Infertility affects approximately 15% of couples worldwide, an estimated 30% of which is related to male factor infertility. Application of low level laser therapy (LLLT) to improve fertility status is a rapidly growing discipline in medicine. Laser therapy triggers a variety of biological processes through interaction with primary cellular photoacceptors. The present review aims at evaluating the literature available in the MEDLINE/ PubMed on cellular and molecular mechanisms of photobiomodulation in the domains of reproductive and veterinary medicine. We primarily focused on the clinical application of laser treatment on seminal quality, in particular its role in promoting spermatozoa motility, as well as the role of phototherapy in modulating assisted reproduction (ART). Additionally, we investigated the strength of evidence in support of the positive impact of photobiomodulation on facilitating ART.

This study evaluated the effect of low-level laser irradiation induces by diode laser on the speed of orthodontic tooth movement of canines submitted to initial retraction. Twenty-four mandibular canines were retracted by using NiTi spring (force of 150 g/side). Thirteen of those were irradiated with a diode laser 980-nm diode laser (Wiser Laser Doctor Smile, Lambda) operating at an 810-nm wavelength (1 W of output power, continuous wave of 66.7 J/cm2) that was equipped with a 0.6-mm optical fiber in continuous-wave mode. The canine retraction was accomplished by using prefabricated coil springs. The right of the mandible was chosen to be irradiated with the laser, whereas the left side was considered the control without laser irradiation. The laser was applied with 0-, 3-, 7-, and 14-day intervals. The amount of canine retraction was measured with a digital electronic caliper while the pain level was prompted by a patient questionnaire. The speed of tooth movement was significantly greater in the laser group than in the control group. The pain intensity was also at a lower level in the laser group. Our findings suggest that diode laser therapy can highly accelerate tooth movement during orthodontic treatment and can also effectively reduce pain level.

Background: Low-level (LLLT) and high-intensity laser therapy (HILT) can be beneficial additions to knee osteoarthritis (KOA) rehabilitation exercises; however, it is still being determined which modality is more effective. Aim: To compare the effects of LLLT and HILT as adjuncts to rehabilitation exercise (LL+EX and HL+EX) on clinical outcomes in KOA. Methods: Thirty-four adults with mild to moderate KOA were randomly allocated to either LL+EX (n = 17) or HL+EX (n = 17) groups. All participants underwent their designated laser treatment combined with rehabilitation exercises weekly for twelve consecutive weeks. The Knee Injury and Osteoarthritis Outcome Score (KOOS), Numerical Pain Rating Scale (NPRS), active knee flexion, and Timed Up-and-Go test (TUG) were assessed at baseline and immediately post-intervention. Results: Post-intervention, both groups significantly improved their KOOS, NPRS, active knee flexion, and TUG scores compared to baseline (p < 0.01). The mean difference of change in KOOS, NPRS, and active knee flexion scores for the HL+EX group surpassed the minimal clinically important difference threshold. In contrast, the LL+EX group only demonstrated clinical significance in NPRS scores. Conclusions: Incorporating HILT as an adjunct to usual KOA rehabilitation led to significantly higher improvements in pain, physical function, and knee-related disability compared to LLLT.

Background:This study evaluated the effect of low-level laser therapy on postoperative pain and wound healing in children undergoing primary molar extractions.Methods:40children,6-10years of age, systemically healthy, and had atraumatic extraction indications of bilateral primary molar teeth were included in the study. First session randomly selected tooth was extracted under local anesthesia. In the control group, only the clot formation on the socket was observed and photographed. Other group extraction's performed 2weeks later. The LLLT group treated with980nm wavelength Doctor Smile Wiser diode laser and photographed. Non-epithelialized surface measurements performed with the ImageJ program. Pain assessment was performed with Wong-Baker Pain Scale. Statistical analyzes were performed with SPSS software.Results: There was no statistically significant difference in Wong-Baker values(p>0.05). The laser group had more '0' values on days 1 and7; same values as the control group were recorded on other days. In soft tissue healing 3rd day evaluations, non-epithelialized surface of laser socket was found to be smaller than control group, and measurement results were found to be statistically significant(p<0.05). The other days' measurement results were not statistically significant(p>0.05).Conclusions:Although LLLT not found to be very effective in reducing postoperative discomfort after extraction of primary molars, it provides better wound healing in extraction sockets.

This study aimed to evaluate the proliferation and migration of fibroblast cells derived from chronic wounds and investigate the impact of low-level laser therapy (LLLT) on their growth and migration. A total of 60 dermal samples were obtained from three sites of chronic pressure ulcers and diabetic ulcers in 20 patients. Following collection in the operating room, the dermal samples were isolated using the procedure described by Freshney RI. Fibroblasts from the wound base (Site 1) exhibited a slow proliferation rate and a decrease in proliferative capacity. Fibroblasts from wound margins (Site 2) and adjacent healing skin (Site 3) could be successfully isolated and maintained for multiple generations without any morphological changes. Fibroblasts from chronic wounds at Sites 2 and 3 showed slower proliferation rates and reduced migration capabilities compared to normal dermal fibroblasts (control samples). The fibroblast cells were exposed to LLLT at different energy levels (2.5, 3, and 3.5 J/cm2). The laser-treated groups demonstrated a significantly higher increase in cell count compared to the control sample, with the highest increase observed at an energy level of 3 J/cm2. These findings suggest that LLLT at an energy level of 3 J/cm2 could effectively enhance fibroblast migration, indicating its potential as a therapeutic intervention for chronic wounds.

Several Lung diseases can result in lung damage structural changes, with lung transplantation as a only therapeutic option when the disease reaches an advanced progression, unfortunately, the success of lung transplantation is limited. In this context, lung bioengineering is considered a potential therapeutic alternative and the current approach is based on the use of the natural extracellular matrix (ECM) of the decellularized lung. The use of undifferentiated cells to seed an ECM can be a more practical strategy for lung bioengineering but the sterilization of the organ for this recellularization process is still a challenge. In this sense, Low-Level Laser Therapy (LLLT) can emerge as a potential treatment alternative. Therefore, the objective of this study was to verify if LLLT, can optimize lung recelularization with mesenchymal stem cells by cytokine modulation. For this, we decellularized lungs from C57BL/6 mice perfusing SDS 1% via pulmonary artery, sterilized with LLL (660nm, 100mW, 30s). Whole lung scaffolds were recellularized: (1) Recellularized Lung (2) Recellularized Lung + LLLT. Mesenchymal stem cells derived from human tooth pulp (DPSc) were seeded into lungs and incubated for 24 hours at 37ºC, 5% CO₂, in a bioreactor-like conditions, maintaining CPAP at 20cmH2O, 90% O2, and LLL at wavelength of 808nm, 100mW, 30s. Culture medium were analyzed at 24 hours. H&E, immunostaining, SEM and ELISA assay were performed. We produced viable biological scaffolds absent of DNA content, preserving glycosaminoglycans and collagen I, III and IV, fibronectin, laminin and elastin and lung structure (SEM). The levels of IL-6 and IL-8 were stable during the 24 hours of culture. IFN-γ levels showed significant difference in the DPSc and DPSc+LLLT group in the 24-hour evaluation. The levels of IL-10 decreased after LLLT. These findings highlight LLLT's role in cytokine regulation and contamination prevention during lung recellularization with mesenchymal stem cells. Overall, these results demonstrated that LLLT's modulated cytokine levels and could prevent contamination during the lung recellularization process with mesenchymal stem cells, offering promise for enhanced therapeutic strategies in lung bioengineering.

Background: The prevalence of atopic dermatitis in domestic animals is one of the problems of modern veterinary. Treating with standard techniques using chemotherapeutic agents not always leads to a positive result of therapy; moreover, many drugs produce adverse side effects. Methods: Low level laser therapy, in particular, intravenous laser blood illumination (ILBI) has a pronounced and long-lasting impact on the immune system of animals. The combined technique including ILBI-635 (635 nm, 2 mW, 5 min) and LUVBI^® (365 nm, 2 mW, 3 min) every other day provides a positive change in clinical status of cats with allergic dermatitis after the 3rd-4th treatment session. Results: The increased level of erythrocytes and hemoglobin was identified in the course of treatment, and it indirectly indicates increased blood transport activity, which improves trophic provision and microcirculation. A double reduction of leukocytes and a significant decrease of neutrophil cells indicate the immunomodulatory effect of LILI (low-intensity laser illumination). The increase in the percentage of lymphocytes and the decrease of eosinophils and monocytes against the background of basophil concentrations deviations within physiological concentration result in the reduction of inflammatory mediators expression that induce itching. The reduction of total IgE concentration 32 times against control on the 7th day of treatment correlates with the decrease in the quantitative content of peripheral blood eosinophils, indicating the decrease in severity of an allergic process. Conclusion: LLLT is recommended against the background of standard drug therapy to achieve quick clinical outcome together with a long-lasting prolonged effect.

It is well known that the effect of laser irradiation on the blood causes a change in the shape of red blood cells and an increase in their activity, especially in low-level laser therapy (LLLT). The aim of this study was to identify the ability of erythrocytes to deform when exposed to a blue laser.24 laboratory rats were exposed to blue laser in the gingival region of the lower jaw daily for 5 minutes over 3 days. The blue laser possessed a power of 0.5 W and was operated using a con-tactless approach, the dynamic technique in continuous wave mode, and an uninitiated fiber. A blood sample was taken from the lateral vein of the tail before the LLLT, on the first, second, third, and fifth days. The samples were stained, and cytometry was conducted. The exposure to blue laser caused a significant increase in the number of dome-shaped deformable erythrocytes in the blood of laboratory rats (p

Nowadays, the uses of laser and optics in the medical areas are extremely vivid, especially low-level laser therapy. The light with the wavelength of 633 nm to 1200 nm could penetrate and propagate deep in biological tissue. To develop the low-level laser therapy device, optimizing light delivery is critical to accurately stimulate the biological effects inside the biological tissue. Nevertheless, each form of the tissues at each zone on the body had various refractive optic, absorption, scattering, and anisotropy coefficients. This paper describes the simulation results of low-level laser propagation from skin surface at the lower spine, the knee, the femur and the prostate gland with four wavelengths (633 nm, 780 nm, 850 nm, and 940 nm) by the Monte Carlo method. These simulation results are the base for developing the low-level laser therapy device, that could be used in clinical for treating the fracture, knee osteoarthritis, spinal degeneration, and benign prostatic hypertrophy.

The orthodontic treatment brings numerous benefits and, in most cases, the benefits outweigh the possible disadvantages. Root resorption (RR) is a common adverse phenomenon associated with orthodontic treatment. This study evaluates the role of low-level laser emission / Photobiomodu-lation (LE/P) in quantitative measurements of root resorption (QRR). The application of LE/P was done after each orthodontic activation with 4 types of treatment intervention (TI) on the RR after fixed orthodontic treatment (FOT) of the upper arch with ectopic eye tooth/teeth [EET]. 32 Orthodontic patients scheduled for FOT were selected and assigned to the 4 groups. These were LE/P+Self ligating bracket (SLB), LE/P+Conventional bracket (CB), Non-Photobiomodulation (non-LE/P)+SLB, and non-LE/P+CB. Standard management stages of FOT were followed in the maxilla. Each patient received a single application of LE/P labially/buccally and palatally, a total of 5 different points during each activation or appointment. The main outcome measure was QRR in maxillary anteriors before and after FOT assessed via cone-beam computed tomography (CBCT) using 3D OnDemand software. Insignificant QRR was found between before and after FOT in SLB, CLB, and LE/P, non-LE/P groups (p > 0.05). QRR in the SLB vs CB and LE/P vs non-LE/P group was significantly different in 11, 13, and 23 (p < 0.05). QRR in the LE/P+SLB group (p < 0.05) was significantly different in 11, 13, and 23 than that in the other groups. The most severe QRR was found on the 13 (0.88 ± 0.28mm and 0.87±0.27mm) and 23 (1.19 ± 0.14 mm and 1.16±0.13mm) in the CB and non-LE/P group (p < 0.001). LE/P+SLB showed highly significant superior outcome (p < 0.001) in relation to non-LE/P+CB, the QRR of 23 were 0.813± 0.114mm and 1.156± 0.166mm respectively. Significantly higher amount of QRR found in EET patients after FOT treated with the CB, non-LE/P, and non-LE/P+CB system and warrants further investigation to explore potential specific causes.

This Dataset reports the clinical information and measurements of 231 patients who underwent multifrequency low-level laser-assisted mastopexy. The Dataset was collected between February 2021 and November 2023. These data were used to assess the effect of this procedure on breast ptosis degree and the nipple to sternal notch distance to know the evolution of breast ptosis. This article presents demographic, personal and familial history, anthropometric measurements, pto-sis degree according to the Regnault system, Nipple-to-Sternal Notch distance (SNND), and complications according to the Clavien-Dindo System. The collected data were in English, and the responses were anonymised to ensure the Colombian legal framework. The data were stored in a .csv file.

