Ti-Al alloy phase layer/Ti-Al carburizing composite coating was prepared on the surface of titanium alloy by the stepwise coating method of hot dip aluminization and then carburizing. The weight gain results of the composite coating showed that the titanium alloy coated with the composite coating had long-term stability (≥16 days) at 800oC. The microstructure, phase structure and composition of the composite coating were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS).The composite coating is composed of an alloy phase layer and a carburized layer. The natural transition of four phases (Ti3Al/TiAl/TiAl2/TiAl3) in the alloy phase layer, significantly improves the interfacial bonding between the coating and the substrate, and slows down the propagation of microcracks through the coating.Al2O3, TiC and C in the carburizing layer improve the surface hardness of the coating, and TiAl2 and Al2O3 also have excellent oxidation resistance at high temperature.

Bulk composition, mineralogy and microchemistry of various fractions of the filling of the Crater No. 4 at Emmerting were investigated. Here we present mainly the fine fractions, which, in contrast to pebbles larger than ca. 4 cm, are relatively poor in material affected by melting. A 0.1 mm long meteorite fragment without ablation features was found, and remelted fragments of the same body have been identified. The projectile was dominated by enstatite, also containing forsterite, basic plagioclase, Ni-rich pyrrhotite and troilite, kamacite, silica, and probably merrillite. The molten fragments contain porous Mg-rich glass (indicating temperature > 1500 °C), minor Fe oxides, and occasionally uncommon Ni-rich minerals. The bulk composition and electron microprobe show that the amount of meteoritic material is low (<< 1 %), and it is not unequivocally manifested even in platinum-group elements abundances and osmium isotope ratios (the latter, however, were only measured in two samples). This can be explained by dilution of the filling by particles brought after the crater formation, and by probably achondritic composition of the projectile. Relatively large hollow spheroid Fe oxide particles were observed in thin sections from the magnetic fraction. A Mn oxide hollow spherule has also been found. In magnetically separated filling from the nearby Crater No. 5, bulk chemical composition points to contamination with several metals and metalloids probably due to influence of recent alluvial sediments. Therefore, the extent of meteoritic contamination in this crater may be even smaller.

Magnetic pulse welding (MPW) employs high pulsed magnetic field to accelerate parts against each other thus forming an impact joining. Single-turn tool coils and field-shapers (FS) used in MPW operate under the most demanding conditions: a magnetic field of 40-50 T with a period of tens of microseconds. For conventional copper and bronze coils intense thermo-mechanical stresses lead to rapid degradation of the working bore. This work is aimed to improve the efficiency of field-shapers and focused on development of 2- and 4-slit FS with nanocomposite Cu 18Nb wire brazed as FS inner current-carrying layer. The measured ratio of magnetic field to discharge current was 56.3 and 50.6 T/MA for 2- and 4-slit FS respectively. FEM calculations of magnetic field generation showed its 6-9% and 3% variation for 2- and 4-slit FS respectively. The results of copper tube compression have shown an ovality of 27% and 7% for 2- and 4-slit FS respectively. The measured deviation of weld joining length was 11% and 1.4% in 2- and 4-slit FS respectively. Compared to the previous experiments on the whole steel inductor, the novel FS showed significantly better results in terms of efficiency and homogeneity of the magnetic field.

This study focuses on the analyses of nano-twinned Copper (Cu) films deposited through magnetron sputtering on Silicon Carbide (SiC) chips. The investigation encompasses the utilization of Chromium (Cr) adhesive layer coupled with varying voltage bias conditions. The goal is to comprehensively examine the influence of adhesive layer and negative bias voltages, contributing to an enhanced understanding of materials engineering and bonding technologies for advanced applications. The formation of a nanotwinned structure and (111) surface orientation can be properly controlled by applied substrate bias. High density nanotwinned structures were introduced into Cu films sputtered on SiC substrates with 82.3% of (111)-orientation proportion at -150 V much higher than the Cu film sputtered with another substrate bias. It is concluded that the sputtered Cu nanotwinned film formed with -150 V bias voltage has the potential to be employed as the interlayer for low temperature direct bonding.

Reactions in water between the Cu2(µ-EGTA) chelate (EGTA = ethylene-bis(oxyethyleneimino)tetraacetate(4-) ion) and 2,6-diaminopurine (Hdap) in molar ratios 1:1 and 1:2 yield only blue crystals of the ternary compound [Cu4(μ-EGTA)2(μ-H(N3)dap)2(H2O)2]·7H2O (1) that has been studied by single crystal X-ray diffractometry, various physical methods (thermal stability, spectral and magnetic properties), as well as DFT theoretical calculations. In the crystal, uncoordinated water is disordered. The tetranuclear complex molecule also has some irrelevant disorder in an EGTA-ethylene moiety. In the complex molecule, both bridging organic molecules act as binucleating ligands. There are two distorted five- (type 4+1) and two six- (type 4+1+1) Cu(II) centres. Each half EGTA acts as a tripodal tetradentate Cu(II) chelator, with mer-NO2+O(ether, distal) conformation. Hdap exhibits the tautomer H(N3)dap, with the dissociable H-atom on its less basic N-heterocyclic atom. These features favour the efficient cooperation between Cu-N7 or Cu-N9 bonds with appropriate O-EGTA atoms, as N6-H···O or N3-H···O interligand interactions respectively. Bridging role of both organics determines the tetranuclear dimensionality of the complex in 1. In this crystal, such molecules associate in zig-zag chains, built by alternating ,-interactions between the five- or six-atom rings of Hdap ligands of adjacent molecules. DFT theoretical calculations (using two different theoretical models and characterized by the quantum theory of “atoms in molecules”) reveal the importance of these ,-interactions between Hdap ligands, as well as that corresponding to the referred hydrogen bonds in the contributed tetranuclear molecule.

Growing interest has accrued in the co-existence of cardiac amyloidosis and valvular heart disease. Amyloid infiltration from either transthyretin (ATTR) or light chain (AL) origin may affect any structure of the heart, including the valves. Recent literature has mainly focused on aortic stenosis and cardiac amyloidosis, improving our understanding of epidemiology, diagnosis, treatment and prognosis of this dual pathology. Even though of high clinical relevance, data on mitral/tricuspid regurgitation and cardiac amyloidosis is rather scarce and mostly limited to case reports and small cases series. It is the aim of this review article to summarize the current evidence of concomitant valvular heart disease and cardiac amyloidosis including epidemiology, diagnostic approaches, screening possibilities, therapeutic management, and prognostic implications.

Understanding the infiltration and solidification processes of liquid 5083Al alloy into Al2O3 three-dimensional reticulated porous ceramic (Al2O3(3D) RPC) is essential for optimizing the microstructure and properties of Al2O3(3D)/5083Al interpenetrating phase composites (IPCs) prepared by low-pressure infiltration process (LPIP). This study employs ProCAST software to simulate the infiltration and solidification processes of liquid 5083Al with pouring velocities (PV) of 0.4 m/s infiltrating into Al2O3(3D) RPC preforms with varying porosities at different pouring temperatures (PT) to prepare Al2O3(3D)/5083Al IPCs using LPIP. The results demonstrate that pore diameter of Al2O3(3D) RPC preforms and PT of liquid 5083Al significantly influence the of the infiltration. Solidification process analysis reveals that the Al2O3(3D) RPC preform with smaller pore diameters allows the lower pouring velocity of 5083Al to solidify faster compared to the preform with larger pore diameters. Al2O3(3D)/5083Al IPCs were prepared successfully from Al2O3(3D) RPC porosity of 15 PPI with liquid 5083Al at PV 0.4 m/s and PT 800 °C using LPIP, resulting in nearly fully dense composites, where both Al2O3(3D) RPCs and 5083Al interpenetrate throughout the microstructure. The infiltration and solidification defects were reduced under air pressure of 0.3 MPa (corresponding to PV of 0.4 m/s) during LPIP. Finite volume method simulations are in good agreement with experimental data, validating the suitability of the simplified model for Al2O3(3D) RPCs in the infiltration simulation.

We investigate the ammonium removal abilities of natural and synthetic zeolites, which have distinct Si/Al ratios and various surface areas, to study how adsorption and ion-exchange processes in zeolites perform under different ammonium concentrations and different temperatures. Five zeolites including natural mordenite, chabazite, erionite, clinoptilolite and synthetic merlinoite were immersed in 20 mg/kg, 50 mg/kg and 100 mg/kg ammonium solutions. The results demonstrate that zeolites under high ammonium concentrations (100 mg/kg) possess higher physical adsorption capacity (0.398–0.468 meq/g), whereas those under lower ammonium concentrations (20 mg/kg) possess greater ion-exchange property (64–99%). The ion-exchange ability of zeolites are extremely dependent on the cation content of the zeolites, and the cation content is affected by the Si/Al ratio. The surface area of zeolites also has a partial influence on its physical adsorption ability. When the surface area is less than 100 m²/g, the adsorption ability of zeolite increases obviously with surface area; however, adsorption ability is saturated as the surface area becomes larger than this critical value of 100 m²/g. When we carried out the zeolites in 50 mg/kg ammonium concentration at different temperatures (5~50 ℃), we found that zeolites exhibit the highest ammonium removal ability at 30°C and the potassium release was enhanced at 30~40 ℃.

As Li-ion batteries use is spreading, incidents in large energy storage systems (stationary storage containers, …) or in large-scale cell and battery storages (warehouse, recyclers, …), often leading to fire, are occurring on regular basis. Water remains one of the most efficient fire extinguishing agents for tackling those battery incidents and large quantities are usually necessary. Since bat-teries contains various potentially harmful components (metals and their oxides or salts, sol-vents…) and that thermal runway induced battery incidents are accompanied with complex and potentially multistage fume emissions (containing both gas and particles) the potential impact of fire run-off water on the environment should be considered and assessed carefully. The tests presented in this paper focus on the analysis of the composition of run-off waters used to spray NMC Li-ion modules under thermal runaway. It highlights that waters used for fire-fighting are susceptible to contain many metals, including Ni, Mn, Co, Li and Al mixed with other carbonaceous species (soot, tarballs) and sometimes undecomposed solvents used in the elec-trolyte. Extra-polation of pollutant concentrations compared with PNEC values showed that, for large scale incidents, run-off water could be potentially hazardous to the environment.

Cobalt oxide nanoparticles are promising candidates for various kinds of practical application. The interest of researchers and scientists in these nanoparticles is due to their unique physical and chemical properties such as density, melting point, magnetic characteristics and band gap. The need to develop high performance and low-cost technologies for obtaining Co3O4 nanoparticles is a major reason in research in this area. The widespread commercial use of Co3O4 nanoparticles will open doors for numerous novel cost effective technologies, which are mostly dependent on the type of synthesis method and raw materials. A possible solution to this problem is to use Cobalt nitrates as a cost-effective precursor using the solution combustion method. Solution combustion synthesis method is one of the best candidate methods that have the potential for high performance and is also cost-effective. This review examines recent progress in the synthesis of Co3O4 nanoparticles by solution combustion method and underscores their significance across various fields, highlighting the need for further research and exploration of their multifaceted applications. In addition, the most recent advancements in the applications of Co3O4 nanoparticles in sensitive sensing, catalysis, supercapacitors/batteries and water treatment/pollutants removal are reviewed and described, focusing on current trends, challenges, and future outlooks.

Although Sn has been intensively studied as one of the most promising anode materials to replace commercialized graphite, its cycling performance and rate performance are still unsatisfactory owing to insufficient control of its large volume change during cycling and poor electrochemical kinetics. Herein, we propose a Sn-TiO2-C ternary composite as a promising anode material to overcome these limitations. The hybrid TiO2-C matrix synthesized via two-step high-energy ball milling effectively regulated the irreversible lithiation/delithiation of the active Sn electrode and facilitated Li-ion diffusion. At the appropriate C concentration, Sn-TiO2-C exhibited significantly enhanced cycling performance and rate capability compared to its counterparts (Sn-TiO2 and Sn-C). Sn-TiO2-C delivers good reversible specific capacities (669 mAh g-1 after 100 cycles at 200 mA g-1 and 651 mAh g-1 after 500 cycles at 500 mA g-1) and rate performance (446 mAh g-1 at 3000 mA g-1). The superiority of Sn-TiO2-C over Sn-TiO2 and Sn-C was corroborated by electrochemical impedance spectroscopy, which revealed faster Li-ion diffusion kinetics in the presence of the hybrid TiO2-C matrix than in the presence of TiO2 or C alone. Therefore, Sn-TiO2-C is a potential anode for next-generation Li-ion batteries.

