analyzed with Kaplan-Meier method and log-rank test. Results The treatment response rate of the study group is 55% (11/20). The median progression free sur-vival (PFS) and median overall survival (OS) of responsive patients was 7 months and 12 months, respectively. The median overall survival of irresponsive patients was 9.5 months. Four responsive patients received subsequent metastectomy or cytoreduction plus hyperthermic in-traperitoneal chemotherapy surgery (CRS + HIPEC). Conclusion DC-CIK cell-based immunotherapy may provide benefits for patients with refractory mCRC with improved response rate and progression free survival.

Stray current is a relevant phenomenon in particular for DC electrified transportation systems, affecting the track and infrastructure within the right of way and other structures and installations nearby. It worsens with time and the level of protection depend on timely maintenance, besides correct design choices. The assessment of track insulation is the starting point for both stray current monitoring systems and at commissioning or upon major changes. Standardized methods (ref. EN 50122-2, or IEC 62128-2) are almost unchanged in the last 20 years, but suffer from accuracy issues and variability due to parameters and conditions not under operator’s control. A critical discussion and analysis of the sources of variability and practical constraints is proposed, followed by the evaluation of uncertainty, with the objective not only to assess the accuracy of provided results, but to foster research on innovative, more flexible and accurate, methods.

While traditional AC mechanical circuit breakers have been competent for protecting AC circuits, high penetration of DC power distribution technologies like DC microgrids (MGs) obligate better disruption performance features such as quick and reliable switch-ing speeds. However, a DC circuit breaker (DCCB) novel design is challenging due to the need to quickly break high currents within milliseconds, caused by the high fault current rise in DC grids compared to AC grids. In DC grids, the circuit breaker must provide zero current crossing and be designed for absorbing surges since the arc is not naturally extinguished by the system. Additionally, the DC breaker must mitigate the magnetic energy stored in the system inductance and withstand residual over-voltages after current interruption. These challenges require a fundamentally different topology for DCCBs, which are typically made using solid-state semiconductor technology, metal oxide varistors (MOV), and ultra-fast switches. This study aims to provide a comprehensive review on development, design, and performance description of DCCBs in parallel with a specific concentration on analysis of internal topology, energy absorption path and sub-circuits in Solid-State (SS)-based DCCBs. The research explores various novel designs that introduce different structures for energy dissipation solution. The classification of these designs is based on the fundamental principles of surge mitigation and a detailed analysis of the techniques employed in DCCBs. In addition, our framework offers an advantageous reference point for the future evolution of SS-circuit breakers in numerous developing power delivery systems.

Electric vehicles (EVs) will have a greater need for the amount of electricity needed to charge them as their popularity grows. It is anticipated that in order to accomplish this objective, it will be essential to implement a variety of solutions for grid transportation that are designed to complement one another and to make significant changes to the transmission infrastructure. It is possible to reduce the amount of energy that is lost on the power network through strategic planning and control, which may include economic models and methods to engage and reward users. This would eliminate the need for grid upgrades. Charging electric vehicles can also assist alleviate problems with transmission systems that are caused by the allocation of electric vehicles (EVs) using bidirectional charging method. The most significant problems that can occur with a transmission network are power loss and unstable voltage. Adding EV units to the transmission network is typically an effective method for resolving these challenges. As a result, EVs need to have the appropriate arrangement and dimensions. This research establishes where and how many electric vehicles (EVs) should be in a radial transmission network both before and after the adjustment is made. An artificially intelligent (AI) approach, known as a hybrid genetic algorithm particle swarm optimization (HGAIPSO), is used both before and after the radial network modification to find the optimal EV location and size. When electric vehicles are coordinated in an active transmission network, power losses are decreased, voltage profiles are raised, and system stability is increased. These benefits can be attributed to the greater use of electric vehicles. The simulation found that incorporating EVs into the testing system resulted in a considerable decrease in the quantity of power that was wasted. The minimal bus voltage of the system also undergoes similar kinds of enhancements. According to the findings of the comparative study, the proposed method mitigates both the voltage fluctuations and the power losses that occur in the transmission system. For type 1, type 2, and type 3 EV allocations, the IEEE-30 bus test system reduced real power loss by 40.70%, 36.24%, and 42.94%, respectively. IEEE-30 bus voltage reaches 1.01 pu.

