Taking into account the increase in the emission of greenhouse gases produced by ships, during navigation and maneuvering in the port, a direct consequence of the increase in maritime traffic, the international community has developed a broad set of regulations to limit such emissions. The installation in commercial ports of automatic mooring systems by means of vacuum suction cups (AMS), thus reducing considerably the time required to carry out the mooring and unmooring maneuvers of ships, is a factor that is considerably influencing the decrease in Emissions of polluting gases in commercial ports with high traffic. The objective of the present work is to verify the influence of the use of the AMS on the emissions of polluting gases produced in the facilities destined to the traffic of container ships. It examines the CO2 emissions of container ships that call in the only three container ports equipped with AMS: Salalah (Oman), Beirut (Lebanon) and Ngqura (South Africa). Between them, these three ports supported the transit of 6 million TEUS in 2017. The calculation of emissions is made taking into account the time saved when performing the mooring maneuvers using the new AMS system compared with when it is not used. To do this, two different calculation methods are used: EPA and ENTEC to then compare the results of the two and thus obtain the reduction in emissions per TEU in these terminals during the mooring maneuvers. The paper concludes with a discussion on the values of the reductions in emissions obtained and the advantages of the installation of AMS in commercial ports located near population centres.

The link between ICTs, freight transport, and CO₂ emissions has not received much explicit examination by researchers, despite freight transportation being an egregious contributor to environmental degradation. This paper investigates how ICTs can affect environmental quality when interacting with freight transport activities in 43 countries over the period 2002-2014, using carbon emissions as a proxy for environmental damages. ICTs are measured in terms of internet, telephone, and mobile phone technologies. Using GMM methodology, the results show that ICTs contribute to dampening environmental degradation when interacting with freight transport activities. Specifically, a 10% increase in the interaction between ICTs and freight transportation will decrease carbon emissions by between 1.27% and 3.02%. The results further suggest that fixed and smartphone technologies are the main contributors to reducing emissions when adopted in some specific transport sectors (i.e. road, rail, and inland), while the internet is the most efficient technology when interacting with air transport activity. In addition, the interaction between ICTs and multimodality accelerates environmental quality. The policy implications of these findings are discussed.

Roadway accidents significantly contribute to intermittent congestion and increased CO2 emissions on freeways. This research introduces a statistical approach designed to predict the rise in CO2 emissions resulting from traffic disturbances or jams triggered by such incidents. It also assesses the influence of varying levels of accident management effectiveness in different situations. To construct these scenarios, the study employs VISSIM, a traffic modeling software, incorporating diverse factors such as traffic volume, vehicle types, incident durations, and freeway lane counts. It then produces traffic flow characteristics in the form of vehicle paths. The emission estimates are derived by correlating these simulated vehicle paths with emission rates from the MOVES model. The study then applies a regression analysis to examine the connection between the increase in emissions and various influencing factors. The findings indicate that this approach efficiently reflects the impact of variables like accident duration, vehicle mix, and traffic volume on CO2 emissions across different lane configurations. The accuracy of these predictions is also confirmed. The outcomes suggest the model's potential usage in guiding efforts to lower emissions and determining the optimal duration of incident management, particularly in terms of lane closure, to mitigate emission impacts. This paper also discusses the limitations of the model and the future improvement direction.

Air pollution is a global issue, and the transportation sector is recognized as the third-largest contributor to anthropogenic greenhouse gas emissions. Vehicles emit a range of chemical compounds as a direct result of the combustion process. The nature and quantity of these emissions depend on the vehicle's characteristics, road, and local weather conditions. As a result, these emissions require special attention due to the adverse effects contributing to global warming and significantly impacting human health. In this regard, diagnosing and monitoring air quality is crucial for understanding the nature and quantity of emissions generated by various sources. However, in developing countries, the necessary inputs, and data for conducting such analyses are not always available. Therefore, the purpose of this study is to estimate emissions specifically generated from road operations. To achieve this, HDM-4 calculation tool is utilized to quantitatively estimate these emissions. This tool was applied in Baja California, Mexico, on the Centinela-La Rumorosa highway. The results obtained show that annually, 372.5 tons of pollutant emissions are generated, composed of HC, CO, CO2, NOx, Par, SO2, and PB, covering a mere 128 kilometers of length within a state road network spanning 11,429 kilometers. This highlights the necessity of implementing strategies to reduce emissions or the environmental impact generated by vehicular operations on roads in developing countries.

This paper presents a new implementation of a 2-box absolute flow model, enabling the calculation of CO₂ transfer between the atmosphere and a mixing reservoir representing the combined effect of the terrestrial and ocean regions. The model uses published values of anthropogenic CO₂ fossil fuel emissions (CO2ff), atmospheric CO₂ mixing ratio and nuclear weapons bomb yields, to compute atmospheric d¹³C and Δ¹⁴C time-series. The level of agreement between the calculated values and the accepted values for d¹³C is within ± 0.05 ‰, and for Δ¹⁴C is within ± 3‰, spanning 200 years. The model contains only seven internal parameters; these are varied to optimize the fit, leading to reasonable parameter values, indicating the validity of the method. In addition, the model shows how a rising CO₂ exchange influx fluctuating with surface temperature is compatible with a nett atmospheric CO₂ sink. The study demonstrates that a single CO₂ residence time applies to both the ¹⁴C bomb pulse and the anthropogenic flux, contrary to the conventional view that "bomb radiocarbon and anthropogenic CO₂ do not behave identically." [Joos 1994 Nature 370, 181–182]. It is shown that the difference in behaviour, claimed to be due to seawater chemistry, is not significant in practice since fluctuating bulk carbon dominates fluctuating isotopic ratio. A new analysis of the airborne fraction indicates that the assumption of a time-dependent exchange influx results in a similar residence time for bulk CO₂ as for ¹⁴C in the nuclear bomb pulse, reinforcing the view that the ¹²C, ¹³C and ¹⁴C carbon isotopic forms of CO₂ behave similarly in the carbon cycle.

Mass hauling operations play central roles in construction projects. They typically use many haulers that consume large amounts of energy and emit significant quantities of CO₂. However, practical methods for estimating the energy consumption and CO₂ emissions of such operations during project planning are lacking. This paper presents a detailed model for estimating the energy consumption and CO₂ emissions of mass haulers that integrates the mass hauling plan with a set of predictive equations. The mass hauling plan is generated using a planning program such as DynaRoad in conjunction with data on the productivity of selected haulers and the amount of material to be hauled during cutting, filling, borrowing, and disposal operations. This plan is then used as input for estimating the energy consumption and CO₂ emissions of the selected hauling fleet. The proposed model will help planners to assess the energy and environmental performance of mass hauling plans, and to select hauler and fleet configurations that will minimize these quantities. The model was applied in a case study, demonstrating that it can reliably predict energy consumption, CO₂ emissions, and hauler productivity as functions of the hauling distance for individual haulers and entire hauling fleets.

The way Norway is spearheading electrification in the transport sector is of global interest, and details of its policies and emission impacts represent a reference. We used the NERVE model, a bottom-up high-resolution traffic emission model, to calculate all exhaust emissions in Norway (2009-2020). This allows us to evaluate the co-benefit of policies to target climate change mitigation and air quality. We have analyzed local municipal data with regards to traffic growth, road network influences, vehicle composition, emissions and energy consumption. Light vehicle CO2 emissions per kilometre have been reduced by 22% since 2009, mainly driven by an increaseing bio-fuel mixing and BEV share. BEVs are mostly located in and around the main cities, areas with young vehicle fleets, and strong local incentives. Beneficiaries of all BEVs incentives have been a subset of the population with strong economic indicators. The incentivized growth in the share of diesel-fuelled passenger vehicle has been turned, and together with Euro6 emission standards, light vehicle NOx emissions have been halved since peaking in 2014. BEV represent an investment in emission reductions in years to come and current sales set up for an accelerated decline in emissions despite growth in traffic.

The increasing demand for energy, driven by technological advances, population growth, and economic expansion, has intensified the focus on efficient energy management. Tri-generation systems, such as Combined Cooling, Heating, and Power (CCHP) systems, are of particular interest due to their efficiency and sustainability. Integrating renewable energy sources like solar power with traditional fossil fuels further optimizes CCHP systems. This study presents a novel method for enhancing CCHP system efficiency by identifying optimal design parameters and assisting decision-makers in selecting the best geometric configurations. A mathematical programming model using the Harris Hawks optimizer was developed to maximize net power and exergy efficiency while minimizing CO2 emissions in a solar-assisted CCHP system. The optimization resulted in 100 Pareto optimal solutions, offering various choices for performance improvement. This method achieved higher net power output, satisfactory exergy efficiency, and lower CO2 emissions compared to similar studies. The study shows that maximum net power and exergy efficiency, with reduced CO2 emissions, can be achieved with a system having a low compression ratio and low combustion chamber inlet temperature. The proposed approach surpassed the response surface method, achieving at least a 4.2% reduction in CO2 emissions and improved exergy values.

Synergistic control of emissions of air pollutants and CO2 is critical to the dual challenges of air quality improvement and climate change in China. Based on the emission inventories of thermal power units in Beijing, Tianjin, and Hebei, this study analyzes the CO2 and NOX emission characteristics of these units, identifies and quantifies the synergistic drivers affecting these emission trends. Inventory data show that between 2010 and 2020, NOX emissions were reduced by 86.1%, while CO2 emissions were reduced by only 29.8%. Although significant progress has been made in reducing NOX emissions through measures such as end-of-pipe treatment, controlling CO2 emissions remains a difficult task. The index decomposition analysis reveals that economic growth is the main driver of CO2 and NOx emission growth, energy intensity reduction is the main driver of CO2 emission reduction, and end-of-pipe treatment is the main driver of NOX emission reduction. Currently, coal occupies about 87% of the energy consumption of thermal power units in the Beijing-Tianjin-Hebei, and remains the main type of energy for synergistic emissions, and the potential for emission reduction in the energy structure remains huge. For NOX emissions, it is expected that 90% of the reduction potential can be achieved through energy restructuring and end-of-pipe treatment. In conclusion, the high-precision unit-by-unit emission study confirms the effectiveness of the control policy for thermal power units in the region and provides some scientific reference for future policy formulation.

This study investigates the role of insulation, in commercial buildings and how it affects energy efficiency and sustainability in different climate regions. Commercial buildings consume an amount of energy making them ideal candidates for energy saving measures. Insulation plays a role in maintaining indoor conditions reducing energy usage and minimizing carbon emissions by limiting heat transfer through the building’s envelope. By conducting simulations using the Hourly Analysis Program (HAP) this research examines how insulation thickness, climate conditions and building characteristics impact energy consumption and greenhouse gas emissions. The study covers climate zones with a focus on Afghanistan, semi-arid, arid and mountainous regions where sustainable construction practices are highly important. The findings demonstrate that insulation has an effect on enhancing energy efficiency particularly when it comes to heating. Additionally, economic factors, future research directions and broader implications, for construction practices are thoroughly discussed. Considering that the construction industry contributes significantly to carbon emissions this research provides insights into promoting sustainable building practices. By optimizing insulation strategies, architects, builders and policymakers can reduce the impact of commercial buildings while advancing energy efficiency and supporting a more sustainable urban future.

Soil tillage intensity influences the distribution of nutrients, and soil’s physical and me-chanical properties, as well as gas flows. The impact of reduced tillage on these indices in spring barley cultivation is still insufficient and requires more analysis on a global scale. This study was carried out at Vytautas Magnus University, Agriculture Academy (Lithu-ania) in 2022–2023. The aim of the investigation was to determine the effect of the tillage systems on the soil temperature, moisture content, CO2 respiration and concentration in spring barley cultivation limited by the semi-humid subarctic climate. Based on a long-term tillage experiment, five tillage systems were tested: deep and shallow mold-board ploughing, deep cultivation-chiselling, shallow cultivation-chiselling, and no-tillage. Shallow ploughing technology was found to be better at conserving soil moisture and maintaining a higher temperature. Deep cultivation had a lower moisture content and lower soil temperature. Shallow cultivation fields in most cases increased CO2 emissions and CO2 concentration. The results show that in direct sowing fields, most cases had a positive effect on crop density. Direct sowing fields resulted in significantly lower grain yields of spring barley in the years studied.

Biochar application to soil has been proposed as a means for reducing soil greenhouse gas emissions and mitigating climate change. The effects, however, of interactions between biochar, moisture and temperature on soil CO₂ and N₂O emissions, remain poorly understood. Furthermore, the applicability of lab-scale observations to field conditions in diverse agroecosystems remains uncertain. Here we investigate the impact of a mixed wood gasification biochar on CO₂ and N₂O emissions from loess-derived soils using: (1) controlled laboratory incubations at three moisture (27, 31 and 35%) and three temperature (10, 20 and 30°C) levels, and (2) a field study with four cropping systems (continuous corn, switchgrass, low diversity grass mix, and high diversity grass-forb mix). Biochar reduced N₂O emissions under specific temperatures and moistures in the laboratory and in the continuous corn cropping system in the field. However, the effect of biochar on N₂O emissions was only significant in the field, and no effect on cumulative CO₂ emissions was observed. Cropping system also had a significant effect in the field study, with soils in grass and grass-forb cropping systems emitting more CO₂ and less N₂O than corn cropping systems. Observed biochar effects were consistent with previous studies showing that biochar amendments can reduce soil N₂O emissions under specific, but not all, conditions. The disparity in N₂O emission responses at the lab and field scales suggests that laboratory incubation experiments are not reliable for predicting the impact of biochar at the field scale.

