This paper attempts at applying adaptive network-based fuzzy inference system (ANFIS) for analysis of the resonant frequency of a microstrip rectangular patch antenna with two equal size slots which are placed on the patch vertically. The resonant frequency is calculated as the position of slots is shifted to the right and left sides on the patch. As a result , the antenna resonates at more than one frequency . Commonly, machine algorithms based on artificial neural networks are employed to recognize the whole resonant frequencies. However ,they fail to estimate the resonant frequencies correctly as in some cases variations are not very sensible and the resonant frequencies overlap each other . It can be concluded that artificial neural networks could be replaced in such designs by the adaptive network-based fuzzy Inference system due to its high approximation capability and much faster convergence rate.

Electric vehicles (EV) are getting more commonplace in the transportation sector in recent times. As the present trend suggests, this mode of transport is likely to replace the internal combustion engine (ICE) vehicles in near future. Each of the main EV components has a number of technologies that are currently in use or can become prominent in the future. EVs can cause significant impacts on the environment, power system, and other related sectors. The present power system can face huge instabilities with enough EV penetration; but with proper management and coordination, EVs can be turned into a major contributor to the successful implementation of smart grid. There are possibilities of immense environmental benefits as well, as the EVs can extensively reduce the greenhouse gas emission from the transportation sector. However, there are some major obstacles for EVs to overcome before replacing the ICE vehicles totally. This paper is focused on reviewing all the useful data available on EV configurations, energy sources, motors, charging techniques, optimization techniques, impacts, trends, and possible directions of future developments. Its objective is to provide an overall picture of the current EV technology and ways of future development to assist in future researches in this sector.

Mobile devices have become tools we spend our free time where we carry them with us every moment, they allow us to interact with the environment, we immortalize the moment when necessary. These devices which we spend most of our daily life become very common in recent years and even there are unique business areas emerged. It was announced that the number of people using smartphones is over than 2.5 billion in the first quarter of 2016. As people become more addicted to mobile technology, they become the target of malevolent people. A huge increase in the number of mobile malware is observed as the number of the users increase. Billions of users at risk day by day due to the development of the methods. We have addressed the recent methods used and the types of malware that target mobile devices in our study. We have mentioned the proxy server and reverse proxy server operation logic. We discuss the method of turning mobile devices into reverse proxy servers, risks involved and protection methods.

Analysis of 1382 measures of battery State of Health (SoH) from 283 Nissan Leafs (“Leaf/s”), manufactured between 2011 and 2017, has detected a faster rate of decline in this measure of energy-holding capacity for 30 kWh variants. At two years of age, the mean rate of decline of SoH of 30 kWh Leafs was 9.9% per annum (95% uncertainty interval of 8.7% to 11.1%; n = 82). This was around three times the rate of decline of 24 kWh Leafs which at two years averaged 3.1% per annum (95% uncertainty interval of 2.9% to 3.3%; n = 201). For both variants there was evidence for an increasing rate of decline as they aged, although this was much more pronounced in the 30 kWh Leafs. Higher use of rapid DC charging was associated with a small decrease in SoH. Additionally, while 24 kWh cars with greater distances travelled showed a higher SoH, in 30 kWh cars there was a reduction in SoH observed in cars that had travelled further. The 30 kWh Leafs sourced from United Kingdom showed slower initial decline than those from Japan, but the rate of decline was similar at two years of age. Improvements in the battery health diagnostics, continuous monitoring of battery temperatures and state of charge, and verification of a fundamental model of battery health are needed before causes and remedies for the observed decline can be pinpointed. If the high rate of decline in battery capacity that we observed in the first 2.3 years of a 30 kWh Leaf’s lifetime were to continue, the financial and environmental benefits of this model may be significantly eroded. Despite 30 kWh Leafs accounting for only 14% of all light battery electric vehicles registered for use on New Zealand roads at the end of February 2018, there is also the potential for the relatively poor performance of this specific model to undermine electric vehicle uptake more generally unless remedies can be found.

Wetlands benefits can be summarized but are not limited to their ability to store floodwaters and improve water quality, providing habitats for wildlife and supporting biodiversity, as well as aesthetic values. Over the past few decades, remote sensing and geographical information technologies has proven to be a useful and frequent applications in monitoring and mapping wetlands. Combining both optical and microwave satellite data can give significant information about the biophysical characteristics of wetlands and wetlands` vegetation. Also, fusing data from different sensors, such as radar and optical remote sensing data, can increase the wetland classification accuracy. In this paper we investigate the ability of fusion two fine spatial resolution satellite data, Sentinel-2 and the Synthetic Aperture Radar Satellite, Sentinel-1, for mapping wetlands. As a study area in this paper, Balikdami wetland located in the Anatolian part of Turkey has been selected. Both Sentinel-1 and Sentinel-2 images require pre-processing before their use. After the pre-processing, several vegetation indices calculated from the Sentinel-2 bands were included in the data set. Furthermore, an object-based classification was performed. For the accuracy assessment of the obtained results, number of random points were added over the study area. In addition, the results were compared with data from Unmanned Aerial Vehicle collected on the same data of the overpass of the Sentinel-2, and three days before the overpass of Sentinel-1 satellite. The accuracy assessment showed that the results significant and satisfying in the wetland classification using both multispectral and microwave data. The statistical results of the fusion of the optical and radar data showed high wetland mapping accuracy, with an overall classification accuracy of approximately 90% in the object-based classification. Compared with the high resolution UAV data, the classification results give promising results for mapping and monitoring not just wetlands, but also the sub-classes of the study area. For future research, multi-temporal image use and terrain data collection are recommended.

In cricket, particularly the twenty20 format is most watched and loved by the people, where no one can guess who will win the match until the last ball of the last over. In India, The Indian Premier League (IPL) started in 2008 and now it is the most popular T20 league in the world. So we decided to develop a machine learning model for predicting the outcome of its matches. Winning in a Cricket Match depends on many key factors like a home ground advantage, past performances on that ground, records at the same venue, the overall experience of the players, record with a particular opposition, and the overall current form of the team and also the individual player. This paper briefs about the key factors that affect the result of the cricket match and the regression model that best fits this data and gives the best predictions. Cricket, the mainstream and widely played sport across India which has the most noteworthy fan base. Indian Premier League follows 20-20 format which is very unpredictable. IPL match predictor is a ML based prediction approach where the data sets and previous stats are trained in all dimensions covering all important factors such as: Toss, Home Ground, Captains, Favorite Players, Opposition Battle, Previous Stats etc, with each factor having different strength with the help of KNIME Tool and with the added intelligence of Naive Bayes network and Eulers strength calculation formula.

In this paper analyses the characteristic of EM waves propagation in structured environment to identify the signal interference by the structure, and suggests the EM waves attenuation model considering the distance and penetration loss by the structure. The range sensor based on electromagnetic(EM) waves attenuation along to the distance showed the precise distance estimation with high resolution depending on the distance. However, it is hard to use in structured environments due to the lack of consideration of the EM waves attenuation characteristics in the structured underwater environment. In this paper, EM waves propagation characteristic and signal interference effects by the structures were analyzed, and the EM waves distance-attenuation model in structured environment was suggested with sensor installation guideline. The EM waves propagation characteristics and proposed sensor model were verified by the several experiments, and the localization result in structured environment showed the more reliable performance.

Network Simulators is typically used to study services and applications in complex scenarios due to the infeasibility of deploying real testbeds. Many problems can be solved by using network simulators such as NS-3. With this in mind, the aim of this article is to introduce new NS-3 users through detailed information. It is sometimes difficult to handle by new users the traditional manuals developed by NS-3 project official website. In this article, NS-3 for communication network and Eclipse Integrated Development Environment (IDE) for powerful programming language are integrated step-by-step, explaining the main features of these open source software packages and concluding with an example simulation. Our effort is to make it easy for a beginner to be part of the NS-3 research community and to maintain an open environment of knowledge.

The production of lithium-ion battery cells is characterized by a high degree of complexit due to numerous cause-effect relationships between process characteristics. Knowledge about the multi-stage production is spread among several experts, rendering tasks such as failure analysis challenging. In this paper, a method is presented, which includes expert knowledge acquisition in production ramp-up by combining Failure Mode and Effects Analysis (FMEA) with a Bayesian Network. We show the effectiveness of this holistic method by building up a large scale, cross-process Bayesian Failure Network in lithium-ion battery production. Using this model, we are able to conduct root cause analyses as well as analyses of failure propagation. The former support operators in identifying root causes once a cell possesses a specific failure by calculating most-probable explanations matched to the individual battery cell data. The latter enable us to analyze propagation of failures and deviations in the production chain and thus provide support for placement of quality gates, leading to a significant reduction in scrap rate. Moreover, it gives an insight into which process steps are key drivers for which final product characteristics.

The emerging use of visualization techniques in pathology and microbiol- ogy has been accelerated by machine learning (ML) approaches towards image preprocessing, classification, and feature extraction in an increasingly complex series of datasets. Modern Convolutional Neural Network (CNN) architectures have developed into an umbrella of vast image reinforcement and recognition methods, including a combined classification-localization of single/multi-object featured images. As a subtype neural network, CNN cre- ates a rapid order of complexity by initially detecting borderlines, edges, and colours in images for dataset construction, eventually capable in mapping intricate objects and conformities. This paper investigates the disparities between Tensorflow object detection APIs, exclusively, Single Shot Detector (SSD) Mobilenet V1 and the Faster RCNN Inception V2 model, to sample computational drawbacks in accuracy-precision vs. real time visualization capabilities. The situation of rapid ML medical image analysis is theoretically framed in regions with limited access to pathology and disease prevention departments (e.g. 3rd world and impoverished countries). Dark field mi- croscopy datasets of an initial 62 XML-JPG annotated training files were processed under Malaria and Syphilis classes. Model trainings were halted as soon as loss values were regularized and converged.

The COVID-2019 disease caused by the SARS-CoV-2 virus (aka 2019-nCoV) has raised significant health concerns in China and worldwide. While novel drug discovery and vaccine studies are long, repurposing old drugs against the COVID-2019 epidemic can help identify treatments, with known preclinical, pharmacokinetic, pharmacodynamic, and toxicity profiles, which can rapidly enter Phase 3 or 4 or can be used directly in clinical settings. In this study, we presented a novel network based drug repurposing platform to identify potential drugs for the treatment of COVID-2019. We first analysed the genome sequence of SARS-CoV-2 and identified SARS as the closest disease, based on genome similarity between both causal viruses, followed by MERS and other human coronavirus diseases. Using our AutoSeed pipeline (text mining and database searches), we obtained 34 COVID-2019-related genes. Taking those genes as seeds, we automatically built a molecular network for which our module detection and drug prioritization algorithms identified 24 disease-related human pathways, five modules and finally suggested 78 drugs to repurpose. Following manual filtering based on clinical knowledge, we re-prioritized 30 potential repurposable drugs against COVID-2019 (including pseudoephedrine, andrographolide, chloroquine, abacavir, and thalidomide) . We hope that this data can provide critical insights into SARS-CoV-2 biology and help design rapid clinical trials of treatments against COVID-2019.

Over the past few decades, aircraft Ground Handling Operations (GHO) have been investigated by numerous researchers. Some aspects of GHO have been more focused on than others due to their importance in the GH processes. For instance, GHO performance has been tackled from different perspectives while workers and vehicles allocation suffer from the lack of research in the area. This paper is a literary review of the research that has been conducted in different areas of GHO. It sheds light on GHO performance, resource allocation and scheduling, operations scheduling, vehicle routing, and workers and vehicles allocation.

