Involving industrial waste into economic circulation, in particular flotation waste from coal enrichment, is an urgent task. The coal preparation waste of ArcelorMittal Temirtau JSC was studied with a view to the possibility of using it as an alternative substitute for coke breeze in the sintering process. During a thermoanalytical study on a synchronous thermal analyzer STA 449 NETZSCH in dynamic mode with a heating rate of 10, 20, 30 °C/min in an air flow of 30 cm³/min in the temperature range 30–1000 °C, we determined the lower heat of combustion of carbon-containing material, change mass during calcination, change and rate of change in the mass of the sample, thermal effect of the process, the temperature of the beginning, end and maximum development of thermal effects. It has been established that the greatest mass loss is observed in the temperature range 580 °C- 610 °C, which is about 65–67% of the total mass of the organic component of coal. The maximum burnout rate corresponds to a temperature of 540–563 °C. The lowest calorific value of the studied waste was 15.9 MJ/kg. The results of thermal analytical research and technical analysis substantiate the possibility of using flotation waste in a mixture of up to 10% with coke breeze for combustion in the sintering layer for the production of sinter. Analysis of the composition of flotation waste showed that they have a high specific surface area (56.8∙10³ m²/kg), are highly dispersible, soggy, and capable of swelling, and the predominant amount of clay substance makes them a plastic material. The possibilities of using coal flotation waste as an alternative substitute for coke breeze have been studied after the regimes of its preparation for sintering have been developed and a rational regime of layer-by-layer combustion in the sintering layer has been established. The optimal ratio of coke and OPC in the fuel mixture of the sintering charge was determined.

In this work various sample of primary aluminum dross were investigated for composition and evaluation of hydrogen generation via hydrolysis in low concentration alkali solution. Composi-tion revealed low to moderate aluminium content and hydrolysis reactions showed low hydrogen generation volumes per sample mass as well as purity, where composition plays substantial role in the hydrogen evolution, yet showing that there is possible place for dross use in hydrogen generation. It was revealed that some dross samples in addition to hydrogen also release methane via hydrolysis. Rection rate was obtained by the shrinking core model, written for spherical solid particles. Sample composition on hydrogen generation volume is compared to known literature.

On the basis of a stocktaking on PVC in Europe and on a current ECHA investigation report, we conclude that regulatory action at EU level is recommended. We support ECHA's regulatory proposals in the main, but come to a more comprehensive proposal for the phasing-out of PVC beyond the area of electrical installations. PVC stored in buildings and infrastructure to date amounts to around 160 million tonnes ("stock") and this mass is still increasing. Parts from the stock have entered the waste management sector for years and their mass is gradually increasing. Neither material, chemical nor energy recovery will be able to absorb these incoming quantities. We therefore come to the conclusion that PVC should be collected separately and disposed of in an infrastructure designed for chlorine recovery. The required infrastructure should be set up and operated by the chemical industry. So, PVC will lose its status as a particularly economically favorable plastic. In view of the constantly increasing stock, we recommend phasing-out the production of virgin PVC as early as possible. In our opinion, this would also be justifiable because the effects of the closed loop recycling announced by VinylPlus ('Vinyl') would go in the same direction.

Scientists can use the Clustered regularly interspaced short palindromic repeats (CRISPR)/CRISPR-associated (Cas) protein 9 system, which is a powerful and flexible tool for changing the genome, to change only certain parts of the genome. This has helped researchers figure out how target genes work in biology and disease. CRISPR/Cas9 is made up of a sequence-specific CRISPR RNA (crRNA) set and a generic Cas9 nuclease. The crRNA set tells Cas9 where to cut DNA and cause double-strand breaks. In the next step of cellular DNA repair, insertions, deletions, and swaps are made at specific spots. For CRISPR/Cas9-mediated DNA cleavage to be specific, the target sequences must match the crRNA, and a protospacer nearby motif must be placed after the target sequences. In this article, we talk about how CRISPR/Cas9 works at the molecular level, what it can be used for, what it can't do, and what its future clinical treatment promise might be.

The European Green Deal poses a two-pronged challenge for the automotive industry: migrating to solutions based in light structures, requiring light weight concepts and light materials, while at the same time avoiding dependence towards the importation of these advanced materials. Aluminium alloys are lightweight and cost-effective materials that can successfully cover the requirements of many structural applications, however their production requires from bauxite and other Critical Raw Materials (CRM), such as Si and Mg. Aluminium alloys are fully recyclable, but scrap is usually contaminated and its use is related to an increment of impurities, tramp element and undesired inclusions. Traditionally, the use of secondary alloys has been restricted to low performance applications. The present work analyses the effect that the use of scrap has in the quantity of inclusions present in the alloy and in other properties relevant for the material processing. The study was carried out for common alloys belonging to 3 of the most common aluminium processes used in the car manufacturing industry: High Pressure Die Casting (HPDC) (EN AC-43500), extrusion (6063) and sheet metal forming (5754 and 6181). Reference alloy were mixed with different level of scrap (0, 20, 40, 60, 80 and 100%) trying to keep the chemical composition as unaffected as possible. The inclusions level of the alloy was characterized with the Prefil Foot-printer® test. In addition, the obtained materials, after being cast in an open mould, were subjected to metallographic characterization. Relevant properties to assess the formability quality of the alloys for the corresponding transforming process, were obtained: flowability test for HPDC alloy and high temperature compression for extrusion alloys. The results obtained suggest that the number of inclusions present in the melt highly increase with the amount of scrap used to produce the alloy. These inclusions are also related with an important lost of flowability, but do not have a noticeable impact on microstructure.

This study presents an innovative approach for the utilization of industrial by-products and municipal waste in the production of sustainable and environmentally friendly cement mortar. We explored stabilized stainless-steel reduced slag (SSRS) and polyethylene (PE) plastic waste as partial replacements for aggregates. Various engineering properties of the resulting cement mortar specimens, including slump, slump flow, compressive strength, flexural strength, tensile strength, water absorption, and ultrasonic pulse velocity (UPV), were investigated through comprehensive experimental tests. The influence of different water-cement (w/c) ratios and substitution amounts on the engineering properties of the cement mortar samples was thoroughly examined. The findings revealed that an increase in PE substitution adversely affected the overall workability of the cement mortar mixtures, whereas an increase in SSRS amount contributed to enhanced workability. As for the hardened properties, a consistent trend was observed for both cases, with higher w/c ratios and substitution amounts leading to reduced mechanical properties. Water absorption and UPV test results validated the increased formation of porosity with higher w/c ratios and substitution amounts. This study proposes a promising method to effectively repurpose industrial by-products and municipal wastes, transforming them into sustainable construction and building materials. Additionally, a comparative analysis of transportation costs and carbon footprint emissions between SSRS-cement mortar and PE-cement mortar was conducted to assess their environmental impact and sustainability. Generally, higher w/c ratios and replacement levels corresponded to reduced carbon footprint. The geographical location of the source of SSRS and PE remains a challenge and studies to overcome this challenge must be further explored.

India has pledged ambitious initiatives to mitigate its growing economies’ impact on the climate, including a goal of net zero emissions by 2070. The transportation sector is one of the key sources of emissions. Therefore, fostering e-mobility within this sector is a key priority for the Indian government. The lifecycle of LiBs raises numerous concerns regarding its sustainability in production, use of rare materials, and most importantly waste management. Furthermore, this paper will highlight the case for EV battery recycling as a growing sector that also has the potential to foster circularity in the EV sector. Through the introductory section, this paper lays out rationale for battery recycling in a circular EV economy. The subsequent sections discuss the current and emerging battery technologies and their link to recycling methods whilst overviewing domestic and foreign battery recycling companies. Finally, the paper concludes with a gap assessment of the battery recycling ecosystem in India and makes recommendations to further integrate this industry into the EV supply chain. As India steers towards a sustainable future, it is imperative that the country integrates battery recycling to enhance circularity in the EV ecosystem, closing the gap between a growing number of EVs and waste management.

Recent research has specifically targeted the decision-making process of eco-friendly individuals, emphasizing the significance of recycling and its impact on sustainability. Our study extends this inquiry by examining the correlation between recycling participation and pro-environmental behavior among consumers, integrating the concepts of self-efficacy, feelings of pride, and social pressure into our analysis. Utilizing Partial Least Squares-Structural Equation Modeling (PLS-SEM), we aimed to explore the intricate relationships that underpin these behaviors. Results suggest that self-efficacy and feelings of pride significantly influence individuals' recycling behaviors, highlighting the role of psychological and social factors in promoting environmental sustainability. Interestingly, it was concluded that social pressure did not have the expected moderating effect on increasing consumers' feelings of pride and self-efficacy toward recycling activities.This study not only sheds light on the underlying mechanisms that drive pro-environmental actions but also contributes to understanding sustainability promotion through recycling and offers insights for policymakers and environmental advocates to foster environmental responsibility and behavior change.