CO₂ emissions have been identified as the main driver for climate change, with devastating consequences for the global natural environment. The steel industry is responsible for ca. 8%-11% of global CO₂ emissions, due to high fossil-fuel and energy consumption. The onus is therefore on industry to remedy the environmental damage caused and to decarbonise production. This desk research report follows a two-tiered route: 1) exploring the Bio Steel Cycle; 2) proposing a seven-step strategy to overcome the challenges within the iron and steel industry. The true levels of CO₂ emissions in the steelmaking process, during the blast-furnace/basic-oxygen-furnace operation, will be detailed first, at 4.61t of CO₂ emissions/t of steel produced. The manuscript proposes a solution for reduced carbon emissions steelmaking with the Bio Steel Cycle components and detail on how to reach net-zero carbon emissions steel production. The 7-step-implementation-strategy as a potential solution to achieve net and true zero carbon emissions steel production in the short to medium-term. The findings of this are pointing towards the conclusion that CO₂ emissions seem to have been under-reported and under-estimated in the past, but the emission can be addressed if the correct scenarios for net-zero steel manufacturing are implemented by 2050.

The study presents empirical results investigating the relationships among renewable and non-renewable energy consumption, CO2 emissions, and GDP within the Visegrád Group (V4) countries. Using FMOLS/DOLS and ARDL approaches, along with causality tests based on the Toda-Yamamoto method, the study explores these relationships at a regional level. The findings indicate that renewable energy has a small positive impact on long-term economic growth, with non-renewable energy having a more significant effect. Moreover, CO2 emissions have a negative impact on economic growth, suggesting ongoing reliance on non-renewable energy sources and a burden on economic expansion. On an individual country level, the effects vary. Poland, Slovakia, and Hungary exhibit a negative relationship between CO2 emissions and economic growth. Energy sources also differ in impact: in Poland, the Czech Republic, and Slovakia, non-renewable energy significantly affects economic growth, while in Hungary, renewable energy plays a more substantial role. Causality tests reveal a causal relationship between CO2 emissions and economic growth in the Czech Republic and Poland, suggesting CO2 emissions significantly influence economic expansion. In terms of energy production, renewable energy is causally related to economic growth in the Czech Republic and Slovakia. All countries demonstrate significant causality between non-renewable energy and economic growth. Additionally, a relationship between renewable energy and CO2 emissions is confirmed in Poland.

The environmental Kuznets curve (EKC) hypothesis posits an inverted U-shaped relationship between economic growth and environmental degradation. However, there is no consensus regarding the EKC hypothesis among countries and regions of different income groups. In this study, we analyze the EKC hypothesis for 158 countries and 44 regions from 1990 to 2020, categorizing them into different income groups based on the World Bank's income classification (low, lower-middle, upper-middle, and high-income countries). Our findings reveal mixed patterns in the EKC across different income levels, highlighting the heterogeneous relationship between economic growth and carbon emissions and showing differentiated patterns among different income levels. While a rise in income for high-income countries should be reflected in a shift toward fewer carbon emissions, for lower-income countries, growth is still associated with rising emissions. This underscores the urgent need for policy interventions that decouple economic development from environmental degradation. A balanced approach to economic growth, which prioritizes carbon neutrality across all stages of development, by tailoring environmental and economic strategies to address CO2 emissions effectively, should be adopted, recognizing the different developmental stages and income levels of countries and regions.

In this paper a dynamic relationship between the CO2 emissions in Finland, Norway and Sweden is presented. With the help of a VAR(2) model, and using the Granger terminology, it is shown that the emissions in Finland are affecting those in Norway and Sweden. Other aspects of this dynamic relationship are presented as well.

TThe number of supermarkets offering a grocery delivery has been increasing during the last years. Many studies deduce CO₂ emission savings using this concept. Since the delivery of groceries also consumes energy and produces emissions, break-even points can be calculated, from where the delivery has environmental advantages compared to the customer pickup. In this paper, influences of differing vehicle use on break-even points for savings of energy and CO₂ emissions are analyzed for the case of Haidhausen Süd, a city district of Munich in Germany. Internal combustion engine and electric vehicles are investigated to depict current as well as future trends. After an introduction to the used methodology, the potential to save energy and CO₂ emissions related to the delivery of groceries in the chosen district of Munich is evaluated. Afterwards, influences on the break even points are presented and discussed. As the results show, a delivery of groceries leads to energy and carbon dioxide savings in a wide range of private vehicle use for grocery shopping trips. Nevertheless, if the complete customer vehicle fleet is electrified, the use of delivery vehicles with an internal combustion engine can cause an additional environmental impact at the current modal split for shopping trips in Germany.

This study analyzes the effects of primary energy consumption and alternative energy patents on CO2 emission intensity and CO2 emissions per capita, and their relationship using canonical correlation analysis. Our results are as follows. First, CO2 emissions from natural gas and liquefied petroleum gas have positive effects, while CO2 emissions from gasoline, fuel oil, diesel, and kerosene have negative effects on CO2 emission intensity. Second, patents for devices for producing mechanical power from muscle energy have large positive effects. Finally, the more the patents use waste heat, geothermal energy, hydro energy, and wind energy, the higher the CO2 emissions from liquefied petroleum gas, gasoline, and crude oil and the lower the CO2 emissions from diesel, which are conducive to controlling CO2 emissions. Therefore, energy policies will be more effective based on the CO2 “emissions” level from primary energy consumption and the “control” degree of CO2 emissions by alternative energy.

rdinary people and political leaders must know the sources of greenhouse gas emissions and their effect on global climate change before they have ability to make decisions to reduce emissions and increase sinks of these gases. These people must, however, understand where greenhouse gas emissions are formed and how reductions can be made: they must understand where carbon dioxide sinks are and how to preserve or increase these sinks. North Savo is the example used in this work to describe the present emissions and sinks. There are proposals on what should and could be done to reduce greenhouse gas emissions caused by traffic, heating, forests and agriculture. There are possibilities of reducing emissions of greenhouse gases in traffic and heating in spite of the fact that the province has a low population density with long distances between homes and workplaces and schools, and a cold climate. We believe that research will also find solutions for reducing greenhouse gases and protecting waters, which are used for recreational purposes and for raw water of drinking water in many places. Luckily forests cover large areas of North Savo and their growth is an important carbon dioxide sink. In addition, forest soils serve as a valuable storage of carbon. Besides carbon dioxide emissions, emissions of nitrous oxide and methane must also be considered since they are more potent greenhouse gases than carbon dioxide and land use can thus influence these gas emissions.

Laboratory experiments were performed to measure the supercritical CO2 (scCO2) storage ratio (%) of the conglomerate and sandstone in Janggi Basin, which are classified as rock in Korea available for CO2 storage. The scCO2 storage capacity was evaluated by direct measurement of the scCO2 amount replacing pore water in a reservoir rock core. The scCO2 sealing capacity of the cap rock (i.e., tuff and mudstone), was also compared by measuring the initial scCO2 seepage pressure (Δp) into the rock core. The measured average scCO2 storage ratio of the conglomerate and the sandstone in Janggi Basin was 30.7 % and 13.1 %, respectively, suggesting that the scCO2 storage capacity is greater than 360,000 metric tons in the Janggi Basin. The initial scCO2 seepage pressure of the tuff in the Janggi Basin was 15 bar and continuous scCO2 injection into the tuff core occurred at Δp higher than 20 bar. For the mudstone, the initial scCO2 seepage pressure was higher than 150 bar (10 times higher than that of the tuff), demonstrating that the mudstone is more suitable than the tuff to shield scCO2 leakage from the reservoir rock in the Janggi Basin.

Human-caused anthropogenic greenhouse emissions impact climate globally. In this pilot study, we aim to reveal the impact of oil and gas emissions from local oil deposits in the regime of their natural degradation and development and eco-physiological changes of pine forests in Tatarstan Republic, Russia over the past century. We performed stable carbon isotope analysis in pine tree rings (13Cptrw) to reveal the impact of oil and gas emissions from the giant oil field reservoirs located in Leninogorsk region (UVRT) and the natural reserve site in Raifa. Our results show decreasing 13Cptrw at UVRT in 1943 when oil extraction was started, and in 1970, when it reached the maximum production. We found that 13Cptrw from UVRT indicates on developing unfavourable drier conditions and suppressed tree growth caused by both human-induced oil and deposit infrastructure and natural processes compared to undisturbed Raifa. The 13Cptrw from Raifa is more negative compared to UVRT, which can be explained by higher forest sensitivity to human-induced impact. From an ecophysiological point of view decreasing intercellular to ambient CO2 concentration at the leaf level and increasing intrinsic water use efficiency along with decreasing tree-ring width at UVRT (1970-2021) indicate on development of drought conditions.

To understand dynamics in climate change, informing policy decisions and prompting timely action to mitigate its impact, this study provides a comprehensive analysis of the short-term trend of year-on-year CO2 emission changes across ten countries, considering a broad range of factors including socioeconomic, CO2-related industry, and education. This study uniquely goes beyond the common country-based analysis, offering a broader understanding of the interconnected impact of CO2 emissions across countries. Our preliminary regression analysis, using the ten most significant features, could only explain 66% of variations in the target. To capture emissions trend variation, we categorized countries by the change in CO2 emission volatility (high, moderate, low with upward or downward trends), assessed using standard deviation. We employed machine learning techniques, including feature importance analysis, Partial Dependence Plots (PDPs), sensitivity analysis, and Pearson and Canonical correlation analyses, to identify influential factors driving these short-term changes. The Decision Tree Classifier was the most accurate model, with an accuracy of 96%. It revealed population size, CO2 emissions from coal, the three-year average change in CO2 emissions, GDP, CO2 emissions from oil, education level (incomplete primary), and contribution to temperature rise as the most significant predictors, in order of importance. Furthermore, this study estimates the likelihood of a country transitioning to a higher emission category. Our findings provide valuable insights into the temporal dynamics of factors influencing CO2 emissions changes, contributing to global efforts to address climate change

CO2 injection into geological formations is considered one way of mitigating the increasing levels of carbon dioxide concentrations in the atmosphere and its effect on and global warming. In regard to sequestering carbon underground, different countries have conducted projects at commercial scale or pilot scale and some have plans to develop potential formations for carbon dioxide storage. In this study, pure CO2 injection is examined on a model with the properties of bunter sandstone and then sensitivity analyses were conducted for some of the important parameters. The results of this study show that the extent to which CO2 has been convected in the porous media in the reservoir plays a vital role in improving the CO2 dissolution in brine and safety of its long term storage. We conclude that heterogeneity plays a crucial role on the saturation distribution and can increase or decrease the amount of dissolved CO2 in water. Furthermore, the value of absolute permeability controls the effect of the Kv/Kh ratio on the CO2 dissolution in brine. In other words, as the value of vertical and horizontal permeability decreases (i.e. tight reservoirs) the impact of Kv/Kh ratio on the dissolved CO2 in brine becomes more prominent. Additionally, reservoir engineering parameters, such as well location, injection rate and scenarios, also have a high impact on the amount of dissolved CO2.

The direct hydrogenation of greenhouse gas carbon dioxide (CO2) to higher alcohols (C2+OH), as an important research area in C1 chemistry, is one of the most essential approaches to convert CO2 into liquid fuels or other value-added chemicals. The high atom economy and direct pathway make this reaction attractive to convert CO2 to higher alcohols. However, due to the complicated reaction network and the difficulty of C-C coupling, the formation of higher alcohols is more difficult compared with methanol or other compounds containing one carbon. The key issue is development of novel catalysts with high conversion and space time yield. But this is still a huge challenge faced by researchers. In this review, the thermodynamics and reaction pathways of CO2 hydrogenation were firstly clarified. Subsequently, after reviewing single metal-based, bi-and multi-metallic catalysts, the recently progress of tandem catalytic system was emphasized. Finally, we also provided an overview about tandem catalysis for CO2 hydrogenation to higher alcohols.

Although total nett CO₂ atmospheric flow can be estimated with reasonable accuracy, the contributing gross fluxes between the atmosphere and the earth's surface are poorly understood. This paper presents a method, driven by the objective of simplicity, by which the global outflow and inflow of CO₂ between atmosphere and a globally equivalent "mixing reservoir" can be estimated, using the isotopes ¹⁴C and ¹³C as tracers. It has been asserted that the isotopic carbon in CO₂ cannot be directly used as a tracer in flow studies because it is not subject to the Revelle factor. Evidence is provided showing that this view is mistaken. The model contains 7 key parameters which are used to create synthetic records of Δ¹⁴C and d¹³C spanning 200 years or more, including during the period of atmospheric weapons testing and its decay known as the "bomb pulse". By optimising the fit between these computed values and the historical records of d¹³C and Δ¹⁴C, all seven key parameters are determined. The effective "mixing reservoir" is thereby determined to have a size around six times that of the atmosphere, with global outflux rising from 39.7 GTC yr-1 in 1750 to 58.9 GTC/yr in 2020, this figure probably not including annually cycled carbon.

Special preparation of SBA-15 materials has been carried out for creating adsorbents exhibiting an enhanced and selective adsorption toward CO2. This creation starts from an adequate conditioning of the silica surface, via a thermo-alkaline treatment to increase the population of silanol species on it. CO2 adsorption is only reasonably achieved when the SiO2 surface becomes aminated after put in contact with a solution of an amino alkoxide compound in the right solvent. Unfunctionalized and amine-functionalized substrates were characterized through X-ray diffraction, N2 sorption, Raman spectroscopy, electron microscopy, 29Si solid-state NMR, and NH3 thermal programmed desorption. These analyses proved that the thermo-alkaline procedure desilicates the substrate and eliminates the micropores (without affecting the SBA-15 capillaries), present in the original solid. NMR analysis confirms that the hydroxylated solid anchors more amino functionalizing molecules than the unhydroxylated material. The SBA-15 sample subjected to hydroxylation and amino- functionalization displays a high enthalpy of interaction, a reason why this solid is suitable for a strong deposition of CO2 but with the possibility of observing a low-pressure hysteresis phenomenon. Contrastingly, CH4 adsorption on amino-functionalized, hydroxylated SBA-15 substrates becomes almost 5 times lesser than the CO2 one, thus giving proof of their selectivity toward CO2.