Structure from Motion with Multi-View Stereo photogrammetry (SfM) is increasingly utilised in geoscience investigations as a cost-effective method of acquiring high resolution (sub-meter) topographic data, but has not been thoroughly tested in gullied savanna systems. The aim of this study was to test the accuracy of topographic models derived from aerial (via an Unmanned Aerial Vehicle, ‘UAV’) and ground-based (via a handheld digital camera, ‘Ground’) SfM in modelling a hillslope gully system in dry-tropical savanna, and to assess the strengths and limitations of the approach at different scales. A UAV survey covered an entire hillslope gully system (0.715 km²), whereas a Ground survey covered a single gully within the broader system (650 m²). SfM topographic models, including Digital Surface Models (DSM) and dense point clouds, were compared against RTK-GPS point data and a pre-existing airborne LiDAR Digital Elevation Model (DEM). Results indicate UAV SfM can deliver topographic models with a resolution and accuracy suitable to define gully systems at a hillslope scale (e.g., 0.1 m resolution with ~ 0.5 – 1.3 m elevation error), while ground-based SfM is more capable of quantifying gully morphology (e.g., 0.01 m resolution with ~ 0.1 m elevation error). Key strengths of SfM for these applications include: the production of high resolution 3D topographic models and ortho-photo mosaics, low survey instrument costs (< $AUD 3,000); and rapid survey time (4 and 2 hours for UAV and Ground survey respectively). Current limitations of SfM include: difficulties in reconstructing vegetated surfaces; uncertainty as to optimal survey and processing designs; and high computational demands. Overall, this study has demonstrated great potential for SfM to be used as a cost-effective tool to aid in the mapping, modelling and management of hillslope gully systems at different scales, in tropical savanna landscapes and elsewhere.

This paper deals with the techno-economic study of the hybrid renewable energy system based on energy storage aspect under the form of hydrogen and methane. Indeed, with the intermittency of the renewable energy sources such as photovoltaic and wind energy, several problems of produced energy injection to the power system network can be encountered due to the shortage or the excess of these sources. This situation appeals the use of systems that ensure the stability of network based on the storage of energy surplus into gas using electrolyzer systems, which will be used afterward to cover the eventual shortage. In the present paper, the study of performance of each pathway of methane and hydrogen storage has been performed by the treatment of multiple scenarios via different architecture case studies in an Algerian location. Whereas, the energy produced by the photovoltaic system, the wind energy and the gas micro turbine sources are considered similar in each case. The modeling and simulation of the studied system operation under optimization criteria has been performed in this work, where the main aim is to define the appropriate configuration taking into account the different with low costs of investment, maintenance operation and immediate reactivity with a big storage capacity.

Nowadays, network simulators are frequently used to study services, applications and to solve problems in complex scenarios of communications. For this reason, the objective of this article is to introduce detailed information about installation of OMNET++ to new users. In this report, we show how to install OMNET++ simulator over a widely used distribution of Linux and how to integrate "Inet", "Inetmanet" and "Veins" frameworks with the simulator. We take care to explain this integration step-by-step. This tutorial includes: a virtual machine as additional material. Our objective is make it easy for a beginner research community in OMNET++ and to maintain an open environment of knowledge.

Recent methodological advances have enabled researchers to track the network structure of the human brain over time. Together, these studies provide novel insights into effective brain function, highlighting the importance of the systems-level perspective in understanding the manner in which the human brain organizes its activity to facilitate behavior. Here, we review a range of recent fMRI and electrophysiological studies that have mapped the relationship between inter-regional communication and network structure across a diverse range of brain states. In doing so, we identify both behavioral and biological axes that may underlie the tendency for network reconfiguration. We conclude our review by providing suggestions for future research endeavors that may help to refine our understanding of the functioning of the human brain.

Deep learning (DL), which is originated from an artificial neural network (ANN), is one of the major technologies of today's smart cybersecurity systems or policies to function in an intelligent manner. Popular deep learning techniques, such as Multi-layer Perceptron (MLP), Convolutional Neural Network (CNN or ConvNet), Recurrent Neural Network (RNN) or Long Short-Term Memory (LSTM), Self-organizing Map (SOM), Auto-Encoder (AE), Restricted Boltzmann Machine (RBM), Deep Belief Networks (DBN), Generative Adversarial Network (GAN), Deep Transfer Learning (DTL or Deep TL), Deep Reinforcement Learning (DRL or Deep RL), or their ensembles and hybrid approaches can be used to intelligently tackle the diverse cybersecurity issues. In this paper, we aim to present a comprehensive overview from the perspective of these neural networks and deep learning techniques according to today's diverse needs. We also discuss the applicability of these techniques in various cybersecurity tasks such as intrusion detection, identification of malware or botnets, phishing, predicting cyber-attacks, e.g. denial of service (DoS), fraud detection or cyber-anomalies, etc. Finally, we highlight several research issues and future directions within the scope of our study in the field. Overall, the ultimate goal of this paper is to serve as a reference point and guidelines for the academia and professionals in the cyber industries, especially from the deep learning point of view.

Noise reduction in medical images is a perplexing undertaking for the researchers in digital image processing. Noise generates maximum critical disturbances as well as touches the medical images quality, ultrasound images in the field of biomedical imaging. The image is normally considered as gathering of data and existence of noises degradation the image quality. It ought to be vital to reestablish the original image noises for accomplishing maximum data from images. Medical images are debased through noise through its transmission and procurement. Image with noise reduce the image contrast and resolution, thereby decreasing the diagnostic values of the medical image. This paper mainly focuses on Gaussian noise, Pepper noise, Uniform noise, Salt and Speckle noise. Different filtering techniques can be adapted for noise declining to improve the visual quality as well as reorganization of images. Here four types of noises have been undertaken and applied on medical images. Besides numerous filtering methods like Gaussian, median, mean and Weiner applied for noise reduction as well as estimate the performance of filter through the parameters like mean square error (MSE), peak signal to noise ratio (PSNR), Average difference value (AD) and Maximum difference value (MD) to diminish the noises without corrupting the medical image data.

With the increase of the Artificial Neural Network (ANN), machine learning has taken a forceful twist in recent times. One of the most spectacular kinds of ANN design is the Convolutional Neural Network (CNN). The Convolutional Neural Network (CNN) is a technology that mixes artificial neural networks and up to date deep learning strategies. In deep learning, Convolutional Neural Network is at the center of spectacular advances. This artificial neural network has been applied to several image recognition tasks for decades and attracted the eye of the researchers of the many countries in recent years as the CNN has shown promising performances in several computer vision and machine learning tasks. This paper describes the underlying architecture and various applications of Convolutional Neural Network.

Human detection from Unmanned Aerial Vehicles (UAV) is gaining popularity in the field of disaster management, crowd counting, people monitoring. Real time human detection from UAV is a challenging task, because of many constraints involved. This study proposes a system for real time detection of humans on videos captured from UAVs addressing three of these constraints namely, flying height, computation time and scale of viewing. The proposed method integrated an android application with a binary classifier based on Haar-features to automatically detect human / non-human class from UAV images. The video frames were parsed and detected humans from image frames were geo-localized and visualized on Google Earth. The performance was evaluated for geo-localization accuracy, computation time and detection accuracy, considering human coverage – pixel size relationship for various heights and scale factor. Based on flying height - human size relationship and tradeoff between detection accuracy vs computation time, the study came up with optimal parameters for OpenCV’s cv2.cascadeClassifier. detectMultiScale function. This paper establishes a strong ground for further research relating to real time human detection from UAV.

Automotive aerodynamics comprises of the study of aerodynamics of road vehicles. Its main goals are reducing drag, minimizing noise emission, improving fuel economy, preventing undesired lift forces and minimizing other causes of aerodynamic instability at high speeds. The Ahmed body has the form of a highly simplified car, consisting of a blunt nose with rounded edges fixed onto a box-like middle section and a rear end that has an upper slanted surface, the angle of which can be varied. It retains vital features of real vehicles in order to study the flow fields around it and the related turbulence models which characterizes the actual flow at elevated Reynolds number. In the present study, the aerodynamic behavior of this body is investigated numerically by the aid of commercial CFD tool: Ansys Fluent. The results of the simulation are validated with available experimental data and results of the simulations from other literatures. The numerical data were obtained for a fixed free stream velocity of 25 m/s at the inlet. The simulations were performed at a fixed slant angle of 25 degree and zero yaw angle. The present study focuses on how local refinement of mesh inside the concerned body and the outside, helps affect the results and for which grid dependency test is the primary objective of this paper. The present study also helps demonstrate how the drag of the body behaves, which is mainly the effect of pressure drag force generated at the rear portion of the body. The study also focuses on important properties like the velocity magnitude at different locations for different meshing cases, and to capture the flow pattern in the front or near the wake region. The study can be further helpful to future researchers in determining resistance, fuel efficiency etc. helping designers to optimize in specialized areas for better efficiency.

In this paper, the current technologies of the regenerative shock absorber systems have been categorized and evaluated. Three drive modes of the regenerative shock absorber systems, namely the direct drive mode, the indirect drive mode and hybrid drive mode are reviewed for their readiness to be implemented. The damping performances of the three different modes are listed and compared. Electrical circuit and control algorithms have also been evaluated to maximize the power output and to deliver the premium ride comfort and handling performance. Different types of parameterized road excitations have been applied to vehicle suspension systems to investigate the performance of the regenerative shock absorbers including that of the nonlinear regenerative shock absorber. The research gaps for comparison of the different drive modes and the nonlinearity analysis of the regenerative shock absorbers are identified and, the corresponding research questions have been proposed for future work.

Since the Coronavirus disease (COVID-19) outbreak at the end of 2019, the past two month has seen an acceleration both in and outside China in the R&D of the diagnostics, vaccines and therapeutics for this novel coronavirus. As one of the molecular forces that determine protein structure, electrostatic effects dominate many aspects of protein behaviour and biological function. Thus, incorporating currently available experimental structures related to COVID-19, this article reports a simple python-based analysis tool and a LaTeX-based editing tool to extract and summarize the electrostatic features from experimentally determined structures, to strengthen our understanding of COVID-19's structure and function and to facilitate machine-learning and structure-based computational design of its neutralizing antibodies and/or small molecule(s) as potential therapeutic candidates. Finally, this article puts forward a brief update of the structurally observed electrostatic features of the COVID-19 coronavirus.

Small and micro hydropower represents an attractive solution for electricity generation, with low cost and low environmental impact. The pump-as-turbine (PAT) approach has promise in this application owing to its low purchase and maintenance costs. In this paper, a new method to predict the inverse characteristic of industrial centrifugal pumps is presented. This method is based on results of simulations performed with commercial three-dimensional CFD software. Model results have been first validated in pumping mode using data supplied by pump manufacturers. Then, results have been compared to experimental data for a pump running in reverse condition. Experimentation has been performed on a dedicated test bench installed in the Department of Civil Construction and Environmental Engineering of the University of Naples Federico II. Three different pumps, with different specific speeds, have been analyzed. Using the model results, the inverse characteristic and the best efficiency point have been evaluated. Finally, results of this methodology have been compared to prediction methods available in the literature.

