There always exist steel cuttings, holes and cracks at the interfaces in the explosive composite plate. Multi-pass friction stir processing (M-FSP) is proposed in this research to optimize the interface microstructure and the interface connection for 1060Al/Q235 explosive composite plate. Results show that the microstructures of 1060Al after M-FSP are fine and uniform owing to the strong stirring effect and recrystallization. Micro-defects formed by the explosive welding can be repaired by the M-FSP. However, M-FSP can also form tunnel defects in the aluminum, especially when the passes are one and two. The melting block and the melting lump in the composite plates are easy to become source of crack. The shear strengths and the bending properties for the 1060Al/Q235 explosive composite plate after M-FSP are the best when the passes are three, with the tool rotation speed of 1200rpm and the forward speed of 60mm/min. The optimized interfaces for the explosive composite plate after M-FSP are mainly by the metallurgical bondings, with a certain thickness and are discontinuous. Therefore, the crack extension stress is the largest and the mechanical properties are the best.

This paper presents the systematic development and performance characterization of a non-proprietary 3D-printable ultra-high-performance fiber-reinforced concrete (UHPFRC) for digital construction. Several fresh and hardened properties of the developed 3D-printable UHPFRC matrix (without fiber) and composite (with 2% volume fraction of steel fibers) were evaluated and compared to that of conventionally mold-cast UHPFRC. Additionally, the effects of testing direction on the compressive and flexural strengths of the printed UHPFRC were investigated. The fresh properties of the UHPFRC developed in this study satisfied the criteria for extrudability, buildability, and shape-retention-ability, which are relevant for ensuring printability. The printed UHPFRC exhibited superior flexural performance to the mold-cast UHPFRC due to alignment of the short fibers in the printing direction. The high compressive and flexural strengths, along with the deflection-hardening behavior, of the developed UHPFRC can enable the production of thin 3D-printed components with significant reduction or complete elimination of conventional steel bars.

In this work, a xylan-based antimicrobial additive agent was prepared and aimed for uses in paper products against Escherichia coli bacteria. The derived Cationic-Xylan-grafted-PHGH (CX-g-PHGH) was successfully synthesized by graft copolymerization of cationic-xylan with guanidine polymer (PHGH) using ceric ammonium nitrate as initiator. The obtained CX-g-PHGH had maximum PHGH grafting ratio of 18.45% and efficiency of 58.45%, and showed good viscosity and thermal stability. Furthermore, the paper samples prepared in this work were reinforced obviously with the addition of CX-g-PHGH by improved mechanical properties. Compared to the reference paper without any of the xylan-derivatives, the index of tensile, tear, burst and folding endurance of the paper had increases up to 20.07%, 25.31%, 30.20% and 77.78%, respectively. Moreover, the prepared CX-g-PHGH paper exhibited an efficient antimicrobial activity against E. coli bacterial, by which a lot of applications based on the new xylan-derived additive agent obtained in this work could be found, especially in field of antimicrobial paper products against E. Coli bacteria from contaminated food.

This paper presents the microstructural and mechanical properties of low and medium carbon advanced high-strength forging steels developed based on the third generation advanced high-strength sheet steels, in conjunction with those of conventional high-strength forging steels. Hot-forging followed by an isothermal transformation process considerably improved the mechanical properties of the forging steels. The improvement mechanisms of the mechanical properties were summarized by relating to the matrix structure, the strain-induced transformation of metastable retained austenite and/or a mixture of martensite and austenite.

The parts obtained by FFF technology are anisotropic in any direction; while the whole part constitutes out of layers, each of the layers include one or more perimeters of shell and the infill with density from 0 to 100%. Mechanical performance of FFF parts depends on its shape, orientation, constitution and 3D printing parameters. A classification for shapes of parts obtained by FFF and stressed during its operation is provided. For the most questionable class (parts with interrupted shell critically stressed on interlayer boundaries) a representative sample and testing apparatus is developed. Different approaches to the sample shape modification were applied and tested. The part shape optimization resulted in increment of the force, required to fracture the part from 483 to 1096 N.

Foam concrete is a construction material with controllable low strength and untraditional physical properties. Its highly crushable nature leaves it a niche as an engineered energy-absorbing material in many value-added applications; however, fundamental understanding of the material properties is crucial. As foam concrete is highly cellularized and ductile, conventional concrete testing methods such as compression test are insufficient to characterize the key material attributes of foam concrete, especially when the foam density is low. The resonant frequency test (ASTM C215) is specified for evaluating dynamic Young’s modulus of normal concrete. Inspired by the non-destructive feature of this test, we investigate the possibility of using the resonant frequency test to continuously monitor the modulus build-up of foam concrete with age. For the representativeness of the samples, three variables are considered in material design—bulk density ranging from 0.4 to 1.2 g/cm3, water to cementitious materials ratio of 0.42 and 0.47, and fly ash replacement of 10 and 30% by weight of cement. After examining the different vibration modes, the fundamental transverse frequency is determined most suitable for interpreting the foam modulus. The experimental results demonstrate good accuracy of using this approach for the measurement of different samples. It is also confirmed that, for a given foam concrete, the foam modulus can be predicted by knowing the foam density and solid modulus of its base cement paste, which provides an important insight for the further studies and real applications of foam concrete.

The USDA-FSIS considers mechanically-tenderized beef as ‘non-intact’ and a food safety concern because of the potential for translocation of surface E. coli O157:H7 into the interior of the meat that may be cooked ‘rare or medium-rare’ and consumed. We evaluated 14 potential spray interventions on E. coli O157:H7-inoculated lean beef wafers (~10⁶ CFU/cm² , n=80) passing through a spray system (18 sec dwell time, ~40 PSI) integrated into the front end of a Ross TC-700MC tenderizer. Inoculated and processed beef wafers were stomached with D/E neutralizing broth and plated immediately, or were held in refrigerated storage for 1-, 7-, or 14 days prior to microbial plating. Seven antimicrobials that showed better performance in preliminary screening on beef wafers were selected for further testing on beef subprimals in conjunction with blade tenderization. Boneless top sirloin beef subprimals were inoculated at ~2 x 10⁴ CFU/cm² with a four-strain cocktail of Escherichia coli O157:H7 and passed once, lean side up, through an integrated spray system and blade tenderizer. Core samples obtained from each subprimal were examined for the presence/absence of E. coli O157:H7. Absence of E coli O157:H7 translocated into core samples correlated with the ability of the antimicrobials to reduce bacterial levels on the surface of beef prior to blade tenderization.

Dispersed silver nanoparticles (AgNPs) on the surface of titanium alloy (Ti6Al4V) and titanium alloy modified by titania nanotube layer (Ti6Al4V/TNT) substrates were produced by chemical vapor deposition method (CVD) using novel precursor of the formula [Ag₅(O₂CC₂F₅)₅(H₂O)₃]. The structure and volatile properties of this compound were determined using single crystal X-ray diffractometry, variable temperature IR spectrophotometry (VT IR), and electron inducted mass spectrometry (EI MS). The morphology and the structure of the produced Ti6Al4V/AgNPs, and Ti6Al4V/TNT/AgNPs composites were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Moreover, measurements of hardness, Young’s modulus, adhesion, and surface free energy have been carried out. The ability to release silver ions from the surface of produced nanocomposite materials immersed in PBS solution has been estimated using inductively coupled plasma mass spectrometry (ICP MS). The wettability and the surface free energy of samples were estimated on the base of contact angle studies with the use of water and diiodomethane. Among the studied surface-modified titanium alloy implants, the best nano-mechanical properties were noticed for the Ti6Al4V/TNT15/AgNPs composite. The location of silver nanoparticles inside of titania nanotubes caused their lowest release rate, which may indicate on suitable properties above mentioned type of the composite for the construction of implants with a long term of antimicrobial activity.

Micro-technology has played a substantial role in bioscience, biomedical and biotechnological research due to its core advantages in modern science and engineering. It has created unique development in various sectors of bio-research and upsurges the efficacy of research at the molecular level in recent years. Microfluidic technology makes it possible to manipulate sample volumes at the micro- and nano-level (called nanofluidics) with terrific control outside in vivo cellular microenvironment, enabling the reduction of discrepancies between in vivo and in vitro environments as well as reducing reaction time and cost. In this review, we discuss various effective integrations of microfluidic technologies into biotechnology and its paradigmatic significance in bio-research, supporting mechanical and chemical in vitro cellular micro-environment. Specific innovations relating to the application of microfluidics to advance microbial life, solitary and co-cultures along with a multiple-type cell culturing, cellular communications, cellular interactions and population dynamics are discussed.

Failure characteristics induced by unloading disturbance and the corresponding mechanical mechanism of the coal seam floor are important theoretical bases for water-bursting prevention from the floor of the coal seam and rock burst alarm in deep mining. However, the existing two-dimensional ground-pressure-control theory based on shallow mining cannot sufficiently guide deep-mining practices. In this study, the redistribution of mining-induced stress field in rocks surrounding the longwall face and mechanical behaviors of strata in deep mining are investigated through a combination of numerical simulation, physical simulation, and field measurement. Results demonstrate that mining-induced stress fields in the floor of the longwall face differ in space and time. Vertical stress unloading from top to bottom of the floor and horizontal stress unloading are relatively low. A concentration zone of high horizontal stress exists at stope boundaries. The critical yield load of rock stratum in the floor is determined through thin plate yield theory. Under the combined effect of concentrated high horizontal and vertical resilience stresses, strata in the floor fracture from seam to seam if the load increases to the minimum critical buckling value. Fractured strata slide along the fracture surface, which leads to floor heave. The stope floor shows evident time-delay progressive failure characteristics. The stress shell in the stope floor in deep mining is found to be a sensitive mechanical parameter that produces three-dimensional ground-pressure behavior in the floor. This ground-pressure behavior in the stope floor is controlled by the existence of the corresponding stress shell and effects induced by its space–time evolution. This study provides theoretical basis for the dynamic control of a hazard-inducing environment in engineering and minimizing or altering disaster-occurrence conditions during the construction engineering of the coal seam floor.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

The growing requirements regarding the safety of using polymers and their composites are related to the emergence of more effective, sustainable, and hazardous-limited fire retardants (FR). Significant amounts of FR are usually required to effectively affect the polymer burning behavior, while the knowledge of their recycling potential is still insufficient. At the same time, concerns are related not only to the reduced effectiveness of flame retardancy but, above all, to the potential deterioration of mechanical properties caused by the degradation of temperature-affected additives under processing conditions. This study describes the impact of four-time reprocessing of bio-based polyamide 11 (PA11) modified with an intumescent flame retardant (IFR) system composed of ammonium polyphosphate (APP), melamine cyanurate (MC) and pentaerythritol (PER) and its composites containing additionally short basalt fibers (BF). Composites manufactured by twin-screw extrusion were subjected to four reprocessing cycles by injection molding, comprehensively analyzing structural, mechanical, and fire behavior changes in each cycle. The obtained results confirmed the safety of using the proposed flame-retardant system for polyamide, processed under the recommended process parameters, without the risk of significant changes in the structure despite the partial increase in flammability caused mainly by the degradation of the polymer.

This paper designed a new type of generator, transgenerator, that integrates the wind turbine and flywheel into one system, aiming to make the flywheel distributed energy storage (FDES) more modular and scalable than the conventional FDES. The transgenerator is a three-member dual-mechanical-port (DMP) machine with two rotating members (inner and outer rotors) and one stationary member (stator). The transgenerator-flywheel system is introduced with the system configuration, transgenerator overview, flywheel operation principle and power management strategies, and control system. Simulations are performed in MATLAB/ Simulink to verify the system viability, including control system verification and the flywheel storage performance evaluation. Results show that the inner and outer rotors can be controlled independently with accurate and fast control response, and the grid-side control works properly. The flywheel performs well with considerable charging power and storage capacity.

The objective of this paper is to investigate the debonding behavior of the interface between continuously and discontinuously fiber reinforced thermoplastics using the climbing drum peel test. The study emphasizes the importance of considering different climatic boundary conditions due to the properties of thermoplastics. Specimens with varying moisture contents are prepared and tested. It is observed that an increase in moisture content initially results in a higher fracture surface energy being required to separate the two materials, but a further increase results in a decrease of the required energy. The study presents an explanatory model of increasing plasticization of the polymer due to increased polymer chain mobility, which results in more deformation energy being required to propagate the crack. The experiment is also modeled numerically for the first time with cohesive surfaces, which successfully reproduces the force-displacement curve in the experiment.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

The prohibitive costs of small-scale solar photovoltaic (PV) racks decreases PV adoption velocity. To overcome these costs challenges, an open hardware design method is used to develop two novel variable tilt racking designs. These are the first stilt mounted racking designs that allow manual change of tilt angle from zero to 90 degrees by varying the length of cables. The racks are designed using the calculated dead, wind and snow loads for Canada as conservative design for most of the rest of the world. Structural capacities of the wooden members are then ascertained and resisting bending moment, shear force, tensile force, and compressive force for them is calculated. A structural and truss analysis is performed to ensure that racking design with-stands the applicable forces. Moreover, implications of changing the tilt angle on the wooden members/cables used to build the system are also determined. The systems offer significant economic savings ranging from 1/3rd to 2/3rd the capital expenses of the commercially available alternatives. In addition, the racking designs are easy-to-build and require minimal manufacturing operations, which increases their accessibility. The stilt-mounted designs can be employed for agrivoltaic settings while allowing farm workers shaded ergonomic access to perform planting, weeding, and harvesting.

