Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

Pre-existing fracture and secondary cracks in rock mass are formed by natural power, such as magma condensed to igneous rocks and tectonic movement. The orientation and inclination of these fractures obey certain laws relating to the stress, temperature, minerals, water and so on. Therefore, cracks react differently under the same external loading on the condition of various inclination, fissure apertures, stiffness and joint roughness. To simulate the crack propagation, experiments on hollow cylinder cut by one oblique interface mimicking single fracture accumulated numerous data discovering the failure criterion in accordance with the Mohr-Coulomb criterion. And theory on the Terzaghi’s effective principle take an essential role in controlling the behavior of triggering fault. This paper introduced a series of oblique plane cutting the cylinder regarded as fractures at different inclination to concentrate on how the fracture characteristics effect the stress and strain distribution inside the specimen, especially, the relationship between displacement and water head. The key point of this numerical simulation is coupling the solid phase and the fluid phase, specifically, the mechanic and seepage field. According to the statics, curves referring to deformation and water head could be described as increasing lines. Besides, simulation on coupling solid phase and fluid phase can supply crucial evaluation on activating existing fault, and thus predicting induced seismicity in reservoirs or estimating damage in shale gas exploration.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

The diagnosis of a rolling bearing for monitoring its status is critical for maintaining industrial equipment using rolling bearings. The traditional method of diagnosing faults of the rolling bearing has low identification accuracy, which needs artificial feature extraction to enhance the accuracy. 1D-CNN method not only can diagnose bearing faults accurately but also overcome shortcomings of the traditional methods. Different from machine learning and other deep learning models, the 1D-CNN method does not need pre-processing one-dimensional data of rolling bearing’s vibration. Thus, it enhances the processing speed and improves the network structure to have a reasonable design for small sample data sets. This study proposes and tests a 1D-CNN method for diagnosing rolling bearings. By introducing the dropout operation, the method obtains high accuracy and improves the generalizing ability. The experimental results show 99.52% of the average accuracy under a single load and 98.26% under different loads.

Near-fault ground motions can cause severe damage to civil structures, including bridges. Safety assessment of these structures for near fault ground motion is usually performed through Non-Linear Dynamic Analyses, while faster methods are often used. IMPAb (Incremental Modal Pushover Analysis for Bridges) permits to investigate the seismic response of a bridge by considering the effects of higher modes, which are often relevant for bridges. In this work, IMPAb is applied to a bridge case study considering near-fault pulse-like ground motion records. The records were analyzed and selected from the European Strong Motion Database and the pulse parameters were evaluated. In the paper results from standard pushover procedures and IMPAb are compared with nonlinear Response-History Analysis (NRHA), considering also the vertical component of the motion, as benchmark solutions and incremental dynamic analysis (IDA). Results from the case study demonstrate that the vertical seismic action has a minor influence on the structural response of the bridge. Therefore IMPAb, which can be applied considering vertical motion, remains very effective conserving the original formulation of the procedure, and can be considered a well performing procedure also for near-fault events.

A Mw7.8 earthquake struck Turkey on February 6, 2023, causing severe casualties and economic losses. This paper investigates the characteristics of strong ground motion and seismogenic fault of the earthquake. We collected and processed the strong ground motion records of 379 stations using Matlab, SeismoSignal and Surfer software, and obtained the peak ground acceleration (PGA) contour map. We analyzed the near-fault effect, the fault locking segment effect and the trampoline effect of the earthquake based on the spatial distribution of PGA, the fault geometry and slip distribution. We found that the earthquake generated a very strong ground motion concentration effect in the near-fault area, with the maximum PGA exceeding 2000cm/s2. However, the presence of fault locking segments influenced the spatial distribution of ground motion, resulting in four significant PGA high-value concentration areas at a local dislocation, a turning point and the end of the East Anatolian Fault. We also revealed for the first time the typical manifestation of the trampoline effect in this earthquake, which was characterized by a large vertical acceleration with the positive direction significantly larger than the negative direction. This paper provides an important reference for understanding the seismogenic mechanism, damage mode, characteristics and strong earthquake law of Turkey earthquake.

A review of influence of drag-reducing agents on curved pipe flows is presented in this work. In addition, this review outlined proposed mechanism, friction factor and fluid flux models for drag-reducing agents in curved pipe flows. Our finding reveals that drag reduction by additives in curved pipes is quite significant but generally lower than the corresponding drag reduction in straight pipes. It decreases with increase in curvature ratio and more pronounced in the transition and turbulent flow regimes. Drag reduction strongly depends on the polymers and surfactants’ concentrations as well as the bubble fraction of micro-bubbles. It is also reported that drag reduction in curved pipes depends on temperature and existence of dissolved salts in the fluids. Maximum drag reduction asymptote differed between straight and curved pipes and between polymer and surfactant. No definite conclusion could be drawn as regards drag reduction for two-phase flow in curved pipes due to the limited studies in this area. Many questions such as the mechanism of drag reduction in curved pipes and how drag-reducing agents interact with secondary flows still remained unanswered. Hence, some research gaps have been identified with recommendations for areas of future researches.

The past two decades has seen a growing demand for high-power, high-voltage utility scale inverters mostly fueled by the integration of large solar PV and wind farms. Multilevel inverters have emerged as the industry choice for these megawatt range inverters because their reduced voltage stress, capable of generating an almost sinusoidal voltage, in-built redundancy, among others. This paper present a new Switched-Source Multilevel Inverter (SS MLI) architecture. The new inverter show superior over existing topologies. It has reduced voltage stress on the semiconductor, uses less number of switches –reduced size/weight/cost and increased efficiency. The new SSMLI is comprised of two voltage sources (V₁, V₂) and 6 switches. It is capable of generating 5-level output voltage in symmetric modes (i.e., V₁ = V₂), and 7-level output voltage in asymmetric modes (i.e., V₁ ≠ V₂). To demonstrate the validity of the proposed inverter, simulations results using MATLAB^® /Simulink^® for 5- and 7-level output voltages are presented . The simulations are also verified experimentally using a laboratory prototype.

This paper proposes how to reduce the consumption of active electrical energy (kwh) by 90.3% while maintaining the same mechanical work speed (RPM) at variable torque loads (fans or air-fluid blowers, centrifugal pumps are not included). of water and similar fluids), by using the “Fan Law” in an innovative way in PMSM-type synchronous motors (a comparative study never before carried out on the Fan Law). The work is carried out comparatively between brushless a-synchronous motors with starting loop (or motor with a short-circuited loop) versus brushed a-synchronous motors and PMSM-type synchronous motors without the need to use VDF (variable frequency drives), simplifying technology (electronics) and saving costs in an innovative way (R+D+i). The case study was developed on a design applied to a centrifugal air extractor/blower with PMSM/IPM type synchronous motor. Applying one of the fan affinity laws –with the impeller diameter 10.5 (mm) constant- the electrical power absorbed by the blower motor is proportional to the cube of the shaft speed: . Being “P” power (Watts) and “N” speed (RPM). Carrying out a comparative study between power (watts), active energy consumption (kwh) and rotational speed (RPM). This has a direct impact on the costs of residential and commercial single-phase active electrical energy consumption, measured in kilowatt-hours (kwh). Carrying out a comparative study between three (3) types of alternating current (AC) electrical machines, according to the NEMA (National Electrical Manufacturers Association); AC motors fall into three (3) categories. One (1), synchronous motors (Syncrhonous Motor) of three types: (1a) excitation by DC (DC Excited Motor), (1b) permanent magnet (Permanent Magnet Motor) and (1c) reluctance motor (Reluctance Motor) or motor Step by Step. Two (2), asynchronous induction motors of two types: (2a) Squirrel-Cage Induction Motor and (2b) Wound-Rotor Induction Motor. Three (3) series-wound motor (Series-Wound Motor) also called universal motor (they have carbons).

This study sought to investigate steel frames’ performance with dual lateral loader system (Frame bending + bracings of divergent and convergent) in near and far filed to fault. In order to this, four categories of steel frame with dual system with 8, 10 and 12 story are designed with average formation based on existing seismic regulation in 2800 standard of Iran and tenth chapter of national regulations of construction (planning and performing steel construction). Time history non-linear dynamic analysis under the effect of near and far field earthquakes has been done on plan’s models. Then the maximum of floors’ dislocation, floors’ drift, roof dislocation, base shear and energy curves of frames are shown and compared with each other. All non-linear time history analyses have been accomplished using PERFORM 3D software.

In this paper, a new approach to the sliding-mode control of single-phase inverters under linear and non-linear loads is introduced. The main idea behind this approach is to utilize a non-linear, flexible and multi-slope function in controller structure. This non-linear function makes the controller possible to control the inverter by a non-linear multi-slope sliding surface. In general, this sliding surface has two parts with different slopes in each part and the flexibility of the sliding surface makes the multi-slope sliding-mode controller (MSSMC) possible to reduce the total harmonic distortion, to improve the tracking accuracy, and to prevent overshoots leading to undesirable transient-states in output voltage which are occurred when the load current sharply rises. In order to improve the tracking accuracy and to reduce the steady-state error, an integral term of the multi-slope function is also added to the sliding surface. The improved performance of the proposed controller is confirmed by simulations and finally, the results of the proposed approach are compared with a conventional SMC and a SRFPI controller.

In this paper, four types of open service signals of BDS-3 satellite (B1I, B1C, B2a, and B3I) and B2I signals broadcasted by BDS-2 satellites were used in the time frequency transfer and positioning experiments with signal coexisting in BDS system, and the single frequency PPP (precise point positioning) method was used. Modified GRoup And PHase Ionospheric Correction (GRAPHIC) method was proposed and verified by the experiment. The results show that 18 selected stations can achieve decimeter-level positioning results with single frequency. Compared with the general observation method, the proposed modified GRAPHIC method improves the stability and precision of positioning and timing significantly, and the positioning accuracy of 5 frequency signals is increased 40.4%, 32.2%, 80.3%, 12.4%, and 10.3%, respectively. The frequency stability can reach the same accuracy as that of dual-frequency with BDS in the current state.

A triangular lattice model for pattern formation by core-shell particles at fluid interfaces is introduced and studied for the particle to core diameter ratio equal to 3. Repulsion for overlapping shells and attraction at larger distances due to capillary forces are assumed. Ground states and thermodynamic properties are determined analytically and by Monte Carlo simulations for soft outer- and stiffer inner shells, with different decay rates of the interparticle repulsion. We find that thermodynamic properties are qualitatively the same for slow and for fast decay of the repulsive potential, but the ordered phases are stable for temperature range depending strongly on the shape of the repulsive potential. More importantly, there are two types of patterns formed for fixed chemical potential - one for a slow and another one for a fast decay of the repulsion at small distances. In the first case two different patterns - for example clusters or stripes - occur with the same probability for some range of the chemical potential. For fixed concentration, an interface is formed between two ordered phases with the closest concentration, and the surface tension takes the same value for all stable interfaces. In the case of degeneracy, a stable interface cannot be formed for one out of four combinations of the coexisting phases, because of a larger surface tension. Our results show that by tuning the architecture of a thick polymeric shell, many different patterns can be obtained for sufficiently low temperature.

Ensuring a protection scheme in DC distribution is more difficult to achieve against pole-to-ground fault than in AC distribution system because of the absence of zero crossing points and low line impedance. To complement the major obstacle of limiting the fault current, several compositions have been proposed related to mechanical switching and solid-state switching. Among them, solid-state circuit breakers(SSCBs) are considered a possible solution to limit fast fault current. However, they may cause problems in circuit complexity, reliability and cost-related troubles due to the use of multiple power semiconductor devices and additional circuit configuration to commutate current. This paper proposes the SSCB with a coupled inductor(SSCB-CI) which has symmetrical configuration. The circuit is comprised of passive components like commutation capacitors, a CI and damping resistors. Thus, proposed SSCB-CI offers the advantages of simple circuit configuration and fewer utilized power semiconductor devices than another typical SSCBs in LVDC microgrid. For analysis, six operation states are described for the voltage across main switches and fault current. The effectiveness of the SSCB-CI against a short-circuit fault is proved via simulation and experimental results in a lab-scale prototype.

Carbon sequestration is associated with plant biomass and soils. The amount of carbon sequestration in the Atewa Range Forest Reserve (ARFR) is affected by varied anthropogenic activities like logging, mining and farming. This study estimate the above and below ground carbon stock and assess human-induced stress impacts on the Highly Stressed Vegetation (HSV), Moderately Stressed Vegetation (MSV), and Non-Stressed Vegetation (NSV) in the ARFR. The above ground biomass of trees was determined using the allometric model of (Henry, et al., 2010) whereas plants root biomass was calculated using Cairns et al. (1997). Soil organic carbon was determined using the Walkley–Black method. We observed that carbon stock was higher in the above-ground than the below-ground component. The MSV, recorded the highest stock of carbon followed by the NSV and the HSV whilst sequestrated carbon stocks was generally high and varied across the three stress levels. Within the forest, the intensity of anthropogenic activities has negatively impacted the amounts of carbon sequestrated at various levels.

