To solve the problem of complex sensor installation and easy damage in contact displacement measurement, a non-contact measurement method of brace displacement in bridge swivel construction based on binocular vision is proposed in this study. Combined with monitoring data in a swivel construction interchange project, binocular vision system was compared and analyzed with the traditional displacement meter and total station. Results showed that force versus displacement variation plots were obtained by binocular visual measurement in the weighing test, the inflection point can be clearly distinguished, and the position of the inflection point was the same as that of the displacement meter; monitoring data of binocular vision measurement and total station were compared and analyzed in the bridge swivel process, the average error was no more than 0.18 mm, the maximum error was no more than 0.42 mm, and the standard deviation was no more than 0.12. The method proposed in this study can be used as an alternative to displacement meter and total station measurement methods in bridge swivel construction, the problem of complex sensor installation and easy damage is solved in brace displacement measurement, equipment and labor costs can be effectively saved.

Background Ultrasonographic measurement of the optic nerve sheath diameter (ONSD) is helpful in the assessment of intracranial pressure. The aim of this study was to determine whether the Trendelenburg position during laparoscopic urological surgery changed the ONSD and whether changes correlated with postoperative complications. Methods In this prospective study, we measured ONSD before patients were placed in the Trendelenburg position. Then the Trendelenburg position was established by tilting the operating table to 20-25 degrees. After surgery, the patients were placed in a horizontal position, and the second measurement of ONSD was obtained. Results The study included 69 patients. The average preoperative ONSD in the right eye was 5.8 ± 0.7 mm and 5.8 ± 0.8 mm in the left eye. The average postoperative ONSD in the right eye was 6.6 ± 0.8 mm and 6.6 ± 0.7 mm in the left eye. The differences between postoperative and preoperative values in the right and left eyes were statistically significant (p <0.000001). ONSD increases above the norm did not correlate with the incidence of postoperative nausea (p = 0.94), delirium (p = 0.81), or the time to patient awakening (p = 0.29). Conclusion ONSD increased in patients who underwent surgical procedures performed in the Trendelenburg position, but the increase did not correlate with postoperative complications.

With the rise of the Internet of Things (IOT), mobile devices and Location-Based Social Network (LBSN), an abundant amount of trajectory data has made research on location prediction more popular. The check-in data shared through LBSN hides information related to life patterns, obtaining this information is helpful for location prediction. However, the trajectory data recorded by mobile devices is different from check-in data that has semantic information. In order to obtain the user’s semantic, relevant studies match the stay point to the nearest Point of Interest (POI), but location error may lead to wrong semantic matching. Therefore, we propose A Self-Attention for Next Location Prediction based on Semantic Mining to predict the next location. When calculating the semantic feature of a stay point, the first step is to search for the k nearest POI, then use the reciprocal of the distance from the stay point to the k nearest POI and the number of categories as weights. Finally, we use the probability to express semantic without losing other important semantic information. Furthermore, this research combined with sequential pattern mining can bring richer semantic features. In order to better perceive the trajectory, temporal features learn periodicity of time series by sine function. In terms of location features, we build a directed weighted graph and regard the frequency of users visiting locations as the weight, so the location features are rich in contextual information. We then adopt the Self-Attention model to capture long-term dependencies in long trajectory sequences. Experiments in Geolife show that the semantic matching of this study improved by 45.78% in TOP@1 compared with the closest distance search for POI. Compared with the baseline, the model proposed in this study improved by 2.5% in TOP@1.

We develop a quantitative microscopic theory of decaying Turbulence by studying the dimensional reduction of the Navier-Stokes loop equation for the velocity circulation. We have found an infinite dimensional manifold of solutions of the Navier-Stokes loop equation\cite{M93, M23PR} for the Wilson loop in decaying Turbulence in arbitrary dimension $d >2$. This family of solutions corresponds to a fractal curve in complex space $\mathbb C^d$, described by an algebraic equation between consecutive positions plus a nonlinear periodicity condition. We derive the constrained SDE for the evolution of the fractal curve at a fixed moment of physical time as a function of an auxiliary stochastic time. We expect this stochastic process to cover our fixed manifold of the solutions of the decaying Turbulence. The energy density of the fluid decays as $\mathcal E_0/t$, where $\mathcal E_0$ is an initial dissipation rate. Presumably, we have found a new phase of extreme Turbulence yet to be observed in real or numerical experiments.

Inflammatory bowel disease (IBD), comprising Crohn's disease (CD) and ulcerative colitis (UC), defines as an idiopathic, chronic, relapsing, inflammatory disease affecting the gastrointestinal tract and leading to chronic damage. Endoscopy with biopsies is considered the gold standard for IBD diagnosis, whereas magnetic resonance (MRI) for CD extension and complication assess-ment. However, the latter are invasive procedures; thus, the need for a reliable, accessible and noninvasive way to perform IBD diagnosis and monitoring in the tight control era, like intestinal ultrasound (IUS) is. Compared to endoscopy and MRI, IUS has shown reliable diagnostic accuracy in assessing CD and UC severity and extension. Performing IUS in a point-of-care setting (POCIUS) can guide the clinician in driving the diagnostic and therapeutic pathway, thus accel-erating clinical decisions. POCIUS performed with pocket devices can represent the future of physical examination in outpatient or inpatient examination. Accordingly, we performed a liter-ature review about the application of IUS in CD and UC diagnosis. Furthermore, we explored the technical aspects of this imaging technique and its application in a point-of-care setting.

In this paper, we prove some common fi xed point theorems on complex partial metric space. The presented results gener- alize and expand some of the literature well-known results. We also explore some of the application of our key results.

This article has two objectives. Firstly, we will use the vector variational-like inequalities problems to achieve local approximate (weakly) efficient solutions of Vector Optimization Problem within the novel field of the Hadamard manifolds. Previously, we will introduce the concepts of generalized approximate geodesic convex functions and illustrate them with examples. We will see the minimum requirements under which critical points, solutions of Stampacchia and Minty weak variational-like inequalities and local approximate weakly efficient solutions can be identified, extending previous results from the literature for linear Euclidean spaces. Secondly, we will show an economical application, using again solutions of the variational problems to identify with Stackelberg equilibrium points on Hadamard manifolds and under geodesic convexity assumptions.

A run-of-the-mill remote sensor arrange comprises numerous vitality compelled sensor hubs that are arbitrarily sent is the sensor field. Vitality is one of the most significant parts of planning an information dispersal convention for applications, for example, war zone checking, living space observing, and so on. We present EGDD, an Energy-effective Grid-based Data Dissemination plot for arbitrarily conveyed remote sensor systems. The proposed conspire is vitality effective for dealing with both sink and source portability. EGDD depends on a virtual framework-based foundation for information scattering from various versatile sources to different portable sinks. The virtual lattice of square size is built by the main source showing up in the sensor field dependent on the remaining vitality of the sensor hubs. Moreover, we proposed an askew sending calculation for inquiry and information sending which guarantees that just a single spread hub advances the question and information at once. In EGDD, substitute scattering hubs are chosen ahead of time during the lattice development procedure and the least limit vitality level is characterized for spread hubs. When the vitality of a dispersal hub arrives at the base edge esteem, it is supplanted by another spread hub. The reenactment results show that the proposed EGDD conspire is more vitality proficient when contrasted with other information scattering conventions.

In this study, we investigate the form of solutions, stability character and asymptotic behavior of the following four rational difference equations x_{n+1} = (1/(x_{n}(x_{n-1}±1)±1)), x_{n+1} = ((-1)/(x_{n}(x_{n-1}±1)∓1)), such that their solutions are associated with Tribonacci numbers.

In the framework of a multiplicative metric space. We have discuss some Properties of convex structures in pseudo multiplicative metric space and have applied these properties toiobtain alfixed point results in complete pseudo. It would be interesting to prove some further results in such metric spaces with completeness property.

A wealth of Full Waveform (FW) LiDAR data are available to the public from different sources, which is poised to boost the extensive application of FW LiDAR data. However, we lack a handy and open source tool that can be used by potential users for processing and analyzing FW LiDAR data. To this end, we introduce waveformlidar, an R package dedicated to FW LiDAR processing, analysis and visualization as a solution to the constraint. Specifically, this package provides several commonly used waveform processing methods such as Gaussian, adaptive Gaussian and Weibull decompositions, and deconvolution approaches (Gold and Richard-Lucy (RL)) with users’ customized settings. In addition, we also developed functions to derive commonly used waveform metrics for characterizing vegetation structure. Moreover, a new way to directly visualize FW LiDAR data is developed through converting waveforms into points to form the Hyper Point cloud (HPC), which can be easily adopted and subsequently analyzed with existing discrete-return LiDAR processing tools such as LAStools and FUSION. Basic explorations of the HPC such as 3D voxelization of the HPC and conversion from original waveforms to composite waveforms are also available in this package. All of these functions are developed based on small-footprint FW LiDAR data, but they can be easily transplanted to the large footprint FW LiDAR data such as Geoscience Laser Altimeter System (GLAS) and Global Ecosystem Dynamics Investigation (GEDI) data analysis. It is anticipated that these functions will facilitate the widespread use of FW LiDAR and be beneficial for better estimating biomass and characterizing vegetation structure at various scales. The package and code examples can be found at https://github.com/tankwin08/waveformlidar.

To improve the effect of multi-point stretch forming of sheet metal, it is proposed in this paper to replace fixed ball head with swinging ball head. According to the multi-point dies with different arrangements, this research establishes the finite element models of the following stretch forming, i.e. fixed ball heads with conventional arrangement, swinging ball heads with conventional arrangement, swinging ball heads with declining staggered arrangement, and swinging ball heads with parallel staggered arrangement and then numerical simulation is performed. The simulation results show that by replacing fixed ball head with swinging ball head, the surface indentation of the formed part was effectively suppressed, the stress and tension strain distribution of the formed part was improved and the forming quality was improved; that the thickness of the elastic pad was reduced, the springback was reduced and the forming accuracy was improved; and that when the ball head was applied to multi-point die with staggered arrangement, better forming result was achieved, where the best forming result was achieved in combining the swinging ball heads with the multi-point die with parallel staggered arrangement. The forming experiments were carried out, and the experimental results were consistent with the trend of numerical simulation results, which verified the correctness of the numerical simulation.

Model-based design has received considerable attention in biological and chemical industries over the last two decades. However, the parameter uncertainties of first-principle models are critical in model-based design and have led to the development of robustification concepts. Various strategies were introduced to solve the robust optimization problem. Most approaches suffer from either unreasonable computational expense or low approximation accuracy. Moreover, they are not rigorous and do not consider robust optimization problems where parameter correlation and equality constraints exist. In this work, we propose a highly efficient framework for solving robust optimization problems with the so-called point estimation method (PEM). The PEM has a fair trade-off between computation expense and approximation accuracy and can be easily extended to problems of parameter correlations. From a statistical point of view, moment-based methods are used to approximate robust inequality and equality constraints. We also suggest employing the information from global sensitivity analysis to further simplify robust optimization problems with a large number of uncertain parameters. We demonstrate the performance of the proposed framework with two case studies where one is to design a heating/cooling profile for the essential part of a continuous production process and the other is to optimize the feeding profile for a fed-batch reactor of the penicillin fermentation process. The results reveal that the proposed approach can be used successfully for complex (bio)chemical problems in model-based design.