There has been controversy around the mechanical properties of Mg-alloys such as AZ91D and the large variation of these have been seen. The current paper addresses this controversy through specially fabricated samples combined with tensile testing and advanced metallography, including 3D reconstruction of the phases. The results show that despite a more brittle nature of the fracture, the equiaxed microstructure displays a better elongation as compared to a dendritic microstructure. The main conclusion is that this is primarily caused by the nature, or tortuosity, of the Mg17Al12-network in the material.

Generally, mineral fillers are added to thermoplastic polymers to reduce cost and improve performance. However, properly selected mineral fillers can also improve thermal conductivity and deformation behavior, shrinkage, impact strength, dimensional stability, and molding cycle time in thermoset polymers. This study focused on the preparation and microscopic and spectroscopic characterization of various hybrid composites using pumice as primary filler and gypsum, kaolin and hollow glass sphere as secondary fillers, as well as examining some of their mechanical properties and thermal conductivities. For this, first of all, surface modification of the clay was carried out by intercalation method from solution using raw Montmorillonite, cationic surfactant and long chain hydrocarbon material, and then organo-clay melamine formaldehyde nanocomposite was prepared by in situ synthesis using organo clay and melamine formaldehyde pre-polymer. Finally, non-ionic surfactant, foaming agent and glycerin were added to the prepared nano-composite at approximately 90°C, mixed mechanically and then pumice was added. The processes at this stage were repeated while preparing hybrid composites with pumice and other mineral additives. For curing and molding, the composite was first subjected to microwave irradiation for 5 minutes followed by thermal treatment at 140°C for 60 min. Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD) spectra and Scanning electron microscope (SEM) and High resolution transmission electron microscope (HRTEM) images were taken for morphological and textural characterization for raw clay (MMT), organo clay (OMMT) and pure polymer with prepared hybrid composites. In addition, some mechanical properties such as bending strength, elasticity modulus and screw holding resistance, as well as thermal conductivity coefficients of the hybrid composites were determined according to the relevant standards and the obtained results were evaluated. Spectroscopic and microscopic analyzes have shown that effective adhesion interactions occur between polymer-clay nanocomposite particles and filler grains, thus resulting in textural arrangements with different properties. Mechanical and thermal conductivity test results showed that melamine formaldehyde-organo-clay nano composite foam and hybrid composite containing hollow glass sphere are highly qualified materials in terms of thermal insulation and mechanical strength.

To weaken the harm of Al-Si coating and increase the strength of welded joint, variable thickness of Ni foil (Ni, an austenitic formation element) was added into the lap laser welding Al-Si coated 22MnB5 hot stamping steel/galvanized steel joints. The joints' weld appearance, microstructure, and mechanical properties were explored. The weld altered from X-shape to Y-shape with the increased thickness of Ni foil. During welding, Al-Si coating was melted and diluted into the welding pool, forming δ-ferrite (a rich-Al phase with low toughness and strength) in FZ and FB. This phase deteriorated the strength of the joints. After adding Ni, the amount and size of the δ-ferrite phase decreased. With a significant thickness of Ni foil, δ-ferrite would disappear. However, a new phase (FM, rich-Ni phase) probably formed except PM(a no or negligible Ni phase). The heat-affected zone (HAZ) on the side of 22MnB5 comprised a coarse martensite zone, refined martensite zone, martensite+ferrite zone, and tempered martensite zone from the FZ to the basic material. HAZ on the side of galvanized steel mainly contained ferrite and pearlite. After adding Ni foil, the strength of the joint was more than that without Ni. The maximum strength of the joint can be up to 679MPa because of the disappearance of δ-ferrite. Meanwhile, the toughness of the joint increased. The fracture mode was from three mixed fractures(cleavage, quasi-cleavage, and dimple) to one fracture(dimple).

In this study, an extensive data set was based on existing literature records in order to enable the suitability of several predictive models, from Multiple Linear Regression (MLR) to Neural Networks (NN). The main objective was to, through regression analyses, generate model computations to correlate tensile properties (UTS- Ultimate Tensile Strength, YTS – Yield Tensile Strength and EF – Elongation-to-Fracture) to a given alloy composition and microstructural spacing. This investigation led to positive results, as the highest accuracies of the trained modules (in 80% of the database) were found to be above ~82% (UTS and EF) and a maximum of ~98% (YTS), when analyzing the results to a test data set. Later, these models were used to define trends for possible next solder alloy commercial compositions. Overall, using the standard model’s setup, the Random Forest and Decision Tree models showed the highest accuracy results, with 0.958 for YTS as opposed to 0.907 for MLR. Moreover, Multilayer Perceptron (MLP)-optimized models yielded the best results for each variable, with the highest increases in accuracy associated with the YTS and EF. The present contribution might imply an important milestone towards alloy design research based on data science guidelines to unlock the full potential of former experiments and their extensive set of results.

During submerged laser peening using a pulsed laser, a bubble that behaves like cavitation is generated after laser ablation (LA). The bubble is referred to as laser cavitation (LC). The amplitude of the shock-wave in LA water is larger than that of LC; however, the impact passing through the target metal during LC is larger than that of LA. Thus, submerged laser peening is referred to as “laser cavitation peening”, as the peening method using the cavitation impact is known as “cavitation peening”. The impact induced by a hemispherical bubble is more aggressive than that of a spherical bubble with a microjet. Laser cavitation peening can improve the fatigue strength of metallic materials by producing work-hardening and the introduction of compressive residual stress. Three-dimensional additive manufactured metals (3D metals) such as titanium alloy are attractive materials for aviation components and medical implants; however, the fatigue strength of as-built components is nearly half that of bulk metals, and this is an obstacle for the applications of 3D metals. In the present study, published research papers were reviewed to identify the key factors of laser cavitation peening, with additional visualization of LC and data. Then, improvements in the fatigue strength of metallic materials, including 3D metals produced by laser cavitation peening, were summarized.

To study the feasibility and effect of compounding lignin and its derivatives to improve expansive soil, the physical properties, mechanical properties, and microstructure of the improved soil mixed with calcium lignosulfonate alone, calcium lignosulfonate and lignin fibers were investigated through indoor experiments and electron microscope scanning. Select samples with better performance for water stability tests, and discuss the improvement mechanism of expansive soil by combining macroscopic mechanical changes with microstructural characteristics. The research results show that the addition of calcium lignosulfonate can reduce the water content of the soil and enhance its strength of the soil. The overall performance is the best when the calcium lignosulfonate content is 3%. 3% calcium lignosulfonate compounded with 1.5% lignin fiber has the best all-around performance; the composite improved soil has a better pore-filling effect, the whole is more compact, and the connection between particles significantly enhances the strength, which greatly inhibits the development of cracks good water stability. Lignin and its derivatives compound improved expansive soil have better effect than traditional improvement methods, and have no pollution to the environment, which can provide a particular reference for engineering practice

To study the feasibility and effect of compounding lignin and its derivatives to improve expansive soil, the physical properties, mechanical properties, and microstructure of the improved soil mixed with calcium lignosulfonate alone, calcium lignosulfonate and lignin fibers were investigated through indoor experiments and electron microscope scanning. Select samples with better performance for water stability tests, and discuss the improvement mechanism of expansive soil by combining macroscopic mechanical changes with microstructural characteristics. The research results show that the addition of calcium lignosulfonate can reduce the water content of the soil and enhance its strength of the soil. The overall performance is the best when the calcium lignosulfonate content is 3%. 3% calcium lignosulfonate compounded with 1.5% lignin fiber has the best all-around performance; the composite improved soil has a better pore-filling effect, the whole is more compact, and the connection between particles significantly enhances the strength, which greatly inhibits the development of cracks good water stability. Lignin and its derivatives compound improved expansive soil have better effect than traditional improvement methods, and have no pollution to the environment, which can provide a particular reference for engineering practice.

Solar powering the increasing fleet of electrical vehicles (EV) demands more surface area than may be available for photovoltaic (PV) powered buildings. Parking lot solar canopies can provide the needed area to charge EVs, but are substantially costlier than roof- or ground-mounted PV systems. To provide a lower-cost PV parking lot canopy to supply EV charging beneath them, this study provides a full mechanical and economic analysis on three novel PV canopy systems: (1) exclusively wood, single parking spot spanning system, (2) wood and aluminum double parking spot spanning system, and (3) wood and aluminum cantilevered system for curbside parking. All systems can be scalable to any amount of EV parking spots. The complete designs and bill of materials (BOM) of the canopies are provided along with basic instructions and are released with an open source license that will enable anyone to fabricate them. The results found single-span systems have cost savings of 82%-85%, double-span systems save 43%-50%, and cantilevered systems save 31%-40%. In the first operation year, the PV canopies can provide 157% of energy needed to charge the least efficient EV currently on the market if it is driven the average driving distance in London ON, Canada.

Various metals and semiconductors containing Printed Circuit Boards (PCBs) are abundant in any electronic device equipped with controlling and computing features. These devices inevitably constitute E-waste after the end of service life. The typical construction of PCBs includes mechanically and chemically resistive materials, which significantly reduce the reaction rate or even avoid accessing chemical reagents (dissolvents) to target metals. Additionally, the presence of relatively reactive polymers and compounds from PCBs requires high energy consumption and reactive supply due to the formation of undesirable and sometimes environmentally hazardous reaction products. Preliminarily milling PCBs into powder is a promising method for increasing the reaction rate and avoiding liquid and gaseous emissions. Unfortunately, current state-of-the-art milling methods also lead to the presence of significantly more reactive polymers still adhered to milled target metal particles. This paper aims to find a novel single and two-stage disintegration-milling approach that can provide the formation of metal-rich particle size fractions. The morphology, particle fraction sizes, bulk density, and metal content in produced particles were measured and compared. Research results show the highest bulk density (up to 6.8 g·cm-3) and total metal content (up to 95.2 wt. %) in finest sieved fractions after the single-step milling of PCBs. Therefore, the concentrations of about half tested metallic elements are higher in the single milled specimen and with lower adhered plastics concentrations, as compared to double milled specimens.

To verify the authors’ mathematical model for water jet cooling of steel sheet, the previously performed experimental studies of temperature of the test plate in the roller quenching machine (RQM) were used. The calculated data of steel temperature evolution along the RQM length were compared with the readings of thermocouples inserted in the center of the test plate and at its surfaces. The core of the model is the dependence of the temperatures of film, transition and nucleate boiling regimes on the thickness of the oxide scale layer on the cooled surface. It was found that the model correctly takes into account the oxide scale on the sheet surface, flow rates and combinations of the RQM banks used, water temperature and other factors. For all experiments the calculated metal temperature corresponds well to the measured one. In the experiments with interrupted cooling, the calculated temperature plots repeat the characteristic changes in the experimental curves. The main uncertainty in the modeling of cooling in a wide temperature range can be contributed by the random nature of changes in the oxide scale thickness during water cooling. In this regard, the estimated thickness of the oxide scale layer should be considered as the main parameter for adapting the sheet temperature control process. The obtained data confirm the possibility of effective application of the model in the ACS of industrial TMCP (Thermo-Mechanical Controlled Process) systems.

Ceramic samples based on b-calcium pyrophosphate b-Ca2P2O7 were prepared using firing at 900, 1000, and 1100 oC from powders of g-calcium pyrophosphate g-Ca2P2O7 with preset molar ratios Ca/P=1; 0,975 and 0,95. To prepare powders of g-calcium pyrophosphate g-Ca2P2O7 with preset molar ratio Ca/P=1; 0,975 and 0,95 powder mixtures based on calcium lactate pentahydrate Ca(C3H5O3)2⋅5H2O and, monocalcium phosphate monohydrate Ca(H2PO4)2⋅H2O were treated in an aqua medium in mechanical activation conditions, dried, disaggregated in acetone, and heat-treated at 600 oC. The phase composition of powder mixtures after treatment if planetary mill in aqua medium included both brushite CaHPO4⋅2H2O or monetite CaHPO4, and starting salts. The phase composition of all powder mixtures after disaggregation in acetone in planetary mill included monetite CaHPO4 and starting salts. After heat treatment at 600 oC according to the XRD data phase composition of all powder mixtures was presented by g-calcium pyrophosphate g-Ca2P2O7. The grain size of ceramics increased both with the growth of firing temperature and with decreasing of molar ratio Ca/P of powder mixtures. Calcium polyphosphate (t melt =960–968 oC) formed from monocalcium phosphate monohydrate Ca(H2PO4)2⋅H2O acted like a liquid phase sintering additive. It was confirmed by tests in vitro, that prepared ceramic materials with preset molar ratio Ca/P=1; 0,975 and 0,95 and phase composition presented by b-calcium pyrophosphate b-Ca2P2O7 according to XRD data were biocompatible and could maintain bone cells proliferation.