Geopolymer concrete (GPC) represents an innovative green and low-carbon construction material, offering a viable alternative to ordinary Portland cement concrete in building applications. However, existing studies tend to overlook the recyclability aspect of GPC for future use. Various structural applications necessitate the use of concrete with distinct strength characteristics. The recyclability of the parent concrete is influenced by these varying strengths. This study examined the recycling potential of GPC across a spectrum of strength grades (40, 60, 80 and 100 MPa, marked as C40, C60, C80 and C100) when subjected to freeze-thaw conditions. The cementitious material comprised 60% metakaolin and 40% slag, with natural gravel serving as the coarse aggregate, and the alkali activator consisting of sodium hydroxide solution and sodium silicate solution. The strength of the GPC was modulated by altering the Na/Al ratio. After 350 freeze-thaw cycles, the GPC specimens underwent crushing, washing, and sieving to produce recycled geopolymer aggregates (RGAs). Subsequently, their physical properties and microstructure were thoroughly examined. The findings indicated that GPC with strength grades of C100, C80, and C60 were capable of enduring 350 freeze-thaw cycles, in contrast to C40, which did not withstand these conditions. RGAs derived from GPC of strength grades C100 and C80 complied with the criteria for Class II recycled aggregates, whereas RGAs produced from GPC of strength grade C60 aligned with the Class III level. A higher strength grade in the parent concrete correlated with enhanced performance characteristics in the resulting recycled aggregates.

Sustainable supply chain management (SSCM) represents a critical strategy for the electronics industry to balance economic objectives with environmental and social responsibility across complex global production networks. This multiple case study analysis investigates SSCM integration within leading Korean electronics manufacturers Samsung, LG, and Hyundai. In-depth qualitative data, focus groups, and sustainability report analysis reveals the policies, practices, results and implementation barriers related to incorporating sustainability criteria across procurement, manufacturing, distribution and recycling functions. Findings show sustainability considerations increasingly driven by cost, risk, reputational and regulatory factors, with vertical coordination initiatives helping transfer knowledge to assist suppliers on compliance and emissions reductions. Yet substantial obstacles persist around monitoring, coordination, transparency and technical capabilities, especially amongst lower tiers. The paper discusses how common reporting standards, ethical sourcing certification and partnerships can accelerate electronics supply chain sustainability. By mapping integration achievements and gaps, this study informs managerial best practices and policy reforms toward promoting socially and ecologically responsible models for Korea's vital export industry as it navigates rising stakeholder pressures.

The consistent and continuous growth in the world’s population is creating many challenges for public policymakers in the different life areas, including dealing with the increasing amounts of waste that are generating problems involving air and land pollution and a shortage of land for waste disposal. This study presents the results of public policy on managing municipal waste, as manifested in the quantity and rate of waste collected throughout Israel in recent years and disposed of in the various landfills and in analysis of the political and economic factors affecting this policy. The study combines a quantitative and qualitative approach, where the quantitative study includes analysis of statistical data based on information from the Central Bureau of Statistics, the Ministry of Environmental Protection, the Ministry of Finance, and others, and the qualitative study relies on reading and analyzing primary documents of the different government ministries on Israel’s waste disposal policy and information in the media on this issue. The research findings attest to an increase in the amount of municipal waste dumped in Israel, a merely slight decrease in the rate of landfilling as a proportion of all municipal waste disposal, and a merely slight increase in the rate of municipal waste recycled in recent years. The research conclusions stress the effects of the landfill levy and the Cleanliness Maintenance Fund on one hand, and of the government instability in the Ministry of Environmental Protection, the positivist policy embraced by decision makers in the Ministry of Environmental Protection, and the power struggles between Israel’s different ministries on the other, as the respective economic and political factors affecting Israeli policy on municipal waste management.

Composites, and especially carbon fiber reinforced plastics (CFRPs), are increasingly used in the automotive, aerospace, and aviation industries, and as a result, CFRP production has increased dramatically, leading to a corresponding increase of waste. Landfill and incineration of waste are likely to be restricted as a result of the legislation, thus highlighting the need for efficient recycling methods for CFRPs. However, the recycling of CFRP is very challenging, mainly due to the difficulty of removing the thermosetting matrix. This study reports a pre-screening of the solvolysis recycling process for CFRPs based on the mechanical properties of the recovered fibers. To this end, solvolysis tests were conducted on unidirectional CFRP samples under supercritical and subcritical conditions using acetone and water. The solvolysis tests were conducted for various conditions of temperature, pressure, and reaction time. The efficiency of the recycling processes has been evaluated through a morphological and a mechanical characterization of the recovered fibers. In most cases, the decomposition efficiency of the epoxy resin, measured in terms of mass, ranged between 90 and 100%. Moreover, the scanning electron microscopy images of the recovered fibers showed negligible traces of resin residues and no detectable signs of physical damage or any changes in morphology with regard to diameter. Finally, the single-fiber tension tests revealed that that the recovered fibers retained more than 61% of their initial Young's modulus and 70% of their tensile strength.

The purpose of this study is to assess the solid waste management status and practice in Sendafa town, Oromia regional state residents. In order to achieve this goal, the researcher intends to employ both primary and secondary data from the Sendafa town municipality. With the aid of multi-cluster sampling and a purposive sampling method, the researchers chose a sample size of 398 people and 10 interview responders. To utilize a systematic sampling technique at intervals of residences, individual samples were chosen. Quantitative data was cleaned and analysed using STATA software. A multiple linear regression model and logistic regression other descriptive statistics methods were then used to change the results. The qualitative data were imported, coded, and thematised using ATLAS.ti.9 in order to prepare respondents' interviews for analysis. The findings indicate that residents' poor solid waste management practices are a result of a lack of awareness, low family income transportation issues, issues with waste collectors, a lack of a sense of responsibility and belonging, and a failure to enforce current solid waste management laws. Solid waste accumulates near roads, bridges, and residential areas that are close to landfills, contaminating the area and leading to diseases like TB and Asthma (and other related health issues in children and adults who live there). Thus, researcher recommends that to have sustainable solid waste management the town administrators should have plan to develop awareness creation symposium or panel of discussion, resolve transportation issues, monitor and guide the routine activities of waste collectors, develop sense of belongingness for themselves and for the community, develop integrated solid waste land fill projects and working with all stakeholders like NGO and health institution will minimize the adverse effect of improper solid waste management. Keywords: Solid Waste, Status of Solid Waste Management, Land fill site suitability

Hong Kong is the biggest consumer of eggs in the world and ranks on the top with an average consumption of 24.52kg/capita/year. The egg consumption trend in Hong Kong has been increasing specifically; a drastic increase of about 100% has been observed from 2008 to 2020. One of the reasons behind this significant increase is the increase in the gross national income of Hong Kong in addition to the population growth rate. However, there was a slight decline in egg consumption trend in the year 2020 amid the COVID-19 pandemic. It has been estimated that there was a bulk of 17,100 tons of recoverable waste eggshells in 2019 (pre-COVID-19 situation), having a daily yield of 47 tons per day. Based on the linear regression, it may be expected that if the pre-COVID-19 trend of egg consumption remains sustained, there will be a big bulk of more than 45,000 tons per year and up to 125 tons per day of waste eggshells till 2050. In addition, a public survey was conducted across the city targeting individuals, families, and restaurants majorly on egg consumption and reuse. The survey outcomes revealed that Chinese eggs have an extensive market in Hong Kong, and people have a positive attitude towards eggshell recycling. Also, a massive population disposes of the waste eggshells while only a trace population reuses them. Therefore, Hong Kong has a very high potential to improve the circular economy by reusing waste eggshells on a commercial level in cementitious products.

In "genome editing," a type of genetic engineering, DNA is added, taken away, or changed in an organism's genome. Biomedicine, biotechnology, and synthetic biology, just to name a few, have all gained a lot from how often this method is used. Before the editing process can start, a Double-Strand Breaks (DSB) must be made in the DNA at a specific gene. Researchers have made nucleases, which are sometimes called "molecular scissors," to fix this DSB. Transcription activator-like effector nucleases (TALENs), Zinc-finger nucleases (ZFNs), and homing endonucleases are all examples of protein targets that have been studied and changed. The last part gave an overview of these study projects and explained how to make Cas12a for specific uses. The applications of Cas12a have been extensively studied in recent years, but the protein still holds a lot of promise as a treatment and screening tool. In order to give a quick review of CRISPR-Cas12a and its uses, we will briefly talk about the structure and function of the different parts of the reaction pathway that lead up to the catalysis of the target DNA. Cas12a uses a multistep process to make sure that it is selecting the right DNA. This is a good trait for a device that changes the DNA because it makes it less likely that something bad will happen. Even though data shows that a new CRISPR RNAs (crRNA) molecule can stop Cas12a from randomly destroying ssDNA, it may still hurt the host cell while trying to change the genome. The action of Cas12a catalysis, which is a powerful tool for changing the genome, needs to be changed so that it can be more easily controlled and managed. Using what we know about how Cas12a works, we have made mutants that are less active on ssDNA and more active on dsDNA. So far, only Cas9 and Cas12a, which are both part of the CRISPR family, have been used to change the genome. Because of how similar and different these two endonucleases are, CRISPR can now be used for multiple scientific purposes. Cas12a is better than Cas9 because it makes double-strand breaks (DSBs) that favor Homology-Directed Repair (HDR) over Non-homologous end joining (NHEJ) and can change more than one copy of the genome at the same time. Both Cas9 and Cas12a are being changed to make them better at detecting Protospacer Adjacent Motif (PAM) than they are in their natural state. This will make it possible to start focusing on more genes.