A single geological carbon dioxide (CO2) storage within salinity aquifer as a paramount stratagem in the context of forthcoming CO2 sequestration initiatives. Within the expansive tapestry of terrestrial salinity aquifers in China, replete with nuances in mineral composition and structural diversity, a paradigm distinct from the marine sedimentary basins of North America, a labyrinthine stratigraphic environment of elevated complexity unfolds. Consequently, conspicuous lacunae and insufficiencies manifest within the existing knowledge reservoir pertaining to CO2-water-rock (mineral) reaction mechanisms. Notably, a conspicuous dearth of insights prevails concerning the dissolution kinetics inherent to individual minerals embroiled in these reactions. The present investigation undertakes a scrupulous exploration into the dissolution and erosive processes manifest within four emblematic terrestrial minerals in conjunction with CO2. Furthermore, the study meticulously scrutinizes the evolution of ionic composition and pH within the formation water throughout the trajectory of the geochemical reactions. To accomplish this, a simulation apparatus is configured to emulate conditions germane to temperature, pressure, and mineralization characteristics characteristic of a prototypical salinity aquifer reminiscent of the Daqing oilfield in China. The findings that emerge from this scrutiny reveal that the erosive action of CO2 fluid begets varying degrees of dissolution within the four minerals under investigation. Moreover, our meticulous inquiry lays bare that, in the terminal phases of the reaction process, feldspar precipitates secondary minerals, characterized primarily by dawsonite, in response to the aquatic milieu typifying the profound salinity stratum of terrestrial sedimentation. This milieu is notably enriched with Na+ ions and NaHCO3. This phenomenon suggests that feldspar, under these specific conditions, assumes the mantle of a mineral amenable to carbon sequestration, thus enriching the reservoir for CO2 mineralization within the salinity stratum of terrestrial sedimentation.

Site environments and instrumental characteristics of carbon dioxide (CO₂) measurements operated by local governments in the Kanto Plain, the center of which is Tokyo were summarized for this study. The observation sites were classified into environments of three types: urban, suburban, and woodland. Based on a few decades of accumulated hourly data, the diurnal and seasonal variations of CO₂ concentrations were analyzed as a composite of anomalies from annual means recorded for each site. In urban areas, the highest concentrations appear before midnight in winter. The second peak corresponds to the morning rush hour and strengthening of the inversion layer. Suburban areas can be characterized as having the highest concentration before dawn and the lowest concentration during the daytime in summer in association with the activation of respiration and photosynthesis of vegetation. In these areas, concentration peaks also appear during the morning rush hour. Woodland areas show background features, with the highest concentration in early spring: higher than the global background by about 5 ppmv.

Mn-promoted bulk iron catalysts with high specific surface area (82-211 m2.g-1) were synthesized by coprecipitation followed by drying under supercritical conditions. The catalysts were tested in the CO2 hydrogenation reaction. The Mn-promoted iron catalysts showed better textural properties than the bare Fe2O3 catalyst, allowing better dispersion of the active phase, easier reduction of iron oxide, better carburization of iron oxides and higher catalytic activity than the bare Fe2O3 catalyst. The best activity results were obtained by catalyst promotion with a very low amount of Mn (Mn/Fe ratio of 0.05). Upon steady-state conditions (T=340 ºC, total pressure of 20 bar and H2/CO2=3), this catalyst showed high CO2 conversion (44.2%) and selectivity to C2-C4 hydrocarbons (68%, olefin to paraffin ratio of 0.54), while the selectivity to C5+ hydrocarbons, CH4 and CO was about 3.2, 38.5 and 5%, respectively. A close correlation was found between catalyst textural properties and CO2 conversion. The most active MnFe-0.05 catalyst shows high stability during 72 h of reaction related to low amount of soft coke formation and catalyst activation through the formation of χ-Fe5C2 phase during the on-stream reaction.

Biogas contains more than 40% CO2 that can be removed to produce high quality CH4. Recently, CH4 production from CO2 methanation has been reported in several studies. In this study, CO2 methanation of biogas was performed over a 20 wt% Ni-Mg-Al catalyst, and the effects of CO2 conversion rate and CH4 selectivity were investigated as a function of CH4, O2, H2O, and N2 compositions of the biogas. At a gas hourly space velocity (GHSV) of 30,000/h, the CO2 conversion rate was ~79.3% with a CH4 selectivity of 95%. In addition, the effects of the reaction temperature (200–450 °C), GHSV (21,000–50,000/h), and H2/CO2 molar ratio (3–5) on the CO2 conversion rate and CH4 selectivity over the 20 wt% Ni-Mg-Al catalyst were evaluated. The characteristics of the catalyst were analyzed using Brunauer-Emmett-Teller (BET) surface area analysis, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). The catalyst was stable for approximately 200 h at a GHSV of 30,000/h and a reaction temperature of 350 °C. CO2 conversion and CH4 selectivity were maintained at 75% and 93%, respectively, and the catalyst was therefore concluded to exhibit stable activity.

As the major greenhouse gas, CO2 gas emission has been noticeably increased over the past decades resulting in global warming and climate change. As a result, it is imperative to reduce the excess CO2 in the atmosphere to hold “the increase in the global average temperature to well below 2°C (ideally 1.5°C) above pre-industrial levels set by the Paris Agreement on climate change. Among many ways, CO2 capture technology is considered as the most promising technology among the available technologies. Porous materials such as carbons, silica, zeolites, hollow fibers, and alumina are widely used as CO2 sorbents. However, among the available porous sloid sorbents, porous silica-based materials grabbed a significant attention due to their unique properties including high surface area, pore volume, good thermal and mechanical stability, and low cost. Therefore, development of porous silica materials as a promising CO2 absorbent is a continuously expanding research area in the current moment. Herein, we aim to visualize a full picture of the porous silica-based materials for CO2 capture. This review presents a comprehensive study of existing CO2 capture techniques and highlights the recent progress of different porous silica materials and synthesis processes. CO2 adsorption capacities of unmodified porous silica materials are less effective as compared with functionalized silica materials. Various research activities have been reported about functionalization of pours silica using amine groups. Therefore, in this review, different synthesis routes of amine-functionalized porous silica materials, CO2 adsorption capacities, gas selectivity and reusability were discussed. Moreover, the research challenges associated with the porous silica materials and future research directions are summarized.

Geological storage of carbon dioxide (CO2) is a crucial technology for mitigating global temperature rise. Near-depleted edge-bottom water reservoirs are attractive targets for CO2 storage, as they can not only enhance oil recovery (EOR) but also provide important potential candidates for geological storage. This study investigated CO2 enhanced oil recovery and storage for a typical near-depleted edge-bottom water reservoir that had been developed for a long time with a recovery factor of 51.93%. To improve the oil recovery and CO2 storage, new production scenarios are explored. At the near-depleted stage, by comparing the four different scenarios of water injection, gas injection, water alternating gas injection, and bi-directional injection, the highest additional recovery of 8.64% is achieved by the bi-directional injection scenario. Increasing the injection pressure leads to a higher gas-oil ratio and liquid production rate. After shifting from the near-depleted to depleted stage, the most effective approach to improve CO2 storage capacity is to increase reservoir pressure. At 1.4 times the initial reservoir pressure, the maximum storage capacity is 6.52×108 m3. However, excessive pressures boosting poses potential storage and leakage risks. Therefore, lower injection rates and longer intermittent injections are expected to achieve a larger amount of long-term CO2 storage. Through the numerical simulation study, a gas injection rate of 80,000 m3/day and a schedule of 4-6 years injection with 1 year shut-in was shown to be effective for the case considered. During 31 years of CO2 injection, the percentage dissolved CO2 increased from 5.46% to 6.23% during the near-depleted period, and to 7.76% during the depleted period. This study acts as a guide for the CO2 geological storage of typical near-depleted edge-bottom water reservoirs.

This study explores the stability of electrodeposited copper catalysts utilized in electrochemical CO2 reduction (ECR) across various amine media. The focus is on understanding the influence of different amine types, corrosion ramifications, and the efficacy of pulse ECR methodologies. Employing a suite of electrochemical techniques including potentiodynamic polarization, linear resistance polarization, cyclic voltammetry, and chronopotentiometry, the investigation reveals useful insights. The findings show that among the tested amines, CO2-rich monoethanolamine (MEA) exhibits the highest corrosion rate. However, in most cases the rates remain within tolerable limits for ECR operations. Primary amines, notably monoethanolamine (MEA), show enhanced compatibility with ECR processes, attributable to their resistance against carbonate salt precipitation and sustained stability in potential over extended durations. Conversely, tertiary amines such as methyldiethanolamine (MDEA) present challenges due to the formation of carbonate salts during ECR, impeding their effective utilization. The study highlights the effectiveness of pulse ECR strategies in stabilizing ECR. A noticeable shift in cathodic potential and reduced deposit formation on the catalyst surface through periodic oxidation underscores the efficacy of such strategies. These findings offer insights for optimizing ECR in amine media, thereby providing promising pathways for advancements in CO2 emission reduction technologies.

A novel gas-phase electrocatalytic system based on a low-temperature proton exchange membrane (Sterion) was developed for the gas phase electrocatalytic conversion of CO2 to liquid fuels. This system achieved gas-phase electrocatalytic reduction of CO2 at low temperatures (below 90 ºC) over a Cu cathode by using water electrolysis-derived protons generated in-situ on an IrO2 anode. Three Cu-based cathodes with varying metal particle sizes were prepared by supporting this metal on an activated carbon at three loadings (50, 20, and 10 wt%; 50%Cu-AC, 20%Cu-AC, and 10%Cu-AC, respectively). The cathodes were characterized by N2 adsorption–desorption, temperature-programmed reduction (TPR), and X-ray diffraction (XRD) whereas their performance towards the electrocatalytic conversion of CO2 was subsequently studied. The membrane electrode assembly (MEA) containing the cathode with the largest Cu particle size (50%Cu-AC, 40 nm) showed the highest CO2 electrocatalytic activity per mole of Cu, with methyl formate being the main product. This higher electrocatalytic activity was attributed to the lower Cu–CO bonding strength over large Cu particles. Different product distributions were obtained over 20%Cu-AC and 10%Cu-AC, with acetaldehyde and methanol being the main reaction products, respectively. The CO2 consumption rate increased with the applied current and the reaction temperature.

There is need to accurately design pipelines to transport the expected increase of CO₂ captured from industrial processes after the signing of the Paris Climate Agreement in 2016. This paper reviews several aspects of CO₂ pipeline design with emphasis on pressure drop and models for the calculation of pipeline diameter. Two categories of pipeline equations were identified. The first category is independent of pipeline length and has two different equations. This category is used to specify adequate pipeline diameter for the volume of fluid transported. The optimum economic pipe diameter equation (Eq. 17) with nearly uniform resultant velocity values at different flow rates performed better than the standard velocity flow equation (Eq. 20). The second category has four different equations and is used to calculate pipeline pressure drop or pipeline distance for the installation of booster stations after specifying minimum and maximum pipeline pressures. The hydraulic equation is preferred because it gave better resultant velocity values and the closest diameter value obtained using Aspen HYSYS (V.10) simulation. The effect of impurities on the pressure behaviour and optimal pipeline diameter and pressure loss due to acceleration were ignored in the development of the models. Further work is ongoing to incorporate these effects into the models.

This study explores pressure, miscibility, and pore medium effects on heavy hydrocarbon recovery up to 65 MPa from four rock types: sand, tight sandstone, cavernous limestone, and oil sand. Results reveal MMP at 50 MPa, with peak recovery at 93% (56 MPa). Interestingly, recovery trends counter traditional expectations, notably decreasing in tight sandstone (42-56 MPa) and oil sand (50-65 MPa). Varied recoveries in cavernous limestone (25-56 MPa) highlight porosity and vug influence. Higher pressures hinder recovery due to SC-CO2's density and viscosity, favoring the immiscible process for efficient heavy hydrocarbon extraction.

As the need to minimize environmental impact continues to rise, it is essential to incorporate, advance, and adopt renewable energy sources and materials to attain climate neutrality. It is established that economic growth is built upon infrastructure where cement industry plays a crucial role. However, it is also known that this industry is actively looking for ways to transition towards low-carbon practices to encourage sustainable and environmentally conscious practices. To this end, the use of refused derived fuels to substitute fossil fuels is very appealing, as these present the potential to lower the clinker production costs and CO2 emissions. Bearing this in mind, the primary objective of this work is to gain insights of the combustion behavior in an industrial rotary kiln, studying real-life scenarios and assessing the potential of substituting alternative fuels for fossil fuels to reduce CO2 emissions. A 3D CFD turbulent combustion model was formulated in Ansys® considering a Pillard NOVAFLAM® burner, where refused derived and petcoke fuels were used and different secondary air mass flows were considered. From the obtained results it was possible to conclude that the outcome of the combustion process is greatly influenced by the fuel-to-air ratio. Increasing the secondary air mass flow promotes the occurrence of a complete and efficient combustion process, leading to an enhanced fuel conversion and decreased formation of pollutants as CO, soot, and unburnt hydrocarbons.

