The effect of Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results demonstrate that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites in the weld metal, and significantly improve the toughness. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. Excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties.

In this study, rheological properties of the bread wheat flour dough from 6 wheat genotypes were determined. For the pereparation of flour, 3 red bread (Pandas, Sagitorya, Pehlivan) and 3 white bread (Kaşifbey, Göktan, Ceyhan-99) were selected as wheat genotype. To determine the rheological properties of the wheat flour dough, farinograph, extensograph, mixolab and glutograph devices were used. According to the results of the Farinograph analysis, the average development time of wheat White and red genotypes were 1.95 minutes and 8.96 minutes, respectively. According to the extensograph results of the flour samples, the most extended stability value was determined with 7.47 min in Ceyhan-99 cultivar. As a result of the research, it was determined that flour yields of red bread varieties were higher other genotypes, gas retention capacities of white bread flours were showed high result in extensograph application and resistance of dough to elongation was higher. In the Mixolab analysis, it determined that white bread wheat varieties have higher values in terms of kneading properties and gluten properties, and red bread wheat varieties have higher values in values of viscosity, amylase value and starch retrogradation.

Friction stir processing (FSP), a severe plastic deformation process, was applied on commercially pure Ti to obtain an improved microstructure. The process yielded a refined microstructure and higher mechanical properties at room temperature (RT). Yet the microstructure was found to contain bright bands demonstrating high hardness values of about 500 HV. High resolution scanning electron microscopy (HRSEM) as well as electron back scattering diffraction (EBSD) analysis indicated that these bands were composed of extra-fine equiaxed α-Ti grains with an average radius of 1-2 microns. In addition, a retained β-phase was detected at the boundaries of these α-Ti grains, together with a small quantity of separate β grains. The results of a fractography study conducted on broken tensile specimens showed that the FSP’ed material was free of defects and that the fracture started at these bands. It is proposed that these bright bands are due to excessive deformation occurring during the processing stage, leading to an accelerated dynamic recrystallization (DRX) process. In turn, these heavy deformation regions act as a strengthening constituent, making the material superior to the parent material as far as its mechanical RT properties are concerned. Consequently, this means that FSP of CP-Ti has the potential to serve as an industrial means of improving the mechanical properties of the material.

Cannabidiol (CBD) is a safe and non-psychotropic phytocannabinoid with a wide range of potential therapeutic antiinflamatory and antioxidant activity. Due to its lipophilicity, it is normally available dissolved in oily phases. The main aim of this work was to develop and characterize a new formulation of a microemulsion with a potential anti-inflammatory and antioxidant action for topical treatment of inflammatory skin disorders. The micro-emulsion system was obtained from a 20% CBD oil as hydrophobic phase, Labrasol/Plurol Oleique (1:1) as surfactant and cosurfactant (S/CoS) respectively and an aqueous vegetal extract obtained from S. ebulus L. ripe fruits, with a potential anti-oxidant and anti-inflammatory activity, as water phase. A pseudo-ternary phase diagram was elaborated, selecting an optimal proportion of 62% (S/CoS), 27% CBD oil and 11% water and, after testing its reproducibility, the aqueous phases were replaced by the vegetal hydrophilic extract. The defined systems were characterized in terms of conductivity, droplet size by laser scattering, compatibility of components by differential scanning calorimetry and rheological properties using a rotational rheometer. The designed microemulsion showed good stability and a slight pseudo-plastic behavior. The release properties of CBD from the oil phase and caffeic acid from the water phase of the microemulsion were studied by in vitro diffusion experiments using flow-through diffusion cells in comparison to a CBD oil and a microemulsion only with CBD as active substance. It was evidenced that the inclusion of the original oil in microemulsions did not provoke a significant modification of the release of CBD, incorporating the possibility of including hydrophilic active compounds in the formulation, stablishing an interesting strategy for the development of future formulations.

This study focused on evaluating the potential of natural fermentation of pea flour (F) to improve the release of antioxidant compounds. Two fermentation conditions of F were performed: 1: 36.4% w/w, 24 h, 30°C (FF1); 2: 14.3% w/w, 24 h, 37°C (FF2); pH values decreased to 4.4-4.7, with a predominance of lactic acid bacteria. An increment of the proteolysis degree (TNBS method) (greater for FF2), polypeptides aggregation and decrease of solubility, increase of < 2 kDa peptides, and increase in the ORAC potency of PBS-soluble fractions after fermentation was demonstrated. After simulated gastrointestinal digestion (SGID, COST-INFOGEST), FF1D and FF2D showed greater proteolysis degrees (63 and 53%) than F1D and F2D (45%), with differences in the molecular composition of the different digests. ORAC and HORAC potencies increased in all cases. FF2D presented the greater ORAC value, with higher activities for > 4 kDa, some in the range 2 to 0.3 kDa. and < 0.10 kDa fractions. Fermentation also increased the 60 % ethanol extracted phenolic compounds, mainly flavonoids, and the ORAC activity. After SGID, the flavan-3-ols disappeared but some phenolic acids increased respect to F. Fermentation in condition 2 was considered the most appropriate to obtain a functional antioxidant ingredient.

Present study focuses on the synthesis and characterisation of a lightweight ceramic material with electromagnetic interference (EMI) shielding properties, achieved using mullite containing micrometer-sized hollow spheres (cenospheres) and CoFe2O4 nanoparticles. The research explores compositions with varying CoFe2O4 content, ranging from 0 up to 20 wt.%. Сonventional sintering in an air atmosphere is carried out at a temperature between 1100-1300 °C. The addition of ferrite nanoparticles was found to enhance the sintering process of cenospheres, resulting in improved material density and mechanical properties. Furthermore, the study reveals a direct correlation between the concentration of ferrite nanoparticles and the electromagnetic properties of the. By increasing the concentration of ferrite nanoparticles, the electromagnetic shielding effect of the material (saturation magnetization (Ms) and remanent magnetization (Mr)) was observed to strengthen. These findings provide valuable insights into the design and development of lightweight ceramic materials with enhanced electromagnetic shielding capabilities. The synthesized ceramic material holds promise for various applications that require effective electromagnetic shielding, such as in electronics, telecommunications, and aerospace industries.

Ready-to-eat fresh fruit have an increasing presence in international markets due to its convenience and health benefits. However, these produces are highly perishable and efficient technologies to increase their shelf life are needed. In the present research, different citrus fruit species and cultivars from organic farming were assayed to obtain enzymatically citrus segments. The best results in terms of segment quality were observed for ‘Hernandina’ clementine which was chosen to make a new ready-to-eat produce based on peeled citrus segments packaged in glass jars with slight syrup made on citrus juice and organic sugar cane. The most appreciated syrup was those containing 50-50 (v/v) of ‘Fino’ lemon juice and ‘Hernandina’ clementine based on the sensory scores given by the panellists. In addition, different pasteurization treatments were assayed to preserve the new produce safety and nutritional and sensory quality properties during storage at cold temperature. Results showed that pasteurization treatment at 50 °C for 45 min could be enough to avoid microbial contamination with mesophilic and psychrophilic aerobic bacteria or yeast and mould and to maintain sensory properties until five weeks of storage at 4 °C. In addition, only a 10 % reduction of vitamin C was observed from fresh segments or syrup until the end of storage period, showing that the new ready-to-eat produce would conserve high bioactive compound content and health benefits after pasteurization and prolonged cold storage.

The protein extract of Ulva australis hydrolyzed with alcalase and flavourzyme investigated multi-functional properties, including total antioxidant capacity (TAC), collagenase inhibitory and antibacterial activities. The #5 fraction (SP5) and #7 fraction (SP7) of U. australis hydrolysate from cation-exchange chromatography showed significantly high TAC, collagenase inhibitory and antibacterial effects against Propionibacterium acnes, and only Q3 fraction from anion-exchange chromatography showed high multi-functional activities. The eight peptides among 42 peptides identified by MALDI-TOF/MS and Q-TOF/MS/MS were selected from the results to screen molecular docking on target proteins, and were synthesized. Thr-Gly-Thr-Trp (TGTW) showed ABTS [2,2′-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid)] radical scavenging activity. Effect TAC as Trolox equivalence was dependent on the concentration of TGTW. The Asn-Arg-Asp-Tyr (NRDY) and Arg-Asp-Arg-Phe (RDRF) possessing collagenase inhibitory activity increased according to the increase of concentration and the IC50 values of them were 0.95 mM and 0.84 mM, respectively. Peptides, RDRF and His-Ala-Val-Tyr (HAVY) showed anti-P. acnes effects with IC50 values of 8.57 mM and 13.23 mM, respectively. These results suggest that the U. australis hydrolysate could be a resource for the application of effective nutraceuticals and cosmetics.

Hydrotalcites (HTlc) represents a class of nanostructured layered materials that may be employed in a variety of applications, from green to bio technologies. In this paper, we report an investigation on HTlc made of Mg and Fe, recently employed to improve the growth in vitro of osteoblasts within a keratin sponge. We have carried out an analysis of powder materials and of HTlc dispersed in keratin and spin-coated on a Si/SiO2 substrate at different temperatures. A DC magnetic study of the powders has been carried out with a Quantum Design Physical Property Measurement System, equipped with a Vibrating Sample Magnetometer. The data gathered prove that these HTlc are fully paramagnetic, and keratin shows a very small magnetic response. Optical and Atomic Force Microscopy analyses of the thin films provide a detailed picture of clusters randomly dispersed in the films with various dimensions. The magnetic properties of these films have been characterized using the Nano Magneto Optical Kerr Effect (NanoMOKE) down to 7.5K. The data collected show that the local magnetic properties can be mapped with a micrometric resolution distinguishing HTlc regions from keratin ones. This approach opens new perspectives in the characterization of these composite materials.

This study investigated the impact of boron and copper on the microstructure and mechanical properties of Spheroidal graphite Cast Iron (SCI). The addition of boron increased the ferrite content, while copper increased the stability of pearlite. The interaction between boron and copper significantly increased the ferrite content. Differential Scanning Calorimetry (DSC) revealed that boron decreased the enthalpy change of the α + Fe3C -> γ transformation and increased the enthalpy change of the α -> γ transformation. The addition of boron and copper reduced the tensile and yield strength but increased elongation and impact energy. The findings provide valuable insights into the effect of boron and copper on SCI, facilitating the design and development of high-performance SCI materials.

This paper focuses on the effect of malondialdehyde-induced oxidative modification (MiOM) on the gel properties of duck myofibrillar proteins (DMPs). DMPs were first prepared and treated with oxidative modification at different concentrations of malondialdehyde (0, 0.5, 2.5, 5.0 and 10.0 mmol/L). The physicochemical changes (carbonyl and free thiol group content) and gel properties (gel whiteness, gel strength, water holding capacity, rheological properties and mi-cro-structural properties) were then investigated. The results showed that the content of protein carbonyl groups increased with increasing MDA oxidation (P<0.05), while the content of free thiol groups decreased significantly (P<0.05). Meanwhile, there was a significant trend of decrease in gel whiteness; the hardness and water-holding capacity of protein gels increased significantly under the oxidation of low concentration of MDA (0-5 mmol/L), while the hardness of gels decreased under the oxidation of high concentration (10 mM). The storage modulus and loss modulus of oxidized DMPs also increased with increasing concentration; moreover, microstructural analysis confirmed that the gels oxidized at low concentrations were more compact and homogeneous in terms of pore size compared to the high concentration or blank group. In conclusion, moderate oxidation of malondialdehyde was beneficial to improve the gel properties of duck; however, excessive oxidation was detrimental to the formation of dense structured gels.

The Chiltan Formation is a potential hydrocarbon-producing reservoir in the Indus Basin, Pakistan. However, its diagenetic alterations and heterogeneous behavior lead to significant challenges in accurately characterizing the reservoir and production performance. This manuscript aims to utilize Chiltan Limestone core samples to conduct a detailed analysis of the diagenetic impacts on reservoir quality. The formation evaluation was carried out through thin section analysis, SEM-EDS and FTIR investigation, as well as plug porosity and permeability measurements under different stress conditions. In results, Petrography revealed three microfacies with distinct diagenetic features and micro-nano fossil assemblages, including intraclasts, pelloids, bioclasts, and stylolites. Diagenesis has a significant impact on petrophysical properties, leading to increased reservoir heterogeneity. The specified depositional environment exposed the alteration of the Chiltan formation during distinct diagenetic phases in marine, meteoric, and burial settings. Pore morphology and mineralogy reveals complex micro-pore structure with various carbonate mineral phases and cement types in the formation samples. The average porosity and permeability of the core samples were found to be 3.4% and 0.449 mD respectively, indicating poor reservoir quality. Stress sensitivity was determined using Klinkenberg corrected permeability, which indicated a reduction in measured and absolute permeability due to increasing confining stress, further reducing the pore throat structure of the formation. In conclusion, the Chiltan formation possesses intricate reservoir heterogeneity and varied micro-pore structure caused by diagenesis and depositional settings. The formation is classified as a low-quality reservoir due to its non-uniform pore geometry, which exhibits low petrophysical properties resulting from overburden stress. The results of this study provide solid foundation in reservoir characterization and quality assessment which has implications for exploring and exploitation of indigenous resources.

