Titanium alloys belong to the metal biomaterials that are one of the most widely used in medicine. In recent years, in order to reduce the use of vanadium, Ti6Al4V alloy is increasingly replaced by Ti6Al7Nb alloy. In addition, to ensure the best possible biocompatibility, its surface is subjected to appropriate modifications, for example, anodic oxidation. Despite the extensive use of anodic oxidation of titanium implants in orthopedics, there are few works focused on a detailed analysis of the chemical composition of the surface layers. In addition, the effect of treatments before anodic oxidation on the properties of the produced layer has not been analyzed. Thus, the purpose of this study was to analyze in detail the chemical composition of the passive layer of Ti6Al7Nb alloy obtained by anodic oxidation preceded by sandblasting. Moreover, the physicochemical properties of the analyzed surface affecting biocompatibility were determined. For this purpose, surface observation, wettability and roughness tests, microhardness tests, electrochemical tests and phase composition analysis were carried out. In addition, the preclinical suitability, of the surface modified in this way, was evaluated by cytotoxicity tests.

New metastable β titanium alloys are receiving increasing attention due to their excellent biomechanical properties and machinability is critical to their uptake. In this study machining chip microstructure have been investigated to gain an understanding of strain and temperature fields during cutting. For higher cutting speeds, ≥60 m/min, the chips have segmented morphologies characterised by a serrated appearance. High levels of strain in the primary shear zone promote formation of expanded shear band regions between segments which exhibit intensive refinement of the β phase down to grain sizes below 100 nm. The presence of both α and β phases across the expanded shear band suggests that temperatures during cutting are in the range of 400–600 °C. For the secondary shear zone, very large strains at the cutting interface result in heavily refined and approximately equiaxed nanocrystalline β grains with sizes around 20–50 nm, while further from the interface the β grains become highly elongated in the shear direction. An absence of the α phase in the region immediately adjacent to the cutting interface indicates recrystallization during cutting and temperatures in excess of the 720 °C β transus temperature.

Titanium alloys are difficult to machine and have poor tribological properties. This paper investigates the lubricating performance of γ-Al2O3/ZnO hybrid nanofluids for Ti-6Al-4V. The pure and hybrid nanofluid are compared, and the effects of γ-Al2O3/ZnO ratios are studied. The results show that γ-Al2O3/ZnO hybrid nanofluids outperform pure nanofluid in terms of lower friction coefficients and better surface quality. Moreover, the hybrid nanofluid with a mass ratio of Al2O3 to ZnO of 2:1 demonstrates the best lubrication performance with a reduced friction coefficient of up to 22.1% compared to the base solution, resulting in improved surface quality. Al2O3 nanoparticles can adhere to the surface of ZnO nanoparticles and work as a coating, which further enhances the lubrication performance of the water-based nanofluid.

At present, in the field of aviation industry, titanium alloy is mainly used to manufacture parts such as compressor disc, blade and casing of aircraft engine. When working, titanium alloy parts produce high temperature due to high-speed running friction, which makes the high temperature oxidation resistance and friction resistance of titanium alloy greatly reduced. When their working environment contains salt, titanium alloys are subjected to thermal corrosion, which limits their wider practical applications. This paper introduce the aluminide coating and its preparation methods. The characteristics and functional mechanism of three functional coatings for service environment, such as high temperature resistant alumina-based coating, thermal corrosion resistant alumina-based coating and wear-resistant alumina-based coating are summarized. Finally, the development direction of composite coatings of titanium and titanium alloys for complex service environment is prospected.

Outer particles collision with certain dynamic object is not a pure impact wear behavior; it is typically accompanied by sliding wear phenomena. This study aimed investigating the impact-sliding wear performance of three different TC17 titanium alloys. One was untreated, and the other two were subjected to laser shock peening (LSP) by 5 and 7 J pulse energy, respectively. Wear test was performed on a novel impact-sliding wear testing rig, which can realize multiple impact-sliding motions by changing motion parameters in x and z directions. Present results showed that wear resistance of both treated samples improved compared with the untreated alloy. Given the increase in wear cycles, increment in wear rate of the untreated sample was constantly higher than those of treated samples. All results can be attributed to the increase in surface hardness of the material and residual compressive stress, which was also introduced after LSP.

The fracture strength was compared in a scratch test of coatings based on the ZrN system with the introduction of Ti, Nb and Hf, which were deposited on a titanium alloy substrate. The coatings were deposited using Controlled Accelerated Arc (CAA-PVD) technology. The comparison was carried out according to two parameters: adhesion strength to the substrate and overall coating strength. The (Zr,Hf)N coating showed better resistance to destruction, but had worse adhesion to the substrate. As a result, although the coating is retained directly in the scribing groove, a large area of delamination and destruction is formed around the groove. The (Ti,Zr,Nb)N coating, with its somewhat lower strength, has high adhesion to the substrate; no noticeable delamination is observed along the groove boundary.

Surface treatments of metals based on laser marking technology is an important application in a wide range of industrial fields. By specific combinations of laser processing parameters, the modified surface leads to different textures with specific roughness and colored appearance. Most of current works are focused on the modification of color tonality of flat surfaces, or the development of specific topography features, but the combination of both processes is not usually evaluated, mainly due to the complexity to control the optical properties on rough surfaces. This research presents an analysis of the influence of the micro-geometrical characteristics of periodic patterned laser tracks on the chromaticity and reflectance of Ti6Al4V substrates. The samples were irradiated with an infrared nanosecond pulsed laser under air atmosphere, taking as control parameter the scan speed of the beam. A roughness evaluation, microscopic inspection, absorption and chromaticity examination were conducted. Although micro-crack growth was detected in isolated case (10 mm/s), the possibility of adjusting the result color were demonstrated by controlling the thermal affected zone thickness of the textures. Results of rough/colored combined textures allow opening new perspectives in industrial design, particularly in aesthetic applications with special properties.

The mechanical behavior, microstructures as well as the crystallographic textures of the Ti57-Nb43 alloy were investigated on cylindrical specimens compressed at high temperatures, in the range of 700-1000 °C, and strain rates between 0.001 and 1.0 s-1. Hardening, followed by softening behaviours were observed as a function of strain, due to the occurrence of dynamic recrystallization/recovery in hot deformation. The modified five-parameter Voce type equation described well the stress-strain curves, but for the present alloy, it was also possible with only four parameters. A new two-variables polynomial function was employed on the four parameters that described well the flow curves as a direct function of temperature and strain rate. It permitted to reduce the number of parameters and had the predictive capacity for the flow stress at any temperature, strain, and strain rate in the investigated range. The crystallographic textures were similar at all temperatures with an increase of intensity from 900 °C. The textures could be characterized by a double <100> and <111> fiber and a unique component of (001)<110>, the latter inherited from the initial hot rolling texture. Viscoplastic polycrystal self-consistent deformation modeling reproduced the measured textures showing that dynamic recrystallization did not alter the development of the deformation texture, only increased it intensity.

The effect of low cycle fatigue (LCF) pre-damage on the subsequent very high cycle fatigue (VHCF) behavior is investigated in TC21 titanium alloy. LCF pre-damage is applied under 1.8% strain amplitude up to various fractions of the expected life and subsequent VHCF properties are determined using ultrasonic fatigue tests. Results show that 5% of LCF pre-damage insignificantly affects the VHCF limit due to the absent of pre-crack, but decreases the subsequent fatigue crack initiation life estimated by Pairs’ law. Pre-cracks introduced by 10% and 20% of LCF pre-damage significantly reduce the subsequent VHCF limits. The crack initiation site shifts from subsurface-induced fracture for undamaged and 5% of LCF pre-damage specimens to surface pre-crack for 10% and 20% of LCF pre-damage specimens in very high cycle region. The fracture mechanism analysis indicate that LCF pre-crack will re-start to propagate under subsequently low stress amplitude when stress intensity factor of pre-crack is larger than its threshold. Furthermore, the predicted fatigue limits based on EI Haddad model for the LCF pre-damage specimens well agree with the experimental results.

One of the modern methods of improving operating characteristics of titanium and titanium-based alloys under conditions of friction and increased contact loads is the method of ion-plasma nitriding. The effect of nitriding of VT5 alloy (Al 4,5-6,7 %, V to 1,2 %, Mo to 0,8 % − analogue 3.7115) in the plasma of a glow discharge excited in a hollow cathode on its tribological characteristics in pairs with different materials in T-1 fuel and under dry friction conditions has been studied. For research and tribological tests, samples of VT5 alloy were nitrided in the plasma of a glow discharge excited in a hollow cathode at a temperature of 975 ± 15°C and a pressure of 58 ± 2 PA in a nitrogen-argon gas mixture with a nitrogen content of 78 %. Studies of samples of VT5 alloy after nitriding showed that the surface roughness Ra was in the range of 0.58-0.64, and the surface hardness HV5 was 525 ± 20 kgf/mm² at a base hardness of 325 ± 15 kgf/mm². Tribological tests were performed on a friction machine 2070 SMT-1 according to the scheme "cube - roller". Tests under conditions of friction with oil were performed at a load of 200 N. The sliding speed during the tests was 1.3 m/s, the test time was 75 sec. The test under dry friction conditions was carried out at a load of 100 N and a sliding speed of 0.785 m/s, the test time was 30 minutes. Low wear ability in relation to the nitrided titanium alloy VT5 (<2.4x10^-4 mm³/s), as well as friction coefficients at the level of 0.08 to 0.12 in the order of their growth had bronze VB-23NTS (Pd 18–22 %, Ni 3–4 %, Zn 3–4 %, Sb 3–4 %, P 0.15–0.3) r.O10C2N3, VB-24 (Sb 4.7–6, 2 %, P 0.4–0.9), steel 1.3505, cast iron GGG80, cemented steel 20Cr3MoWV.

: TiAl6V4 alloy is widely used in selective laser melting and direct laser melting. In turn, works devoted to the issue of how the track stacking scheme affects the value of mechanical properties is not enough. The influence of the Ti6Al4V alloy track trajectories on the microstructure and mechanical properties during direct laser deposition is studied in this article for the first time. The results were obtained on the influence of «parallel» and «perpendicular» technique of laying tracks in direct laser synthesis. All studied samples have a microstructure typical of the hardened two-phase condition titanium. It is shown that the method of laying tracks and the direction of load application during compression testing relative to the location of the tracks leads to a change in the ultimate strength of the Ti-6Al-4V alloy from 1794 to 1910 MPa. The plasticity of the Ti-6Al-4V alloy obtained by direct laser alloying can vary from 21.3 to 33.0% depending on the direction of laying the tracks and the direction of the compression test. The hardness of alloys varies in the range from 409 to 511 HV and depends on the method of laying the tracks and the direction of hardness measurements.

The corrosion behavior of the TiTaNbZrAg alloys with different amounts of Tantalum (0 %, 10 % and 20%) and with distinct surface topography (smooth and rough) was investigated in phosphate buffer solution (PBS) for long-time immersion (1000 hours). The corrosion resistance was studied by Open circuit potential (OCP), potentiodynamic polarization (PP) and electrochemical impedance spectroscopy (EIS). From the potentiodynamic investigations, it was observed that all types of samples show good corrosion resistance (i.e. Rcorr < 10µm y-1) and may be used successfully for medical applications. However, the samples with smooth surface and with a certain amount of Ta (10 % and 20%) exhibit the best corrosion performance (Rcorr < 1µm y-1). As regard the samples with rough surface, the results evidenced that they show lower corrosion resistance (1< Rcorr < 3 µm y-1), suggesting that the Ta presence not necessary brings about a very good corrosion protection. Actually, the synergetic effect of both the presence of Ta and surface roughness plays an important role in corrosion behavior. Based on literature reports, we assume that the good corrosion resistance results from the good stability of the film, formed mainly from Ta2O5 and TiO2, formed on the alloy surface during immersion in PBS.

Directed energy deposition (DED) parameters were determined for near-β alloy Ti-55511 by employing statistical design of experiments (DOE) methods. Parameters resulting in fully dense freeform deposits were identified using two sequential DOEs. Single laser tracks were printed with several laser power, traverse rate, and powder feed rate settings in an initial DOE to identify promising build parameters. Capture efficiency and effective deposition rate were used to characterize and rank the single track deposits. The best parameters were then used to print solid cube with various X-Y and Z-overlaps (different hatch spacing, HS, and layer thickness, ZS) in a second DOE. Suitable deposition parameters were selected based on cube density and microstructure and were used to fabricate larger tensile samples for mechanical testing. Multiple parameter sets were found to provide dense Ti-55511 deposits with acceptable mechanical properties and parametric models showed statistical significance.

