An analysis of the features of measurements and correction of phase distortions in optical waves propagating in the atmosphere at various levels of turbulence was performed. It is shown that with increasing intensity fluctuations, the limiting capabilities of phase correction decrease, and the phase of an optical wave that has passed through a turbulence layer consists of two components: potential and vortex. It was found that even in the region of weak fluctuations there is an overlap of spectral filtering functions for intensity and phase fluctuations. Areas of turbulence inhomogeneities have been identified that will have mutual influence and negatively affect the operation of the phase meter. It is noted that correlation functions, both phase and intensity, are less susceptible to this compared to structural functions. The results of experimental studies of the reconstruction of the wavefront of laser radiation distorted by atmospheric turbulence using a Shack-Hartmann wavefront sensor during vignetting and central screening of the entrance pupil of the optical system are presented. Studies have been carried out on the propagation of laser radiation along a horizontal atmospheric path for various levels of turbulence. The results are analyzed in terms of Zernike polynomials.

We document for the first time epsilon waves on the electrocardiogram of a patient with Dravet syndrome (DS) who does not exhibit structural cardiac pathology. DS, a severe form of pediatric epilepsy, involves mutations in the SCN1A gene, which disrupt sodium ion flow and increase the risk of sudden unexpected death in epilepsy. The epsilon waves, typically associated with arrhythmogenic right ventricular dysplasia, may also suggest a link between neuronal and cardiac dysfunctions. In our case, the epsilon waves appear to originate from abnormalities in sodium channels rather than structural changes in the myocardium. This finding underscores the importance of assessing both neurological and cardiac manifestations in patients with severe epilepsy, opening new avenues for the research and treatment of these interactions in DS.

An Indo-French campaign was conducted during May 2014 at Gadanki (13.5^oN, 79.2^oE), India, for investigating gravity wave (GW) coupling between the lower and middle atmospheres using a suite of experimental techniques. In this paper we are presenting the sources for those GWs which are observed at airglow layer (~87 km) using (OH) Airglow Imager during the campaign. For this purpose we have developed a background model atmosphere by combining the ERA-Interim, MSIS E 90 model and HWM 07 model data sets. Uniqueness of the present study lies in using near-real time background atmosphere data from simultaneous radiosonde and SVU Meteor Radar covering both source and propagation/ dissipation regions of GWs. We have observed 17 wave events and used GROGRAT model for reverse tracing to locate the source(s). When we searched for the sources near the terminal points or along the ray path, deep convection is found to occur but no strong wind shear. This indicates that the source for the observed GWs is deep convection. We have also simulated small scale waves that can reach mesosphere during different seasons (background conditions). GWs with periods less than 100 minutes and horizontal wavelengths less than 200 km are mostly reaching the mesospheric altitudes. Interestingly, it is found that only few GWs that are generated in the troposphere reach the mesospheric altitudes during the monsoon season, though strong sources like convection and wind shear persist throughout this season. Thus, background wind plays significant role in deciding the propagation of GWs in to upper atmosphere.

This paper presents an in-depth study of the stress wave behavior propagating in a Rayleigh–Love rod with a sudden cross-sectional area change. The analytical solutions of stress waves are derived for the reflection and transmission propagation behavior at the interface of the cross-sectional area change in the rod, considering inertia and Poisson’s effects. Examples solved by the finite element method are provided to verify the correctness of the analytical results. In addition to the forward analysis of Rayleigh–Love wave propagation in rods impacted by a striker rod, a nondestructive testing method is proposed to conduct the defect assessment in the rod type of the structure component with a sudden cross-sectional area change within a cover medium by using the measured signals at the measurable zone of the rod to be inspected.

Under the same seismic load, different local topography will have different effects, which is an important research field in seismic engineering. Hills are connected with valleys is a very typical terrain. Taking this terrain as an example, its response to the most destructive SH waves in the earthquake is studied. By simplifying and dividing the model, the wave functions satisfying the wave equation and boundary conditions in each region are constructed by using the complex function and moving coordinate method. The equations satisfying the boundary continuity conditions are established. With the help of calculation software, the numerical results are obtained. The influence of different parameters on ground motion is discussed.

The aim of the present work is to explore a different non-traditional approach to higher dimensional spacetime which differs from the usual approaches such as large extra space dimensions, warped extra space dimensions and multiple extra time dimensions. This approach will be referred to as "Dynamic" higher dimensional spacetime. By this term will be introduced a new kind of higher dimensional spacetime (more than the usual 3+1 dimensions), which behaves dynamically in the sense that time is not a fixed dimension but is the extra plus one dimension to the spatial dimensions of the phenomenon we are studying. For a higher dimensional phenomenon, the lower dimensional time will behave as space and the new time will be a plus one dimension, meaning if we study a 3-dimensional phenomenon then time is the usual 4th dimension but if we are studying a 4-dimensional phenomenon then its time will be an extra 5th dimension and for this phenomenon the 4th dimension will behave as space. All spatial dimensions are indistinguishable from each other and behave in the exact same way, which means that the important parameter is not the dimension we are studying (for example the 4th or the 5th) but the number of dimensions in which a phenomenon can interact and how higher dimensional phenomena interact with lower ones. This non-traditional approach to higher dimensional spacetime may appear confusing at first but will become clearer in the rest of the paper. For this reason, we will first associate the time dimension with propagation relative to space dimensions and change orthogonal to them in order to give the reader a better intuition. Following that, we will describe how higher - dimensional phenomena would appear to us, the 3 - dimensional observer and try to set some guidelines on how we should mathematically model higher - dimensional phenomena in order for us to make accurate predictions of their behaviour. Then we will express the general framework of a "Dynamic" higher - dimensional spacetime and turn our gaze to 4+1 – dimensional phenomena. We will explore how a mass term arises for 4 – dimensional waves by generalizing the frequency – speed – wavelength relation of 3D waves and give a basic description on a possible way to describe a 4+1 – dimensional disturbance in a scalar Energy Field in order to make accurate predictions on our 3+1 dimensional plane. In this framework we will derive the Klein – Gordon equation by generalizing the wave equation and ignoring all lower than 4+1 - dimensional disturbances and compere our mass term findings with the Klein – Gordon equation mass term and with results from gravity – induced quantum interference experiments. Lastly, we will describe how a "Dynamic" 5 - dimensional spacetime would appear in a 3D observer and examine whether our findings are compatible with quantum mechanics and the special theory of relativity.

The work contains a detailed analysis of the electromagnetic field originating from a point source placed above the layered structure.The surface impedance of the multilayer dielectric structure was determined. Based on the boundary conditions, a method for determining the surface impedance of a layered structure with a perfectly conductive screen and or a magnetic screen is presented. The resonance conditions and the conditions for the excitation of surface waves are derived. The integral expression defining the generalized impedance was analyzed with a view to adapting it to numerical implementation. This allowed the development of a computer program based on which calculations were made of the effect of excitation of waves on multilayer dielectric substrates.

This study delves into the intricate relationships among the constituent elements, wave speed, and energy of both mechanical waves and electromagnetic waves. By establishing connections with the string vibration equation, a compelling revelation emerges. Upon equating the energy and constituent element mass of one wave cycle of a homogeneous string with those of a single wave cycle of electromagnetic waves, it is evident that the wave speed derived from the string vibration equation consistently matches the constant speed of light. From this, a hypothesis takes root: electromagnetic waves manifest as waves resulting from the vibration of a uniform, elongated string-like material. The phenomenon of superluminal speed further fortifies the validity of this conjecture.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

The early detection of small cracks in large structures is a crucial requirement for the implementation of structural health monitoring (SHM) system with a low transducer density. This work presents the results of the analysis of scattering of a submillimeter notch type defect with semielliptical shape with a groove at constant width 100µm in a 4.1mm thick aluminum plate. The defect is investigated with an ultrasonic guided wave (UGW) A0 mode at 550 kHz to cover long range in a thick plate. The mode selection is obtained by interdigital transducers designed to operate with 5mm central wavelength. The novel contribution is the assessment of the scattering amplitudes at different orientations of the defect when the distance is large as 35 cm in pulse-echo mode or 70 cm in pitch-catch mode. The system model is based on Finite Element Model (FEM) simulations and the results are in good agreement with experimental tests. The detection of the defect is obtained by comparing the scattered signals from the defect with base line signals of the pristine laminate. The analysis of scattering features and the efficient excitation with a probing UGW show the potential implementation in real structural health monitoring (SHM) systems.

Extreme-mass-ratio inspirals (EMRIs) are significant observational targets for spaceborne gravitational wave detectors, namely, LISA, Taiji, and Tianqin, which involve the inspiral of stellar-mass compact objects into massive black holes with a mass range of approximately 104∼107M⊙. EMRIs are estimated to produce long lived gravitational wave signals with more than 105 cycles before plunge, making them an ideal laboratory for exploring the strong-gravity properties of the spacetimes around the MBHs, stellar dynamics in galactic nuclei, and properties of the MBHs itself. However, the complexity of the waveform model, which involves the superposition of multiple harmonics, as well as the high-dimensional and large-volume parameter space, make the fully coherent search challenging. In our previous work, we proposed a 10-dimensional search using Particle Swarm Optimization (PSO) with local maximization over the three initial angles. In this study, we extend the search to an 8-dimensional PSO with local maximization over both the three initial angles and the angles of spin direction of the MBH where the latter contribute a time independent amplitude to the waveforms. Additionally we propose a 7-dimensional PSO search by using a fiducial value for the initial orbital frequency and shifting the corresponding 8-dimensional Time Delay Interferometry responses until a certain lag returns the corresponding 8-dimensional log-likelihood ratio maximum. The reduced dimensionality likelihoods enable us to successfully search for EMRI signals with duration of 0.5 years and signal-to-noise ratio of 50 within a wider search range than our previous study. We discuss further developments, such as using a hierarchical search to narrow down the search ranges of certain parameters, and applying Graphics Processing Units to speed up the code. These advances aim to improve the efficiency and accuracy of the EMRI search algorithm.

We have studied the stochastic processes A and B concerning fade durations due to rain, by simulating attenuation time series A(t) (dB) in the zenith paths of GeoSurf satellite constellations, at sites located in different climatic regions, with the Synthetic Storm Technique. Process B gives the statistics of outages (occurrences), process A gives the statistics of outage duration (fraction of time), for the same rain attenuation threshold A(t)>S. The two processes are not independent, therefore, we have studied the relationship between their probabilities and defined a uniformity index 0<U(S)≤1. U(S) is useful for comparing real cases – fade durations fragmented in many different intervals, with changing S and site – and the limiting case of all fades lasting the same time. As S increases, U(S) increases, approaching 1 at very large thresholds. These results should guide the designers of future GeoSurf satellite constellations to consider the impact of A(t) on the diverse communications services. Process B (occurrences) impacts on non–real time services, such as data delivery, more disturbed by the number of outages rather than by their duration. Process A (fraction of time) impacts on real–time services such as television, video conference etc., more disturbed by the duration of the outage.

Heat waves are a significant consequence of climate change threatening public health by increased morbidity and mortality. The aim of this study was to estimate individuals’ knowledge, attitudes and practice related to heat waves. We conducted an exploratory cross-sectional study in Greece during September 2023. We employed a convenience sample of 1055 participants. We used the heat wave knowledge, awareness, practice and behavior scale (HWKAPBS) to measure our outcome. We measured several socio-demographic variables, such as gender, age, educational level, etc. as potential determinants. Mean scores for the knowledge, awareness, practice and behavior factors were 12.5, 22.7, 22.2 and 12.1 respectively. Females had higher scores on the four factors compared with males. We found a positive relationship between self-perceived health status and awareness, practice and behavior about heat waves. Similarly, we identified a positive relationship between self-perceived financial status and awareness and behavior about heat waves. Increased age was associated with increased practice score, while increased educational level was associated with increased knowledge score. Additionally, behavior score was higher among participants in urban areas than those in rural areas. We found statistically significant positive correlations between the four factors. Levels of knowledge, awareness, practice and behavior about heat waves were high in our sample. Several socio-demographic variables affect participants’ knowledge, awareness, practice and behavior concerning heat waves.