In this paper, 6063 aluminum alloy for common building profiles is used as the research object. By adding a new Al-Ti-C-La composite alloy, the effect of 6063 aluminum alloy on the microstructure and properties of 6063 aluminum alloy is studied. The results show that Al-Ti-C-La composite alloy has obvious effect on grain refinement of 6063 aluminum alloy. With the addition of Al-Ti-C-La composite alloy, the grain size decreased significantly. When the addition amount of Al-Ti-C-La composite alloy is 1%, the grain size is reduced from 482 μm to 121 μm. Rare earth La is mainly distributed near the Mg2Si phase and β-AlFeSi, and complex compounds such as AlFeSiMgLa are formed. After aging for 270 days on the basis of T6 heat treatment, the tensile strength and elongation of 6063 aluminum alloy augmented with the addition of Al-Ti-C-La composite alloy, and the Vickers hardness gradually diminished. When the addition amount of Al-Ti-C-La composite alloy is 1%, the tensile strength, elongation and Vickers hardness of 6063 aluminum alloy reach 177.2 MPa, 17.8% and 60.9 HV, respectively, and the tensile strength is increased by 16.3%. The elongation is increased by 50.8%, the Vickers hardness is reduced by 15.4%, and the fracture of the alloy is mainly ductile fracture.

There is an increase towards reducing the weight of structures through the use of aluminium alloys in different industries like aerospace, automotive, etc. This growing interest would lead towards using dissimilar aluminium alloys which would require welding. TIG and friction stir welding are the well-known techniques that are currently suitable for joining dissimilar aluminium alloys. The welding of dissimilar alloys has its own dynamics which impact on the quality of the weld. This then suggests that there should be a process which can be used to improve the dissimilar alloys welds post their production. Friction stir processing is viewed as one of the techniques that could be used to improve the mechanical properties of the material. This paper reports on the status and the advancement of FSW, TIG and FSP technique. It further looks at the variation use of FSP on TIG and FSW welded joints with the purpose of identifying the knowledge gap.

Materials design for processing and application requires fundamental understanding of their properties based interatomic interaction. The use of the novel concept of total bond order density (TBOD) as a single quantum mechanical metric to characterize the internal cohesion of a crystal and correlate with the calculated physical properties is particularly appealing. This requires detailed first-principles calculation of the electronic structure, interatomic bonding and related properties. In this article, we use this new concept and apply it to chalcogenide crystals based on data obtained from 25 crystals: Ag₂S, Ag₂Se, Ag₂Te, As₂S₃, As₂Se₃, As₂Te₃, As₄Se₄, Cu₂S, Cu₂Se, Cu₂Te, Cu₄GeS₄, Cu₂SnS₃, Cu₂SnSe₃, GeS₂, GeSe₂, Ge₄Se₉, Sb₂S₃, Sb₂Se₃, Sb₂Te₃, SnS, SnSe, CdSe, CdTe, ZnSe, and ZnTe. Together with the calculated optical and mechanical properties, we demonstrate the efficacy of using this novel approach for materials design that could facilitate the exploration and development of new chalcogenide crystals and glasses. Moreover, the TBOD and its partial components (PBOD) could be the key descriptors in machine learning protocol for broader scale design when a large database is available.

Water soluble polymers have gained an increasing interest in enhanced oil recovery (EOR) processes, especially as polymer flooding. Despite the fact that the flow of polymer in porous medium has been a research subject for many decades with numerous publications, there are still some research areas that need progress. The prediction of polymer injectivity remains elusive. Polymers with similar shear viscosity might have different in-situ rheological behaviors and may be exposed to different extent of mechanical degradation. Hence, determining polymer in-situ rheological behavior is of great significance for defining its utility. In this study, an investigation of rheological properties and mechanical degradation of different HPAM (partially hydrolyzed polyacrylamide) polymers was performed using Bentheimer sandstone outcrop cores. Results show that, HPAM in-situ rheology is different from bulk rheology measured in rheometer. Specifically, shear thickening behavior occurs at high rates, and near-Newtonian behavior is measured at low rates in porous media. This deviates strongly from measurements in the rheometer. Polymer molecular weight and concentration influence its viscoelasticity and subsequently its flow characteristics in porous media. Exposure to mechanical degradation by flow at high rate through porous media leads to significant reduction in shear thickening and thereby improved injectivity. More importantly, the degraded polymer maintained in-situ viscosity at low flow rates indicating that improved injectivity can be achieved without compromising viscosity at reservoir flow rates. This is explained by reduction in viscoelasticity. Mechanical degradation also leads to reduced residual resistance factor (RRF), especially for high polymer concentrations. For some of the polymer injections, successive degradation (increased degradation with transport length in porous media) was observed. The results presented here may be used to optimize polymer injectivity.

The use of commodity polymers such as polypropylene (PP) is key to open new market segments and applications for the additive manufacturing industry. Technologies such as powder-bed fusion (PBF) can process PP powder; however, much is still to learn concerning process parameters for reliable manufacturing. This study focusses in the process-property relationships of PP using laser-based PBF. The research presents an overview of the intrinsic and the extrinsic characteristic of a commercial PP powder as well as fabrication of tensile specimens with varying process parameters to characterize tensile, elongation at break, and porosity properties. The impact of key process parameters, such as power and scanning speed are systematically modified in a controlled design of experiment. The results were compared to the existing body of knowledge; the outcome is to present a process window and optimal process parameters for industrial use of PP. The computer tomography data revealed a highly porous structure inside specimens ranging between 8.46% and 10.08%, with porosity concentrated in the interlayer planes in the build direction. The results of the design of experiment for this commercial material show a narrow window of 0.122 ≥ Ev ≥ 0.138 J/mm³ led to increased mechanical properties while maintaining geometrical stability.

A potassium bromide KBr material, which has been widely used as the key element in the Fourier spectrometers and as the output window of the IR-lasers, has been studied with good advantage via applying the carbon nanotubes in order to modify the potassium bromide surface. The laser oriented deposition method has been used to place the carbon nanotubes at the matrix material surface in the vertical position at the different electric field varied from 100 to 600 V×cm-1. The main idea of the improvement of the spectral properties of the potassium bromide structure is connected with the fact that the refractive index of the carbon nanotubes is substantially less than the refractive index of the studied material, and the small diameter of the carbon nanotubes allows one to embed these nano-objects in the voids of the lattice of the model matrix systems. Moreover, the mechanical characteristics and wetting features of the potassium bromide structures have been investigated under the condition mentioned above. Analytical and quantum-chemical simulations have supported the experimental results.

A new type of low cost, environmentally friendly wood-plastic composites (WPC) containing carbon nanotubes(CNT)of low content 0%, 0.05wt%, 0.1wt% and 0.15wt%, wood fibers of 14wt% and polymer PES of 86wt% was manufactured by the selective laser sintering (SLS) approach of 3D printing. The experimental results showed that the incorporating of CNTs could obviously increase the mechanical properties of the wood/PES composites material. The tensile strength, bending strength and elasticity modulus were 76.3%, 227.9% and 128.7% higher with 0.1wt% CNTs than without CNTs. And the mechanical properties of specimens firstly increased and then decreased with the increasing contents of CNTs. The SEM results of the specimens’ fracture morphology indicated that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons to explain why the composites possessed the superior mechanical properties: CNTs could facilitate the laser sintering process of wood plastic composites due to their thermal conductivities; also, CNTs could directly reinforce the WPC composites as reinforcement.

With the ever-growing emphasis on global decarbonization and rapid increases in the power density of electronics equipment in recent years, new methods and lightweight materials have been developed to manage heat load as well as interfacial stresses associated with Coefficient of Thermal Expansion (CTE) mismatch between components. The Al-Si system provides an attractive combination of CTE performance and high thermal conductivity whilst being a very lightweight option. Such materials are of interest to industries where thermal management is a key design criterion, such as aerospace, automotive, consumer electronics, defense, EV and space. This paper will describe the development and manufacture of a family of high-performance hypereutectic Al-Si alloys (AyontEX™) by a powder metallurgy method. These alloys are of particular interest for structural heat sink applications that require high reliability under thermal cycling (CTE of 17μm/(m·°C)) as well as reflective optics and instrument assemblies that require good thermal and mechanical stability (CTE of 13μm/(m·°C)). Critical performance relationships are presented, coupled with the microstructure, physical and mechanical properties of these Al-Si alloys.

This paper proposes a lightweight joint with bamboo culm cross connection, which is constructed by screwing one side of the screw into the other side of the wooden plug, its simple construction makes it easy to manufacture and cost-effective. This form connects adjacent bamboo culms to form corner joints, and bolt connects adjacent bamboo culm frames to form edge joints, to explore the mechanical properties of the combination joints formed by corner joints and edge joints, by combining experiments and numerical simulations, the method discovered and explained the relationship and mechanism between the number and position of bolts and the stiffness of edge joints. A calculation model for frame-unit bamboo culm members considering semi-stiffness of joints is proposed, and the conversion equations between linear stiffness of corner and edge joint and their rotational stiffnesses are derived. By establishing the series and parallel relationship between the corner and edge joints in the assembled members, a generalized relational equation between the total stiffness of the assembled joint and the stiffness of the corner and edge joints is derived. A numerical simulation method for frame-unit bamboo culm members with semi-rigid joints is proposed, which can obtain the stiffness calculation formula of edge joints and the average rotational stiffness value of semi-rigid corner joints. A finite element analysis method based on semi-rigid joints is proposed for frame-unit bamboo culm members, and the internal force sketches and calculation methods for bamboo culms and joints are presented, which can be used for the internal force analysis and design of frame-unit bamboo culm lattice structures.

Electrospun fiber scaffolds are widely used in small diameter vascular tissue engineering because they mimick organizational structure and biological function of natural extracellular matrix. However, there is still one problem of low patency rate in the long term. The main reasons are the mismatch of compliance and the easy formation of thrombus. Therefore, it is very important to promote the rapid endothelialization of small diameter tissue engineering blood vessels by regulating the topological structure and biological properties of electrospun fiber scaffolds. Firstly, crimped polylactic acid (PLA) fibers were prepared by heat treatment to mimick the crimped structure and nonlinear mechanical properties of the elastic membrane of blood vessel wall. It improved effectively the aspect ratio of human umbilical vein endothelial cells (HUVECs) and promoted lateral alignment and growth. Then, crimped PLA fibers with three levels of pore structure were prepared by thermal induced phase separation, vapor induced phase separation and laser ablation to enhance the degree of HUVECs infiltrarion and realize patterned cell growth. Crimped PLA fibers with three levels of pore structure promote rapid endothelialization of blood vessels, which is of great significance to achieve long term patency rate of small diameter tissue engineering blood vessels.

Although solar photovoltaic (PV) system costs have declined, capital cost remains a barrier to widespread adoption. Do-it-yourself (DIY) system designs can decrease costs by about 50% by reducing labor costs, but if not attached to a building structure demand ground penetration for conventional footings. This is not technically and economically feasible at all sites. To overcome these challenges, this study details systems designed to eliminate drilling holes and pouring concrete. Two different designs for both fixed tilt and variable tilt PV racking are investigated to assess their structural integrity, constructability, and economic cost when fabricated with a ballast-supported foundation. The ballast-supported foundations are analyzed for eight such systems by proposing two separate ballast designs: one for single line of post systems, and one for double line of post systems built on a 4-kW basis. The results of the analysis found that both designs are slightly more expensive than typical in-ground concrete systems by 25%, but the overall DIY systems costs remain economically advantageous. Sensitivity analyses are conducted to show how modifications to the dimensions including clearances and distances between gabions influence the weight of the system and thus change the economic value of the design, so users can trade dimensional freedom for cost-savings, and vice versa. Overall, all the wood-based PV racking system designs provide users with cost-effective and easy DIY alternatives to conventional metal racking, and the novel ballast systems presented provide more versatility for PV systems installations.

This work explores five falling film evaporator (FFE) simulation approaches combined with energy consumption minimization strategies, namely Mechanical Vapor Recompression and Thermal Vapor Recompression (MVR and TVR respectively). Global system analysis and advanced dynamic optimization strategies are then investigated to minimize steam consumption, the cost of steam, the total annualized cost and maximizing product yield. The results indicate that a higher TVR discharge pressure, or MVR compression ratios, along with higher feed temperatures enhance evaporation with but increase operational costs. The most economic option includes three evaporator effects with TVR for achieving 50% product dry mass content. However, for a 35% dry mass content, MVR becomes cost-effective with an 11% reduction in unit electricity prices or a simultaneous 7% drop in electricity prices and a 5% increase in gas-based steam prices. Furthermore, switching from milk powder production to milk concentrates, an annual cost reduction ranging from 10.75 to 44% is achieved. Also, a forecasted 20% (or more) reduction of biomass-based steam cost can lead to lower annual expenditure comparing with the nominal NG-based steam Case. Regarding the total annualized cost, for a new plant design, optimization strategies lead to a 9 - 45% reduction in the total cost depending on the Case under consideration.

