This research was specifically aimed at assessing the influence of sulfur in triple-super phosphate (TSP) on wheat yield. From the results, wheat showed response to sulfur (S) from gypsum (in 67%); and nitrogen (N) from urea in about 100% (of 24 sites). Based on this N was found to be the most limiting element to wheat production followed by sulfur, and then by phosphorus. TSP is tested to contain agronomically up to 2-6% by weight of S. However, wheat didn’t show response to S impurity supplied in the form of TSP. Though, not statistically significant, it is observed that there have always been yield increments by certain percent due to S from TSP in 8 out of 10 target sites, which is depicted in the increasing trends of yield response curves. From this it is learnt that, the benefits of the accidental/incidental application of such high analysis fertilizers can be many-folds in the quality attributes of wheat, if the soils of such investigation at the same time would contain significant amount of organic matter (OM). Indeed, such analysis would be vital in varietal specific nutrient requirement studies in precision-farming and/or in categorizing soils into fertility gradients and fertilizer recommendation domains.

Many studies have found that future predicted CO2 levels (< 800 ppm) can increase plant mass but dilute N content in leaves, impacting antiherbivore compounds. Nitrogen-fixing plants may balance leaf C:N ratio under elevated CO2, counteracting this dilution effect. The aim of this study was to look at how nitrogen-fixing plants grow and respond to herbivore damage at different CO2 levels. Alnus incana ssp. rugosa was grown at 400, 800, or 1600 ppm CO2 in soil collected from the field, inoculated with Frankia and exposed to herbivores (Orgyia leucostigma). Elevated CO2 increased nodulated plant biomass and stimulated the nitrogen fixation rate in the early growth stage. However, nitrogen-fixing plants were not able to balance the C:N ratio under elevated CO2 after grown 19 weeks. When plant were grown at 400 and 1600 ppm CO2, herbivores preferred to feed on leaves of nodulated plants. At 800 ppm CO2, nodulated plants accumulated more total phenolic compounds in response to herbivore damage than plants in the non-Frankia and non-herbivore treatments. Our results suggest that plant leaf defence, not leaf nutritional content, is the dominant driver of herbivory and nitrogen fixing plants have limited ability to balance C:N ratios at elevated CO2 in natural soil.

Excessive nutrient discharge to tropical island coastlines drives eutrophication and algal blooms with significant implications for reef ecosystem condition and provision of ecosystem services. Management actions to address nutrient pollution in coastal ecosystems include setting water quality standards for discharging surface waters. However, these standards do not account for the effects of groundwater discharge, variability in flow, or dilution, all of which may influence assessment of true nutrient impacts on nearshore reef habitats. We developed a method to estimate dissolved inorganic nitrogen (DIN) loads to coastal zones by integrating commonly available datasets within a geospatial modeling framework for Tutuila, American Samoa. The DIN loading model integrated an open-source water budget model, water sampling results, and publically available streamflow data to predict watershed-scale DIN loading to the island’s entire coastline. When compared to surface water pathways, submarine groundwater discharge (SGD) was determined to be the most important coastal delivery mechanism of terrigenous DIN, which supports findings from other tropical islands. Onsite wastewater disposal systems were also found to be the primary anthropogenic sources DIN to coastal waters. Our island-wide DIN loading model provides a simple and robust metric to define spatially-explicit sources and delivery mechanisms of nutrient pollution to nearshore reef habitats. Understanding the sources and primary transport modes of inorganic nitrogen to nearshore reef ecosystems can have significant implications for place-based management interventions aimed at increasing the adaptive capacity of unique island ecosystems to environmental variation and disturbances.

Impact of Nitrogen Foamed Stimulation Fluids Stabilized by Nanoadditives on Reservoir Rocks of Hydrocarbon Deposits

Dipteryx spp. is an important species in reforestation in the Amazon. The objective of this study is to characterize and compare the relationships between dendrometric variables in Dipteryx spp. stands in the Western Amazon by fitting linear regression equations for total height and crown diameter. Six forest stands were evaluated in three municipalities. Dendrometric variables collected included diameter at 1.3 m height (dbh), total height (ht) and crown diameter (dc). Simple and multiple linear regression equations were fitted to characterize the relationships between ht and dc. The total aboveground biomass of Dipteryx spp. trees and the carbon stock of the stands were estimated. The general equations showed higher R² values, exceeding 0.7. The general equations for estimating ht and dc were significant for all coefficients. The trees averaged 22 t/ha of aboveground biomass in the stands. There was a variation in carbon sequestration potential among stands, ranging from 5.12 to 88.91 t CO2.ha-1. Single-input equations using dbh as an independent variable are recommended for estimating dc and ht for individual Dipteryx spp. stands. Stands in the Western Amazon play a significant role in carbon sequestration and accumulation. Trees can sequester an average of 4.8 tons of CO2 per year.

Implementing net-zero building design is a crucial step towards decarbonizing the built environment during the entire lifecycle of a building, encompassing both embodied and operational carbon. This paper presents a novel computational approach to design Life Cycle Zero-Carbon Building (LC-ZCB), utilizing parametric integrated modeling through the versatile Grasshopper platform and its plug-ins. The Department of Energy’s prototype residential building at New York Institute of Technology, optimized to fulfill the LC-ZCB target, serves as the base building for this comprehensive study. Four main influencing design parameters, namely geometry, construction technology, thermal resistance of the envelope, and on-site renewable energy production, are defined and three-hundred design combinations are evaluated through the assessment of the operational carbon (OC) and embodied carbon (EC). By incorporating bio-based materials in the design options, the influence of biogenic carbon on the whole carbon footprint of the building case study is addressed by utilizing the GWPbio dynamic method, which assumes 100-year time horizon and incorporates dynamic characterization factors based on time of pulse emissions and two variables: rotation of the biomass and storage period of carbon in products. Finally, to account for potential climate changes, future climate data and 2099 weather conditions are considered during the scenarios assessment. The results demonstrate the potential for achieving LC-ZCB when fast growing biobased materials are largely used as construction materials, fostering a more environmentally responsible future for the construction industry.

The escalating concerns over climate change have propelled industries worldwide to seek innovative strategies for mitigating greenhouse gas emissions. Within the energy sector, Carbon Capture and Storage (CCS) technology emerges as a promising solution to curtail emissions and foster sustainable development aims for net zero approach. The research delves into the role of government support in expediting CCS adoption for the maximum potential of 9.79 MtCO2 storage from six major refinery plants. The refineries mentioned above are anticipated to necessitate an initial capital investment of approximately 18,307 million THB. This research focuses on potential business model proposals appropriate for a country's context, specifically applying CCS technology to Thai oil refining sector. To achieve the realization of CCS within the context of this study, a combination of three essential measures will be required: tax incentives, carbon credits, and grants. This process will commence with the implementation of tax incentives, followed by an increase in the carbon price within the country. Finally, the establishment of a dedicated fund, funded through deductions from oil excise tax revenue, will play a pivotal role in facilitating the necessary financial support for the emergence of CCS.

Logistics industry has been found to be among the key sources of carbon emission. In Vietnam logistics industry, there is a considerable difference between the number of foreign and Vietnamese firms as well as the proportion of markets that they are taking. This study is to research the low-carbon emission measures conducted by domestic and foreign invested logistics service providers (LSPs) and compare the results of the two groups. Both qualitative and quantitative approaches are applied. Literatures in relevant fields are reviewed and expert opinions are taken for structuring a questionnaire which was later distributed to 279 LSPs, with 166 returned and 159 being valid for data calculation. The results imply that there are differences in extension of applications of low-carbon practices between foreign and domestic firms. Except for transport mode switch and energy-saving lighting, the other practices witness that adoption levels of foreign LSPs are higher than their counterparts, which is possibly thanks to their global operation, more comfortable capital resources and awareness level of green initiative necessity. In conclusion, a comparison between the application conducted by foreign-invested firms and domestic ones, which has not been investigated before, was made.

Through this study, we established equations for estimating the standing tree carbon stock, based on 24 tree species in multiple size classes in a case study at the Ngao Demonstration Forest (NDF) in northern Thailand. Four hundred thirty-nine wood samples from trees in mixed deciduous forest (MDF), dry dipterocarp forest (DDF), and dry evergreen forest (DEF), were collected using non-destructive methods to estimate above-ground carbon equations through statistical regression. The equations were established based on four criteria: 1) the coefficient of determination (R2), 2) Standard error of estimate (SE), 3) F-value, and 4) Significant value (p-value, α ≤ 0.05). The above-ground carbon stock (C) equations for standing trees in the MDF was C = 0.0199DBH2.1887H0.5825, for DDF was C = 0.0145DBH2.1435 H0.748, for DEF was C = 0.0167DBH2.1423H0.7070, and the general equation for all species/wood density groups was C = 0.017543DBH2.1625H0.6614, where DBH is tree diameter at breast height and H is tree total height. The above-ground carbon stock in the DDF, MDF, and DEF was 142, 53.02, and, 12 tons/ha, respectively, and the estimated above-ground carbon stock in the Mae Huad sector at the NDF was 61 tons/ha.

Land’s basic metric is soil organic carbon (SOC) yet global estimates range 1,417–15,000 Gt C. Erosion of ancient topsoil and loss of soil taxa are most urgent of all context-triage concerns, and most ignored. Re-evaluation of topographical terrain on a non-flat Earth increases most soil dynamic inventories. Carbon credits of our neglected and disappearing SOC stocks are enumerated for mineral soils (~4,100 Gt C plus ca. 20–30% glomalin), Permafrost (>4,200 Gt C), peat (1,123 Gt C), plant roots (916 Gt C), litter (600 Gt C), microbes (200 Gt C), fungi (30 Gt C), biocrust (10–20 Gt C), earthworms (2.3–3.6 Gt C), termites (0.15 Gt C), nematodes (0.06 Gt C), ants (0.024 Gt C), and soil viruses (0.02–4.0 Gt C). Net contribution to atmospheric CO₂ is more from biotic topsoil loss (>10 Gt C/yr) than fossil fuels (<10 Gt C/yr). Although higher CO₂ results in a terrestrial greening effect with Net Primary Productivity (NPP) now ~220 Gt C/yr (cf. ~20 Gt C/yr Ocean NPP), this is arguably offset by topsoil erosion, desert expansion, plus fire at net ~16–20 Gt C/yr lost due, in part, to extravagant meat-eating with unsupportable, humus-depleting farm management. In particular, excess synthetic Nitrogen acidifies topsoil and destroys the natural SOC biota. Review shows critical topsoil loss up to 20,000 tonnes per second and, when soil microbes/invertebrates are properly considered, extinctions as high as 23 taxa per second. Sustainable Development Goals (SDGs) fail without solid soil foundation. Rather, heritage farm-data points to resolution in organic husbandry. Remedy via natural vermi-compost, 100% organic farming and practical Permaculture is under a simple premise that the Problem (i.e., SOC loss) is the Solution (viz., SOC restoration).

The Equator Principle is the goal of promoting the harmonious development of my country's economy and society. It promotes the green transformation and upgrading of the industrial structure by strictly controlling the flow of commercial bank funds, so as to achieve the goal of environmental protection and the coordinated development of the national economy. This paper uses factor analysis to reduce the dimensions of 10 financial indicators and non-financial indicators that measure the operating performance and development potential of joint-stock commercial banks, and then compares the comprehensive operating performance, liquidity, and safety of Industrial Bank and comparable banks. And the level of profitability, analyze the difference in comprehensive operating performance of joint-stock commercial banks joining the Equator Principles compared with commercial banks that have not joined the Equator Principles. The results of the study found that joining the Equator Principles of joint-stock commercial banks can improve comprehensive operating performance in the short term. In the long run, the development trend of Industrial Bank will be similar to that of comparable banks in the same category. Joining the Equator Principles of Industrial Bank can improve its liquidity and profitability, but it will not in the long run. Conducive to the improvement of the asset quality of joint-stock commercial banks. In this regard, the government, enterprises and financial institutions should work together to help commercial banks achieve an effective balance between operating performance and social responsibility, so as to achieve the goals of "carbon peak" and "carbon neutral".

With increasing interest in understanding contribution of secondary organic aerosol (SOA) to particulate air pollution in urban areas, an exploratory study was carried out to determine levels of carbonaceous aerosols and polycyclic aromatic hydrocarbons (PAHs) in the City of Kuala Lumpur, Malaysia. PM2.5 samples were collected using a high-volume sampler for 24 h in several areas in Kuala Lumpur during the north-easterly monsoon from January to March 2019. Samples were analysed for water soluble organic carbon (WSOC), organic carbon (OC), elemental carbon (EC) and secondary organic carbon (SOC) in PM2.5 was estimated. Particle-bound PAHs were analysed using gas chromatography-flame ionization detector (GC-FID). Average concentrations of WSOC, OC and EC were 2.7 ± 2.2 (range of 0.63-9.1) µg/m3, 6.9 ± 4.9 (3.1-24.1) µg/m3 and 3.7 ± 1.6 (1.3-6.8) µg/m3, respectively, with estimated average SOC of 2.3 µg/m3, contributing 34% to total OC. The average of total PAHs was 1.8 ± 2.7 ng/m3. Source identification methods revealed natural gas and biomass burning, and urban traffic combustion as dominant sources of PAHs in Kuala Lumpur. To understand human health risk posed by PAHs, a deterministic screening health risk assessment was also conducted for several age groups including infant, toddler, children, adolescent and adult. The total concentration of BaPeq is 3.8 ng/m3, with the average of 0.29 (range of 0.001-1.6) ng/m3. Carcinogenic and non-carcinogenic risk of PAH species were well below the acceptable levels recommended by the USEPA. Future work is needed using long-term monitoring data to understand the origin of PAH contributing to SOA formation and to apply source-risk apportionment to know better the potential risk factors posed by the various sources in urban areas in Kuala Lumpur.