Exclosures are used to regenerate native vegetation as a way to reduce soil erosion, increase rain water infiltration and provide fodder and woody biomass in degraded grazing lands. Therefore, this study assessed the impact of grazing exclosure on vegetation biomass, carbon sequestration and soil nutrients under five and ten years of grazing exclosures and freely grazed areas in Tigray, northern Ethiopia. Vegetation biomass, carbon stocks and soil nutrients increased with increasing grazing exclusion. However, open grazing lands and five years of grazing exclosure did not differ in aboveground biomass, above-and-belowground carbon stocks. Moreover, ten years of grazing exclosure had a higher (P<0.01) grass, herb and litter carbon stocks compared to five years exclosure and open grazing lands. The total carbon stock was higher for ten years exclosure (193.3 t C ha-1) than the five years exclosure (154.0 t C ha-1) and in open grazing areas (146.6 t C ha-1). Grazing lands closed for ten years had a higher SOC, organic matter, total N, available P, and exchangeable K+ and Na+ compared to five year’s exclosure and open grazing lands. Therefore, establishment of grazing exclosures had a positive effect in restoring degraded grazing lands, thus improving vegetation biomass, carbon sequestration potentials and soil nutrients under the changing climate and global warming.

It's a method to achieve energy savings in single-phase active power greater than that obtained with the "Fan Law" in electric machines applied to ventilation. Quantitative analysis methods were based on electrotechnical techniques, practiced with the corresponding laboratory equipment on the working materials (three prototypes of electric machines). The results obtained from experimentation on the test bench were recorded in tables that collect data of formulas, values, and physical units. The discussion provides a comprehensive comparative study, mainly between power (watts), active energy consumption (kWh), and rotational speed (revolutions per minute). The permanent magnet synchronous motor (PMSM) with the coupling of an RL circuit design does mechanical work at its maximum speed of 3000 (RPM) with only 6.3 (Watts), which is equivalent to 25.2% of the active power required by the single-phase induction asynchronous motor (or shaded pole motor), which required 25 (Watts) to rotate at 1690 (RPM). This translates to 75% lower active power with a 44% superiority in speed, resulting in a 75% savings in single-phase active energy (measured in kWh). The same occurs when comparing it to the universal AC motor (with brushes and wound rotor) to maintain a speed of 3000 (RPM); since it consumes 64.8 (Watts), which is 90.3% more single-phase active energy than that required to achieve the same rotational speed as the permanent magnet synchronous motor (PMSM). The study was conducted on all motors with the same impeller blade diameter and under identical air temperature and atmospheric pressure conditions.

The product is a centrifugal air extractor, whose objective is to extract the stale air of SARS-CoV-2 or Covid-19 (Coronavirus); designed for civil and commercial use, it works with a single-phase alternating current (AC) motor of 220 (V) and 50 (Hz), with high energy efficiency (EE). Developed under the Design Thinking methodology, by electromechanical simulation using NI Multisim 14.0 software, case design using Cfturbo 2020 R2.0 CAD software, and rapid 3D prototyping with the OverLord Pro printer; with a prototype of the conventional stator winding of a synchronous motor with a two-pole PMSM/IPM single-phase alternating current (AC) field winding and a 4000 (Gauss) ferromagnetic ceramic magnet rotor. Innovating online nº 15 of invention patent nº 381968 by Nikola Tesla, 5/1/1888.One of the objectives is to link the middle level or Technical Schools with the University system (and careers with a Technological profile) through Project B374 located in the Secretariat of Science and Technology (SCyT) of the National University of La Plata ( UNLP), whose title is: “Integrated Management of Design and Innovation. Contributions for a theoretical-conceptual and methodological review” by the Director: Mg. Federico del Giorgio Solfa. Just as links were sought with the Research and Development Laboratory of the Department of Industrial Design (LIDDI-FBA-UNLP) through its Director D.I. Pablo Ungaro and D.I. Ana Bocos. In 2021, the project participated in the INNOVAR National Contest of the Ministry of Science, Technology and Productive Innovation of the Nation (MINCYT), Argentine Republic; in the "Covid-19 Projects" category, having been selected in the catalog of innovative products, won the 1st. "Covid-19 Projects" position of the National Agency for Research and Technological Development and local innovation (R+D+i) dependent on MINCYT.The results showed, according to the analysis of the test bench, that the PMSM/IPM type synchronous motor used in the centrifugal fan, with the innovation of the reactance-inductive control in series plus the capacitor in parallel, reduces the power by 67% (Watts) and active energy consumption (kWh), performing 56% more mechanical work (Joules) on the fluid air (with a 50% reduction in carbon footprint). Which leads us to the following conclusion: it is possible to develop centrifugal fans that save electricity (kWh) without the need to resort to (1) the "Fan Affinity Law", nor (2) the use of variable speed drives (VDF) or frequency (which are devices with complex and expensive electronics). Which would bring an enormous saving of the cost of electrical energy.

The article introduces a new solution approach to grid-connected single-stage three-phase PV inverter whereby a dc-link voltage can successfully achieve the desired performance. As a single-stage, the variable output of perturb and observe maximum power point tracking (P&O based-MPPT) is fully utilized as dc-link voltage reference in inverter control scheme. As a result, it is challenging for the dc-link voltage to preserve energy balance by tracking its variable dc-link voltage reference under unpredictable environmental changes. To overcome this challenge, an adaptive reference proportional-integral (ARPI) controller, self-tuning, is designed and implemented to compel the dc-link voltage tracking its voltage reference to be equal as closely as possible; hence, the capability of the dc-link under abnormal events substantially guarantees the best energy balance and transient performance enhancement. To verify the validity of the method, simulation results for multiple events scenarios on 250 KW single-stage grid-connected PV systems show the effectiveness of the ARPI controller compared with PI controller.

The effects of heating rate before solution treatment and cooling rate after solution treatment on the morphological distribution and evolution of precipitation phase of nickel-based single crystal superalloy were studied. The dissolution, precipitation and growth of precipitation phase and matrix phase during heat treatment were analyzed by means of high power scanning electron microscopy. The results show that the morphology of precipitated phase has nothing to do with the distribution of precipitated phase and the heating rate in the heating process, but the cooling rate in the cooling process affects the shape, size and distribution of precipitated phase. The faster the cooling rate, the smaller the precipitated phase is, the more irregular the shape is, the smaller the equivalent edge length is, and the smaller the channel width of matrix phase is.

Single particle tracking (SPT) is a powerful class of methods for studying the dynamics of biomolecules inside living cells. The techniques reveal the trajectories of individual particles, with a resolution well below the diffraction limit of light, and from them the parameters defining the motion model, such as diffusion coefficients and confinement lengths. Most existing algorithms assume these parameters are constant throughout an experiment. However, it has been demonstrated that they often vary with time as the tracked particles move through different regions in the cell or as conditions inside the cell change in response to stimuli. In this work, we propose an estimation algorithm to determine time-varying parameters of systems that discretely switch between different linear models of motion with Gaussian noise statistics, covering dynamics such as diffusion, directed motion, and Ornstein-Uhlenbeck dynamics. Our algorithm consists of three stages. In the first stage, we use a sliding window approach, combined with Expectation Maximization (EM) to determine maximum likelihood estimates of the parameters as a function of time. These results are only used to roughly estimate the number of model switches that occur in the data to guide the selection of algorithm parameters in the second stage. In the second stage, we use change detection (CD) techniques to identify where the models switch, taking advantage of the off-line nature of the analysis of SPT data to create non-causal algorithms with better precision than a purely causal approach. Finally, we apply EM to each set of data between the change points to determine final parameter estimates. We demonstrate our approach using experimental data generated in the lab under controlled conditions.

With the ever-increasing popularity of unmanned aerial vehicles and other platforms providing dense point clouds, filters for identification of ground points in such dense clouds are needed. Many filters have been proposed and are widely used, usually based on the determination of an original surface approximation and subsequent identification of points within a predefined dis-tance from such surface. We present a new filter, Multi-view and shift rasterization algorithm (MVSR) is based on a different principle, i.e., on the identification of just the lowest points in in-dividual grid cells, shifting the grid along both planar axis and subsequent tilting of the entire grid. The principle is presented in detail and compared both visually and numerically to other commonly used ground filters (PMF, SMRF, CSF, ATIN) on three sites with different ruggedness and vegetation density. Visually, the MVSR filter showed the smoothest and thinnest ground profiles, with ATIN the only filter performing comparably. The same was confirmed when comparing ground filtered by other filters with the MVSR-based surface. The goodness of fit with the original cloud is demonstrated by the root mean square deviations (RMSD) of the points from the original cloud found below the MVSR-generated surface (ranging, depending on site, between 0.6-2.5 cm). The MVSR filter performed outstandingly at all sites, identifying the ground points with great accuracy while filtering out the maximum of vegetation/above-ground points. The filter dilutes the cloud somewhat; in such dense point clouds, however, this can be perceived rather as a benefit than as a disadvantage.

With the ever-increasing popularity of unmanned aerial vehicles and other platforms providing dense point clouds, universal filters for accurate identification of ground points in such dense clouds are needed. Many filters have been proposed and are widely used, usually based on the determination of an original surface approximation and subsequent identification of points within a predefined distance from such surface. In this paper, we present a new filter. This Multi-view and shift rasterization algorithm (MVSR) is based on an entirely different principle, i.e., on the identification of just the lowest points in individual grid cells, shifting the grid along both planar axis and subsequent tilting of the entire grid – after each of these steps, one lowest point per cell is detected. The principle is presented in detail and compared both visually and numerically to other commonly used ground filters (PMF, SMRF, CSF, ATIN) on three sites with different ruggedness and vegetation density. Visually, the MVSR filter showed the smoothest and thinnest ground profiles, with ATIN the only filter performing comparably (although the profiles were somewhat thicker and not as complete as MVSR-acquired ground). The same was confirmed when comparing ground filtered by other filters with the MVSR-based surface. The goodness of fit with the original cloud is demonstrated by the root mean square deviations (RMSD) of the points from the original cloud found below the MVSR-generated surface (ranging, depending on site, between 0.6-2.5 cm). ATIN again performed closest to MVSR, with RMSDs of ground filtered points found above MVSR-based surface at individual sites ranging between 4.5-7.4 cm. The remaining filters performed comparable in the simplest flat area but poorly in rugged and much-vegetated sites, with RMSDs above the MVSR surface ranging at such sites from 21 to 95 cm. In conclusion, the novel filter presented in this paper performed outstandingly at all sites, identifying the ground points with great accuracy while filtering out the maximum of vegetation/above-ground points. The filter dilutes the cloud somewhat; in such dense point clouds, however, this can be perceived rather as a benefit than as a disadvantage.

The Chang’e-4 (CE-4) lunar rover, equipped with The Visible and Near-IR Imaging Spectrometer(VNIS) which based on acousto-optic tunable filter spectroscopy, was launched to the far side of the moon on December 8, 2018. The detection band of VNIS ranges from 0.45 to 2.4μm. Because of the weak reflection of infrared radiation from the lunar surface, a static electronic phase-locked acquisition method is adopted in the infrared channel for signal amplification. In this paper, full-link simulations and modeling are conducted of the infrared channel information flow of the instrument. The signal/noise characteristics of VNIS are analyzed in depth, and the signal-to-noise(SNR) ratio prediction and laboratory verification are presented. On January 4, 2019, the VNIS started working successfully and acquired high-resolution spectrum data of the far side of the moon for the first time. Through analysis, the SNR ratio is in line with predictions, and the data obtained by VNIS in orbit are consistent with the information model proposed in this paper.

Biological parameters extracted from electrical signals from various body parts have been used for many years to analyze the human body and its behavior. In addition, electrical signals from cancer cell lines, normal cells, and viruses, among others, have been widely used for the detection of various diseases. Single-cell parameters such as cell and cytoplasmic conductivity, relaxation frequency, and membrane capacitance are important. There are many techniques available to characterize biomaterials, such as scanning tunneling microscopy (STM), nanotechnology, microstrip cavity resonance measurement, dielectric impedance measurement (DEPIM), etc. This article reviews the single cell isolation and sorting techniques, summarizes the common single cell operations such as impedance flow cytometry, cell electrical impedance, electrical impedance sensing, and summarizes the current single cell analysis techniques and their applications.