Our hypothesis that controlled ozone applications interfere into the redox balance of the biological organism (first published in 1998 with a preclinical trial on protecting the liver from CCl4 intoxication), has been verified over the last 2 decades in reactive oxygen species (ROS)-induced mitochondrial pathologies, such as rheumatoid arthritis, osteoarthritis, aging processes, diabetes-2 and in prevention of intoxications. Low-dose ozone acts as a redox bioregulator: The restoration of the disturbed redox balance is comprehensible in a number of preclinical and clinical studies by a remarkable increase of the antioxidant repair markers, here mainly shown as glutathione increase and a reduction in oxidative stress markers, mainly malondialdehyde. The mechanism of action is shown, relevant data are displayed, evaluated and comprehensively discussed: The repair side of the equilibrium increases by 21% up to 140% compared to the non-ozone treated groups and depending on the indication; the stress markers are simultaneously reduced, the redox system regains its balance.

This paper deals with a non-contact method to identify the aerodynamic propeller parameters of the Parrot AR.Drone quadrotor. The experimental set consists in a camera recording the vehicle flights, the audio signal is extracted and is used a spectrogram analysis to estimates the propeller velocity. First, the aerial vehicle takes off and starts a hovering maneuver. The experiment is repeated with different additional masses attached to its rigid body. If the weight over the UAV increases/decreases, then the propeller must rotates faster/slower to produce a higher/lower thrust, and consequently, the sound frequency increases/decreases. Finally, this proposition is validated experimentally, and the estimated velocity is used to identify the quadrotor thrust parameters.

Pain is an unpleasant emotional and sensory experience. For many years orthodontists have been looking for an effective method of reducing this feeling of discomfort. In recent years, low-level laser therapy (LLLT) has taken hold in the orthodontic field. Among the countless advantages it can modulate the painful feeling. The aim of this research is to identify the use of photobiomodulation in subjects undergoing fixed orthodontic treatment, to reduce the pain and discomfort that it causes. The research was conducted from the Web of Science, Pubmed and Scopus databases. Only 14 of all articles met the inclusion and exclusion criteria and were therefore used to conduct the research. The different studies compared, in most cases, patients whose mouth was divided into a part treated with laser therapy and a placebo part. The results show a statistically significant difference in perceived pain between the irradiated arch and the non-irradiated arch. Three authors didn’t find statistically significant results in favour of low-laser therapy, but it is important to remember that they used different parameters. To obtain generally valid studies, with consistent and reproducible results, it is necessary to standardize the different parameters used that are independent by operator performing the procedure.

Thermal plasma is a versatile technology that can be used to treat various types of wastes, including vegetal and mineral oils, solvents, plastics, papers and cardboard, glasses, bricks and rocks, metals, clothes, and mixtures of these materials. In this study, we utilized a commercial plasma cutter as a thermal plasma source to decrease the volume of a simulated low-level radioactive mixed solid waste. The simulated waste included papers, plastics, clothes, gloves, metals and stable Co, Cs, Sr, and Ce additives as surrogates of 60Co, 137Cs, 90Sr, and 144Ce, the latter typical contaminants in nuclear LLW. As a result of the process two products were obtained, a solid phase in which we focused this work and a gaseous phase. To retain as much as possible surrogates in the solid final phase, crushed glass from broken bottles was included as a vitrification additive to the original waste. After undergoing heat treatment, a dense vitreous slag was produced and ashes. The process resulted in a volume reduction of 70%, indicating the successful gasification of organic excess materials. The surrogate elements were retained in the process and were found in the ashes composition: Co (3.4% w/w), Cs (37.7% w/w), Ce (0.6% w/w) and in the glass matrix composition of Co, Cs, Sr and Ce: 72.4 ± 14.7, 32 ± 18.2, 125.3 ± 31.6, 80 ± 13.1 % w/w respectively. For the actual experimental conditions, retention efficiencies were estimated for Cobalt (Co) at 72.4 ± 14.7%, Cerium (Ce) at 80 ± 13.1%, Strontium (Sr) at 125.3 ± 31.6%, and notably Cesium (Cs) at 32 ± 18.2%.

Due to an increase in the number of image achieves, Content-Based Image Retrieval (CBIR) has gained attention for research community of computer vision. The image visual contents are represented in a feature space in the form of numerical values that is considered as a feature vector of image. Images belonging to different classes may contain the common visuals and shapes that can result in the closeness of computed feature space of two different images belonging to separate classes. Due to this reason, feature extraction and image representation is selected with appropriate features as it directly affects the performance of image retrieval system. The commonly used visual features are image spatial layout, color, texture and shape. Image feature space is combined to achieve the discriminating ability that is not possible to achieve when the features are used separately. Due to this reason, in this paper, we aim to explore the low-level feature combination that are based on color and shape features. We selected color moments and color histogram to represent color while shape is represented by using invariant moments. We selected this combination, as these features are reported intuitive, compact and robust for image representation. We evaluated the performance of our proposed research by using the Corel, Coil and Ground Truth (GT) image datasets. We evaluated the proposed low-level feature fusion by calculating the precision, recall and time required for feature extraction. The precision, recall and feature extraction values obtained from the proposed low-level feature fusion outperforms the existing research of CBIR.

Objective: We report a case of acute pancytopenia and liver injury after concomitant administration of low-dose methotrexate (MTX), and high-dose esomeprazole and metamizole. Case summary: A 71-year-old patient with chronic systemic idiopathic erosive arthritis was admitted after a pelvic ring fracture. After hospital admission, she received MTX in addition to esomeprazole and metamizole. Subsequent laboratory tests revealed pancytopenia and elevated liver enzymes. The follow-up clinical examinations were unremarkable, with the exception of sub-febrile temperatures. Further investigations did not detect a definitive etiology. Due to the suspicion of methotrexate-induced hematotoxicity and hepatotoxicity, antagonizing therapy with calcium folinate was administered, after which the blood counts and liver parameters normalized. Discussion: Due to the administration of high-dose metamizole immediately before the administration of low-dose MTX, the pre-existing hematotoxic pharmacodynamic effect of MTX was acutely enhanced by that of metamizole, although folic acid was administered preemptively. In addition, the concomitant administration of high-dose esomeprazole and normal dose torasemide resulted in a pharmacokinetic interaction with MTX by decreasing its renal secretion and elimination, further enhancing the concentration-dependent hematotoxic and hepatotoxic side effects of MTX. Conclusions: The relatively high demand for analgesics in patients with chronic rheumatic diseases already being treated with MTX and proton pump inhibitors necessitates that clinicians consider drug-drug interactions as potential causes of adverse drug reactions after the administration of metamizole or nonsteroidal anti-inflammatory drugs. In this category of patients, it is strongly recommended to switch to analgesics of other classes.

A millimeter-wave microstrip leaky-wave antenna array based on the substrate-integrated waveguide (SIW) and the complementary split-ring resonator (CSRR) is proposed in this paper. The slow wave characteristics of the SIW are enhanced by etching two rows of symmetrical CSRR-type slots on the surface of the SIW layer. The magnetic coupling between the CSRR-SIW layer and equally spaced circular patches array on the upper layer realizes the radiation of electromagnetic energy. In the 23~30 GHz (relative bandwidth 26.4%) operating frequency band, the horizontal polarization radiation beam scanning from -62° to -2° is realized, with a peak gain of 9.6~11.7 dBi, and the cross-polarization ratio is more than 43.8 dB.

Fluorescence microscopy is an important tool for disease diagnosis, often requiring costly optical components, such as fluorescence filter cubes and high-power light sources. Due to its high cost, conventional fluorescence microscopy cannot be fully exploited in low-income settings. Smartphone-based fluorescence microscopy becomes an interesting low-cost alternative, but raises challenges in the optical system. We present the development of a low-cost inverted laser fluorescence microscope, that uses a smartphone to visualize the fluorescence image of biological samples. Our fluorescence microscope uses a laser-based simplified optical filter system, that provides analog optical filtering capabilities of a fluorescence filter cube. Firstly, we validated our inverted optical filtering by visualizing microbeads labeled with three different fluorescent compounds or fluorophores, commonly used for disease diagnosis. Secondly, we validated the disease diagnosis capabilities, by comparing the results of our device with those of a commercial fluorescence microscope. We successfully detected and visualized Trypanosoma cruzi parasites, responsible of the Chagas infectious disease, and the presence of Antineutrophil cytoplasmic antibodies of the ANCA non-communicable autoimmune disease. The samples were labeled with the fluorescein isothiocyanate (FITC) fluorophore, one of the most commonly used for disease diagnosis. Our device provides a 400 X magnification and is at least two orders magnitude cheaper than conventional commercial fluorescence microscopes.

This paper investigates the use of contactless power ultrasonic excitation to decrease the electrical impedance of the weld in laser welding. The literature extensively documents the impact of em-ploying contact power ultrasonic excitation on the microstructure morphology and refinement of grain in the weld. This study involves characterizing an industrial High Power Ultrasound Transducer (HPUT) by determining the optimal distance and angle for contactless excitation of the fusion zone in the weld, aiming to achieve the maximum amplitude. Subsequently, the transducer is integrated into the laser welding system, resulting in the creation of an ultrasonic-assisted welding system. To find the improvement due to the contactless vibration assistance, the welding area was char-acterised by an impedance ohmmeter device. The results indicate an approximately 6 % im-provement in the welding quality in terms of the impedance value, an important parameter for battery pack welding. In response to the issue of overheating in the industrial transducer during prolonged welding operations, an alternative transducer was proposed to overcome this challenge. Further investigations are carried out by the alternative transducer to find the effect of different wave types, namely, shear and compressional waves, on the welding quality. The contact vibration can excite the plate approximately 50 times higher in acceleration amplitude than contactless ex-citation. Nevertheless, enhancements of 10% and 6% are observed in the impedance value when utilising compressional and shear waves, respectively, as compared to the results obtained with contactless vibration.

Optimum design and accurate control of the internal structure of the laser target materials remain an important goal for various laser physics experiments, especially for generating high flux photon and neutron beams. The low-density material is considered to be one of the most difficult for X-ray study due to its high transparency and imperceptible contrast. To produce clear visualization of foam containing sparse structures we used a high-quality monochromatic X-ray beam of synchrotron radiation source PETRA-III at DESY. The X-ray beam parameters allow tomographic scanning with application of phase contrast retrieval algorithms. A series of 3D images of foam-suspended glass microsphere inside the plastic cylinder were obtained with the quality high enough to observe the internal structure and to visualize uniformity, displacement and surface roughness on both sides of the microsphere. The main object under investigation was a CH-plastic capillary including 10 mg/cc CHO-foam with the centered glass microsphere. The results of this work demonstrate that tomographic visualization based on a high quality X-ray radiation and phase contrast analysis is an effective and useful technique for development of new laser targets containing structured low density materials.

An ultra-low anti-reflection optical coating on both surfaces of a plastic cover slip was studied for use in confocal image measurement. The optical reflectance at a wavelength of 632.8 nm was less than 0.1% when the coated sample was placed in a liquid having a refractive index of 1.34 close to the aqueous solution of the biomaterial. The high- and low-index coating films, Substance-2 (PrTiO3) and silicon dioxide (SiO2), were measured by an ellipsometer to determine their optical refraction indices and extinction coefficients. Theoretically, when the two layer thicknesses are designed using the optical admittance diagram of the cover slip to approach the equivalent index of 1.34, a reflectance of 1.6×10-5% in the liquid could be obtained. Experimentally, the reflectance of the sample deposited on the two faces of the cover slip was 4.223±0.145% as measured in the air; and 0.050±0.002% as measured by a He-Ne laser in the liquid.

One of the measures required by the European Green Deal to decarbonise the freight transport sector is the promotion of inland waterway transport (IWT), in particular intermodal transport in Europe. To facilitate intermodal transport on the Danube, we developed six new barge designs for the transport of 45' pallet-wide high-cube containers using a four-step approach. Our approach consisted of detailed desk research, followed by design and further analysis of the identified barge types, taking into account, for example, sight lines or stability. The container carrying capacity reaches up to 90 containers in three layers, which is double the capacity of existing standard barges on the Danube. Nevertheless, three-layer transport is hardly feasible in several cases, due to restrictions regarding sight lines and stability. We conclude that each loading condition must be evaluated separately to determine the best barge design option for each case. The study is limited by its geographical scope and the type of container used to develop the new barge designs. This could be a possible direction for further research on this topic: using other container types and/or extending the geographical scope.

This study evaluates the agricultural carbon emission efficiency of Shandong Province from 2011 to 2020 using the DEA-SBM model. The nexus between endogenous and exogenous variables is estimated using the Tobit model. The findings reveal an overall increasing trend in agricultural carbon emissions, with significant variations in efficiency values among different cities, leading to a severe polarization. Spatial evaluation shows a high distribution trend in the central region and low in the eastern and western regions of Shandong Province. The empirical tests conducted for Shandong Province and its three regions indicate that urbanization plays a major role in sup-porting the growth of agricultural carbon emission efficiency, while the education level of the la-bor force has a suppressive impact. Economic development and crop cultivation structure, how-ever, have no significant influence. The impact of these variables varies across the eastern, central, and western regions. The proposed countermeasures include improving planting structure and reducing brain drain in the eastern region, strengthening agricultural and rural inputs and in-creasing the added value of agricultural products in the central region, and intensifying the link-age between urbanization and industrial layout in the western region to reduce agricultural car-bon emissions efficiency in Shandong Province.