Soil organic carbon (SOC) mineralization is closely related to carbon source or sink of terrestrial ecosystem. Understanding soil organic carbon (SOC) mineralization under plum plantation is essential for improving our understanding of SOC responses to land-use change in karst rocky desertification ecosystem. In this study, 2-y, 5-y and 20-y plum plantations and adjacent woodland were sampled and a 90-day incubation experiment was conducted to investigate the effect of plum plantation with different years on SOC mineralization in subtropical China. Results showed that: (1) there was no significant difference in SOC content between different planting years, but there were significant differences in accumulative SOC mineralization (C_t) and potential SOC mineralization (C₀); (2) the dynamics of the SOC mineralization was a good fit to a first-order kinetic model. Both C₀ and C_t in calcareous soil of this study was several to ten folds lower than that in other soils, indicating that SOC in karst region has higher stability. (3) Correlation analysis revealed that both C_t and C₀ was significantly correlated with soil calcium (Ca) and C/N, indicating the important role of Ca and C/N in SOC mineralization in karst rocky desertification area.

Three rice paddy fields under farmers’ actual management conditions were investigated from May to April at Bibai (43°18′N, 141°44′E), in central Hokkaido, Japan to evaluate the carbon (C) sequestration and contribution of CO2, CH4 and N2O fluxes to a global warming potential (GWP). CH4 and N2O fluxes were measured by placing the chamber over the rice plants covering four hills and CO2 fluxes from rice plants root free space in paddy fields were taken as an indicator of soil microbial respiration (Rm) using the closed chamber method. Annual cumulative Rm ranged from 422 to 519 g C m-2 yr-1; which accounted for 54.7 to 55.5 % mainly during the rice growing season. Annual cumulative CH4 emission ranged from 75.5 to 116 g C m-2 yr-1 and this contribution occurred entirely during the rice growing period. Annual cumulative N2O emission ranged from 0.091 to 0.154 g N m-2 yr-1 and 73.5 to 81.3% of the positive annual N2O emission observed during the winter-fallow season. Soil C sequestration was estimated as the difference between net primary production (NPP) and C loss through Rm, CH4 emission and crop C harvest. The soil C sequestration ranged from -305 to -365 g C m- 2 yr-1, indicating that the C loss could not be compensated for by C input through NPP. Carbon loss was much higher (62 to 66%) in winter-fallow season than growing season. The annual net GWP from the investigated paddy fields ranged from 3823 to 5016 g CO2 equivalent m-2 yr-1. Annual GWPCH4 accounted for 71.9 to 86.1% of the annual net GWP predominantly from the rice growing period. These results indicate that CH4 dominated the rice paddy’s net GWP.

Low carbon cities are increasingly forming a distinct strand of sustainability literature. Models have been developed to measure the performance of low carbon cities. The purpose of this paper is to formulate a strategy-based model to evaluate current performance and predict future conditions of low carbon cities. It examines the dynamic interrelationships between key performance indicators (KPIs), induces changes to city plan targets and then instantly predicts the outcome of these changes. Designed generic and flexible, the proposed model shows how low carbon targets could be used to guide the transformation of low carbon cities under four strategies: (1) passive intervention, (2) problem solving, (3) trend modifying and (4) opportunity seeking. Further, the model has been applied to 17 cities and then tested on 5 cities: London, New York, Barcelona, Dubai and Istanbul. The paper concludes with policy implications to realign city plans and support low carbon innovation.

Air pollution has been a major environmental issue worldwide from the last few decades. It is a man-made issue that has a serious harmful impact on the environment and the health of humans. There are different sources of emission, but industrial processes and motor vehicles contribute to a chief part of air pollution. It has acute as well as chronic effects on the health of humans and affects different organs. It is thought the main environmental risk factor in the incidence and progression of several diseases such as lung cancer, asthma, Alzheimer's and Parkinson's diseases. Long-term exposure to air pollution has different toxicological impacts on humans such as respiratory and cardiovascular diseases, neuropsychiatric complications, eye irritation and skin diseases. As per the study by the World Health Organization (WHO), nitrogen oxides (NOx), carbon monoxide (CO), ozone (O₃), sulfur dioxide (SO₂), volatile organic compounds (VOCs) and heavy metals are the major air contaminants. These pollutants are different in their properties, composition and time of disintegration. The aim of this study is to review the different sources, types, impacts, challenges and mitigation of air pollution in detail.

This study investigates the influence of adding hydrogen as an additive to gasoline in a four-stroke engine, utilizing a comprehensive thermodynamic comparative analysis conducted with self-developed engine model. The research aims to assess the performance, emissions, and efficiency of the engine when using gasoline-hydrogen blends, and to provide insights into the potential benefits of this approach. First the engine performance and emissions under different hydrogen blending levels were examined. A range of different air-to-fuel ratios (rich to lean) and varying percentages of hydrogen were considered. This systematic variation allowed for a detailed evaluation of the influence of hydrogen content on combustion efficiency, power out-put, and emissions characteristics. The analysis results included key parameters such as indicated specific fuel consumption and mean effective pressure. Additionally, the study focused on range prediction of nitrogen oxides (NOx) emissions, which are a critical environmental concern asso-ciated with internal combustion engines. The analysis of pressure and temperature profiles throughout the engine cycle shed light on the combustion characteristics and efficiency im-provements associated with hydrogen addition. In terms of emissions, the study projected that all emissions were reduced except NOx, which is highly dependent on hydrogen percentage, and it might be reduced in some cases, but with higher temperatures and pressures associated with hydrogen addition in most cases there is actually NOx increase, especially at higher engine loads.

Keywords: Amorphous-precipitate, Nitride, Morphological stability, Diffusion, Internal stresses, Modelling, Simulation

Quantification of the trade-offs among greenhouse gas (GHG) emissions, yield and farmers’ incomes is essential for proposing economic and environment nitrogen (N) management strategies for optimizing agricultural production. A four-year (2017–2020) field experiment (including four treatments: control experiment (CK), suitable utilization of fertilization (SU), emission reduction treatment (ER), and high fertilization (HF)) was conducted on maize (Zea mays L.) in the North China Plain. The Life Cycle Assessment (LCA) method was used in this study to quantify the GHG emissions and farmers’ incomes during the whole maize production process. The total GHG emissions of CK, SU, ER and HF treatments in the process of maize production are 10,755.2, 12,908.7, 11,950.1, and 14,274.5 kg CO2-eq ha−1 respectively, of which the direct emissions account for 84.8%, 76.8%, 74.9%, and 71.0%, respectively. Adding inhibitor significantly reduced direct GHG emissions, and the N2O and CO2 emissions from the maize fields in the ER treatment decreased by 30.0% and 7.9% compared to those in the SU treatment. Insignificant differences in yield were found between the SU and ER treatments, indicating that adding fertilizer inhibitors did not affect farmers’ incomes while reducing GHG emissions. The yield for SU, ER and HF treatments all significantly increased by 12.9%–24.0%, 10.0%–20.7% and 2.1%–17.4% compared to CK, respectively. In comparison with CK, both SU and ER significantly promoted agricultural net profit (ANP) by 16.6% and 12.2% with the mean ANP values of 3,101.0 USD ha-1 and 2,980.0 USD ha-1, respectively. Due to the high agricultural inputs, the ANP values in the HF treatment was 11.2%, 16.6% and 12.4% lower than those in the SU treatment in 2018–2020. In conclusion, the combination of N fertilizer and inhibitors was proved to be an environmentally friendly, high-profit and low-emissions production technology while sustaining or even increasing maize yields in the North China Plain, which was conducive to achieving agricultural sustainability.

Cattle slurry is an important nitrogen source for maize on dairy farms. Slurry injection is an effective measure to reduce ammonia emissions after field application, but with higher risk of nitrous oxide emission than surface application. This study compared soil mineral nitrogen dynamics and nitrous oxide emissions with two ways of application. First, traditional injection at 25 cm spacing between rows followed by ploughing (called “non-placed slurry”), and second, injection using a new so-called goosefoot slurry injector that placed the slurry in ploughed soil as a c. 30 cm broad band at 10 cm depth below maize crop rows with 75 cm spacing (named “placed slurry”). Furthermore, the effect of treating slurry with the nitrification inhibitor 3,4-dimethylpyrazole phosphate (DMPP) in Vizura® was tested with both application methods. The field experiment was conducted on a sandy loam soil in a temperate climate. Both nitrous oxide emissions, and the dynamics of soil mineral nitrogen, were monitored for eight weeks after slurry application and seeding of maize using static chambers. The level of nitrous oxide emissions was higher with non-placed compared to placed slurry, mainly due to higher emissions during the first four weeks. That might be due to higher rates of nitrification rate and in turn stimulation of denitrification process. In both placed and non-placed slurry treatments, Vizura® caused higher soil ammonium concentrations and lower nitrate concentrations, particularly from 3 to 8 weeks after slurry application. The final level of soil nitrate was similar with and without the nitrification inhibitor, but higher with placed compared to non-placed slurry. Adding Vizura® to non-placed slurry reduced nitrous oxide emissions by 70 % when compared to placed slurry. Surprisingly, there was a non-significant trend towards higher cumulative emissions from placed slurry with the nitrification inhibitor compared to untreated slurry, which were due to higher emissions in the last part of the monitoring period (5-7 weeks after slurry application). Possibly degradation of the nitrification inhibitor, and nitrification activity inside the slurry band as the soil dried, promoted nitrous oxide emissions by this time. In summary, placement of untreated slurry in a broad band under maize seeds reduced nitrous oxide emissions compared to non-placed slurry with more soil contact. A comparable reduction was achieved by adding a nitrification inhibitor to non-placed slurry. The pattern of nitrous oxide emissions from placed slurry treated with the inhibitor was complex and requires more investigation.

In rice, symbiotic N fixation via nodule bacteroids does not take place naturally. Although N fixation by endophytic and associative diazotrophs has been reported in rice, main organs and seasonal regulation for the N fixation have not been elucidated. In this study, therefore, seasonal changes of nitrogenase (acetylene reduction) activity and carbohydrate contents in culm internode (IN), basal nodes (BN), and crown root (CR) were investigated in manure compost (MC)- and chemical fertilizer-applied rice. Nitrogenase activity increased after rooting, and reached the highest activity in BN of MC-applied rice at panicle initiation. In BN of MC-applied rice, the sucrose content was low whereas the higher glucose content was detected at panicle initiation. Although bacterial and diazotrophic bacterial populations were most abundant in CR, the nitrogenase activity seemed to be restricted by its trace sucrose and glucose contents. In addition, alpha-Proteobacteria and Clostridia phyla were abundant in BN-specific bacterial microbiota at panicle initiation. These results suggest that the increased N fixation in BN at panicle initiation might be sustained both by the non-structural carbohydrate supply from photosynthetic apparatus and BN-specific bacterial microbiota including diazotrophs.

ST-segment elevation myocardial infarction (STEMI), a major cause of mortality worldwide, has been shown through epidemiological studies to have a relationship with short-term exposure to air pollutants; however, the association between air pollutants and the outcome of STEMI has not been well studied. The aim of this study was to estimate the impact of air pollutants on the outcomes of STEMI. Data on particulate matter <2.5 μm (PM2.5), <10 μm (PM10), nitrogen dioxide (NO2), and ozone (O3) at each of the 11 air monitoring stations in Kaohsiung City were collected between January 1, 2012, and December 31, 2017. Medical records of non-trauma patients aged > 20 years who had visited the ED with a principal diagnosis of STEMI were extracted. The primary outcome measure was in-hospital mortality. After adjusting for potential confounders and meteorological variables, we found that an increase in the interquartile range (IQR) in NO2 was associated with an elevated risk of in-hospital mortality in patients with STEMI. Moreover, during the warm season, an IQR increase in NO2 corresponded to a higher risk of in-hospital mortality in patients with STEMI on lag 3 (OR=3.266; 95% CI:1.203–8.864, p=0.02). Conversely, an IQR increase in PM10 was associated with an increased risk of in-hospital mortality in patients with STEMI on lag 3 (OR=2.792; 95%CI:1.115–6.993, p=0.028) during the cold season. Our study suggests that exposure to NO2 (during warm season) and PM10 (during cold season) may contribute to a higher risk of poor prognosis in patients with STEMI.

To meet the growing interest in the development of innovative biological nutrient removal (BNR) alternatives for energy neutrality, resource recovery, and decarbonization, the adsorption/bio-oxidation (A/B) process has been widely studied for carbon capture and shortcut nitrogen (N) removal, while limited research has focused on incorporating enhanced biological phosphorus (P) removal (EBPR), mainly due to the differential carbon usage characteristics of functionally relevant microorganisms. Here, a full-scale pilot testing with an integrated system combining A-stage high-rate activated sludge (HRAS) with B-stage partial (de)nitrification/anammox and side-stream EBPR (HRAS-P(D)N/A-S2EBPR) was conducted treating real municipal wastewater. The results demonstrated that, despite the low influent carbon load, the B-stage P(D)N-S2EBPR system achieved effective and stable P removal performance, especially when the volatile fatty acid (VFA) load from A-stage was elevated. Sludge fermentation in both A-stage and B-stage promoted carbon redistribution and likely provided more competitive advantages for ammonium-oxidizing bacteria and polyphosphate accumulating organisms, leading to carbon-efficient shortcut N removal mainly through partial nitrification pathway and influent carbon-independent EBPR simultaneously. Exposure to high VFA levels was considered a potential selection factor for the suppression of nitrite-oxidizing bacteria in the system. The involvement of internal carbon-accumulating organisms would potentially play an important role in endogenous denitrification. This study provided new insights into the effects of incorporating side-stream EBPR into the A/B process on microbial ecology, metabolic activities, and system performance.