Garnet-type Ta-doped Li7La3Zr2O12 (LLZO) ceramic solid electrolytes with Ga2O3 additive were synthesized via a conventional solid-state reaction process. When the amounts of Ga2O3 additive were below 2 mol %, the sintered sample has a dense structure composed of grains with the averaged size of 5 to 10 μm, while 3 mol % or more Ga2O3 addition causes the significant increase in grain size above several 10 to 100 μm, due to the sintering with large amount of liquid Li-Ga-O phase at high temperature. The highest total (bulk + grain-boundary) ionic conductivity of 1.1 mS cm1 at room temperature was obtained in the sample with 5 mol % Ga2O3 addition. However, in galvanostatic testing of the symmetric cell with Li metal electrodes, this sample was shorted by Li dendrite growth into solid electrolyte at current density below 0.2 mA cm2. The tolerance for Li dendrite growth is maximized in sample sintered with 2 mol % Ga2O3 addition, which was shorted at 0.8 mA cm2 in the symmetric cell. Since the interfacial resistance between Li metal and solid electrolyte was nearly identical among the all samples, the difference in tolerance for Li dendrite growth is mainly attributed to the difference in microstructure of sintered samples depending on the amounts of Ga2O3.

In this work commercial 18650 lithium-ion cells with LiMn₂O₄, LiFePO₄ and Li(Ni_0.33Mn_0.33Co_0.33)O₂ cathodes were exposed to external heating in an Accelerating Rate Calorimeter (es-ARC, THT Company) to investigate the thermal behavior under abuse conditions. New procedures for measuring external and internal pressure change of cells were developed. The external pressure was measured utilizing a gas-tight cylinder inside the calorimeter chamber in order to detect venting of the cells. For internal pressure measurements, a pressure line connected to a pressure transducer was directly inserted into the cell. During the thermal runaway experiments, three stages (low rate, medium rate and high rate reaction) have been observed. Both pressure and temperature change indicated different stages of exothermic reactions, which produced gases or/and heat. The onset temperature of thermal runaway was estimated according to temperature and pressure changes. Moreover, the different activation energies for the exothermic reactions could be derived from Arrhenius plots.

Digital microfluidics (DMF) devices enable precise manipulation of small liquid volumes in point-of-care testing. Printed circuit board (PCB) substrate is commonly utilized to build DMF devices. However, inkjet printing can be used to fabricate DMF circuits, providing a less expensive alternative to PCB-based DMF designs while enabling more rapid design iteration cycles. We demonstrate the fabrication process of the inkjet-printed DMF circuit. We compare Kapton and polymethyl methacrylate (PMMA) as dielectric coatings by measuring the minimal droplet actuation voltage for a range of actuation frequencies. The minimum actuation voltage of 5.6 V was required for droplet movement with the PMMA layer thickness of 0.2 μm and a hydrophobic layer of 0.17 μm. Significant issues with PMMA dielectric breakdown were observed at actuation voltages above 10 V. In comparison, devices that utilized Kapton were found to be more robust even at the actuation voltage up to 100 V.

Fresh Ag nanoparticles (NPs) dispersed on a transparent SiO2 exhibit an intense optical extinction band originating in localized surface plasmon resonance (LSPR) in visible range. The intensity of LSPR band weakened when the Ag NPs was stored in ambient air for two weeks. The rate of the weakening and the LSPR wavelength shift, corresponding to visual chromatic changes, strongly depended on the environment in which Ag NPs were set. The origin of a chromatic change was discussed along with both compositional and morphological changes. In one case, bluish coloring followed by a prompt discoloring was observed for Ag NPs placed near the ventilation fan in our laboratory, resulted from adsorption of large amounts of S and Cl on Ag NP surfaces as well as particle coarsening. Such color changes deduce the presence of significant amounts of S and Cl in the environment. In other case, a remarkably blue-shift of LSPR band was observed for the Ag NPs stored in the desiccator made of stainless steel, originated in the formation of CN and/or HCN compounds and surface roughening. Their color changed from maroon to reddish, suggesting that such molecules were present inside the desiccator.

This study aims to establish whether the use of biomaterials, particularly polydimethylsiloxane (PDMS), for surgical reconstruction of the esophagus with templates, Montgomery salivary tube, after radical oncology surgery for malignant neoplasia is an optimal choice for patients’ safety and for optimal function preservation and organ rehabilitation. Methods: Structural analysis by Raman spectrometry and biomechanical properties with dynamic mechanical analysis are performed for fatigue strength and toughness, essential factors in durability of a prosthesis in the reconstruction practice of the esophagus. Nanocomposites with silicone elastomers and nanoparticles used in implantable devices and in the reconstruction surgery are facing risks of infection and fatigue strength when required to perform a mechanical effort for long periods of time. Results: This report takes into account the effect of silver (Ag) nanoparticles on the fatigue strength using polydimethylsiloxane (PDMS) matrix, representative for silicon elastomers used in implantable devices. PDMS with 5% (wt) Ag nanoparticles of 100-150 nm during mechanical fatigue testing at shear strength loses elasticity properties after 400 loading-unloading cycles and up to 15% shear strain. The fatigue strength, toughness, maximum shear strength are the key issues in designing Montgomery salivary tube with appropriate biomechanical behavior for each patient. Conclusions: Prosthesis design needs to indulge both clinical outcome as well as design methods and research in the field of biomaterials.

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

Rare earth elements (REEs) and Sc are concentrated in aluminum production byproducts. The novel REEs recovery approach, which involves leaching by acid at a pH > 3 in the presence of MgSO4, results in the formation of a pregnant leach solution (PLS) with a low concentration of iron (Fe) and titanium (Ti) and a large quantity of valuable elements. The ion exchange method was acknowledged as the most favorable method used to separate the REEs from PLS. This work studies the application of chelating resin Puromet МТS9580 in the sorption recovery of Sc from sulfate solutions. To analyze the static Sc sorption data, Langmuir, Freundlich, and Temkin isotherm models were used. The Langmuir isotherm model was the best fitted to the experimental data, with a coefficient of determination (R2) of 0.983. The dynamic adsorption experiment was conducted using a PLS and a simulate solution without contaminants. Adsorption of Sc from the simulate solution was better fitted to the Thomas model with a Sc capacity greater than 7 mg mL–1. Because Ti had a gradual decrease in C/C0, which the Thomas model was unable to simulate, the modified dose-response (MDR) model fitted better with PLS. The NaHCO3 solution (200 g L–1) effectively desorbed Sc (>98 %) from simulated and PLS solutions after 1.5 h of stirring in a batch mode.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

The concept of green energy is now at the forefront of development discourse, with the United Nations Sustainable Development Goals (SDGs) 7, 11, and 12 all aimed at promoting green energy consumption to combat the three planetary crises: climate change, biodiversity loss, and pollution. Similarly, issues regarding Africa’s natural resource curse have caused a stir in the growth and development literature for some time now and there is no sign that it will die out. This study, the first of its kind, simultaneously assesses the impact of green energy consumption and Africa’s natural resources rents on economic growth by applying the Feasible Generalized Least Square (FGLS) estimator and the dynamic panel models of the Pooled Mean Group (PMG) and Mean Group (MG) estimators on data from 1990 to 2020 for 24 selected African countries. The results show that green energy consumption has a short-run growth-limiting effect and a long-run growth-enhancing effect in Africa. The study also found evidence of the natural resource curse phenomenon in Africa. The study, therefore, calls for the advancement and usage of green energy for both domestic and industrial production in Africa. The study further calls for a revamp in the global tax policy to curb illicit financial activities and strengthening institutional quality for transparency and accountability in the entire value chain of natural resource management in Africa.

The mechanism underlying microbiologically induced carbonate precipitation have not been thoroughly characterized, although numerous scholars and experts have specifically investigated questions regarding minerals induced by bacteria. The study of the precipitation of carbonate minerals induced by halophilic bacteria has aroused wide concern. The present study aimed to investigate the characterization and process of biomineralization in high salt systems by a halophilic bacterium, Chromohalobacter israelensis strain LD532 (GenBank: KX766026), which was isolated from the Yinjiashan Saltern in China. Carbonate minerals induced by LD532 were investigated in several sets of comparative experiments that employed magnesium sulfate and magnesium chloride as Mg resources. Magnesium calcite and aragonite were induced by LD532 bacteria, whereas these minerals did not appear in the control group. The mineral phases, micromorphologies, and crystal structures were analysed using X-ray powder diffraction, scanning electron microscopy, and energy dispersive X-ray detection. The carbonic anhydrase and urease secreted by strain LD532 through metabolism increased the pH value of the liquid medium and promoted the process of carbonate precipitation. Further study using high resolution transmission electron microscopy, energy dispersive X-ray detection and analysis of ultrathin slices showed that the nucleation sites of carbonate minerals were located on extracellular polymeric substances and the membranes of intracellular vesicles of LD532 bacteria, which provided favourable conditions for the growth of carbonate mineral crystals. The morphologies and compositions of minerals formed in solutions of MgSO₄ and MgCl₂ display significant differences, indicating that different sources of Mg²⁺ may also affect the physiological and biochemical activities of microorganisms and thus mineral deposition. This study will be of some interest for the interpretation of carbonate biomineralization in natural salt environments and has some value as a reference in understanding sedimentary carbonates in ancient marine environments, such as tidal flats.

In the present research, groups of nanolayered structures and nanohybrids based on organic green dyes and inorganic species are designated to act as fillers for PVA for inducing new optical sites and increasing its thermal stability through producing polymeric nanocomposites. In this trend, different percentages of Naphthol green B were intercalated as pillars inside the Zn-Al nanolayered structures to form green organic-inorganic nanohybrids. The two-dimensional green nanohybrids were identified by X-ray diffraction, TEM and SEM. According to the thermal analyses, the nanohybrid, which has the highest amount of green dyes, was used for modifying the PVA through two series. In the first series, three nanocomposites were prepared depending on the green nanohybrid as prepared. In the second series, the yellow nanohybrid, which was produced from the green nanohybrid by thermal treatment, was used to produce another three nanocomposites. The optical properties revealed that the polymeric nanocomposites depending on green nanohybrids became optical-active in UV and visible regions because the energy band gap decreased to be 2.2 eV. In addition, the energy band gap of the nanocomposites depended on yellow nanohybrids was 2.5 eV. The thermal analyses indicated that the polymeric nanocomposites are thermally more stable than that of the original PVA. Finally, the dual functionality of organic-inorganic nanohybrids that produced from the confinement of organic dyes and the thermal stability of inorganic species converted the non-optical PVA to optical-active polymer in a wide range with high thermal stability

Al has very good corrosion resistance and corrosion properties. The corrosion resistance of Al cast alloys is different because these alloys contain a lot of elements. Especially in secondary alloys which contain more impurity elements from which Fe is the most common. This study deals with secondary AlSi7Mg0.3 cast alloys which contain more Fe and are affected by a chloride corrosion environment. This environment was selected based on the application of castings in the automo-tive industry. The main object was to research the effect of such an environment on basic me-chanical properties and fatigue properties. The results show that a higher Fe content does not lead to a significant reduction in the properties of the casting and the chloride environment is not so harmful. Therefore, can be stated that the investigated secondary sand-cast experimental materials can replace the primary alloys without losing the required corrosion and mechanical properties.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

The removal of metal ions by biosorption on inexpensive materials is still a challenge for environmental engineering research. In this study, marine green algae biomass (Ulva lactuca sp.) and the biochars obtained from this biomass, at 320 C (BC-320) and 550 C (BC-550), were used as biosorbents for the removal of Cu(II) ions from aqueous solution. In addition to comparing the biosorption capacities, the determination of the thermodynamic parameters allows the choice of the most suitable material for the biosorption processes. The experimental results, obtained for Cu(II) ions biosorption on each biosorbent (algae biomass (AB), BC-320 and BC-550), at three different temperatures (10, 30 and 50 C) were analyzed using Langmuir and Freundlich isotherm models, while pseudo-first order, pseudo-second order and intra-particle diffusions models were used to model the kinetic data. The biosorption of Cu(II) ions is best described by the Langmuir model and the pseudo-second kinetic model, regardless of the type of biosorbent. The maximum biosorption capacity (qmax, mg/g) depends on the temperature, but also on the type of biosorbent, and follow the order: BC-320 < AB < BC-550. Using the experimental isotherms, the thermodynamic parameters (G0, H0 and S0) for the biosorption of Cu(II) ions on each biosorbent were calculated. The analysis of the obtained values constitutes the main arguments in choosing BC-550 as the most effective biosorbent for the removal of Cu(II) ions from aqueous media.