Low back pain (LBP) is a leading cause of disability. It significantly impacts the patient’s quality of life, limits their daily living activities, and reduces work productivity. To reduce the burden of LBP, several pharmacological and non-pharmacological treatment options are available. This review summarizes the role of heat therapy in the management of LBP. First, we outline the common causes of LBP, then discuss the general mechanisms of heat therapy on (LB)P, and finally review the published evidence regarding the impact of heat therapy in patients with acute or chronic non-specific LBP. This review demonstrates that continuous, low-level heat therapy provides pain relief, improves muscular strength, and increases flexibility. Therefore, this effective, safe, easy-to-use, and cost-effective non-pharmacological pain relief option is still relevant in modern clinical practice.

Interaction of an electromagnetic field with matter in a laser cavity without the assumption of a fixed direction of the transverse electric field, described by the two-level Maxwell-Bloch equations, is studied. By using a perturbative nonlinear analysis, performed near the laser threshold, we report on the derivation of the laser (3+1)D vectorial complex cubic-quintic complex Ginzburg-Landau equation. Furthermore, we study the modulational instability of the plane waves both theoretically using the linear stability analysis, and numerically, using direct simulations via the split-step Fourier method. The linear theory predicts instability for any amplitude of the primary waves. Our numerical simulations confirm the theoretical predictions of the linear theory as well as the threshold of the amplitude of perturbations. The system understudy shows a deep dependence on the laser cavity parameters, for which there appear wave patterns in accordance with the predictions from the gain spectrum.

Abstract: High power semiconductor laser is a kind of photoelectric device with high efficiency and high stability, the performance of its drive system directly affects its output characteristics and service life. In order to solve the problems of stability and robustness of the output power of semiconductor laser, a semiconductor laser driving power supply with high efficiency, low ripple and strong anti-interference ability was developed. The power supply adopts full-bridge LCC resonant power topology. Firstly, a mathematical model is established to analyze the relationship between LCC resonator parameters and output current gain. Secondly, a LCC resonator parameter design method is proposed to reduce the current stress of components, and the variable frequency phase shift (PFM-PWM) composite control strategy and linear active disturbance rejection control (LADRC) algorithm are proposed, which not only ensures the zero voltage (ZVS) conduction of MOS tube, but also reduces the on-off loss of MOS tube. Improved power efficiency and suppressed output current ripple; At the same time, the instability of the output current is ensured due to the input voltage, load and parasitic parameter change of the circuit. Finally, the simulation and experimental results show that the power supply can be continuously adjustable in the output current range of 0-40A, the current ripple is less than 0.8%, and the working efficiency is up to 92%. It has the characteristics of high stability, small ripple, high efficiency, low cost and good robustness.

Background: Chronic non-specific low back pain (CNSLBP) is defined as back pain that lasts longer than 12 weeks. Objectives: To investigate the efficacy of manual therapy (MT) program combined with Capacitive and Resistive Electric Transfer (TECAR) therapy in individuals with CNSLBP. Method: Sixty adults with CNSLBP were randomly equally divided into three groups. The first group followed an MT protocol in the lumbar region (MT group), the second group followed the same MT protocol combined with TECAR therapy (MT + TECAR group) using a conventional capacitive electrode as well as a special resistive electrode bracelet and the third group (Control group) received no treatment. Both intervention programs included six treatments over two weeks. Pain in the last 24 hours with the Numeric Pain Rating Scale (NPRS), functional ability with the Roland-Morris Disability Questionnaire (RMDQ), Pressure Pain Threshold (PPT) in the lumbar region with pressure algometry, and mobility of the lumbo-pelvic region through fingertip-to-floor distance (FFD) test were evaluated before and after the intervention period with a one-month follow-up. Analysis of variance with repeated measures was applied. Results: In the NPRS score, both intervention groups showed statistically significant differences compared to the control group both in the second week as well as in the one-month follow-up (p < .001). Between-groups differences were also noticed between the two intervention groups in the second week (p < .05). Differences in the RMDQ score in the second week and on the one-month follow-up were detected between the intervention groups and the control group (p < .001), while differences between the two intervention groups were only detected in the one-month follow-up (p < .001). Regarding the PPT values, differences were found mainly between the MT + TECAR and the control group and between the MT + TECAR and the MT group (p < .05), with the MT + TECAR group in most cases showing the greatest improvement compared to the other two groups, which remained statistically significant in the one-month follow-up (p < .05). Finally, both intervention groups improved the mobility of the lumbo-pelvic region in both time points compared to the control group without, however, statistically significant differences between them (p> .05). Conclusion: The application of an MT protocol with TECAR therapy appeared more effective than conventional MT as well as compared to the control group in reducing pain and disability and improving PPT in individuals with CNSLBP. No further improvement was noted in mobility of the lumbo-pelvic region by adding TECAR to the MT intervention.

In this work, a systematic study was conducted on the fabrication of multi-material components obtained employing Laser-Powder Bed Fusion (L-PBF) technology. The idea of making multi-material components is a winning capability of additive technologies because it allows the fabrication of Functionally Graded Materials (FGMs) with the customization of parts according to different required properties. The transition from one material to another was achieved gradually and continuously within the same layer using ad-hoc equipment designed for L-PBF systems with a powder spreading technique based on coaters or rollers. The influence of the relative position of the different materials within the powder chamber and the geometry of the developed equipment on the metallurgical and mechanical properties of the manufactured samples was evaluated. The performed tests involved the use of two materials, a nickel-based superalloy, and a stainless steel, having different chemical, physical and mechanical properties to obtain gradual properties variation in the manufactured samples. Based on the results of post-process characterization obtained through metallographic, chemical, and mechanical analysis, the relative positions of the materials and the geometry of the developed equipment have a limited effect on the sample’s manufactured properties. The characteristics of the FGM zone depend on the nature of the employed powders, and its extent coincides with that defined during the design of the divider.

Knowledge of the temperature evolution is crucial to understand and control laser beam welding of low-melting materials. Existing temperature determination approaches are restricted to i) one-dimensional temperature information (e.g. ratio-pyrometers), ii) a priori knowledge of the emissivity (e.g. thermography) and iii) high temperature regions (e.g. two-wavelength imaging). In this paper, a ratio-based two-color-thermography approach is developed that allows for two-dimensional temperature determination in low-melting temperature ranges (< 1200 K). For static measurement situations it is demonstrated, that temperature can be determined despite variation in signal intensity and emissivity with high accuracy. The two-color-thermography set-up is further transferred into a commercial laser beam welding machine and experiments are conducted for varying process parameters. The direct application of the developed two-color-thermography system in dynamic process situations is limited as image artifacts presumably caused by internal reflections inside the optical beam path are present.

This study leverages the relationships between the Great Plains low-level jet (GP-LLJ) and the circumglobal teleconnection (CGT) to enhance the 30-day rainfall forecast skill in the Northern Great Plains (NGP). The assessment of 30-day simulated precipitation using the Climate Forecast System (CFS) is contrasted with the North American Regional Reanalysis, searching for sources of precipitation predictability associated with extended wet and drought events. We analyze the 30-day sources of precipitation predictability using (1) the characterization of dominant statistical modes of variability of 900-mb winds associated with the GP-LLJ, (2) the large-scale atmospheric patterns based on 200-mb geopotential height (HGT), and (3) the use of GP-LLJ and CGT conditional probability distributions using a continuous correlation threshold approach to identify when and where the forecast of NGP precipitation occurs. Two factors contributing to the predictability of precipitation in the NGP are documented. We found that multi-scale geospatial interactions occur at the daily and sub-seasonal time windows. The CFS reforecast suggests that the ability to forecast sub-seasonal precipitation increases in response to the enhanced simulation of the GP-LLJ and CGT. Finally, the multi-dimensional analysis of covariance reveals that high-precipitation forecasting skill is associated with a better prognostic of GP-LLJ and CGT.

Accurate measurement of low-level thoron gas and high-accuracy calibration of thoron measurement devices are essential for assessing and preventing thoron radiological risks. This study aimed to develop a thoron gas measurement technique using an airflow-through scintillation cell for both low-level measurement and high-accuracy calibration. To achieve this, a compartment model was developed to estimate the influence of progeny deposition and accumulation on the wall of the scintillation cell to prevent overestimation of thoron. A self-developed scintillation cell was utilized to implement and validate this technique. The lower detection limit and measurement uncertainty were then evaluated to assess the feasibility of the technique for low-level measurement and high-accuracy calibration. The results showed that the compartment model effectively addressed the influence of the progeny deposition. The measurement technique achieved a lower detection limit below 100 Bq m-3 even with the coexistence of 100 Bq m-3 of radon and attained a measurement uncertainty (k = 2) below 10% when the concentration of thoron exceeded 1,000 Bq m-3. In summary, this study developed a reliable and practical thoron gas measurement technique using an airflow-through scintillation cell with consideration for progeny deposition, and is expected to contribute to the assessment and prevention of thoron radiological risk.

The trafficking of illegal drugs by criminal networks at borders, harbors, or airports is an increasing issue in public health as these routes ensure the main supply of illegal drugs. The prevention of drug smuggling, including the installation of scanners and other analytical devices to detect ultra-small traces of drugs within a reasonable time frame, remains a challenge. The presented immunosensor is based on a monolithic affinity column with a large excess of immobilized hapten, which traps fluorescently labeled antibodies as long as the analyte cocaine is absent. In the presence of the drug, some binding sites of the antibody will be blocked, which leads to an immediate breakthrough of the labeled protein, detectable by highly sensitive laser-induced fluorescence with the help of a Peltier-cooled complementary metal-oxide-semiconductor (CMOS) camera. Liquid handling is performed with high-precision syringe pumps and microfluidic chip-based mixing devices and flow cells. The biosensor achieved limits of detection of 23 pM (7 ppt) of cocaine with a response time of 90 seconds and a total assay time below 3 minutes. With surface wipe sampling, the biosensor was able to detect 300 pg of cocaine. This immunosensor belongs to the most sensitive and fastest detectors for cocaine and offers near-continuous analyte measurement.

This study investigated the roles of low-molecular-weight fucoidan (LMWF) in enhancing the anti-cancer effects of fluoropyrimidine-based chemotherapy. HCT116 and Caco-2 cells were treated with LMWF and 5-FU. Cell viability, cell cycle, apoptosis, and migration were analyzed in both cell types. Potential mechanisms underlying how LMWF enhances the anti-cancer effects of fluoropyrimidine-based chemotherapy were also explored. The cell viability of HCT116 and Caco-2 cells was significantly reduced after treatment with a LMWF-5-FU combination. In HCT116 cells, LMWF enhanced the suppressive effects of 5-FU on cell viability through the 1) induction of cell cycle arrest in the S phase and 2) late apoptosis mediated by the Jun-N-terminal kinase (JNK) signaling pathway. In Caco-2 cells, LMWF enhanced the suppressive effects of 5-FU on cell viability through both c-mesenchymal–epithelial transition (MET)/ Kirsten Rat Sarcoma virus (KRAS)/ extracellular signal-regulated kinase (ERK) and c-MET/ phosphatidyl-inositol 3-kinases (PI3K)/ protein kinase B (AKT) signaling pathways. Moreover, LMWF enhanced the suppressive effects of 5-FU on tumor cell migration through the c-MET/ matrix metalloproteinase (MMP)-2 signaling pathway in both HCT116 and Caco-2 cells. Our results demonstrated that LMWF is a potential complementary therapy for enhancing the efficacies of fluoropyrimidine-based chemotherapy in colorectal cancers (CRCs) with the wild-type or mutated KRAS gene through different mechanisms. However, in vivo studies and in clinical trials are required to validate the results of the present study.

This article presents results of the polarization laser studies of the optical and microphysical characteristics of the high-level clouds (HLC). The high-altitude matrix polarization lidar (HAMPL; Tomsk, Russia) is described. HAMPL measures vertical profiles of all elements of the backscattering phase matrix (BSPM) of the HLC. Based on the joint analysis of lidar and radiosonde observations it is shown that the spatial structure of the HLC containing oriented ice crystals is inhomogeneous in the horizontal wind direction. It includes local areas with oriented particles; the sizes of such areas are estimated together with the most probable meteorological conditions of their formation. The shortcomings of the radiosonde observations performed closest to the location of the HAMPL are described. The applicability of the ERA5 reanalysis data of the European Centre for Medium-Range Weather Forecasts for use as an alternative source of information on the vertical profiles of meteorological quantities for the interpretation of HLC lidar sensing data in Western Siberia was checked.

This paper presents a device for measuring and maintaining the constant water level in a tank. The device uses a capacity sensor to measure the water level. The sensor has a DC voltage output proportional to the water level in the tank. This voltage can be used in other automation too. The water level, in percentages, is displayed on a vu meter with 8 LEDs. The circuit for maintaining the constant level consists in a comparator with hysteresis. The level of the water is adjustable, using a reference voltage from a potentiometer (marked in percentages). The level of the water is compared with the prescribed level and the difference between them commands the start/stop of the water pump which supplies the tank through a relay. The device is powered by 220 V and is isolated from the environment.