During the COVID-19 lockdown in Wuhan, transportation, industrial production and other human activities declined significantly, as did the NO2 concentration. In order to assess the relative contributions of different factors to reductions of air pollutants, sensitivity experiments were implemented by random forest (RF) model, with the comparison of contributions of meteorology, road traffic, and emission sources between different periods. Besides, an emulator was operated to suggest an appropriate limit for control of transportation. The RF models showed different mechanisms for air pollutants. Within-city Migration index (WMI) was more important in the normal, pre-lockdown and post-pandemic model while Out-Migration Index (OMI) was emphasized in the lockdown model. In the COVID-19 lockdown period, 73.3% of the reduction can be attributed to the decreased road traffic, showing massive impact of road traffic on the air quality. In the post-pandemic period, meteorology controlled about 42.2% of the decrease and emissions from industry and household controlled 40.0% while road traffic only contributed to 17.8%. It was suggested that priority of restriction should be given to road traffic within the city. A limit of less than 40% on the control of the road traffic can get a better effect, especially for cities with severe traffic pollution.

There is a large body of research on determining the impact of field variability of soil on crop yields. In contrast, site-specific information about crop responses to agronomic treatments is less frequent. On-Farm Precision Experimentation (OFPE) brings important information to understand the spatial variation of crop response to agronomic practices and thus to improve agronomic decisions. The objective of this work was to investigate the spatial variability of corn yield responses to nitrogen and seed rates using OFPE in four fields in the US Midwest. Geographically weighted regression was applied to generate local regression coefficients, which were used to delineate response zones in each field. The results showed the existence of great potential to adjust the rates of these inputs according to the response of each zone identified by the proposed method. The results of this study can be applied to reevaluate expectations on variable rate prescriptions guided largely by soil and variability.

Urban stormwater runoff from a medium-density residential development in southeast Queensland has been monitored in the field since November 2013. A treatment train installed on the site includes rainwater tanks collecting roofwater, 200-micron mesh baskets installed in grated gully pits and two 850 mm high media filtration cartridges installed in an underground 4 m³ vault. A monitoring protocol developed by research partners, Queensland University of Technology (QUT), guided the monitoring process over a 4.5-year period. Heavy metals were included in the list of analytes during the monitoring period as the catchment is within 1 km of the environmentally-sensitive Moreton Bay, Queensland. Removal efficiencies observed at this site for the regulated pollutants; total suspended solids (TSS), total phosphorus (TP) and total nitrogen (TN) for the pit baskets were 61%, 28% and 45% respectively. The cartridge filters removed 78% TSS, 59% TP, 42% TN, 40% total copper and 51% total zinc. As the measured influent concentrations to the cartridge filters were low when compared to industry guidelines, the dataset was merged with international field results for TSS (n=39) and TP (n=32) but truncated within anticipated guideline levels. The combined dataset for the media filter demonstrates performance at 89% TSS, 66% TP and 42% TN. The total gross pollutant generation rate from the medium-density residential catchment was observed to be 0.24 m³/Ha/year, with a corresponding air-dried mass of 142.5 kg/Ha/year. Less than 2% of the gross pollutant mass was anthropogenic. The findings of this research suggest that the treatment train, and in particular the media filter, holds promise for the removal of total copper and total zinc, in addition to TSS, TP and TN, from urban stormwater runoff. Based on a maximum, low risk trigger TN concentration of 1.5 mg/L, the field test data from 4.5 years of operation and standard maintenance, suggests a 5.5-year replacement interval for the media filters.

Microporous organic polymers (MOPs) are promising materials for gas sorption because of the intrinsic and permanent porosity, designable framework and low density. The introduction of nitrogen-rich building block in MOPs will greatly enhance the gas sorption capacity. Here, we report the synthesis of MOPs from the 2,4,6-tris(4-ethynylphenyl)-1,3,5-triazine unit and aromatic azides linkers via click polymerization reaction. FTIR and solid state 13C CP-MAS NMR confirm the formation of the polymers. CMOP-1 and CMOP-2 exhibit microporous networks with BET surface area of 431 and 406 m2 g-1 and narrow pore size distribution under 1.2 nm. Gas sorption isotherms including CO2 and H2 were measured. CMOP-1 stores superior CO2 level of 8.2 wt% (1.88 mmol g-1) at 273 K/1.0 bar and H2 uptake up to 0.6 wt% at 77 K/1.0 bar, while CMOP-2 with smaller surface area shows lower CO2 adsorption capacity of 7.3 wt% (1.66 mmol g-1) and H2 uptake (0.5 wt%). In addition, I2 vapor adsorption was tested at 353 K. CMOP-1 shows higher gravimetric load of 160 wt%. Despite of the moderate surface area, the CMOPs display excellent sorption ability for CO2 and I2 due to the nitrogen-rich content in the polymers.

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

Under the "dual carbon" target in China, virtual power plants (VPPs) play an important role in improving grid security and promoting clean and low-carbon energy transformation. VPPs can integrate and control distributed resources to participate in the energy market and make full use of distributed resources. However, the intermittency and volatility of renewable energy and the "heat-driven" working mode of CHP units create contradictions that seriously affect the peak-shaving ability of VPPs and lead to high carbon emissions. To solve these problems, this paper aggregates CHP units, wind power, photovoltaics, carbon capture, hydrogen energy storage, and electric boilers into a new type of virtual power plant. The "hydrogen energy storage-electric boiler" joint decoupling CHP working mode is used to strengthen the coupling relationship between electric-thermal-hydrogen load. At the same time, a tiered carbon trading mechanism is considered, with the net profit of the VPP as the optimization objective, balancing economic and environmental considerations. A low-carbon economic dispatch model for VPPs is established, and a genetic algorithm is used for optimization. Three different scheduling strategies are set, and simulations are conducted in three different seasonal scenarios. The results show that the net profit in the cooling season increased by 50.4%, and carbon emissions decreased by 42.3%. In the transitional season, the net profit increased by 39.2%, and carbon emissions decreased by 44.9%. In the heating season, the net profit increased by 19.4%, and carbon emissions decreased by 43.4%. Overall, the proposed dispatch strategy can improve the new energy consumption capacity and total revenue of VPPs while achieving the goal of reducing carbon emissions.

In the pursuit of sustainable solutions for carbon dioxide CO2 sequestration and emission reduction in the steel industry, this study presents an innovative integration of steelmaking slag with the modified Solvay process for sodium bicarbonate (NaHCO3) synthesis from saline brines. Utilizing diverse minerals, including electric arc furnace (EAF) slag, olivine, and kimberlite, the study explored their reactivity under varied pH conditions and examined their potential in ammonium regeneration. Advanced techniques such as XRD and ICP-OES were employed to meticulously analyze mineralogical transformations and elemental concentrations. The findings demonstrate that steelmaking slag, owing to its superior reactivity and pH buffering capabilities, outperforms natural minerals. The integration of finer slag particles significantly elevated pH levels, facilitating efficient ammonium regeneration. Geochemical modeling provided valuable insights into mineral stability and reactivity which aligned with the ICP-OES results. This synergistic approach not only aids in CO2 capture through mineral carbonation but also minimizes waste, showcasing its potential as a sustainable and environmentally responsible solution for CO2 mitigation in the steel industry.

Building on the carbon reduction targets agreed in the Paris Agreements, many nations have renewed their efforts toward achieving carbon neutrality by the year 2050. In line with this ambitious goal, nations are seeking to understand the appropriate combination of technologies which will enable the required reductions in such a way that they are appealing to investors. Around the globe, solar and wind power lead in terms of renewable energy deployment, while carbon capture and storage (CCS) is scaling up toward making a significant contribution to deep carbon cuts. Using Japan as a case study nation, this research proposes a linear optimization modeling approach to identify the potential contributions of renewables and CCS toward maximizing carbon reduction and identifying their economic merits over time. Results identify that the combination of these three technologies could enable a carbon dioxide emission reduction of between 55 and 67 percent in the energy sector by 2050 depending on resilience levels and CCS deployment regimes. Further reductions are likely to emerge with increased carbon pricing over time. The findings provide insights for energy system design, energy policy making and investment in carbon reducing technologies which underpin significant carbon reductions, while identifying potential regional social co-benefits.

With technological transformations such as big data, blockchain, artificial intelligence, and cloud computing, digital techniques are penetrating the field of finance. Digital finance is a resource-saving and environmentally friendly innovative financial service. It shows great green attributes and can drive the flow of financial resources towards environmentally friendly enterprises, thereby promoting green and low-carbon development. This paper investigates the effects of digital finance on green and low-carbon cyclic development and the mechanism. First, the level of green and low carbon cyclic development in China is estimated from multiple aspects based on the panel data of 31 provinces by using the spatio-temporal range entropy weight method. Then, the working mechanism of digital finance on green and low carbon cyclic development is revealed by performing empirical tests based on panel regression models, mediating effect models, and threshold models. Finally, the effects of digital finance and conventional variables on green and low-carbon cyclic development are investigated by using a random forest model and a CatBoost model in based on the machine learning. The results show that digital finance has significant positive effects on green and low-carbon cyclic development, and technological innovation plays a key role in the effects of digital finance on green and low-carbon cyclic development; meanwhile, the driving effect of digital finance on green and low carbon cyclic development shows nonlinear features with increasing “marginal effect”; besides, both digital finance and conventional factors have significant impacts on green and low carbon cyclic development. This study provides an empirical basis and path reference for digital finance to achieve “carbon peak, carbon neutralization” in China.

Single-molecule magnets (SMMs) have garnered significant interest in the field of molecular magnetism due to their unique magnetic properties at the nanoscale. These molecular systems exhibit magnetisation behaviour reminiscent of conventional bulk magnets but with distinct advantages such as size-dependent properties and potential applications in quantum computing and high-density data storage. However, challenges remain in harnessing their properties for practical applications, including their susceptibility to degradation and limited control over their assembly and organisation.

Multi-walled carbon nanotubes (MWCNTs) and graphene oxide (GO) reinforced carbon foam (CF) composite were prepared by direct pyrolysis of MWCNTs, GO and mesophase coal tar pitch. The effect of additive amount of the mixture of MWCNTs and GO on the microstruture and properties of carbon foam was analzyed by transmission electron miscroscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), Four-probe resistance meter, universal testing machine, and laser thermal conductivity tester respectively. The result shows that MWCNTs and GO had significant impact on the microstructure of carbon foam. Futhermore, the electrical, mechanical and thermal properties of carbon foam composites were significantly enhanced by increasing the additive amount. Maximum compressive strenght of 19.2 MPa and Young’s modulus of 56.8 MPa of CF composite were observed. Similarly, Highest thermal conductivity of 30.91 W/m.K and electrical conductivity of 27.2 ×103 S/m were observed at 2 wt. % of MWCNTs-GO additive loading.

An empirical model for log yield from trees is established and applied in microeconomics of carbon storage in a boreal spruce estate. The transition from pulpwood to sawlogs is a smoother function of stem diameter in the empirical data, in comparison to literature values. Correspondingly, the value transition of trees along with increasing size is gentler. Due to price premium of sawlogs from clearcuttings, all economically feasible treatment schedules terminate in clearcutting. Best capital return rates are gained with two heavy thinnings from above before clearcutting. Present carbon emission prices allow moderate carbon storage increment if the increment is compensated by proportional carbon rent. Doubling the present carbon prices would allow strong carbon storage increments if compensated by carbon rent. Application of nonproportional carbon rent is proposed.

Mass timber products, together with careful forestry management, could help decarbonize the construction industry. These products must be long-lasting, to safely store atmospheric carbon for decades or centuries, and multi-functional, to displace materials and equipment that are emissions-intensive. This paper shows how to optimize mass timber panels as heat-exchangers, suggesting how to eliminate insulation while simplifying HVAC systems. Test panels measured the heat-exchange in steady and transient conditions, when the ventilation was driven by a fan or by thermal buoyancy. The total heatexchange was predicted accurately by theory in all cases. Further investigation is needed to understand the possible heat-recovery effects at the exterior surface.

The expense of carbon sequestration in terms of capital return deficiency is investigated at estate level, in the case of a fertile boreal estate dominated by spruce forest. Thinnings from below result as a high expense of increased rotation age, thinnings from above as a small expense. The expense of increased timber stock is greater than any proportional carbon rent based on present carbon prices. Application of non-proportional carbon rent is proposed.