Since the systematic evolution of ligands by exponential enrichment (SELEX) method was developed, aptamers have made significant contributions as bio-recognition sensors. Microdevice systems allow for low reagent consumption, high-throughput of samples, and disposability. Due to these advantages, there has been an increasing demand to develop microfluidic-based aptasensors for analytical technique applications. This review introduces the principal concepts of aptasensors and then presents some advanced applications of microdevice-based aptasensors on several platforms. Highly sensitive detection techniques such as electrochemical and optical detection have been integrated into lab-on-a-chip devices and researchers have moved towards the goal of establishing point-of-care diagnoses for target analyses.

In our previous works we have proposed design equations that can predict with reasonable accuracy the transition point from homogeneous to heterogeneous regime as well as the gas holdup and the mean Sauter diameter at the homogeneous regime. The validity of the proposed correlations was checked with data obtained using different geometrical configurations and several Newtonian and non-Newtonian liquids as well as the addition of surfactants. However, in all the experiments the gas phase was atmospheric air. This work investigates the effect of gas phase properties by conducting experiments employing various gases (i.e., air, CO₂, He) that cover a wide range of physical property values. Experiments revealed that only the use of low-density gas (He) has a measurable effect on bubble column performance. More precisely, when the low-density gas (He) is employed, the transition point shifts to higher gas flow rates and the gas holdup decreases, a fact attributed to the lower momentum force exerted by the gas. In view of the new data, the proposed correlations have been slightly modified to include the effect of gas phase properties and it is found that they can predict the aforementioned quantities with an accuracy of ±15%. It has been also proved that CFD simulations are an accurate means for assessing the flow characteristics inside a bubble column.

Code summarization plays a vital role in aiding developers with program comprehension by generating corresponding textual descriptions for code snippets. While recent approaches have concentrated on encoding the textual and structural characteristics of source code, they often neglect the global hierarchical features causing limited code representation. Addressing this gap, our paper introduces the Statement-grained Hierarchy enhanced Transformer model (SHT), a novel framework that integrates global hierarchy, syntax, and token sequences to automatically generate summaries for code snippets. SHT is distinctively designed with two encoders to learn both hierarchical and sequential features of code. One relational attention encoder processes the statement-grained hierarchical graph, producing hierarchical embeddings. Subsequently, another sequence encoder integrates these hierarchical structures with token sequences. The resulting enriched representation is then fed into a vanilla Transformer decoder, which effectively generates concise and informative summarizations. Our extensive experiments demonstrate that SHT significantly outperforms state-of-the-art approaches on two widely used Java benchmarks. This underscores the effectiveness of incorporating global hierarchical information in enhancing the quality of code summarizations.

Digital music is one of the most important things in market due to the music royalties’ distribution in Korea. As the music market is transformed to the digital music market such as download the music and streaming, the distribution of music royalties starting from online service provider (OSP) has come to be a highly important part for music rights holders. One of the most important issues in current music royalties’ distribution in Korea is the unfair way of music royalties due to indiscriminative repeat streaming of digital music. To prevent this, music log usage data from several OSPs was collected in day-based system, however, there was a limit to identify detailed information on the use of music in current state. This paper analyzed the structural problems and limitations of settlement of music royalties, and provides a structure in which there can be transparent settlement and distribution between users and rights holders as one of the institutional measures. We’ll also propose various AI-based applications using music log usage data. The proposed system will hopefully be used for public purposes.

Single photon ionization (SPI) based on vacuum ultraviolet (VUV) lamps has been extensively investigated and applied due to its clean mass spectra as a soft ionization method. However, the photon energy of 10.6 eV and photons flux of 106 photons/s of commercial VUV lamp limits its range of ionizable analytes as well as sensitivity. This work designs a chemical ionization focusing integrated (CIFI) ionization source time-of-flight mass spectrometry (TOFMS) based on VUV lamp for the detection of volatile organic compounds (VOCs) and oxygenated volatile organic compounds (OVOCs). The photoelectrons obtained from the VUV lamp through the photoelectric effect ionized the oxygen in the air to obtain the reagent ions O2+, and segmented quadrupole constituted the ion-molecule-reaction region (IMR) and radially focused the ions using a radio-frequency electric field, which improved the yield and transport efficiency of the sample ions and the sensitivity of mass spectrometry, resulting in 44-fold and 1154-fold increase in signal response to benzene and pentanal, respectively. To verify the reliability of the ionization source, the linear correspondence and repeatability of benzene and pentanal were investigated. Satisfactory dynamic linearity was obtained in the concentration range of 5-50 ppbv, and daytime RSD reached 3.91% and 6.26%, respectively. Finally, the CIFI ionization source TOFMS was applied to the determination of OVOCs, and the LOD of 12 types of OVOCs can reach the pptv level, indicating that the ionization source has the potential for accurate and sensitive online monitoring of atmospheric OVOCs.

Pore fluid pressure is very important to the generation, migration and accumulation of petroleum. The previous studies indicate that the Chezhen sag region is typically characterized by pore fluid overpressure (the difference between pore fluid pressure and hydrostatic pressure). To date, the formation mechanism of pore overpressure and the accumulation regularity of “upper source-lower reservoir” type in this region remains unknown. In order to investigate these problems, a 2-D finite element model is established with regards to the fluid-solid coupling in Chegu 25 block of Chezhen depression, fully considering the existing seismic, logging data and regional tectonic stress environment. Meanwhile, we calculate the abnormal overpressure generated at the source rock during hydrocarbon generation and the process of hydrocarbon migration and accumulation along the faults, analyzing the dynamic conditions of hydrocarbon downward accumulation. The results show that overpressure can accelerate migration of hydrocarbon and improve the efficiency of hydrocarbon accumulation. However, when the overpressure is too large, tensile fractures and shear fractures may occur, resulting in hydrocarbon dissipation, and changing the results of oil and gas accumulation. The overpressure at the source rock is mainly caused by hydrocarbon generation, while the overpressure at the reservoir is primarily created by unbalanced compaction. As the dominant channel of hydrocarbon migration, overpressure will change the direction and path of hydrocarbon migration in the fault. Therefore, the “upper source-lower reservoir” hydrocarbon accumulation model is strongly explained by the high permeability of faults and the presence overpressure. In summary, the simulated overpressure results are in good agreement with the mud weight equivalent overpressure and the drill stem tests (DSTs).

Groundwater plays a crucial role in triggering and reactivating deep-seated landslides. However, classical hydrogeological investigations have limitations in their applicability to deep-seated landslides due to anisotropic and heterogeneous media[16]. The Huangtupo landslide in the Three Gorges reservoir area has garnered significant attention in China due to its large volume, complex geological structure, and high hazard potential. Recent monitoring data has shown notable deformation in the NO.1 Riverside Sliding Mass (HTP-1), one of the four parts of the Huangtupo landslide, making it the primary focus of landslide research. This study aimed to investigate the water sources in the HTP-1 landslide using environmental stable isotopes as tracers. The isotopic analysis results indicated that the groundwater in the landslide area (LGW) is a mixture of remote karst groundwater (KGW) from the adjacent up-slope and local precipitation (LP). The karst groundwater is a major contributor to the recharge of the landslide groundwater system, causing a high slope groundwater level that can easily exceed the critical level during heavy rainfall events. Furthermore, based on the differential distribution of the LP fraction of LGW at different locations, the groundwater in the landslide can be classified into three groups. Groundwater at the sliding rupture surface has the highest fractions of local precipitation, followed by the groundwater at the rear of the landslide. Combined with the monitoring data of groundwater level in boreholes during the rainy season, this indicates that fissures and fractures in the sliding rupture zone and at the back of the landslide are well connected, which could be a critical factor in the mass movement of the creeping slope.

The Coronavirus disease 2019 (COVID-19) rapidly spread to over 180 countries and abruptly disrupted the production rates and supply chains worldwide. Since then, 3D printing also recognized as additive manufacturing (AM) and known to be a novel technique that uses layer-by-layer deposition of material to produce the intricate 3D geometry, has been engaged in reducing the distress caused by the outbreak. During the early stages of this pandemic, shortages of Personal Protection Equipment (PPE), including facemasks, shields, respirators, and other medical gears, were significantly answered by remotely 3D printing them. Amidst the growing testing requirements, the 3D printing emerged as a potential and fast solution manufacturing process to meet the production needs due to its flexibility, reliability, and rapid response capabilities. In the recent past, some of the other medical applications that have gained prominence in the scientific community include 3D printed ventilator splitters, device components, and patient-specific products. Regarding the non-medical applications, researchers have successfully developed contact-free devices to address the sanitary crisis in public places. This work aims to systematically review the applications of 3D printing or AM techniques that have been involved in producing various critical products essential to limit this deadly pandemic's progression.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

We describe a novel machine that uses the greater-than-100% efficiency of air/ground-source heat pumps to recursively generate electricity via steam-powered generators, taking thermal energy from the ambient environment to convert into electrical power. The invention of a machines that generate clean power at low costs will be fundamental to the future of electricity. We estimate efficiency and calculate minimum efficiencies for unknown parts to consider the applicability of this machine to the real world.

3D printing is described as the third industrial revolution: its impact is global in industry and progresses every day in society. It presents a huge potential for ecology and evolution, sciences with a long tradition of inventing and creating objects for research, education and outreach. Its general principle as an additive manufacturing technique is relatively easy to understand: objects are created by adding material layers on top of each other. Although this may seem very straightforward on paper, it is much harder in the real world. Specific knowledge is indeed needed to successfully turn an idea into a real object, because of technical choices and limitations at each step of the implementation. This article aims at helping scientists to jump in the 3D printing revolution, by offering a hands-on guide to current 3D printing technology. We first give a brief overview of uses of 3D printing in ecology and evolution, then review the whole process of object creation, split into three steps: (1) obtaining the digital 3D model of the object of interest, (2) choosing the 3D printing technology and material best adapted to the requirements of its intended use, (3) pre- and post-processing the 3D object. We compare the main technologies available and their pros and cons according to the features and the use of the object to be printed. We give specific and key details in appendices, based on examples in ecology and evolution.

The combination of new-generation information technology and manufacturing technology has resulted in major and profound impact on future development paradigm of manufacturing. It is challenging for existing methods to conduct a multidimensional trend exploration related to machine tool domain, which is the basis of virtually everything in manufacturing. In this paper, we proposed an integrating approach framework combined topic models, bibliometric, trend analysis and patent analysis to mine insightful information about future development from multi-source data related to machine tool, such as papers, grants, patents and news. Specifically, papers and grants provided two different perspectives to explore the current focuses and future trends in machine tool research. Furthermore, the future technology development of machine tool was investigated through patents analysis. Finally, news related to machine tool industry in recent years was analyzed to analyze future machine tool business mode. The integration of the above various analytical methods and the multi-dimensional mining of literatures enabled the analysis of the future development of machine tool domain systematically from multi-perspectives which include research, technology development and industry. The conclusions obtained in this paper is beneficial to different communities of machine tool in terms of determining the research directions for researchers, identifying industry opportunities for corporations and developing reasonable industry policy for policy makers.

3D object reconstruction from depth image streams using Kinect-style depth cameras has been extensively studied. In this paper, we propose an approach for accurate camera tracking and volumetric dense surface reconstruction assuming a known cuboid reference object is present in the scene. Our contribu¬tion is three-fold. (a) We maintain drift-free camera pose tracking by incorporating the 3D geometric constraints of the cuboid reference object into the image registration process. (b) We reformulate the problem of depth stream fusion as a binary classification problem, enabling high-fidelity surface reconstruction, especially in the con¬cave zones of objects. (c) We further present a surface denoising strategy to mitigate the topological inconsistency (e.g., holes and dangling triangles), which facilitates the generation of a noise-free triangle mesh. We extend our public dataset CU3D with several new image sequences, test our algorithm on these sequences and quantitatively compare them with other state-of-the-art algorithms. Both our dataset and our algorithm are available as open-source content at https://github.com/zhangxaochen/CuFusion for oth-er researchers to reproduce and verify our results.