With the proliferation of electric vehicles (EVs) and the consequential increase in EV battery circulation, the need for accurate assessment of battery health and remaining useful life (RUL) is paramount, driven by environmentally friendly and sustainability goals. This study addresses this pressing concern by employing data-driven methods, specifically harnessing deep learning techniques to enhance RUL estimation for lithium-ion batteries (LIB). Leveraging the Toyota Research Institute Dataset, consisting of 124 lithium-ion batteries cycled to failure and encompassing key metrics such as capacity, temperature, resistance, and discharge time, our analysis substantially improves RUL prediction accuracy. Notably, the Convolutional-LSTM-Deep Neural Network (CLDNN) model and the Transformer-LSTM (Temporal-Transformer) model have emerged as standout Remaining Useful Life (RUL) predictors. The CLDNN model, in particular, achieved a remarkable Mean Absolute Error (MAE) of 84.012 and a Mean Absolute Percentage Error (MAPE) of 25.676. Similarly, the Temporal-Transformer model exhibited notable performance with an MAE of 85.134 and a MAPE of 28.7932. These impressive results were achieved through the application of Bayesian hyperparameter optimization, further enhancing the accuracy of predictive methods. These models were benchmarked against existing approaches, demonstrating superior results with an improvement in MAPE ranging from 4.01% to 7.12%.

Clothing consumers mostly purchase, use, and dispose of clothing products in a linear business model. This approach pollutes the environment and causes economic and social crises in the ecosystems. This study evaluates the amount of generated postconsumer clothing waste (PCCW) and proposes recycling as a sustainable waste management approach. Data were collected to understand disposal behavior of consumers with 474 respondents selected from households in Bahir Dar city. The findings show that all the determinant factors on the PCCW generation level except religion were significant. The most frequently disposed type of clothing waste is jeans-trouser (51%). The CEBM was used to develop alternative products from a jeans-based clothing waste. The jean's fiber and fabric-reinforced composite materials were developed using unsaturated polyester resin as a sustainable way of PCCW management strategy. The shredded form fiber-reinforced composite was found to have a smoother surface than that of the chopped or cut fabric-reinforced composite. The product was characterized by physical and mechanical properties. The study can be further extended to the scope of the entire consumers in Ethiopia and alternative recyclable products can be studied.

The circular supply chain was applied to many industries in the past studies, whereas the rubber recycling industry has not been explored in detail yet. Therefore, this study indentified the key factors of the circular supply chain used in remanufactured products, thereby perfecting its framework. This study put forward 5 aspects and 19 criteria for reference, so that companies in the rubber recycling industry are able to clearly know the direction of implementation when con-structing the circular supply chain for remanufactured products. This study integrated expert opinions with the fuzzy Delphi method and the fuzzy decision making trial and evaluation laboratory proposed key factors, and performed the ranking of importance. The results have displayed that key aspects include the circular business model (A3), increasing the value of resources in the supply chain (A4), and risk management of the circular supply chain (A2). The factors that the rubber recycling industry needs to pay attention to are: optimizing the production process (C2), sharing data in the product lifecycle (C4), effectively tracking and recycling products (C5), redesigning remanufactured products (C13), enhancing resource efficiency (C16), and identifying waste composition and separating materials (C14) . Based on the abovementioned, we had a discussion in this study.

Recent development for synthesis of bio-based long chain aliphatic polyesters by acyclic diene metathesis (ADMET) polymerization of α,ω-dienes, derived from plant oils and bio-based chemicals, like bis(10-undecenoate) with isosorbide, using ruthenium-carbene catalysts have been reviewed. Development of subsequent (one-pot) tandem hydrogenation afforded saturated polyesters under mild conditions. The polymerizations under bulk (without solvent, 80-90 ºC) or in ionic liquids (50 ºC) under vacuum conditions enabled synthesis of high molar mass polymers (Mn >30,000 g/mol). The polymerization by molybdenum-alkylidene catalyst afforded the highest molecular weight polyesters (44000‒49400 g/mol, in toluene at 25 ºC) exhibiting promising tensile properties (strength and elongation at break) beyond polyethylene, polypropylene. Depolymerizations of these polyesters including closed loop chemical recycling were also demonstrated. Catalyst developments (more active, under mild conditions) play a key role for the efficient synthesis.

In the article, the authors presented the problem of the transition effect in bridge engineering, its causes, negative consequences, and suggested a solution involving the use of integral bridges with the embankment through a spatial bars structure using reinforced composite polymer material. Integral bridges are designed to collaborate with road or railway embankments in bearing loads. Additionally, their application minimizes maintenance and construction costs while enhancing durability. Current solutions in bridge engineering were described. It is predicted that the presented concept will reduce the amount of plastic waste and contribute to the long-term use of materials. The article emphasized the importance of sustainable development, recycling, and the potential application of substitute materials.

The accumulation of waste plastics has a severe impact on the environment, and therefore, the development of efficient chemical recycling methods has become an extremely important task. In this regard, a new strategy of degradation product-promoted depolymerization process was proposed. Using N,N'-dimethyl-ethylenediamine (DMEDA) as depolymerization reagent, an efficient chemical recycling of poly(bisphenol A carbonate) (BPA-PC) material was achieved under mild conditions. The degradation product 1,3-dimethyl-2-imidazolidinone (DMI) was proven to be the critical factor in facilitating the depolymerization process. This strategy does not require catalysts or auxiliary solvents, which is truly green process. This method improves the recycling efficiency of BPA-PC and promotes the development of plastic reutilization.

This review provides an extensive overview of the developments in the field of polymer science, focusing on the solid-state modification (SSM) of thermoplastic materials. The background of the study places thermoplastics within the context of their increased use over the past century, highlighting their versatility in various applications and the associated environmental and health concerns due to certain additives. The methods section delves into the specifics of SSM, a technique that involves the incorporation of monomers or oligomers into the amorphous phase of polymers through multiple exchange reactions, distinguishing it from traditional melt polymer modification methods. The results section outlines the unique aspects of SSM and its increasing recognition for its potential to enhance material performance in areas such as catalysts and composites. It also discusses the application of SSM in modifying different thermoplastic polymers, highlighting various studies demonstrating the method's effectiveness in altering polymer properties. Finally, this work emphasizes SSM's importance in environmental sustainability and its potential in the recycling and upcycling of plastic materials. It acknowledges the challenges and future perspectives in the field, particularly regarding the scalability of SSM techniques for industrial applications and their role in advancing a circular economy in the polymer industry.

Printed circuit boards (PCBs) make up 3 to 5% of all electronic waste. The metal content of spent PCBs can reach 40%. They usually contain valuable metals - Ag, Au, Pd, as well as other metals such as Cu, Sn, Pb, Cd, Cr, Zn, Ni and Mn. However metallic part of whole PCB is 40-60% including Cu layers between the fiberglass-polymer layers. The paper describes economics of the the valuable metals (Ag, Au, Pd) containing concentrate preparation from raw PCB. Considered the influence of pre-treatment method of PCB before the extraction of valuable metals on the extraction self-cost change. The disintegration method is based on the high-energy impact of the particles of the material to be ground, thus causing the separation of the metallic components of the PCB. In the course of the work, single and double direct grinding by the method of disintegration was studied. For the calculation the test batch 10’000 kg of two types of PCB were taken for estimation of the self costs and potential profit in case of complete valuable metals (Ag, Au, Pd) plus Cu extraction. Is shown that from 10’000 kg of studied PCB is possible to obtain 1144 and 1644 kg of metal-rich concentrate, which further should be subjected to electro-hydrochlorination for metals leaching. The main findings shows, that despite of high content of Cu in studied PCB, the commercial value is insignificant in total income from the Ag, Au and Pd sale. Was established correlation of the self-cost decrease after separative disintegration of PCB by metal content increase (by specific metals such as Au, Ag, Pd and also Cu) with the metal potential yield after extraction.

One of the most widely available and extensively produced varieties of industrial hemp, which generates a substantial amount of consumer-increasing waste in the form of hemp cellulose. In this study, recycling with a compressed and high-speed method that combines crushing and alkali treatment effectively converts leftover hemp fiber into ultrafine powder. SEM (Scanning Electron Microscopy), AFM (Atomic Force Microscope), FTIR (Fourier-transform Infrared Spectroscopy), and XRD (X-ray Diffraction) examined the original morphology of hemp fiber treated with alkali, fiber heated to 200 ℃, and crushed powder. Particle size, crystallinity, fiber surface, and strength increased and decreased. It became apparent that fiber strength decreased and fiber roughness significantly increased after alkali treatment. Fiber increased significantly, and crystallinity decreased after crushing. It was simple and effective for converting the leftover hemp fiber into micron-sized powder. In about 3 to 5 minutes, approximately 1 kg of dry ultrafine powder with a particle size of 10.44 μm was produced. This production method will significantly enhance future industrial applications of waste hemp fiber.