Swarm intelligence (SI) methods are nature-inspired metaheuristics for global optimization that exploit a coordinated stochastic search strategy by a group of agents. Particle Swarm Optimization (PSO) is an established SI method that has been applied successfully to the optimization of rugged high-dimensional likelihood functions, a problem that presents the main bottleneck across a variety of gravitational wave (GW) data analysis challenges. We present results from a first application of PSO to one of the most difficult of these challenges, namely, the search for Extreme Mass Ratio Inspiral (EMRI) in data from future spaceborne GW detectors such as LISA, Taiji, or Tianqin. We use the standard Generalized Likelihood Ratio Test formalism, with minimal use of restrictive approximations, to search 6 months of simulated LISA data and quantify the search depth, in signal-to-noise ratio (SNR), and breadth, in the ranges of the EMRI parameters, that PSO can handle. Our results demonstrate that a PSO-based EMRI search is successful over a search region that is in the ballpark of the one that current hierarchical schemes can identify. Directions for future improvements, including computational bottlenecks to be overcome, are identified.

On February 24, 2022 Russia started the full-scale invasion of Ukraine, which created an unprecedented number of refugees. To estimate the influence of this humanitarian disaster on the COVID-19 pandemic dynamics, the averaged daily numbers of cases and reproduction numbers in Ukraine, the UK, Poland, Germany, the Republic of Moldova, and in the whole world were calculated for the period February-April 2022. The registered numbers of cases were compared with ones calculated with the use of the generalized SIR-model and corresponding parameter identification procedure for the previous epidemic waves in Ukraine, Poland, Germany, and the world. Since before February 24, 2022 the estimation of the number of infectious persons per capita in Ukraine 3.6 times exceeded the global figure, the increase of the number the new cases and the pandemic duration was expected. In March 2022 the increase of the averaged number of new cases in the UK, Germany, and worldwide was visible. A simple formula to estimate the effective reproduction number based on the smoothed accumulated numbers of cases is proposed. The results of calculations agree with the figures presented by John Hopkins University and demonstrate a short-term growth of the reproduction number in the UK, Poland, Germany, Moldova, and worldwide in March 2022.

Reservoir computing (RC) systems can efficiently forecast chaotic time series using nonlinear dynamical properties of an artificial neural network of random connections. The versatility of RC systems has motivated further research on both hardware counterparts of traditional RC algorithms and more efficient RC-like schemes. Inspired by the nonlinear processes in a living biological brain and using solitary waves excited on the surface of a flowing liquid film, in this paper we experimentally validate a physical RC system that substitutes the effect of randomness for a nonlinear transformation of input data. Carrying out all operations using a microcontroller with a minimal computational power, we demonstrate that the so-designed RC system serves as a technically simple hardware counterpart to the `next-generation’ improvement of the traditional RC algorithm.

Power sources that can consistently deliver high levels of energy over extended periods are crucial for various space applications. Among the many methods of energy generation, direct heat-to-electricity conversion without intermediate steps or moving components shows particular promise but also presents significant challenges. The aim of this research is to address these challenges by enhancing the energy efficiency of thermionic conversion, which transforms thermal energy into electrical energy, through the development and utilization of a novel class of emission nanomaterials known as multilayer carbyne-enriched 3D-shaped nano-interfaces. By manipulating the topological, physicochemical, and functional characteristics of these interfaces, we seek to optimize their thermionic conversion capabilities. Building on the recent discovery of collective atomic vibrations called phonon waves within transition domains of multilayer nanostructures, we have devised a new approach to enhance the efficiency of thermionic energy converters. This involves unlocking the predictive functionality of 2D-ordered linear-chain carbon-based multilayer emitters through the excitation and fine-tuning of collective atomic vibrations and nanoarchitecture. To achieve this, we propose employing a combination of techniques that leverage interface effects, enable phonon wave propagation, facilitate energy exchange, and capitalize on synergistic effects offered by the multilayer nano-enhanced interfaces. The resulting devices for thermionic energy conversion have the potential to significantly surpass the efficiency of existing plasma thermionic converters by several orders of magnitude. Moreover, these electricity-generating sources based on thermionic conversion represent fundamental options for the advancement of Lunar and Martian research missions, opening up possibilities for sustainable energy production in extraterrestrial environments.

We propose a toy model of a spherical universe made up of an exotic dark gas with temperature $T$ in thermal equilibrium with a black-body. Each particle of this exotic gas mimics a kind of particle of dark energy. So, each dark particle occupies a very small area of space so-called Planck area $L_p^{2}$, which represents the minimum area of the whole space-time given by the spherical surface with area $4\pi R_H^2$, where $R_H$ is the Hubble radius. We realize that such spherical surface is the surface of the black-body for representing the dark universe as if it were the surface of an expanding balloon. Thus, we are able to derive the law of universal gravitation, thus leading us to understand the cosmological anti-gravity. We estimate the tiny order of magnitude of the cosmological constant and the acceleration of expansion of the dark sphere. In this toy model, as the dark universe can be thought of as a large black body, when we obtain its power and frequency of emission of radiation, we find very low values. We conclude that such radiation and frequency of the black body made up of dark energy is a background gravitational wave with very low frequency in the order of $\sim 10^{-17}$Hz due to the slight stretching of the fabric of space-time.

: The article presents a brief review of cooling systems of various temperature levels (from 0.1 K to 230 K) for radio astronomical receivers of photonics and electronics. The features of various levels of cooling and the requirements for the design of the cooling system are considered in detail, as well as approaches to designing interfaces for cooled receivers: vacuum, cryogenic, electrical, mechanical, optical, and others required for the effective operation of the receiver,. The presented approaches to design are illustrated by a series of joint developments of the authors carried out over the past 45 years, including those produced last year.

In the rapidly evolving landscape of wireless communication, each successive generation of networks has achieved significant technological leaps, profoundly transforming the way we connect and interact. From the analog simplicity of 1G to the digital prowess of 5G, the journey of mobile networks has been marked by constant innovation and escalating demands for faster, more reliable, and more efficient communication systems. As 5G becomes a global reality, laying the foundation for an interconnected world, the quest for even more advanced networks leads us to the threshold of the sixth-generation (6G) era. This paper presents a hierarchical exploration of 6G networks, poised at the forefront of the next revolution in mobile wireless technology. This study delves into the technological advancements that underpin the need for 6G, examining its key features, benefits, and the key enabling technologies. We dissect the intricacies of cutting-edge innovations like terahertz communication, ultra-massive MIMO, artificial intelligence (AI), machine learning, quantum communication, and re-configurable intelligent surfaces. Through a meticulous analysis, we evaluate the strengths, weaknesses, and state-of-the-art research in these areas, offering a wider view of the current progress and potential applications of 6G networks. Central to our discussion is the transformative role of AI in shaping the future of 6G networks. By integrating AI and machine learning, 6G networks are expected to offer unprecedented capabilities, from enhanced mobile broadband to groundbreaking applications in areas like smart cities and autonomous systems. This integration heralds a new era of intelligent, self-optimizing networks that promise to redefine the parameters of connectivity and digital interaction. This paper also addresses critical challenges in the deployment of 6G, from technological hurdles to regulatory concerns, providing a holistic assessment of potential barriers. By highlighting the interplay between 6G and AI technologies, this study not only maps out the current landscape but also lights the path forward in this rapidly evolving domain. This paper aims to be a cornerstone resource, providing essential insights, addressing unresolved research questions, and stimulating further investigation into the multifaceted realm of 6G networks. By highlighting the synergy between 6G and AI(Artificial Intelligence) technologies, we aim to illuminate the path forward in this rapidly evolving field.

River bed materials serve multiple environmental functions as a habitat for aquatic invertebrates and fishes. At the same time, the particle size of the bed material reflects the tractive force of the flow regime in a flood and provides useful information for flood control. The traditional river bed particle size surveys, such as sieving, require time and labor to investigate river bed materials. The authors proposed a method to classify aerial images taken by unmanned aerial vehicle (UAV) using convolutional neural networks (CNN), our previous study showed that terrestrial riverbed material could be classified with high accuracy. In this study, we attempted to classify riverbed materials distributed in shallow waters where the bottom can be seen from UAVs. After training the CNN to classify the images with the same grain size as being in the same class even if the surface flow types taken overlapping the riverbed material were different, the total accuracy reached 90.3%. Moreover, the proposed method was applied to the wide-ranging area to determine the distribution of the particle size. In parallel, the microtopography was surveyed using Lidar-UAV, and the relationship between the microtopography and particle size distribution was discussed. In the steep section, coarse particles were distributed and formed a rapid. Fine particles were deposited on the upstream side of those rapids, where the slope had become gentler due to the damming. There was good agreement between the microtopographical trends and the grain size distribution.

We introduce quantum spatio-temporal dynamics (QSD) as modeled by the Nexus Paradigm (NP) of quantum gravity to resolve the problem of energy- momentum localization in a gravitational field. Currently, the gravitational field as described using the language of geometry modeled under General Relativity (GR) fails to provide a generally accepted definition of energy-momentum. Attempts at resolving this problem using geometric methods have resulted in various energy-momentum complexes whose physical meaning remain dubious since the resulting complexes are non-tensorial under a general coordinate transformation. In QSD, the tangential manifold is the affine connection field in which energy-momentum localization is readily defined. We also discover that the positive mass condition is a natural consequence of quantization and that dark energy is a Higgs like field with negative energy density everywhere. Finally, energy-momentum localization in quantum gravity shows that a free falling object will experience large vacuum fluctuations (uncertainties in location) in strong gravity than in weak gravity and that the amplitudes of these oscillations defines the energy of the free falling object.

A question of physical importance is whether finite-energy spatiotemporally localized (i.e., pulsed) generalizations of monochromatic accelerating Airy beams are feasible. For luminal solutions, this question has been answered affirmatively by Saari, Valdmann, Piksarv, Valta-Lukner and Saari, and Kaganovsky and Heyman within the framework of the paraxial geometry. The time-diffraction technique introduced by Porras recently has been motivated by Besieris and Shaarawi in terms of the Lorentz invariance of the equation governing the narrow angular spectrum and narrowband temporal spectrum paraxial approximation and has been used to derive finite-energy spatiotemporally confined subluminal, luminal, and superluminal Airy wave packets. The goal in this article is to provide exact finite-energy broadband spatiotemporally localized Airy solutions (a) to the scalar wave equation in free space; (b) in a dielectric medium moving at its phase velocity; (c) in a lossless second order temporally dispersive medium.

The possibility of a shock wave recovery at a discrete closed interface with a heated gas has been investigated. A two-dimensional model applied to conditions of optical discharges featuring spherical, elliptical, and drop-like configurations demonstrated that non-symmetry in the shock refraction contributes to the specific mechanism of recovery other than simply its compensation. Even though the full restoration of the hypersonic flow state doesn’t occur in a strict sense of it, clear reverse changes toward the initial shape of the shock front eventually take place, thus creating an appearance of a full recovery seen in experiments. From analysis for different interfaces symmetries, the factors determining the recovery dynamics are identified. The results are directly applicable to the problem of energy deposition into a hypersonic flow, however it can be useful anywhere else where the flow modifications following the interaction are important. The dimensionless form of the equations allows applications on any scale other than that demonstrated for the optical discharges.

Ultrasonic feedback energy is affected by the variety, planting and growth state of crops, it is difficult to fine application in precision agriculture systems. To this end, an ultrasonic sensor was mounted in a spray boom height detection system. Winter wheat was used as the test object to obtain feedback energy values for the spray boom height from the top of the wheat in the field during six critical growth stages: the standing stage, jointing stage, booting stage, heading stage, filling stage and maturity stage. The relationship between the actual value of the height from the spray boom to the top of wheat (Habw) and the detected value of the height from the spray boom to the top of wheat (Hdbw) was analyzed. A spray boom height detection model based on the ultrasonic sensor during the full growth cycle of wheat was determined. Field validation tests showed that the applicability of the spray boom height detection distance (Dd) of the spray boom height detection model proposed in the present study was 450 mm~950 mm. Within the applicable Dd range, the detection error of the detection model was ≤5 cm during the full growth cycle. This study provides an ultrasonic detection model construction method, which improves the reliability and accuracy of ultrasonic boom height detection for different wheat growth stages.