The photocatalytic biohydrogen generation using ZnO with the aid of simultaneous deposition of copper from an aqueous biomass-derivative glycerol solution was investigated. The effects of concentration of glycerol solution, Cu ion concentration and reaction temperature on biohydrogen generation were investigated. The photocatalytic biohydrogen production rate increased with increasing the concentration of aqueous glycerol solution, and the observed data could be fitted to the Langmuire-Hinshelwood kinetic models. The photocatalytic H2 production efficiency with ZnO could be significantly improved by simultaneous Cu deposition. The photocatalytic biohydrogen production rate was dependent on temperature, and increased with the increasing temperature. The possible mechanisms for oxidation of glycerol solution and photocatalytic hydrogen generation were proposed.

Here we report highly efficient, indium tin oxide (ITO)-free polymer solar cells (PSCs) with an ultrathin copper (Cu) film(~10 nm) coated with a thin layer of poly[(9,9-bis(3‘-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) as transparent electrode. Despite of its lower far-field transmittance of the electrode, the obtained ITO-free device based on the ultrathin Cu film can delivery higher absorption efficiency than that of the device based on ITO substrate in the long wavelength region, which can be attributed to the formation of metal resonant microcavity between the opaque back metal mirror (MoO3/Al electrode) and the transparent Cu film with high reflectance. As a result, polymer solar cells based on poly[[2,6'-4,8-di(5-ethylhexylthienyl)benzo[1,2-b;3,3-b]dithiophene][3-fluoro-2[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] (PTB7-Th) and [6,6]-phenyl C71-butyric acid methyl ester (PC71BM) blend show a high power conversion efficiency (PCE) of 8.21 %, comparable to that of the control device based on ITO electrode (with a PCE of 9.60% ). The results demonstrate that thermally evaporated Cu thin film electrode can be promising candidate to replace ITO for highly efficient PSCs, thus may open up the possibility for massive production of PSCs with low cost.

Transportation is the primary consumer of oil, accounting for a significant portion of global energy consumption (34%) and CO2 emissions (40%). Electrifying road transportation is crucial to mitigate the effects of global warming. The abundant potential of renewable energy sources like solar and wind is hindered by their intermittent nature and incongruity with peak energy demands. This calls for the development of sophisticated energy storage solutions. Metal-air batteries (MABs), emerging as viable alternatives to lithium-ion batteries (LIBs), have attracted considerable attention due to their promising applications in the transportation sector. Despite substantial progress in MAB development over the past two decades, overcoming critical challenges such as electrolyte decomposition, carbon cathode degradation, anodic dendrite growth, and air impurities remains essential for their commercial viability. This mini-review provides a comprehensive overview of MAB fundamentals and the challenges associated with their development. The insights presented in this review serve to illuminate the current landscape and future prospects of MABs in the transportation sector.

LiFePO4 (LFP) has undergone extensive research and is a promising cathode material for Li-ion batteries. The high interest is due to its low raw material cost, good electrochemical stability, and high-capacity retention. However, poor electronic conductivity and a low Li+ diffusion rate decrease its electrochemical reactivity, especially at fast charge/discharge rates. In this work, the volumetric energy density of lithium-ion batteries is successfully increased by using different amounts of conductive carbon (Super P) in the active material content. The particle size and morphology of the electrode material samples are studied using field emission scanning electron microscopy and dynamic light scattering. Two-point-probe DC measurements and adhesive force tests are used to determine the conductivity and evaluate adhesion for the positive electrode. Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and charge/discharge tests are used to analyze the electrochemical properties of the battery. The samples containing 88% LFP, 5.5% Super P and 6.5% PVDF perform best, with discharge capacities reaching 169.8 mAhg-1 at 0.1C, and they can also manage charging/discharging of 5C. EIS indicates that this combination produces the lowest charge-transfer impedance (67 Ω) and the highest Li+ ion diffusion coefficient (5.76 x 10-14 cm2s-1).

This paper focuses on the comparative analysis of lithium-ion batteries (LIB) thermal management with aim to maintain working temperature in the range 15 ℃ – 35 ℃. This is to prevent thermal runaway and high temperature gradients. The proposed approach is to employ the biodiesel, situated inside the diesel/LIB powered hybrid electric vehicle, to supply as fuel and coolant. A 3S2P LIB module is simulated using Ansys-Fluent CFD software tool. The system without a coolant shows that LIB has exceeded the optimum maximum temperature, which leads to shortened life-cycle and poor performance. Four fatty acid methyl ester biodiesels are used as coolants, namely palm, karanja, jatropha, and mahua oils. When compared with conventional methods of cooling, using air and 3M Novec liquid, the palm biodiesel coolant proves to be the best option to maintain LIB temperature within the optimum working range. With the use of palm biodiesel, the system is estimated to lightweight the BTMS by 43%, compared to the case when 3M Novec is used to maintain the same temperature range.

Egyptians face a significant challenge in meeting the growing population's water needs for agriculture and food production. To address this, policymakers and researchers have implemented the National Great Project for Lining and Rehabilitation of All Open Canals of the Irrigation Network to reduce irrigation water losses through seepage, evaporation, and evapotranspiration. The current field study evaluates water losses from the Al Maanna canal network in Assiut governorate, Middle Egypt, using empirical formulas and field ponding methods. The obtained results indicated that the Moleth-Worth formula is more compatible and gives results that are in good agreement with the field measurements carried out. The estimated seepage losses from the existing, distorted Al Maanna canal network using the Moleth-Worth formula and field ponding method were about 2.07 and 2.20 million m3/month, respectively. Also, the calculated maximum evaporation and evapotranspiration losses were about 0.086 and 1.133 million m3/month, respectively. Consequently, the total water losses might be about 3.42 million m3/month, representing nearly 13.63% of the Al Maanna canal’s total discharge. After completing the lining process, seepage losses from lined canals were determined to be only about 0.472 million m3/month using the ponding method, while evaporation and evapotranspiration losses will be significantly decreased after canal rehabilitation. Hence, lining the Al Maanna canal network can decrease the total water losses by about 84%, which is sufficient to recommend and encourage the lining processes where the value of the gained quantities of water exceeds all the implementation expenses, in addition to other moral, cultural, and environmental gains.

Nano Silicon carbide reinforced aluminum (Al/nanoSiC) metal matrix composites are attractive because of their superior properties such as high strength and stiffness, Application of aluminum in technological and structural application is growing steadily. The major limitation for metal matrix nano composites, however, is their propensity to brittle fracture. The new technologies and new materials are two basic aims for companies. In this research, the effect of addition Al/SiC nano particles on microstructure and mechanical properties of pure aluminum has been investigated. Pure aluminum powder and various fractions of SiC particles with an average diameter of 50 nm were milled by a high-energy planetary ball mill to produce nanocrystalline Al–SiC nanocomposite powders. Pressing and sintering applied to consolidate powders to tablet shape. Then the samples were rolled to cylindrical shape. The nano SiC Percentage were 0%, 2.5%, 5%, 7.5%, 10% , 12,5% and 15%. Mechanical tests such as tensile, hardness, fracture toughness and young’s modules measurement carried out to study the mechanical behavior of each alloy. Scanning electron microscopy was used to study the morphology and microstructure of nanocomposite powders and bulk samples. The role of wt% fraction of SiC nanoparticles was investigated. The results shows that the addition of SiC nano particles has significant influence on the microstructure and mechanical properties of composites and usually the optimum properties depends on wt% SiC.

Accurate, detailed and recent Information about land cover/use is important and much more needed for different aspects of sustainable development and environmental management. As remote sensing datasets are becomes one of the most important and effective tools to generate such information, this study aimed to generating land cover map for sub area in Al-Ahasaa Oasis, Saudi Arabia, by using and classifying a subset of Landsat-ETM+ image of the selected study area, as bases and required input for future studies and researches. Different image preprocessing techniques in addition to a will-known and widely used classification method (i.e., Maximum Likelihood classifier) were applied. To be reliable with the final product, accuracy assessment was carried out with 89% agreement and accepted according to the applied method. Different land cover classes were found in the study area, which includes (Sand dunes, Water bodies, Sabakha, Bare soil, Urban, and Agricultural lands). The study also revealed that the dominant land cover class is sand dunes with approximately ± 70% in area. The study strongly indicated that the area has long been affected by sand movement. Finally, the study suggested that, further researches with more advanced methods rather than traditional methods are needed in the future to support the findings of this study, with high degree of accuracy.

2-(5,6-diphenyl-1,2,4-triazin-3-yl)pyridinium dichloroiodate (I) (1) was synthesized by reacting 3-(2-pyridyl)-5,6-diphenyl-1,2,4-triazine with ICl in dichloromethane solution. The structural characterization of 1 by SC-XRD analysis was accompanied by elemental analysis, FT-IR, and FT-Raman spectroscopy measurements.

Hydrogen peroxide (H2O2) is an essential analyte for detecting neurodegenerative diseases and in-flammatory processes and plays a crucial role in pharmaceutical, food industry, and environmental monitoring. However, conventional H2O2 detection methods have drawbacks such as lengthy analysis time, high costs, and bulky equipment. Non-enzymatic sensors have emerged as promising alternatives to overcome these limitations. In this study, we introduce a simple, portable, and cost-effective non-enzymatic electrochemical sensor based on carbon black (CB) and silver nano-particle-modified δ-FeOOH (Ag/δ-FeOOH), integrated into a disposable electrochemical cell (DCell). Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and electrochemical impedance spectroscopy (EIS), confirmed successful CB and Ag/δ-FeOOH immo-bilization on the DCell working electrode. Electrochemical investigations revealed that the DCell-CB//Ag/δ-FeOOH sensor exhibited an approximately twofold higher apparent heterogene-ous electron transfer rate constant than the DCell–Ag/δ-FeOOH sensor, capitalizing on CB ad-vantages. Moreover, the sensor displayed excellent electrochemical response for H2O2 reduction, boasting a low detection limit of 22 µM and a high analytical sensitivity of 214 μA mM-1 cm-2. Notably, the DCell-CB//Ag/δ-FeOOH sensor exhibited outstanding selectivity for H2O2 detection, even in potential interferents such as dopamine, uric acid, and ascorbic acid. Furthermore, the sensor demonstrated its suitability for monitoring H2O2 in complex biological samples, as evidenced by H2O2 recoveries ranging from 92% to 103% in 10% fetal bovine serum. These findings underscore the considerable potential of the DCell-CB//Ag/δ-FeOOH sensor for precise and reliable H2O2 monitoring in diverse biomedical and environmental applications.

Mesoporous TiO2/reduced graphene oxide/Ag (TiO2/RGO/Ag) ternary nanocomposite with effective electrons transfer pathway is obtained by an electrostatic self-assembly method and photo-assisted treatment. Compared with bare mesoporous TiO2 (MT) and mesoporous TiO2/RGO (MTG), the ternary mesoporous TiO2/RGO/Ag (MTGA) nanocomposite exhibited superior photocatalytic performance for the degradation of MB under visible light, and the degradation rate reached 0.017 min-1, which was 3.4 times higher than that of MTG. It is proposed that Ag nanoparticles can form the local surface plasmon resonance (LSPR) to absorb the visible light and distract the electrons into MT, and RGO can accept the electrons from MT to accelerate the separation efficiency of carriers. The establishment of MTGA ternary nanocomposite make the three components act synergistic effect to enhance the photocatalytic performance.

Yellow nanorod Mg-MOF-74 was obtained by solvothermal synthesis method. XRD、N2 adsorption-desorption isotherms、SEM and TGA results suggest that the particle size of Mg-MOF-74 reaches 400 nm after the introduction of sodium acetate in the precursor of Mg-MOF-74. Besides, the morphology of Mg-MOF-74 was changed from cauliflower to rod particles. At the same time, the BET specific surface area and pore volume of Mg-MOF-74 were also increased a lot. Then the CO2 dynamic adsorption capacity of Mg-MOF-74 was measured by self-made fix bed under 30 ℃、0.1 bar CO2 partial pressure. The results show that the CO2 adsorption capacity of Mg-MOF-74-N2 reaches 3.67 mmol/g and its CO2 adsorption capacity remains unchanged after 10 times CO2 adsorption-desorption cycles.

In this paper, the phases in the Mg-Ti-O system using the 1:1 formulation of MgO:TiO2 mixing synthetic brucite of Mexican origin with TiO2 microparticles of high purity and with a heat treatment at 1100°C for 1 h were studied. The raw materials and formulation by XPS and DRX techniques were characterized. The results demonstrate the presence of different oxidation states in titania and the formation of different oxides in the Mg-Ti-O system when mixed and calcined at 1100°C; additionally, the formation of vacancies in the crystal lattice during the transformation from hexagonal brucite to magnesia with a cubic structure centered on the faces is estimated. With the results, its thermal behavior is warned based on the MgO-TiO2 phase diagram.

