Tantalum oxide thin films are deposited by DC reactive magnetron sputtering from a tantalum metallic target and oxygen as reactive gas. The reactive gas pulsing process (RGPP) is implemented to produce TaOx compounds with tunable chemical compositions. The argon mass flow rate is maintained constant whereas that of the oxygen gas is pulsed during the deposition. A constant pulsing period T = 10 s is used and the introduction time of the oxygen gas, namely the tON injection time, is systematically changed from 0 to 100 % of the pulsing period T. As the tON injection time increases, the chemical composition of as-deposited TaOx films is continuously changed from pure metallic tantalum to the over-stoichiometric Ta2O5 material. Analysis of the crystallographic structure by X-ray diffraction shows that the films adopt the body-centered cubic structure (metallic Ta) for the lowest tON injection time values (oxygen stoichiometry x < 1.0) and become amorphous for the longest tON injection times. It is shown that the tON injection time is a key parameter to produce either homogeneous tantalum oxides, or periodic Ta/TaOx multilayers with alternations close to 3 nm. Similarly, optical transmittance spectra of the film/glass substrate system are recorded in the visible region and the electrical conductivity of the films is measured vs. temperature. Both exhibit a gradual evolution from metallic (300K = 8.17105 S m-1 with a null optical transmittance in the visible range) to semi-conducting (300K = 1.97103 S m-1 with a semi-transparent behavior) and finally to dielectric properties (300K < 10-5 S m-1 for interferential films) as a function of the oxygen concentration in the films.

Artemisia absinthium (A. absinthium) leaf extract was successfully used to create zinc oxide nanoparticles (ZnO NPs), and their properties were investigated via several techniques, including X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), Fourier transform infrared (FTIR), and UV–Vis spectroscopy. SEM analysis confirmed the spherical and elliptical shapes of the particles. Three different zinc peaks were observed via EDX at energies of 1, 8.7, and 9.8 keV, together with a single oxygen peak at 0.5 keV. XRD analysis identified ZnO NPs as having a hexagonal wurtzite structure with a particle size that decreased from 24.39 to 18.77 nm, and with an increasing surface area (BET) from 4.003 to 6.032 m2/g for the ZnO (without extract) and green ZnO NPs, respectively. FTIR analysis confirmed the groups of molecules that were accountable for stabilizing and minimizing the ZnO NPs, which was apparent at 3400 cm. Using UV–Vis spectroscopy, the band gap energies (Egs) for the green ZnO and ZnO (without extract) NPs were estimated, and the values were 2.65 and 2.79 eV, respectively.

The article continues the search for a general law that describes the physical properties of a solid body, represented as a complex compound, through the physical properties of its elements. For a set of mixtures of metal oxides (actinide oxides), their melting or solidification temperatures were described in terms of the atomic weighted sum of the melting/solidification temperatures of these metals and molecular oxygen, multiplied by a variable which depending on the crystal structure and properties of melt of the compound and on the atomic numbers of the elements that make up the compound.

Deposition/printing of materials with sub-1 μm precision and size (cross sections) is required for optical and electrical micro-devices. Crystalline c-ITO (Indium tin oxide) nanostructures were patterned on glass with a precision that formed gaps of 20-50 nm between individual disks or lines of ∼ 250 nm diameter or width. The absorbed energy density [J/cm3] followed the second order dependence on pulse energy. This facilitated high resolution and precision for nanoscale laser writing at the 515 nm laser wavelength. Patterns for optical elements such as circular gratings and micro-disks were laser printed using ITO as a resist. Unexposed amorphous a-ITO was chemically removed in aqueous 1% vol. HF solution. This use of a-ITO as solid-resist is promising for metamaterial and micro-optical applications.

An laboratory procedure has been developed to obtain lanthanum oxide from spent fluid catalytic cracking catalyst, commonly used in the cracking the heavy crude oil process. Two different spent fluid catalytic cracking catalysts, which are mainly formed by silica and alumina, and a certain amount of rare earths were leached under several conditions to recover the rare earth from the solids waste. Subsequently, liquid phases were subjected to a liquid-liquid extraction process, and lanthanum was quantitatively stripped using oxalic acid to obtain the corresponding lanthanum oxalates. After the corresponding thermal treatment, these solids were transformed into lanthanum oxide. Both, lanthanum oxalates and oxides solids have been characterized by wide techniques in order to investigate the purity of the phases.

Finnish government's carbon neutrality goal by 2035 requires integration of renewable energy sources into the power grid. Considering the stochasticity of these resources, additional sources of flexibility are necessary to balance supply and demand in the power grid. District heating network (DHN) operators in Finland plan to shut down fossil-fuel-based combined heat and power plants and electrify heating systems by deploying heat pumps (HPs) and electric boilers. Techno-economic analysis and optimal operation of DHN-connected HPs and electric boilers in providing ancillary balancing services considering the 15-minute granularity in the balancing markets in Finland were investigated. The objective was to maximize the potential revenue for DHN operators gained from the day-ahead electricity market and frequency containment reserve (FCR) balancing markets. Three inter-connected DHNs in the Helsinki metropolitan area were optimized considering the reference year 2019 and each operator's decarbonization strategies for 2025. HPs could gain the highest profit from FCR-D up-regulation market, while the electric boiler may gain considerable profits from FCR-D down-regulation market. Compared to other balancing markets studied, the FCR-N market had a limited profit margin. Sensitivity analysis indicated that spot electricity prices and CO2 emission allowance prices have a significant impact on the profit from balancing markets.

Bloodstream infection is a major health problem worldwide, with extremely high mortality. Detecting infection in the early stage is challenging due to the extremely low concentration of bacteria in the blood. Digital PCR provides unparalleled sensitivity and can achieve absolute quantification, but it is time-consuming. Moreover, the presence of unavoidable background signals in negative controls poses a significant challenge for single-molecule detection. Here, we propose a novel strategy called “Ultrafast flexible thin tube-based droplet digital PCR (utPCR)” that can shorten the digital PCR process from 2 hours to only 5 minutes, with primer annealing/extension time reduced from minutes to only 5 seconds. Importantly, the ultrafast PCR eliminates the nonspecific amplification and thus enables single-molecular detection. The utPCR enabled sensitive detection and digital quantification of E. coli O157 in the high background of 106-fold excess of E. coli K12 cells. Moreover, this method also displayed the potential to detect rare pathogens in blood samples, and the limit of detection (LOD) could be as low as 10 CFU per mL of blood without false positive results. Considering ultrafast (<5 min) and highly sensitive (single-molecule detection), the utPCR holds excellent prospects in the next generation of molecular diagnosis.

The rapid, sensitive, and selective detection of pathogenic bacteria is of utmost importance in ensuring food safety and preventing the spread of infectious diseases. Here, we present a novel, reusable, and cost-effective impedimetric sensor based on a dual bacteria-imprinted polymer (DBIP) for the specific detection of Escherichia coli O157:H7 and Staphylococcus aureus. The DBIP sensor stands out with its remarkably short fabrication time of just 20 minutes, achieved through the efficient electro-polymerization of o-phenylenediamine monomer in the presence of dual bacterial templates, followed by in-situ template removal. The key structural feature of the DBIP sensor lies in the cavity-free imprinting sites, indicative of a thin layer of bacterial surface imprinting. This facilitates rapid rebinding of the target bacteria within a mere 15 minutes, while the sensing interface regenerates in just 10 minutes, enhancing the sensor's overall efficiency. A notable advantage of the DBIP sensor is its exceptional selectivity, capable of distinguishing the target bacteria from closely related bacterial strains, including different serotypes. Moreover, the sensor exhibits high sensitivity, showcasing a low detection limit of approximately 9 CFU mL-1. The sensor's reusability further enhances its cost-effectiveness, reducing the need for frequent sensor replacements. The practicality of the DBIP sensor was demonstrated in the analysis of real apple juice samples, yielding good recoveries. The integration of quick fabrication, high selectivity, rapid response, sensitivity, and reusability makes the DBIP sensor a promising solution for monitoring pathogenic bacteria, playing a crucial role in ensuring food safety and safeguarding public health.

Herein, we developed a highly sensitive and specific bimolecular fluorescence complementation (BiFC)-based influenza A virus (IAV) sensing system created by combining a galactose/glucose-binding protein (GGBP) with an N-terminal large domain (YN1-172) and a C-terminal small domain (YC173-239) of enhanced yellow fluorescence protein (eYFP). The GGBP-based BiFC reporter exhibits the fluorescence reconstitution as a result of conformational changes in GGBP when lactose, derived from 6’-silalyllactose used as a substrate for neuraminidase (NA), binds to GGBP in the presence of IAV. The system showed a linear dynamic range from 1 x 100 TCID50/mL to 1 x 107 TCID50/mL, with a detection limit of 4 x 101 TCID50/mL for IAV (H1N1), demonstrating ultra-high sensitivity. Our system exhibited fluorescence intensity enhancements in the presence of IAV, while displaying weak fluorescence signals when exposed to NA-deficient viruses such as RSV A, RSV B, adenovirus and rhinovirus, thereby indicating selective responses for IAV detection. Taken together, our system provides a simple, highly sensitive and specific IAV detection platform based on BiFC capable of detecting the ligand-induced protein conformational changes, obviating the need for virus culture or RNA extraction processes.

Phenotypic plasticity in response to adverse conditions determines plant productivity and survival. The aim of this study was to test if two highly productive Populus genotypes, characterized by different in vitro etiolation patterns, differ also in their responses to hormones gibberellin (GA) and abscisic acid (ABA), and to a GA biosynthesis inhibitor paclobutrazol (PBZ). The experiments on shoot cultures of ‘Hybrida 275’ (abbr. H275; Populus maximowiczii × P. trichocarpa) and IBL 91/78 (Populus tremula × P. alba) were conducted either by modulating the physical in vitro environment or by adding specific chemicals to the nutrient medium. Our results show that there are significant differences between the studied genotypes in environmental and hormonal regulation of growth responses. The genotype H275, which responded to darkness with PBZ-inhibitable shoot elongation, was unable to recover its growth after treatment with ABA. In contrast, the genotype IBL 91/78, whose shoot elongation was not affected either by darkness or PBZ treatment, recovered so well after the ABA treatment that, when rooted subsequently, it developed longer shoots and roots than without ABA treatment. Our results indicate that GA catabolism and repressive signaling provide an important pathway to control growth and physiological adaptation in response to immediate or impending adverse conditions. These observations can help breeders define robust criteria for identifying genotypes with high resistance and productivity and highlight where genotypes exhibit susceptibility to stress.

Ecological and environmental damage caused by oil spillage has attracted great attention. Used cigarette filter (CF) has also caused negative environmental consequences. Converting CF to economical materials is a feasible way to address these problems. In this study, we demonstrate a simple method for production of a highly hydrophobic absorbent from CF. CF was modified by using different volume ratios of octadecyltrichlorosilane and methyltrimethoxysilane. When the volume ratio was 3:2, the modified CF had the high water contact angle of 155°. It could selectively and completely absorb silicone oil from an oil-water mixture and showed a good absorption capacity of 38.3 g/g. The absorbed oil was readily and rapidly recovered by simple mechanical squeezing, and it could be reused immediately without any additional treatments. The as-obtained superhydrophobic modified CF retained an absorption capacity of 80% for pump oil and 82% for silicone oil after 10 cycles. The modified CF showed good elasticity in the test of repeated use. The present study provides novel design of a functional material for development of hydrophobic absorbents from used CF via a facile method toward oil spillage cleanup as well as a new recycling method of CF to alleviate the environmental impact.

We explore the use of industrial sources of silicon and surfactant for obtaining low-cost MCM-41 materials and evaluate their performance as CO₂ adsorbents. All of them presented a high specific surface area with different structural characteristics and textural properties. The template was removed by using thermal treatments in an air atmosphere or a washing process. Preservation of silanol groups proved to be more effective under washing or mild thermal treatment conditions with the advantage of their lower cost and environmental benefit. Surface reactivity against CO₂ was enhanced by anchoring APTS to silanol groups through wet grafting. All amino-functionalized materials showed a performance as CO₂ adsorbents comparable to those reported in the literature. Samples with a higher concentration of silanol groups showed better performance. Our studies indicate that adsorbed CO₂ is retained at least up to 50°C, and the presence of aminopropyl groups is a key issue in CO₂ chemisorption on the MCM-41 surface. The chemisorbed gas at very low pressures points to the potential use of these materials for CO₂ storage.

In recent years web applications and on-line business transactions have grown many folds. Consequently, also cyberattacks have increased and represent a serious threat to the pervasive digital services upon which our society relies. To mitigate cyberattacks, many countermeasures are deployed on computing nodes (e.g., anti-malware software) as well as on network devices to detect and possibly block malicious packets in transit; these monitoring devices broadly go under the name of firewalls. Firewalls are designed according to two main architectural approaches: software running on a standard or embedded computer, or purposedly designed hardware, e.g., ASICs. Software-based solutions have the advantage of high flexibility and can be ported on easily upgradable hardware. However, hardware implementation represents the only viable solution for high data rates. On the market, very fast devices of the latter kind are available, but their cost is typically very high, especially considering that their ultra-optimized design makes updating them very difficult, with the consequence of a rather short lifespan. As a more balanced alternative, we wanted to investigate the use of an FPGA architecture, , which is significantly easier to update than custom-built chips, and features low-latency and high-throughput characteristics concurrently, making it preferrable to other programmable systems based on GPUs or microcontrollers. In this paper a packet sniffer that has been designed on FPGA with a 1 Gbit/s data transfer rate is presented. The system is implemented on the FPGA development board KC705 by Xilinx, can analyze Ethernet frames, checking the frame fields against a set of rules defined by the user and calculates statistics of the received Ethernet frames over time. The designed packet sniffer has been successfully tested both with Ethernet frames ad hoc generated using a packets generator, and with real web traffic by connecting the packet sniffer to the internet.