Aluminum alloy Al 2024-T3 were successfully joined using friction stir spot jwelding joining (FSSW). Satisfactory joint strengths were obtained at different welding parameters (tool rotational speed, tool plunge depth, dwell time) and tool pin profile (straight cylindrical, triangular and tapered cylindrical). Resulting joints were welded with welded zone. The different tools significantly influenced the evolution on the stir zone in the welds. Lap-shear tests were carried out to find the weld strength. Weld cross section appearance observations were also done. The macrostructure shows that the welding parameters have a determinant effect on the weld strength (x: the nugget thickness, y: the thickness of the upper sheet and SZ: stir zone). The main fracture mode was pull out fracture modes in the tensile shear test of joints. The results of tensile shear tests showed that the tensile-shear load increased with increasing rotational speed in the shoulder penetration depth of 0.2 mm. Failure joints were obrerved in the weld high shoulder penetration depth and insufficient tool rotation.

The lack of knowledge on the link between the manufacturing process and performances constitutes a major issue of brake lining development. This study focuses on the effect of mixing duration on properties and tribological behavior of organic friction composite materials. The adopted methodology is based on efficient simplified formulations to limit synergic effects by the reduction of number and size distribution of constituents. Microstructural characteristics are analyzed and correlated to thermo physical and mechanical properties. Wear mechanisms and tribological behavior are studied in relation with the given microstructure and material properties. In the elaboration process, mixing duration has an impact on particle distribution and fibre arrangement. Distribution and size of fibre entanglements are found to cluster carbonaceous particles, which creates bulk thermal bridges improving thermal conductivity. Moreover, rockwool fibre arrangements affect density, porosity and thermo-physical properties. In addition, mixing duration disrupts cohesion of fibre bundles with the matrix, affecting compressive modulus and wear behaviour. This microstructural defect fosters an abundant third-body source flow, which results in a high wear flow. Porosities induced by fibre entanglements, presenting large and irregular size and distribution on the friction surface, lead to a low wear resistance and change the stability of friction.

The structural, elastic, anisotropic elastic, electronic, vibrational and properties of the Perovskite type Hydrides RbXH3 (X = Be, Ca, Mg) were performed via Vienna Ab – initio Simulation Pac-kage (VASP) based on Density Functional Theory (DFT). Our results have exhibited a well-agreement with previous calculations and experiments for each compound. In order to de-termine physical properties of RbXH3 has been used the Generalized Gradient Approximation (GGA) with Perdew-Burke-Ernzerhof (PBE) functional at this study. Present compounds were found to be mechanically stable as well as their gravimetric hydrogen storage capacities has been investigated. The Perovskite type Hydrides RbBeH3 and RbMgH3 has an indirect bandgap of 0.274 eV and 2.209 eV while RbCaH3 has a direct bandgap of 3.274 eV respectively and therefo-re these compounds has shown a semiconductor behaviour at equilibrium. Besides directional dependence of anisotropic properties was visualized by representing them with maximum - mi-nimum points..

In order to improve the performance of soft plantation wood, an environmentally friendly inorganic-organic hybrid wood modifier was developed. First, using urea and melamine as crosslinking agents, the waterborne glucose silicone resin (MUG) was prepared with glucose under the catalysis of inorganic acid and metal ions. Then MUG resin was diluted to 10% and 20% mass fraction, and compounded with sodium silicate (S) of 20% and 10% mass fraction, so the inorganic-organic hybrid G10S20 and G20S10 wood modifier were obtained respectively. Then plantation poplar wood (Populus tomentosa) were impregnated and modified with them. Their physical and mechanical properties were tested and compared with those of the wood treated with S of 20% mass fraction (S20). Infrared analysis showed that amino resin characteristic structure (CO-NH-) existed in MUG resin. The resin has good permeability. Compared with S20 modified wood, the degree of shrinkage of G10S20 or G20S10 modified wood is reduced, their moisture absorption is reduced, and their dimensional stability is improved. Waterborne glucose silicone modifier can effectively improve the wood density, modulus of elasticity, modulus of rapture and compression strength. SEM analysis showed that the cell wall of G20S10 modified wood was significantly thicker than the untreated wood, and there were columnar and granular solid substances attached in some cell cavities, ducts and corners, etc. EDX showed that the number of Si elements on the cell wall was significantly increased compared with the control, indicating that the modifier effectively entered the wood cell wall. The waterborne glucose silicone resin can greatly improve the physical and mechanical properties of wood through organic-inorganic hybridization. It is a green, non-formaldehyde, eco-friendly, low cost, compound wood modifier with broad application prospects.

Regional mechanics of the heart is vital in the development of accurate computational models for the pursuit of relevant therapies. Challenges related to heart dysfunctioning are the most important sources of mortality in the world. For example, myocardial infarction (MI) is the foremost killer in sub-Saharan African countries. Mechanical characterisation plays an important role in achieving accurate material behaviour. Material behaviour and constitutive modelling are essential for accurate development of computational models. In most cases previously, the mechanical properties of the heart myocardium were assumed to be homogeneous. The main objective of this paper is to determine the mechanical material properties of healthy porcine myocardium in three regions, namely left ventricle (LV), mid-wall/interventricular septum (MDW) and right ventricle (RV). The biomechanical properties of the pig heart RV, LV and MDW were characterised using biaxial testing. The biaxial tests show the pig heart myocardium behaves non-linearly, heterogeneously and anisotropically. In this study, it was shown that RV, LV and MDW may exhibit slightly different mechanical properties. Data presented here may be helpful in regional tissue mechanics, especially for the understanding of various heart diseases and development of new therapies.

Aluminum matrix nanocomposites have been the subject of much attention due to their extraordinary mechanical properties and thermal stability. This research focuses on producing and characterizing an aluminum matrix reinforced with silicon carbide (SiC) nanometric particles. The conventional powder metallurgy route was used to produce the nanocomposites, and the dispersion and mixing process was carried out by ultrasonication. The conditions of the dispersion and the volume fraction of the SiC were evaluated in the production of the nanocomposites. Microstructural characterization was carried out using optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD). Mechanical characterization was carried out using hardness and tensile tests. The dispersion agent was investigated, and isopropanol leads to better dispersion with fewer agglomerates. Increasing the volume fraction of the reinforcement improves the hardness of the nanocomposites. However, greater agglomeration of the reinforcement is observed for larger volume fractions. The greatest increase in hardness (77% increase compared to the hardness of the Al matrix) is obtained with 1.0 vol % of SiC, corresponding to the sample with the best dispersion. The mechanical characterization through tensile tests attests to the effect of the reinforcement on the Al matrix. The main strengthening mechanisms identified were the load transfer, the texture hardening, Orowan strengthening, and the increase in the density of dislocations in the nanocomposites.

Modification of Scots pine sapwood (Pinus sylvestris L.) with heterocyclic compounds, imidazole and succinimide, was investigated. Pressure-impregnation with aqueous solutions containing imidazole, imidazole + citric acid, succinimide, succinimide + citric acid, and citric acid + sorbitol (CIOL®) at 5%, 10%, and 15% solid content was followed by oven-curing at 220 °C for 1 hour. Mass changes during treatment steps, bending properties, and anti-swelling efficiency (ASE) were examined. Results indicate that solid concentrations within the range of 5% to 10% were optimal. Results seem to show there are two differing mechanisms in the modification of imidazole and succinimide, respectively. Mass loss due to the heat treatment was highest in imidazole-treated specimens, whereas it remained low and concentration-independent in succinimide-treated specimens. ASE after three cycles reached 31% for imidazole-treated specimens and improved to 38% with the addition of citric acid. For succinimide, ASE increased from 17% to 41%. Bending properties generally showed improvement, except for succinimide + citric acid and CIOL®, which displayed a reduced modulus of rupture. Chemical analyses are warranted to fully understand the reaction mechanisms of the treatments. Imidazole treatment's positive effects are suggested to stem from a thermal reaction between the chemical and wood, indicated by substantial mass loss during leaching and specimen darkening. Succinimide and citric acid might exhibit polymerization with each other and wood components, akin to the CIOL® process. Further research should delve into reaction mechanisms and the impact of imidazole and succinimide on biological durability.

: Dacarbazine, DAC, 5-(3,3-dimethyltriazeno)imidazol-4-carboxamideis is an imidazole-carboxamide derivative, that is structurally related to purines. DAC belongs to the triazene compounds, which are a group of alkylating agents with antitumour and mutagenic properties. DAC is a non-cell cycle specific drug, active on all phases of cellular cycle. In the frame of this work the 3d-metal complexes (cobalt and copper) with dacarbazine were synthesized. Their spectroscopic properties by the use of FT-IR, FT-Raman and 1HNMR were studied. The structures of dacarbazine and its complexes with copper(II) and cobalt(II) were calculated using DFT methods. The effect of metals on the electronic charge distribution of dacarbazine was discussed on the basis of calculated NBO atomic charges. The reactivity of metal complexes in relation to ligand alone was estimated on the basis of calculated energy of HOMO and LUMO orbitals. The aromaticity of imidazole ring in dacarbazine and the complexes was compared (on the basis of calculated geometric indices of aromaticity). Thermal stability of the investigated 3d-metal complexes with dacarbazine and the products of their thermal decomposition were analyzed.

The production of municipal solid waste incineration bottom ash (MSWIBA) is very massive and has the potential to replace cement despite the problems of complex composition, uneven particle size distribution, and low reactivity. This paper adopts sodium silicate activation of MSWIBA-slag to improve the reactivity to prepare composite cementitious materials. It explores the hydration performance study of the composite cementitious materials by isothermal calorimetric analysis, Fourier Transform Infrared (FTIR) spectroscopy, XRD physical diffraction analysis, and SEM/EDS tests. SEM/EDS tests will be used to explore the hydration properties of the composite gelling. The results showed that with the increase of MSWIBA doping, the porosity between the materials increased, the degree of Hydration decreased, and the compressive strength decreased with the rise of MSWIBA. When sodium silicate increased from 25% to 35%, too much alkaline material occurred over the alkaline effect, which inhibited the Hydration of the particles, and the degree of hydration reaction decreased, and the compressive strength decreased accordingly; the exothermic process of Hydration can be mainly divided into five stages, quartz and calcite did not participate in the hydration reaction completely, and sexual aluminum participated in the hydration reaction. The vibrational peaks of Si-O-Ti (T = Si and Al) were present in the material. The vibrational peaks of XRD, FTIR, and SEM-EDS all indicate the presence of silica-aluminate network structures in the hydration products, mainly N-A-S-H and C-A-S-H gels.

Epitaxial lithium ferrite (LiFe5O8) films with different thicknesses have been successfully fabricated on SrTiO3 (001) substrates by magnetron sputtering deposition technique. The microstructural and magnetic properties are characterized by advanced transmission electron microscope and magnetic measurement device. It was found that the formation of structural defects can be influenced by the thickness of the film. Apart from the misfit dislocations, the orientation domains form in thinner film and twin boundaries appear in thicker film, respectively, contributing to the misfit strain relaxation in the heterosystem. The magnetic measurement shows that the thinner films have enhanced magnetization and a relatively lower coercive field compared with the thicker films containing the antiferromagnetic twin boundaries. Our results provide a way for tuning the microstructure and magnetic properties of lithium ferrite films by changing the film thickness.

Herein, bamboo-laminated lumber for furniture was coated with waterborne acrylic paint. The effects of different painting techniques and quantities on the drying rate, smoothness, hardness, adhesion and wear resistance of the paint film were investigated. Then, the thermal properties of the paint were analysed using thermogravimetry and differential scanning calorimeter to examine the film-forming mechanism. The results showed that painting technique had no effect on the drying time, flatness, hardness and adhesion of the paint film, but it influenced the wear resistance. Herein, the films’ flatness showed little variation with different painting methods (one-layer primer one-layer topcoat, one-layer primer two-layer topcoat, two-layer primer one-layer topcoat and two-layer primer two-layer topcoat). The drying time for primer surfaces/solids was 8min/8.5 min, while it was 6.5/7 min for topcoats. The paint films exhibited grade B hardness and grade 0 adhesion and the better wear resistance when using one-layer primer one-layer topcoat at 51.24 mg·100 r−1. The amount of paint applied significantly affected the drying time and flatness of the paint film. As the quantity increased, the drying time of the paint’s surfaces and solids also increased, whereas the film’s flatness initially increased before decreasing. The film’s optimal adhesion, hardness and wear resistance values were grade 0, grade B and 51.24 mg·100 r−1, respectively, when 80 g/m2 of paint was applied. Thermal analysis of the primer and topcoat showed that water decomposition occurred at 100℃ and thermal decomposition of organic components occurred at 350℃. The primer and topcoat exhibited the same weight loss, but primer’s thermal loss rate was higher than that of topcoat. Consequently, the topcoat displayed better thermal stability than the primer.