A new process is reported for the incorporation of a fluoropolymer into a solid perovskite film. Poly(trifluoroethyl methacrylate) [CH2C(CH3)(CO2CH2CF3)]n was delivered to methylammonium lead iodide (CH3NH3PbI3) perovskite films by crystallizing the film in supercritical carbon dioxide/ethanol containing the dissolved fluoropolymer. The surface was characterized before and after fluoropolymer exposure using scanning electron microscopy, Raman spectroscopy and contact angle measurements. The results indicate that the fluoropolymer was incorporated into the perovskite film during the supercritical fluid crystallization process.

Carbon capture and storage has gotten increased attention during the last decade, and several full-scale projects are currently being planned. This requires transportation of large quantities of CO2 from the capturing plant to the end point. From economic and public acceptance point of view it is important to ensure that the transportation system is operated in a safe manner. Thus, avoiding threats like corrosion or formation of particles are important. It is therefore required to monitor that the transported CO2 fulfils the required specifications, and in practice this means that the impurity content of the CO2 must be analysed. CO2 will in most cases be transported in the liquid or supercritical state (high pressure), which makes the practicalities around chemical analysis more difficult. Phase transition from liquid or supercritical state to gaseous state may also introduce several physiochemical effects that may affect the analysis. This paper discusses technical and practical challenges with such types of analysis. Most of this work is based on experience that was gained during development of analytical system for dense phase CO2 in a joint industry project that studied corrosion and chemical reactions in a simulated CO2 transport system.

Investigation into geological storage of CO2 is underway at the Technology Development Plant (TDP) at Hontomín (Burgos, Spain), the only current onshore injection site in the European Union. The storage reservoir is a deep saline aquifer located within Low Jurassic Formations (Lias and Dogger), formed by fractured carbonates with low matrix permeability. Understanding the processes involved in CO2 migration within this kind of low-primary permeability carbonates influenced by fractures and faults is key to ensure safe operation and reliable plume prediction. During the hydraulic characterization tests, 2300 tons of liquid CO2 and 14000 m3 of synthetic brine were co-injected on site in various sequences to characterize the pressure response of the seal-storage pair [de Dios et al, 2017] The injection tests were analyzed with a compositional dual media model which accounts for both temperature effects (as the CO2 is liquid at the bottom of the wellbore) and multiphase flow hysteresis (to effectively simulate the alternating brine and CO2 injection tests that were performed). The pressure and temperature responses of the storage formation were history-matched mainly through the petrophysical characteristics of the fracture network [Le Gallo et al, 2017]. The dynamic characterization of the fracture network dominates the CO2 migration while the matrix does not appear to significantly contribute to the storage capacity. This initial modeling approach was improved using the characterization workflow developed within the European FP7 CO2ReMove project for sandstone fractured reservoirs [Ringrose et al., 2011; Deflandre et al., 2011]. Fractured reservoirs are challenging to handle because of their high level of heterogeneity that conditions the reservoir behaviour during the injection. In particular, natural fractures have a significant impact on well performance [Ray et al, 2012]. Furthermore, the understanding of the processes involved in CO2 migration within relatively low-permeability storage influenced by fractures and faults is essential for enabling safe storage operation [Iding and Ringrose, 2010]. As part of the European H2020 ENOS project, the site geological model is updated by integration of the recently acquired data such as the image log interpretations from injection and observation wells. The geological model is generated through the analysis and integration of data including borehole images and well test data. Following a methodology developed for naturally fractured hydrocarbon reservoirs [Ray et al., 2012], the image log analysis identified two sets of diffuse fractures. A Discrete Fracture Network [Bourbiaux et al., 2005] was built around both wells which encompass the caprock, storage and underburden formations. The fracture characteristics of the two sets of diffuse fractures, such as orientations, densities and conductivities, are calibrated upon the interpretation of the injection tests [Le Gallo et al, 2017]. For each facies, the DFN characteristics were then upscaled and propagated to the full-field reservoir simulation model as 3D fracture properties (fracture porosity, fracture permeability and equivalent block size).

Developing cost-efficient systems for transporting CO2 is key to accelerate the deployment of carbon capture and storage. The present work explores the impact of reducing the pressure of tank-based inland and at-sea transport on their techno-economic performance. The study uses established techno-economic models for CO2 transport, adjusted with the most up-to-date knowledge on costs of low-pressure containment and transport. Particularly, the impact of cargo tank material and design on the transport costs shows that low-pressure cargo tank systems can be 50% less expensive than medium-pressure systems if materials with similar price and strength can be used. This results in reductions in transport costs as high as 30% for long distances. This is partly driven by the currently suggested size limitation on medium-pressure shipping which limits its economies of scale. If this limitation is alleviated, the cost advantage of low-pressure shipping compared to medium-pressure is more limited (10-20%) although it remains advantageous. The same scaling effects on capacity were not found for truck and barge inland transport, thus yielding 1-10% cost reductions of low- relative to medium-pressure transport. These results imply that future systems may combine medium-pressure inland and low-pressure at-sea transport, and that efficient solutions connecting the two must be investigated.

The environmental aerosols in major South Asian cities were characterized using Aerosol Robotic Network datasets. Various types of aerosols were identified and classified. Industrial urban/vehicle emissions and biomass burning carbonaceous aerosols dominated during the winter, whereas dust aerosols dominated during the summer and pre-monsoon seasons, respectively. Moreover, mixed aerosol types existed throughout the year. An attempt has been made to detect carbonaceous aerosol CO2 using Zn-decorated ZnO nanocages, which can be converted into CH3OH and H2O via the use of H2 molecules. The adsorption of Zn on the nanocage of ZnO reduced the band width to 2.18 eV from 4.05 eV, with an increase in the room temperature sensitivity and a sensing response of −49.38% and −91.9%, respectively. The emergence of intermediate states near the Fermi level narrowed the bandgap. The negative electronegativity and electron affinity suggest the polar nature, high reactivity, and softness of the Zn-decorated ZnO CO2 complexes. Furthermore, a minimal recovery time of 2.249 × 10−11 s was noticed at room temperature, highlighting the remarkable catalytic efficiency of the ZnO-Zn/CO2 system compared with that of previously published Ag-decorated ZnO nanocages. An increase in temperature has minimal effects on the sensing response, while the recovery time decreased notably. This research was conducted within the context of density functional theory.

TiO2-supported Pd-NPs based materials were prepared following two distinct approaches: for the first set of materials 1-8, modification of the TiO2 support was performed prior to Pd NPs deposition while the 2nd set (9-15) was synthesized by deposition of modifiers over pre-synthesized Pd-PPh3/TiO2. These catalysts were applied in the hydrogenation of CO2 to formate and their performance compared with that of the unmodified Pd-PPh3/TiO2. Modification of the TiO2 support by organosilanes provided a beneficial effect in catalysis compared with the catalyst containing unmodified TiO2 or TiO2 modified by organophosphonic acids. In contrast, in most cases, the deposition of modifiers over previously synthesized Pd NPs supported on TiO2 was not beneficial to the activity of the catalyst. Interestingly, upon recycling, the first set of catalysts suffered a rapid decrease in activity while the anchoring of modifiers over previously formed Pd NPs showed an improved stability (TON > 500 after the 3rd recycling).

Given the imperative of security, sustainability of supply, strategic considerations, and energy independence, there is a widely acknowledged need to persist in utilizing coal as the primary fuel for electricity generation in power plants. However, in order to combat the rising levels of CO2 in the atmosphere, it is crucial to advance the development of carbon capture and storage (CCS) technologies that enable fossil fuel power plants to achieve zero emissions. These technologies play a pivotal role in capturing and effectively storing CO2, thus ensuring that coal-based power generation can continue while significantly reducing its environmental impact. By implementing CCS solutions, fossil fuel power plants can transition towards a more sustainable and environmentally friendly energy future.The utilization of chemical solvents for CO2 absorption, coupled with long-term storage, presents an intriguing and commercially viable technology for CO2 capture. However, the significant energy demands of the solvent regeneration process necessitate optimization, particularly in large-scale power plants. While the current cost of CO2 capture stands at approximately #55,000.00(Naira) per ton of CO2, the objective is to reduce this cost to below #25,000.00(Naira) per ton of CO2. This reduction in cost is essential to ensure the economic feasibility and widespread adoption of CO2 capture technologies in power generation.This research paper explores various approaches to address the energy demands associated with amine scrubbing integration in a commercial power plant. It provides a comprehensive analysis, both technically and economically, of the performance of these different approaches. While some of the proposed schemes may result in minor efficiency reductions, the key objective is to calculate the specific cost per ton of CO2 captured. The primary focus is on identifying the most suitable configuration to implement large-scale, cost-effective schemes that can serve as a foundation for CO2 capture demonstration projects. By determining the optimal configuration, this research aims to pave the way for the successful implementation of efficient and economically viable CO2 capture technologies in the power generation sector.

"Hydrogen is an extremely promising energy carrier, poised to become a commercially viable product in the coming years. However, there are significant hurdles that need to be addressed. One such challenge is the high energy consumption during the electrolysis process, which is used to produce hydrogen. Furthermore, the co-production of CO and CO2 during steam hydrocarbon reforming adds to the complexity. Finding innovative solutions to these issues is crucial for the widespread adoption of hydrogen as a clean and efficient energy source." Simultaneously, various industries have the capability to generate hydrogen as a by-product, each with differing levels of purity. For instance, sodium and chlorine production plants have the potential to produce high-purity hydrogen. On the other hand, digester and sewage gas can yield low-purity hydrogen. In both instances, there is an economic incentive to utilize this hydrogen for energy production or to inject it into existing natural gas pipelines A brief estimation of the technical potential of utilizing hydrogen from various sources in Nigeria, specifically for fuel cell usage, has been conducted. Moreover, resource potential visualization maps have been generated to help visualize the availability and distribution of these hydrogen sources throughout the country.

Microbial community succession in raw milk determines its quality and storage period. In this study, carbon dioxide (CO2) at 2000 ppm was used to treat raw milk to investigate the mechanism of extending the shelf life of raw milk by CO2 treatment from the viewpoint of microbial colonies and metabolites. The results showed that the shelf life of CO2-treated raw milk was extended to 16 days at 4 ℃, while that of the control raw milk was only 6 days. Microbiomics analysis identified 221 Amplicon Sequence Variants (ASVs) in raw milk, and the alpha diversity of microbial communities increased (P < 0.05) with the extension of storage time. Among them, Pseudomonas, Actinobacteria and Serratia were the major microbial genus responsible for the deterioration of raw milk, with a percentage of 85.7%. A combined metagenomics and metabolomics analysis revealed that microorganisms altered the levels of metabolites, such as pyruvic acid, glutamic acid, 5'- cmp, arginine, 2-propenoic acid, and phenylalanine in the raw milk through metabolic activities, such as ABC transporters, pyrimidine metabolism, arginine and proline metabolism and phenylalanine metabolism, and reduced the shelf life of the raw milk. CO2 treatment prolonged the shelf life of the raw milk by inhibiting the abundance of Gram-negative aerobic bacteria, such as Acinetobacter guillouiae, Pseudomonas fluorescens, Serratia liquefaciens and Pseudomonas simiae.

In today's society, mankind is confronted with two major problems: the energy crisis and the greenhouse effect. The artificial photosynthesis can use solar energy to convert greenhouse gas CO2 into high-value compounds, which is an ideal solution to alleviate the energy crisis and solve the problem of global warming. The combination of ZnO and polythiophenes (PTh) can make up for each other's drawbacks, thus improving the photoresponse behavior and separation efficiency of photogenerated carriers. PTh layer can transfer photogenerated electrons to ZnO, thereby extending the lifetime of photogenerated charges. The production rate of CH4 from photoreduction of CO2 with ZnO/PTh10 is 4.3 times that of pure ZnO, and the selectivity of CH4 is increased from 70.2% to 92.2%. The conductive PTh can absorb photons to induce π–π* transition, the photogenerated electrons can transfer from LUMO to the conduction band (CB) of ZnO, thus more electrons involve in the reduction of CO2.

ChatGPT is an AI language model trained on vast amounts of text data, including scientific papers, providing a comprehensive understanding of catalysis. However, its reliability in catalysis research is unknown. To evaluate reliability, we compared a ChatGPT-generated review article on heterogeneous catalysts for higher alcohols synthesis by CO₂ hydrogenation to published peer-reviewed papers. Although the ChatGPT review article covers most necessary parts, it lacks sufficient discussion of the reaction mechanism. The core sections are too general, being not specific enough to the topic, and contain errors. The lack of citations further increases unreliability. While ChatGPT can provide much content on catalysis, it is insufficient and inaccurate for research on specific topics.

The increase in global warming due to NOx, CO2, and CH4 harmfully different ecosystems and significantly prejudice world life. A promising methodology in this sense is the pollutant conversion into valuable chemicals from photocatalytic processes by reusable photocatalyst. In this way, the present work aimed to produce a Nb2O5 photocatalyst nanofibers system to convert CO2 by the electrospinning method. Based on the collected data, the nanofibers calcination at 600°C for 2 h resulted in the best condition to obtain a homogeneous surface with an average diameter of 84 nm. As a result, the Nb2O5 nanofibers converted CO2 mostly into CO and CH4, reaching values around 8.5 μmol g−1 and 0.55 μmol g−1, respectively.