Building heterojunction is promising strategy for the achievement of highly efficient photocatalysis. In this study, a novel SnIn4S8@ZnO Z-scheme heterojunction with tight contact interface was successfully constructed through a facile two-step hydrothermal method. The phase composition, morphology, and photophysical properties of SnIn4S8@ZnO were studied through a series of characterization methods, respectively. Methylene blue (MB) was selected as the target pollutant for photocatalytic degradation and the degradation process was fitted with pseudo-first order kinetics. The as-prepared SnIn4S8@ZnO heterojunctions exhibited outstanding photocatalytic activities for the degradation of MB. The optimized sample (ZS800), in which the molar ratio of ZnO to SnIn4S8 was 800, displayed the highest photodegradation efficiency of MB (91%) within 20 min. Furthermore, the apparent rate constant of photodegradation for MB of ZS800 (0.121 min−1) was 2.2 times higher than that of pure ZnO (0.054 min−1). The improvement of photocatalytic activity could be attributed to the effective spatial separation of photogenerated charge carriers through a Z-scheme heterojunction with intimate contact interface. This work will provide a new insight into constructing excellent ZnO-based photocatalytic systems for wastewater purification.

This study explored the potential synergism within chlorhexidine-silver nanoparticles conjugates against Influenza type A, Staphylococcus aureus, Escherichia coli, and Candida albicans. Silver nanoparticles (SN) were obtained by the reduction of silver ions with green tea total phenolic extract and conjugated with chlorhexidine (Cx). The particles were characterized by UV-Vis and FTIR spectroscopies, dynamic light scattering, X-ray diffraction, and transmission electron microscopy. A stable negatively-charged nano-silver colloid (ζ=-50.01) was obtained with an average hydrodynamic diameter of 92.34 nm. In the presence of chlorhexidine, the spectral data and the shift of the zeta potential to positive values (ζ=+44.59) revealed the successful sorption of the drug onto the silver surface. The conjugates (SN-Cx) demonstrated potentiation in the effects against S. aureus and C. albicans, and synergism against E. coli with minimal inhibitory concentrations of SN 5.5 µg/mL+Cx 8.8 µg/mL. The SN showed excellent, increasing with time, virucidal properties, and low toxicity. The coupling of the cationic chlorhexidine with nano-silver, however, did not reduce its intrinsic cytotoxicity on various cell lines (MDCK, BJ, and А549). The newly-synthesized antimicrobial agent presented with an extended and promising therapeutic spectrum and needs to be further evaluated on relevant to the designated route of administration three-dimensional cell models (e.g., nasal, bronchial, dermal, ocular, etc.).

Maldivian coral reefs have been experiencing significant degradation due to a combination of global climate change and local anthropogenic pressures. To enforce the conservation of coral reefs worldwide, coral restoration is becoming a popular tool to restore ecosystems actively. In the Maldives, restoration interventions are performed only around touristic islands, where there are economic resources available to support these projects. Unfortunately, on local islands, coral restoration does not benefit from the same support and is rarely boosted. A challenging coral restoration intervention has been performed, for the first time, a on a local island of the Maldives affected by intense human pressures that caused the degradation of its reefs. A total of 242 coral fragments were collected from impacted colonies and transferred to the coral nursery of the island. Survival and growth rates of the fragments were monitored for 12 months. After one year, a survival rate of 70.2% was recorded. Although this rate might appear lower when compared to other restoration experiences, it is very promising considering the origin of the fragments and the poor quality of the environment where they have been transplanted. Some potential threats to the success of this restoration have also been identified, i.e., water temperature anomaly, diseases and parasites, the latter being the leading causes of coral mortality. The procedure presented here is comparatively less expensive than the typical relocation of entire coral colonies from donor healthy reefs to degraded reefs, thus providing an opportunity and a viable option also for local islands to restore their reefs and preserve local biodiversity.

Vegetation classifications on large geographic scales are necessary to inform conservation decisions and monitor keystone, invasive, and endangered species. These classifications are often effectively achieved by applying models to imaging spectroscopy, a type of remote sensing, data, but such undertakings are often limited in spatial extent. Here we provide accurate, high-resolution spatial data on the keystone species Metrosideros polymorpha, a highly polymorphic tree species distributed across bioclimatic zones and environmental gradients on Hawai'i island, using airborne imaging spectroscopy and LiDAR. We compare two tree species classification techniques, support vector machine (SVM) and spectral mixture analysis (SMA), to assess their ability to map M. polymorpha over 28,000 square kilometers where differences in topography, background vegetation, sun angle relative to the aircraft, and day of data collection, among others, challenge accurate classification. To capture spatial variability in model performance, we applied gaussian process classification (GPC) to estimate the spatial probability density of M. polymorpha occurrence using only training sample locations. We found that, while SVM and SMA models exhibit similar raw score accuracy over the test set (96.0% and 93.4%, respectively), SVM better reproduces the spatial distribution of M. polymorpha than SMA. We developed a final 2 m x 2 m M. polymorpha presence dataset and a 30 m x 30 m M. polymorpha density dataset using SVM classifications that have been made publicly available for use in conservation applications. Accurate, large-scale species classifications are achievable, but metrics for model performance assessments must account for spatial variation of model accuracy.

Current species’ range displacements are mostly triggered by climate change but European landscapes are largely dominated by human activities. In this study we identify the most promising spatial adaptive trajectories (SATs) for the thirty most threatened non volant mammal species in Europe up to 2080 (under three climate and land change scenarios) and where/when SATs of each species synchronically converge. We found large contrasts on the persistence of species in SATs, with some species largely reliant on the functionality of areas where many SATs converge. Overall, SATs and convergence centers are not adequately covered by existing conservation areas and coincide with crop and arable lands, compromising species persistence. It is important to invest in the protection of SATs and convergence centers through a mix of conventional instruments and new collaborative forms with the socio-economy. Anticipative plans at long-term coupled with risk analysis offer decision–makers templates to prevent negative surprises.

Nucleophilic aromatic substitution (SNAr) reactions can provide metal-free access to synthesize mono-substituted aromatic compounds. We have developed efficient SNAr conditions for p-selective substitution of polyfluoroarenes with phenothiazine in the presence of a mild base to afford the corresponding 10-phenylphenothiazine (PTH) derivatives. The resulting polyfluoroarene-bearing PTH derivatives were subjected to a second SNAr reaction to generate highly functionalized PTH derivatives with potential applicability as photocatalysts for the reduction of carbon–halogen bonds.

Flooding and overflows are recurring problems in several Brazilian cities, which usually undergo disorderly development. Their causes vary from increased impervious surface areas, deficiency/inefficiency of drainage structures and their maintenance, siltation of rivers, channel obstructions, and climatic factors. This situation is aggravated in the major cities. The Anhangabau watershed lies in the central portion of the city of Sao Paulo – Brazil and covers a drainage area of 5.4 km². The region is highly urbanized and crossed by a major north-south road connection. During heavy rain events, portions of this interconnection passage become compromised, disrupting the flow of vehicles, creating a chaotic situation for the population, as well as losses to the national economy. Observed rainfall records and an existing IDF (intensity duration frequency) curve for the region are used to obtain design storms. To account for climate change, a well know procedure, the equidistance quantile matching method for updating IDF curves under climate change, was applied to the existing historical data. Several different global climate models (GCM) and one regional model were applied to obtain and update rainfall design storm. The GCMs and future scenarios used were from the IPCC Assessment Report 5 (AR5) and two future projections: RCP (representative concentration pathway) 4.5 and 8.5. Alternatives previously proposed to solve to flooding issue are briefly reviewed. On one of the latest studies [1], a few modern concepts of water resources management are presented, and the linear retention measure was found to offer higher potential to mitigate the flooding problem in the lower valley of the watershed. Therefore, this alternative was used to evaluate different design storms scenarios combined with return periods of 25 and 100-years as well as the updated IDF under climate change for RCP 4.5 and RCP 8.5. To model the complex network, representing both road and drainage systems and their interconnections, PCSWMM/SWMM software was applied. Results are presented as flooding maps and show the impacts of the proposed linear retention measure based on the existing IDF curves and the updated IDF curves under climate change for two different drainage system conditions, current and improved with the use of linear retention reservoirs. Results show that the prosed changes on the drainage system help reduce the risk and damage to flooding. The climate change scenarios, however, impose a significant threat and need immediate attention from city planners and stakeholders.

Millions of people worldwide are affected by diabetes, a chronic disease that continuously grows due to abnormal glucose concentration levels present in the blood. Monitoring blood glucose concentrations is therefore an essential diabetes indicator to aid in the management of the disease. Enzymatic electrochemical glucose sensors presently account for the bulk of glucose sensors in the market. However, their disadvantages are that they are expensive and are dependent on environmental conditions, hence affecting their performance and sensitivity. To meet the increasing demand, non-enzymatic glucose sensors based on chemically modified electrodes for the direct electrocatalytic oxidation of glucose are a good alternative to the costly enzymatic-based sensors currently on the market, and the research thereof continues to grow. Nanotechnology-based biosensors have been explored for their electronic and mechanical properties, resulting in enhanced biological signalling through the direct oxidation of glucose. Copper oxide and copper sulfide exhibit attractive attributes for sensor application, due to their non-toxic nature, abundance, and their unique properties. Thus, in this review, copper oxide and copper sulfide-based materials, are evaluated based on their chemical structure, morphology, and fast electron mobility as suitable electrode materials for non-enzymatic glucose sensors. The review highlights the present challenges of non-enzymatic glucose sensors that have limited their deployment into the market.

Solid oxide cells are capable of efficiently converting various chemical energy carriers to electricity and vice versa. The urgent challenge nowadays is the faster degradation rate compared with other fuel cell/electrolyzer technologies. To understand the degradation mechanisms, simulation of a solid oxide cell is helpful. Since most previous research developed models using commercial software, such as COMSOL and ANSYS Fluent, a gap for knowledge transfer is being gradually formed between academia and industry due to licensing issues. This paper introduces a multiphysics model, developed by a computational code, openFuelCell2. The code is implemented with an open-source library, OpenFOAM. It accounts for momentum transfer, mass transfer, electrochemical reactions and metal interconnect oxidation. The model can precisely predict I-V curves under different temperatures, fuel humidity and operation modes. Comparison between OpenFOAM and COMSOL simulations shows good agreement. The metal interconnect oxidation is modelled, which can predict the thickness of the oxide scale under different protective coatings. Simulations are conducted by assuming an ultra-thin film resistance on the rib surface. It is revealed that coatings fabricated by atmospheric plasma spraying can efficiently prevent metal interconnect oxidation, with a contribution of only 0.53 \% to the total degradation rate.

The interaction between O2 and reduced ceria nanocubes was mainly investigated by FTIR spectroscopy. Nanorods and nanoparticles were also studied for comparison. Adsorption of O2 at 100 K on unreduced ceria produces only O2 molecularly adsorbed on Ce4+ sites. The Ce3+ cations in H2-reduced ceria were monitored by the 2F5/2 → 2F7/2 electronic transition band at 2133-2095 cm-1. This band possesses a fine structure well resolved at 100 K. The positions of the individual components depend on the Ce3+ environment, including the presence of nearby species such as OH groups. Even at 100 K, the interaction of O2 with reduced ceria leads to fast oxidation of about half of the Ce3+ cations, including all Ce3+ sites bound to OH groups and carbonates, and the simultaneous formation of superoxo (O2) and peroxo (O22) species. The remaining fraction of Ce3+ sites disappears upon heating up to 348 K. At higher temperatures, the peroxo species decompose directly, yielding lattice oxygen. Superoxides are converted to hydroperoxides, which then decompose to terminal OH groups. Reduced samples evacuated at T &lt; 773 K contain sorbed H2. Part of this hydrogen is also fast oxidized to H2O even at 100 K.

Despite the increasing role of machine learning in various fields, very few works considered artificial intelligence for frequency estimation (FE). This work presents a comprehensive analysis of deep-learning (DL) approach for frequency estimation of single-tones. It is shown that DL network with two layers having a few nodes can estimate frequency more accurately than well-known classical techniques. The study is comprehensive, filling gaps of existing works, where it analyzes error under different signal-to-noise ratios, numbers of nodes, and numbers of input samples; also, under missing SNR information. It is found that DL-based FE is not significantly affected by SNR bias or number of nodes. DL-based approach can work properly using minimal number of input nodes N at which classical methods fail. It is possible for DL to use as little as two layers with two or three nodes each, with complexity of O{N} versus O{Nlog2 (N)} for DFT-based FE, noting that less N is required for DL. Hence, DL can significantly reduce FE complexity, memory, cost, and power consumption, making DL-based FE attractive for resource-limited systems like some IoT sensor applications. Also, reduced complexity opens the door for hardware-efficient implementation using short word-length (SWL) or time-efficient software-defined radio (SDR) communications.