The urbanisation phenomenon and related cities expansion and transport networks entail preventing the increase of population exposed to environmental pollution. Regarding noise exposure, the Environmental Noise Directive demands on main metropolis to produce noise maps. While based on standard methods, these latter are usually generated by proprietary software and require numerous input data concerning, for example, the buildings, land use, transportation network and traffic. The present work describes an open source implementation of a noise mapping tool fully implemented in a Geographic Information System compliant with the Open Geospatial Consortium standards. This integration makes easier at once the formatting and harvesting of noise model input data, cartographic rendering and output data linkage with population data. An application is given for a French city, which consists in estimating the impact of road traffic-related scenarios in terms of population exposure to noise levels both in relation to a threshold value and level classes.

Centrifuges are commonly required devices in medical diagnostics facilities as well as scientific laboratories. Although there are commercial and open source centrifuges, costs of the former and required electricity to operate the latter, limit accessibility in resource-constrained settings. There is a need for low-cost, human-powered, verified and reliable lab-scale centrifuge. This study provides the designs for a low-cost 100% 3-D printed centrifuge, which can be fabricated on any low-cost RepRap-class fused filament fabrication (FFF) or fused particle fabrication (FPF)-based 3-D printer. In addition, validation procedures are provided using a web camera and free and open source software. This paper provides the complete open source plans including instructions for fabrication and operation for a hand-powered centrifuge. This study successfully tested and validated the instrument, which can be operated anywhere in the world with no electricity inputs obtaining a radial velocity of over 1750rpm and over 50N of relative centrifugal force. Using commercial filament the instrument costs about US$25, which is less than half of all commercially available systems; however, the costs can be dropped further using recycled plastics on open source systems for over 99% savings. The results are discussed in the contexts of resource-constrained medical and scientific facilities.

This paper presents a novel segmentation algorithm specially developed for applications in 3D point clouds with high variability and noise, particularly suitable for heritage building 3D data. The method can be categorized within the segmentation procedures based on edge detection. In addition, it uses a graph-based topo-logical structure generated from the supervoxelization of the 3D point clouds, which is used to make the clo-sure of the edge points and to define the different segments. The algorithm provides a valuable tool for generating results that can be used in subsequent classification tasks and broader computer applications dealing with 3D point clouds. One of the characteristics of this segmentation method is that it is unsupervised, which makes it particularly advantageous for heritage applications where labelled data is scarce. It is also easily adaptable to different edge point detection and supervoxelization algorithms. Finally, the results show that the 3D data can be segmented into different architectural elements, which is important for further classification or recognition. Extensive testing on real data from historic buildings demonstrates the effectiveness of the method. The results show superior performance compared to three other segmentation methods, both globally and in the segmentation of planar and curved zones of historic buildings.

Chronic kidney disease (CKD) is a progressive condition that affects more than 10% of the world's population. Monitoring urine albumin and creatinine ratio (µACR) has become the gold standard for nephropathy diagnosis and control. The objective of the present study was to develop a simple, accurate, sensitive, and rapid point-of-care test (PoCT) device - MYμALBUMIN that community healthcare professionals can use in resource-limited facilities and by patients in their own homes for screening the risk and monitoring the progress of CKD. Albumin and creatinine concentrations in urine samples were determined using spectrophotometric dye (tetrabromophenol blue)-binding and colorimetric Jaffe’assay, respectively. Urine samples were diluted with distilled water (1:80) and mixed separately with albumin and creatinine reaction mixture. The creatinine reaction was incubated at room temperature (25oC) for 30 minutes before analysis. Optical density (OD) was measured at the wavelengths of 625 nm (albumin) and 515 nm (creatinine). All calibration curves (2-60 mg/L and 0.25-2 mg/dL for albumin and creatinine) yielded linear relationships with correlation coefficients (r2) of &gt; 0.999. Good accuracy (%DMV &lt; + 2.88%) and precision (%CV &lt; 3.0%) were observed from both the intra- or interday assays for the determination of albumin and creatinine by MYµALBUMIN. The limit of quantification (LOQ) of albumin and creatinine in urine samples determined by MYµALBUMIN and laboratory spectrophotometer were 2 mg/L and 0.1 mg/dL, respectively, using 37.5 μL urine samples. The device was well applied with clinical samples from 13 CKD patients. The median (range) of %DMV of the central (hospital) laboratory method (immune-based assay) was 3.18 (-10.11 to 14.12)%, with a high correlation coefficient (r2 &gt;0.99). In conclusion, MYμALBUMIN showed satisfactory test performance in terms of accuracy, reproducibility, sensitivity, and specificity. The device would have significant economic benefits besides obviously improving clinical decision-making processes.

Accurate clinical diagnosis of patients presenting to primary care settings with acute sore throat remains challenging, often resulting in the over-prescribing of antibiotics. Using point-of-care tests (POCTs) to differentiate between respiratory infections is well-accepted, yet evidence on the application within primary care is sparse. We assessed the application of testing patients (n=160) from three family practices with suspected Streptococcal infections using rapid molecular tests (ID NOW Strep A2, Abbott). In addition to comparing clinical evaluation and prescription rates with either usual care or with testing, patients and staff completed a questionnaire about their experience of molecular POCT in primary care. The immediate availability of the result was important to patients (100%) and staff (≈90%) stated that molecular testing improved quality of care. Interestingly, only 22.73% of patients with a Centor score >2 tested positive for Strep A and overall, less than 50% of Centor scores 3 and 4 tested positive for Strep A with the ID NOW testing platform. The addition of rapid molecular POCTs to clinical assessment resulted in a 55- 65% reduction in immediate and deferred antibiotic prescriptions. The intervention was popular with patients and medical staff but was associated with increased cost and a longer appointment length.

This paper introduces a novel method for accurately calculating the upper biomass of single trees using Light Detection And Ranging (LiDAR) point cloud data. The proposed algorithm involves classifying the tree point cloud into two distinct ones: the trunk point cloud and the crown point cloud. Each part is then processed using specific techniques to create a 3D model and determine its volume. The trunk point cloud is segmented based on individual stems, with each stem further divided into slices that are modeled as cylinders. On the other hand, the crown point cloud is analyzed by calculating its footprint and gravity center. The footprint is further divided into angular sectors, with each being used to create a rotating surface around the vertical line passing through the gravity center. All models are represented in a matrix format, simplifying the process of minimizing and calculating the tree’s upper biomass, consisting of crown biomass and trunk biomass. To validate the proposed approach, both terrestrial and airborne datasets are utilized. A comparison with existing algorithms in the literature confirms the effectiveness of the new method. The study shows that the proposed algorithm achieves an average fit between 0.01 m and 0.49 m for individual trees.

This research focuses on the Hopf bifurcation occurring at a singular point with high-order degeneracy in a class of three-dimensional systems. Based on center manifold theorem, by expanding the technique for determining singular point values of degenerate singularities in two-dimensional systems, the formal series method to determine the singular point values at the high-order degenerate critical point is discussed. Furthermore, a class of specific three-dimensional differential systems with high-order degenerate singularities is explored. By computing the singular point values and determining center conditions, we proved that a minimum of 5 small-amplitude limit cycles in the vicinity of the origin. This research provides new perspectives on the center problem and limit cycle bifurcation in high-dimensional systems with high-order degenerate singular points.

Interactions between mobile robots and human operators in common areas require a high safety especially in terms of trajectory planning, obstacle avoidance and mutual cooperation. In this connection the crossings of planned trajectories, their uncertainty based on model fluctuations, system noise and sensor noise,play an outstanding role. This paper discusses the calculation of expected areas of interactions du ring human-robot navigation with respect to fuzzy and noisy information. Expected crossing points of possible trajectories are nonlinearily associated with positions and orientations of robot and human. The nonlinear transformation of a noisy system input, such as directions of motion of human and robot, to a system output, the expected area of intersection of their trajectories, is done by two methods: statistical linearization and the sigma-point-transformation. For both approaches fuzzy approximations are presented and the inverse problem is discussed where the input distribution parameters are computed from given output distribution parameters.

Point defects induced by doping rare earth elements RE (Nd, Er) into the magnesium oxide host were investigated by classical atomistic simulations utilising the General Utility Lattice Program (GULP). Formation and association energies were calculated for the potential defect structures. Both isolated defects and defect complexes were considered. The most energetically favourable structures of defect complexes were found for rare earth doped and Li co-doped systems. The correlation between the association energy and the structure of the defect complex was investigated. The influences of Li were revealed with respect to energy and structure. The simulation results contribute to the understanding of the point defects of doped MgO and how Li influences the doping of rare earth elements in the MgO host.

Accurate classification of objects in 3D point clouds is a significant problem in several applications, such as autonomous navigation and augmented/virtual reality scenarios, which has become a research hot spot. In this paper, we presented a deep learning strategy for 3D object classification in augmented reality. The proposed approach is a combination of the GRU and LSTM. LSTM networks learn longer dependencies well, but due to the number of gates, it takes longer to train; on the other hand, GRU networks have a weaker performance than LSTM, but their training speed is much higher than GRU, which is The speed is due to its fewer gates. The proposed approach used the combination of speed and accuracy of these two networks. The proposed approach achieved an accuracy of 0.99 in the 4,499,0641 points dataset, which includes eight classes (unlabeled, man-made terrain, natural terrain, high vegetation, low vegetation, buildings, hardscape, scanning artifacts, cars). Meanwhile, the traditional machine learning approaches could achieve a maximum accuracy of 0.9489 in the best case.

We investigated the development of a simple and sensitive assay for the identification of minute amounts of animal and human biological material. The suggested system uses isothermal amplification of DNA in a rapid assay format, which returns the results in as little as 40 minutes from sampling. The assay used for the proof of concept employs the novel handheld SaLux19 device (Max-Planck Innovation prototype, Germany). This well-established infield detection system could also be utilized for forensic scenarios. The results presented here demonstrated that the assay is sufficiently specific and sensitive and can detect the presence of Sus scrofa nucleic acids.

Precise individual tree or sample-based inventories derived from 3D point cloud data of mobile laser scanning can improve our comprehensive understanding of the structure, function, resilience, biodiversity, and ecosystem services of urban forests. This study assessed the performance of a hand-held laser scanning system for the extraction of tree position, diameter at breast height (DBH) and tree height (H) in an urban area. A total of 2083 trees of 13 species from 34 plots were analyzed. The results showed that the registration of tree positions using ground control points (GCPs) demonstrated high accuracy, with errors consistently below 0.4 m, except for a few instances. The extraction accuracy of DBH for all trees and individual species remained consistently high, with a total root mean square error (RMSE) of 2.06 cm (6.89%) and a bias of 0.62 cm (2.07%). Notably, broad-leaved trees outperformed coniferous trees, with RMSE and bias values of 1.86 cm (6%) and 0.76 cm (2.46%) compared to 2.54 cm (9.46%) and 0.23 cm (0.84%). Tree height extraction accuracy varied significantly among different species, with R2 values ranging from 0.65 to 0.92. Generally, both DBH and height were underestimated. Linear mixed effects models (LME) were applied to evaluate factors affecting the performance of HLS with the plot as a random factor. LME analysis revealed that plant type and terrain significantly influenced the accuracy of DBH and H derived from HLS data. Other fixed factors of plot area, tree density and trajectory length didn’t have significance. With a large sample size, we concluded that the HLS demonstrated sufficient accuracy in extracting individual tree parameters in urban forests.