This study examines the impact of the impregnation of fireclay-based conventional (CC) and medium cement castables (MCC) with liquid sodium silicate glass under vacuum conditions. The goal is to assess how this treatment affects physical, mechanical properties, and durability (alkali and thermal shock resistance) of these castables used in biomass combustion boilers, where they are exposed to temperatures up to 1100°C. The research work employs standard test methods to evaluate physical and mechanical properties. Additionally, advanced techniques such as scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and specific tests for alkali resistance and thermal shock resistance are used. The research findings suggest that impregnation with sodium silicate glass under vacuum significantly enhances the alkali resistance of both CC and MCC castables. This improvement is primarily due to the reduction in porosity and the increase in density. SEM images reveal that impregnated samples are coated with a glassy layer and the pores are partially filled with sodium silicate. Tests for alkali resistance demonstrate the formation of a protective glassy layer (with a thickness of 0.9-1.5 mm) on the castables surfaces, thereby reducing further penetration of alkali into deeper layers of the samples. However, it is important to mention that impregnated refractory castables have reduced resistance to thermal shock cycles.

The most modern technique utilized to create intricate and complexly manufactured parts for a variety of applications is called additive manufacturing (AM). Fused deposition modeling (FDM) has received the greatest attention in the development and manufacturing sectors. The main objective of this study was to investigate how printing factors affected the mechanical characteristics of printed samples. Samples were produced using an FDM 3D printer in compliance with ASTM D638 using a variety of input settings, including orientation, layer thickness, speed, and infill pattern. On the printed samples, tensile tests and morphological analysis using a scanning electron microscope (SEM) were done. The findings of this study demonstrate that factors including layer thickness, printing speed, and orientation significantly affect the tensile strength of ABS printed samples. Discovering the process settings that could lead to superior mechanical and physical characteristics would undoubtedly assist designers and manufacturers worldwide as the FDM 3D printer becomes more and more crucial in manufacturing engineering parts.

Background: Number of joint infections caused by Vancomycin-resistant pathogens is emerging. Currently no PMMA cement is commercially available to cover VRE. Daptomycin shows promising results in infection treatment, offers a good safety profile and reduced risk for resistance development. Purpose of this in vitro study is to investigate the mechanical stability, handling properties, elution behavior and antimicrobial effectiveness of PMMA cement loaded with three different Daptomycin concentrations in comparison to commercially available ALBC; Methods: Mechanical properties and handling characteristics (ISO 5833, DIN 53435), HPLC elution, antimicrobial effectiveness with proliferation assay (DIN 17025) and inhibition zone testing were investigated; Results: All tested Daptomycin concentrations fulfilled ISO and DIN mechanical strength. Dosage of 0.5. g added Daptomycin did not show any antimicrobial effectiveness in contrast to 1.0 g and1.5 g. Cement with 1.5 g Daptomycin was best in elution and effectiveness, showed good mechanical ISO strength, ISO doughing was a little longer sticky and setting was faster as Vancomycin containing reference cement; Conclusion: PMMA cement containing 0.5 g Gentamicin and 1.5 g Daptomycin could be a good alternative to the already established COPAL® G+V for PJI treatment of VRE.

This research examines the fire resistance of geopolymer composites (GCs), formulated using alka-li-activated metakaolin and aluminum powder. The production method involves spray-coating carbon steel plates with fresh GCs, followed by a 28-day curing period at room temperature. Sub-sequently, fire performance and aging tests are conducted to evaluate fire resistance. The study investigates GC properties, including apparent density, bending strength, compression strength, thermal conductivity, porosity, and production cost. Morphological changes before and after fire and aging tests are analyzed using scanning electron microscopy (SEM). Results demonstrate GC foams' outstanding thermal insulation, providing up to 75 minutes of fire resistance with a 6 mm coating, reducing temperatures by 300 °C compared to uncoated steel. GCs exhibit a density of 670 kg/m³, thermal conductivity of 0.166 W/m·K, 68% porosity, and cost efficiency at 250 dollars per cubic meter. This study underscores the potential of foamed geopolymer coatings for effective and economical surface protection.

Not in the history of transmissible illnesses has there been an infection as strongly associated with acute cerebrovascular disease as the novel human coronavirus, SARS-CoV-2. While the risk of stroke has known associations with other viral infections, such as influenza and human immunodeficiency virus, the risk of ischemic and hemorrhagic stroke related to SARS-CoV-2 is unprecedented. Furthermore, the coronavirus disease 2019 (COVID-19) pandemic has so profoundly impacted psychosocial behaviors and modern medical care that we have witnessed shifts in epidemiology and have adapted our treatment practices to reduce transmission, address delayed diagnoses, and mitigate gaps in health care. In this narrative review, we summarize the history and impact of the COVID-19 pandemic on cerebrovascular disease, and lessons learned regarding the management of patients as we endure this period of human history.

In this study composite with alternate layers of 5056 and 1580 alloys was manufactured by wire arc additive manufacturing technology. It is shown that increased strength characteristics of composite material can be obtained due to deformation treatment by high-pressure torsion (HPT) technique. The microstructure and mechanical properties of the HPT-processed material in different structural states were investigated. The HPT-processed material exhibits high value of ultimate tensile strength (~ 770 MPa) but low ductility. Short-term annealing at 250 oС and additional deformation by HPT to 0.25 of revolution at room temperature resulted in a slight decrease in material’s strength to ~ 700 MPa but provided ductility ∼ 9%. Physical mechanisms to improve plasticity in correlation with microstructure evolution is discussed.

The use of additive manufacturing in fabricating composite components has been gaining traction in the past decade. However, some issues with mechanical perfor-mance still need to be resolved. The issue of material porosity remains a pertinent one that needs more understanding to be able to determine viable solutions. Different re-searchers have examined the subject of porosity issues in AM-fabricated CFRP compo-sites. However, more research to quantitatively determine the effects of fabrication temperatures at the micro-scale is still needed. This study employed micro CT scan analysis to quantitatively compare the effects of fabrication temperatures at 230°C, 250°C, 270°C, and 290°C for CF-PA and CF-ABS composites. This followed an SEM evaluation which was used to determine the effects of the temperatures on interlayer and intralayer porosity generation. The porosity volume was related to the mechanical properties results in which it was determined how deposition temperatures affect the porosity volumes. It was also determined that semicrystalline composites are generally more affected by fabrication temperatures than amorphous composites, with the rela-tionship between porosity and mechanical properties also established. The overall po-rosity volume from the interlayer and intralayer voids was also determined, with the interlayer voids found to play a more determinant role in influencing the mechanical properties.

The shape of the knee is a chain-like structure of an ellipsoid. This suggests that, in the latest study, in addition to rolling, there is slippage in the motion of the knee. This paper selects a mechanical braking model for cattle based on two mechanical structures in different directions at the joints. The experimental results show that the modified dynamical system has strong chaotic properties. This can be one of the basis for judging various health states.

To enhance the mechanical properties (i.e. strength and elongation) of the face-centered cubic (fcc) α-phase in the Au-Cu-Al system, this study focused on the introduction of the martensite phase (doubled B19 (DB19) crystal structure of Au2CuAl) via the manipulation of alloy compositions. Fundamental evaluations, such as microstructure observations, phase identifications, thermal analysis, tensile behavior examinations, and reflectance analysis have been conducted. The presence of fcc annealing twins was both observed in the optical microscope (OM) and the scanning electron microscope (SEM) images. Both the strength and elongation of the alloys were greatly promoted while the DB19 martensite phase was introduced into the alloys. Amongst all the prepared specimens, the 47Au41Cu12Al and the 44Au44Cu12Al alloys performed the optimized mechanical properties. The enhancement of strength and ductility in these 2 alloys was achieved while the stress plateau was observed during the tensile deformation. A plot of the ultimate tensile strength (UTS) against fracture strain was constructed to illustrate the effects of the introduction of the DB19 martensite phase on the mechanical properties of the alloys. Regardless of the manipulation of the alloy compositions and the introduction of the DB19 martensite phase, the reflectance stayed almost identical to pure Au.

During mechanical ventilation, a disparity between flow, pressure or volume demands of the patient and the assistance delivered by the mechanical ventilator often occurs. Asynchrony effect and ventilator performance are frequently studied from ICU datasets or using commercially available lung simulators and test lungs. This paper introduces an alternative approach of simulating and evaluating patient-ventilator interactions with high fidelity using the electro-mechanical lung simulator xPULM™ under selected conditions. The xPULM™ approximates respiratory activities of a patient during alternating phases of spontaneous breathing and apnoea intervals while connected to a mechanical ventilator. Focusing on different triggering events, volume assist-controlled (V/A-C) and pressure support ventilation (PSV) modes were chosen to test patient-ventilator interactions. In V/A-C mode a double-triggering was detected every third breathing cycle leading to an asynchrony index of 16.67%, being classified as severe. This asynchrony causes a major increase of Peak Inspiratory Pressure PIP = 12.80 ± 1.39 cmH2O and Peak Expiratory Flow PEF = -18.33 ± 1.13 L/min when compared to synchronous phases of the breathing simulation. Additionally, events of premature cycling were observed during PSV mode. In this mode, the peak delivered volume during simulated spontaneous breathing phases almost doubles compared to apnoea phases. The presented approach demonstrates the possibility of simulating and evaluating disparities in fundamental ventilation characteristics caused by double-triggering and premature cycling under V/A-C and PSV ventilation modes. Various dynamic clinical situations can be approximated and could help to identify undesired patient-ventilation interactions in the future. Rapidly manufactured ventilator systems could also be tested using this approach.

Objectives: There are limited data regarding the efficacy of methylprednisolone in patients with acute respiratory distress syndrome (ARDS) due to coronavirus disease 2019 (COVID-19) requiring invasive mechanical ventilation. We aimed to determine whether methylprednisolone increases the number of ventilator-free days (VFDs) among these patients. Design: Retrospective single-center study Setting: Intensive care unit Patients: All patients with ARDS due to confirmed SARS-CoV-2 infection and requiring invasive mechanical ventilation between 1 March and 29 May 2020 were included Interventions: None Measurements and Main Results: The primary outcome was ventilator-free days (VFDs) during the first 28 days, defined as being alive and free from mechanical ventilation. The primary outcome was analyzed with competing-risks regression based on Fine and Gray’s proportional subhazards model. Death before day 28 was considered to be the competing event. A total of 77 patients met the inclusion criteria. Thirty-two patients (41.6%) received methylprednisolone. The median dose was 1 mg.kg-1 (IQR: 1-1.3 mg.kg-1) and median duration of 5 days (IQR:5-7 days). Patients who received methylprednisolone had a mean 18.8 VFDs (95% CI, 16.6-20.9) during the first 28 days vs. 14.2 VFDs (95% CI, 12.6-16.7) in patients who did not receive methylprednisolone (difference, 4.61; 95% CI, 1.10-8.12; P = 0.001). In the multivariable competing-risks regression analysis and after adjusting for potential confounders (ventilator settings, prone position, organ failure support, severity of the disease, tocilizumab, and inflammatory markers), methylprednisolone was independently associated with a higher number of VFDs (subhazards ratio: 0.10, 95%CI: 0.02-0.45; p=0.003). Hospital mortality did not differ between the two groups (31.2% vs. 28.9%, p=0.82). Hospital length of stay was significantly shorter in the methylprednisolone group (24 days [IQR:15-41 days] vs. 37 days [IQR:23-52 days], p=0.046). The incidence of positive blood cultures was higher in patients who received methylprednisolone (37.5% vs. 17.8%, p=0.052). However, 91% of patients who received methylprednisolone also received tocilizumab. The number of days with hyperglycemia was similar in the two groups. Conclusions: Methylprednisolone was independently associated with increased VFDs and shortened hospital length of stay. The combination of methylprednisolone and tocilizumab was associated with a higher rate of positive blood cultures. Further trials are needed to evaluate the benefits and safety of methylprednisolone in moderate or severe COVID-19 ARDS.

We study the center of energy (CE) before and after the separation of superposed wave from a moving medium (MM). It is assumed that two out-of-phase mechanical transverse waves propagating from the opposite directions on a medium moving at non-relativistic speeds are superposed and the superposed portion (SP) is separated from the MM at that moment. We consider the CE of the SP before and after the separation from the MM. The location of CE (LCE) of the SP seems to be at the center of it at the moment of superposition. The SP rotates due to the separation from the MM since the velocity of each portion symmetric with respect to the center of the SP is equal in magnitude and opposite in direction. The magnitudes of velocities of the symmetric portions become different as soon as the SP begins to rotate with the separation from the MM. Then the energies of their symmetric portions are not the same, so the LCE of the SP is not at the center of it. As a result, the LCE of it looks different before and after the separation from the MM. We must find a solution to keep the LCE of the SP constant. We propose that two out-of-phase mechanical transverse waves (MTWs) propagating from the opposite directions on a MM originally have hidden difference in relativistic energy and it suddenly appears within the range observable in Newtonian mechanics when the SP starts rotating. This means that the point of view of hidden difference in relativistic energy is necessary to keep the LCE constant.