The microstructure evolution, superplasticity, and room temperature mechanical properties of Ti-4%Al-1%V-3%Mo alloys modified with 0.01-2 wt.% boron were investigated. Increasing the boron content from 0 to 0.1 wt.% effectively refined prior β-grains, reducing a mean grain size from ~700 µm to ~210 µm. Whiskers of the TiB phase with a size in a range of 0.7-2.9 µm were observed after solidification and thermomechanical processing. Alloys with 0.01-0.1 wt.% boron exhibited similar superplastic elongations and strain rate sensitivity coefficient m of 0.4-0.5 at a strain rate of 1×10-3 s-1 and the elongation to failure decreased from 1000% at 875°С to 400-500% at 700°С. Along with this, the minor boron addition effectively decreased flow stress values, especially at 775 °C, that was explained by the acceleration of the recrystallization and globularization of the microstructure at the initial stage of deformation. Recrystallization-induced decrease in yield strength from 770 MPa to 680 MPa was observed with an increase in boron content from 0 to 0.1 wt.%. Heat treatment increased post-forming strength characteristics for the alloys with 0.01-0.1 wt.% boron by 90–140 MPa without ductility reduction. Alloys with 1-2 wt.% B demonstrated the opposite behavior. The grain refinement effect was not revealed, and prior β grain sizes were ~670-750 µm after solidification. Thermomechanical processing promoted the fragmentation of boride whiskers and the formation of near-spherical particles with a size of ~1 μm for the alloy with a eutectic concentration of 2 wt.% B. A high fraction of borides, ~5-11%, in the alloys with 1-2 wt.% B deteriorated the superplastic properties and drastically decreased ductility at room temperature. The alloy with 2 wt.% B demonstrated non-superplastic behavior and a low level of mechanical properties, meanwhile, the alloy with 1% boron exhibited high-temperature superplasticity at 875 °C with elongation of ~500%, and yield strength of 830 MPa, ultimate tensile strength of 1020 MPa at a room temperature after 100% of superplastic deformation.

Advanced manufacturing techniques, aimed at implants with high dependability, flexibility, and low manufacturing costs, are crucial in meeting the growing demand for high-quality products like biomedical implants. Incremental sheet forming is a promising flexible manufacturing approach for rapidly prototyping sheet metal components using low-cost tools. Titanium and its alloys are used to shape most biomedical implants because of its superior mechanical qualities, biocompatibility, low weight, and great structural strength. The poor formability of titanium sheets at room temperature, however, limits their widespread use. The goal of this research is to show that gradual sheet formation of a titanium biomedical implant is possible. The possibility of creative and cost-effective concepts for the manufacturing of such complicated shapes with significant wall angles is explored in this study. A numerical simulation based on finite element modeling as well as a design process tailored to metal forming is used to complete the development. The mean of uniaxial tensile tests with a constant strain rate was used to study the flow behavior of the studied material. To forecast the crack, the obtained flow behavior was modeled using the behavior model and failure model.

Ti-6Al-4V (TC4) titanium alloy parts were successfully fabricated by laser melting deposition (LMD)technology in this study. Proper normalizing temperatures were presented in detailed for bulk LMD specimens. Optical microscope, scanning electron microscopy, X-ray diffraction and electronic universal testing machine were used to characterize the microstructures, phase compositions, the tensile properties and hardness of the TC4 alloy parts treated using different normalizing temperature. The experimental results showed that the as-fabricated LMD speceimens microstructures mainly consisted of α-Ti phase with a small amount of β-Ti phase. After normalizing treatment, in the area of α-Ti phase, the recrystallized length and width of α-Ti phase both increased. When normalizing in the (α+β) phase field, the elongated primary α-Ti phase in the as-deposited state was truncated due to the precipitation of β-Ti phase and became a short rod-like primary α-Ti phase. In as-fabricated microstructure, the β-Ti phase was precipitated between different short rod-shaped α-Ti phases distributed as basketweave. After normalizing treatment at 990 for two hours with subsequent air cooling, the TC4 titanium alloy had significant different microstructures from original sample produced by LMD. Moreover, the mismatch of tensile and hardness property was mitigated in this heat treatment. So the normalizing treatment methods and temperature can be qualified as a prospective heat treatment of titanium alloy fabricating by laser melting deposition.

Dispersed silver nanoparticles (AgNPs) on the surface of titanium alloy (Ti6Al4V) and titanium alloy modified by titania nanotube layer (Ti6Al4V/TNT) substrates were produced by chemical vapor deposition method (CVD) using novel precursor of the formula [Ag₅(O₂CC₂F₅)₅(H₂O)₃]. The structure and volatile properties of this compound were determined using single crystal X-ray diffractometry, variable temperature IR spectrophotometry (VT IR), and electron inducted mass spectrometry (EI MS). The morphology and the structure of the produced Ti6Al4V/AgNPs, and Ti6Al4V/TNT/AgNPs composites were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Moreover, measurements of hardness, Young’s modulus, adhesion, and surface free energy have been carried out. The ability to release silver ions from the surface of produced nanocomposite materials immersed in PBS solution has been estimated using inductively coupled plasma mass spectrometry (ICP MS). The wettability and the surface free energy of samples were estimated on the base of contact angle studies with the use of water and diiodomethane. Among the studied surface-modified titanium alloy implants, the best nano-mechanical properties were noticed for the Ti6Al4V/TNT15/AgNPs composite. The location of silver nanoparticles inside of titania nanotubes caused their lowest release rate, which may indicate on suitable properties above mentioned type of the composite for the construction of implants with a long term of antimicrobial activity.

The influence of the hot isostatic pressing (HIP) post-processing step on structural and phase changes, porosity healing and mechanical strength in a powder metallurgy Ti35Nb2Sn alloy was studied. Powders were pressed at room temperature at 750 MPa, and then sintered at 1,350°C in a vacuum for 3 h. The standard HIP process at 1,200°C and 150 MPa for 3 h was performed to study its effect on a Ti35Nb2Sn powder metallurgy alloy. The influence of the HIP process and cold rate on density, microstructure, the quantity of interstitial elements, mechanical strength and Young's modulus was investigated. HIP post-processing for 2 h at 1,200°C and 150 MPa led to greater porosity reduction and a marked retention of the β phase at room temperature. The slow cooling rate during the HIP process affected phase stability, with a large amount of α”-phase precipitate, which decreased the titanium alloy’s yield strength.

The osseointegration process in and around additively manufactured (AM) lattice structures of a new titanium alloy, Ti–19Nb–14Zr, was evaluated. Three different implants, including lattices with increasing high sidewalls gradually closing them, were designed, manufactured and implanted in the tibia and metatarsal bone of two sheep for twelve weeks. After removal, they were characterized with X-ray computed tomography (XCT). The 3D XCT images were segmented using machine learning. The bone-interface implant (BII) and bone-implant contact (BIC) were studied. The results show that, since AM naturally leads to high roughness surface finish, the wettability of the implant is increased. The new alloy possesses an increased affinity to the bone enhancing the quality of osseointegration. The lattice provides crevices, in which the biological tissue can jump in and cling. The combination of these factors is pushing ossification beyond its natural limits. Therefore, the quality and speed of the ossification and osseointegration in and around these Ti–19Nb–14Zr AM laterally closed lattice implants open the possibility of bone spline key of prostheses. This enables the stabilization of the implant into the bone while keeping the possibility of punctual hooks allowing the implant to be removed more easily if required.

The majority of contemporary total hip arthroplasty (THA) implants are constructed from Ti-alloys, which are generally believed to generate fewer adverse local tissue reactions (ALTR) compared to CoCr-alloys. This study presents a case of unusual primary THA failure where a substantial release of Ti-alloy debris was observed. A 52-year-old active male underwent THA after posttraumatic aseptic necrosis of the femoral head in 2006. Seventeen years after the procedure, the patient presented with groin pain and restricted range of motion. X-rays revealed protrusion of the alumina ceramic head through the Ti6Al4V acetabular cup. Trace element analysis indicated significantly elevated levels of serum Ti, Al and V. CT and MRI confirmed Ti-alloy cup failure and severe ALTR. During revision surgery, the worn-out ceramic head was in direct contact with the acetabular cup, having protruded through the central hole it created over time. Histological analysis of tissue samples showed wear-induced synovitis with areas of multinucleated foreign-body giant cells and accumulation of numerous metal particles but no acute inflammatory response. Six months after the revision THA, the patient has experienced favourable outcomes. This case provides an instructive illustration for studying the consequences of substantial release of Ti-alloy debris from orthopaedic implants.

Literature review indicates that the basic microstructure of Ti-6Al-4V is bimodal which consist of two phases: α + β, and it occurs after the fabrication in conventional methods such as casting, plastic forming or machining processes. After the additive manufacturing methods, there could be significant changes in the microstructure. Due to the rapid heat exchange during heat-treatment process, bimodal microstructure transforms into lamellar microstructure which consists of two phases α′ + β. Despite applying optimum printing parameters, 3D-printed products exhibit typical surface defects and discontinuities. Recently, two of the primary technologies for the improvement of surface layer properties of titanium alloys are shot peening and electropolishing. Literature review signalizes that shot peening and electropolishing processes have positive impact on the corrosion behaviour, mechanical properties and the condition of the surface layer of titanium alloy. Furthermore, there is a lack of studies about combining shot peening and electropolishing in one hybrid process on titanium alloys, which could synthesize the benefits of both processes. The scope of future investigation is also included in this review.

Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

Keywords: friction stir processing; additive manufacturing; wire; titanium alloy; material transfer; microstructure; microhardness

This paper presents a new method of preparing a coating on the Ti65 titanium alloy by a two-step procedure comprising hot-dipped aluminum and solid carburization. The effects of the carburization in the presence of NaCl deposit at 810oC have been systematically studied. In this article, the microstructure, morphology, phase composition of the coating, and the corrosion products were investigated by SEM, EDS, and X-ray diffraction. Results indicated that the corrosion resistance of hot dip aluminum/carburizing composite coating was not significantly enhanced by hot dip aluminum coating. This can be attributed to the formation of TiC and Ti3AlC after carburization, which promoted the formation of loose and unprotected TiO2 in the coating during molten salt corrosion. In addition, the oxidation of the carbon atom into CO2 /CO leaded to a high concentration of vacancy in the coating, creating channels for NaCl to penetrate the coating and accelerated the corrosion rate.

Ti-Al alloy phase layer/Ti-Al carburizing composite coating was prepared on the surface of titanium alloy by the stepwise coating method of hot dip aluminization and then carburizing. The weight gain results of the composite coating showed that the titanium alloy coated with the composite coating had long-term stability (≥16 days) at 800oC. The microstructure, phase structure and composition of the composite coating were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS).The composite coating is composed of an alloy phase layer and a carburized layer. The natural transition of four phases (Ti3Al/TiAl/TiAl2/TiAl3) in the alloy phase layer, significantly improves the interfacial bonding between the coating and the substrate, and slows down the propagation of microcracks through the coating.Al2O3, TiC and C in the carburizing layer improve the surface hardness of the coating, and TiAl2 and Al2O3 also have excellent oxidation resistance at high temperature.

The article discusses the main technologies for processing titanium-containing raw materials, and the advantages and disadvantages of various technological solutions. The analysis of the literature review showed that the traditional schemes for the production of titanium products are mainly focused on the use of ilmenite concentrates. In connection with the depletion of ilmenite deposits, in the near future there will inevitably be a need to switch to the use of complex ores - titanomagnetites. The obtaining of titanium dioxide from titanomagnetite raw materials with a high content of impurity components requires an individual approach for each specific deposit. It is proposed to consider the possibilities of further improvement of the development of a technological process for low-temperature (1000-1200 oC) processing of titanomagnetite concentrates with the production of pure titanium dioxide.

1) Background: The objective was to evaluate the corrosion resistance of different commercially pure ultrafine-grained (UFG) titanium and its alloys with acid etched surface processed by equal-channel angular pressing (ECAP); 2) Methods: Coarse-grained and UFG titanium samples were investigated using polarization resistance technique. Surface characteristics of the native oxidized layer were evaluated by TEM and XRD. Electrochemical tests were under physiological electrolyte at a rate of 1 and 10 mV/s. Weight loss tests were performed after immersion into HCl solution for up to 3 years; 3) Results: UFG titanium was less susceptible to corrosion which was identified under lower rates and at higher polarization resistance than its coarse grain counterparts. Titanium Grade 2 and Grade 4 demonstrated similar corrosion susceptibility. Titanium Grade 5 revealed a thin and tightly adhered native oxide layer with adequate corrosion resistance; 4) Conclusions: ECAP process imposed a more compact and adhered oxidized layer. Surface etching techniques delivered a thicker native TiO₂ layer, being both grain refinement and surface etching techniques responsible for the improved corrosion resistance of Titanium samples under physiological environment after 3 years of observation.

This study evaluated the impact of rough, smooth, and very smooth Titanium (Ti) and zirconia (Zr) surfaces on the neutrophil expression of elastase (NE), matrix metalloproteinase (MMP)-8, MMP-9 and extracellular traps (NETs). Ti and Zr disks with a diameter of 10mm and a thickness of 1.5mm were processed using diamond-impregnated polishing burs and paste to generate rough (R; Ra= > 3µm), smooth (S; Ra= ≥1 to 1.5µm) and very smooth (VS; Ra= <0.1µm) surfaces. Peripheral neutrophils from Wistar rats were cultured on these surfaces and the culture supernatants subsequently analyzed for the presence of NE, MMP-8, and MMP-9 by ELISA, while NETs formation was demonstrated immunohistochemically by staining neutrophils with CD16b and DNA with DAPI. Overall, the expression of NE and MMP-8 were significantly higher from neutrophils cultured on both on Ti and Zr rough surfaces compared to the very smooth surface (R>S>VS) after 2h and 4h of culture. The expression of MMP-9 also increased with culture time however no significant surface effects on expression were observed. Similarly, rough Ti and Zr surfaces (R & S) also showed significantly larger NETs formation compared to the very smooth surface (VS) after 4h and 8h culture. Our findings suggest that increasing surface roughness on Ti and Zr triggers higher secretion of NE, MMP-8 and NETs formation.