To obtain a better estimation frequency band for source bearing estimation, source bearing estimation experiments using an ice-mounted geophone were performed at three sites on the Arctic ice cap. By transforming to the frequency domain, errors of the bearing estimation in a number of frequency bands within 1000 Hz and the horizontal peak displacements received by the geophone in the corresponding frequency bands were obtained. After comparing the variation of errors to the peak displacements in the same frequency band, it is found that the errors are related to the peak displacements, and higher peak displacement values mean smaller errors. When the incident angle of the acoustic source and the ice thickness meet certain conditions, some modes of the Lamb waves of the ice plate are excited, the peak displacements at the same frequency band are increased, the errors of bearing estimation are reduced, and the effective frequency band for bearing estimation is broadened. These results provide some new ideas for the bearing estimation of acoustic sources beneath Arctic ice.

We present multi-sensor measurements from satellites, unmanned aerial vehicle, marine radar, thermal profilers and repeated conductivity-temperature-depth casts made in the Kara Gates strait connecting the Barents and the Kara Seas during spring tide in August 2021. Analysis of the field data during an 18-hour period from four stations evidence that a complex sill in the Kara Gates is the site of regular production of intense large-amplitude nonlinear internal waves. Satellite data show a presence of a relatively warm northeastward surface current from the Barents Sea toward the Kara Sea attaining 0.8-0.9 m/s. Triangle-shaped measurements of three thermal profilers revealed pronounced vertical thermocline oscillations up to 40 m associated with propagation of short-period nonlinear internal waves of depression generated by stratified flow passing a system of shallow sills in the strait. The most intense waves were recorded during the ebb tide slackening and reversal when the background flow was predominantly supercritical. Observed internal waves had wavelength of ~100 m and travelled northeastward with phase speeds of 0.8-0.9 m/s. The total internal wave energy per unit crest length for the largest waves was estimated to be equal to 1.0-1.8 MJ/m.

The coastal zone faces an ever-growing risk associated with climate-driven change, including sea level rise and increased frequency of extreme natural hazards. Coastal processes are governed by the dynamic ocean and atmospheric factors with constantly changing conditions. Often the location and dynamism of coastal regions makes them a formidable environment to adequately study with in-situ methods. Remote sensing methods offer an alternative to in-situ monitoring. In this study we use Ice, Cloud, and land Elevation Satellite-2 (ICESat-2) to make measurements of basic wave parameters and wave directionality in the Hawaiian Islands and North Carolina, USA. ICESat-2 has existing Level-3a data products, Ocean Surface Height (ATL12) and Inland Water Elevation (ATL13), providing some wave and ocean surface elevation data. ATL12 provides sparse global average measurements of the sea surface elevation, slope, and roughness along ICESat-2 tracks and ATL13 provides wave metrics at variable length scales out to ~7 km from the coast and does not maintain the 0.7m along-track resolution of the primary Level-2 data product (ATL03). Our goal was to leverage the full resolution data available in ATL03 to generate wave metrics out from shore up to ~25 km. Using a combination of statistical and signal processing methods we can use ICESat-2 to generate basic wave metrics, including significant wave heights with an accuracy of ±0.5m. In some profiles we can identify wave shoaling, which could be used to infer bathymetry. In areas with complex wave dynamics, the nature of how ICESat-2 measures elevations (parallel laser altimetry beams) can make extracting some wave parameters (e.g., wavelength and directionality) more challenging. These wave metrics can provide important data in support of validating wave and tidal models and may also prove useful in ICESat-2 bathymetric corrections and satellite derived bathymetry.

Radio astronomical observations at millimeter and submillimeter wavelengths are a very important tool of astrophysical research. However, there is a huge area in the northern Eurasia, including the whole Russian territory, which lacks sufficiently large radio telescopes effectively operating at these wavelengths. In this review we describe our long-term efforts to find suitable sites for such radio telescopes in this area, that is, sites with good atmospheric transparency at millimeter and submillimeter waves. We describe methods and instruments used for measurements and evaluations of the atmospheric opacity. They include special radiometric systems, which are used for estimations of the atmospheric opacity from the sky brightness measurements. Evaluation of the precipitable water vapor from such measurements by the artificial neural network is discussed. Alternative approaches use global atmospheric models and signals of the Global Navigation Satellite Systems. To date, a long-term radiometric monitoring has been performed at several candidate sites and atmospheric conditions for many sites have been evaluated using global atmospheric models. Several sites with the best atmospheric transparency at millimeter and submillimeter wavelengths have been selected. They can be effectively used for astronomical observations at least in the major atmospheric transparency windows at 1.3 mm and 0.85 mm. These results can be also used for space communications and radar systems.

Localized turbulence is common in geophysical flows, where the roles of rotation and stratification are paramount. In this study, we investigate the evolution of a stratified turbulent cloud under rotation. Recognizing that a turbulent cloud is composed of vortices of varying scales and shapes, we start our investigation with a single eddy. Compared to an eddy under pure rotation, the stratified eddy shows the physical manifestation of a known potential vorticity mode, appearing as a static stable vortex. In addition, the expected shift from inertial waves to inertial-gravity waves is observed. In our numerical simulations of the turbulent cloud, carried out at a constant Rossby number over a range of Froude numbers, stratification causes columnar structures to deviate from vertical alignment. This deviation increases with increasing stratification, slowing the expansion rate of the cloud. The observed characteristics of these columnar structures are consistent with the predictions of linear theory, particularly in their tilt angles and vertical growth rates, suggesting a significant influence of inertial-gravity waves. Using Lagrangian particle tracking, we have identified regions where wave activity dominates over turbulence. In scenarios of milder stratification, these inertial-gravity waves are responsible for a significant energy transfer away from the turbulent cloud, a phenomenon that attenuates with increasing stratification.

This paper describes the design and implementation of an ultrasonic non-contact air-coupled technique (UNCACT) using antisymmetric Lamb waves (ALW) for NDT assessment in novel composite sandwich plates of the car body shell. This technique is complemented with a C-Scan image implementation using this kind of guided waves. The finite element method using Comsol 6.1 is developed for the interpretation of the several wave modes presented in the experiments, including the ALW mode. The phase velocity method (PVM) is applied for the verification of the ALW mode in the portion of the RF signal necessary in the C-Scan image.

The cost effective design of tidal turbines requires a good estimation of the loading cycles and their extrema that are related to the unsteady fluctuations of the current velocity. Apart from the ambient turbulence, the main source of velocity fluctuations is the presence of surface waves. In the present study, we analyse the effect of waves propagating against the current on the performance and the loads of a twin vertical axis tidal turbine by an experimental approach at a 1/20 scale. Overall, the results show little or no effect of the waves on the average power and loads compared to the condition with current only, but a significant impact on their standard deviation that rises linearly with the waves amplitude. The drag, lift and pitching moment show extended ranges up to 7.5 times higher and extreme values exceedance by 60 to 100 % with irregular waves compared to the condition without waves. Those load and power fluctuation increase are fully due to the presence of waves as the coherence function between the rotor torque or the loads and the velocity spectra exceed 0.5 on the whole wave frequency bandwidth. The results also reveal a rotational sampling of the waves by the rotors that had also been observed on horizontal axis turbines. From a structural design point of view, the authors recommand to conduct tests in irregular wave conditions as the loads range and extreme values are 1.5 to 2 times higher than those encountered with regular waves of the same significant height and period.

This article is a commentary on the publication Guo J, Hai H, Ma Y. Application of extracorporeal shock wave therapy in nervous system diseases: A review. Front Neurol. (2022) 13:963849. doi: 10.3389/fneur.2022.963849 (1). In the opinion of the authors of this commentary the information provided in the Section "Principles of ESWT" in (1) is partly incorrect and misleading. This is due to the fact that important, published knowledge regarding focused extracorporeal shock wave therapy (fESWT) and radial extracorporeal shock wave therapy (rESWT) was disregarded in (1).

When two black holes form a binary system, each black hole observes an event horizon and a curved distorted space-time region around the other black hole. In this space-time, two such regions are formed, and another black hole forms in the second region from the initial black hole, which may be termed the “image” of the first black hole. The same event occurs for the other black hole also, and an extra image of it is formed. In these conditions, the energy of the system divides between the two black holes and their images. These four new black holes that are formed interact with each other again and produce new horizons and new distorted regions. Each black hole produces an image of all the other black holes and detects the background of six black holes instead of three. Consequently, for four black holes, 24 new black holes arise. The energy of the system will be divided amongst all 24 black holes. This story continues and black holes interact with one another and produce new images. Finally, very light black holes are formed each of which is so weak that it cannot produce strong distortions of space-time. The radiated gravitational waves from these weak black holes could be detected by LIGO as well as the signature of these binary black holes. However, detected waves are only a part of very strong gravitational waves. Each time a part of these waves escapes from the system and reaches the earth, they may be regarded as emitted waves from a new binary black hole. The time between radiated signals decreases, and it may be interpreted that a new supermassive binary black hole is radiating. If radiated signals combine, an explosion of the very strong binary system could be detected.

The elastic wave equation with the seismic tensorial force is solved in a homogeneous and isotropic medium (the Earth). Spherical-shell waves are obtained, which are associated to the primary P and S seismic waves. It is shown that these waves produce secondary waves with sources on the plane surface of a half-space, which have the form of abrupt walls with a long tail, propagating in the interior and on the surface of the half-space. These secondary waves are associated to the seismic mainshock. The results, previously reported, are re-derived by using Fourier transformations and specific regularization procedures. The relevance of this seismic motion for the ground motion, the seismographs' recordings and the effect of the inhomogeneities in the medium are discussed.

Recent evidence obtained in murine atrial cardiomyocytes suggests that the behavior of tubulin, a constituent of microtubules, is influenced by audible sounds. In the present study, the sequence and the structure of murine and human tubulins were compared with those of human TMC1 (Transmembrane channel-like protein 1), a sound-sensitive protein that is responsible for forming the pore of mechanosensory transduction channels in the hair cells of the inner ear of vertebrates, and with those of bacterial FtsZ (Filamenting temperature-sensitive mutant Z), a bacterial protein homologous to tubulin. The results show that mouse and human alpha-tubulin are 100% identical, whereas sequence homology of human TMC1 and human tubulin alpha 1A chain is scarce, with only 17.31% identity. A higher degree of similarity was observed in the presence of aromatic amino acids as well as in the propensity to form alpha-helices. Based on these results, it is hypothesized that the response of tubulin to audible sounds is mediated by the external alpha-helices as it occurs in TMC1. The sequence homology of human TMC1 and FtsZ from Lactobacillus johnsonii, is moderate with 23.40% identity, however higher than that between TMC1 and tubulin. The overall presence of aromatic amino acids in FtsZ is scarce, but helix propensity is significant. These results are discussed in the context of Orch OR, a theory that postulates that consciousness emerges from quantum computations occurring in microtubules of neurons via information processing mediated by aromatic amino acids of tubulin.

This study investigates the ionospheric variations resulting from thunderstorms that occurred between 00:00 UTC and 08:00 UTC on November 10, 2018, in the central region of Argentina, site of the RELAMPAGO-CACTI Project (Remote sensing of Electrification, Lightning, and Mesoscale/microscale Processes with Adaptive Ground Observations; Clouds, Aerosols, and Complex Terrain Interactions). The data used were the Total Electron Content (TEC), which was computed from Global Navigation Satellite System (GNSS) measurements provided by the Argentinian Continuous Satellite Monitoring Network (RAMSAC by its Spanish acronym) stations and the atmospheric electrical activity data that were provided by the Earth Networks Total Lightning Network (ENTLN). We observed that the generated disturbances have periods less than or equal to 100 minutes and peak-to-peak DVTEC amplitude values reaching up to 1.35 TECU (1 Total electron content unit =1016electrons/m2). We also noted that these atmospheric gravity waves, which show the highest peak-to-peak amplitudes, occur during periods of intense lightning activity. Finally, we found that for a day with Atmospheric Electrical Activity (AEA), the peak-to-peak amplitudes of the waves are approximately 2.91 times greater than the peak-to-peak amplitudes of a day without AEA.