Biomineralization has become a research hotspot and attracted widespread attention in the field of carbonate sedimentology. In this study, Bacillus licheniformis DB1-9 was used to induce the calcium carbonate precipitation at different magnesium calcium molar ratios in the laboratory to further explore the biomineralization mechanism. Phylogenetic tree shows that the bacteria belongs to Bacillus licheniformis species. The ammonia and carbonic anhydrase can be released by this bacteria, resulting in the pH increase, and the carbonic anhydrase can also promote the hydration reaction of carbon dioxide and subsequently produce the bicarbonate and carbonate ions to elevate the supersaturation of calcium carbonate in the liquid culture medium to facilitate the precipitation of carbonate minerals. The calcites have a shape of rhombohedron, dumbell, and elongation, and aragonite often appears in the form of mineral aggregates, besides that there are also the spherical and the fusiform minerals. FTIR result shows there are some organic functional groups, such as C-O-C and C=O, beside of the characteristic peaks of the calcite and the aragonite, indicating that microbial metabolism is closely related to the mineral formation. The superthin slices of the bacteria analyzed by HRTEM, SAED, EDS and STEM show that the surface and EPS can adsorb a large number of calcium ions and magnesium ions and EPS may act as the nucleation sites, what’s more, the intracellular nanometer-scale sphere areas show the amorphous structures, and the intracellular calcium ions and magnesium ions suggeste that they can be transported from the outside to inside the cell by diffusion along the concentration grade from high to low. This study may provide some references to further understand the biomineralization mechanism induced by microorganisms in the laboratory and the field, and also helps to explore the reason of the transition of calcite sea to aragonite sea in the geological history.

During shearer operation, piston rod is susceptible to wear from invasion of pollutants, and then ruins sealing ring in hydraulic cylinder. This work attempts to conduct a systematical investigation of Cu-DLC (Cu-doped Diamond-like Carbon) film to improve the seal performance. Failure process of hydraulic cylinder was analyzed, and relevant parameters were determined. Several Cu-DLC films were deposited on the substrate of piston rod in a multi-ion beam assisted system, and their structures and combined tribological performances were investigated. As a result, dust particles attached to the piston rod may enter the cylinder, and damage the sealing ring under the radial force. Cu grains prefer to orientate (111) crystal plane with increase of Cu content, and may induce drop of hardness and internal stress for the film. Friction coefficient of the film ranges from 0.04 to 0.15, and rise of IG/ID ratio from 1.4 to 2.3 in Raman data indicates that bond transition from sp3-C to sp2-C may lower the friction coefficient. Modification mechanism of Cu-DLC film for the seal performance may come from synergistic effects of (i) contact force and friction heat induce the film graphitization, (ii) Cu doping improves toughness of the film and acts as a solid lubricant, and (iii) transfer layer plays a role of self-lubrication.

Renewable methanol, obtained from CO₂ and hydrogen provided from renewable energy, has been proposed as a way to close the CO₂ loop. In industry, methanol synthesis using the catalyst CuO/ZnO/Al₂O₃ occurs at a high pressure. We intend to make certain modification on the traditional catalyst in order to work at lower pressure, maintaining high selectivity. Therefore, three heterogeneous catalysts have been synthesized by co-precipitation in order to improve the activity and the selectivity to methanol under mild conditions of temperature and pressure. Certain modifications on the traditional catalyst Cu/Zn/Al₂O₃ were employed such as the modification of the synthesis time and the addition of Pd as a dopant agent. The most efficient catalyst among those tested was a palladium-doped catalyst, 5% Pd/Cu/Zn/Al₂O₃. This had a selectivity of 64% at 210C and 5 bar.

A series of dinuclear copper(I) N,C,N- and P,C,P-carbodiphosphorane (CDP) complexes using multidentate ligands CDP(Py)2 (1) and (CDP(CH2PPh2)2 (13) have been isolated and characterized. Detailed structural information was gained by single crystal XRD analyses of nine representative examples. The common structural motive is the central double ylidic carbon atom with its characteristic two lone-pairs involved into binding of two geminal L-Cu(I) fragments at Cu-Cu distances in the range 2.55 – 2.67 Å. In order to enhance conformational rigidity within the characteristic Cu-C-Cu triangle, two types of chelating side arms were symmetrically attached to each phosphorus atom: two 2-pyridyl functions in ligand CDP(Py)2 (1) and its dinuclear copper complexes 2-9 and 11, as well as two diphenylphosphinomethylene functions in ligand CDP(CH2PPh2)2 (13) and its di- and mononuclear complexes 14-18. Neutral complexes were typically obtained via reaction of 1 with Cu(I) species CuCl, CuI, and CuSPh or via salt elimination reaction of [(CuCl)2(CDP(Py)2] (2) with sodium carbazolate. Cationic Cu(I) complexes were prepared upon treating 1 with two equivalents of [Cu(NCMe)4]PF6, followed by the addition of either two equivalent of an aryl phosphine (PPh3, P(C6H4OMe)3) or one equivalent of a bisphosphine ligands DPEPhos, XantPhos or dppf. For the first time carbodiphosphorane CDP(CH2PPh2)2 (13) could be isolated upon treating its precursor [CH(dppm)2]Cl (12) with NaNH2 in liquid NH3. A protonated and a deprotonated derivative of ligand 13 were prepared and their coordination was compared to neutral CDP ligand 13. NMR analysis and DFT calculations reveal, that the most stable tautomer of 13 does not show a CDP (or carbone) structure in its uncoordinated base form. For most of the prepared complexes, photoluminescence upon irradiation with UV light at room temperature was observed. Quantum yields (PL) were determined to 36% for dicationic [(CuPPh3)2(CDP(Py)2)](PF6)2 (4) and to 60% for neutral [(CuSPh)2(CDP(CH2PPh2)2] (16).

Researchers from around the world are looking for better and cheaper ozone production. One of the methods increasing the efficiency of ozone production is the use to a rotating electrode presented in this paper. Experiments were carried out which shows that the most important parameters are the materials used on the electrodes and the condition of its surface. The metallographic investigations of the electrodes after continuous monthly work was made, which show how the raids layers are formed. As a result of working in a highly oxidizing environment, the electrode is oxidized in the process of chemical corrosion. It is obvious that the layer of corrosion products created during the work of the plasma reactor isolates the surface of the electrode, which reduces the intensity of the electric field, causing a decrease in the amount of plasma generated, which is a direct cause of lowering the concentration of ozone during this process. The dynamics of plasma generation process and the type of electrode material working in changing process conditions are the decisive factors influencing the concentration of ozone produced. The influence of the medium, which is the electrode material, depends mainly on its resistance to corrosion in the environment of dynamically changing conditions, e.g. electrode rotation, oxygen flow through the rotating electric field and the long monthly working time of the plasma reactor.

Currently, companies and SMEs (small and medium enterprises) are looking to be more competitive. In order to achieve this, they are adopting new business models and strategies that allow them to move towards sustainability. Strategies such as CSR (Corporate social responsibility) and supply chain management have become essential for ensuring a company’s permanence and financial consolidation. The literature has stated that the theories of Stakeholders and Sustainability are fundamental pillars for the development and sustained growth of business. The purpose of this article is to examine the effects of CSR and the SC (supply chain) on innovation, image and reputation, and in turn, their influences on profitability in SMEs. This research is based on a sample of 143 companies in the city of Guaymas Sonora, in Mexico. For the analysis and validation of the results, we used the SEM (Structural Equation Modeling) statistical technique based on the variance, through PLS (Partial Least Squares) (using SmartPLS version 3.2.6 Professional). The findings show that SMEs that develop social and sustainable practices increase their level of innovation, and improve their image, their reputation, and their financial profitability. This work contributes mainly to the development of Stakeholders and Sustainability.

Li-rich manganese-based cathode materials (LRMs) are considered one of the most promising cathode materials for the next generation lithium-ion batteries (LIBs) because of their high energy density. However, there are problems such as capacity decay, poor rate performance, and continuous voltage drop, which seriously limit their large-scale commercial applications. In this work, Li1.2Mn0.54Co0.13Ni0.13O2 coated with Li2MoO4 with unique spinel structure was prepared by wet chemistry method and the subsequent calcination process. The Li2MoO4 coating layer with spinel structure can provide a 3D Li+ transport channel, which is beneficial for improving rate performance, while protecting LRMs from electrolyte corrosion, suppressing interface side reactions, and improving cycling stability. The capacity retention rate of LRMs coated with 3wt% Li2MoO4 increased from 69.25% to 81.85% after 100 cycles at 1C, and the voltage attenuation decreased from 7.06 to 4.98 mV per cycle. The lower Rct also exhibits improved magnification performance. The results indicate that the Li2MoO4 coating effectively improves the cyclic stability and electrochemical performance of LRMs.

Co-free Li-rich oxide is a promising cathode for low cost high energy density Li-ion battery but presents poor cyclic stability. To address this issue, CeO2 is coated on Co-free Li-rich oxide through a low-temperature aged process, resulting in a novel CeO2-coated Li-rich oxide compo-site. Due to the low-temperature aged process, a uniform CeO2 coating layer of 6 nm in thickness is successfully coated on Co-free Li-rich oxide. With this uniform coating, the resulting CeO2-coated Li-rich oxide composite presents improved cyclic stability as well as rate capability as the cathode of Li-ion battery. The capacity retention of the resulting CeO2-coated Li-rich oxide is enhanced from 67% to 85% after 100 cycles and its capacity retention of 5C/0.05C is enhanced from 10% to 23%, compared with the uncoated sample. Such significant improvements enable this low-temperature aged process to be helpful for the practical application of Li-rich oxide materials, not limited to Co-free Li-rich oxide.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

Obesity is treatment-resistant, and is linked with a number of serious, chronic diseases. Adult obesity rates in the United States have tripled since the early 1960s. Recent reviews show that an increased ratio of omega-6 to omega-3 fatty acids contributes to obesity rates by increasing levels of the endocannabinoid signals AEA and 2-AG, overstimulating CB₁R and leading to increased caloric intake, reduced metabolic rates, and weight gain. Cannabis, or THC, also stimulates CB₁R and increases caloric intake during acute exposures. The present meta-analysis reveals significantly reduced body mass index and rates of obesity in Cannabis users, in conjunction with increased caloric intake. We provide for the first time a causative explanation for this paradox, in which rapid and long-lasting downregulation of CB₁R following acute Cannabis consumption reduces energy intake and storage and increases metabolic rates, thus reversing the impact on body mass index of elevated dietary omega-6/omega-3 ratios.

The principal main of this research work was the study the influence of Cu addition on the wear behavior (WB) of eutectic Al-12.6Si alloy developed by spray forming (SF) method and compared with as-cast (AC) alloys. The phases of chemical compositions and microstructure were studied by optical microscopy, energy dispersive spectroscopy (EDS) and Scanning Electron Microscopy (SEM). The microstructure of SFAl-12.6Si (SF1) alloy reside — of fine primary and eutectic Si phases evenly distributed in the equiaxed α-Al matrix and SF Al-12.6Si-2Cu (SF2) alloy lie of uniformly distributed fine eutectic Si particulates and spherical form θ-Al2Cu precipitates in α-Al matrix. On other hand, the AC Al-12.6Si alloy (AC1) alloy involve of eutectic Si needles in the dendrite α-Al matrix, whereas AC Al-12.6Si-2Cu (AC2) alloy consisted of eutectic Si needles and Chinese script form θ phase distributed randomly in the α-Al matrix. The microhardness and wear properties were analyzed using Vickers hardness (VH) and dry sliding WT. The SF alloys exhibit superior hardness compared to the AC alloys. The wear properties of SF alloys exhibited significantly superior compared to the AC alloys. The SF2 alloy showed high wear resistance (WR) than the SF1 alloy in the entire sliding velocities and applied loads. The results indicate that the spray deposited alloys have a lower coefficient of friction (CF(µ)) than the AC alloys under varying load and sliding velocity conditions. The high WR in the SF alloy was due to microstructural modification during SF and precipitation of fine Al2Cu intermetallic and solid solubility effects. The SF2 depicts increased transition from oxidative to abrasive. In other ways, AC alloys demonstrate wear mechanisms that change from oxidative to abrasive and delamination with an increase in sliding velocity and load.