Low back pain (LBP) is a pandemic and costly musculoskeletal condition in the United States. Patients with LBP may endure surgery, injections, and expensive visits to emergency departments. Some suggest that using physical therapy or chiropractic in the earlier stage of LBP reduces the utilization of expensive health services and lowers the treatment costs. Nevertheless, there is no consistent evidence to declare which one of these methods is a cost-effective treatment within a short (less than a year) period of time. The purpose of this study was to investigate the cost-effectiveness of chiropractic versus physical therapy in the United States. A decision tree analytic model was used for estimating the economic outcomes. The findings showed that in the chiropractic group, the total average cost was $48.56 lower than the physical therapy group, and daily adjusted life years (DALY) was 0.0043 higher than the physical therapy group. Chiropractic care was shown to be a cost-effective alternative compared with physical therapy for adults with at least three weeks of low back pain over six months.

Growing incidence of myopia worldwide justifies the search for efficient methods of myopia prevention. Numerous pharmacological, optical, and lifestyle measures have already been utilized, but there remains a need to explore more practical and predictable methods for myopia control. This paper presents a review of the latest literature on preventing the progression of myopia using Defocus Incorporated Multiple Segments Spectacle Lenses (DIMSsl), Repeated Low-level Red-Light Therapy (RLRL), and the combination of low-dose atropine (0.01%) with orthokeratology lenses.

The transmission and analysis of data is one of the challenges of the 21st century. In the field of environmental measurement technology, existing broadband and wireless technologies have not been able to transmit data reliably and cost-effectively over long distances and in hard-to-reach places. LoRaWAN, an IoT technology, could be an energy-efficient, cost-effective and secure alternative as a narrowband technology in combination with battery-powered sensors and thus make an important contribution to the intelligent, largely wireless networking of objects, plants and machines (IoT), for example in the municipal sector. In addition to ecological and economic benefits, the quality of life in modern, intelligently networked cities can be enhanced by real time data acquisition. However, the prerequisite is that the quality of the data acquired via this method is sufficiently good. This paper therefore addresses the question of the quality of particulate matter data collected by low-cost sensors. To determine this, an SDS011 particulate matter sensor from Nova Fitness was ported to LoRaWAN. The sensor was installed next to a governmental measurement station. In a test that lasted five weeks, data from the SDS011 sensor were compared with those from the governmental station. Differences were identified and a correction approach was developed and applied. The efficiency of the approach was verified. Based on the results, it can be seen that the use of the low cost sensors has weaknesses. Problems can only be partially reduced. Nevertheless, the use of the low-cost sensors can be helpful for a flexible and cost effective collection of environmental data.

Mortality in children accounts for 15% of all AIDS-related deaths globally, with a higher burden among Cameroonian children (25%), likely due to poor virological response. We sought to evaluate viral suppression (VS) and its determinants in a nationally representative paediatric and young adult population receiving antiretroviral therapy (ART). A cross-sectional and multicentric study was conducted among Cameroonian children (

This study aimed to evaluate the early-childhood comorbidities of cerebral palsy (CP) in children with low birth weight (LBW) and assess the impact of maternal bio-psychosocial factors on the risk of CP in preterm infants across varying birth weights. Data for 15,181 prematurely born infants from 2009 to 2013 and 151,810 matched controls from Taiwan's National Health Insurance Research Database were analyzed. Period prevalence of CP, and comorbidities of LBW were verified, and odds ratios (ORs) were calculated. Results confirmed that increasing prematurity and low birth weight (LBW) rates in Taiwan. LBW was associated with higher CP prevalence. Maternal age extremes (&lt;20 and &gt;40 years) were significant risk factors of CP in LBW infants. LBW infants showed higher risks of respiratory, circulatory, and nervous system and psycho-developmental comorbidities compared to controls. Infants with the lowest birth weights had even higher ORs for these comorbidities. However, gastrointestinal and nutritional comorbidities were less prevalent in premature infants. Maternal factors such as family income, number of hospital admissions, and length of hospital stay were significantly correlated with birth weight and subsequent complications. Each additional gestational week significantly reduced the risk of complications in premature infants. Additionally, maternal bio-psychosocial factors were associated with birth weight and related outcomes in premature infants, emphasizing the importance of addressing these factors in prenatal care and interventions.

This paper investigates if the polar groups induced by a plasma treatment can increase the lap shear strength of laser joined metal and plastic hybrids. Optimal laser joining parameters for cold-rolled AISI304 – Polyamide 6.6 and sandblasted AISI304 - Polypropylene hybrids are developed. The OWRK-method was utilized to identify the change in surface free energy of a low-pressure plasma treatment. Plasma treated samples were joined and tested. The fractured surfaces were investigated via light microscopy and SEM. The arithmetic means of the plasma treated hybrids lap shear strength with polyamide 6.6 varied slightly but all measured values were within the range of the untreated samples. The lap shear strengths of the polypropylene hybrids were significantly reduced. This was attributed to an overaging and the development of low molecular weight oxidized materials which lead to a weak boundary layer. No correlation between surface free energy and the lap shear strength could be found.

Level index was introduced in 2017 for rooted trees which is a component of Gini index. In the origin, Gini index is a tool for economical investigations but Balaji and Mahmoud defined the graph theoretical applications of this index for statistical analysis of graphs. Level index is an important component of Gini index. In this paper we define a new graph polynomial which is called level polynomial and calculate the level polynomial of some classes of trees. We obtain some interesting relations between the level polynomials and some integer sequences.

Obesity and overweight are associated with many metabolic diseases, such as hypertension, diabetes, and dyslipidemia, which are closely related to a sedentary lifestyle and lack of exercise. Aerobic exercise effectively increases the high-density lipoproteins-cholesterol (HDL-C) levels and decreases the triglyceride (TG) levels. The consumption of Cuban policosanol (Raydel®) is also effective in enhancing the HDL-C quantity and HDL functionality to treat dyslipidemia and hypertension. On the other hand, no study has examined the effects of a combination of high-intensity exercise and policosanol consumption in obese subjects to improve metabolic disorders. In the current study, 17 obese subjects (average BMI 30.0±1.1 kg/m2, eight male and nine female) were recruited to participate in a program combining exercise and policosanol (20 mg) consumption for 12 weeks. After completion, their BMI, waist circumference, total fat mass, systolic blood pressure (SBP), and diastolic blood pressure (DBP) decreased by approximately 15% (p=0.022), 12.7% (p=0.008), 33% (p=0.006), 11% (p<0.046), and 13% (p=0.007), respectively. In the serum lipid profile, at week 12, they showed a remarkable decrease in the total cholesterol (TC) and triglyceride (TG) levels, up to 17% (p<0.019) and 54% (p<0.002) from the baseline, respectively. Although the serum HDL-C was increased by approximately +12% from the baseline, the percentage of HDL-C in TC, HDL-C/TC (%), was increased by up to +32% (p=0.007) at week 12. The serum coenzyme Q10 (CoQ10) level was increased 1.2-fold in all participants at week 12 from the baseline. In particular, the male participants showed a 1.4-fold increase (p=0.027) from the baseline. The larger increase in serum CoQ10 was correlated with the larger increase in the serum HDL-C during 12 weeks. The hepatic function parameters were improved; the serum -glutamyl transferase decreased at week 12 by up to 55% (p<0.007), while the aspartate aminotransferase and alanine transaminase levels decreased within the normal range. In the lipoprotein level, the extent of oxidation and glycation were reduced significantly in VLDL and LDL, with a remarkable decrease in the TG content in particles. The antioxidant abilities of HDL2 and HDL3, such as paraoxonase (PON) and ferric ion reduction ability (FRA), were enhanced significantly by up to 1.8-fold (p<0.001) and 1.6-fold (p<0.001) at week 12. The particle size and number of HDL2 were increased up to +10% during the 12 weeks with a remarkable decrease in the TG content, glycation extent, oxidation up to 32% (p=0.032), 18% (p=0.043), and 11% (p=0.023), respectively. The particle number and diameter of HDL3 were increased by up to +9% with a remarkable increase in the PON activity, FRA activity, and TC content of +82% (p<0.001), +56% (p<0.001), and +32% (p=0.009), respectively. Expression of apolipoproteinA-I in HDL2 and HDL3 were significantly elevated more in both gender around 30~48% with more distinct band intensity and less glycation at week 12. These improvements in HDL quality and functionality were linked to the higher survivability of adult zebrafish and their embryos. Under the co-presence of carboxymethyllysine (CML), a microinjection of HDL2 to zebrafish embryo from week 0 resulted in approximately 47% survivability with developmental defects and attenuated speed. On the other hand, the HDL2 microinjection from week 12 resulted in remarkably higher survivability (~ 70%). In conclusion, 12 weeks of Cuban policosanol (Raydel®, 20 mg) consumption with high-intensity exercise showed significant improvement in blood pressure, body fat mass, blood lipid profile without liver damage, CoQ10 metabolism, and renal impairment. At week 12, all participants showed a remarkable decrease in oxidation and glycation extent in the VLDL and LDL with a decrease in the TC and TG content. Significant enhancement of the qualities and functionalities in HDL2 and HDL3 by the policosanol consumption were also detected: increase in apoA-I content, TC content, particle size, and particle numbers along with antioxidant abilities, such as PON and FRA.

Purpose: to assess any differences on marginal bone loss between bone-level or tissue-level dental implants through a review of literature until September 2019. Materials and methods: MEDLINE, Embase and other database were searched by two independent authors. The search was limited to articles in English. Results: The search provided 1028 records and, after removing the duplicates through titles and abstracts screening, 45 full-text articles were assessed for eligibility. For qualitative analysis 20 articles were included, 17 articles of them for quantitative analysis. A total of 1161 patients (mean age 54,4 years) and 2933 implants were observed, 1427 (Tissue-level) and 1506 (Bone-level). The survival rate and the success rate were more than 90%, except for 2 studies with a success rate of 88% and 86.2%. No studies reported any differences between groups in term of success and survival rates. Three studies showed that BL-implants had statistically less marginal bone loss (P< 0.05). Only one study reported statistically less marginal bone loss in TL-implants (P< 0.05). In the most part of the studies, differences between implant types in marginal bone loss were not statistically significant. Conclusion: Despite to the peri-implant tissue around transmucosal implants has been reported to be inflammation-free because of the absence of bacterial infiltration in the micro-gap between the fixture and abutment, no clinical and radiological differences were highlighted between groups from the included studies after a variable period of follow-up ranged between 1 to 5 years.

Portugal Mainland has hundreds of thousands of people living in the Atlantic coastal zone, with numerous high economic value activities and a high number of infrastructures that must be protected from natural coastal hazard, namely extreme storms and sea level rise (SLR). In the context of climate change adaptation strategies, a reliable and accurate assessment of the physical vulnerability to SLR is crucial. This study is a contribution to the implementation of flooding standards imposed by the European Directive 2007/60/EC, which requires each member state to assess the risk associated to SLR and floods caused by extreme events. Therefore, coastal hazard in the Continental Atlantic coast of Portugal Mainland was evaluated for 2025, 2050 and 2100 in the whole coastal extension with different sea level scenarios for different extreme event return periods and due to SLR. A coastal flooding probabilistic map was produced based on the developed methodology using Geographic Information Systems (GIS) technology. The Extreme Flood Hazard Index (EFHI) was determined on flood probabilistic bases through five probability intervals of 20% of amplitude. For a given SLR scenario, the EFHI is expressed, on the probabilistic flooding maps for an extreme tidal maximum level, by five hazard classes ranging from 1 (Very Low) to 5 (Extreme).

Many reported sea level records are often not a single measurement. They are then a composition of different records from several tide gauges. Sometimes, they are from the same tide gauge, but the tide gauge stability has been affected by earthquakes. This is the case of Guam as discussed in the present manuscript. The claimed sea level acceleration of Guam is only the result of two earthquakes that have compromised the stability of the tide gauge.

Data collected at the Cascais tide gauge, located on the west coast of Portugal Mainland, have been analyzed and sea level rise rates have been updated. Based on a bootstrapping linear regression model and on polynomial adjustments, time series are used to calculate different empirical projections for the 21^st century sea level rise, by estimating the initial velocity and its corresponding acceleration. The results are consistent to an accelerated sea level rise, showing evidence of a faster rise than previous century estimates. Based on different numerical methods of second order polynomial fitting, it is possible to build a set of projection models of relative sea level rise. Appling the same methods to regional sea level anomaly from satellite altimetry, additional projections are also built with good consistency. Both data sets, tide gauge and satellite altimetry data, enabled the development of an ensemble of projection models. The relative sea level rise projections are crucial for national coastal planning and management since extreme sea level scenarios can potentially cause erosion and flooding. Based on absolute vertical velocities obtained by integrating global sea level models, neo-tectonic studies and permanent Global Positioning System (GPS) station time series, it is possible to transform relative into absolute sea level rise scenarios, and vice-versa, allowing the generation of absolute sea level rise projection curves and its comparison with already established global projections. The sea level rise observed at the Cascais tide gauge has always shown a significant correlation with global sea level rise observations, evidencing relatively low rates of composed vertical land velocity from tectonic and post-glacial isostatic adjustment, and residual synoptic regional dynamic effects rather than a trend. An ensemble of sea level projection models for the 21st century is proposed with its corresponding probability density function, both for relative and absolute sea level rise for the west coast of Portugal Mainland.