In CCS projects, the transportation of CO₂ by ship can be an attractive alternative to transportation using a pipeline, particularly when the distance between source and disposal location is large. However, the energy consumption of the liquefaction process can be significant, making the selection of an energy-efficient design an important factor in the minimization of operating costs. Since the liquefaction process operates at low temperature, its energy consumption will vary with ambient temperature, which could be a factor that influences the trade-off point between pipelines and shipping in different geographic locations. A consistent set of data showing the relationship between energy consumption and cooling temperature is therefore potentially useful to CCS system modelling. This study compares the performance of a wide range of CO₂ liquefaction schemes. It applies a methodical approach to the optimization of process operating parameters and studies performance across a range of operating temperatures. A set of data for the minimum energy consumption cases is presented. The main findings are that open-cycle CO₂ processes often offer minimum energy consumption; NH₃ based schemes often offer better performance at higher ambient temperatures; and that for the cooling temperature range 15 to 50 °C, the energy consumption for the best performing liquefaction process rises by around 40%.

Cardamom is plant of the Zingiberaceae family. It has been used for the treatment of many diseases such as migraine, bronchitis, stomach and intestinal disorders. Cardamom contains triterpenes, resins, starch and fatty compounds. Phytosterols (stigmasterol, campesterol and β-sitosterol) are a group steroid alcohol in plants. They are used food, medicine and cosmetic industry. They are protective effects against some types of cancer too. Phytosterols are found in the vegetable oil such as the spindle, corn and soybean oil. This paper deals with the maximum oil and β-sitosterol yield were investigated by means of the supercritical CO₂ extraction of cardamom. The effect of operating parameters as temperature, pressure and CO₂ flow rate were investigated on oil yield. The amount of β-sitosterol was analyzed by Gas Chromatography-Mass Spectrometry (GC-MS) at optimized conditions. The optimized conditions were recorded as temperature of 40^oC, pressure of 200 bar and CO₂ flow rate of 4 L/min. The maximum oil yield and amount of β-sitosterol were found as 74.83 mg oil/g seed and 4.73 mg β-sitosterol/g seed cardamom under these conditions.

CO2 emission activity of xylotrophic fungi response to an increase in temperature in the range of 10-30 °C on the example of pure dikaryotic cultures of Fomes fomentarius s. str., F. inzengae, Fomitopsis betulina, F. pinicola, Phellinus igniarius was analyzed. Emission activity was assessed by the difference in CO2 concentration in 0.5-liter exposure chambers with Petri dishes with mycelium growing on agar at the beginning of exposure and an hour later using a Gasmet DX-4030 FTIR spectrometer (Gasmet Technologies Oy, Finland), error measurements ±50 ppm. Specific (μg CO2/cm2/h) and total (μg CO2/h) emission activity and its relationship with temperature and size (area) of the mycelium were assessed. It has been shown that in the range of 10-30 °C, the specific and total CO2 emission activity of the mycelium is closely and positively related to temperature. Specific emission, which is an indicator of the respiratory activity of the mycelium, does not depend on its size; its only driver is temperature, the relationship with which is linear: an increase in temperature by 10 °C causes an increase in the specific emission activity of the mycelium by 1.7 times. The total CO2 emission activity, which is an indicator of the total amount of CO2 emitted, is directly proportional to the specific emission activity and the size of the mycelium. In the range of 10-30 °C, an increase in temperature causes an almost equal increase in both the specific emission activity of the mycelium (Q10 1.7) and its growth (Q10 1.5) and causes an exponential increase in the total emission of CO2. This must be taken into account when predicting CO2 emissions from woody debris under climate change, as it could potentially contribute to accelerating climate change.

Hydrogen from natural gas reforming can be produced efficiently with a high CO2 capture rate. This can be achieved with oxygen-blown autothermal reforming as core technology combined with pressure-swing adsorption for hydrogen purification and refrigeration-based tail gas separation for CO2 capture and recirculation of residual hydrogen, carbon monoxide and methane. The low-temperature tail gas separation section is presented in detail, and to quantify the exergy efficiency of this section, a detailed exergy analysis is conducted. The irreversibilities in 42 different process components are quantified. In order to provide a transparent verification of the consistency of exergy calculations, the total irreversibility rate is calculated by two independent approaches: Through the bottom-up approach, all individual irreversibilities are added to obtain the total irreversibility rate. Through the top-down approach, the total irreversibility rate is calculated solely by the exergy flows crossing the control volume boundaries. The consistency is verified as the comparison of results obtained by the two methods shows a relative deviation of 4·10-7. The exergy efficiency of the CO2 capture process is calculated based on two different definitions. Both methods give a baseline exergy efficiency of 58.38%, which indicates a high degree of exergy utilisation in the process.

Voluntary carbon markets open horizons for private companies, public institutions, and individuals developing CO2 removal projects in peatlands to reduce overall carbon footprint. These steps, however, should be in line with appropriate rewetting targets. To do so, the base line information about the status of area must be assessed. Here we follow the methodology set by the carbon certification program standards which define the necessary steps for reference conditions assessment. In this study we practically test the fulfilment of necessary drained peatland baseline evaluation for paludiculture and carbon certification activities. Estimates on the greenhouse gas emission mitigation potential were summarized to define priorities and propose quantifiable measures with suggested paludiculture implementation. Our hands-on approach shows that it is possible for companies to implement rewetting strategies without large EU level project fundings when the conservation and economic aspects are met, thus boosting climate mitigation actions.

Four different Mn and Re catalysts for electrochemical CO2 reduction have been studied by IR spectroelectrochemistry (SEC) in dry acetonitrile. In the case of Mn(apbpy)(CO)3Br (apbpy= 4(4-aminophenyl)-2,2’-bipyridine) SEC suggests that a very slow catalytic reduction of CO2 occurs in acetonitrile also in the absence of proton donors, but at rather negative potentials. On the contrary, the corresponding Re(apbpy)(CO)3Br clearly displays a slow catalytic conversion already at the first reduction potential. Switching to saturated CO2 solutions in a mixture of acetonitrile and 5% of water as proton donor, the SEC of Mn(apbpy)(CO)3Br displays faster catalytic behavior.

Biochar soil amendment along with non-tillage agriculture, are often proposed as a strategy for organic carbon sequestration in soil. How the quality of biochar might influence the priming effect on soil organic matter mineralization and whether the addition of fresh organic matter will affect its stability in soil is still questionable. In the study, six biochars of different biomass origin and three exogenous organic matter sources were added to two distinct arable soils. CO2 emission was monitored for 100 days of incubation and CO2 flux was estimated. Results showed that biochar application increased soil CO2 fluxes. The highest peaks were recorded in treatments with food waste biochars, suggesting that this feedstock serves as sources of labile C fractions to soil microbes. Co-application of raw organic materials (manure and fresh clover biomass) enhanced CO2 emission and estimated carbon losses, especially in sandy soil with low organic carbon content. Biochar properties and content of labile C fractions can stimulate CO2 emission, however in a long-term period this contribution is negligible. Findings of our study showed that more attention should be paid to priming effects caused by addition of exogenous organic matter e.g. fertilizers or cover crops when applied to biochar amended soils.

The scope of this paper is to use plastic waste through the gasification process for producing electricity with low carbon dioxide emissions. Worldwide, plastic production increased, reaching 367 million tons in 2020, compared with 1.5 million tons in 1950. It is known that plastic incineration generates approximately 400 million tons of CO2 annually, and consequently, new solutions for a more efficient plastics reuse in terms of emissions generated are still expected. One method is to use plastic waste in a gasifier unit and the syngas generated in a gas turbine for electricity production. The co-gasification process (plastic waste with biomass) was analysed in different ratios. Gasification was carried out with air for an equivalent ratio (ER) between 0.10-0.45. The volume concentration of CO2 in syngas ranged from 2-12%, with the highest value obtained when poplar content in the mix was 95%. In this study, the option of pre- and post-combustion integration of the chemical absorption process (CAP) was investigated. Thus, CO2 emissions have decreased by 90% compared with the case without CO2 capture. By integrating the capture process, the global efficiency has reduced with 5.5 – 6.1 percentage points in a post-combustion case, according to the plastic content in the mix.

The rapid development of electrochemical CO2 reduction offers a promising route to convert in-termittent renewable energy into products of high value-added fuels or chemical feedstocks. However, low faradaic efficiency, low current density, and a narrow potential range still limited the large-scale application of CO2RR electrocatalyst. Herein, monolith 3D bi-continuous nano-porous Bismuth (np-Bi) electrodes are fabricated via a simple one-step electrochemical dealloying strategy from Pb-Bi binary alloy. The unique bi-continuous porous structure ensures highly effective charge transfer, meanwhile the controllable millimeter-size geometric porous structure enables easy catalyst adjustment to expose highly suitable surface curvatures with abundant reactive sites. This results in a high selectivity of 92.6% and superior potential window (400 mV, selectivity >88%) for electrochemical reduction of carbon dioxide to formate. Our scalable strategy provides a feasible pathway for mass-producing high-performance and versatile CO2 electrocatalysts.

Excessive CO₂ emissions and alternative energy fuels are two major difficult issues. The utilization of CO₂ into fine chemicals is an optimal route. Diethyl carbonate (DEC) is an extremely versatile chemical intermediate. DEC is used in gasoline, pharmaceutical, chemical and other fields. DEC synthesis from CO₂ and ethanol is a typical green synthetic route. Ni-Cu@Na₃PW₁₂O₄₀ catalysts were synthesized by two novel methods of supported and mixed. The catalyst prepared by mixed method showed nice catalytic performance. It was confirmed that water removal was the key to improving conversion efficiency. In the presence of dehydrating agent of ethylene, ethanol conversion increased from ca. 3% to ca. 40%. Propylene oxide (PO) was participated in the reaction and ethanol conversion continued to reach to ca.90% while DEC selectivity dropped by half. Under optimal conditions, our Ni-Cu@Na₃PW₁₂O₄₀ catalyst effectively solved the two major issues above.

Nowadays, one of the biggest concern of human being is greenhouse gas emission, especially carbon dioxide emission in developed and under-developing countries. In this study, connectionist models including LSSVM (Least Square Support Vector Machine) and evolutionary methods are employed for predicting the amount of CO₂ emission in six Latin American countries, i.e., Brazil, Mexico, Argentina, Peru, Chile, Venezuela, and Uruguay. The studied region is modelled based on the available input data in terms of Million tons including oil (Million tons), gas (Million tons oil equivalent), coal (Million tons oil equivalent), $R_{ew}$ (Million tons oil equivalent), and Gross Domestic Product (GDP) in terms of billion US dollars.} Moreover, the available patents in the fields of climate change mitigation in six Latin American countries namely Brazil, Mexico, Argentina, Peru, Chile, Venezuela, and Uruguay has been reviewed and analyzed. The results show that except Venezuela, all other mentioned countries have invested in renewable energy R&D activities. Brazil and Argentina have the highest share of renewable energies which account for 60% and 72% respectively.

Soybean yields are often indicated as an interesting case of climate change mitigation due to the beneficial effects of CO₂ fertilization. In this paper we econometrically study this effect using a time series model of yields in a multivariate framework for a main producer and exporter of this commodity, Argentina. We have to deal with the upward behavior of soybean yields trying to identify which variables are the long-run determinants responsible of its observed trend. With this aim we adopt a partial system approach to estimate subsets of long-run relationships due to climate, technological and economic factors. Using an automatic selection algorithm we evaluate encompassing of the different obtained equilibrium correction models. We found that only technological innovations due to new crop practices and the use of modified seeds explain soybean yield in the long run. Regarding short run determinants we found positive effects associated with the use of standard fertilizers and also from changes in atmospheric CO₂ concentration which would suggest a mitigation effect from global warming. However, we also found negative climate effects from periods of droughts associated with La Niña episodes, high temperatures and extreme rainfall events during the growing season of the plant.

The aim of the present study is to provide new insights into the CO2 and CH4 adsorption using a set of biomass-based activated carbons obtained by physical and chemical activation of olive-stones. The adsorption behavior is analyzed by means of pure gas adsorption isotherms up to 3.2 MPa at two temperatures (303.15 and 323.15 K).The influence of the activation method on the adsorption uptake is studied in terms of both textural properties and surface chemistry. For three activated carbons the CO2 adsorption was more important than that of CH4. The chemically activation resulted in higher BET surface area and micropore volume that lead to higher adsorption for both CO2 and CH4. For methane the presence of mesopores seems to facilitate the access of the gas molecules into the micropores while for carbon dioxide, the presence of oxygen groups enhanced the adsorption capacity.

Seeds of three C₃ and one C₄ annual weedy species were collected from agricultural fields in Beltsville, Maryland in 1966 and 2006, when atmospheric CO₂ concentrations averaged about 320 and 380 mmol mol^-1, respectively. Plants from each collection year were grown over a range of CO₂ concentrations to test for adaptation of these weedy species to recent changes in atmospheric CO₂. In all three of the C₃ species, the increase in CO₂ concentration from 320 to 380 mmol mol^-1 increased total dry mass at 24 days in plants from seeds collected in 2006, but not in plants from seeds collected in 1966. Shoot and seed dry mass at maturity was greater at the higher growth CO₂ in plants collected in 2006 than in 1966 in two of the species. Down regulation of photosynthetic carboxylation capacity during growth at high CO₂ was less in the newer seed lots than in the older in two of the species. Overall, the results indicate that adaptation to recent changes in atmospheric CO₂ has occurred in some of these weedy species.