Carbon fibers (CFs) cannot be directly used for the preparation of CF paper because of their chemically inert nature. Herein, the surface of CF was modified via the spontaneous oxidative self-polymerization of dopamine. By taking full advantage of the spontaneous oxidation and self-polymerization properties of PD to maintain the maximum strength of CFs, a polydopamine-modified CF paper (PDA-CFP) with excellent performance was prepared using PD-modified CFs (PDA-CFs), which increased the proportion of hydrophilic functional groups on the surface of carbon fibers, increased the O/C ratio on the CF surface by 6 times, and improved the bond strength between the modified CF and the adhesive by making full use of the interaction force between polydopamine and PVA fibers. In this way, the primary properties of the CF paper was improved. Overall, the results showed that the dispersion of CF was considerably improved by the dopamine modification. In addition, the primary physical properties of PDA-CFP were better than those of virgin CF paper (CFP-0). PDA-CFP exhibited a maximum tensile strength of 2.04 kN/m2, a minimum resistivity of 0.06055 Ω·cm and a minimum porosity of 72.4%. The tightness could be increased by up to 12.1%.

Actuated carbon (AC) is utilized in various conditions of uses after its disclosure as a solid and dependable adsorbent. A review on AC is introduced along with returning to the wellsprings of AC age; strategies used to produce AC including pyrolysis enactment; actual actuation; synthetic initiation and steam pyrolysis. The significant variables influencing the AC creation, the potential uses of AC and their future possibilities are likewise examined. AC is applied in water, wastewater and leachate medicines in numerous nations, particularly to clean the shading, eliminate the smell and some substantial metals. Taking into account this, an exhaustive rundown of research on compound, physical and organic change strategies of initiated carbon relating to prevent of foreign substance expulsion from watery arrangements was aggregated and investigated. Additionally, the examination of the actual blending strategy and the impregnation technique in enactment with antacid metals shows that the actuated carbon got through actual blending had a higher porosity than the initiated carbon created by the impregnation technique. The uses of initiated carbon items were quickly surveyed.

In recent years, the production of cement has grown globally in a very rapid manner due to the modernization of the world we live in, and after fossil fuels and land-use change, cement production is the third-largest source of anthropogenic emissions of carbon dioxide, CO₂. Cement being the primary binding material for concrete and with the prospects for the concrete industry continues to grow so will the emissions of CO₂. Hence, a method to reduce the CO₂ production while keeping up with the progression of the concrete industry is very crucial in current times. This is where CO₂ sequestration comes in. It is a process where CO₂ is converted into a mineral which will then be trapped into the concrete forever. Required data to carry out the research between CO₂ sequestered concrete and concrete without CO₂ have been observed, obtained and tabulated as necessary. These data are then used to compare the concrete samples with one another and also prove the theoretical effects of CO₂ exposure to concrete. Hence, experimental results on the compressive strength of the concrete samples for 7, 14 and 28 days has also been tabulated, graphed and further disputed. The objective of this research is mainly to determine the compressive strength of CO₂ sequestered concrete in comparison with concrete without CO₂ in order to decrease the effects the concrete industry has on the environment. The compressive strength of concrete samples with sequestration of CO₂ gas is expected to be higher than of the concrete without CO₂.

Commercially available oxidized (carboxylic groups) and non-oxidized multiwalled carbon nanotubes were studied as adsorbents of cerium(III) in batch operation mode. Several variables affecting the rare earth adsorption were investigated, including: the stirring speed applied to the system, the pH of the solution and the metal concentration and carbon dosages. Although the removal of cerium from the solution is different and dependent upon the adsorbent type: i) adsorption in non-oxidized multiwalled carbon nanotubes, ii) cation exchange in the case of using oxidized multiwalled carbon nanotubes, the adsorption kinetics, the rate law and the isotherm models are the same for both adsorbents: pseudo-second order, film diffusion and Langmuir Type-1, respectively. Cerium is desorbed from loaded adsorbents using acidic solutions.

The present investigation deals with the adsorption of chromium(III) from alkaline media using multi-walled carbon nanotubes. The adsorption of Cr(III) has been studied under various experimental conditions: stirring speed of the aqueous solution, initial metal and adsorbent concentrations, NaOH concentration in the aqueous solution, and temperature. The rate law indicated that chromium adsorption is well represented by the particle diffusion model, whereas the adsorption process fits to the pseudo-second order kinetic model within an exothermic character. Equilibrium data fit to the Langmuir type-2 equilibrium isotherm in an spontaneous process. Chromium(III) can be eluted from metal-loaded nanotubes using acidic solutions, from which fine chromium(III) oxide pigment can be ultimately yielded.

A new bisthiourea compound, 1,3,1',3'-(dinaphthalene-1,8-diyl)bisthiourea, was synthesized. Its structure was characterized by elemental analysis, FT-IR and 1H-, 13C-NMR and MS spectroscopic techniques.

Three types of the composites were tested for electromagnetic interference (EMI) absorption shielding effectiveness, curing process and physical-mechanical properties. In the first type of composites, manganese-zinc ferrite, nickel-zinc ferrite, and both fillers in their mutual combinations were incorporated into acrylonitrile-butadiene rubber. The overall content of the filler, or fillers combinations was kept on 200 phr. Then, carbon black, or carbon fibres, respectively were incorporated into each rubber formulation in constant loading - 25 phr, while the content of magnetic fillers was unchanged - 200 phr. The work was focused on the understanding of correlation among electromagnetic shielding parameters and electrical conductivity of composites in relation to their EMI absorption shielding effectiveness. The absorption shielding ability of materials was evaluated within the frequency range from 1 MHz to 6 GHz. The study revealed good correlation among permittivity, conductivity, and EMI absorption effectiveness. Although, the absorption shielding efficiency of composites filled only with ferrites seems to be the highest, the absorption maxima of those composites were reached over 6 GHz. The application of carbon based fillers resulted in higher electrical conductivity and higher permittivity of composites, which was reflected in their lower absorption shielding performance. Though, the composites with filled with ferrites and carbon based fillers absorbed electromagnetic radiation within the desired frequency range. The presence of carbon based fillers caused the improvement in tensile behavior of composites. The study also demonstrated that the higher was the ratio of nickel-zinc ferrite in magnetic fillers combinations, the higher was the absorption shielding performance.

Flexible energy storage devices, such as solid-state supercapacitors, are becoming increasingly attractive due to their characteristics of high electrochemical performance, reliability, light weight, flexibility, absence of electrolyte leakage, high power density, and long lifetime. For the optimization of the solid-state symmetrical supercapacitor proposed in this work, it was employed in sodium and lithium form Aquivion electrolyte membrane, which serves as the separator and electrolyte. As electrode materials, carbon xerogels, synthesized by microwave-assisted sol-gel methodology, with designed and controlled properties were obtained. Commercial activated carbon (YP-50F, 'Kuraray Europe' GmbH) was used for comparison. Specifically, the developed solid-state symmetrical supercapacitors deliver sufficient high specific capacitances of 105−110 F g−1 at 0.2 A g−1, along with an energy density of 4.5 Wh kg−1 at 300 W kg−1, and in a voltage window of 0-1.2 V in an aqueous environments, also demonstrating excellent cycling stability up to 10,000 charge/discharge cycles. These results can demonstrate the potential applications of carbon xerogel as an active electrode material and cation exchange membrane as the electrolyte in the development of solid-state supercapacitor devices

With a view to sustainable development and circular economy, this work focused on the possibility to valorize a secondary waste stream of recycled carbon fiber (rCF) to produce a 3D printing usable material with PA6,6 polymer matrix. The reinforcing fibers implemented in the present research are the result of a double recovery action: starting with pyrolysis from which long fibers are obtained, used to produce non-woven fabrics and, subsequently, fiber agglomerate wastes obtained from this last process are ground in a ball mill. The effect of a different amount of reinforcement at 5% and 10% by weight on the mechanical properties of 3D printed thermoplastic composites was investigated. Although the recycled fraction was successfully integrated in the production of filaments for 3D printing and therefore in the production of specimens via Fused Deposition Modeling technique, the results showed that fibers did not improve the mechanical properties as expected, due to an unsuitable average size distribution and the presence of a predominant dusty fraction ascribed to the non-optimized ball milling process. PA6,6 + 10 wt.% rCF composites exhibited a tensile strength of 59.53 MPa and a tensile modulus of 2.24 GPa, which correspond to an improvement in mechanical behavior of 21 5 % and 5 21 % compared to the neat PA6,6 specimens, respectively. The printed composite specimens loaded with the lowest content of rCF provided the greatest improvement in strength (+ 9% over the neat sample). Then, a prediction of the “optimum” critical length of carbon fibers was proposed that could be used for future optimizations of the recycled fiber processing.

Visual data on the geographic distribution of carbon storage helps policy maker to formulate countermeasures on global warming. However, Taiwan, as an island showing diversity in climate and topography, had lacked valid visual data in distribution of forest carbon storage between the last to forest surveys (1993-2015). This study established a model to achieve an estimation that capable to demonstrate the distribution of forest carbon storage. This model uses land use, stand morphology, carbon conversion coefficient databases accordingly for 51 types of major forest in Taiwan. An estimation on 2006 was conducted and shows an overall carbon storage of 165.65 Mt C, with forest carbon storage per unit area of 71.56 t C ha–1, where natural forests and plantations respectively contributed of 114.15 Mt C (68.9%) and 51.50 Mt C (31.1%). By assuming no change in land use type, the carbon sequestration from 2006 to 2007 by the 51 forest types was estimated to be 5.21 Mt C yr–1 using historical tree growth and mortality rates. The result reflects the reality of the land use status and event of coverage shifting with time by combining to the two forest surveys in Taiwan.

This study scrutinizes the complexities of designing and exploring the potential energy surface (PES) of systems containing more than twenty atoms with planar tetracoordinate carbons (ptCs). To tackle this issue, we utilized an established design rule to design a Naphtho [1,2-b:4,3-b′:5,6-b′′:8,7-b′′′]tetrathiophene derivative computationally. This process began with substituting S atoms with CH– units, then replacing three sequential protons with two Si2+ units in the resultant polycyclic aromatic hydrocarbon polyanion. Despite not representing the global minimum, the newly designed Si8C22 system with four ptCs provided valuable insights into strategic design and PES exploration. Our results underscore the importance of employing adequate methodologies to confirm the stability of newly designed molecular structures containing planar hypercoordinate carbons.

Fossil-based emissions can be avoided through using wood in place of non-renewable raw materials as energy and materials. However, increasing wood harvest influences forest carbon stocks. This effect may reduce the overall climate benefit of wood use significantly but is widely overlooked. We carried out a systematic review of simulation studies and compared differences in forest carbon and amount of wood harvested between more and less intensive wood harvest scenarios for three different time perspectives; short (1-30 years), mid (31-70 years) and long (71-100 years). Out of more than 450 reviewed studies 44 provided adequate data. Our results show that increased harvesting reduced carbon stocks over 100 years in temperate and boreal forests roughly 1.6 (stdev 0.9) t_C per t_C harvested. The value proved to be robust when outliers explicitly influenced by other factors than change in harvest rate, such as increase in fertilization or forest area, were removed. Interestingly, no significant difference in carbon impacts was found for average values of boreal and temperate forests or between short and long time-horizons. However, impacts tend to be greatest in the mid-term. This carbon balance indicator that we estimated can be interpreted as carbon debit of wood harvest in forests. It is significant compared with the typical GHG credits in technosphere generated by avoiding fossil emissions in substitution and increase in carbon storage in harvested wood products, and should not be ignored. Our estimates provide default values that can directly be included in GHG balances of products or assessment of mitigation policies and measures related to wood use. However, more systematic scenarios and transparent data in which different factors influencing forest carbon stocks are separately studied are clearly required to provide better constrained estimates for specific forest types.

CASBEE-City tool determines the city’s Built Environment Efficiency (BEE) by calculating the improvement of Quality of Life (Q) over human activities’ Environmental Load (L) within the city’s hypothetical boundary. A total of 58 variables (57 Q indicators and one variable for L) are used in the worldwide version of CASBEE-City which were grounded using ISO 37120:2014 Sustainable Development of Communities and 17 Sustainable Development Goals (SDGs) by the United Nations (UN). This paper examines the application of CASBEE-City for Malaysian cities using the case of Johor Bahru City and identifies assessment indicators which are customised based on the data availability, reliability and suitability through focus group discussions (FGDs) which involved 36 respondents (researchers, urban planners and stakeholders). This paper reveals Johor Bahru with moderate score B+ in 2010 and 2025. Consensus were also achieved from the 36 FGD respondents for the practicability and future potential of CASBEE-City and BEE framework in Johor Bahru.

A growing number of companies in the brewery industry have made commitments to measure and reduce their greenhouse gas (GHG) emissions. However, many brewers, particularly craft brewers with relatively low rates of production, have struggled to meet these commitments. The purpose of this research was to investigate the challenges and benefits of measuring and reducing GHG emissions in the craft brewery industry. The research was conducted in Ontario, Canada, which has seen strong recent growth in the craft brewery industry. A case study and semi-structured interviews among Ontario Craft Brewers were conducted. The case study found that indirect (scope 3 emissions under the WBCSD & WRI GHG Protocol) GHG sources accounted for 46.4% of total GHGs, with major sources from barley agriculture, malted barley transportation, and bottle production. Direct emissions (scope 1) accounted for only 14.9% of GHGs, while scope 2 emissions, comprised mainly of energy consumption, accounted for 38.7% of GHGs. The case study and interviews found that the main challenges in calculating brewery GHGs are secondary data availability, technical knowledge, and finances. The study also found that the main benefits for Ontario breweries to measure their GHGs include sustainability marketing and preserving the environment. The interviews also found a poor understanding of carbon regulation among Ontario Craft Brewers, which is interesting considering that Ontario implemented a provincial cap and trade program in 2017.