Aim: The purpose of this study is to evaluate the remineralization potential of primary teeth enamel after being exposed to different laser diode therapy. Methods: Ninety-six vestibular primary teeth enamel samples were divided into eight groups (n=12) with varying treatments: control (G1), CPP-ACP-fluoride varnish (G2), diode lasers at 980 nm (G3), 808 nm (G4), 450 nm (G5), 980 nm + CPP-ACP-fluoride varnish (G6), 808 nm + CPP-ACP-fluoride varnish (G7), and 450 nm + CPP-ACP-fluoride varnish (G8). Each sample was assessed using DIAGNOdent® at baseline, post-treatment, and post-pH cycle re-mineralization. SEM imaging was performed before and after treatment and following the pH cycle. Results: The results indicated that the 980 nm and 808 nm diode lasers, both alone and in combination with CPP-ACP-fluoride varnish, either maintained or increased the calcium (Ca) weight percentage (Wt%) in the enamel. The 980 nm diode laser combined with CPP-ACP-fluoride varnish (G6) showed a significant increase in Ca Wt%, suggesting a strong remineralization effect. Similarly, the 808 nm diode laser alone (G4) also promoted a substantial increase in Ca Wt%. In contrast, the 450 nm diode laser, whether applied alone or in combination with CPP-ACP-fluoride varnish, resulted in a lower Ca Wt% and an increase in phosphorus (P) Wt%. Most groups, except for the CPP-ACP-fluoride varnish alone (G2), demonstrated an increase in P Wt%, indicating a complex interaction between laser therapy and enamel remineralization. Conclusions: The combined use of laser therapy with CPP-ACP-fluoride varnish significantly enhanced the remineralization of temporary teeth enamel. The 980 nm diode laser + CPP-ACP-fluoride varnish showed the most pronounced improvement in remineralization, while the 808 nm diode laser alone also effectively increased calcium solubility. These findings suggest that higher wavelength diode lasers, particularly when combined with remineralizing agents, can effectively enhance the mineral content of primary teeth and promote enamel remineralization.

The German government's ambitious goal of achieving CO2-neutrality by 2045 has prompted a focus on improving building insulation as a vital step toward energy efficiency. However, in this process, existing radiators and boilers are often left unchanged, leading to inefficiencies due to oversized heating systems. This paper presents various approaches to reduce the required radiator inlet temperature, drawing on data from 100 multifamily buildings. The approaches include heat reserve reduction, heat power shifting, uniform radiator usage, and heat requirement analysis. These approaches collectively aim to lower flow temperatures and decrease peak heat loads, reducing energy consumption, and minimizing waste in compliance with the user comfort temperature. The findings reveal that the application of these methods can lead to substantial temperature reductions, with an average decrease of 20.82 K and 7.28 K for the highest necessary flow temperature in the provided example. Furthermore, peak load reductions of 21.07% and 13.65% were achieved, demonstrating the potential to enhance energy efficiency. While each approach can be applied individually, their synergistic implementation can highly increase the efficiency of water to x heat pumps, due to the lower required flow temperatures.

Climate change is increasing air temperatures and altering the precipitation and hydrological re-gime on a global scale. Challenges arise when assessing the impacts of climate change on the local scale for water resources management proposes, especially for low mountain headwater catch-ments that not only serve as important water towers for local communities, but also have distinct hydrological characteristics. Until now, no low flow or hydrological drought studies have been carried out on the Lauter River. This study is unique in that it compares the Lauter River, a transboundary Rhine tributary with a nearby station on the River Rhine just below its confluence at the French-German border. The Lauter catchment is a mostly natural, forested catchment, however, its water course has been influenced by past and present cultural activities. Climate change disturbances cascade through the hydrologic regime right down to the local scale. As we are expecting more low flow events, the decrease in water availability could cause conflicts be-tween different water user groups in the Lauter catchment. However, the choice of different methods for identifying low flow periods may cause confusion for local water resources manag-ers. Using flow rate time series of the Lauter River between 1956 and 2022 we compare for the first time three low flow identification methods: the variable threshold method (VT), the fixed threshold method (FT), and the Standardized Streamflow Index (SSI). Similar analyses are applied and compared to the adjacent Maxau station on the Rhine River for the same time period. This study aims at 1) interpreting the differences amongst the various low flow identification methods and 2) revealing the differences in low flow characteristics of the Lauter catchment compared to the Rhine River. It appears that the FT reacts faster to direct climate or anthropogenic impacts whereas VT is more sensitive to indirect factors such as decreasing subsurface flow which is typical for small headwater catchments, such as the Lauter where flow dynamics react faster to flow disturbances. Abnormally low flow during the early Spring in tributaries such as the Lauter can help predict low flow conditions of the Rhine River during the following half year and espe-cially for the summer. The results could facilitate Early Warning of hydrological droughts and drought management for water users in the Lauter catchment and further downstream along some of the Rhine.

As the PCIe 6.0 specification places higher requirements on signal integrity and transmission la-tency, it becomes especially important to improve signal transmission performance at the physical layer of the transceiver interface. Retimer circuit as a key component of high-speed serial interface, its delay and jitter size directly affect the overall performance of PCIe. For the conventional Retimer circuit with large latency and low jitter performance, this paper proposes a low latency and low jitter Retimer circuit based on CDR+PLL architecture for PCIe 6.0, using a jitter canceling filter circuit to eliminate the frequency difference between the retiming clock and data, reduce the retiming clock jitter, and improve the quality of Retimer output data; The data is sampled using the retiming clock and then output, avoiding the problem of large penetration latency of con-ventional Retimer circuits. The circuit is designed using CMOS 28nm process. Simulation results show that when 112Gbps PAM4 data is input to the Retimer circuit, the Retimer penetration la-tency is 27.3 ps, which is 83.5% lower than the conventional Retimer structure; the output data jitter is 741 fs, a 31.4% reduction compared to the conventional Retimer structure.

Time-modulated sparse circular array (TMSCA) with elements uniformly excited is designed and synthesized in this paper. By utilizing rotationally symmetric structure, the array geometry and the time modulation of the TMSCA is presented, and the radiation patterns in frequency domain are formulated. In order to achieve the desired radiation pattern at the operating frequency and suppress the sideband radiation, the synthesis problem is established and solved by the proposed harmony search-convex programming (HS-CP) algorithm in two dependent optimizations. Two designs are presented, and the numerical results indicate that the TMSCA with rotationally symmetric structure has the advantages of designing time-modulated sparse arrays with superior performance.

Following the central dogma of molecular biology, gene expression heterogeneity can aid in predicting and explaining the wide variety of protein products, functions, and, ultimately, heterogeneity in phenotypes. There is currently overlapping terminology used to describe the types of diversity in gene expression profiles, and overlooking these nuances can misrepresent important biological information. Here, we describe transcriptome diversity as a measure of the heterogeneity in 1) the expression of all genes within a sample or a single gene across samples in a population (gene-level diversity) or 2) the isoform-specific expression of a given gene (isoform-level diversity). We first overview modulators and quantification of transcriptome diversity at the gene level. Then, we discuss the role alternative splicing plays in driving transcript isoform-level diversity and how it can be quantified. Additionally, we overview computational resources for calculating gene-level and isoform-level diversity for high-throughput sequencing data. Finally, we discuss future applications of transcriptome diversity. This review provides a comprehensive overview of how gene expression diversity arises, and how measuring it determines a more complete picture of heterogeneity across proteins, cells, tissues, organisms, and species.

Recently considered modifications to public policy and trends in technology transfer practices have underscored the need for validated instruments to assess the maturity of technologies. This paper details a study that aimed to develop and present a generalized technology readiness level (GTRL) scale that a variety of professionals and researchers could use to assess the maturity of technologies in a range of contexts. Of particular interest is developing and validating an instrument that technology transfer professionals in federal laboratories, universities, and the private sector in the United States of America can use to assess the maturity of technologies to facilitate their technology transfer efforts. The primary goal of the research study was to highlight the need for validated measurement instruments for assessing the maturity of technologies in these contexts, test methods for validating the GTRL scale and other readiness level scales, and fill the knowledge gap regarding methods for properly validating such instruments. This included producing insights to inform future efforts to validate the GTRL scale as well as efforts to develop and validate other instruments to measure technology maturity. The study provides specific recommendations relevant to determining the face validity, content validity, inter-rater reliability, and intra-rater reliability of the GTRL scale and other such instruments for assessing technology maturity.

This paper presents Tiltification, a multi modal spirit level application for smartphones. The non-profit app was produced by students in the master project “Sonification Apps” in winter term 2020/21 at the University of Bremen. In the app, psychoacoustic sonification is used to give feedback on the device’s rotation angles in two plane dimensions, allowing users to level furniture or take perfectly horizontal photos. Tiltification supplements the market of spirit level apps with the unique feature of auditory information processing. This provides for additional benefit in comparison to a physical spirit level and for more accessibility for visu- ally and cognitively impaired people. We argue that the distribution of sonification apps through mainstream channels is a contribution to establish sonification in the market and make it better known to users outside the scientific domain. We hope that the auditory display community will support us by using and recommending the app and by providing valuable feedback on the app functionality and design, and on our communication, advertisement and distribution strategy.

Accurate forest reference and emission level (FRL, FREL) with related policies and regulations are the key determinants in establishing sustainable forest ecosystem management programmes (e.g. REDD+). This fundamental is for promoting and sustaining climate smart agricultural practices in a changing climate. With the aim to deliver better knowledge to the scientific community and policy makers on regulations and existing tools for more rigorous scientific communication when it comes to FRL and FREL accountability and policies. Thus, this review investigates forest in the changing climate and policies and underlines the performance of land use transition and intensity analysis towards deforestation with some key examples and achievements (e.g. Togo). Simply put, (i) forest as break of greenhouse gas (GHGs) and ecosystem regulator, (ii) policies and REDD+ actions, (iii) potential drivers and (iv) transition and intensity analysis approach for their accountability are discussed. In sum, impressive studies, policies and regulations are under initiations and implementations regarding the role, place and evaluation of forest losses and its ecosystem functions and services. However, there are still some gaps when it comes to: the choice of the evaluation methods in the real context of a specific ecosystem as well as the firm implementations of formulating policies in developing countries. This paper concludes with some policy measures for forest sustainability, carbon enhancement and accountability.

Fixed offshore wind turbines continue to be developed for high latitude areas where not only wind and wave loads need to be considered, but also moving sea ice. Current rules and regulations for the design of fixed offshore structures in ice-covered waters do not adequately consider effects of ice loading and its stochastic nature on fatigue life of the structure. Ice crushing on such structures results in ice-induced vibrations, which can be represented by loading the structure using a variable-amplitude loading (VAL) sequence. Typical offshore load spectra are developed for wave and wind loading. Thus, a combined VAL spectrum is developed for wind, wave, and ice action. To this goal, numerical models are used to simulate the dynamic ice-, wind-, and wave-structure interaction. The stress time-history at an exemplarily selected critical point in an offshore wind energy monopile support structure is extracted from the model and translated into a VAL sequence, which can then be used as a loading sequence for the fatigue assessment or fatigue testing of welded joints of offshore wind turbine support structures. This study presents the approach to determine combined load spectra and standardized time series for wind, wave, and ice action.

Background/Objectives: Intervertebral disc degeneration is the most common cause of low back pain (LBP) and lumbosciatica is a major challenge to healthcare systems worldwide. ''For years, ozone therapy has been used with excellent results in intervertebral disc disease and in patients with LBP, thanks to its anti-inflammatory and pain-relieving action.'' At the other side, the repair effect fulfilled by porcine collagen, is a novelty to approach this pathology. In vitro studies have demonstrated the positive action of porcine collagen in extracellular matrix remodeling and homeostasis These tissue changes, associated with LBP, may suggest an indication for combined ozone/collagen treatment in patients with LBP. However, no studies have been reported regarding this combination of treatments. Methods: The present work compared two treatment groups (each of 10 LBP patients): A) Oxygen-Ozone Therapy (OOT) vs. B) OOT plus porcine collagen type 1 injections (COL I). Pain intensity and physiological function were assessed by the numerical rating scale (NSR) method. The Roland-Morrison questionnaire was used to assess disability. Patient data were acquired before, during and at six months of follow-up. Significant differences were assessed by ANOVA and T-Student test. Results: The analyses revealed significant statistical differences comparing the two arms, where, the OOT COL I treatment demonstrated a booster efficacy in pain, while the questionnaire revealed a reduction in disability. Conclusions:. The combination of these two therapies could be effective for the management of LBP. However no studies have been reported in literature regarding this therapeutic combination.