The objective of this study was to assess the ability of producing laminated edible films manufactured using the following proteins; gelatin (G), whey protein isolate (WPI), and polysaccharide; sodium alginate (SA), and to evaluate their physical properties. Additionally, films’ preparation employing these ingredients was optimized through the addition of corn oil (O), Overall, 8-types of laminated films (G-SA, G-WPI, SA-WPI, SA-G-WPI, GO-SAO, GO-WPIO, SAO-WPIO, SAO-GO-WPIO were developed in this study. The properties of the prepared films were characterized through the measurement of; tensile strength (TS), elongation at break point (EB), puncture resistance (PR), tear strength (TT), water vapour permeability (WVP) and oxygen permeability (OP). The microstructure of cross-sections of laminated films was investigated by scanning electron microscopy (SEM). Mechanical properties of films were dramatically enhanced through the addition of film layers. GO-SAO laminate showed the best barrier properties to water vapour (22.6 ± 4.04 g mm/kPa d m2) and oxygen (18.2 ± 8.70 cm3 mm/kPa d m2). SAO-GO-WPIO laminate film was the strongest of all laminated films tested, having the highest TS of 55.77 MPa, PR of 41.36 N and TT of 27.32 N. SA-G-WPI film possessed the highest elasticity with an EB value of 17.4%.

Foam concrete is a highly cellularized cementitious material that undergoes extensive plastic deformation when loaded to failure. Under compression, the foam structure gets progressively crushed at a steady stress stage such that a substantial amount of energy is dissipated. Understanding foam concrete crushing behavior is of special importance for its engineering applications such as energy absorber, but the current studies are insufficient to define material properties for design of field applications. This study characterizes the crushing strength and foam modulus of samples with penetration test and resonant frequency test, respectively. A four-phase crushing behavior is observed. The yield strength and plateau strength are identified to characterize the foam crushing. Using the experimental inputs, the modulus-strength constitutive equations are then established. These findings are useful for expanding the knowledge of normal concrete to studies on foam concrete, as well as design of applications.Foam concrete is a highly cellularized cementitious material that undergoes extensive plastic deformation when loaded to failure. Under compression, the foam structure gets progressively crushed at a steady stress stage such that a substantial amount of energy is dissipated. Understanding foam concrete crushing behavior is of special importance for its engineering applications such as energy absorber, but the current studies are insufficient to define material properties for design of field applications. This study characterizes the crushing strength and foam modulus of samples with penetration test and resonant frequency test, respectively. A four-phase crushing behavior is observed. The yield strength and plateau strength are identified to characterize the foam crushing. Using the experimental inputs, the modulus-strength constitutive equations are then established. These findings are useful for expanding the knowledge of normal concrete to studies on foam concrete, as well as design of applications.

The mechanical properties of the materials stored inside agricultural silos influence the loads generated inside them. The different silo calculation methodologies allow predicting these loads under static and dynamic conditions if the mechanical properties of the stored materials are known. It has been known for many years that these properties are highly dependent on the moisture content of the material. However, to date there are not many studies focused on its determination. The goal of this research is the determination of the angle of internal friction, apparent cohesion, dilatancy angle and apparent specific weight of maize subjected to different moisture contents. Direct shear and oedometer assay devices were used for this purpose. In addition, the maize samples used were moistened using a climatic chamber. Moisture contents applied to maize sample ranged from 9.3% to 17.4%. The results obtained for the angle of internal friction and apparent cohesion, as well as those obtained for the apparent specific weight, were similar to those reported in the literature. However, the values obtained for the dilatancy angle of maize as a function of moisture content could not be compared because nothing has been published so far. The values obtained for this parameter overlap with those published for this material under ambient conditions. In addition, no direct relationship between the values obtained for this parameter and the moisture content of the sample could be found. Finally, the apparent specific weight increased with increasing moisture content of the samples, which differed from that published in the literature. The values provided here can be used for the optimization of storage and handling structures for granular agricultural materials using numerical methods.

The loads generated inside agricultural silos under static and dynamic conditions depend on the mechanical properties of the materials stored inside them. The silo calculation methodologies are based on these mechanical properties. Although it is known that moisture content greatly influences the values reached by these mechanical properties, just few studies have been conducted to determine them. The present work determines the angle of internal friction, the apparent cohesion, the dilatancy angle and the apparent specific weight of wheat when subjected to different moisture contents. Direct shear and oedometer assay devices were used. In addition, a climatic chamber was used to moisten the wheat samples used in this work. The moisture content applied to the samples ranged from 7.5% to 15.5%. From the different assays carried out it could be observed that the values of the angle of internal friction and apparent cohesion obtained from direct shear assays, as well as those related to the apparent specific weight obtained from oedometer assays were like those found in the literature. The apparent specific weight increased as moisture content increased, reaching a peak value at a moisture content of 13.4%, followed by a drop at a moisture content of 15.5%. The values here provided can be used in silo load calculations involving numerical methods.

The physical and mechanical properties of rocks will change significantly after being subjected to high temperatures, which poses safety hazards to underground projects such as coal underground gasification. In order to investigate the effect of temperature on the macroscopic and microscopic properties of rocks, this paper has taken sandstone as the research object and conducted uniaxial compression tests on sandstone specimens at different temperatures (20-1000 ℃) and different heating rates (5-30 ℃/min) at 1200 ℃. At the same time, the acoustic emission (AE) test system was used to observe the acoustic emission characteristics of the rock damage process, and the microstructural changes after high temperature were analyzed with the help of a scanning electron microscope (SEM). The test results show that the effect of temperature on sandstone is mainly divided into three stages: Ⅰ (20-500 ℃) stage is the strengthening zone, the evaporation of water and the contraction of primary fissures, sandstone densification is enhanced. Specifically, the compressive strength and elastic modulus increase, the macroscopic damage mode is dominated by shear damage, and the fracture micro-morphology is mainly brittle fracture. Stage II (500-600°C) is the transition zone, 500°C is the threshold temperature for compressive strength and modulus of elasticity, and the damage mode changes from shear to cleavage damage, and the sandstone undergoes brittle-ductile transition in this temperature interval. Stage III is the physicochemical deterioration stage. The changes in physical and chemical properties make the sandstone compressive strength and modulus of elasticity continue to decline, the macroscopic damage mode is mainly dominated by cleavage damage, and the fracture microscopic morphology is more toughness fracture. The effect of different heating rates on the mechanical properties of sandstone was further studied, and it was found that the mechanical properties of the rock were more deteriorated under higher heating rates.

We overview recent findings achieved in the field of model-driven development of additively manufactured porous materials for development of a new generation of bioactive implants for orthopedic applications. Porous structures produced of biocompatible titanium alloys by selective laser melting can present a promising material to design scaffolds with regulated mechanical properties and with capacity to be loaded with pharmaceutical products. Adjusting pore geometry, one could control elastic modulus and strength/fatigue properties of the engineered structures to be compatible with bone tissues, thus preventing the stress shield effect when replacing a diseased bone fragment. Adsorption of medicals by internal spaces would make it possible to emit the antibiotic and anti-tumor agents into surrounding tissues. We critically analyze the recent advances in the field featuring model design approaches, virtual testing of the designed structures, capabilities of additive printing of porous structures, biomedical issues of the engineered scaffolds and so on. A special attention is paid to highlight the current troubles in the field and the ways of their solutions.

Microelectromechanical System (MEMS) vibrating gyroscope design considerations are always intriguing due to their microscale mechanical, electrical, and material behavior. MEMS vibrating ring gyroscopes have become important inertial sensors in inertial measurement units (IMU) for navigation and sensing applications. The design of a MEMS vibrating ring gyroscope incorporates an oscillating ring structure as a proof mass, reflecting unique design challenges and possibilities. This paper presents a comprehensive design analysis of the MEMS vibrating ring gyroscope from the mechanical, electrical, and damping perspectives. The mechanical design of the MEMS vibrating ring gyroscope investigates the various frame designs of the vibrating ring structure, as well as the various beam structures, including curved, rectangular, and semicircular beam structures, which are analyzed using mathematical models and finite element analysis (FEA) simulations that provide an in-depth analysis of the stiffness and deflection of the vibrating structures. The electrical designs of the MEMS vibrating ring gyroscope were analyzed using various electrode configurations, electrostatic actuation, and capacitive detection mechanisms, respectively. The design analysis of various forms of damping, including viscous, structural, thermoelastic, and anchor damping, has been discussed. The variety of design structures investigated for MEMS vibrating ring gyroscopes' mechanical, electrical, and damping performance.

Liquid crystal elastomers (LCEs) are shape morphing materials whose large and reversible shape transformation results from the coupling between the mobile anisotropic properties of liquid crystal (LC) units and the rubber elastic of polymer networks. Their shape changing behaviors under the stimuli are largely directed by LC orientations, and therefore various strategies have been developed to spatially modulate the LC alignments. But most of the methods suffer from complex fabrication technologies or intrinsic limitations in applicability. To address this issue, programmable complex shape changes in some types of LCEs, such as polysiloxane side-chain LCEs or thiol-acrylate main-chain LCEs, etc, have been achieved by using a mechanical alignment programming process coupled with two-step crosslinking. Here, we report a polysiloxane main-chain LCE with programmable 2D and 3D shape changing performances achieved by mechanically programming the polydomain LCE between the two crosslinking steps. The resulting LCEs exhibited reversible thermal induced shape transformation between the initial and programmed shapes due to the two-way memory between the first network structure and the second network structure. Our work would be potential for expanding the applications of LCE materials in actuators, soft robotics and smart structures where arbitrary and easily programmed shape morphings are needed.

Bonding agents (BA) are key compounding ingredients for the correct formulation of composite solid rocket propellants (CSRP). In particular, the addition of BA is essential to achieve suitable mechanical properties of CSRP in terms of adequate tensile strength and elongation at break. It is shown that the polarity of each conventional BA as well as new potential BA can be measured through the Reichardt’s ET(30) polarity scale. Using this criteria it was possible to find a substitute for MAPO (tris-(methylaziridinyl)-phosphine oxide), a conventional BA with the drawback of high toxicity and high reactivity, with TTPT (tris-(pyrrolidine)-phosphine oxide), a completely safe and effective BA. In this work, many other potential BA were evaluated through the Reichardt’s ET(30) polarity scale but only a selection of the potential BA were effectively tested in a standard CSRP. Particular interesting was the evaluation of TTPT vs MAPO showing the ability of the former BA to match the mechanical properties of the latter BA.

Films prepared from poly(3-hydroxybutyrate-co-4-hydroxybutyrate) copolymers produced by Aneurinibacillus sp. H1 using an automatic film applicator were homogeneous and had a defined thickness, which allowed a detailed study of physicochemical properties. Their properties were compared with a poly (3-hydroxybutyrate) homopolymer film prepared by the same procedure, which proved to be significantly more crystalline by DSC and XRD. Structural differences between samples had a major impact on their properties. With increasing 4-hydroxybutyrate content, the ductility and release rate of the model hydrophilic active ingredient increased significantly. Other observed properties, such as the release of the hydrophobic active substance, the contact angle with water and ethylene glycol, or the surface morphology and roughness, were also affected by the composition. The identified properties predetermine these copolymers for wide use in areas such as biomedicine or smart biodegradable packaging for food or cosmetics. The big advantage is the possibility of fine-tuning properties simply by changing the fermentation conditions.

A technique for fabrication of bacterial cellulose-based films with CeO₂ nanofiller has been developed. The structural and morphological characteristics of the materials have been studied, their thermal and mechanical properties in dry and swollen states having been determined. The preparation methodology makes it possible to obtain composites with a uniform distribution of nanoparticles. The catalytic effect of ceria regarding the thermal oxidative destruction of cellulose has been confirmed by TGA and DTA methods. An increase in CeO₂ content led to an increase in the elastic modulus (a 1.27-fold increase caused by the introduction of 5 wt.% of the nanofiller into the polymer) and strength of the films. This effect is explained by the formation of additional links between polymer macro-chains via the nanoparticles’ surface. The materials fabricated were characterised by a limited ability to swell in water. Swelling caused a 20- to 30-fold reduction in the stiffness of the material, the mechanical properties of the films in a swollen state remaining germane to their practical use. The application of the composite films in cell engineering as substrates for the stem cells’ proliferation has been studied. The increase in CeO₂ content in the films enhanced the proliferative activity of embryonic mouse stem cells. The cells cultured on the scaffold containing 5 wt.% of ceria demonstrated increased cell survival and migration activity. An analysis of gene expression confirmed improved cultivation conditions on CeO₂-containing scaffolds.

An adequate number of waste management facilities is the key element to meet circular economy goals. Using empirical data taken from official sources the research framework bases on an econometric model to compare the elasticity of cost on quantity of different alternatives such as waste-to-energy facilities, mechanical biological facilities and landfills impact on waste management cost. Results suggest that both waste-to-energy facilities (-0.278%) and landfills (-0.38%) concur to lower the cost while the higher the percentage of waste sent to mechanical biological treatment facilities, the higher the cost (0.788%). This figure deserves to be examined in more details as such facilities represent an intermediary step in the chain which efficiency depends on the industrial organization of the chain.