Summary: PURPOSE. Development of a drainless energy-saving technology for the processing of high-moisture iron-containing sludge from metallurgical production. RESEARCH METHOD. The regularities of the combined process of chemical dehydration of high-moisture iron-containing sludge by powdered waste of lime and dolomite, hardening and agglomeration by pressing in a single technological cycle on the developed experimental plant were studied. In the course of laboratory studies, the temperature of the mass, the rate of dehydration, the chemical composition of the mixtures, the appearance of the resulting briquettes, the weight loss during agglomeration-humidity of the mixtures, and mechanical strength of the briquettes were measured. RESULTS. New patterns have been established that have made it possible to develop a nonfiring method for producing iron-containing materials and self-healing briquettes. The essence of his method, which is one of the main provisions of scientific novel provisions, is to combine dehydration and self-hardening of the mixture with the process of shaping by applying external pressure to the hardening mixture in molds to obtain agglomerated material in the form of briquettes in a single technological cycle. The proposed technology does not require drying or firing, and a set of strength properties occurs as the material is cooled in air during the day. A new energy-efficient and drainless method for the production of iron-containing briquettes has been developed, which combines the processes of chemical dehydration and agglomeration in one technological cycle. CONCLUSION. The proposed project and technology will allow organization of production for the processing of high-moisture iron-containing sludge and the production a complex iron-containing material as a secondary metal-containing raw material for metallurgical plants for the production of steel and rolled metal. and dolomite dust from dry gas cleaning as dehydrating and binding materials, as well as screening of coke and coal as a reducing agents. The proposed technology also solves the problems of environmental pollution and land acquisition for the storage of production waste.

The increasing importance of batteries in the 21st century and the challenges posed by the anticipated growth in end-of-life batteries, particularly in Europe, are addressed. Projections indicate a significant increase in battery waste, with a specific focus on the recycling of black mass (BM)—a complex and hazardous byproduct of the battery recycling process. The research employs the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) methodology to systematically analyze the hazardousness of BM derived from various types of batteries. The findings reveal the inherently hazardous nature of BM, classifying it under multiple hazardous properties (HPs) according to European regulations. The urgent need for a definitive legislative classification of the hazardousness of BM is emphasized, and the potential of innovative technologies and strategies to improve recycling performance while mitigating risks is highlighted. The research significantly contributes to understanding the complexities of BM recycling, providing a foundation for future advancements in this area and emphasizing the need for further exploration and economic feasibility analysis of recycling technologies.

In the last ten years, plasma waste treatment has gained increasing prominence as a technology in response to growing challenges in waste disposal and the recognition of opportunities for generating valuable by-products. The efficiency and outcomes of this process are intricately linked to the characteristics of the plasma involved, such as plasma enthalpy and heat flux. We employed an experimental radio frequency inductively coupled plasma (RF-ICP) torch operating at atmospheric pressure to generate plasma. Utilizing optical emission spectroscopy (OES), we measured plasma parameters, specifically the effective electron temperature (Teff) and plasma density (ne), while varying argon gas flow rates and RF powers. Our investigations revealed that both flow rate and RF power exert significant control over plasma parameters, and we observed an unusual phenomenon within this range of discharge pressures. Consequently, both the plasma's enthalpy and the heat flux it generates are influenced by variations in both flow rate and RF power.

The accumulation of waste polymer in ecosystems is a problem that affects the environment on a global scale. This paper presents the design of Pwave+, a microwave pyrolysis system that has been optimized to recycle waste polymer into valuable hydrocarbon fuels and chemicals. Heating in a microwave oven is both volumetric and rapid, which improves the effectiveness of pyrolysis and the quality of the product. The production of waste polymer oil and gas products was boosted to its full potential by a continuous microwave vortex reactor. The product gases allowed for complete independence in terms of energy production. Modeling, simulation, and experimentation with advanced technology are used to optimize the pyrolysis parameters and the performance of the reactor. As a result, simulation and programming are solutions to problems. The results of this study demonstrated both the technical viability and the long-term viability of continuous microwave pyrolysis as a method for recycling mixed polymer waste streams. The Pwave+ continuous microwave vortex reactor is described in this study. It is capable of converting various polymer waste streams into hydrocarbon products as well as energy. The use of microwaves to assist in the pyrolysis process has the potential to cut down on plastic pollution and the amount of waste that is dumped in landfills. This could provide valuable insights for the design and commercialization of similar systems.

The recovery and recycling of metals that generate toxic ions in the environment is of particular importance, especially when these are tungsten and, in particular, thorium. The radioactive element thorium has unexpectedly accessible domestic applications (filaments of light bulbs and electronic tubes, welding electrodes, working alloys containing aluminum and magnesium), which lead to its appearance in electrical and electronic waste from municipal waste management platforms. The current paper proposes the simultaneous recovery of waste containing tungsten and thorium from welding electrodes. The simultaneous recovery is done by applying a hybrid membrane electrolysis technology coupled with nanofiltration. An electrolysis cell with sulphonated polyether–ether–ketone membranes (sPEEK) and a nanofiltration module with chitosan-polypropylene membranes (C–PHF–M) are used to carry out the hybrid process. The analysis of welding electrodes led to a composition of: W (tungsten) 89.4%; Th 7.1%; O2 2.5% and Al 1.1%. Thus, the parameters of the electrolysis process were chosen according to the speciation of the three metals suggested by the superimposed Pourbaix diagrams. At a constant potential of 20.0 V and an electrolysis current of 1.0 A, the pH is varied and the possible composition of the solution in the anodic workspace is analyzed. Favorable conditions for both electrolysis and nanofiltration were obtained at pH from 6 to 9, when the soluble tungstate ion, the aluminum hydroxide and solid thorium dioxide were formed. Through a first nanofiltration, the tungstate ion is obtained in the permeate, and thorium dioxide and aluminum hydroxide in the concentrate. By adding a pH 13 solution over the two precipitates, the aluminum is solubilized as sodium aluminate which will be found after the second nanofiltration in permeate, the thorium dioxide remaining integrally (within an error of ±0.1ppm) on the C–PHF–M membrane.

Printed Circuit Boards (PCBs) are essential to most electronic devices. Digitalization and upgradation of gadget generates lots of PCB-containing electronic waste. Conserving resources and protecting the environment requires recycling such e-waste. The present paper is focused on the recovery of metals from PCBs by physical pretreatment and hydrometallurgical processes. Initially, the waste PCBs were pre-treated to separate metallic and non-metallic fractions. The metallic concentrate was leached using nitric acid (strong oxidative agent) for dissolution of metals. The system was fully jacketed with scrubber and condenser so that no emission of toxic gases to the environment. The process parameters viz. effect of acid concentration, pulp density, temperature, time, etc. were optimized and the obtained data were scientifically validated. Kinetics leaching fitted well with the Shrinking core model, XB = kc.t for Cu, (1-(1-XB)1/2) for Ni and 1-3(1-XB)2/3 + 2(1-XB) for Pb. The optimized conditions derived from these studies will be useful for recovery of metals from waste PCBs, and tin left in the residue could be further treated for the purpose of safe disposal or the utilization in an environmentally friendly manner. The developed process provides environmental benefits and has potential to be commercialized after scale-up studies.

The pressing process and density profile of particleboards produced with addition of waste wood containing phenol-formaldehyde (PF) resin was presented. The particles were melamine-urea-phenol-formaldehyde (MUPF) resinated. Recovered particles were obtained from post-industrial waste plywood. The press closing time recorded during the pressing of mats containing only recovered particles in the core layer (100%), at a unit pressure of 3 MPa, in which the face layer rate was 50%, resin load for face and core layer was 12% and 10% was shorter by 29% than for the industrial particle mats. Regardless of the level of variability of independent factors the overheating time of mats to a temperature of 100 °C, containing recovered particles was 10% - 20% shorter than the time of overheating mats with industrial particles. The greatest impact (52%) on maximum density of the face layer of particleboards was demonstrated by the content of the recovered particles and the resin load (32%). The maximum density area of the face layer was located closer to the surface in particleboards produced with a higher (80%, 100%) content of the recovered particles, a higher (i.e. 12% and 10%, respectively, for face and core layer) resin load, a lower (35%) face layer rate and a higher (3 MPa ) unit pressure.