The most commonly used real-time augmentation services in China are International GNSS Service (IGS) real-time service, PPP-B2b service, and BeiDou Satellite-Based Augmentation System (BDSBAS) dual-frequency augmentation service. However, the research on the performance evaluation, comparison and application scope of these three products is still unknown and unrevealed. This article introduces methods for obtaining real-time augmentation information and real-time orbit and clock offset recovery. Based on real-time orbit and clock offset accuracy, positioning accuracy, and positioning availability, it systematically evaluates the performance of CNES, PPP-B2b, and BDSBAS augmentation information. The results indicate that the radial accuracy of CNES and PPP-B2b real-time orbit products is consistent, and the Root Mean Square (RMS) is better than 5 cm. CNES can achieve centimeter-level accuracy in both along-track and cross-track components, surpassing the decimeter-level accuracy of PPP-B2b. Both services demonstrate consistent accuracy in real-time clock offset, with PPP-B2b showing similar standard deviations (STD) of 0.16 ns for different satellites. However, for CNES, the STD of real-time clock offset varies for GPS, BDS-3 MEO, and BDS-3 IGSO satellites, with values of 0.10 ns, 0.19 ns, and 0.60 ns, respectively. The accuracy and availability of the two PPP services exhibit the same levels, with centimeter-level accuracy achieved after convergence and positioning availability exceeding 99%. Therefore, the difference between the two services in application areas depends on the acquisition of augmentation information. However, BDSBAS, which concentrates on code observations, demonstrates lower accuracy in real-time orbit and clock offset, positioning accuracy, and positioning availability compared to the other two services. Its primary application is in the aviation and maritime domains, where there is a greater need for service integrity, continuity, and reliability.

Rational delineation of urban–rural boundaries is a foundational prerequisite for holistic urban and rural development planning and rational resource allocation. However, the results of division of urban–rural boundaries extracted using a single data source are non-comprehensive. To address this problem, the present study proposes a method for using multiple sources such as population data, nighttime light data, land use, and points of interest (POI) data to extract urban–rural boundaries. Considering Guizhou Province for a case study, we here present a two-step method for identifying urban–rural boundaries. First, the random forest model was combined with the dasymetric mapping method to obtain the population spatialization data with a 30-m resolution in the studied province. Second, using the breaking point method, we extracted the urban–rural boundary for Guizhou Province in 2020 based on the spatialized population. This method fully integrated the benefits of various data and judiciously extracted the boundaries of the main urban areas and small- and medium-sized towns of each city in the study province at the same spatial scale. The stratified random sampling method revealed that the average overall accuracy was 88.05%. The method proposed has certain universality and application value and allows identifying the urban–rural boundaries more accurately and practically.

The management and classification of solid waste is one of the most important challenges around the world, in order to sustain economic growth and preserve the environment. The objective is to propose the use of Smart Ecological Points as a strategy to address the problem related to the solid waste management system at the source, which has become one of the biggest problems globally and Colombia is no exception. The article describes the current state of the problem in the country and in turn, presents the possibility of developing a prototype corresponding to a low-cost Smart Ecological Point supported by the use of an experimental capacitive sensor and Machine Learning algorithms, which will reduce the time necessary for the classification of recyclable and non recyclable waste, minimizing the health risks and increasing the percentage of waste that can be reused, by reducing the probability of being contaminated at the source, an aspect that is very common when done manually. According to the results obtained, it was evident that the proposed prototype made an adequate classification of waste, generating the possibility of being manufactured with existing technology in the environment, in order to promote adequate waste classification at the source.

Although relatively rare, affecting 8% of the general population, autoimmune disorders are causative linked with chronic diseases and morbidity. Control of the course of the disease is closely dependent on the ability to monitor its onset as well as response to treatment. In the present report, we review the progress in the development of biosensor-based approaches and related tools for the Point-of-Care diagnosis and monitoring of biomarkers related to several autoimmune diseases, such as Myasthenia Gravis, Rheumatoid Arthritis, Multiple Sclerosis, Systemic Erythematosus Lupus, Crohn’s Disease, Diabetes Mellitus, Behcet’s disease, Psoriasis and Celiac Disease. Various biosensing technologies are discussed, including electrochemical, optical and mechanical ones, along with the use of advanced nanomaterials and immobilization techniques for the biorecognition elements. The need for innovative devices with unique features of rapid, low-cost, real-time detection is considered in the context of preventing permanent organ and tissue damage from chronic autoimmune diseases.

High-precision ground point cloud data has a wide range of applications in various fields, and the separation of ground points from non-ground points is a crucial preprocessing step. Therefore, designing an efficient, accurate, and stable ground extraction algorithm is of great significance for improving the processing efficiency and analysis accuracy of point cloud data. The study area in this article was a Park in Guilin, Guangxi, China. The point cloud was obtained by utilizing the UAV platform. In order to improve the stability and accuracy of the Filter algorithm, this article proposed a triangular grid filter based on Slope Filter, found violation points by the spatial position relationship within each point in the triangulation network, improved KD-Tree-Based Euclidean Clustering, and applied it to the non-ground points extraction, this method has good accuracy, stability and achieves good results in separating ground points from non-ground points. At first, using Slope Filter to remove some non-ground points, to reduce the error of taking ground points as non-ground points; Secondly, established a triangular grid based on the triangular relationship between each point, the violation-triangle can determin through the grid, and then the corresponding violation points were found in the violation-triangle; Thirdly, according to the three-point collinear method to extract the regular points, used these points to extract the regular landmarks by KD-Tree-Based Euclidean Clustering and Convex Hull Algorithm; Finally, removed disperse points and irregular landmarks by Clustering Algorithm. In order to confirm the superiority of this algorithm, this article compared the filter effects of various algorithms on the study area and filtered the 15 sample data provided by ISPRS, and obtained an average error of 3. 46%. The results showed that the algorithm in this article have a high processing efficiency and accuracy, which can greatly improve the processing efficiency of point cloud data in practical applications.

3D point cloud classification tasks have been a hot topic in recent years. Most existing point cloud processing frameworks lack context-aware features due to the deficiency of sufficient local feature extraction information. Therefore, we design an augmented sampling and grouping (ASG) module to efficiently obtain fine-grained features from the original point cloud. In particular, this method strengthens the domain near each centroid and makes reasonable use of the local mean and global standard deviation to mine point cloud’s local and global features. In addition to this, inspired by the transformer structure UFO-ViT in 2D vision tasks, we first try to use a linearly-normalized attention mechanism in point cloud processing tasks, investigating a novel transformer-based point cloud classification architecture UFO-Net. An effective local feature learning module is adopted as a bridging technique to connect different feature extraction modules. Importantly, UFO-Net employs multiple stacked blocks to better capture feature representation of the point cloud. Extensive ablation experiments on public datasets show that our method outperforms other state-of-the-art methods. For instance, our network performed with 93.7% overall accuracy on the ModelNet40 dataset, which was 0.5% higher than PCT. Our network also archived 83.8% overall accuracy on the ScanObjectNN dataset, which is 3.8% better than PCT.

The paper's main goal is to introduce a novel type of interpolative convex contraction and build up some fresh findings for it using the interpolative convex contractions' progressive approach. We have established certain conclusions using orbitally S-complete and Suzuki type contractions in F-metric spaces. My research aims to examine the fixed point method's efficacy in solving fractional differential equation with boundary conditions.

Spatial approach based on the deformation measurement of volcanic dome and crater rim is key to evaluate the activity of a volcano, such as Merapi volcano where associated disaster risk is regularly taking lives. Within this framework, this study aime to detect localized deformation and change in the summit area that has occurred concomitantly with the dome growth and explosion reported. The methodology was focused on two sets of data, one LiDAR-based dataset of 2012 and one UAV-dataset of 2014. The results show that during the period 2012-2014, the crater walls are 100 m to 120 m high above the crater floor at its maximum (North to East-South-East sector), while the West and North sector presents a topographic range of 40 to 80 m. During the period 2012 – 2014, the evolution of the crater rim around the dome is generally stable (no large collapse). The opening of a new vent on the surface of the dome has displaced an equivalent volume of 2.04 E+04 m3 corresponding to a maximum -9 m (+/- 0.9 m) vertically. This concludes that during the period 2012 – 2014 when the dome of Merapi experienced phreatic or phreatomagmatic explosions, the topography around the dome rose. This rise does not seem to be related to large wall collapses, and it is likely that modification in the subsurface have triggered those changes.

Accumulated data show the utility of diagnostic multi-organ point-of-care ultrasound (PoCUS) in the assessment of patients admitted to an internal medicine ward. Assess whether multi-organ PoCUS (lung, cardiac, and abdomen) provides relevant diagnostic and/or therapeutic information in patients admitted for any reason to an internal medicine ward. Prospective, observational, and single-center study, at a secondary hospital. Multi-organ PoCUS was performed during the first 24 hours of admission. The sonographer had access to the patients’ medical history, physical examination, and basic complementary tests performed in the ED (laboratory, X-ray, electrocardiogram). We considered a relevant ultrasound finding if it implied a significant diagnostic and/or therapeutic change. In the second semester of 2019, 310 patients were enrolled (48.7% men, mean age 70.5 years). Relevant ultrasound findings were detected in 86 patients (27.7%) and in 60 (19.3%) triggered a therapeutic change. These findings were associated with older age (Mantel-Haenszel 2 = 25.6; p&lt; .001) and higher degree of dependency (Mantel Haenszel 2 = 5.7; p = .017). Multi-organ PoCUS provides relevant diagnostic information, complementing traditional physical exam, and facilitates therapy adjustment, regardless of the cause of admission. Multi-organ PoCUS to be useful need to be systematically integrated into the decision-making process in internal medicine.

The ACC feature when activated augments the engine performance in real-time. This article presents a novel methodology to predict the optimal adaptive cruise control set speed profile (ACCSSP) by considering all the effecting parameters. This paper investigates engine operating conditions (EOC) criteria to develop a predictive model of ACCSSP in real-time. We developed a deep learning (DL) model using the NARX method to predict engine operating point (EOP) mapping the vehicle-level vectors (VLV). We used real-world field data obtained from Cadillac test vehicles driven by activating the ACC feature for developing the DL model. We used a realistic set of assumptions to estimate the VLV for the future time steps for the range of allowable speed values and applied them at the input of the developed DL model to generate multiple sets of EOP’s. We imposed the defined EOC criteria on these EOPs, and the top three modes of speeds satisfying all the requirements are derived for each second. Thus three eligible speed values are estimated for each second, and an additional criterion is defined to generate a unique ACCSSP for future time steps. Performance comparison between predicted and constant ACCSSPs indicates that the predictive model outperforms constant ACCSSP.

General relativity is a theory for gravitation based on Riemannian geometry, difficult to compatibilize with quantum mechanics. This is evident in relativistic problems in which quantum effects cannot be discarded. For example in quantum gravity, gravitation of zero-point energy or events close to a black hole singularity. Here, we set up a mathematical model to select general relativity geodesics according to compatibility with the uncertainty principle. To achieve this, we derived a geometric expression of the uncertainty principle (GeUP). This formulation identified proper space-time length with Planck length by a geodesic-derived scalar. GeUP imposed a minimum allowed value for the interval of proper space-time which depended on the particular space-time geometry. GeUP forced the introduction of a “zero-point” curvature perturbation over flat Minkowski space, caused exclusively by quantum uncertainty but not to gravitation. When applied to the Schwarzschild metric and choosing radial-dependent geodesics, our mathematical model identified a particle exclusion zone close to the singularity, similar to calculations by loop quantum gravity. For a 2 black hole merger, this exclusion zone was shown to have a radius that cannot go below a value proportional to the energy/mass of the incoming black hole multiplied by Planck length.