Virus diseases of strawberry present several complex problems. More than 25 viruses have been described in the genus Fragaria thus far. Here, we describe a novel rhabdovirus, tentatively named strawberry virus 1 (StrV-1), that infects F. ananassa and F. vesca plants. Genomic sequences of three distinct StrV-1 genotypes co-infecting a single F. ananassa host were obtained using combined Illumina and Ion Proton high-throughput sequencing. StrV-1 was transmitted to herbaceous plants via Aphis fabae and A. ruborum, further mechanically transmitted to Nicotiana occidentalis 37B and sub-transferred to N. benthamiana, N. benthamiana DCL2/4i, N. occidentalis 37B and Physalis floridana plants. Irregular chlorotic sectors on leaf blades and the multiplication of calyx leaves seem to be the diagnostic symptoms for StrV-1 on indexed F. vesca clones. StrV-1 was detected in asymptomatic grafted plants and in 49 out of 159 field strawberry samples via RT-PCR followed by Sanger sequencing. The bacilliform shape of the virions, which have a cytoplasm-limited distribution, their size, and phylogenetic relationships support the assignment of StrV-1 to a distinct species of the genus Cytorhabdovirus. Acyrthosiphon malvae, A. fabae and A. ruborum were shown to transmit StrV-1 under experimental conditions.

A multi-strand composite welding wire was applied to join high nitrogen austenitic stainless steel, and microstructures and mechanical properties were investigated. The electrical signals demonstrate that the welding process using a multi-strand composite welding wire is highly stable. The welded joints are composed of columnar austenite and dendritic ferrite and welded joints obtained under high heat input and cooling rate have a noticeable coarse-grained heat-affected zone and larger columnar austenite in weld seam. Compared with welded joints obtained under the high heat input and cooling rate, welded joints have the higher fractions of deformed grains, high angle grain boundaries, Schmid factor and the lower dislocation density under the low heat input and cooling rate, which indicate a lower tensile strength and higher yield strength. The rotated goss (G_RD) orientation of a thin plate and the cube (C) orientation of a thick plate are obvious after welding, but the S orientation at 65° sections of Euler’s space is weak. The δ-ferrite was studied based on the primary ferrite solidification mode. It is observed that low heat input and high cooing rate result in the increasing of δ-ferrite and high dislocation density was obtained in grain boundaries of δ-ferrite. M₂₃C₆ precipitates due to low cooling rate and heat input in weld seam and deteriorates the elongation of welded joints. The engineering stress-strain curves also show the low elongation and tensile strength of welded joints under low heat input and cooling rate, which is mainly caused by the high fraction of δ-ferrite and the precipitation of M₂₃C₆.

The design of biomaterial platforms able to release bioactive molecules is mandatory in tissue repair and regenerative medicine. In this context, electrospinning is a user-friendly, versatile and low-cost technique, able to process different kinds of materials in micro- and nano-fibers with a large surface area-to-volume ratio for an optimal release of gaseous signalling molecules. Recently, the antioxidant and anti-inflammatory properties of the endogenous gasotramsmitter hydrogen sulfide (H2S), as well as its ability to stimulate relevant biochemical processes on the growth of mesenchymal stem cells (MSC), have been investigated. Therefore, in this work, new poly(lactic) acid fibrous membranes (PFM), doped and functionalized with H2S slow-releasing donors extracted from garlic, were synthetized. These innovative H2S-releasing mats were characterized for their morphological, thermal, mechanical and biological properties. Their antimicrobial activity and effects on the in vitro human cardiac MSC growth, either in the presence or in the absence of oxidative stress, were here assessed. On the basis of the results here presented, these new H2S-releasing PFM could represent promising and low-cost scaffolds or patches for biomedical applications in tissue repair.

The subject of the conducted study was focused on the development of new type of technical blends reinforced with natural fillers. The study was divided into two parts, where in the firsts stage of the research unmodified POM was reinforced with different types of natural fillers: cellulose, wood flour and husk particles. In order to select the type of filler intended for further modification, the mechanical characteristics was assessed. The 20% wood flour (WF) filler system was selected as the reinforcement. The second stage of research involved the use of combination of polyoxymethylene POM and poly(lactic acid) PLA. POM/PLA blend (ratio 50/50 %) were modified with elastomeric compound (EBA) and chain extender as reactive compatibilized (CE). The microscopic analysis revealed that for POM/PLA system the filler-matrix interface is characterized by better wettability, which might suggest higher adhesion. The mechanical performance revealed that for POM/PLA-based composites the properties were very close to the results for POM-WF composites; however, there is still large difference in thermal resistance in favor of POM-based materials. The increase in thermomechanical properties for POM/PLA composites occurs after heat treatment. The increasing crystallinity of the PLA phase allows for an significant increase of the head deflection temperature (HDT), even above 125 °C.

Rebar cages form the skeletal framework of reinforced concrete structural members. They comprise longitudinal and transverse reinforcing bars, usually connected by tie wires. Past studies have identified tie-wire connections as the "weak links" in large, prefabricated rebar cages, leading to their failure during site handling and construction stages. Recent research has explored the use of mechanical U-bolt connectors to bolster stability and safety of rebar cages while reducing their vulnerability and risk of failure. This paper presents a comprehensive experimental and numerical investigation of a new type of mechanical connector, referred to as "Cage Clamp", to enhance rebar cage stability and safety. Component-level experimental tests are conducted to determine the force-displacement response of Cage Clamp connectors for crossbar connections in different degrees of freedom. The results highlight the remarkable strength and stiffness of Cage Clamp connectors, significantly outperforming traditional tie-wire connections. Furthermore, full-scale experimental tests are performed on a circular underground pile-shaft rebar cage with Cage Clamp connectors to assess its behavior under various site handling conditions. The data obtained from these experiments are used to construct and refine detailed 3D finite element models of the rebar cages, capable of capturing the complex behavior of rebar cages with Cage Clamp connectors. Using the numerical model, a sensitivity analysis is performed to assess the effect of the number of Cage Clamps on the deflection and stability of the rebar cage. The findings show that using cage clamps to connect pick-up rebar with lateral reinforcement at every 8 to 10 feet is sufficient to ensure the stability of the cage during typical site handling conditions. The results of this study serve as a basis for establishing analysis, design, fabrication, and handling guidelines for rebar cages, contributing to safe and efficient construction practices.

Contact inhibition (CI) represents a crucial tumor-suppressive mechanism responsible for controlling the unbridled growth of cells, thus preventing the formation of cancerous tissues. CI can be further categorized into two distinct yet interrelated components: CI of locomotion (CIL) and CI of proliferation (CIP). These two components of CI have historically been viewed as separate processes, but emerging research indicates that they share both distinctive and common pathways. Moreover, they exhibit intriguing intersections with mechanotransduction, a process that involves cells sensing and responding to mechanical forces. This review article describes the intricate interplay between mechanical forces and CI, shedding light on how these forces regulate CIL and CIP. Emphasis is placed on filamin A (FLNA)-mediated mechanotransduction, elucidating how FLNA senses mechanical forces and translates them into crucial biochemical signals that regulate cell locomotion and proliferation. In addition to FLNA, trans-acting factors (TAFs) emerge as sensitive players in both CI and the mechanotransduction process. This article presents methods for identifying these TAFs and profiling the associated changes in chromatin structure, offering valuable insights into CI and mechanotransduction regulation. Finally, it addresses unanswered research questions in these fields and delineates their possible future directions.

Background Acute right heart failure (RHF) is associated with high morbidity and mortality. Temporary mechanical circulatory support (tMCS) is now part of the advanced management strategy for refractory cardiogenic shock (CS). Among such support systems, VA-ECMO remains the fastest MCS system to set up. The ProtekDuo cannula can be used as a temporary and percutaneous right ventricular assist device (RVAD) in relay with VA-ECMO in the context of prolonged weaning. Case Summary This case report describes the clinical course of a 69-year-old patient who underwent elective aortic valve replacement surgery complicated by acute RHF due to iatrogenic ligation of the right coronary artery. VA-ECMO was initiated in the context of refractory cardiogenic shock. Faced with prolonged MCS weaning, due to lack of recovery of the right ventricle associated with the absence of any other therapeutic option, a percutaneous RVAD via a ProtekDuo cannula was implanted as a bridge to recovery. The ProtekDuo was gradually weaned while the patient began rehabilitation. The patient was transferred to the medical ward after 5 weeks in the ICU, stayed 5 months in an acute medical setting, went to a rehabilitation center afterward and returned home 6 months after the initial surgery without any neurological sequalae or organ failures. In total, she remained on MCS for 39 days (21 on VA-ECMO and 18 on ProtekDuo). Discussion In cases of refractory RHF, after stabilization and organ perfusion restoration under VA-ECMO, it is feasible to switch to a percutaneous RVAD, allowing early mobilization of patients during prolonged MCS weaning until the right ventricle adapts to new loading conditions.

Egg activation is a cellular transition of an arrested mature oocyte into a developing embryo through a coordinated series of events. Previous studies in Hymenoptera have indicated that mechanical pressure can induce egg activation. In this study, we developed the first egg activation protocol for the haplodiploid insect pest, Sirex noctilio (Hymenoptera: Siricidae), from two climatically different regions in South Africa. In addition, activated eggs were exposed to three treatments involving water, pine sawdust, and the fungal symbiont of S. noctilio, Amylostereum areolatum (Russulales: Amylostereaceae), to confirm the hypothesised prerequisite of the symbiotic fungus for egg development. A rearing protocol was developed for emerged first instar larvae using a modified Anoplophora glabripennis (Coleoptera: Cerambycidae) artificial diet. A significant difference between mean survival rates of activated eggs from the two different regions was observed. Amylostereum areolatum was shown to be unnecessary for egg survival and adversely affected egg eclosion. Maximum larval survival duration on the artificial diet was 92 days. The egg activation and rearing protocol developed in this study enables opportunities for research on the physiology, ecology, symbioses, and genetics of S. noctilio, which can be exploited for new genetic pest management strategies.

Neat polyimide films are known to be dense and rigid. They are therefore not suitable for use in membranes, sensors and sustainable energy storage applications. In this study a novel technique has been used to simulta-neously improve the rigidity, damping ability and impact resistance of polyimide membranes. It is demonstrated that dispersion of a small amount of polyaniline copolymer-modified clay of about 0.25-0.5 wt.% into the pol-yimide matrix, resulted in enhanced storage modulus while maintaining high damping ability and glass transition temperature, Tg. Novel polyimide/substituted polyaniline-copolymer-clay nanocomposite membranes containing poly(N-ethyl-aniline-co-aniline-2-sulfonic-acid-modified-clay (SPNEAC) was successfully prepared and in-corporated into polyimide matrix to form modified clay/polyimide nanocomposites. UV-Vis analysis of the nanocomposite films show that the optical transparency of the SPNEAC-PI nanocomposite membranes de-creased with increasing SPNEAC concentration due to the high UV-Vis absorption of SPNEAC. Transmittance of about 3 % was observed in the nanocomposite membrane containing 5wt.% modified clay at 500 nm wave-length, which is significantly lower than that for the neat PI membrane of about 36 %. The dispersion of SPNEAC containing high concentration of clay (≥ 40 wt.% clay), SPNEAC2 in polyimide matrix, resulted in attainment of a higher degree of imidization than was possible for the neat organoclay/polyimide nanocomposite. This behavior is believed to be due to the synergistic interaction between PI and polyaniline copolymer modified clay. The viscoelastic property of polyimide and the nanocomposite membranes was measured by using the dynamic mechanical spectroscopy, DMS. It was shown that the glass transition temperature, Tg of the nano-composites decreased, while the damping ability and impact energy increased with increasing weight fraction of fillers.

The purpose of the review is to provide new insight into the potential of surface modification of carbon fibers for enhancing the application of the carbon fibers many a fold. To this end a total of 429 papers on the subject of surface modication of carbon fibers by a variety of chemical and electrochemical methods published during the period from 2010-2022 have been reviewed. Astounding results of surface funcationalization of carbon fibers by a variety of state of the art methods resulting in the unconventional applications of the resulting modified carbon fibers are summarized in a nut-shell in schemes from 1-6 towards the end of the review. Surface modifica-tion induces functionality to carbon fibers (CFs). The vitality of CF surface modification reac-tions could only be compared to the life process of respiration that sustains the multi functional-ity of living cells. Applicability of CFs can be drastically enhanced in incomprehensible ways by surface modification. Upon surface modification, inert and non-reactive CF surface becomes chemically active and functional with utility in diverse fields, namely, health, energy, environ-ment, defense, catalysis, smart materials and many others. Surface modification methods can be broadly classified into chemical, electrochemical and physical methods. By these surface modi-fication methods, the inert FC surface becomes polar. Surface properties like roughness, wetta-bility and energy are enhanced. Modification processes like sizing, oxidation, amination, si-lanization, polymerization, nanoarchitecture induces multifunctionality on CF surface. Modi-fied CFs when used as reinforcing material in carbon fiber reinforced plastics (CFRPs), im-proved bonding at the interface with resin matrices is observed with enhanced and outstanding mechanical properties (flexural strength, flexural modulus, IFSS, ILSS, hardness, elastic modulus, bending strength and compression strength).