The recycling of common soda-lime glass (SLG) is far from being complete, since the material may contain small polymeric, metallic and ceramic contaminations. This has a negative impact on the quality of new glass articles prepared via re-melting. Alternatively, the full reuse of contaminated cullets could be achieved by low-temperature consolidation into geopolymer-like materials. SLG powders, used either as received or pre-washed in acid solution, were added to a sodium aluminate solution at the room temperature for 3 h, under low-speed mechanical stirring. Microporous semi-crystalline monoliths were formed by the casting of suspensions in plastic molds and cured at 75°C overnight. The monoliths featured hydrosodalite as the main crystalline phase for as received SLG and LTA zeolite in the case of pre-washed SLG. The mechanical properties compared well with those of cementitious materials. Moreover, by addition of coarse glass particles as fillers, the methodology successfully yielded Venetian terrazzo-like samples, which could lead to significant material and energy savings in their manufacture. The proposed approach could also be extended to other difficult-to-reuse glass formulations and provide attractive and versatile up-cycled materials.

SDG target 12.3 calls for halving food waste at retail, food service, and household by 2030. The food waste index for this purpose includes parts attached to food that are usually removed intentionally ("unavoidable food waste") and allows counting the conversion to animal feed and utilisation as biomaterial as means of reduction. In Japan, the "Food Waste Recycling Law" which has been in effect since 2001, promotes the recycling of food waste generated from businesses, designating feed conversion as top priority. On the other hand, based on the more recent "Food Loss Reduction Promotion Act" of 2019, the government is currently promoting the reduction of avoidable food waste, as to meet the SDG target. Based on statistical sources and interviews with Ministry officers, this paper explains the history and achievements of Japan's 23-year policy based on the Food Recycling Law, as well as the tension between the two legislations.

New ways of generating energy are currently being discussed, with a transition from traditional primary sources to more environmentally friendly options, particularly renewables. Energy storage is also closely related to this transition. Battery storage currently dominates this area. However, flywheel energy storage system (FESS) technology offers an alternative that uses stored kinetic energy to be transformed into mechanical energy and, using a motor-generator, electrical energy. FESS technology is thus flexible and can be applied in different industrial applications. The management of the technology of recycling W-MMC waste material from other products and the subsequent trial production of high-strength W-MMC material with a density of more than 17 500 kg/m3 from recycled powders allowed to test the limits of the so-called "heavy" flywheels used in rotor production. Materials with densities ≥ 7 800 kg/m3, and operating at lower to medium speeds up to 20 000 rpm. The results achieved lead to the conclusion that the developed recycled materials of the W-MMC type with a density ≥ 17 500 kg/m3, with a yield strength of 1 200 - 1 700 MPa depending on the production method, can be used as a substitute for the structural steels used today, without an enforced reduction of the maximum allowed rotor speed due to exceeding the maximum allowed stress.

When disposing of waste metal resources in landfills, environmental issues such as soil contamination may arise. Recycling these resources not only recovers valuable metals but also mitigates environmental pollution. Platinum (Pt), a valuable metal used in fuel cells for its high water production activity, will see increased future demand as a fossil fuel alternative. This study analyzes the environmental and resource reduction effects of recycled Pt, considering the growing emphasis on its recycling for stable supply and demand of Pt. The environmental impact and resource consumption of recycled Pt with primary Pt (from natural mines) were compared and analyzed using the Life Cycle Assessment (LCA) technique. Results revealed that resource consumption for primary Pt was 8.25E+01 kg Sb-eq./kg, significantly more than the 5.45E+00 kg Sb-eq./kg for recycled Pt. This represents an environmental reduction effect of approximately 93%. In the case of greenhouse gas emissions, primary Pt emitted 1.35E+04 kg CO2-eq./kg, while recycled Pt emitted 6.94E+02 kg CO2-eq./kg, resulting in an environmental reduction effect of approximately 95%. In conclusion, recycling Pt, compared to primary extraction, offers substantial environmental and resource reduction benefits. This study underscores the significance of recycling and highlights the potential environmental improvements achievable through sustainable practices.

Industries are required to utilize treatment technologies to reduce contaminants in wastewater prior discharge and valorize by-products to increase sustainability and competitiveness. Most acid leaching gypsum purification studies have obviated the treatment of the highly acidic wastewater produced. In this work, acidic wastewater from acid leaching purification of post-consumer gypsum was treated to recover a valuable solid product and reusable water. The main aims of this work were to determine the impact of recirculating acidic and treated wastewaters on the efficiency of the acid leaching purification process and to valorize the impurities in the wastewater. Samples were characterized through X-ray fluorescence and X-ray diffraction. SimaPro 9.5 and ReCiPe 2016 midpoint method were used for the life cycle assessment of three wastewater management approaches. The reuse of the acidic wastewater did not improve the chemical purity of gypsum. Soluble impurities were precipitated at pH 10.5 as a magnesium-rich gypsum that could be commercialized as fertilizer or soil ameliorant. The alkaline treated water was reused for 6 acid leaching purification cycles without impacting the efficiency of the purification process. An acid leaching-neutralization-filtration-precipitation approach demonstrated superior overall environmental performance. Barriers and enabling measures for the implementation of an in-house wastewater treatment were identified.

As both governments and customers push for sustainable and recyclable textile products, textile companies will have to change their linear business model to a circular one. The aim of the present work is to help these companies take action by providing an update of the state-of-the-art of textile recycling technologies. Extensive desktop research was performed in order to prepare an overview of existing textile recycling technologies, their current state and prognosis, including also facilitating technologies for sorting and disintegration of textile products as well as virtual platforms that connect stakeholders and inform consumers.

Currently, with the rapid growth of the population, the demand for metals has increased, especially for the manufacture of electronic devices such as cell phones, computer equipment, among others. Once these devices stop working, most are sent to landfills, which represents a danger since these wastes contain metals and other materials that must be properly managed to prevent them from having a negative effect on the environment and the human being. On the other hand, e-waste contains valuable metals such as copper, gold, and silver, the concentration of which in these materials makes it cost-effective to recover. This paper presents a review of the extraction and recovery of valuable metals from electronic waste by hydrometallurgical methods, as well as patents and industrial processes related to the management and treatment of this waste.

The phenomenon of decreased serum uric acid (UA) levels in patients with Parkinson’s disease (PD) and its relationship with purine metabolic pathways remain unclear. We compared inosine, hy-poxanthine, xanthine, and UA levels in serum and cerebrospinal fluid (CSF) of PD patients with those of controls, and investigated the effect of changes in the purine metabolic system on UA levels in PD. Overall, 134 samples (serum, 45 PD patients and 30 controls; CSF, 39 PD patients and 20 controls), were analyzed using liquid chromatography-tandem mass spectrometry. A general linear model (GLM) was used to investigate relationships among purine metabolites. Compared to controls, PD patients had significantly lower UA levels in the serum and CSF, and serum and CSF UA levels were significantly correlated. Additionally, in PD, decreased serum hypoxanthine levels were observed with decreased CSF inosine and hypoxanthine levels, suggesting the involvement of the purine recycling system. GLM analysis indicated that the reduced UA levels in PD were mainly due to sources other than the purine metabolic system, such as exercise, nutritional indices, muscle volume, or adipose tissue. Our results highlight the impairment of purine recycling pathways in PD, as evidenced by the decreased serum hypoxanthine and CSF inosine.

Due to growing concerns about environmental pollution from plastic waste, plastic recycling research is gaining momentum. Traditional methods, such as incorporating inorganic particles, increasing cross-linking density with peroxides, and blending with silicone monomers, often improve mechanical properties but reduce flexibility for specific performance requirements. This study focuses on synthesizing silica nanoparticles with vinyl functional groups and evaluating their mechanical performance when used in recycled plastics. Silica precursors, namely sodium silicate, and vinyltrimethoxysilane (VTMS), combined with a surfactant, were employed to create pores, increasing silica's surface area. Early-stage introduction of vinyl functional groups prevented the typical post-synthesis reduction in surface area. Porous silica was produced in varying quantities of VTMS, and the synthesized porous silica nanomaterials were incorporated into recycled Polyethylene to induce cross-linking. Despite a decrease in surface area with increasing VTMS content, a significant surface area of 883 m2/g was achieved. In conclusion, porous silica with the right amount of vinyl content exhibited improved mechanical performance, including increased tensile strength, compared to conventional porous silica. This study shows that synthesized porous silica with integrated vinyl functional groups effectively enhances the performance of recycled plastics.

Transport infrastructure’s asphalt pavement deteriorates under the influence of destructive factors. Damages which have been occurred during its exploitation period are repaired, and when their further rehabilitation is economically and technically irrational, the asphalt pavement is recycled. The material from the asphalt pavement layer that has reached its limit state is milled out or broken and crushed and then is repeatedly used in the production of hot-mix asphalt (HMA) or warm-mix asphalt (WMA) mixtures. In this paper, the dynamics of the percentage recycling ratio (RR) of old asphalt pavement material was investigated. RR represents the quantity of reclaimed asphalt pavement (RAP) used in the production of HMA and WMA mixtures in Europe and the USA, divided by the total amount of RAP prepared in the country. Factors and goals affecting it are analyzed. An original system of 10 criteria that increase the RR country has been created. By applying different multiple criteria decision making (MCDM) methods and using the importance given to these criteria by 14 experts, the normalized subjective weights of the criteria were determined. Analytic Hierarchy Process (AHP), rank correlation, Average Rank Transformation into Weight - Linear (ARTIW-L) and Non-linear (ARTIW-N), Direct Percentage Weight (DPW) methods were used in the study. The results display that the RAP recycle rate is close to 100% in countries with a sustainable economic background. In the Baltic countries, it is mostly increased by the adequacy of regulatory documents, the strategy promoting asphalt recycling in the country, and the homogeneity and classifying of RAP. The number and capacity of RAP stocks, the number and productivity of asphalt milling equipment and the wear and tear of the asphalt pavement have the least influence on the increase of RR. The opinions of experts in assessing the significance of all criteria are consistent. The averages of the weights of criteria determined by four MCDM methods (AHP, ARTIW-L, ARTIW-N, DPW) made it possible to obtain more reliable results. These results can be used to make strategic decisions and to create a plan of practical actions to increase the RAP recycling rate in the developing countries.

