Pain is an unpleasant emotional and sensory experience. For many years orthodontists have been looking for an effective method of reducing this feeling of discomfort. In recent years, low-level laser therapy (LLLT) has taken hold in the orthodontic field. Among the countless advantages it can modulate the painful feeling. The aim of this research is to identify the use of photobiomodulation in subjects undergoing fixed orthodontic treatment, to reduce the pain and discomfort that it causes. The research was conducted from the Web of Science, Pubmed and Scopus databases. Only 14 of all articles met the inclusion and exclusion criteria and were therefore used to conduct the research. The different studies compared, in most cases, patients whose mouth was divided into a part treated with laser therapy and a placebo part. The results show a statistically significant difference in perceived pain between the irradiated arch and the non-irradiated arch. Three authors didn’t find statistically significant results in favour of low-laser therapy, but it is important to remember that they used different parameters. To obtain generally valid studies, with consistent and reproducible results, it is necessary to standardize the different parameters used that are independent by operator performing the procedure.

Spatial light modulators (SLMs) have been widely used to achieve dynamic control of optical traps. Often, holographic optical tweezers have been presumed to provide nanometer or sub-nanometer positioning accuracy. It is known that some features concerning the digitalized structure of SLMs cause a loss in steering efficiency of the optical trap, but their effect on trap positioning accuracy has been scarcely analyzed. On the one hand, the SLM look-up-table, which we found to depend on laser power, produces positioning deviations when the trap is moved at the micron scale. On the other hand, phase quantization, which makes linear phase gratings become phase staircase profiles, leads to unexpected local errors in the steering angle. We have tracked optically-trapped microspheres with sub-nanometer accuracy to study the effects on trap positioning, which can be as high as 2 nm in certain cases. We have also implemented a correction strategy that enabled the reduction of errors down to 0.3 nm.

One of the challenges facing the industrial adoption of additively manufactured parts is the surface roughness on the as-built part. The surface roughness of parts is frequently characterized by metrics specified by international standards organizations. However, these standards list many surface metrics that can make it unclear which to use to best describe the surface. In this work, the ability of the various surface metrics to successfully classify the as-built and post-processed surfaces is studied using linear classification models. Laser polishing via remelting and manual grinding are the post-processing techniques used to smooth the as-built surface. The ability of the linear classifier to successfully categorize the various surfaces is demonstrated, and the various surface metrics are ranked according to the strength of their individual ability to classify the surfaces. This work promotes the method as a potential way to autonomously classify as-built and laser polished surfaces.

The study examined the effect of noninvasive crown retrieval/reuse process using erbium-doped yttrium aluminum garnet laser (Er:YAG). Twenty-six extracted human teeth were prepared for a crown. The crown was milled using lithium disilicate (LD) and zirconia (Z) materials, n=13 per group, 3 for scanning electron microscopy (SEM). The crown was luted using composite resin cement and subjected to a laser retrieval process. After the retrieval process, the crown was cleaned, recemented and laser-retrieved two more times, without and with additional tooth reduction mimicking clinical refreshment of dentin. Retrieval time and temperature were analyzed using analysis of variance (ANOVA). Surface changes were observed through SEM. The retrieval times were 267.1±130.43, 220±79.09, 277.1±126.44, 368.4±136.14, 355±159.39, and 419.2±121.36 seconds for first, second, third LD and Z groups, respectively (p=.009). The maximal temperatures were 23.95.1±1.89°C, 24.86±2.01°C, 24.17±1.53°C, 22.88±1.51°C, 24.03±1.74°C, and 21.99±1.32°C for for first, second, third LD and Z groups, respectively (p=.006). Er:YAG laser crown removal is an effective retrieval tool for all-ceramic crowns. Minimal changes to teeth and crowns were observed following laser irradiation.

The interest in dry EEG electrodes has increased in recent years and especially as everyday suitability earplugs for measuring drowsiness or focus of auditory attention. However, the challenge is still the need for a good electrode material, which is reliable and can be easily processed for highly personalized applications. Laser processing as used here is a fast and very precise method to produce personalized electrode configurations that meet the high requirements of in-ear EEG electrodes, for example. The arrangement of the electrodes on the very flexible and compressible mats allows an exact alignment of the electrodes to the ear mold and contributes to a high wearing comfort, as no edges or metal protrusions are present. For better transmission properties, an adapted coating process for surface enlargement of platinum electrodes is used, which allows easy control of the thickness and growth form of the porous layer. The porous platinum-copper alloy is chemically very stable, shows no exposed copper residues and enlarges the effective surface area by 40. In a proof-of-principle experiment, these porous platinum electrodes could be used to measure the Berger effect in a dry state using just one ear of a test person. Their signal-to-noise ration and frequency transfer function is comparable to gel-based silver/silver chloride electrodes.

Beam dumps are indispensable components for particle accelerator facilities to absorb or dispose beam kinetic energy in a safe way. However, the design of beam dumps based on conventional technology, i.e. the energy deposition via beam-dense matter interaction, makes the beam dump facility complicated and large in size, partly due to nowadays’ high beam intensities and energies achieved. In addition, these high-power beams generate radioactive hazards, which need specific methods to deal with. On the other hand, the EuPRAXIA project can advance the laser-plasma accelerator significantly by achieving 1-5 GeV high quality electron beam in a compact layout. Nevertheless, the beam dump based on conventional technique will still produce radiation hazards and make the overall footprint less compact. Here, we propose to implement a plasma beam dump to absorb the kinetic energy from the EuPRAXIA beam. In doing so, the overall compactness of the EuPRAXIA layout will not be impacted, and the radioactivity generated by the facility can be mitigated. In this paper, results from particle-in-cell (PIC) simulations are presented for plasma beam dumps based on EuPRAXIA beam parameters.

Laser scanning is an effective tool for acquiring geometric attributes of trees and vegetation, which lays a solid foundation for 3-dimensional tree modelling. Existing studies on tree modelling from laser scanning data are vast. Nevertheless, some works don’t ensure sufficient modelling accuracy, while some other works are mainly rule-based and therefore highly depend on user inputs. In this paper, we propose a novel method to accurately and automatically reconstruct tree branches from laser scans. We first extract an initial tree skeleton from the input tree point cloud, then simplify the skeleton through iteratively removing redundant components. A global-optimization approach is performed to fit a sequence of cylinders to approximate the geometry of the tree branches. Experiments on various types of trees from different data sources demonstrate the effectiveness and robustness of our method. The resulted tree models can be further applied in the precise estimation of tree attributes, urban landscape visualization, etc.

Inorganic and organic – inorganic (hybrid) perovskite semiconductor materials have attracted the worldwide scientific attention and research effort as the new wonder material in optoelectronics. Their excellent physical and electronic properties have been exploited to boost the solar cells efficiency beyond 23% and captivate their potential as competitors to the dominant silicon solar cells technology. However, the fundamental principles in Physics dictate that an excellent material for photovoltaic applications must be also an excellent light emitter. This has been realized for the case of perovskite based light emitting diodes (LEDs) but much less for the case of the respective laser devices. Here, the strides have been made since 2014 are presented for the first time. The solution processability, low temperature crystallization, formation of nearly defect free, nanostructures, the long range ambipolar transport, the direct energy band gap, the high spectral emission tunability over the entire visible spectrum and the almost 100% external luminescence efficiency show perovskite semiconductors’ potential to transform the nanophotonics sector. The operational principles, the various adopted material and laser configurations along the future challenges are reviewed and presented in this paper.

Being able to forecast events is of great importance in many fields, from brain behavior to earthquakes or stock markets. Because each dynamical system has intrinsic features, different statistical tools have to be used for each system. Here we study the time series of the output intensity of a fiber laser with an ordinal patterns analysis, and we look for temporal correlations in order to statistically forecast the most intense events. We set two thresholds, a low one and a high one, to distinguish between low intensity versus high intensity events. We find that when the time series is performing events below the low threshold it shows some preferred temporal patterns before performing events above a high threshold.

For development and successful application of any material, a clear understanding of their mechanical behavior is one of the most important things, but when it comes to nanofibers networks it become a challenge due to, their high porosity, many scales in their structure, and characteristics non-linear. Therefore, an experimental methodology in conjunction with a theoretical model that can fully consider their characteristics is still needed. In this work we proposed a model that incorporates the propagation of the elastic waves in two-phase media to determine the effective elastic modulus of electrospun membranes of PLA/gelatin given the mechanical properties of nanofibers, shape, distribution and concentration. The model was verified via laser ultrasonic testing. It was found that the values predicted for the effective modulus by the model were higher than the values obtained from experimental results. One explanation is due to the experimental density. As a result, the P-Wave velocity from the model best fit to experimental results and it has the same behavior, decrees as the concentration of gelatin in the solution. These results indicate the model and experimental methodology can assist in the dressing of nanofibers networks and electrospun materials.

The purpose of this study consists to verify if Er:YAG laser, at low fluences, is able to debond porcelain veneers, successfully used to improve anterior tooth esthetics, without damaging the tooth structures. A total of twelve freshly extracted teeth were used and samples were decontaminated, stored, prepared to obtain Veneers adhesion. One week after, Er:YAG laser with a non-contact sapphire tip with air-water spray was used for veneer debonding at 100 mJ of power and 30Hz of frequency (Fluence 5.91 J/cm2). Results demonstrated that veneer debonding is possible with an Er:YAG laser and that the total number of pulses does not seem related to its efficiency. SEM observation confirms that residual tooth structure is not altered when using these low fluences. Low fluences with Er:YAG laser are able to debond veneers while preserving the tooth structures. SEM observation confirmed that residual tooth structure is not altered with low fluences.

The development of organ-on-chip and biological scaffolds is currently requiring simpler methods to microstructure biocompatible materials in three dimensions, fabricate structural and functional elements in biomaterials or modify the physicochemical properties of desired substrates. Aiming at addressing this need, a low-power CD-DVD-Blu-ray laser pickup head was mounted on a programmable three-axis micro-displacement system in order to modify the surface of polymeric materials in a local fashion. Thanks to a specially-designed method using a strongly absorbing additive coating the materials of interest, it has been possible to establish and precisely control processes useful in microtechnology for biomedical applications. The system was upgraded with blu-ray laser for additive manufacturing and ablation on a single platform. In this work, we present the application of these fabrication techniques to the development of biomimetic cellular culture platforms thanks to the simple integration of several features typically achieved with traditional, less cost-effective microtechnology methods in one step or through replica-molding. Our straightforward approach indeed enables great control of local laser microablation or polymerization for true on-demand biomimetic micropatterned designs in transparent polymers and hydrogels and is allowing integration of microfluidics, microelectronics, surface microstructuring and transfer of superficial protein micropatterns on a variety of biocompatible materials.

Auricular keloids pose significant aesthetic and functional challenges, and traditional treatments often fall short in ad-dressing these. Our study presents an innovative combined approach of ablative CO2 and dye laser therapy for improved keloid management. This treatment protocol was applied to 15 patients with auricular keloids after an initial multispec-tral analysis to assess keloid composition. The laser sequence was tailored per patient based on this analysis. Evalua-tions using the Vancouver Scar Scale and Patient and Observer Scar Assessment Scale were carried out at baseline and at 3-week intervals post-treatment. The results showed a significant reduction in these scores at the final follow-up (p<0.05), suggesting improvements in keloid color, texture, and pliability, with minimal adverse events. Additionally, no recur-rence of keloids was observed. Our findings indicate that this novel methodology of multispectral analysis followed by tailored laser therapy may offer a safe and effective solution for auricular keloids, promising enhanced keloid treatment and prevention of recurrence. However, further investigations, including randomized controlled trials, are needed to confirm and optimize this treatment protocol.