(1) Background: Since the onset of the SARS-CoV-2 pandemic, seven epidemic waves have been described in Spain. Our objective was to study mortality and severity, and associated factors in our hospitalized patients; (2) Method: Retrospective cohort study was conducted on COVID-19 patients admitted to the Hospital de Fuenlabrada (Madrid, Spain) from the beginning of the pandemic until December 31, 2022; (3) Results: A total of 5,510 admissions for COVID-19 were recorded. First wave accounted for 1,823 (33%) and exhibited the highest proportion of severe patients (lowest mean oxygen saturation, 88.2%; elevated levels of CRP, IL-6, D-dimer and ferri-tin), but a below-average percentage of intubated patients (5% vs. 6.5%). Overall mortality rate was 10.3%, higher during the first wave (11.5%) and the two winter waves (third: 11.3%, sixth: 12%), although the first wave represented 39% of the total. Variables associated with mortality were age (OR 1.08,1.07-1.09), need for high-flow oxygen (OR 6.10,4.94-7.52), oncological disease (OR 1.88,1.53-2.60), dementia (OR 1.82,1.2-2.75), Charlson index (OR 1.38,1.31-1.47), and maxi-mum IL-6 levels (OR 1.001,1.000-1.001); (4) Conclusions: Variables associated with mortality in-cluded age, comorbidity, respiratory failure, and inflammation. Differences on baseline charac-teristics of patients admitted explained differences on mortality in each wave

In this investigation, we explore the existence and intriguing features of matter wave positons in a nonautonomous one-dimensional Bose-Einstein condensate (BEC) system with attractive interatomic interactions. We focus on the Gross-Pitaevskii (GP) equation/nonlinear Schrödinger (NLS)-type equation with time-modulated nonlinearity and trap potential, governing nonlinear wave propagation in the BEC. Our approach involves constructing second- and third-order matter wave positons using a similarity transformation technique. We also identify the constraints on the time-modulated system parameters that give rise to these nonlinear localized profiles. The study considers three distinct forms of modulated nonlinearities: (i) kink-like, (ii) localized or -like, and (iii) periodic. By varying the parameters associated with the nonlinearity strengths, we observe a rich variety of evolution behaviors in the matter wave positon profiles. These behaviors include stretching, curving, oscillating, breathing, collapsing, amplification, and suppression. Our comprehensive studies shed light on the intricate dynamics of matter wave positons in BECs, providing valuable insights into their behavior and characteristics in the presence of time-modulated nonlinearity and trap potential effects.

Volumetric modification of transparent materials by femtosecond laser pulses is successfully used in a wide range of practical applications. The level of modification is determined by the locally absorbed energy density, which depends on numerous factors. In this work, it is shown experimentally and theoretically that, in a certain range of laser pulse energies, the peak of absorption of laser radiation for doughnut-shaped (DS) pulses is several times higher than for Gaussian ones. This makes the DS pulses very attractive for material modification and direct laser writing applications. Details of the interaction of laser pulses of Gaussian and doughnut shapes with fused silica obtained by numerical simulations are presented for different pulse energies and compared with the experimentally obtained data. The effect of absorbed energy delocalization with increasing laser pulse energy is demonstrated for both beam shapes while, at relatively low pulse energies, the DS beam geometry provides a stronger local absorption compared to Gaussian one. Implications of a DS pulse action on post-irradiation material evolution are discussed based on thermoelastoplastic modeling.

The purpose of this work is to compare two fracture prediction models with real-world data. The pure Artificial Neural Network (ANN) model emphasizes regression analysis, while the hybrid model (SVM-ANN) focuses on the combination of regression and classification analysis or Support Vector Machine. The results were subsequently tested against logging data by combining the Machine Learning approach with advanced logging tools. In this context, we used electrical image logs and the dipole acoustic tool which together allowed the distinction of 404 open fractures and 231 closed fractures and, consequently the estimation of fracture porosity. The results are then fed into two machine-learning algorithms. Pure Artificial Neural Networks and hybrid models are used to establish comprehensive results, which are subsequently tested to check the accuracy of the models. The outputs obtained from the two methods demonstrate that the hybridized model has a lower Root Mean Square Error (RMSE) than pure ANN. The results of our approach strongly suggest that incorporating hybridized machine learning algorithms in fracture porosity estimations can contribute to the development of more trustworthy static reservoir models in simulation programs. Finally, the combination of Machine Learning (ML) and well-log analysis do permit reliable estimation of fracture porosity in the Ahnet field in Algeria, where, in many places, advanced logging data is absent and costly.

In order to better understand the extent to which global climate variability is linked to the frequency and intensity of heat waves and overall changes in temperature throughout the United States (US), correlations between long-term monthly mean, minimum, and maximum temperatures measured at sites throughout the contiguous US and low-frequency variability of multiple climate indices (CIs) are analyzed over the period 1948 to 2018 using correlation analysis. The Pearson’s correlation coefficient is used to assess correlation strength, while Leave-One-Out Cross-Validation and a bootstrapping technique (p-value) are used to address potential serial and spurious correlation and assess the significance of each correlation. Three parameters defined the sliding windows over which surface temperature and CI values were averaged: window size, lag time between the temperature and CI windows, and the beginning month of the temperature window. A 60-month sliding window size and 0 lag time resulted in the strongest correlations overall; beginning months were optimized on an individual site basis. Strong (r >= 0.60) and significant (p-value <= 0.05) correlations were identified. The Western Hemisphere Warm Pool (WHWP) and El Niño/Southern Oscillation (ENSO) exhibited the strongest links to temperatures in the western US, tropical Atlantic sea surface temperatures to temperatures in the central US, the WHWP to temperatures throughout much of the eastern US, and atmospheric patterns over the northern Atlantic to temperatures in the Northeast and Southeast. The final results were compared to results from previous studies focused on precipitation and coastal sea levels. Regional consistency was found regarding links between the northern Atlantic and overall weather and coastal sea levels in the Northeast and Southeast as well as on weather in the upper Midwest. Though the MJO and WHWP revealed dominant links with precipitation and temperature, respectively, throughout the West, ENSO revealed consistent links to sea levels and surface temperatures along the West Coast. These results help focus future research regarding specific mechanisms of climate variability that appear the exhibit strong links to US regional weather and sea level variability and prediction.

We propose an experimental method for the unidirectional excitation of spin waves. By structuring Au nanowires arrays within a coplanar waveguide onto a thin yttrium iron garnet (YIG) film, we observe a chiral coupling between the excitation field geometry of the nanowires grating and several well-resolved propagating magnon modes. We report a propagating spin wave spectroscopy study with unprecedented spectral definition, wavelengths down to 130 nm and attenuation lengths well above the 100 μm over the 20 GHz frequency band. The proposed experiment paves the way for future non-reciprocal magnonic devices.

Lamb wave-based structural health monitoring is widely acknowledged as a reliable 11 method for damage identification, classification, localization and quantification. However, due to 12 the complexity of Lamb wave signals, especially after interacting with structural components and 13 defects, interpreting these waves and extracting useful information about the structure's health is 14 still a major challenge. However, deep learning-based strategy offers a great opportunity to address 15 such challenges as the algorithm can operate directly on raw discrete time-domain signals. Unlike 16 traditional methods, which often require careful feature engineering and preprocessing, deep learn-17 ing can automatically extract relevant features from the raw data. This paper proposes an autoen-18 coder based on a bidirectional long short-term memory network with maximal overlap discrete 19 wavelet transform layer to detect the signal anomaly and determine the location of the damage in 20 the composite structure. This approach has the potential to greatly enhance our ability to detect and 21 locate structural damage in composite structures, thereby increasing safety and efficiency.

We investigate the evolution of gravitational waves through discontinuous evolution (transition) of the Hubble expansion rate H(z) at a sudden cosmological singularity which may be due to a transition of the value of the gravitational constant. We find the evolution of the scale factor and the gravitational wave waveform through the singularity by imposing the proper boundary conditions. We also use existing cosmological data and mock data of future gravitational wave experiments (the ET) to impose current and anticipated constraints on the magnitude of such a transition. We show that mock data of the Einstein Telescope can reduce the uncertainties by up to a factor of 3 depending on the cosmological parameter considered.

The dispersion properties of surface plasmon polaritons during propagation on metal wires with a dielectric coating in the terahertz frequency range are investigated theoretically. An analytical expression is obtained for a pulsed electric field from the solution of Maxwell equations taking into account high-order dispersion terms. The effect of the dielectric coating on the distortion of the pulse shape is analyzed. Unlike uncoated wire, the propagation of a surface plasmon pulses along a coated wire is highly dispersive. It is shown that the coating leads to the appearance of a long-chirped signal with a propagation of only a few millimeters, i.e. when a terahertz pulse propagates along a coated wire, it acquires a long oscillatory tail, the frequency of which depends on time.

Background: The manifestations, severity, and mortality of COVID-19 are considered to be associated with the changes in various hematological parameters and in immunity. Associations of immunoglobulin G antibodies against severe acute respiratory syndrome-linked coronavirus (IgG-SARS)-positive status with cardiac function and hematological and biochemical parameters in apparently health subjects are poorly understood. Methods: The present cross-sectional study included 307 healthy volunteers (24-69 years of age; 44.8±8.6 years; 80.4% men) and was initiated in 2019 before the COVID-19 pandemic. COVID-19 episodes were confirmed by detection of IgG-SARS against SARS-CoV-2 S1 RBD to reveal 70 IgG-SARS-positive and 237 negative participants. Numerous ultrasound characteristics were assessed by echocardiography, and 15 hematological and biochemical parameters were assayed in the blood. Descriptive and comparative analysis was based on the IgG-SARS status of the participants. Results: The left ventricular mass index, mitral ratio of peak early to late diastolic filling velocity or flow velocity across the mitral valve, and deceleration time of early mitral inflow were decreased (P<0.05) in IgG-SARS-positive participants versus those in IgG-SARS-negative participants according to multivariate logistic regression analysis. Erythrocyte sedimentation rate and platelet count were slightly increased, and blood hemoglobin was decreased in IgG-SARS-positive participants compared with those in IgG-SARS-negative participants. Conclusions: LV filling, inflammation, blood coagulation, and hemoglobin appear to be influenced by COVID-19 infection in healthy participants. These observations contribute to the development of a population recovery strategy after the episodes of COVID-19.

Statistical based reconstruction methods and signal processing tooling techniques are implemented and used to detect delaminations or debondings within composite items. From literature it appears that, although a single procedure for the estimation of the structural health is a fast solution, a multiple analysis based on different reconstruction methods or different damage parameters could provide more detailed information about the location and the severity of possible failures. This work discusses the advantage of using cross-correlation analysis in a data-driven approach based on ultrasonic guided waves (GW) tomographic technique and piezoelectrics (PWAS) in pitch-catch configuration. In this sense, this work evidences an improvement in damage detection when the cross-correlation is included as part of the GW-based system for damage assessment approach. The specimens used as test structures to demonstrate the validity of the methodology derive from an aircraft wing test article where damages are specified as skin delamination produced by low energy impact.

In this paper, the feasibility of automated and accurate in vivo measurements of vascular parameters continuously and non-invasively using ultrasound sensor is presented. Vascular parameters such as pulse wave velocity (PWV), blood pressure (BP), arterial compliance (AC) and stiffness index (SI) are affluent indicators of cardiovascular disorders and needs to be monitored non-invasively and continuously during surgeries and follow-up procedures. Cuff based or invasive catheter techniques are considered as gold standard to measure BP and are fed manually to compute AC and SI which employ imaging algorithms. In this context, a Continuous and Non-Invasive Vascular Stiffness and Arterial Compliance Screener (CaNVAS) is developed to measure said parameters continuously and non-invasively using ultrasound sensor. Acoustic waves of 5 MHz (2.2 – 10 MHz) are driven through target arterial walls, reflected echoes captured, pre-processed and frequency shift is used to calculate PWV. It is observed that PWV measured using CaNVAS varies exponentially with BP values obtained from sphygmomanometer (BPMR-120) and this relationship is used to compute instantaneous values of BP. The proposed device is validated by performing measurements on 250 subjects in pre and post exercise conditions and found to have 95% accuracy and an average of 12.5% coefficient of variation.

We consider the propagation of electromagnetic waves in the Friedman – Lemaître – Robertson – Walker metric. The exact solutions for plane and spherical wave are written down. The corresponding redshift, amplitude change, and dispersion are discussed. We also speculate about the connection of the electromagnetic wave equation to the Klein–Gordon equation.