Ranging from traditional food packaging, clothing, and furniture to the current small and large electronic devices and automobiles, plastics serve to fulfill diverse demands in our daily lives. However, the global plastic waste generation is dramatically escalating, currently standing at approximately 150 million metric tonnes annually. While some of regenerated plastics recycled by mechanical methods can be used as their parent plastics, cost and energy savings are limited by multiple preliminary processes such as plastic sorting, shredding, washing, and drying. Moreover, the continuous mechanical recycling process degrades the physical properties of the materials. In this context, chemical recycling is emerging as a promising alternative method due to its high efficiency, simple preliminary steps, reducing reliance on fossil resources, and conversion of plastic waste into value-added chemicals. This review provides a state-of-the-art overview of contemporary chemical recycling of polymeric materials via i) depolymerization: “polymers to small valuable molecules” and ii) closed-loop cycles: “polymers to monomers, and/or to polymers”, by encompassing both traditional/advanced depolymerization chemistries and the remaining challenges. These recycling approaches are contextualized within the present industrial technologies, key design principles, and specific recycling case studies related to distinct polymeric materials.

The drastically increasing amount of plastic waste is causing an environmental crisis that requires innovative technologies for recycling post-consumer plastics to achieve waste valorization while meeting environmental quality goals. Biocatalytic depolymerization mediated by enzymes has emerged as an efficient and sustainable alternative for plastic treatment and recycling. A variety of plastic- degrading enzymes have been discovered from microbial sources. Meanwhile, protein engineering has been exploited to modify and optimize plastic-degrading enzymes. This review highlights the recent trends and up-to-date advances in mining novel plastic-degrading enzymes through state-of-the-art omics-based techniques and improving the enzyme catalytic efficiency and stability via various protein engineering strategies. Future research prospects and challenges are also discussed

Nowadays the preservation and restoration of historical building needs to be faced in accordance with a novel sensibility regarding environment to preserve the future generations. In this context, the scientific community is focusing on novel and sustainable materials and techniques allowing durability and mechanical performances and at the same time compatibility with the existing heritage. Alkali activated materials represent a great challenge to produce new materials starting from the existing ones with reducing consumption, emission of greenhouse gases and environmental impact. This study deals with the valorization of waste materials coming from demolition and construction activities in the manufacture of geocomposites suitable for restoration and conservation of historical heritage. In particular, waste from tuff sawing and brick grinding were used as raw materials, then the geopolymeric samples produced were characterized from physical-chemical and mechanical point of view in order to investigate their performance and evaluate their suitability as materials for historical buildings recovery. Brick waste based geocomposites resulted to be more compact than the tuff-based ones as showed by the higher density values and the lower values of open porosity and water absorption and as further confirmed by the trend of the mechanical performance. Moreover, experimental data showed that physical and mechanical properties of both bricks and tuff waste-based geocomposites, even with different waste content, are compatible with existing building materials and to all the traditional repairing products.

Hundreds of thousands of kilometers of communication and power (umbilical) cables and flowlines lie undersea worldwide. Most of these offshore cables and flowlines have reached or will soon be nearing the end of their service life, necessitating the need for a viable recycling approach to recover some valuable material, e.g., copper. However, separation into constituent materials has proven very challenging due to the highly robust design of the composite cables (and flowlines) to withstand service conditions and the tough external plastic sheaths that protect against seawater corrosion. Here, we summarize the findings of the cryogenic comminution of subsea cables and flowlines for an effective separation and recovery of component materials. Heat transfer analyses of complex multilayer flowlines and umbilicals were conducted to evaluate the time required for these structures to reach their respective critical brittle-transition temperatures. Subsequently, the time was used as a guide to crush the flowline and umbilical cables under cryogenic conditions. The results show that the flowlines and umbilical cables will reach the brittle-transition temperature after approximately 1000s (i.e., 17 min) of submergence in liquid nitrogen (LN). Comminution of the materials at temperatures near the brittle-transition temperature was proven relatively efficient compared to room-temperature processing. The present evaluation of heat transfer and lab-scale crushing will afford accurate process modelling and design of a pilot cryogenic comminution of decommissioned flowlines in an LN-doped atmosphere.

Abstract: Like other plants, every PV power plant will one day reach the end of its service life. Calculations show that 20,400 tons of PV waste will be generated worldwide by 2030 and 60.2 million tons by 2050, not including the mass of the support structure. Such large amounts of waste pose a potential threat to the environment and people if not properly managed. The paper analysed the options for dealing with PV waste, namely reuse, recycling and landfilling. For recycling as the best option in terms of environmental protection and circular economy, an overview of recycling technologies and the percentage of achievable recycling for the materials contained in each PV system component is given. In addition, the current situation of legislation and recycling of PV modules in Europe was examined with special reference to the Balkan countries. There are a small number of factories for recycling PV modules in Europe, but none in the Balkan countries. The main reason for this is the small amount of PV waste in these countries and consequently the economic unprofitability. For this reason, PV modules (after dismantling the aluminum frame and cables) are mostly disposed of as non-hazardous waste in landfills in these countries. Finally, the main barriers to faster implementation of PV module reuse and recycling are listed, along with guidelines for their removal. The cost of recycling Si modules is about ten times higher than the cost of disposal. To change this ratio in favor of recycling, cheaper recycling methods need to be developed and taxes on landfill disposal need to be increased.

The rapid development of the photovoltaic (PV) industry will result in an increase in the amount of electrical and electronic waste from used PV panels. Only in Poland, the total capacity installed in photovoltaic sources in Poland in May 2020 exceeded 1,950 MW, and the installation weight was approximately 120,000. tone. The problem arises in the recycling or management of this waste. This work presents methods used to recycle waste into photovoltaic modules. The authors investigated the possibility of mechanical and chemical processing of crystalline silicon. A method of thermal treatment of the panel was also proposed. As a result of the research, it was found that the stage of separating materials (crystalline cream, EVO foil, aluminum frame) plays an important role in the recycling process, which is not easy. Chemical treatment allows the silicon to become plastic and the temperature melts the back layer of the panel.

In contrast to some low molar-mass per- and polyfluoroalkyl substances (PFASs), well-established to be toxic, persistent, bioaccumulative and mobile, fluoropolymers (FPs) are water insoluble, safe, bio-inert, durable niche high performance polymers which fulfil the 13 polymer of low concern (PLC) criteria in their recommended conditions of use. In addition, more recent innovations (e.g., the use of non-fluorinated surfactants in aqueous radical (co)polymerization of fluoroalkenes) from industrial manufacturers of FPs are highlighted. This review also aims at showing how these specialty polymers endowed with outstanding properties are essential (even irreplaceable since hydrocarbon polymer alternatives used in similar conditions fail) for our daily life (electronics, Energy, optics, internet of things, transportation, etc) and constitute a special family a part from other “conventional” C1-C10 PFASs found everywhere on the Earth and Oceans. Furthermore, some information reports the recycling (e.g. the unzipping depolymerization of polytetrafluoroethylene, PTFE, into TFE), end of life of FPs, their risk assessment, circular economy and regulations. Various researches are devoted to Environment involving FPs, though they represent a niche volume (with a yearly production of 330,300 tonnes) compared to all plastics (with 460 million tonnes). Complementary to other reviews on PFASs, which lack of such above data, this review presents both fundamental and applied strategies as evidenced by major FP producers.

Polyethylene terephthalate (PET) pollution poses significant environmental consequences, and thus new degradation methods must be explored to mitigate this problem. We previously demonstrated that a consortium of three Pseudomonas and two Bacillus species can synergistically degrade PET in culture. The consortium more readily consumes Bis(2-Hydroxyethyl) terephthalate (BHET), a byproduct made in PET depolymerization, compared to PET, and can fully convert BHET into metabolically usable monomers terephthalic acid (TPA) and ethylene glycol (EG). Because of its crystalline structure, the main limitation of the biodegradation of post-consumer PET is the initial transesterification from PET to BHET, depicting the need for the transesterification step in the degradation process. Additionally, there have been numerous studies done on the depolymerization reaction of PET to BHET, yet few have tested the biocompatibility of that product with a bacterial consortium. In this report, a two-step process was implemented for sustainable PET biodegradation, where PET is first depolymerized to form BHET using an Orange Peel Ash (OPA) catalyzed glycolysis reaction, followed by complete degradation of the BHET glycolysis product by the bacterial consortium. Results show that OPA-catalyzed glycolysis reactions can fully depolymerize PET, with an average BHET yield of 92% (w/w) and that the reaction product is biocompatible with the bacterial consortium. After inoculation with the consortium, 19% degradation of the glycolysis product was observed in 2 weeks, for a total degradation percentage of 17% when taking both steps into account. Furthermore, the 10-week total BHET degradation rate was 35%, demonstrating that the glycolysis products are biocompatible with the consortium for longer periods of time, for a total two-step degradation rate of 33% over 10 weeks. While we predict complete degradation is achievable using this method, further experimentation with the consortium can allow for a circular recycling process, where TPA can be recovered from culture media and reused to create new materials.