In this study we assessed the electrical and optical behavior of semiconductor hybrid films fabricate from octaethyl-21H,23H-porphine copper (CuP), embedded in polymethylmethacrylate (PMMA), and polystyrene (PS). The hybrid films were characterized structurally and morphologically by means of Infrared spectroscopy (IR), atomic force microscopy (AFM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). Subsequently, the PMMA:CuP and PS:CuP hybrid films were evaluated optically by UV-vis spectroscopy, as well as electrically, with the four-point collinear method. Hybrid films present a homogeneous and low roughness morphology, besides; the PS matrix allows the crystallization of the porphin, while the PMMA promotes the amorphous structure in CuP. The polymeric matrix also has an effect on the optical behavior of the films, since the smallest optical gap (2.16 eV) and onset gap (1.89 eV) and the highest transparency are obtained in the film with a PMMA matrix. Finally, the electrical behavior in hybrid films is also affected by the matrix: the largest amount of current carried is around 0.01 A for PS:CuP film, while for PMMA:CuP film it is 0.0015 A. Thanks to the above properties, hybrid films are promising candidates for use in optoelectronic devices.

Once on Mars, maintenance and repair will be crucial for humans as supply chains including Earth andMars will be very complex. Consequently, the raw material available on mars must be processed and used. Factors such as the energy available for material production play just as important a role as the quality of the material that can be produced and the quality of its surface. With the aim of developing and technically implementing a process chain that meets the challenge of producing spare parts from oxygen-reduced Mars regolith, this paper addresses the issue of low-energy handling. Expected statistically distributed high roughnesses of sintered regolith analogs are approximated in this work by parameter variation in the PBF-LB/M process. For low-energy handling, a dry-adhesive microstructure is used. Investigations are carried out to determine the extent to which the rough surface resulting from the manufacturing process can be smoothed by deep rolling in such a way that the microstructure adheres and enables samples to be transported. For the investigated AlSi10Mg samples (12 mm x 12 mm x 10 mm), the surface roughness varies in a wide range from Sa 7.7 µm to Sa 64 µm after the additive manufacturing process, pull-off stresses of up to 6.99 N/cm² could be realized after deep rolling. This represents an increase in pull-off stresses by a factor of 392.94 compared to the pull-off stresses before deep rolling, enabling handling of even larger specimens. It is noteworthy that specimens with roughness values that were previously difficult to handle can be treated post-deep rolling, indicating a potential influence of additional variables that describe roughness or ripples and are associated with the adhesion effect of the microstructure of the dry adhesive.

This study focuses on the development and characterization of a series of six new dansyl derivatives (L1 to L6) and their integration into PMMA polymers for application in environmental sensing. The photophysical properties of these derivatives were extensively studied in various solvents and in solid state. A remarkable positive solvatochromic effect was observed, indicating their potential in microenvironmental polarity assessment. The dansyl derivatives demonstrated selective sensing capabilities for Cu2+ and Hg2+ metal ions, with the formation of mononuclear species. Additionally, their acid-base responsive nature was explored, revealing potential for pH-sensitive applications. The incorporation of these derivatives into PMMA polymers resulted in acid-base sensitive materials suitable for environmental monitoring, particularly in detecting hazardous gases and changes in pH levels. This integration overcomes the solubility limitations of dansyl compounds and extends their applicability in diverse sensing scenarios.

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

The health benefits of extra virgin olive oil (EVOO) are related with its chemical composition and the presence of bioactive compounds with antioxidant properties. The aim of this study was evaluate antioxidant compounds (pigments, CoQ10 and phenolic compounds) and antioxidant properties of EVOO from the same region comparing different cultivars (Hojiblanca and Arbequina), harvest year and crop stage. Antioxidant properties of oils were studied before and after a gastrointestinal digestion process, by in vitro assays (DPPH, ABTS and FRAP) and antioxidant markers in Caco-2 cells (reactive oxygen species production). The content of bioactive compounds measured was significantly affected by cultivar and harvest year (except for carotenoids) and by the crop stage (except for coenzyme Q10). Higher amount of coenzyme Q10 was observed in Hojiblanca than in Arbequina EVOO. Total phenol content and antioxidant properties were also different depending on cultivar and harvest year and the in vitro digestion process strongly improved antioxidant marker values. Antioxidant potential in bioaccessible fractions was mainly related with content of coenzyme Q10 and phenolic compounds in EVOO. Chemometric analysis showed that the oils were clearly classified by cultivars, harvest and crop stage, according with chemical composition and antioxidant activity analyzed in the present study

The production of biomass fly ash has been increasing every year in Europe, reaching 5.5 million tons in 2020. Biomass fly ash is not yet accepted in the standards as a substitute material for cement in mortar and concrete. In a first approach, the substitution limit of biomass fly ash is determined by comparing the mechanical strengths, fresh state properties and hardened properties of mortars produced with biomass fly ash to those of mortars produced with classical coal fly ash. Then, masonry and rendering mortars have been designed with different substitution rates of biomass fly ashes from wood combustion in thermal power plant. Although there is an overall decrease in performance, mortars made with biomass ash retain properties that make them suitable for use in masonry or rendering.

Biomimetic materials are substances that replicate natural structures. There are several methods for producing such materials with highly developed surfaces from a wide range of polymers, but electrospinning is of particular interest due to its simplicity of implementation and the ability to modify the produced fibrous materials resembling structures found in living organisms. This study explores new biomimetic materials based on polyhydroxyalkanoates, specifically poly-3-hydroxybutyrate, modified with chlorophyll derivatives. The research investigates the impact of chlorophyll derivatives on the morphology, supramolecular structure, and key properties of nonwoven materials. The obtained results are of interest for the development of new biomimetic environmentally friendly materials for biomedicine with special properties.

Photophysical properties of a series of bis(arylydene)cycloalkanone dyes with various donor substituentns are studied by quantum chemistry. Their capacity for luminescence and nonradiative relaxation through trans-cis isomerization is related to their structure, in particular, to the donor capacity of the substituents and the degree of conjugation due to the central cycloalkanone moiety. It is shown that cyclohexanone central moiety introduces distortions and disrupts the conjugation, thus leading to a nonmonotonic change in their properties. The increasing donor capacity of the substituents causes increase in the HOMO energy (raise of the oxidation potential) and decrease in the HOMO-LUMO gap, which results in the red shift of the absorption spectra. The ability of the excited dye to relax through fluorescence or through trans-cis isomerization is governed by the height of the barrier between the Franck–Condon and S1-S0 conical intersection regions on the potential energy surface of the lowest π-π* excited state. This barrier also correlates with the donor capacity of the substituents and the degree of conjugation between the central and donor moieties. The calculated fluorescence and trans-cis isomerization rates are in good agreement with the observed fluorescence quantum yields.

The interest in obtaining new composite materials with diverse properties has created a growing interest in natural fi-bers as reinforcement in polymers, which has generated an impact in sectors such as automotive and construction, dis-placing synthetic fibers. Properties such as low density, low cost, and rene.wable make these fibers an attractive alterna-tive to reduce environmental impact. Their application in polymers, such as polypropylene, polyethylene, and epoxy resins, has allowed the modification of polymeric composite materials' mechanical and physical properties (NFRP). This review focuses on investigating the status of natural fiber-reinforced polymers. It analyzes their worldwide demand, chemical characteristics, physical and mechanical properties, and various applications in different sectors and indus-tries. In addition, the advantages and disadvantages of NFRPs are highlighted, highlighting their potential for new ap-plications.

In the present work, diamond films have been grown on GaN-on-Sapphire substrates by chemical vapor deposition (CVD) with the addition of nitrogen to the standard H2/CH4 precursor recipe. Diamond on GaN materials processing is not straight-forward, as GaN is susceptible to a quasi-pure hydrogen CVD plasma etching. 1%, 3% and 5% N2 gas was gradually added to the H2 gas with fixed 6% CH4 in the recipe to promote the growth of diamond nanocrystals. Different types of microstructures were produced, with addition of nitrogen to the precursor gas recipe. Nitrogen gas changes the diamond film microstructure from faceted to spherical grains, with signs of GaN etching. The sp3 bonded diamond film produced by nitrogen addition was found to be co-deposited along with a considerable amount of other non-diamond carbon phases (D - disordered graphite, G - crystalline graphite, TPA - trans-polyacetylene) and qualitatively all the diamond films were 50% pure (Raman peak ratio Isp3 / ID). The FWHM of the sp3 carbon Raman peak was calculated to be 6.5 cm-1, when there was no nitrogen gas in the precursor recipe, which deteriorates to a large extent after successive addition of N2. Fourier transform infrared spectroscopy (FTIR) showed a strong presence of the nitrogen related defects (peak positions at 1190 and 1299 cm-1) inside the nanocrystalline diamond (NCD) films grown with N2 addition. GaN layer etching from the base substrate by the CVD plasma was clearly evidenced by energy dispersive X-ray spectra (EDS) of the deposited films. Al elemental EDS peaks from the base sapphire substrate were observed for the films grown with nitrogen addition, but no Ga EDS peaks were detected. X-ray diffraction (XRD) micrographs further supported the enhanced GaN etching phenomenon. Nitrogen addition was thus found to be detrimental for growing CVD diamond films over GaN surfaces. The electrical resistivity of the uncoated GaN was initially measured to be 22.2 Ω-cm. However, the resistivity rose to 1.59×106 Ω-cm after the nitrogen assisted film deposition; due to the GaN etching - thereby exposing the underlying insulating sapphire substrate.

Background: The Perceived Inventory of Technological Competency as Caring in Nursing (PITCCN) questionnaire has been designed to measure technological competency as caring in nursing practice. As there were no psychometrically sound instruments to quantify the concept in the Slovene language. The goal was to assess the level of psychometric properties of the PITCCN investigated in Slovene hospitals. Methods: Content validity was conducted with eight experts and quantified by the content validity index (CVI) and the modified Cohen’s kappa index. Face validity was assessed through discussions with participants from the target culture in the pilot study. To assess construct validity and internal consistency, a cross-sectional research methodology was used on a convenience sample of 121 nursing personnel from four hospitals. Principal component analysis (PCA) was used to examine construct validity, while Cronbach’s alpha and adjusted item-total correlations were used to measure internal consistency. Results: The content and face validity of PITCCN were adequate. The scale validity index (S-CVI) was 0.97. Cronbach’s α was 0.92, and subscale reliabilities ranged from 0.810 to 0.925. PCA showed four components, which explained more than 73.49% of the variance. Conclusions: The Slovenian version of PITCCN (PITCCN_SI) has good psychometric properties.

The Individual Work Performance Questionnaire (IWPQ) can be defined as the individual be-haviour capable of generating value and competitive advantage for the organization. It is a mul-ti-dimensional construct, consisting of task performance, contextual performance and counter-productive work behavior. Albeit important, a comprehensive measure of individual job per-formance is still lacking in the Italian context. This paper describes the validation of an Italian adaptation of the IWPQ. A back translation procedure was used. To investigate the psychometric properties of the 18-item Italian IWPQ, 1053 participants (502 men, 47.7%; 551 women, 52.3%) were enrolled; the age of participants ranged between 19 and 69 (Mage=34.6, SD= 11.8), and for the oc-cupation, the sample is classified in blue collar 32.5%, pink collar 33% and white collar 34.5%. Exploratory and confirmatory factor analyses and multigroup confirmatory factor analyses were performed to test the structural factor of the IWPQ. The results supported the goodness of the IWPQ in the Italian context and the scales were found consistent with the original structure. One item was omitted due to a low factor loading, resulting in a final 17-item structure. Multigroup confirmatory factor analysis showed that the factor solution was invariant across both gender and occupational category and found evidence of metric invariance, uniqueness and scalar invariance, and structural invariance. Convergent and discriminant validity were also tested and showed.

In the aerospace sector, structural and non-structural components are usually subjected to a wide range of environmental conditions. Although lightweight, the use of composite parts for these applications is restricted, due to their poor performance in severe environmental conditions. Specifically, moisture can seriously damage the materials' performance, reducing their mechan-ical, thermal, electrical, and physical properties as well as the service time. A strategy to improve the materials’ resistance in humid environments is the use of protective lightweight barrier coatings to reduce the diffusion of gases and/or liquids in composites. Nanolamellar nanocom-posite characterized by the high in-plane orientation of nanoplatelets effectively works as barrier structures by generating tortuous paths for molecule diffusion. In this work, the effectiveness of protection against water uptake of nanocomposites reinforced with Graphite NanoPlatelets (GNPs) at high filler content (70, 80 and 90%wt) for Kevlar sandwich panels of a nacelle engine of an ATR42 aircraft has been investigated. Moisture uptake and Ground Air Ground (GAG) tests were carried out in an environmental chamber to reproduce temperature and relative humidity profiles representative of a real-scale application for a regional aircraft composite part. The high filler content of the graphene films ensures a high level of tortuosity by delaying and reducing moisture absorption by –71% compared to the unprotected panel, showing good barrier properties.