This work deals with the evaluation of adhesive single-lap joints using ultrasonic guided waves. An adhesive bonded lap joint can be modelled as a three-layer system made up of two adherents and an adhesive. The propagation of guided waves in the joint is developed from matrix formulations. The behavior of the different guided wave modes that propagate in the bonded region is characterized and it is found that their relative amplitudes can be estimated based on the properties of the incoming wave that propagates in the non-bonded region. It was verified that the excitation of these modes is ruled by the degree in which the shapes of both modes match each other. A 3D simulation of two aluminium bonded plates using 500 kHz ultrasonic transducers in a pitch and catch configuration was implemented using the Matlab k-Wave toolbox. Scattering effects due to some produced defects located in the bond line of the lap joints were simulated. Experimental setup with some artificial defects produced in the aluminum joints were used in order to compare with the simulated. Qualitative agreement was observed for the two approaches. The observed deviation can be due to the different characteristics of the experimental and simulated defects.

Wave buoy measurements were carried out near the north-eastern Black Sea coast at the natural reserve Utrish in 2020-2021. In total, about 11 months of data records were collected during two stages of the experiment at 600 and 1500 meters offshore and depths of 18 and 42 meters. The measured waves propagate almost exclusively from the seaward directions. Generally, the waves do not follow the local wind directions, thus, implying a mixed sea state. Nevertheless, dimensionless wave heights and periods appears to be quite close to the previously established empirical laws for the wind-driven seas. The results of the wave turbulence theory are applied for estimates of spectral energy fluxes and their correspondence to the energy flux from the turbulent wind pulsations. These estimates are consistent with today's understanding of wind-wave interaction. It is shown that the main fraction of the wind energy flux goes to the direct Kolmogorov-Zakharov cascade to high wave frequencies and then to dissipation in small scales. Less than 1% of the wind energy flux is directed to low frequency band (the so-called inverse Kolmogorov-Zakharov cascade), thus, providing wave energy growth.

The formation and localization of sporadic E(Es) layers predicted by the ions vertical drift velocity and its vertical change in the lower thermosphere during nighttime are shown analytically and by numerical simulations. The consideration of existence of a minimum negative value of the vertical change of the ions vertical drift velocity as a necessary condition of formation of Es layer and determining ions convergence rate into this layer, is extended in case of the presence of vertical wind. Upward vertical wind can shift the convergence regions upward, while downward vertical wind shift them downward, unlike the cases of presence of only meridional and zonal winds. It also changes the ion convergence rate compared to the one with just a horizontal wind. It is shown for the first time that the upward constant wind also causes the convergence of ions with maximum rate in the region where the ion-neutral collision frequency is equal to their cyclotron frequency. While demonstrating the presented theory by numerical simulations, HWM14 data is used for the meridional and zonal wind velocity profiles and the presence of its vertical component is assumed. In this case, in addition to the estimated ion drift velocity and its vertical changes, their initial distribution and ambipolar diffusion also determine the development of ion convergence/divergence processes. For small magnitude of vertical wind velocity, its significant influence on the ions/electrons behavior is demonstrated, which shows the importance of both tidal wind and wind changes caused by the propagation of atmospheric gravity waves on the formation of the Es layer. In this theoretical research it is shown that the realistic profile of the wind velocity, which takes into account the vertical component along with its zonal and meridional ones, is important for prediction of the Es layers formation, as well as regions of ion depletion.

Surface waves generated by Extra-Tropical Cyclones (ETCs) can significantly affect shipping, fishing, offshore oil and gas production and other marine activities. This paper presents results of satellite-data-based investigation of wind waves generated by two North Atlantic ETCs. These ETCs were fast-moving systems, inhibiting resonance (synchronism) between the group velocity of the generated waves and the ETC translation velocity. For these cases, the wave generation begins when the front-boundary of the storm appears at a given ocean location point. Since developing waves are slow, they move backward relative to the storm, grow in time, and then leave the ETC stormy area through the rear sector. Multi-satellite observations confirm such a paradigm, and reveal that the storm regions is filled up with young developing wind waves which are most developed in the rear-right sector. As observed, the energy of these waves was growing in time during the ETC life span. It is demonstrated that the extended-fetch concept (inherent for Tropical Cyclones) does not apply for ETC. Instead, by analogy, the concept of extended-duration wave growth concept is more relevant. Satellite observations well confirm the validity of duration-laws for waves generated by ETCs, and demonstrate that extended-fetch regime for observing waves can only asymptotically be achieved, - at time intervals exceeding the lifespan of considered ETCs.

In a previous companion study, satellite data were used to describe peculiar characteristics of ocean surface wave fields, generated by two extra-tropical cyclones (ETCs) rapidly propagating in the North Atlantic. Based on a 2D parametric wave model, further details are now provided to analyse and interpret the spatio-temporal evolution of ETC very intense generated waves. Significant wave height and wavelength values are shown to reach extreme values, 18 m and 500 m, respectively. Resulting energetic swell systems waves then radiate in the whole eastern part of North Atlantic, and more particularly in the Norwegian sea region. Moving to higher latitudes, wind forcing characteristics of ETCs evolve, with the shape of the wind field changing from quasi-cyclonic to "air jets/Icelandic lows". In this paper, the resulting swell generation and propagation, after the deformation of an individual ETC, are studied, as well. Confirmed with comparisons with multi-satellite observations, the application of the parametric-2D wave-ray model is demonstrated to provide robust and highly detailed information on wave generation under very complex wind regime changes.

Background: The SARS-CoV-2 laboratory PCR tests were generally reported only as binary positive or negative outcomes. Instead test positivity, these results contain a great deal of epidemiological information related to viral transmission patterns in populations. These transmission patterns during India’s SARS-CoV-2 viral waves remain largely undocumented. Methods: We analysed 2.7 million real-time polymerase chain reaction (PCR) testing records collected in Mumbai, a bellwether for other Indian cities. We used the inverse of cycle threshold (Ct) values to determine community-level viral load. We quantified wave-specific differences by age, sex and slum population density. Results: Overall PCR positivity was 3.4% during non-outbreak periods, rising to 23.2% and 42.8% during the Aleph (June-November 2020) and Omicron waves (January 2022), respectively, but only 9.9% during the Delta wave (March-June 2021). The community-level median Ct values fell and rose ~7-14 days prior to PCR positivity rates. Viral loads were 4-fold higher during the Delta and Omicron waves than during non-outbreak months. The Delta wave had high viral loads at older ages, in women and in areas of higher slum density. During the Omicron wave, differences in viral load by sex and for slum density had disappeared, but older adults continued to show higher viral load. Conclusions: Mumbai’s viral waves had markedly high viral loads representing an early signal of pandemic trajectory. Continue the vaccination in elderly Indians could reduce viral load in subsequent waves. Ct values are practicable monitoring tools.

It is shown that de Sitter accelerated expansion of the Universe (dark energy effect) is an exact solution to the set of self-consistent stochastic nonlinear gravitational waves in the FLRW metric coming to the Universe from “nowhere”.

We reviewed various physical and biological manifestations of an unprecedented large-scale water temperature anomaly that emerged in the Northeast Pacific in late 2013. The anomaly dubbed “The Blob” persisted through 2014-2016, with some signs of its persistence through 2017-2018 and a possible reemergence in 2019. The tentative timeline of The Blob’s successive appearances around the Northeast Pacific is suggestive of its advection by currents around the Gulf of Alaska, along the Aleutians, into the Bering Sea, and eventually to the Bering Strait. During the initial phase of The Blob’s development in 2013-2014, advection along the Polar Front might have played a certain role. The extreme persistence and magnitude of The Blob resulted in numerous and sometimes dramatic ecosystem responses in the eastern Bering Sea. The multi-year duration of The Blob might have preconditioned the Bering Sea for the record low seasonal sea ice extent during the winter of 2017-2018 and disappearance of the cold pool in 2016 and 2018 that profoundly affected zooplankton, invertebrates, fishes, sea birds, and marine mammals. Comparison of time-series of population responses across trophic levels suggests that The Blob lowered primary production during spring, increasing small copepod production and jellyfish, and reducing energy transfer efficiently to higher trophic levels. While the Bering Sea’s water temperature, seasonal sea ice, and cold pool seem to return to the long-term mean state in 2022, it remains to be seen if the Bering Sea ecosystem will completely recover. The two most likely alternative scenarios envision either irreversible changes or hysteresis recovery.

The initial dilution generated by the final disposal of untreated wastewater through a submarine outfall in Santa Marta was examined with a near-field dilution model. Northward and eastward seawater velocity, salinity, and temperature profiles from a 3D hydrodynamic model were used to provide the oceanic conditions to calculate the dilution. At the wastewater discharge site, the upwelling phenomenon occurs two times a year, the major from December to March and the minor in July, eliminating the stratification condition of seawater. The results of the dilution model showed that in these periods the plume reaches the water surface achieving dilutions greater than 100. In addition, the external wave effect on the initial dilution of submarine outfall discharge in Santa Marta was determined. Surface waves increase dilution during the dry period of the year when trade winds increase the surge and start the upwelling phenomenon. The Dilution with/without waves factor is up to 1.90 for the center of the plume on the water column.

The problems of formation and propagation of surface seismic waves in vertically layered and horizontally inhomogeneous media are studied. A mathematical model has been developed for the propagation of surface seismic waves in an inhomogeneous medium based on the use of the fundamental principles of wave dynamics and Fourier transforms. The existence of various types of groups of these waves is proved, and their main properties are studied. It has been established that the reflection coefficients of different groups of a dispersive wave on models of half-spaces (a layered, inhomogeneous medium) with a sharp velocity differentiation are characterized by the same dependence on the angle of incidence as in the absence of dispersion. In the region of the critical angle, which depends on the period of the incident wave, a local decrease in the intensity of wave reflection is observed, which is associated with the origin of the head dispersive wave. It has been found that the reflection coefficients of Rayleigh waves from low-velocity layers, thin (d / λ2 = 0.205) and thick (d / λ2 = 0.82) are approximately 0.2 ± 0.04 and practically do not change with increasing angle of incidence. On the basis of theoretical studies, it was revealed that reflected surface waves carry information both about the elastic properties of the reflecting medium and about the dimensions of the reflecting horizontal inhomogeneity. An experimental dispersion curve of the group velocity of Rayleigh waves on the Central Asia-Caucasus path has been obtained. The seismic stress state of the "subgrade-base" system was studied. Based on the analysis of the results of numerical experiments, it has been established that in order to obtain a complete picture of the seismically stressed state of the subgrade, it is necessary to take into account the contribution to it of each component of the accelerogram of a real earthquake.

Lamb waves occur in thin-walled structures in two wave modes, the symmetric and antisymmetric mode. Their oscillation on the structures‘ surfaces is either in phase (symmetric) or shifted by a phase angle of π (antisymmetric). In this work, a method is developed to compare the surfaces‘ oscillation phase relation. It is based on the evaluation of time signals regarding the instantaneous phase angle using the continuous wavelet transformation and as a comparative method the short-time Fourier transformation. For this purpose, numerical simulations utilizing the finite element method provide time signals from the top and bottom surface of different thin-walled structures. They differ with respect to their material settings and laminate configurations. The numerically obtained time signals are evaluated by the developed methods. The occurring oscillation phase differences on the top and bottom surface are studied and both methods are compared. Subsequently, the oscillation phase is evaluated experimentally for the wave propagation in a fiber metal laminate. It is shown that the method based on the continuous wavelet transformation is suitable for the evaluation of oscillation phase relations in time signals. Additionally, it is proven that fiber metal laminates show only two phase relations which indicates the occurrence of Lamb waves.