Sewage sludge is an organic waste generated in waste-water treatment plants with certain content of nutrients, what may potentially be used as a source of slow release fertilizer, especially as phosphorus (P) source, but it demands some pre-treatment and the content of P is much lower compared to soluble mineral fertilizers. For these reasons, composted sewage sludge was used to manufacture pelletized organomineral fertilizers, mixing it with the inorganic sources monoammonium phosphate (MAP) and AshDec® (ASD) (thermochemically incinerated sewage sludge). The fertilizers were physiochemically characterized and evaluated as to the dynamics of soil P solubilization, and the forms of P remaining according to its lability. The sources evaluated were: organic compost of sewage sludge powder (SSC), pelletized SSC (SCP), pelletized organominerals SSC+MAP (S+MAP) and SSC+ASD (S+ASD), ASD alone, all compared to a soluble mineral fertilizer (MAP), and a control without P fertilizer. A test was conducted in leaching columns with 50 g of soil (Oxisol), where the fertilizers were applied at a dose of 100 mg P/column, and 30 mL of water or 2% citric acid were added daily for 30 consecutive days. The collected leachates had pH measured and P content determined. Pelletizing process resulted in denser products and promoted more gradual P release. The organomineral S+MAP was the most water-soluble recycled source, solubilizing about 70% of the total P, while the others presented much lower solubilization (<20%). In contrast, all fertilizers showed high solubility in 2% citric acid (except for S+ASD). After leaching, the greatest amount of P remaining in the soil as labile and moderately labile. Composting and the AshDec process produced materials with slow P solubilization, which would be favoured to solubilize in acidic soils and acidic rhizosphere conditions. In turn, the organomineral mixture of SSC with a highly soluble mineral fertilizer (MAP) resulted in a promising product with intermediate nutrient solubility, better synchronized with crop demand, thus increasing efficiency in P use.

Investigating the potential impact of composting and recycling waste on income distribution are crucial to promote a fairer and more sustainable fresh tomato supply chain (FTSC). Therefore, this study aims to explore the potential of gaining extra income from recycling tomatoes waste generated along the FTSC and to calculate the contribution of extra income from recycling tomato waste to reduce income inequality along the FTSC. Data were collected from 136 greenhouse tomato producers, 60 wholesalers, 18 exporters, 120 domestic retailers, 22 overseas retailers, and 3 recycling facilities in Türkiye. Marketing cost, absolute marketing margin, relative marketing margin and net profit margin were used when economically analyzing the FTSCs. Research results showed that the net profit share of the producer decreased associated with the increasing number of intermediaries. Research results also showed that revenue gained from composting and recycling of product loss and waste increased the welfare of greenhouse producer more than other supply chain actors. When taking into account the revenue from composting and recycling of wastes, producers increased their net profit by 9.85% at first FTSC, while that of second and third FTSCs were 8.29% and 9.21%, respectively comparing to the prevailing conditions. The contribution of extra revenue from composting and recycling of wastes to retailers was more comparing wholesaler and exporter. Retailers and wholesalers gaining from recycling in domestic FTSCs was more comparing to overseas one. Close cooperation between producers, wholesalers, exporters, retailers, and recycling facilities is essential for the effective implementation of waste recycling initiatives. Organizing the training and education programs focused on waste management can increase the extra income of producers and active intermediaries in FTSC from composting and recycling tomato wastes. Offering financial incentives, grants, or subsidies can encourage producers and other actors within the supply chain to adopt waste recycling practices. Continuous research and innovation are crucial in identifying and developing new technologies, processes, and strategies to minimize food loss and waste. Dominating fair-trade practices to ensure that all FTSC actors may balance the income distribution among FTSC actors.

This scoping review examines global strategies and enterprises for sustainable solid waste management, with a focus on alternative landfilling approaches. The study collected and analyzed a significant number of documents from different regions, revealing Asia as the major contributor (for the collected documents) (48.7%), followed by North America (24.3%) and Europe (15.8%). Recycling emerged as the most effective alternative waste treatment method, representing 52.3% of the documented approaches, with industrial recycling (22.6%) and residential/non-residential recycling (20.2%) as prominent categories. Food waste was a significant concern across regions, constituting 21.4% of the collected documents. Composting was widely adopted (15.4%) due to its simplicity and benefits for gardening and soil improvement. Other methods like biogas extraction, reusing, raising awareness, incinerating, redistributing, reducing, and fermentation accounted for 13.1% cumulatively. The study highlights the need for tailored waste management solutions based on regional challenges and successful practices. Promoting recycling infrastructure, composting, and waste reduction approaches are crucial to achieving sustainable waste management aligned with SDGs. Collaboration and knowledge-sharing between regions are essential to improve inefficient waste management mechanisms. Integrating the findings into policymaking and industry practices can lead to a more sustainable future with reduced environmental impact.

The production of photovoltaic modules is increasing to reduce greenhouse gas emissions. However, this results in a significant amount of waste at the end of their lifespan. Therefore, recycling these solar panels is important for environmental and economic reasons. However, collecting and separating Crystalline silicon, Cadmium Telluride, and Copper indium gallium selenide panels can be challenging, especially in underdeveloped countries. The innovation of this work is to develop a process to recycle all solar panel waste. The dissolution of all metals is studied through the leaching process as the main step of the flowchart. In the first step of leaching, silver can be recovered 98% by 0.5 nitric acid. Then, the second and third step involves the use of glycine for base metals dissolution, followed by the leaching of valuable metals with hydrochloric acid. The effect of parameters such as initial pH, acid concentration, solid/liquid ratio, and Hydrogen peroxide concentration are studied. The results show that Cu, Pb, Sn, Zn, Cd, In, Ga, and Se can be recovered until about 100% under optimal conditions. The optimal conditions for the dissolution of Cu, Zn, and Cd were the glycine concentration of 0.5 M, Temperature of 25 ˚C, the solid/liquid ratio of 10 gr/l, and 1% of Hydrogen peroxide. The optimized glycine concentration for the leaching of lead and tin was 1.5M. Indium and gallium were recovered to 100% by the use of 5M Hydrochloric acid, S/L=10gr/l, and T=45 ˚C. Separation of selenium and tellurium occurred by 0.5 M HCl at a temperature of 60 ˚C. Additionally, for the first time, a general outlook for the recycling of various end-of-life solar panels is suggested.

A tumbler screen type residual film–impurity mixture wind separator as a key equipment for secondary utilization of farmland residual film. During the working process, the proportion of impurities in the separated waste mulch film intermittently increases, resulting in poor working stability of the device, which may hamper long-term operation. In this study, the material inside the separation unit was continuously monitored, and the main factor affecting separator per-formance was determined to be the challenges in the effective depolymerization of some residual film–impurity mixtures. The principles of agglomeration and depolymerization of the residual film–impurity mixtures were analyzed using computational fluid dynamics (CFD) and discrete element method (DEM) flow-solid coupling simulation methods. The key factor affecting the disaggregation of the mixture was the collision force between the residual film–impurity mixture and the trommel screen. The collision force was maximum when the residual film–impurity mixture first collided with the trommel screen when it was fed into the separation device. As determined by force analyses, the key factors affecting the collision force of the process were the material feeding amount and the structure of the inlet. Furthermore, simulations were carried out for different inlet structure forms; the evaluation index was the maximum collision force of the residual film–impurity mixture agglomerate on the trommel screen. The best disaggregation effect was obtained with a square feed inlet and at a feeding rate of 202 kg/h. A prototype was built using these specifications for verification. The average value of the ratio of impurities in the re-sidual film was 6.966%, the coefficient of variation was 7.38%, and the dispersion of statistical results was small. The ratio of impurities in the residual film was kept constant during the con-tinuous operation of the wind separator. Thus, this study analyzed the agglomerate disaggregation process and provided theoretical insights for deter-mining the optimal structures of the inlets of various cleaning devices and the feeding volumes.