The main goal of this study was to introduce glycerol as a plasticizer to Polyvinyl Alcohol (PVA) membranes in order to increase their flexibility. The qualities of PVA membranes produced with various glycerol concentrations were evaluated. With the modified PVA membranes containing 5% glycerol, encouraging results were obtained. These membranes had superb optical characteristics and a 90% transmittance rate. This shows that the membranes are suited for applications needing excellent optical clarity since they permit light to travel through with little distortion. Importantly, FTIR analysis demonstrated that the addition of glycerol had no effect on the PVA membranes' chemical composition or structural integrity. In comparison to pure PVA Membrane, the modified membranes' water barrier qualities showed a considerable drop of up to 50%. The membranes are useful for applications requiring moisture management or breathability because of the decline, which points to an increase in permeability to water vapour. The large increase in flexibility, which was achieved by the PVA membranes containing 5% glycerol and beyond the brittleness typically associated with pure PVA, was a noteworthy discovery. The possible applications are expanded due to the increased flexibility, especially in industries where adaptability and flexibility are essential. Additionally, the addition of glycerol improved the thermal stability of the membranes, as they showed increased resistance to breakdown or decomposition at high temperatures. Additionally, the modified membranes' mechanical qualities were better than those of pure PVA, indicating that the glycerol addition improved their overall mechanical performance and tensile strength. PVA membranes were effectively made more flexible by adding 5% glycerol as a plasticizer. This led to membranes with superior optical qualities, reduced water barrier properties, greater flexibility, improved thermal stability, and maybe improved mechanical capabilities. These discoveries open up new opportunities for the use of these flexible PVA membranes in a range of settings, such as flexible packaging, biomedical materials, and other industries that need adaptive and flexible materials.

The temperature-dependent energy storage properties of four tungsten bronze phase compounds are studied together with an investigation of their structure and temperature-dependent permittivity response, i.e., Ba6Ti2Nb8O30 (BTN), Ba6Zr2Nb8O30 (BZN), Sr3TiNb4O15 (STN) and Sr3ZrNb4O15 (SZN) ceramics. It was found that BZN has smaller grains and a more porous structure than BTN. SZN shows no clear grain boundaries with the most porous structure among all samples, exhibiting a much lower permittivity response than other samples with no signs of phase transitions from room temperature to 400 °C. Though the energy storage response of those samples is generally quite low, it exhibits rather good temperature stability. It was suggested that by obtaining a denser structure through chemical modification or other methods, those tungsten bronze ceramics with good temperature stability could be promising as energy storage devices when improved energy storage properties are achieved.

Deformation behavior of the composite "hen's eggshell - polymer plomb" under bending is examined. Polymer coating does not change the type of behavior of the composite based on eggshell that continues to be brittle despite the mechanical characteristics of the composite could vary in wide limits for brittle structure. Joining "hen's eggshell – polymer plomb" never crack under loading and, hence, it exhibits the high cohesion strength under stresses applied in these experiments. It seems that the composite "hen's eggshell - polymer plomb" could apply as the substitution of the composite "tooth enamel - polymer plomb" under elaboration of novel restorative materials for dentistry, namely, for estimation of their mechanical properties including cohesive strength.

The study of the inherent factors that influence the isolation of one type of metallosupramolecular architecture over another is one of the main objectives in the field of Metallosupramolecular Chemistry. In this work, we report two new neutral copper(II) helicates, [Cu2(L1)2]·4CH3CN and [Cu2(L2)2]·CH3CN, obtained by means of an electrochemical methodology and derived from two Schiff-based strands functionalized with ortho- and para-t-butyl groups on the aromatic surface. These small modifications let us to explore the relationship between the ligand design and the structure of the extended metallosupramolecular architecture. The magnetic properties of the Cu(II) helicates were explored by EPR spectroscopy and DC magnetic susceptibility measurements.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

PurposeThis study was designed to characterize the psychometric properties of the Persian version of the Fear of Hospitalization Scale (P-FHS).Design and methodsIn order to evaluate the validity and reliability of the translated scale, a cross-sectional design was employed. Ten experts evaluated the content validity of the Fear of Hospitalization Scale (FHS) after it had been back-translated into Persian. With 612 patients having emergency surgery, construct validity was assessed using exploratory factor analysis (EFA) and confirmatory factor analysis (CFA). The STROBE checklist for cross-sectional studies was followed.FindingsThe results of EFA (n = 306) showed that the fear of hospitalization had three factors. These three factors accounted for 45.28% of the total variance. Also, these factors were confirmed by CFA (n = 306) (root-mean-square error of approximation = (90%. confidence interval) = 0.050 [0.041, 0.058], goodness-of-fit index = 0.945, comparative fit index = 0.968, Non-Normal Fit Index = 0.948, incremental fit index = 0.968, Tucker-Lewis Index = 0.959). The coefficients of Cronbach’s alpha, McDonald’s omega, composite reliability, and maximum reliability for all three factors were greater than 0.7, demonstrating satisfied internal consistency.Practice implicationAccording to the published results, the P-FHS is effective at measuring hospitalization anxiety in patients undergoing emergency surgery. It is advised that nurses in Iranian culture use a legitimate and trustworthy technique to pinpoint the causes of hospitalization anxiety in patients undergoing emergency surgery to give optimal care.

Usually in the manufacture of beer by fermentation of barley, in both industrialized and developing countries significant amounts of organic solid waste are produced from barley straw. These possibly have an impact on the carbon footprint with an effect on global warming. According to this, it is important to reduce environmental impact of these solid residues, and an adequate way is the recycling using them as raw material for the elaboration of handmade paper. Therefore, it is required to manage this type of waste by analyzing the environmental impact, and thus be able to identify sustainable practices for the treatment of this food waste, evaluating its life cycle, which is a useful methodology to estimate said environmental impacts. It is because of this work shows the main results obtained using the life cycle analysis (LCA) methodology, to evaluate the possible environmental impacts during the waste treatment of a brewery located in the state of Hidalgo, Mexico. The residues evaluated were barley straw, malt residues and spent grain, and at the end, barley straw was selected to determine in detail its environmental impact and its reuse, the sheets analyzed presented a grammage that varies from 66 g/m2 and 143 g/m2, resistance to burst was 117 to 145 kpa, with a crystallinity of 34.4% to 37.1%.

The thermal properties of novel nanomaterials play a significant role in determining the performance of the material in technological applications. Herein, direct measurement of the temperature diffusivity of cellulose nanocomposite films was carried out by the micro-contact method. Polymer films containing up to 2%wt. of nanocellulose were synthesised by a simple chemical process. Films of a high optical transmittance T ≈ 80 % (for a 200- μ m-thick film), which were up to 44% crystalline, were characterised. Two different modalities of temperature diffusivity based on: 1) a resistance change and 2) micro-thermocouple detected modulation of a heat wave, were used for the polymer films with cross-sections of ∼ 100 μ m thickness. Twice different in-plane α ‖ and out-of-plane α ⊥ temperature diffusivities were directly determined with high fidelity: α ‖ = 2 . 12 × 10 − 7 m 2 /s and α ⊥ = 1 . 13 × 10 − 7 m 2 /s. An amorphous polyethylene terephthalate (PET) fiber was measured for comparison α ‖ = 1 . 15 × 10 − 7 m 2 /s. This work provides an example of a direct contact measurement of thermal properties of nanocellulose composite films. The thermal diffusivity, which is usually high in strongly interconnected networks and crystals, was investigated for the first time in this composite.

In-situ grown C_0.3N_0.7Ti and SiC, which derived from non-oxide additives Ti₃SiC₂, are proposed to densify silicon nitride (Si₃N₄) ceramics with enhanced mechanical performance. Remarkable increase of density from 79.20% to 95.48% could be achieved for Si₃N₄ ceramics with 5vol% Ti₃SiC₂. The capillarity of decomposed Si from Ti₃SiC₂, and in-situ reaction between nonstoichiometric TiC_x and Si₃N₄ were believed to be responsible for densification of Si₃N₄ ceramics. An obvious enhancement of flexural strength and fracture toughness for Ti₃SiC₂ doped Si₃N₄ ceramics was observed. The maximum flexural strength of 795 MPa for Si₃N₄ composites with 5vol% Ti₃SiC₂ and maximum fracture toughness of 6.97 MPa^.m^1/2 for Si₃N₄ composites with 20vol% Ti₃SiC₂ are achieved when mixed powders are hot-press sintered at 1700℃. Pull out of elongated Si₃N₄ grains, crack bridging, crack branching and crack deflection were demonstrated to dominate enhance fracture toughness of Si₃N₄ composites.

Even if silicon alkoxides (especially ethylsilicates) have long been used as consolidants of weathered stone monuments, their physical properties are not ideal. In this study, an innovative procedure for the consolidation of sedimentary rocks was developed that combines the use of organometallic and alkylamine catalysts with the addition of well-defined nanoparticles exhibiting a narrow size distribution centered at ca 10 nm. As a suitable test material, the Pietra di Lecce limestone was selected because of its color and problematic physico-chemical properties, such as rather low hardness. Using the developed procedure, the mechanical and surface properties of the limestone were improved without the unwanted over-consolidation of the surface layers of the stone, and any significant deterioration in the pore size distribution, water vapor permeability or the stone’s appearance. The developed modified ethylsilicates penetrated deeper into the pore structure of the stone than the unmodified ones and increased the hardness of the treated material. The formed xerogels within the stone pores did not crack. Importantly, they did not significantly alter the natural characteristics of the stone.

Nanofibers appearing functional properties show a great promise as allowing constituents for a wide range of medical applications. In this work, Polycaprolactone (PCL), Silver Nitrate (AgNO₃) and Zinc Oxide (ZnO) were used for fabrication of nanofiber composite material by co-axial electrospinning (CAE) process. 5, 10, and 15 wt. % concentrations of PCL were utilized and different amount of AgNO₃ and ZnO were used in entire samples. Morphological analyses of the electrospun nanocomposites were done by scanning electron microscopy (SEM) and AgNO₃, ZnO and PCL materials’ functional groups were determined by Fourier Transform Infrared Spectroscopy (FTIR). Before co-axial electrospinning, physical properties such as liquid state ac conductivity, density and viscosity were measured for all solutions. Capacitance (C_p) and D-factors (tanδ) of nanocomposite materials are measured for the frequency range of 20Hz – 3MHz and the solid state alternating current (ac) conductivity, permittivity (ε’) and dielectric loss (ε’’) were calculated for all solutions after co-axial electrospinning. Effects of concentration percentages of PCL and AgNO₃ on real and imaginary parts of dielectric constant and solid state ac conductivity have been analyzed and comparisons have been made by the results obtained.

Considering the significant interest in the synthesis and various properties of the polymorphs of tin dioxide (SnO2), they are still comparatively rare in modern photovoltaic techniques. The hybrid organic-inorganic lead perovskites have triggered a revolution among solar cell researchers due to their low cost and ultrahigh power conversion efficiency. In this research, the optical properties of seven stable polymorphs (Balakrishnan Kanimozhi et al. ACS omega 7, 12 (2022): 10382-10393) of SnO2 have been investigated using first-principles approaches. The effective mass of stable SnO2 polymorphs has been computed and it is found to vary depending on the specific polymorph and the direction in which it is measured. Moreover, the spectroscopic limited maximum efficiency (SLME) of SnO2 polymorphs was also computed and compared to that of other efficient perovskite solar cells. Both Pnnm and Pbca have equivalent efficiency in comparison to the rutile polymorph. Three of the seven stable polymorphs are effective in solar cell applications. This study is the very first attempt to examine the atomic structure and electronic properties of various SnO2 polymorphs using X-ray absorption near-edge spectroscopy (XANES) at both the Sn-K-edge and O-K-edge wavelengths. Our findings, as mentioned in this paper, may be an important advancement in the understanding of these materials, thereby facilitating the development of more efficient photovoltaic devices.

Undisturbed ground temperature (UGT), thermal conductivity (TC) and heat capacity (HC) are essential parameters for the design of borehole heat exchanger (BHE) and borehole thermal energy storage systems. However, field methods to assess the thermal state and properties of the sub-surface are costly and time consuming. Moreover, HC is often not evaluated but arbitrarily selected from literature considering the geological materials intercepted by boreholes. Therefore, this work aims at proposing a field heat tracing method to infer the thermal diffusivity (TD) and HC with assumption of natural transient heat conduction in the subsurface. Empirical equations were developed to reproduce a UGT profile measured along a BHE. Experimental coefficients are found with a non-linear least square solver optimization and used to calculate the damping depth and TD. Subsequently, the TD is used to evaluate HC considering TC obtained from a thermal response test (TRT). Results from this proposed heat tracing method were verified and validated against a set of TRT results and oscillatory TRT analysis using a field dual probe concept to infer HC. The example here described highlights the advantages and novelty of this fast and simple field method relying only on a single UGT profile measured before a TRT.

Direct interaction with the neuronal cells is a prerequisite to deciphering useful information in understanding the underlying causes of diseases and functional abnormalities in the brain. Precisely fabricated nanoelectrodes provide the capability to interact with the brain in its natural habitat without compromising its functional integrity. Considerable research has been focused on the employment of vertical nanotubes as nanoelectrodes due to large-scale intracellular recording capability and longer-term intracellular access that arise from their unique geometry. Despite many types of nanotube structures reported in the literature, a limited subset of the nanotubes has been investigated for neural interfacing. This work reports on the fabrication and optimisation of vertically oriented titania nanotube arrays as a scalable electrode platform for neural interface application. To this end, the doping was performed by incorporating a selected group of biologically active metallic ions, including zinc, strontium, and copper, into TiO2 lattice and its effect was studied with respect to the structural, electrochemical and biological properties of the nanotube arrays. It was found that doping can change the length, diameter and wall thickness of the nanotubes. Among pure and doped samples, the copper-doped TiO2 nanotubes demonstrated the highest electrochemical and biological performance. Our results suggest that the doping can be used as a promising method to optimise the properties of nanotube arrays for the development of high-performance neural electrodes.