Ultra-large cold-water pipes (CWP) may present structural instability phenomenon under complex and variable operating conditions, and the current theoretical analysis rarely takes into account the influence of multiple key parameters at the same time, resulting in some errors between the prediction results and the actual deformation behavior of the pipe. Considering this issue, this paper establishes a computational analysis model of the mechanical performance of the CWP based on the Euler-Bernoulli beam theory, considering the effect of waves, the clump weight at the bottom, internal flow and sea current, and gives a time-dependent solution of the mechanical response of the pipe with the action of multiple key parameters using the differential quadrature method (DQM). Additionally, the correctness and validity of the theoretical model are well verified by comparing the numerical solution with the theoretical results. Finally, to study the effects of operating conditions on the mechanical response of the pipe, the effects of waves, the clump weight, internal flow and sea current on the lateral deflection and maximum bending moment of the pipeline are discussed based on numerical simulation and orthogonal experimental method. The results show that changing the wave strength and internal flow velocity has little effect on the lateral deflection of the CWP, and the clump weight at the bottom can effectively suppress the lateral deflection of the pipeline, but increasing the current velocity can significantly increase the lateral deflection of the pipeline, which can lead to the instability of the pipe. Nevertheless, the effects of waves, the clump weight, internal flow and sea current on the maximum bending moment of the pipeline are basically the same, all of them increase sharply at first, and then decrease gradually until they level off, and the differences in the effects are mainly reflected in the different locations of the pipe sections. This paper suggests the design guidance of CWP in aspect of dynamic response depending on the operating condition.

This review is devoted to present the history of CARDIOSIM© software simulator platform, which was developed in Italy to simulate the human cardiovascular and respiratory system. The first version of CARDIOSIM© was developed at the Institute of Biomedical Technologies of the National Research Council in Rome. The first platform version published in 1991 ran on PC with disk operating system (MS-DOS) and was developed using the Turbo Basic language. The last version runs on PC with Microsoft Windows 10 operating system; it is implemented in Visual Basic and C++ languages. The platform has a modular structure consisting of seven different general sections, which can be assembled to reproduce different pathophysiological conditions. The software simulator can reproduce the most important circulatory phenomena in terms of pressure and volume relationships. It represents the whole circulation using a lumped-parameter model and enables the simulation of different cardiovascular conditions according to Starling’s law of the heart and a modified time-varying elastance model. Different mechanical ventilatory and circulatory devices have been implemented in the platform including thoracic artificial lung, ECMO, IABP, pulsatile and continuous right and left ventricular assist devices, biventricular pacemaker and biventricular assist devices. CARDIOSIM© is used in clinical and educational environment.

Induction of jasmonate-mediated plant defense against insect herbivory is initiated by a combination of both, mechanical wounding and chemical factors. In order to study both effects independently on plant defense induction, SpitWorm, a computer-controlled device which mimics the damage pattern of feeding insect larvae on leaves and, in addition, can apply oral secretions (OS) or other solutions to the ‘biting site’ during ‘feeding’, was developed and evaluated. The amount of OS left by a Spodoptera littoralis larva during feeding on Phaseolus lunatus (lima bean) leaves was estimated by combining larval foregut volume, biting rate, and quantification of a fluorescent dye injected into the larvae’s foregut prior to feeding. For providing OS amounts by SpitWorm equivalent to larval feeding, dilution and delivery rate were optimized. The effectiveness of SpitWorm was tested by comparing volatile organic compounds (VOC) emissions of P. lunatus leaves treated with either SpitWorm, MecWorm or S. littoralis larvae. Identification and quantification of emitted VOCs revealed that SpitWorm induced a volatile bouquet that is qualitatively and quantitatively similar to herbivory. Additionally, RT-qPCR of four jasmonic acid responsive genes showed that SpitWorm, in contrast to MecWorm, induces the same regulation pattern as insect feeding. Thus, SpitWorm mimics insect herbivory almost identical to real larvae feeding.

Forces and mechanical energy are prevalent in living cells. This may be because forces and mechanical energy preceded chemical energy at life’s origins. Mechanical energy is more readily available in non-living systems than the various other forms of energy used by living systems. Two possible prebiotic environments that might have provided mechanical energy are hot pools that experience wet/dry cycles and mica sheets as they move, open and shut, as heat pumps or in response to water movements.

Background: Osteoclastic bone resorption in the compression zone of periodontal ligament (PDL) plays a role in orthodontic tooth movement, and is regulated by the balance of RANKL and OPG. Compression downregulates OPG, conversely, tension upregulates OPG in PDL cells. However, the regulatory mechanism of OPG expression in PDL cells under different mechanical stresses remains unclear. Methods: To study microRNA (miRNA) expression profiles, compression (2g/cm²) or tension (15%-elongation) was applied to immortalized human PDL (HPL) cells, and miRNA was extracted. The miRNA expression was analyzed using a human miRNA microarray, and the changes of the miRNA expression were confirmed by real-time RT-PCR. In addition, miR-3198-mimic and -inhibitor were transfected into HPL cells to understand the resulting OPG expression and production. Results: Certain miRNAs were expressed differentially under compression and tension. Some miRNAs including miR-3198 were upregulated only by compression. Real-time RT-PCR confirmed that compression induced miR-3198, but tension reduced it, in HPL cells. miR-3198-inhibitor upregulated and miR-3198-mimic reduced OPG in HPL cells. miR-3198-inhibitor rescued the compression-mediated downregulation of OPG. On the other hand, miR-3198-mimic reduced OPG expression under tension. Conclusion: We conclude that miR-3198 is upregulated by compression and is downregulated by tension, suggesting that miR-3198 downregulates OPG in response to mechanical stress.

In the paper, a study of the performance of unmanned ground vehicle (UGV), establishes numerical simulation model of the chassis system by three-dimensional software and finite element analysis software. Based on the numerical modelling and analysis, the work focuses on study of the strength and stiffness of the vehicle's chassis and researched the distribution of stress and deformation under the extremal condition. The paper also presents an autopilot design with new cascade control system for an autonomous motion of an unmanned ground vehicle based on Proportional-Integral-Derivative (PID) and Feed-Forward (FF) control. The PID-FF controller is a part of dedicated for presented UGV used in a hybrid control system for precise control and stabilization, necessary to increase the vehicle motion stability and maneuvers precision. The hybrid PID-FF control system proposed for the ground vehicle model gives a satisfactory quality of control, while maintaining the simplicity of the control system. Presented tests performed in area of mechanical design and control analysis gives good results and proves usefulness of designed unmanned device.

The manufacturing method influences the properties of the produced components. This work investigates the influence of manufacturing methods such as fused filament fabrication (3D printing) and injection molding on water absorption, mechanical and thermal properties of the specimens produced from neat biobased poly(lactic acid) (PLA) polymer and poly(lactic acid)/wood composites. Acrylonitrile butadiene styrene (ABS) acts as the reference material due to its low water absorption and good functional properties. The printing layer thickness is one of the factors that affects the properties of a 3D printed specimen. The investigation includes two different layer thicknesses (0.2 mm and 0.3 mm) while maintaining uniform overall thickness of the specimens across two manufacturing methods. 3D printed specimens absorb significantly higher amounts of water than the injection molded specimens, and the increase in the layer thickness of the 3D printed specimens contributes to further increased water absorption. However, the swelling due to water absorption in 3D printed specimens decreases on increased layer thickness. Tensile, flexural and impact properties of all the specimens decrease after water absorption while the properties improve on decreasing the layer thickness. Higher porosity on increasing the layer thickness is the predominant factor. The results from dynamic mechanical analysis and microscopy validate the outcomes.

The composite post insulator composed of a large diameter mandrel and flange pressed by one-time integral pultrusion has high strength and good toughness, widely used in the existing flexible converter valve. For constructing the finite element model of the crimped post insulator, most of the flange surface and the mandrel surface are directly connected, making the simulation model's stiffness deviate from the actual model and the model distortion. Based on this, this study proposes a new finite element simplified model of crimped composite post insulator based on Multi-Point Constraints (MPC), which accurately simulates the crimping area of man-drel and flange in engineering practice. It verifies the model's reliability through static tests and characteristic vibration tests. The results show that the difference between the finite element simulation and test results is within 5 %. The finite element modeling method based on MPC local constraints is very reliable in applying crimped composite post insulators. Based on the proposed model, the influence of flange height and thickness on the mechanical properties of composite post-insulators is further explored. The results show that the influence of flange height on mechanical properties can be ignored when the height of the insulator stiff-ener ( non-press common area ) is constant. Within the allowable thickness range of the flange crimping process, the increase in flange thickness will significantly reduce the maximum bend-ing stress of the insulator and increase its safety margin. It provides a good design idea for the design of crimping composite insulators.

Metal additive manufacturing technologies have large potential for future use in load bearing aerospace applications, requiring a deeper understanding of mechanical performance and influencing factors. The objective of this study is to manufacture fatigue specimens by laser powder bed fusion with comparable bulk and different as-built surface quality (without post-processing). This goal was pursued by using identical bulk/hatch scan parameters while varying contour scan parameters. The bulk quality was evaluated by density measurements according to Archimedes’ principle and tensile testing. The surfaces were investigated using the optical fringe projection method and surface quality was assessed by the areal surface texture parameters Sa (arithmetic mean height) and Sk (core height, derived from material ratio curve). The resulting mean values of max (ultimate tensile strength) were between 375 and 405 MPa, which is a variation of roughly 8%, for seven different surface conditions. It could be confirmed that the influence of contour scan variation on bulk quality is insignificant for the assessed samples.

Large power transformers are generally associated with a maximum capacity rating of 100 MVA or higher. These large liquid dielectric power transformers are a custom-built piece of equipment, thus very expensive, and a backbone element of the power grid. In extreme cases as, for example, severe geomagnetic disturbances, permanently monitoring their condition will enhance their electrical reliability and resilience to guarantee efficient management of its life cycle. However, some traditional monitoring/diagnosis techniques have singular features when applied to large power transformers and their interlinked subsystems. In this context, and since that information is hardly put in evidence and compiled in the literature, this paper reviews the particularities of monitoring and diagnosing those assets.

The sensitivity of macroscopic mechanical and thermal properties of grey cast iron is computationally investigated for a variety of graphite microstructures over a wide temperature range. In order to represent common graphite microstructures according to DIN EN ISO 945-1, a synthetic approach is used to algorithmically generate simulation domains. The developed mechanical and thermal model is applied in a large simulation study. The study includes statistical volume elements of the graphite microstructures classes GG-15 and IA2 to IA5, with 10 v.-%, 11 v.-% and 12 v.-% graphite, respectively, for a temperature range from 20 °C to 750 °C. Homogenized macroscopic quantities such as the Young's moduli, Poisson's ratios, yield strengths and thermal conductivities are predicted for the different microstructure classes by applying simulation and data analysis tools of the research data infrastructure Kadi4Mat.

The construction of molecular robotic-like objects that imitate living things is an important challenge for current chemists. Such molecular devices are expected to perform their duties robustly to carry out mechanical motion, process information, and make independent decisions. Dissipative self-organization plays an essential role in meeting these purposes. To produce a micro-robot that can perform the above tasks autonomously as a single entity, a function generator is required. Although many elegant review articles featuring chemical devices that mimic biological mechanical functions have been published recently, the dissipative structure, which is the minimum requirement, has not been sufficiently discussed. This article aims to show clearly that dissipative self-organization is a phenomenon involving autonomy, robustness, mechanical functions, and energy transformation. Moreover, the author details the recent experimental results of an autonomous light-driven molecular device that achieves all of these features. In addition, a chemical model of cell-amplification is also discussed to focus on the generation of hierarchical movement by dissipative self-organization. By reviewing this research, it may be perceived that mainstream approaches to synthetic chemistry have not always been appropriate. In summary, the author proposes that the integration of catalytic functions is a key issue for the creation of autonomous microarchitecture.