Abstract The processing of anatase ores by sulfuric acid digestion is well known for its low titanium dissolution yields, which makes the process economically and technically unfeasible. Generally, to enhance the dissolution of titanium from anatase, thermal processes along with acid and/or alkaline leaching are necessary. Few existing works report yields of direct digestion of anatase with sulfuric acid <48%. This study investigated the sulfuric digestion of anatase and yields around 80% were obtained at relatively mild conditions such as temperature at 220°C, sulfuric acid/concentrate ratio of 1:2 and 3 hours of reaction. A comprehensive characterization of anatase ore was also presented.

Titanium-based Metal Matrix Composites (MMCs) manufactured by additive manufacturing offer tremendous lightweighting opportunities. However, processing the high reinforcement contents needed to substantially improve elastic modulus while conserving significant ductility remains a challenge. Ti-TiC MMCs fabricated in this study report fracture strains in tension up to 1.7% for a Young’s modulus of 149 GPa. This fracture strain is 30% higher than previously reported values for Ti-based MMCs produced by Laser Powder Bed Fusion (LPBF) displaying similar Young’s moduli. The heat treatment used after the LPBF process leads to the doubling of the fracture strain due to the conversion of TiCx dendrites into equiaxed TiCx grains. As-built microstructure shows both un-dissolved TiC particles and sub-stoichiometric TiC dendrites resulting from a partial dissolution of TiC particles. Reduction of the C/Ti ratio in TiC during the process results in an increase in the reinforcement content, from a nominal 12 vol% to an effective 21.5 vol%. The variation of the TiC lattice constant with its stoichiometry is measured, and an empirical expression is proposed for its effect on TiC’s Young’s modulus. The lower TiC initial powder size distribution displayed the best mechanical performance.

Maxillofacial fractures are a prevalent occurrence, and the widespread use of miniplates to stabilize and secure these fractures during surgery is common. However, the post-surgical fate of these miniplates remains a subject of contention among surgeons. Some advocate for their removal, while others suggest leaving them in place. This study aims to perform an extensive meta-analysis of pertinent studies to ascertain the destiny of miniplates employed in maxillofacial surgery and discuss the consequences of either their extraction or retention. To execute this meta-analysis, an exhaustive search was conducted across multiple databases, encompassing PubMed, Scopus, and Google Scholar. Keywords such as "titanium miniplates," "screws," "maxillofacial surgery," "complications," and "removal" were utilized to identify pertinent studies. The search was constrained to studies published between 1989 and 2022. The analysis encompassed only studies reporting outcomes related to miniplates in maxillofacial surgery, including complication rates and removal frequencies. Eleven studies conformed to the inclusion criteria and were incorporated into the meta-analysis, encompassing a total of 2240 patients. All the studies had a retrospective design, with the largest study involving 800 patients. The overall complication rate was determined to be 13.3%. The most prevalent reasons for miniplate removal included patient preference, tooth extraction, and infections. The average time span for miniplate removal was 10.7 months, with the most prolonged reported duration being 24 years. These findings imply that immediate removal might not be imperative in the majority of instances. In conclusion, our meta-analysis underscores the necessity of removing miniplates in cases where hardware leads to a variety of complications and physical discomfort. Principal factors driving plate removal included patient requests, tooth extractions, and infections. Ordinarily, plate removal took place within the span of 6 to 12 months, with the mandible being the most frequent site for removal. These findings accentuate the significance of extended monitoring to assess the trajectory of miniplates in maxillofacial surgery and provide valuable insights for future clinical decisions. To validate these conclusions and gain deeper insights into the factors influencing plate removal in maxillofacial surgery, further research with larger participant cohorts and standardized outcome reporting is imperative.

The creep response of commercially pure titanium was investigated in air at 550, 600 and 650°C, to assess the effect of oxidation on the mechanical response. Experiments demonstrated that exposure at high temperature produced a marked reduction of the minimum creep rate under a given applied stress. Microhardness measurements showed that a hardened zone forms in proximity of the surface, due to oxygen penetration into metal. A simplified composite-model was then used to describe the creep response. In this model, the sample consisted of two zones, the hard case, enriched in oxygen, and the soft pure-titanium core, both creeping with similar strain rates. Calculation led to an estimation of the dependence of the minimum creep rate on stress and temperature for the hard high-oxygen zone. The simplified composite-model here presented gave an excellent description of experimental creep data for pure titanium tested in air and also provided a reliable picture of the effect of oxidation on complex Ti-alloys.

The production of high stiffness Ti-based Metal Matrix Composites (Ti-MMCs) displaying significant ductility by additive manufacturing technologies is not yet at the level of conventionally produced Ti-MMCs. This study outlines the production process of stiffness-driven Ti-TiC MMCs displaying a remarkable ductility. The process consists in powder Mechanical Blending, Laser Powder Bed Fusion (LPBF), and a heat treatment. A TiC fraction of more than 20 vol% was formed in-situ through the reaction of titanium with carbon during the LPBF process. The as-built sub-stoichiometric TiC dendrites are converted in equiaxed TiC grains during the heat treatment. The TiC C/Ti ratio was found to be close to 0.5 in as-built conditions, and 0.7 in heat treated conditions, resulting in an effective reinforcement content nearly twice the one expected for stoichiometric TiC, leading to stronger reinforcement. The mechanical analysis revealed a Young’s modulus of up to 149 GPa and total elongations of up to 2.8%. The former represents a 27% improvement compared to commercially pure Titanium and the latter exceeds by 115% reported values for LPBF Ti-MMCs with similar Young’s modulus. It is enabled by the in-situ formation of defect-free TiC reinforcements combined with their globularisation through heat treatment.

In this study, we present a novel method for fabricating semi-transparent electrodes by combining silver nanowires (AgNW) with titanium nitride (TiN) layers, resulting in conductive nano-composite coatings with exceptional electro-mechanical properties. These nano-composites were deposited on cellulose nanopaper (CNP) using a plasma-enhanced pulsed laser deposition (PE-PLD) technique at low temperatures (below 200°C). Repetitive bending tests demonstrate that incorporating AgNW into TiN coatings significantly enhances the microstructure, increasing the electrodes electro-mechanical robustness by up to four orders of magnitude compared to commercial PET/ITO substrates. Furthermore, the optical and electrical conductivities can be optimized by adjusting the AgNW network density and TiN synthesis temperature. Our results also indicate that the nanocomposite electrodes exhibit improved stability in air and superior adhesion compared to bare AgNW coatings. These findings are crucial for advancing bio-compatible flexible electronics and could lead to the development of new wearable and implantable medical devices.

The goal of this research is to determine the optimal microwave-assisted sol-gel synthesis pa-rameters of TiO2 nanoparticles with the achievement of the crystalline TiO2 nanoparticles with the highest specific surface area and the lowest energy band gap. Titanium isopropoxide was used as a precursor to prepare the sol (colloidal solution) of TiO2, isopropanol as a solvent, acetylacetone for complexation, and nitric acid as a catalyst. Four samples of titanium dioxide were synthesized from the prepared colloidal solution in a microwave reactor at a temperature of 150 °C for 30 minutes and at a temperature of 200 °C for 10, 20, and 30 minutes. The phase composition of the prepared samples was determined by X-ray diffraction analysis (XRD) and Fourier-transform infrared spectroscopy (FTIR). Nitrogen adsorption/desorption isotherms were used to determine the spe-cific surface area and pore size distributions by Brunauer-Emmett-Teller (BET) method. The band gap energy values of the TiO2 samples were determined by diffuse reflectance spectroscopy (DRS). CrystallineTiO2 nanoparticles with the highest specific surface area and the lowest energy band gap were obtained for the TiO2 sample synthesized at 200 °C for 10 minutes.

Nano-titanium has excellent corrosion resistance and can be widely used in the field of corrosion resistant coatings. This paper introduces nano-weight titanium modified phenolic resin coatings and their anti-corrosion properties to explore the principle of nano-titanium modification and the mechanism of anti-corrosion to further develop more advanced corrosion resistant coatings. The article uses scanning electron microscopy, Fourier transform infrared spectroscopy, Raman spectroscopy and UV-Vis spectrophotometer to characterise the morphology and structure of the nano-titanium modified phenolic resin coatings and to determine the corrosion resistance properties of the modified phenolic resin coatings. The results show that the 4% nano-titanium modified phenolic resin coating, nano-titanium powder and phenolic resin will maximize the dispersion and combination, and the structure is good; nano-titanium grafted on phenolic resin, the successful preparation of nano-titanium modified phenolic resin; modified nano-titanium added to improve the coating's ability of UV absorption. The corrosion resistance of the coating is much better than that of the unmodified phenolic resin coating.

Ameloblastoma is an aggressive slow growing benign epithelial odontogenic tumor usually associated with an unerupted third molar. In this report, we present the case of a 71-year-old male with a large swelling on the left mandibular region causing a remarkable facial asymmetry. After clinical, radiological, and histopathological examinations the diagnosis of conventional ameloblastoma was made. To avoid probable recurrence our treatment choice was a segmental mandibular resection with the placement of a reconstructive titanium plate to maintain the space for subsequent bone graft.

Biomaterials have assumed a decisive role in modern medicine by enabling significant advancements in medical care practices. These materials are designed to interact with biological systems, offering substantial solutions for various medical needs. In this research, bioceramic materials consisting of a bioactive hydroxyapatite-based matrix with Ti nanoparticles, were processed as promising materials. These bioceramics were obtained using mechanical milling, uniaxial pressing, and sintering as powder processing techniques. This study evaluates the effect of Ti additions on the structural, electrochemical, and mechanical properties of the hydroxyapatite ceramic material. Titanium additions were about 1, 2 and 3 wt%. The experimental results demonstrate that the biocomposite's structure has two hexagonal phases: one corresponding to the hydroxyapatite matrix and the other to the Ti as a reinforced phase. The biomaterials' microstructure is completely fine and homogeneous. The biomaterial reinforced with 1wt. % Ti exhibits the best mechanical behavior. In this context, Electrochemical tests reveal that bio-ceramics can achieve stability through an ion adsorption mechanism when exposed to a physiological electrolyte. Bioceramics, particularly those containing 1%Ti, develop their bioactivity through the formation a high-density hydroxide film during a porous sealing process at potentials around −782.71 mV, with an ionic charge transfer of 0.43x10^-9 A/cm². Finally, this biofilm behaves as a capacitor Cc = 0.18 nF/cm², resulting in lower ionic charge transfer resistance (Rct = 1.526x106 Ω-cm²) at the interface. This mechanism promotes the material’s biocompatibility for bone integration as an implant material.

Due to its intriguing applications across a wide range of industries, nanotechnology is generating a lot of interest globally. Titanium dioxide (TiO2) nanoparticles are one type of nanoparticle (NP) that is commonly utilised in everyday use and can be produced using a variety of physical, chemical, and environmentally friendly techniques. Green synthesis is an economical, environmentally benign, and non-toxic method of synthesising NPs. Under normal circumstances, the application of TiO2 greatly enhanced the plants' shoot length, leaf area, and root dry weight. These growth-promoting factors coincided with elevated proline, soluble sugar, and chlorophyll B levels as well as improved antioxidant enzyme activity. Thus, higher levels of proline and other metabolites played a role in osmo-protection, while increased antioxidant enzyme activities helped to explain the observed decrease in hydrogen peroxide and malondialdehyde contents. Taken together, these factors significantly improved plant growth under salinity. TiO2 nanoparticles have demonstrated efficacy in treating contaminated water and have been shown to positively impact plant physiology, particularly in response to abiotic stresses. However, the reaction to these nanoparticles varies depending on characteristics such as metal species, type, size, shape, dose, duration of exposure, and other variables. One of the most popular nanomaterials in customer goods, agricultural, and energy industries is TiO2 NPs. Therefore, harm to ecosystems and living things will unavoidably result from high demand and widespread usage. Gaining more knowledge about the toxicity of TiO2 NP to living things could help with risk assessments and safe handling procedures for these nanoparticles. The synthesis of titanium oxide, its many uses, the toxicity of titanium dioxide nanoparticles, and their mode of toxicity are all summarised in this paper.