Molecular and morphological properties of poly(vinyl chloride) grains produced by suspension polymerization of VCM in the presence of a mixture of three kind of initiators (i.e. fast, mild and slow) (named as Cok process) was experimentally investigated in a pilot-scale reactor. The results obtained here were initially compared with a isothermal regular process (named as control process) and then with those obtained already for other productivity-enhancing polymerization techniques (i.e. nonisothermal and fast initiator dosage process). The results showed that, in contrast to nonisothermal and fast initiator dosage process, the addition of initators mixture at the beginning of the reaction has the smallest influence on molecular weight and polydispersity index compared to control process. It is obvioused that Cok-PVC grains have the lowest cold plasticizer absorption and porosity among these mentioned processes. Scanning electron microscopy (SEM) showed that the particles produced by Cok process are more regularly shaped, with a smoother surface compared with the control product. According to the literatures, all three productivity-enhancing techniques lead to an apparent quality enhancement, higher flowability and greater bulk density of final grains. While both processes of continous initiator dosage and nonisothermal polymerization broaden the particle size distribution of final PVC grains, applying initiator mixture produces particles with the same particle size distribution as control process. The SEM images processing showed that Cok process deccelerates the formation of a three-dimensional skeleton of primary particles relative to the control polymerization. In comparison with nonisothermal trajectory and continous fast initiator dosage system, the Cok polymerization process leads to the most delay of motionless conversions and fusion time as well.

New complexes of manganese(II) hexafluoroacetylacetonate [Mn(hfac)2] with 2-(1-R-3-pyrazol-4-yl)-4,4,5,5-tetramethyl-2-imidazoline-3-oxide-1-oxyl (R = CHF2, CH2CH2F, CH2CHF2 or CH2CF3) were synthesised and characterised structurally and magnetically. All complexes were prepared under similar conditions. Nonetheless, their crystal structures were considerably different. Depending on the structure of fluorinated alkyl substituent R, the complexation reaction led to complexes of three types: chain-polymeric complexes with the head-to-head or head-to-tail motif and complexes of molecular structure. All complexes show strong antiferromagnetic behaviour in a high-temperature region (150−300 K) and weak ferro- or antiferromagnetic exchange interactions at low temperatures. The stronger antiferromagnetic exchange, –101.7 ± 1.5 or –136 ± 10 cm–1, –82.3 ± 1.3 cm–1 and –87.4 ± 1.3 cm–1, was attributed to the magnetic interaction in three- or two-spin clusters: {&gt;N∸O–Mn2+–O∸N&lt;} or {&gt;N∸O–Mn2+}, respectively. The weaker antiferromagnetic interaction, –0.005, between three-spin clusters or ferromagnetic interactions, 0.18–0.81 cm–1, between two-spin clusters are realised through the pyrazole ring or intermolecular contacts.

The phosphogypsum (PG) pile of solid waste is of immense proportions and poses a grave threat to the ecological environment, with its reserves steadily increasing year after year. The urgent need for large-scale consumption and high-quality utilization of PG in industrial production has become apparent. The present study provides a comprehensive analysis of the correlation be-tween the macroscopic mechanical properties and microstructure of PG, elucidating the crystal morphology characteristics in different phases and outlining the crystallization preparation pro-cess. By integrating the physical and chemical properties of diverse PG phases with the intricacies associated with its preparation process, it is imperative to explore avenues for its high-value utili-zation, investigate possibilities for industrial-scale production, and analyze and predict the appli-cation trends and developmental directions in comprehensive PG utilization. These endeavors hold immense significance in guiding the realization of resource utilization potential inherent in PG.

Surfactants are amphiphilic molecules and one of the most versatile products of the chemical industry. They can be absorbed at the air-water interface and can align themselves so that the hydrophobic part is in the air while the hydrophilic part is in water. This alignment lowers the surface or interfacial tension. Gemini surfactants are a modern variety of surfactants with unique properties and a very wide range of potential applications. Hexamethylene-1,6-bis(N-dodecyl-N,N-dimethylammonium bromide) is one such representative compound that is a better alternative to a single analogue. It shows excellent surface, antimicrobial, and anticorrosion properties. With a highly efficient synthetic method and a good ecological profile, it is a potential candidate for numerous applications, including biomedical applications.

Polylactic acid (PLA) was modified with three types of MVOs, which are the epoxidized soybean oil (ESBO), maleinized sunflower oil (MSO) and maleinized olive oil (MOO), at different weight fractions. A co-rotating twin screw extruder was used to produce composite materials by melt mixing process. The effect of MVOs content, from 2.5% to 10%, on the morphology, mechanical properties, density and water absorption were investigated in detail. Addition of ESBO and maleinized vegetable oils leads to a slight decrease in density of PLA from 1.252 to 1.231 g/cm3. As the concentration of MVO in PLA increases, the amount of water absorption also increased and the highest water absorption value was observed in P10MSO. In general, the elastic modulus (EM) was slightly changed by the addition of MVO to PLA, while the tensile strength (TS) decreased. Due to the plasticizing effect of MVOs, an increase in the Izod impact strength was obtained.

Starch is a biopolymer with wide potential for the generation of new biodegradable packages due to its high availability and low price. However, due to its weak functional properties, it is necessary to limit the interaction of some hydroxyl, and to evaluate blends with other polymers to improve their performance. Glycerol plasticized acetylated corn starch films were developed by the casting method, and the impact of incorporating chitosan (TPS:CH) at various proportions (75:25, 50:50, and 25:75 v/v) was studied. The effect of the chitosan ratios on the films' physical, mechanical, water vapor barrier, and thermal properties was evaluated. Chitosan protonated amino groups promote the formation of intermolecular bonds, improving the tensile strength, the thermal stability, the water adsorption capacity, and the gas barrier of starch films. Where the film composed of TPS25-CH75 was the one that presented the best barrier to water vapor. These composite films are a good option for development of biodegradable packaging.

ZnS-CdS composite nano-powder doped with (0.01 mol %) Cobalt has been collected by a co-precipitation process at 300 K. The sample is characterized by structural, combined spectroscopic methods and magnetic studies. The prepared samples were belonging to cubic structure no impurity phases were observed. Doping of cobalt increase the neighborhood strain assessment and a decreases lattice constants decides from x-ray diffraction data. The crystallite size is 10.42nm. From UV-absorption and EPR studies revealed that the energy band gap of Co2+ doped ZnS-CdS composite nanopowder and extension of sp-d exchange interactions and common d-d transitions. The variation in the energy bandgap varies as a function of cobalt concentration is due to structural modification. Photoluminescence spectrum reveals the defect-related emissions and shows the formation of luminescence. FT-IR spectrum confirmed the feature vibrational manner of Zn, Cd, O–H and sulfide ions are in the host lattice. The doping-induced magnetic properties are studied by vibrating sample magnetometer which matches with the theoretical values besides ferromagnetic nature. Magnetic studies confirm the ferromagnetic nature of the material. Surface morphology and chemical homogeneity studies were carried out by using SEM with EDAX. Transmission electron microscope recommends the crystalline nature of nanoparticles, with average particle size is of the order of 20-100nm.

The present study evaluates the psychometric properties of the Conflicts in Romantic Relationships Over Facebook Use Scale with a sample of Puerto Rican adults. A total of 577 Puerto Ricans participated on this confirmatory and psychometric study. The results confirmed that the scale has a multidimensional structure. These dimensions are: Partner Facebook intrusion, Conflict over Facebook use, and Jealousy over Facebook use. A total of 18 items complied with the criteria of discrimination and presented appropriate factorial loads (6 items per dimension). The Cronbach’s Alpha indexes of the dimensions ranged between .87 and .95 and the omega coefficients ranged between .88 and .95. In summary, the instrument has the appropriate psychometric properties to continue with validation studies, as well as to be implemented in various work areas, both theoretical and applied.

The shear factor of ore drawing is one of the important factors affecting the formation of underground debris flow, and it has an important contribution to the formation of underground debris flow. The purpose of this paper is to study the effect of mining shear factor on underground debris flow in natural caving method. Based on the research background of the underground debris flow in Plan copper mine, this paper analyzes the characteristics of the slurry material structure of the underground debris flow, the influence of drawing shear factor on formation mechanism of underground debris flow is analyzed. The results show that the slurry of the underground debris flow in Plan mine is not only a pseudoplastic fluid but also a thixotropic fluid. It is indicated that once there is shearing force in drawing, it will deform, and its viscosity will decrease with the increase of shear rate and time. It is considered that the shear force produced by the flow of ore particles first produces shear action on the paste in the shear boundary region of ore drawing, it is reduced in viscosity and increased in fluidity, so that its “Activation” and then become a flowable paste, along with the bulk ore flow through the mouth. The continuous ore drawing process will continuously shear the new moraine slurry in the ore drawing channel and continuously “Activate” the moraine slurry in the ore drawing channel, finally, a certain scale and destructive down-hole debris flow accident. This paper is the first to study the effect of ore drawing shear factor on the formation mechanism of underground debris flow. It not only broadens the research field of debris flow, but also fills up the deficiency of systematic research on underground debris flow, and provides theoretical guidance for the prevention and control of underground debris flow.

Many historic buildings and monuments on the Salento Peninsula (Apulia, southern Italy) were built from locally quarried Miocene calcarenites belonging to the Pietra Leccese Formation (Late Burdigalian-early Messinian). The main facies consists of a homogeneous and porous biomicrite, pale yellow in color and fine- to medium-grained, very rich in planktonic Foraminifera and massive or thick-bedded in outcrop. Additionally, there are other facies among which Piromafo stands out for its aesthetic appearance, which is enhanced by its greenish-brown or greenish-grey colors. Its physical characteristics, in terms of thermal properties mainly due to the mineral content and fabric, make it a good refractory and insulation material. Piromafo occurs in the upper part of the Pietra Leccese Fm. and is repre-sented by a fine- to medium-grained glauconitic and phosphatic biomicrite with macrofossils, es-pecially Bivalves and Gastropods. Despite its important historical use as building and ornamental material, especially in the Roman and Baroque architecture, a research gap exists in the scientific literature describing the properties of the stone and their correlation. Therefore, the aim of this paper is to present a wide range of properties useful to explain the in-situ behavior and damage susceptibility of the stone in monu-ments and buildings, but also for selecting preservation treatments and strategies. Thus, an overall assessment of the main petrophysical and mechanical properties especially for restoration/conservation purposes was performed using both standard and unconventional tech-niques. Starting from rock fabric inspection, particular attention was given to the relationship be-tween pore-size distribution and, hydraulic and thermal properties of the material. Unconfined compressive strength, flexural strength and indirect tensile strength were also estimated.

Fast-growing teak is widely cultivated in Indonesia to address the supply and demand of teak trees. However, efforts still need to be made to evaluate the condition of standing teak trees during their growth period. Studies on nondestructive testing (NDT) of wood based on electrical properties through dielectric spectroscopy (DS) are recently being developed, especially for standing tree evaluation. The study aimed to analyze the dielectric value of a fast-growing standing teak tree at frequency ranges 250 kHz – 60 MHz and to understand the relationships between physical and anatomical properties. Dielectric spectroscopy data were collected directly on the trees 4, 5, and 7 years old using a capacitance measurement system. Meanwhile, physical and anatomical samples were taken using a Ø 0.5 cm increment borer. The results showed that fiber length (FL), lumen diameter (LD), and fiber wall thickness (FWT) were significantly different at each tree age. This research found the optimal dielectric frequency to discriminate the wood properties in standing trees. There is a weak relationship (R= 0.2) in predicting the anatomical wood properties, while moderate to strong relationships (R= 0.4 to R= 0.8) are found in predicting wood density based on the selected frequency and moisture content variables. Further analyses and data processing can be improved by finding significant variables in the capacitance measurement system.

In Ethiopia, land degradation in the form of gully development and soil nutrient depletion is a very serious issue. The goal of this study is to determine how different types of land management practices and slope positions affect particular soil physico-chemical characteristics in the Agamssa watershed. Using systematic sampling techniques, soil samples were taken using a sampling quadrat (15 * 15 m) that was placed 50 m apart from one another. A total of 54 quadrats were planted at three slope positions: upper (>15%), middle (10–15%), and foot (3–10%) slope respectively. 18 composite soil samples were then. A two-way ANOVA was used to analyze the data, and the Least Significant Difference (LSD) test was used to separate the means at p ≤ 0.05. According to the study's findings, the value of most soil physical and chemical characteristics was higher in closed area than on open grazing land, as well as at foot slope position compared to middle and upper slope positions. The higher mean value (7.3 ppm) was recorded at the foot slope, while the lower mean value (4.9 ppm) was found at the upper slope position. The exchangeable cations such as Mg+2, K+, and Na+ were significantly (p≤ 0.01) affected by the main effect of land-use types. The higher mean values of Mg+2 (9.70 mq/100g), K+ (0.38 mq/100 g), and Na+ (0.035 mq/100 g) were found at area closure, whereas the lower mean values of Mg+2 (7.33 mq/100g), K+ (0.30 mq/100 g), and Na+ (0.027 mq/100g) were recorded at open grazing land. It was able to conclude this study that area closure enhances the physical and chemical qualities of soil and recovers woody plant species. Therefore, converting open grazing land into a closure area is advised.