Conclusive evidence that specic long-term memory formation relies on den- dritic growth and structural synaptic changes has proven elusive. Connec- tionist models of memory based on this hypothesis are confronted with the so-called plasticity stability dilemma or catastrophic interference. Other fun- damental limitations of these models are the feature binding problem, the speed of learning, the capacity of the memory, the localisation in time of an event and the problem of spatio-temporal pattern generation. This paper suggests that the generalisation and long-term memory mechanisms are not correlated. Only the development and the improvement of the feature ex- tractors in the cortex involves structural synaptic changes. We suggest the long-term memory has a separate mechanism which involves protein synthe- sis to encode the information into the structure of these proteins. A model of memory should be capable of explaining the dierence between memorisation and learning. Learning has in our approach two dierent mechanisms. The generalisation in the brain is handled by the proper development of the links between neurons via synapses. The Hebbian learning rule could be applied only for this part of learning. Storing an internal ring pattern involves, in our approach, a new mechanism which puts the information regarding this ring pattern into the structure of special proteins in such a way that it can be retrieved later. The hypotheses introduced in this article includes a physiological assumption which has not been yet verified because it is not currently experimentally accessible. Keywords: Waves, Protein Synthesis, Resonance, Long Term Memory Preprint submitted to Neural Networks

A Shape Memory Alloy (SMA) enabled Overtopping Wave Energy Converter (OWEC) that maximizes its overtopping discharge, and thus energy output under different wave conditions is presented. Among all the parameters affecting the overtopping discharge rate, the crest freeboard height is the most influential one to control the overtopping discharge rate and the stored overtopping volume behind it. Currently, all the OWEC crest freeboard heights are fixed by design to maximize the discharge rate on one particular sea state. In the present study, we show that the SMA can adjust the crest freeboard height through a control system based on the sea state and achieve an optimal overtopping discharge rate. A scaled OWEC model is built in the lab with its crest freeboard height controlled by springs made of SMA. The length (and thus tension) of the springs is controlled by temperature changes by changing the passing current through the springs. By adjusting the length of the springs based on the incoming wave condition, we adjust the freeboard to an optimal height known to generate a maximum overtopping discharge rate for energy conversion. This smart material-enabled design can maximize the overtopping discharge and thus the output power of the OWEC under various wave conditions. Furthermore, the simplicity of using SMA springs as the actuator leads to the minimum number of moving mechanical parts, which can remarkably decrease maintenance costs. As the proof of concept, two types of tests are conducted in the laboratory using the same OWEC model under several random wave trains generated from spectra with different significant wave heights - one type with a fixed crest freeboard height and the other type featuring the adjustable crest freeboard height controlled by the springs. The substantial increase of harvested output power in the OWEC with the adjustable crest freeboard height may pave the way for more efficient wave energy conversion systems.

This work investigates how integrated polyimide inlays with applied sensor bodies influence the guided ultrasonic wave propagation in narrow glass fiber-reinforced polymer specimens. Preliminary numerical simulations indicate that in a damping-free specimen, the inlays show reflections for the S0-mode propagation. Hence, an air-coupled ultrasonic technique and a 3D laser Doppler vibrometer measurement are used to measure different parts of the propagating waves’ displacement field after burst excitation at different frequencies. No significant reflections on the inlay can be seen in the experiments. However, it is shown that the reflections from the strip specimen’s narrow width cause periodical reflections that superimpose with the excited wave fronts. A continuous wavelet transformation in the time-frequency domain filters discontinuities from the measurement signal and is used for reconstruction of the time signals. The reconstructed signals are used in a spatial continuous wavelet transformation to identify the occurring wavelengths and hence to prove the assumption of reflections from the narrow edges. Since the amplitude of the reflections identified in the numerical data at the polyimide inlays are an order of magnitude smaller than the excited wave packages, it is concluded that material damping of the epoxy resin matrix extincts possible reflections from the inlays.

Shock waves, as used in medicine, can induce cell permeabilization, genetically transforming filamentous fungi; however, little is known on the interaction of shock waves with the cell wall. Because of this, the selection of parameters has been empirical. We studied the influence of shock waves on the germination of Aspergillus niger, to understand their effect on the modulation of four genes related to the growth of conidia. Parameters were varied in the range reported in protocols for genetic transformation. Vials containing conidia in suspension were exposed to either 50, 100 or 200 single-pulse or tandem shock waves, with different peak pressures (approximately 42, 66 and 83 MPa). In the tandem mode, three delays were tested. To equalize the total energy, the number of tandem “events” was halved compared to the number of single-pulse shock waves. Our results demonstrate that shock waves do not generate severe cellular effects on the viability and germination of A. niger conidia. Nevertheless, increase in the aggressiveness of the treatment induced a modification in the four genes tested. Scanning electron microscopy revealed significant changes to the cell wall of the conidia. Under optimized conditions, shock waves could be used for several biotechnological applications, surpassing conventional techniques.

An overview is presented of several diverse branches of work in the area of effectively 2D fluid equilibria which have in common that they are constrained by an infinite number of conservation laws. Broad concepts, and the enormous variety of physical phenomena that can be explored, are highlighted. These span, roughly in order of increasing complexity, Euler flow, nonlinear Rossby waves, 3D axisymmetric flow, shallow water dynamics, and 2D magnetohydrodynamics. The classical field theories describing these systems bear some resemblance to perhaps more familiar fluctuating membrane and continuous spin models, but the fluid physics drives these models into unconventional regimes exhibiting large scale jet and eddy structures. From a dynamical point of view these structures are the end result of various conserved variable forward and inverse cascades. The resulting balance between large scale structure and small scale fluctuations is controlled by the competition between energy and entropy in the system free energy, in turn highly tunable through setting the values of the conserved integrals. Although the statistical mechanical description of such systems is fully self-consistent, with remarkable mathematical structure and diversity of solutions, great care must be taken because the underlying assumptions, especially ergodicity, can be violated or at minimum lead to exceedingly long equilibration times. Generalization of the theory to include weak driving and dissipation (e.g., non-equilibrium statistical mechanics and associated linear response formalism) could provide additional insights, but has yet to be properly explored.

Analyzing the records of Advanced LIGO and Virgo gravitational observatories, we found a specific time-domain asymmetry inherent only to the signals of their gravitational detectors. Experiments with different periodic signals, Gaussian and non-Gaussian noises, made it possible to conclude that the noise of gravitational detectors is an unusual mixture of signals. We also developed a specialized Pearson correlation analyzer to recognize the gravitational-wave events. It turned out that the LIGO detectors’ output signals include a significant (– 6 dB) component, which has the properties of records of reliably recognized gravitational waves. It allows us to argue that the gravitational background noise is largely due to the processes of merging astronomical objects. Since the specific signal is registered by the detectors continuously, we can consider the sub-kilohertz band gravitational oscillations field as detected. Our analysis method also allows us to estimate the contribution of the gravitational background component to the total signal energy. With its help, it will be possible not only to provide the radio-frequency estimation of the magnitude of gravitational disturbances but also, possibly, to construct a map of the gravitational noise of the sky.

Structural health monitoring of lightweight constructions made of composite materials can be performed using guided ultrasonic waves. If modern fiber metal laminates are used, this requires integrated sensors that can record the inner displacement oscillations caused by the propagating guided ultrasonic waves. Therefore, we have developed a robust MEMS vibrometer that can be integrated with structural and functional compliance. This vibrometer is directly sensitive to the high-frequency displacements from structure-borne ultrasound when excited between its first and second natural frequency. The vibrometer is mostly realized by processes earlier developed for a pressure sensor but with additional femtosecond laser ablation and wafer bonding. The piezoresistive transducer made from silicon is encapsulated between top and bottom glass lids. The natural frequencies are experimentally determined using an optical micro vibrometer setup. The vibrometer functionality and usability for structural health monitoring are demonstrated on a customized test rig by recording application-relevant guided ultrasonic wave packages with a central frequency of 100 kHz at a distance of 200 mm from the exciting ultrasound transducer.

Guided ultrasonic waves are suitable for use in the context of structural health monitoring of thin-walled, plate-like structures. Hence, observing the wave propagation in the plates can provide an indication of whether damage has occurred in the structure. In this work, the wave propagation in fiber metal laminate consisting of thin steel foils and layers of carbon fiber-reinforced polymer is studied, focusing on the main propagation characteristics like dispersion diagrams and displacement fields. For this purpose, the dispersion diagrams derived from the analytical framework and numerical simulations are first determined and compared to each other. Next, the displacement fields are computed using the global matrix method for two excitation frequencies. The results derived from the analytical framework is used to validate numerically determined displacement fields based on a 2D and a 3D modeling approach. For both investigations the results of the analytical treatment and the numerical simulation show good agreement. Furthermore, the displacement field reveals the typical and well-known characteristics of the propagation of guided waves in thin-walled structures. Since the use of full 3D models involves a very high computational cost, this work also successfully investigates the possibility for model order reduction to decrease the computational time and costs of the simulation without the loss of accuracy.

Numerical methods, including machine learning methods, are now actively used in the applications related to guided wave propagation. The method proposed in this study for material properties characterization is based on the algorithm of the clustering of multivariate data series obtained as a result of the application of the matrix pencil method to the experimental data. In the proposed technique, multi-objective optimization is employed to improve the accuracy of particular parameter identification. At the first stage, the computationally efficient method based on the calculation of the Fourier transform of Green's matrix is employed iteratively and the obtained solution is used for the filter construction with decreasing bandwidth, which allows us to obtain nearly noise-free classified data (with mode separation). The filter provides data separation between all guided waves in a natural way, which is needed at the second stage, where the slower method based on the minimization of the slowness residuals is applied to the data. The method might be applied for material properties identification in plates with thin coatings/interlayers, multi-layered anisotropic laminates etc.

Frequency combs (FCs)—spectra containing equidistant coherent peaks—have enabled researchers and engineers to measure the frequencies of complex signals with high precision thereby revolutionising the areas of sensing, metrology and communications and also benefiting the fundamental science. Although mostly optical FCs have found widespread applications thus far, in general FCs can be generated using waves other than light. Here, we review and summarise recent achievements in the emergent field of acoustic frequency combs (AFCs) including phononic FCs and relevant acousto-optical, Brillouin light scattering and Faraday wave-based techniques that have enabled the development of phonon lasers, quantum computers and advanced vibration sensors. In particular, our discussion is centred around potential applications of AFCs in precision measurements in various physical, chemical and biological systems in conditions, where using light, and hence optical FCs, faces technical and fundamental limitations, which is, for example, the case in underwater distance measurements and biomedical imaging applications. This review article will also be of interest to readers seeking a discussion of specific theoretical aspects of different classes of AFCs. To that end, we support the mainstream discussion by the results of our original analysis and numerical simulations that can be used to design the spectra of AFCs generated using oscillations of gas bubbles in liquids, vibrations of liquid drops and plasmonic enhancement of Brillouin light scattering in metal nanostructures. We also discuss the application of non-toxic room-temperature liquid-metal alloys in the field of AFC generation.

Ultrasonic based inspection of thin-walled structures often requires prior knowledge of their mechanical properties. Their accurate estimation could be achieved in a non-destructive manner employing, e.g., elastic guided waves. Such procedures require efficient approaches for experimental data extraction and processing, which is still a challenging task. An advanced automated technique for material properties identification of an elastic waveguide is proposed in this investigation. It relies on the information on dispersion characteristics of guided waves, which are extracted by applying the matrix pencil method to the measurements obtained via laser Doppler vibrometry. Two objective functions have been successfully tested, and the advantages of both approaches are discussed (accuracy vs computational costs). The numerical analysis employing the synthetic data generated via the mathematical model as well as experimental data shows that both approaches are stable and accurate. The influence of the presence of various modes in the extracted data is investigated. One can conclude that the influence of the corruptions related to the extraction of dispersion curves is not critical if the majority of guided waves propagating in the considered frequency range are presented. Possible extensions of the proposed technique for damaged and multi-layered structures are also discussed.

Recently, a rising use of wireless internet technologies has been demonstrated. The devices 18 which use these technologies emit in new spectral regions an electromagnetic radiation (EMFs) 19 which could interact with the male reproductive system. The aim of this study was to investigate in 20 vitro influence of electromagnetic fields at 27 GHz on sperm quality in Mytilus galloprovincialis. 21 Sperm samples, were collected from sexually mature males of M. galloprovincialis and placed in sea- 22 water. Once evaluated the number and quality of spermatozoa, sperm cells were exposed to elec- 23 tromagnetic fields radiated by a pyramidal horn antenna. The effect of exposure was evaluated after 24 10, 20, 30, 40 and 60 minutes with light microscope and using Eosin test. Ten replications were per- 25 formed for each time series, and statistical analysis was carried out byt-test. A significative decrease 26 in sperm motility was observed after 10 minutes of exposure and after 30 minutes most of sperms 27 were immobile and not vital. This study provides useful data on potential ecological impact of the 28 5G high-band on animal fertility, whose effect is currently under investigation.

The article discusses the possibility of detecting of gravitons using recently created devices with cold atoms at picokelvin temperatures.