This paper presents an overview of the smart electro-clothing systems (SeCSs) targeted at health monitoring, sports benefits, fitness tracking, and social activities. Technical features of the available SeCSs, covering both textile and electronic components, are thoroughly discussed and their applications in the industry and research purposes have been highlighted. In addition, it also presents the developments in the associated areas of wearable sensor systems and textile-based dry sensors. As it became evident during the literature research, such a review on SeCSs covering all relevant issues has not been presented before. This paper will be particularly helpful for new generation researchers investigating the design, development, function and comforts of the sensor integrated clothing materials.

With the increased liberation of trade and fierce competition in the automotive industry, Proton needs to embark on a strategic reform to survive and remain relevant in the challenging market. This case study aims to explain the effectiveness of the Post Geely acquisition's ten years master plan to enhance Proton's self-reliance and global competitiveness. This case suggests that while the company's ten-year Master Plan is holistic and shows positive results in the early years, there is a need for a new business strategy, given the challenges imposed by climate change's impact on the automotive industry moving forward. The potentials of the Electric Vehicles (EVs) market and the Internet of Things (IoT) to develop the necessary long-term competitive advantage. A market strategy integrating the 4Ps and 4Cs framework suggests a two-dimensional convergence of the market mix, incorporating the organization's market strategy with a more consumer expectations-centric and user experience. Strategic integration of Geely's technological assets in developing Proton's technical know-how can address Proton's challenges and opportunities ahead.

The Bayes filters, such as Kalman and particle filters, have been used in sensor fusion to integrate two sources of information and obtain the best estimate of the unknowns. Efficient integration of multiple sensors requires deep knowledge of their error sources and it is not trivial for complicated sensors, such as Inertial Measurement Unit (IMU). Therefore, IMU error modelling and efficient integration of IMU and Global Navigation Satellite System (GNSS) observations has remained a challenge. In this paper, we develop deep Kalman filter to model and remove IMU errors and consequently, improve the accuracy of IMU positioning. In other words, we add modelling step to the prediction and update steps of Kalman filter and the IMU error model is learned during integration. Therefore, our deep Kalman filter outperforms Kalman filter and reaches higher accuracy.

Alvar Aalto created innovative architecture in his breakthrough work, Paimio Sanatorium, located in Southwestern Finland and designed between 1928 and 1933. The technological systems in construction, such as the concrete frame, electricity, air conditioning, and lifts, developed rapidly in the interwar period and Aalto drew influences from the culturally radical modernistic discourse around the CIAM organisation and felt that architecture should respond to the demands of the age. Architecture is an applied form of art, and symbolic expression in architecture is a system with its logic. As a contrast, a building is a technological system and forms a framework within which to solve practical problems. Thus, as a technological system, the building is both material and social, during its construction and after. The theoretical underpinning for the study was the actor-network theory developed since the 1980s by the French sociologist Bruno Latour. This study clearly showed the importance of a collaborative effort in a building project. The most famous architectural solutions for Paimio Sanatorium, a demanding institutional building project, came into being in circumstances where the architect-innovator, Aalto, managed to create a viable and robust hybrid that merged collective competence with material factors.

The concept of a Social License to Operate (SLO) has become increasingly important in the sustainability literature in recent years. Having its origins in the business discourse of the mining industry with respect to limiting opposition to mining projects, the notion of a social contract above and beyond legal requirements has since become applied across a number of different industries. Despite the concepts adoption confusion exists over the practices and outcomes of SLO, and particularly the nature of engagement. Given this situation it is surprising that not more attention to the role of marketing, and social marketing in particular, in operationalizing the concept. The paper discusses the potential of social marketing to contribute to SLO. Economic, political and social relations are complex in SLO and exchange is intricate in such relational environments. A community-based social marketing orientation is proposed as a means to improve exchange relations and enhance engagement. Seven models of SLO related social marketing models are discussed with community-based social marketing and adaptive co-marketing models being regarded as the most positive for the achievement of an SLO. Potential barriers to adoption of these approaches are noted.

The use of Light Amplification by Stimulated Emission of Radiation (i.e., LASERs or lasers) by the U.S. Department of Defense is not new and includes laser weapons guidance, laser-aided measurements, even lasers as weapons (e.g., Airborne Laser). Lasers in support of telecommunications is also not new. The use of laser light in fiber optics shattered thoughts on communications bandwidth and throughput. Even the use of lasers in space is no longer new. Lasers are being used for satellite-to-satellite crosslinking. Laser communication can transmit orders-of-magnitude more data using orders-of-magnitude less power and can do so with minimal risk of exposure to the sending and receiving terminals. What is new is using lasers as the uplink and downlink between the terrestrial segment and the space segment of satellite systems. More so, the use of lasers to transmit and receive data between moving terrestrial segments (e.g., ships at sea, airplanes in flight) and geosynchronous satellites is burgeoning. This manuscript examines the technological maturation of employing lasers as the signal carrier for satellite communications linking terrestrial and space systems. The purpose of the manuscript is to develop key performance parameters (KPPs) to inform U.S. Department of Defense initial capabilities documents (ICDs) for near-future satellite acquisition and development. By appreciating the history and technological challenges of employing lasers rather than traditional radio frequency sources for satellite uplink and downlink signal carrier, this manuscript recommends ways for the U.S. Department of Defense to employ lasers to transmit and receive high bandwidth, large-throughput data from moving platforms that need to retain low probabilities of detection, intercept, and exploitation (e.g., carrier battle group transiting to a hostile area of operations, unmanned aerial vehicle collecting over adversary areas). The manuscript also intends to identify commercial sector early-adopter fields and those fields likely to adapt to laser employment for transmission and receipt.

Recently, design of electric scooters (ESs) has commonly adopted brushless DC motors (BLDCMs) in place of brushed DC motors. This invention develops a new anti-lock braking system (ABS), based on a slip-ratio estimator, for ES utilizing the braking force generated by the BLDCM when electrical energy releases to the load yielding an analogous effect of ABS control in gas-engine vehicles. Comparing to mechanical ABS, the design possesses the advantages of rapid torque responses due to fast actuating response. The electrical ABS is realized by associating with kinematic and Short-circuit braking. A current controller is used to adjust the braking force, while the sliding mode control strategy is adopted to regulate the slip ratio for best road adhesion while braking. Real-world experiments have been conducted for functional and performance verification.

Security has become a critical issue in today’s highly distributed and networked systems. Network intrusion detection systems (NIDSs), especially signature-based NIDSs, are being widely deployed in a distributed network environment with the purpose of defending against a variety of network attacks. Most of the commercially available NIDSs are software based and rely on pattern matching to extract the threat from network traffic. The increase in network speed and traffic may make existing algorithms to become a performance bottleneck. Therefore it is very necessary to develop faster and more efficient pattern matching algorithm in order to overcome the troubles on performance of NIDSs. Therefore, we propose a multi fusion pattern matching algorithm for Network Intrusion Detection Systems. The results obtained in percentages from the proposed fusion algorithm given better values in terms processing time in milliseconds than the existing algorithms when data English text are applied to evaluate the fusion performances.

The technologies influencing alternative ways of transportation are augmenting in recent years as the need for transportation is increasing rapidly due to urbanization and motorization. In this paper, a solar powered electric auto-rickshaw (SPEA) is designed and developed for Indian conditions. The developed vehicle is comprehensively analyzed techno-economically for its viability in the Indian market. The performance analysis of SPEA results in an optimal charging rate of 2 kWh per day with an average solar irradiance of 325 W/m2. The discharging characteristics are studied based on different loading conditions. The vehicle achieved a maximum speed of 21.69 km/h with battery discharge rate of 296W at 90kg load and also reached a maximum discharge rate of 540W at 390kg loading with a maximum speed of 12.11 km/h. The environmental analysis of SPEA displayed yearly CO2 emissions of 1,777 kg, 1,987 kg and 1,938 kg using Compressed Natural Gas, Liquefied Petroleum Gas and gasoline engines respectively can be mitigated using SPEA. The results of financial analysis of SPEA were welcoming as the investor gets 24.44% lesser payback duration compared to gasoline run vehicle. Socio-Economic analysis of SPEA discussed its significant advantages and showed 18.73% and 3.9% increase in yearly income over gasoline driven and battery driven vehicles.

Music has the innate potential to reach all parts of the brain, stimulates certain brain areas which are not achievable through other modalities. Music Therapy (MT) is being used for more than a century to treat individuals who needs personalized care. MT optimizes motor, speech and language responsibilities of the brain and improves cognitive performance. Pervasive developmentdisorder (PDD) is a multifaceted, neuro developmental disorder and autism spectrum disorder (ASD) comes under PDD, which is defined by deficiencies in three principal spheres: social connection with others, communicative and normal movement skills. The conventional imaging studies illustrate reduced brain area connectivity in people with ASD, involving selected parts of the brain cortex. People with ASD express much interest in musical activities which engages the brain network areas and improves communication and social skills.The main objective of this review is to analyze the potential role of MT in treating the neurological conditions, particularly ASD. Evidence based studies have reported the extensive therapeutic application of music on various part of the brain in a nonverbal child with autism through hearing or making music.Hence we hypothesized that MT intervention can improve the communication capacity in people with ASD, than customary neurorestoration therapy alone.

The article’s goal is to overview challenges and problems on the way from the state of the art CUDA accelerated neural networks code to multi-GPU code. For this purpose, the authors describe the journey of porting the existing in the GitHub, fully-featured CUDA accelerated Darknet engine to OpenCL. The article presents lessons learned and the techniques that were put in place to make this port happen. There are few other implementations on the GitHub that leverage the OpenCL standard, and a few have tried to port Darknet as well. Darknet is a well known convolutional neural network (CNN) framework. The authors of this article investigated all aspects of the porting and achieved the fully-featured Darknet engine on OpenCL. The effort was focused not only on the classification with the use of YOLO1, YOLO2, and YOLO3 CNN models. They also covered other aspects, such as training neural networks, and benchmarks to look for the weak points in the implementation. The GPU computing code substantially improves Darknet computing time compared to the standard CPU version by using underused hardware in existing systems. If the system is OpenCL-based, then it is practically hardware independent. In this article, the authors report comparisons of the computation and training performance compared to the existing CUDA-based Darknet engine in the various computers, including single board computers, and, different CNN use-cases. The authors found that the OpenCL version could perform as fast as the CUDA version in the compute aspect, but it is slower in memory transfer between RAM (CPU memory) and VRAM (GPU memory). It depends on the quality of OpenCL implementation only. Moreover, loosening hardware requirements by the OpenCL Darknet can boost applications of DNN, especially in the energy-sensitive applications of Artificial Intelligence (AI) and Machine Learning (ML).