This work communicates analysis of aluminum monoxide, AlO, laser-plasma emission records using line strength data and the ExoMol astrophysical database. A nonlinear fitting program computes comparisons of measured and simulated diatomic molecular spectra. Predicted cyanide spectra of the AlO, ${\rm B}\ ^2\,\Sigma^+ \longrightarrow {\rm X} \ ^2\,\Sigma^+$, $\Delta {\rm v} = 0, \pm 1, \pm 2, + 3$ sequences and progressions compare nicely with 1 nanometer resolution experimental results. The analysis discusses experiment data captured during laser ablation of Al$_2$O$_3$ with 266-nm, 6-mJ pulses. The accuracy of the AlO line strength data is better than one picometer. This work presents as well comparison of the $^{27}$Al$^{16}$O line strength and of ExoMol data for spectral resolutions of 0.1nm and 0.07nm. Accurate AlO databases show a volley of applications in laboratory and astrophysical plasma diagnosis.

This work communicates laser-plasma experiments in a gaseous mixture of hydrogen and nitrogen. Time-resolved spectroscopy measures the first four Balmer series hydrogen lines together with selected neutral and ionized nitrogen lines. Optical breakdown plasma is generated in a 1:1 hydrogen:nitrogen mixture at ambient temperature and 0.27-atm pressure. Time-resolved spectroscopy records emitted radiation with spatial resolution along the slit height for the H_α, H_β, H_γ, and H_δ lines. For 13 selected time delays from 0.25 µs to 3.25 µs and 0.025 µ gate-widths, micro-plasma diagnostics is evaluated. Of interest are the peak-separation and width of H_δ and width of H_γ for electron densities in the range of 0.1 to 1.0×10¹⁷ cm^-3, and comparisons with H_β and H_α diagnostics. Integral inversions interrogate spatial distributions of the plasma expansion. Applications include laboratory and stellar astrophysics plasma diagnosis.

A useful and increasingly common additive manufacturing (AM) process is the selective laser melting (SLM) or direct metal laser sintering (DMLS) process. SLM/DMLS can produce full-density metal parts from difficult materials, but it tends to suffer from severe residual stresses introduced during processing. This limits the usefulness and applicability of the process, particularly in the fabrication of parts with delicate overhanging and protruding features. The purpose of this study was to examine the current insight and progress made toward understanding and eliminating the problem in overhanging and protruding structures. To accomplish this, a survey of literature was undertaken, focusing on process modeling (general, heat transfer, stress and distortion, and material models), direct process control (input and environmental control, hardware-in-the-loop monitoring, parameter optimization, and post-processing), experiment development (methods for evaluation, optical and mechanical process monitoring, imaging, and design-of-experiments), support structure optimization, and overhang feature design; approximately 140 published works were examined. The major findings of this study were that a small minority of the literature on SLM/DMLS deals explicitly with the overhanging stress problem, but some fundamental work has been done on the problem. Implications, needs, and potential future research directions are discussed in-depth in light of the present review.

Background: biophysical stimulation therapy, and in particular Pulsed Electromagnetic Fields (PEMFs) and capacitively coupled electric fields (CCEFs) has significantly increased in the last twenty years. For this, it is necessary to have clear information regarding the efficacy, the therapeutic indication and the expected objectives. Methods: we conducted a narrative review taking into consideration different types of studies with different areas of application. The objective was to take into consideration and analyze the different fields of use and the relevant information present in the literature. Results: There is unanimous opinion regarding the usefulness of applying biophysical therapy on the bone compartment both in terms of the tissue healing process and the symptoms associated with this situation. Differently, but no less importantly, in the joint compartment positive opinions were observed mainly on the inflammatory and catabolic process, however, at present,we did not report evidence regarding cartilaginous tissue regeneration. Conclusion: the effectiveness of PEMFs and CCEFs on the bone healing process in the Orthopedic and Traumatology fields is consolidated evidence in the literature. We have also found positive results on symptoms and patient compliance with rehabilitation therapies. Therefore, notable application can be envisaged in the fields of Prosthetic Surgery and Sports Medicine.

This paper is a mini literature review about electromagnetic field’s effects on cells, tissues and new treatment modalities. We have reviewed a papers which have been published in high quality journals in the last 5 years as two authors. This review’s aim is to be a resource for experimental studies about electricity’s effects on cell biology and pathophysiology. As a result of this literature review, we found that especially extremely low electric frequency and intermediate frequency fields have very important pathophysiological effects. We have mentioned four important expressions on this subject; electroporation, electrofusion, electrochemotherapy, gene electrotransference. Two different new treatment approaches have been developed by use of these two important electrical waves. First is tumor treating fields and the other is pulsed electric fields. Most studies in literature have been done with extremely low frequency and pulsed electric fields. In terms of diseases, most studies are about glioblastoma multiforme and malign melanoma.Most studies in literature have been done with extremely low frequency and pulsed electric fields. In terms of diseases, most studies are about glioblastoma and melanoma.

Vit-106 is a promising zirconium-based alloy with high glass-forming ability and belongs to the so-called bulk metallic glasses (BMG). Workpieces with a size of around one centimeter in all three dimensions can be obtained from a BMG alloy by casting. However, further increasing the cast size decreases the cooling rate and thus induces crystallization. Selective laser melting (SLM) is a well-known technique to overcome the size limitations for BMGs because a workpiece is built by the addition of multiple melt portions where the cooling rate is kept above the critical one. Currently, BMG parts obtained by SLM suffer from partial crystallization. The present work studies the influence of SLM process parameters on partial crystallization of Vit-106 by metallography and the influence of the microstructure on mechanical properties by microhardness and wear resistance testing. Submicron crystalline inclusions are observed in an amorphous matrix of Vit-106 alloy obtained by SLM. The size and the concentration of the inclusions can be controlled by varying the laser scanning speed. It is shown that submicron crystalline inclusions formed in the amorphous matrix during SLM can favorably affect microhardness and wear resistance.

Nerve agents have recently been used in battlefield operations, espionage wars and terrorist attacks. These compounds, like some pesticides, cause organophosphate poisoning. The rapid, non-contact detection of a sarin simulant has been demonstrated at the Diagnostics and Metrology Laboratory of the Italian National Agency for New Technologies, Energy and Sustainable Economic Development using laser photoacoustic spectroscopy, an infrared absorption technology. The first measurements, carried out with an experimental system based on a quantum cascade laser and developed for the assessment of food authenticity in the “fingerprint region”, show that a detection limit of 1 nanolitre is within the reach of the instrument when chemometric analysis is applied.

This article presents analysis of carbon Swan, C$_2$, laser-plasma emission records using line strength data, C$_2$-Swan-lsf, and the ExoMol astrophysical database. Line-strength data fitting of 0.25-nanometer spectral resolution ExoMol-computed spectra for a 6,000-Kelvin temperature C$_2$ Swan system, ${\rm d}\ ^3\,\Pi_{\rm g} \longrightarrow {\rm a} \ ^3\,\Pi_{\rm u}$, $\Delta {\rm v} = 0, \pm 1$, reveals a temperature of 5,640 Kelvin. The six per cent lower temperature is associated primarily with the accuracy of the transition wavelengths in the ExoMol vs. C$_2$-Swan-lsf data. The analysis of experiment data examines spectra that are recorded following laser-induced optical breakdown in carbon monoxide. The laser plasma data are recorded with 0.35-nm spectral resolution. The temperature inferences are elaborated when using non-linear fitting with both databases. The results show temperatures in excess of 6,000 Kelvin for the $\Delta {\rm v} = -1$ sequence, and for a time delay of 30\,$\upmu$s from laser plasma initiation. The accuracy of the C$_2$ Swan bands line strength data is of the order of 1 picometer. These line strength data are also utilized for analysis of laser-induced fluorescence experiments that employ a spectral resolution of 5.5 picometer, and a temperature of 2,716 Kelvin is inferred. Accurate C$_2$ databases show many applications in laboratory diagnosis and interpretation of astrophysical plasma records.

Laser Direct Writing (LDW), also known as 3D multi-photon laser lithography of resins, is a promising technique for fabricating complex free-form elements, including micro-optical functional components. Regular organic or hybrid (organic-inorganic) resins are often used, with latter exhibiting better optical characteristics, as well as having the option to be heat-treated into inorganic glass-like structures, particularly useful for resilient micro-optics. While this work is a continuation of SZ2080™ calcination development , the Laser-Induced Damage Threshold (LIDT) of such sol-gel-derived glass micro-structures, particularly those that undergo heat treatment, has not been well-characterized. In this pilot study, we investigated the LIDT using the Series-on-One (S-on-1) protocol of functional micro-lenses produced via LDW and subsequently calcinated. Our results demonstrate that the LIDT can be significantly increased, even multiple times, by this approach, thus enhancing the resilience and usefulness of these free-form micro-optics. This work represents the first investigation in terms of LIDT into the impact of calcination on LDW produced sol-gel-derived glass micro-structures, and provides important insights for the development of robust micro-optical devices.

The first detection of gypsum (CaSO4.2H2O) by the Mars Science Laboratory (MSL) rover Curiosity in the Gale Crater, Mars created a profound impact on planetary science and exploration. The unique capability of plasma spectroscopy involving in situ elemental analysis in extraterrestrial environments, suggesting the presence of water in the red planet based on phase characterization and providing a clue to Martian paleoclimate. The key to gypsum as an ideal paleoclimate proxy lies in its textural variants, and in this study terrestrial gypsum samples from varied locations and textural types have been analyzed by Laser Induced Breakdown Spectroscopy (LIBS) technique. Petrographic, sub-microscopic and powder X-ray diffraction characterizations confirm the presence of gypsum (hydrated calcium sulphate; CaSO4.2H2O), bassanite (semi-hydrated calcium sulphate; CaSO4.1/2H2O) and anhydrite (anhydrous calcium sulphate; CaSO4) along with accessory phases (quartz and jarosite). The principal component analysis of LIBS spectra from texturally varied gypsums can be differentiated from one another because of the chemical variability in their elemental concentrations. The concentration of gypsum is determined from the partial least-square regressions model. Rapid characterization of gypsum samples with LIBS is expected to work well in extraterrestrial environments.

Laser-plasma interactions of ultra-short laser pulses with solid targets can generate highly intense pulses of protons and ions with energies of several MeV. The spectra of these particles are spread over a wide range following a Maxwellian distribution. We report on the design and testing of a magnetic chicane for the selection of protons within a limited energy window. It consists in two successive, anti-parallel dipole fields generated by cost-effective, permanent C-magnets with customized configuration and longitudinal positions. The chicane has been implemented into the target vessel of a petawatt laser facility under constraints on the direction of the incoming laser beam and guidance of the outgoing particles through a vacuum port. The separation of protons and carbon ions within distinct energy intervals has been demonstrated and compared to a ray tracing code.