Surface treatment of implants facilitates osseointegration, with nanostructured surfaces exhibiting accelerated peri-implant bone regeneration. This study compared bone-to-implant contact (BIC) in implants with hydroxyapatite (HA), sand-blasted and acid-etched (SLA), and SLA with calcium (Ca)-coated (XPEED®) surfaces. Seventy-five disk-shaped grade 4 Ti specimens divided into three groups were prepared, with 16 implants per group tested in New Zealand white rabbits. Surface characterization was performed using X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), digital microscopy, and a contact angle analyzer. Cell viability, proliferation, and adhesion were assessed using MC3T3-E1 cells. Apatite formation was evaluated using modified simulated body fluid (m-SBF) incubation. After 4 weeks of healing, the outcomes reviewed were BIC, bone area (BA), removal torque tests, and histomorphometric evaluation. Microstructure analysis revealed irregular pores across all groups, with the XPEED group exhibiting a nanostructured Ca-coated surface. Surface characterization showed a crystalline CaTiO3 layer on XPEED surfaces, with evenly distributed Ca penetrating the implants. All surfaces provided excellent environments for cell growth. The XPEED and SLA groups showed significantly higher cell density and viability with superior osseointegration than HA (p &lt; 0.05); XPEED exhibited the highest absorbance values. Thus, XPEED surface treatment improved implant performance, biocompatibility, stability, and osseointegration.

Effects of plastic deformation on the indentation feature of hot-rolled commercial pure titanium alloy were detected using microindentation. It was found that the most deformed sample experienced the largest indentation resistance and had the maximum dislocation density and the indentation size influenced the CP-Ti indentation feature. The Vicker hardness and energy dissipated demonstrated the significant influence of the dislocation motion and size effects on the indentation in the indentation deformation. The linear relation of the energy ratio which is related to the microstructures and the indentation depth ratio was obtained for hcp materials Titanium alloys.

The effect of defects and microstructure on mechanical properties of Ti-6Al-4V welds produced by tungsten inert gas welding, plasma arc welding, electron beam welding and laser beam welding was studied in the present work. The mechanical properties of the different weld types have been evaluated with respect to micro hardness, yield strength, ultimate tensile strength, ductility and fatigue at room temperature and at elevated temperature. Metallographic investigation was carried out to characterize the microstructures of different weld types and fractographic investigation to relate the effect of defects on fatigue performance. Electron and laser beam welding produced welds with finer microstructure, higher tensile ductility and better fatigue performance than tungsten inert gas welding and plasma arc welding. Large pores and pores located close to the specimen surface were found to be most detrimental to fatigue life.

The use of miniplates for stabilizing bones after orthognathic surgeries, has become increasingly popular for their effectiveness in ensuring stability and promoting swift recovery. However, the post-surgical fate of these miniplates remains a subject of contention among surgeons. Some advocate for their removal, while others suggest leaving them in place. The aims of this study, is to evaluate the incidence, causes, and potential risk factors associated with the removal of miniplates in orthognathic surgeries. A comprehensive meta-analysis was conducted by reviewing studies from various databases like PubMed, Google Scholar, Research Gate, Embase, and Scopus, focusing on publications from 1989 to 2023. Ten studies encompassing a total of 1603 patients which conformed to the inclusion criteria were selected and included in the meta-analysis. With M:F ratio range from 4:1 to 109:141. Total number of miniplates inserted was 5595, and total number of miniplates removed were 294 (5.3%). The most common reasons for miniplates removal were, infection was reported in 161 cases (2.9%), followed by miniplates exposure (34 cases, 0.6%) and palpable plates (23 cases 0.4%). Other indications included pain, patient’s preference, and temperature sensitivity. Relatively less common reasons that resulted in miniplates removal include, sinusitis, second surgery and dental pathology. The mean duration of miniplates removal was 5.5 months with the majority of miniplates (56.1%) were removed from the mandible compared to maxilla. In conclusion, this meta-analysis underscores the importance of miniplate removal in cases where hardware causes diverse complications and physical discomfort. The primary reasons for miniplates removal were infections and plates exposure, with the mandible being the most common site for removal. These findings emphasize the need for continued monitoring to assess the fate of miniplates in orthognathic surgery and provide valuable insights for future clinical decision-making.

Magnetron sputtering was used for producing Titanium Vanadium Nitride (TiVN) coatings on a variety of substrates. In this research, we investigate how changing the sputtering power and nitrogen: argon (N2:Ar) gas ratio affects the structural and tribological properties of TiVN coatings. Scanning Electron Microscope (SEM) technique was used to examine TiVN coating surface morphology. Both variants showed a gradual increase in the intensity of the TiVN coating's (111) and (222) peaks. TiVN coating's tribological properties were examined using a pin-on-disc tribometer with varying loads, speeds, and sliding distances. The wear rates of TiVN-coated brass pins were in the range of 2.5×10-4 to 9.14×10-4 mm3/Nm depending on load, sliding distance, and gas ratio variation, when compared to the wear rates of TiVN-coated brass pins deposited at various power, which ranged from 1.76×10-3 to 5.87×10-3 mm3/Nm.

Strontium (Sr) is a trace element in human body that able to promote bone formation and inhibit bone absorption. The conversion coating of strontium phosphate (Sr-P) on the surface of titanium (Ti) can improve its biological properties, and has a wide application prospect in the fields of dentistry and orthopedics. In this present study, Sr-P coatings with SrHPO4 and Sr3(PO4)2 crystals on Ti are prepared by phosphate chemical conversion (PCC) treatment. And the effect of pH on the properties of Sr-P coatings is researched. The results prove that phase composition, morphology and corrosion resistance of coated Ti are different with the pH values in PCC solution. The morphologies of conversion deposition on Ti change from plat-like to cluster-like, and then homogeneous microcrystals, as pH value changed from 2.50 to 3.25. Only discrete SrHPO4 crystals are generating on substrate at lower pH value, while relative stable Sr3(PO4)2 and SrHPO4 crystals are growing and subsequently forming an integrated coating on Ti as pH is higher than 2.50. The corrosion resistance of coated Ti improves comparing with that of bare Ti because of forming Sr-P coatings with Sr3(PO4)2 phase. In addition, it is indicated that the Sr-P coatings can improve the adhesion and differentiation of BMSCs.

Titanium (Ti) and Ti-based alloys are commonly used in dental implants, and surface modifications of dental implants are important for achieving osseointegration (i.e., direct connection between the implant surface and bone). This study investigated the effect of an eco-friendly etching solution—a hydrogen peroxide–sodium bicarbonate mixture—on the surface properties and contact angles of and osteoblast adhesion and proliferation on Ti surfaces. Disk-shaped Ti specimens were prepared using different surface treatments (machining, sandblasting, and sandblasting/acid-etching), and they were immersed in the etching solution and then ultrasonically cleaned. Surface characterization was performed using scanning electron microscopy, digital microscopy, contact angle analysis, and X-ray photoelectron spectroscopy. MG-63 osteoblasts were cultured on the specimens, and their adhesion to the specimen surface and their proliferation were examined using staining and the MTT assay, respectively. Additional etching with the etching solution caused the formation of nano/micro hierarchical structures, increased the surface roughness, and enhanced the hydrophilicity. Osteoblast adhesion and proliferation were found to improve on the modified surfaces. The eco-friendly etching method has the potential to enhance the biological properties of Ti implant surfaces and to thereby improve the dental implant performance.

Food-grade titanium dioxide (E171) contains variable percentages of TiO2 nanoparticles (NPs) posing awareness about its potential effects on human and animal health. Despite many studies, the actual relationship between the physicochemical properties of E171 NPs and their interaction with biological targets is still far from clear. We evaluated the acute toxicity of E171 in invertebrate and vertebrate animals. In the nematode C. elegans, E171 up to 1.0 mg/mL did not affect worm’s viability and lifespan but significantly impaired pharyngeal function, reproduction, and development. We also focused our attention on the fate of E171 after its penetration inside the circulatory tree, investigating whether its intravenous administration to mice could result in an acute over-absorption to filter organs. A significant increase of hepatic Ti concentration and the formation of microgranulomas were observed. Interstitial inflammation and parenchymal modification were found in lung coupled with Ti accumulation, probably due to the propensity of TiO2 NPs to agglomerate, as demonstrated by transmission electron microscopy experiments showing that the incubation of E171 with serum promoted the formation of compact clusters. Overall, these data emphasize, once again, the actual risk for human and animal exposure to E171.

Gold nanoparticles, were deposited in titanium oxide (TiO2) Degussa-P25 with the Photodeposition method in the presence of UV light at different concentrations. It was determined by diffuse reflectance (DF), Scanning electron microscopy (SEM), that the Photodeposition method is effective for the inclusion of gold particles on the surface. The catalyst band gap showed a reduction to 2.9 e.V, as well as it was observed that the gold-doped catalyst shows absorption in the visible light range around 500 to 600 nm. The percentage of deposited gold nanoparticles was determined by energy dispersive spectroscopy (EDS). The experimental data were analyzed using different analytical techniques (UV-Vis spectrophotometry, TOC total organic carbon), with these results a carbon-based mass balance and reaction kinetics were generated using the Langmuir-Hinshelwood (LH-HW) heterogeneous catalysis model. For the estimation of the kinetic constants, the non-linear regression of the Levengerd Marquad algorithm was used, with these results, kinetic models of the degradation of the molecule and the generation and consumption of Organic Intermediate Products (OIP) were generated.

Metallic nanoparticles (NPs), among polymeric NPs, liposomes, micelles, quantum dots, dendrimers, or fullerenes, are becoming more and more important due to their potential use in the novel medical therapies. Titanium dioxide (titanium(IV) oxide, titania, TiO2) is an inorganic compound that owes its recent rise in scientific interest to photoactivity. After the illumination in aqueous media with UV light, TiO2 produces an array of reactive oxygen species (ROS). The capability to produce ROS and thus induce cell death has found application in the photodynamic therapy (PDT) for the treatment of a wide range of maladies, from psoriasis to cancer. Titanium dioxide NPs were studied as photosensitizing agents in the treatment of malignant tumors as well as in photodynamic inactivation of antibiotic-resistant bacteria. Both TiO2 NPs themselves, as well as their composites with other molecules, can be successfully used as photosensitizers in PDT. Moreover, various organic compounds can be grafted on TiO2 NPs, leading to hybrid materials. These nanostructures can reveal increased light absorption allowing their further use in targeted therapy in medicine. In order to improve efficient anticancer therapy, many approaches utilizing titanium dioxide were tested. The most significant studies are discussed in this review.

Abstract: Air-polishing with low abrasiveness powders is fats arising as a valid and mini-invasive instrument for the management of biofilm colonizing dental implants. The reported advantage is the efficient removal of plaque with respect of the titanium integrity. In the present study, we evaluated the in-situ plaque-removal and continual the post-treatment anti-bacterial efficacy of an innovative erythritol/chlorhexidine air-polishing powder and compared it with sodium bicarbonate. Two peri-implantitis-linked biofilm formers strains Staphylococcus aureus and Aggregatibacter actinomycetemcomitans were selected and used to infect titanium disks before and after the air-polishing treatment. Cells number and viability were assayed by colonies forming units (CFUs) count and metabolic-colorimetric (2,3-Bis-(2-Methoxy-4-Nitro-5-Sulfophenyl)-2H-Tetrazolium-5-Carboxanilide) (XTT) assay. Air-polishing performed with either sodium bicarbonate or erythritol/chlorhexidine was effective in reducing bacteria biofilm viability and number onto pre-infected specimens, while erythritol/ chlorhexidine showed a higher post-treatment biofilm re-growth inhibition. Surface analysis via mechanical profilometry failed to show an increase in titanium roughness, regardless of the powder selected.

In this study, a 5vol. % (TiBw+TiCp)/Ti composite pancake with a diameter of 260mm was prepared by casting followed by open die forging in (α+β) phase region. The microstructures of the composite pancake are inhomogeneous, in terms of both matrix microstructure and distribution of reinforcements. The matrix microstructures were gradually refined from the periphery to centre of the pancake. The TiBw and TiCp reinforcements tend to be uniformly distributed in the centre region and. It is suggested that the microstructure difference can be mainly ascribed to the temperature variation from the periphery to the centre. Additionally, tensile testing results showed that the centre region of the composite pancake exhibits higher strength than the peripheral region. The strengthening mechanism and the softening behavior of the composite pancake with temperature is discussed.

Ultra-low radioactive titanium alloy is a promising material for the manufacture of low-background detectors, which are being developed for experiments in astroparticle physics and neutrino astrophysics. Structural titanium is manufactured on an industrial scale from titanium-sponge. The ultra-low-background titanium-sponge can be produced on an industrial scale with a contamination level of less than 1 mBq/kg of uranium and thorium isotopes. The pathways of contaminants during the industrial production of structural titanium have been analyzed. The measurements have been carried out using two methods: inductively coupled plasma spectroscopy (ICP-MS) and gamma-spectroscopy using high-purity germanium detectors (HPGe). It has been shown that the level of contamination with radioactive impurities does not increase during remelting of titanium-sponge and mechanical processing. We examined titanium-alloys samples obtained at different stages of titanium production, namely, an electrode compaction, a vacuum arc remelting with a consumable electrode (VAR), and a cold rolling of titanium-sheets. It has been found out that all studied samples will be a source of uranium and thorium contamination of the final titanium-alloys. It has been established that the only product allowed obtaining ultra-low-background titanium was the VT1-00 which is manufactured without master alloys addition..