Enterobacteriaceae can contaminate meat during various stages of processing, including slaughter, evisceration, and butchering, causing foodborne illnesses. The purpose of the study was to investigate the prevalence of Enterobacteriaceae associated with carcasses obtained from slaughterhouses and raw cut meat collected from butcher shops. A total of 120 samples of camels and cattle were identified using biochemistry and PCR testing. Total viable count (TVC) was range from 4.91 to 5.37 Log10 CFU/g in slaughterhouses and butcher shops. E. coli was predominating with 84 (70%) among all samples, where the camels had the highest with 100% and sheep the lowest with 30%. Salmonella spp. was confirmed in 40% of camel samples, 47.5% of cattle samples, and 32.5% in sheep samples. Twenty-five Enterobacteriaceae genera were confirmed using PCR. Where sheep’s samples had the highest occurrence of Enterobacteriaceae with 15 different genera followed by camels and cattle samples with 14 different genera. The prevalence of Enterobacteriaceae among camel, cattle, and sheep carcasses raises significant concerns regarding food safety. Adherence to good hygiene practices throughout animal slaughtering is crucial to minimize the risk of infection and transmission and ensure food safety.

Thermal analysis of a hypereutectic Al-Si alloy used for an automotive part was carried out in this research work. Solidification characteristics are recognized from the Temperature-time curve and its corresponding derivatives. This analysis was successfully used in a simulation software program with the aim of improving the resultant simulation accuracy. In this study, different types of molds, with and without cooling systems, were designed and used. The melt present in the furnaces of the factory was used to simulate the casting process. The effect of different cooling rates (1.2ºC/s, 2ºC/s, 2.3ºC/s and 2.9ºC/s) on the solidification parameters have been investigated. Differences in the resultant microstructure between wall and center of the molds have been analyzed and have been related to the T-t curve. Finally, the experimental results clearly indicate that the water-cooling rate of the molds and the melt temperature directly affects the solidification process as well as the final microstructure.

This study involved the fabrication of a set of Aluminum ion-grafted SBA-15 utilizing ethylene-diamine and trimethylamine ionic liquids. The primary objective was to examine the impact of the fabrication environment on the physicochemical characteristics of the catalysts. Comprehensive characterization of the Al-SBA-15 catalysts was conducted using various techniques, including XRD, FTIR, surface area, pyridine FTIR, 27Al-NMR, TGA, HRTEM, and FESEM, to analyze their physicochemical characteristics. Furthermore, the acidic characteristics were examined by con-ducting potentiometric titration in a nonaqueous solvent and employing FTIR spectroscopy to an-alyze the chemisorbed pyridine. The effectiveness of the fabricated acid materials was evaluated by testing their performance in the acetic acid esterification with butanol. The findings obtained reveal that the mesostructured of SBA-15 remains intact following the successful inclusion of Al3+ ions into the silica frameworks. Additionally, a remarkable enhancement in the existence of both Bronsted and Lewis acid centers is noted due to the grafting process of Al3+ ions. At temperatures of 80°C and 100°C, the reaction in Al-SBA-15(T-120) proceeds swiftly, reaching approximately 32% and 38% conversion, respectively, within a span of 110 minutes. The excellent catalytic performance observed in the esterification reaction can be attributed to two factors: the homogeneous distribution of Al3+ ions within the SBA-15 frameworks and the acidic character of Al-SBA-15. The findings further indicate that the grafting process for incorporating Al3+ ions into the silica matrix is more efficient.

The drought is one of all phenomena at local to a global scale that caused climate change impacts, alongside it also the human activities related, which were deforested and land use changed that caused to ecological disturbance, which one is hydrological changes. Hence, it’s a lot of lost productivity, chiefly to farming land aspects and the other, so the land restoration by reforestation is needed in framework to water cycle (hydrology) process kindly. The aim of this research has identified and analyzed ecological restoration to ecosystem services, chiefly in wastewater management (treatment) to conservation, especially in Al Zaytun areas (Pesantren), so observing and in-depth individual interview (with some of personage and pesantren of boards) is one method that used to data collected, alongside land survey management to classified type development in Al Zaytun areas. The result of this research revealed that Al Zaytun successfully in water management to conservation by wastewater treated management by Eichhornia crassipes (Enceng gondok), afterward to the reservoir as water saved development. Those conservation types considered capability in reviving to ecological systems to ecosystem services increased kindly, alongside to land restoration by some of the plant species or trees to grow and developed in which Tectona grandis L. f is more dominantly and it's favorite because of investment economic that advantage based on ecological perspective. These were type management that did by Al Zaytun, alongside its able in coping to both drought and climate change impacts kindly and adaptively, and of course, it’s part of an obligation as the follower’s Islam religion in preserving and maintaining natural resources, chiefly to water resources.

The microstructure of Al-5Fe-1.5Er alloy was characterized and analyzed by using XRD, SEM, TEM and EDS. The effect of microstructure on the behavior of crack initiation and propagation was investigated by in situ tensile testing. Results show that the microstructure consists of α-Al matrix, Al₃Fe, Al₄Er, eutectic phase Al₃Fe + Al₄Er, while the 1.5 wt.% Er was added in Al-5Fe alloy. The twin structure of the Al₃Fe phase was observed, and the twin plane is {001}. Moreover, a continuous concave and convex interface structure of the Al₄Er has been found. Al₃Fe is in the form of a sheet with a clear gap inside.In situ tensile tests of the alloy at room temperature show that the crack initiation occured mainly in the Al₃Fe phase, and that the crack propagation modes include intergranular and transgranular expansion. Crack transgranular expansion is due to the strong binding ability between Al₄Er phases and surrounding organization, and the continuous concave and convex interface structure of the Al₄Er provides a significant meshing effect on the matrix and eutectic structure.

It is important for researchers in material domain to reconstruct and visualize the microstructure of alloy, which helps discover morphologies and properties that can only be found in three dimensional and microscopic space. However, because of the limitation of state-of-the-art sensors, the internal microstructure of the material is not easy to obtain. In this paper, a novel automatic 3D reconstruction method is proposed using diffraction contrast tomography technology to capture the 3D microstructure of Al-La alloy. The pipeline of the proposed method starts from the imaging of Al-La alloy with the LabDCT technique from Carl Zeiss AG, which produces a sequence of 2D microstructure sections. Then, a segmentation algorithm based on superpixel and lifted multicut is proposed to extract the 2D microstructure in an image section. Finally, 2D segmentations are joined together to reconstruct and visulize the 3D microstructure. As a result, a novel morphology of Al-La alloy is recovered with both dendrite and lamellar morphologies. The proposed method has the advantage of the ability to losslessly recover the internal microstructure.

Addressing the issue of low bonding strength in Ti/Mg laminated composites due to interfacial oxidation, this study employs a differential temperature rolling method using longitudinal induction heating to fabricate Ti/Mg composite plates. The entire process is conducted under an argon gas protective atmosphere, which prevents interfacial oxidation while achieving uniform deformation. The effects of reduction on the mechanical properties and microstructure of the composite plates are thoroughly investigated. Results indicate that as the reduction increases, the bonding strength gradually increases, mainly attributed to the increased mechanical interlocking area and a broader element diffusion layer. This corresponds to a transition from brittle to ductile fracture at the microscopic tensile-shear fracture surface. When the reduction reaches 47.5%, the Ti/Mg interfacial strength reaches 63 MPa, which is approximately a 20% improvement compared to the bonded strength with previous oxidation at the interface. Notably, at a low reduction of 17.5%, the bonding strength is significantly enhanced by about 1 time. Additionally, it is found that a strong bonded interface at high reduction is beneficial in hindering the propagation of interfacial cracks during tensile testing, enhancing the ability of the Ti/Mg composite plates to resist interfacial delamination.

Current Li battery technology employs graphite anode and flammable organic liquid electrolytes. Thus, current Li battery is always facing the problems of low energy density and safety. Additionally, sustainable supply of Li due to scarce abundance of Li sources is another problem. All-solid-state Mg battery is expected to solve the problems owing to non-flammable solid-state electrolytes, high capacity/safety of divalent Mg metal anode and high abundance of Mg sources. Therefore, solid-state electrolytes and all-solid-state Mg battery have been researched intensively last two decades. However, realization of all-solid-state Mg battery is still far. In this article, we review recent research progress on all-solid-state Mg battery so that researchers can pursue recent research trend of all-solid-state Mg battery. At first, solid-state electrolyte research is described briefly in the categories of inorganic, organic and inorganic/organic composite electrolytes. After that, the recent research progress of all-solid-state Mg battery is summarized and analyzed. To help readers, we tabulate electrode materials, experimental conditions and performances of all-solid-state Mg battery so that the readers can find necessary information at a glance. In the last, challenges to realize the all-solid-state Mg batteries are visited.

Nowadays, it is highly desired to develop highly active and humidity resistive ozone decomposition catalyst to eliminate the ozone contaminant, one of the primary pollutants in air. In this work, a series of Cu2S hollow structured materials are rapidly synthesized using different structured Cu2O templates. The Cu2S from porous Cu2O shows the highest ozone catalytic decomposition efficiency of >95% to 400 ppm ozone with a weight hourly space velocity of 480,000 cm3g-1h-1 in dry air. Importantly, the conversion still keeps >85% in a high relative humidity of 90%. The mechanism is explored by diffusive reflectance infrared spectroscopy which shows the decomposition intermediate of O22-, and the X-ray photoelectron spectroscopy reveals the dual active site of both Cu and S. All these results show the effective decomposition of ozone by Cu2S especially in harsh environments, promising for active ozone elimination.

It is found in this paper that ILR-RPCA-back CLR has two problems when dealing with the closure effect of geochemical data. (1) After ilr transformation, RPCA is used for processing. It can be seen from the double-plot diagram that the first principal component and the second principal component transform with the element sequence transformation, and the unique principal component cannot be calculated; (2) the score and the load are transformed into the CLR space through the U matrix. According to the formula CLR=ALR·U, the score result can correspond to the original order of elements. However, the load result obtained by the use of this formula cannot correspond to the original order of elements, and the result can only be obtained through the formula” CLR=UT·ALR”. In order to obtain the best element assemblage of porphyry copper deposit, this paper adopted the mineral assemblage of discovered deposits in Gangdese metallogenic belt for statistical analysis, and obtained that the element assemblage of porphyry copper deposit was Cu, Mo, Au, Ag, W, Bi. Then, by analyzing the singularities of the composite elements, the spatial overlay of the combined element is carried out, and C-A fractal filtering is applied to identify the anomaly and background. In order to facilitate comparison, the different minerals and ore deposit types have been analyzed, the results show that (1) in view of the porphyry copper deposits, recognition effect of combination elements are better than which single element, (2) skarn type copper deposit that it has nothing to do with the porphyry had a high degree of difference, but skarn type copper deposit related to the porphyry had a low degree of difference, (3) This method has a certain advantage over the single element method in porphyry gold deposits, and it can reduce the level of anomalies. Such an advantage is that in the aspect of anomaly evaluation of porphyry copper deposits, the level is reduced at the initial stage of evaluation to reduce the investment in such anomalies, (4) This method has limited ability to distinguish porphyry copper deposit from porphyry molybdenum deposit.

Copper is a heavy metal used in many industries and known for its negative impacts on the environment and human’s health. A novel structured metal organic framework (MOF) was used for copper adsorption for this work. SEM, EDAX, XRD and FTIR were done to confirm the structure of MOF prepared. MOF of 0.05 gm was used to examine its ability in Cu+ 2 removals with different initial concentrations of Cu+2 and pH values (5, 7 and 9). The prepared MOF was able to achieve Cu removal with 94.6%, 93%, 91.5%, and 92.5 % for the initial concentrations of 5, 10, 15, and 20 ppm respectively. It also performed very well for pH 5 and 7 with average removal ranging from 93.9%-95% for pH 5 and 7 for the initial concentrations of 5, 10, and 15 respectively which indicate that the prepared MOF is of high ability in Cu+ 2 removal.

In this study, the hot deformation of Cu-0.55Sn-0.08La (wt%) alloy was studied by gleeble-3180 testing machine at deformation temperatures of 400-700oC and various strain rates. The stress-strain curve showed that the hot deformation behavior of Cu-0.55Sn-0.08La (wt%) alloy was greatly affected by work hardening, dynamic recovery, and dynamic recrystallization. The activation energy Q was calculated as 287.141 kJ/mol , and hot compression constitutive equation was determined as ε ̇=[sinh(0.006388σ)]^12.123∙exp⁡(37.7505-287.141/RT). The microstructural evolution of the alloy during deformation at 400oC revealed the presence of both slip and shear bands in the grains. At 700oC, dynamic recrystallization grains were observed but recrystallization was incomplete. In sum, these results provided the theoretical basis for continuous extrusion process of alloys with promising future use.