In this work, Density Functional Theory (DFT) calculations were employed to study the photocatalytic CO2 to CO reduction by a series of Pt(II) square planar complexes with general formula [Pt(5-R-dpb)Cl] (dpb = 1,3-di(2-pyridyl)benzene anion, R = H, N,N-dimethylaniline,T thiophene, diazaborinine). The CO2 to CO conversion process is thought to proceed via two main steps, namely the photocatalytic/reduction step and the main catalytic step. The simulated absorption spectra exhibit strong bands in the 200 – 400 nm UV-Vis region. The calculated excited state reduction potentials are in the range 0.32 — -0.36 V revealing that the reductive quenching of the T1 state of the complexes could be modulated with suitable changes of the N^C^N pincer ligands. The CO2 fixation and activation by the ‘real’ three coordinated Pt(II) catalyst/intermediate is predicted to be favorable with Pt-CO2 bond dissociation energies, D0 in the range -36.9—-10.3 kcal/mol. The nature of the Pt-CO2 bond is complex with covalent, hyperconjugative and H-bonding interactions prevailing the repulsive electrostatic interactions. The main catalytic cycle is estimated to be a favorable exergonic process.

Important first phases in the process of implementing CO2 subsurface and ocean storage projects include selecting of best possible location(s) for CO2 storage, site selection evaluation. Sites must fulfil a number of criteria that boil down to the following basics: they must be able to accept the desired volume of CO2 at the rate at which it is supplied from the CO2 source(s); they must as well be safe and reliable; and must comply with regulatory and other societal requirements. They also must have at least public acceptance and be based on sound financial analysis. Site geology; hydrogeological, pressure, and geothermal regimes; land features; location, climate, and access, etc. can all be refined from these basic criteria. In addition to aiding in site selection, site characterization is essential for other purposes, such as foreseeing the fate and impacts of the injected CO2, and informing subsequent phases of site development, including design, permitting, operation, monitoring, and eventual abandonment. According to data from the IEA, in 2022, emissions from Africa and Asia's emerging markets and developing economies, excluding China's, increased by 4.2%, which is equivalent to 206 million tonnes of CO2 and were higher than those from developed economies. Coal-fired power generation was responsible for more than half of the rise in emissions that were recorded in the region. The difficulty of achieving sustainable socio-economic progress in the developing countries is entwined with the work of reducing CO2 emissions, which is a demanding project for the economy. Organisations from developing countries, such as Bangladesh, Cameroon, India, and Nigeria, have formed partnerships with organisations in other countries for lessons learn and investment within the climate change arena. The basaltic rocks, coal seams, depleted oil and gas reservoirs, soils, deep saline aquifers, and sedimentary basins that developing countries (Bangladesh, Cameroon, India, and Nigeria etc) possesses all contribute to the individual country's significant geological sequestration potential. There are limited or no carbon capture and storage or clean development mechanism projects running in these countries at this time. The site selection and characterization procedure are not complete without an estimate of the storage capacity of a storage location. Estimating storage capacity relies on volumetric estimates because a site must accept the planned volume of CO2 during the active injection period. As more and more applications make use of site characterization, so too does the body of written material on the topic. As the science of CO2 storage develops, regulatory requirements are implemented, field experience grows, and the economics of CO2 capture and storage improve, so too will site selection and characterisation change.

This study aimed to solve the problems of sealing and tearing failure of packer’s rubber cylinders during CO2 downhole injection. Using the simulation software, Comsol, a rubber cylinder model in a supercritical CO2 (SC-CO2) environment was established. The thermal analogy method was used to simulate the CO2 diffusion and rubber cylinder swelling process, thus we analyzed the deformation and stress of the rubber cylinder caused by temperature, pressure and CO2 as swelling agent. Results showed that, in the SC-CO2 environment, under the influence of CO2 diffusion and the consequent swelling, the rubber cylinder body is prone to large deformation, and the maximum shear stress is significantly increased, leading to shear failure of the rubber cylinder. The reduction of the initial seating pressure can alleviate the impact of deformation, whereas the reduction of the maximum contact pressure could cause the rubber cylinder to lose its seal. We also analyzed the change rules between various factors and the maximum contact pressure of the rubber cylinder, which provides a theoretical basis and technical support for improving the sealing performance of the packer’s rubber cylinder in the SC-CO2 environment.

In recent years, technical processes for the sequestration of CO2 through industrial waste mineral carbonation have been explored and developed. There is a large portfolio of Carbon Capture, Uti-lisation and Storage (CCUS) techniques that have been employed on a laboratory and at pilot scale. These include geological storage, ocean storage and mineralisation by carbonate ores. In view of this, the main purpose of this research was to investigate and explore chemical variables, particularly ammonium salts as lixiviants for calcium mineral extraction from iron making slag. The slag in use was acquired from a Steel Mill in the Vaal Triangle Region in Gauteng, South Af-rica. The experimental test work was conducted using different ammonium lixiviants, namely, NH4NO3, NH4Cl and CH3COONH4 to understand the influence of anion type as well as possible differences in mechanisms of interactions. Lixiviant concentration as well as the reaction time were varied in this research study. The three selected ammonium based lixiviants showed different extents of calcium extraction owing to differences in the anion groups. NH4NO3, NH4Cl and CH3COONH4 were found capable of dissolving 50% to 80% of calcium from the selected slag for different molar concentrations. Anion type and leaching time also had significant influences on the leaching of calcium from the slag. Rapid pH degradation resulted in better calcium extraction ca-pabilities. This work has shown that the selected ammonium salts have a potential as lixiviants for calcium dissolution from iron making blast furnace slags. These lixiviants would therefore be important to consider during calcium mineral carbonation for CO2 sequestration.

Ammonia can be considered a relevant compound in the future energy sector, playing a significant role as an energy carrier, storage, or carbon-free fuel. However, the production of this molecule has a high energy demand, and the use of natural gas, which is not free of controversy due to the accidental leakage into the atmosphere produced during extraction and the fact that it is a non-renewable source, contributes to increasing greenhouse gas emissions. Reducing the process’s energy demand and carbon footprint will be essential to making ammonia a clear alternative for a carbon-free economy. Given the vast experience in ammonia production and handling, this gas seems to be the logical step forward in the evolution of the energy sector. However, the current uncertainty in the global market requires cautiousness in decision-making. Several factors may impact economic growth and human welfare, thus needing a careful assessment before taking any transcendental decisions that could affect worldwide energy prices and raw material availability.

Background: The validation of laser usage during laparoscopic procedures, notably by Camran Nezhat in the late 1980s, has been significant. Lasers offer precision and depth control in tissue vaporization without bleeding. Surgical intervention remains central in managing endometrio-sis-associated pain and infertility, especially for patients unresponsive to hormonal therapy. Methods: This retrospective cohort study included 200 patients with SPE who underwent laparo-scopic laser vaporization. Surgery was performed using a CO2 laser, and histological confirma-tion of endometriosis was obtained for all cases. Pain scores and SF-36 questionnaire domains were assessed preoperatively and postoperatively. Fertility outcomes were evaluated among pa-tients desiring pregnancy. Results: Significant improvements in pain score and SF-36 questionnaire domains were ob-served postoperatively (p-value

Climate change is rapidly exacerbating and adding to major-to-existential issues associated with fresh water availability and utilization. The massive thus far untapped saline/salt water - oceans/wastelands/deserts – Halophytes resources nexus can, at scale and profitably provide major climate change mitigation and greatly alleviate most extant fresh water issues. Approaches include ocean fertilization and saline/seawater agriculture on deserts and wastelands to sequester massive amounts of CO2 and methane and for food, freeing up the some 70% of the fresh water now utilized by current agriculture for direct human use. Also enables production of huge amounts of Bio/SAF fuels and bio mass based chemical feed stock employing the massive capacity of cheap saline/ seawater and cheap deserts, wastelands. Overall saline/ seawater can, uniquely, at the scale of the climate and fresh water issues, without desalinization, profitably, utilizing extant technologies and the some 44% of the land that is deserts/ wastelands, and the 97% of the water that is saline/ seawater rapidly, seriously, address land, fresh water, food, energy and climate.

The increase in carbon dioxide emissions has a significant impact on human society and the global environment. As the most abundant and cheap C1 resource, the conversion and utilization of carbon dioxide has received extensive attention from researchers. In many methods of carbon dioxide conversion and utilization, the reverse water gas conversion reaction is considered to be one of the most effective ways. In this paper, the research progress of reverse water gas conversion reaction in recent years is introduced.

A large amount of steel slag (SS) and CO2 are generated in the steelmaking process. The indirect CO2 capture using SS is a promising way for co-treatment of the wastes. Ammonium salt solution is widely used to extract Ca2+ from the SS since it is recyclable. Several works have focus on improving the carbonation rate by adjusting various parameters (e.g., temperature and pH). However, there is little detail information about the associating behaviors and interaction strength between the various ions in the ammonia solution during the carbonation process. In this work, the Ca2+–CO32-–NH4+–Cl-–H2O system was established by using Material studio software. The effects of temperature and concentration of CO32- on CaCO3 growth were explored at the atomic scale by calculating the binding energy, mean square displacement, and diffusion coefficient between particles. Furthermore, the microstructure, bonding characteristics, and occurrence behavior of each particle were studied though molecular dynamics simulation methods. The results showed that with the increase of temperature (20–80 ℃), the binding ability and diffusion coefficients of Ca2+ and CO32- increase in the system, which is beneficial to the formation of CaCO3 clusters. With the increase of the concentration of CO32- (15–25 vol.%), the binding ability and diffusion coefficient of Ca2+ and CO32- in the system are enhanced, which is beneficial to the formation of CaCO3 clusters.

Following the international trend of using hydrogen as combustible in many industry branches, this paper investigates the impact of mixing methane gas with 23% hydrogen (G222) on condensing boilers’ operation. After modeling and testing several boilers with heat exchange surface different designs, the authors gathered enough information to introduce a new concept, namely High-Performance Condensing Boiler (HPCB). All the boilers that fit into this approach have the same operational parameters at nominal heat load, including the CO2 concentrations in flue gases. After testing a flattened pipes condensing boiler, a CO2 emission reduction coefficient of 1.1 was determined, when converting from methane gas to G222 as combustible. Thus, by inserting into the national grid a G222 mixture, an important reduction in greenhouse gases can be achieved. For a 28 kW condensing boiler the annual reduction in CO2 emissions averages 1.26 tons, value which was experimentally obtained and is consistent with the theoretical evaluation.

The conversion of CO2 into more synthetically flexible CO is an effective and potential method for CO2 remediation, utilization and carbon emission reduction. In this paper, the reaction of carbon-carbon dioxide (Boudouard reaction) was performed in a microwave fixed bed reactor using semi-coke (SC) as both the microwave absorber and reactant and was systematically compared with that heated in a conventional thermal field. The effects of the heating source, SC particle size, CO2 flow rate and additives on CO2 conversion and CO output were investigated. By microwave heating (MWH), CO2 conversion reached more than 99 %, while by conventional heating (CH), the maximum conversion of CO2 was approximately 29% at 900 °C. Meanwhile, for the reaction with 5 wt% Barium Carbonate added as a promoter, the reaction temperature was significantly reduced to 750 °C with almost quantitative conversion of CO2. Further kinetic calculations showed that the apparent activation energy of the reaction under microwave heating was 46.3 kJ/mol, which was only one-third of that observed under conventional heating. The microwave-assisted Boudouard reaction with catalytic barium carbonate is a promising method for carbon dioxide utilization.

The changing dynamics in climate is the primary and important determinant of agriculture productivity. The effects of this changing climate on overall productivity in agriculture can be understood when we study the effects of individual components contributing to the changing climate on plants and crops. Elevated CO₂ (eCO₂) and drought due to high variability in rainfall is one of the important manifestations of the changing climate. There is a considerable amount of literature that addresses climate effects on plant systems from molecules to ecosystems. Of particular interest is the effect of increased CO₂ on plants in relation to drought and water stress. As it is known that one of the consistent effects of increased CO₂ in the atmosphere is increased photosynthesis, especially in C₃ plants, it will be interesting to know the effect of drought in relation to elevated CO₂. The potential of elevated CO₂ ameliorating the effects of water deficit stress is evident from literature suggesting that these two are agents are brothers in arms protecting the plant from stress rather than partnering in crime, specifically water deficit when in isolation. The possible mechanisms by which this occurs will be discussed in this minireview. Interpreting the effects of short-term and long-term exposure of plants to elevated CO₂ in the context of ameliorating the negative impacts of drought will show us the possible ways by which there can be effective adaption to crops in the changing climate scenario.

This study investigated the physical properties of section-restoration mortar with calcium nitrite and carbon dioxide (CO2) nanobubble mixing water to develop materials and methods for the repair and reinforcement of cracks in reinforced concrete (RC) structures. As the calcium nitrite content increased, the generation rate and generated amount of nitrite-based hydration products increased, owing to the rapid reaction between NO2- ions in calcium nitrite and C3A(Al2O3). Further, the reaction with C3S and C2S was accelerated, thereby increasing the generation rates of Ca(OH)2 and C-S-H. Further, the large amount of Ca2+ ions in these hydration products reacted with CO32- ions in CO2 nanobubble water, thereby increasing the generation of calcite-based CaCO3 in the cement matrix. This appears to have affected the strength development and durability improvement via the densification of the structure. These results suggest that the performance of polymer cement mortar for repairing concrete structures can be improved if calcium nitrite and CO2 nanobubble water are properly combined and applied.

Results of rapid economic growth, China, USA, and India have become the largest energy stealer and the greatest emitter of CO₂ in the world and burn over 45% of global fuels in 2016. Meanwhile, the developing strategies of 24 polluted countries to decrease the energy consumption without additional economic output. This paper is exploring the effect of world top polluted countries C0₂ emission and their GDP and the production of electricity by energy indicators. The GLM model is not predict logistic and probit analysis directly; instead, it is mainly used for instinct to response of CO₂ emission, using data for the period 1968-2017. The huge production of electricity will cause of abnormal CO₂; this study offers true indication of exploring consumption of energy issues from the perspective of Granger casual and a positive unidirectional causality is detected between energy consumption to economic growth, while short-run bidirectional casualty exists among energy indicators.