The effect of hybrid carbon fillers of multi-walled carbon nanotubes (CNT) and carbon black (CB) on the electrical and morphological properties of polystyrene (PS) nanocomposites were systematically investigated in microinjection molding (μIM). The polymer nanocomposites with three different filler concentrations (i.e. 3, 5 and 10 wt%) at various weight ratios of CNT/CB (100/0, 30/70, 50/50, 70/30, 0/100) were prepared by melt blending, then followed by μIM under a defined set of processing conditions. A rectangular mold insert which has three consecutive zones with decreasing thickness along the flow direction was adopted to study abrupt changes in mold geometry on the properties of resultant microparts. The distribution of carbon fillers within microparts was observed by scanning electron microscope, which was correlated with electrical conductivity measurements. Results indicated that there is a flow-induced orientation of incorporated carbon fillers and this orientation increased with increasing shearing effect along the flow direction. High structure CB is found to be more effective than CNT in terms of enhancing the electrical conductivity, which was attributed to the good dispersion of CB in PS and their ability to form conductive networks via self-assembly. Morphology observations indicated that there is a shear-induced depletion of CB particles in the shear layer, which is due to the marked difference of shear rates between the shear and core layers of the molded microparts. Moreover, an annealing treatment is beneficial to enhance the electrical conductivity of CNT-containing microparts.

Heat stress is a serious threat to tomato production. The ultrastructure and element mapping of tomato chloroplast were investigated under different nitrogen levels to explore the regulatory effect of nitrogen on tomato chloroplast under heat stress. Experiments design two temperature treatments (25°C/15°C, as control, 40°C/30°C, as severe high-temperature, SHT ) and four nitrogen levels (0.0 kg hm-2, N1; 187.5 kg hm-2, N2; 250 kg hm-2, N3, as recommended nitrogen-application; 312.5kg hm-2 , N4) for a duration of 5 days in artificial climate chamber. The results showed that heat stress led to obvious damage to the ultrastructure of tomato chloroplast, including thylakoid stacking disorder, granum destruction, and starch grain aggregation and degradation. With the increase of nitrogen level, the ratio of long and short axes of tomato chloroplasts increased, the differentiation of chloroplasts was strengthened, the number of plastoglobuli was increased and aggregated, and the degree of damage to the ultrastructure of chloroplasts was reduced. The regulatory effect of nitrogen on the ultrastructure of tomato chloroplasts under heat stress was mainly reflected in the phosphorylation degradation process of starch granules in chloroplasts. There are obvious segmentation lines of Ca, P and Cl on both sides of the inner and outer chloroplasts, and enriched in the chloroplasts, which can outline the boundary of the chloroplasts. Element mapping analysis revealed that heat stress significantly increased the contents of calcium, phosphorus and chlorine in the chloroplast of tomato leaves, while the contents of potassium was decreased. The application of nitrogen fertilizer could significantly regulate the element distribution of tomato chloroplast under heat stress, especially the regulation of phosphorus, chlorine, calcium, magnesium. These results provide new insight into the role of nitrogen using TEM-EDX mapping in the protection of tomato chloroplast under heat stress and the mechanism of heat stress tolerance in plants.

Curdlan is a water-insoluble polymer that has structure and gelling properties useful in a wide variety of applications such as in medicine, cosmetics, packaging and the food and building industries. The capacity to produce curdlan has been detected in certain soil-dwelling bacteria of various phyla, although the role of curdlan in their survival remains unclear. One of the major limitations of the extensive use of curdlan in industry is the high cost of production during fermentation, partly because production involves specific nutritional requirements such as nitrogen limitation. Engineering of the industrially relevant curdlan-producing strain Agrobacterium sp. ATTC31749 is a promising approach that could decrease the cost of production. Here, during investigations on curdlan production, I found that curdlan was deposited as a capsule. Curiously, only a part of the bacterial population produced a curdlan capsule. This heterogeneous distribution appeared to be due to the activity of Pcrd, the native promoter responsible for the expression of the crdASC biosynthetic gene cluster. To improve curdlan production, Pcrd was replaced by a promoter (PphaP) from another Alphaproteobacterium, Rhodobacter sphaeroides. Compared to Pcrd, PphaP was stronger and only mildly affected by nitrogen levels. Consequently, PphaP dramatically boosted crdASC gene expression and curdlan production. Importantly, the genetic modification overrode the strict nitrogen depletion regulation that presents a hindrance for maximal curdlan production and from nitrogen rich, complex media, demonstrating excellent commercial potential for achieving high yields using cheap substrates under relaxed fermentation conditions.

Soil improvement methods can result in changes in the microbial community in blueberry soil. However, there have been few reports on the impacts of different soil improvement methods on the microbial function, particularly on endophytic microbe. In this study, we analyzed the response of microbial community composition, microbial function and nitrogen (N) cycle to different improvement methods using high throughput sequencing. We aimed to investigate the best soil improvement method from a microbial perspective. The results showed that the highest microbial diversity was observed in the T4 treatment (peat combined with mushroom bran), followed by the T2 treatment (peat combined with acidified rice husk) both in the rhizosphere and roots. The dominant phyla were Proteobacteria and Actinobacteria, which were most abundance in the T4 and T1 (peat combined with sulfur) treatments in the rhizosphere soil, respectively, but showed the opposite trend in the root endophytic bacterial community. Interestingly, Acidobacterium and Paludibaculum, belonging to the Acidobacteria phylum, were found to have the highest influence according to the correlation network analysis. And these bacteria were most abundant in the T2 treatment in the rhizosphere soil. The rhizosphere soil microbial communities were clustered into two categories: one for T1 and T2 treatments, and another for T3 (mushroom bran) and T4 treatments. Compared to the other treatments, the T1 treatment had the most significant impact on microbial functional pathways in the blueberry roots. T2 treatment promoted the growth of N fixation functional bacteria both in the rhizosphere soil and roots. At the module level, the T2 treatment increased the relative abundance of N fixation and decreased the relative abundance of assimilating nitrate reduction reaction (ANRA), dissimilating nitrate reduction reaction (DNRA), denitrification and completed nitrification in the blueberry rhizosphere soil. Additionally, the T2 treatment increased the abundance of root endophytic microbes involved in N fixation. Overall, our findings suggest that the addition of peat combined with acidified rice husk is the optimal soil improvement method for blueberry cultivation.

This study aimed to overcome the difficulty of conducting the horizontal-well cavity leaching test in the field and to investigate the long-term stability of the horizontal-well salt-cavity natural gas storage. The simulation test design is combined with the similarity theory to study the cavity expansion characteristics and the influence law of cavity leaching parameters. Through the design of a rubber hose connection, an integrated closed test system for multi-stage horizontal-well cavity leaching and brine drainage was built. The test system also realises the repeatable backward movement of the injection well during the test. A similarity simulation of the test design was carried out, and the test platform was constructed to carry out multi-stage horizontal-well leaching tests with a nitrogen cushion. In the horizontal-well leaching tests with a nitrogen cushion, the influence laws of the well spacing, flow rate and liquid level position on cavity expansion were investigated. Based on the morphological characteristics of the horizontal-well cavity, a numerical model of the horizontal-well salt cavity was developed, which reflects the real cavity morphology leached in the test. The long-term stability of the horizontal-well salt-cavity natural gas storage under different internal pressures was investigated through numerical simulation.

The changes in storage loss, water distribution status, gel characteristics, TBARS, total volatile basic nitrogen, and total plate count of cooked reduced-phosphate silver carp surimi batter during cold storage at 4 °C were investigated. The storage loss, content of free water, pH, hardness, TBARS, total volatile basic nitrogen value and total plate count of all cooked reduced-phosphate silver carp surimi batters significantly increased (P < 0.05) with increasing the cold storage time. Meanwhile, the content of immobilized water, whiteness, springiness, and cohesiveness decreased significantly (P < 0.05). At the same cold storage time, the sample of cooked reduced-phosphate silver carp surimi batter has lower water mobility, darker colour and better texture characteristics, but the values of TBARS, total volatile basic nitrogen and total plate count were not significantly different (P > 0.05). To sum up, the use of potassium bicarbonate instead of sodium tripolyphosphate could produce the cooked reduced-phosphate silver carp surimi batter with better water holding capacity and gel characteristics during cold storage.

Reactive oxygen species and reactive nitrogen species in semen are both essential for fertilization process; however, they become harmful at excessive levels, causing oxidative stress and nitrosative stress, respectively. Recently, oxidation–reduction potential (ORP) has been used as a marker for measuring oxidative stress, and this study investigated the possibility of comprehensively evaluating nitrosative stress. The correlation between standardized ORP (sORP) and 8-hydroxy-2′-deoxyguanosine (8-OHdG) and NOx per unit sperm was tested. Based on the previously reported cutoff value, samples were classified into oxidative stress-positive and negative groups. Thereafter, a receiver operating characteristic curve was drawn on 8-OHdG and NOx, and each optimal cutoff value was determined. Both standardized 8-OHdG and NOx significantly correlated with sORP. Although both correlated significantly with sORP in the oxidative stress group, no correlation was found in the nonoxidative stress group. The optimal standardized 8-OHdG level to determine oxidative stress status was 0.52 ng/106 spermatozoa, and the standardized NOx was 0.17 µM/106 spermatozoa/mL. The ORP is a simpler and quicker assay that can comprehensively assess oxidative and nitrosative stresses. Optimal cutoff values for both stresses were established in this study.

Soil is an extremely significant resource for human survival, and agglomerates, as the basic unit of soil structure, not only enhance soil fertility and control the biological validity of nutrients, but also strengthen the soil's erosion resistance. The mass application of fertilizers may have a significant impact on crop growth and soil structure, and the rational application and dispensing of fertilizers will be an urgent issue to be addressed. Therefore, the effect of fertilizer application on the stability of water-stable soil aggregates needs to be studied under different meteorological and soil conditions to draw more general and feasible conclusions. Our Meta-analysis of data from 220 of 56 published studies found that fertilizer application increased mean weight diameter (MWD) by an average of 18% compared to the no-fertilizer treatment. Among the nitrogen (N), phosphate (P), and organic (OM) fertilizer treatments, the organic fertilizer treatment had a greater stimulatory effect on MWD (26%). Among the different fertilizer levels, low level of phosphorus (<40kg·hm-2·yr-1), high level of N (>120kg·hm-2·yr-1), and low level of organic fertilizer (<5000kg·hm-2·yr-1) increased MWD by 19%, 14%, and 41% respectively. Across soil types and land use types, the response to MWD was positive for red soils and paddy fields, and the stimulatory effect of organic fertilizer was more significant compared to chemical fertilizer. The regression model showed that the response ratio of MWD was negatively correlated with the response ratio of soil pH and bulk density (BD), and positively correlated with the response ratio of soil organic carbon (SOC) and microbial mass carbon (MBC). Meanwhile, the PLS-SEM model showed that average annual temperature was the main factor affecting the stability of soil aggregates, and the average annual rainfall is the secondary factor. Therefore, this study found that the long-term use of organic fertilizers in place of some chemical fertilizers was more effective than chemical fertilizer alone. Temperature and rainfall have greater effects on the response of fertilizer to soil aggregate stability.

Foxtail millet (Setaria italica (L.) P. Beauv) is an important food and forage crop that is well adapted to nutrient-poor soils. However, little is known about how foxtail millet adapts to low nitrogen (LN) at the physiological and molecular levels. In the present study, two foxtail millet varieties with contrasting low nitrogen (LN) tolerance properties were investigated through integrative analyses of physiological featureparameters and transcriptomics. The physiological results showed that JG20 (high tolerance to LN) had higher biomass accumulation, nitrogen content and nitrogen use efficiency compared with JG22 (low tolerancesensitive to LN) under LN. JG20 had higher soluble sugar and soluble protein concentration in shoots compared with JG22 under LN, while contcentrations of soluble sugar and soluble protein contents were higher in the roots of JG22. Higher levels of CTK contentzeatin concentration were found in the shoots of JG20 com-pared with JG22, and a higher ABA contcentration was found in both the shoots and roots of JG22 compared with JG20 under LN. In the transcriptomics results, JG20 had more differentially ex-pressed genes (DEGs) than JG22 both in shoots and roots in response to LN. These LN-responsive genes were enriched in glycolysis, starch and sucrose metabolism, photosynthesis, biosynthesis of amino acids, hormone metabolism and nitrogen metabolism. Furthermore, the high-affinity nitrate transporter gene, SiNRT2.1, and glutamine synthetase gene, SiGS5, chlorophyll apoprotein of photosystem II gene, SiPsbQ, ATP synthase subunit gene, b, auxin-responsive protein gene, SiIAA25, and aldose 1-epimerase gene, SiAEP, in shoots, and high-affinity nitrate transporter gene, SiNRT2.3, SiNRT2.4, and glutamate synthase gene, SiGOGAT2, auxin-responsive protein gene, SiIAA4, fructose-bisphosphate aldolase gene, SiAEP5, in root, were important genes in-volved in the LN tolerance of foxtail millet. These results provide a detailed description of the physiological and transcriptome response of foxtail millet under LN condition.