Viral infections can endanger public health by causing serious illness, leading to pandemics and burdening healthcare systems. Moreover, in the situation of a global spread, disruptions occur in every aspect of life including business, education, and social life. Fast and accurate diagnosis of viral infections has huge implications for saving people’s lives, preventing spread of the diseases, and minimizing social and economic damages. In the last decades, polymerase chain reaction (PCR) based techniques have been frequently used to detect viruses in the clinic. However, in a situation where rapid virus detection is the primary measure in preventing the spread, as in the case of ongoing COVID-19 pandemic, disadvantages of PCR, such as long processing times and requirement of sophisticated laboratory instruments, have been faced. Due to the urgent need for accurate techniques for virus detection, biosensor systems involved in many applications in biological detection are being developed for rapid, real-time, and high-throughput detection of viruses. Among various sensing platforms, optical devices are of great interest due to their advantages such as high sensitivity and direct readout. In the current review, usability of sensing techniques depending on optical phenomena, such as fluorescence-based sensors, surface plasmon resonance (SPR), surface enhanced Raman scattering (SERS), optical resonators and interferometry-based platforms, is discussed for virus diagnostics applications. Then, we focus on an interferometric biosensor developed by our group, single-particle interferometric reflectance imaging sensor (SP-IRIS), which has the capability to visualize single nanoparticles, to demonstrate its application for digital virus detection.

The main property of tripodal ligands is the predictable type of coordination. Homo- and heteroleptic lanthanide complexes with tripodal ligands are a representative class of compounds. However, despite the fact that many of them are paramagnetic their magnetic behavior is poorly understood. This is because their photophysical and catalytic properties have been more attractive. In the present review, we are trying to summarize the available structural information and extremely few data on magnetic properties in order to draw some conclusions about the prospective of tripods using in the design of quantum molecular magnets based on Ln ions. We would like to draw the reader's attention to the fact that despite the consideration of a large part of the currently known lanthanide compounds with tripodal ligands, this review is not exhaustive. However, our goal was to draw the attention of researchers to the fact that a whole niche of air-stable Ln complexes remained outside the attention of magnetochemists and theoreticians.

We consider the problem of scheduling tasks on a single machine subject to an uncertain breakdown to minimize the flowtime. Assume the machine is unavailable during the breakdown; the starting time of the breakdown is a random variable s with distribution function D(s) and the terminating time of the breakdown has no any other information; jobs are non-resumable. Under the assumptions, starting from the perspective of statistical optimization, we first define the expected competitive ratio of an algorithm to find the optimized solution with the considered problem. Further, we propose and prove a certain result on the expected competitive ratio of the SPT rule. In particular, we show that under a quite loose condition the expected competitive ratio of the SPT rule is no more than 5/4. Meanwhile, we also make some discussions about our studies. What we have done will rich and improve the studying results on the area of scheduling to minimize flowtime and advance the development of online optimization and statistical optimization.

As a high-frequency carrier, the Terahertz (THz) wave is essential for achieving high-data-rate wireless transmission due to its ultra-wide bandwidth. Phase stabilization becomes crucial to enable phase-shift-based multilevel modulation for high-speed data transmission. We developed a Mach-Zehnder interferometric phase stabilization technique for photomixing, which has proved a promising method for phase-stable continuous THz-wave generation. However, this method faces inefficiencies in generating phase-modulated THz waves due to the impact of the phase modulator on the phase stabilization system. By photomixing, which is one of the promising methods for generating THz waves, the phase of the generated THz waves can be controlled in the optical domain so that the stability of the generated THz wave can be controlled by photonics technologies. Thus, we have devised a new phase stabilization approach using backward-directional lightwave, which is overlapped with the THz wave generation system. This study presents a conceptual and experimental framework for stabilizing the phase differences of optical carrier signals. We compare the optical domain and transmission performances between forward-directional and backward-directional phase stabilization methods. Remarkably, our results demonstrate error-free transmission at a modulation frequency of 3 Gbit/s and higher.

Per- and polyfluoroalkyl substances (PFAS) are arguably the most common water contaminants in the world today. While several research experiments have been done to understand and remove PFAS from the environment, there is still a lot of unknown. Little has been known about the use of Machine learning (ML) to understand PFAS. This work hence reviews some leading ML approaches and applications in PFAS studies in the distribution, transport, removal, and occurrence predictions of PFAS. Several evaluation matrices were examined and used to perform this function. There are still a lot of areas whereby ML can be used to improve our PFAS knowledge base, some of these were briefly stated in this review.

This paper describes the physico-chemical study of the adsorption of dysprosium (Dy³⁺) in aqueous solution onto two types of activated carbons synthesized from spent coffee ground. KOH activated carbon is a microporous material with a specific BET surface area of 2330 m²·g^-1 and pores with a diameter of 3.2 nm. Carbon activated with water vapor and N₂ is a solid mesoporous, with pores of 5.7 nm in diameter and a specific surface of 982 m²·g^-1. A significant dependence of the adsorption capacity on the solution pH was found, while it does not depend significantly neither on the dysprosium concentration nor on the temperature. A maximum adsorption capacity of 31.26 mg·g^-1 and 33.52 mg·g^-1 for the chemically and physically activated carbons, respectively, were found. In both cases, the results obtained from adsorption isotherms and kinetic study were better fit to a Langmuir model and a pseudo-second-order kinetics. In addition, thermodynamic results indicate that dysprosium adsorption onto both activated carbons is an exothermic, spontaneous and favorable process.

The many-body problem in quantum physics originates from the difficulty of describing the non-trivial correlations encoded in the exponential complexity of the many-body wave function. Motivated by the Giuseppe Carleo's work titled solving the quantum many-body problem with artificial neural networks [Science, 2017, 355: 602], we focus on finding the NNQS approximation of the unknown ground state of a given Hamiltonian $H$ in terms of the best relative error and explore the influences of sum, tensor product, local unitary of Hamiltonians on the best relative error. Besides, we illustrate our method with some examples.

The endometrium, the inner mucosal lining of the uterus, undergoes complex molecular and cellular changes across the menstrual cycle in preparation for embryo implantation. Transcrip-tome-wide analyses have mainly been utilized to study the endometrial receptivity, the prerequisite for successful implantation, with most of the studies, so far, comparing the endometrial transcriptomes between (i) secretory versus proliferative endometrium or (ii) mid-secretory versus early-secretory endometrium. In the current study, we provide the complete transcriptome description of the endometrium across the entire menstrual cycle and, for the first time, comprehensively characterize the proliferative phase of the endometrium. Our temporal transcriptome analysis includes five time points: mid-proliferative, late-proliferative (peri-ovulatory phase), early-secretory, mid-secretory, and late-secretory phases. Thus, we exhaustively unveil the transitions between the consecutive proliferative and secretory phases, highlighting their unique gene expression profiles and possible distinct biological functions. Transcriptome analysis reveals many differentially expressed genes (DEGs) across the menstrual cycle, most of which are phase-specific. As an example of the coordinated gene activity, the expression profile of his-tone-encoding genes within the HIST cluster on chromosome 6 showed an increase in cluster activity during the late-proliferative and a decline during the mid-secretory phase. Moreover, numerous DEGs are shared among all phases. In conclusion, in the current study, we delineate the endometrial proliferative phase-centered view of transcriptome dynamics across the menstrual cycle. Data analysis highlights significant transcriptomic and functional changes occurring during the late-proliferative phase – an essential transition point from the proliferative to the secretory phase. Future studies should explore how the biology of the late-proliferative phase endometrium impacts the achievement of mid-secretory endometrial receptivity or contributes to molecular aberrations leading to embryo implantation failure.

Background: Biological processes are based on complex networks of cells and molecules. Single cell multi-OMICs is a new tool aiming to provide new incites in the complex network of events controlling the functionality of the cell.; Methods: Since single cell technologies provide many sample measurements, they are the ideal environment for the application of deep learning and machine learning approaches. An autoencoder (AE) is composed of an encoder and a decoder sub-model. AE are very powerful in data compression and noise removal. However, the decoder model remains a black box from which is impossible to depict the contribution of the single input elements. We have recently developed a new class of autoencoders, called Sparsely Connected Autoencoders (SCA), which have the advantage of providing a controlled association among the input layer and the decoder module. This new architecture has the benefit that the decoder model is no anymore a black box and it can be used to depict new biologically interesting features from single cell data; Results: In this paper, we show that SCA hidden layer can grab new information usually hidden in single cell data, like as providing clustering on meta-features difficult, i.e. transcription factors expression, or impossible, miRNA expression, to depict in single cell RNAseq data. Furthermore, a SCA representation of cell clusters has the advantage of simulating a conventional bulk RNAseq, which is a data transformation allowing the identification of similarity among independent experiments; Conclusions: In our opinion, SCA represent the bioinformatics version of a “Swiss Army knife” for the extraction of hidden knowledgeable features from single cell OMICs data.

In this research, atomistic molecular dynamics simulations are combined with mesoscopic phase-field computational methods in order to investigate phase-transformation in polycrystalline Aluminum microstructure. In fact, microstructural computational modeling of engineering materials could help to optimize their mechanical properties for industrial applications (e.g. directional solidification for turbine blades). As a result, a multiscale modeling approach is developed to find a relation between manufacturing variables (e.g. temperature) and microstructural properties of crystalline materials (e.g. grain size), which could be used to develop an advanced manufacturing process for sensitive applications. The results show that atomistic modeling of grain growth could be used as a first-principle approach in order to study phase transformation's kinetics, which could capture morphology of polycrystalline materials more accurately. On the other hand, phase-field mesoscopic approach needs less computational efforts, but still it relies on semi-empirical data to capture accurate phase transformation regimes, which makes this approach suitable for rapid examining of new manufacturing conditions as well as its effects on microstructural properties of polycrystalline materials.

Although early work on parental burnout in the 1980s did not link parental burnout to specific parenting situations, the idea that parents affected by specific vulnerability factors were particularly at risk of burnout quickly emerged. Based on the etiological model of parental burnout (i.e., the balance between risks and resources), the objective of this study was to determine if there were specific vulnerability factors that significantly increase the risk of parental burnout. 2,563 parents participated in the study. We compared parents with a child with special needs (n = 25), parents who had adopted a child (n = 130), and single parents (n = 109), to strictly matched control groups of parents. Parents with a child with special needs displayed higher burnout and lower balance between risk and resources than the control group; parents with an adopted child had similar levels of both parental burnout and balance; and single parents had higher parental burnout but similar balance. Parents who combined specific several vulnerability factors were at greater risk of burnout. Single parenthood and adoption do not in themselves trigger a process leading de facto to other risk factors, but having a child with special needs does.

Complex systems exhibit critical thresholds at which they transition among alternative phases. Complex systems theory has been applied to analyze disease progression, distinguishing three stages along progression: (i) a normal non-infected state, (ii) a pre-disease state in which the host is infected and responds; therapeutic interventions could still be effective, (iii) an irreversible state, where the system is seriously threatened. The Dynamical Network Biomarker (DNB) theory sought for early-warnings of the transition from health to disease. Such DNBs might range from individual genes to complex structures in transcriptional regulatory or protein-protein interaction networks. Here we revisit transcriptomic data obtained during infection of tobacco plants with tobacco etch potyvirus to identify DNBs signaling the transition from mild/reversible to severe/irreversible disease. We identified genes showing a sudden transition in expression along disease. Some of these genes cluster in modules that show the properties of DNBs. These modules contain both genes known to be involved in response to pathogens (e.g., ADH2, CYP19, ERF1, KAB1, LAP1, MBF1C, PR1, or TPS5) and other genes not previously related to biotic stress responses (e.g., ABCI6, BBX21, NAP1, OSM34, or ZPN1).

When ground-penetrating radar is used to detect targets within concrete, the location of the targets, the identification of different shapes, properties and less obvious echoes all greatly increase the interpretation time of the staff and can easily cause misjudgment of the echo images. In this paper, the ground-penetrating radar echo images (B-scan) after processing are mean filtered to eliminate the direct waves that interfere greatly with the echoes. The RFB-s structure is added to the YOLOv3-SPP network structure, while the Anchor value is optimized and the EIOU loss function is introduced. For four types of data with different shapes and properties at random target locations, three models, YOLOv3, YOLOv3-SPP and the improved YOLOv3-SPP, are used for classification and identification, and the proposed algorithm models are comprehensively evaluated using model evaluation metrics. The experimental results show that the algorithm models proposed in this paper have good recognition effect in ground-penetrating radar echo image target detection.