The COVID-19 pandemic caused by the virus SARS-CoV-2 has been the greatest global threat to human health in the last three years. The most widely used methodologies for the diagnosis of COVID-19 are quantitative reverse transcription polymerase chain reaction (RT-qPCR), used to detect the viral genome, and rapid antigen tests (RATs), also known as lateral flow tests, that employ specific antibodies to detect the viral spike protein. While PCR is considered the gold standard test in terms of specificity and sensitivity, it is time-consuming and requires specialized instrumentation operated by skilled personnel. In contrast, RATs can be used in-home or at point-of care but are less sensitive leading to a higher rate of false negative results. An alternative methodology for the detection of virus is the use of electrochemical biosensors that employ disposable strip electrodes to which binding of viral components elicits a change in electrical signal. Laser-scribed graphene (LSG) electrodes are attractive candidates for use as biosensors electrodes suitable for SARS-COV-2 detection due to their low-cost, patternability and ease of fabrication. In this work, we describe the development of a biosensor for COVID-19 detection that exploits a split-ester bond ligase system (termed ‘EsterLigase’) for immobilization of a virus-specific nanobody to maintain the out-of-plane orientation of the probe to ensure the efficacy of the probe-target recognition process. An anti-spike VHH E nanobody, genetically fused with the EsterLigase domain, was used as the specific probe for the spike receptor-binding domain (SP-RBD) protein as the target. The recognition between the two was measured by the change in the charge transfer resistance, determined by fitting the electrochemical impedance spectroscopy (EIS) spectra. The developed LSG-based biosensor achieved a linear detection range for the SP-RBD from 15 pM to 150 nM with a sensitivity of 0.0866 [log(M)]-1 and a limit of detection (LOD) of 7.68 pM.

The reflectance $R$ of monolayer graphene for the normal incidence of electromagnetic radiation is known to be remarkably defined only by $\pi$ and the fine-structure constant $\alpha$. It is shown in this paper that the reflectance (or the sum of transmittance and absorptance) of monolayer graphene, expressed as a quadratic equation with respect to the fine-structure constant $\alpha$ must unsurprisingly introduce the 2$^\text{nd}$ fine-structure constant $\alpha_2$, as the 2$^\text{nd}$ root of this equation, as well as two $\pi$-like constants for a convex and a saddle surface. It turns out that this 2$^\text{nd}$ fine-structure constant is negative, and the sum of its reciprocal with the reciprocal of the fine-structure constant $\alpha$ is independent of the reflectance value $R$ and remarkably equals $-\pi$. Particular algebraic definition of the fine-structure constant $\alpha^{-1} = 4\pi^3 + \pi^2 + \pi \approx 137.036$, containing the free $\pi$ term and agreeing with the physical definition of this dimensionless constant to the 5$^\text{th}$ significant digit, when introduced to this sum, yields $\alpha_2^{-1} = -4\pi^3 - \pi^2 - 2\pi \approx -140.178$. Assuming universal validity of the physical definition of $\alpha$, $\alpha_2$ defines the negative speed of light in vacuum $c_n$. The average of this speed $c_n$ and the speed of light in vacuum $c$ is in the range of the Fermi velocity ($10^6$ m/s). Furthermore, the 2$^\text{nd}$ negative fine-structure constant $\alpha_2$ alone introduces the imaginary set of base Planck units.

In order to obtain higher thermoelectric and mechanical properties in non-polar thermoplastic vulcanizates (TPVs), the Butyl rubber/Polypropylene (TPVs)/hydroxylated graphene (HGE) composites with nanosheet network were prepared through masterbatch technique and based on thermodynamic calculations, using polypropylene-graft-maleic anhydride (PP-MA) as a compatibilizer. The FTIR and Raman spectra revealed the introduced maleic anhydride group on PP-MA can form strong interfacial interaction with hydroxyl-containing functional groups on HGE. Morphology study indicated the rubber particles in the composites occupied the most volume of the PP phase, as expected to hinder the aggregation of HGE and form the effective nanosheet network. The nanosheet network can be combined with the IIR cross-linked particles during the dynamic vulcanization process to improve the interface bonding between PP and IIR, thus increasing the tensile strength of TPVs. When the content of HGE reached the percolation threshold (2 wt.%), the nanosheet network of HGE was formed, and the AC conductivity, dielectric permittivity and thermal conductivity increased sharply. The prepared TPVs/HGE nanocomposites have significantly improved in mechanical properties, thermal properties and dielectric properties, which provides a guarantee for their potential application as multifunctional TPVs polymers.

This study adapted and assessed a shortened version of the IAT (Internet Addiction Test) scale completed by young people aged 12 years and older regarding their online behaviors and risk of online addiction. The psychometric qualities of the reduced version - Screening IAT - youth are presented in order to validate its use in the early detection of online addiction. The total sample is composed of 3021 participants being 55.9% female and 44.1% male, with a mean age of x ̅=15 years (σ=3.028), attending junior high school (56.2%), high school (37.8%) and college (5.9%). The procedure included a factorial analysis, in which the total sample was randomly divided into three samples. An exploratory factor analysis was performed with one part of the sample, and a confirmatory factor analysis was performed with the others parts, assessing internal consistency, construct reliability, and discriminant validity. The results indicate that this reduced version of the IAT for young people has good psychometric qualities and can be applied in research and clinical settings. With this version and the parent-teacher version there is a direct contribution to a tripartite assessment of internet addiction risk.

Full-order state-space models represent the starting point for the development of advanced control methods for wind turbine systems (WTSs). Regarding existing control-oriented WTS models, two research gaps must be noted: (i) There exists no full-order WTS model in form of one overall ordinary differential equation that considers all dynamical effects which significantly influence the electrical power output; (ii) all existing reduced-order WTS models are subject to rather arbitrary simplifications and are not validated against a full-order model. Therefore, in this paper, two full-order nonlinear state-space models (of 11th and 9th-order in the (a, b, c)- and (d, q)-reference frame, resp.) for variable-speed variable-pitch permanent magnet synchronous generator WTSs are derived. The full-order models cover all relevant dynamical effects with significant impact on the system’s power output, including the switching behavior of the power electronic devices. Based on the full-order models, by a step-by-step model reduction procedure, two reduced-order WTS models are deduced: A non-switching (averaging) 7th-order WTS model and a non-switching 3rd-order WTS model. Comparative simulation results reveal that all models capture the dominant system dynamics properly. The full-order models allow for a detailed analysis covering the high frequency oscillations in the instantaneous power output due to the switching in the power converters. The reduced-order models provide a time-averaged instantaneous power output (which still correctly reflects the energy produced by the WTS) and come with a drastically reduced complexity making those models appropriate for large-scale power grid controller design.

This research review explores the synthesis of graphene quantum dots (GQDs) from biowaste for supercapacitor applications, driven by the need for sustainable and efficient energy storage technologies. GQDs, with their unique properties like high surface area and excellent conductivity, hold promise for enhancing supercapacitor performance. Various synthesis methods, including hydrothermal/solvothermal processes, chemical exfoliation, carbonization/pyrolysis, and microwave-assisted synthesis, are discussed alongside characterization techniques to evaluate GQD properties. Biowaste-derived GQDs demonstrate significant potential by improving specific capacitance and cycling stability in supercapacitor electrodes. Challenges such as scalability and material purity are identified, with future directions focusing on enhancing energy density, cycle life, and cost-effectiveness to propel the adoption of biowaste-derived GQDs in commercial energy storage applications.

Graphene quantum dots (GQDs) have garnered significant attention in recent years due to their unique properties and promising applications in various fields such as electronics, optoelectronics, bioimaging, and sensing. The synthesis of GQDs is a critical step in harnessing their potential, and numerous methods have been developed to produce GQDs with specific properties. This review provides an overview of the different techniques employed for synthesizing GQDs, including top-down and bottom-up approaches. Furthermore, it discusses the advantages, limitations, and potential applications of each method, offering insights into the future direction of GQD synthesis research.

This study is dedicated to enhancing lithium battery performance through the utilization of porous conductive polyaniline-modified graphene composites (PMGC). Given the growing importance of green energy, coupled with the development of lithium-ion battery systems and electric vehicles, achieving high-speed charge and discharge performance has become imperative. Traditional approaches involve incorporating additives like carbon nanotubes and graphene into electrodes to improve conductivity, but they encounter challenges related to cost and aggregation issues. In this study, polyaniline (PANI), a cost-effective, stable, and conductive polymer, was explored. PMGC was formed by employing ammonium persulfate (APS) as an oxidant during PANI polymerization, simultaneously serving as a surface modifier for graphene. The study systematically investigated the impact of varying amounts of PMGC on lithium-ion battery electrodes, assessing reductions in internal resistance, aging effects, different charge and discharge rates, and cycle performance. PMGC exhibited a porous structure formed by nanoscale PANI intertwining on graphene. Various measurements, including FT-IR, TGA, Raman spectroscopy, and battery performance assessments, confirmed the successful synthesis and positive effects of PMGC. Results indicated that a 0.5% addition of PMGC led to reduced internal resistance and enhanced fast charging and discharge capacity. However, excessive PMGC adversely affected aging and self-discharge. The study provides valuable insights into optimizing PMGC content for improved lithium battery performance, presenting potential advancements in energy storage systems and electric vehicles.

The application of dry lubrication in rolling contacts is challenging due to wear. In previous studies graphene platelets applied as dry lubricants on the surfaces of angular contact ball bearings demonstrated superior properties. These specific bearings, experiencing both rolling and spinning motion, create more severe conditions for dry lubricants. The applied graphene platelets have a thickness of few graphene layers in the nm range and a diameter in the µm range. Such platelets can be produced by mechanical exfoliation from graphite. To delve deeper into the lubrication effects, investigations were carried out using a milli tribometer. In the tests, a fixed steel ball is sliding against an oscillating counterpart under defined load. During the measurements, the applied load and tangential forces on the ball are recorded to calculate the friction. In our case, a steel ball with a diameter of 6 mm was used against graphene-based films on flat bearing surfaces (axial bearing washer). Comparative investigations included nano graphite particles and fullerene as dry lubricants, in addition to graphene platelets of various staple thicknesses. To increase the adhesion of the films to the surfaces, a pre-rolling process was implemented. Afterwards, the friction on the compressed films was measured. The results indicate that the pre-rolling process effectively reduces the friction of the system. After testing, the surfaces underwent analysis using laser scanning microscopy to assess the formed films, wear, and material transfer. It has been demonstrated that the pre-rolling process leads to the formation of a very thin compacted film with surface protective properties. On the ball as counterpart, the graphene platelets generate a transfer film on the contacting surface.

The first hyperpolarizability of graphene quantum dots (GQDs) suspended in water was determined using the hyper-Rayleigh scattering (HRS) technique. To the best of our knowledge, this is the first application of the HRS technique to characterize GQDs. Two commercial GQDs (Acqua-Cyan and Acqua-Green) with different compositions were studied. The HRS experiments were performed with an excitation laser at 1064 nm. The measured hyperpolarizabilities were (1.0±0.1) × 10^(-27) esu and (0.9±0.1) × 10^(-27) esu for Acqua-Cyan and Acqua-Green, respectively. The results were used to estimate the hyperpolarizability per nanosheet obtained by assuming that each GQDs has five nanosheets with 0.3 nm thickness. The two-level model, used to calculate the static hyperpolarizability per nanosheet, provides the values of (2.4±0.1) × 10^(-28) esu (Acqua-Cyan) and (0.5±0.1) × 10^(-28) esu (Aqua-Green). The origin of the nonlinearity is discussed on the basis of polarized resolved HRS experiments, and an electric quadrupolar behavior with a strong dependence on surface effects is found. The nontoxic characteristics and order of magnitude indicate that these GQDs may be useful for biological microscopy imaging.

Vertical graphene nanowalls (VGNWs) have emerged as a highly promising material in recent years due to their exceptional properties, such as a high specific surface area, excellent electrical conductivity, scalability, and compatibility with transition metal compounds. These attributes make VGNWs a compelling candidate for various applications, including energy storage, catalysis, and sensing, fostering great interest in their use in next future commercial graphene-based sensors like optoelectronic and plasmonic devices, energy storage electrodes, and catalytic systems. Among the diverse graphene synthesis methods, plasma-enhanced chemical vapor deposition (PECVD) has proven to be a robust technique for producing large-scale graphene films and creating VGNWs on diverse substrates. However, despite substantial progress in optimizing growth conditions to achieve micrometer-sized graphene nanowalls, the outcomes are often obtained through empirical approaches, and a comprehensive understanding of the underlying physicochemical mechanisms governing nanostructure formation remains elusive. In particular, a deeper exploration of atomic-level phenomena, such as nucleation, carbon precursor adsorption, and surface diffusion of adatoms, is imperative to exert precise control over the growth process. Concerning the synthesis of VGNWs, hydrogen plays a dual role in the graphene growth process, acting as both a co-catalyst and an etchant for the nanowalls. Nevertheless, a thorough comprehension of the intricate growth process is still required. To address these knowledge gaps, this review paper aims to investigate the nucleation and growth of VGNWs using PECVD, with a specific focus on exploring the temperature effect on the graphene growth ratio and nucleation density across a wide range of temperatures. By providing valuable insights into the PECVD process, our objective is to enable the optimization of growth conditions for tailoring VGNWs' properties, thereby facilitating their application in energy storage, catalysis, and sensing fields.

In recent years, graphene has received so much attention because of its superlative properties and its potential to revolutionize electronics especially in VLSI. This study analyzes the effect of single event upset (SEU) in SRAM cell which employs metal-oxide semiconductor type graphene nano-ribbon field effect transistor (MOS-GNRFET) and compares the results respectively with another SRAM cell designed in PTM 10nm FinFET node. Our simulation show there is a change in data stored in the SRAM after heavy ion strike. However, it recovers from radiation effects after 0.46 ns for GNRFET and 0.51 ns for FinFET. Since the degradation observed in Q and Qb of GNRFET SRAM are 2.7X and 2.16X as compared to PTM nano-MOSFET, we can conclude that GNRFET is less robust to single effect upset. In addition, the stability of SRAM can be improved by increasing the supply voltage VDD.

Since the discovery of graphene, due to its excellent optical, thermal, mechanical and electrical properties, it has a broad application prospect in energy, materials, biomedicine, electromagnetism and other fields. A great quantity of researches on the physical mechanism of graphene has been applied to engineering in electromagnetism and optics. To study the properties of graphene, different kinds of numerical methods have been developed for simulating the electromagnetic field effects of graphene, and equivalent boundary conditions have been employed to replace graphene in the computational domain. In this work, the numerical methods with equivalent boundary conditions are reviewed, and some examples are provided to illustrate their applicability.