Cinnamomum tamala leaf (CTL), also known as tejpat and Indian bay leaf, is used all over the world for seasoning, flavouring, and medicinal purposes. Numerous researchers are interested in exploring the nutritional and medicinal benefits of CTL due to their potential as nutraceuticals. These characteristics could be explained by the presence of several essential bioactive substances and lipid derivatives. There are no reports available on this species about its metabolites profile. In this work, rapid screen and identify chemical compounds in supercritical (SC)-CO2 extracts of CTL by use of UPLC-Q-TOF-MSE with multivariate statistical analysis approach was established in both negative and positive mode. As a results, a total of 166 compounds, including 66 monocarboxylic fatty acids, 52 dicarboxylic fatty acids, 27 fatty acid amides, and 21 others were tentatively identified based on accurate mass, and the mass spectrometric fragmentation pattern, out of which 142 compounds are common and found in all five CTL extracts. They displayed robust [M+H]+ and/or [M-H]- ions in both low- and high-energy collision-induced dissociations (CIDs). Based on chemical profiling and chemometric analysis, CTL4 (300bar/55°C) extract was found significantly more potent in other CTL’s extracts. A new mono- and di-carboxylic fatty acids, fatty acid amides and other essential bioactive compounds were separated within 20 min runtime and identified in CTL for the first time. The combination of UPLC-Q-TOF-MSE and chemometric analysis is a powerful method to rapidly screen the metabolites profile for the quality control of C. tamala leaf.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

Lithium-ion (Li-ion) batteries are becoming more common in portable electronic devices due to their high energy density, lack of memory effect, and high charge and discharge rate capabilities. Li-ion batteries are a relatively new technology, first marketed in the early 1990s, and research and development work are ongoing to improve safety and increase capacity, charge/discharge rate, and lifetime [1]. In this paper, we review the types and characteristics of Li-ion batteries and summarize charging methods and safety considerations. Following, we design and fabricate Li-ion battery and highlight the steps of fabrication that ensure fast charge/discharge rates that give the battery more reliability and high energy density

Li-ion cell designs, component integrity and manufacturing processes all have critical influence on the safety of Li-ion batteries. Any internal defective features that induce a short circuit, can trigger a thermal runaway: a cascade of reactions, leading to a device fire. As consumer device manufacturers push aggressively for increased battery energy, instances of field failure are increasingly reported. Notably Samsung made a press release in 2017 following a total product recall of their Galaxy Note 7 mobile phone, confirming speculation that the events were attributable to the battery and its mode of manufacture. Recent incidences of battery swelling on the new iPhone 8 have been reported in the media, and the techniques and lessons reported herein may have future relevance. Here we look deeper into the key components of one of these cells and confirm evidence of cracking of electrode material in tightly folded areas, combined with a delamination of surface coating on the separator, which itself is an unusually thin monolayer. We report microstructural information about the electrodes, battery welding attributes and thermal mapping of the battery whilst operational. The findings point to the most likely combination of events and highlights the impact of design features, whilst providing structural considerations most likely to have led to the reported incidences relating to this phone.

p-type Ag-N dual acceptor doped ZnO thin films with long electrical stability were deposited by DC magnetron reactive co-sputtering technique. After deposition, the films were annealed at 400 °C for one hour in a nitrogen-controlled atmosphere. The deposited films were amorphous. However, after annealing they crystallize in the typical hexagonal wurtzite structure of ZnO. The Ag-N dual acceptors were incorporated substitutionally in the structure of zinc oxide and achieving that the three samples presented the p-type conductivity in the ZnO. Initial electrical properties showed a low resistivity of from 1 to10^{−3} Ω.cm, Hall mobility of tens cm2/V.s and a hole concentration from 10^{17} to 10^{19} cm^{−3}. The electrical stability analysis reveals that the p-type conductivity of the ZnO:Ag,N films is very stable and does not revert to n-type, even after 36 months of aging. These results reveal the feasibility of using these films for applications in short-wavelength or transparent optoelectronic devices.

Surface-enhanced Raman spectroscopy (SERS) can boost the pristine Raman signal by ~ 108 times that could be exploited for producing innovative sensing devices with advanced properties. However, the inherent complexity of SERS systems restricts their further applications in rapid detection, especially in situ detection in narrow aera. Here, we construct an efficient and flexible SERS-based LOP sensor by integrating Ag/Au nanocap arrays obtained by Ag/Au coating polystyrene nanospheres on the optical fiber face. We obtain rich “hotspots” at the nanogaps between neighboring nanocaps and further achieve the excellent SERS performance with the assistance of laser induced thermophoresis on the metal film that can achieve high efficiency aggregation of detected molecules. We achieve a high Raman enhancement with a low detection limitation of 10-7 mol/L for the most efficient samples based on the above sensor. This sensor also exhibits good repeatability and stability under multiple detections, revealing the potential application in situ detection based on the reflexivity of optical fiber.

The Yb/Al multilayer films exhibit excellent theoretical reflectivity in the 54-90nm wavelength range. This study attempted to incorporate 1.5% wt.% of Si impurities into Al to suppress the crystallization of Al, reduce interfacial roughness, and enhance the actual reflectivity of the prepared Yb/Al multilayer films. The internal microstructure changes of the film layers before and after Si impurity doping were investigated using GIXRR, AFM, and XRD techniques. The reflectivity of two types of multilayer films, Yb/Al(1.5wt.%Si) and Yb/Al(pure), was tested to evaluate the effect of Si impurity on the film performance.

The effects of different pulse frequencies on the microstructure grain size and solid solubility of Al-9Si alloy were systematically investigated using OM, SEM, and EDS. The effects on the mechanical properties of the alloy were analyzed using micro-Vickers hardness tester and multifunctional friction tester. During the solidification process, the Al-9Si alloy is exposed to high-frequency electric current pulses with a current density of 300A/cm2 and frequencies of 0Hz, 500Hz, 1 000Hz, and 2 000Hz. The experimental results show that as the high-frequency pulse frequency increases, the Lorentz force also increases. The intense electromagnetic stirring leads to grain refinement. However, as the pulse frequency continues to increase, the combined effect of Joule heating and Lorentz force results in an enlargement of the melt zone and an increase in grain size. At a pulse frequency of 1 000Hz, the eutectic structure size of the Al-9Si alloy is optimal, with the average size reduced to 13.87μm and a dense distribution, effectively eliminating primary Si. The EDS results revealed that the high-frequency pulse led to a more uniform distribution of Si elements within the matrix, and the solid solubility of Si in the α-Al matrix increased to a maximum value of 1.99%, representing a 39.2% increase. At a pulse frequency of 1 000Hz, the sample demonstrates the most favorable mechanical properties, with the friction coefficient reaching a minimum value of 0.302, representing a 37.7% decrease in the average friction coefficient. The results demonstrate that high-frequency pulsing is an effective method for enhancing the mechanical properties of Al-9Si alloy.

Aluminum (Al) toxicity is the most common factor limiting the growth of alfalfa in acidic soil conditions. Melatonin (MT), a significant pleiotropic molecule present in both plants and animals, has shown promise in mitigating Al toxicity in various plant species. This study aims to elucidate the underlying mechanism by which melatonin alleviates Al toxicity in alfalfa through a combined physiological and transcriptomic analysis. The results reveal that 5 μM MT significantly alleviates Al-induced growth inhibition and preserves the morphology of root tip cells. Moreover, MT application reduces Al accumulation in alfalfa roots and shoots by 28.6% and 27.6%, respectively. Additionally, MT plays a crucial role in scavenging Al-induced excess H2O2 by enhancing the activities of superoxide dismutase (SOD), peroxidase (POD), and catalase (CAT), consequently reducing malondialdehyde (MDA) levels. The RNA-seq results reveal that MT application significantly upregulates the expression of xyloglucan endotransglucosylase/hydrolase (XTH) and carbon metabolism-related genes, including those involved in the glycolysis process, as well as sucrose and starch metabolism, suggesting that MT application may mitigate Al toxicity by facilitating the binding of Al to the cell walls, thereby reducing intracellular Al accumulation, and by improving respiration and the content of sucrose and trehalose. Taken together, our study demonstrates that MT alleviates Al toxicity in alfalfa by restoring redox homeostasis, enhancing Al binding to the cell wall, and modulating carbon metabolism. This research advances our understanding of the mechanisms underlying MT's effectiveness in mitigating Al toxicity, offering potential strategies for reducing Al accumulation in alfalfa.

Saudi Arabia consists mainly of desert land. However, it has big and small natural wetlands and artificial wetlands. Most of these wetlands are seen along the Red Sea and the Arabian Gulf coastal regions. Al-Asfar Lake, located in the Eastern Region of Saudi Arabia, is one of the historical landmarks of Al-Ahsa province. The primary lake water source is agricultural drainage water, which some refer to as an artificial lake. This paper mainly aims to reflect shade on the wetlands in Saudi Arabia in general and to show in detail the environmental impacts of Al-Asfar Lake on the ecosystem and biodiversity of the study area. The analytical review of the previous studies conducted in Al-Asfar Lake was adopted in this article. Hence, the impact of the lake on the land-use system, water quality and biodiversity was illustrated as the main outputs of the review analysis. However, the sustainable management of Al-Asfar Lake requires the stakeholders to adopt the wetland ecosystem health concept, which might lead to improving the lake's environmental conditions.

Fe- and Al-rich metapelite from the Transangarian segment of the Yenisey Ridge (East Siberia, Russia) is a potential new source of high-alumina refractories. The rocks have relatively high average contents of Al2O3 (20 wt.%) and Fe2O3 (7.91 wt%), moderate K2O (3.44 wt%), and low CaO (0.74 wt%). Their dominant mineral assemblages are andalusite + muscovite + margarite + chlorite + biotite + quartz or staurolite + kyanite or/and andalusite + chlorite + muscovite + biotite + quartz with ±garnet and ±plagioclase. Al2SiO5 polymorphs occur as up to 1.5 cm andalusite porphyroblasts and partial or complete pseudomorphs after andalusite (kyanite and staurolite). Accessories include abundant Fe-Ti oxides and sporadic REE-, Y-, Ca-phosphates; sulfides are negligible. The composition of Al2SiO5 concentrates obtained in laboratory by heavy-media and magnetic separation from ≥0.06 mm fractions meet all requirements for raw material of this type: >56 wt% Al2O3, <42 wt% SiO2, <1 wt% Fe2O3, <1.2 wt% TiO2, and <0.2 wt% (CaO+MgO). The andalusite, kyanite, and mixed ores yield 0.7-4.1 wt%, 0.7-2.2 wt%, and 1.9-6.0 wt% of concentrate, respectively. The best-quality ores rich in Al2SiO5 polymorphs reside in zones of contact and/or dynamic metamorphism superimposed over regional metamorphism of Al-rich rocks.

The effects of partial replacement of Si by Al on the microstructure, tensile properties, and Charpy impact toughness were investigated using 0.2%C-Si/Al-Mn-Cr-B TRIP-aided martensitic steels. The impact toughness was related to the microstructural and mechanical properties. The partial re-placement decreased the volume fraction of retained austenite and increased the mechanical stabil-ity, accompanied by softening and an increase in the volume fraction of the primary martensite. Resultantly, the partial replacement decreased strength and ductility. The impact absorbed energy (value) at 25 C was slightly increased by the partial replacement. The increased impact absorbed energy was mainly caused by high crack/void propagation energy due to the softened primary martensite and a small contribution of the stabilized retained austenite. The 50% shear fracture ductile-to-brittle transition temperature was marginally raised by the partial replacement. The raised transition temperature was mainly associated with an increase in a unit crack path of qua-si-cleavage/cleavage fracture.

The narrow process window during intercritical annealing and discontinuous yielding have limited the commercialisation of medium Mn steels. In this study, a double annealing process based on the commercial continuous annealing line is proposed. The cold-rolled medium Mn steels were first fully austenitized and quenched during the first annealing, followed by the intercritical annealing for reverted austenite transformation. The microstructure of duplex lath-shaped austenite and ferrite is produced and the steel exhibit a desirable continuous yielding during tensile deformation. Al is added into the medium Mn steel to enlarge the process window and to improve partitioning efficiency of Mn. The produced steel is more robust with temperature fluctuation during the industrial process due to the enlarged intercritical region. Mn partitioning is more efficient owing to elevated annealing temperature, which results in the improvement of ductility in the Al-added steel with increased austenite stability.