The purpose of the study is to show the effect of the intake of vitamin C obtained from a diet rich in fruit and vegetables or vitamin C supplements on the level of vitamin C in the plasma. The level of vitamin C in plasma were determined before the study (T1), and after five months (T2). Moreover, a medical record was carried out and a questionnaire on the habits such as general eating and specific consumption of food rich in vitamin C. Both of them were completed before and after five months. In addition, related anthropometric analyses were carried out. The results of the first determination of vitamin C level in plasma were between 1.0 and 16.0 mg/L and the results of the second determination of vitamin C in plasma were between 4.9 and 14.1 mg/L. Furthermore, it was identified that 50% of the questioned people had a low fruit intake. Raw vegetables were consumed by fewer people, the intake being higher during the main meals. The correlation of plasma vitamin C with the eating habits of the subjects to the study points out an interdependence between the consumption of fruit and vegetables and the level of vitamin C in the plasma.

Background : Our objectives were to investigate the incidence of elevated methemoglobin level among COVID-19 patients at intensive care unit. The correlation of methaemoglobinemia with mortality and some haematological parameters was also tested. Methods: The diagosis of coronavirus -19 infection was confirmed by RT-PCR. The quantitative method for determination of methemoglobin was it’s cyanide derivative by spectrophotometry. The reference range was less than 2 percent. Results: There were altogether 46 patients (11 male, 35 female) included. Their median age value was 70 y. ( 29 – 89). The methemoglobin median value was 4,3%. 15 of 46 patients died. The methemoglobin median value of departed patients was 8 % , and 2,5% was among survivors. ( P= 0,001) 19 patients were blood transfused. Their methemoglobin median was 11 % , otherwise the non transfused patients presented 2,7 % methemoglobin median. ( p= 0,001). We performed two binary logistic regression calculation, in order to judge the elevated methemoglobin level as an independent risk factor for the mortality. The predictor of methaemoglobin was 0,062 the constant -1,266 the odds ratio 1,06. The other binary logistic regression tested the fact of transfusion for the mortality. Predictor of transfusion 1,1474, constant -1,2527 odds ratio 3,15 There was no significant correlation between methemoglobin and CRP level. Discussion: The methemoglobin is not able to transport oxygen. It’s association with mortality is discussed by some papers.There are several hypothesis in the literature to explain it’s occurrence in COVID-19. The role of coronavirus proteins as oxydative agents was mentioned. The importance of enzyme defect is emphasized. The impact of reactive oxygen free radicals in inflammation is also probable. Some papers mentioned applying local anesthetics and azythromycin as a risk. The role of transfusion is obscure, because the methemoglobin can be elevated in blood conserves during storage. Conclusion: Testing the methemoglobin seems to be important, but the pathomechanism needs further research.. The traceability and standardization of different measurement methods at intensive care units is the key for defining it’s pathogenetic role.

Introduction: Since its emergence COVID-19 has become a global health threat. In Uganda, a number of COVID-19 Standard Operating Procedures (SOPs) have been put in place by the Ministry of Health Uganda, to mitigate the outbreak of the deadly COVID-19 pandemic among the population. Despite the putting in place COVID-19 SOPs, the deadly COVID-19 pandemic is still ravaging the population of Iganga District. This study investigated the level of compliance to guidelines for prevention of COVID-19 in public places in Iganga District so as to guide decision makers in making recommendations towards the entire public in order to prevent community acquisition and spread of COVID-19. Methodology: To deliver answers to the research objectives, the study adopted a cross-sectional survey design to guide the study process. Quantitative method of data collection using observational checklist were adopted for this study. The same data abstraction form helped to collect data from 3 public places which included: 3 markets, 5 public transport stations and 8 financial banks. Compliance was measured were the YES scored 1 and NO scored 0 and the ten indicators measured included: temperature screening, wearing of face masks, hand washing or sanitizing, physical distancing of at least 2 meters, information display on COVID-19, regular cleaning of public service places, cleaning of communal places, adequate ventilation, adequate waste management facilities and cleanliness of the work area. Overall a 4 point Likert scale used was: 0-2 poor, 3-5 fair, 6-8 good, 9-10 excellent were each indicator was equally important. Data was entered, cleaned and analyzed using Microsoft Excel 2019 spread sheet packages to generate tables and bar graphs. Results: Out of 5 public transportation stations studied, 80% were observed to be poorly compliant to covid-19 SOPs. On the other hand, out of 8 Financial Banks included in this study, 75% were observed to have excellent compliance levels to COVID-19 SOPs. Meanwhile, out of 3 Market places studied, 66.7% were observed to be poorly compliant to covid-19 SOPs. Conclusion; The results of the study revealed that; public places in Iganga district generally have low level of compliance to COVID-19 SOPs in terms of temperature screening, wearing of face masks, hand washing or sanitizing, social distancing of at least 2 meters and information display on COVID-19 Dos and Don’ts. Our findings suggest that there is a need to mobilize the population in Iganga district to comply with COVID-19 SOPs in terms of temperature screening, wearing of face masks, hand washing or sanitizing, social distancing of at least 2 meters and information display on COVID-19 Dos and Don’ts.

According to the World Health Organization (WHO), dementia is the seventh leading reason of death among all illnesses and one of the leading causes of disability among the world’s elderly people. Day by day the number of Alzheimer’s patients is raising. Considering the increasing rate and the dangers, Alzheimer’s disease should be diagnosed carefully. Machine learning is a potential technique for Alzheimer’s diagnosis but general users do not trust machine learning models due to the black-box nature. Even, some of those models do not provide the best performance because of using only neuroimaging data. To solve these issues, this paper proposes a novel explainable Alzheimer’s disease prediction model using a multimodal dataset. This approach performs a data-level fusion using clinical data, Freesurfer MRI segmentation data, and psychological data. For Alzheimer’s disease vs cognitively normal prediction, the random forest classifier provides 100% accuracy. Furthermore, Alzheimer’s disease and non-Alzheimer’s dementia should be classified properly because their symptoms are similar. To the best of our knowledge, we are the first to present a three-class classification on Alzheimer’s disease vs cognitively normal vs non-Alzheimer’s dementia and achieved 99.86% accuracy using an ensemble model. Besides, a novel Alzheimer’s patient management architecture is also proposed in this work..

The detection of SARS-Cov-2 in the sewage and water resources has increased the awareness among the people about the possibility survival of SARS-Cov-2 in the environment and the potential to transmit into the human through food chain or water resources. Moreover, the surface contaminated by the virus need to be disinfected frequently by using an effective disinfectant, the current chapter discussed the efficiency of the most traditional treatment process of the sewage and wastewater, and their role in the elimination of the virus as well as the sterility assurance level concept. Moreover, the chemical disinfectant used currently and their temporary efficiency has been reviewed.

Abstract: As the massive deployment of the heterogeneous IoT devices in the coexisting environment such as smart homes，Traditional channel-based spectrum sharing algorithms such as CSMA has great limitations to further optimize spectrum utilization. Therefore, exploring more efficient spectrum sensing algorithm becomes hot topic these years. This paper proposes Subcarrier-Sniffer, which utilizes Channel State Information (CSI) to sense the subcarrier-level detailed status of the spectrum. In order to evaluate the performance of Subcarrier-Sniffer, we implemented Subcarrier-Sniffer by USRP B200min, and the experimental results show that when the distance between Subcarrier-Sniffer and the monitored devices is not great than 7 m, the accuracy of subcarrier-level spectrum sensing could achieve 100% in our settings.

African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

A novel low-power MOS-only voltage reference is presented. The Enz-Krummenacher-Vittoz (EKV) model is adopted to provide a new perspective on the operating principle. The normalized charge density, introduced as a new variable, serves as an indicator when trimming the output temperature coefficient. The proposed voltage reference consists of a specific current generator and a 5-bit trimmable load. Thanks to the well-match between the current source stage and the output stage, the non-linear temperature dependence of carrier mobility is automatically canceled out. The circuit is designed in 55 nm COMS technology. The operating temperature ranges from -40 ∘C to 120 ∘C. The average temperature coefficient of the output voltage can be reduced to 21.7 ppm/∘C by trimming. The power consumption is only 23.2 nW with a supply voltage of 0.8 V. The line sensitivity and the power supply rejection ratio at 100 Hz are 0.011 %/V and -89 dB respectively.

Background: In past years recreational diving has attracted more and more interest and among such divers an increasing number of diabetic divers. However, there is limited research on the accuracy of CGM systems under hyperbaric conditions and consistently diving guidelines make little reference to the use of CGM. Subject and Method: This exploratory study collected blood glucose samples of one diabetic diver over four dives and assessed the deviation of intersitial glucose values from two CGM systems based on 33 samples. A notable step of this method is to collect the data from actual dives under water. Results: The results indicate that a) under hyperbaric conditions of up to 2bar additional pressure and b) after decompression both CGM systems work comparably accurate as indictated by the manufacturer under normal conditions. This has been checked in terms of MARD and Clarke Error Grid Distirbution. Conculsion: For diabetic divers the results suggest they may take CGM monitors with them on dives to react to potential hypoglycemic events before they occur, i.e. when it is still safe to supplement glucose. For dive guidelines the results imply that these could reference CGM for dive planning and monitoring during the dive to increase divers‘ safety. For research this exploratory confirms the current hypothesis that neither increased pressure nor saltwater have an effect on blood glucose and the functioning of CGM systems. Further research may include additional sampling (number and depth) and more elaborate blood glucose measurement. The experimental setup applied is an efficient way to test further CGM systems.

Yttrium oxide (Y2O3) resistive random-access memory (RRAM) devices were fabricated using the sol–gel process on indium tin oxide/glass substrates. These devices exhibited conventional bipolar RRAM characteristics, without requiring a high voltage forming process. The effect of current compliance on the Y2O3 RRAM devices was investigated and revealed that as the set current compliance values increased, the resistance values gradually decreased. Consequently, intermediate resistance values were obtained, which are suitable for multi-level cell (MLC) switching. The fabricated Y2O3 RRAM devices were capable of functioning as an MLC with a capacity of 2 bits in one cell, utilizing three low resistance states and one common high resistance state. The potential of the Y2O3 RRAM for neural networks was further explored through numerical simulations. Hardware neural networks based on the Y2O3 RRAM demonstrated effective digit image classification with a high accuracy rate of approximately 88%, comparable to the ideal software-based classification (~92%). This suggests that the proposed RRAM has the potential to be utilized as a memory component in practical neuromorphic systems.

Malaria infection is a multifactorial disease partly modulated by host immuno-genetic factors. Recent evidence has demonstrated the importance of Interleukin-17 family proinflammatory cytokines and their genetic variants in host immunity. However, limited knowledge exists about their role in parasitic infections such as malaria. We aimed to investigate IL-17A serum levels in patients with severe and uncomplicated malaria, whether IL-17A gene polymorphisms are involved in severe malaria susceptibility and the polymorphism’s influence on the IL-17A serum levels. 125 malaria patients and 48 free malaria controls were enrolled in this research. Malaria patients were classified into severe malaria (SM) and uncomplicated malaria (UM). IL-17A serum levels were measured with ELISA. PCR and DNA sequencing were used to assess host genetic polymorphisms in IL-17A. We performed a multivariate regression to estimate the impact of human IL-17A variants on IL-17A serum level and malaria outcome. Elevated serum IL-17A levels accompanied by increased parasitemia were found in SM patients compared to UM and controls (P&lt;0.0001). Also, the IL-17A levels were lower in SM patients who were deceased than in those who survived. In addition, the minor allele frequencies (MAF) of two IL-17A polymorphisms (rs3819024 and rs3748067) were more prevalent in SM patients than UM patients indicating an essential role in SM. Interestingly, the heterozygous rs8193038 AG genotype was significantly associated with higher levels of IL-17A than the homozygous wild type (GG). According to our results, it can be concluded that IL-17A may play a role in protection against fatal malaria outcomes.

The combined heat and power system is based on the principle of "cascade utilization of thermal energy" for system integration and optimization. The rational utilization of energy, as well as the rational arrangement of energy flow and the process optimization combination of the overall system are taken into account in order to achieve multifunctional goals in the field of thermal engineering. The present paper presents a detailed assessment of combined heat and power systems from above standpoints. This article is divided into two parts “CHP based on thermo-dynamic cycles” and “CHP based on non-thermodynamic cycles”. Each part is then classified based on power subsystem energy consumption efficiency (high or low), including Rankine cycle, ORC, Stirling cycle, gas turbine, reciprocating engine, PVT and fuel cell. The present paper also helps identify the research gaps in this area and provides direction on future studies on combined heat and power systems.

The study examined the learner autonomy in EFL learning at the undergraduate level in the context of Bangladesh. It investigated the effectiveness of learner autonomy on EFL learning. Besides, it explored the factors affecting autonomous learning in English language class. This study adopted a mixed- method approach. Data were collected from 60 students who had just completed their second semester at a private university in Dhaka city. The respondent students attended the compulsory English foundation course including their two semesters. Data were also collected from 12 ELT teachers teaching at the tertiary education level. Five EFL classes were observed following a sample of classroom observation schedule. Both open-ended and closed-ended questionnaires were used by the researchers for collecting the data from the students and teachers. Major findings of the study showed that lack of confidence, teachers’ dependency, lack of motivation, short-term goals in learning, huge confusions and confinement in memorization, tendency of using mother tongue and unawareness to self-evaluation of students affected learner autonomy in EFL learning of the undergraduate students. However, the study revealed that motivated students hardly faced any difficulties in achieving maximum outcomes with autonomous learning in the EFL class. Finally, the researchers gave a number of recommendations to bring out effective EFL learning with learner autonomy.