In this paper, by using the variational method, a sufficient condition for the unique existence of the stationary solution of the reaction-diffusion ecosystem is obtained, which directly leads to the global asymptotic stability of the unique equilibrium point. Besides, employing impulse control technique derives the globally exponential stability criterion of delayed feedback ecosystem.And numerical examples illuminate the effectiveness of impulse control, which has a certain enlightening effect on the actual epidemic prevention work . That is, in the face of the epidemic situation, taking a certain frequency of positive and effective epidemic prevention measures is conducive to the stability and control of the epidemic situation. particularly, the newly-obtained theorems quantifies this feasible step.

This paper introduces a method for tunnel point cloud and BIM model integration and cross-section monitoring, providing information to analyse tunnel cross-sections and surrounding rock deformation, and support for tunnel maintenance and reconstruction. Three types of data are processed for the integration: laser scanning point cloud, BIM tunnel model and terrain model from oblique photogrammetry. An adaptive BIM modelling scheme is proposed for tunnels with alien structures. Precise spatial registration of the data sets is conducted by applying singular value decomposition (SVD) algorithm to calculate transformation parameters from the point cloud model to the BIM model. Since the tunnel central line has high-order derivability, a cross-section calculation method based on tangent vector is proposed to obtain the cross-sectional profile of tunnels at any mileage. The proposed method has been verified by applying it to a tunnel reconstruction project. The experiment results show that the tunnel point cloud and the BIM model were highly coincident after the integration. The developed program can effectively get the cross-section of the tunnel at any mileage, and correctly express the spatial relationship between the BIM tunnel, the point cloud of tunnel and the external mountainous terrain.

The ongoing pandemic of COVID-19 has not only commenced a global health emergency but agitated various aspects of humanity. During this period of crisis researchers over the world have ramped their efforts to constrain the disease in all possible ways whether it is vaccination, therapy, or diagnosis. Since the spread of the disease has not yet elapsed sharing the ongoing research findings could be the key to disease control and management. An early and efficient diagnosis could leverage the outcome until a successful vaccine is developed. Molecular tests both in-house and commercial kits are preferably being used worldwide in the COVID-19 diagnosis. However, the limitation of high prices and lengthy procedures impede their use for mass testing. Keeping the constant rise of infection in mind search for an alternative test that should be cost-effective, simple, and suitable for large scale testing and surveillance is a need of an hour. One such alternative could be the immunological tests. Therefore, in the last few months deluge of immunological rapid tests has been developed and validated across the globe. The objective of the present review is to share the diagnostic performance of various immunological assays reported so far in SARS-CoV-2 case detection. The article consolidated the studies (published and preprints) related to the serological tests such as chemiluminescence, enzyme-linked and lateral flow-based point-of-care tests in COVID-19 diagnosis and updated the current scenario. This review will hopefully be an add-on in COVID-19 research and will contribute to congregate the evidence for decision-making.

The current coronavirus disease 2019 (COVID-19) pandemic is largely driven by community transmission, after 2019 novel Coronavirus (2019-nCoV or SARS-CoV-2) crosses the borders. To stop the spread, rapid testing is required at community clinics and hospitals. These rapid tests should be comparable with the standard PCR technology. Isothermal amplification technology provides an excellent alternative that is highly amenable to resource limited settings, where expertise and infrastructure to support PCR are not available. In this review, we provide a brief description of isothermal amplification technology, its potential and the gaps that need to be considered for SARS-CoV-2 detection. Among this emerging technology, loop mediated amplification (LAMP) and recombinase polymerase amplification (RPA) technologies have been identified as potential platforms that could be implemented at community level, without samples referral to a centralised laboratory and prolonged turn-around-time associated with the standard COVID-19 RT-PCR test. LAMP, for example, has recently been shown to be comparable with PCR and could be performed in less than 30 min by non-laboratory staff, without RNA extractions commonly associated with PCR. More so, it is cost effective and could easily be scaled up to resource limited settings. Diagnostics developers, scientific community and commercial companies could consider this alternative method to help stop the spread of COVID-19.

Background: In recent years, the abusive use of the smartphone has reached a situation that could be considered pathological, although there is no such classification in the DSM-IV. In this sense, different instruments to assess this problematic use or addiction to the smartphone are used. Among them, we found the SPAI, which has been validated in the Spanish language. The main difficulty of these scales is to establish a cut-off point that determines such mobile addiction. On the other hand, self-perception has been used in different addictions as a predictor of the problem. Aim: The objective of this study is to establish the cutting point in the scores of the SPAI scale validated in Spanish, using as a referent the self-perception of addiction values. Methods: A receiver operating characteristics (ROC) analysis was carried out, establishing as the cut-off point the one that presented a higher value of Youden J, indicative of its sensitivity and specificity. Results: 2598 participants from the university community completed the SPAI-Spain questionnaire. When using the self-perception of smartphone addiction as the benchmark value, a score of 44 has been established as the cutting point of the SPAI questionnaire, with a Youden J corresponding to 0.416. Conclusions: The implementation of a cut-off point of the SPAI questionnaire makes it an instrument that allows early identification of those individuals at risk of addiction as well as the establishment of preventive and/or intervention measures.

We present an improved algorithm for fast calculation of the inverse square root for single-precision floating-point numbers. The algorithm is much more accurate than the famous fast inverse square root algorithm and has a similar computational cost. The presented modification concern Newton-Raphson corrections and can be applied when the distribution of these corrections is not symmetric (for instance, in our case they are always negative).

New developments in broadcast technology, such as the ad hoc wireless network and the detection devices that work, enable daily connections to the Internet, commonly referred to as the Internet of Things (IoT). IoT saw this as a support for the development of creative and contextual services and applications. The service can respond to the user's environment and preferences. Finite state machines are recently making waves when the issue of self-controlling systems come into the picture of designs. This research focuses on the design of a fault tolerant system that controls random failures impressed on the network. The method comprises of diodes, Resistors, Optocouplers, ESP8266 WI-FI Module Webpage with button, and two Arduinos which in effect will determine iteratively who to handle a failure at hand modelled as when the button on the webpage is pressed. In this work, a Heartbeat Detection and Monitoring System will be made using Arduino that detect the electrical state using the Pulse Sensor and show the readings in Beats Per Minute on the LED connected a microcontroller. It sends the texts to the server using the Wi-Fi module ESP8266 to signals can be monitored from the monitoring zone via the internet. This is reflected by the declaration of a master state by either of two Arduinos whenever the push button is pressed as observed on the codes. The result obtained from the research shows apparently, the state of the fault tolerance system none power deny of heartbeat condition connected to the LED.

To determine the photon emission or absorption probability for a diatomic system in the context of the semiclassical approximation it is necessary to calculate the characteristic canonical oscillatory integral which has one or more saddle points. Integrals like that appear in a whole range of physical problems, e.g. the atom-atom and atom-surface scattering and various optical phenomena. A uniform approximation of the integral, based on the stationary phase method is proposed, where the integral with several saddle points is replaced by a sum of integrals each having only one or at most two real saddle points and is easily soluble. In this way we formally reduce the codimension in canonical integrals of "elementary catastrophes" with codimensions greater than 1. The validity of the proposed method was tested on examples of integrals with three saddle points ("cusp" catastrophe) and four saddle points ("swallow-tail" catastrophe).

The aim of this article is to extend the local as well as the semi-local convergence analysis of multi-point iterative methods using center Lipschitz conditions in combination with our idea, of the restricted convergence region. It turns out that this way a finer convergence analysis for these methods is obtained than in earlier works and without additional hypotheses. Numerical examples favoring our technique over earlier ones completes this article.

We consider Pisot family substitution tilings in $\R^d$ whose dynamical spectrum is pure point. There are two cut-and-project schemes(CPS) which arise naturally: one from the Pisot family property and the other from the pure point spectrum respectively. The first CPS has an internal space $\R^m$ for some integer $m \in \N$ defined from the Pisot family property, and the second CPS has an internal space $H$ which is an abstract space defined from the property of the pure point spectrum. However it is not known how these two CPS's are related. Here we provide a sufficient condition to make a connection between the two CPS's. In the case of Pisot unimodular substitution tiling in $\R$, the two CPS's turn out to be same due to [5, Remark 18.5].

In this paper, we introduced many new notions and new contraction named as S-weakly contraction after that we obtained the p-common best proximity point theorems for different types of contractions in the setting of complete metric spaces by using weak P_p-property and proved the uniqueness of these points. Also we presented some examples to prove the validity of our results.

The sustainability of irrigated agriculture depends on the quality of irrigation water used. The electrolyte concentration (EC) of irrigation water may lead to the accumulation of salts in the root zone layers and affect the physiological functions of the crop by osmotic and ion toxicity effects. Further, the cationic and anionic composition of the water may alter the exchangeable cation composition of the soil and as well as its pH. Because of the dominance of sodium salts in many sources of irrigation water, parameters related to sodium such as exchangeable sodium percentage (ESP) of soils and sodium adsorption ratio (SAR) of soil solutions have been commonly used to study the effects of sodium in irrigation water on soil structural stability. Quirk and Schofield concept of ‘threshold electrolyte concentration’ (TEC) has shown the importance of electrolytes in preventing the effects of sodium on soil structure. Based on this concept, several models have been proposed to relate ESP or SAR with EC to predict the possible impacts of irrigation water on soil structural stability. However, many research reports indicate that this relationship varies with soils and a given model is not suitable for all types of soils. Further, the effects of potassium and magnesium in the processes leading to clay dispersion are disregarded in these models. This essay analyses all the factors involved in the structural failure of soils with different cationic composition, identify the defects in these TEC models and re-defines TEC on the basis of new insights on dispersive and flocculating charges of soils. This review does not deal with EC effects on crops and also the role of contaminant ions not involved with soil structural stability.

Filamentous fungi such as Aspergillus spp. are opportunistic pathogens, which cause highly invasive infections, especially in immunocompromised individuals. Control of such fungal pathogens is increasingly problematic due to the small number of effective drugs available for treatment. Moreover, the increased incidence of fungal resistance to antifungal agents makes this problem a global human health issue. The cell wall integrity system of fungi is the target of antimycotic drugs echinocandins, such as caspofungin (CAS). However, echinocandins cannot completely inhibit the growth of filamentous fungal pathogens, which results in survival/escape of fungi during treatment. Chemosensitization was developed as an alternative intervention strategy, where co-application of CAS with the intervention catalyst octyl gallate (OG; chemosensitizer) greatly enhanced CAS efficacy, thus achieved ≥ 99.9% elimination of filamentous fungi in vitro. Based on hypersensitive responses of Aspergillus antioxidant mutants to OG, it is hypothesized that, besides destabilizing cell wall integrity, the redox-active characteristic of OG may further debilitate fungal antioxidant system.

The safe and reliable operation of autonomous vehicles in complex and dynamic environments is heavily dependent upon exteroceptive and proprioceptive sensors. A LiDAR system generates accurate 3D point clouds, which are crucial for the detection, classification, and tracking of multiple targets. LiDAR data, however, presents significant challenges due to its density, noise, and varying sampling rates. In this study, various clustering and MTT techniques for LiDAR point clouds will be identified and classified within the context of autonomous driving to assess the state-of-the-art methods’ key challenges and their performances. We have categorized clustering and MTT methods used in AV applications, identified research gaps and challenges and analyzed existing algorithms and their challenges in detail. Researchers and practitioners in the field of autonomous driving will find this review to be a valuable resource.