The interlaminar strength of mechanically interlocked polymer-metal-interfaces is strongly dependent on the surface structure of the metal component. Therefore, this contribution assesses the suitability of the fractal dimension for quantification of the surface structure as well as interlaminar strength prediction of aluminum/polyamide 6 polymer-metal-hybrids. Seven different surface structures, manufactured by blasting, combined blasting and etching, thermal spraying and laser ablation, are investigated. The experiments are carried out on a novel butt-bonded hollow cylinder testing method that allows shear and tensile strength determination with one specific specimen geometry. The fractal dimension of the metal surfaces is derived from cross-sectional images. For comparison, the surface roughness slope is determined and related to the interlaminar strength. Finally, a fracture analysis is conducted. For the investigated material combination, the experimental results indicate that the fractal dimension is an appropriate measure for predicting the interlaminar strength

Mechanical forces and mechanical energy are prevalent in living cells. This may be because mechanical forces and mechanical energy preceded chemical energy at life’s origins. Mechanical energy is more readily available in non-living systems than the various forms of chemical energy used by living systems. Two possible prebiotic environments that might have provided mechanical energy are hot pools that experience wet/dry cycles and mica sheets as they move, open and shut, as heat pumps or in response to water movements.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

Electro-mechanical braking(EMB) which represents development direction of autonomous and intelligent braking plays very useful role on enhancing the braking response performance and intelligence level for mine underground electric trackless rubber-tired vehicle (ETRV). However,there is no Electro-Mechanical Brake system applied practically in coal mine UTRV until now.The accurate control of braking clamping force can determine the length and precision of braking distance of mine ETRV.In addition,because of poor working conditions in underground coal mine tunnel ,braking clamping force sensor may be easy to occur failure,which may cause vital accident.Therefore,A cascaded three-closed-loop EMB system with a positive clamping force sensor or force estimator built for ETRV is established to achieve autonomous elimination and reset of braking clearance and reliable braking force tracking ability via utilizing the electro motor rotor angle displacement and hysteresis effect of mechanical components in this EMB.The results of simulation and experiment indicate that clamping force response is faster than traditional hydraulic disk braking system and proposed force estimator presents good fault-tolerant ability when sensor is fault.This EMB can replace the current hydraulic brake system to enhance automation level of braking control for ETRVs and braking force response performance, reduce oil pollution and cost of maintenance, which is also key technology support for really precise motion control of mine autonomous driving vehicles.

Silica aerogels and their derivatives have outstanding thermal properties with exceptional values in the thermal insulation industry. However, the brittle nature restricts its large-scale commercialization. Thus, enhancing their mechanical strength without affecting their thermal insulating properties is essential. Therefore, for the first time, highly thermally stable Poly(acrylamide-Co-acrylic acid) partial sodium salt is used as a reinforcing polymer to synthesize hybrid P(AAm-CO-AAc)-silica aerogels via epoxy ring-opening polymerization in the present study. Functional groups in P(AAm-CO-AAc) partial sodium salts, such as CONH2 and COOH, acted as nucleophiles for the epoxy ring-opening reaction with (3-glycidyloxypropyl)trimethoxysilane, which resulted in a seven-fold enhancement in mechanical strength compared to that of a pristine silica aerogel while maintaining the thermal conductivity at less than 30.6 mW/mK and porosity of more than 93.68%. Moreover, the hybrid P(AAm-CO-AAc)-silica aerogel demonstrated improved thermal stability up to 343 ⁰C owing to the synergetic effect between P(AAm-CO-AAc) and the silica aerogel, corresponding to thermal stability and strong covalent bonding among them. These excellent results illustrate that this new synthetic approach for producing hybrid P(AAm-CO-AAc)-silica aerogels is useful for enhancing the mechanical strength of a pristine silica aerogel without impairing its thermal insulating property and shows potential as an industrial heat insulation material.

To improve accessibility, this article describes a static, four-legged, walker that can be constructed from materials and fasteners commonly available from hardware stores coupled by open-source 3-D printed joints. The designs are described in detail, shared under an open-source license, and fabricated with a low-cost open-source desktop 3-D printer and hand tools. The resulting device is loaded to failure to determine the maximum load that the design can safely support in both vertical and horizontal failure modes. The experimental results showed the average vertical failure load capacity was 3680±694.3N, equivalent to 375.3±70.8kg of applied weight with the fractured location at the wood dowel handlebars. The average horizontal load capacity was 315.6±49.4N, equivalent to 32.2±5.1kg. The maximum weight capacity of a user of 187.1±29.3kg was obtained, which indicates the open-source walker design can withstand the weight requirements of all genders with a 95% confidence interval that includes a safety factor of 1.8 when considering the lowest deviation weight capacity. The design has a cost at the bottom of the range of commercial walkers and reduces the mass compared to a commercial walker by 0.5kg (19% reduction). It can be concluded that this open-source walker design can aid accessibility in low-resource settings.

Powder bed fusion (PBF) process is a metal additive manufacturing process which can build parts with any complexity from a wide range of metallic materials. PBF process research has predominantly focused on the impact of only a few parameters on product properties due to the lack of a systematic approach for optimizing a large set of process parameters simultaneously. The pivotal challenges regarding this process require a quantitative approach for mapping the material properties and process parameters onto the ultimate quality; this will then enable the optimization of those parameters. In this study, we propose a two-phase framework for optimizing the process parameters and developing a predictive model for 316L stainless steel material. We also discuss the correlation between process parameters -- i.e., laser specifications -- and mechanical properties and how to achieve parts with high density (> 98%) as well as better ultimate mechanical properties. In this paper, we introduce and test an innovative approach for developing AM predictive models, with a relatively low error percentage of 10.236% that are used to optimize process parameters in accordance with user or manufacturer requirements. These models use support vector regression, random forest regression, and neural network techniques. It is shown that the intelligent selection of process parameters using these models can achieve an optimized density of up to 99.31% with uniform microstructure, which improves hardness, impact strength, and other mechanical properties.

(1) Background: Benefits and timing of percutaneous dilatational tracheostomy (PDT) in Intensive Care Unit (ICU) COVID-19 patients are still controversial. PDT is considered a high risk procedure for transmission of SARS CoV-2 to health care workers (HCWs). The present study analyzed optimal timing of PDT, clinical outcomes of patients undergoing PDT and safety of HCWs performing PDT. (2) Methods: 133 COVID-19 patients underwent PDT in our ICU from April 1, 2020 to March 31, 2021, 23 patients were excluded and 110 patients were enrolled. A trained medical team was dedicated to the PDT procedure. Demographic, clinical history and outcome data were collected. Patients who underwent PDT were stratified into two groups: early group, PDT ≤ 12 days from orotracheal-intubation (OTI) and late group, >12 days from OTI; HCW surveillance program was performed. (3) Results: Early group included 57 patients and late group included 53 patients. Early group patients showed shorter ICU length of stay and fewer days of mechanical ventilation than the late group (p<0.001). At day 7 after tracheostomy, early group patients required fewer intravenous anesthetic drugs and experienced an improvement of ventilation parameters, PaO2/FiO2-Ratio, PEEP and FiO2 (p<0.001). No difference in case fatality ratio between the two groups was reported. No SARS-CoV-2 infection was reported in HCWs performing PDT. (4) Conclusions: PDT was safe and effective for COVID-19 patients, since it improved respiratory support parameters, reduced ICU length of stay and duration of mechanical ventilation, and optimized the weaning process. The procedure was safe for all HCWs involved in the dedicated medical team. The development of standardized early PDT protocols should be implemented and PDT procedure could be considered as first line approach in ICU COVID-19 requiring prolonged mechanical ventilation.

This work investigates how the user-controlled parameters of the 3D printing process define temperature conditions on the boundary between layers of the part being fabricated and how these conditions influence the structure and strength of the part. The process studied is fused filament fabrication with a desktop 3D printer and the material utilized is PLA (polylactic acid). As a characteristic of the part strength the fracture load in the case of a three-point bend and calculated related stress were used. During the printing process parts were oriented with the long side along the Z axis, thus, in the bend tests, the maximum stress occurred orthogonally to the layers. During the fabrication process, temperature distribution on the sample surface was monitored with thermal imager. Sample mesostructure was analyzed using SEM. The influence of the extrusion temperature, the intensity of part cooling, the printing speed and the time between printing individual layers were considered. The influence of all the parameters can be expressed through two generalizing factors: the temperature of the previous layer and the flow efficiency, determining the ratio of the amount of extruded plastic to the calculated. A regression model was proposed that describes the effect of the two factors on the printed part strength. Along with interlayer bonding strength, these two factors determine the formation of the part mesostructure (the geometry of the boundaries between individual threads). It is shown that the optimization of the process parameters responsible for temperature conditions makes it possible to approximate the strength of the interlayer cohesion to the bulk material strength.

The current paper is studying the influence of geometrical parameters of the FDM (FFF) 3D printing process on printed part strength for open source desktop 3D printers and the most popular material used for that purpose, i.e. PLA (polylactic acid). The study was conducted using a set of different nozzles (0.4, 0.6 and 0.8 mm) and a range of layer heights from the minimum to maximum physical limits of the machine. To assess print strength, a novel assessment method is proposed. A tubular sample is loaded in the weakest direction (across layers) in a three-point bending fixture. To explain the results obtained, a mesostructure evaluation through SEM scans of the samples were used. A significant influence of geometric process parameters was detected on sample mesostructure and, consequently, on sample strength.

Background: The goal of this study was to evaluate the effect of Extracorporeal Membrane Oxygenator (ECMO) on mortality in patients with cardiogenic shock excluding Impella and IABP use. Method: The large Nationwide Inpatient Sample (NIS) database was utilized to study any association between the use of ECMO in adults over age of 18 on mortality and complications with a diagnosis of cardiogenic shocks. Results: ICD-10 codes for ECMO, and cardiogenic shock for available years 2016-2020 were utilized. A total of 796,585 (age 66.5±14.4) patients had a diagnosis of cardiogenic shock excluding Impella. 13,160 (age 53.7±15.4) were treated with ECMO without IABP. Total inpatient mortality without any device was 32.7%. It was 47.9% with ECMO. Using multivariate analysis adjusting for 47 variables such as age, gender, race, lactic acidosis, three-vessel intervention, left main myocardial infarction, cardiomyopathy, systolic heart failure, acute ST-elevation myocardial infarction, peripheral vascular disease, chronic renal disease, etc., ECMO utilization remained highly associated with mortality (OR: 1.78, CI: 1.6-1.9, p<0.001). Evaluating teaching hospitals only revealed similar findings. Major complications were also high in ECMO cohort. Conclusion: In patients with cardiogenic shock, the use of ECMO was associated with the high in hospital mortality regardless of comorbid condition, high-risk futures, or type of hospital.

Vit-106 is a promising zirconium-based alloy with high glass-forming ability and belongs to the so-called bulk metallic glasses (BMG). Workpieces with a size of around one centimeter in all three dimensions can be obtained from a BMG alloy by casting. However, further increasing the cast size decreases the cooling rate and thus induces crystallization. Selective laser melting (SLM) is a well-known technique to overcome the size limitations for BMGs because a workpiece is built by the addition of multiple melt portions where the cooling rate is kept above the critical one. Currently, BMG parts obtained by SLM suffer from partial crystallization. The present work studies the influence of SLM process parameters on partial crystallization of Vit-106 by metallography and the influence of the microstructure on mechanical properties by microhardness and wear resistance testing. Submicron crystalline inclusions are observed in an amorphous matrix of Vit-106 alloy obtained by SLM. The size and the concentration of the inclusions can be controlled by varying the laser scanning speed. It is shown that submicron crystalline inclusions formed in the amorphous matrix during SLM can favorably affect microhardness and wear resistance.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

The article focuses on the galvanic replacement synthesis of Ti-Ni and Zr-Ni metal systems with the "core-shell" structure which are potential precursors for intermetallics. The authors defined the effective synthesis parameters and the formation features of polymetallic systems character-ized by granulometric, phase and elemental composition. The X-ray fluorescence and X-ray phase analysis methods showed that the deposition of nickel on dispersed titanium and zirconium leads to the production of test samples with phase composition representing a mechanical mixture of Ni and Ti, Ni and Zr. The method of X-ray fluorescence analysis showed that the presence of hy-drofluoric acid with a 0.5-1.5 M concentration results in the formation of fixed quantitative ratios of elements in the precipitate, which allows the quantitative composition of dispersed systems "titanium - nickel", "zirconium - nickel" to be regulated within a relatively wide range. Scanning electron microscopy proved that all synthesized systems are characterized by a highly porous structure that follows the titanium and zirconium particle surface contour and the presence of spherical nanoscale subunits on the formed particle surface.

While traditional AC mechanical circuit breakers have been competent for protecting AC circuits, high penetration of DC power distribution technologies like DC microgrids (MGs) obligate better disruption performance features such as quick and reliable switch-ing speeds. However, a DC circuit breaker (DCCB) novel design is challenging due to the need to quickly break high currents within milliseconds, caused by the high fault current rise in DC grids compared to AC grids. In DC grids, the circuit breaker must provide zero current crossing and be designed for absorbing surges since the arc is not naturally extinguished by the system. Additionally, the DC breaker must mitigate the magnetic energy stored in the system inductance and withstand residual over-voltages after current interruption. These challenges require a fundamentally different topology for DCCBs, which are typically made using solid-state semiconductor technology, metal oxide varistors (MOV), and ultra-fast switches. This study aims to provide a comprehensive review on development, design, and performance description of DCCBs in parallel with a specific concentration on analysis of internal topology, energy absorption path and sub-circuits in Solid-State (SS)-based DCCBs. The research explores various novel designs that introduce different structures for energy dissipation solution. The classification of these designs is based on the fundamental principles of surge mitigation and a detailed analysis of the techniques employed in DCCBs. In addition, our framework offers an advantageous reference point for the future evolution of SS-circuit breakers in numerous developing power delivery systems.