Debris-flows are recurrent events on mountain- and hill- slopes, and they have been the object of numerous field investigations and sampling, however most of this work reposes on imagery and outcrop analysis, in such a way that there are still only a handful of studies investigating the internal architecture of these events’ deposits. In the present contribution, we aims at underneath the internal structure of a portion of a debris-flow deposit that was accessible in the aftermath of the 2018 heavy-rainfall debris-flows in Hiroshima Japan. Using a Ramac Pro-Ex GPR with 500 MHz and 800 MHz antenna, a set of longitudinal and transversal transects was used to characterize the deposit. The results demonstrated that a set of subhorizontal layers have filled the valley, and interacting with local terrace edges, these layers have piled up and overcome the obstacle. Across the valleys, a set of trough suggest the presence of channels that were also filled during the event. Finally, in the channel post-event, a set of radargram “cross-bedded units” shows that the final deposition in the channel was of a more dilute flow, typical of a Newtonian flow. This set of units was not to be found at the surface of the post-event pseudo-surface, suggesting that the flow ended as a debris-flow on this surface, and that it is only when the flow dug the final channel that the nature of the flow returned from debris-flow to Newtonian flow.

The paper presents experimental studies on the geophysical survey of Almaty – Nur-Sultan highway sections, which located 100 km. from Almaty, Almaty region of the Republic of Kazakhstan. As the object of study selected highway sections in 3 places: on the highway section with a well-preserved coating to identify layers; on the highway section with obvious damage (with holes, potholes, horizontal and grid cracks); on the section of the highway with a drainage pipe. Since the formulation of the problem requires the use of a non-destructive, fast method that gives an idea of the layer structures with an accuracy of ± 0.1 m., experimental studies were conducted using the ground penetrating radar (GPR) «Loza B» using different antennas, with different profile steps for accuracy. The results of the geophysical survey of the structure of the underlying layers and asphalt for the detection of defects and their causes are presented. The results of this work can be used to develop compositions of asphalt concrete mixtures with high temperature stability, strength and durability, considering the climatic conditions in order to ensure the safety of road surfaces during operation.

The coastal dry zone areas of Sri Lanka mostly rely on ground water as the potable drinking water source because pipe born water is rarely provided. Most of the domestic units construct dug wells adjacent to houses where the ground water is exposed to fecal contamination due to pit – latrines. There available standards and commonly accepted factors regulating the construction of ground water extraction sources yet there is lack of evidence whether following them effectively prevent ground water fecal contamination. This research focus on applicability of commonly accepted factors on preventing the pit latrines correlated ground water contamination, taking twenty (20) sampling locations of Kalpitiya Peninsula of Sri Lanka as the case study area. The ground water was tested for Total coliform bacteria at 37 °C and E.Coil at 44 °C to identify the water quality level related to fecal contamination. The depth of water table, gap of infiltration layer, depth of latrine pit and distance between dug well and latrine pit were identified as the most commonly considered factors. Accordingly, case specific and area specific reasons apart from the ‘commonly accepted factors’ are highly influencing the pit latrines correlated ground water contamination in Kalpitiya Peninsula, Sri Lanka.

This paper provides a comparative study between microwave tomography and synthetic time-reversal imaging techniques as applied to ground penetrating radar (GPR) surveys. The comparison is carried out by processing experimental data collected at a controlled test site, with various types of buried targets at given subsurface depths and representative soil conditions. It is shown that the two techniques allow us to obtain complementary information about position, depth and size of the targets from a single GPR survey.

The frequency synthesizer is a critical component in Cs beam clock technology. In this paper, we present a demonstration of a direct microwave frequency-synthesis chain for a cesium-beam atomic clock, which utilizes frequency multiplication and a dual-phase-locked loop mode. A detailed analysis of the frequency-synthesis chain is conducted, and a mathematical model is established. The phase settling time and system stability are simulated, measured, and verified. The experimental results for the phase settling time align with the simulation outcomes. The phase settling time can be adjusted within the range of 644.5 µs to 1.5 ms, and the absolute phase noise values are -63.7 dBc/Hz, -75.7 dBc/Hz, -107.1 dBc/Hz, and -122.5 dBc/Hz at 1 Hz, 10 Hz, 1 kHz, and 10 kHz offset frequencies, respectively. Additionally, the Ramsey fringes are detected, and the Allan deviations of the 10 MHz output from the cesium-beam atomic clock are measured to be 2.99×10−12 at 1s and 8.02×10−14 at 10,000 s.

Single-molecule magnets (SMMs) have garnered significant interest in the field of molecular magnetism due to their unique magnetic properties at the nanoscale. These molecular systems exhibit magnetisation behaviour reminiscent of conventional bulk magnets but with distinct advantages such as size-dependent properties and potential applications in quantum computing and high-density data storage. However, challenges remain in harnessing their properties for practical applications, including their susceptibility to degradation and limited control over their assembly and organisation.

This year marks the 20th anniversary of the discovery that proteins with various cellular functions can be temporarily immobilized in the nucleolus, a process known as nucleolar sequestration. This review reflects on the progress made to understand the physiological roles of nucleolar sequestration and the mechanisms involved in protein immobilization. We discuss how nucleolar sequestration consists of a highly choreographed amyloidogenic liquid-to-solid phase transition that converts the nucleolus into Amyloid bodies (A-bodies). The study of solid condensates A-bodies will offer unique perspectives on cellular assembly of membrane-less compartments and provide alternative insights on pathological amyloidogenesis involved in neurological disorders.

The folding of certain proteins (e.g., enzymes) into perfectly defined 3D conformations via multi-orthogonal interactions is critical to their function. Concerning synthetic polymers chains, the “folding” of individual polymer chains at high dilution via intra-chain interactions leads to so-called single-chain nanoparticles (SCNPs). This review article describes the advances carried out in recent years in the folding of single polymer chains into discrete SCNPs via multi-orthogonal interactions using different reactive chemical species where intra-chain bonding only occurs between groups of the same species. First, we summarize results from computer simulations of multi-orthogonally folded SCNPs. Next, we comprehensively review multi-orthogonally folded SCNPs synthesized via either non-covalent bonds or covalent interactions. Finally, we conclude by summarizing recent research about multi-orthogonally folded SCNPs prepared through both reversible (dynamic) and permanent bonds.

ACE2, the putative receptor for the novel coronavirus (2019-nCoV), played an important role in cell entry of 2019-nCoV. However, it is not yet clear what cell types within the human body express ACE2. Here, a systematic analysis was undertaken using published single cell datasets. In total, our study analyzed 229652 cells, from five different organs, derived from 88 donors. The top ACE2 expressing cells include proximal tubule cells in the kidney and enterocytes in the intestine. Other major ACE2 expressing cells in the kidney include podocytes, intercalated cells and endothelial cells. Our results offer a comprehensive atlas of ACE2 expression at the single cell level and unravel the enormous potential targets of 2019-nCoVinfection beyond the lung.

Clean use of photons from light to activate chemical reactions offer many possibilities in different fields, from chemistry and biology to materials science and medicine. This review article describes the advances carried out in last decades toward the phototriggered synthesis of single-chain polymer nanoparticles (SCNPs) as soft nanomaterials with promising applications in enzyme-mimicking catalysis and nanomedicine, among other different uses. First, we summarize different strategies developed to synthesize SCNPs based on photoactivated intrachain homocoupling, phototriggered intrachain heterocoupling and photogenerated collapse induced by external cross-linker. Next, we comprehensively review the emergent topic of photoactivated multifolding applied to SCNP construction. Finally, we conclude by summarizing recent strategies towards phototriggered disassembly of SCNPs.

Large Language Models (LLMs) have proved significant proficiency when comes to code generation especially in Structured Query Language (SQL) for databases and recent successful Text-to-SQL method involves fine-tuning pre-trained LLMs for SQL generation tasks. Transforming natural language text into SQL queries, has been attempted to solve with various learning techniques including Few-shot learning[1], fine tuning. In this paper we propose Supervised fine-tuning (SFT) as a better alternative for learning technique for text-to-SQL generation task using Code-Llama that pushes state of art accuracy on spider test suite to 89.6% on dev set which represent first instance of surpassing the earlier best-in-class with 5.5% higher score and 86.8% of exact match accuracy on dev set. Furthermore, we demonstrate that properly prompted LLM along with SFT provides far fewer hallucinations and much more robust LLM that can be used as a general tool for any text-to-SQL generation use case.

In Chronic Myeloid Leukemia (CML) patients, CD34+/CD38-/CD26+ cell population represents a “CML specific” Leukemia Stem Cell (LSC) compartment. Indeed, preliminary studies showed that the expression of CD26 discriminates bone marrow CML Leukemic Stem Cells (LSCs) from nor-mal Hematopoietic Stem Cells (HSCs) or from LSCs of other myeloid neoplasms. We were first to demonstrate that at diagnosis CD34+/CD38-/CD26+ cells are easily measurable also in Peripheral Blood (PB) and that residual circulating CD26+LSCs persist, with a fluctuating trend, in most pa-tients in optimal response during treatment with Tyrosine Kinase Inhibitors (TKIs) and even after successful TKI discontinuation. These data corroborate and confirm the possibility of using flow-cytometry CD26+ evaluation as an important diagnostic tool that, combined with molecular biology and cytogenetic, could provide a rapid diagnosis of Chronic Phase (CP) CML starting from a simple PB sample. Yet, few data are available regarding the behavior of CD26+LSCs during Accelerated Phase (AP) or Blast Phase (BP) CML and the role, if any, this peculiar staminal cell compartment may play in disease progression. In the present study we compared the presence and phenotypic characteristics of circulating CD26+LSCs in CP CML patients at diagnosis, during AP and in cases of progression to lymphoid BP, inquiring a possible role of these cells during dis-ease evolution.

This study aims to elucidate the influence of meteorological conditions on particle levels in Cergy-Pontoise. It explores the temporal variability of PM10 pollution days by associating them with the vertical temperature profile derived from conventional radiosondes from 2013 to 2022 (regional station). The results indicate that nearly 80% of exceedance days were associated with thermal inversions, primarily observed in winter and typically lasting 1 to 3 days. Analysis of winter thermal inversion characteristics suggests that those linked to pollution primarily occur near the ground, with higher intensity in December (12.1°C) and lower in February (10.3°C). Persistent inversions (extended nocturnal by diurnal inversion) account for 91.4% of the total inversions associated with high concentrations. Captive balloon soundings and temperature measurements at different altitudes were conducted during the winter of 2022/2023 to clarify thermal inversion in the Oise Valley at the center of Cergy-Pontoise. The results highlight three nocturnal wind circulation mechanisms in the valley, including downslope flow, circulation influenced by an urban heat island, and mechanical air evacuation under an inversion layer towards the less steep East side of the valley. Analysis of PM with the temperature gradient in the Oise Valley shows a significant correlation, suggesting an increase in concentrations during locally detected inversions and a decrease during atmospheric disturbance.

The main goal of the research is to assess the effectiveness of aerial ground-penetrating radar (GPR) in delineating boundaries between disturbed clayey ground and rock formations along the old Wadi. The study also tackles technical challenges associated with drone-based GPR applications in urban open areas, considering geological heterogeneity, topographic variations, and environmental conditions. The potential of using drone-based GPR equipped with an unshielded dipole antenna as a transformative tool in geospatial analysis was demonstrated. The research encompasses academic insights and field borehole drilling experiments to validate the accuracy and reliability of drone-based GPR data in real-world scenarios. Anticipated contributions include advancements in understanding drone-based GPR technology for mapping disturbed soil boundaries in foundation engineering applications and other relevant areas and recommendations for optimizing its performance in challenging terrains.

In this study, an experiment was conducted on hoop pine (Araucaria cunninghamii), which is a common tree species in Taiwan. Holes with diameters of 4, 5, 7, 10, 12, and 14 cm were drilled in dry hoop pine timber with a diameter of 39 cm and a height of 57 cm, and an 800 MHz Ground Penetrating Radar (GPR) antenna were used to determine the minimum image resolution and the size of the holes in the wood. GPR images of the timber were subjected to a filtering process to obtain characteristic reflection curves of the damage to the timber. Curves with clear waveforms were observed in the GPR profiles of eccentric holes with a diameter of 4 cm. Profiles of the damage were obtained and profile images with the trunk radius at the centre were transformed into polar coordinate images. From these polar coordinate images, the location, size and diameter of the eccentric holes in the wood were identified, and the reflection curves were characterised by waveforms and irregular fluctuations. The risk levels of tree trunks were determined on the basis of their t/R (minimum normal wall thickness of the cross-section of the trunk/radius of the trunk) values and hole area ratios. A comparison between the GPR-based results and the actual diameters of the holes revealed that the filtered GPR profiles could be used for the efficient and accurate assessment of damage to hoop pine timber (average error rate ≤ 4%).