Laminate structures composed of stiff plates and thin soft interlayers are widely used in aerospace, automotive and civil engineering encouraging the development of reliable non-destructive strategies for their condition assessment. In the paper, elastodynamic behaviour of such laminate structures is investigated with emphasis on its application in ultrasonic based NDT and SHM for the identification of interlayer mechanical and interfacial contact properties. A particular attention is given to the practically important frequency range, in which the wavelength considerably exceeds the thickness of the film. Three layer model with spring-type boundary conditions employed for imperfect contact simulation is used for numerical investigation. Novel effective boundary conditions are derived via asymptotic expansion technique and used for analysis of the peculiar properties of elastic guided waves in considered laminates. It is revealed that the thin and soft film influences the behaviour of the laminate mainly via the effective stiffnesses being a combination of the elastic moduli of the film, its thickness and interface stiffnesses. To evaluate each of these parameters separately (or to figure out that the available experimental data are insufficient), a step-wise procedure employing the effective boundary conditions is proposed and tested versus the laser Doppler vibrometry data for Lamb waves in Aluminium/Polymer film/Alumunium structure. The possibility of using film-related thickness resonance frequencies to estimate the film properties and contact quality is also demonstrated. Additionally, the rich family of edge waves is also investigated, and the splitting of fundamental edge waves into pairs is revealed.

5G technology is evolving to satisfy several service requirements favoring high data-rate connections and lower latency times than current ones (< 1ms). 5G systems use different frequency bands of the radio wave spectrum, taking advantage of higher frequencies than previous mobile radio generations. In order to guarantee a capillary coverage of the territory for high reliability applications, it will be necessary to install a large number of repeaters because higher frequencies waves have a lower capacity to propagate in free space. Following the introduction of this new technology, there has been a growing concern about possible harmful effects on human health. The aim of this study is investigating possible short term effects induced by 5G-millimeter waves on embryonic development of Danio rerio. We have exposed fertilized eggs to 27 GHz frequency, 9.7 mW/cm2 incident power density, 23 dbm and have measured several endpoints every 24 hours. The exposure to electromagnetic fields at 27 GHz (5G) caused no significant impacts on mortality nor on morphology because the exposed larvae showed a normal detachment of the tail, presence of heart-beat and well-organised somites. A weak positivity on exposed larvae has been highlighted by immunohistochemical analysis.

The energy potential of long-period oscillations is estimated by comparing it with watercourse power. The relaxation time of long-period waves is chosen for the estimation time interval, during which their amplitude decreases e (Euler's number) times from the initial one. According to calculations, the amount of energy produced during this time by the watercourse is 9.35–18.71 million kW×h, while the amount of energy of long-period oscillations is 3–6 times less – 1.60–5.48 million kW×h. The components of the economic factor of using long-period waves and currents for electricity production are the predictability of their magnitudes and location of maxima, long-term availability, concentration.

In this paper, we introduce a new formulation based on Floquet (Fourier) spectral analysis combined with a spectral modulation technique (and its spatial form) to study strongly coupled sublattices predefined in the infinite and large finite extent of almost periodic antenna arrays (e.g metasurfaces). This analysis is very relevant for dense massive MIMO, intelligent surfaces, 5G, and 6G applications (used for very small areas with a large number of elements such as millimeter and terahertz waves applications). The numerical method that is adopted to model the structure is the method of moments simplified by equivalent circuits MoM GEC. Other numerical methods (as the ASM array scanning method and windowing Fourier method) used this analysis in their kernel that to treat periodic and pseudo-periodic (or quasi-periodic) arrays.

Physical processes play important roles in controlling eutrophication and oligotrophication. In stratified lakes, internal waves can cause vertical transport of heat and nutrients without breaking the stratification, through boundary mixing events. Such is the case in tropical Valle de Bravo (VB) lake, where strong diurnal winds drive internal waves, boundary mixing and hypolimnetic warming during stratification periods. We monitored VB during 18 years (2001-2018) when important water-level fluctuations (WLF) occurred, affecting mixing and nutrient flux. Mean hypolimnetic temperature increase (0.06–1.04°C month-1) occurred in all the stratifications monitored. We analyzed temperature distributions and modeled the hypolimnion heat budget to assess vertical mixing between layers (26,618–140,526 m-3h-1), vertical diffusivity coefficient KZ (6.2x10-7–3.3x10-6 m2s-1) and vertical nutrient entrainment to epilimnion on monthly scale. Stability also varied as a function of WLF. Nutrient flux to the epilimnion ranged 0.36–5.99 mg m-2d-1 for soluble reactive phosphorus (SRP) and 5.8–97.1 mg m-2d-1 for dissolved inorganic nitrogen (DIN). During low water-level years, vertical nutrient fluxes increase and can account for up to &gt;40% of the total external nutrients load to the lake. Vertical mixing changes related to WLF affect nutrient recycling, their flux to sediments, ecosystemic metabolic balance and planktonic composition of VB.

Given the documented wave-induced damage of elevated coastal decks during extreme natural hazards (e.g. hurricanes) in the last two decades, it is of utmost significance to decipher the wave-structure-interaction of complex deck geometries and quantify the associated loads. Therefore, this study focuses on the assessment of solitary wave impact on open-girder decks that allow the air to escape from the sides. To this end, an arbitrary Lagrangian-Eulerian (ALE) numerical method with a multi-phase compressible formulation is used for the development of three-dimensional hydrodynamic models, which are validated against a large-scale experimental dataset of a coastal deck. Using the validated model as a baseline, a parametric investigation of different deck geometries with a varying number of girders Ng and three different widths, was conducted. The results reveal that the Ng of a superstructure has a complex role and that for small wave heights the horizontal and uplift forces increase with the Ng, while for large waves the opposite happens. If the Ng is small the wave particles accelerate after the initial impact on the offshore girder leading to a more violent slamming on the onshore part of the deck and larger pressures and forces, however, if Ng is large then unsynchronized eddies are formed in each chamber, which dissipate energy and apply out-of-phase pressures that result in multiple but weaker impacts on the deck. The decomposition of the total loads into slamming and quasi-static components, reveals surprisingly consistent trends for all the simulated waves, which facilitates the development of predictive load equations. These new equations, which are a function of Ng and are limited by the ratio of the wavelength to the deck width, provide more accurate predictions than existing empirical methods, and are expected to be useful to both engineers and researchers working towards the development of resilient coastal infrastructure.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

This article discusses the potential advantages of a data processing technique for continuous gravitational wave signals searches in the data measured by ground-based gravitational wave interferometers. Its main advantage over other techniques is that it does not need to search over the signal’s direction of propagation. Although it is a “ coherent method” (i.e. it coherently processes year-long data), it is applied to a data set obtained by multiplying the original time-series with a (half-year) time-shifted copy of it. As a result, the phase modulation due to the interferometer motion around the Sun is automatically canceled in the signal of the synthesized time-series. Although the resulting signal-to-noise ratio is not as high as that of a coherent search, it equals that of current hierarchical methods. In addition, since the signal search is performed over a parameters space of smaller dimensionality, the associated false-alarm probability should be smaller than those characterizing hierarchical methods and result in an improved likelihood of detection.

We present a numerical calculation of the heat transport in a Bragg mirror configuration made of materials that do not obey Fourier's law of heat conduction. The Bragg mirror is made of materials that are described by the Cattaneo-Vernotte equation. By analyzing the Cattaneo-Vernotte equation's solutions, we define the thermal wave surface impedance to design highly reflective thermal Bragg mirrors. Even for mirrors with a few layers, very high reflectance is achieved ($>90\%$). The Bragg mirror configuration is also a system that makes evident the wave-like nature of the solution of the Cattaneo-Vernotte equation by showing frequency pass-bands that are absent if the materials obey the usual Fourier's law.

The use of convolutional neural networks (CNNs) in image classification has become the standard method of approaching computer vision problems. Here we apply pre-trained networks to classify images of non-breaking, plunging and spilling breaking waves. The CNNs are used as basic feature extractors and a classifier is then trained on top of these networks. The dynamic nature of breaking waves is exploited by using image sequences to gain extra information and improve the classification results. We also see improved classification performance in using pre-computed image features such as the optical flow between image pairs. The inclusion of the dynamic information improves the classification between breaking wave classes. We also provide corrections to the methodology from the article from which the data originates to achieve a more accurate assessment of performance.

Background: Heat waves are correlated with increased mortality in the aged population. Social isolation is known as a vulnerability factor. This study aims at evaluating the correlation between an intervention to reduce social isolation and the increase in mortality in the population over 80 during heat waves. Methods: The study adopts a retrospective ecologic design. We compared the excess mortality rate (EMR) in the over 80 population during heat waves in urban areas of Rome (Italy), where a program to reduce social isolation was implemented compared to others where it was not implemented. We measured mortality of the summer periods from 2015 to 2019 compared with 2014 (a year without heat waves). Winter mortality, cadastral income and proportion of over 90 were included in the multivariate Poisson regression. Results: The EMR in the intervention and controls was 2.70% and 3.81%, respectively. Rate ratio 0.70 (c.i. 0.54 - 0.92, p-value 0.01). The Incidence Rate Ratio (IRR) of the interventions with respect to the controls is 0.76 (c.i. 0.59 - 0.98). After adjusting for other variables, the IRR was 0.44 (c.i. 0.32 - 0.60). Conclusions: Reducing social isolation could limit the impact of heat waves on the mortality of the elderly population.

The spectra of the plasma emitted from the studied samples consist of several dozens of narrow bands superimposed on each other. Tables of spectral lines were used to interpret the spectra. It turned out that the largest number of bands corresponds to the radiation of positively charged ions and atoms of elements that make up the crystal lattices of minerals that make up the studied rocks. Thus, the spectra of the plasma emitted from quartz corresponded to the radiation of atoms and positively charged silicon ions, the charge of which varied from 1 to 4, as well as atoms and positively charged oxygen ions, the charge of which varied from 1 to 3. Positively charged ions and atoms of Si, O, K, Ca, Al and Na, which are part of the crystal lattices of quartz and feldspar, flew out of granites. Positively charged ions and Ca, C and O atoms flew out of the calcite.

In this article, we show theoretically and experimentally the formation of spin-waves band gaps in a magnonic crystal that was implemented by the deposition of periodic micro-structured strips of magnetite nanoparticles. A theoretical model describing the spectra of the transmitted spin-waves bandgaps is proposed. This is achieved using a simple model based on microwave transmission line theory and considering the presence of micro-structured strips of magnetite nanoparticles on the surface. Such magnonic crystal of equally spaced micro-structured strips of magnetite nanoparticles on the surface of an yttrium iron garnet thin film has been implemented and measured. The periodic micro-structured nanoparticles are deposited on the surface of such yttrium iron garnet single-crystal film grown on a gallium-gadolinium garnet substrate via dip-coating technique. Propagation of magnetostatic surface spin-waves is studied and it is shown that the presence of such periodic structure leads to the formation of spin-wave band gaps in the transmission characteristics. The spin-wave detection has been carried out using a pair of microwave antennas and a vector network analyzer. The results show that the periodic structure formed by the magnetite strips modifies the spectra of the transmitted spin waves producing band gaps.

Developing new technologies is essential for advancement in solar cell technologies due to their ability to only absorb light mainly in the visible light spectrum. Super crystals Nd³⁺- Eu³⁺ optical characteristics display higher absorption of light waves than single crystals of Eu³⁺ and Nd³⁺ due to a two-photon absorption energy transfer mechanism known as upconversion. Super crystals Nd³⁺- Eu³⁺ display higher absorption due to fewer light waves being transmitted through materials as reported in spectra data. Transmission spectra data reflects that Nd³⁺- Eu³⁺ nanoparticles are great candidates to enhance light absorption in solar cell devices.

The amplified Arctic warming is one of several factors influencing atmospheric dynamics. In this work, we consider a series of numerical experiments to identify the direct role of the Arctic sea ice reduction process in forming climatic trends in the northern hemisphere. Aimed at this, we used two more or less independent mechanisms of ice reduction. The first is traditionally associated with increasing the concentration of carbon dioxide in the atmosphere from the historic level of 360 ppm to 450 ppm and 600 ppm. This growth increases air temperature and decreases the ice volume. The second mechanism is associated with a reduction in the reflectivity of ice and snow. We assume that comparing the results of these two experiments allows us to judge the direct role of ice reduction. The most prominent consequences of ice reduction, as a result, were the weakening of temperature gradient at the tropopause level in mid-latitudes, the slower zonal wind at 50-60∘N, intensification of wave activity in Europe, Western America, and Chukotka, and its weakening in the south of Siberia and Kazakhstan. We also consider how climate change may alter regimes such as blocking and stationary Rossby waves. The study used the INM-CM48 climate system model .