Deep neural networks (DNNs) have made a huge impact in the field of machine learning by providing unbeatable humanlike performance to solve real-world problems such as image processing and natural language processing (NLP). Convolutional neural network (CNN) and recurrent neural network (RNN) are two typical architectures that are widely used to solve such problems. Time sequence-dependent problems are generally very challenging, and RNN architectures have made an enormous improvement in a wide range of machine learning problems with sequential input involved. In this paper, different types of RNN architectures are compared. Special focus is put on two well-known gated-RNN’s Long Term Short Memory (LSTM) and Gated Recurrent Unit (GRU). We evaluated these models on the task of force estimation system in pouring. In this study, four different models including multi-layers LSTM, multi-layers GRU, single-layer LSTM and single-layer GRU) were created and trained. The result suggests that multi-layer GRU outperformed other three models.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

In daily travel and activities, pathfinding is a significant process. They are often used in transportation routes calculation. They have now evolved to be able to solve most situations of the pathfinding and its related problems. This review describes previous and recent studies on the pathfinding algorithms. It reviews the development of pathfinding algorithms in a classification base on their usage. The aim is to summarize the application of the pathfinding algorithms for the readers interested in the subject that can be used as a supplement.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Suicidal behaviour remains difficult to predict and prevent, even for experienced mental health care professionals. The known distal risk factors for suicidal behaviour are not sufficiently specific to fully understand the complex dynamic processes that precede a suicide attempt. Real-time mobile monitoring data can be used to analyse proximal risk mechanisms within the suicidal process. At the same time smartphone-based safety planning and self-monitoring may enhance a patient’s self-management skills thereby increasing their capacity to respond to a suicidal crisis and to become more aware of crisis symptoms. The current paper describes the theoretical and conceptual rationale for the CASPAR study which applies an innovative approach to the study of suicidal processes. It uses basic science approaches to inform the implementation of an innovative suicide prevention intervention. We aim to develop and implement mobile safety plan in conjunction with real-time monitoring in order to both directly implement suicide prevention interventions and to study the ongoing dynamics of individual suicidal behaviour by applying network analysis.

In the field of nasal delivery, one of the most fascinating applications is the delivery of drugs directly to the central nervous system bypassing the blood brain barrier. This approach would provide a series of benefits, such as dose lowering and direct targeting of potent drugs, ultimately reducing their systemic side effects. Recently, clinical trials have explored the nasal administration of insulin for the treatment of Alzheimer’s disease, with promising results. The use of nanomedicines could provide further options for making nose-to-brain delivery reality. In particular, apart from the selection of devices able to deposit the formulation in the upper part of the nose, surface modification of these nanomedicines appears the key strategy to optimize the delivery of drugs from the nasal cavity to the brain. In this review, nanomedicines delivery approaches based on surface electrostatic charges, mucoadhesive polymers, as well as chemical moieties targeting nasal epithelium, will be discussed and critically evaluated for nose-to-brain delivery.

The population’s mobility in urban areas is a necessary variable in the modeling of risk scenarios caused by atmospheric contamination. The inclusion of this concept makes static models more dynamic while considering people within a city to be an entity with complex mobility processes. We propose a conceptual and methodological tool to make the representation of the social, economic and territorial components, as well as the patterns in the population´s mobility to delimitate risk areas for human health by exposure of contaminants. In the volatile organic compounds (VOC), benzene, ethylbenzene, toluene and xylene (BTEX) are amongst the most dominant substances in fugitive vapor emissions in gas stations (GS). In urban areas, the exposure to BTEX by residential proximity and proximity to other facilities, which cause intra-urban agglomeration, can impact and affect human health. This model seeks to facilitate the focalization, identification and prioritization of risk areas by BTEX environmental contamination. This article goes beyond de conceptual framework. It suggests methodological and instrumental aspects to be applied in other cities. The government agencies must consider these results when establishing rules, permissions and procedures to reduce environmental pollution for managing the risk in a complex urban environment.

In the era when the market segment of Internet of Things (IoT) tops the chart in various business reports, it is apparently envisioned that the field of medicine expects to gain a large benefit from the explosion of wearables and internet-connected sensors that surround us to acquire and communicate unprecedented data on symptoms, medication, food intake, and daily-life activities impacting one’s health and wellness. However, IoT-driven healthcare would have to overcome many barriers, such as: 1) There is an increasing demand for data storage on cloud servers where the analysis of the medical big data becomes increasingly complex; 2) The data, when communicated, are vulnerable to security and privacy issues; 3) The communication of the continuously collected data is not only costly but also energy hungry; 4) Operating and maintaining the sensors directly from the cloud servers are non-trial tasks.This book chapter defined Fog Computing in the context of medical IoT. Conceptually, Fog Computing is a serviceoriented intermediate layer in IoT, providing the interfaces between the sensors and cloud servers for facilitating connectivity, data transfer, and queryable local database. The centerpiece of Fog computing is a low-power, intelligent, wireless, embedded computing node that carries out signal conditioning and data analytics on raw data collected from wearables or other medical sensors and offers efficient means to serve telehealth interventions. We implemented and tested an fog computing system using the Intel Edison and Raspberry Pi that allows acquisition, computing, storage and communication of the various medical data such as pathological speech data of individuals with speech disorders, Phonocardiogram (PCG) signal for heart rate estimation, and Electrocardiogram (ECG)-based Q, R, S detection. The book chapter ends with experiments and results showing how fog computing could lessen the obstacles of existing cloud-driven medical IoT solutions and enhance the overall performance of the system in terms of computing intelligence, transmission, storage, configurable, and security. The case studies on various types of physiological data shows that the proposed Fog architecture could be used for signal enhancement, processing and analysis of various types of bio-signals.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This project designed a set of network security mechanisms for cloud applications in VANETs. At present, cloud computing is one of the government’s development priorities in the industry. We divide cloud into public, private, and hybrid clouds in this project. Vehicles or passengers can access road conditions or public transport information through the public cloud; public transportation can access current driving records and users can access relevant enterprise information on the private cloud and hybrid cloud is a combination of public and private clouds. Both cloud computing or VANETs require network and information security. At present, many researches on VANETs security only focus on message communication, and neglect information storage. Researches on cloud computing security only focus on information protection, and neglect user privacy and anonymity. This project designed a set of network and information security mechanisms in line with the requirements of Confidentiality, Authentication, Non-repudiation, Conditional Anonymity, and Conditional Untraceability. This project primarily needs to achieve the following: 1.an authentication mechanism to verify the identity of each other between the passenger and the vehicle and to verify the identity with Single Sign-On; 2. vehicle or user privacy and anonymity, which need to be able to replace the anonymous ID and related parameters for the vehicle or the user; 3. a private communication mechanism, which enables any vehicle or user to communicate privately; and 4. an information security encryption method, which can encrypt the information on a cloud server to avoid unauthorized access by internal personnel or hackers.

Recent advancement of deep learning has been elevated the multifaceted nature in various applications of this field. Artificial neural networks are now turning into a genuinely old procedure in the vast area of computer science; the principal thoughts and models are more than fifty years of age. However, in this modern computing era, 3rd generation intelligent models are introduced by scientists. In the biological neuron, actual film channels control the progression of particles over the layer by opening and shutting in light of voltage changes because of inborn current flows and remotely led to signals. A comprehensive 3rd generation, Spiking Neural Network (SNN) is diminishing the distance between deep learning, machine learning, and neuroscience in a biologically-inspired manner. It also connects neuroscience and machine learning to establish high-level efficient computing. Spiking Neural Networks initiate utilizing spikes, which are discrete functions that happen at focuses as expected, as opposed to constant values. This paper is a review of the biological-inspired spiking neural network and its applications in different areas. The author aims to present a brief introduction to SNN, which incorporates the mathematical structure, applications, and implementation of SNN. This paper also represents an overview of machine learning, deep learning, and reinforcement learning. This review paper can help advanced artificial intelligence researchers to get a compact brief intuition of spiking neural networks.

This article presents an automated vision-based algorithm for the die-scale inspection of wafer images captured using scanning acoustic tomography (SAT). This algorithm can find defective and abnormal die-scale patterns, and produce a wafer map to visualize the distribution of defects and anomalies on the wafer. The main procedures include standard template extraction, die detection through template matching, pattern candidate prediction through clustering, and pattern classification through deep learning. To conduct the template matching, we first introduce a two-step method to obtain a standard template from the original SAT image. Subsequently, a majority of the die patterns are detected through template matching. Thereafter, the columns and rows arranged from the detected dies are predicted using a clustering method; thus, an initial wafer map is produced. This map is composed of detected die patterns and predicted pattern candidates. In the final phase of the proposed algorithm, we implement a deep learning-based model to determine defective and abnormal patterns in the wafer map. The experimental results verified the effectiveness and efficiency of our proposed algorithm. In conclusion, the proposed method performs well in identifying defective and abnormal die patterns, and produces a wafer map that presents important information for solving wafer fabrication issues.

Topology optimization is a pioneering design method that can provide various candidates with high mechanical properties. However, the high-resolution for the optimum structures is highly desired, normally in turn leading to computationally intractable puzzle, especially for the famous Solid Isotropic Material with Penalization (SIMP) method. In this paper, an efficient and high-resolution topology optimization method is proposed based on the Super-Resolution Convolutional Neural Network (SRCNN) technique in the framework of SIMP. The SRCNN includes four processes, i.e. refining, path extraction & representation, non-linear mapping, and reconstruction. The high computational efficiency is achieved by a pooling strategy, which can balance the number of finite element analysis (FEA) and the output mesh in optimization process. To further reduce the high computational cost of 3D topology optimization problems, a combined treatment method using 2D SRCNN is built as another speeding-up strategy. A number of typical examples justify that the high-resolution topology optimization method adopting SRCNN has excellent applicability and high efficiency for 2D and 3D problems with arbitrary boundary conditions, any design domain shape, and varied load.

Integration of multi-view datasets which are comprised of heterogeneous sources or different representations is challenging to understand the subtle and complex relationship in data. Such data integration methods attempt to combine efficiently the complementary information of multiple data types to construct a comprehensive view of underlying data. Nonnegative matrix factorization (NMF), an approach that can be used for signal compression and noise reduction, has aroused widespread attention in the last two decades. The Kullback–Leibler divergence (or relative entropy) information distance can be used to measure the loss function of NMF. In this article, we propose a fast and robust framework (RSNMF) based on symmetric nonnegative matrix factorization (SNMF) and similarity network fusion (SNF) for clustering human microbiome data including functional, metabolic and phylogenetic profiles. Many existing methods typically utilize all the information provided by each view to create a consensus representation, which often suffers a lot from noise in data and cannot provide a precise representation of the latent data structures. In contrast, RSNMF combines the strength of SNMF and the advantage of SNF to form a robust clustering indicator matrix thus can reduce the noise influence. We conduct experiments on one synthetic and two real dataset (microbiome data, text data) and the results show that the proposed RSNMF has better performance over the baseline and the state-of-art methods, which demonstrates the potential application of RSNMF for microbiome data analysis.

Unmanned Aerial Vehicles (UAVs) are now filling in the gaps between spaceborne and ground-based observations and enhancing the spatial resolution and temporal coverage of data acquisition. In the realm of hydrological observations, UAVs have a key role to quantitatively characterize the surface flow allowing for remotely accessing the water body of interest. In this paper we propose a technology which uses a sensing platform encompassing a drone and a camera to determine the water level. The images acquired my means of the sensing platform are then analyzed using the Canny method to detect the edges of water level and of Ground Control Points (GCPs) used as reference points. The water level is then retrieved from images and compared to a benchmark value obtained by a traditional device. The method is tested at four locations in an artificial lake in central Italy. Results are encouraging as the overall mean error between estimated and true water level values is around 0.02 m. This technology is well suited to improve hydraulic modeling and thus provide a reliable support to flood mitigation strategies also in uneasy-to-access environments.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

Whereas waste management research has focused on mostly urban municipalities in South Africa, not much is known about the current performance of waste management services from the perspective of community residents in rural municipalities. This study reports on the status and effectiveness of waste management practices from the perspective of community residents in the Umkhanyakude and Zululand Districts in the rural areas of the KwaZulu-Natal province of South Africa. Making use of structured questionnaires, primary data was obtained by interviewing 333 respondents representing households in the study area. Results have revealed several shortfalls in the provision of municipal waste management services, except for solid waste removal from households (66%), and management of landfill sites (41%). The degree of dissatisfaction for waste management services rendered was very high (97.3%). Furthermore, the majority (61.4%) of respondents were not willing to participate in waste segregation due to lack of appropriate knowledge and infrastructure. The study also pinpointed some benefits associated with waste minimization, as well as barriers constraining effective waste recycling. Based on these findings, there is a dire need for transforming current waste management practices toward increased recycling rates by creating more environmental awareness and a supporting infrastructure.