BACKGROUND: Manufacturing costs, along with operational performance, are among the major factors determining the selection of the propulsion system for unmanned aerial vehicles (UAVs), especially for aerial targets and cruise missiles. OBJECTIVES: In this paper, the design requirements and operating parameters of small turbofan engines for single-use and reusable UAVs are analysed to introduce alternative materials and technologies for manufacturing their compressor blades, such as sintered titanium, a new generation of aluminium and an alloy based on titanium aluminides. METHODS: To assess the influence of severe plastic deformation (SPD) on the hardening efficiency of the proposed materials, the alloys in the coarse-grained and submicrocrystalline states were studied. Changes in physical and mechanical properties of materials were taken into account. The thermodynamic analysis of the compressor was performed in a finite element analysis system (ANSYS) to determine the impact of gas pressure and temperature on the aerodynamic surfaces of compressor blades of all stages. RESULTS: Based on thermal and structural analysis, the stress and temperature maps on compressor blades and vanes were obtained, taking into account the physical and mechanical properties of advanced materials and technologies of their processing. The safety factors of the components were established based on the assessment of their stress-strength reliability. Thanks to nomograms, the possibility of using the new materials and the technologies was confirmed in view of the permissible operating temperature and safety factors of blades. CONCLUSIONS: The proposed alternative materials and production technologies for the compressor blades and vanes meet the design requirements of the turbofan at lower manufacturing costs.

Biomaterials are the basis for the development of medicine because they allow safe contact with a living organism. The aim of this work was to produce innovative oxide layers with a porous microstructure on the surface of commercially pure titanium Grade 4 (CpTi G4), and to characterize their properties as drug carriers. Anodization of the CpTi G4 subjected to mechanical grinding and electrochemical polishing was carried out in a solution of 1M ethylene glycol with the addition of 40 g of ammonium fluoride at a voltage of 20 V for 2, 18, 24 and 48 hours at room temperature. It was found that the longer anodization time, the greater the number of pores formed on the CpTi G4 surface as revealed by FE-SEM method, and the greater the surface roughness determined in profilometric tests. As the anodizing time increases, the amount of the drug in the form of gentamicin sulfate incorporated into the resulting pores decreases. The most favorable drug release kinetics profile determined by UV-VIS absorption spectroscopy was found for the CpTi G4 anodized for 2 h making them the best choice when it comes to the drug carrier allowing full use of the therapeutic dose of the drug.

Hard coatings like Titanium diboride (TiB2) on silicon substrates are used for interconnects. micro-electro-mechanical devices and metallurgical protective coatings were analyzed based on shallow depths of nanoindentation penetration which involves a change in the nature of the contact from Hertzian to Pyramidal both in loading as well as unloading modes. Features like ductile fracture, linear unloading, and the creation of electrical conduction paths were analyzed. These high-precision features are influenced by the thickness and crystalline nature of the films and are significant for device fabrication.

Peri-implantitis occurs at a significant rate, which is the leading cause of implant failure. The main reason for this unwanted complication is bacterial invasion and biofilm formation. To reduce the incidence of peri-implantitis, we constructed a carboxymethyl dextran (CMD) based nanomicelles antibacterial coating on microarc-oxidized titanium (MAO-Ti) surface. After cross-linking, the drug-loaded nanomicelles were spherical with a particle size of 130nm and uniformly dispersed. Zeta potential was negative, and the absolute value was greater than 10 mV, effectively avoiding micelles aggregation. It was observed by dynamic light scattering (DLS) that the stability of nanomicelles was significantly improved after cross-linking. The hemolysis rate of micelles was less than 5%, and the overall survival rate of human umbilical vein endothelial cells was more than 90%. After being coated on MAO-Ti surface, the cumulative drug release rate of drug-loaded nanomicelles reached 86.6% after 360 hours. Fluorescence staining of immobilized bacteria showed more dead bacteria on the coating surface, and the number of live bacteria was significantly reduced. It was concluded that dextran-based nanomicelles, which showed long-term drug release properties and excellent biocompatibility, are potential drug carriers for fabricating antibacterial coating on titanium surfaces.

A jointed experimental and theoretical investigation pointing out new insights about the microscopic mechanism of the VOCs (volatile organic compounds) photocatalytic elimination by TiO2 has been done. Methane, hexane, isooctane, acetone and methanol have been photomineralized in a batch reactor. Values of K (adsorption constant on TiO2) and k (mineralization rate constant) of the five VOCs (treating the kinetic data through a Langmuir- Hinshelwood approach) have been determined. Recorded K and k values and performed theoretical calculations allowed us to suggest the involvement of an electron transfer step between the VOC and the hole, TiO2(h+), as the rate determining one.

The effect of microstructure and chemistry of passive films on the kinetics of passive layer growth and passivity breakdown of some Ti-based alloys, namely Ti-6Al-4V, Ti-6Al-7Nb and TC21 alloys was studied. The rate of pitting corrosion was evaluated using cyclic polarization measurements. Chronoamperometry was applied to assess the passive layer growth kinetics and breakdown. Microstructure influence on the uniform corrosion rate of these alloys was also investigated employing Tafel extrapolation and dynamic electrochemical impedance spectroscopy. Corrosion studies were performed in 0.9% NaCl solution at 37 oC, and the obtained results were compared with ultrapure Ti (99.99%). The different phases of the microstructure were characterized by X-ray diffraction and scanning electron microscopy. Chemical composition and chemistry of the corroded surfaces were studied using X-ray photoelectron analysis. For all studied alloys, the microstructure consisted of α matrix, which was strengthened by β phase. The highest and the lowest values of the β phase’s volume fraction were recorded for TC21 and Ti-Al-Nb alloys, respectively. The uniform corrosion rate and pitting corrosion resistance (R_pit) of the studied alloys were enhanced following the sequence: Ti-6Al-7Nb < Ti-6Al-4V << TC21. The corrosion resistance of Ti-Al-Nb alloy approached that of pure Ti. The obvious changes in the microstructure of these alloys, together with XPS findings, were adopted to interpret the pronounced variation in their corrosion rates.

Gamma titanium aluminides (γ-TiAl) present an excellent behaviour under high temperature conditions, being a feasible alternative to nickel-based superalloy components in aeroengine sector. However, considered as a difficult to cut material, process cutting parameters require special study to guarantee components quality. In this work, developed drilling mechanistic model is a useful tool in order to predict drilling force (F_z) and torque (T_c) for optimal drilling conditions determination. The model is validated for three types of Gamma-TiAl alloys. Integral hard metal end-drilling tools and different cutting parameters (feeds and cutting speeds) are tested in three different sized holes for each alloy.

This work focuses on the study of the microstructure, hardening and stiffening effect caused by the secondary phases formed in titanium matrices. These secondary phases were originated from reactions between the matrix and boron particles added in the starting mixtures of the composites. Not only was the composite composition studied as an influencing factor in the behaviour of the composites, but also different operational temperatures. Three volume percentages of boron content were tested (0.9, 2.5 and 5 vol % of amorphous boron). The manufacturing process used to produce the composites was inductive hot pressing, which operational temperatures were between 1000 °C to 1300 °C. Specimens showed optimal densification. Moreover, microstructural study revealed the formation of TiB in various shapes and proportions. Mechanical testing confirmed that the secondary phases had a positive influence on the properties of the composites. In general, adding boron particles increased the hardness and stiffness of the composites; however rising temperatures resulted in greater increases in stiffness than in hardness.

To obtain smooth coatings of TiO2 for building a new design of Ti-6Al-4V heart valve, the anodic oxidation technique in pre-spark conditions was evaluated. TiO2 coating is necessary for its recognize biocompatibility and corrosion resistance. A required feature on surfaces in contact with blood is a low level of roughness (Ra ≤ 50 nm) that not favor the formation of blood clots. The present paper compares the coatings obtained by anodic oxidation of the Ti-6Al-4V alloy using H2SO4 at different concentrations (0.1 M to 4 M) as electrolyte and applying different voltages (from 20 V to 70 V). Color and morphological analysis of coatings are performed using optical and scanning microscopy. The crystalline phases were analyzed by glancing X-ray diffraction. By varying the applied voltage different interference colors coatings were obtained. The differences in morphologies of the coatings, due to the change in concentration, are more evident at high voltages limiting the oxidation conditions for the desired application. Anatase phase was detected from 70 V for 1 M H2SO4. An increase in the concentration of H2SO4 decreases the voltage at which the transformation of amorphous to crystalline coatings occurs, i.e. with 4 M H2SO4 the anatase phase appears at 60 V.

Preventing or treating infections at implantation sites where the risk of bacterial contamination is high requires the development of intelligent drug delivery systems. In this work, honeycomb structures as a potential drug carrier were obtained for the first time in a fast, one-step anodization process of titanium grade 4, lasting only 60 seconds. Fourth generation oxide nanotube layers were obtained from an aqueous solution of 0.5% AgNO3 in the voltage range from 50 to 80 at 15(1) °C. The FE-SEM method showed the length of the oxide nanotubes from 1.02(2) µm at 50 V to 230(8) nm at 80 V. The EDS analysis revealed that during anodizing, silver particles are deposited on the Ti G4 up to 2.2(5) wt.%. Electrochemical measurements by open circuit potential and anodic polarization curves methods proved the improvement of in vitro corrosion resistance as a result of Ti G4 anodizing. Assessment of the anodized Ti G4 as gentamicin sulfate carrier carried out using ATR-FTIR and UV-VIS absorption spectroscopy revealed that the obtained oxide nanotube layers can be used for application of drugs directly to the tissue around the implant. This method of application allows full use of the therapeutic dose of the antibiotic used.

This review article provides useful information on TiO2 and ZnO photocatalysts and their derivatives in removing organic contaminants such as different types of dyes, hydrocarbons, pesticides, etc. Also, the reaction mechanism of TiO2 and ZnO photocatalysts and their derivatives was investigated. In addition, the impact of adding metallic (e.g., Ag, Co, Pt, Pd, Cu, Au, Ni) and non-metallic (e.g., C, N, O, S) dopants to their structure on the photodegradation efficiency of organic compounds was thoroughly studied. Moreover, advantages and disadvantages of various synthesis procedures of ZnO and TiO2 nanocatalysts were discussed and compared. Furthermore, the impact of photocatalyst dosage, photocatalyst structure, contaminant concentration, pH, light intensity and wavelength, temperature and reaction time on the photodegradation efficiency was studied. According to previous studies, adding metallic and non-metallic dopants to the TiO2 and ZnO structure led to a remarkable enhance in their stability and reusability. Besides, doped TiO2 and ZnO demonstrated remarkable photocatalytic efficiencies in eliminating various types of organic contaminants.

For some persistent pollutants, such as recalcitrant pesticides, the polluted water (urban, agricultural and/or industrial) treated by conventional wastewater treatment plants is in some cases insufficient to achieve the legally required level of purity. This issue is of particular concern in areas where low rainfall does not provide sufficient water resources to meet the needs of agriculture, requiring increased reuse of water from wastewater treatment plants. In this context, Advanced Oxidation Processes (AOPs) hold great promise for the removal of organic pollutants. This study first evaluates the effectiveness of UV/S2O8= compared to heterogeneous photocatalysis using UV/TiO2 processes on the degradation of two commonly used herbicides (terbutylazine and isoproturon) in aqueous solutions using a photoreactor. In addition. the effect of UV wavelength on the degradation efficiency of both herbicides was investigated. Although degradation rate was higher under UV-254/S2O8= nm than under UV-365/S2O8= nm, complete degradation of the herbicides (0.2 mg L-1) was achieved within 30 min under UV-366 nm using a Na2S2O8 dosage of 250 mg L-1 in the absence of inorganic anions. To assess the impact of water matrix, the individual and combined effects of sulphate, bicarbonate and chloride were evaluated. They can react with hydroxyl and sulphate radicals formed during AOPs to form new radicals with a lower redox potential. The results showed negligible effects of sulphate, while the combination of bicarbonate and chloride seemed to be the key for the decrease in herbicide removal efficiency found when working with complex matrices. Finally, the main intermediates detected during the photodegradation process were identified and the likely pathways are proposed and discussed.

The current work shows the optimization in the preparation of nanosized titanium carbide (TiC) in-situ through mechanical alloying (MA). Metallic titanium (Ti) powders, along with two carbon sources, carbon nanotubes (CNTs), and stearic acid (SA), were used to reduce the particle size using a high-energy Spex800 mill. The combined use of 2 wt % of these carbon sources and n-heptane as a liquid process control agent (PCA) proved crucial in generating nanoscale powder composites through a simple and scalable synthesis process within a 4-hour timeframe. The use of 20 wt % of both carbon sources was compared to determine the ability of CNTs to form carbides and the decomposition of PCAs during mechanical milling. The result reveals structures like nanoblocks and nanolumps with and important size reduction. The structure and morphology of the composites and starting materials were evaluated through x-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM).