The main motive of this study was to find an auxiliary application of the discarded agricultural remnants and poultry waste. Rice straw and chicken feathers are disposed off as landfills or incinerated causing pollution and environmental threats after their primary consumption. In this study epoxy composites were made using varying proportions of these raw and alkali treated materials. Flexural strength of the composites decreased till 35% fiber loading, followed by an increase. Chicken feather composites showed increased impact strength with fiber addition. Alkali treatment improved the mechanical properties of rice straw composites. Alkali treated chicken feather composites showed better impact strength but no significant change in flexural strength. Hybrid composites explicated enhanced properties both before and after alkali treatment corroborating noteworthy interfacial adhesion and synergistic effect of these fibers as ascertained from SEM images. The study evinced a better option for averting environmental problems by recycling these disposed materials.

Groundwater use for domestic and agricultural purposes is every day in rural communities. However, groundwater quality in those communities is still being determined due to the lack of water quality monitoring programs. The purpose of this study was to evaluate groundwater quality in rural communities using physiochemical parameters. Eight communities using communal boreholes were selected. Water samples were analysed for temperature, pH, electrical conductivity, total dissolved solids (TDS), ammonia, nitrate, and nitrite as Nitrogen. The pH means ranged from 6.6 to 8.1, whereas high TDS levels of 1390 mg/L and 1470 mg/L were observed in two boreholes. Three boreholes had higher electrical conductivity. Two boreholes had elevated nitrate levels of 15 and 21.5 mg/L. The high nitrate level correlates with the pH, EC, and TDS values. Our results suggest that high nitrate levels measured in communities’ boreholes pose ill health to the community, especially children, infants, and elders. Prenatal exposure to high nitrate has been found to have acute health effects in infants. Therefore, there is a need for further longitudinal studies on health risks among vulnerable groups in these communities.

Фундук является одним из самых ценных орехов в мире благодаря своим уникальным органолептическим свойствам и питательным характеристикам. Данная работа была направлена ​​на анализ некоторых физико-химических свойств различных сортов фундука, выращиваемых в Закаталы (Азербайджан), а именно Ата-баба, Эльбари, Топкара, Фирован, Насими, Галиб, Мирзебейли, Тала, Даш финтик, Барли, Азери и Сачагли. В целом результаты показали статистически значимые различия между изучаемыми сортами. Плотность ядер в зависимости от сортов фундука варьировала от 0,71 г/см ³ (азери) до 1,03 г/см ^{3 .}(Сачакли). Очищенные плоды Дашфиндыг в среднем были тяжелее (1,64±0,34 г), а очищенные плоды Насими, Калиб, Мирзебейли и Сачакли в среднем легче (0,8±0,23 г, 0,8±0,31 г, 0,8±0,20 г и 0,80 г). ±0,09 г соответственно.В неочищенном виде самыми тяжелыми были орехи Дашфиндык (3,70±0,34 г), а самыми легкими из всех сортов были орехи Насими и Калиб (2,0±0,48 г и 2,0±0,36 г соответственно). - орехи баба составляют 49 масс./ядро, %, у остальных изученных сортов - 33,3-45,3 мас.%. Орехи насими имеют округлую форму (в экваториальной зоне); талы, ата-баба, фирован и азери - округло-продолговатые; топкара , Барли и Даш финдык – продолговатые; Эльбари, Калиб, Мирзебейли и Сачакли – удлиненные. Фирован, Тала и Топкара имеют более толстую скорлупу. Ата-баба значительно опережает другие сорта по выходу ядер (490 кг/1 т орехов) , На втором месте по этому показателю находится Тала (453 кг/1 тонна орехов), на третьем – Топкара (433 кг/1 тонна орехов). По максимальной жирности выделены сорта Мирзебейли (77,00±2,20 г/100 г ядер) и Фирован (75,0±3,08 г/100 ядер), по белку - Сачакли (16,02±0,50 г/100 ядер) и Ата-баба ( выделено 15,92±0,48 г/100 г ядер). Результаты этого исследования помогают лучше понять различия между некоторыми сортами фундука, выращиваемого в Азербайджане, что дает важную информацию для всех участников этого сектора. 50 ед/100 ядер) и Ата-баба (15,92±0,48 г/100 г ядер). Результаты этого исследования помогают лучше понять различия между некоторыми сортами фундука, выращиваемого в Азербайджане, что дает важную информацию для всех участников этого сектора. 50 ед/100 ядер) и Ата-баба (15,92±0,48 г/100 г ядер). Результаты этого исследования помогают лучше понять различия между некоторыми сортами фундука, выращиваемого в Азербайджане, что дает важную информацию для всех участников этого сектора.

Formaldehyde, sulfuric acid and salicylic acid were combined to create 3,3’-methylenebis[2-hydroxybenzoic acid] (MHB) ligand, which was subsequently permitted to bind with zinc ions. The ligand and its zinc (II) complex (Zn-MHB) have been described by a combination of elemental analyses, spectral (UV-Vis, IR, MS, NMR), XRD, TEM as well as TGA measurement. The ligand has been suggested to coordinate to the zinc center in tetradentate manner forming binuclear tetrahedral complex. An X-ray analysis indicated a considerable difference between MHB (crystalline) and Zn-MHB (amorphous). UV-Vis spectra were used to determine the optical properties such as bandgap, refractive index, optical conductivity and penetration depth. Possibility of employing the samples for optoelectronic applications was indicated from the band gap values which underlie the range of semiconductors. TEM revealed spherical shapes and mutation of ligand particles into nano-scale by complexation. The antimicrobial potential of the MHB towards gram-positive and negative bacterial growths has been investigated. The results suggested that it would be possible to employ MHB to stop bacterial development, particularly salmonella typhimurium. Cytotoxicity of the MHB was assessed against two types of mammalian cells: VERO (the kidney of an African green monkey) and HFB4 (human skin melanocytes). Lower sensitivity was observed in VERO cells.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

Paper is a material whose mechanical properties are highly dependent on humidity and temperature. Which naturally also builds the relationship between the stiffness and strength of corrugated board and changing weather conditions. In this paper, attention is focused on the dependence of the physical properties of the cardboard on changes in humidity and temperature, which undergo dynamic fluctuations both during the production of corrugated board and during its storage. Two techniques were used to test this effect, namely numerical homogenization and global sensitivity analysis. Both methods were implemented to determine the theoretical relationships between the change in humidity and/or temperature in each layer of corrugated board and its global bending, compression and shear stiffness. The procedure was used to analyze different types of 5-ply and 3-ply cardboard. The obtained results allowed to build a complete map of the relationship between the change in humidity of selected layers and the strength characteristics of the full assembly.

Microbial communities play a key role in sustainable agriculture. However, we still need more in-formation, to understand the complex response of the microbial community to long-term organic farming, which aims to reduce synthetic fertilizer and pesticide use in order to produce sustainably and improve soil quality. We have assessed the long-term effect of two organic cropping systems and a conventional system on the microbial soil community structure using high-throughput se-quencing analysis. We analyzed the link between these communities and changes in soil properties and crop yield. Results showed that the crop yield was similar among the three cropping systems. Soil properties, such as total organic carbon, nitrogen, ammonium, magnesium and boron, influ-enced changes in the bacterial community structure. A linear discriminant analysis effect size (LEfSe) showed different bacteria and fungi as key microorganism of each of the three different cropping systems, in addition, our results reflected that fungal community were more sensitive than bacteria to cropping system. This research provides an insight about changes occurred in soils, especially in microbial communities considering the effect of that changes in crop yield which were remained stable among the different cropping systems.

Silicates are among the most abundant and important inorganic materials, not only in the Earth’s crust but also in the interstellar medium in the form of micro-/nano-particles or embedded in the matrices of comets, meteorites and other asteroidal bodies. Although the crystalline phases of silicates are indeed present in Nature, amorphous forms are also highly abundant. Here we report a theoretical investigation of the structural, dielectric and vibrational properties of the amorphous bulk for forsterite (Mg₂SiO₄) as a silicate test case by a combined approach of classical molecular dynamics (MD) simulations for structure evolution, and periodic quantum mechanical DFT calculations for electronic structure analysis. Using classical MD based on an empirical partial charge rigid ionic model within a melt-quenching scheme at different temperatures performed with the GULP 4.0 code amorphous bulk structures for Mg₂SiO₄ were generated using as initial guess the crystalline phase. This has been done for bulks with three different unit cell sizes adopting a super-cell approach; i.e., 1×1×2, 2×1×2 and 2×2×2. The radial distribution functions indicated a good degree of amorphisation of the structures. Periodic B3LYP-geometry optimizations performed with the CRYSTAL14 code on the generated amorphous systems were used to analyze their structure, to calculate their high frequency dielectric constants (ε_∞), and to simulate the IR, Raman and reflectance spectra, which were compared with the experimental and theoretical crystalline Mg₂SiO₄. The most significant changes of the physico-chemical properties of the amorphous systems compared to the crystalline ones are presented and discussed (e.g., larger deviations in the bond distances and angles, broadening of the IR bands, etc.), which are consistent with their disordered nature. It is also shown that by increasing the unit cell size the bulk structures present larger degree of amorphisation.

The lack of adequate knowledge of the culinary and sensory properties of most indigenous and wild foods hampers their promotion in human diets and the market. In the present study, 80 Burkinabe volunteers evaluated the sensory appeal and attributes of three selected Senegalia seed species (Zamnè, pseudoZamnè or Kumatiya, and S. erythrocalyx) and their food formulas (traditionally cooked, harvested as green and fresh legumes, and fermented as tempeh) using the 9-point hedonic scale and check-all-that-apply questionnaire. They found that the traditionally cooked Zamnè, pseudoZamnè or Kumatiya, and derived tempeh had good sensory appeal (scoring between 5-7) and subtle alkaline and nutty tastes, which will facilitate their blending in cuisines. Yet, an appreciable number (32%) of the participants, as unaccustomed to tempeh, scored all the tempeh products very low (2.5-3.4), suggesting food neophobia. In contrast, the traditionally cooked seeds of Senegalia erythrocalyx and the green and fresh Zamnè evoked bitter and sour off-tastes, respectively, and were not much appreciated (scoring 4). The present study provides unprecedented insight into consumers’ non-sensory perceptions and the culinary and sensory properties of Senegalia seed foods – which will be essential for their valorization, branding, and marketing.

High-performance poly(1,4-butylene terephthalate (PBT) nanocomposites have been developed via the consideration of phosphorus-containing agents and amino-carbon nanotube (A-CNT). One-pot functionalization method has been adopted to prepare functionalized CNTs via the reaction between A-CNT and different oxidation state phosphorus-containing agents, including chlorodiphenylphosphine (DPP-Cl), diphenylphosphinic chloride (DPP(O)-Cl), and diphenyl phosphoryl chloride (DPP(O3)-Cl). These functionalized CNTs, DPP(Ox)-A-CNTs (x = 0, 1, 3), were respectively mixed with PBT to obtain the CNTs-based polymer nanocomposites through a melt blending method. SEM observations demonstrated that DPP(Ox)-A-CNT nano-additives were homogeneously distributed within PBT matrix compared to A-CNT. The incorporation of DPP(Ox)-A-CNT improved the thermal stability of PBT. Moreover, PBT/DPP(O3)-A-CNT showed the highest crystallization temperature and tensile strength, due to the superior dispersion and interfacial interactions between DPP(O3)-A-CNT and PBT. PBT/DPP(O)-A-CNT exhibited the best flame retardancy resulting from the excellent carbonization effect. The radicals generated from decomposed polymer were effectively trapped by DPP(O)-A-CNT, leading to the reduction of heat release rate, smoke production rate, carbon dioxide and carbon monoxide release during cone calorimeter tests.

Synthetic materials such as Carbon, Kevlar, and Glass fibers are extensively utilized in various industries due to their superior characteristics including high stiffness, great strength, low den-sity, and high wear resistance, these advantages contributed to making them widespread in ap-plications like; aerospace, automobile, civil and electronics. This research is carried out to enhance the creep compliance of epoxy composite material by considering two types of fibers as reinforcement. A composite material is produced by combining two fibers, Kevlar fiber mixed with sika epoxy resin, along with Carbon fiber also mixed with sika epoxy resin using a Hand-Layup process. Experiments and numerical modeling are examined to offer a comprehensive understanding creep behavior of epoxy composite material in different weight ratios. Burger and Prony models are used to represent stress relaxation and creep strain of Visco-elastic material. According to the results, sika epoxy resin reinforced with Kevlar and Carbon fibers exhibits enhancement in the mechanical properties compared with pure epoxy. The use of Kev-lar/Sika epoxy composite results in higher creep compliance and modulus of elasticity compared with Carbon/Sika epoxy composite.