Intracellular aggregates of the alpha-synuclein protein result in cell loss and dysfunction in Parkinson’s disease and atypical parkinsonism, such as multiple system atrophy and dementia with Lewy bodies. Each of these neurodegenerative conditions, known collectively as alpha-synucleinopathies, may be characterized by a different suite of molecular triggers that initiate pathogenesis. The mechanisms whereby alpha-synuclein aggregates in turn mediate cytotoxicity also remain to be fully elucidated. However, recent studies have implicated the cell-to-cell spread of alpha-synuclein as the major mode of disease propagation between brain regions during disease progression. Here, we review the current evidence for different modes of alpha-synuclein cellular release, movement and uptake, including exocytosis, exosomes, tunnelling nanotubes, glymphatic flow and endocytosis. A more detailed understanding of the major modes by which alpha-synuclein pathology spreads throughout the brain may provide new targets for therapies that halt the progression of disease.

Vehicle to vehicle (V2V) and Vehicle to infrastructure (V2I) or briefly V2X communications are the one of hot topics in automotive industry. Therefore, this situation is providing many advantages of connected vehicles and infrastructures which bring to human life. For instance, vehicles and road infrastructures which shares information with each other, provides a neat flow regulation, more ordered traffic flow and therefore jammed traffic dependent accident’s percentage will be decreased. On the other hand, security is the most important issue for these systems because the operation of V2X networks is completely dependent on uninterrupted and accurate information sharing. In the light of these information, in this paper we review security issues and current solution architectures. We also propose some open problems in this lively field.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

Lily tepals have a short lifespan. Once the tepals senesce, the ornamental value of the flower is lost. Some cultivars have attractive purple ovaries and fruits which greatly enhance the ornamental value of Asiatic hybrid lilies. However, little is known about the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries. To investigate the transcriptional network that governs purple ovary coloration in Asiatic hybrid lilies, we obtained transcriptome data from green ovaries (S1) and purple ovaries (S2) of Asiatic ‘Tiny Padhye’. Comparative transcriptome analysis revealed 4228 differentially expressed genes. Differential expression analysis revealed that nine unigenes including four CHS genes, one CHI gene, one F3H gene, one F3′H gene, one DFR gene, and one UFGT gene were significantly up-regulated in purple ovaries. One MYB gene, LhMYB12-Lat, was identified as a key transcription factor determining the distribution of anthocyanins in Asiatic hybrid lily ovaries. Further qPCR results showed unigenes related to anthocyanin biosynthesis were highly expressed in purple ovaries of Asiatic ‘Tiny Padhye’ at stages 2 and 3, while they showed an extremely low level of expression in ovaries of Asiatic ‘Yellow Pixels’ during all developmental stages. In addition, shading treatment significantly decreased pigment accumulation by suppressing the expression of several unigenes related to anthocyanin biosynthesis in ovaries of Asiatic ‘Tiny Padhye’. These results could further our understanding of the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries.

The present grievous situation of the tuberculosis disease can be improved by efficient case management and timely follow-up evaluations. With the advent of digital technology this can be achieved by quick summarization of the patient-centric data. The aim of our study was to assess the effectiveness of the ODK Scan paper-to-digital system during testing period of three months. A sequential, explanatory mixed-method research approach was employed to elucidate technology use. Training, smartphones, application and 3G enabled SIMs were provided to the four field workers. At the beginning, baseline measures of the data management aspects were recorded and compared with endline measures to see the impact of ODK Scan. Additionally, at the end, users’ feedback was collected regarding app usability, user interface design and workflow changes. 122 patients’ records were retrieved from the server and analysed for quality. It was found that ODK Scan recognized 99.2% of multiple choice bubble responses and 79.4% of numerical digit responses correctly. However, the overall quality of the digital data was decreased in comparison to manually entered data. Using ODK Scan, a significant time reduction is observed in data aggregation and data transfer activities, however, data verification and form filling activities took more time. Interviews revealed that field workers saw value in using ODK Scan, however, they were more concerned about the time consuming aspects of the use of ODK Scan. Therefore, it is concluded that minimal disturbance in the existing workflow, continuous feedback and value additions are the important considerations for the implementing organization to ensure technology adoption and workflow improvements.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

Multiple sensor nodes known as detection stations make the sensor networks; each node is light and portable. Every sensor node contains power source, microcomputer, transducer and transceiver. Power source provides power to each node. Micro-computer is used for storing and processing the output coming from the sensors. The transducer is used to generate the signals and the transceiver is used to receive and transmit data to the central computer. Eavesdropping gets facilitated with wireless communication, and it has many useful applications in military, homeland, hostile and uncontrolled environments. So it is prone to the high level of security. The process in which information is gathered to form a summarized type for analysis is known as data aggregation, as it is used to reduce the energy consumption in wireless sensor networks. The security issues have become crucial in data aggregation, especially when gets deployed in hostile and remote environment. In wireless sensor networks many secure aggregations have been proposed. It still faces some resource constrained that’s why new techniques are needed. In our survey we will discuss those approaches and their pros and cons.

Neural networks models are mostly represented by oriented graphs where only the components, constitutive elements of the graph, are transcribed into mathematical xpression. Indeed, accurate knowledge of the full expression of the model is required in certain situations such as selecting among several reference models, the one that best fits the available data or comparing the explanatory and predictive performance of an established model with respect to some reference models. In this paper, we establish a formalism of the mathematical expression for multilayer perceptron neural network in a general framework, MLP-p-n-q, with p, n and q natural integers and show its restriction to cases where one has a hidden layer and multivariate outputs (MLP-p-1-q), and then a single output (MLP-p-1-1). Then, we give some specific cases of the most commonly used models. An application case is presented in the context of solving a nonlinear regression problem.

Sustainable food consumption has attracted a widespread attention during last decades by scholars, policy makers and consumers. In line with this, farmers’ markets (FMs) have the potential to encourage sustainable agricultural production and consumption. By reducing the number of actors and distances along the food chain, these alternative food systems foster the reconnection between farmers and consumers and contribute to different social, economic and environmental sustainable goals. This paper provides insights on the role of consumers' sustainability concerns related to their motivation for shopping at FMs. By means of a choice experiment, we analyze the determinants of consumers’ WTP for buying apples at FMs. We are particularly interested in understanding how attitudes towards the three sustainability dimensions are related to consumer preferences in this context. We find that consumer attitudes towards direct contact with producers, contributing to farmers’ income, and environmental benefits can be directly related to product characteristics that are specific to FMs.

Cronbach’s (1957) famous division of scientific psychology into two disciplines is still actual for the fields of cognition (general mechanisms) and intelligence (dimensionality of individual differences). The welcome integration of the two fields requires the construction of mechanistic models of cognition and cognitive development that explain key phenomena in individual differences research. In this paper we argue that network modeling is a promising approach to integrate the processes of cognitive development and (developing) intelligence into one unified theory. Network models are defined mathematically, describe mechanisms on the level of the individual, and are able to explain positive correlations among intelligence subtest scores - the empirical basis for the well-known g-factor - as well as more complex factorial structures. Links between network modeling, factor modeling and item response theory allow for a common metric, encompassing both discrete and continuous characteristics, for cognitive development and intelligence.

A low-cost data logging platform is presented for environmental monitoring projects that provides long-term operation in remote or submerged environments. Three premade “breakout boards” from the open-source Arduino ecosystem are assembled into the core of the platform. The components are selected based on low-cost and ready availability, making the loggers easy to build and modify without specialized tools, or a significant background in electronics. Power optimization techniques are explained. The platform has proven to be highly reliable, and capable of operating for more than a year on standard AA batteries. The flexibility of the system is illustrated with two ongoing field studies recording drip rates in a cave, and water flow in a flooded cave system.

Considering characteristics of high river density, special underlying surface in plain river network region, and municipal drainage system function, river network drainage unit model is proposed, which is defined as a region surrounded by main river or embankment. Flood storage variety and control projects regulation of small rivers in each unit is simulated. With drainage catchment as an object, according to its drainage capacity, simplified municipal drainage model was developed. Coupling river network drainage unit model, simplified municipal drainage model and 2D flood routing model, urban flood analysis model for plain tidal river network region was developed, which could be applied to analyzing flood from upstream river, storm surge and local rainfall. Demonstration research was carried out in Puxi flood protected area in Shanghai.

Modern energy systems collect high volumes of data that can provide valuable information about energy consumption. Electric companies can now use historical data to make informed decisions on energy production by forecasting the expected demand. Many deep learning models have been proposed to deal with these type of time series forecasting problems. Deep neural networks, such as recurrent or convolutional, can automatically capture complex patterns in time series data and provide accurate predictions. In particular, Temporal Convolutional Networks (TCN) are a specialised architecture that has advantages over recurrent networks for forecasting tasks. TCNs are able to extract long-term patterns using dilated causal convolutions and residual blocks, and can also be more efficient in terms of computation time. In this work, we propose a TCN-based deep learning model to improve the predictive performance in energy demand forecasting. Two energy-related time series with data from Spain have been studied: the national electric demand, and the power demand at charging stations for electric vehicles. An extensive experimental study has been conducted, involving more than 1900 models with different architectures and parametrisations. The TCN proposal outperforms the forecasting accuracy of Long Short-Term Memory (LSTM) recurrent networks, which are considered the state-of-the-art in the field.

Recent state-of-the-art scene text recognition methods have primarily focused on horizontal text in images. However, in several Asian countries, including China, large amounts of text in signs, books, and TV commercials are vertically directed. Because the horizontal and vertical texts exhibit different characteristics, developing an algorithm that can simultaneously recognize both types of text in real environments is necessary. To address this problem, we adopted the direction encoding mask (DEM) and selective attention network (SAN) methods based on supervised learning. DEM contains directional information to compensate in cases that lack text direction; therefore, our network is trained using this information to handle the vertical text. The SAN method is designed to work individually for both types of text. To train the network to recognize both types of text and to evaluate the effectiveness of the designed model, we prepared a new synthetic vertical text dataset and collected an actual vertical text dataset (VTD142) from the Web. Using these datasets, we proved that our proposed model can accurately recognize both vertical and horizontal text and can achieve state-of-the-art results in experiments using benchmark datasets, including the street view test (SVT), IIIT-5k, and ICDAR. Although our model is relatively simple as compared to its predecessors, it maintains the accuracy and is trained in an end-to-end manner.

In this paper, an in-wheel vibration absorber for In-wheel-motor electric vehicle (IWM EV) is designed, and a comprehensive control strategy of in-wheel absorber and vehicle suspension is proposed to improve vehicle ride comfort. The proposed in-wheel vibration absorber, designed for suppressing the motor vibration, is composed of a spring and a controllable damper. The values of in-wheel spring stiffness and damper initial coefficient are determined by using the improved particle swarm optimization (IPSO) algorithm, which is carried on the typical driving condition. To deal with the negative interaction effects between vehicle suspension and in-wheel absorber, the linear quadratic regulator (LQR) algorithm is utilized to control suspension damper, and the fuzzy PID method is utilized to control in-wheel damper. Based on the four evaluation indexes including vehicle body vertical acceleration, suspension dynamic deflection, wheel dynamic load and motor wallop, the simulation results show that, the proposed LQR control of suspension effectively improves vehicle ride comfort, and the fuzzy PID control of in-wheel damper exhibits superior performance of motor vibration suppressing in comparison to conventional electric wheel.