Soil transverse isotropy results in different stiffness characteristics in the horizontal and vertical directions. However, the effect is usually neglected in the seismic motion analysis. In this study, an equivalent linear anisotropic soil model was established based on the finite element method and investigated the impact of anisotropic parameters on ground motion at the site under various seismic wave inputs. It is found that the anisotropic parameters have a more significant effect for the seismic waves with the dominant frequency closer to the fundamental frequency of the site. As an example, the soil dynamic parameters in Shanghai Yangshan Port were calibrated by a series of bending elements, resonance columns, and cyclic triaxial tests. The influences of anisotropy on the peak ground acceleration (PGA) and response spectrum are studied for Yangshan Port. Addi-tionally, the standard design response spectra considering the soil anisotropy were provided. A comparison reveals that the existing isotropic design response spectrum may lead to dangerous seismic design for the structures at Yangshan port.

The practical utility of remote sensing techniques relies on validating them with ground-truth data. Validation requires similar spatial-temporal scales for ground measurements and remote sensing resolution. Evapotranspiration (ET) estimates are commonly compared to weighing lysimeter data, which provide precise but localized measurements. To address this limitation, we propose using superconducting gravimeters (SG) to obtain ground-truth ET data at larger spatial scales. SG measure gravity acceleration with high resolution (tenths of nm/s2) within a few hundred meters. Similar to lysimeters, gravimeters provide direct estimates of water mass changes for determining ET without soil disturbance. To demonstrate the practical applicability of SG data, we conducted a case study in Buenos Aires Province, Argentina (-34.87, -58.14). We estimated cumulative ET values for 8-day and monthly intervals using gravity and precipitation data from the study site. Comparing these values with MODIS-based ET products (MOD16A2), we found a very good agreement at the monthly scale, with an RMSE of 32.6 mm/month (1.1 mm/day). This study represents progress in using SG for hydrogeological applications. The future development of lighter and smaller gravimeters is expected to further expand their use.

The sinking of cavities in urban areas is a very important geological risk to which many towns in Puglia are exposed. The study, mapping, geological and speleological description, classification and cataloging of forms and types of cavities is of fundamental importance for each urban center because it is linked to past local anthropic and natural processes, unique to each site. All this could lead to an enhancement of existing underground cavities in urban areas through conservation and continuous monitoring. Unfortunately in many cases these underground cavities have been used as landfills and subsequently abandoned. One of these cavities at the end of March 2007 collapsed in the inhabited center of Gallipoli causing damage to the structures and fortunately not to human lives. In the area relating to the collapsed cavity, a series of geophysical investigations were undertaken with the use of ground penetrating radar methodology in an attempt to delimit the area of collapse and understand the possible types of interventions for restoring the area. In the same area the measures were repeated 16 years later (December 2022) due to another collapse. The results show a much more widespread danger situation.

Desertification and dune progression over vegetation is quantified using remote sensing data, but vegetation, eventually temporarily, buried under sand blowout may escape such assessment, and to estimate the extent of buried vegetation, a GPR campaign was conducted over the coastal sand-dune of Tottori Prefecture (Japan) in combination with a high-resolution topographic UAV-based survey of the topography. The result shows that buried vegetation exists underneath sand-blowout, especially near the dune ridges, and that this vegetation can extend 20 – 30 m further than the estimation made from airborne remote sensing. Furthermore, the presence of palaeo-vegetation in palaeodune layers also provide information on the long-term evolution of sand dunes (with periods of stability vs rapid change), which can be used to reconstruct Quaternary coastal environments.

The air pollutant NO2 is derived largely from transportation sources and is known to cause respiratory disease. A substantial reduction in transport and industrial processes around the globe from the novel SARS-CoV-2 coronavirus and subsequent pandemic resulted in sharp declines in emissions, including for NO2. Additionally, the COVID-19 disease that results from the coronavirus may present in its most severe form in those who have been exposed to high levels of air pollution. To explore these links, we compared ground-based NO2 sensor data from 11 US cities from a two-month window (March-April) over the previous five years versus the same window during 2020 shutdowns. NO2 declined roughly 12-41% in the 11 cities. This decreased coincided with a sharp drop in vehicular traffic from shutdown-related travel restrictions. To explore this link more closely, we gathered more detailed traffic count data in one city, Indianapolis, Indiana, and found a strong correlation between traffic counts/classification and vehicle miles travelled, and a moderate correlation between NO2 and traffic related data. This finding indicates that we can use such analysis in targeting reduction in pollutants like NO2 by examining and manipulating traffic patterns, thus potentially leading to more population-level health resilience in the future.

Allometric equations are used to estimate accurate biomass and carbon stock of forests. However, in Ethiopia only few allometric equations as compared to its floral diversity and species-specific allometric equations for Acacia species are still not developed in Ethiopia. The numbers of tree marked for sampling are Fifty-four (54) using preferential sampling. Diameter at breast height, wood density and tree height were collected as independent variables to predict species specific dry biomass of Acacia species. The new species-specific allometric models have been performed using linear regression analysis in the R software. The Above ground biomass (AGB) have been validated using quantitative statically using the pantropic model. Six candidate models have been developed for each species and four best models for each species of dry biomass was selected based on goodness-of-fit statistics and equation performance analysis of the candidate models. The best model for predicting above ground biomass for Acacia seyal is 0.20636*((DBH²)Hρ) ^0.53167, for Acacia polyacantha is 7.26982((DBH)²Hρ)^0.21750, for Acacia ethibcia is 29.01898*((DBH)²Hρ)^0.21518 and for Acacia toritolis is 3.82427*((DBH)²Hρ)^0.16748. The selected models are the best performing (P> 0.01) and higher adjusted R² (>80%) and has lower Akaike’s Information Criteria (AIC) and residual standard error (RSE) values as comparing the rest of the model. The validation of new developed biomass model using Tukey test indicated that significant variation of mean biomass (P<0.05) between the new developed model and the generalized model. The statistics model performance analysis of Nash-Sutcliffe efficiency (NSE) value is approaching to one, indicating that the new developed model has better performance model as compared with generalized model. Moreover, the percent bias of the new developed models is close to zero which indicates that the site-specific biomass models have more accurate estimator and the generalized biomass models have overestimated biomass for the four Acacia species.

Electrospun ultrathin fibers based on binary compositions of polylactide (PLA) and poly(ε-caprolactone) (PCL) with different ratios of polymer components from 0/100 to 100/0 wt. % were studied. Using a combination of thermal (DSC) and relaxation (EPR) measurements, the effect of biopolymers content on the characteristics of the crystal structure of PLA and PCL and the diffusive rotational mobility of the stable TEMPO radical in the amorphous regions of PLA/PCL compositions was shown. It was revealed that after PLA and PCL blending, significant changes in the degree of crystallinity of PLA, PCL segmental mobility, sorption capacity of the radical as well as activation energy of rotational diffusion in the amorphous regions of PLA/PCL composition are observed. The characteristic region of biopolymers’ composition from 50/50 to 30/70 % PLA/PCL blends ratio was found, where the inversion transition of PLA from dispersive medium to dispersive phase where an inversion transition is assumed when the continuous medium of the PLA transforms into a discrete phase. The performed studies made it possible for the first time to carry out a comprehensive analysis of the effect of the system component ratio on the structural and dynamic characteristics of the PLA/PCL film material at the molecular level.

The research paper provides a mathematical framework for understanding phase shift in wave phenomena, bridging theoretical foundations with real-world applications. It emphasizes the importance of phase shift in physics and engineering, particularly in fields like telecommunications and acoustics. Key equations are introduced to explain phase angle, time delay, frequency, and wavelength relationships. The study also introduces the concept of time distortion due to a 1° phase shift, crucial for precise time measurements in precision instruments. The research also addresses infinitesimal wave energy loss related to phase shift, enriching our understanding of wave behavior, and impacting scientific and engineering disciplines.

We investigate numerically the interactions of in-phase Airy beams modulated by a fundamental Gaussian beam and fourth-order diffraction in Kerr nonlinear media. Directly numerical simulations show that normal (anomalous) fourth-order diffractions and in-phase (out-of-phase) Gaussian beam affect the interactions of solitons generated from Airy beams in unique manners. Different from previous results that interactions between in-phase (out-of-phase) conventional beams are always attractive (repulsive), many anomalous interactions of Airy beams are obtained. Stable bound states of breathing Airy soliton pairs can be formed with the help of fourth-order diffraction and fundamental Gaussian beam.

Using coherent optical detection and digital signal processing, laser phase noise and equalization enhanced phase noise can be effectively mitigated using the feed-forward and feed-back carrier phase recovery approaches. In this paper, theoretical analyses of feed-back and feed-forward carrier phase recovery methods have been carried out in the long-haul high-speed n-level phase shift keying (n-PSK) optical fiber communication systems, involving a one-tap normalized least-mean-square (LMS) algorithm, a block-wise average algorithm, and a Viterbi-Viterbi algorithm. The analytical expressions for evaluating the estimated carrier phase and for predicting the bit-error-rate (BER) performance (such as the BER floors) have been presented and discussed in the n-PSK coherent optical transmission systems by considering both the laser phase noise and the equalization enhanced phase noise. The results indicate that the Viterbi-Viterbi carrier phase recovery algorithm outperforms the one-tap normalized LMS and the block-wise average algorithms for small phase noise variance (or effective phase noise variance), while the one-tap normalized LMS algorithm shows a better performance than the other two algorithms for large phase noise variance (or effective phase noise variance). In addition, the one-tap normalized LMS algorithm is more sensitive to the level of modulation formats.

Background DaVinci Single-Port (SP) robotic surgery offers several benefits compared to traditional multiport laparoscopic or robotic surgeries. One of the main advantages is that it allows for a minimally invasive approach, resulting in a single, smaller incision and reduced trauma to the patient’s body leading to less postoperative pain, faster recovery, and reduced risk of complications. The cosmesis of a single port with minimal visible scarring is also an attractive aspect to the patients; however, many surgeons use an additional port for energy device, stapler use, and drain insertion. Pure single port surgery with one incision is still rare. Here we share our experience of first 10 cases using SP robotic platform in colorectal surgery. Methods From May 2023 to December 2023, colorectal patients who underwent SP-robotic surgery were analyzed. Placement of the incision was umbilicus for 8 patients, and right lower quadrant for 2 patients through which ileostomy maturation was performed. Data including perioperative parameters and postoperative outcomes were analyzed with a median follow-up of 4.6months (range 0.6-7.4months). Results A total number of 10 colorectal patients underwent DaVinci Single-Port robotic colorectal surgery at our institution during this period. Demographics of the patients showed 4 males (40%) and 6 females (60%) with a median age of 63.5years (range 50-75years). Median body mass index (BMI) was 22.89kg/m2 (range 19.92-26.84kg/m2), and 9 patients were diagnosed with colorectal cancer and 1 patient was diagnosed with rectal gastrointestinal tumor. One patient underwent anterior resection and cholecystectomy simultaneously. Mean operation time was 222min (range 142-316min), and mean wound size was 3.25cm (range 2.5-4.5cm). Nine patients underwent surgery with single incision through which single port trocar was inserted, and one patient had one additional port for drain insertion. Mean hospital stay was 6 days (range 4-8 days) with 1 postoperative complication of bleeding requiring transfusion, but there was no re-admission within 30 days. Conclusion Overall, our experience with single-port robotic colorectal surgery has been promising. With only one patient with additional port for drain insertion, all nine patients underwent SP-robotic surgery with single incision for colon as well as rectal surgeries. Compared to an average postoperative length of stay of 6.5-8 days in laparoscopic colorectal surgeries reported in literature, SP-robotic surgery showed faster recovery of 6 days highlighting its benefits in patient recovery and satisfaction.

This study investigated the influence of nutrient inputs and their timing on saffron yield and quality. The study was conducted from 2016 to 2020 and involved the application of eight different fertilization treatments at various stages of saffron growth. These treatments included single doses in Autumn (A), Winter (W), and Spring (S); double doses in Winter-Spring (AW), Autumn-Spring (AS), and Winter-Spring (WS); and a triple dose in Autumn-Winter-Spring (AWS). A control group (C) received no fertilizer. A compound fertilizer with a 15-15-15 composition was applied across all treatments, with nitrogen (N) rates of 67.5 kg/ha for single doses (A, W, S), 135 kg/ha for double doses (AWF, ASF, WSF), and 202.5 kg/ha for the triple dose (AWSF). Similar rates were applied for phosphorus (P) and potassium (K). The findings demonstrated that fertilization generally enhanced saffron attributes. The triple dose treatment yielded the most effective results. The timing of fertilization also played a crucial role, as split applications during different growth stages led to higher production especially winter fertilization. However, spring fertilization had limited impact due to decreased plant activity and reduced nutrient absorption during that period. Although the yield increased, the qualitative aspects of saffron, including color (crocin), taste (picrocrocin), and aroma (safranal), were not significantly influenced by the fertilization treatments. Nevertheless, these attributes remained within the natural limits defined by ISO-3632, indicating that fertilization practices did not compromise saffron quality. Our study highlights the significance of nutrient inputs and their timing in optimizing saffron yield. It provides valuable insights for developing efficient fertilization programs to enhance saffron production while preserving its quality characteristics.