Purpose: To examine the effectiveness of patterned laser trabeculoplasty (PSLT) as an additional treatment for patients of open-angle glaucoma (OAG) receiving maximized ocular hypotensive medications (OHM). Methods: Forty eyes of 33 patients (average age 72.7±10.7 years) who had not previously undergone open glaucoma surgery or laser trabeculoplasty and were treated with maximized OHM between June 2018 and March 2022 were included. A 360-degree PSLT was conducted and postoperative intraocular pressure (IOP) and survival curves at 1, 3, 6, 9, and 12 months were evaluated. Results: According to the Kaplan-Meier survival analysis, the average survival time was 8.1 months with death defined as postoperative IOP reduction of less than 10% or requiring additional treatment. The average survival time was 4.9 months with death defined as postoperative IOP reduction of less than 20% or requiring additional treatment. In the 31 eyes which received no additional treatment after PSLT, the mean preoperative IOP was 18.5±3.9 mmHg, which reduced to 15.3±4.1 mmHg (p=1.62 x 10-6)), 15.5±3.4 mmHg (p=1.51 x 10-5), 15.7±4.0 mmHg (p=1.75 x 10-5), 14.7±4.38 (p=2.89 x 10-6), and 15.0±4.0 mmHg (p=5.74 x 10-9) at 1, 3, 6, 9 and 12 months after PSLT, respectively. The IOP reduction rate one year after PSLT was 18.7%. Thirteen of the 31 eyes (42%) achieved a 20% reduction in IOP compared to the baseline. Conclusion: Adjunctive treatment with PSLT in OAG patients receiving maximized OHM may be effective over 12-months of follow-up.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

Agriculture and rural regions in Europe face a number of economic, social and environmental challenges. Rural areas are active players in the EU’s green transitions. Weeding is one of the most important factors of agricultural production. New weeding techniques are being developed to enhance sustainability. Among them laser based weeding seems a promising alternative for use of chemicals. WeLASER technique is a novel technique of weed control. Its successful implementation depends on many factors related to the innovation itself, policy context, farming conditions and users’ attitudes. Survey was carried out to provide the insight on the attitudes toward the innova-tive (laser) weed control tool (device - autonomous robot). The CATI method was selected for the survey of farmers opinion and carried out in three countries: Denmark, Spain and Poland. Statistical methods were applied to analyze the results. The study provided knowledge on how farmers see the barriers and opportunities of implementing the device in practice. Positive attitudes of farmers were observed but with high expectations related to quality of the technique and systemic conditions of its implementation.

This paper describes design of experimental methodology developed to measure the working properties of accuracy of the path traversed by a collaborative robot. The methodology proposed here uses a collaborative robot and a laser measuring system Gepard from Raytec. The main parts of the measuring chain and the ISO 9283 standard are described. The proposed experimental methodology should examine working properties of industrial robots, such as the properties of position and path. The focus of this paper lies on the path accuracy of robots. Currently, the interest in this topic is on the rise and the measuring systems capable of recording this parameter are too costly. This paper focuses on experimental measuring of the path properties, describing them in more detail. The measuring and results were processed in the software tool developed for Gepard.

In mobile robotics, laser scanners have a wide spectrum of indoor and outdoor applications, both in structured and unstructured environments, due its accuracy and precision. Most works that use this sensor have their own data representation and their own case-specific modeling strategies, and no common formalism is adopted. To address this issue, this manuscript presents an analytical approach for identification and localization of objects using a 2D LiDARs Our main contribution lies in formally defining laser sensor measurements and their representation, the identification of objects, their main properties and their location in a scene. We validate our proposal with experiments in generic semi-structured environments common in autonomous navigation, and we demonstrate its feasibility on multiple object detection and identification, following strictly its analytical representation. Finally, our proposal further encourages and facilitates the design, modeling and implementation of other applications that use laser scanners as a distance sensor.

We report a simple and high-performance flexible strain sensor based on liquid metal nanoparticles (LMNPs) on polyimide substrate by laser induced deposition. The LMNPs were prepared by ultrasonic method, and then the femtosecond laser direct writing technology was used to induce the assembly and deposition of the LMNPs to form liquid metal microwires. Laser local sintering enhances the connection between particles, and a wearable strain sensor was fabricated with the high sensitivity as high as 76.18, the good linearity (a correlation coefficient of 0.999) in a wide sensing rage, the fast response/recovery time of 159 ms/120 ms. Attributed to these extraordinary strain sensing performances, the sensor can sense various dynamic strains in real time, monitor both subtle physiological activities and large human motions. It can be adhered to human skin, and well reflect the change of facial expression and realize real-time monitoring of facial expression. And the vocal cord vibration can be detected for speech recognition while the sensor attached to the outside of the throat.

Axions can be stimulated to decay to photons by ambient photons of the right frequency or by photons from decay of neighboring axions. If the axion density is high enough the photon intensity can be amplified, which is a type of lasing or an axion maser. Here we review the astrophysical situations where axion lasing can appear and possibly be detected.

Fused silica glass is a material with outstanding mechanical, thermal and optical properties. Being a brittle material, it is challenging to shape. In the last decade, the manufacturing of monolithic flexible mechanisms in fused silica has evolved with the femtosecond laser-assisted etching process. However, instrumenting those structures is demanding. To address this obstacle, this article proposes to inscribe a Bragg Grating sensor inside a flexure and interface it with an optical fibre to record the strain using a spectrum analyzer. The strain sensitivity of this Bragg Grating sensor is characterized at 1.2 pm/μϵ (1 μϵ = 1 microstrain). Among other applications, deformation sensing can be used to record a force. Its use as a micro-force sensor is estimated. The sensor resolution is limited by our recording equipment to 30 μN over a measurement range above 10 mN. This technology can offer opportunities for surgery applications or others where precision and stability in harsh environments are required.

Selective laser sintering (SLS) has drawn attention for the fabrication of three-dimensional oral dosage forms due to the plurality of drug formulations that can be processed. The aim of this work was to employ SLS with a CO2 laser for the manufacturing of carvedilol personalised dos-age forms of various strengths. Carvedilol (CVD) and vinylpyrrolidone-vinyl acetate copolymer (Kollidon VA64) blends of various ratios were sintered to produce CVD tablets of 3.125, 6.25 and 12.5 mg. The tuning of the SLS processing parameter laser intensity, improved printability and impacted the tablet hardness, friability, CVD dissolution rate, and the total amount of drug re-leased. Physicochemical characterization showed the presence of CVD in the amorphous state. X-ray micro-CT analysis demonstrated that the applied CO2 intensity affected the total tablet po-rosity, which was reduced with increased laser intensity. The study demonstrated that SLS is a suitable technology for the development of personalised medicines that meet the required specifications and patient needs.

The dynamics of the topological charge of a vortex optical beam propagating in a turbulent air with accounting for the cubic nonlinearity is theoretically considered. On a number of examples, we show that the optical beam self-focusing manifests itself ambiguously depending on optical wave power. At near-critical values of beam power, self-focusing leads to enhanced spatial localization of optical vortices and substantial suppression of vortex walk-off relative to the beam axis caused by air turbulence. However, with increasing of optical intensity the modulation instability imposed by cubic nonlinearity becomes significant and contributes jointly with medium turbulence to faster divergence of vortex beams.

Crystallization often occurs in the laser welding of amorphous alloys, reducing the amorphous alloys’ properties. So, it is necessary to simulate the temperature field curve of the welding area by computer and then determine the power and laser moving speed of laser welding. In this paper, the temperature field curve of Zr41.2Ti13.8Cu12.5Ni10Be22.5(Vit1) amorphous alloy in laser welding is obtained by finite element analysis. The continuous heating curve (CHT) of Vit1 is fitted by the Vogel-Fulcher-Tammann (VFT) equation and the Kissinger equation. If the temperature field curve intersects with the CHT curve, crystallization occurs. The experiment results show that the VFT equation can be used to predict the crystallization of Vit1 better in laser welding. The tem-perature and welding time are increased by using low welding speed. Therefore, the temperature of the weld zone cannot fall in time, resulting intersection of the temperature field curve and the CHT curve. So, crystallization can be avoided if the welding speed is controlled within a rea-sonable range, and the highest temperature is kept under the CHT curve.

Controlled deposition of CoCrFeNiMo0.2 high entropy alloy (HEA) micro-particles was achieved using laser induced forward transfer (LIFT). Ultra-short laser pulses, 230 fs of 515 nm wavelength, were tightly focused into ∼ 2.4 μm focal spots on the ∼50 nm thick plasma-sputtered films of CoCrFeNiMo0.2. The HTA films were transferred onto glass substrates by magnetron sputtering in vacuum (10−8 atm) from the thermal spray coated substrates. The absorption coefficient of CoCrFeNiMo0.2 α ≈ 6 × 105 cm−1 was determined at 600 nm wavelength. The real and imaginary parts of refractive index (n + iκ) of HEA were determined from reflectance and transmittance using nano-films.

Adaption of laser communication terminals to airborne and lean-satellite platforms is now a vogue, made possible due to the progressing advancements in lightweight components and compactness of onboard electro-optical transceivers and control systems. This enables highly secured and superior data-transmission rates beyond multiple Gigabit/second on CubeSats and drones compared to Megabit/second rates offered by similar radio-transceivers form factors. However, laser-transmission links require a very stringent beam-pointing stability because they are easily perturbed by attitude variations and micro-vibrations generated by the host platform’s propulsion system or other mechanically active subsystems in proximity with the transmitter’s optical head. Severe line-of-sight jitter causes the downlink laser beam to drift from the targeted receiving system’s field-of-view, inducing pointing errors, increasing signal outage probability and information loss. We experimentally examine the platform jitter generated by the propellers of an hexacopter drone during ground operation and the attitude-control unit’s reaction wheels in a 6U CubeSat structure. We determined the vibration spectrum unique to these platforms and accordingly prescribe requirements for applicable optical fine pointing and disturbance isolation or suppression systems needed to achieve a high-fidelity laser-communication link.

Two types of trenches cross-section in conventional vertical and brand new reverse-V-shape have fabricated on SCD substrate by micro-jet water-assist laser, the epitaxial lateral overgrowth technique has applied by microwave plasma chemical vapor deposition system in forming multiple micrometer-size channels. Raman and SEM techniques have applied in analyze both types growth layer characterization. Optical microscope has used to test microchannels hollowness. As a result, with the brand new reverse-V-shape trench, epitaxial lateral overgrowth layer reaches higher SCD surface morphology and crystal quality.

Compared with liquid crystal clad waveguide, MEMS mirror has some merits, such as high-er-transmissivity, lager-angle of scanning, faster scanning speed and so on. Furthermore, MEMS mirror arrays perform more superior than MEMS mirror when they steer laser beam, which make MEMS arrays much more suitable to be used in devising compact Lidar. Before assembling a Lidar with MEMS arrays, the optical intensity and distributions of the laser diffracted by MEMS arrays should be analyzed, but few published papers about this issue are available so far, this paper will focus on this issue about MEMS arrays. Firstly, the complex amplitudes of laser which is diffracted by 1-D and 2-D arrays are presented, respectively. Then the optical intensity and distributions on the observation plane are presented. Finally, the simulation diagrams of these distributions are shown, and the correctness of the results is indirectly verified by Young’s dou-ble-slit experiment. The results gotten in this letter are essential to design a compacted Lidar based on MEMS arrays.

(1) Background: Prefabricated zirconia crowns are used to restore teeth in children. The purpose of this study was to evaluate the removal of these crowns with the erbium, chromium: yttrium-scandium-gallium-garnet (Er,Cr:YSGG) laser; (2) Methods: Twelve primary and 13 permanent teeth were prepared and prefabricated zirconia crowns were passively fitted and cemented with two resin modified glass-ionomer cements. Surface areas of prepared teeth and crowns were calculated. Crowns were removed using two laser settings: 4.5 Watts, 15 Hertz, 20 water/ 20 air, and 5 Watts, 15 Hertz, 50 water/50 air. The retrieval time and temperature changes were tested recorded. Data were analyzed using ANOVA with Tuckey’s adjusted post hoc pairwise comparison t-test; (3) Results: The average time for crown removal was: 3 minutes, 47.7 seconds for permanent; and 2 minutes 5 seconds for primary teeth. The mean temperature changes were 2.48℃ (SD=1.43) for permanent; and 3.14℃ (SD=1.88) for primary teeth. The time to debond was significantly positively correlated with tooth inner surface area and volume, outer crown volume, and the cement volume; (4) Conclusions: Use of the Er,Cr:YSGG laser is an effective, safe and non-invasive method to remove prefabricated zirconia crowns cemented with RMGI cements from permanent and primary teeth.