In this paper, we have constructed a WKB approximation for graphene having a Y-shaped Kekul\'e lattice distortion and a special folding of the $\mbox{\boldmath$K$}$ and $\mbox{\boldmath$K$}^\prime$ valleys, which leads to very specific linear energy dispersions with two non-equivalent pairs of subbands. These obtained semi-classical results, which include the action, electron momentum and wave functions, are utilized to analyze the dynamics of electron tunneling through non-square potential barriers. In particular, we explore resonant scattering of an electron by a potential barrier built on Kekul\'e-distorted graphene. Mathematically, a group of consecutive equations for a semi-classical action have been solved by following a perturbation approach under the condition of small strain-induced coupling parameter $\Delta_0 \ll 1$ (a good fit to its actual value $\Delta_0 \backsim 0.1$). Specifically, we consider a generalized model for Kek-Y graphene with two arbitrary Fermi velocities. The dependence of the electron transmission amplitude on the potential profile $V(x)$ and band parameters of Kekul\'e-patterned graphene has been explored and analyzed in details.

In recent years graphene has attracted much interest due to its unique properties of flexibility, strong light-matter interaction, high carrier mobility and broadband absorption. In addition, graphene can be deposited on many substrates including silicon with which is able to form Schottky junctions opening the path to the realization of near-infrared silicon photodetectors based on the internal photoemission effect where graphene play the role of the metal. In this work, we review the very recent progress of the near-infrared photodetectors based on Schottky junctions involving graphene. This new family of device promises to overcome the limitations of the Schottky photodetectors based on metals showing the potentialities to compare favorably with germanium photodetectors currently employed in silicon photonics.

Mn3O4 /graphene nanosheets (GNS) composites serve as very excellent electrode materials for supercapacitors. They can fully combine the advantages of two materials such as graphene and metal oxide. Meanwhile, they can improve not only the specific energy and specific power of the materials, but also the cyclic stability of the materials. The results of the cyclic voltammetry and constant current charge discharge test on the composite electrode material have shown that the Mn3O4 /GNS powder sample has good capacitive performance. When the scanning rate is 5~50mV, the specific capacity retention rate of the composite electrode is 80.3% and 88% respectively. Mn3O4 nanoparticles, with the highest ratio of network coated GNS, exhibit a specific capacitance value of 957.6 F g−1 at a current density of 2 A g−1 in 1 M Na2SO4 solution. Besides, its network structure demonstrates high specific capacity and multiplying performance.

Biomaterials are the basis for the development of medicine because they allow safe contact with a living organism. The aim of this work was to produce innovative oxide layers with a porous microstructure on the surface of commercially pure titanium Grade 4 (CpTi G4), and to characterize their properties as drug carriers. Anodization of the CpTi G4 subjected to mechanical grinding and electrochemical polishing was carried out in a solution of 1M ethylene glycol with the addition of 40 g of ammonium fluoride at a voltage of 20 V for 2, 18, 24 and 48 hours at room temperature. It was found that the longer anodization time, the greater the number of pores formed on the CpTi G4 surface as revealed by FE-SEM method, and the greater the surface roughness determined in profilometric tests. As the anodizing time increases, the amount of the drug in the form of gentamicin sulfate incorporated into the resulting pores decreases. The most favorable drug release kinetics profile determined by UV-VIS absorption spectroscopy was found for the CpTi G4 anodized for 2 h making them the best choice when it comes to the drug carrier allowing full use of the therapeutic dose of the drug.

The influence of various energetic particles and electron injection on transport of minority carriers and non-equilibrium carrier recombination in Ga₂O₃ is summarized in this review. In Ga₂O₃ semiconductor, if robust p-type material and bipolar structures become available, diffusion length of minority carriers will be of critical significance. Diffusion length of minority carriers dictates functionality of such electronic devices as diodes, transistors, and detectors. One of the problems in ultra-wide band gap materials technology, is the short carrier diffusion length, due to scattering on extended defects. Electron injection in n- and p-type Gallium Oxide results in a significant increase of the diffusion length, even after its deterioration due to exposure to alpha- and proton-irradiation. Furthermore, post electron injection diffusion length in irradiated material exceeds that in Ga₂O₃ prior to irradiation and injection. The root cause of the electron injection-induced effect is attributed to the increase of minority carrier lifetime in the material due to trapping of non-equilibrium electrons on native point defects. It is, therefore, concluded that the electron injection is capable of “healing” the adverse impact of radiation in Ga₂O₃ and can be used for control of minority carrier transport and, therefore, device performance.

With metal oxide semiconductors being a promising candidate for accurate indoor air quality assessments, multiple drawbacks of the gas sensors prevent their widespread use. Examples include poor selectivity, instability over time, and sensor poisoning. Complex calibration methods and advanced operation modes can solve some of those drawbacks. However, this leads to long calibration times, which are unsuitable for mass production. In recent years, multiple attempts to solve calibration transfer have been made with the help of direct standardization, orthogonal signal correction, and many more methods. Besides those, a new promising approach is transfer learning from deep learning. This article will compare different calibration transfer methods, including direct standardization, piecewise direct standardization, transfer learning for deep learning models, and global model building. The machine learning methods to calibrate the initial models for calibration transfer are feature extraction, selection, and regression (established methods) and a custom convolutional neural network TCOCNN. It is shown that transfer learning can outperform the other calibration transfer methods regarding the root mean squared error, especially if the initial model is built with multiple sensors. It was possible to reduce the number of calibration samples by up to 99.3 % (from 10 days to approximately 2 hours) and still achieve an RMSE for acetone of around 18 ppb (15 ppb with extended individual calibration) if six different sensors were used for building the initial model. Furthermore, it was shown that the other calibration transfer methods (direct standardization and piecewise direct standardization) also work reasonably well for both machine learning approaches, primarily when multiple sensors are used for the initial model.

Background Nitrous Oxide (N₂O) is a dissociative anaesthetic that is sometimes used recreationally. The prevalence of N₂O use is difficult to quantify but appears to be increasing. Research on N₂O harms and application of harm reduction strategies are limited. The aim of this mixed method systematic review was to collate and synthesise the disparate body of research on recreational nitrous oxide use to inform harm reduction approaches tailored for young people. Methods To identify publications reporting recreational use of N₂O, a search of public health, psychology and social science databases was conducted. Databases included PubMed, CIHNAL, PsycINFO, Scopus and Web of Science. Gray literature and Google advanced search were also used. Due to limited published literature on the recreational use of N₂O, no limit was placed on publication date or study type. A thematic synthesis extracted descriptive and analytical themes from the selected studies. Quality appraisal was conducted using the CASP Tool for Qualitative studies and the Joanna Briggs Institute case report assessment tool Results The search retrieved 407 reports. Thirty-four were included in the final analysis including sixteen case reports. The included studies were primarily concerned with raising awareness of the apparently increasing use and subsequently increasing harms of recreational N₂O use. There was limited reference to policy or legislative responses in any published studies, no suggestions for harm reduction strategies or application of service level responses. In general, individuals lack awareness of N2O related harms. Conclusion The review found three key areas that deserve further consideration including: 1) policy, 2) service delivery, and 3) harm associated with N₂O use. We recommend a top-down (policy) and bottom-up (services delivery/services users) approach to harm reduction for N₂O use which also includes further consultation and research with both groups. Future research could explore young people’s experience of N₂O use including benefits and problems to inform contextually relevant harm reduction strategies.

Nitric oxide (NO) is a key molecule in cardiovascular homeostasis and its abnormal delivery is highly associated with the occurrence and development of cardiovascular disease (CVD). The assessment and manipulation of NO delivery is crucial to the diagnosis and therapy of CVD, such as endothelial dysfunction, atherosclerotic progression, pulmonary hypertension, and cardiovascular manifestations of Coronavirus (COVID-19). However, due to the low concentration and fast reaction characteristics of NO in cardiovascular system, the clinical applications centered on the NO delivery are challenging. In this tutorial review, we first summarized the methods to estimate the in vivo NO delivery process based on the clinical images and mathematical modeling to assess the endothelial function and vulnerability of atherosclerotic plaque. Then, the emerging bioimaging technologies that have the potential to directly measure the arterial NO concentration were discussed, including the Raman spectroscopy and electrochemical sensor. Aside from the diagnostic methods, therapies aimed at controlling NO delivery to regulate CVD were reviewed, including the inhaled NO therapy to treat the pulmonary hypertension and COVID-19, stem cell therapy and NO-releasing platform to treat endothelial dysfunction and atherosclerosis.

In this study, Mg-Al and Mg-Al-Ni - layered double hydroxides (LDHs) were successfully synthesized for efficient removal of Mn²⁺ from synthetically wastewater. LDH adsorbents (Mg-Al and Mg-Ni-Al) were prepared by co-precipitation method. The formation of the layered double hydroxide, the adsorption of manganese on both LDH (Mg-Al and Mg-Ni-Al) were observed by XRD, SEM and EDX analysis. The various parameters such as the effect of shaking time, initial Mn²⁺ concentration, temperature were controlled and optimized to removal of Mn²⁺ from synthetic wastewater. The kinetics and adsorption isotherms for Mn²⁺ removal from wastewater were studied in batch mode. At temperatures of 10 °C and 20 °C the adsorption equilibrium was reached after 24 h. Adsorption isotherms of Mn²⁺ are well fitted by Langmuir and Freundlich isotherm equation. The adsorption capacity of Mn²⁺ from synthetic wastewater of 80.607 mg/kg was obtained for (Mg-Al-Ni)-LDH. It is found that the adsorption kinetics is best described by the pseudo-second order model. These results prove that LDHs can be considered as a potential material for adsorption of Mn²⁺ from wastewater.

We report on the development of several different thin-film functional material systems prepared by RF magnetron sputtering at Edith Cowan University nanofabrication labs. We conduct research on the design, prototyping, and practical fabrication of high-performance magneto-optic (MO) materials, oxide based sensor components, and heat regulation coatings for advanced construction and solar windows.

Amorphous ferrite-type rare-earth (RE) substituted garnets and garnet-oxide nanocomposite layers are prepared on clear glass substrates by using RF magnetron sputter-deposition process. By using a combination approach employing custom-built spectrum-fitting software in conjunction with Swanepoel’s envelope method, the spectral dispersion function of optical constants and the layer thicknesses are derived accurately from the transmission spectra of the as-deposited samples. The effects of excess metal-oxides added to the base material systems during the co-deposition process are found to affect the refractive index and the optical absorption coefficients of garnet-oxide composites. A number of optical constant datasets are presented, enabling the experimentalists to design nanophotonic or integrated-optics devices employing these functional materials.

In 2021, amidst the COVID-19 pandemic and global food insecurity, the Nigerian poultry sector was yet exposed to highly pathogenic avian influenza (HPAI) virus and its economic challenges. Between 2021 and 2022, HPAI caused 467 outbreaks reported in 31 of the 37 administrative regions in Nigeria. In this study, we characterized the genome of 97 influenza A viruses of the subtypes H5N1, H5N2 and H5N8 identified in different agro-ecological zones and farms during the 2021-2022 epidemic. The phylogenetic analysis of the HA genes showed widespread distribution of the H5Nx clade 2.3.4.4b and similarity with the HPAI H5Nx viruses detected in Europe since late 2020. Topology of the phylogenetic trees indicates the occurrence of several independent introductions of the virus into the country followed by a regional evolution of the virus most probably linked to its persistent circulation in West African territories. An additional evidence of the evolutionary potential of HPAI viruses circulating in this region is the identification in this study of a putative H5N1/H9N2 reassortant virus in a mixed-species commercial poultry farm. Our data confirm Nigeria as a crucial hotspot for HPAI virus introduction from the Eurasian territories and reveal a dynamic pattern of avian influenza virus evolution within the Nigerian poultry population.

CD39 is involved in adenosine metabolism through conversion of extracellular ATP to adenosine. Because extracellular adenosine plays a critical role in the immune suppression of tumor microenvironment, the inhibition of CD39 activity by monoclonal antibodies (mAbs) is one of the important strategies for tumor therapy. In this study, we developed specific and sensitive mAbs for mouse CD39 (mCD39) using the Cell-Based Immunization and Screening (CBIS) method. The established anti-mCD39 mAbs, which were established by the CBIS method including C₃₉Mab-1 (rat IgG_2a, kappa) and C₃₉Mab-2 (rat IgG_2a, lambda), reacted with not only mCD39-overexpressed Chinese hamster ovary-K1 (CHO/mCD39) but also endogenously mCD39-expressed cell lines, such as L1210 (mouse lymphocytic leukemia) and J774-1 (mouse macrophage-like) cell lines through flow cytometry. Kinetic analyses using flow cytometry indicated that the dissociation constant (K_D) of C₃₉Mab-1 and C₃₉Mab-2 for CHO/mCD39 was 7.3 × 10⁻⁹ M and 5.5 × 10⁻⁹ M, respectively. K_D of C₃₉Mab-1 and C₃₉Mab-2 for L1210 was 3.3 × 10⁻⁹ M and 3.6 × 10⁻¹⁰ M, respectively. Furthermore, C₃₉Mab-1 could detect the lysate of CHO/mCD39 by western blot analysis. These results indicate that C₃₉Mab-1 and C₃₉Mab-2 are useful for the detection of mCD39 in many functional studies.