The review analyzes the studies published mainly in the last 10-15 years, on the synthesis, structure, and sensor properties of semiconductor nanocomposites. Particular attention is paid to the interaction between nanoparticles of the sensitive layer and its effect on the structure, sensitivity, and selectivity of semiconductor sensor systems. Various mechanisms are considered of interaction between nanoparticles in metal oxide composites including incorporation of metal ions of one component into the structure of another, heterocontacts between different nanoparticles, and core-shell systems, as well as their influence on the characteristics of gas sensors. The experimental data and studies on the modeling of charge distribution in semiconductor nanoparticles, which determine the conductivity and sensor effect in one- and two-component systems, are also discussed. It is shown that the model which considers the interactions of nanoparticles best describes the experimental results. Some mechanisms of detection selectivity are considered in the conclusion.

For thermoelectric materials study and development, it is very important to measure the electrical power and efficiency of a thermoelectric generator (TEG). In this study, thermoelectric properties such as electrical conductivity, Seebeck coefficient, and thermal conductivity of cement composites with graphene nanoplatelets and metallic oxides (Fe2O3, ZnO, MnO2) are measured and subsequently used to figure out the output electrical power and efficiency. A maximum of 1.5 W power per square meter for a temperature difference of about 50 °C can be estimated using GnP-ZnO added cement composites. This paper also talks about how to make a cement composite-based structural TEG module to enhance the total output voltage, power, and efficiency of the system.

The advent of graphene opens up the research into two-dimensional (2D) material, which is considered as a revolutionary material in the future. Due to its unique geometric structure, graphene exhibits a series of exotic physical and chemical properties. Besides, single-element-based 2D materials (Xenes) have garnered tremendous interest. At present, 16 kinds of Xenes (silicene, borophene, germanene, phosphorene, tellurene, etc.) have been explored, mainly distributed in the third, fourth, fifth and sixth main groups. The current methods to prepare monolayer or few-layer 2D materials include epitaxy growth, mechanical exfoliation, and liquid phase exfoliation. Although two Xenes (aluminene and indiene) have not been synthesized due to the limitations of synthetic methods or stability of Xenes, other Xenes have been successfully realized by elaborately artificial design and synthesis. Focusing on elemental 2D materials, this review mainly summarizes the recently reported work about tuning the electronic, optical, mechanical, or chemical properties of Xenes via surface modifications achieved by controllable approaches (doping, adsorption, strain, intercalation, phase transition, etc.) to broaden the applications in various fields, including spintronics, electronics, optoelectronics, superconducting, photovoltaics, sensors, catalysis, and biomedicines. These advances in surface modification of Xenes have laid a theoretical and experimental foundation for the development of 2D materials and their practical applications in diverse fields.

Suitable soil structure and nutrient security are important for plant growth and development, characteristics of soil fractal dimension and distribution of physical and chemical properties and their interactions play an important role in studying the stability of soil structure and water and fertilizer cycles. As a sustainable management model, intercropping has positive benefits for erosion control, spatial optimization of resources, as well as improving system productivity. The effects of four intercropping methods on soil fractal dimension and physicochemical properties were investigated by intercropping Salvia miltiorrhiza with forage and S. miltiorrhiza with forest under typical karst rock desertification habitats in Guizhou. The results showed that soil nutrient content of intercropping was significantly higher than that of monoculture, the organic carbon content of soil grown under forest is higher than other treatments, and there was a non-significant change in soil water content of intercropping compared with monoculture. The soil fine-grained matter of intercropping was significantly higher than that of monoculture, while the soil fractal dimension showed a tendency to become larger with the increase of fine-grained matter. The intercropping planting, due to its component types and spatial and temporal configurations, leads to differences in soil water and fertilizer interactions, which can be combined with other ecological restoration measures to optimize the composite model and jointly promote the restoration and development of ecologically fragile areas.

This paper examines the influence of the petrographic characteristics of sandstones from Klepa Nafpaktias (Greece) on their suitability in construction (concrete) and energy storage applications. For this scope, ten sandstones were collected in order to study their petrographic characteristics using petrographic microscope and a GIS software as well as their basic physical, mechanical and physicochemical properties. Concrete specimens (C25/30) were produced with constant volume proportions, workability, mixing and curing conditions using different sizes of each aggregate type. Aggregates were mixed both in dry and water saturated states in concrete. Three different types of sandstone aggregates were examined and classified in three district groups according to their physicomechanical properties, petrographic characteristics and surface texture. The classification in groups after the concrete compressive strength test (UCS) verified the initial classification in the same three groups relative to their grain size from coarse to fine grained. As the grain size decreases their physicomechanical and physicochemical properties are getting better resulting in higher concrete strength values (25 to 32 MPa). Furthermore, the proposed ratio C/A (crystals/ mm2) seems to influence the aggregate properties which constitute critical factors for the final concrete strength, presenting the more fine grained sandstones as the most suitable for concrete aggregates. Concerning the use of Klepa Nafpaktias sandstones as potential energy reservoirs, the studied sandstones have the appropriate physicochemical properties for the implementation of a financially feasible CO₂ capture and storage scenario.

Symmetrical and dissymmetrical bolaforms were prepared with good to high yields from unsaturated L-rhamnosides and phenolic esters (ferulic, phloretic, coumaric, sinapic and caffeic) using two eco-compatible synthetic strategies involving glycosylation, enzymatic synthesis and cross-metathesis under microwaves activation. Furthermore, some of these new compounds present good eliciting properties depending on the carbon chain length and on the nature of the hydrophilic head. Their respective antioxidant activities have been also evaluated as well as their cytotoxic properties on dermal cells for cosmetic uses.

: Greenhouse plants are usually grown in containers filled with growing media. Peat is the main component of the growing media used in greenhouses. However, peat substrate is made from peat from drained peatlands, which is a limited resource. Wood fiber can be an alternative to use as a growing media for controlled-climate crops. The chemical properties of the growing media interact and change continuously due to the small volume of the growing media, which is limited by the vegetative container. Therefore, this study aims to gain new knowledge on the impact of nutrient changes in the microbial degradation of carbon compounds in wood fiber and mixtures with peat substrate on the content and uptake of nutrients required by plants. Cucumbers (Cucumis sativus L.) were cultivated in growing media of peat substrate and wood fiber: (1) peat substrate (PS); (2) wood fiber (WF); (3) wood fiber and peat substrate 50/50 v/v (WF/PS 50/50); (4) wood fiber and peat substrate 25/75 v/v (WF/PS 25/75). The rates of fertilization were the following: (1) conventional fertilization (CF); (2) N13; (3) N23; (4) N30. Fertilization of cucumbers with different rates of nitrogen influenced the nutrient uptake. Plants grown in WF/PS 50/50 and WF/PS 25/75 growing media had the best Cu uptake when fertilized with N23. When the plants grown in the wood fiber media and the 50/50 media were fertilized with N13, N23, and N30, the Mn content in the growing media at the end of the growing season was significantly lower than the Mn content in the media with conventional fertilization. Thus, nitrogen improved the uptake of Mn by plants grown not only in the wood fiber but also in combinations with peat substrate. Growing plants in wood fiber and fertilizing them with N13 can result in optimum uptake of micronutrients. The number and mass of cucumber fruits per plant were influenced by the amount of wood fiber in the growing media and the application of nitrogen fertilizer. The highest number of fruits and mass of fruits per plant was obtained significantly higher when cucumbers were grown on WF/PS 50/50 growing media with additional N13 fertilization.

In this paper, a new method by combining cold drawing and martensitic transformation was proposed to produce ultrahigh-strength steel wire, and the effect of austenitizing heating rate on microstructure and mechanical properties was studied. Compared with Muffle furnace heating, salt bath heating has a much higher austenitizing heating rate, which is beneficial to obtain ultrafine-grained martensite for steel wire with a larger section. By salt bath hardening and low-temperature tempering, an ultrahigh strong (strength of 2.48 GPa) and tough (elongation of 6.0%) steel wire was produced. Moreover, to explore whether is it possible to replace long-time low-temperature tempering with short-time tempering at elevated temperatures to improve the tempering efficiency, the effect of tempering time on the evolution of microstructure and mechanical properties of the steel wires tempered at 350 °C was systematically studied. The results demonstrate that tempering at 350 °C for 30 s can endow the steel wire with comparable mechanical properties to that of the one tempered at 250 °C for 2 h. With tempering time prolonging, the strength decreases gradually with the precipitated phase transition from χ-Fe5C2 carbide into θ-Fe3C carbide and coarsening, which plays a major role in the strength decrease.

The consequences of climate change and anthropogenic stressors, such as habitat loss and overexploitation, are threatening the subsistence of species and communities across the planet. Therefore, it is crucial to analyze the impact of environmental perturbations on the diversity, structure and function of ecosystems. In this work, in silico simulations of biodiversity loss were carried out on the marine food web of Caleta Potter (25 de Mayo Island, Antarctica) where global warming has caused critical changes in the abundance and distribution of benthic and pelagic communities during the last 30 years. We performed species removal considering their degree and trophic level and including four different thresholds on the occurrence of secondary extinctions. We examined the impact of extinctions on connectance, modularity and stability of the food web. We found different responses of these properties depending on the extinction criteria used, e.g., large increase in modularity and rapid decrease in stability when most-connected and relatively high-trophic level species were removed. Additionally, we studied the complexity-stability relationship of the food web founding two regimes: 1) high sensitivity to small perturbations suggesting that Potter Cove would be locally unstable, and 2) high persistence to long-range perturbations suggesting global stability of this ecosystem.

The successive steps of the oxidation mechanism of crocin, major compound of saffron, by the free OH• radical are investigated by the pulse radiolysis, steady-state (gamma) radiolysis methods and molecular simulations. The optical absorption properties of the transient species and their reaction rate constants are determined. The absorption spectrum of the oxidized radical of crocin resulting from the H-abstraction presents a maximum at 678 nm and a band at 441 nm, almost as intense as that of crocin. The spectrum of the covalent dimer of this radical contains an intense band at 441 nm and a weaker one at 330 nm. The final oxidized crocin, issued from radical disproportionation, absorbs weaker with a maximum at 330 nm. The molecular simulation results suggest that the OH• radical is electrostatically attracted by the terminal sugar and is scavenged predominantly by the neighbor methyl site of the polyene chain as in a sugar-driven mechanism. Based on detailed experimental and theoretical investigations, the antioxidant properties of crocin are highlighted.

The aim of the study was to verify whether a 20 and 40% reduction of nitrogen (N) fertilization rate will be sufficient to maintain soil basic chemical features, fertility, and yielding in monoculture maize cultivation in the no-tillage (NT) system versus the traditional plowing (PL) system. In addition, it was examined which tillage system (PL, NT) allows reduction of fertilization while maintaining good yields of the tested soils. Two fields (10 ha each) were established for PL and NT maize cultivation and soils (0-20 cm) were sampled two times per year - in spring (before maize sowing) and in autumn (after maize harvesting). A broad range of chemical and biological parameters (i.e. pH, forms of nitrogen, phosphorus and carbon, content of selected macronutrients and humic substances, respiration activity) were monitored during the experiment. It was evidenced that the 20% reduction in N fertilization does not have an adverse effect on the chemical and biological characteristics of soils. In turn, the maize yield was mainly the result of both the tillage system and the N rate, i.e. it was significantly higher in the PL system.

In this paper we present magnetoelectric properties of metal/metal-oxide/metal junctions. We use Ti and Fe as metallic layers separated by the porous metal-oxides of iron or titanium formed with the anodization method. This allowed to prepare double junctions with at least one ferromagnetic layer. Here we show magnetoresistance and current-voltage characteristics of the junctions together with their magnetic characteristics. We found positive or negative magnetoresistance depending on junction composition. We discuss also the nature of differential resistance calculated from I-V characteristics. Our findings show that the strongest influence on observed behaviour has a top metallic layer and the interface between this layer and anodized oxide where strong interatomic diffusion is expected.

This study aimed to characterize the antioxidant, mechanical and physical properties of chicken skin gelatin/CMC/Centella asiatica blended film. The influence of Centella asiatica at 0.3% and 0.7% on antioxidant activities; mechanical properties and physical properties of chicken skin gelatin/CMC/Centella asiatica film were investigated. Characterization of the blended films with 0.7% Centella asiatica extract shows higher antioxidant activities with a total phenolic content of 0.36 mg/g of GAE, DPPH of 89.26%, and reducing power of 0.80 nm compared to 0.3% Centella asiatica extract. The addition of 0.3% of Centella extract provide higher value in tensile strength (5.0 × 10⁻² MPa), elongation at break (281%), melting point (131.31 °C), transparency (0.86) but lower UV-light penetration. While the addition of 0.7% Centella extract contribute to higher value in WVP (1.13 × 10⁻⁴ g m⁻¹s⁻¹Pa⁻¹) and puncture test (0.06 N). There are no significant differences between functional groups obtained from this blended film as evaluated by FTIR analysis (p > 0.05). Furthermore, XRD analysis showed the addition of extract decrease the crystallinity of film. In conclusion, the incorporation of Centella asiatica extracts on film greatly increased antioxidant levels and improved some of the mechanical and physical properties of the film blends.