Refractive surgery is an increasingly popular procedure to decrease spectacle or contact lens dependency. The two most commonly used surgical techniques to correct myopia is Photorefractive keratectomy (PRK) and Femtosecond- Lasik (FS-LASIK)There are few publications that gathers such a long term follow up of both surgical techniques (2) Methods It has been performed a retrospective non-randomized study 509 PRK eyes and 310 FS-LASIK surgeries were followed for 10 years for the treatment of myopia and compound myopic astigmatism. Patients were followed up three months, one year, 2 years, 5 and 10 years. The safety index of both procedures was defined as a quotient between the postoperative BCVA (Best Corrected Visual Acuity) and the preoperative BCVA. The predictability is calculated as difference between the expected spherical equivalent and the achieved spherical equivalent. The efficacy index was calculated as a quotient between postoperative UCVA divided by the preoperative BCVA (3) Results. The results were: a safety index higher than 100% (109%) and an efficacy index of 82.4% after 10 years of PRK surgery in both groups. FS-LASIK was the safest surgery after 10 years and the most efficacy technique although in this case there were no statistically significant differences (4) Conclusions. All these data demonstrated better indexes for FS-LASIK

The effects of build orientation and heat treatment on the crack growth behavior of 316L stainless steel (SS) fabricated via a selective laser melting (SLM) additive manufacturing process were investigated. Significant growth of available research results of additively manufactured metallic parts still needs to be improved. The most important issue connected with properties after additive manufacturing is properties high anisotropy, especially from the fatigue point of view. The research included crack growth behavior of additively manufactured 316L in comparison to conventionally made reference material. Both groups of samples were obtained using precipitation heat treatment. Different build orientation in additively manufactured samples and rolling direction in reference samples were taken into account as well. Precipitation heat treatment of additively manufactured parts allowed to reach similar microstructure and tensile properties to elements conventionally made. The heat treatment positively affected fatigue properties. Additionally, precipitation heat treatment of additively manufactured elements significantly affected the reduction of fatigue cracking velocity and changed the fatigue cracking mechanism.

Low-loss photonic waveguides in lithium niobate offer versatile functionality as nonlinear frequency converters, switches, and modulators for integrated optics. Combining the flexibility of laser processing with liquid phase epitaxy we have fabricated and characterized lithium niobate channel waveguides on lithium niobate and lithium tantalate. We used liquid phase epitaxy with K2O flux on laser-machined lithium niobate and lithium tantalate substrates. The laser-driven rapid-prototyping technique can be programmed to give machined features of various sizes, and liquid phase epitaxy produces high quality single-crystal, lithium niobate channels. The surface roughness of the lithium niobate channels on a lithium tantalate substrate was measured to be 90 nm. The lithium niobate channel waveguides exhibit propagation losses of 0.26 ± 0.04 dB/mm at a wavelength of 633 nm. Second harmonic generation at 980 nm was demonstrated using the channel waveguides, indicating that these waveguides retain their nonlinear optical properties.

The paper is focused on the examination of the internal quality of joints created in a multi-material - additive manufacturing process. The main part of the work focuses on experimental production and non-destructive testing of restrained joints of modified PLA (polylactic acid) and ABS (Acrylonitrile butadiene styrene) 3Dprinted on RepRap 3D device that works on the "open source" principle. The article presents the outcomes of non-destructive materials test in the form of the data from the Laser Amplified Ultrasonography, microscopic observations of the joints area and tensile tests of the specially designed samples. The samples with designed joints were additively manufactured of two materials: specially blended PLA (Market name – PLA Tough) and conventionally made ABS. The tests are mainly focused on the determination of the quality of material connection in the joints area. Based on the results obtained, the samples made of two materials were compared in the end to establish which produced material joint is stronger and have a lower amount of defects.

Tengchongite is a uranyl molybdate uranium mineral and it was found and named by Chen 1985.No more scholars studied on tengchongite after Chen’s work, The identification of this mineral has only been confirmed by single crystal X-ray diffraction. In the paper, micro laser Raman spectroscopy and infrared spectroscopy are used to identify the spectroscopy properties of tengchongite. The studies fill in the gaps of more than 30 years in terms of the molecular spectroscopy research of tengchongite. The mineral has an ideal model of Ca(UO₂)₆(MoO₄)₂O₅•12H₂O its bands attributed to the vibrating units are clearly identified in the Raman spectrum. Symmetric stretching modes at 812 cm^-1 and 839 cm^-1 are assigned to ν1 (UO₂)²⁺ ,The ν3 antisymmetric stretching modes of (UO₂)²⁺ are observed at 896 cm^-1, Symmetric stretching modes at 419^-1 and 440 cm^-1 are assigned to ν2 (UO₂)²⁺ .Symmetric stretching modes at 919cm-1 are assigned to ν1(MoO₄)^2-,The ν3 antisymmetric stretching modes of (MoO₄)^2- are observed at 752 cm^-1, the in-plane ν2(MoO₄)^2-and the out-of-plane ν4(MoO₄)^2- bending modes are at 169 cm^-1 and 254 cm^-1. IR spectrum of tengchongite shows the major uranyl band at 858 cm^-1 and 693 cm^-1, Mo-O bonds are observed at about 985 cm^-1 and 780 cm^-1, and H₂O groups are present with a wide range peaks from 3100 cm^-1 to 3500 cm^-1 and 1647 cm^-1, and the band at 1432.4 cm^-1 is probably due to the stretching vibration hydroxyl (OH^-1), therefore, tengchongite contains may include hydroxyl and its chemical formula needs to be modified .

We propose a concept of hybrid nanoelectronic-magnetic device for logic integrated platforms made of magnetic core-shell nanoparticles deposited onto prepatterned Si (111) substrate with basic logic circuitry made of metallic conductive lines. The synthesis of magnetic material and the creation of nanoelectronic prepatterned interdigitated die is reported and its capabilities are demonstrated in terms of magnetotransport properties. The laser pyrolysis method is employed in order to synthesize magnetic core-shell Fe / FeC nanoparticles with sizes between 12 – 15 nm. E-beam lithography has been used in order to design and execute two different layouts of interdigitated die, prepatterned with logic capacity, one with two pads and 50 microns thick conductive metallic lines, another one with 4 pads and parallel 5 microns thick conductive lines separated by 5 microns thick spacer. The as-obtained structures are morphologically characterized by means of optical, scanning and transmission electron microscopies. As-synthesized core-shell nanoparticles have been magnetically characterized inasmuch as the hybrid device obtained by depositing centrifugated and dispersed core-shell nanoparticles from liquid carrier solutions. For the first time, a significant giant magnetoresistive (GMR) effect has been observed and measured for the hybrid architectured device made of Fe / FeC nanosized materials on pre-patterned interdigitated die. A ∆R/R of 8% at 4.2 K has been measured from conductivity-in-plane electron transport measurements. This opens possibilities for the use of such devices as arrays of nanosensors and in spintronic applications.

Three-dimensional (3D) printing has allowed for production of geometrically complex 3D objects with extreme flexibility, which is currently undergoing rapid expansions in terms of materials, functionalities, as well as areas of application. When attempting to print 3D microstructures in glass, femtosecond laser induced chemical etching (FLICE) – which is a subtractive 3D printing technique – has proved itself a powerful approach. Here, we demonstrate fabrication of macro-scale 3D glass objects of large heights up to ~3.8 cm with an identical lateral and longitudinal spatial resolution of ~20 μm. The remarkable accomplishment is achieved by revealing an unexplored regime in the interaction of ultrafast laser pulses with fused silica which results in aberration-free focusing of the laser pulses deeply inside fused silica.

This paper describes a multi-channel in-situ monitoring system developed to better understand defect formation signatures in metal additive manufacturing. Three high-speed imaging modes coupled with an image computer capable of processing and storing these data streams allowed an examination of defect formations signatures and mechanisms. It was found that defects later detected in X-ray computed tomography (CT) scans were related to regions with anomalous heat signatures and powder bed morphology. Automated defect detection algorithms based on these defect signatures captured 80% of defects greater than 300 µm.

Micro Injection molding combined with the use of removable inserts is one of the most promising manufacturing process for microfluidic devices, such as Lab-on-a-chip, that have the potential to revolutionize the healthcare and diagnosis system. In this work we have designed, fabricated and tested a compact and disposable plastic optical stretcher. To produce the mould inserts, two micro manufacturing technologies have been used. Micro Electro Discharge machining was used to reproduce the inverse of the capillary tube connection characterized by high aspect ratio. Thanks to the high accuracy of femtosecond laser machining, instead, we manufactured insert with perfectly aligned microfluidic channels and fiber slots, facilitating the final composition of the optical manipulation device. The optical stretcher operation is tested using microbeads and red blood cells solutions. The prototype presented in this work demonstrates the feasibility of this approach that should guarantee a real mass production of ready-to-use- Lab-on-a-chip.

The application of solvent method in the preparation of polypropylene powders was investigated, including the influence of various technological conditions, such as the raw material melt index of polypropylene, processing temperature, dosage of the solvent and the packing pressure. The experimental data show that using solvent method can effectively produce polypropylene powder, and the optimal technological conditions are: melt index of polypropylene being about 17.8 g/10min, processing temperature being about 166.0 ℃, dosage of the solvent being about 0.067g/ml and the packing pressure being about 0.7MPa.Under this technological conditions, polypropylene powder with excellent sphericity could be prepared, the apparent density of powder can reach 0.40 g/cm3 and the prepared powder displayed a narrow size distribution with the mean size of about 42.7 µm.

In biology molecules and macromolecules like sugars, proteins, DNA, and RNA are of utter importance. Detecting their presence as well as their conformation is still a challenge in many cases. It is well known that the vibrational states of such molecules lie from the infrared to the TeraHertz range. Spectroscopy can be used to detect such compounds and probe their conformation. Still, terahertz spectroscopy on biosample is a challenge for two main reasons: water absorption; and the small size of the samples. The sample volume is smaller than the cube of the TeraHertz wavelength; the light matter interactions are thus extremely reduced. In this paper, we present the design, fabrication, characterization and the first typical uses of a biophotonic device aiming at increasing light matter interaction to enable terahertz spectroscopy of minute samples on a broad band (0.2–2 THz). We demonstrate time domain spectroscopy experiments on few µl samples showing the validity of our approach.

This article presents a methodology to process information from a Terrestrial Laser Scanner (TLS) from three dimensions (3D) to two dimensions (2D), and to two dimensions with a color value (2.5D), as a tool to document and analyze heritage buildings. Principally focused on the loss of material in stone, this study aims at creating an evaluation method for loss control, taking into account the state of conservation of the building in terms of restoration, from studying the pathologies, to their identification and delimitation. A case study on the Cathedral of the Seu Vella de Lleida was completed, examining the details of the stone surfaces. This cathedral was affected by military use, periods of abandonment, and periodic restorations.