Background. In the central-eastern region of the Mediterranean island of Sardinia more than two decades ago, a mountain area was identified where the population displays exceptional longevity, especially among men (the longevity Blue Zone, LBZ). This community was thoroughly investigated seeking to understand the underlying factors of this phenomenon. In the present study, 11 genetic markers previously associated with longevity in several long-lived populations were analyzed. Methods. APOE (rs429358 and rs7412), APOE promoter (rs449647, rs769446, and rs405509), ACE1 (rs1799752), IL6 ‒174G/C (rs1800795), TNFα ‒308G/A (rs1800629), FOXO3A (rs2802292), KLOTHO (rs9536314) and G6PD (c.563C→T) were investigated. PCR-based genotyping was performed following genomic DNA extraction from 150 nonagenarians living in the LBZ and 150 controls from a nearby area. Results. No significant deviation of the frequency of the analyzed markers was detected between the two groups except a weak association with the –174G&gt;C gene variant of the IL-6 gene (p=0.040), a major modulator of the inflammatory response. Conclusions. The findings of this study do not support a significant association of known genetic variants on survival in the population of the Sardinian LBZ. Other genetic or epigenetic traits might play a role not yet identified.

Sperm gain fertilization ability and forward movement characteristics during epididymal transport. Sperm maturation is inseparable from the processing of the epididymis. Compared with other reproductive organs, relatively little is known about the epididymis. However, with the development of molecular biology and the improvement of single-cell sequence technology, we gradually realized that we should re-examine the importance of the epididymis for sperm mat-uration and for the entire male reproductive system. Recently, epididymis related reports have tended to be more regionalized and more refined. We can understand cell distribution and gene expression from the perspective of a single cell. It has been reported that different regions of the epididymis have different functions and different cell compositions, which may be determined by gene expression. Here, we comprehensively reviewed the epididymal studies. From the ana-tomical structure of the epididymis to the division of its regions, we focused on the cell compo-sition and region-specific genes differentially expressed in the epididymis. The gene expression of the epididymis extends to a series of biological processes of sperm in the epididymal cavity, and the serious effects of epididymal diseases on reproduction are discussed. Therefore, the importance of the epididymis in male reproduction is emphasized. With the maturity of single-cell spatial transcriptomics, it is hoped that the technology can be applied to epididymal research and bring about the spatiotemporal landscape of the epididymis at the single-cell level.

The strong coupling between individual quantum emitters and resonant optical micro/nanocavities is beneficial to understand light and matter interactions. Here we propose a plasmonic nanoantenna placed on a metal film to achieve an ultra-high electric field enhancement in the nanogap and ultra-small optical mode volume. The strong coupling between a single quantum dot and the designed structure is investigated in detail by both numerical simulations and theoretical calculations. When a single QD is inserted into the nanogap of the silver nanoantenna, scattering spectra show remarkably large spectral splitting and typical anti-crossing behavior of the vacuum Rabi splitting, which can be realized in the scattering spectra by varying the nanoantenna thickness. Our work shows a possible way to enhance light-matter interaction at a single quantum emitter limit, which can be useful for future quantum and nanophotonic applications.

Long-read single-molecule sequencing has revolutionized de novo genome assembly and enabled the automated reconstruction of reference-quality genomes. It also has been widely used to study structural variants, phase haplotypes and more. Here, we introduce the assembler— SMARTdenovo, which is an SMS assembler that follows the overlap-layout-consensus (OLC) paradigm. SMARTdenovo (RRID: SCR_017622) was designed to be a fast assembler that did not require highly accurate raw reads for error correction, unlike other, contemporaneous SMS assemblers. It has performed well for evaluating congeneric assemblers and has been successful for a variety of assembly projects. It is compatible with Canu for assembling high-quality genomes, and several of the assembly strategies in this program have been incorporated into subsequent popular assemblers. The assembler has been in use since 2015, and here we provide information on the development of SMARTdenovo and how to implement its algorithms into current projects.

An experiment was conducted to investigate the role of single nucleotide polymorphisms of the gene RNF34 3′UTR-588 G>A and RNF128 I1-2380C>T with carcass and meat quality traits of Chinese Simmental-cross steers. METHOD: We performed sequencing and restriction enzyme digestion to detect genotypes of RNF34 3′UTR-588 G>A and RNF128 I1-2380C>T. Then, we analyzed the association of novel single nucleotide polymorphisms in intron regions of the RNF128 gene and in the 3′UTR region of RNF34 and meat quality traits of Chinese Simmental-cross steers. RESULTS: Statistical analyses revealed that SNP of RNF128 (I1-2380C>T) was significantly associated with dressed weight, forepaw weight, carcass depth, carcass brisket depth, hind legs length (P<0.05), etc. And RNF34 (3′UTR-588 G>A) were significantly associated with testis weight, kidney weight, tare weight (P<0.05), etc. CONCLUSION: Our findings suggest that polymorphisms in RNF34 and RNF128 might be important genetic factors that influence carcass and meat quality in beef cattle. Thus, they might be useful markers for meat quality traits in future marker-assisted selection programs in beef cattle breeding and production.

In this work, we studies the principle of ground electrode current field through ground communication technology, signal design, and optimal working mode of excitation source, so as to adapt the working mode, working frequency, and transmission medium condition of signal transmission. Through waveform design, energy is concentrated in the main conduction direction, which is beneficial for signal filtering at the receiving end and achieving high reliability data transmission; On this basis, on-site environmental testing was conducted to verify the detection and recognition technology of weak signals. Signal design and detection recognition are a very important part of the grounding electrode current field through ground communication technology. The grounding electrode current field through ground communication technology is mainly applied to solve the problem of communication between rescue personnel and trapped personnel before and during tunnel engineering collapse and rescue.

Pakistan relies mostly on fossil fuel for fulfilling its energy demand which is expensive as 11 well as not friendly for the environment. The need of the hour is to shift from fossil fuels to renew-12 able energy resources like geothermal, wind, solar etc. to cater for global warming issues. Pakistan 13 has a lot of potential geothermal sites because of several fault lines and hot springs. A sound 14 knowledge of ground temperature is essential to use geothermal energy, which is obtained by drill-15 ing boreholes and putting sensors making it an expensive procedure. Thus, to avoid huge cost for 16 drilling bore holes, particularly for ground temperature analysis, a numerical approach has been 17 considered for determining ground temperature. Furthermore, correlation charts between air and 18 ground temperatures have been developed as there were no proper studies on the ground temper-19 ature of Pakistan. Then, with the help of a boreholes drilled in National University of Sciences and 20 Technology Islamabad Pakistan, the actual ground and numerically calculated temperatures have 21 been compared which shows an error margin in the range between 0.27% for higher depths to 7.3% 22 near surface. Thus, it is shown that the proposed method is easy to implement and better than large 23 scale testing methods for the depths at which geothermal energy is extracted.

Estimating evapotranspiration at field scale is a major component of sustainable water management. Due to the difficulty to assess some major unknowns of the water cycle at that scale, including irrigation amounts, evapotranspiration is often computed as the residual of the instantaneous surface energy budget. One of the Surface Energy Bal-ance components with the largest uncertainties in their quantification over bare soils and sparse vegetation areas is the ground heat flux (G). Over the last decades, the es-timation of G with RS data has been mainly achieved with empirical equations, on the basis of the G and net radiation (Rn) ratio, G/Rn. G/Rn empirical equations generally require vegetation data (Type I empirical equations), in combination with surface tem-perature (Ts) and albedo (Type II empirical equations). In this article we aim to evalu-ate the estimation of G with RS. For the first time, we compare eight G/Rn empirical equations against two types of machine learning (ML) methods: an ensemble ML type, the Random Forest (RF), and the Neural Networks (NN). The comparison of each method is evaluated over dense dataset, including a wide range of climate and land covers, with data of Eddy-Covariance towers extended along the mid-latitude area that encompass the European and African continent. Our results have shown evidence that the driver of G in bare soils and sparse vegetation areas (Fraction of Vegetation, Fv <= 0.25) is Ts, instead of vegetation greenness indexes. On the other hand, the estimation of G with Rn, Ts or Fv decreases at dense vegetation areas (Fv >= 0.50). There are not significant differences between the most accurate type I and II empirical equations. For bare soils and sparse vegetation areas the empirical equation that better estimates G is E8, which combines the Leaf Area Index (LAI) and Ts. In dense vegetation areas (Fv >= 0.25), an exponential empirical equation based on Fv (E4), shows the best performance. However, ML better estimates G than the empirical equations, independently of the Fv ranges. A RF model with Rn, LAI and Ts as predictor variables shows the best accuracy and performance metrics, outperforming the NN model.

This study addresses an alternative use of viscous dampers (VDs) associated with buckling restrained braces (BRBs) as the innovative seismic protection devices. For this, 4, 8 and 12 storey steel frames were designed with 6.5 m equal span length and 4 m storey height. Thereafter, the VDs and BRBs were placed over the height of each frame considering three different configurations. The structures were modeled using SAP2000 finite element program and evaluated by the nonlinear time history analyses subjected to the six natural accelerograms (1976 Gazlı, 1978 Tabas, 1987 Superstition Hills, 1992 Cape Mendocino, 1994 Northridge and 1999 Chi-Chi). The structural response of the structures with and without VDs and BRBs were studied in terms of variation in the displacement, interstorey drift, absolute acceleration, maximum base shear, time history of roof displacement. The results clearly indicated that the application of VDs and BRBs had remarkable improvement in the earthquake performance of the case study frames by reducing the local/global deformations in the main structural systems and satisfied the serviceability.

Terrestrial laser scanning (TLS) has been adopted as a feasible technique to digitize trees and forest stands, providing accurate information on tree and forest structural attributes. However, there is limited understanding on how a variety of forest structural changes can be quantified using TLS in boreal forest conditions. In this study, we assessed the accuracy and feasibility of TLS in quantifying changes in the structure of boreal forests. We collected TLS data and field reference from 37 sample plots in 2014 (T1) and 2019 (T2). Tree stems typically have planar, vertical, and cylindrical characteristics in a point cloud, and thus we applied surface normal filtering, point cloud clustering, and RANSAC-cylinder filtering to identify these geometries and to characterize trees and forest stands at both time points. The results strengthened the existing knowledge that TLS has the capacity to characterize trees and forest stands in space and showed that TLS could characterize structural changes in time in boreal forest conditions. Root-mean-square-errors (RMSEs) in the estimates for changes in the tree attributes were 0.99-1.22 cm for diameter at breast height (Δdbh), 44.14-55.49 cm2 for basal area (Δg), and 1.91-4.85 m for tree height (Δh). In general, tree attributes were estimated more accurately for Scots pine trees, followed by Norway spruce and broadleaved trees. At the forest stand level, an RMSE of 0.60-1.13 cm was recorded for changes in basal area-weighted mean diameter (ΔDg), 0.81-2.26 m for changes in basal area-weighted mean height (ΔHg), 1.40-2.34 m2/ha for changes in mean basal area (ΔG), and 74-193 n/ha for changes in the number of trees per hectare (ΔTPH). The plot-level accuracy was higher in Scots pine-dominated sample plots than in Norway spruce-dominated and mixed-species sample plots. TLS-derived tree and forest structural attributes at time points T1 and T2 differed significantly from each other (p < 0.05). If there was an increase or decrease in dbh, g, h, height of the crown base, crown ratio, Dg, Hg, or G recorded in the field, a similar outcome was achieved by using TLS. Our results provided new information on the feasibility of TLS for the purposes of forest ecosystem growth monitoring.

The generation of high-quality wideband frequency sweeps presents a significant challenge, particularly in modern telecommunication, radar, and measurement systems where miniaturization is paramount. While phase-locked loops (PLLs) have become the dominant technique for signal generation, their application in broadband sweeps necessitates fractional-N operation. This, in turn, degrades phase noise and introduces unwanted spurs. This paper proposes a novel approach for broadband signal generation. By cascading two PLLs and utilizing a coaxial resonator, we achieve a high-performance oscillator that operates without the excessive fractional spurs, maintaining their level below -80 dBc across the entire frequency band. The prototype demonstrates non-degraded phase noise performance, reaching -102 dBc/Hz at 100 kHz offset and -121 dBc/Hz at 1 MHz offset for signal at 10 GHz. Despite significant frequency jumps, our design achieves lock times below 41 µs. These results, supported by theoretical analysis, validate the proposed method's effectiveness in generating low-noise broadband frequency sweeps, ideal for local oscillator applications.