In this article, copper(II) oxide and titanium dioxide nanoparticles were added to Group III base oil formulated with 8 wt% Komad 323 dispersant. The nanoparticles were treated with ethyl oleate surface modification. The tribological properties of the homogenized oil samples were tested on a linear oscillating tribometer with continuous monitoring of static friction. Friction absolute integral values were calculated from high data acquisition. The wear was evaluated using a digital optical and confocal microscope. The wear types were characterized with scanning electron microscopy, while the remaining additives were located and quantified with energy-dispersive X-ray spectroscopy. The measurement results show that the CuO nanoparticles did not work well with the Komad 323 dispersant. As a result of their antagonistic effect, in the case of low CuO concentrations (≤0.3 wt%), the friction increased, while in the case of high concentrations (≥0.4%), surface fatigue caused a high wear rate. The cooperation between TiO2 and the dispersant showed synergistic effects. The oxygen-rich boundary layer formed on the worn surface with a titanium content of 0.33-0.39 norm.wt% provides both lower friction and high wear resistance.

Lewis acid zeolites play an important role in industrially important green reactions closely related to fine chemicals and biomass conversion. Titanium-doped TS-1 zeolite is a milestone Lewis acid zeolite, which widely uses in industrially significant green oxidation processes with hydrogen peroxide as an oxidant under mild conditions. TS-1 Zeolites are normally synthesized in basic condition under hydrothermal treatment. Up to now, it is still not successful to synthesize active TS-1 Lewis acid zeolite by using inorganic alkali, e.g. NaOH or KOH as base, which are cheaper and more stable compared with quaternary ammonium hydroxide or organic amines used in the traditional synthesis. Here, inorganic base of NaOH was firstly employed in synthesizing active TS-1 zeolites. The crucial factor was the control of adverse effects of sodium cations on the incorporation of active titanium cations. A higher catalytic activity could be achieved by further reducing the size of the TS-1 crystal by seed-added strategy, which could approach the catalytic activity of commercial catalyst while the production cost was much lower than the commercial TS-1 catalysts, indicating great commercial potential and the possibility of preparing other cheap Lewis acid catalysts by using inorganic alkali.

Two antimicrobial agents such as silver nanoparticles (AgNPs) and titanium dioxide (TiO2) have been formulated with natural polysaccharides (chitosan or alginate) to develop innovative inks for the rapid, customizable, and extremely accurate manufacturing of 3D printed scaffolds useful as dressings in the treatment of infected skin wounds. Suitable chemical-physical properties for the applicability of these innovative devices were demonstrated through the evaluation of water content (88-93%), mechanical strength (Young’s modulus 0.23-0.6 MPa), elasticity, and morphology. The antimicrobial tests performed against Staphylococcus Aureus and Pseudomonas Aeruginosa demonstrated the antimicrobial activities against Gram+ and Gram– bacteria of AgNPs and TiO2 agents embedded in the CH or ALG macroporous 3D hydrogels (AgNPs MIC starting from 5 µg/ml). The biocompatibility of chitosan was widely demonstrated by cell viability tests and was higher than that observed for alginate. Constructs containing AgNPs at 10 µg/ml concentration level did not significantly alter cell viability as well as the presence of titanium dioxide; cytotoxicity towards human fibroblasts was observed starting with AgNPs concentration of 100 µg/ml. In conclusions, the 3D printed dressings here developed own the features to be cheap, highly defined, easy to be manufactured and further applied in personalized antimicrobial medicine applications.

We determined the optimal composition of reactive magnetron sputtered TiO2-SnO2 mixed layers for electrochromic purposes. We determined and mapped the composition and optical parameters by Spectroscopic Ellipsometry (SE). The Ti‐ and Sn‐ targets have been placed separately, and the Si-wafers on glass substrate (30 cm× 30 cm) were moved under the two separated targets (Ti and Sn) in Ar‐O2 plasma. Different (Effective Medium Approximation (EMA) and oscillator-type) op-tical models were used to obtain the composition maps and thickness of the sample layer. Scanning Electron Microscopy (SEM) with Energy-Dispersive X-ray Spectroscopy (EDS) has been used to check the SE results. The ’goodness’ of diverse optical models have been compared, according to the conditions of sample preparation. We show that in the case of molecular-level mixed layers 2‐Tauc‐Lorentz oscillator model is better than the Bruggeman Effective Medium Approximation (BEMA). The electrochromic properties of mixed metal oxides that deposited by reactive sputtering have been mapped, too.

In order to produce nanostructured Ti0.9Cr0.1C powders, an elemental powder mixture of titanium, chromium, and graphite is milled in this work using a high-energy ball mill for various milling times. Microstructural characteristics such as crystallite size, microstrain, lattice parameter, and dislocation density are determined using X-ray diffraction (XRD). Mechanical alloying successfully produced nanocrystalline (Ti,Cr)C with an average crystallite size of 11 nm. This size of the crystallites is also directly verified using transmission electron microscopy (TEM). Scanning electron microscopy (SEM) was used to investigate the morphology of the samples. The novelty of this work is advancing the scientific understanding of the effect of milling time on the particle size distribution and crystalline structure, and also understanding the effect of the spark plasma sintering on the different properties of the bulks. Densified cermet samples were produced from the nanocrystalline powders, milled for 5, 10 and 20 hours by SPS process at 1800 degrees for 5 min under a pressure of 80 MPa. Phase changes of the produced cermets were examined according to XRD, SEM/EDX analyses. Significant amounts of Cr and Fe elements were detected, especially in the 20 h milled cermet. The bulk forms of the milled powders for 5 and 20 h had a relative density of 98.43 and 98.51 %, respectively. However, 5 h milled cermet had 93.3 HRA because of the more homogeneous distribution of the (Ti,Cr)C phase, the low iron content and high relative density. According to the 0.0011 mm/year corrosion rate, and 371.68 kΩ*cm2 charge transfer resistance obtained from the potentiodynamic polarization and EIS tests, the 20 h cermet was the specimen with the highest corrosion resistance.

Metal/metal composites represent a particular class of materials showing innovative mechanical and electrical properties. Conventionally, such materials are produced by severely plastically deforming two ductile phases via rolling or extruding, swaging, and wire drawing. This study presents the feasibility of producing metal/metal composites via a capacitive discharge-assisted sintering process named electro-sinter-forging. Two different metal/metal composites with CP-Ti/AlSi10Mg ratios (20/80 and 80/20 %vol) are evaluated, and the effects of the starting compositions on the microstructural and compositional properties of the materials are presented. Bi-phasic metal/metal composites constituted by isolated α-Ti and AlSi10Mg domains with a microhardness of 113 ± 13 HV_0.025 for the Ti20-AlSi and 244 ± 35 HV_0.025 for the Ti80-AlSi are produced. The effect of the applied current is crucial to obtain high theoretical density, but too high currents may result in Ti dissolution in the Ti80-AlSi composite. Massive phase transformations due to the formation of AlTiSi based intermetallic compounds are observed through thermal analysis and confirmed by morphological and compositional observation. Finally, a possible explanation for the mechanisms regulating densification is proposed accounting for current and pressure synergistic effects.

Food additives are used for a variety of technological or processing reasons, including to add or restore colour in a food. In European Union (EU) the safety of food additives was in history assessed by the Scientific Committee on Food, while the role of risk accessor is not in hands of the European Food Safety Authority (EFSA). Only additives for which the proposed uses is considered safe are on the EU list of authorized additives. Very recently – in May 2020, a scientific opinion was published by the EFSA, concluding that TiO2 can no longer be considered as a safe food additive, and the European Commission is expected to remove it from list of authorized food additives in near future. Our aim was to investigate the trends in the use of TiO2 in the food supply. A case study was conducted in Slovenia, using two nationally representative cross-sectional datasets of branded foods. Original sample contained 49,919 pre-packed food items, while analyses was done on N=12.644 foods (6.012 and 6.632 in 2017 and 2020, respectively) from 15 food subcategories, where TiO2 was found as food additive. Overall, we observed significantly decrease in use of TiO2 (3.6% vs. 1.8%; p<0.01) in the course of these three years. The most TiO2-containing foods were in the Chewing gum category (36.3%) in 2017, and Chocolate and sweets (45.9%) in 2020. Meanwhile in 2017 the largest within-category share of TiO2-containing foods was Chewing gum category, namely 70.3%, and those products presented over 85% of the market-share. In 2020 only 24.6% chewing gums contained TiO2, and those were accounting only 3% of the market share. In con-clusion, we showed overall decrease of TiO2 use and considerable improvements in certain food categories (particularly in chewing gums) despite the fact, that this additive has not yet been of-ficially removed from the list of authorized additives. Specific food categories (i.e. Chocolate and sweets) were identified, where product-reformulation is needed, and where official controls by authorities will be most relevant.

Hybrid materials of conjugated polymer and titanium(IV) oxide have attracted considerable attention concerning potential benefits, including (i) efficient exploitation of visible light, (ii) high adsorption capacity for organic contaminants, (iii) effective charge carriers separation. The new class of the photocatalysts is promising for the removal of environmental pollutants in both aqueous and gaseous phases. For the first time, in this study, the PANI/TiO₂ hybrid composite was used for the degradation of phenol in water and toluene in the gas phase. Polyaniline-TiO₂ was prepared by in-situ polymerization of aniline on the TiO₂ surface. The obtained hybrid material was characterized by diffuse reflectance spectroscopy (DR/UV-Vis), X-ray diffraction (XRD), fast-Fourier transformation spectroscopy (FTIR), photoluminescence (PL) spectroscopy, microscopy analysis (SEM/TEM) and thermogravimetric analysis (TGA). An insight into the mechanism was shown based on the photodegradation analysis of charge carriers scavengers. Polyaniline is an efficient TiO2 photosensitizer for photodegradation in visible light (λ> 420 nm). The trapping experiments revealed that mainly h+ and ˙OH were reactive oxygen species responsible for phenol degradation. Furthermore, the PANI-TiO₂ hybrid nanocomposite was used in gypsum plaster to study the self-cleaning properties of the obtained building material. The effect of PANI-TiO₂ content on hydrophilic/hydrophobic properties and crystallographic structure of gypsum was studied. The obtained PANI-TiO₂ modified gypsum plaster had improved photocatalytic activity in the reaction of toluene degradation under Vis light.

As a photo-catalytic titanium oxide film deposition process, thermal spray is hoped to be utilized practically on the condition that it is relatively easy to deposit anatase rich films. However, because of its high equipment and feedstock powder costs, it is very difficult to introduce thermal spray equipment into small companies. In this study, to develop a low cost thermal spray system, low power atmospheric suspension plasma spray equipment with titanium hydroxide suspension created by hydrolysis of titanium tetra iso butoxide using Ar, N2 as working gases. For avoiding sedimentation of the hydroxide particles in the suspension, mechanical milling of the suspension was conducted to create colloidal suspension before using it as feedstock. Moreover, an Ultrasonic wave container was used to keep the suspension particles moving while the spray process was conducted. After the film deposition, with As for the coating, anatase rich TiO2 film could be obtained. For characterization of the film, microstructure observation by optical microscope and X-ray diffraction was carried out. Consequently, by creation of colloidal suspension, deposition could be conducted without sedimentation of the hydroxide particle in the suspension during operation. Besides, it was proved the film had enough photo-catalytic property to decolor methylene-blue droplet

Cu,N-TiO₂ nanotube (Cu,N-TNT) is prepared through a novel magnetron sputtering and anodic oxidation method. Then the morphology, structure and physicochemical property of Cu,N-TNT was analyzed by XRD, SEM, TEM, EDX and UV-vis-DR. The results indicate that the evenly doped copper is beneficial to the transformation of the TNT from anatase to rutile and play a key role in the morphology of the Cu,N-TNT. The doped Cu and N in the TNT influence the growth orientation of the TiO₂ crystals, which result in the lattice distortion and wider the interplanar spacing 60s-Cu,N-TNT has less band gap and stronger absorption intensity in visible region than other Cu,N-TNT samples, which make the combination rate of photogenerated electron and photogenerated hole decrease greatly, thus beneficial to its physicochemical property.

In the paper, the effect of voltage increasing (from 500 VDC up to 650 VDC) on the structure and chemical composition of porous coating on titanium made by Plasma Electrolytic Oxidation, is presented. In the present paper, phosphates based coatings enriched with calcium, magnesium, zinc and copper in electrolyte based on 1 L of 85% concentrated H3PO4 with additions of Ca(NO3)2·4H2O, and Mg(NO3)2∙6H2O, and Zn(NO3)2∙6H2O, and Cu(NO3)2∙3H2O, are described. The morphology, chemical and phase composition, are evaluated using SEM, EDS, XRD, XPS, GDOES. Based on all the analyses, it was found out that the PEO coatings are porous and enriched with calcium, magnesium, zinc and copper. They consist mainly of the amorphous phase, which is more visible for higher voltages, and it is correlated with the increasing of the total PEO coating thickness (the higher the voltage, the thicker the PEO coating). However, for 650 VDC an amorphous phase and titanium substrate was also recorded with a signal from Ti2P2O7 crystalline, that was not observed for lower voltages. It was also found out that all the obtained coatings may be divided in three sub-layers, i.e. porous, semiporous, and transition one.