The interest in random fiber lasers (RFLs), first demonstrated one decade ago, is still growing and their basic characteristics have been studied by several authors. RFLs are open systems that present instabilities in the intensity fluctuations due to the energy exchange among their non-orthogonal quasi-modes. In this work, we present a review of the recent investigations on the output characteristics of a continuous-wave erbium-doped RFL, with emphasis on the statistical behavior of the emitted intensity fluctuations. A progression from the Gaussian to Lévy and back to the Gaussian statistical regime was observed by increasing the excitation laser power from below to above the RFL threshold. By analyzing the RFL output intensity fluctuations, the probability density function of emission intensities was determined, and its correspondence with the experimental results was identified, enabling a clear demonstration of the analogy between the RFL phenomenon and the spin-glass phase transition. A replica-symmetry-breaking phase above the RFL threshold was characterized and the glassy behavior of the emitted light was established. We also discuss perspectives for future investigations on RFL systems.

This work presents results of property researches of fabricated samples of silica few-mode optical fiber (FMF) with induced chirality under twisting 10 and 66 revolutions per meter, core diameter 11 µm, typical “telecommunication” cladding diameter 125 µm and improved height of quasi-step refractive index profile. Proposed FMF supports 4 guided modes over “C”-band. We represent results of computed characteristics, as well as experimentally measured spectral responses of laser-excited optical signals, including researches and analysis of few-mode effects, occurring after fiber Bragg grating writing.

This work discusses laboratory measurements of atomic and diatomic molecular species in laser-plasma generated in gases. Noticeable self-absorption of the Balmer series hydrogen alpha line occurs for electron densities of the order of one tenth of standard ambient temperature and pressure density. Emission spectra of selected diatomic molecules in air or specific gaseous mixtures at or near atmospheric pressure reveal minimal plasma re-absorption. Abel inversion of the plasma in selected gases and gas mixtures confirm expansion dynamics that unravel regions of atomic and molecular species of different electron temperature and density. Time resolved spectroscopy diagnoses self-absorption of hydrogen alpha and hydrogen beta lines in ultra-high pure hydrogen gas. Radiation from a Nd:YAG laser device induces micro-plasma for pulse widths in the range of 6 ns to 14 ns, energies in the range of 100 mJ to 800 mJ, and for peak irradiance of the order 1 to 10 TW/cm². Atomic line profiles yield electron density and temperature from fitting of line profiles to wavelength and sensitivity corrected spectral radiance data. Analysis of measured diatomic emission data yields excitation temperature of primarily molecular recombination spectra. Applications of the laboratory experiments extend to investigations of stellar astrophysics white dwarf spectra.

A paper impregnated with silver nanoparticles (AgNPs) has been prepared. For the preparation of the substrates, aqueous suspensions of pulp fines, a side product from the paper production, have been mixed with Ag nanoparticles (AgNP) suspensions. The nanoparticle synthesis thereof was carried out via laser ablation of pure Ag in water. After the sheet formation process, the leaching of the AgNPs was determined to be low while the sheets exhibited antimicrobial activity towards E. Coli.

(1) Background: Double-strand breaks (DSBs) in a single nucleus are usually measured using the sperm chromatin structure assay (SCSA), sperm chromatin dispersion (SCD) test, and comet assay (CA). We developed mono-dimensional single-cell pulsed-field gel electrophoresis (1D-SCPFGE) and angle-modulated two-dimensional single-cell pulsed-field gel electrophoresis (2D-SCPFGE) to observe DNA fragmentation in separated motile sperm. (2) Methods: We set up comparative standards, calibration curves, the required sensitivity, and eligibility criteria for test sperm to validate their measurement principles. (3) Results: We revealed that the conventional methods overlooked the interference of nucleoproteins in their measurements. In-gel proteolysis improves the measurement accuracies of 1D- and 2D-SCPFGE. We recommend using naked DNA for comparative standards and test specimens. Moreover, we have observed several dysfunctions that may induce DNA damage in the separated motile sperm. Overall, our discussion highlights the need to revisit the conventional univariable analyses based on the SCSA, SCD test, and CA. (4) Conclusions: Human infertility is a complex syndrome, and the aim of quality control in intracytoplasmic sperm injection is to identify the underlying dysfunctions remaining in the separated motile sperm that render them ineligible for injection. Well-designed, multivariable analyses with special consideration to confounding factors are necessary in future cohort studies.

The optical properties of the Nafion polymer membrane containing colloidal CdSe/CdS/ZnS nanocrystals embedded by diffusion have been studied. The CdSe/CdS/ZnS nanocrystals have a core/shell/shell appearance. A toluene solution was used to provide mobility of the active sul-fone groups of the Nafion membrane and to embed the nanocrystals inside the membrane. The kinetics of the process of nanocrystal embedding into the membrane matrix was studied using luminescence analysis, absorption spectroscopy and laser emission spectroscopy techniques. The diffusion of colloidal CdSe/CdS/ZnS nanocrystals into the Nafion proton exchange membrane resulted in a new molecular complex «Nafion-colloidal CdSe/CdS/ZnS nanocrystals». The pres-ence of new luminescence centers based on CdSe/CdS/ZnS nanocrystals in the membrane was registered using laser emission spectroscopy. Colloidal nanocrystals located in the Nafion ma-trix represent an analogue of a luminescent transducer. The lines contained in the luminescence spectrum of the membrane, which has been in solution with colloidal nanocrystals for a long time, registered upon its drying, show the kinetics of the formation of the molecular complex «Nafion membrane - nanocrystals». The luminescence spectrum of the membrane with nano-crystals contains additional intensity maxima that do not coincide with the spectral lines of the solvent and Nafion membrane. The intensity of the luminescence spectrum of the membrane with embedded nanocrystals is higher than the intensity of the secondary emission peak of the initial nanocrystals, which is important for the practical use of the complex «Nafion-colloidal nanocrystals» in optical systems.

Urinary tract stones can obstruct the urinary tract, resulting in severe lower back pain, blood in the urine, vomiting, and painful urination. While small stones can pass naturally through the urine stream, larger ones necessitate fragmentation with shock wave lithotripsy (SWL) or laser ureteroscopy (URS) to prevent urinary tract blockage. A smart computer program was developed to predict treatment efficacy for removing a stone and potential complications for individual patients based on factors such as age, health conditions, stone details, and treatment instruments, ultimately recommending the most suitable option. Here, I present three case studies and their predicted outcomes. The program is available at: http://peteranoble.com/webapps.html

The electric vehicle (EV) industry challenges battery joining technologies by requiring higher energy density both by mass and volume. Improving the energy density via new battery chemistry would be the holy grail but is seriously hindered and progresses slowly. In the meantime, alternative ways, such as implementing more efficient cell packaging by minimizing the electrical resistance of joints are of primary focus. In this paper we discuss the challenges associated with the electrical characterisation of laser soldered joints in general, and the minimization of their resistive losses, in particular. In order to assess the impact of the joint resistance on the overall resistance of the sample, the alteration in resistance was monitored as a function of voltage probe distance and modelled by finite element simulation. The experimental measurements showed two different regimes: one far from of the joint area and another in its vicinity and within the joints cross section. The presented results confirm the importance of the thickness of the filler material, the effective and the total soldered area, and the area and the position of the voids within the total soldered area in determining the electrical resistance of joints.

The refractive index of a liquid serves as a fundamental parameter reflecting its composition, thereby enabling the determination of component concentrations in various fields such as chemical research, food industry, and environmental monitoring. Traditional methods for refractive index (RI) measurement rely on light deflection angles at interfaces between the liquid and a material of known refractive index. In this paper, the authors present a new differential refractometer for highly sensitive measurement of RI differences between two liquid samples. Using a configuration with two cells equipped with flat parallel plates as measuring elements, the instrument facilitates accurate analysis. Namely, the sensor signals from both the solution and the solvent cuvette are generated simultaneously with one laser pulse, reducing the possible fluctuations of the laser radiation intensity. Our evaluation shows the high sensitivity of RI measurements (< 7 · 106), so this differential refractometer can be proposed not only as a high-sensitivity sensing tool that can be used for mobile detection of nanoparticles in solution samples, but also to determine the level of environmental nano-pollution using water (including rain, snow) samples from various natural as well as industrial sources, thus helping to solve some important environmental problems.

The paper presents the results of high precision control survey carried out in the underground mining of Oyu Tolgoi project using terrestrial laser scanning technology. The purpose of the measurements is to ensure the heading, total length and volume of the penetration and excavation works are being implementing in accordance with the planned and designed dimensions. We established a network of 18 reference points in the tunnel of the selected underground level which were repeatedly measured 4 times by two round readings of the Trimble S7 tacheometry and processed by using the Trimble Business Center software. All points except the one was within the permissible error. Based on these points the excavation length and volumes were determined using the Trimble SX12 laser scanner. The difference between the planned work quantity provided by the Oyu Tolgoi project and the actual values measured by the laser scanning was calculated using the comparative method. The TLS partial control measurements in the excavations made through the ore bodies revealed the length of 20285.72 m and volume of 441128.80 m3 for underground 7 mine levels while their project values were 16158.26 m length and 422837.50 m3 volume, respectively.

Foot pain related to the plantar fascia is common in adults regardless of athletic background. Many pathologies can lead to the diagnosis of plantar enthesopathy, but the most relevant to this case study is related to structural defects within the plantar fascia. Due to the variety and sometimes unclear etiology of plantar fasciosis, no single standard of care treatment protocol is recognized. Often, patients receive NSAIDs, night splints, taping, physical therapy, foot orthosis, and extracorporeal shock wave therapies. This study presents Wharton Jelly (WJ) tissue allografts as an additional intervention for patients who fail standard-care treatments. WJ allografts are applied to supplement connective tissue defects directly, unlike other therapies, which aim to reduce swelling and symptomatic pain. This retrospective study includes seven patients who have previously failed standard-of-care treatment. Each received extracorporeal pulse-activated therapy (EPAT), WJ, laser therapy, and an orthotic. Patient progress was tracked using a visual analog scale, 0-10 scoring, reported by the patient at the initial visit and approximately thirteen weeks following, reporting an average improvement of 50%. The study's limitations include a small cohort size and a non-blinded retrospective design. These promising results provide evidence for a more extensive, randomized study to define dosage protocols further and confirm safety and efficacy.

Background: Laser therapies can cause hyper- and hypopigmentation of the skin. There is little evidence in the literature of effective treatments for these types of problems in Fitzpatrick IV-VI skin phototypes. The main aim of this retrospective study is to evaluate the effects of a new therapy combining the application of electromagnetic fields and vacuum on a subject with Fitzpatrick VI skin phototype, presenting an extensive, laser-induced facial dyschromia. The secondary aim is to test the effectiveness of a free imaging software for assessing skin pigmentation. Methods: The level of improvement after the therapy was evaluated, with a 5-point Likert scale, one month after the end of the treatment by both the subject, and the doctor who performed the treatment, and by two blinded dermatologists. With the free software, a three-dimensional reconstruction of the area treated and the evaluation of colour distribution were performed. Results: Both the subject and the doctors involved in the study positively evaluated the effects of the treatment. The image analysis highlighted the homogenization of the skin colour in the treated area. Conclusions: The combination of electromagnetic fields and vacuum for dyschromia treatments appears promising. The new method of assessing melanin levels resulted particularly efficient.

Emerging applications of optical technologies are driving the development of miniaturised light sources, which in turn require the fabrication of matching micro-optical elements with sub-1 mm cross sections and high optical quality. This is particularly challenging for spatially-constrained biomedical applications where reduced dimensionality is required, such as endoscopy, optogenetics, or optical implants. Planarisation of a lens by the Fresnel lens approach was adapted for a conical lens (axicon) and was made by direct femtosecond 780 nm/100 fs laser writing in SZ2080™polymer with photo-initiator. Optical characterisation of the positive and negative fraxicons is presented. Numerical modeling of fraxicon optical performance under illumination by incoherent and spatially extended light sources is compared with the ideal case of plane wave illumination. Considering the potential for rapid replication in soft polymers and resists, this approach holds great promise for the most demanding technological applications.