In this paper, the Phase-Scheduled-Command FXLMS algorithm with the phase error between the disturbance and command signal is analyzed in detail. The influence of the phase error on the convergence time constant, convergence rate, and performance of convergence is explained for both stationary and nonstationary disturbance signals case. For stationary disturbance, the phase error slightly increases the convergence rate but heavily increases the distance of the optimum vector from the initial value, leading to poor convergence time constant performance. For nonstationary disturbance, the existence of phase error leads to poor convergence performance in every step, resulting in poor sound profiling performance. And the estimation of the phase error influence is developed in the closed form. Simulations are performed to demonstrate the validity of the analysis results.

Linear state estimation (SE) formulation under a rectangular coordinate system has been proved to be applicable for real-time distribution network management. Micro phasor measurements’ model can be accommodated into this kind of SE easily. However, voltage magnitude, active power and reactive power measurements are transformed to linear measurements with large node voltage error. To cope with this issue, a linear state estimation under a polar coordinate system is adopted at the first stage to obtain accurate enough complex node voltage, and then nonlinear measurements are transformed to be linear with complex node voltage. At the second stage, linear SE under a rectangular coordinate system can be adopted to satisfy more strict network constraints. The proposed two-stage linear SE is validated on balanced 14, 33, 70,84, 119, 135 nodes network and IEEE 13, 34, 37,123 unbalanced test feeders.

In the last decade, we have witnessed an upsurge in nuclei-based studies, particularly coupled with next-generation sequencing. Such studies aim at understanding the molecular states that exist in heterogeneous cell populations by applying increasingly more affordable sequencing approaches, in addition to optimized methodologies developed to isolate and select nuclei. Although these powerful new methods promise unprecedented insights, it is important to understand and critically consider the associated challenges. Here, we provide a comprehensive overview of the rise of nuclei-based studies and elaborate on their advantages and disadvantages. Improved designs and appropriate use of the various experimental strategies will result in acquiring biologically accurate and meaningful information.

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

Corresponding to the principles of biological synapses, an essential prerequisite for hardware neural networks using electronics devices is continuous regulation of conductance. We implemented artificial synaptic characteristics in a (GeTe/Sb2Te3)16 iPCM with a superlattice structure under optimized identical pulse trains. Based on atomically controlling the Ge switch in the phase transition that appears in the GeTe/Sb2Te3 superlattice structure, multiple conductance states were implemented by applying the appropriate electrical pulses. Furthermore, we found that the bidirectional switching behavior of a (GeTe/Sb2Te3)16 iPCM can achieve a desired resistance level using the pulse width. Therefore, we also fabricated a Ge2Sb2Te5 PCM and designed a pulse scheme based on the phase transition mechanism to compare to the (GeTe/Sb2Te3)16 iPCM. We designed an identical pulse scheme that implements linear and symmetrical LTP and LTD based on the iPCM mechanism. As a result, the (GeTe/Sb2Te3)16 iPCM showed relatively excellent synaptic characteristics by implementing gradual conductance modulation, a nonlinearity value of 0.32, and LTP/LTD 40 conductance states using identical pulses trains. Our results demonstrate the general applicability of the artificial synaptic device for potential use in neuro-inspired computing and next generation non-volatile memory.

In this paper, the deformation and phase transformation of disorder α phase at (α + γ) two phase region in as-forged Ti-44Al-8Nb-(W, B, Y) alloy are investigated by hot compression and hot packed rolling. Detailed microstructural evolution demonstrates that the as-deformed microstructure is significantly affected by deformation conditions. The mircrostructure differences are mainly due to temperature drop and strain rate. The evolution of α lamelae into α grains is detailed descripted. Moreover, the disorder α lamellae can also be decomposed into some new α grains by the assisted decomposition mechanism of γ grains. Microstructure evolution model of current TiAl alloy at 1250 °C during hot rolling is built.

The evolving multiphase induction generators (MPIG) with more than three phases are receiving prominence in high power generation systems. This paper aims at the development of a comprehensive model of the wind turbine driven seven-phase induction generator (7PIG) along with necessary the power electronic converters and controller for grid interface. The dynamic model of the system is developed in Maltlab/Simulink. Synchronous reference frame phase-locked loop (SRFPLL) system is incorporated for grid synchronization. The modeling aspects are detailed and the system response is observed for various wind velocities. The effectiveness of seven phase induction generator is demonstrated with the fault tolerant capability and high output power with reduced phase current when compared to conventional 3-phase wind generation scheme. The response of the PLL is analyzed and the results are presented.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

This study aims to evaluate the combined assimilation of AGRI infrared radiance and ground-based MWR (Microwave Radiometer) data for predicting short-duration heavy rainfall. The WRFDA 4.3 framework is utilized to establish the data assimilation interface. The structural characteristics of this joint assimilation approach are analyzed using a typical heavy rainfall event in the Kaifeng region of Central China. The findings indicate the following: (1) The joint assimilation of FY-4A AGRI and ground-based MWR data effectively corrects the initial moisture content in model simulations. Data assimilation significantly improves the simulation of 24-hour accumulated rainfall. Furthermore, the joint assimilation of AGRI radiance and MWR data outperforms assimilating either of them individually; (2) In the heavy rainfall stage, from the low level to the high level, strong upward movement occurs in the center of the rainstorm. The water vapor in the process of this rainstorm mainly comes from the westward air transport in front of the high trough. The water vapor is continuously transported to the heavy rainfall belt through this channel, providing sufficient water vapor for the maintenance of the rainstorm; (3) The combination of the interaction between high and low level vorticity and divergence in the atmosphere and the vertical upward movement, the emergence of low level jet and the generation of unstable energy in the atmospheric environment jointly lead to the occurrence of the rainstorm process; and (4) The terrain-sensitive experiment results show that, the existence of the topography of Taihang Mountain changes the precipitation in Kaifeng area, and reducing the terrain height will lead to a 50%-60% decrease in the overall precipitation of the precipitation center, and the precipitation range will also be greatly reduced. An increase of more than 50% in terrain height will lead to an increase in precipitation center, precipitation range and precipitation intensity, and an increase of 10%-20% in overall precipitation; An increase of more than 75% in the terrain height will cause the rain belt to shift eastward by about 0.5°E, and the precipitation center will shift significantly eastward. When the terrain height increased by more than 100%, the precipitation did not continue to increase, which was basically the same as the control test. This paper provides a valuable basis for further improving the application of FY-4A AGRI radiance and ground-based microwave radiometer in numerical weather models.

In order to alleviate the conflict between populations and land-resource, Tianjin has adopted multi-phase reclamation projects to formed large-scale artificial reclamation land. However, the reclamation areas are susceptible to subsidence, which demonstrate a serious threat to infrastructure and people’s lives and property. The SBAS-InSAR was used to acquired surface deformation of Tianjin Binhai New Area from January 2017 year to December 2022 year, analyzed in depth the response relationship between land subsidence and reclamation projects time as well as the land use type. The results show that the Lingang Industrial Zone was the earliest to be reclaimed, with extensive reclamation completed by 2016 year, while Nangang Industrial Zone and Hangu Port started reclamation projects in 2009 year, some areas are still currently under construction. There is a strong correlation between surface deformation and reclamation time, the severe land subsidence occurred over newly reclaimed areas. Surface deformation gradually intensifies from west to east, the maximum surface settlement in Nangang Industrial Zone, Lingang Industrial Zone from the west to the east has changed from -50 mm to -890 mm,45 mm to -580 mm, respectively, reclamation area of Hangu Port with maximum surface deformation is -250 mm. Significant differences deformation among different land use types, which reclamation projects completed in the same time. Subsidence is positively correlated with surface load, in areas with higher surface loads, the surface settlement is also severer,the average surface settlement for the heavy shipyard, 67 grain storage tanks, 27 grain storage tanks, road, and bare land are -201 mm, -166 mm, -107 mm, -64 mm, and -43 mm, respectively. This study reveals significant differences of surface deformation in the reclamation completed at different times and the load is the main driving factor of settlement difference in the reclamation land completed at the same time. Which has important guiding significance for preventing and controlling geological disasters in the reclamation area and later development planning.

Recycled tire fibers (RTF) are currently one of the most abundant waste not being recovered due to several processing hurdles and the presence of high amounts of residual ground rubber particles (GR). Therefore, this study proposes a simple approach to separate most of rubber particles from fibers and to determine their rubber content using thermogravimetric analysis (TGA)/calcination. Afterwards, clean fiber (CF) and GR are used as fillers for recycled post-consumer low density polyethylene (rLDPE), and their effects on the physical properties are investigated. Accordingly, a series of composites with CF and GR is prepared at different filler concentrations (0-30%) via extrusion compounding before using compression molding and injection molding for comparison. In all cases, injection molding leads to higher strength and modulus, but lower elongation at break. The results show that incorporating 30 wt.% of CF into rLDPE yields a remarkable improvement in tensile strength (15%), tensile modulus (192%) and flexural modulus (142%). On the other hand, the incorporation of up to 30 wt.% of GR results in a reduction of both tensile strength and flexural modulus by 15%, confirming the critical role of the cleaning process for RTF in achieving the best results.

In order to study the surface settlement law of subway tunnel engineering site overlying soft soil layer under the action of earthquake, ABAQUS finite element analysis software was used to study the surface settlement law of subway tunnel construction site overlying soft soil layer under the action of three different seismic waves, including El-Centro wave, Kobe wave, and artificial seismic wave with exceedance probability of 10%, based on the Dalian Metro Line 5 with overlying soft soil layer as the engineering background, and the law was analyzed theoretically. Then, the surface settlement law of tunnel top was studied based on El-Centro wave and soft soil parameters, and the sensitivity analysis of soft soil parameters on surface settlement of tunnel top was carried out by orthogonal test method. The results show that under earthquake action, the settlement of the strata within a certain range of the tunnel roof is significantly greater than that of the surrounding strata, forming a settlement trough with a width of about 8 to 20 meters. The width of the settlement trough under the El-Centro wave is the largest, about 19.6 meters, surpassing the artificially synthesized seismic waves with a probability of 10%, which is about 15.6 meters, while the width of the settlement trough under the Kobe wave is the smallest, about 8.5 meters. The ground surface within a range of about 20 meters above the tunnel roof is most strongly affected by the seismic waves and the special lithology of the overlying soft soil layer, and the settlement is the largest. The settlement law of the settlement trough in the overlying strata of the tunnel conforms to the Peck formula. Increasing the elastic modulus of the silty soil can reduce the settlement of the ground surface above the tunnel roof, increasing the Poisson's ratio of the silty soil will increase the settlement of the ground surface above the tunnel roof, increasing the cohesive force of the silty soil to 20 kPa will basically stabilize the settlement of the ground surface above the tunnel roof, and increasing the internal friction angle of the silty soil will basically not change the settlement of the ground surface above the tunnel roof. The sensitivity of the soft soil parameters to the settlement of the ground surface above the tunnel roof is in the order of Poisson's ratio, elastic modulus, cohesive force, and internal friction angle.

A real-time flight simulation tool is proposed using a Virtual Reality Head-Mounted Display (VR-HMD) for airships operating in beyond the line-of-sight (BLOS) conditions. Particularly, the VR-HMD is developed for stratospheric airships flying at low/high altitudes. The proposed flight simulation tool uses the corresponding aerodynamics characteristics of the airship, the buoyancy effect, mass balance, added mass, propulsion contributions and ground reactions in the FlightGear Fight Simulator (FGFS). The VR headset has been connected to the FGFS along with the radio controller containing the real-time orientation/state of each button that is also simulated to provide better situational awareness and a Head-Up Display (HUD) that has been developed to provide the required flight data. In this work, a system was developed to connect the FGFS and the VR-capable graphics engine, Unity, to a PC and a wireless VR-HMD in real-time with minimal lag between data transmission. A balance was found for FGFS to write to a CSV file at a period of 0.01s. For Unity, the file was read every frame which translates to around 0.0167s (60 Hz). A test procedure was also conducted with a similar rating technique based on the NASA TLX questionnaire that identifies the pilot’s spare mental capacity when completing an assigned task to assure the comfortability of the proposed VR-HMD. Accordingly, a comparison has been made for the aircraft control using the desktop simulator and the VR-HMD tool. Results, showed that the current iteration of the system is ideal to train pilots on using similar systems in a safe and immersive environment. Furthermore, such an advanced portable system may even increase the situational awareness of pilots and allow them to complete a sizeable portion of actual flight tests with the same data transmission procedures in simulation. The resulting VR-HMD flight simulator is also conceived to express the ground control station (GCS) concept and transmit flight information as well as the point of view (POV) visuals in real-time using the real environment broadcasted using an onboard camera.