Researchers are exploring solutions to meet the growing demand for protein due to the expected increase in global population by 2050. Interest in alternative protein sources like insects has risen, driven by concerns about environmental impact and the need for sustainable food production. This study aimed to develop and evaluate the physicochemical properties of soy protein-based burger enriched with insect protein from Alphitobius diaperinus. Three formulations were developed: a control (B0), and burgers with 5% (B5) and 10% (B10) insect protein - Whole Buffalo Powder (WBP). Results showed that adding insect protein decreased the burger analogue's pH. There was observed a clear trend of increasing total lipids and SFA, and decreasing MUFA and PUFA, as the WBP concentration increases from 0% to 10%. No significant differences with increasing WBP concentration in the protein content of the burger analogue, as well as the cooking yield, were noted. The WBP addition had a notable effect on the color change, especially decrease in brightness (L*). It was shown that as the WBP concentration increased, there were no significant differences in the texture profile of the burger analogues. The formulation with 5% WBP concentration was the most acceptable in sensory analysis.

This study introduces a low-cost solution provided by a specialized source measure unit (SMU), offering an alternative to conventional source meter units. Through precise IV curve measurements for graphene-channel FETs, the SMU demonstrates its capability in accurately characterizing these devices with minimal noise and high accuracy. This cost-effective solution presents a promising avenue for researchers and developers seeking reliable tools for sensor development and characterization, providing valuable insights into the behavior of graphene-channel FETs and the effect of surface illumination without the need for expensive equipment. Additionally, the SMU was validated with known passive and active components, along with probe station integration for microscale connection, ensuring its effectiveness in capturing accurate measurements. The SMU’s focus on collecting IV curves, coupled with its ability to identify device defects, such as Schottky junctions, contributes to its utility in quality testing for semiconductor devices. Its low-cost nature makes it accessible for various research endeavors, enabling efficient data collection and analysis for graphene-based sensor applications.

The escalation of mining activities in the karst regions of Guizhou Province has heightened the occurrence of water-inrush incidents in deep coal mines. This study focused on water-inrush phenomena within the Xinhua mining area of Jinsha County, Guizhou Province, aiming to investigate the sources of these incidents. The findings indicated that the overlying limestone of the Changxing Formation in the coal seam served as a vulnerable aquifer under certain conditions, leading to water inrushes. The analysis of the spatiotemporal distribution patterns of water-inrush incidents at the working face indicated that previous mining operations damaged the shallow Changxing Formation limestone, resulting in the accumulation of goaf water and the formation of numerous mining-induced fractures. These fractures served as rapid conduits for water inrushes from both atmospheric precipitation and underground sources at the deep working face. The examination of surface water and mine water quality demonstrated that both exhibited similar characteristics, predominantly featuring bicarbonate, sulfate, and sodium compositions. Investigation into the relationship between mine water inflow and atmospheric precipitation established that atmospheric precipitation influenced the mine water supply cycle, with a replenishment period of ~10 months during the operational phase of the Jinyuan Coal Mine and about one month post-closure. The fractures induced by mining activities within the Changxing Formation limestone facilitated water flow, with atmospheric precipitation serving as the primary water source for the mine. This study offered a valuable scientific foundation for addressing water-related damage resulting from atmospheric precipitation in mines susceptible to water inrushes under analogous hydrogeological conditions.

Infrared small target detection (ISTD) plays a crucial role in both civilian and military applications. The detection of small targets against dense cluttered backgrounds remains a challenging task, requiring the collaboration of false alarm source elimination and target detection. Existing approaches primarily focus on modeling targets while often neglecting false alarm sources. To address this limitation, we propose a Target and False Alarm Collaborative Detection Network to leverage the information provided by false alarm sources and the background. Firstly, we introduce a False Alarm Source Estimation Block (FEB) that estimates potential interferences present in the background by extracting features on multiple scales and employing stepwise upsampling for feature fusion. Subsequently, we propose a framework that employs multiple FEBs to eliminate false alarm sources across multiple scales. Finally, a Target Segmentation Block (TSB) is introduced to accurately segment the targets to produce the final detection result. Experiments on public datasets demonstrate that, compared to other methods, our model achieves high accuracy in segmenting targets while being able to extract false alarm sources which can be used for further studies.

This study employs the FLACS code to analyze hydrogen leakage, vapor dispersion, and subsequent explosions. Utilizing pseudo-source models, a liquid pool model, and a hybrid model combining both, we investigate dispersion processes for varying leak mass flow rates (0.225 kg/s and 0.73 kg/s) in a large open space. We also evaluate explosion hazards based on overpressure and impulse effects on humans. The computational results, compared with experimental data, demonstrated reasonable hydrogen vapor cloud concentration predictions, especially aligned with the wind direction. For higher mass flow rate of 0.73 kg/s, the pseudo-source model and hybrid model proved appropriate, while the liquid pool model was more suitable for lower mass flow rate of 0.225 kg/s. Regarding explosion analyses using overpressure-impulse diagram, higher mass flow rates leaded to potentially fatal overpressure and impulse effects on humans. However, lower mass flow rates may cause severe eardrum damage at the maximum overpressure point.

Aiming at the difficult problem of broadband oscillation localization in power systems, the intel-ligent localization method of oscillation source based on the digital twin is proposed and the os-cillation source localization system based on the digital twin is constructed. Firstly, a digital twin-based oscillation source localization method and system architecture are proposed. Fur-thermore, an intelligent positioning method of oscillation source based on data-driven and mechanism fusion is proposed. It includes three steps: oscillation signal preprocessing, oscillation modal analysis and oscillation source localization. For the oscillation signal preprocessing, the generative adversarial imputation network is used to repair the missing samples, and the su-per-resolution technique is used to realize the super-resolution measurement of broadband os-cillation. In the oscillation modal analysis, the spectrum of the oscillation signal is extracted using the fast Fourier transform. To accurately locate the oscillation source, the branch potential energy is used as input to the data-driven model, such as LSTM and CNN. Finally, an oscillation source localization system is developed based on the digital twin workshop CloudPSS-XStudio, which can locate the oscillation source quickly and accurately.

It is a challenging and meaningful task to carry out drone-based livestock monitoring in high-altitude and cold regions. The purpose of AI is to execute automated tasks and to solve practical problems in actual applications by combining the software technology with the hardware carrier to create integrated advanced devices. Only in this way, the maximum value of AI could be realized. In this paper, a real-time tracking system with dynamic target tracking ability is proposed. It is developed based on the tracking-by-detection architecture using YOLOv7 and DeepSORT algorithms for target detection and tracking, respectively. To address the existing problems of the DeepSORT algorithm, the following two optimizations are made: (1) Optical flow is used to compensate the Kalman filter for improvement of the prediction accuracy; (2) A low-confidence trajectory filtering method is adopted to reduce the influence of unreliable detection on target tracking. In addition, an visual servo controller for the UAV is designed to enable the automated tracking task. Finally, the system is tested using the Tibetan yaks living in the Tibetan Plateau as the tracking targets, and the results reveal the real-time multiple tracking ability and the ideal visual servo effect of the proposed system.

In a context of exponential demographic growth, the imbalance between human resources and public health problems is impelling us to envision other solutions to the difficulties faced in the diagnosis, prevention and large-scale management of the most common diseases. Cardiovascular diseases represent the leading cause of morbidity and mortality worldwide. A large-scale screening program would make it possible to promptly identify patients with high cardiovascular risk in order to manage them adequately. Optical coherence tomography-angiography (OCT-A), as a window into the state of the cardiovascular system, is a rapid, reliable, and reproducible imaging examination that enables prompt identification of at-risk patients through the use of automated classification models. One challenge that limits the development of computer-aided diagnostic programs is the small number of open-source OCT-A acquisitions available. To facilitate the development of such models, we have assembled a set of images of the retinal microvascular system from 499 patients. It consists of 814 angiocubes as well as 2005 en face images. Angiocubes were captured with a swept-source OCT-A device of patients with varying overall cardiovascular risk. To the best of our knowledge, our dataset, RASTA, is the only publicly available dataset comprising such a variety of images from healthy and at-risk patients. This dataset will enable the development of generalizable models for screening of cardiovascular diseases from OCT-A retinal images.

Electrical impedance tomography (EIT) can monitor the real-time hemodynamic state of a conscious and spontaneously breathing patient noninvasively. However, cardiac volume signal (CVS) extracted from EIT images has a small amplitude and is sensitive to motion artifacts (MAs). This study aimed to develop a new algorithm to reduce MAs from the CVS for more accurate heart rate (HR) and cardiac output (CO) monitoring in patients undergoing hemodialysis based on the source consistency between the electrocardiogram (ECG) and the CVS of heartbeats. Two signals were measured at different locations on the body through independent instruments and electrodes, but the frequency and phase were matched when no MAs. As the number of motions per hour (MI) increased over 30, the proposed algorithm had a correlation of 0.83 and a precision of 1.65 beats per minute (BPM) compared to the conventional statical algorithm of a correlation of 0.56 and a precision of 4.04 BPM. For CO monitoring, the precision and upper limit of the mean ∆CO were 3.41 and 2.82 liters per minute (LPM), respectively, compared to 4.05 and 3.82 LPM of the statistical algorithm. The developed algorithm could reduce MAs and improve HR/CO monitoring accuracy and reliability, particularly in high-motion environments.

With the widespread application of Voltage Source Converter (VSC) in the power system with high penetration of renewable resources, the problem of wideband oscillations caused by the interaction between the power converters and the power grid has drawn large attention. This paper presents a new methodology for simplifying the mathematical derivations of the impedance model of VSC. Using the new simplified model, the stability and the spectrum characteristic of the performance of the VSC can be clearly analyzed. The proposed second-order d-q impedance model of the grid connected VSC at presence of PLL, not only mathematically proves that the wideband oscillatory modes always occurs in conjugate pairs, but also deliver a clear vision of the physical essence of the wideband oscillations. The classic modal analysis is executed in the paper to demonstrate the stability and frequency spectral characteristics of the wideband oscillations in the VSC integrated system. The impact of control parameters of the VSC on the wideband oscillatory stability is thouroughly analyzed using the results of the modal analysis. The methodology can be considered a powerful tool for the control design of VSC in the modern power system.

Voltage Source Inverters (VSI) are the integral part of Electrical Vehicles (EV) to enhance the reliability of supply power to critical loads in vehicle to load (V2L) applications. Inherent properties of sliding mode control (SMC) makes it one of the best vailable options to achieve desired voltage quality under variable load conditions. Intrinsic characteristic of robustness associated with SMC is achieved generally at the cost of unwanted chattering along the sliding surface. To manage this compromise better, optimal selection of sliding surface coefficient is applied with proposed composite exponential reaching law (C-ERL). The novelty of proposed C-ERL is associated with the intelligent mix of exponential, power and difference functions blended with rotating sliding surface selection (RSS) technique for three phase two level VSI. Moreover, proposed reaching law along with power rate exponential reaching law(PRERL), enhanced exponential reaching law(EERL) and repeatitive reaching law(RRL) are implemented on two level three phase VSI under variable load condtions. Comparative analysis of which strongly advocates the authenticity and effectiveness of proposed reaching law in achieving well regulated output voltage, with high level of robustness, reduced chattering and low %THD.