Myasthenia gravis (MG) is a disease characterized by typical clinical and immunopathogenic pe-culiarities, which correlate with age and sex/gender. Accordingly, MG patients show thymic al-terations and auto-antibodies productions, that can be the expression of a different pathogenetic mechanism related to age and gender. This determines, in relation to age at and sex/gender, a dif-ferent MG onset, prognosis, and outcome. Therefore, diverse MG forms can be identified, classi-fied, and characterized in relation to their different features, and precisely there are early onset and late-onset forms of MG. It has been hypothesized that the cause of appearance the two diverse forms of MG can be ascribed mainly to the diverse genetic and epigenetic factors. In this narrative review, we will analyze and discuss about the interplay of age- and sex-related factors (i.e. genet-ic and epigenetic factors) related to two different MG forms and how they contribute to their di-verse pathogenesis.

Calcium and magnesium are important not only for human health, but also for reducing problems related to the corrosive and aggressive effects of soft water on drinking water distribution materials. Experimental and mathematical modeling of the recarbonization process aimed at increasing the content of these biogenic elements in water was carried out using the novelty of a continuous laboratory and pilot scale fluidized bed reactors. Water remineralization using half-calcined dolomite (HCD) and carbon dioxide was used. The influence of operating conditions Q(CO2), freshwater inflow and HCD dose on quality indicators of treated drinking water (c(Ca2+), c(Mg2+), c(Ca2++Mg2+) and Ca/Mg) was studied. The results show that the concentration of Mg2+ is more significantly affected by the amount of HCD in the system and the flow of CO2. The influence of freshwater inflow on the Mg2+content is to a lesser extent. At a constant CO2 flow, therefore, as the tap water inflow increases, the Ca2+ content decreases and the Mg2+ content increases, which has results in a decrease in the Ca/Mg molar ratio. However, the Ca/Mg ratio can be effectively controlled by adding an appropriate amount of HCD at certain time intervals. Overproduction of ions is easily controlled by CO2 flow.

A novel gas-phase electrocatalytic system based on a low-temperature proton exchange membrane (Sterion) was developed for the gas phase electrocatalytic conversion of CO2 to liquid fuels. This system achieved gas-phase electrocatalytic reduction of CO2 at low temperatures (below 90 ºC) over a Cu cathode by using water electrolysis-derived protons generated in-situ on an IrO2 anode. Three Cu-based cathodes with varying metal particle sizes were prepared by supporting this metal on an activated carbon at three loadings (50, 20, and 10 wt%; 50%Cu-AC, 20%Cu-AC, and 10%Cu-AC, respectively). The cathodes were characterized by N2 adsorption–desorption, temperature-programmed reduction (TPR), and X-ray diffraction (XRD) whereas their performance towards the electrocatalytic conversion of CO2 was subsequently studied. The membrane electrode assembly (MEA) containing the cathode with the largest Cu particle size (50%Cu-AC, 40 nm) showed the highest CO2 electrocatalytic activity per mole of Cu, with methyl formate being the main product. This higher electrocatalytic activity was attributed to the lower Cu–CO bonding strength over large Cu particles. Different product distributions were obtained over 20%Cu-AC and 10%Cu-AC, with acetaldehyde and methanol being the main reaction products, respectively. The CO2 consumption rate increased with the applied current and the reaction temperature.

The design of binders plays a pivotal role in achieving enduring high power in lithium-ion batteries (LIBs) and extending their overall lifespan. This review underscores the indispensable characteristics that a binder must possess when utilized in LIBs, considering factors such as electrochemical, thermal, and dispersion stability, compatibility with electrolytes, solubility in solvents, mechanical properties, and conductivity. In the case of anode materials, binders with robust mechanical properties and elasticity are imperative to uphold electrode integrity, par-ticularly in materials experiencing substantial volume changes. For cathode materials, the se-lection of a binder hinges on the crystal structure of the cathode material. Other vital consid-erations in binder design encompass cost-effectiveness, adhesion, processability, and envi-ronmental friendliness. Incorporating low-cost, eco-friendly, and biodegradable polymers can contribute significantly to sustainable battery development. This review serves as an invaluable resource for comprehending the prerequisites of binder design in high-performance LIBs and offers insights into binder selection for diverse electrode materials. The findings and principles articulated in this review can be extrapolated to other advanced battery systems, charting a course for the development of next-generation batteries characterized by enhanced perfor-mance and sustainability.

Li-rich layered oxide cathode materials have become one of the most promising cathode materials for high-energy-density lithium-ion batteries owning to its high theoretical specific capacity, low cost, high operating voltage and environmental friendliness. Yet they suffer from severe capacity and voltage attenuation during prolong cycling, which blocks their commercial application. To clarify these causes, we synthesize 0.5Li2MnO3·0.5LiNi0.8Co0.1Mn0.1O2 (LL-811) with high-nickel-content cathode material by a solid-sate complexation method, and it manifests a lot slower capacity and voltage attenuation during prolong cycling compared to LL-111 and LL-523 cathode materials. The capacity retention at 1C after 100 cycles reaches to 87.5% and the voltage attenuation after 100 cycles is only 0.460 V. Combining X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscopy (TEM), it indicates that increasing the nickel content not only stabilizes the structure but also alleviates the attenuation of capacity and voltage. Therefore, it provides a new idea for designing of Li-rich layered oxide cathode materials that suppress voltage and capacity attenuation.

The search for new materials that could improve the energy density of Li-ion batteries (LIB) is one of today’s most challenging issues. Recently, cation-disordered lithium-excess metal oxides have emerged as a promising new class of cathode materials for LIB, due to their high reversible capacities and nice structural stability. However, a full structural model of the Li-transition metal (TM) sharing sublattice and the origin of short range ordering (SRO) of cation ions requires further investigation. In this work, we put forward a Monte Carlo strategy of building a cation-disordered rocksalt material supercell model. The cation ions of Li_1.0Ti_0.5Ni_0.5O₂ (LTNO) are placed at the FCC sublattice sites with the constraint of Pauling’s electroneutrality rule, instead of a random way. This constraint causes the Li-Ti and Ni-Ni clustering (the cation short range ordering). Based on this model, we discussed the relationship between the short range ordering, the local distorting, the theoretic capacity and the order-disorder strengths. A unified understanding of these factors in cation-disordered materials may enable a better design of disordered-electrode materials with high capacity and high energy density.

We have proposed a data-driven approach for designing mesoscale porous structures of Li-ion battery electrode with three-dimensional virtual structures and machine learning techniques. Over 2,000 artificial 3D structures assuming positive electrode composed of random packed spheres as active material particles are generated, and charge/discharge resistance has been evaluated using simplified Physico-chemical model. In this model, resistance from Li diffusion in active material particles (diffusion resistance), transfer resistance of Li+ in electrolyte (electrolyte resistance) and reaction resistance on the interface between active material and electrolyte are simulated based on mass balance of Li, Ohm’s law in and linearized Butler-Volmer equation, respectively. Using these simulation results, regression models via Artificial Neural Network (ANN) have been created in order to predict charge/discharge resistance from porous structure features. In this study, porosity, active material particle size and volume fraction, pressure in the compaction process, electrolyte conductivity, and binder volume fraction are adopted as features, associated with controllable process parameters for manufacturing battery electrode. As results, the predicted electrode resistance by ANN regression model is good agreement with the simulated values. Furthermore, sensitivity analysis and optimization of the process parameters have been carried out. The proposed data-driven approach could be a solution as a guiding principle for manufacturing battery electrode.

The present study describes the preparation of a composite material consisting of thermoplastic polyurethane-poly (n-isopropylacrylamide) (TPU-PNIPAM), which was employed for the se-lective adsorption separation of alcohol/water mixed solutions for the first time. The findings revealed that TPU and PNIPAM were interconnected through interchain hydrogen bonding, resulting in exposed hydrophobic isopropyl groups while covering the hydrophilic hydrogen bond sites. Selective separation of alcohols from alcohol/water mixed solutions occurred via London dispersion forces between alkyl groups. Increasing the PNIPAM load on the TPU surface led to a decrease in available hydrogen bond sites capable of bonding with water molecules, an increase in dispersible isopropyl groups interacting with alcohol alkyl groups, and enhanced selective adsorption capacity of TPU-PNIPAM towards alcohol/water mixed solutions. Moreover, TPU-PNIPAM exhibited a characteristic fast-slow-fast-equilibrium ad-sorption curve for different initial concentrations of alcohol/water mixtures, and its selective adsorption capacity increased when temperature reached 55℃. In addition to these general trends, under identical conditions, the selective adsorption capacity of TPU-PNIPAM gradually increased by methanol < ethanol < isopropyl alcohol < propyl alcohol, thus indicating a positive correlation between selectivity performance and hydrophobicity level.

Aluminum (Al) and manganese (Mn) toxicity are the top two constraints to crop production in acid soil. Crops have evolved common and specific mechanisms to tolerate the two stresses. In the present study, the responses (toxicity and tolerance) of wheat near-isogenic lines (ET8 and ES8) and their parents (Carazinho and Egret) to Al and Mn were compared by determining physiolog-ical parameters and transcriptome profiling of roots. The results showed that: (1) Carazinho and ET8 exhibited dual tolerance to Al and Mn as compared with Egret and ES8, indicated by higher relative root elongation and SPAD; (2) After entering into roots, Al was mainly distributed in the root and fixed in the cell wall, while Mn was mainly distributed in the cell sap and then trans-ported to leaves. Both Al and Mn stresses decreased the contents of Ca, Mg, and Zn; Mn stress al-so inhibited the accumulation of Fe, while Al showed an opposite effect; (3) Transcriptomic analy-sis identified 5581 differentially expressed genes (DEGs) under Al stress and 4165 DEGs under Mn stress. Among these, 2774 DEGs were regulated by both Al and Mn stresses, while 2280 and 1957 DEGs were exclusively regulated by Al and Mn stress, respectively. GO and KEGG analyses indi-cated that cell wall metabolism responds exclusively to Al, while nicotianamine synthesis exclu-sively responds to Mn. Pathways such as signaling, phenylpropanoid metabolism, and metal ion transport showed commonality and specificity to Al and Mn. TFs, such as MYB, WRKY, and AP2 families, were also regulated by Al and Mn, and WGCNA identified PODP7, VATB2, and ABCC3 as the hub genes for Al tolerance and NAS for Mn tolerance. The identified genes and pathways can be used as targets for pyramiding genes and breeding multi-tolerant varieties.

Recent years have seen dramatic growth in the number of scholarly scientific works dedicated to the topic of Artificial Intelligence (AI), banking, and finance. With the development of scientometric tools, it is now possible to map, visualize, analyze, and assess scientific activities in many fields of engineering and social sciences including Islamic banking and finance. Based on data retrieved from the Scopus database and using a qualitative method, this study investigates, evaluates, and identifies significant development, trends, and players in the application of AI in Islamic banking and finance using the Visualization Of Similarities Method (VOS) between objects in VOSviewer. From 2006 to 2022, 387 documents were retrieved from the Scopus database; Results revealed that the top five most active countries in terms of publications are Malaysia (117 documents), Indonesia (89 documents), the United Kingdom (36 documents), the USA (24 documents), and Saudi Arabia and Bahrain (24 documents each). The International Islamic University Malaysia and Universitas Indonesia came out on top of active institutions while the top funding source came from the Ministry of Higher Education, Malaysia. The comprehensive findings and analysis reported in this study serve as a roadmap for future academics to create theory and practice for applying AI in Islamic banking and finance.

Bauxite residue (BR), also known as red mud, is a by-product of the production of alumina via the Bayer process. Because of the high sodium oxide and other impurities content, this material is not used to obtain iron or other iron-containing products. In this paper, the hydro-chemical conversion of goethite (FeOOH) to magnetite (Fe3O4) in high-iron BR from the Friguia alumina refinery (Guinea) by Fe2+ ions in highly concentrated alkaline media was studied. The simultaneous extraction of Al and Na made it possible to obtain a product containing more than 96% Fe3O4. The results show that the magnetization of Al-goethite and Al-hemetite accelerates the dissolution of the Al from the iron mineral solid matrix and from the desilication product (DSP). After ferrous sulfate (FeSO4·7H2O) was added directly at the FeO:Fe2O3 molar ratio of 1:1 at 120 °C for 150 min in the solution with the 360 g L-1 Na2O concentration, the alumina extraction ratio reached 96.27% for the coarse bauxite residue size fraction (Sands) and 87.06% for fine BR obtained from red mud. The grade of iron (total iron in the form of iron element) in the residue can be increased to 69.55% for Sands and 58.31% for BR. The solid residues obtained after leaching were studied by XRD, XRF, TG-DTA, VSM, Mössbauer spectroscopy and SEM to evaluate the conversion and leaching mechanisms and the recovery ratio of Al from different minerals. The iron-rich residues can be used in the steel industry or as a pigment.