This work investigated the fabrication, properties, and sensing applications of TiO2 nanotubes. A purity of 99.7% and 1mm thickness of titanium metal sheet was used to elaborate titanium dioxide nanotubes for gas sensor application through electrochemical anodization in a mixture of Ethylene glycol (EG)/NH4F electrolytes. As a result, X-ray diffraction indicates the crystallization of the titanium dioxide layer. Scanning electron microscopy and Transmission electron microscopy reveal that the average diameter of the TiO₂ nanotubes is approximately 100 nm, with tube length ranging between 3 and 9 microns and a thickness of the nanotube walls of about 25 nm. This type of TiO2 nanotube is suitable for NO2 gas sensor applications. As a result, at an oxidation time of 15 min, the detection of TiO2 nanotube gas toward NO2 gas shows a good result at 250 °C, when exposed to a NO2 gas flow of 100 ppm, where a maximum NO2 gas response of 96% was obtained. The sensors based on the TiO2 nanotube arrays for sensing NO2 all exhibited high stability, good reproducibility, and high sensitivity. This work suggests that TiO2 nanotubes are a promising material for application as a NO2 sensor, as well as other applications.

In recent years, the contamination of aquatic environments by organic chemicals has become an increasing concern. To effectively remove toxic pollutants and biologically resistant compounds, a combination of advanced technologies must complement conventional methods. Indeed, among environmental pollutants, dyes such as methylene blue (MB), congo red and crystal violet persist in the environment because they are difficult to biodegrade. Advanced oxidation processes (AOPs) are widely employed to treat various types of wastewaters, often in conjunction with bi-ological treatments. Among these technologies, heterogeneous photocatalysis stands out as one of the most extensively studied, with Titanium dioxide being the most researched photocatalyst due to its high photoactivity. In this study, Titanium dioxide nanoparticles (NPs) were synthe-sized using both a green method, leveraging the natural properties of Aloe vera leaf extract, and a conventional approach. The resulting NPs were thoroughly characterized using XRD, TEM, and ζ-potential analysis. Their photocatalytic performance was assessed by measuring the degrada-tion of MB under UV light. The TiO2 NPs synthesized via the green method demonstrated a degradation efficiency of (50 ± 3) % after 180 minutes, significantly higher than the (16 ± 3)% achieved by NPs synthesized through the conventional route. Moreover, the reaction rate con-stant for the green-synthesized TiO2 NPs was found to be approximately five times greater than that of the conventionally synthesized NPs. These results open new scenario in the pollution removing strategy research.

The study reports the effect of some metal carbides (niobium carbide, vanadium carbide, titanium carbide, and manganese sulfide) on hydrogen embrittlement in the pipeline industry using plane wave’s density functional theory (DFT). Our results predicted that the interaction of hydrogen molecules with these metals carbide occurs in the long range with binding energy varying in the energy window [0.70eV to 0.043eV]. Also, our study shows the desorption of H2 molecules from these metal carbides in the chemisorptions. Since, hydrogen embrittlement, occurs in the atomic state of hydrogen, therefore our finding in the atomic interaction of hydrogen with NbC, VC, TiC, and MnS showed that the strength of the trapping of the hydrogen atom could be classified as: TiC+H>VC+H>NbC+H> MnS+H. In addition, our study reveals that the carbon site is the most favorable hydrogen trapping site than the metal one. Furthermore, our results demonstrate that increasing the layer can also be an efficient way to enhance the trapping capacity.

The mechanical properties, structure, and morphology of milled and 3D printed Ti-6Al-4V alloys produced by selective laser melting were investigated in this study. The mechanical properties were investigated by means of nanoindentation, a tensile test, and a three-point bending test. The Atomic Force Microscope (AFM) was used to study the surface topography and roughness of both titanium alloys. The surface structure and phase analysis were studied by a scanning electron microscope (SEM) and through powder X-ray diffraction (XRD). The results from the nanoindentation experiments showed that the 3D-printed sample has higher indentation hardness and modulus than the milled one. The AFM observation of the surface topography of the samples showed that the milled sample has a higher roughness than the 3D-printed one. The tensile test results showed that the 3D printed sample by means of Selective Laser Melting (SLM) technology has about 26% higher tensile strength and smaller elongation than the milled one. The 3-point bending test revealed that the 3D printed Ti-6Al-4V sample has higher flexural strength than the milled one. It was found that the 3D-printed sample has a smaller crystal size than the milled one, which, according to the Hall-Petch relationship, leads to its higher indentation hardness.

Titanium middle ear prostheses are widely used in surgical practice due to their acoustic properties. However, they present a significant drawback shared by all synthetic materials currently in use for middle ear reconstruction: they can be rejected by the organism of the host. In this study, we aim to review the current literature on titanium TORP and PORP extrusion and dislocation. Eighty-one articles were analysed after full article review based on the inclusion and exclusion criteria. The most common indication for reconstruction was chronic otitis media with cholesteatoma. The average extrusion or dislocation rate was 5.1%, ranging from 0 to 35%. The average improvement in air-bone gap was 12.3 dB (1.6 dB to 25.1 dB) and 13.7 (-0,5 dB to 22.7 dB) for PORP ad TORP groups, respectively. The data reported on this topic are highly variable, demonstrating the functional outcomes are difficult to predict in clinical practice. We believe the current limitations could be overcome with technological developments, including bioengineering research focused on promoting the prothesis adaptation to the ME environment.

Due to the high specific surface area of titanium aluminide powders, significant and unavoidable surface oxidation takes place during processing. The resulting oxides disrupt the conventional powder metallurgical process route (pressing and sintering) by reducing green strength and sintered properties. Oxide-free particle surfaces offer the potential to significantly increase particle bond strength and enable the processing of difficult-to-press material powders. In this work, the effect of milling titanium aluminide powder in a silane-doped atmosphere on the component properties after pressing and subsequent sintering was investigated. Ball milling was used to break up the oxide layers and create bare metal surfaces on the particles. With the help of silane-doped inert gas, the oxygen partial pressure was greatly reduced during machining. It was investigated whether oxide-free surfaces could be produced and maintained by milling in silane-doped at-mospheres. Furthermore, the resulting material properties after pressing and sintering were an-alyzed using density measurements, hardness tests, EDX-measurements and micrographs. It was concluded, that ball milling in a silane-doped atmosphere produces and maintains oxide-free particle surfaces. These oxide-free surfaces and smaller particle sizes improve the component properties after pressing and sintering.

The tricellular tight junction protein angulin-1/lipolysis-stimulated lipoprotein receptor (LSR) is associated with numerous signal transduction pathways that regulate gene expression, epithelial cell function, and morphogenesis. The impacts of particulate matter on LSR and asthma are not known. Therefore, the aim of the present study was to assess the impacts of particulate matter as one of air pollution on LSR expression in asthma. To this end, we investigated the involvement of LSR in the pathogenesis of bronchial asthma in an ovalbumin (OVA) mouse model of asthma exposed to titanium dioxide (TiO2), and examined plasma LSR levels and their relationship with clinical variables in asthma patients and healthy controls. Plasma LSR levels were lower in asthma patients than in healthy controls. Although plasma levels of receptor for advanced glycation end-products (RAGE) were lower in asthma patients than in healthy controls, high mobility group box protein 1 (HMGB1) levels did not differ between these groups. In asthma patients, LSR levels were correlated with the forced vital capacity percentage, ratio of forced expiration (first second)-to-forced vital capacity, white blood cell count, and blood lymphocyte proportion. In mice, LSR expression was significantly decreased in OVA mice compared with control mice, and changed in OVA mice exposed to TiO2. Transforming growth factor beta levels were increased in OVA mice compared with control mice, and changed in OVA mice exposed to TiO2. Overall, plasma LSR levels were decreased in asthma patients, and were influenced by exposure to air pollution. These findings suggest the involvement of LSR in the pathogenesis of asthma.

The topography and chemical composition modification of the titanium (Ti) implants play a decisive role in improving biocompatibility and bioactivity, accelerating osseointegration, and, thus, determining clinical success. In spite of the development of surface modification strategies, bacterial contamination is a common cause of failure. The use of systemic antibiotic therapy does not guarantee action at the contaminated site. In this work, we proposed a surface treatment for Ti implant that aim to improve its osseointegration and reduce bacterial colonization in surgery site due to local release of antibiotic. The Ti disks were hydrothermally treated with 3M NaOH solution to form a nanostructured layer of titanate on the Ti surface. Metronidazole was impregnated on these nanostructured surfaces to allow its local release. The samples were coated with poly(vinyl alcohol) - PVA films with different thickness to evaluate a possible control of drug release. Gamma irradiation was used to crosslink the polymer chains leading to a hydrogel layer formation and to sterilize the samples. The samples were characterized by XRD, SEM, FTIR, contact angle measurements, “in vitro” bioactivity, and drug release analysis. The alkaline hydrothermal treatment successfully produced intertwined, web-like nanostructures on the Ti surface, providing wettability and bioactivity to Ti samples (Ti+TTNT samples). Metronidazole was successfully loaded and released from Ti+TTNT samples coated or not with PVA. Although the polymeric film acted as a physical barrier to drug delivery, all groups reached the minimum inhibitory concentration for anaerobic bacteria. Thus, the surface modification method presented is a potential approach to improve the osseointegration of the Ti implant and to associate local drug delivery to dental implants, preventing early infections and bone failure.

The 8Nb isopleth section of a Ti-Al-Nb system is experimentally determined based on thermal analysis and thermodynamic calculation methods to obtain the phase transformation and equilibrium relations required for material design and fabrication. The phase transus and relations for the 8Nb-TiAl system show some deviations from the calculated thermodynamic results. The ordered βo phase transforms from the disordered β/α phases at 1200–1400 °C over a large Al concentration range, and this transformation is considered to be an intermediate type between the first- and second-order phase transitions. Moreover, the βo phases are retained at the ambient temperature in the 8Nb-TiAl microstructures. The ωo phase transforms from the highly ordered βo phase, rather than from α2 or βo with low degree of atom ordering B2 (LOB2) structure, with Al concentration of 32–43 at.% at approximately 850 °C. From the experimental detection, the transition of the ωo phase from the βo phase is considered to be a further ordering process.

Ag/TiO₂ thin films were prepared using the sol-gel spin coating method. The microstructural growth behaviors of the prepared Ag/TiO2 thin films were elucidated using real-time synchrotron radiation imaging, its structure determined using grazing incidence X-ray diffraction (GIXRD), its morphology imaged using the field emission scanning electron microscopy (FESEM), and its surface topography examined using the atomic force microscope (AFM) in contact mode. Cubical white spots were detected, identified as Ag, while the TiO₂ thin film resembles a porous ring-like structure with each ring coalescing and forming channels. Junction growth is directly proportional with time under continuous heating conditions (annealing), and its growth orientations and patterns were seemingly random.

In this study, functionalized-MWCNTs with 3-aminopropyltriethoxysilane (APTES) loaded titania nanoparticles (MWCNTs-APTES-TiO₂) were prepared to investigate their physicochemical properties and photocatalytic activity for methyl orange (MO) degradation. The TiO₂ nanoparticles, functionalized-MNCNT and composite powders were characterized by XRD, raman, and TEM. The results obtained proved that titania (TiO₂) nanoparticles was successfully loaded on APTES-MWCNTs. The best photocatalytic degradation of methyl orange solution under UV light irradiation was recorded over MWCNTs-APTES-TiO₂ (1:2), with 87% after 180 min. Kinetic analysis indicated that photocatalytic degradation of MO solution by MWCNTs-APTES-TiO₂ obeyed second-order kinetic model (R² > 0.95), supported by half-life equations and graph. The presence of carbon nanotubes accelerated the degradation of methyl orange due to inhibition of electron-hole recombination, the formation of additional hydroxyl radicals and functional groups of the latter had an inhibitory effect on the degradation of methyl orange. This study shows that the MWCNTs-APTES-TiO₂ nanocomposites exhibit promising photocatalytic degradation against methyl orange.

The presence of clays in copper minerals has a significant negative impact during their processing, leading to low recoveries during the flotation process. In saline environments such as seawater, the presence of clays contribute to an increase in operational problems caused by salinity, a decrease in the grade of the copper concentrate, alteration of the rheology of the mineral pulp, a decrease in the selectivity of copper during the flotation process, a reduction in the quality of clarified water, and excessive corrosion of metallic components. This study explores the electroflotation of kaolinite and montmorillonite clays in NaCl solutions using a modified Hallimond tube coupled with Ti Gr. 2 electrodes for bubble generation via water electrolysis, and the corrosion analysis of these electrodes applying the superposition model. The electroflotation results show recovery of clays close to 72.68% for kaolinite, 88.44% for montmorillonite, and 67.36% for a mixtures of both clays. The presence of clays helps reduce the corrosive effects of Ti Gr. 2 from 0.069 A/m2 in NaCl to 0.0073 A/m2 in NaCl with montmorillonite clay.