Seaports are well known as the medium that has evolved into the central link between sea and land for complex marine activities. The growth in maritime logistics especially necessitates a large volume of energy supply to maintain the operation of sea trade, resulting in an imbalance between the generation and demand sides. Future projections for three major concerns show an increase in load demand, cost of operation, and environmental issues. In order to overcome these problems, integrating microgrids as an innovative technology in the seaport power system appears to be a vital strategy. It is believed that microgrids enhance the seaport operation by providing sustainable, environmentally friendly, and cost-effective energy. Despite the fact that microgrids are well established and widely used in a variety of operations on land, their incorporation into the seaport is still limited. The involvement of a variety of heavy loads such as all-electric ships, cranes, cold ironing, and buildings infrastructure makes it a complicated arrangement task in several aspects, which necessitate further research and leave space for improvement. In this paper, an overview of the seaport microgrids in terms of their concepts, requirements, and operation management is presented. It provides the perspectives of integrating the microgrid concept into a seaport from both shore side and seaside as a smart initiative for the green ports vision. Future research directions are discussed towards the development of more efficient marine power system.

Tree resin, which in addition to its widespread use in industry is also a macroergic component which has not yet been used for energy purposes. The main goal of this work is to determine the energy content of the resin of spruce, pine and larch and wood components – pulp and turpentine. The combustion heats of resin (MJ/kg) from each timber was determined calorimetrically. The energy values of tree resin (&gt;38.0 MJ.kg-1) were 2.2 and 2.4 times higher than that of bleached and unbleached cellulose, the highest value was recorded for the turpentine (&gt;39.0 MJ.kg-1). The best way of resin tapping is the America method, providing 5 kg resin ha-1 yr-1. The resin quantity tapped was raised at least 3 times applying stimulant, its production cost compared to other feedstocks was the cheapest. The tree resin can be applied as a good means to mitigate global warming and consequently dampen climate change. One tonne of tree resin burned instead of coal spares the atmosphere by 5.0 Mt CO2 since it is environmentally neutral. As resin heating values approach to the lower end of ones of liquid hydrocarbon fuels, greater efforts are needed to examine the most efficient energy use of resin.

Learning disorders (LD) are diagnosed in children impaired in the academic skills of reading, writing and/or mathematics. Children with LD usually show a slower resting-state electroencephalogram (EEG), with EEG patterns corresponding to a neurodevelopmental lag. LD-children also show a consistent cognitive impairment in working memory (WM), including an abnormal task-related EEG with an overall slower EEG activity of more delta and theta power, and less gamma activity in posterior sites; task-related EEG patterns considered indices of an inefficient neural resource management. Neurofeedback (NFB) treatments aimed at normalizing the resting-state EEG of LD-children have shown improvements in cognitive-behavioral indices and diminished EEG abnormalities. Given the typical findings of a WM impairment in LD-children; we aimed to explore the effects of a NFB treatment in the WM of children with LD, by analyzing the WM-related EEG power-spectrum. We recruited 18 children with LD (8-10 years old). They performed a Sternberg-type WM-task synchronized with an EEG of 19 leads (10-20 system) twice in pre-post treatment conditions. They went through either 30 sessions of a NFB treatment (NFB-group, n= 10); or through 30 sessions of a placebo-sham treatment (Sham-group, n= 8). We analyzed the before-after treatment group differences for the behavioral performance and the WM-related power-spectrum. The NFB group showed faster response times in the WM-task post-treatment. They also showed an increased gamma power at posterior sites and a decreased beta power. We explain these findings in terms of NFB improving the maintenance of memory representations coupled with a reduction of anxiety.

Since the recent legalization of medical and recreational use of cannabis (Cannabis sativa L.) in many regions worldwide, there has been high demand for research to improve yield and quality. With the paucity of scientific literature on the topic, this study investigated the relationships between light intensity (LI) and photosynthesis, inflorescence yield, and inflorescence quality of cannabis grown in an indoor environment. After growing vegetatively for 2 weeks under a canopy-level photosynthetic photon flux density (PPFD) of ≈ 425 μmol·m-2·s-1 and an 18-h light/6-h dark photoperiod, plants were grown for 12 weeks in a 12-h light/12-h dark ‘flowering’ photoperiod under canopy-level PPFDs ranging from 120 to 1800 μmol·m-2·s-1 provided by light emitting diodes. Leaf light response curves varied both with localized (i.e., leaf-level) PPFD and temporally, throughout the flowering cycle. Therefore, it was concluded that the leaf light response is not a reliable predictor of whole- plant responses to LI, particularly crop yield. This may be especially evident given that dry inflorescence yield increased linearly with increasing canopy-level PPFD up to 1800 μmol·m-2·s-1, while leaf-level photosynthesis saturated well below 1800 μmol·m-2·s-1. The density of the apical inflorescence and harvest index also increased linearly with increasing LI, resulting in higher-quality marketable tissues and less superfluous tissue to dispose of. There were no LI treatment effects on cannabinoid potency, while there were minor LI treatment effects on terpene potency. Commercial cannabis growers can use these light response models to determine the optimum LI for their production environment to achieve the best economic return; balancing input costs with the commercial value of their cannabis products.

The study explored the contribution of ICT-based information sources to market participation among smallholder livestock farmers. Use of ICTs is considered paramount for providing smallholder farmers with required market information, in order to reduce market asymmetries. A Double Hurdle regression was utilized to analyze data collected from 150 smallholder livestock farmers in the study area. The results show that while use of ICT-based market information sources significantly influenced market participation, the effect of using ICT-based information sources on intensity of market participation was not significant. Other variables shown to influence both market participation and the intensity of market participation were age, additional income and membership of farmer cooperatives. This suggests the need to also consider other associated factors in the application of interventions which utilize ICT-based information sources in achieving planned market interventions.

Although sources of seston are much more complicated in lakes compared to marines, the influences of different source on the spatiotemporal variations in seston stoichiometry are still underexplored, especially in large eutrophic floodplain lakes. Here, we investigated the seston stoichiometry across a typical large eutrophic floodplain lake (Lake Taihu) over one year. In addition, we used the n-alkanes proxies for source estimation which are more robust than other elemental indicators (e.g. C: N ratios). Throughout the study, the average value of C: N: P ratio of 143: 19: 1 across Lake Taihu was higher than the classical Redfield ratio, but closed to the synthesized data from other lakes. Generally, seston C: N ratios varied the least across all environments, but C: P and N: P ratios varied widely and shown a significant seasonal pattern with lower ratios of N: P and C: P during senescence seasons and higher ratios in the growing seasons. This seasonal change was mainly associated with the shift from terrestrial-derived seston to algal-derived seston as, the significant lower ratios of terrestrial-derived seston from surrounding agricultural watershed. Spatially, the mean ratios of each site were similar, except relative high values of C: P and N: P ratios in the algal dominated area. Statistically, the predictive power of environmental variables was strongly improved by adding n-alkanes proxies. However, apart from sources indicators, particulate phosphorus (PP) contents also partly explained the spatiotemporal variations in stoichiometric ratios. Nevertheless, the mechanisms behind the dynamics of PP could be totally different and source-specific. This study highlights the priority of using n-alkanes proxies as tools to identify the source of seston which is essential to interpret the spatiotemporal variations in seston stoichiometric ratios among eutrophic floodplain lakes.

The quality of digital elevation models (DEMs) is inevitably affected by the limitations of the imaging modes and the generation methods. One effective way to solve this problem is to merge the available datasets through data fusion. In this paper, a fusion-based global DEM dataset (82°S-82°N) is introduced, which we refer to as GSDEM-30. This is a 30-m DEM mainly reconstructed from the unfilled SRTM1, AW3D30, and ASTER GDEM v2 datasets combining the multi-source and multi-scale fusion techniques. A comprehensive evaluation of the GSDEM-30 data, as well as the 30-m ASTER GDEM v2 and AW3D30 DEM, was presented. Global ICESat GLAS data and the local National Elevation Dataset (NED) were used as the reference for the vertical accuracy validation, while GlobeLand30 was introduced for the landscape analysis. Furthermore, we employed the maximum slope approach to detect the potential artefacts in the DEMs. The results show that the GDEM data are seriously affected by noise and artefacts. With the advantage of the multiple datasets and the refined post-processing, the GSDEM-30 are contaminated with fewer anomalies than both ASTER GDEM and AW3D30. The fusion techniques used can also be applied to the reconstruction of other fused DEM datasets.

A focal plane array (FPA) detector was used for hyperspectral imaging in the infrared (IR) spectral region using thermal and synchrotron light sources. FPA Fourier-transform IR (FTIR) imaging microspectroscopy will be able to monitor real time changes at specific absorption bands when combined with high brightness synchrotron source. In this study, several types of samples with unique structural motifs were selected and used for assessing the capability of the FPA-FTIR imaging technique. It was shown that the time required for polariscopy at IR wavelengths can be substantially reduced by the FPA-FTIR imaging approach. By using natural and laser fabricated polymers with sub-wavelength features, alignment of absorbing molecular dipoles was revealed as well as higher order patterns (laser fabricated structures). Micro-spectroscopy of absorber orientation reveals alignment patterns even when they are not spatially resolved.

In Hawaiʻi, the transition from customary subsistence flooded taro agroecosystems, which regulate stream discharge rate trapping sediment and nutrients, to a plantation-style economy (c. the 1840s) led to nearshore sediment deposition - smothering coral reefs and destroying adjacent coastal fisheries and customary fishpond mariculture. To mitigate sediment transport, Rhizophora mangle was introduced in estuaries across Hawai’i (c. 1902) further altering fishpond ecosystems. Here, we examine the impact of cultural restoration between 2012-2018 at Heʻeia Fishpond, a 600-800-year-old walled fishpond. Fishpond water quality was assessed by calculating water exchange rates, residence times, salinity distribution, and abundance of microbial indicators prior to and after restoration. We hypothesized that R. mangle removal and concomitant reconstruction of sluice gates would increase mixing and decrease bacterial indicator abundance in the fishpond. We find that Heʻeia Fishpond’s physical environment is primarily tidally driven; wind forcing and river flux are secondary drivers. Post-restoration, two gates in the northeastern region account for >80% of relative flux in the fishpond. Increase in exchange rates during spring and neap tide and shorter minimum water residence time corresponded with the reconstruction of a partially obstructed 56 m gap together with the installation of an additional sluice gate in the fishpond wall. Lower mean salinities post-restoration suggests increased freshwater influx due to R. mangle removal. Spatial distribution of microbial bio-indicator species inversely correlated with salinity. Average abundance of Enterococcus and Bacteroidales did not significantly change after restoration efforts, however, average abundance of a biomarker specific to birds nesting in the mangroves decreased significantly after restoration. This study demonstrates the positive impact of biocultural restoration regimes on water flushing and water quality parameters, encouraging the prospect of revitalizing this and other culturally and economically significant sites for sustainable aquaculture in the future.

In table tennis competitions the rule violation judgment with the greatest controversy is the height of the ball serve. This is because inaccuracy in the ball height judgment, which results in erroneous judgment, is unavoidable. Thus, we designed an automatic image judgment auxiliary system for table tennis ball height during service in this study. We used a high-speed camera to record the ball toss in the table tennis service. The designed algorithm architecture can automatically search for the ball and the position of the hand action under low light source conditions. The algorithm is mainly divided into hue-saturation-value color space processing and morphology processing using Hough transform to search for the circular ball. Experiment result shows that color segmentation can successfully and accurately determine the ball position under low light conditions. The morphology method can find the position of the hand and help determine the moment when the ball leaves the hand during the service ball toss. Finally, the actual size of the target is used to estimate the actual distance unit represented by the image pixel.