The instability of traveling pulses in nonlinear diffusion problems is inspected on the example of Gunn domains in semiconductors. Mathematically the problem is reduced to the calculation of the "energy" of the ground state in Schrödinger equation with a complicated potential. A general method to obtain the bottom-part spectrum of such equations based on the approximation of the potential by square wells is proposed and applied. Possible generalization of the approach to other types of nonlinear diffusion equations is discussed.

Ultrasonic measurements are used in civil engineering for structural health monitoring of concrete infrastructures. The late portion of the ultrasonic wavefield, the coda, is sensitive to small changes in the elastic moduli of the material. Coda Wave Interferometry (CWI) correlates these small changes in the coda with the wavefield recorded in intact, or unperturbed, concrete specimen to reveal the amount of velocity change that occurred. CWI has the potential to detect localised damages and global velocity reductions alike. In this study, the sensitivity of CWI to different types of concrete mesostructures and their damage levels is investigated numerically. Realistic numerical concrete models of concrete specimen are generated and damage evolution is simulated using the discrete element method. In the virtual concrete lab, the simulated ultrasonic wavefield is propagated from one transducer using a realistic source signal and recorded at a second transducer. Different damage scenarios reveal a different slope in the decorrelation of waveforms with the observed reduction in velocities in the material. Finally, the impact and possible generalizations of the findings are discussed and recommendations are given for a potential application of CWI in concrete at structural scale.

Propagation of electromagnetic (EM) waves inside and on the surface of the human body is the subject of active research in area of biomedical applications. This research area is the basis for wireless monitoring of biological object parameters and characteristics. Much attention has been paid to radio-frequency identification systems, which are intended for biomedical applications. Solutions to the following problems are crucial to achieve the stated goals in the area of wireless monitoring: EM wave propagation inside regular and multilayer biological media, through the interface between different media, and on-body surface wave propagation. The biological object monitoring is based on a consideration of the followingprocesses: a) propagation of the EM wave in a biological medium considered as the dielectric with a high dielectric permittivity and substantial conductivity; b) penetration of the EM wave through the biological medium–air interface (wave reflection and refraction); c) propagation of the EM wave in a multi-layer biological medium; d) propagation of the EM wave along the plane or curved surface of biological objects.

The work presents a Structural Health Monitoring (SHM) electronic system with real-time ac-quisition and processing for the determination of impact location in laminates. The novelty of this work is the quantitative evaluation of impact location errors using the Lamb wave guided mode S0, captured and processed in real-time by up to eight piezoelectric sensors. The differential time of arrival is used to minimize an error function for the position estimation. The impact energy is correlated to the amplitudes of the antisymmetric (A0 ) mode and the electronic design is de-scribed to avoid saturation for signal acquisition. The same electronic is designed to acquire symmetric (S0 ) low level signals by adequate gain, bandwidth and signal to noise ration. Such signals propagate into a 1.4mm thick aluminum laminate at the group velocity of 5150m/s with frequency frequency components above 270kHz and can be discriminated from the A0 mode to calculate accurately the differential arrival time. The results show that the error is not improved better than S0 wavelength in impact localization by using six out of eight sensors connected to the electronic system.

ABSTRACT. In this paper, we suggest a biomathematical numerical method for analysing mRNA nucleotides sequences based on UA/CG Fibonacci numbers proportions. This method is used to evaluate then compare the spike genes related to the main SARS-CoV2 VARIANTS currently circulating within the world population. The 10 main results proposed to be reproduced by peers are: 1/ SARS-CoV2 genome and spike evolution in one year 2020-2021. 2/ SARS-CoV2 Origins. 3/ Comparing 11 reference variants spikes. 4/ analysing 32 CAL.20C California variant patients spikes. 5/ Toward a meta mRNA Fibonacci gene end message code. 6/ Analysing S501 UK, S484 South Africa and « 2 mutations » INDIA variants. 7/ Suggesting a possible variants spike mRNA palindrome symmetry metastructure improving mRNA stability then infectiousness. 8/ Analysing Fibonacci Metastructures in the mRNA coding for the vaccines PFIZER and MODERNA. 9/ Does the CG-rich modification of the synonymous codons of the spikes of the 2 mRNA vaccines affect the expression and quantity of SARS-CoV2 antibodies? 10/ The exceptional case of the Brazilian variant P.1. Particularly, we suggest the following conjecture at mRNA folding level : CONJECTURE of SARS-CoV2 VARIANTS: The growth of long Fibonacci structures in the shape of "podiums" for almost all of the variants studied (UK, California, South Africa, India, etc.) suggests the probable folding of the Spike mRNA in the form of a "hairpin", which can strengthen the cohesion and the lifespan of this mRNA. Finally, we show that these kinds of Fibonacci matastructures disapear TOTALLY by analysing the published mRNA sequences of PFIZER and MODERNA vaccines. One fact is certain, the two mRNAs of the Moderna and Pfizer vaccines will result in a low functionality of the spike vaccine. This is because their designers by seeking greater stability, have doped to build CG rich sequences which, as soon as they are inserted into the human host, will, paradoxically, seek to mutate, like SARS-CoV2 variants, towards CG ==> UA forms in order to improve their STABILITY and LIFETIME. We conclude using new biomathematics theoretical methods (Master code and numerical standing waves), and comparing the Spikes of the two vaccines Moderna and Pfizer, that there will be very probable differences in stability and shelf life of the two respective mRNAs vaccines. However, “State of the Art” analyzes will disclose that their two protein sequences are strictly identical. By modified their synonymous codons using different strategies, no one can guarantee that the quantity of antibodies generated will be identical in the two cases. We wish to draw attention to the great ADAPTATION power - at the global scale of their genomes - of the most infectious VARIANTS, such as the BRAZIL 20J / 501Y.V3 variant (P.1). This is very worrying for the VACCINES <==> VARIANTS run: We demonstrate how the Brazilian variant P.1 which becomes uncontrollable in Brazil in April 2021 has a level of organization of long metastructures of 17,711 bases covering the genome which is 3.6 more important than that of the 2 reference genomes SARS-CoV2 and worldwide D614G. We suggest that this high level of overall structure of this variant contributes to the stability of this genome and, might explain its greater contagiousness.

Nonionizing millimeter-waves (MMW) interact with cells in a variety of ways. Here the inhibited cell division effect was investigated using 85-105 GHz MMW irradiation within the ICNIRP (International Commission on Non-Ionizing Radiation Protection) non-thermal 20 mW/cm2 safety standards. Irradiation using a power density of about 1.0 mW/cm2 , SAR over 5-6 hours on 50 cells/μl samples of Saccharomyces cerevisiae model organism resulted in 62% growth rate reduction compared to the control (sham). The effect was specific for 85-105 GHz range, and was energy and cell density dependent. Irradiation of wild type and Δrad52 (DNA damage repair gene) deleted cells presented no differences of colony growth profiles indicating non-thermal MMW treatment does not cause permanent genetic alterations. Dose versus response relations studied using a standard horn antenna (~1.0 mW/cm2) and compared to that of a compact waveguide (17.17 mW/cm2) for increased power delivery resulted in complete termination of cell division via non-thermal processes supported by temperature rise measurements. We have shown that non-thermal MMW radiation has potential for future use in treatment of yeast related diseases and other targeted biomedical outcomes.

This review article is focused on the analysis of the state of the art of sensors for guided 9 ultrasonic waves for the detection and localization of impacts, therefore of interest for the structural 10 health monitoring (SHM). The recent developments in sensor technologies are then reported and 11 discussed through the many references in recent scientific literature. The physical phenomena re-12 lated to impact event and the main physical quantities are then introduced to discuss their im-13 portance in the development of the hardware and software components for SHM systems. An im-14 portant aspect of the article is the description of the different ultrasonic sensor technologies cur-15 rently present in the literature and what advantages and disadvantages they could bring, in relation 16 to the various phenomena investigated. In this context, the analysis of the front-end electronics is 17 deepened, the type of data transmission both in terms of wired and wireless technology and in terms 18 of online and offline signal processing. The integration aspects of sensors for the creation of net-19 works with autonomous nodes with the possibility of powering through energy harvesting devices 20 and the embedded processing capacity is also studied. Finally, the emerging sector of processing 21 techniques using deep learning and artificial intelligence concludes the review by indicating the 22 potential for the detection and autonomous characterization of the impacts.

An abdominal aortic aneurysm (AAA) is usually asymptomatic until rupture, which is associated with extremely high mortality. Consequently, early detection of AAAs is of paramount importance in reducing mortality; however, most AAAs are detected by medical imaging incidentally. The aim of this study was to investigate the feasibility of machine learning-based pulse wave (PW) analysis for the early detection of AAAs using a database of in silico PWs. PWs in the large systemic arteries were simulated using one-dimensional blood flow modelling. A database of in silico PWs representative of subjects (aged 55, 65 and 75 years) with different AAA sizes was created by varying the AAA-related parameters with major impacts on PWs – identified by parameter sensitivity analysis – in an existing database of in silico PWs representative of subjects without AAA. Then, a machine learning architecture for early detection of AAAs was proposed, which was trained and tested using the new in silico PW database. The parameter sensitivity analysis revealed that the AAA maximum diameter and stiffness of the large systemic arteries were the dominant AAA-related biophysical properties that significantly influence the PW. The simulated PW indexes extracted from the database showed that the PW was not only influenced by the presence of an AAA but was also significantly affected by multiple cardiovascular parameters that compromised the detection of AAAs by using individual PW indexes. Alternatively, the trained machine learning model performed well in classifying normal and AAA conditions using digital photoplethysmogram PWs from the database. These findings suggest that machine learning-based PW analysis is a promising approach for AAA screening using PW signals acquired by wearable devices.

Wave breaking is one of the most important yet poorly understood water wave phenomena. It is via wave breaking that waves dissipate most of their energy and the occurrence of wave breaking directly influences several environmental processes, from ocean-atmosphere gas exchanges to beach morphodynamics. Large breaking waves also represent a major threat for navigation and for the survivability of offshore structures. This paper provides a systematic search for intermediate to deep water breaking waves with particular focus on the elusive occurrence of plunging breakers. Using modern remote sensing and deep learning techniques, we identify and track the evolution of over four thousand unique wave breaking events using video data collected from La Jument lighthouse during ten North Atlantic winter storms. Out of all identified breaking waves (Nb=4683), ≈22% were dominant breaking waves, that is, waves that have speeds within [0.77cp, 1.43cp], where cp is the peak wave speed. Correlations between the occurrence rate of dominant breaking waves (that is, waves per area and time per peak wave period) and wave steepness and wave age were observed. As expected, the number of identified plunging waves was small and six waves of all detected breaking waves, or 0.13%, could undoubtedly be considered as plunging waves. Two waves were also identified as unusually large, or rogue waves. Although afflicted by several technical issues, the data presented here provides a good indication that the probability of occurrence of plunging waves should be better incorporated into the design of offshore structures, particularly the ones that aim to harvest energy in offshore environments.

The purpose of this paper is to study the sliding mode control as a Ricci flow process in the context of a three-story building structure subjected to seismic waves. The stability conditions result from two Lyapunov- functions, the first associated with slipping in a finite period of time, and the second with convergence of trajectories to the desired state. Simulation results show that the Ricci flow control leads to the minimization of the displacements of the floors. 3D Ricci solitons projection via a semi-conformal mapping to a surface is also studied.

The cartographic cum site-effectuated view of Shillong region of northeast India is presented here. Starting from the existing tectonics, the prevalent geological settings of the study area is comprehensively delineated. The seismic prone area is further overviewed in the context of site effects with accompaniment of available borehole information. The resonance frequency estimates form ambient noise survey along with receiver functions are outlined which implicates a heterogeneous subsurface. This further helps in segregating the region into two compelling profiles, thereby enabling us to get a deeper insight in the probable subsurface as well as heterogeneity. Eventually, the influence of topography over strata was also highlighted and interpreted as well.