Precision agriculture is a farm management technology that involves sensing and then responding to the observed variability in the field. Remote sensing is one of the tools of precision agriculture. The emergence of small unmanned aerial vehicles (sUAV) have paved the way to accessible remote sensing tools for farmers. This paper describes the comparison of two popular off-the-shelf sUAVs: 3DR Iris and DJI Phantom 2. Both units are equipped with a camera gimbal attached with a GoPro camera. The comparison of the two sUAV involves a hovering test and a rectilinear motion test. In the hovering test, the sUAV was allowed to hover over a known object and images were taken every second for two minutes. The position of the object in the images was measured and this was used to assess the stability of the sUAV while hovering. In the rectilinear test, the sUAV was allowed to follow a straight path and images of a lined track were acquired. The lines on the images were then measured on how accurate the sUAV followed the path. Results showed that both sUAV performed well in both the hovering test and the rectilinear motion test. This demonstrates that both sUAVs can be used for agricultural monitoring.

A reinforcement learning algorithm is proposed to improve the accuracy of short-term load forecasting (STLF) in this article. The proposed model integrates radial basis function neural network (RBFNN), support vector regression (SVR), and adaptive annealing learning algorithm (AALA). In the proposed methodology, firstly, the initial structure of RBFNN is determined by using SVR. Then, an AALA with time-varying learning rates is used to optimize the initial parameters of SVR-RBFNN (AALA-SVR-RBFNN). In order to overcome the stagnation for searching optimal RBFNN, a particle swarm optimization (PSO) is applied to simultaneously find promising learning rates in AALA. Finally, the short-term load demands are predicted by using the optimal RBFNN. The performance of the proposed methodology is verified on the actual load dataset from Taiwan Power Company (TPC). Simulation results reveal that the proposed AALA-SVR-RBFNN can achieve a better load forecasting precision as compared to various RBFNNs.

This study sought to investigate steel frames’ performance with dual lateral loader system (Frame bending + bracings of divergent and convergent) in near and far filed to fault. In order to this, four categories of steel frame with dual system with 8, 10 and 12 story are designed with average formation based on existing seismic regulation in 2800 standard of Iran and tenth chapter of national regulations of construction (planning and performing steel construction). Time history non-linear dynamic analysis under the effect of near and far field earthquakes has been done on plan’s models. Then the maximum of floors’ dislocation, floors’ drift, roof dislocation, base shear and energy curves of frames are shown and compared with each other. All non-linear time history analyses have been accomplished using PERFORM 3D software.

The practice of collecting, treating and management of solid waste prior to disposal has become a necessity in developing and modern societies. Over the years, it is known that most wastes that are disposed have a second hand value. However, the construction cost for conventional Material Recovery Facility(s) (MRFs) has been a major barrier for implementation. These technologies require considerable technical expertise, which is often not available in developing nations to successfully operate the MRFs. Covenant University; a private mission institution through her waste to wealth scheme is focused on managing and processing used materials to reusable products. These include Pet bottles, Paper wastes, Food wastes from cafeteria, plastic food packs, nylon, tin cans and others. Specific areas chosen for the Survey include the residential areas for staff and students and the two cafeterias. The waste generated was characterized based on the waste stream so as to quantify the amount of recyclable waste generated and most occurring. The survey involved the use of structured questionnaires, on-site observations and measurements. The study reveals an average amount of recyclable waste generated per day in the institution as 13.46% pet bottles, 4.03% paper, 55.56% food waste, 12.64% plastic, 9.63% nylon and 4.68% tin cans. The study established that adequate waste characterization is a requirement for effective integrated solid waste management which would boost resource recovery, reuse and recycling.

M-polynomial of different molecular structures helps to calculate many topological indices. A topological index of graph G is a numerical parameter related to G which characterizes its molecular topology and is usually graph invariant. In the field of quantitative structure-activity (QSAR) quantitative structure-activity structure-property (QSPR) research, theoretical properties of the chemical compounds and their molecular topological indices such as the Zagreb indices, Randic index, Symmetric division index, Harmonic index, Inverse sum index, Augmented Zagreb index, multiple Zagreb indices etc. are correlated. In this report, we compute closed forms of M-polynomial, first Zagreb polynomial and second Zagreb polynomial of Octagonal network. From the M-polynomial we recover some degree-based topological indices for Octagonal network. Moreover, we give a graphical representation of our results.

Microaggressions are subtle verbal and non-verbal slights based on group membership, and they are ubiquitous in the lives of racial minorities, women, and LGBTQ individuals (Sue, 2010). The goal of the current paper is to introduce a role-playing based exercise on effective responses to microaggressions. The workshop draws on the prejudice responding workshops of Plous (2000) and Lawson, et al. (2010) but integrates research-based strategies. The activity was tested in two groups of undergraduate students, and the findings suggested that both groups felt more prepared to deal with microaggressions after participating.

Data generation using high throughput technologies has led to the accumulation of diverse types of molecular data.These data have different types (discrete,real,string etc.) and occur in various formats and sizes. Datasets including gene expression, miRNA expression, protein-DNA binding data (ChIP-Seq/ChIP-ChIP), mutation data(copy number variation, single nucleotide polymorphisms), GO annotations, protein-protein interaction and disease-gene association data are some of the commonly used genomic datasets to study biological processes. Each of them provides a unique, complementary and partly independent view of the genome and hence embed essential information about their regulatory mechanisms. In order to understand the functions of genes, proteins and analyze mechanisms arising out of their interactions, information provided by each of these datasets individually may not be sufficient. Therefore integrating these multi-omic data and inferring regulatory interactions from the integrated dataset provides a system level biological insights in predicting gene functions and their phenotypic outcomes. To study genome functionality through interaction networks, different methods have been proposed for collective mining of information from an integrated dataset. We survey here data integration approaches using state-of-the-art techniques such as network integration, Bayesian networks, regularized regression (LASSO) and multiple kernel learning methods.

In this paper, we propose a novel network representation learning model TransPath to encode heterogeneous information networks (HINs). Traditional network representation learning models aim to learn the embeddings of a homogeneous network. TransPath is able to capture the rich semantic and structure information of a HIN via meta-paths. We take advantage of the concept of translation mechanism in knowledge graph which regards a meta-path, instead of an edge, as a translating operation from the first node to the last node. Moreover, we propose a user-guided meta-path sampling strategy which takes users' preference as a guidance, which could explore the semantics of a path more precisely, and meanwhile improve model efficiency via the avoidance of other noisy and meaningless meta-paths. We evaluate our model on two large-scale real-world datasets DBLP and YELP, and two benchmark tasks similarity search and node classification. We observe that TransPath outperforms other state-of-the-art baselines consistently and significantly.

Why are pieces of spaghetti generally broken into three to ten segments instead of two as one thinks? How can one obtain the desired number of fracture segments? For these problems, in this paper a strand of spaghetti is considered an elastic rod, and the finite-element software ABAQUS is used to simulate the detailed fracture dynamics of the elastic rod. By changing the size (length and diameter) of the rod, the relevant data on the fracture limit curvature and the number of fractured segments of the elastic rod are obtained. The ABAQUS simulation results confirm the scientific judgment of B. Audoly and S. Neukirch (Fragmentation of rods by cascading cracks: Why spaghetti does not break in half. Phys Rev Lett 95: 095505). Using dimensional analysis to fit the finite-element data, two relations of the elastic rod fracture dynamics are obtained: (1) the relationship between the fracture limit curvature and the diameter, and (2) the relationship between the number of fracture segments and the diameter-length ratio. Results reveal that when the length is constant, the larger the diameter (the smaller the diameter-length ratio D/L), the smaller the limit curvature; and the larger the diameter-length ratio D/L, the fewer the number of fractured segments. The relevant formulations can be used to obtain the desired number of broken segments of spaghetti by changing the diameter-to-length ratio.

Timely detection of surface damages on wind turbine blades is imperative for minimising downtime and avoiding possible catastrophic structural failures. With recent advances in drone technology, a large number of high-resolution images of wind turbines are routinely acquired and subsequently analysed by experts to identify imminent damages. Automated analysis of these inspection images with the help of machine learning algorithms can reduce the inspection cost, thereby reducing the overall maintenance cost arising from the manual labour involved. In this work, we develop a deep learning based automated damage suggestion system for subsequent analysis of drone inspection images. Experimental results demonstrate that the proposed approach could achieve almost human level precision in terms of suggested damage location and types on wind turbine blades. We further demonstrate that for relatively small training sets advanced data augmentation during deep learning training can better generalise the trained model providing a significant gain in precision.

COVID-19 has affected 212 countries around the world, killing nearly 300,000 and infecting more than 4.4 million by May 14, 2020. Bangladesh, a South Asian low-middle-income economy, has experienced a demographic and epidemiological transition with rapid urbanization and a gradual increase in life expectancy. It is the seventh most populous country in the world and population of the country is expected to be nearly double by 2050. The increasing burden of communicable diseases in Bangladesh can be attributable to rapid urbanization and nearly 50% of all slum dwellers of the country live in Dhaka division. In 2017, National Rapid Response Team of IEDCR investigated 26 incidents of disease outbreak. The joint survey of the Power and Participation Research Centre and BRAC Institute of Governance and Development reveals that per capita daily income of urban slum and rural poor drops by 80% due to present countrywide shutdown enforced by the government to halt the spread of Covid-19. 40%-50% of these population took loans to meet the daily expenses. However, the country has just 127,000 hospital beds, 91,000 of them in government-run hospitals. Researchers say, the country’s economy is economy is losing BDT 33 billion every day from its service and agriculture sectors during the nationwide shutdown.

HER2/neu positive breast tumors predict a high mortality and comprise 25-30% of breast cancer. We have shown that Flavokawain A (FKA) preferentially reduces the viabilities of HER2 overexpressing breast cancer cell lines (i.e. SKBR3 and MCF7/HER2) versus those with less HER2 expression (i.e. MCF7 and MDA-MB-468). FKA at cytotoxic concentrations to breast cancer cell lines also has minimal effect on the growth of non-malignant breast epithelial MCF10 cells. FKA induces G2M arrest in cell cycle progression of HER2 overexpressing breast cancer cell lines through inhibition of Cdc2 and Cdc25C phosphorylation and down-regulation of Myt1 and Wee1expression leading to increased Cdc2 kinase activities. In addition, FKA induces apoptosis in SKBR3 cells by increasing the protein expression of Bim and BAX and decreasing expression of Bcl₂, Bcl_x/L , XIAP and survivin. FKA also down-regulates the protein expression of HER-2 and inhibits AKT phosphorylation. Herceptin plus FKA treatment leads to enhanced growth inhibitory effect on HER-2 overexpressing breast cancer cell lines through down-regulation of Myt1, Wee1, Skp2, Survivin and XIAP. Our results suggest the promise of FKA as a novel apoptosis inducer and G2 checkpoint abrogating agent in combination with Herceptin for treatment of HER2 overexpressing breast cancer.