Interference on Power Line Communication (PLC), which is a wired communication technology that provides communication and data transmission over the existing electrical network, is examined in this paper. Many applications employ PLC technologies, which have the benefit of leveraging existing power connections for both power and data transfer, reducing cost and complexity. These interactions may be observed in contemporary smart grids and automobile power networks, where lengthy cables, switching power supplies, and communication links all work together but exacerbate electromagnetic interference problems. This research examines the effects of Spread Spectrum methods used to reduce EMI from power converters on PLC systems. Spread spectrum modulation and its three variants Sine, Random and Triangle are frequently employed to meet the requirements of electromagnetic compatibility, however there are some repercussions, that might be detrimental to the converter or the rest of the electrical network. These outcomes occur for various modulation algorithm settings and at various frequencies. Measurements are made utilising the Frame Error Rate value provided by the PLC link system to ascertain the interference produced by a SiC-based DC-DC converter in order to investigate these concerns and standardise an assessment approach.

In this paper, a fuzzy logic-based energy management system and multi-port quasi-z-source converter are proposed that utilizes hybrid renewable energy sources. The system ensures that each energy source module can be used individually by employing fuzzy logic to define power modes. This approach also helps prevent switching losses resulting from extra switching of the source modules. Also, the proposed energy management does not have a mathematical model, so applicability is simple and it is suitable for different multiple input topologies. The Mamdani fuzzy inference system can be designed to capture the nonlinear behavior of the system because of the linguistic rules. Moreover, by adopting the quasi-z-source network to the end of the multi-port converter, the switching losses of the multi-port modules have been significantly reduced. The simulation results are obtained using MATLAB Simulink, and the experimental results are obtained by connecting the circuit to MATLAB Simulink via an Arduino Due.

Integrating numerous renewable resources has been extensively researched and studied to create a dependable energy system. This study investigated the best techno-economical hybrid energy system configuration while using hydrogen energy to keep the system's energy balanced. Additionally, this study aims to determine the best hybrid system configuration for the location under investigation. A novel technique of DBM (Deterministic Balanced Method) was introduced to determine the total annual energy output for the project's lifetime. This approach is used to contrast the outcomes of other HOMER software tools. Then, using HOMER, it is possible to confirm the sizing optimization results for the suggested method by comparing the power ratings and yearly energy output. A detailed comparison between our proposed method and HOMER Pro has been conducted for validation and verification. Our method has been rigorously tested in various hybrid off-grid energy systems, ensuring its applicability and reliability across different scenarios and configurations. The results of our study indicate a high degree of similarity between the proposed approach and HOMER pro for computing annual energy power for the studied energy systems. Specifically, our analysis revealed that the difference between the approaches was within a range of 5%, indicating a high level of consistency and reliability in our method. These findings suggest that our approach can be confidently applied to determine the appropriate size of hybrid energy systems accurately. Overall, our study provides valuable insights into the development of effective sizing methodologies for hybrid energy systems. After considering the amount of solar radiation and wind speed gathered by global weather data platforms like NASA and METEONORM, this paper has also included a real case study of the Cairo International Airport's hybrid renewable energy production systems. To guarantee the viability of this study, the system design was founded on an actual load that was researched and simulated. A cluster of distributed networks was finally proposed to use the excess energy and enable energy conversion processes to be used in industry and transportation applications.