The bimodal grain-size distribution 0.9KNbO₃-0.1BaTiO₃ ceramics, with a typical perovskite structure in tetragonal phase at room temperature, were successfully prepared by an induced abnormal grain growth (IAGG) method at a relatively low sintering temperature. In this bimodal grain-sized distribution structure, the extra-large grains (about 10‒50 μm) were evolved from the micron-sized filler powders and the fine grains (about 0.05‒0.35 μm) were derived from the sol precursor matrix. The 0.9KNbO₃-0.1BaTiO₃ ceramics exhibit relaxor-like behavior with the diffused phase transition near room temperature, and confirmed by the existence of the polar nanodomain regions (PNRs) using the HRTEM images. The large room-temperature electrocaloric (EC) effect was found, characterized by an adiabatic temperature drop of 1.5 K, an isothermal entropy change of 2.48 J kg^-1 K^-1, and high EC strengths of ïDT/DEï = 1.50×10^-6 KmV^-1 and DS/DE = 2.48×10^-6 Jmkg^-1K^-1V^-1directly measured under E = 1.0 MV/m. These excellent ECEs demonstrate that this simple IAGG method is highly appreciated for synthesizing high-performance EC materials for efficient cooling devices.

Point defects induced by doping rare earth elements RE (Nd, Er) into the magnesium oxide host were investigated by classical atomistic simulations utilising the General Utility Lattice Program (GULP). Formation and association energies were calculated for the potential defect structures. Both isolated defects and defect complexes were considered. The most energetically favourable structures of defect complexes were found for rare earth doped and Li co-doped systems. The correlation between the association energy and the structure of the defect complex was investigated. The influences of Li were revealed with respect to energy and structure. The simulation results contribute to the understanding of the point defects of doped MgO and how Li influences the doping of rare earth elements in the MgO host.

Oxide additive-free α- ⇀ β-Si3N4 phase transformation of a high-purity commercial α-Si3N4 powder was investigated at 1600 to 1900 ℃ under nitrogen pressure of 980 kPa. The XRD analysis revealed that the α- ⇀ β-Si3N4 phase transformation proceeded mainly at 1900 ℃, and was completed by the extensive 1900 ℃-heat treatment for 20 h. This phase transformation temperature was 33 ℃ lower than the theoretical α-Si3N4 dissociation temperature and confirmed as completely different from that often discussed for the liquid phase sintering of α-Si3N4 powder by direct comparison with the phase transformation behavior of a reference powder, α-Si3N4 powder doped with 1 mol% Y2O3. The unique α- ⇀ β-Si3N4 phase transformation was further studied by a set of characterization techniques including elemental analysis, HAADF-STEM and STEM-EDS analyses. The results strongly suggested that the oxide additive-free α- ⇀ β-Si3N4 phase transformation was governed by the for-mation of metastable solid solution between α-Si3N4 and impurity oxygen of approximately 0.6 wt%, which promoted the dissociation below the theoretical α-Si3N4 dissociation temperature to afford thermodynamically favorable β-Si3N4. Along with the β-Si3N4 formation, the impurity oxygen was concentrated at the Si3N4 crystal grain boundaries and subsequently released from the sample via the grain boundary diffusion.

Copper oxide nanoparticles (CuONPs) were synthesized using an eco-friendly method and their antimicrobial and biocompatibility properties were determined. The supernatant and extract of the fungus Ganoderma sessile yielded small, quasi-spherical NPs with an average size of 4.5 ± 1.9 nm and 5.2 ± 2.1 nm, respectively. CuONPs showed antimicrobial activity against Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa. Minimum inhibitory concentration (MIC) for E. coli and S. aureus was 15.9 µg/mL for nanoparticles (NPs) using the supernatant (CuONPs-S) and 16.5 µg/ml for NPs using the extract (CuONPs-E). Lower concentrations were required for P. aeruginosa inhibition. Ultrastructural analysis revealed the presence of the small CuONPs all through the bacterial cells. Finally, the toxicity of CuONPs was analyzed in three mammalian cell lines: hepatocytes (AML-12), macrophages (RAW 264.7) and kidney (MDCK). Low concentrations (<15 µg/ml) of CuONPs-E were non-toxic to kidney cells and macrophages, and the hepatocytes were the most susceptible to CuONPs-S. The results obtained suggest that the CuONPs synthesized using the extract of the fungus G. sessile, could be further evaluated for the treatment of superficial infectious diseases.

Photocatalytic technology based on specific band structure of semiconductors offers a promising way to solve the urgent energy and environmental issues in modern society. In particular, hydrogen production from water splitting over semiconductor photocatalysts attracts great attention owing to the clean source and application of energy, which highly depends on the performance of photocatalysts. Among the various photocatalysts, TiO2 has been intensively investigated and used extensively due to its outstanding photocatalytic activity, high chemical stability, non-toxicity and low cost. However, pure TiO2 has a wide band gap of approximately 3.2 eV, which limits its photocatalytic activity for water splitting to generate hydrogen only under ultraviolet light, excluding most of the inexhaustible sunlight for human beings. Fortunately, the band gap of semiconductors can be manipulated, in which introducing oxygen defects is one of the most effective measures to narrow the band gap of titanium oxides. This review starts out by the fundamentals of photocatalytic water splitting for hydrogen production over TiO2, discusses the latest progress in this field, and summarizes the various methods and strategies to induce oxygen defects in TiO2 crystals. Then, the next section outlines the modification approaches of oxygen-deficient titanium oxide (TiO2-δ) to further improve its photocatalytic performance. Finally, a brief summary and outlook of the researches on TiO2-δ photocatalysts for water splitting to produce hydrogen were presented.

Magnetic nanoparticles based on iron oxides (MNPs-Fe) with magnetite or maghemite phases have been widely employed in bio-applications. Thus, they have been used as contrast agents in magnetic resonance imaging (MRI) and oncological treatments through different therapies. Besides, due to the vast health problem of multidrug-resistant bacterial infections, several studies have proposed MNPs-Fe as photothermal agents (PTAs) within antibacterial photothermal therapy (PTT). This work presents a quick and easy green synthesis (GS) to obtain MNPs-Fe using orange peel extract from orange waste from local commerce, which presents an environmentally friendly approach compared to traditional methods such as coprecipitation. The GS can be irradiated with microwaves to reduce the synthesis time drastically. We evaluated the weight yield of the GS and the physical-chemical and magnetic features of the synthesized MNPs-Fe. Besides their cytotoxicity in animal cell line ATCC RAW 264.7, their antibacterial activity against Staphylococcus Aureus (S. Aureus) and Escherichia Coli (E. Coli) was assessed. We found that the MNPs-Fe synthesized using the GS, with 50% v/v of NH4OH and 50% v/v of orange peel extract (50GS-MNPs-Fe) had an excellent weight yield, negligible cytotoxicity for concentrations of MNPs-Fe below 250 µg·mL-1 in 24 hours, and 8 days. In the MNPs-Fe surface, we identified a coating of organic molecules (~ 25 nm) such as terpenes, aldehydes, etc. MNPs-Fe inhibited S. Aureus and 2.54 log10 (CFU) of E. Coli under red LED light irradiation (630 nm, 65.5 mW·cm-2, 30 min). Likewise, they exhibited a superparamagnetic (SPM) behavior for temperatures above 60 K, with a size of 49.3±9.6 nm and saturation magnetization (Ms) of 72.83 and 44.16 emu·g-1 at 60 and 300 K, respectively. Therefore, 50GS-MNPs-Fe are excellent candidates as broad-spectrum PTAs in antibacterial PTT, magnetic hyperthermia (MH), or MRI.

The color of a thin copper oxide layer formed on a copper plate was transformed from reddish-brown into blue-purple by irradiation with 5 keV Ar+ ions to a fluence as low as 1 1015 Ar+ cm–2. In the unirradiated copper oxide layer, the copper valence state of Cu2+ as well as Cu+ and/or Cu0 was included as indicated by the presence of a shake-up satellite line in a photoemission spectrum. While for the irradiated one, the satellite line decreased in intensity, indicating that irradiation resulted in the reduction from Cu2+ to Cu+ and/or Cu0. Furthermore, nuclear reaction analysis using a 16O(d, p)17O reaction with 0.85 MeV deuterons revealed a significant loss of oxygen (51015 O atoms cm–2) in the irradiated layer. Thus, the chromatic change observed in the present work originated in the irradiation-induced reduction of a copper oxide.

We prepared heterogeneous alumina-silicate glasses by consolidating nanoparticles using molecular dynamics simulations. Consolidated glasses from either low alumina content alumina-silicate glasses or high alumina content alumina-silicate glasses show significantly improved ductility around consolidation pressure of ~3 GPa. The introduced structural heterogeneities, namely over-coordinated network formers and their neighboring oxygen atoms, are identified as plasticity carriers due to their high rearrangement propensity. In addition, consolidated oxide glass from both 23.4Al₂O₃76.6SiO₂ and 73.1Al₂O₃26.9SiO₂ nanoparticles show improved flow strength (up to 1 GPa) due to the introduction of chemical heterogeneities. Last but not least, apparent hardening behavior appears upon cold work in consolidated glasses, with an increase of yield strength from ~3.3 GPa to ~6.4 GPa. This method is a big advancement toward ultra-strong and ultra-tough glasses by breaking the structure, composition and size limitations in traditional melt-quench process.

In-situ grown C_0.3N_0.7Ti and SiC, which derived from non-oxide additives Ti₃SiC₂, are proposed to densify silicon nitride (Si₃N₄) ceramics with enhanced mechanical performance. Remarkable increase of density from 79.20% to 95.48% could be achieved for Si₃N₄ ceramics with 5vol% Ti₃SiC₂. The capillarity of decomposed Si from Ti₃SiC₂, and in-situ reaction between nonstoichiometric TiC_x and Si₃N₄ were believed to be responsible for densification of Si₃N₄ ceramics. An obvious enhancement of flexural strength and fracture toughness for Ti₃SiC₂ doped Si₃N₄ ceramics was observed. The maximum flexural strength of 795 MPa for Si₃N₄ composites with 5vol% Ti₃SiC₂ and maximum fracture toughness of 6.97 MPa^.m^1/2 for Si₃N₄ composites with 20vol% Ti₃SiC₂ are achieved when mixed powders are hot-press sintered at 1700℃. Pull out of elongated Si₃N₄ grains, crack bridging, crack branching and crack deflection were demonstrated to dominate enhance fracture toughness of Si₃N₄ composites.

An asymmetric [3+2] cycloaddition of azomethine ylides generated from the corresponding imino esters to trans-β-nitrostyrene catalyzed by chiral aziridine-containing phosphines and phosphine oxides is described. Of the sixteen stereoisomers that could be formed as a result of the title reac-tion, three were formed, two of which were obtained in an enantiomerically enriched or pure form, and one in a racemic form. One of the products underwent epimerization under basic reaction conditions.

PVC-based materials are bad in terms of biodegradability. To enhance the ecological property of such materials, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were obtained and study their optical, structural, thermal, and mechanical properties depending on the nature of the filler (spruce flour, birch flour, and rice husk) were studied. Increasing the proportion of plant filler somewhat reduces the strength characteristics and reduces the flexibility of the samples. But samples with plant filler allows them to be used at low temperatures without changing the operating characteristics. Some of the fillers affected the thermal stability of composites by increasing their thermal decomposition resistance. So, results have shown that plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compound for some applications such as construction.

Spiking neural networks (SNNs) promise to perform tasks currently done by classical artificial neural networks (ANNs) faster, in smaller footprints and using less energy. Neuromorphic processors are set out to revolutionize computing at a large scale, but the move to edge-computing applications calls for finely-tuned custom implementations to keep pushing towards more efficient systems. To that end, we have examined the architectural design space for executing spiking neuron models on FPGA platforms, focusing on achieving ultra-low area and power consumption. This work presents an efficient clock-driven spiking neuron architecture used for the implementation of both fully-connected cores and 2D convolutional cores, which rely on deep pipelines for synaptic processing and distributed memory for weight and neuron states. With them, we have developed an accelerator for an SNN version of the LeNet-5 network trained on the MNIST dataset. At around 5.5 slices/neuron and only 348 mW, it is able to use 33% less area and 4 times as less power per neuron as current state-of-the-art implementations while keeping low simulation step times.

The development and use of highly automated vehicles (HAV) in agriculture is a highly important task because of the lack of machine drivers and unsatisfactory level of their qualifications, reducing the impact of harmful factors on employees of agricultural enterprises. HAVs allow to avoid these problems: increase productivity and the efficiency of seasonal use of equipment, and reduce the impact of harmful factors on people. Modern HAVs in agriculture are based on the following methods: parallel driving according to geo coordinates without automatic turning and without obstacles tracking, and on technical vision without the use of a geographic information system (for example Cognitive AgroPilot) and a digital field map, which makes it impossible to generate the optimal path around the field.

Water electrolysis is a highly efficient route to produce ideally clean H2 fuel with excellent energy conversion efficiency and high gravimetric energy density, without producing carbon trace unlike steam methane reforming, and resolves the issues of environmental contamination via replacing the conventional fossil fuel. Of special importance lies in the advancement of highly effective non-precious catalysts for the oxygen evolution reaction (OER). The electrocatalytic activity of an active catalyst mainly depends on the material conductivity, accessible catalytically active sites, and intrinsic OER reaction kinetics, which can be tuned via introducing heteroatom N in the catalyst stricture. Herein, an efficacious nitrogenation of CuS has been accomplished, which was synthesized using hydrothermal procedure, and characterized for their electrocatalytic activity towards OER. The nitrogen-doped CuO@CuS (N,CuO@CuS) electrocatalyst exhibits superior OER activity than pristine CuS (268 and 602 mV), achieving the low overpotential of 240 and 392 mV at a current density of 10 and 100 mA/cm2, respectively, ascribed to the favorable electronic structural modification triggered by nitrogen incorporation. The N,CuO@CuS also exhibits excellent endurance under varied current rates and a static potential response over 25 h stability measured at 10 and 100 mA/cm2.