Antimicrobial photodynamic therapy (aPDT) used to sterilize carious dentin may irritate the pulp tissues because of tissue-penetrating laser and singlet oxygen generation. This study aimed to assess the effects of aPDT on rat pulp tissues. A cavity formed in a rat maxillary first molar was treated with aPDT. The combined photosensitizer and laser irradiation conditions in the aPDT groups were as follows: methylene blue and 100 mW for 60 s, brilliant blue (BB) and 100 mW for 60 s, BB and 50 mW for 120 s, and BB and 200 mW for 30 s. Each cavity was treated with an all-in-one adhesive and filled with flowable resin. aPDT was not applied for the control. In each group, the rats were sacrificed on postoperative days 1 and 14, and thin sections of the treated teeth were prepared. Pulp tissue disorganization (PTD), inflammatory cell infiltration (ICI), and tertiary dentin formation (TDF) were evaluated. At 1 day evaluation, there were significant differences between the aPDT group and controls with respect to PTD and ICI. 14 days later, almost all specimens showed tertiary dentin formation. aPDT caused temporarily reversible injury to the rat dental pulp, which healed with tertiary dentin formation.

Nondipole terms in the atom-laser interaction arising due to the presence of a magnetic component in an electromagnetic wave and its inhomogeneity lead to nonseparability of the center-of-mass (CM) and electron variables in the neutral atom and, as a consequence, to its acceleration. We investigate this effect as well as the accompanying excitation and ionization processes for the hydrogen atom in strong (1012 - 2×1014 W/cm2) linearly polarized short-wavelength (5eV ≲ℏω≲ 27 eV) electromagnetic pulses of about 8 fs duration. The study has been carried out within the framework of a hybrid quantum-quasiclassical approach in which the coupled time-dependent Schrödinger equation for an electron and the classical Hamilton equations for the CM of an atom are simultaneously integrated. Optimal conditions with respect to the frequency and intensity of the electromagnetic wave for the acceleration of atoms without their noticeable ionization are found in the analyzed region.

The mechanical properties, structure, and morphology of milled and 3D printed Ti-6Al-4V alloys produced by selective laser melting were investigated in this study. The mechanical properties were investigated by means of nanoindentation, a tensile test, and a three-point bending test. The Atomic Force Microscope (AFM) was used to study the surface topography and roughness of both titanium alloys. The surface structure and phase analysis were studied by a scanning electron microscope (SEM) and through powder X-ray diffraction (XRD). The results from the nanoindentation experiments showed that the 3D-printed sample has higher indentation hardness and modulus than the milled one. The AFM observation of the surface topography of the samples showed that the milled sample has a higher roughness than the 3D-printed one. The tensile test results showed that the 3D printed sample by means of Selective Laser Melting (SLM) technology has about 26% higher tensile strength and smaller elongation than the milled one. The 3-point bending test revealed that the 3D printed Ti-6Al-4V sample has higher flexural strength than the milled one. It was found that the 3D-printed sample has a smaller crystal size than the milled one, which, according to the Hall-Petch relationship, leads to its higher indentation hardness.

Damaged connective tissues between the bone and tendons or ligaments are common among adults regardless of activity level. Achilles tendinosis is one of the most common tissue defects and enthesopathies. The patient in this study is a 54-year-old female with chronic Achilles tendinosis from chronic enthesopathy at the Achilles tendon insertion with a retrocalcaneal exostosis for three years who has failed standard-of-care practices for over two years. The patient received extracorporeal pulsed-activated therapy (EPAT) before applying 2ml of CryoText, a Wharton’s jelly tissue allograft. The patient then received class IV laser therapy treatments twice weekly for three weeks. The patient started with a 10/10 VAS at the initial visit. At five weeks post-application, the patient’s score had improved by 80% at 2/10 VAS. By week 13, the patient rated her pain as 0/10 VAS. The improvement in patient-reported pain and functionality reported in this study after the application of Wharton’s Jelly, EPAT, and class IV laser therapy warrants future research studying the safety and efficacy of these patient care modalities together.

Speckle Plethysmography (SPG) and Photoplethysmography (PPG) are different biophotonics technologies that allow for measurement of hemodynamics. As the difference between SPG and PPG under low perfusion conditions is not fully understood, a Cold Pressor Test (CPT) was used to modulate blood pressure and peripheral circulation. A custom-built setup simultaneously derived SPG and PPG from the same video streams at two wavelengths (639 nm and 850 nm). SPG and PPG were measured at right index finger location before and during CPT using finger Arterial Pressure (fiAP) as reference. The effect of CPT on Alternating Component amplitude (AC) and Signal-to-Noise-Ratio (SNR) of dual-wavelength SPG and PPG signals was analysed across participants. Furthermore, waveform differences between SPG, PPG, and fiAP based on frequency harmonic ratios, were analysed for each subject (n=10). Both PPG and SPG at 850 nm show a significant reduction during CPT for both AC and SNR. However, SPG showed significantly higher and more stable SNR than PPG in both study phases. Harmonic ratios were found substantially higher in SPG than PPG. Therefore, in low perfusion conditions, SPG seems to offer a more robust pulse wave monitoring with higher harmonic ratios than PPG.

The pulse duration in short-pulse schemes for Self-Amplified Spontaneous Emission Free Electron Lasers (SASE FELs) is limited by the FEL coherence time. A recently proposed concept allows to overcome the coherence time barrier and to get much shorter pulses. When the lasing part of an electron bunch is much shorter than the coherence time, one can suppress the radiation in the long main undulator while preserving microbunching within that short lasing slice. Then a short radiation pulse is produced in a relatively short radiator. A possible suppression method, an excessive reverse undulator taper, is discussed and illustrated numerically in this paper. We also performed first experimental tests of this method at the soft X-ray FEL user facility FLASH. The measured pulse duration approaches 1 fs (FWHM) at the wavelength of 5 nm.

Abstract: The calibrator is one of the most important factors in the calibration of various laser 3D scanning instruments. The requirements for diffuse reflection surface are specially emphasized in many national standards. In this study, the spherical calibrator and plane calibrator compara-tive measurement experiments were carried out. The black ceramic standard sphere, white ce-ramic standard sphere, metal standard sphere, metal standard plane and white ceramic standard plane were used to test the laser 3D scanner. In the spherical calibrators comparative measure-ment experiments, the results indicated that the RMS of the white ceramic spherical calibrator with reflectance about 60% is 10 times that of the metal spherical calibrator with the reflectance of about 15%, and the RMS of the black ceramic spherical calibrator with reflectance of about 11% is of the same order as the metal spherical calibrator. In the plane calibrators comparative measurement experiments, the RMS of flatness measurement is 0.077 mm for metal plane cali-brator with reflectance of 15%, and 2.915 mm for ceramic plane calibrator with reflectance of 60%. The results show that when the optimal measurement distance and incident angle are selected, the reflectance of the calibrator has a great effect on the measurement results, regardless of the outlines or profiles. Based on the experiments, it is recommended to use the spherical calibrator or the standard plane with reflectance of around 18% as the standard, which can obtain the rea-sonable results. In addition, it is necessary to clearly provide the material category and surface reflectance information of the standard when calibrating the scanner according to the measure-ment standard.

In the past years, our knowledge of coastal environments has been enriched by remotely sensed data. However, to successfully extract information from a combination of different sensors systems, it should be understood how these interact with the common coastal environment. In this research we co-analyze two sensor systems: Terrestrial Laser Scanning (TLS) and satellite based Synthetic Aperture Radar (SAR). TLS shows large potential for examining coastal processes thanks to the possibility to retrieve repeated, accurate and dense topographic information in a rapid and non-invasive manner. However, TLS presents some limits due to its high economic costs and limited field of view. SAR systems are among the most used active remote sensor system for Earth Observation. Despite their relatively low resolution, SAR systems provide the ability to monitor and map coastal areas with complete, repeated and frequent coverage, penetrating through clouds and providing all weather monitoring. Moreover, Sentinel-1 SAR images are freely available. The availability of a permanently installed TLS system (PLS, Permanent Laser Scanner) allows us, to extensively compare Sentinel-1 SAR data and topographic laser scans during different conditions on a sandy beach. PLS data are compared with simultaneous Sentinel-1 SAR images in order to investigate the combined use of PLS and SAR in coastal environments. The purpose of this comparison is the investigation of a possible relation between PLS and SAR data: knowing their relation, SAR dataset could be correlated to beaches characteristics. Meteorological and surface roughness have also been taken into consideration in the evaluation of the correlation between PLS and SAR data. The permanently installed laser scanner for the present study is located in Noordwijk (the Netherlands). A generally positive but low correlation exists between the two variables. When considering weather phenomena, their correlation increases and shows a dependence on wind directions and speed. The correlation with the surface roughness, evaluated in terms of root-mean squared height, also depends on specific wind speed and directions.

We utilized laser irradiation as a potential technique in tuning the electrical performance of NiOx/SiO2 thin film transistors (TFTs). By optimizing the laser fluence and the number of laser pulses, the TFT performance is evaluated in terms of mobility, threshold voltage, on/off current ratio and subthreshold swing, all of which were derived from the transfer and output characteristics. The 500 laser pulses irradiated NiOx/SiO2 TFT exhibited an enhanced mobility of 3 cm2/V-s from a value of 1.25 cm2/V-s for as-deposited NiOx/SiO2 TFT. The laser-irradiated NiOx material likely has a significant concentration of defect gap states, which could also be involved in light absorption processes. Second, and more importantly, the excess energy that the photogenerated charge carriers possess (due to the significant difference between the photon energy and the bandgap of NiOx), combined with the very high light intensity, would result in complex thermal and photo thermal changes thus resulting in an enhanced electrical performance of p-type NiOx/SiO2 TFT structure.

Extracorporeal shock wave therapy (ESWT) is a well investigated and widely used treatment modality for a number of musculoskeletal disorders. A limitation of ESWT is its potential painfulness at higher, clinically relevant energy flux density (EFD), which may limit its applicability and, thus, effectiveness. Various studies in the literature demonstrated that neither application of a higher number of extracorporeal shock waves with lower EFD nor use of local anesthesia may solve this problem. Based on the results of several other studies in the literature it is hypothesized here that in patients suffering from musculoskeletal disorders that can be treated with ESWT, pretreatment with a pulsed, high power laser with a wavelength of 904 or 905 nanometers (hereafter: "laser pretreatment") does not only allow to apply higher EFDs in subsequent ESWT but actually results in faster and/or better treatment outcome than ESWT without laser pretreatment. Accordingly, it is hypothesized here that combining ESWT with laser pretreatment leads to synergistic effects and, thus, is superior to either treatment modality alone. Confirming this hypothesis in preclinical and clinical research may raise significance and increase the use of ESWT in physical and rehabilitation medicine, with immediate benefit for patients.