In recent years, farmers and policymakers have faced ample challenges and have struggled to support the sustainability of the agricultural sector. Sustainable agriculture encompasses multiple concepts, and its performance produces extensive debate about data requirements, appropriate indicators, evaluation methods, and tools. Under the European Union (EU) financed project FLINT (Farm Level Indicators for New Topics in policy evaluation), detailed data have been collected at the farm level to provide broader coverage of sustainability indicators on a wide range of relevant topics to facilitate the assessment of sustainability performance. The approach has been applied in a pilot network of representative farms at the EU level, considering the heterogeneity of the EU farming sector to provide data infrastructure with up to date information for sustainability indicators. This study aims to assess sustainability performance at the farm level in Greece. Representative and dominant agricultural systems, such as permanent crops, olive trees, arable crops, and livestock (sheep) farms, comprise the Greek sample. It uses the analytical hierarchy process (AHP) methodology and attempts to gain insights into the sustainability performance of agricultural systems. The outcome of the sustainability assessment reveals knowledge and develops support for strategic farm choices in order to support both farmers and policymakers towards more sustainable development plans. The results indicate that three typical Mediterranean farming systems, like permanent crops, olive trees, and extensive livestock systems (sheep farms), are more sustainable in contrast to intensive and arable crop farms.

The concept of transit-oriented development (TOD) has been widely recognized in recent years for its role in reducing car traffic, improving public transportation, and enhancing traffic sustainability. This paper conducts empirical research on a developed rail transit network, using Shanghai as a case study. In addition to traditional TOD features, other factors based on urban rail transit are introduced, including multi-level modeling (MLM), which is used to analyze the possible factors influencing rail patronage. To avoid the bias of research results led by the correlation between independent variables, factors are divided into two levels. The first level includes three groups of variables: the built environment, station characteristics, and socioeconomic and demographic characteristics. The second level includes a set of variables which are regional characteristics. Results show that the most significant impact on train patronage is station location in the business district area. Other factors that have a positive effect on promoting rail transit travel include the number of service facilities around the station, degree of employment around the station, economic level, intensity of residential development, if the station is a transfer station, the operating period of the station, and the size of the large transportation hub around the station.

Ventilation in cities is crucial for the well being of their inhabitants. Therefore, local governments require air ventilation assessments (AVAs) prior to the construction of new buildings. In a standard AVA, however, only neutral stratification is considered, although diabatic and particularly unstable conditions may be observed more frequently in nature. The results presented here indicate significant changes in ventilation within most of the area of Kowloon City, Hong Kong, included in the study. A new definition for calculating ventilation was introduced, and used to compare the influence of buildings on ventilation under conditions of neutral and unstable stratification. The overall ventilation increased due to enhanced vertical mixing. In the vicinity of exposed buildings, however, ventilation was weaker for unstable stratification than for neutral stratification. The influence on ventilation by building parameters, such as the plan area index, was altered when unstable stratification was considered. Consequently, differences in stratification were shown to have marked effects on ventilation estimates, which should be taken into consideration in future AVAs.

This paper presents the results of a study aimed at understanding how technology maturity level influences the incidence of university technology transfer to the private sector. The study examined the topic from the perspective of private sector organizations. It used data from a random sample of patent applications filed with the United States Patent and Trademark Office and a theoretically guided sampling of multiple cases of private sector organizations that contemplated obtaining and assimilating technologies created at universities in the United States. The patent application data were analyzed using nonparametric statistical techniques and the case data were analyzed using qualitative comparative analysis (QCA). The findings of the study suggest that the typical maturity level of technologies created at U.S. universities is a TRL-5 or lower on as scale adapted from the NASA technology readiness level (TRL) scale. A technology maturity level of TRL-6 or higher is likely an insufficient but necessary part of at least one unnecessary but sufficient configuration of conditions that tends to result in the occurrence of university technology transfer. However, under certain circumstances, a technology maturity level of at least TRL-6 could be a sufficient but unnecessary condition for the occurrence of university technology transfer. These findings have several important implications. First, they provide support for the notion that university technology transfer is subject to causal complexity. Moreover, it may be possible to increase the incidence of university technology transfer in the United States by implementing public policy and practices that explicitly take technology maturity level into consideration.

Thresholding is considered as a statistical-decision making theory which can lessen the average error incurred in allocating pixels to two or more groups. The traditional Bayes decision rule can be applied with the prior knowledge of the Probability Density Function (PDF) of each class. It is surmised that a threshold resulting in the best class separation is the optimal one. In this paper, Otsu’s thresholding for image segmentation has been implemented. The well-known Otsu’s method is to learn a threshold that can maximize the between-class variance or equivalently make light of the within-class variance of the entire image. At first, a color image of a tree is taken. After that, the image is transformed into a grayscale image. Then in the first part, two-level thresholding is conducted, and later on, three-level thresholding is also applied. Again, two-level thresholding, as well as three level thresholding, are also applied to some other images. Finally, the comparison is made between two level thresholding and three level thresholding

Low volatility ETFs have become popular in recent year because investors are starting to understand the advantages involved in investing in those ETFs compared to traditional index investment. In this research I have examined the performance of six popular low volatility ETFs, four of them invest in U.S stocks and the other two invest in other developed and emerging markets. Results have pointed out that not only five of the low volatility ETFs have exposed their investors to lower risk, four of them have also produced higher returns. The advantage of investing in low volatility ETFs is prominent in the U.S stock market. All three sizes of stocks categories (Large, Mid and Small Capitalization) low volatility ETFs have outperformed their indexes bench marks in terms of risk and returns. For the non U.S stock investing, while no advantage have been found for investing in low volatility ETFs for developed countries, significant lower risk was found for emerging markets.

Low dropout (LDO) regulators are widely used in portable electronic devices because they 1 occupy small chip and printed circuit board (PCB) areas. This work presents the design of a low 2 noise low dropout (LDO) linear voltage regulator using folded cascode operational amplifier and 3 source follower buffer for frequency compensation. The proposed design achieves low output noise 4 with feedback loops, which makes it possible to improve load and line regulations as well as the 5 transient response for voltage applications in comparison with the literature. The designed LDO 6 linear regulator works under the input voltage of 2.8-4.8 V and provides up to 100 mA load current 7 for an output voltage of 2.6 V. 8 9 Moreover, the operational amplifier design contributes to the major reduction in the frequency 10 noise, and make sure the stability of LDO under different conditions. Furthermore, the novel LDO 11 design topology has very less dropout voltage, fast transient response and minimized power dissi- 12 pation under maximum load current, worst process corner, and maximum temperature to achieve 13 high power efficiency, maintain output voltage in the presence of fast load changes, and to lower the 14 power loss across the pass element especially at high load. Design criteria are addressed in detail. 15 16 This LDO topology is able to achieve ultra-low noise i.e. 2 /muv/√Hz for frequency >1kHz. The 17 proposed LDO is implemented in the cadence virtuoso H9A with CMOS 130 μm technology.

Logistics industry has been found to be among the key sources of carbon emission. In Vietnam logistics industry, there is a considerable difference between the number of foreign and Vietnamese firms as well as the proportion of markets that they are taking. This study is to research the low-carbon emission measures conducted by domestic and foreign invested logistics service providers (LSPs) and compare the results of the two groups. Both qualitative and quantitative approaches are applied. Literatures in relevant fields are reviewed and expert opinions are taken for structuring a questionnaire which was later distributed to 279 LSPs, with 166 returned and 159 being valid for data calculation. The results imply that there are differences in extension of applications of low-carbon practices between foreign and domestic firms. Except for transport mode switch and energy-saving lighting, the other practices witness that adoption levels of foreign LSPs are higher than their counterparts, which is possibly thanks to their global operation, more comfortable capital resources and awareness level of green initiative necessity. In conclusion, a comparison between the application conducted by foreign-invested firms and domestic ones, which has not been investigated before, was made.

Historical maps constitute unique sources of retrospective geographic information. Recently, several map archives containing map series covering large spatial and temporal extents have been systematically scanned and made available to the public. The geographic information contained in such data archives allows extending geospatial analysis retrospectively beyond the era of digital cartography. However, given the large data volumes of such archives and the low graphical quality of older map sheets, the processes to extract geographic information need to be automated to the highest degree possible. In order to understand the salient characteristics, data quality variation, and potential challenges in large-scale information extraction tasks, preparatory analytical steps are required to efficiently assess spatio-temporal coverage, approximate map content, and spatial accuracy of such georeferenced map archives across different cartographic scales. Such preparatory steps are often neglected or ignored in the map processing literature but represent highly critical phases that lay the foundation for any subsequent computational analysis and recognition. In this contribution we demonstrate how such preparatory analyses can be conducted using classical analytical and cartographic techniques as well as visual-analytical data mining tools originating from machine learning and data science, exemplified for the United States Geological Survey topographic map and Sanborn fire insurance map archives.

Digital-based differential amplifiers (DDA) are particularly suitable to low voltage digital integrated circuit technologies. This paper presents an exhaustive analysis of the digital-based analog amplifiers to take advantage of today's high-performance digital technologies and of computer-aided design (CAD) commonly employed to design integrated circuits. The operating principle and the main mathematical relations of the digital-based differential amplifiers are discussed along with an exhaustive explanation of its operating regions and of the corresponding power consumption. Finally, a detailed description of the design procedure of in UMC 180nm standard CMOS technology is shown.

HER2-low and ultra-low breast cancer (BC) have been recently proposed as new subcategories of HER2 BC, re-considering the immunohistochemical negative score of 0, 1+ or score of 2+/in situ hybridization (ISH) negative phenotype. In the present review we have outlined the needed criteria to exactly distinguish HER2 low and ultra-low BC. Recent clinical trials have demonstrated significant clinical benefits of novel HER2 directing antibody-drug conjugates (ADCs) in treating these group sof tumors. In particular, Trastuzumab-deruxtecan (T-Dxd), a HER2-directing ADC has been recently approved by the U.S. Food and Drug Administration as the first targeted therapy to treat HER2-low BC. Furthermore, ongoing trials, such as the DESTINY-Breast06, are currently evaluating ADCs in patients with HER2-ultra low BC. Finally we hope that new guidelines may help to codify HER2 low and ultra-low BC, increasing our knowledge of tumor biology and improving a targetable new therapeutical treatment.

Multidisciplinary Design Optimization (MDO) is the most active field in the design of current complex system engineering, which is possessed with such two difficulties as subsystem information exchange and analytical and computational complexity of systems. Therefore, an improved collaborative optimization algorithm based on ANN (artificial neural network) response surface was proposed dependent on the consistency constraint algorithm and concurrent subspace algorithm. As an optimization method with secondary structure, it satisfied only local constraints in discipline layer, but provided a coordinated mechanism for interdisciplinary conflict in system layer. Finally, it was applied in the multidisciplinary design optimization of autonomous underwater vehicle (AUV). As shown from the result, the MDO convergence stability and reliability of low resistance, low noise and high maneuvering performance of the AUV shape can be ensured by the improved collaborative optimization algorithm, thus verifying the effectiveness of the algorithm.

High-spin states of 192Tl are populated by the heavy ion fusion-evaporation reaction 181Ta(16O, 5n)192Tl at 97 MeV beam energy. A new level scheme with eight new levels is constructed and the level spins are tentatively assigned. The negative-parity yrast band is extended up to 23^{-}\hbar. Subsequently, the systematics of signature splitting and signature inversion are discussed for the negative-parity yrast band of odd-odd Tl isotopes including 192Tl, 194Tl, 196Tl, and 198Tl. With the increase of neutron number signature inversion is found in 196,198Tl at high-spin state in these four Tl isotopes. The reason may be due to the competition between neutron-proton interaction and Coriolis force.

Pandemics, and other risk-related contexts, require dynamic changes in behavior as situations develop. Human behavior is influenced by both explicit (cognitive) and implicit (intuitive) factors. In this study, we used psychological distance as a lens to understand what influences our decision-making with regards to risk in the context of COVID-19. The study was based on the rationale that our relational needs are more concrete to us than the risk of the virus. First, we explored the impact of social-psychological distance on participants’ risk perceptions and behavioral willingness. As hypothesized, we found that close social relationships of agents promoted willingness to engage in risky behavior. In the second phase, we tested an intervention designed to increase the concreteness of information about virus transmission as a mechanism to mitigate the bias of social influence. We found that the concreteness intervention resulted in significantly reduced willingness to engage in risky behavior. As such, communications aimed at changing the behavior of citizens during times of increased risk or danger, should consider conceptually concrete messaging when communicating complex risk, and hence may provide a valuable tool in promoting health-related behavior.