Refractory materials are used worldwide in process equipment. However, gaseous and liquid process products penetrate the surface layer, and deep into the volume of refractories destructing rather expensive constructions complicated to repair. To address this challenge, there is a need to develop protective coatings for refractory that can limit the penetration of working media and extend their operational lifespan. In this work, the application of gas-dynamic cold spraying (CGDS) to produce a coating on the refractory using fine titanium dioxide (TiO2) particles is explored. These particles are accelerated within a nitrogen flow, passing through a Laval nozzle, and then sprayed onto a fireclay surface. The mechanisms of particle deposition and layer formation on porous surfaces through experiments and numerical simulations were investigated. The geometry of a typical refractory pore was determined, which was then incorporated into Computational Fluid Dynamics (CFD) simulations to model the cold spraying process of porous substrates. As a result, the influence of the particle size on its velocity and angle of penetration into pores was established. Experimental findings demonstrate the effective closure of pores and the formation of a particle layer on the refractory surface. Furthermore, the nanoindentation tests for the refractory samples showcase capabilities for checking coating thickness for porous materials.

The large energy band gap associated with titanium oxide nanoparticle is a limitation to its application as a photo catalyst within the solar spectrum. More than 45% of solar radiation can be utilized at a reduced energy band gap of 〖TiO〗_2. Various structural modifications in 〖TiO〗_2 targeted in optimized photo catalyst application include the enhancement of its support system. Activated carbon supported 〖TiO〗_2 nanoparticle may produce the desired reduction in the energy band gap, reduce electron recombination and consequently enhance its photocatalytic activity in the visible region of electromagnetic spectrum. In the current investigation, an activated carbon made from the leaves of an invasive plant (Acacia Saligna) was applied as a support in the synthesis (hydrothermal process) of 〖TiO〗_2 nanoparticle. The determination of energy band-gap of 〖TiO〗_2 supported activated carbon using UV-Vis spectrophotometer gave 2.11 eV. Likewise, Scanning Electron Microscopy (SEM-EDS), Fourier transformer infrared (FTIR), XRD and Brunauer- Emmett-Teller (BET) showed that 〖TiO〗_2was successfully immobilized on the activated carbon’s external surface. The BET results showed that the synthesized 〖TiO〗_2exhibits small hysteresis phenomenon which represent a typical type IV isotherm attributed to mesosoporous material with a low porosity. Meanwhile, these XRD results reveal the presence of mixture of rutile and anatase crystalline phase

Titanium dioxide nanoparticles (TiO2NPs) are used in products that are applied to the human body, such as cosmetics and food, but their biocompatibility remains controversial. Pycnogenol (PYC), a natural extract of pine bark, exerts anti-inflammatory and antioxidant effects. In this study, we investigated whether PYC effectively alleviates pulmonary toxicity induced by airway exposure to TiO2NPs, and the beneficial effects of PYC were explained through the analysis of changes to the mechanism of cytotoxicity. TiO2NPs induced pulmonary inflammation and mucus production, increased the levels of malondialdehyde, and upregulated thioredoxin-interacting protein (TXNIP) and cleaved-caspase 3 (Cas3) in the lungs of mice. However, PYC treatment reduced the levels of all toxicity markers of TiO2NPs and restored glutathione levels. These antioxidant and anti-inflammatory effects of PYC were also demonstrated in TiO2NP-exposed human airway epithelial cells by increasing the mRNA levels of antioxidant enzymes and decreasing the expression of TXNIP, cleaved-Cas3, and inflammatory mediators. Taken together, our results showed that PYC attenuated TiO2NP-induced lung injury via TXNIP downregulation. Therefore, our results suggest the potential of PYC as an effective anti-inflammatory and antioxidant agent against TiO2NP-induced pulmonary toxicity.

This article describes the synthesis of hydroxyapatite (HAp) flakes through a microwave-assisted hydrothermal method. These flakes are intended for use as substrates for depositing titanium dioxide (TiO2) films using chemical vapor deposition with metal–organic precursors (MOCVD). The results reveal the formation of crystalline hydroxyapatite characterized by a uniform mor-phology. Additionally, we demonstrated the successful deposition of TiO2 coatings on the hy-droxyapatite flakes, resulting in a distinctive faceted prism morphology. Our findings affirm the effective synthesis of the HAp/TiO2 composite material. To further explore the material’s practical applications, we recommend assessing the photocatalytic activity of these composite membranes in future research.

The use of metal oxide nanoparticles as an alternative antimicrobial agent has gained attention due to the increasing problem of antibiotic resistance. Understanding its properties and potential benefits can contribute to the development of more effective and sustainable treatments in veterinary medicine. The aim of this study was to characterize TiO2-NP formulations and evaluate their antibacterial and wound healing abilities. The diameters and zeta potentials were determined using the Zetasizer in conjunction with dynamic light scattering. The agar-well diffusion method, time-kill kinetic assay and crystal violet assay were used to evaluate their antimicrobial activities. Wound healing assays were conducted both in-vitro and in-vivo. The study demonstrated that TiO2-NP formulations exhibit significant antimicrobial properties against various bacterial strains such as S. aureus and E. coli. No measurable E. coli growth was observed within a 15-mins period following exposure to TiO2-NP formulations. The TiO2-NP formation can improve wound healing by enhancing cell migration and collagen formation in both in-vitro and in-vivo conditions. In summary, our study suggests that TiO2-NP has the potential for use as an antimicrobial agent for animal wound treatment due to its ability to suppress bacterial growth and biofilm formation, as well as to enhance wound healing.

The work reports a facile synthesis of high thermally-stable nanocrystalline anatase TiO2 nanoparticles (NPs) doped with different atomic concentrations (0.5, 1.0, 3.0, and 6.0%) of Gd3+ and Nd3+ ions by a template-free and one-step solvothermal process, using titanium(IV) butoxide as titanium precursor and dimethyl sulfoxide (DMSO) as solvent. The structure and morphology of the Gd3+, Nd3+, and 0.5%Gd3+-0.5%Nd3+/doped TiO2 NPs have been characterized by using various analytical techniques. The Gd3+/ and Nd3+/TiO2 molar ratios were found to have a pronounced impact on the crystalline structure, size, and morphology of TiO2 NPs. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) studies revealed the proper substitution of Ti4+ by Gd3+ and Nd3+ ions in the TiO2 host lattice. The as-prepared Gdx/TiO2, Ndx/TiO2, and Gd1.0/Ndx/TiO2 bimetallic NPs, x = 0.5, 1.0, 3.0, and 6%, have been investigated as electrocatalysts for hydrogen evolution reaction (HER) in 1.0 M KOH solution using a variety of electrochemical techniques. At any doping percentage, the Gd1.0/Ndx/TiO2 bimetallic NPs showed higher HER catalytic performance than their corresponding counterparts i.e. Gdx/TiO2 and Ndx/TiO2. Upon increasing the Nd content from 0.5 to 6.0%, the HER catalytic performance of the Gd1.0/Ndx/TiO2 bimetallic NPs was generally enhanced. Among the studied materials, the bimetallic Gd1.0/Nd6.0/TiO2 NPs emerged as the most promising catalyst with an onset potential of -22 mV vs. RHE, a Tafel slope of 109 mV dec-1, and an exchange current density of 0.72 mA cm-2. Such HER electrochemical kinetic parameters are close to those recorded by the commercial Pt/C (onset potential: -15 mV, Tafel slope: 106 mV dec-1, and exchange current density: 0.80 mA cm-2), and also comparable with those measured by the most active electrocatalysts reported in the literature. The synergistic interaction of Gd and Nd is thought to be the major cause of the bimetallic catalyst's activity.

The problem of filling the bone cavity-forming after tooth extraction remains relevant in maxillo-facial surgery. There is a large selection of osteotropic materials of various natures for filling bone defects. In this article, our experience in the treatment of patients with combined mandible angle fracture and radicular cyst and fractures is introduced. A feature of the treatment is to fill the bone defect with the osteotropic material. Using collagen osteotropic material, possessing osteoconductive property can improve the treatment of patients with mandibular fractures within the dentition. This is due to both the stabilization of the fracture line, a decrease in the likelihood of displacement of fragments along with fixation with devices, and a reduction in the time of bone tissue regeneration, which reduces the rehabilitation period and allows further orthopedic treatment of patients after 4-5 months without additional bone grafting operations.

Background: Nowadays investigations in the field of dental implants engineering are focused on bioactivity and osseointegration properties.Objective: In this study, the oxide-covered titanium was functionalized by vitamin D3 molecules via a simple self-assembly method with the aim to design more corrosion resistant and at the same time more bioactive surface.Methods: Surface properties of the D3-coated titanium were examined by scanning electron microscopy, attenuated total reflectance Fourier transform infrared spectroscopy, and contact angle measurements, while a long-term corrosion stability during immersion in an artificial saliva solution was investigated in situ by electrochemical impedance spectroscopy.Results: Results of all techniques confirmed a successful formation of the D3 vitamin layer on the oxide-covered titanium. Besides very good corrosion resistivity (~5 MΩcm² ) the D3-modified titanium surface induced spontaneous formation of biocompatible bone-like calcium phosphates (CaP).Conclusion: Observed in vitro CaP-forming ability as a result of D3-modified titanium/artificial saliva interactions could serve as a promising predictor of in vivo bioactivity of implant materials.

In recent years extensive studies have been continuously undertaken on the design of bioactive and biomimetic dental implant surfaces due to the need for improvement of the implant-bone interface properties. In this paper, the titanium dental implant surface was modified by a bioactive vitamin D3 coating prepared by self-assembly process. Surface characterization of the modified implant was performed by field emission scanning electron microscopy (FE-SEM), attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR), and contact angle measurements (CA). Implant’s electrochemical stability during exposure to an artificial saliva solution was monitored in situ by electrochemical impedance spectroscopy (EIS). Experimental results obtained were corroborated by means of quantum chemical calculations at the density functional theory level (DFT). The formation mechanism of the coating onto the titanium implant surface was proposed. During a prolonged immersion period, the bioactive vitamin D3 coating effectively prevented the underlying titanium from corrosive attack (polarization resistance in order of 10⁷ Ω cm²) with ~95% protection effectiveness.

Novel ternary photocatalyst TiO₂-ZnO/g-C₃N₄ was synthesized via a ball milling-assisted sol-gel method and its photocatalytic performance was tasted in photocatalytic degradation of methyl orange (MO) and metoprolol (MTP) under UV and Visible light. The samples were characterized using X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), UV-visible diffuse reflectance spectroscopy (UV-Vis DRS), scanning electron microscopy (SEM), and nitrogen physisorption. Optical measurements confirmed that the combination of TiO₂, ZnO, and g-C₃N₄ extended the visible light absorption to 2.63 eV. SEM and FTIR revealed correct coupling between the three semiconductors, and hole density analysis suggested a synergistic effect reducing charge recombination. Additionally, reuse tests demonstrated the chemical stability of the material. In terms of pollutant degradation, the TiO₂-ZnO/g-C₃N₄ composite efficiently removed 97.75% of MO under UV-LED light and 98.57% under visible light in 300 minutes. Similarly, MTP degradation test reached 86.42% and 86.08% under UV-LED and visible light, respectively, after 300 minutes. These results highlight the material's potential for environmental applications, particularly in contaminant removal through photocatalysis.

Synthesis and structural analysis of (Me3SiC5H4)TiCl2(OAr) [OAr = O-2,6-iPr2-4-RC6H2; R = H, SiEt3] that exhibit higher catalytic activities than (tBuC5H4)TiCl2(OAr), Cp*TiCl2(OAr) with efficient comonomer incorporation in the ethylene/styrene copolymerization in the presence of methylaluminoxane (MAO) cocatalyst. The catalytic activity in the copolymerization increased upon increasing the styrene concentration charged along with increase in the styrene content in the copolymers, whereas the activities by other catalysts showed the opposite trend. (Me3SiC5H4)TiCl2(O-2,6-iPr2C6H3) displayed the most suitable catalyst performance in terms of the activity and the styrene incorporation to afford the amorphous copolymers with styrene contents higher than 50 mol% (up to 63.6 mol%) with random styrene incorporation confirmed by 13C-NMR spectra.

Electrochromic measurements have been performed throughout the full composition range of reactive magnetron-sputtered mixed Titanium oxide and Molybdenum oxide (TiO2-MoO3) to search for enhanced Coloration Efficiency (CE). Optical parameters and composition have been determined and mapped by using Spectroscopic Ellipsometry (SE). Scanning Electron Microscopy (SEM) with Energy-Dispersive X-ray Spectroscopy (EDS). EDS has been used to check the SE results as it was used in our earlier paper [N. T. Ismaeel et al, Materials 2023, 16(12), 4204] for (TiO2-SnO2). Ti and Mo targets were put separately from each other, and the Indium-Tin-Oxide (ITO) covered glass and Si-probes on a glass substrate (30 cm × 30 cm) were moved under the two separated targets (Ti and Mo) in a reactive Argon-Oxygen (Ar-O2) gas mixture. By using this combinatorial process, all the compositions (from 0 to 100%) were achieved in the same sputtering chamber after one sputtering process. The CE (the change of light transmission for the unit electric charge) of mixed metal oxides (TiO2-MoO3) that are deposited by reactive sputtering has been studied in an electrochemical cell. This paper aims to assess the results of investigations of such materials showing the enhanced electrochromic behavior compared to the pure materials and to enhance the Coloration Efficiency.