We have performed the first comparative analysis of the potential of two physiologically-diverse model cyanobacteria, Synechococcus PCC 7002 (S.7002) and Synechococcus PCC 7942 (S.7942), for the photosynthetic production of four chemically-different high-value terpenes: two monoterpenes limonene and pinene, and two sesquiterpenes bisabolene and farnesene. We showed, for the first time, that S.7002 and S.7942 can produce farnesene and bisabolene, respectively. Both cyanobac-teria produced farnesene (S.7942 better than S.7002) more efficiently than the other tested terpenes (especially pinene the weakest produced terpene). S.7002 produced limonene better than bisabo-lene, whereas S.7942 produced bisabolene better than limonene. These findings suggest that S.7942 is better suited to produce sesquiterpenes than monoterpenes. Also interestingly, higher levels of terpenes were produced by S.7942 and S.7002 expressing a terpene-synthase gene from both a RSF1010-derived replicating plasmid and a neutral chromosomal site, as compared to ei-ther the plasmid alone or the chromosome alone. These results suggest that in both cyanobacteria the production of terpenes is more limited by the activity of terpene synthases than the abondance of terpene precursors. Finally, higher levels of terpenes were produced by S.7002 growing on urea (a frequent pollutant) as compared to nitrate (or ammonium) the standard nitrogen sources for cyanobacteria (more expensive than urea).

The eutrophication caused by excessive total nitrogen(TN) and total phosphorus(TP) emissions has been widely concerned by the whole society. Studies have revealed the relationship between land use and TN and TP, but the relationship between land use compound topographic position and TP and TN was seldom studied. Therefore, Spearman correlation and redundancy analyses were used to reveal the relationship between land use compound topographic position and TN and TP based on the monthly data of 28 water quality sampling sites and the land use data of 2013 and 2016 in the lakes of Guizhou Plateau. The results show that the nutritional state of the HBA watershed is medium. The trophic level index (TLI) value and TN concentration were high during flood, while TP concentration was high in dry period. The TN concentration in the tributaries was higher than that in the reservoir area. Construction and valley were the sources of the pollution, whereas forest land and gentle slope were the sink. According to the”source-sink”effect, the optimal zoning of land use was completed, and the urban land pollution govern area should be strengthened firstly. This paper can provide decision support for water environment management and sustainable development decision-making.

The C/N ratio is an extremely important parameter in the composting process, which is directly responsible for the growth of microorganisms. A low C/N ratio contributes to higher emissions of greenhouse gases and odorous substances, such as ammonia (NH3), which is formed by nitrogen mineralization. Due to the highly toxic effects of ammonia, it is a particularly unwanted by-product that can disrupt the composting process because it poisons microorganisms and cause environmental issues. The activity of anammox bacteria, so far analyzed only in wastewater treatment processes, is a particularly efficient method of nitrogen removal, having an advantage over the conventional methods used previously. Our study proofs the presence of anammox bacteria during composting, what gives an opportunity to improve the process and reduce its impact on atmospheric pollution. Despite the aerobic nature of this process, the composted mass of waste presents conditions conducive to the development of these ammonia oxidizing bacteria, as well as other strains of microorganisms cooperating with them. This makes it possible to compost at a low C/N ratio; in addition, there is no need for additional energy supply through aeration, as the processes carried out by anammox bacteria do not require oxygen.

Following legalization, cannabis has quickly become an important horticultural crop in Canada and increasingly so in other parts of the world. However, due to previous legal restrictions on cannabis research there are limited scientific data on the relationship between nitrogen (N), phosphorus (P), and potassium (K) supply (collectively: NPK) and the crop yield and quality. This study examined the response of a high delta-9-tetrahydrocannabinol (THC) Cannabis sativa cultivar grown in deep-water culture with different nutrient solution treatments varying in their concentrations (mg L^-1) of N (70, 120, 180, 250, 290), P (20, 40, 60, 80, 100) and K (60, 120, 200, 280, 340) according to a central composite design. Results demonstrated that inflorescence yield responded quadratically to N and P, with the optimal concentrations predicted to be 194 and 59 mg L^-1, respectively. Inflorescence yield did not respond to K in the tested range. These results can provide guidance to cultivators when formulating nutrient solutions for soilless cannabis production and demonstrates the utility of surface response design for efficient multi-nutrient optimization.

The mosquito microbiota reduces the vector competence of Anopheles to Plasmodium and affects host fitness, it is therefore considered as a potential target to reduce malaria transmission. While immune induction, secretion of antimicrobials and metabolic competition are three typical mechanisms of microbiota-mediated protection against invasive pathogens in mammals, the involvement of metabolic competition or mutualism in mosquito-microbiota and microbiota-Plasmodium interactions has not been investigated. Here, we describe a metabolome analysis of the midgut of An. coluzzii provided with a sugar-meal or a blood-meal, under conventional or antibiotic-treated conditions. We observed that the antibiotic treatment affects the tricarboxylic acid cycle and nitrogen metabolism, notably resulting in decreased abundance of free amino acids. Linking our results with published data, we identified candidate pathways which may participate in microbiota/Plasmodium interactions via metabolic interactions or immune modulation.

To develop green super rice varieties with high and stable yields under the rainfed conditions and improved nutrient use efficiency (NuUE), a modified backcross (BC) breeding approach was adopted using a high yielding and widely adaptable Xian variety, WTR1, as the recipient and a Geng variety, HAN, as the donor. Starting from the BC1F2 generation, the BC population had gone through one generation of selection under the IG, LI and RF conditions, followed by consecutive four generations of screening and selection for high GY under six different nutrient conditions, leading to the development of 230 BC1F6 introgression lines (ILs). The final evaluation of the 230 ILs under the six nutrient conditions identified many ILs with improved yields under various combinations of nutrient deficient conditions, including 12 promising lines that had significantly improved NuUE under two or more nutrient deficiency conditions. Our results demonstrated an efficient inter-subspecific BC breeding procedure with first round selection under the rainfed-drought condition followed by four generations of progeny testing for yield performances under six different nutrient conditions. The promising ILs were studied under replicated yield trials under 75N and -NPK conditions for developing high yield rice varieties with improved NuUE. Our results indicated that NuUE in rice was controlled by complex genetic and physiological mechanisms and the developed ILs provided useful materials for genetic and molecular dissection of NuUE in rice.

EU politics on decarbonizing shipping is an argumentative struggle in which actors try to make others see the problem and policy solutions according to their views and seek to position other actors in a specific way. This article critically analyses, by means of argumentative discourse analysis, the politics and policy process related to the recent adoption of the FuelEU Maritime regulation, the world’s most ambitious legislation for decarbonizing maritime shipping. Different storylines and discourses as well as agency of policy actors on the problems and policy options defining the meaning of decarbonization are analysed. Two discourses framed the debates, focusing on (i) incremental change and technology neutrality to meet moderate emission reductions and maintain competitiveness, and (ii) transformative change and technology specificity to meet zero emissions and gain competitiveness and global leadership in the transition towards a hydrogen economy. Policy actors successfully used discursive agency strategies such as multiple functionality and vagueness to navigate between and resolve conflicts between the two discourses. Both discourses are associated with the overarching ecological modernization discourse and failed to include issue of a just transition. The heritage of the ecological modernization discourse creates lock-ins for a broader decarbonization discourse, thus stalling a just transition.

Capturing and storing CO2 (CCS) was once regarded as a significant, urgent, and required option for reducing the emissions of CO2 from coal and oil and gas industries and mitigating the serious impacts of CO2 on the atmosphere and the environment. This recognition came about as a result of extensive research conducted in the past. The CCS cycle comes to a close with the last phase of CO2 storage, which is accomplished primarily by the adsorption of CO2 in the ocean and injection of CO2 subsurface reservoir formation, in addition to the formation of limestone by the process of CO2 reactivity with reservoir formation minerals through injectivities. CCS is the last stage in the carbon capture and storage (CCS) cycle and is accomplished chiefly via oceanic and subterranean geological sequestration, as well as mineral carbonation. The injection of supercritical CO2 into geological formations disrupts the sub-surface's existing physical and chemical conditions; changes can occur in the pore fluid pressure, temperature state, chemical reactivity, and stress distribution of the reservoir rock. This paper aims at advancing our current knowledge in CO2 injection and storage systems particularly CO2 storage methods and the challenges encountered during the implementation of each method and analyses on how key uncertainties in CCS can be reduced. CCS sites are essentially unified systems; yet, given the scientific context, these storage systems are typically split during scientific investigations based on the physics and spatial scales involved. Separating the physics by using the chosen system as a boundary condition is a strategy that works effectively for a wide variety of physical applications. Unfortunately, the separation technique does not accurately capture the behaviour of the larger important system in the case of water and gas flow in porous media. This is due to the complexity of geological subsurface systems, which prevents the approach from being able to effectively capture the behaviour of the larger relevant system. This consequently gives rise to different CCS technology with different applications, costs and social and environmental impacts. The findings of this study can help improve understanding of selecting a suitable CCS application method and can further improve the efficiency of greenhouse gas emissions and their environmental impact, promoting the process sustainability and helping to tackle some of the most important issues that human being is currently accounting global climate change. Though this technology has already had large-scale development for the last decade, some issues and uncertainties are identified. Special attention was focused on the basic findings achieved in CO2 storage operational projects to date. The study has demonstrated that though a number of CCS technology has been researched and implemented to date, choosing a suitable and acceptable CCS technology is still daunting in terms of its technological application, cost-effectiveness and socio-environmental acceptance.

Carbon subsurface storage (CSS) has already been recognised as a critical, urgent, and essential method for reducing anthropogenic CO2 emissions and mitigating the severe effects of climate change. CSS is the last stage in the carbon capture and storage (CCS) cycle and is accomplished chiefly via oceanic and subterranean geological sequestration, as well as mineral carbonation. The injection of supercritical CO2 into geological formations causes a disruption in the subsurface's existing physical and chemical conditions; changes can occur in the pore fluid pressure, temperature state, chemical reactivity, and stress distribution of the reservoir rock. This paper aims to present a comprehensive review on the current advances in CSS, particularly CO2 storage methods and the challenges encountered during the implementation of each methods and analyses on how key uncertainties in CSS can be reduce. CSS sites are essentially unified systems; yet, given the scientific context, these systems are typically split during scientific investigations based on the physics and temporal/spatial scales involved. Separating the physics by using the system as a boundary condition is a strategy that works effectively for a wide variety of physical applications. Unfortunately, the separation technique does not accurately capture the behaviour of the larger important system in the case of water and gas flow in porous media. This is due to the complexity of geological subsurface systems, which prevents the approach from being able to effectively capture the behaviour of the larger relevant system. This consequently give rise to different CSS methods. A good CSS application method can further improve the efficiency of greenhouse gas emission and their environmental impact, promoting the process sustainability and helping to tackle some of the most important issues that human being is currently accounting, global climate change. Though this technology is already large-scale development for the last decade, some issues and uncertainties are identified. Special attention was focused on the basic findings achieved in CO2 storage operational projects to date.

The goal of this work is to develop a sustainable value chain of carbonaceous adsorbents that can be produced from the solid fibrous digestate (SFD) of biogas plants and further applied in integrated desulphurisation-upgrading (CO2/CH4 separation) processes of biogas to yield high purity biomethane. On this purpose, physical and chemical activation of the SFD derived biochar was optimised to afford micro-mesoporous activated carbons (ACs) of high BET surface area (590-2300 m2g−1) and enhanced pore volume (0.57-1.0 cm3g−1). Gas breakthrough experiments from fixed bed columns of the obtained ACs, using real biogas mixture as feedstock, unveiled that the physical and chemical activation conclude to different types of ACs which are sufficient for biogas upgrade and biogas desulphurisation respectively. Performing breakthrough experiments at three temperatures close to ambient it was possible to define the optimum conditions for enhanced H2S/CO2 separation. It was also concluded that the H2S adsorption capacity is significantly affected by restriction to gas diffusion. Hence, the best performance was obtained at 50 oC and the maximum observed in the H2S adsorption capacity vs the temperature is attributed to the counterbalance between adsorption and diffusion processes.

Riverine particulates dominate the transport of vital nutrients like Si, Fe or P to the ocean mar-gins, where they may increase primary production by acting as slow release fertilizer. Further-more, the supply of particulate surface area to the ocean is considered to be a major control or-ganic carbon burial. Taken together, these observations suggest a close link between the supply of riverine particulate material and the organic carbon cycle. To explore this link, we conducted microcosm experiments to measure the growth of the marine diatom Thalassiosira weissflogii in the presence and absence of different types and concentrations of riverine particulate material. Results demonstrate a strong positive effect of riverine particulate material on diatom growth with increased total diatom concentrations and slowed post-exponential death rates with in-creasing particulate concentration. Moreover, SEM and optical microscope investigations con-firm that riverine particulates facilitates organic carbon burial through their role in the aggrega-tion and sedimentation of phytoplankton. The supply of riverine particulate material has been shown to be markedly climate sensitive with their fluxes increasing dramatically with increas-ing global temperature and runoff. This pronounced climate sensitivity implies that riverine particulates contribute substantially in regulating atmospheric CO2 concentrations through their role in the organic carbon cycle.