An application of deep convolutional neural network and recurrence plot for financial market movement prediction is presented. Though it is challenging and subjective to interpret its information, the pattern formed by a recurrence plot provide a useful insight into the dy- namical system. We used a recurrence plot of seven financial time series to train a deep neural network for financial market movement predic- tion. Our approach is tested on our dataset and achieved an average of 53.25% classification accuracy. The result suggests that a well trained deep convolutional neural network can learn a recurrence plot and pre- dict a financial market direction.

This paper presents a review of cloud application architectures and its evolution. It reports observations being made during the course of a research project that tackled the problem to transfer cloud applications between different cloud infrastructures. As a side effect we learned a lot about commonalities and differences from plenty of different cloud applications which might be of value for cloud software engineers and architects. Throughout the course of the research project we analyzed industrial cloud standards, performed systematic mapping studies of cloud-native application related research papers, performed action research activities in cloud engineering projects, modeled a cloud application reference model, and performed software and domain specific language engineering activities. Two major (and sometimes overlooked) trends can be identified. First, cloud computing and its related application architecture evolution can be seen as a steady process to optimize resource utilization in cloud computing. Second, this resource utilization improvements resulted over time in an architectural evolution how cloud applications are being build and deployed. A shift from monolithic servce-oriented architectures (SOA), via independently deployable microservices towards so called serverless architectures is observable. Especially serverless architectures are more decentralized and distributed, and make more intentional use of independently provided services. In other words, a decentralizing trend in cloud application architectures is observable that emphasizes decentralized architectures known from former peer-to-peer based approaches. That is astonishing because with the rise of cloud computing (and its centralized service provisioning concept) the research interest in peer-to-peer based approaches (and its decentralizing philosophy) decreased. But this seems to change. Cloud computing could head into future of more decentralized and more meshed services.

The stromal vascular cell fraction (SVF) of visceral and subcutaneous adipose tissue (VAT and SAT) has increasingly come into focus in stem cell research, since these compartments represent a rich source of multipotent adipose-derived stem cells (ASCs). ASCs exhibit a self- renewal potential and differentiation capacity. Our aim was to study the different expression of embryonic stem cell markers NANOG, SOX2 and OCT3/4 and to evaluate if there exists a hierarchal role in this network in ASCs derived from both SAT and VAT. ASCs were isolated from SAT and VAT biopsies of 72 consenting patients (23 men, 47 women; age 45 ± 10; BMI between 25 and 30 range) undergoing elective open-abdominal surgery. Sphere-forming capability was evaluated by plating cells in low adhesion plastic. Stem cell markers CD90 and CD105 were analyzed by flow cytometry and stem cell transcription factors NANOG, SOX2 and OCT3/4 were detected by immunoblotting and Real-Time PCR. NANOG, SOX2 and OCT3/4 interplay was explored by gene silencing. ASCs from VAT and SAT confirmed their mesenchymal stem cell (MSC) phenotype expressing the specific MSC markers CD90, CD105, NANOG, SOX2 and OCT3/4. NANOG silencing induced a significant OCT 3/4 (70% ± 0.05) and SOX2 (75% ± 0.03) down-regulation whereas SOX2 silencing did not affect NANOG gene expression. Adipose tissue is an important source of MSC, and siRNA experiments endorse a hierarchical role of NANOG in the complex transcription network that regulates pluripotency and plasticity.

In 1990 the Malaysian Government launched Vision 2020 with the goal of Malaysia becoming a ‘fully developed country’ by the year 2020. In this drive for development the country has been examining many of its key natural assets, exploring how to both preserve them whilst ensuring that they make the maximum possible contribution to national development goals. Endau Rompin is one of these assets, being the second largest National Park in Peninsula Malaysia. The rich tropical rainforest flora and fauna of the Park and its hinterland, however, are threatened by various anthropogenic forces, most notably deforestation and poaching; both of which have taken the Park’s flagship species - the Tiger Panthera tigris jacksoni – towards the brink of local extinction. Malaysia’s statutory East Coast Economic Region Development Council commissioned a study to consider ways of increasing tourism revenues from the Park while at the same time reversing these threats. The key conclusion drawn is that a more holistic, landscape-scale approach should be adopted, with Endau Rompin forming part of a wider strategic economic zone based around sustainable tourism and land management. The proposed expanded zone extends eastwards beyond the confines of the Park, across the coastal plain to the South China Sea, and onwards to the neighbouring Mersing Islands. This expanded zone is referred to as Malaysia’s new ‘Rainforest to Reef Region’.

Cloud computing refers to applications delivered as services over the Internet. Cloud systems employ policies that are inherently dynamic in nature and that depend on temporal conditions defined in terms of external events, such as the measurement of bandwidth, use of hosts, intrusion detection or specific time events. In this paper, we investigate an optimized resource management scheme named v-Mapper. The basic premise of v-Mapper is to exploit application-awareness concepts using software-defined networking (SDN) features. This paper makes three key contributions to the field: (1) We propose a virtual machine (VM) placement scheme that can effectively mitigate the VM placement issues for data-intensive applications; (2) We propose a validation scheme that will ensure that a service is entertained only if there are sufficient resources available for its execution and (3) We present a scheduling policy that aims to eliminate network load constraints. An evaluation was carried out with various benchmarks and demonstrated that v-Mapper shows improved performance over other state-of-the-art approaches in terms of average task completion time, service delay time and bandwidth utilization. Given the growing importance of supporting large-scale data processing and analysis in datacentres, the v-Mapper system has the potential to make a positive impact in improving datacentre performance in the future.

Layout estimation is a challenge of segmenting a cluttered room image into floor, walls and ceiling. We applied Double refinement network proved to be efficient in the depth estimation to generate heat maps for room key points and edges. Our method is the first not using encoder-decoder architecture for the room layout estimation. ResNet50 was utilized as a backbone for the network instead of VGG16 commonly used for the task, allowing the network to be more compact and faster. We designed a special layout score function and layout ranking algorithm for key points and edges output. Our method achieved the lowest pixel and corner errors on the LSUN data set. The input image resolution is 224*224.

Sentinel-2 can provide multi-spectral optical remote sensing images in RGBN bands with a spatial resolution of 10m, but the spatial details provided are not enough for many applications. WorldView can provide HR multi-spectral images less than 2m, but it is a commercial paid resource with relatively high usage costs. In this paper, without any available reference images, Sentinel-2 images at 10m resolution are improved to a resolution of 2.5m through super-resolution (SR) based on deep learning technology. Our model, named DKN-SR-GAN, uses degradation kernel estimation and noise injection to construct a dataset of near-natural low-high-resolution (LHR) image pairs, with only low-resolution (LR) images and no high-resolution (HR) prior information. DKN-SR-GAN uses the Generative Adversarial Networks (GAN) combined of ESRGAN-type generator, PatchGAN-type discriminator and the VGG-19-type feature extractor, using perceptual loss to optimize the network, so as to obtain SR images with clearer details and better perceptual effects. Experiments demonstrate that in the quantitative comparison of the non-reference image quality assessment (NR-IQA) metrics like NIQE, BRISQUE and PIQE, as well as the intuitive visual effects of the generated images, compared with state-of-the-art models such as EDSR8-RGB, RCAN and RS-ESRGAN, our proposed model has obvious advantages.

We consider the financial planning problem of a retiree wishing to enter a retirement village at a future uncertain date. The date of entry is determined by the retiree's utility and bequest maximisation problem within the context of uncertain future health states. In addition, the retiree must choose optimal consumption, investment, bequest and purchase of insurance products prior to her full annuitisation on entry to the retirement village. A hyperbolic absolute risk-aversion (HARA) utility function is used to allow necessary consumption for basic living and medical costs. The retirement village will typically require an initial deposit upon entry. This threshold wealth requirement leads to exercising the replication of an American put option at the uncertain stopping time. From our numerical results, active insurance and annuity markets are shown to be a critical aspect in retirement planning.

Great Malang region is developing rapidly with the population increase and inhabitant`s activity, like migration and urbanization. Other activities like agricultural expansion as well as an uncontrolled residential development need to be monitored to avoid any negative impact in the future. The availability of free and open-source software, spatial high-resolution satellite imagery datasets, and powerful algorithms open the possibilities to map, monitor, and predict the future trend of land use land cover (LULC) changes. However, the accuracy and precision of this model is still in doubt, especially in the Great Malang region. Research is needed to provide a foundational basis and documentation on how the changes occur, where did the changes occur, and the accuracy of the predicted model. This study tries to answer those questions using the high spatial resolution of Sentinel-2 imageries. Combination of the fuzzy algorithm, artificial neural network, and cellular automata was utilized to process the datasets. We analysed four different scenarios of simulation and the result then compared. The different number of hidden layers and iteration was used and evaluated to understand the effect of different parameters in the prediction result. The best scenario was then used to predict future land use changes. This study has successfully produced the future LULC model of Great Malang region with high accuracy level (87%). The study also found that the land use transformation from agriculture to urban built-up area is relatively low, where changes of the built-up area over three periods of analysis are below than 5%. This is due to the physical condition of Great Malang region where mountainous areas are dominated.

Geospatial Information Systems (GIS) can provide a great environment for using machine learning algorithm for spatial data such as satellite images. Integrating this functionality with artificial intelligence algorithms for analyzing spatial data enables us to predict challenging disasters such as deforestation. Deforestation as an environmental problems has been recorded the most serious threat to environmental diversity and one of the main components of land-use change. In this paper, we investigate spatial distribution of deforestation using artificial neural networks and satellite imagery. We modeled deforestation process using various factors in determining the relationship between deforestation and environmental and socioeconomic factors. Hence, for this purpose, the proximity to roads and habitats, fragmentation of the forest, height from sea level, slope, and soil type are considered in the model. In this research, we modeled land cover changes (forests) to predict deforestation using an artificial neural network due to its significant potential for the development of nonlinear complex models. The procedure involves image registration and error correction, image classification, preparing deforestation maps, determining layers, and designing a multi-layer neural network to predict deforestation. The satellite images for this study are of a region in Hong Kong which are captured from 2012 to 2016. The results of the study demonstrate that neural networks approach for predicting deforestation can be utilized and its outcomes show the areas that destroyed during the research period.

The problem of quantifying the vulnerability of graphs has received much attention nowadays, especially in the field of computer or communication networks. In a communication network, the vulnerability measures the resistance of the network to disruption of operation after the failure of certain stations or communication links. If we think of a graph as modeling a network, the average lower 2-domination number of a graph is a measure of the graph vulnerability and it is defined by ${\gamma }_{2av}\left(G\right)=\frac{1}{\left|V\left(G\right)\right|}{\sum }_{v\in V\left(G\right)}{\gamma }_{2v}\left(G\right)$, where the lower 2-domination number, denoted by ${\gamma }_{2v}\left(G\right)$, of the graph G relative to v is the minimum cardinality of 2-domination set in G that contains the vertex v. In this paper, the average lower 2-domination number of wheels and some related networks namely gear graph, friendship graph, helm graph and sun flower graph are calculated. Then, we offer an algorithm for computing the 2-domination number and the average lower 2-domination number of any graph G.

A tailored model for the assessment of environmental benefits achievable by “light-weighting” in the automotive field is presented. The model is based on the Fuel Reduction Value (FRV) coefficient, which expresses the Fuel Consumption (FC) saving involved by a 100 kg mass reduction. The work is composed of two main sections: simulation and environmental modelling. Simulation modelling performs an in-depth calculation of weight-induced FC whose outcome is the FRV evaluated for a wide range of Diesel Turbocharged (DT) vehicle case studies. Environmental modelling converts fuel saving to impact reduction basing on the FRVs obtained by simulations. Results show that for the considered case studies, FRV is within the range 0.115–0.143 and 0.142–0.388 L/100 km × 100 kg, respectively, for mass reduction only and powertrain adaptation (secondary effects). The implementation of FRVs within the environmental modelling represents the added value of the research and makes the model a valuable tool for application to real case studies of automotive lightweight LCA.