Solid porous materials, like zeolites, have been widely used in a variety of fields such as size and shape-selective absorption/separation and catalysis because of their porosity. But there are few liquid materials exhibit permanent porosity. Porous liquids are a novel material that combine the properties of fluidity and permanent porosity. It has potential applications in many fields such as gas separation, storage and transport. Herein, we report a novel Type 1 porous liquid prepared based on Silicalite-1. The pore size of this porous liquid was determined by positron annihilation lifetime spectroscopy (PALS), and the CO2 capacities was determined by the intelligent gravimetric analyser (IGA). The unique properties of this porous liquid can promote its application in many fields such as gas storage and transport.

The photoreduction of CO2 is an intriguing process, which allows the synthesis of fuels and chemicals. One of the limitations for CO2 photoreduction in the liquid phase is its low solubility in water. This point has been here addressed by designing a fully innovative concept of pressurized photoreactor, allowing operation up to 20 bar and applied to improve the productivity of this very challenging process. The photoreduction of CO2 in the liquid phase was performed using commercial TiO2 (Evonink P25), TiO2 obtained by flame spray pyrolysis (FSP) and gold doped P25 (0.2 wt% Au-P25) in the presence of Na2SO3 as hole scavenger (HS). The different reaction parameters (catalyst concentration, pH and amount of HS) have been addressed. The products in liquid phase were formic acid and formaldehyde. Moreover, for longer reaction time and with total consumption of HS, gas phase products formed (H2 and CO) after accumulation of significant amount of organic compounds in the liquid phase, due to their consecutive photoreforming. Enhanced CO2 solubility in water was achieved by adding a base (pH= 12-14). In basic environment, CO2 formed carbonates which further reduced to formaldehyde and formic acid and consequently formed CO/CO2+H2 in the gas phase through photoreforming. The deposition of small Au nanoparticles (3-5 nm) (NPs) onto TiO2 was found to quantitatively influence the products distribution and increase the selectivity towards gas phase products.

There is a potential for synergy effects in utilizing CO2 for both enhanced gas recovery (EGR) and geothermal energy extraction (CO2-plume geothermal, CPG) from natural gas reservoirs. This “combined CO2-EGR–CPG system” has been introduced as a feasible approach that constitutes a CO2 Capture double-Utilization and Storage (CCUUS) system. In this study, we carry out reservoir simulations, using TOUGH2, to evaluate the sensitivity of the natural gas recovery, pressure buildup, and geothermal power generation performance of the combined system to various key reservoir and operational parameters. The reservoir parameters include horizontal permeability, permeability anisotropy, reservoir temperature, and pore-size-distribution index; while the operational parameters include wellbore diameter and ambient surface temperature. Using an example of a natural gas reservoir model, we also investigate the effects of different strategies of transitioning from the CO2-EGR stage to the CPG stage on the energy-recovery performance metrics and on the two-phase fluid-flow regime in the production well. The simulation results show that overlapping the CO2-EGR and CPG stages and having a relatively brief period of CO2 injection but no production (which we call the CO2-plume establishment stage) achieves the best overall energy (natural gas and geothermal) recovery performance. Permeability anisotropy and reservoir temperature are the parameters the natural gas recovery performance of the combined system is most sensitive to. The geothermal power generation performance is most sensitive to the reservoir temperature and the production wellbore diameter. The results of this study pave the way for future CPG-based geothermal power-generation optimization studies. For a CO2-EGR–CPG project, the results can be a guide regarding the required accuracy of the reservoir parameters during exploration and data acquisition.

This study explores the innovative use of CO2 laser technology in frenuloplasty, a significant shift from traditional methods like scalpel surgery or electrocautery, towards a minimally invasive approach. The research involved 15 patients aged 25 to 50, undergoing frenuloplasty with a CO2 laser system equipped with a 7-inch defocused handpiece, set at 20Hz and 0.3W. This method diverges from conventional laser techniques, focusing on controlled laser passes combined with manual traction to elongate the fibrous tissue of the frenulum. The results demonstrated that the CO2 laser technique allowed for a precise and progressive modification of the frenulum, significantly reducing the risks of hemorrhage and secondary in-tention fibrosis. The healing process was notably expedited, with patients reporting satisfactory outcomes within a two-week period. Statistically significant improvements were observed in pa-tient-reported outcomes, as evidenced by the increases in the Short Form Health Survey (SF-12) scores, with the mean Physical Component Summary (PCS) score rising from 32.5 to 47.5 and the mean Mental Component Summary (MCS) score from 39.3 to 52.3 (p < 0.001 for both). The study concludes that CO2 laser frenuloplasty is an effective and safe technique, offering sub-stantial benefits in terms of reduced healing time and enhanced patient satisfaction. The signifi-cant improvements in SF-12 scores underscore the positive impact on patient quality of life, ad-vocating for the broader application of this technique in clinical practice. Further research is warranted to explore its potential in a wider clinical context.

The present review revisits representative studies addressed to develop efficient carbon-based heterogeneous catalysts for two important reactions, namely, the production of hydrogen from formic acid and the hydrogenation of carbon dioxide to formic acid. The HCOOH-CO2 system is considered a promising couple for a hydrogen storage system that would be involved in an ideal carbon-neutral cycle. Significant advancements have been achieved in those catalysts designed to catalyze the dehydrogenation of formic acid under mild reaction conditions, while much effort is still needed to catalyze the challenging CO2 hydrogenation reaction. The design of carbon-based heterogeneous catalysts for these reactions encompasses both the modulation of the properties of the active phase (particle size, composition, and electronic properties), as well as the modification of the supports by means of incorporation of nitrogen functional groups. These approaches are herein summarized to provide a compilation of the strategies followed in recent studies to set the basis for a hydrogen storage system attained by the HCOOH-CO2 couple.

We explore the use of industrial sources of silicon and surfactant for obtaining low-cost MCM-41 materials and evaluate their performance as CO₂ adsorbents. All of them presented a high specific surface area with different structural characteristics and textural properties. The template was removed by using thermal treatments in an air atmosphere or a washing process. Preservation of silanol groups proved to be more effective under washing or mild thermal treatment conditions with the advantage of their lower cost and environmental benefit. Surface reactivity against CO₂ was enhanced by anchoring APTS to silanol groups through wet grafting. All amino-functionalized materials showed a performance as CO₂ adsorbents comparable to those reported in the literature. Samples with a higher concentration of silanol groups showed better performance. Our studies indicate that adsorbed CO₂ is retained at least up to 50°C, and the presence of aminopropyl groups is a key issue in CO₂ chemisorption on the MCM-41 surface. The chemisorbed gas at very low pressures points to the potential use of these materials for CO₂ storage.

CO2 flooding stands as a pivotal technique for significantly enhancing oil recovery in low-permeability reservoirs. The movement and sweeping rules at the front of CO2 flooding play a critical role in its oil recovery, yet a comprehensive quantitative analysis remains an area in need of refinement. In this study, we have developed 1D and 2D numerical simulation models to explore the sweeping behavior of miscible, immiscible, and partly-miscible CO2 flooding patterns. The front position and movement rules of the three CO2 flooding patterns are determined. A novel approach of the contour area calculation method is introduced to quantitatively characterize the sweep coefficients, and the sweeping rules are discussed regarding geological parameters, oil viscosity, and injection-production parameters. Furthermore, the Random Forest (RF) algorithm is employed to identify the controlling factor of the sweep coefficient, as determined by out-of-bag (OOB) data displacement analysis. The results show that the miscible front is located at the point of maximum CO2 content in the oil phase. The immiscible front occurs at the point of maximum interfacial tension near the production well. Remarkably, the immiscible front moves at a faster rate compared to the miscible front. Geological parameters, including porosity, permeability, and reservoir thickness, significantly impact the gravity segregation effect, thereby influencing the CO2 sweep coefficient. Immiscible flooding exhibits the highest degree of gravity segregation, with a maximum gravity segregation degree (GSD) reaching 78.1. The permeability ratio is a crucial factor, with a lower limit of approximately 5.0 for reservoirs suitable for CO2 flooding. Injection-production parameters also play a pivotal role in sweep coefficient. Decreased well spacing and increased gas injection rates are found to enhance sweep coefficients by suppressing gravity segregation. Additionally, higher gas injection rates can improve the miscibility degree of partly-miscible flooding from 0.69 to 1.0. Oil viscosity proves to be a significant factor influencing the sweep coefficients, with high seepage resistance due to increasing oil viscosity dominating the miscible and partly-miscible flooding patterns. Conversely, gravity segregation primarily governs the sweep coefficient in immiscible flooding. In terms of controlling factors, the permeability ratio emerges as a paramount influence, with a factor importance value (FI) reaching 1.04. these results provide a theoretical foundation for the application of CO2 flooding, enhancing the understanding of the critical factors governing its success.

FeZnNa@SiO2-C catalyst with graphitized carbon (GC) modified mesoporous SiO2 support metal nanoparticles was prepared by sol-gel method. The effect of adding metal Na and Zn promoters as a dispersion on the CO2 hydrogenation to low olefins was systematically studied. The results showed that Zn-Na, as a combination, promoted the absorption of CO2 and improved the conversion rate of CO2. Na as an alkaline substance can improve the absorption of more acidic CO2, improving the conversion rate of CO2 to 59.03%. Meanwhiles, addition of secondary metal Zn into Fe-based catalysts to form a surface alloy could alter the adsorption of CO2 and the activation of C-O bonds, inhibit the subsequent hydrogenation of olefins to paraffins, facilitate the reduction of Fe2O3 and the formation of active Fe5C2 species. From TEM and XRD, the formation of active Fe5C2 species was found, the selectivity of the target product was 41.07%. The deep hydrogenation of olefins is inhibited, by inhibiting their deep hydrogenations, the STY of C2=-C4= was raised again, up to 0.0436. However, the corresponding STY does not increase infinitely with the increase of Na content, and when the Na content to 6.4%, which can be shown higher CO2 hydrogenation catalytic performance. Compared with Fe@SiO2-C catalyst, Na and Zn promoted Fe-based catalysts prepared by modified sol-gel method, can be used directly for highly efficient CO2 hydrogenation to low olefins and thus will be more promising in the future.

Current environmental conditions have prompted agri-food systems to explore new strategies for improving the production of crops in a sustainable manner. The use of omeprazole (OMP) and melatonin (MEL) have been proposed as innovative strategy for crop improvement when applied as biostimulants. However, although their role in the growth of several species has been studied, the results in photosynthetic efficiency parameters are still scarce. Therefore, the objec-tive of the present study was to evaluate the effect of foliar application of OMP and MEL on bi-omass, yield, SPAD values, leaf chlorophyll fluorescence (Fv/Fm), photochemical quenching (qP), Non-photochemical quenching (NPQ), quantum yield of photosystem II (PhiPSII) and elec-tron transport rate (ETR) in bean plants. Treatments were applied separately at doses of 1, 10, and 100 µM, plus a control without application. The results obtained indicate that OMP and MEL were able to increase biomass, yield, SPAD values, as well as photochemical quenching, fluores-cence, and PhiPSII coefficients. Finally, it is concluded that foliar application of OMP and MEL at a dose of 1 and 10 µM can increase photosynthetic efficiency and decrease photoinhibition, which is reflected in higher biomass accumulation and yield in green bean plants cv. Strike.

In response to the problem of increasing climate change and energy security, investment in renewable energy sources has increased significantly both in Europe and globally. Wind and solar power plants are expected to be the largest contributors to global decarbonization, ranking first and second in projected capacity by 2050. Since all power plants have some impact on the environment, this also applies to photovoltaic power plants. Because of the large capacities projected for PV installed capacity, their environmental impacts should be evaluated. The environmental impacts of PV power plants change over time. Improving the manufacturing technology of PV system components, increasing the efficiency of solar cells, and using materials that are less harmful to the environment will reduce these impacts. Manufacturing PV system components is a highly energy-intensive process that involves greenhouse gas emissions. As new renewable energy capacity is built, the amount of "green" electricity on the grid increases, reducing CO2 emissions per kWh consumed. The objective of this paper is to analyze the current status of the environmental impact of PV power plants under these changing conditions in terms of CO2 emissions, land use, pollutant and noise emissions, and water consumption. The capacity installed to date will reach the end of its lifetime by 2050, which means that the amount of waste associated with it will increase over time. This can have a significant impact on the environment, which is why part of the work is dedicated to this problem. In addition to the available information from the literature, in the part related to land use, the authors also made their own estimates based on data on newly installed PV power plants and PV modules available on the market. The results of the analysis show that there is enough land both in Europe and worldwide to install the planned capacities of rooftop and ground-mounted PV power plants. CO2 emissions are at the same level as for concentrated solar power, with a decreasing trend. Pollutant emissions, noise and water consumption are not a major problem compared to other types of power plants. Overall, it can be concluded that the expansion of PV capacity has a very positive impact on the environment.