The inherent trace quantity of primary fatty acid amides found in biological systems presents challenges for analytical analysis and quantitation, requiring a highly sensitive detection system. The use of microfluidics provides a green sample preparation and analysis technique through small-volume fluidic flow through micron-sized channels embedded in a PDMS device. Microfluidics provides the potential of having a micro total analysis system where chromatographic separation, fluorescent tagging reactions, and detection are accomplished with no added sample handling. This study describes the development and optimization of a microfluidic-laser indued fluorescence (LIF) analysis and detection system that can be used for the detection of ultra-trace levels of fluorescently tagged primary fatty acid amines. A PDMS microfluidic device was designed and fabricated to incorporate droplet-based flow. Droplet microfluidics have enabled on-chip fluorescent tagging reactions to be performed quickly and efficiently, with no additional sample handling. An optimized LIF optical detection system provided fluorescently tagged primary fatty acid amine detection sub-fmol (436 amol) LODs. The use of this LIF detection provides unparalleled sensitivity, with detection limits several orders of magnitude lower than currently employed LC-MS techniques and might be easily adapted for use as a complementary quantification platform for parallel MS-based -omics studies.

We propose a new approach of extending the laser filament plasma channel. By adding a circular aperture quartz plate before the focusing lens, the extension of the plasma channel is doubled. The effects of different diameters, thicknesses of the circular aperture quartz plate and different pulse energies on the length of the plasma channel were investigated. The experimental results show that the thickness of the quartz plate and the depth of the hole have little effects on the plasma channel of the filament, and the diameter of the hole in the center of the quartz plate has a significant effect on the length of the optical filament. The moving-focus model is used to explain the extension of the optical filament.

Nowadays, the uses of laser and optics in the medical areas are extremely vivid, especially low-level laser therapy. The light with the wavelength of 633 nm to 1200 nm could penetrate and propagate deep in biological tissue. To develop the low-level laser therapy device, optimizing light delivery is critical to accurately stimulate the biological effects inside the biological tissue. Nevertheless, each form of the tissues at each zone on the body had various refractive optic, absorption, scattering, and anisotropy coefficients. This paper describes the simulation results of low-level laser propagation from skin surface at the lower spine, the knee, the femur and the prostate gland with four wavelengths (633 nm, 780 nm, 850 nm, and 940 nm) by the Monte Carlo method. These simulation results are the base for developing the low-level laser therapy device, that could be used in clinical for treating the fracture, knee osteoarthritis, spinal degeneration, and benign prostatic hypertrophy.

A novel mathematical model is developed to calculate the temperature distribution on the surface and bulk of a steel plate under the laser hardening process. The model starts with the basic heat equation then it is developed into a volumetric form and is connected to the various solid existing phases. The proposed model is based on three influencing parameters of the laser hardening process which are the velocity of the laser spot and irradiation time. The results are compared with the available experimental data reported in the literature. The volumetric model provides an assessment of temperature distribution in both the vertical and horizontal axis. Laser irradiation at sufficiently high fluence can be used to create a solid-state phase change on the surface. Primary calculations show that the temperature profile has a Gaussian distribution in horizontal x and y-axis and presents an exponentially decreasing in the horizontal and vertical depth directions.

This work examines atomic and molecular signatures in laser-induced plasma in standard ambient temperature and pressure environments, including background contributions to the spectra that depend on the laser pulse-width. Investigations include solids, gases, and nano-particles. Abel inversions of measured line-of-sight data reveal insight into the radial plasma distribution. For nominal 6 nanosecond laser pulses and for pulse-energies in the range of 100 to 800 mJ, expansion dynamics and turbulence due to shock phenomena are elucidated to address local equilibrium details that are frequently assumed in spatially averaged emission spectroscopy. Chemical equilibrium computations reveal temperature dependence of selected plasma species. Specific interests include atomic hydrogen (H) and cyanide (CN). Atomic hydrogen spectra indicate axisymmetric shell structures and isentropic expansion of the plasma kernel over and above the usual shockwave. The recombination radiation of CN emanates within the first 100 nanoseconds for laser-induced breakdown in a 1:1 CO2:N2 gas mixture when using nanosecond laser pulses to create the micro-plasma. The micro-plasma is generated using 1064 nm, 150 mJ, 6 ns Q-switched Nd:YAG laser radiation. Measurements of the optical emission spectra utilize a 0.64 m Czerny-Turner type spectrometer and an intensified charge-coupled device.

Selective laser melting is an emerging Additive Manufacturing (AM) technology for metals. Intricate three-dimensional parts can be generated from the powder bed by selectively melting the desired location of the powders. The process is repeated for each layer until the part is built. The necessary heat is provided by a laser. Temperature magnitude and history during SLM directly determine the molten pool dimensions, thermal stress, residual stress, balling effect, and dimensional accuracy. Laser-matter interaction is a crucial physical phenomenon in the SLM process. In this paper, five different heat source models are introduced to predict the three-dimensional temperature field analytically. These models are known as steady state moving point heat source, transient moving point heat source, semi-elliptical moving heat source, double elliptical moving heat source, and uniform moving heat source. The analytical temperature model for all of the heat source models are solved using three-dimensional differential equation of heat conduction with different approaches. The Steady state and transient moving heat source are solved using separation of variables approach. However, the rest of models are solved by employing the Green’s functions. Due to the high magnitude of the temperature in the presence of the laser, the temperature gradient is usually high which has a substantial impact on thermal material properties. Consequently, the temperature field is predicted by considering the temperature sensitivity thermal material properties. Moreover, due to the repeated heating and cooling, the part usually undergoes several melting and solidification cycles, this physical phenomenon is considered by modifying the heat capacity using latent heat of melting. Furthermore, the multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the layers have an impact on heat transfer mechanisms. The proposed temperature field models based on different heat source approaches are validated using experimental measurement of melt pool geometry from independent experimentations. The detailed explanation of the comparison of models is also provided. Moreover, the effect of process parameters on the balling effect is also discussed.

Using nanoindentation under various strain rates, the mechanical properties of a selective laser melted (SLM) SKD61 at the 800 mm/s scan speed was investigated and compared to SLM H13. No obvious pile-up due to the ratio of the residual depth (h_f) and the maximum depth (h_max) being lower than 0.7 and no cracking were observed on any of the indenter surfaces. The nanoindentation strain-rate sensitivity (m) of SLM SKD61 was found to be 0.034, with hardness increasing from 8.65 GPa to 9.93 GPa as the strain rate increased between 0.002 s⁻¹ and 0.1 s⁻¹. At the same scan speed, the m value of SLM H13 (m = 0.028) was lower than that of SLM SKD61, indicating that the mechanical behavior of SLM SKD61 was more critically affected by the strain rate compared to SLM H13. SLM processing for SKD61therefore shows higher potential for advanced tool design than for H13.

In most studies reported in literature, a flat, constant coefficient is used to convert the amount of optical power required at the input of an optical link into the effective power consumption. This constant coefficient approach is very simple to apply but not accurate, since laser efficiencies are dependent on the optical output power in addition to the operating temperature. In this paper the relationship between laser wall plug efficiency and optical power output is investigated and the effect of this variance on optical links and on-chip laser source electric power consumption is presented

The resonance spectra of neutral silver indicate self-absorption for the studied Ag I lines at the wavelengths of 327.9 nm and 338.2 nm. The center dip is associated with self-reversal due to self-absorption in the plasma. The Q-switched radiation of 355 nm, 532 nm, or 1064 nm from a Nd:YAG laser device generates the plasma at the surface of silver nano-material targets, with experiments conducted in standard ambient temperature and pressure laboratory air. Procedures for recovery of the spectral line shapes confirm that over and above the effects of self-reversal, line shape distortion are important in the analysis. The work discusses parameters describing self-absorption when using fluence levels of 2 to 33 J/cm² to generate the plasma. Furthermore, subsidiary calibration efforts that utilize the hydrogen alpha line of the Balmer series show that the Ag I lines at 827.35 nm and 768.7 nm are optically thin.

Outer particles collision with certain dynamic object is not a pure impact wear behavior; it is typically accompanied by sliding wear phenomena. This study aimed investigating the impact-sliding wear performance of three different TC17 titanium alloys. One was untreated, and the other two were subjected to laser shock peening (LSP) by 5 and 7 J pulse energy, respectively. Wear test was performed on a novel impact-sliding wear testing rig, which can realize multiple impact-sliding motions by changing motion parameters in x and z directions. Present results showed that wear resistance of both treated samples improved compared with the untreated alloy. Given the increase in wear cycles, increment in wear rate of the untreated sample was constantly higher than those of treated samples. All results can be attributed to the increase in surface hardness of the material and residual compressive stress, which was also introduced after LSP.

The study proposes laser shock peening without a coating of high strength ultrafine bainitic steel to mitigating the fatigue failures for automotive and structural engineering applications. Laser pulse density of 2500 pulses/cm2 (75% overlapping) was optimised based on the induced residual stresses for employing the wide range of characterisations. The roughness and topographic results showed that surface roughening was controlled by tuning the laser pulse density. The High-Resolution X-ray Diffraction analysis confirmed the lattice misorientation resulting peak shift and the trend towards martensite phase transformations. The electron microscopic micro/nanostructure analyses revealed the grain refinement features such as nano-twins, micro shear bands and shear cells. The work hardening depth and nanomechanical properties were significantly enhanced. A fully reversed (R= -1) high-cycle fatigue tests extended the lifespan by an average of fifteen times than the untreated. Also, it has potential to repair the structural components effectively.

Laser scanning systems make use of Light Detection and Ranging (LiDAR) technology to acquire accurately georeferenced sets of dense 3D point cloud data. The information acquired using these systems produces better knowledge about the terrain objects which are inherently 3D in nature. The LiDAR data acquired from mobile, airborne or terrestrial platforms provides several benefit over conventional sources of data acquisition in terms of accuracy, resolution and attributes. However, the large volume and scale of LiDAR data have inhibited the development of automated feature extraction algorithms due to the extensive computational cost involved in it. Moreover, the heterogeneously distributed point cloud, which represents objects with varying size, point density, holes and complicated structures pose a great challenge for data processing. Currently, geospatial database systems do not provide a robust solution for efficient storage and accessibility of raw data in a way that data processing could be applied based on optimal spatial extent. In this paper, we present Global LiDAR and Imagery Mobile Processing Spatial Environment (GLIMPSE) system that provides a framework for storage, management and integration of 3D LiDAR data acquired from multiple platforms. The system facilitates an efficient accessibility to the raw dataset, which is hierarchically represented in a geographically meaningful way. We utilise the GLIMPSE system to automatically extract road median from Airborne Laser Scanning (ALS) point cloud. In the first part of this paper, we detail an approach to efficiently retrieve the point cloud data from the GLIMPSE system for a particular geographic area based on user requirements. In the second part, we present an algorithm to automatically extract road median from the retrieved LiDAR data. The developed road median extraction algorithm utilises the LiDAR elevation and intensity attributes to distinguish the median from the road surface. We successfully tested our algorithms on two road sections consisting of distinct road median types based on concrete and grass-hedge barriers. The use of GLIMPSE improved the efficiency of the road median extraction in terms of fast accessibility to ALS point cloud data for the required road sections. The developed system and its associated algorithms provide a comprehensive solution to the user's requirement for an efficient storage, integration, retrieval and processing of large volumes of LiDAR point cloud data. These findings and knowledge contribute to a more rapid, cost-effective and comprehensive approach to surveying road networks.