This research proposes a roof-mounted auxiliary power supply (APS) system for 600VDC low-floor light rail vehicle (LRV). The proposed APS system consists of five parallel-connected dc-ac inverter modules (modules 1-5). The inverter modules 1 and 2 are three-phase dc-ac inverters for compressor motors of the cooling system, and the inverter modules 3 and 4 are three-phase dc-ac inverters for air pump motors of the braking system. The inverter module 5 is single-phase dc-ac inverter for 220VAC power supply for onboard electric loads. Simulations and experiments were carried out under variable load torque and output frequency for modules 1 – 4; and under full and no resistive loads for the inverter module 5. The measured total input current and total input power of the proposed APS system under full load condition are 118.76A and 71.25kW. Essentially, the proposed APS system is operationally applicable to the 600VDC low-floor RLV. Besides, the novelty of this research lies in the use of five parallel-connected inverter modules, unlike in the conventional APS systems which require three-phase output transformer or isolated dc-dc converter. Specifically, the proposed APS system requires neither three-phase output transformer nor isolated dc-dc converter.

Grid refinement is used to save computing costs while preserving high precision of fluid simulation. In the Lattice Boltzmann Method, grid refinement often uses interpolated values. We found a method, where interpolation in space and time is not required. For this purpose, we used the moment matching condition and rescaling the non-equilibrium part of populations, and developed the recalibration procedure that allows to transfer information between different LBM stencils in the simulation domain. Then, we build non-uniform lattice which uses stencils with different shapes on the transition. The resulting procedure is verified on the 2D Poisselle flow and the advected vortex benchmark. In prospect, grids with adaptive geometry can be built with the use of the proposed method.

In the era of electrification and artificial intelligence, direct current motors are widely utilized with numerous innovative adaptive and learning methods. Traditional methods utilize model-based algebraic techniques with system identification, such as recursive least squares, extended least squares, and autoregressive moving averages. The new method known as deterministic artificial intelligence asserts physical-based process dynamics to achieve target trajectory tracking. There are two common autonomous trajectory generation algorithms: sinusoidal function and Pontryagin's based generation algorithm. This thesis aims to simulate model-following and deterministic artificial intelligence methods using sinusoidal and Pontryagin's methods and compare their performance difference when following challenging step function slew maneuver.

The concepts of fractional calculus and the related techniques have been gaining momentum in circuit system fields, and an increasing body of evidence suggests that fractional-order characteristics are widely distributed in electronic components. In this paper, we consider the fractional characteristics of non-solid aluminum electrolytic capacitors and focus on the nonlinear dynamic characteristics of peak-current-mode controlled (PCMC) dc-dc boost converters with such components. In the work, we establish a piecewise smooth non-commensurate fractional-order model to describe the converter, in which the fractional-order equivalent impedance model of capacitors is adopted and the detailed control loop is considered. In order to analyze the converter, we use the fractional Adams-Bashforth-Moulton typed method (F-ABM) and stroboscopic map technique to obtain the time-domain solutions and the bifurcation diagram. The results of bifurcation diagrams indicate that, with the change of different parameters, the converter enters chaotic state through period doubling bifurcation. In order to provide empirical evidence for the nonlinear dynamic analysis, we consider both circuit-level simulation and experiments in the work, the results of which further confirm the results of theoretical analysis.

From the standpoint of Neoliberal Institutionalism, this study explores Malaysia's participation in activities that make energy the topic and/or object of foreign policies, whether through bilateral or multilateral engagements. This research, which aims to evaluate the relevance of energy in Malaysia's economy and diplomacy and to explain Malaysia's reason for its involvement in these cooperations, is necessary because of Malaysia's growing involvement in the global energy market. Information for this study was gathered from a variety of government sources, interviews, published statistical data, and previous studies. The study demonstrates how vital energy is to Malaysia's economy. The Lao PDR-Thailand-Malaysia-Singapore Power Integration Project (LTMS-PIP) initiative, in which Malaysia is participating, is evidence of the viability of multilateral power commerce in the area. The Peninsula Gas Utilisation (PGU) pipeline in Peninsular Malaysia and the Four-Fuel Diversification Policy 1981 (4FDP 1981), which increases natural gas utilisation, are related to Malaysia's participation in the Malaysia-Thailand Joint Development Area (MT-JDA). Malaysia would want to think about streamlining its energy administration.