Forests play an important role in reducing greenhouse gases in the atmosphere, thereby mitigating the impact of climate change. Estimating the accumulated biomass in a forest ecosystem is important for assessing the productivity and sustainability of the forest. Allometric models for above ground biomass (AGB) are linear regression equations based on the relationships between biomass and diameter at breast height (DBH), tree height (H), and/or wood density. This study estimates AGB in the Colo-I-Suva Forest Park by applying the allometry of Chave et al (2005) and the diameter: height ratio derived from Payton & Weaver (2011) for height estimation in a plot of 20

For every three people on the planet there is approximately two Tonne (Te) of available plastic waste. We show that carbon recovery from polystyrene (PS) plastic is enhanced by the co-addition to solvents to grow carbon nanotubes (CNTs) by liquid injection chemical vapour deposition. Polystyrene was loaded up to 4 wt% in toluene and heated to 780 °C in the presence of a ferrocene catalyst and a hydrogen/argon carrier gas in a 1:19 ratio. High resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and Raman spectroscopy were used to identify multi-walled carbon nanotubes (MWCNTs). The PS addition in the range from 0 to 4 wt% showed improved quality and CNT homogeneity; Raman “Graphitic/Defective” (G/D) values increased from 1.9 to 2.3; mean CNT diameters increased from 43.0 to 49.2 nm; and maximum CNT yield increased from 11.3% to 14.2%. Since both the CNT diameters and the percentage yield increased with respect to polystyrene addition, we conclude that carbon from the PS contributes to the carbon within the MWCNTs. The electrical contact resistance of acid washed Bucky papers produced from each loading, ranged from 2.2 to 4.4 Ohm, with no direct correlation to PS loading. Due to this narrow range, the materials with different loading were mixed to create six wires of an Ethernet cable and tested using iPerf to give uplink and downlink speeds of ~99.5 Mbps, comparable to Cu wire of identical dimension (~99.5 Mbps). The lifecycle assessment (LCA) of CNT wire production was compared to copper wire production for the use case in a Boeing 747-400 over the lifespan of the craft. Due to their lightweight nature the CNT wires decreased the CO2 footprint by 21 kTonne (kTe) over the aircraft lifespan.

Spin dependent quantum transport properties in twisted carbon nanotube and stretched carbon nanotube are calculated using density functional theory (DFT) and non-equilibrium green’s function (NEGF) formulation. Twisting and stretching have no effect on spin transport in CNTs at low bias voltages. However, at high bias voltages the effects are significant. Stretching restricts any spin-up current in antiparallel configuration (APC) which results in higher magneto resistance (MR). Twisting allows spin-up current almost equivalent to the pristine CNT case resulting in lower MR. High spin filtration is observed in PC and APC for pristine, stretched and twisted structures at all applied voltages. In APC, at low voltages spin filtration in stretched CNT is higher than in pristine and twisted ones with pristine giving higher spin filtration than twisted CNT.

Confronting the dual challenges of rapid urbanization and climate change, although extensive research has investigated the influencing factors and practical strategies of urban carbon emissions and urban vibrancy, respectively, the unclear mutual nexus between them and the development strategy of collaborative optimization requires further in-depth analysis. This study explores the delicate balance between urban vibrancy and low-carbon sustainability within the confines of Beijing’s Fifth Ring Road. By integrating OpenStreetMap, land use, population, and building carbon emission data, we have developed a reproducible method to estimate total carbon emission and emission intensity per capita. Furthermore, we have introduced vibrancy index data to distinguish the vibrancy evaluation of residential and non-residential land and applied cross-combinational classification technology to dissect the spatial correlation between urban carbon emissions and urban vibrancy. The results reveal that the four combination typologies show more significant differences and regularity in residential land. Based on the discovery of spatial correlation, this study puts forward corresponding development strategy suggestions for each typology based on geographical location and the requirements of urban development policies of these four combination typologies. In conclusion, our study highlights the importance of integrating carbon emissions and urban vibrancy comprehensively in sustainable urban planning and proposes that various land use combinations need targeted development strategies to achieve this goal, which need to consider population, energy, service facilities, and other diverse aspects.

The nucleation of voids in alpha iron and the influence of carbon were investigated through a combination of rate theory and nucleation theory calculations. The steady rates of void nucleation exhibit high sensitivity to carbon. Even a seemingly negligible carbon concentration, as low as a few atomic parts per million (appm), can dramatically reduce the nucleation rates and narrow the temperature window for nucleation. This study highlights the challenges in certifying and qualifying nuclear materials for use in reactor environments. It emphasizes the necessity for precise control of impurity levels during materials processing and stringent requirements for irradiation testing, which are susceptible to contamination. Furthermore, the study provides an explanation for the significant data scattering observed in void swelling behaviors as reported in the literature.

In this study, carbon-quantum-dot (CQD)-decorated TiO2 was prepared using an ultrasonic doping method and applied in the photocatalytic degradation of naphthalene under sunlight irradiation. The CQDs were synthesized from a typical macroalgae via diluted sulfuric acid pretreatment and hydrothermal synthesis using an optimal design, i.e., 3 wt% and 200 oC, respectively. The CQD/TiO2 composite remarkably enhanced the photocatalytic activity. The degradation of naphthalene under a visible light environment indicated that there is a synergistic mechanism between CQDs and TiO2, in which the generation of reactive oxygen species is significantly triggered; in addition, the N that originated from the macroalgae accelerated the photocatalytic efficiency. Kinetic analysis showed that the photo-catalytic behavior of the CQD/TiO2 composite followed a pseudo-first-order equation. Consequently, our combined experimental approach not only provides a facile pretreatment process for bio-CQDs synthesis, but also delivers a suitable TiO2 photocatalyst for up-conversion, along with critical insights into the development of harmful macroalgae resources.

The excellent properties of carbon fibers, in combination with the high price of carbon fibers, makes it interesting to recycle these fibers. Pyrolysis is already an established recycling method to recover the carbon fibers, but in this process also the sizing is removed which could result in lower mechanical properties because of bad adhesion between the fiber and matrix. In this study, recycled carbon nonwoven reinforcements made from pyrolyzed carbon fibers were pre-treated in order to improve the mechanical properties of recycled carbon polyamide and recycled carbon polypropylene composites. The pre-treatment involves applying a to the matrix adapted primer coating to the nonwoven by spraying. Via compression molding, polyamide and polypropylene composites were prepared with and without pretreatment. The tensile and interlaminar shear strength of these composites were measured to determine the effect of the pretreatment. Results revealed that both strengths could be increased by pretreatment of the carbon nonwoven and the increase was largest for the PP composites.

Epoxy matrix composites reinforced with high-performance fibers such as carbon, Kevlar, and glass, exhibit excellent specific stiffness and strength in many mechanical applications. However, these composites are disappointingly non-recyclable and are usually disposed of in landfill sites, with no realistic prospect for biodegradation in reasonable time. In contrast, moldable composites with carbonized elastomeric matrices developed in the last decades possess attractive mechanical properties in final net-shape products and can also be incinerated or recycled. Many carbon and inorganic fillers have recently been evaluated to adjust the properties of carbonized elastomeric composites. Renewable organic fillers such as human or animal hair offer an attractive fibrous material with substantial potential for reinforcing composites with elastomeric matrices. Samples of unidirectional fiber composites (with hair volume fraction up to 7 %) and quasi-isotropic short fiber composites (with hair volume fraction up to 20 %) of human hair-reinforced nitrile butadiene rubbers (HH-NBR) were produced in the peroxide-cured and carbonized states. The samples were characterized using SEM, Raman spectroscopy and photoacoustic microscopy. Mechanical tests were performed in tension using a miniature universal testing machine. The expected effect of fiber reinforcement on the overall mechanical performance has been demonstrated for both cured and carbonized composites. Considerable enhancement of the elastic modulus (up to 10 times), ultimate tensile strength (up to 3 times) and damage tolerance was achieved. The evidence of satisfactory interfacial bonding between hair and rubber was confirmed by SEM imaging of fracture surfaces. The suitability of photoacoustic microscopy was assessed for 3D reconstruction of the fiber sub-system spatial distribution and non-destructive testing.

Among various processes, catalytic CO2 methanation has emerged as a promising method for carbon capture and utilization. Therefore, a CO2 methanation reaction studied with experimentally. The extent of coke formation on the catalyst after the reaction was quantitatively studied. Then, four different machine learning model were employed in order to model CO2 methanation process and to predict CO2, CO, CH4, H2 and N2 concentrations at outlet. The results of the machine learning models were consistent with the experimental data. Performances of the proposed regression methods are evaluated with 10-fold cross validation. Random forest and decision tree regression performed the best among other methods by achieving R >0.98 for the output concentrations and were able to outperform other modeling approaches. It was shown that the best result among the literature studies is reached in this study. The results have demonstrated the possibility of simulation of the methanation process via machine learning techniques. These techniques can be used control and optimization of carbon capture.

Hypoxia, associated with abnormal vessel growth, is a characteristic feature of many solid tumors that increases their metastatic potential and resistance to radiotherapy. Carbon ion radiation therapy, alone or in combination with other treatments, is one of the most promising treatments for hypoxic tumors because the oxygen enhancement ratio decreases with increasing particle LET. Nevertheless, the current clinical practice does not yet fully benefit from using carbon ions for tackling hypoxia. Here we give an overview of the existing experimental and clinical evidence supporting the efficacy of C-ion radiotherapy in overcoming hypoxia-induced radioresistance, followed by a discussion of the strategies proposed to enhance it, including different approaches to maximize the LET in the tumors.

Despite providing some critical financial services to support the operation of Emissions Trading Systems (ETS), such as increasing market liquidity and price visibility and allowing operators to hedge against future fluctuations, there is growing concern about the potential threat of financial actors' speculation behaviour to the ETS's effectiveness. To confirm or alleviate the fear associated with such concern, we employ both ex-post and ex-ante approaches to determine the role of speculation in the emission reduction effect of the ETS and its forecasting power in predicting climate change. In addition to confirming carbon prices and the speculation behaviour of the emissions non-compliance actors in the ETS as accurate predictors of climate change, we also show that they both matter in the emission reduction effect of the ETS. We use several verifiable econometric approaches to select the Feasible Quasi Generalised Least Squares (FQGLS) as the best estimator for addressing some of the biases in climate change predictability. We demonstrate that a predictive model combining the complementing dynamics of the EST emissions compliance and emissions non-compliance features forecasts climate change more accurately. We demonstrate the robustness of our findings for both in-sample and out-of-sample forecasts and across different forecast horizons by using alternative approaches to evaluate forecast performance.

In this work we successfully prepared a modified cobalt oxide (Co3O4) carbon paste electrode to detect Levofloxacin (LEV). By synthesizing Co3O4 nanoparticles through the chemical coprecipitation method, the electrochemical properties of the electrode and LEV were thoroughly investigated using CV, SWV, EIS, while material properties were scrutinized using ICP-OES, TEM, SEM, and XRD. The results showed that the prepared electrode displayed a better electrocatalytic response than the bare carbon paste electrode. After optimizing SWV, the electrode exhibited a wide linear working range from 1 to 85 μM at pH 5 of BRBS as the supporting electrolyte. The selectivity of the proposed method was satisfactory, with good repeatability and reproducibility, strongly suggesting a potential application for determining LEV in real samples, particularly in pharmaceutical formulations. The practicality of the approach was demonstrated through good recoveries, and the morphology of the materials was found to be closely related to other parameters, indicating that the developed method can provide a cost-effective, rapid, selective, and sensitive means for LEV monitoring. Overall, this project has made significant progress towards developing a reliable method for detecting LEV and has opened up new opportunities for future research in this field.

Carbon dots have received much attention due to their unique physicochemical properties and diverse applications in bioimaging, optoelectronic devices, catalysis, and agriculture. Here in this work, we report a simple hydrothermal synthesis of nitrogen and phosphorus-doped carbon dots (N, P-CDs). The optical and physical properties of the synthesized N, P-CDs were analyzed using systematical spectroscopy and electrical characterization. The synthesized N, P-CDs show strong photoluminescence at 626 nm and demonstrate high stability under UV light and other conditions. Moreover, we incorporate the synthesized N, P-CDs into water spinach by root spraying and leaf spraying. It was found that N, P-CDs could effectively promote the growth of water spinach by increasing the photosynthetic rate, and the content of total phenols and anthocyanins in water spinach

With the rapid and continuous advancement and deployment of advanced energy storage de-vices, there has been significant interest in aqueous capacitors that possess non-flammable properties and high safety features. Consequently, extensive research efforts have focused on investigating zinc anodes and low-cost carbonaceous cathode materials. Despite these efforts, the development of high-performance zinc-ion capacitors (ZICs) still faces challenges such as limited cycling stability and low energy densities. In this study, we present a novel approach to address these challenges. We demonstrate the utilization of a three-dimensionally (3D) grown conductive porous carbon framework cathode coupled with zinc anode cells, which exhibit exceptional sta-bility and durability in ZICs. Our experiments reveal a remarkable cycling performance, with a capacity retention of approximately 97.3% and a coulombic efficiency of nearly 100% even after 10,000 charge-discharge cycles. These findings signify significant progress in enhancing the performance of ZICs.

Activated carbon (AC) is an effective adsorbent for creatinine removal in hemoperfusion. However, the hemocompatibility and adsorption capacity of AC was required to be improved furthermore. Heparin, a widely used anticoagulant biomacromolecule, could improve the hemocompatibility of the absorbents in different ways based on its molecular weight. Thus, it was necessary to study the surface modification with unfractionated heparin (UFH) or low molecular weight heparin (LMWH) on improvement of hemocompatibility and adsorption. In this study, UFH and LMWH were respectively grafted on AC through polyethyleneimine as an intermediate layer. The modification of AC about morphology, mechanical strength and pore structure was characterized by XPS, SEM, TA and BET. It was found that compared with AC, the morphology and mechanical strength AC-UFH and AC-LMWH could be well maintained, but the BET surface was decreased due to the grafting of macromolecules. Furthermore, AC-UFH and AC-LMWH showed the better hemocompatibility on protein adsorption, APTT and platelet activation compared with AC, in which AC-LMWH had lower fibrinogen adsorption and longer APTT than AC-UFH. Besides, it was found that AC, AC-UFH and AC-LMWH had no significant effect on blood cell composition. Finally, the adsorption capacity of adsorbents for creatinine was evaluated. Although there was no significant difference between AC-UFH and AC-LMWH, it was found that heparin could be interacted with creatinine to enhance the adsorption capacity when compared with AC-PEI. This study deepened the understanding of anticoagulation of heparinized surface and provided a theoretical basis for adsorbents in hemoperfusion.