With the popularization of natural gas and the requirements for environmental protection, the development and utilization of natural gas is particularly important. The status of natural gas in China's oil and gas exploration and development is constantly improving, and the country is paying more and more attention to the exploitation and utilization of natural gas. The Upper Paleozoic tight sandstone in the Ordos Basin is characterized by low porosity, low permeability and large area of concealed gas reservoirs. By injecting CO2 into the formation, the recovery of natural gas can be improved, and at the same time, the stable storage of CO2 can be achieved to achieve a win-win situation of CO2 emission reduction and utilization. Injecting greenhouse gas CO2 into gas reservoirs for storage and improving recovery has also become a hot research issue. In order to improve the recovery efficiency of tight sandstone gas reservoir, this paper takes the complex tight sandstone of Upper Paleozoic in Ordos Basin as the research object, through indoor physical simulation experiments, carried out the influence of displacement rate, fracture dip angle, core permeability, core dryness and wetness on CO2 gas displacement efficiency and storage efficiency, and analyzed the influence of different factors on CO2 gas displacement efficiency and storage efficiency to improve the recovery and storage efficiency. The research results show that under different conditions, when the CO2 injection pore volume is less than 1PV, the relationship between the CH4 recovery rate and the CO2 injection pore volume is linear, and the tilt angle is 45 °. When the CO2 injection pore volume exceeds 1PV, the CH4 recovery rate increases slightly with the increase of displacement speed, the recovery rate of CO2 displacement CH4 is between 87% - 97%, and the CO2 breakthrough time is 0.7PV-0.9PV. In low-permeability and low-speed displacement cores, the diffusion of CO2 molecules is more significant. The lower the displacement speed is, the earlier the breakthrough time of CO2 is, and the final recovery of CH4 slightly decreases. Gravity has a great impact on CO2 storage and enhanced recovery. The breakthrough of high injection and low recovery of CO2 is earlier, and the recovery of CH4 is about 3.3% lower than that of low injection and high recovery. The bound water makes the displacement phase CO2 partially dissolved in the formation water, and the CO2 breakthrough lags about 0.1PV. Ultimately, CH4 recovery factor and CO2 storage rate are higher than those of dry core displacement. The research results provide theoretical data support for CO2 injection to improve recovery and storage efficiency in complex tight sandstone gas reservoirs.

Minimum miscibility pressure (MMP) and oil swelling are two important factors of carbondioxide (CO₂) gas displacement mechanism occurred in the reservoir relate to application of CO₂ injection in the field to enhance oil recovery. In this paper determination of minimum miscibility pressure (MMP) between crude oil samples with carbondioxide gas conducted using two methods, i.e. correlation methods and laboratory experiment using slimtube. While, determination of swelling factor was conducted using PVT cell, where recombined fluid injected and conditionally at the reservoir temperature. The results of MMP using empirical equation (2807 Psig) and Holm & Josendal correlation (2750 Psig) is more approximate to the result of laboratory analysis (2805 Psig). The result of swelling test during injection CO₂ gas processes until 46.82% mole, shows that bubble point pressure is increasing gradually from 410 psig through 2200 psig, and swelling factor was also increase from 1.0 through 1.442. Based on the value of fracture pressure of Layer F in the KHL Field is 2200 Psig and MMP is 2805 Psig, hence the application of CO₂ gas injection in the field only could be conducted as immiscible flooding.

The electrochemical CO2 reduction reaction can lead to high value-added molecules production while helping decrease anthropogenic CO2 emissions. Copper can reduce CO2 to more than thirty different hydrocarbons and oxygenates, but it lacks the required selectivity. We present a computational investigation of the role of nano-structuring and alloying in Cu-based catalysts on the activity and selectivity of CO2 reduction to one-carbon products: carbon monoxide, formic acid, formaldehyde, methanol, and methane. The adsorption, activation, and conversion of CO2 were computed on monometallic and bimetallic (decorated and core-shell) 55-atom Cu-based clusters. The dopant metals considered were Ag, Cd, Pd, Pt, and Zn, located at different coordination sites. The relative binding strength of the intermediates at different applied potentials were used to identify the optimal catalyst for the selective CO2 conversion to one carbon products. It was discovered that single atom doping with Cd and Zn is optimal for the CO2 to carbon monoxide conversion. The core-shell models with Ag, Pd, and Pt provided higher selectivity for formic acid and formaldehyde. The Cu-Pt and Cu-Pd showed lowest overpotential for methane formation.

The response of carbon fixation in C3 plants to elevated CO2 is relatively larger when photosynthesis is limited by carboxylation capacity (VC) than when limited by electron transport (J). Recent experiments under controlled, steady-state conditions have shown that photosynthesis at elevated CO2 may be limited by VC even at limiting PPFD. These experiments were designed to test whether this also occurs in dynamic field environments. Leaf gas exchange was recorded every 5 minutes using two identical instruments both attached to the same leaf. The CO2 concentration in one instrument was controlled at 400 mol mol-1 and one at 600 mol mol-1. Leaves were exposed to ambient sunlight outdoors, and cuvette air temperatures tracked ambient outside air temperature. The water content of air in the leaf cuvettes was kept close to that of the ambient air. These measurements were conducted on multiple, mostly clear days for each of three species, Glycine max, Lablab purpureus, and Hemerocallis fulva. The results indicated that in all species, photosynthesis was limited by VC rather than J at both ambient and elevated CO2 both at high midday PPFDs and also at limiting PPFDs in the early morning and late afternoon. During brief reductions in PPFD due to midday clouds, photosynthesis became limited by J, The net result of the apparent deactivation of Rubisco at low PPFD was that the relative stimulation of diurnal carbon fixation at elevated CO2 was larger than would be predicted when assuming limitation of photosynthesis by J at low PPFD.

Shear deformation of a solid-fluid, two-phase material induces a fluid segregation process that produces fluid-enriched bands and fluid-depleted regions, and crystallographic preferred orientation (CPO) characterized by girdles of [100] and [001] axes sub-parallel to the shear plane and a cluster of [010] axes sub-normal to the shear plane, namely the AG-type fabric. Based on experiments of two-phase aggregates of olivine + basalt, a two-phase flow theory and a CPO-formation model were established to explain these microstructures. Here, we investigate the microstructure in a two-phase aggregate with supercritical CO2 as the fluid phase and examine the theory and model, as CO2 is different from basaltic melt in rheological properties. We conducted high‐temperature and high-pressure shear deformed experiments at 1 GPa and 1100ºC in a Griggs-type apparatus on samples made of olivine + dolomite, which decomposed into carbonate melt and CO2 at experimental conditions. After deformation, CO2 segregation and an AG-type fabric occurred in these CO2-bearing samples, inconsistency with basaltic melt-bearing samples. The SPO-induce CPO model was used to explain the formation of the fabric. Our results suggest that the influences of CO2 as a fluid phase on the microstructure of a two-phase olivine aggregate is similar to that of basaltic melt and can be explained by the CPO-formation model for the solid-fluid system.

Since the most important constituent of the cost of cryptocurrency production is energy bills, use of illegal electricity in cryptocurrency mining farms is very common. For this reason, many countries prohibit cryptocurrency production or restrict it with some legal regulations. This situation raises the problem of how to detect illicit cryptocurrency mining. Therefore, innovative approaches are needed to detect illicit cryptocurrency mining farms. In this study, it has been shown that unique noise and/or harmonic characteristics of machines producing cryptocurrency can be used to detect illicit cryptocurrency mining farms. The unique harmonic characteristics formed by data centers on neutral line have been detected by field measurements performed. Electricity distribution companies can make risk assessments with this approach by monitoring energy quality data. As a result, the necessary legal permissions can be obtained to investigate suspicious high-risk consumers. Illicit cryptocurrency mining farms can be detected by investigating at high-risk consumer facilities.

Coronavirus disease is a newly identified infectious disease that began in Wuhan, China in 2019 and is recognized as COVID-19. This virus has a serious impact on the planet that causes the deaths of millions of people; it produces unemployment and poverty. However, it has constructive environmental effects that reduce the amount of pollution in the atmosphere. Pakistan is also a developing economy caused by this deadly virus. Before 03 April 2021, the percentage of reported cases ranges from 682,888, with about 14,697 casualties and a total of 609,691 cases retrieved. Pakistan’s war against coronavirus can differ from advanced technical countries due to lack of resources. In this article, we will address the relation between COVID-19 and the environment in the particular case of Pakistan. There is evidence that this pandemic has lowered concentrations of greenhouse gases, including CO2 and NO2, as a consequence of global lock-down strategies.

In this study, a monoethanolamine aerosol growth model was developed to investigate the aerosol growth factor. Interactions among the internal conditions in an absorber were considered in this aerosol model. Additionally, an experiment was conducted to measure aerosol particle size, for collecting in-house validation data. Sucrose was used as the aerosol nuclei instead of sulfuric acid to prevent the corrosion of equipment used in the experiment. Experimental results showed that the outlet aerosol sizes increased to the same size regardless of the sucrose concentrations. The aerosol growth model was validated using the in-house experimental data. The aerosol growth model efficiently predicted the aerosol size. For investigating aerosol growth effects, particle number concentration was determined to be the primary factor affecting aerosol growth and amine emissions. When the particle number concentration increased, the aerosol size decreased, whereas the MEA emission increased.

Since 1991, there has been an alarming increase in the number of unexplained physiological events (UPEs) reported and experienced by pilots of jet fighters across different fleets. The UPEs have resulted in grounding some airframes, loss of aircraft, and even loss of life. There is no single agreed-upon root cause of UPEs that has been identified, and therefore there is no reliable corrective action. This author analyzed the literature related to other industries where artificial hyperoxic gas mixes are employed and where similar adverse reports have been reported. I hypothesize that UPEs are caused by high-dose oxygen delivery in excess of officially approved oxygen schedules while airflow rates are often inadequate, at a time when the positive pressure breathing feature of their oxygen regulator is not used. In a setting where pulmonary vital capacity is adversely affected by G-maneuvers and oxygen- and G-induced atelectasis, tidal volume is reduced by flight gear, and effective gas exchange is not supported by adequate ventilation, these factors combine to produce respiratory acidosis, followed by acute respiratory distress syndrome, CO₂ narcosis, and coma. Reports from field data related to incidents in F-18S/H, showing that emergency oxygen did not correct the hypoxia-like symptoms including long-lasting periods of incapacitation and prolonged headaches, lend support to our hypothesis.

Carbon dioxide (CO2), a major greenhouse gas, capture and separation has recently become a crucial technological solution to reduce atmospheric emissions from fossil fuel burning. Thereafter, many efforts have been put forwarded to reduce the burden on climate change by capturing and separating them especially from larger power plants by the utilization of different technologies. Those technologies have often suffered from high operating cost and huge energy consumption. On right side, physical process such as adsorption is very cost effective process which have been widely used to adsorb different contaminants including CO2. Henceforth, this review covers the overall efficacies of CO2 capture by the utilization of carbon based materials through adsorption technology. Subsequently, we also address the associated challenges and future opportunities of carbon based materials (CBMs). For CO2 capture, it was found that CBMs followed the order of carbon nanomaterials (i.e., graphene, graphene oxides, carbon nanotubes and their composites) < mesoporous -microporous or hierarchical porous carbons < biochar and activated biochar < activated carbons.

This paper examines the influence of the petrographic characteristics of sandstones from Klepa Nafpaktias (Greece) on their suitability in construction (concrete) and energy storage applications. For this scope, ten sandstones were collected in order to study their petrographic characteristics using petrographic microscope and a GIS software as well as their basic physical, mechanical and physicochemical properties. Concrete specimens (C25/30) were produced with constant volume proportions, workability, mixing and curing conditions using different sizes of each aggregate type. Aggregates were mixed both in dry and water saturated states in concrete. Three different types of sandstone aggregates were examined and classified in three district groups according to their physicomechanical properties, petrographic characteristics and surface texture. The classification in groups after the concrete compressive strength test (UCS) verified the initial classification in the same three groups relative to their grain size from coarse to fine grained. As the grain size decreases their physicomechanical and physicochemical properties are getting better resulting in higher concrete strength values (25 to 32 MPa). Furthermore, the proposed ratio C/A (crystals/ mm2) seems to influence the aggregate properties which constitute critical factors for the final concrete strength, presenting the more fine grained sandstones as the most suitable for concrete aggregates. Concerning the use of Klepa Nafpaktias sandstones as potential energy reservoirs, the studied sandstones have the appropriate physicochemical properties for the implementation of a financially feasible CO₂ capture and storage scenario.

In 2015, the new installed capacity of global renewable energy power generation exceeded the newly installed capacity of conventional energy power generation, marking a structural change in the construction of the global power system. With the continuous improvement of wind energy utilization technology, the global wind power industry has developed rapidly in recent years. The world's available wind energy is 20 billion kilowatts and has become one of the most economical green power. In China, wind power has become the third largest source of electricity, with the installed capacity increasing from 3.1% in 2010 to 9.2% in 2017. In 2017, China's new installed capacity was 19,660 MW, accounting for 37.45% of the world's new installed capacity. This paper evaluates and compares the efficiency of wind power industry in the four regions of eastern, central, western and northeastern China through EBM models based on radial and non-radial factors. This paper discusses the contribution of China's wind power industry to CO2 emission reduction from the relationship between installed capacity efficiency and CO2 emission reduction efficiency. The conclusions show that the overall efficiency score and ranking of wind power in 2013-2017 is the best in the eastern region, followed by the northeast region and the western and central regions.

Synthetic polymer-based gradient foams have considered as promising category of functionally graded materials with unique properties. In this study, the carbon dioxide (CO₂) foaming technology has used for PET-PEN (Polyethylene Terephthalate - Polyethylene Naphthalate) copolymer towards porous functional materials with thermal insulation with reasonable mechanical strength. Through scanning electron microscope based morphological characterization, a potential to fabricate gradient foam structures with micro-pores has identified. It has shown that variation of post-foaming temperature can tune the pore size distribution although the very high post-foaming temperature tends to cause structural instability. Thermal measurement data set the limits of operation, confirmed by simultaneous differential scanning calorimeter and thermo-gravimetric analysis. Mechanical stress and thermal conductivity also has measured to find rationale of thermal insulation with reasonable mechanical strength and to elucidate the actual 3D grid foam of copolymer.