Training supervised machine learning models requires labeled examples. A judicious choice of examples is helpful when there is a significant cost associated with assigning labels. This article improves upon a promising extant method – Batch-mode Expected Model Change Maximization (B-EMCM) method – for selecting examples to be labeled for regression problems. Specifically, it develops and evaluates alternate strategies for adaptively selecting batch size in B-EMCM. By determining the cumulative error that occurs from the estimation of the stochastic gradient descent, a stop criteria for each iteration of the batch can be specified to ensure that selected candidates are the most beneficial to model learning. This new methodology is compared to B-EMCM via mean absolute error and root mean square error over ten iterations benchmarked against machine learning data sets. Using multiple data sets and metrics across all methods, one variation of AB-EMCM, the max bound of the accumulated error (AB-EMCM Max), showed the best results for an adaptive batch approach. It achieved better root mean squared error (RMSE) and mean absolute error (MAE) than the other adaptive and non-adaptive batch methods while reaching the result in nearly the same number of iterations as the non-adaptive batch methods.

This paper reports on the fabrication of alumina doped preforms using MCVD-vapor phase chelate delivery system with Al(acac)3 as the precursor. The objectives of the work are to study the deposition process, the efficiency of the fabrication process, and the quality of the fabricated fiber preforms. Two parameters are studied, Al(acac)3 sublimator temperature (TAl°C) and deposition direction (i.e. downstream and upstream). Other parameters such as oxygen flow and deposition temperature are fixed. The results showed that a high uniformity of refractive index difference (%RSD &lt; 2%) and core size (%RSD &lt; 2.4%) was obtained along the preform length using downstream deposition while for the combined upstream and downstream deposition the uniformity was deteriorated. The process efficiency was found to be about 21% for TAl°C of 185°C and downstream deposition. From the EDX elemental analysis, the refractive index was found to increase by 0.0025 per mole percent of alumina.

Recently, the environment is being put under constantly increasing pressure. Globally, water shortage is considered as one of the most serious environmental problems which affect human life and plant wealth. Iraq is highly affected by water deficit in many regions. In particular, Al-Najaf region is selected to be under evaluation for the current and future water resources shortage. This study is based on the collected data for rainfall, evaporation, flow-rate, groundwater, water needed for irrigation, and daily uses for the period between 2000 and 2018. The Artificial Neural Network, normal distribution, and lognormal distribution type III are applied for analyzing the collected data in addition to predict the water shortage for year 2050. Results show a water shortage in years 2002, 2004, 2005, and 2017 only for the selected period. A Simulink model is constructed using Matlab to increase the credibility of the estimated results and gives accurate results for the groundwater and surface water needed. Where in 2050, it is found that it needs to use the groundwater source by 0.024 x 10⁹ m³ to support the surface water source which is represented by the Euphrates River. The study shows the extent of inefficient management of water resources in Al-Najaf region.

The R23Cu7Mg4 (R = Ca, Eu) intermetallics, studied by single crystal X-ray diffraction, were found to be isostructural with the Yb23Cu7Mg4 prototype (hP68, k4h2fca, space group P63/mmc), forming a small group inside the bigger 23:7:4 family, otherwise adopting the hP68-Pr23Ir7Mg4 crystal structure. The observed structural peculiarity is connected with the divalent character of the R component and with a noticeable volume contraction, resulting in a clear clustering of title compounds inside the whole 23:7:4 family. The occurrence of fragments typical of similar compounds, particularly Cu-centered trigonal prisms and Mg-centered core-shell polyicosahedral clusters with R at vertices, induced the search of significant structural relationships. In this work, a description of the hexagonal crystal structure of the studied compounds is proposed as a linear intergrowth along the c-direction of the two types of slabs R10CuMg3 (parent type: hP28-kh2ca, SG 194) and R13Cu6Mg (parent type: hR60-b6a2, SG 160). The ratio of these slabs in the studied structure is 2:2 per unit cell, corresponding to the simple equation 2XR10CuMg3 + 2XR13Cu6Mg = 2XR23Cu7Mg4. This description assimilates the studied compounds to the (Ca,Eu,Yb)4CuMg ones, where the same slabs (of p3m1 layer symmetry) are stacked in a different way/ratio, and constitutes a further step towards a structural generalization of R-rich ternary intermetallics.

There has been controversy around the mechanical properties of Mg-alloys such as AZ91D and the large variation of these have been seen. The current paper addresses this controversy through specially fabricated samples combined with tensile testing and advanced metallography, including 3D reconstruction of the phases. The results show that despite a more brittle nature of the fracture, the equiaxed microstructure displays a better elongation as compared to a dendritic microstructure. The main conclusion is that this is primarily caused by the nature, or tortuosity, of the Mg17Al12-network in the material.

Understanding of the decisive role of the interaction mechanism and kinetics in the combustion processes is highly relevant for the elaboration of optimal conditions for obtaining Mo-Cu composite powders. From this perspective, the efficient delivery of the reduction mechanism of copper and molybdenum oxides with combined Mg + C reducing agents at high heating rates is crucial to develop a valuable approach for the combustion synthesis of Mo-Cu composite powders. Herein, we shed light on the mechanism of the reactions in all the studied binary, ternary and quaternary systems contemporaneously demonstrating the effect of the heating rate on the conversion degree. The combination of two highly exothermic and speedy reactions (MoO3+3Mg and CuO+Mg vs MoO3+CuO+4Mg) led to a slow interaction with weak self-heating (dysynergistic effect) due to a change in the reaction mechanism. On the other hand, it has been shown that during the simultaneous utilization of the Mg and C reducing agents, the process begins exclusively with carbothermic reduction, and at relatively high temperatures it continues with magnesiothermic one. The effective activation energy values of the magnesiothermic stages of the studied reactions were determined by Kissinger isoconversional method.

The article focuses on the galvanic replacement synthesis of Ti-Ni and Zr-Ni metal systems with the "core-shell" structure which are potential precursors for intermetallics. The authors defined the effective synthesis parameters and the formation features of polymetallic systems character-ized by granulometric, phase and elemental composition. The X-ray fluorescence and X-ray phase analysis methods showed that the deposition of nickel on dispersed titanium and zirconium leads to the production of test samples with phase composition representing a mechanical mixture of Ni and Ti, Ni and Zr. The method of X-ray fluorescence analysis showed that the presence of hy-drofluoric acid with a 0.5-1.5 M concentration results in the formation of fixed quantitative ratios of elements in the precipitate, which allows the quantitative composition of dispersed systems "titanium - nickel", "zirconium - nickel" to be regulated within a relatively wide range. Scanning electron microscopy proved that all synthesized systems are characterized by a highly porous structure that follows the titanium and zirconium particle surface contour and the presence of spherical nanoscale subunits on the formed particle surface.

In this work, a ZIF-67/MWCNTs/Nafion sensor platform was constructed based on the good adsorption capacity of ZIF-67, the electrical conductivity of multiwalled carbon nanotubes (MWCNTs) and the excellent chemical stability of Nafion for the detection of Cu2+ in water. Meanwhile, the modified materials were characterized by scanning electron microscopy (SEM), Transmission electron microscopy (TEM), BET specific surface area test, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and Fourier transform infrared spectrometry (FT-IR). Cyclic voltammetry (CV), electrochemical impedance (EIS), and square wave solvation voltammetry (SWSV) electrochemical methods were used to perform applied test studies on ZIF-67/MWCNTs/Nafion/GCE. The results show that ZIF-67/MWCNTs/Nafion/GCE has high sensitivity (57.5 μA/μM) and a low limit of detection (15.0 nM) for the electrochemical detection of Cu2+ ions in an electrochemical sensing system. It has high adsorption selectivity for Cu2+, and the recovery of Cu2+ in real water reached 98.6%-103%. The modified electrode has good repeatability, reproducibility, anti-interference, and stability, which makes this sensing platform can be practically applied to the detection of domestic water.

Among the thermophysical properties, the surface / interfacial tension, viscosity and density / molar volume of liquid alloys are the key properties for the modelling of microstructural evolution during solidification. Therefore, only reliable input data can yield accurate predictions preventing the error propagation in numerical simulations of solidification related processes. Due to experimental difficulties related to reactivity of metallic melts at high temperatures, the measured data are often unreliable or even lacking. The application of containerless processing techniques either leads to a significant improvement of the accuracy or makes the measurement possible at all. On the other side, accurate model predicted property values could be used to compensate the missing data; otherwise, the experimental data are useful for the validation of theoretical models. The choice of models is particularly important for the surface, transport and structural properties of liquid alloys representing the two limiting cases of mixing, i.e. ordered and phase separating alloy systems. To this aim, the thermophysical properties of the Fe-Si and Cu-Pb systems were analysed and the connections with the peculiarities of their mixing behaviours are highlighted.

The contact materials in high-voltage vacuum interrupter require properties such as high conductivity, high density, and high hardness to minimize arc heat damage. In this study, copper–molybdenum-chromium alloys contact materials are examined for a high voltage contact material. Ball milling process was carried out after analyzing the raw materials of copper, chromium, and molybdenum powders. A green compact was produced using a high press with the mixed powder. Afterwards, composite was produced by sintering method according to temperature and infiltration method according to Cu content in green compact. The composite of sintering method showed a density of 8.55 g/cm3 (relative density 93%) a hardness of 217 HV, and an electrical conductivity of 40.7 IACS% at 1200 °C. The composite of 10 wt.% Cu produced by the Cu infiltration method showed a density of 8.7 g/cm3 (relative density 94%), Hardness of 274HV and electrical conductivity of 39 IACS% at 1300 °C. The measurements of physical properties showed the new possibility of using the Cu–Cr–Mo alloy as a contact material for high-voltage vacuum interrupters.

Li₂TiO₃ nanopowders were synthesized by hydrothermal process using anatase TiO₂ and LiOH H₂O as raw materials. Li₂TiO₃ crystallizes in the layered monoclinic structure (space group C2/c) with average crystallite size of 34 nm. Morphology, elemental composition and local structure of products were carried out using HRTEM, FESEM, EDS, Raman and FTIR spectroscopy. Transport properties investigated by d.c. (4-probe measurements) and a.c. (complex impedance spectroscopy) show the activation energy of 0.71 and 0.65 eV, respectively. The ionic transport properties of Li⁺ ions in nanocrystalline Li₂TiO₃ characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) validate the good electrochemical properties of this anode material for lithium-ion batteries.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

High temperature titanium alloys are widely used in aerospace hot parts, however, the thermal barrier temperature of 600 oC limits its service temperature. In this paper, a two-step hot-dip plating method is proposed to prepare the composite coating containing Ce on the surface of titanium alloy, which can make the oxidation resistance temperature of titanium alloy reach 800 oC The microstructure, phase composition and element distribution of Ce-containing Ti-Al-Si hot-dip coating, Ce-containing Ti-Al-Si pre-oxidation coating and Ce-containing Ti-Al-Si high-temperature oxidation coating were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The results show that the Ti-Al-Si hot-dip coating containing Ce is mainly composed of (Ti,Ce)(Al,Si)3 alloy phase layer, and the Ti-Al-Si pre-oxidation coating containing Ce is mainly composed of Ti-Al binary system phase layer and dense Al2O3 layer rich in CeO2. Ce in the high temperature oxidation coating of Ti-Al-Si containing Ce is mainly distributed in Ti3Al, TiAl, TiAl3+Ti5Si3 mixed phase layer and Al2O3. The addition of Ce can promote the formation of continuous Al2O3 layer, improve the uniformity of composite coating, prevent the spread of cracks, and improve the high temperature oxidation resistance of Ti-Al-Si coating.

The interference-fit size has a significant effect on CFRP/Al-alloy laminates riveted lap joints, the requirements for the interference-fit size are different because of the strengthening of heterogeneous materials. However, in the process of the riveted CFRP/Al-alloy, the heterogeneous laminates lead to poor structural strength because of the different requirements of interference-fit size. Therefore, the different assembly types of riveting mold are designed to acquire a novel interference-fit size, and the tensile test is adopted to evaluate the tensile property. In addition, the fracture failure of CFRP/Al-alloy laminates riveted lap joint is observed by the ultra-depth of field microscope. Finally, the best assembly type is the trapezoid riveting mold combined with an arc riveting die, and the sidewall intersection angle of the trapezoid riveting mold is 66° which could achieve a suitable interference-fit size and a better mechanical performance.