This paper presents a comprehensive review that highlights the characteristics of non-isolated step-up converters based on high boost voltage lifting techniques. The paper categorises the high boost techniques: multistage/multilevel, switched capacitor, voltage multiplier, voltage lift, switched inductor, and magnetic coupling. The paper also discusses in detail the advantages and disadvantages for each category such as cost, complexity, power density, reliability and efficiency. The number of passive and active components, voltage gain, voltage stress, switching frequency, efficiency and power rating are also compared. Although the paper considers coupling inductors in the context of the non-isolated converter, the focus of the entire article is on the non-isolated high voltage step-up techniques. The key contribution in this paper is the review of high boosting techniques rather than the DC /DC converters. This allows divergence of new ideas and new power converters that will help provide highly efficient and flexible power converters for several applications where the sending end voltage is very low as photovoltaic systems. In addition, many applications and control techniques of DC/DC converters are summarised in this paper.

Based on the analysis of the working principle, circuit design and working loss of the common charger DC/DC converter, this paper designs a ZVS half-bridge three-level DC/DC converter based on non-phase-shift control mode, and proposes a multi-stage constant current and voltage limiting charging control strategy based on modulation wave selection control. The simulation results show that the proposed method and control strategy have faster voltage regulation ability and wider stability margin, and can achieve stable current sharing control in the charging process.

Microgrids offer flexibility in power generation in a way of using multiple renewable energy sources. In the past few years, microgrids become a very active research area in terms of design and control strategies. Most of the microgrids use DC/DC converters to connect renewable energy sources to the load. In this paper, the simulation model of a DC microgrid with three different energy sources (Lithium-ion battery (LIB), photovoltaic (PV) array, and fuel cell) and external variant power load is built with MATLAB/Simulink and the simulative results show that the stability of DC microgrid can be guaranteed by the proposed maximum power point controller MPPT. The three energy sources are connected to the load through DC/DC converters, one for each. This type of topology ensures protection for each energy source as well as optimum stability at the load.

Discretization is the process of converting a continuous function or model or equation into discrete steps. In this work, adaptive and learning methods are implemented to control DC motors that are used for actuating control surfaces of unmanned underwater vehicles. Adaptive control is a method in which the controller is designed to adapt the system with parameters which vary or are uncertain. Parameter estimation is the process of computing the parameters of a system using a model &amp; measured data. Adaptive methods have been used in conjunction with different parameter estimation techniques. Deterministic artificial intelligence, a learning-based approach that uses the process dynamics defined by physics, is also applied to control the output of the DC motor to track a specified trajectory. This work goes further to evaluate the performance of the adaptive &amp; learning techniques based on different discretization methods. The results are evaluated based on the absolute error mean between the output &amp; the reference trajectory and the standard deviation of the error. The first order-hold method of discretization and surprisingly large sample time of seven tenths of a second yields over sixty percent improvement over the results presented in the prequel literature.

In this paper, the authors consider the influence of the type of power supply and the internal parameters of the DC-DC converter on the stability of the system at constant power load. The stability of the system under consideration is important in the design and development of the power supply system for an autonomous consumer. Such a typical system can be a DC microgrid. In the work, when analyzing the stability of the system, the power source is not considered an ideal voltage source, but the active-inductive nature of the voltage source is taken into account, which is equivalent to using a synchronous machine with permanent magnets. The Rauss-Hurwitz algebraic criterion was used as a criterion for analyzing the stability of the system. This will make it possible to build and analyze the areas and boundaries of the system's stability. As a result, the areas and boundaries of the stability of the system were presented. The general trend towards the behavior of the zone of instability of the system was given. At the same time, dependences describing the boundaries of instability are presented, which are combinations of parameters of the DC-DC converter, beyond which the system becomes unstable. The presented definitions of the instability limits can be used as a corrective device of the control system to ensure the stability of the system in the upper limits of the power consumption.