Here, we propose a prescriptive simulation model of a process operator’s decision-making assisted by artificial intelligence (AI) algorithm in a technical system control loop. We analyze situations fraught with a catastrophic threat that may cause unacceptable damage. Operators’ decision-making is interpreted in terms of a subjectively admissible probability of disaster and subjectively necessary reliability of its assessment. We distinguish four extreme decision-making strategies corresponding to different ratios between the above variables. An experiment simulating a process facility, an AI algorithm and operator's decision-making strategy was held. It showed that depending on the properties of a controlled process (the speed of hazard onset) and the AI algorithm characteristics (Type I and II error rate), each of such strategies or some intermediate strategy may prove to be more beneficial than others. The same approach is applicable to the identification and analysis of sustainability of strategies applied in real-life operating conditions, as well as to the development of a computer simulator to train operators to control hazardous technological processes using AI-generated advice.

Purpose To alleviate the data imbalance problem caused by subjective and objective reasons, scholars have developed different data preprocessing algorithms, among which undersampling algorithms are widely used because of their fast and efficient performance. However, when the number of samples of some categories in a multi-classification dataset is too small to be processed by sampling, or the number of minority class samples is only 1 to 2, the traditional undersampling algorithms will be weakened. Methods This study selects 9 multi-classification time series datasets with extremely few samples as the objects, fully considers the characteristics of time series data, and uses a three-stage algorithm to alleviate the data imbalance problem. Stage one: Random oversampling with disturbance items increases the number of sample points; Stage two: On this basis, SMOTE (Synthetic Minority Oversampling Technique) oversampling; Stage three: Using dynamic time warping distance to calculate the distance between sample points, identify the sample points of Tomek Links at the boundary, and clean up the boundary noise.Results This study proposes a new sampling algorithm. In the 9 multi-classification time series datasets with extremely few samples, the new sampling algorithm is compared with four classic undersampling algorithms, ENN (Edited Nearest Neighbours), NCR (Neighborhood Cleaning Rule), OSS (One Side Selection) and RENN (Repeated Edited Nearest Neighbours), based on macro accuracy, recall rate and F1-score evaluation indicators. The results show that: In the 9 datasets selected, the dataset with the most categories and the least number of minority class samples, FiftyWords, the accuracy of the new sampling algorithm is 0.7156, far beyond ENN, RENN, OSS and NCR; its recall rate is also better than the four undersampling algorithms used for comparison, at 0.7261; its F1-score is increased by 200.71%, 188.74%, 155.29% and 85.61%, respectively, relative to ENN, RENN, OSS, and NCR; In the other 8 datasets, this new sampling algorithm also shows good indicator scores.Conclusion The new algorithm proposed in this study can effectively alleviate the data imbalance problem of multi-classification time series datasets with many categories and few minority class samples, and at the same time clean up the boundary noise data between classes.

Hybrid reverse osmosis electrodialysis systems make it possible to obtain solutions with a higher concentration of components compared to single electrodialysis treatment, i.e. more efficient separation of brine and pure water. The article proposes experimental and pilot-industrial studies of a hybrid membrane system operation using industrial wastewater for the disposal of liquid waste from an ion-exchange chemical-desalting water treatment plant of a thermal power plant, followed by a calculation of economic efficiency and an analysis of the environmental feasibility of their use. The developed technological scheme offers separate processing of acidic and alkaline waste regeneration solutions using calcium carbonate reagent and desalination on baromembrane and electromembrane units to obtain clean water and dry residue. The hybrid system includes a booster filter press and an evaporator. The hybrid system makes it possible to provide a thermal power plant with a "zero discharge" with a minimum consumption of reagents and electricity, as well as return all water from wastewater to the power plant cycle.

Four previously undescribed highly oxygenated diterpenoids (1–4), zeylleucapenoids A–D, characterized by halimane and labdane skeletons, were isolated from the aerial parts of Leucas zeylanica. Their structures were elucidated primarily by NMR experiments. The absolute configuration of 1 was established by theoretical ECD calculations and X-ray crystallographic analysis, whereas those for 2−4 were assigned by theoretical ORD calculations. Zeylleucapenoid D (4), with an IC₅₀ value of 38.45 μM in RAW264.7 macrophages and nontoxic activity for zebrafish embryo, and obviously inhibited pro-inflammatory cytokines TNF-α and IL-6 in a dose-dependent manner. Compound 4 inhibited of the expression of inducible nitric oxide synthase (iNOS) and cyclooxygenase-2 (COX-2). Furthermore, molecular docking analysis indicated the possible mechanism of action for 4 may be bind to targets by hydrogen- and hydrophobic- bond interactions.

Nowadays, great attention has been attributed to the study of runoff and its fluctuation over space and time. There is a crucial need for a good soil and water management system to overcome the challenges of water scarcity and other natural adverse events like floods and landslides, among others. Rainfall-runoff modeling is an appropriate approach for runoff prediction, making it possible to take preventive measures to avoid damage caused by natural hazards such as floods. In the present study, several data driven models, namely: Multiple linear regression (MLR), Multiple adaptive regression splines (MARS), Support vector machine (SVM), and Random Forest (RF), were used for rainfall-runoff prediction of the Gola watershed, located in the south-eastern part of the Uttarakhand. The performance of the models was evaluated based on the coefficient of determination (R2), root mean square error (RMSE), Nash-Sutcliffe efficiency (NSE), and percent bias (PBAIS) indices. In addition to the numerical comparison, the models were evaluated and their performances were evaluated base on graphical plotting, i.e., line diagram, scatter plot, Violin plot, relative error plot and Taylor diagram (TD). The comparison results revealed that the four heuristic methods gave higher accuracy than the MLR model. Among the machine learning models, the RF (RMSE (m3/s), R2, NSE, and PBIAS (%) = 6.31, 0.96, 0.94, and -0.20 during the training period, respectively, and 5.53, 0.95, 0.92, and -0.20 during the testing period, respectively) surpassed the MARS, SVM, and the MLR models in forecasting daily runoff for all cases studies. Among all four models, the RF model outperformed in the training and testing periods. It can be summarized that the RF model is best-in-class and delivers a strong potential for runoff prediction of the Gola watershed.

Interface solar steam generation (ISSG) are charming for its applications in desalination and wastewater treatment. Biomass is an attractive substrate for utilizing solar vapor evaporators because of its natural pore structure and water transportability. Polymers like polydopamine (PDA) and polypyrrole (PPy) with broadband spectrum absorption are fascinating in photothermal materials (PTMs). Herein, PDA coated daikon-based (PDA-DK) and PPy coated daikon-based (PPy-DK) PTMs have been exploited for solar steam generation. When polyethylene foam (PEF) was used as an insulating layer to limit heat loss from the PTMs to bulk water, the evaporation rate of PDA-DK and PPy-DK was raised from 0.82 kg m–2 h–1 and 0.96 kg m–2 h–1 to 1.50 kg m–2 h–1 and 1.60 kg m–2 h–1, respectively. Meanwhile, the corresponding photothermal conversion efficiency was increased to 89.01% and 98.97%, which was increased by nearly 40% under 1-sun irradiation. In addition, PDA-DK and PPy-DK exhibited remarkable stability for the solar steam generation without significant change through 15 cycles. Furthermore, PDA-DK and PPy-DK could effectively desalt seawater and purify dyeing wastewater. All the results indicate that PDA-DK and PPy-DK have great potential in real-world applications for solar steam generation.

To validate the accuracy and reliability of onboard sensors for object detection and localization in driver assistance, as well as autonomous driving applications under realistic conditions (indoors and outdoors), a novel tracking system is presented. This tracking system is developed to determine the position and orientation of a slow-moving vehicle (e.g. car during parking maneuvers), independent of the onboard sensors, during test maneuvers within a reference environment. One requirement is a 6 degree of freedom (DoF) pose with a position uncertainty below 5 mm (3σ), an orientation uncertainty below 0.3° (3σ) at a frequency higher than 20 Hz, and a latency smaller than 500 ms. To compare the results from the reference system with the vehicle’s onboard system, a synchronization via Precision Time Protocol (PTP) and a system interoperability to Robot Operating System (ROS) is implemented. The developed system combines motion capture cameras mounted in a 360° panorama view set-up on the vehicle with robotic total stations. A point cloud of the test site serves as a digital twin of the environment, in which the movement of the vehicle is simulated. Results have shown that the fused measurements of these sensors complement each other, so that the accuracy requirements for the 6 DoF pose can be met, while allowing a flexible installation in different environments.

In our paper, we develop the hypothesis of a general call for high mobility and discuss the consequences of it. First, we examine the contemporary social representations of mobility, looking for a definition of what is seen as being properly mobile. We will then show how intertwined social representations of space and time result in the prevalent vision of an inevitable and constant mobility. Next, we will thus discuss the importance of seeing mobility as much more than its material facet. Our third step will be to propose a formalisation of the contemporary requisite for mobility. Through four imperatives (activity, activation, participation, adaptation), the mobilitarian ideal requires each person and organisation to be constantly active, mobile, flexible, networking, etc. We argue that, today, we are all meant to be highly mobile. We will illustrate this point with the example of the parliamentary documents of the Belgian Prison Act (2005) in which prison is open and porous, good inmates are described as dynamic individuals on the move and the legitimate penitentiary system is a paradoxical mobilisation system. We will conclude by discussing the need to reshape our vision of the prison, considering its apparently paradoxical relation with mobility.

Patient-derived xenograft (PDX) models are created by engraftment of patients’ tumor tissues into immunocompetent mice. Since PDX model keep the characteristics of primary patient’s tumor such as gene expression profiles and drug sensitivity, it now becomes most reliable in vivo human cancer model. The engraftment rate are increased with the introduction of NOD/Scid based immunocompromised mice, especially, NK cell defective NOD strains such as NOD/Scid/IL2Rγnu (NOG/ NSG) mice and NOD/Scid/Jak3null (NOJ) mice. Success ratio differs from the origin of tumor: Gastrointestinal tumors tend to higher success rate and breast cancer is lower. Subcutaneous transplantation is most popular method to establish PDX, but some tumor needs orthotropic or renal capsule transplantation, and human hormone treatment is needed to establish hormone dependent cancers such as prostate and breast cancer. PDX library with patient’s clinical data, gene-expression patterns, mutational status, drug responsiveness and tumor architecture will be the powerful tool for developing specific biomarker and novel individualized therapy and establishing precision cancer medicine.

Anion exchange membrane (AEM) electrolysis is hampered by two main issues: stability and performance. Focusing on the latter, this work demonstrates a highly active NiMo cathode for hydrogen evolution in AEM electrolysis. We demonstrate an electrolyzer performance of 1 A cm⁻² at 1.9 V (total cell voltage) with a NiMo loading of 5 mg cm⁻² and an iridium black anode in 1 M KOH at 50 °C, that may be compared to 1.8 V for a similar cell with Pt at the cathode. The catalysts developed here will be significant in supporting the pursuit of cheap and environmentally friendly hydrogen fuel.

Tantalum doped ZnO structures (ZnO:Ta) were synthesized and some of their characteristics were studied. ZnO material was deposited on silicon substrates by using a hot filament chemical vapor deposition (HFCVD) reactor. The raw materials were a pill made of a mixture of ZnO and Ta₂O₅ powders, and molecular hydrogen was used as a reactant gas. Percentage of tantalum was varied from 0 to 500 mg by varying the percentage of tantalum oxide in the mixture of the pill source, by holding a fixed amount of 500 mg of ZnO in all experiments. X-ray diffractograms confirmed the presence of zinc oxide in the wurtzite phase and metallic zinc with a hexagonal structure, and no other phase was detected. Displacements to lower angles of reflection peaks, compared with those from samples without contamination, were interpreted as the inclusion of the Ta atoms in the matrix of the ZnO. This fact was confirmed by EDS and XRD measurements. From SEM images from undoped samples exhibited mostly micro sized semi-spherical structures while doped samples displayed a trend to grown as nanocrystalline rods. The presence of tantalum during the synthesis affects the way of the growth. Green photoluminescence at naked eye was observed when Ta doped samples were illuminated by ultraviolet radiation and confirmed by PL spectra. PL intensity on Ta doped ZnO varied from those undoped samples up to 8 times.

This paper presents a new high-efficiency-high-step-up based converter integrating two stype DC-DC Boost and Flyback coupled magnetic converter with recovery stage dedicated to smart HVDC distributed architecture in renewable energy production systems. Appropriate duty cycle ratio assumes that the recovery stage work with parallel charge and discharge to achieve high step-up voltage gain. Besides, the voltage stress on the main switch is reduced with a passive clamp circuit and thus, low on-state resistance Rdson of the main switch can be adopted to reduce conduction losses. The circuit is simple to control. As a final point of this research, the simulation and the prototype investigational results are presented to demonstrate the effectiveness of this proposed converter.

As freshwater sources of drinking water become limited cities and urban areas must consider higher-salinity waters as potential sources of drinking water. The Salton Sea in the Imperial Valley of California has a very high salinity (43 ppt), total dissolved solids (70,000 mg/L) and color (1440 CU). Proposals to desalinate the Salton Sea are expected to lower the equilibrium salinity from 45 ppt to 3 ppt yielding significant benefits for ecological restoration. High salinity eutrophic waters such as the Salton Sea are difficult to treat yet more desirable sources of drinking water are not always available. Jar tests were performed to evaluate the treatability of Salton Sea water for potential urban water use by coagulation using aluminum chlorohydrate, ferric chloride and alum. Coagulation-sedimentation proved to be relatively ineffective for lowering turbidity with no clear optimum dose for any of the coagulants tested. Alum was most effective for color removal (28 percent) at a dose of 40 mg/L. Turbidity was removed effectively with 0.45 m and 0.1 m microfiltration. Bench tests of Salton Sea water using Sea Water Reverse Osmosis (SWRO) achieved rejections of 99 percent salinity, 97.7 percent conductivity, 98.6 percent total dissolved solids, 98.7 percent chloride, 65 percent sulfate, and 99.3 percent turbidity.