Carbon monoxide (CO) is a cytoprotective endogenous gas that is ubiquitously produced by the stress response enzyme heme-oxygenase. Being a gas, CO rapidly diffuses through tissues and binds to hemoglobin (Hb) increasing carboxyhemoglobin (COHb) levels. COHb can be formed in the erythrocytes or in plasma from cell-free Hb. Herein, it is discussed whether endogenous COHb is or is not an innocuous and inevitable metabolic waste product and it is hypothesized that COHb has a biological role. In the present review literature data is presented to support this hypothesis based on two main premises: (i) there is no direct correlation between COHb levels and CO toxicity; and (ii) COHb seems to have a direct cytoprotective and antioxidant role in erythrocytes and in hemorrhagic models in vivo. Moreover, CO is also antioxidant by generating COHb, which protects against the pro-oxidant damaging effects of cell free Hb. Up to now COHb has been considered as a sink for both exogenous and endogenous CO generated during CO intoxication or heme metabolism, respectively. Hallmarking COHb as an important molecule with a biological (and eventually beneficial) role is a turning point on CO Biology research, namely in CO intoxication and CO cytoprotection.

The build-up of greenhouse gases (GHGs) is causing warmness in the Earth’s atmosphere, resulting in climate change. The transport sector is one of the active members of GHG emissions and it is imperative to use sustainable transport sources to control climate change. The measure aims to encourage citizens to stop using their private vehicles as their choice of transport and instead opt for joint sustainable mobility during traveling. In this study, a quantitative research method was used and data were collected from a sample of 410 respondents through questionnaire. On the other hand, study also took a simulation-based (N=10000) sample size of private vehicle data. The data were analyzed using structural equation modelling. The results revealed that sustainable transportation, climate change technologies and electric rail vehicles reduce climate change in the ecoregions of China. We conclude that sustainable transportation policies could be formulated and implemented to reduce climate change. In response to the research results, it is recommended that, since climate change is a multi-level governance issue and the outdated pyramidal transport industry models must be shifted to a sustainable transportation system model.

Background There is increasing awareness of problems associated with global warming but a lack of a systematic approach on how to deliver more environmentally sustainable dental care. A sustainable world aims to ensure that basic needs and quality of life of everyone are met, now and for future generations. The carbon footprint is an indicator of environmental sustainability. Aim The aim is to suggest an environmental management change for the dental practice focusing on the objective of carbon footprint reduction. Environmental management change design The management change is based on the concept of “Plan-Do-Check-Act”, as recommended by the International Organisation for Standardisation (ISO) and described through the environmental aspects of the dental practice. The approach focuses on establishing and implementing environmental objectives, followed by monitoring results and taking actions to improve continually. The environmental aspects considered for the dental practice are activities causing an impact on the carbon footprint: energy use, travel, product purchasing, waste production, emission to air, water use, and contamination of land. Conclusions The “Plan-Do-Check-Act” ISO 14100-2015 model can be effectively integrated into the dental practice setting for its environmental management. A reduction of the carbon footprint of the dental practice is achieved by applying the environmental management change described for each activity.

The direct growth of single-walled carbon nanotubes (SWCNTs) with a narrow distribution of diameter or chirality remains elusive despite significant benefits in properties and applications. Nanoparticle catalysts are vital for SWCNT synthesis, but how to precisely manipulate their chemistry, size, concentration, and deposition remains difficult, especially within a continuous production process from the gas-phase. Here, we demonstrate the preparation of W₆Co₇ alloyed nanoparticle catalysts with precisely tunable stoichiometry using electrospray, which remain solid state during SWCNT growth. We also demonstrate continuous production of liquid iron nanoparticles with in-line size selection. With the precise size manipulation of catalysts in the range of 1-5 nm, and a nearly monodisperse distribution (σ_g < 1.2), an excellent size selection of SWCNT can be achieved. All of the presented techniques show great potential to facilitate the realization of single-chirality SWCNT production.

Researchers’ attention has been turned on Health expenditure, Carbon emissions, and economic growth as they play a focal role in the current debate on environmental protection and sustainable development. Our paper endeavors to investigate the impact of economic growth and CO2 emissions on Health expenditure for two main countries in Asia (China and India) using a dynamic panel data model estimated employing the Generalized Method of Moments (GMM) for the period 1960–2019. Our empirical results show that there is a significant relationship between health expenditure, CO2 emissions, and economic growth. The empirical evidence indicates a significant positive impact of CO2 emissions on health expenditure whiles economic growth has a negative impact on health expenditure for both countries for the period under study. The population growth rate has transposed effect on India's health spending; on the other hand, its impact on China’s health spending is significantly positive. The strong observable correlation between health expenditure and economic growth is crucial for economic development.

Graphite nanoplatelets (GNPs) were produced from flake graphite that had been immersed in isopropyl alcohol solution (70%) and converted to powder form in an ultrasonic bath (5 h, room temperature). Scanning and transmission electron microscopy, X-ray diffractometry, and Raman spectroscopy identified 120-nm-thick GNP crystallites and 0.5–21 µm plates with different areas and shapes. Extensive exfoliation was observed by transmission electron microscopy with abundant multilayer and some monolayer GNPs. X-ray diffractometry confirmed 43 GNP layers along the c-axis. Raman spectroscopy indicated well-defined GNPs with few defects and no oxide content. Rietveld analysis indicated a GNP crystal lattice with stacks of parallel two-dimensional graphene layers and tightly bound hybridized carbon atoms stacked in a translational …ABAB… sequence in hexagonal rings.

A methodology is proposed for designing the stabilization process of polyacrylonitrile (PAN) fibers. In its core, this methodology is based on a model that describes the characteristic fiber length change during the treatment, through the de-convolution of the three main contributors (i.e. entropic shrinkage, creep, and chemical shrinkage). The model has the additional advantage of offering further insight into the physical and chemical phenomena taking place during the treatment. Validation of PAN-model prediction performance for different processing parameters was achieved as demonstrated by FTIR and DSC. Τensile testing revealed the effect of processing parameters on fiber quality, while model prediction demonstrated that ladder polymer formation is accelerated at temperatures over 200oC. Additionally, according the DSC and FTIR measurements predictions from the application of the model during stabilization seem to be more precise at high-temperature stabilization stages. It was shown that mechanical properties could be enhanced preferably by including a treatment step below 200oC, before the initiation of cyclization reactions. Further confirmation was provided via Raman spectroscopy, which demonstrated that graphitic like planes are formed upon stabilization above 200oC, and thus multistage stabilization is required to optimize synthesis of carbon fibers. Optical Microscopy proved that isothermal stabilization treatment did not severy alter the cross section geometry of PAN fiber monofilaments.

The behaviour of oxidized and non-oxidized multiwalled carbon nanotubes in the adsorption of lanthanum(III) from aqueous solutions is described. Metal uptake is studied as a function of several variables such as the stirring speed of the system, pH of the aqueous solution and metal and nanomaterial concentrations. The experimental results are fitted to various kinetics and isotherm models, being the rate law fitted to the film diffusion and particle diffusion models, when the non-oxidized and the oxidized nanomaterials are used to remove lanthanum from the solution, respectively. Sulphuric acid solutions seem to be appropriate to recover the metal from La-loaded nanomaterials.

The Philippines is both a biodiversity hotspot and a megadiverse country. The country also has experienced one of the highest rates of deforestation in Southeast Asia and is among the first countries to introduce a massive reforestation program to address the country’s rapid biodiversity and forest loss. Drawing upon an empirical study from the Leyte island and other relevant case studies from the Philippines, in this chapter, we demonstrate that recovering secondary forests following shifting cultivation, locally known as kaingin have the high potentials for biodiversity and carbon co-benefits. Based on our empirical study, we also found that secondary forest regrowing after kaingin use can potentially be used as a cost-effective reforestation measure with multiple benefits to people and the environment in upland areas of the Philippines. We also discuss measures that are essential for such programs to be successful.

This article presents the copper ions adsorption process using an activated carbon from winemaking wastes. The pH, temperature, activated carbon amount and initial copper concentration were varied based on a full factorial 2^k experimental design. Kinetic and thermodynamic studies were also carried out. The adsorption kinetics was found follow a pseudo-second-order model. The adsorption data fit better to the Langmuir isotherm. The ANOVA demonstrated that both pH of the solution and activated carbon dosage had the greatest influence on copper adsorption. The activation energy was -32 kJ·mol^-1 suggesting that the copper adsorption is a physic-sorption process. The best fit to a linear correlation was the moving boundary equation that controls the kinetics for the adsorption copper ions onto the activated carbon. The X-ray photoelectron spectroscopy (XPS) results reveal the existence of different copper species (Cu²⁺, Cu⁺ and or Cu⁰) on the surface of the carbonaceous adsorbent after the adsorption, which could suggest a simultaneous reduction process.

The harmful nature of high concentrations of antibiotics to humans and animals requires urgent development of novel materials and techniques for their absorption. In this work, CTAB (Cetyltrimethyl Ammonium Bromide)-assisted synthesis of ZIF-8 (zeolitic imidazolate framework) derived hollow carbon (ZHC) was designed, prepared and used as a high-performance adsorbent, further evaluated by Langmuir and Freundlich isothermal adsorption experiments, dynamic analysis as well as theoretical calculation. The maximum capacities of ZHC on adsorbing tetracycline (TC), norfloxacin (NFO) and levofloxacin (OFO) are 267.3, 125.6 and 227.8 mg g^-1, respectively, which delivers superior adsorptive performance when compared to widely studied inorganic adsorbates. The design concept of ZIFs-derived hollow carbon material provides guidance and insights for the efficient adsorbent of environmental antibiotics.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

Balsam fir trees are a specialty agricultural species that are largely used as Christmas trees. Soil or tissue sampling is seldom performed to assess balsam fir nutrition needs, which can contribute to over or under fertilization and subsequent environmental challenges. Remote sensing to determine the normalized difference vegetation index (NDVI) has had strong relationships with nutrition in other plants. This research aimed to determine whether there is a relationship between NDVI and nutrition in balsam fir. A random sample of 45 trees was selected in autumn of 2021 and then another 70 trees selected in spring of 2022. Soil and needle tissue samples were analyzed for N, P, K, Ca, Mg, S, Fe, Zn, Mn, B, and Cu. An uncrewed aerial vehicle equipped with a multispectral camera was flown over the orchard to determine the NDVI for each tree. Nutrition and NDVI were analyzed for correlations through all sampled trees. Separate correlation analyses were repeated for mature trees (greater than 5 years old) and young trees (less than 5 years old). Soil nutrients N, P, K had a significant relationship with NDVI in autumn sampling. Only N was correlated consistently in both autumn and spring, with R2 of 37% and 33% respectively. Relationships were much stronger when only mature trees were considered, increasing to 60% and 51% respectively. NDVI was found to offer predictive power for tissue N that can be useful to producers to help optimize fertilizer input. However, further work is needed to refine these relationships.

In this study, long-term mortality effects associated with exposure to PM10, PM2.5, BC (black carbon), and NOx were analyzed in a cohort in southern Sweden during the period from 1991‒2016. Participants (those residing in Malmö, Sweden, born between 1923‒1950) were randomly recruited from 1991‒1996. At enrollment, 30,438 participants underwent a health screening, which consisted of questionnaires about lifestyle and diet, a clinical examination, and blood sampling. Mortality data were retrieved from the Swedish national cause of death register. The modeled concentrations of PM10 (particles with an aerodynamic diameter smaller than or equal to 10 µm), PM2.5 (particles with an aerodynamic diameter smaller than or equal to 2.5 µm), BC (black carbon), and NOx (nitrogen oxides) at the cohort participants' home addresses were used to assess air pollution exposure. Cox proportional hazard models were used to estimate the associations between long-term exposure to PM10, PM2.5, BC, and NOx and the time until death among the participants during the period from 1991‒2016. The hazard ratios (HRs) associated with an interquartile range (IQR) increase in each air pollutant were calculated based on the exposure lag windows of the same year (lag0), 1‒5 years (lag1‒5), and 6‒10 years (lag6‒10). Three models were used with varying adjustments for possible confounders including both single-pollutant estimates and two-pollutant estimates. With adjustments for all covariates, the HRs for PM10, PM2.5, BC, and NOx in the single-pollutant models at lag1‒5 were 1.06 (95% CI: 1.02‒1.11), 1.01 (95% CI: 0.95‒1.08), 1.07 (95% CI: 1.04‒1.11), and 1.11 (95% CI: 1.07‒1.16) per IQR increase, respectively. The HRs were in most cases decreased by the inclusion of a larger number of covariates in the models. The most robust associations were shown for NOx, with statistically significant positive HRs in all models. An overall conclusion is that road traffic-related pollutants had a significant association with mortality in the cohort.