The integrated DC-DC converter is appropriate for use in many domains, namely, display, cellular, and portable applications. This paper presents an integrated monolithic voltage-mode DC-DC boost converter with a low-power control circuit. The driver circuit requires an integrated converter to power up a digital logic circuit and converts the unregulated DC input to the controlled DC output at the desired voltage level. It is the integration of both power switches and control circuitry within the same CMOS technology to buck down and boost voltages using a switch mode regulator. In order to increase power efficiency in the DC-DC boost converter that provides low-power operation with a small chip size, a low-voltage operation is applied to the unique circuit characteristic. The operational transconductance amplifier(OTA), comparator, and oscillator in the control circuit are designed with the supply voltage of 3.3V and the operating frequency of 5.5 MHz. A compensator is used to create a pole that has sufficient phase margin for high stability. The DC- DC boost converter is measured in both experiment and simulation. Testing of the proposed circuit on the 0.35μm CMOS process shows that the output transient time of the amplifier can be controlled within of 7μsec and the output voltage is accurately controlled with a ripple ratio of 3%.

A significant number of persons with coronavirus disease 2019 (COVID-19) experience persistent, recurrent, or new symptoms several months after the acute stage of severe acute respiratory syndrome coronavirus 2 (SARS‑CoV‑2) infection. This phenomenon, termed Post-Acute Sequelae of SARS-CoV-2 (PASC) or Long COVID, is associated with high viral titers during acute infection, a persistently hyperactivated immune system, tissue injury by NETosis-induced micro-thrombofibrosis (NETinjury), microbial translocation, complement deposition, fibrotic macrophages, the presence of auto-antibodies, and lymphopenic immune environments. Here, we review the current literature on the immunological imbalances that occur during PASC. Specifically, we focus on data supporting common immunopathogenesis and tissue injury mechanisms shared across this highly heterogenous disorder including NETosis, coagulopathy, and fibrosis. Mechanisms include changes in leukocyte subsets/functions, fibroblast activation, cytokine imbalances, lower cortisol, autoantibodies, co-pathogen reactivation, and residual immune activation driven by persistent viral antigens and/or microbial translocation. Taken together, we develop the premise that SARS-CoV-2 infection results in PASC as a consequence of acute and/or persistent single or multiple organ injury mediated by PASC determinants to include degree of host response (inflammation, NETinjury), residual viral antigen (persistent antigen) and exogenous factors (microbial translocation). Determinants of PASC may be amplified by co-morbidities, age, and sex. Keywords: long COVID, PASC, long haulers, NETosis, T cell, NK cell, DC, neutrophil,

Electrifying off-grid and isolated islands in the Philippines remains one of the challenges that hinders community development. One of the solutions seen to ensure energy security, expand energy access and promote a low carbon future in this isolated islands is the use of renewable energy sources. This study wishes to determine the nearshore wave energy resource during monsoon seasons in Cuyo Island using a 40-year wave hindcast and 9-year on-site wind speed data to develop high resolution wave energy model using SWAN wave model, and assessed its annual energy production through matching with wave energy devices. Results shows that average significant wave height (Hs), peak period (Tp) and wave power density (Pd) during northeast monsoon are Hs = 1.35 m, Tp = 4.79 s and Pd = 4.05 kW/m respectively, while southwest monsoon which is sheltered by the mainland resulted to a lesser outcome, Hs = 0.52 m, Tp = 3.37 s and Pd = 0.34 kW/m. While the simulated model was observed to overestimate the wave energy resource (Bias = 0.398, RMSE = 0.54 and SI = 1.34), it has a strong relationship with the observed values (average r = 0.9). Its annual energy production is highest at Station 5, with AEPWaveBouy = 43.761 MWh, AEP-Pelamis = 216.786 MWh and AEPWave Dragon = 2462.66 MWh. At present, the minimum requirement for a wave energy development to be feasible is 5 kW/m, which in this case, Cuyo Island falls short, but with the continuous evolution of wave energy converters, applications on milder re-sources will soon materialized.