Highly photoluminescent C-Dots are prepared by hydrothermal reaction of citric acid and piperazine as dual reason in both hydrolysis and surface passivation agent along with the N-doping agent. The resulting C-Dots without external passivation showed PL enhancement by electron transfer from C-Dots-donor to piperazine-acceptor with the maximum emission yields of more than 84%. After mixing the prepared C-Dots with the mixture of EtOH and acetone (1:1 vol %), a novel washing process was performed by centrifugation to remove the precursors and by-products. The resulting C-Dots showed much better stability than dialysis. For evaluating the possible application of the C-Dots as a fluorescent biological probe which possess the wide dosing window and multicolor properties. The C-Dots were localized in perinuclear vacuole-like structures with granular pattern in cytoplasm sparing the nucleus. No signs of any morphological deterioration like nuclear shrinkage were observed.

The changes in storage loss, water distribution status, gel characteristics, TBARS, total volatile basic nitrogen, and total plate count of cooked reduced-phosphate silver carp surimi batter during cold storage at 4 °C were investigated. The storage loss, content of free water, pH, hardness, TBARS, total volatile basic nitrogen value and total plate count of all cooked reduced-phosphate silver carp surimi batters significantly increased (P < 0.05) with increasing the cold storage time. Meanwhile, the content of immobilized water, whiteness, springiness, and cohesiveness decreased significantly (P < 0.05). At the same cold storage time, the sample of cooked reduced-phosphate silver carp surimi batter has lower water mobility, darker colour and better texture characteristics, but the values of TBARS, total volatile basic nitrogen and total plate count were not significantly different (P > 0.05). To sum up, the use of potassium bicarbonate instead of sodium tripolyphosphate could produce the cooked reduced-phosphate silver carp surimi batter with better water holding capacity and gel characteristics during cold storage.

Exposure to predator scent (PS) has been used as a model of stress associated with danger to life and body integrity. We tested the hypothesis that repeated PS exposure alters the excitability of serotonin (5-HT) neurons of the dorsal raphe nucleus. To study the mechanisms involved, we approached serum and adrenal corticosterone and aldosterone concentrations, as well as cortical brain-derived neurotrophic factor (BDNF) expression. Adult male Sprague-Dawley rats were exposed to PS for ten minutes daily for ten consecutive days. Two weeks after the last exposure, electrophysiological and biochemical assessments were performed. Measurements by in vivo electrophysiology showed increased spontaneous firing activity of 5-HT neurons in rats exposed to PS. PS exposure resulted in reduced serum corticosterone and aldosterone concentrations. Concentrations of both corticosteroids in the adrenal glands, as well as the relative weight of the adrenals, were unaffected. The gene expression of hippocampal BDNF of rats exposed to PS remained unaltered. In conclusion, repeated exposure of rats to PS leads to enhanced firing activity of 5-HT neurons accompanied by reduced serum, but not adrenal aldosterone and corticosterone concentrations. Reduced corticosteroid concentrations in the blood appear to be the result of increased metabolism and/or tissue uptake rather than altered steroidogenesis. The decrease in circulating corticosterone in rats experienced repeated PS may represent part of the mechanisms leading to increased excitability of 5-HT neurons. The increase in 5-HT neuronal firing activity might be an important compensatory mechanism designated to diminish the harmful effects of the repeated PS exposure on the brain.

Objective. It is unknown whether the public accurately estimate socioeconomic health inequality and whether they wish to see it reduced or eliminated. Methods. Representative samples of the UK and US indicated the perceived and ideal lifespan of people working in “higher managerial/professional” and “routine” occupations. We present perceived and desired lifespan ratios for each sample and for key socio-demographic variables. Results. The UK public estimated the lifespan of professionals to be 5.9% longer than routine workers (true value of 5.8%), and 67.8% (UK) and 53.7% (US) participants correctly identified that professionals live longer than routine workers. In both populations, the median respondent expressed equal ideal lifespans for routine workers and professional workers. Conclusion. The UK public appear well-appraised on the average lifespan for professionals and routine workers. Across nationalities and most socio-demographic groups, the median respondent was aware of social class inequalities in lifespan and preferred that they be eliminated.

A 3D graphene foam made of interconnected multilayer graphene flakes was produced on optical fibres (OF) by laser-induced transformation of a polyimide (PI) film coated on the OF cladding. This material, known as la-ser-induced graphene (LIG), was explored in the electrochemical detection and quantification of dopamine (DA) at physiologically relevant concentrations in the presence of the most relevant interfering molecules in biological fluids, ascorbic acid (AA) and uric acid (UA). The measured limit of detection is 100 nM, the linear range is 0.1 to 5 μM and a maximum sensitivity of 5.0 µA µM−1 cm−2 was obtained for LIG decorated with Pt nanoparticles (NPs). Moreover, immunity to AA and UA interference and to fouling was attained by decorating the LIG elec-trode with Pt NPs and coating with Nafion. These figures of merit underlines the potential of these sensors for the quantification of physiologically relevant concentrations of DA in biological fluids, paving the way for the development of hybrid electrochemical/optical sensing actuating platforms in a lab-on-fibre configuration, with relevant applications in biomedical engineering. The advantages of this hybrid arrangement include the possi-bility of in-situ counterproofing, extended measuring ranges, photoelectrochemical detection and the probing of inaccessible places. This elegant approach can also provide a simple and cost-effective way to fabricate biomed-ical devices with extended functionality, such as medical optical probes with added electrochemical capabilities, optogenetics combined with local electrochemical detection, among others.

Transparent conductive electrodes (TCEs) are of enormous significance to the emergence of flexible and wearable electronics and continued growth of modern devices. Versatile and tunable TCEs, featuring with not only high optical transmittance but also intriguing features of electrochemical energy-storage capability, remain a significant challenge. Here we develop capacitive active films comprised of graphene-conjugated V2O5@poly (3,4-ethylene dioxythiophene) ternary composite (V2O5@PEDOT/rGO) on silver nanowire coated substrates as solid-state super/pseudocapacitors. The constructed electrodes exhibit improved electrolyte ions interaction with effective graphene layer, achieving high areal capacitance 0.6-1.2 mF.cm−2 with 0.5M LiCl electrolytes at optical transparency >60% with record durability. As demonstrated, the kinetic blocking of PEDOT layer and anchoring capability of graphene upon amphoteric soluble vanadium ions from layered V2O5 nanoribbons/nanobelts contribute synergistically to the unusual electrochemical stability, also shown using scanning electrochemical microscopy (SECM) providing electroactivity sites and ion transportation rates. As-fabricated symmetric solid-state supercapacitors delivered broad potential window >1.4 V under two different electrolyte environments (aqueous LiCl and LiCl/PVA gel) and demonstrated higher power and energy density (0.27 μWh.cm−2) outperforming previously reported devices at <0.1 μWh.cm−2. The electrochemical properties are also discussed in terms of solvation in polymer gel electrolyte ions.

Recent advances and demands in clinical applications drive a large amount of research to hydroxyapatite (HA) composite coatings fabricated by plasma spray. However, lower degree of HA crystallinity related to high temperature exposure in plasma spray usually leads to rapid weakening and disintegration of HA coatings and often promotes inflammatory responses in the surrounding tissue. In this research, graphene nanosheet (GNS) reinforced HA coatings were fabricated using plasma spray and followed by heat and hydrothermal treatment (hereafter referred to as thermal treatment). The addition of GNSs resulted in competing phenomenon to influence HA crystallinity viz. increased portion of the partially melted/unmelted zones and higher cooling rate during splat formation, leading to slight increase in HA crystallinity (~46.0-51.3%) in the as-sprayed coating. XRD and FTIR results showed that thermal treatment was capable of inducing significant transformation of amorphous HA to the crystalline form and removing other foreign non-HA compounds through regaining OH- ion, and therefore HA coatings displayed ~45.5-47.1% improvements in HA crystallinity regardless of addition or not of the GNS nanofillers. Microstructure observations revealed that thermal treatment enabled microcrack propagation due to stresses caused by crystallisation and phase transformations, and the residual partially melted/unmelted zone of the thermally treated GNS/HA coating was significantly decreased in size. More importantly, the added GNSs contributed greatly to the significant increase in surface nanoroughness of the thermally treated HA coatings owing to the fact that much more structural defects along with the GNSs mainly induced by thermal treatment might act as nucleation sites to accelerate HA nanoparticle precipitation, which would be beneficial for the improved adhesion strength of the osteoblast cells on the coating surface.

Space–air–ground integrated network (SAGIN) is considered as an enabler for the sixth-generation (6G) networks. By integrating terrestrial and non-terrestrial (satellite, aerial) networks, SAGIN seem to be a quite promising solution to provide reliable connectivity everywhere and all the time. Their availability can be further enhanced if hybrid free space optical (FSO)/radio frequency (RF) links are adopted. In this paper, the performance of a hybrid FSO/RF communication system operating in SAGIN has been analytically evaluated. In the considered system, a high altitude platform station (HAPS) is used to forward the satellite signal to the ground station. Moreover, the FSO channel model assumed takes into account the turbulence, pointing errors and path losses, while for the RF links, a relatively new composite fading model has been considered. In this context, a new link selection scheme has been proposed that is designed to reduced the signaling overhead required for the switching operations between the RF and FSO links. The analytical framework that has been developed is based on the Markov chain theory. Capitalizing on this framework, the performance of the system has been investigated using the criteria of outage probability and the average number of link estimations. The numerical results presented reveal that the new selection scheme offers a good compromise between performance and complexity.

Triple negative breast cancer (TNBC) is the most aggressive breast cancer accounting for around 15% of identified breast cancer cases. TNBC, by lacking estrogen receptor (ER), progesterone receptor (PR), and human epidermal growth factor receptor 2 (HER2), is unresponsive to current targeted therapies. Existing treatment relies on chemotherapeutic treatment but, despite an initial response to chemotherapy, the inception of resistance and relapse is unfortunately common. Dasatinib is an approved second-generation inhibitor of multiple tyrosine kinases and literature data strongly support its use in the management of TNBC. However, dasatinib binds to plasma proteins and undergoes extensive metabolism through oxidation and conjugation. To protect dasatinib from fast pharmacokinetic degradation and to prolong its activity, it was encapsulated on poly(styrene-co-maleic acid) (SMA) micelles. The obtained SMA-dasatinib nanoparticles (NPs) were evaluated for their physicochemical properties, in vitro antiproliferative activity in different TNBC cell lines, and in vivo anticancer activity in a syngeneic model of breast cancer. Obtained results showed that SMA-dasatinib is more potent against 4T1 TNBC tumor growth in vivo compared to free drug. This enhanced effect was ascribed to the encapsulation of the drug protecting it from a rapid metabolism. Our finding highlights the often-overlooked value of nanoformulations in protecting its cargo from degradation. Overall, results may provide an alternative therapeutic strategy for TNBC management.

This work is devoted to consideration and analysis of the application of molecular dynamics simulation (MDS) methods to the study of nanosized polymer polyvinylidene fluoride (PVDF) thin ferroelectric films (two-dimensional ferroelectrics) and their composites with graphene layers: 1) to study and calculations of the polarization switching time depending on the electric field and PVDF film thickness; 2) to study and calculations of the polarization switching time depending changes of the PVDF on PVDF-TrFE film; 3) to study the polarization switching time in PVDF under influence of graphene layers. All calculations at each MDS step were carried out using quantum semi-empirical methods PM3. A comparison and analysis of the results of these calculations and the kinetics of polarization switching within the framework of the Landau-Ginzburg-Devonshire theory for homogeneous switching in ferroelectric polymer films is carried out. The study of the composite heterostructures of the “graphene-PVDF” type and calculations of their polarization switching times were presented too. It is shown that replacing PVDF with PVDF-TrFE significantly changes the polarization switching times in these thin polymer films, and that introducing various graphene layers into the PVDF layered structure leads to both an increase and a decrease in the polarization switching time. Here everything also depends on the position and displacement of the ferroelectric coercive field depending on the system damping parameters.

If a lubricant contains structures capable of conducting energy, reactions involving zinc dialkyldithiophosphate (ZDDP) may take place both very close to and away from the solid surfaces, with this indicating that ZDDP can be a highly effective anti-wear (AW) additive. The central thesis of this article is that the tribocatalytic effect is observed only when the energy emitted by the solids is transmitted by ordered molecular structures present in the lubricant, e.g., graphene. The friction tests were carried out for 100Cr6 steel balls in a sliding contact with uncoated or a:C-H-coated HS6-5-2C steel discs in the presence of polyalphaolefin 8 (PAO 8) as the lubricant, which was enhanced with graphene and/or ZDDP. There is sufficient evidence of the interactions occurring between ZDDP and graphene and their effects on the tribological performance of the system. It was also found that the higher the concentration of zinc in the wear area, the lower the wear. This was probably due to the energy transfer resulting from the catalytic decomposition of ZDDP molecules. Graphene, playing the role of the catalyst, contributed to that energy transfer.

This study explores the enhancement of aqueous zinc-ion batteries (AZIBs) using ammonium-enhanced vanadium oxide cathodes. Density Functional Theory (DFT) calculations reveal that NH₄⁺ incorporation into V₆O₁₆ lattices significantly facilitates Zn²⁺ ion diffusion by reducing electrostatic interactions, acting as a structural lubricant. Subsequent experimental validation using (NH₄)₂V₆O₁₆ cathodes synthesized via a hydrothermal method corroborates the DFT findings, demonstrating remarkable electrochemical stability with a capacity retention of 90% after 2000 cycles at 5 A g⁻¹. These results underscore the potential of NH₄⁺ in improving the performance and longevity of AZIBs, providing a pathway for sustainable energy storage solutions.