This paper introduces a fusion convolutional architecture for efficient learning of spatio-temporal features in video action recognition. Unlike 2D CNNs, 3D CNNs can be applied directly on consecutive frames to extract spatio-temporal features. The aim of this work is to fuse the convolution layers from 2D and 3D CNNs to allow temporal encoding with fewer parameters than 3D CNNs. We adopt transfer learning from pre-trained 2D CNNs for spatial extraction, followed by temporal encoding, before connecting to 3D convolution layers at the top of the architecture. We construct our fusion architecture, semi-CNN, based on three popular models: VGG-16, ResNets and DenseNets, and compare the performance with their corresponding 3D models. Our empirical results evaluated on the action recognition dataset UCF-101 demonstrate that our fusion of 1D, 2D and 3D convolutions outperforms its 3D model of the same depth, with fewer parameters and reduces overfitting. Our semi-CNN architecture achieved an average of 16 – 30% boost in the top-1 accuracy when evaluated on an input video of 16 frames.

Background. Upper respiratory infections (URIs) remains as significant cause of morbidity in children. Evidence on efficacy of probiotics to prevent URIs in children is increasing. This systematic review was assembled to analyze evidence about the efficacy of probiotics to reduce duration of upper respiratory infections in ambulatory children. Methods. Randomized controlled trials (RCTs) comparing probiotics vs. placebo to prevent URIs, published between 2001 and 2016 were considered. Quality evaluation was evaluated using CONSORT. Standard mean difference (SMD) or risk ratio (RR) was calculated. Network Meta-Analysis (NMA), using a random effect model was assembled. Results. 31 RCTs were evaluated and 20 studies were included with 3,635 children randomized to probiotics and 3,433 to placebo. Lactobacillus reuteri [SMD -0.56 CI95% (-0.72 to -0.41), p 0.0001] and Lactobacillus acidophillus [SMD -0.33 CI95% (-0.60 to -0.06), p 0.01] were superior to placebo to reduce duration of URIs. L. rhamnosus GG showed tendency [SMD -0.14 CI95% (-0.28 to 0.0), p 0.048]. On the network forest plot L. reuteri showed preventive equivalence when was compared to L. rhamnosus GG, L. casei and BB12. Conclusions. Lactobacillus reuteri, Lactobacillus rhamnosus GG and Bifidobacterium BB12 are evidence-based alternatives to be considered to prevent URIs in children.

Waddington’s epigenetic landscape, a famous metaphor in developmental biology, depicts how a stem cell progresses from an undifferentiated phenotype to a differentiated one. The concept of “landscape” in the context of dynamical system theory represents a high-dimensional cell state space, in which each cell phenotype is considered as an “attractor” that is determined by interactions among multiple variables (molecular players), and is buffered against environmental fluctuations. Further, biological noise is thought to play an important role during these cell-fate decisions and in fact controls transitions between different phenotypes. Here, we discuss these phenotypic transitions in cancer from a dynamical systems perspective and invoke the concept of “cancer attractors” – hidden stable states of the underlying regulatory network that are not occupied by normal cells. Using epithelial-to-mesenchymal transition (EMT), cancer stem-like properties, metabolic reprogramming and the emergence of drug/hormone resistance as examples, we illustrate how phenotypic plasticity in cancer cells enables them to acquire hybrid phenotypes (such as hybrid epithelial/mesenchymal and hybrid metabolic phenotypes) that tend to be more aggressive and notoriously resilient to drug/hormone treatment. Furthermore, we highlight multiple factors that may give rise to phenotypic plasticity in cancer cells, such as (a) multi-stability or oscillatory behaviors governed by underlying regulatory networks involved in cell-fate decisions in cancer cells, and (b) network rewiring due to conformational dynamics of intrinsically disordered proteins (IDPs) that are highly enriched in cancer cells. We conclude by discussing why a therapeutic approach that promotes ‘recanalization’, i.e. the exit from “cancer attractors” and re-entry into “normal attractors”, is more likely to succeed rather than a conventional approach that targets individual molecules/pathways.

The separation of sister chromatids during anaphase is the culmination of mitosis and one of the most strikingly beautiful examples of cellular movement. It consists of two distinct processes: Anaphase A, the movement of chromosomes toward spindle poles via shortening of the connecting fibers, and anaphase B, separation of the two poles from one another via spindle elongation. I focus here on anaphase A chromosome-to-pole movement. The chapter begins by summarizing classical observations of chromosome movements, which support the current understanding of anaphase mechanisms. Live cell fluorescence microscopy studies showed that poleward chromosome movement is associated with disassembly, or ‘melting’ of the kinetochore-attached microtubule fibers that link chromosomes to poles. Microtubule-marking techniques established that kinetochore-fiber disassembly often occurs through a ‘pac-man’ mechanism, where tubulin subunits are lost from kinetochore-attached plus ends and the kinetochore appears to consume its microtubule track as it moves poleward. In addition, kinetochore-fiber disassembly in many cells occurs partly through ‘flux’, where the microtubules flow continuously toward the poles and tubulin subunits are lost from minus ends. Molecular mechanistic models for how load-bearing attachments are maintained to disassembling microtubule ends, and how the forces are generated to drive pac-man and flux-based movements, are discussed.

This research aims to determine the similarities in groups of people to build a film recommender system for users. Users often have difficulty in finding suitable movies due to the increasing amount of movie information. The recommender system is very useful for helping customers choose a preferred movie with the existing features. In this study, the recommender system development is established by using several algorithms to obtain groupings, such as the K-Means algorithm, birch algorithm, mini-batch K-Means algorithm, mean-shift algorithm, affinity propagation algorithm, agglomerative clustering algorithm, and spectral clustering algorithm. We propose methods optimizing K so that each cluster may not significantly increase variance. We are limited to using groupings based on Genre and, Tags for movies. This research can discover better methods for evaluating clustering algorithms. To verify the quality of the recommender system, we adopted the mean square error (MSE), such as the Dunn Matrix and Cluster Validity Indices, and social network analysis (SNA), such as Degree Centrality, Closeness Centrality, and Betweenness Centrality. We also used Average Similarity, Computational Time, Association Rule with Apriori algorithm, and Clustering Performance Evaluation as evaluation measures to compare method performance of recommender systems using Silhouette Coefficient, Calinski-Harabaz Index, and Davies-Bouldin Index.

Deep learning (DL), a branch of machine learning (ML) and artificial intelligence (AI) is nowadays considered as a core technology of today's Fourth Industrial Revolution (4IR or Industry 4.0). Due to its learning capabilities from data, DL technology originated from artificial neural network (ANN), has become a hot topic in the context of computing, and is widely applied in various application areas like healthcare, visual recognition, cybersecurity, and many more. However, building an appropriate DL model is a challenging task, due to the dynamic nature and variations in real-world problems and data. Moreover, the lack of core understanding turns DL methods into black-box machines that hamper development at the standard level. This article presents a structured and comprehensive view on DL techniques including a taxonomy considering various types of real-world tasks like supervised or unsupervised. In our taxonomy, we take into account deep networks for supervised or discriminative learning, unsupervised or generative learning as well as hybrid learning and relevant others. We also summarize real-world application areas where deep learning techniques can be used. Finally, we point out ten potential aspects for future generation DL modeling with research directions. Overall, this article aims to draw a big picture on DL modeling that can be used as a reference guide for both academia and industry professionals.

Multi-stakeholder based construction projects are subject to various risk factors due to dynamic business environments. These risks affect project activities which indirectly impact construction costs, resulting in delays and poor building quality. So, managing these project risks requires suitable risk mitigation strategies to evaluate and analyse their severity. Hence, risk evaluation and assessment of construction projects is a multi-criteria decision making (MCDM) problem. In present real-life problems, evaluation of project risks is often uncertain and even incomplete, and the prevailing methodologies fail to handle such situations. To address the problem, this paper extends the analytical network process (ANP) methodology in the D number domain to handle three types of ambiguous evaluations, viz. complete, uncertain, and incomplete, and assesses the weight of risk criteria. The D number based approach overcomes the deficiencies of the exclusiveness hypothesis and completeness constraint of Dempster-Shafer (D-S) theory. Here, preference ratings of the decision matrix for each decision-maker are determined using a D number extended consistent fuzzy preference relation (D-CFPR). An extended multi-attributive border approximation area comparison (MABAC) method in D number is then developed to rank and select the best alternative risk response strategy. Finally, an illustrative example from construction sector is presented to check the feasibility of the proposed approach. For checking the reliability of alternative ranking, a comparative analysis is performed with different MCDM approaches (D-COPRAS, D-ARAS, D-MABAC, and D-TOPSIS). Based on different criteria weights, a sensitivity analysis of obtained ranking of the hybrid D-ANP-MABAC model is performed for verify the robustness of the proposed method.

The development of low-cost, open-source Remotely Operated Vehicle (ROV) systems has provided almost unrestricted access for researchers looking to monitor the marine environment in ever greater resolution. Sampling microbial communities from the marine environment, however, still usually relies on Niskin-bottle sampling (ROV or CTD based), a method which introduces an inaccuracy and variability that is incompatible with metatranscriptomic analysis. Here, we describe a versatile, easily-replicated platform which achieves in situ mRNA preservation, via the addition of RNAlater to filtered microbial cells, to enhance ROV or CTD functionality.

One of the most used markers of cancer stem cells in several cancers, including colorectal cancer and breast cancer, is CD44. CD44 is a glycoprotein that traverses the cell membrane and binds to many ligands including hyaluronan resulting in activation of signaling cascades. Several reports have shown conflicting data on the expression of CD44 and that the expression depends on modes of investigations and subtypes of cancers. In addition, the correlation between CD44 expression and drug resistance, immune infiltration, EMT, metastasis and patients prognosis in several cancer types remains unclear. This study investigated CD44 expression in several cancers and explored its relationship with tumorigenesis using various publicly available databases, including The Cancer Genome Atlas, GEPIA, Oncomine, Genomics of Drug Sensitivity in Cancer and Tumor Immune Estimation Resource. Our analysis reveals that CD44 is differentially expressed in different cancers. CD44 expression is significantly associated with cancer patients’ survival in gastric, pancreatic and colorectal cancers. In addition, CD44 expression is closely linked with immune infiltration and immune suppressive features in pancreatic, colon adenocarcinoma and stomach cancer. High CD44 expression was significantly correlated with the expression of drug resistance-, EMT- and metastasis- linked genes. Tumors expressing high CD44 have higher mutation burden and afflict older patients than tumors expressing low CD44. Cell lines expressing high CD44 are more resistant to anti-cancer drugs compared to those expressing low CD44. Protein-protein interaction investigations and functional enrichment analysis showed that CD44 interacts with gene products related to cell-substrate adhesion, migration, platelet activation, and cellular response to stress. KEGG pathway analysis revealed that these genes play key roles in biological adhesion, cell component organization, locomotion, G-α-signaling and the response to stimulus. Overall, this investigation reveals that CD44 play significant roles in tumorigenesis, can be used as a prognostic biomarker in several cancers and can be therapeutically targeted in cancer therapy.