Butanol extracts from leaves, twigs and fruits of Elaeagnus rhamnoides (L.) A. Nelson (sea buckthorn, SBT) were fractionated into phenolic and non-polar lipid components. Their chemical composition was analyzed using the Thermo Ultimate 3000RS chromatographic system, equipped with a diode array detector, a corona-charged aerosol detector, and coupled with a (Q-TOF) mass spectrometer. Assuming that an effect on natural microbiotaand host epithelial cells needs to be assessed, regardless of the purpose of using SBT formulations in vivo, the MIC/MBC/MFC of the fractions and reference phytocompounds were screened involving 17 species of Gram-positive and Gram-negative bacteria and Candida species. The impact of the fractions (subMIC) on the important in vivo persistence properties of S. aureus and C. albicans strains was evaluated. Tests for adhesion and biofilm formation on an abiotic surface and the surfaces conditioned with fibrinogen, collagen, plasma or artificial saliva showed the inhibitory activity of the fractions. The effects on FITC-labeled staphylococci adhesion to fibroblasts (HFF-1) and epithelial cells (Caco-2), and on fungal morphogenesis, indicated that SBT extracts have high anti-virulence potential. Cytotoxicity tests (MTT-reduction) on the standard fibroblast cell line showed variable biological safety of the fractions depending on their composition and concentration.

Conventional pervious pavement materials (PPM) consist of cement and aggregate materials and are known for poor durability due to their brittle behavior. Herein, we fabricated polymeric PPMs from durable and abundant polyurethane (PU) to enhance the durability of the material and undertook mechanical and microscopic characterizations. PU-based PPM samples with varying aggregate sizes were produced and the compressive strength and water permeability of each were examined. The pore and tortuosity characteristics of the specimens were analyzed using X-ray micro-computed tomography (micro-CT). Through the micro-CT analysis, the morphological characteristics of the internal structures of PPM were identified and the correlations between the pore size distribution, connectivity, and tortuosity within the specimen were quantitatively analyzed. The microstructures derived from micro-CT were generated as a finite element model and the stress distribution generated inside was numerically determined.

Star copolymer films were studied for confirming the role of film morphology in antimicrobial activity previously reported. With this scope, films of a two-branches copolymer, namely m-PEG-(MMA-ran-DMAEMA)2, containing ≈ 40 % in mol of non-quaternized 2-(dimethylamino)ethyl methacrylate, were produced by using spin-coating, drop-casting and casting deposition techniques, thus obtaining ultra-thin, thin and thick films, respectively. The morphology is generally flat for thin and thick films, but it becomes substrate dependent for ultra-thin films where the film planarization effect is not efficient. Mechanical properties of such films were investigated by Force Volume Maps in both air and liquid. In air, ultra-thin films are in the substrate-dominated zone and thus the elastic modulus E is overestimated, while E reaches its bulk value for thin and thick films. In liquid (water), E follows an exponential decay for all films with a minimum soaked time t0 of 0.37 and 2.65 h for ultra-thin and thin and thick films, respectively. After this time, E saturates to a value in average 92 % smaller than that measured in air due to films swelling. Such results confirm the role of morphology envisaged in literature, suggesting also an additional role of mechanical properties in the antimicrobial activity.

The research field of two dimensional (2D) materials strongly relies on optical microscopy characterization tools to identify atomically thin materials and to determine their number of layers. Moreover, optical microscopy-based techniques also opened the door to study the optical properties of these nanomaterials. We present a comprehensive study of the differential reflectance spectra of 2D semiconducting transition metal dichalcogenides (TMDCs), MoS₂, MoSe₂, WS₂ and WSe₂, with thickness ranging from one layer up to six layers. We analyze the thickness-dependent energy of the different excitonic features, indicating the change in the band structure of the different TMDC materials with the number of layers. Our work provides a route to employ differential reflectance spectroscopy for determining the number of layers of MoS₂, MoSe₂, WS₂ and WSe₂.

No-till and cereal-legume intercropping have been recognized as favorable cropping practices to increase crop yields while maintaining soil quality in arid and semiarid environment, but the bio-logical mechanisms are poorly understood. The present study was to determine the response of soil properties, enzyme activities, and microbial community diversity and composition in mono- and inter-cropping under conventional and no-tillage conditions. We initiated a field experiment in Wuwei, a typical arid area of China, in 2014. Soil was sampled in August 2022 and, yields, soil properties, enzyme activities, and the microbial community diversity and composition were de-termined in the maize and pea strips in inter- and mono-cropping systems. Results revealed that the maize and pea strips in the no-till intercropping significantly increased yields, total and or-ganic carbon stocks, decreased NO3--N, and obtained the highest total and organic P in the soil. The α- and β-diversity of archaea and eukaryotes were significantly affected by planting patterns, while α- and β-diversity of the bacterial community were significantly affected by tillage practices. Both no-tillage and intercropped maize significantly increased the abundance of archaea phylum Thaumarchaeota and bacterial phylum Nitrospirae, benefiting nitrogen fixation of intercropped pea from the atmosphere under the no-tillage cereal/legume intercropping. No-till intercropping was conducive to the accumulation of organic carbon, while decreasing the abundance of Prote-obacteria, Acidobacteria, and Verrucomicrobia. Limited soil enzyme activities (ACP, ALP, DP, NAG, BG, AG, CB) led to decreases in organic carbon turnover and utilization. Intercropping al-tered soil microbial community diversity and composition due to changes in soil properties and enzyme activities. These findings suggest that no-tilled cereal-legume intercropping is a sustaina-ble cropping practice for improving soil properties and enhancing microbial (archaea, bacterial, Eukaryota) diversity, but the long-term persistence is not conducive to rapid turnover of soil nu-trients due to limited enzyme activities.

Copper-nitride (Cu3N) material is attracting much attention as a potential next-generation thin-film solar-light absorber. In this work, polycrystalline Cu3N thin films were prepared using reactive-RF-magnetron sputtering, at room temperature,onto glass and silicon substrates. The optical properties of the Cu3N thin layers were studied by spectroscopic ellipsometry and transmission, to achieve a low-cost absorber material to replace conventional silicon. The reactive-RF-sputtered Cu3N films were also investigated by FIB-SEM microscopy and FTIR spectroscopy.

Biowaste generated in the process of Oxytree cultivation and logging represents a potential source of energy. Torrefaction (a.k.a. low-temperature pyrolysis) is one of the methods proposed for the valorization of woody biomass. Still, energy is required for the torrefaction process during which the raw biomass becomes biochar with fuel properties similar to lignite coal. In this work, models describing the influence of torrefaction temperature and residence time on the resulting fuel properties (mass and energy yields, energy densification ratio, organic matter and ash content, combustible parts, lower and higher heating values, CHONS content, H:C and O:C ratios) were proposed according to the Akaike criterion. The degree of the models’ parameters matching the raw data expressed as the determination coefficient (R²) ranged from 0.52 to 0.92. Each model parameter was statistically significant (p<0.05). Estimations of the value and quantity of the produced biochar from 1 Mg of biomass residues were made based on two models and a set of simple assumptions. The value of torrefied biochar (€123.4·Mg^-1) was estimated based on the price of commercially available coal fuel and its lower heating value (LHV) for biomass moisture content of 50%, torrefaction for 20 min at 200 °C. This research could be useful to inform techno-economic analyses and decision-making process pertaining to the valorization of pruned biomass residues.

The improvement of mechanical properties of cantala fiber and its composites. Treatments including alkali, silane, and the combination of both were carried out to modify the fiber surface. The influence of chemical treatments on fiber properties such as the degree of crystallinity and tensile strength was investigated. A variety of short cantala fiber reinforced rHDPE composites were produced by hot press, and the effect of fiber treatment on the flexural strength of composites was observed. SEM observations also carried out to highlight these changes. The result shows that alkali treatment improves tensile strength and tensile modulus of alkali treated fiber (NF12) which was predicted as a result of the enhancement of the cellulose crystallinity. In contrast, the tensile strength and tensile modulus of silane (SF05) and alkali-silane treated fiber (NSF05) decreased compared to untreated fiber (UF) which is caused by the addition of amorphous material. The tensile strength of alkali-silane treated fiber (NSF05) was lower than alkali treated fiber (NF12), but the composites prepared with NSF05 showed the highest increment of flexural strength of 25.9%. This may be due the combination of alkali and silane treatment helped in the better formation of fiber-matrix interface adhesion.

Technical components should be produced sustainably and are subject to growing demands in terms of durability and reliability. To meet these expectations, the development of thermochemical processes is auspicious. Titanium alloys, which have a comparatively high gas solubility, allow temporary hydrogen (H) loading, often called thermo hydrogen treatment (THT). THT causes lattice deformation and reduces the β transformation temperature. These effects enable an adjustment of the microstructure, which improves the mechanical properties as compared to those produced conventionally. Furthermore, the process is applicable to complex geometries that cannot be surface hardened by mechanical surface treatment techniques. The investigation presented intends to realize a local microstructure gradient in additively via laser-powder bed fusion (L-PBF) manufactured cylindrical Ti–6Al–4V specimens by changing the distribution and morphology of strengthening precipitates as well as the β grain size depending on the distance to the surface, which should improve the material fatigue properties. To evaluate the mechanical properties of such THT-induced microstructure gradients, the resulting change in fatigue life in the LCF and HCF range was determined by stress-controlled cyclic deformation tests. Besides, the resulting microstructure was characterized by means of XRD and TEM. In addition to the additively manufactured and thermo hydrogen treated cylindrical specimens, conventionally produced tube-like specimens were thermo hydrogen treated and examined. For the THT-induced microstructure gradients, numerically simulated H concentration profiles as well as experimentally determined hardness profiles were used for the evaluation of the THT process. The study shows that H-loading at 500°C and H-degassing at 750°C, followed by aging at 550°C, allows the establishment of a microstructure gradient that shows an 8% improvement in fatigue properties compared to a reference condition without THT. The reason for this improvement is an increased volume fraction secondary alpha phase in the near-surface area of the specimens. Moreover, the results show that the process is applicable a tube-like specimen with varying wall thicknesses.

The article describes the use of microwave irradiation in the synthesis of bis(cyclo carbonate) compounds (BCC) in bulk (without solvent) from carbon dioxide capture using an epoxidized compound - a commercial epoxy resin, and compares this process to the conventional method. CO2 cycloaddition to epoxides is an ecological and efficient method for the formation of bis(cyclic carbonates). Moreover, the introduction of gas into the reaction mixture was carried out at atmospheric pressure with a controlled flow rate, which is advantageous from an economic point of view. Progressive structural changes and the presence of characteristic chemical groups were monitored using attenuated total reflectance infrared spectroscopy with Fourier transform. The obtained crude products were purified to obtain three fractions, which were subjected to detailed structural analysis using FT-IR and 13CNMR. The formation of the main product with two cyclic carbonates was confirmed. The presence of monomers, dimers and trimers in individual fractions as well as their thermal stability were determined, and the molecular masses in individual fractions were determined using gel permeation chromatography (GPC).

This study assessed the impact of mineral fertilization on tuber yield and food quality of yam genotypes, specifically Dioscorea alata and Dioscorea rotundata. Four genotypes, each from D. alata and D. rotundata, were used in field experiments conducted in Ibadan, Nigeria, in the 2017 and 2018 cropping seasons. Experiments were conducted under low soil NPK fertility conditions with and without fertiliser treatments. A recommended NPK rate for the area (90, 50, and 75 Kg N, P, K ha-1) was applied to plots with fertiliser treatment. Tuber yield, functional and pasting properties of yam flour, and sensory attributes of pounded yams were collected. The results showed differential responses of the genotypes to tuber yield and food quality with fertiliser application. Fertiliser application has generally increased fresh tuber yield, but it has affected some genotypes' flour quality and textural attributes of the pounded yams. As regards genotypes Danacha and TDa0200012, fertiliser application has increased tuber yield without causing a decrease in tuber quality hence, suggesting Danacha and TDa0200012 as suitable genotypes for maximizing fertiliser productivity. However, in another genotype Ojuiyawo, fertiliser application effectively increased tuber yield but deteriorated tuber quality. Our results suggested that it is crucial to determine the impact of fertilisation on tuber yield and quality for each genotype and select the appropriate genotype to improve productivity through mineral fertilisation. The results of this study can be widely applied to enhance yam productivity in sub-Saharan Africa and useful for sustainable agriculture in yam-growing areas.

The main objective of this work is to study the effects of carbon nanotubes (CNT) on the strength and electrical properties of cement mortar. Molecular dynamic simulations (MDS) were carried out for the mechanical and electrical properties of the cementitious composite and the associated mechanisms. To model the atomic structure of the Calcium-Silicate-Hydrates (C-S-H) gel, tobermorite 11Å was chosen. Single-walled carbon nanotubes (SWCNTs) embedded in tobermorite structure were tested numerically. In particular, the effect of the concentration of CNT in cement paste was studied. An innovative experiment of electrical characterization of a cementitious composite of carbon nanotubes has been developed.

Copper-nitride (Cu3N) semiconductor material is attracting much attention as a potential, next-generation thin-film solar-light absorber in solar cells. In this communication, polycrystalline Cu3N thin films were prepared using reactive-RF-magnetron-sputtering deposition, at room temperature, onto glass and silicon substrates. The very-broadband optical properties of the Cu3N thin film layers were studied by UV-MIR (0.2-40 μm) ellipsometry and optical transmission, to be able to achieve the goal of a low-cost absorber material to replace the conventional silicon. The reactive-RF-sputtered Cu3N films were also investigated by focused ion beam scanning electron microscopy, and both FTIR and Raman spectroscopies.