Accurately quantifying the above-ground volume (AGV) and thus above-ground biomass (AGB) of forest stands is an important aspect in the conservation of mangrove ecosystem owing to their ecological and economic benefits. However, the number of studies focusing on quantifying mangrove forests’ biomass has been relatively low due to their marshy terrain, making exploratory studies challenging. In recent times, the use of LiDAR technologies in forest inventory studies has become increasingly popular, due to the reliability of LiDAR as a highly accurate means of 3D spatial data acquisition. In this study, we propose an end-to-end methodology for estimating AGV of mangrove forest stands from terrestrial LiDAR data. Many of the recent studies on this topic effectively employ machine learning algorithms such as multi layer perceptron, random forests, etc. for filtering foliage in the point cloud data of single trees. This study further extends that approach by incorporating the impact of class imbalance of forest point cloud data in a weighted random forest classifier. For the task of segmentation of wood/foliage points in a single tree point cloud, this approach yielded an average increase of 2.737% in the balanced accuracy score, 0.007 in the Cohen’s kappa score, 2.745% in the ROC AUC score and 0.857% in the F1 score. For the task of AGV estimation of a single tree, this approach resulted in an average coefficient of determination of 0.93 with respect to the ground truth volumes. For the task of counting pneumatophores in a plot-level point cloud, the proposed breadth-first searching method yielded an average coefficient of determination of 0.9391. Also, the machine learning classifier and geometric features used in this study were invariant to tree species and hence could be generalised for the classification of point clouds of other tree species as well. Finally, a breadth-first graph-search segmentation based approach is also proposed as part of this pipeline to estimate the contribution of pneumatophores to the AGB of mangrove forest stands. Since pneumatophores are a special adaptation of mangrove forests for gaseous exchange in marshy environments, this study aims to incorporate the detection and AGB estimation of pneumatophores in the inventory of mangrove forest stands. Studying the contribution of pneumatophores to the AGB of mangrove forest plots could also aid future mangrove forest inventory studies in modeling the underlying root network and estimating the below-ground biomass of mangrove trees.

An increase in air temperature leads to a significant transformation of the relief and landscapes of the Arctic. The rate of permafrost degradation, posing a profound change in the Arctic landscape, depends on air temperature, vegetation cover, type of soils, surface and ground waters. The existing international circumpolar programs dedicated to monitoring the temperature state of permafrost TSP (Thermal State Permafrost) and active layer thickness CALM (Circumpolar Active Layer Monitoring) are not sufficient for a comprehensive characterization of geocryological conditions. Yet, no standardized protocol exists for permafrost monitoring and related processes. Here, we propose a novel multi-parameter monitoring protocol and implement for two sites in the European part of the Russian Arctic: the Yary site along the coast of the Baydaratskaya Bay in the Kara Sea (68.9°N) within the continuous permafrost area and the Hanovey site in the Komi Re-public (67.3°N) within the discontinuous permafrost one. The protocol includes drilling boreholes, determining the composition and properties (vegetation cover and soils), snow cover measure-ment, geophysical imaging, active layer estimation and continuous ground temperature meas-urements. Ground temperature measured in 2014 – 2020 revealed that amplitudes of surface tem-perature fluctuation had no significant difference between the Yary and Hanovey sites, while that the mean annual temperatures between the areas had a considerable difference of greater than 3.0 °C. The period of the presence of the active layer changed with the year (e.g., ranging between 135 and 174 days in the Yary site), showing longer when the air temperatures in summer and the preceding winter were higher. Electrical resistivity tomography (ERT) allowed determining the permafrost distribution and active layer thicknesses. Thermometry results were consistent with our geophysical data. Analyzing the composition and properties of frozen soils helped better interpret the data of geophysical and temperature measurements. Our work by integrating the study of the soil properties, ground temperatures, and ERT allowed fully characterize these sites, suggesting that it helps better understand the thermal state in any other research sites in the European north of Russia. Our suggested monitoring protocol enables calibrating and verifying the numerical and analytical models of the heat transfer through the earth’s surface.

Tephra plumes can cause a significant hazard for surrounding towns, infrastructure, and air traffic. The current work presents the use of a small and compact X-band Multi-Parameter (X-MP) radar for the remote tephra detection and tracking of two eruptive events at Merapi Volcano, Indonesia, in May and June 2018. Tephra detection was done by analysing the multiple parameters of radar: copolar correlation and reflectivity intensity. These parameters were used to cancel unwanted clutter and retrieve tephra properties, which are grain size and concentration. Real-time spatial and temporal forecasting of tephra dispersal was performed by applying an advection scheme (nowcasting) in the manner of Ensemble Prediction System (EPS). Cross-validation was done using field-survey data, radar observations, and Himawari-8 imagery. The nowcasting model computed both the displacement and growth and decaying rate of the plume based on the temporal changes in two-dimensional movement and tephra concentration, respectively. Our results with ground-based data, where the radar-based estimated grain size distribution fell within the range of in-situ data. The uncertainty of real-time forecasted tephra plume depends on the initial condition, which affects the growth-and decaying rate estimation. The EPS improves the predictability rate by reducing the number of missed and false forecasted events. Our findings and the method presented here are suitable for early warning of tephra fall hazard at the local scale.

The UNESCO World Heritage Hadrian’s Villa lies over the Colli Albani volcanic district near Rome. Magnetic, paleomagnetic, radar, and electric resistivity surveys were performed in the Plutonium–Inferi sector to detect buried buildings and outline a segment of the underground system of tunnels that link different zones of the villa. In particular, a paleomagnetic analysis of the bedrock unit allowed to accomplish an accurate geomagnetic field modelling and characterize the archaeological sources of the magnetic field anomalies. We used a computer-assisted forward modelling procedure to generate a structural model of the sources of the observed anomalies. The intrinsic ambiguity of the magnetic field modelling was reduced with the support of ground penetrating radar amplitude slices and an analysis of radar and electric resistivity profiles. The bedrock lithology in this area is an ignimbrite tuff characterized by abundant iron oxides. The high-amplitude magnetic anomalies observed in the Plutonium–Inferi area are due to strong bedrock remnant magnetization and susceptibility contrasts between topsoil infill of cavities and the surrounding tuff. The resulting magnetization model of the Plutonium–Inferi complex shows that the observed anomalies are mostly due to the presence of tunnels, skylights and a system of ditches excavated in the tuff.

Quality control (QC) may be a lengthy and tedious process. As a result, most data users use data from meteorological services without performing data quality checks. The South African Weather Service (SAWS) re-established the national solar radiometric network comprising of 13 new stations within the six climatic zones of the country. This study reports on the performance results of the Baseline Surface Radiation Network (BSRN) QC procedures applied to the solar radiation data within the SAWS radiometric network. The overall percentage performance of the SAWS solar radiation network based on BSRN QC methodology is 97.79%, 93.64%, 91.6% and 92.23% for Long Wave Downward Irradiance (LWD), Global Horizontal Irradiance (GHI), Diffuse Horizontal Irradiance (DHI) and Direct Normal Irradiance (DNI) respectively with operational problems largely dominating the percentage of bad data. The overall average performance of the Surface Solar Radiation Dataset – Heliosat (SARAH) data records for the GHI estimation for all the stations showed a Mean Bias Deviation (MBD) of -8.28 Wm^-2, a Mean Absolute Deviation (MAD) of 9.06 Wm^-2 and the Root Mean Square Deviation (RMSD) of 11.02 Wm^-2. The correlation (quantified by R²) between ground-based and SARAH-derived GHI time series was ~ 0.98. The established network has the potential of providing high quality minute solar radiation data sets (GHI, DHI, DNI and LWD) and auxiliary hourly meteorological parameters vital for scientific and practical applications in renewable energy technologies in South Africa.

Automobile proving ground is important for the research of vehicles which is used for the vehicle dynamics, durability testing, braking testing, etc. However, the roads in automobile proving ground will inevitably be damaged with the extension of the service life. In most previous researches, equipment similar to laser cross-section was used to detect pavement quality, the principle of which was to reflect pavement quality by detecting road surface roughness. This method ignores the elastic deformation of the roads itself when the vehicle is traveling on it and hardly compensate for the amendment. Therefore, this article presents a new method based on force sensor to reduce the impact of elastic deformation such as wheel tyre deformation, pavement deformation, and wheel rim deformation. In which, force sensors mounted on the wheels collect the three-dimensional dynamic load of the wheel.The presented method has been tested with two sets of cobblestone road load data, and the results show that The　incentives imposed by the test vehicle on the target road are 88.3%, 91.0%, and 92.05% of the incentives imposed by the test vehicle on the standard road in three dimensions, respectively. It is clear that the proposed method has strong potential effectiveness to be applied for lose detection of the special road application.

Propagation effects on the Narrow Bipolar Pulses (NBPs) or the radiation fields generated by compact cloud discharges as they propagate over finitely conducting ground are presented. The results are obtained using a sample of NBPs recorded with high time resolution from close thunderstorms in Sri Lanka. The results show that the peak amplitude and the temporal features such as the Full Width at Half Maximum (FWHM), zero crossing time and the time derivative of NBPs can be significantly distorted by propagation effects. For this reason the study of peak amplitudes and temporal features of NBPs and the remote sensing of current parameters of compact cloud discharges should be conducted using NBPs recorded under conditions where the propagation effects are minimal.

This paper deals with bistatic subsurface probing of a horizontally layered dielectric half-space by means of ultra-wideband electromagnetic pulses. A receiver collects reflections from the air-ground interface and from the gradients of dielectric permittivity in the half-space. This scenario is of interest for ground penetrating radar (GPR) applications. For the analytical description of the received signal, we developed and implemented a novel time-domain version of the coupled-wave Wentzel–Kramers–Brillouin approximation. Our solution is in very good agreement with finite-difference time-domain results, radically accelerates calculations, and effectively accounts for the protracted return signals observed in the lower part of the GPR spectrum. The paper includes results showing the application of the proposed technique to two case studies: in particular, the method was employed for the post-processing of experimental radargrams collected on Lake Chebarkul, in Russia, and to simulate GPR probing of the Moon surface, to detect smooth gradients of the dielectric permittivity in lunar regolith.

Soil-structure interaction (SSI) could affect the seismic response of structures. Since liquid storage tanks are vital structures and must continue their operation under severe earthquakes, their seismic behavior should be studied. Accordingly, the seismic response of liquid storage tanks founded on half space soil is scrutinized under different earthquake ground motions. To better comparison, the six considered ground motions are classified based on their pulse like characteristics, into two groups, named far and near fault ground motions. To model the liquid storage tanks, the simplified mass-spring model is used and the liquid is modeled as two lumped masses known as sloshing and impulsive, and the interaction of fluid and structure is considered using two coupled springs and dashpots. The SSI effect, also, is considered using a coupled spring and dashpot. Besides, four types of soils are used to consider wide variety of soil properties. To this end, after deriving the equations of motion, the MATLAB programming is employed to obtain the time history responses. Results show that although the SSI effect leads to decrease the impulsive displacement, overturning moment and normalized base shear, the sloshing (or convective) displacement is not affected by such effects due to its long period.

The research examines the relationship between self-rated health situation and personal percep-tion of heat waves, and how social linkage of communities would be a moderator variable in residents’ perception of heat waves in Taiwan. This study uses the questionnaire conducted by Sinica “Responsive Capacity under Heat Wave: The Perspectives of the Locals”(2019), using OLS method for estimating the unknown parameters in multiple regression model. The author finds that the correlation of self-rated health situation and perception toward heat is significantly posi-tive. Also, social linkage in communities affects strongly as a moderator variable: While the sat-isfaction to with their community could reduce negative reaction to heat, contacts with neighbors could increase possibility people feel uncomfortable in high-temperature situation. This study ex-hibits the effects of social environment on community, and expects further related researches or practices to strengthen capability to resist heat wavesƒ for Taiwanese residents.

Amebiasis is a disease caused by the unicellular parasite Entamoeba histolytica. In most cases, the infection is asymptomatic but when symptomatic, the infection can cause dysentery and invasive extraintestinal complications. In the gut, E.histolytica feeds on bacteria. Increasing evidences support the role of the gut microbiota in the development of the disease. In this review we will discuss the consequences of E.histolytica infection on the gut microbiota. We will also discuss new evidences about the role of the gut microbiota in regulating the resistance of the parasite to oxi-dative stress and its virulence.