The air is not the same as thousands and hundreds of years ago. In the air, suspended particles originate from natural phenomena like dust storms or volcanic activities, as well as anthropogenic pollutants such as fuel engine exhaust and everyday activities at home. The total particles in the air can be classified by sizes, such as PM10, PM2.5 or ultrafine particles. However, there are many other important factors in addition to the particle size, influencing the particle behavior and affecting our health. The surface area, chemical and biological composition, aspect ratio, and the charge are all factors characteristic of particles. OoC microfluidic chips are very useful for the pollutant toxicity measurements on various body tissues. A better understanding of pollutants will help to trace these to the potential sources. The data from the on-the-ground and satellite monitoring can be integrated into models, helping to predict and prevent pollution exposure.

The research field of energy system analysis is dealing with increasingly complex energy systems and their respective challenges. Moreover, the requirement for open science has become a focal point of public interest. Both drivers have triggered the development of a broad range of (open) energy models and frameworks in recent years. However, there are hardly any approaches on how to evaluate these tools in terms of their capabilities to tackle energy system modelling challenges. This paper describes a first step towards a flexible evaluation of software to model energy systems. We propose a qualitative approach as an useful supplementary to existing model fact sheets and transparency checklists. We demonstrate the applicability by evaluating the newly developed “Open Energy Modelling Framework” with respect to existing challenges in energy system modelling. The case study results highlight that challenges related to complexity and scientific standards can be tackled to a large extent while the challenges of model utilization and interdisciplinary modelling are only tackled partially. However, the challenge of uncertainty remains for the most part unaddressed at present. Advantages of the evaluation approach lie in its simplicity, flexibility and transferability to other tools. Disadvantages mostly stem from its qualitative nature. Our analysis reveals that some challenges in the field of energy system modelling cannot be addressed by a software as they are on meta level like model result communication and interdisciplinary modelling.

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

Keywords: renal replacement therapy. Point-of-Care Ultrasound; intensive care; acute kidney injury; nephrologist.Point of care ultrasonography (POCUS) is gaining heightened significance in critical care settings as it allows for quick decision making at the bedside. While computerized to-mography is still considered the standard imaging modality for many diseases, the risks and delays associated with transferring a critically ill patient out of the Intensive Care Unit (ICU) have prompted physicians to explore alternative tools. Ultrasound guidance has increased safety of invasive procedures in the ICU, such as the placement of vascular catheters and drainage of collections. Ultrasonography is now seen as an extension of the clinical examination, providing quick answers for rapidly deteriorating patients in the ICU. The field of nephrology is increasingly acknowledging the value of diagnostic Point-of-Care Ultrasound (POCUS). By employing multi-organ POCUS, nephrologists can address specific queries arising during the diagnosis and treatment of patients with acute kidney injury. This approach aids in ruling out hydronephrosis and offering immediate information on hemodynamics, thereby consolidating patient data and facilitating the development of personalized treatment strategies.

Femtoscopy is a unique tool to investigate the space-time geometry of the matter created in ultra-relativistic collisions. If the probability density distribution of hadron emission is parametrized, then the dependence of its parameters on particle momentum, collision energy, and collision geometry can be given. In recent years, several measurements came to light that indicated the adequacy of assuming a Lévy-stable shape for the mentioned distribution. In parallel, several new phenomenological developments appeared, aiding the interpretation of the experimental results, or providing tools for the measurements. In this paper we review and discuss some of these advances, phenomenological and experimental.

At present, failure definition and damage characteristic curve (DCC) analysis included in the framework to assess bitumen fatigue cracking performance have an inconsistency in ranking bitumen fatigue behaviour. This study utilized two types of self-healing polymers (STP and IPA1w) to modify the neat asphalt (NA), and research four different types of bitumens: NA, STP-modified bitumen, IPA1w-modified bitumen, and styrene-butadiene-styrene modified bitumen (SBSB), to evaluate the above-mentioned framework. All bitumens were subjected to short-term and long-term aging and tested utilizing the Linear amplitude sweep (LAS) test and simplified viscoelastic-continuum-damage (S-VECD) model. The results showed that the SBSB exhibited the highest numbers of loading cycles (in long-term aging analysis) to reach failure points at 25°C, 28°C, and 31°C which were 2290, 2340, and 2510, respectively. However, this bitumen failed to exhibit the best performance in terms of DCC assessment under the same conditions, confirming the above-mentioned inconsistency. Besides, the current failure criterion could not accurately predict bitumen fatigue behaviour under certain test conditions because two R2 values were below 0.1. As a result, this study proposed a new failure definition and failure criterion to overcome these issues. The proposed failure definition agreed with the DCC analysis to rank bitumen fatigue performance, and the proposed failure criterion showed R2 values higher than 0.9. The new framework presented the modified bitumen containing 0.5% of STP as the asphalt binder with the best fatigue cracking performance, according to the selected test conditions.

In this study, we focus on an abstract form of summation equations, which can be regarded as a particular class of nonlinear difference equations. We investigate sufficient conditions for the existence of discrete almost automorphic solutions by appealing to the fixed point theory and establish a linkage between the existence of discrete almost automorphic solutions and the existence of bounded solutions for the nonlinear difference equations in the spotlight. Consequentially, we propose a discrete counterpart of the Bohr-Neugebauer theorem for the qualitative theory of difference equations.

Based on the teaching material of "Robotics" course, this paper studied the automatic knowledge graph construction, including knowledge points extraction and knowledge point relation extraction. We proposed a new method of extracting the first-level, second-level, and third-level knowledge points as well as their prerequisite relations of knowledge points in the textbook. For the problem of insufficient knowledge of the pre-trained language model in the specific field, methods such as incremental pre-training and optimization of cost functions are employed to integrate subject knowledge into the pre-trained language model, thus improving its effectiveness. To overcome the problem that the traditional method of relationship extraction can not be applied directly to the extraction of teaching materials, a new scheme for knowledge point relationship extraction based on keyword relationship is proposed. The experimental data from textbooks shows that the F1 score of knowledge point extraction reaches 93%, considerably improved compared to the traditional model. Consequently, the knowledge point entity extraction and relationship extraction methods based on the pre-trained model can effectively extract structured information and facilitate the automatic construction of knowledge graphs.

Unmanned aerial vehicles (UAV) have emerged as a solution to day to day survey tasks, allowing users to visualize phenomena in real-time. This paper explores the capabilities of UAV or drones in the collection of accurate, geo-tagged data quickly, including photogrammetry software processes to deliver standardized data output. In order to explore the capabilities of UAV, Gatu Township in Centenary, Muzabani District of Zimbabwe was chosen from the national mapping topographic series. This study demonstrates the efficiency of data collection using drones, generate 2D orthomosaics in real time, so that analysts can easily visualize land cover and identify any changes, map and model large areas to produce data for 2D and 3D models. The recent development of innovative optical image processing has further lowered the costs high resolution topographic surveys.

Most petrochemical plants still maintain a Proportional-Integral-Differential controller(PID) system, which is a feedback control system. However, gradually, the PID system is being extended and introduced to the Advanced Process Controller (APC) system, which is an integrated control system of feedforward and feedback that predicts external influences in advance. In the process of conducting on-site plant tests and calculating APC model parameter for the application of APC systems, a problem arises that Model Parameter are implemented differently depending on the proficiency of APC engineers. To minimize this problem, a technique for estimating APC model parameter without a plant test is required. In order to estimate the APC model parameter, it is necessary to train on dynamic interval data. In this paper, we use statistical techniques such as PELT, Linear Kernel, and Radial Basis Function Kernel of Change Point Detection (CPD) to extract dynamic data with minimum Mean Absolute Error (MAE) from time series data of a real petrochemical plant. Then, the hyper parameter is fixed and the APC model parameter is estimated by learning the dynamic section data. By applying the estimated APC model parameter to the APC Model Tool and measuring the fitting rate, it was confirmed that it is possible to estimate the APC model parameter with excellent control performance without plant test.

The accelerated pace with which new diagnostic possibilities are produced and the budget re-strictions of the healthcare sector require that the decision-making process of acquiring new technologies becomes systematic in nature. There are some methodologies such as the Health Technology Assessment (HTA) that encompasses technological domains, clinical effectiveness, patient safety, organizational and financial aspects, among others. However, these methods do not contemplate the learning curve (LC) which is a differential factor in operator-dependent technologies. An assessment model was conceived based on the assessment domains of the AdHopHTA project with the addition of LC. The model was validated and calibrated through System Dynamics (SD) and using as case study the assessment of Point-of-care Ultrasound (POCUS) equipment in dengue screening. The model helped identify the influence of the LC and patient demand on the income and costs for the healthcare system regarding dengue screening as well as the cost-benefit indicator. The control charts LC-CUSUM and CUSUM are graphic tools to intuitively assess the learning curve which can be used for real-time monitoring once students reach a certain skill level.

We study the Kelvinons: monopole ring solutions to the Euler equations, regularized as the Burgers vortex in the viscous core. There is finite anomalous dissipation in the inviscid limit. However, in the anomalous Hamiltonian, some terms are growing as logarithms of Reynolds number; these terms come from the core of the Burgers vortex. In our theory, the turbulent multifractal phenomenon is similar to asymptotic freedom in QCD, with these logarithmic terms summed up by an RG equation. The small effective coupling does not imply small velocity; on the contrary, velocity is large compared to its fluctuations, which opens the way for a quantitative theory. In the leading order in the perturbation theory in this effective coupling constant, we compute running multifractal dimensions for high moments of velocity circulation, in good agreement with the data for quantum Turbulence and available data for classical Turbulence. The logarithmic dependence of fractal dimensions on the loop size comes from the running coupling in anomalous dimensions. This slow logarithmic drift of fractal dimensions would be barely observable at Reynolds numbers achievable at modern DNS.

Quantum computing has attracted significant interest in the optimization community because it potentially can solve classes of optimization problems faster than conventional supercomputers. Several researchers proposed quantum computing methods, especially Quantum Interior Point Methods (QIPMs), to solve convex optimization problems, such as Linear Optimization, Semidefinite Optimization, and Second-order Cone Optimization problems. Most of them have applied a Quantum Linear System Algorithm at each iteration to compute a Newton step. However, using quantum linear solvers in QIPMs comes with many challenges, such as having ill-conditioned systems and the considerable error of quantum solvers. This paper investigates how one can efficiently use quantum linear solvers in QIPMs. Accordingly, an Inexact Infeasible Quantum Interior Point Method is developed to solve linear optimization problems. We also discuss how we can get an exact solution by Iterative Refinement without excessive time of quantum solvers. Finally, computational results with a QISKIT implementation of our QIPM using quantum simulators are analyzed.

Commonwealth Partnerships for Antimicrobial Stewardship (AMS) uses a health partnership model to establish AMS in Commonwealth countries. The University Hospital of Kwame Nkrumah University of Science and Technology in partnership with Ulster University, in Northern Ireland undertook an AMS project from November 2021 to May 2022. We report on the implementation and its effect on antibiotic use and infections management at the University Hospital. The Global-Point Prevalence Survey (PPS) protocol was used to assess antibiotics use at the hospital at the beginning, midpoint and end of the project. Feedback on each PPS was given to staff to inform behaviour change and improve antibiotic prescribing. Antibiotic use reduced from 65% at baseline to 59.7% at the end of the project. The rate of health-associated infections also reduced from 17.5% at baseline to 6.5%. In addition, the use of antibiotics belonging to the WHO Access group at the hospital was 40% initially but increased to 50% at the project endpoint. Culture and antibiotic susceptibility requests increased from the beginning of the project from 111 total requests to 330 requests over 7 months. The AMS model implemented improved antibiotic use as well as requests for culture and susceptibility test which must be sustained.