Stess in laser cladding coating is an important factor affecting the safe operation of remanufacturing components. Ultrasonic testing has become a hot direction in nondestructive evaluation of stress, because it has the advantages of safety, non-destructive and on-line detection. This paper provides a review of ultrasonic testing for stress in remanufacturing laser cladding coating. It summarizes the recent research outcomes on ultrasonic testing for stress, analyzes mechanism of ultrasonic testing for stress. Remanufacturing laser cladding coating shows typical anisotropic behaviors, the ultrasonic testing signal in laser cladding coating is influenced by many complex factors, such as microstructure, defect, temperature and surface roughness, etc. At present, ultrasonic testing for stress in laser cladding coating can only be done roughly. The paper discusses active mechanism of micro / macro factors to the reliability of stress measurement and the impact of stress measurement to the quality and safety of remanufacturing components. Base on the discussion, the paper proposes strategies for acquisition of nondestructive, rapid and accurate measurement of stress in remanufacturing laser cladding coating.

Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI–TOF MS) is a commonly used technique for analyzing large biomolecules. However, the utilization of organic matrices limits the small-molecule analysis because of the interferences in the low-mass region and reproducibility issues. To overcome these limitations, a surface-assisted laser desorption/ionization (SALDI), which utilizes nanostructured metallic surfaces, has been developed. Herein, a novel approach for SALDI–MS was proposed using nanoengineered gold shell with nanogaps on the silica core (SiO2@Au NGS), which is an emerging material due to its excellent heat-generating capabilities. The gold shell thickness was controlled by adjusting the concentration of gold precursor for the growth of gold nanoparticles. SALDI-MS measurements were performed on a layer formed by drop-casting a mixture of SiO2@Au NGS and analytes. At the optimized process, the gold shell thickness was observed to be 17.2 nm, which showed the highest absorbance. The ion desorption efficiency was confirmed with a survival yield upon fragmentation. Based on the enhanced SALDI capability, SiO2@Au NGS was utilized to detect various small molecules including amino acids, sugars, and flavonoids. The limits of detection, reproducibility, and salt tolerance of SiO2@Au NGS demonstrate its potential as an effective and reliable SALDI material for small-molecule analyses.

Recent studies have indicated that terahertz time-domain spectroscopy (THz-TDS) can stably and efficiently acquire output spectra using an affordable and compact multimode laser diode (MMLD) with delayed optical feedback as the light source. This research focused on a numerical analysis of the optimal conditions for employing an MMLD with delayed optical feedback (chaotic oscillating laser diode) in THz-TDS, utilizing multimode rate equations. The findings revealed that the intermittent chaotic output generated by the MMLD, characterized by concurrent picosecond pulse oscillations lasting several tens of picoseconds, proves to be highly effective for THz-TDS. By appropriately setting the amounts of injection current and optical feedback, and the delay time of optical feedback, intermittent chaotic oscillation can be attained within a considerably broad parameter range. Moreover, both the MMLD output spectrum and the THz-TDS output spectrum exhibit a consistently stable shape at the microsecond scale, demonstrating the attractor properties inherent in an MMLD with delayed optical feedback.

This work presents first time successfully fabricated silica few-mode microstructured optical fiber (MOF) with hollow GeO2-doped ring core and strongly induced twisting up to 790 revolutions per meter. Some technological issues for manufacturing of GeO2-doped supporting elements for large hollow cores as well as described above complicated spun MOFs are discussed. We introduce some results of tests, performed for pilot samples of designed and manufactured described above untwisted and twisted MOFs with outer diameter 65 µm and hollow ring core inner diameter 30.5 µm under wall thickness 1.7 µm and refractive index difference n=0.030, including their geometrical parameters, basic transmission characteristics and measurements of far-field laser beam profile patterns.

Ultrafast laser 3D lithography based on non-linear light-matter interactions, widely known as multi-photon lithography (MPL), offers unrivaled precision rapid prototyping and flexible additive manufacturing options. 3D printing equipment based on MPL are already commercially available, yet there is still no comprehensive understanding of factors determining spatial resolution, accuracy, fabrication throughput, repeatability, and standardized metrology methods for the accurate characterization of the produced 3D objects and their functionalities. The photoexcitation mechanisms, spatial-control or photo-modified volumes, and the variety of processable materials are topics actively investigated. The complexity of the research field is underlined by limited understanding and fragmented knowledge of light-excitation and material response. Research to date has only provided case-specific findings on photoexcitation, chemical modification, and material characterization of the experimental data. In this review, we aim to provide a consistent and comprehensive summary of the existing literature on photopolymerization mechanisms under highly confined spatial and temporal conditions, where, besides the excitation and cross-linking, parameters such as diffusion, temperature accumulation, and the finite amount of monomer molecules start to become of critical importance. Key parameters such as, photoexcitation, polymerization kinetics, and the properties of the additively manufactured materials at the nanoscale in 3D are examined, whereas, the perspectives for future research and as well as emerging applications are outlined.

This article discusses laser-induced laboratory-air plasma measurements and analysis of hydroxyl (OH) ultraviolet spectra. New experiments with Q-switched laser pulses illustrate occurrence of molecular recombination spectra for time delays of the order of several dozen of microseconds after plasma initiation. The computation of the emission spectra utilizes line strength data that are communicated as a supplementary file. Applications of detailed OH computations include laser-induced plasma and combustion analyses, to name but two applications.

This paper presents a novel segmentation algorithm specially developed for applications in 3D point clouds with high variability and noise, particularly suitable for heritage building 3D data. The method can be categorized within the segmentation procedures based on edge detection. In addition, it uses a graph-based topo-logical structure generated from the supervoxelization of the 3D point clouds, which is used to make the clo-sure of the edge points and to define the different segments. The algorithm provides a valuable tool for generating results that can be used in subsequent classification tasks and broader computer applications dealing with 3D point clouds. One of the characteristics of this segmentation method is that it is unsupervised, which makes it particularly advantageous for heritage applications where labelled data is scarce. It is also easily adaptable to different edge point detection and supervoxelization algorithms. Finally, the results show that the 3D data can be segmented into different architectural elements, which is important for further classification or recognition. Extensive testing on real data from historic buildings demonstrates the effectiveness of the method. The results show superior performance compared to three other segmentation methods, both globally and in the segmentation of planar and curved zones of historic buildings.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

Agriculture is an important sector of European Union in societal , economic and environmental dimensions. Sustainability of the sector require improvements in its key operations. Weeding is one of the crucial operation having impact on farms’ productivity, safety for farmers, food security and environmental state. To achieve EU policy goals of sustainable agriculture there are needed new technical and organizational solutions. One of the advanced techniques are laser based weeding technique. It is important to understand well the impacts of introduction of these tech-niques to the markets and agricultural practice in sustainability context. For that reason Social Life Cycle Assessment was performed. The method was based on participatory approach. The as-sessment was carried in three perspectives: general society, farmers, and business perspective re-lated to agriculture. Expert interviews based on questionnaires and workshops were realized to get the opinions on the impacts of a new laser technique on particular aspects of its implementation. The results show generally positive impact in all perspectives, especially in the perspective of farmers.

With the megatrend of digitalization, the demand for sensors in previously difficult to access scenarios is increasing. Filament-shaped sensors (FSS) are ideal for this demand especially in applications in which the monitoring of textile structures is the focus. Electrically conductive bicomponent filaments based on thermoplastic polyurethane (TPU) and doped with carbon nanotubes (CNTs) offer great potential due to the flexible mechanical properties. Through the core-conducting, bicomponent structure the sensing material is protected from environmental factors such as surrounding conductive materials and external moisture. The insulating material, however, simultaneously complicates the contacting method in order to measure sensing changes in the conductive core. In this work laser cutting is employed as a technology in order to expose the conductive core of the filaments. The filament is then coated with silver and mechanically crimped, providing both a conductive interface for the data acquisition device as well as a protective layer. Laser parameters (power and speed) are investigated in order to identify the parameters with the best cutting properties which is analyzed visually as well as electrically. The work conducted here can then be used in order to provide a robust and reproducible contacting method for core-conducting TPU filaments for strain sensing applications.

Technical components should be produced sustainably and are subject to growing demands in terms of durability and reliability. To meet these expectations, the development of thermochemical processes is auspicious. Titanium alloys, which have a comparatively high gas solubility, allow temporary hydrogen (H) loading, often called thermo hydrogen treatment (THT). THT causes lattice deformation and reduces the β transformation temperature. These effects enable an adjustment of the microstructure, which improves the mechanical properties as compared to those produced conventionally. Furthermore, the process is applicable to complex geometries that cannot be surface hardened by mechanical surface treatment techniques. The investigation presented intends to realize a local microstructure gradient in additively via laser-powder bed fusion (L-PBF) manufactured cylindrical Ti–6Al–4V specimens by changing the distribution and morphology of strengthening precipitates as well as the β grain size depending on the distance to the surface, which should improve the material fatigue properties. To evaluate the mechanical properties of such THT-induced microstructure gradients, the resulting change in fatigue life in the LCF and HCF range was determined by stress-controlled cyclic deformation tests. Besides, the resulting microstructure was characterized by means of XRD and TEM. In addition to the additively manufactured and thermo hydrogen treated cylindrical specimens, conventionally produced tube-like specimens were thermo hydrogen treated and examined. For the THT-induced microstructure gradients, numerically simulated H concentration profiles as well as experimentally determined hardness profiles were used for the evaluation of the THT process. The study shows that H-loading at 500°C and H-degassing at 750°C, followed by aging at 550°C, allows the establishment of a microstructure gradient that shows an 8% improvement in fatigue properties compared to a reference condition without THT. The reason for this improvement is an increased volume fraction secondary alpha phase in the near-surface area of the specimens. Moreover, the results show that the process is applicable a tube-like specimen with varying wall thicknesses.

This paper presents a numerical study on the laser shock wave propagation in a 3D woven CFRP material by means of detailed and homogenized FE models. The aim of the study is to numerically characterize the shock wave response of the 3D woven CFRP in terms of back face velocity profiles and the induced damage and to investigate whether the detailed FE models could be replaced by homogenized FE models. The 3D woven geometry was designed using the TexGen software, while the numerical analyses were executed using the LS-Dyna explicit FE software. A high-strain rate behavior was considered for the matrix. The fiber bundles in the detailed models were modeled as a high fiber content unidirectional composite laminate, with its mechanical properties calculated by micromechanical equations. Both for the fiber bundles of the detailed model and the homogenized models a progressive damage material model was applied. The results of the detailed model reveal a considerable effect of material’s architecture on the shock wave propagation and the sensitivity of the back face velocity profile to the spot location. Consequently, the homogenized model is not capable of accurately simulating the shock wave response of the 3D woven composite. Moreover, the detailed predicts with high accuracy matrix cracking in the resin-rich areas and in the bundles as well as fiber failure. On the contrary, the homogenized model predicts matrix cracking at the same areas and no fiber failure.

This paper is a follow-up to a previous study that was conducted in a research forest and identified the optimal method for Diameter at Breast Height (DBH) estimation as a circular scanning and fitting ellipses to 4cm stem cross-sections at breast height. The aim of this study was to determine whether the identified method is applicable to natural boreal forests as well. The iPad Pro LiDAR scanner was used to acquire point clouds for 15 sites representing a range of natural boreal forest conditions in Ontario, Canada, and estimate DBH. The secondary objective was to determine if tested stand (Species composition, age, density, understory) or tree (Species, DBH) factors affected the accuracy of estimated DBH. Overall, estimated DBH values were within 1cm of actual DBH values for 78 of 133 measured trees (59%). An RMSE of 1.5cm (8.6%) was achieved. Stand age had a large effect (&gt;0.15) on the accuracy of estimated DBH values, while density, understory, and DBH had moderate effects (0.05-0.14). No trend was identified between accuracy and stand age. Accuracy improved as understory density decreased and as tree DBH increased. Inertial Measurement Unit (IMU) and positional accuracy errors with the iPad Pro scanner limit the feasibility of using this device for forest inventories.