Although 4Ce4YSZ has high corrosion resistance, it faces challenges concerning sinterability and ionic conductivity. Therefore, we studied destabilization behavior caused by corrosion and oxygen vacancy ordering according to ZnO doping. The powders of (4Ce4YSZ)1-x(ZnO)x (x=0.5, 1, 2, 4 mol%) were synthesized through the sol-gel method. With the addition of ZnO, the cubic phase increased, and secondary phases were not observed. The (111) peak showed a higher angle shift in ZnO-doped 4Ce4YSZ compared to 4Ce4YSZ, and TEM-SAED revealed a reduction in the spacing of the (011)t plane, suggesting lattice contraction due to the substitution of the smaller Zn2+ (60 Å) for Zr4+ (84 Å) in the lattice. The local atomic structure analysis was conducted using EXAFS to investigate the oxygen vacancy ordering behavior. Zr K-edge Fourier-transform data revealed a decrease in the Zr-O1 peak intensity with an increasing amount o ZnO doping, indicating an increase in oxygen vacancies. The Zr-O1 peak position shifted to the right, leading to an increase in the Zr-O1 interatomic distance. In the Y K-edge Fourier-transform data, the Y-O1 peak intensity did not decrease, and there was little variation in the Y-O1 interatomic distance. These results suggest that the oxygen vacancies formed due to ZnO doping are located in the neighboring oxygen shell of Zn, rather than in the neighboring oxygen shells of Y and Zr. Impedance measurements were conducted to measure the conductivity, and as the amount of ZnO doping increased, the total conductivity increased, while the activation energy decreased. The increase in oxygen vacancies by ZnO doping contributed to the enhancement of conductivity and it is considered that these created oxygen vacancies did not interact with Zn2+ and did not form defect associations. Fluoride-based molten salts were introduced to the specimens to assess corrosion behavior in a molten salt environment. Yttrium depletion layers (YDLs) were formed on the surfaces of all specimens due to the leaching of yttrium. However, Ce remained relatively stable at the interface according to EDS line scans, suggesting a reduction in the phase transformation (cubic, tetragonal to monoclinic) typically associated with yttrium leaching in YSZ.

Incorporating nanoparticles into plant cultivation has been shown to improve growth parameters and alter the bioactive component compositions of many plant species, including Curcumin longa. The aim of the current study was to investigate the effects of foliar application of zinc oxide na-noparticles on the content of bioactive compounds and their antibacterial activities against poten-tial bacterial pathogens. To this end, C. longa leaves were treated with different doses of ZnO NPs to see how they affected bioactive component composition. The effect of different doses of ZnO NPs on the accumulation of bisdemethoxycurcumin, demethoxycurcumin, and curcumin in etha-nolic extracts of C. longa rhizomes was evaluated using high-performance liquid chromatography (HPLC). When compared to the control treatment, foliar spraying with (5 and 40 mgL-1) ZnO NPs increased bisdemethoxycurcumin, demethoxycurcumin, and curcumin levels by approximately (2.69 and 2.84), (2.61 and 3.22), and (2.90 and 3.45) fold, respectively. It was looked at to see if the ethanolic extracts made from the plantlets might change in terms of their phytochemical makeup and antibacterial properties. Furthermore, the results revealed that C. long-ZnO-NPs displayed antibacterial activity against S. aureus and P. aeruginosa tested bacterium strains, but made little attempt against E. coli. The MIC for P. aeruginosa was 100 g/mL. Time-kill studies also revealed that ZnO-NPs at 4 MIC killed P. aeruginosa, Actinobacteria baumannii, and Bacillus sp. after 2 hours, while S. aureus did not grow when treated with 4xMIC of the extract for 6 hours. The strongest antibacterial activity was seen with extract from plantlets grown without nanoparticles for P. aeruginosa, whereas it was seen with extract from plantlets grown in the presence of 5 mg/L ZnO-NPs for E. coli, S. aureus, and P. aeruginosa. These findings show that ZnO-NPs are a pow-erful enhancer of bioactive compound production in C. longa, a trait that can be used to combat antibiotic resistance in pathogenic bacterial species.

Sorption of pure CO2 and CH4 and CO2/CH4 binary gas mixtures in amorphous glassy Poly(2,6-dimethyl-1,4-phenylene) oxide (PPO) at 35°C up to 1000 Torr is investigated. Sorption experiments were carried out using an approach that combines barometry with FTIR spectroscopy in the transmission mode to quantify the sorption of pure and mixed gases in polymers. The pressure range is chosen to prevent any variation of the glassy polymer density. The solubility within the polymer of the CO2 present in the gaseous binary mixtures is practically coincident with the solubility of pure gaseous CO2, up to a total pressure of the gaseous mixtures equal to 1000 Torr and for CO2 mole fraction of ~0.5 mol mol-1 and ~0.3 mol mol-1. The Non-Equilibrium Thermodynamics for Glassy Polymers (NET-GP) modelling approach has been applied to the Non-Random Hydrogen Bonding (NRHB) lattice fluid model to fit the solubility data of pure gases. We have assumed here that no specific interactions are occurring between the matrix and the absorbed gas. The same thermodynamic approach has been then used to predict the solubility of CO2/CH4 mixed gases in PPO resulting in a deviation lower than 9.5% from the experimental results for CO2 solubility.

Iron oxide nanozymes are a form of nanomaterial with both superparamagnetic and enzyme-mimicking properties. Given the multifunctional nature of iron oxide nanozymes, it is attractive for creating iron oxide hybrid nanozymes through biomolecular modifications to imbue with auxillary properties. Such iron oxide hybrid nanozymes can be useful for rapid and cost-effective analysis of circulating tumor nucleic acids (ctNAs) in patient liquid biopsies during minimal residual disease (MRD) monitoring of cancer recurrence. Herein, the use of streptavidin-modified iron oxide hybrid nanozymes is reported for magnetic enrichment and bioelectrocatalytic sensing of three prostate cancer (PCa) ctRNA biomarkers with high detection specificity and sensitivity (10 copies) over an ultrabroad dynamic range (five orders of magnitude). Furthermore, the feasibility of ctRNA analysis for pre- and post-cancer treatment MRD monitoring is demonstrated using PCa urinary liquid biopsy samples.

Transparent conducting oxides (TCO) with high electrical conductivity and at the same time high transparency in the visible spectrum are an important class of materials widely used in many devices requiring a transparent contact such as light-emitting diodes, solar cells and display screens. Since the improvement of electrical conductivity usually leads to degradation of optical transparency, a fine-tuning sample preparation process and a better understanding of the correlation between structural and transport properties is necessary for optimizing the properties of TCO for use in such devices. Here we report a structural and magnetotransport study of tin oxide (SnO₂), a well-known and commonly used TCO, prepared by a simple and relatively cheap Atmospheric Pressure Chemical Vapour Deposition (APCVD) method in the form of thin films deposited on soda-lime glass substrates. The thin films were deposited at two different temperatures (which were previously found to be close to optimum for our setup), 590 °C and 610 °C, and with (doped) or without (undoped) the addition of fluorine dopants. Scanning Electron Microscopy (SEM) and Grazing Incidence X-ray Diffraction (GIXRD) revealed the presence of inhomogeneity in the samples, on a bigger scale in form of grains (80–200 nm), and on a smaller scale in form of crystallites (10–25 nm). Charge carrier density and mobility extracted from DC resistivity and Hall effect measurements were in the ranges 1–3 × 10²⁰ cm⁻³ and 10–20 cm²/Vs, which are typical values for SnO₂ films, and show a negligible temperature dependence from room temperature down to -269 °C. Such behaviour is ascribed to grain boundary scattering, with the interior of the grains degenerately doped (i.e., the Fermi level is situated well above the conduction band minimum) and with negligible electrostatic barriers at the grain boundaries (due to high dopant concentration). The observed difference for factor 2 in mobility among the thin-film SnO₂ samples most likely arises due to the difference in the preferred orientation of crystallites (texture coefficient).

In this paper we present magnetoelectric properties of metal/metal-oxide/metal junctions. We use Ti and Fe as metallic layers separated by the porous metal-oxides of iron or titanium formed with the anodization method. This allowed to prepare double junctions with at least one ferromagnetic layer. Here we show magnetoresistance and current-voltage characteristics of the junctions together with their magnetic characteristics. We found positive or negative magnetoresistance depending on junction composition. We discuss also the nature of differential resistance calculated from I-V characteristics. Our findings show that the strongest influence on observed behaviour has a top metallic layer and the interface between this layer and anodized oxide where strong interatomic diffusion is expected.

Lithium-rich layered oxides is one of the most perspective candidates for cathode materials of lithium ion battery, because of its high discharge capacity. However, there are some disadvantages of uneven composition, voltage decay, and poor rate capacity, which are closely related to the preparation method. Here, 0.5Li2MnO3·0.5LiMn0.8Ni0.1Co0.1O2 were successfully prepared by sol-gel and oxalate co-precipitation methods. A systematic analysis of the materials shows that the 0.5Li2MnO3·0.5LiMn0.8Ni0.1Co0.1O2 prepared by the oxalic acid co-precipitation method has the most stable layered structure and the best electrochemical performance. The initial discharge specific capacity is 261.6 mAh·g-1 at 0.05 C, and the discharge specific capacity is 138 mAh·g-1 at 5 C. The voltage decay is only 210 mV, and the capacity retention is 94.2% after 100 cycles at 1 C. The suppression of voltage decay can be attributed to the high nickel content and uniform element distribution. In addition, tightly packed porous spheres help to reduce lithium ion diffusion energy and improve the stability of the layered structure, thereby improving cycle stability and rate capacity. This conclusion provides a reference for designing high energy density lithium-ion batteries.

An effective approach to fabricate large-scale of conducting polyaniline (PANI) by an in situ anodic electrochemical polymerization on the nickel foam, which coated by a novel aryl diazonium salt (ADS)-functionalized graphene (ADS-G). In present work, ADS-G was used as a high surface area support material for electrochemical polymerization of PANI. Electrochemical performances of the ADS-G/PANI composites exhibited better suitability as supercapacitor electrode materials than that of the PANI. The ADS-G/PANI composites achieved the specific capacitance of 528 F g-1, which was higher than that of PANI (266 F g-1) due to the excellent electrode-electrolyte interaction and synergistic effect of electrical conductivity between ADS-G and PANI in the composites. These findings suggested that the ADS-G/PANI composites were a suitable composite for the potential supercapacitor applications.

We explore the implementation of specific optical properties of armchair graphene nanoribbons (AGNRs) through edge-defect manipulation. This technique employs the tight-binding model in conjunction with the calculated absorption spectral function. Modification of the edge states gives rise to the diverse electronic structures with striking changes in the band gap and special flat bands at low energy. The optical-absorption spectra exhibit exotic excitation peaks and they strongly depend on the type and period of the edge extension. Remarkably, there exist the unusual transition channels associated with the flat bands for selected edge-modified systems. We discover the special rule governing how the edge-defect influences the electronic and optical properties in AGNRs. Our theoretical prediction demonstrates an efficient way to manipulate the optical properties of AGNRs. This might be of importance in the search for suitable materials designed to have possible technology applications in nano-optical, plasmonic and optoelectronic devices.

Graphene and borophene are highly attractive two-dimensional materials with outstanding physical properties. In this study we employed a combined atomistic continuum multiscale modeling to explore the effective thermal conductivity of polymers nanocomposites made of PDMS polymer as the matrix and graphene and borophene as nanofillers. We first conduct classical molecular dynamics simulations to investigate the interfacial thermal conductance between graphene/PDMS and borophene/PDMS interfaces. Acquired results confirm that the interfacial thermal conductance between nanosheets and polymer increases from the single-layer to multilayered nanosheets and finally converges. The data provided by the atomistic simulations were then used in the finite element method simulations to evaluate the effective thermal conductivity of polymer nanocomposites at continuum level. We explore the effects of nanofillers type, their volume content, geometry aspect ratio and thickness on the nanocomposites effective thermal conductivity. As a very interesting finding, we show that borophene nanosheets, despite almost two orders of magnitude lower thermal conductivity than graphene, can yield very close enhancement in the effective thermal conductivity in comparison with graphene, particularly for low volume content and small aspect ratios and thicknesses. We conclude that for the polymer-based nanocomposites, significant improvement in the thermal conductivity can be reached by improving the bonding between the fillers and polymer or in another word enhancing the thermal conductance at the interface. By taking into account the high electrical conductivity of borophene, our results suggest borophene nanosheets as promising nanofillers to simultaneously enhance the polymers thermal and electrical conductivity.

The present study investigated the effects of alloying and nano-reinforcement on the mechanical properties (microhardness, tensile strength, and compressive strength) of Mg-based alloys and composites. Pure Mg, Mg-3Sn alloy, and Mg-3Sn+0.2GNP alloy-nanocomposite were synthesized by powder metallurgy followed by hot extrusion. The microstructural characteristics of the bulk extruded samples were explored using X-ray diffraction, field-emission scanning electron microscopy, and optical microscopy and their mechanical properties were compared. The microhardness, tensile strength, and compressive strength of the Mg-3Sn alloy improved when compared to those of monolithic Mg sample and further improvements were displayed by Mg-3Sn+0.2GNP alloy-nanocomposite. No significant change in the compressive strain to failure was observed in both the alloy and the alloy-nanocomposite with respect to that of the pure Mg sample. However, an enhanced tensile strain to failure was displayed by both the alloy and the alloy-nanocomposite.