Cities are important sources of anthropogenic methane emissions. Municipal governments can play a role in reducing those emissions to support climate change mitigation, but they need information on the rate of emissions to context mitigation actions and track progress. Here, we examine the application of satellite data from the TROPOspheric Monitoring Instrument (TROPOMI) to estimate city-level methane emissions rates in a case study of the City of Calgary, Alberta, Canada. While satellites are touted as a global methane monitoring system, we found limited observational coverage over Calgary that precluded the reliability of measurement-based models to track the annual emissions. In this work, we integrated valid observations over three years (2020-22) and used mass balance modeling to derive a long-term averaged emission estimate. The column-averaged dry-air mole fraction (XCH4) enhancement over Calgary was small, 4.7 ppb, but within the city boundary, we identified local hot spots in the vicinity of known sources (wastewater treatment facility and landfills). The city-scale emissions estimate from mass balance was 215.4 ± 132.8 t/d CH4. This estimate is approximately four- and six-times larger than estimates from Canada's gridded national inventory report of anthropogenic CH4 emissions and the Emissions Database for Global Atmospheric Research (EDGAR v8.0), respectively. Valid observations are more common in warmer months and occur during a narrow daily overpass timeslot over Calgary – these effects may bias the emissions estimate. Overall, the findings from this case study highlight the challenge of deriving routine (sub-annual to annual) satellite-based estimates of city-scale methane emissions in similar geographic settings and suggest that more granular emissions inventories are needed to improve methane reporting.

Infrastructure and urban network operators, city users and industrialists are faced with complex issues to ensure the sustainability of the service, maintain, operate and develop their urban systems, while integrating environmental, economic and societal impacts and being resilient to unexpected geopolitical and climatic upheavals. Digital Twins are now recognized as the cornerstone of digital transformation. In the field of smart cities, they can enable all stakeholders to collaborate across disciplinary silos and foster digital transformation in urban and territorial projects to ensure sustainability, resilience and increased inventiveness. However, the application of the Digital Twin technology to Smart Cities lacks of standards. This paper proposes a high-level architecture for Digital Twins as an enabler of various levels of interoperation between key stakeholders of a Smart City. Such a technology-agnostic architecture, when implemented for a given Smart City, produces a middleware for large scale interoperability between actors involved in multiple supply chains of this territory.

Emotional intelligence and educational level are commonly associated with success in life and well-being. While multiple studies have explored these concepts independently, few studies have examined the impact of educational level on emotional intelligence and associated variables, such as well-being. A total of N = 202 participants were recruited online. Participants completed measures of emotional intelligence, well-being (i.e., happiness, self-esteem, personal growth). Overall, participants who previously obtained a bachelor’s degree displayed higher levels of emotional intelligence, happiness, self-esteem, and personal growth compared to those without an undergraduate degree. However, no differences were observed on any variable between individuals currently enrolled in a university and non-students. The results suggest that, while completing a university degree increases emotional intelligence and well-being, the stress of being a student may negatively impact the benefits obtained from attending university. Limitations and possible directions for future research are discussed.

Sediment thickness increases can cause floodplains and the water level increases. This has the potential to generate a flood. Using electromagnetic waves, Time Domain Electromagnetic (TDEM) detected resistivity or conductivity contrast of lithology in the subsurface. It is measured in the time domain. TDEM method has been developing for decades. Here we tried to develop a 1-D forward modelling program for central loop configuration in the water environment using the Adaptive Born Forward Mapping (ABFM) method. We simulated this program in several water environment conditions (such as freshwater, brackish water and saline water) to know its response. Preventing natural hazards, especially flood hazards which are caused by the floodplain increases is our motivation in this research. Our simulation shows that Central-Loop Configuration Time-Domain Electromagnetic Method is able for imaging the sediment thickness clearly. The response of this method is extremely sensitive in saline water to depth changing than in other water environments.

The national study analyzes sea level rise (SLR) impacts based on 36 different SLR and storm surge scenarios across 5.7 million geographic locations and 3 time periods. Taking an approach based on engineering design guidelines and current cost estimates, the study details projected cost impacts for states, counties, and cities. These impacts are presented from multiple perspectives including total cost, cost per-capita, and cost per-square mile. The purpose of the study is to identify specific locations where infrastructure is vulnerable to rising sea levels. The study finds that Sea Level Rise (SLR) and minimal storm surge is a $400 billion threat to the United States by 2040 that includes a need for at least 50,000 miles of protective barriers. The research is limited in its scope to protecting coastal infrastructure with sea walls. Additional methods exist and may be appropriate in individual situations. The study is original in that it is a national effort to identify infrastructure that is vulnerable as well as the cost associated with protecting this infrastructure.

The majority of urban inhabitants in low- and middle-income country (LMIC) cities live in deprived urban areas. However, statistics and data (e.g., local monitoring of Sustainable Development Goals - SDGs) are hindered by the unavailability of spatial data at metropolitan, city and sub-city scales. Deprivation is a complex and multidimensional concept, which has been captured in existing literature with a strong focus on household-level deprivation while giving limited attention to area-level deprivation. Within this scoping review, we build on existing literature on household- as well as area-level deprivation frameworks to arrive at a combined understanding of how urban deprivation is defined with a focus on LMIC cities. The scoping review was enriched with local stakeholder workshops in LMIC cities to arrive at our framework of Domains of Deprivations, splitting deprivation into three different scales and nine domains. (1) Socio-Economic Status and (2) Housing Domains (Household scale); (3) Social Hazards & Assets, (4) Physical Hazards & Assets, (5) Unplanned Urbanization and (6) Contamination (Within Area scale); and (7) Infrastructure, (8) Facilities & Services and (9) city Governance (Area Connect scale). The Domains of Deprivation framework provides a clear guidance for collecting data on various aspects of deprivation, while providing the flexibility to decide at city level which indicators are most relevant to explain individual domains. The framework provides a conceptual and operational base for the Integrated Deprived Area Mapping System (IDEAMAPS) Project for the creation of a data ecosystem, which facilitates the production of routine, accurate maps of deprived “slum” areas at scale across cities in LMICs. The Domains of Deprivation Framework is designed to support diverse health, poverty, and development initiatives globally to characterize and address deprivation in LMIC cities.

Sea-level rise is a problem increasingly affecting coastal areas worldwide. The existence of Free and Open-Source Models to estimate the sea-level impact can contribute to better coastal man-agement. This study aims to develop and to validate two different models to predict the sea-level rise impact supported by Google Earth Engine (GEE) – a cloud-based platform for planetary-scale environmental data analysis. The first model is a Bathtub Model based on the uncertainty of projections of the Sea-level Rise Impact Module of TerrSet - Geospatial Monitoring and Modeling System software. The validation process performed in the Rio Grande do Sul coastal plain (S Brazil) resulted in correlations from 0.75 to 1.00. The second model uses Bruun Rule formula implemented in GEE and is capable to determine the coastline retreat of a profile through the creation of a simple vector line from topo-bathymetric data. The model shows a very high cor-relation (0.97) with a classical Bruun Rule study performed in Aveiro coast (NW Portugal). The GEE platform seems to be an important tool for coastal management. The models developed have been openly shared, enabling the continuous improvement of the code by the scientific commu-nity.

Sea-level rise is a problem increasingly affecting coastal areas worldwide. The existence 15 of Free and Open-Source Models to estimate the sea-level impact can contribute to better coastal 16 management. This study aims to develop and to validate two different models to predict the 17 sea-level rise impact supported by Google Earth Engine (GEE) – a cloud-based platform for plan-18 etary-scale environmental data analysis. The first model is a Bathtub Model based on the uncer-19 tainty of projections of the Sea-level Rise Impact Module of TerrSet - Geospatial Monitoring and 20 Modeling System software. The validation process performed in the Rio Grande do Sul coastal 21 plain (S Brazil) resulted in correlations from 0.75 to 1.00. The second model uses Bruun Rule for-22 mula implemented in GEE and is capable to determine the coastline retreat of a profile through the 23 creation of a simple vector line from topo-bathymetric data. The model shows a very high correla-24 tion (0.97) with a classical Bruun Rule study performed in Aveiro coast (NW Portugal). The GEE 25 platform seems to be an important tool for coastal management. The models developed have been 26 openly shared, enabling the continuous improvement of the code by the scientific community.

Failure to adapt to climate change is currently considered one of the major threats affecting humanity. Hence, much effort is being put into discussing adaptation approaches. While many adaptation options have been identified, the academic literature does not present a simple process that local councils and community members can use to rank adaptation options. In this context, community members participating on planning processes are presented with many adaptation options, but with no objective approach for selection, which adds challenge to the planning process. With the objective of addressing this issue, this work proposes a simple equation that allows calculating the applicability level of adaptation options. Results can then be plotted into graphs that allow correlating adaptation options and applicability level, which can be easily understood by community members. To develop such equation, this work built on existing sophisticated models from where the indicators used on the equation were identified, as well as the relationship between them. A scale was proposed to help on identifying adaptation options that should be implemented on the short, medium and long term, and options that should only be implemented if the circumstance change.

Modern Monte-Carlo-based rendering systems still suffer from the computational complexity involved in the generation of noise-free images, making it challenging to synthesize interactive previews. We present a framework suited for rendering such previews of static scenes using a caching technique that builds upon a linkless octree. Our approach allows for memory-efficient storage and constant-time lookup to cache diffuse illumination at multiple hitpoints along the traced paths. Non-diffuse surfaces are dealt with in a hybrid way in order to reconstruct view-dependent illumination while maintaining interactive frame rates. By evaluating the visual fidelity against ground truth sequences and by benchmarking, we show that our approach compares well to low-noise path traced results, but with a greatly reduced computational complexity allowing for interactive frame rates. This way, our caching technique provides a useful tool for global illumination previews and multi-view rendering.

Academic staffs’ organizational commitment has been a critical issue to determine work performance for successes of University, as well as, to keep its Academic staffs motivation granted for achieving better work performance. This subject has therefore, been investigated so as to draw attention for enhancement of effective work performance and success. The main objective of this study was to assess academic staffs’ level of organizational commitment in Haramaya University. The study also investigated whether significant differences exist in academic staffs’ level of organizational commitment in reference to their gender and level of education. Researchers used cross-sectional research design. Primary and secondary data sources were used to study the problem. A commitment scale questionnaire was used to collect data from 275 participants who were selected from 877 target population of the study using stratified sampling technique; furthermore, focus group discussion and document review were also used to triangulate the data. The quantitative data were analyzed using both descriptive and inferential statistics; the qualitative data were also analyzed using narration methods of analysis. The study revealed that academic staffs of the university have moderate level organizational commitment. This implies relatively no more expected effective work performance for success of the institution; In addition, there were relative implications of turnover, turnover intention, absenteeism, and demotivation among staffs. The study further revealed that although there is no significance difference in employees’ level of commitment with reference to gender, their level of organizational commitment was significantly different in reference to level of education.

Multigranulation is a new approach to the Rough Set Theory, where several separability relationships are used to obtain different granulations of the universe. The Multigranulation starts from the existence of different contexts or subsets of features to characterize the objects of the universe. In this paper, a method for the generation of contexts from the construction of similarity relations is proposed.The proposed solution was evaluated in an international database using the KNN classifier. It was also applied in the solution of a real problem in Civil Engineering specifically in Traffic Engineering, the contexts generated from the proposal used to determine the features of higher incidence in the service level of the road. The results achieved both in the international database and in the proposed application demonstrate the applicability of the proposed method.

Protrusive defects on the color filter of thin-film transistor (TFT) liquid crystal displays (LCDs) frequently damage the valuable photomask. An fast method using side-view illuminations associated with digital charge-couple devices (CCDs) to detect the protrusive defect in the four substrates, which are the black matrix (BM), red, green, and blue. Between the photomask and substrate, the depth of field (DOF) is normally 300 μm for the proximity-type aligner; we select the four substrates to evaluate the detectability in the task. The experiment is capable of detecting measurements of 300 μm and even lower than 100 μm can be assessed successfully. The maximum error of the measurement is within 6% among the four samples. Furthermore, the uncertainty analysis of three standard deviations is conducted. Thus, the method is cost-effective to prevent damage for valuable photomasks in the flat panel display industry.

In the field of agricultural food production, the transition between organic and inorganic farming methods has been an issue of much debate. The debate, on one hand, stresses the urgency for the transition in order to preserve environment and health; and, on the other hand, emphasizes the pressure of maintaining food production for a large growing population. Thus, the dilemma is how to find an agricultural system that would balance between obtaining food security and ensuring a safe sustainably environment-friendly food production system. This article focuses on the debate, in the context of Bangladesh, and questions whether it is the proper time, and stage in the development process, to attempt the transition from inorganic conventional food production methods to organic food production methods. This article contemplates why the organic rice market is not expanding in Bangladesh, and attempts to explain the slow growth of the market through the two main factors of income constraint and lack of awareness among people about the environmental and health detriments of inorganic farming methods. The study is exploratory in nature, and finds that it is not mainly the lack of awareness but the income constraint that can be principally attributed to the slow expansion of the organic rice market in Bangladesh. Through exploring consumers’ awareness about organic farming methods and their demand for organic products, this study shows how income as the major constraint, besides price, affects consumers demand for organic and inorganic rice in Bangladesh. Income being identified as the major barrier reveals the potential of the organic rice market to grow in the future, as Bangladesh continues its journey towards becoming a middle-income country.