Although a slightly radioactive element, thorium is considered very toxic because its various species, which reach the environment, can constitute an important problem for the health of the population. The present paper aims to expand the possibilities of using membrane processes in the removal, recovery and recycling of thorium from industrial residues reaching the municipal waste processing platforms. The paper includes a short introduction on the interest shown for this element, a weak radioactive metal, followed by highlighting of some common (domestic) uses. In a distinct but concise part, the bio-medical impact of thorium is presented. The classic technologies for obtaining thorium are concentrated in a single schema, and then the speciation of thorium is presented with an emphasis on the formation of hydroxo-complexes and complexes with common organic reagents. The determination of thorium has been highlighted both on the basis of its radioactivity, but especially through methods that call for extraction followed by an established electrochemical, spectral or chromatographic method. Membrane processes are presented based on the electrochemical potential difference, rapidly presenting barro-membrane processes, electrodialysis, liquid membranes and hybrid processes. A separate sub-chapter is devoted to proposals and recommendations for the use of membranes in order to achieve some progress in urban mining for the valorization of thorium.

Cigarette butts (CBs) are the most diffuse waste in the world, often abandoned in the environment without proper disposal. They are dangerous because of the numerous harmful chemicals poten-tially released in the environment. There are, in literature, several technological options for CB recycling, but some critical concerns could affect their effectiveness due to the quality and quantity of CB litter collected in the proper way. The present paper focuses on policy framework social behavior, waste collection and transport and technological processes. The Extended Producer Responsibility scheme for CBs is proposed at European level as an action to tackle CB litter and encourage sustainable product development. The CB waste collection and transport is a key step for bringing CB to the recycling process. The main concern is the small quantity of CBs collected: 0.06 % of the municipal waste and 0.18 % of the unsorted waste in the administrative area of Pe-rugia. Another crucial issue is the need for behavioral interventions to increase education and awareness of smoker citizens, addressing the discrepancy between smokers’ behaviors and beliefs.

During the production of furniture, large amounts of waste of these materials are generated, which are most often stored in warehouses without a specific purpose for their subsequent use. In highly developed countries, as many as 25 million tons of textile waste are produced annually, of which approximately 40% is non-clothing waste, such as carpets, furniture and car upholstery. The aim of the research was to produce and evaluate the dry-formed high-density fiberboards (HDF) with various shares of recycled particles of natural leather used in upholstery furniture production at different contents (1, 5 and 10% by weight). Mechanical properties (modulus of rupture, modulus of elasticity and screw withdrawal resistance) and physical properties (density profile, thickness swelling after water immersion, water absorption, surface absorption) were tested. The density profile and contact angle of natural leather have been also characterized. The results show that increasing the content of leather particles in HDF mostly has a positive effect on mechanical properties, especially screw withdrawal resistance and water absorption. It can be concluded, that, depending on the further use of HDF, it is possible to use recovered upholstery leather particles as a reasonable addition to wood fibers in HDF technology.

Post-industrial recycling (PIR) and post-consumer recycling (PCR) are measures to sustain re-sources by improving materials’ circularity and sustainability. Currently, circularity is mostly measured as the degree of reutilization of a material from 0 to 100 % at product or company lev-el. This lacks in assessing the resources’ usage over multiple product life cycles. Therefore, we propose to assess circularity as (i) the frequency resources are used in products (effective circu-larity eC) and (ii) a vehicle to reduce virgin resource use and environmental impacts (environ-mentally efficient circularity eeC). Besides, to compare the environmental impacts of using recy-cled materials from PIR or PCR, we analyse their impact reduction potential (IRP) indicating the environmental benefits of recycling in relation to virgin material put onto the market. We demonstrate the suggested indicators for a case study material: polypropylene. For this polymer type, the eC ranges between 0.93 and 9.08 uses of the resource on average depending on collec-tion, sorting, and recycling rates. Likewise, the eeC ranges between 0.31 and 1.50 uses per kg of CO2 equivalents emitted. PCR has a higher IRP regarding climate change impacts than PIR in all analysed scenarios. The results reveal the relevance of PCR and PIR beyond the product life cycle.

Recycled tire fibers (RTF) are currently one of the most abundant waste not being recovered due to several processing hurdles and the presence of high amounts of residual ground rubber particles (GR). Therefore, this study proposes a simple approach to separate most of rubber particles from fibers and to determine their rubber content using thermogravimetric analysis (TGA)/calcination. Afterwards, clean fiber (CF) and GR are used as fillers for recycled post-consumer low density polyethylene (rLDPE), and their effects on the physical properties are investigated. Accordingly, a series of composites with CF and GR is prepared at different filler concentrations (0-30%) via extrusion compounding before using compression molding and injection molding for comparison. In all cases, injection molding leads to higher strength and modulus, but lower elongation at break. The results show that incorporating 30 wt.% of CF into rLDPE yields a remarkable improvement in tensile strength (15%), tensile modulus (192%) and flexural modulus (142%). On the other hand, the incorporation of up to 30 wt.% of GR results in a reduction of both tensile strength and flexural modulus by 15%, confirming the critical role of the cleaning process for RTF in achieving the best results.

Natural cellulose hydrogels have been widely used to enhance mechanical properties. However, existing natural fiber composite hydrogels are not reusable, limiting their potential applications. To address this issue, we designed and prepared a polyvinyl alcohol/glycerol /bamboo microfibril double network tough hydrogel using a simple method. The bamboo microfibril and polyvinyl alcohol form a tight and rigid network through hydrogen bonding, improving mechanical properties. The prepared polyvinyl alcohol/glycerol/bamboo microfibril double network tough hydrogel has the advantages of reusability and fatigue resistance. Furthermore, both the elastic modulus and toughness of the hydrogel increase with increasing bamboo microfibril content. We also demonstrated that the hydrogel can be recast after cyclic compression, maintaining its recyclability, stability, and certain stiffness and toughness. Our study highlights the potential of hydrogels for controllable mechanical properties, fatigue resistance and shows that polyvinyl alcohol/glycerol/bamboo microfibril hydrogel has broad value for plasticity and reuse.

This article seeks to strengthen efforts in technological developments based on the classification of PET plastic that positively impacts sustainable development and contributes to suitable solutions in collection centers in Mexico. Three experiment designs and machine learning tools for data processing were developed. For the experimentation, three factors were considered: the bottle's size, the amount of liquids inside the bottle, and the label on the bottle. The first experiment was to identify the distance of the sensor from post-consumer PET bottles. The second experiment was to determine the detection ability of the sensor with different levels of liquids inside the bottles, and the third was to determine the detection ability on the bottle labels. A digital lux meter on a microcontroller was developed to monitor illuminance on post-consumer PET plastic when it contains liquid as it passes through a conveyor belt for processing at an average rate of three bottles per second. With the implemented methodology, liquids were satisfactorily detected inside the transparent PET bottles when they had beverages between 25% and 100% of their capacity. Finally, this paper highlights that it is possible to implement an affordable design to identify bottles with liquids for collection centers.

Coffee is one of the most popular beverages in the world. Annual coffee consumption continues to increase, but at the same time, it generates a large amount of spent coffee grounds from the brewing process, that arises environmental problems. An appropriate solution to manage these spent coffee grounds becomes crucial. Our project aims to discuss the feasibility of utilizing the spent coffee ground to synthesize polylactic acid as a recycling application for spent coffee ground. This paper will discuss the properties and potential recycling applications of spent coffee grounds, the brief production process of polylactic acid, and the potential process for converting spent coffee ground to lactic acid. From our review, it is feasible to utilize spend coffee ground as the primary sources for lactic acid production by bacteria fermentation, and further produce bioplastics, polylactic acids by ring-opening polymerization. Possible ways to improve the yield and corresponding cost analysis are also discussed.

The management of waste cooking oil (WCO) often poses significant challenges. Improper disposal of WCO results in negative environmental impacts and economic losses. However, from a circular economy perspective, WCO can be recycled and used as a sustainable feedstock for numerous industrial products, replacing virgin vegetable oils. This approach enables the recovery of resources while simultaneously addressing the problem of WCO disposal. By employing a multi-criteria decision analysis (MCDA) approach, the study assesses three alternative recycling pathways for WCO used as a feedstock in the production of A1) biodiesel, A2) biolubricant, and A3) biosurfactant. The aim is to identify the optimal alternative, taking into account environmental, economic, and technical factors. The procedure involved a team of chemical engineers working in the WCO recycling sector who were selected as decision-makers. The 'priority scale' combined with the Paired Comparison Technique was employed as a weighting method to evaluate the selected criteria. The results revealed that the decision-makers considered environmental sustainability as the most crucial evaluation criterion, followed by the economic criterion. In contrast, the aspect of process management was deemed less significant. Among the compared alternatives, utilizing WCO as a feedstock for biosurfactant production was assessed as the optimal WCO recycling solution. This alternative not only demonstrated the lowest coefficient variation but was also deemed the most favourable option. Biolubricant production was determined to be the second-best alternative. The adopted MCDA approach proved to be a reliable and effective tool, enabling the clear identification of the preferred WCO recycling alternative among those assessed. This was achieved through the utilization of the decision-makers' expertise and knowledge.

The lithium-ion batteries are widely used as a power source for portable devices, including cell phones. The useful life is about 2 years or 500 cycles, contributing to the generation of waste from electrical and electronic equipment (WEEE). Mining of lithium and cobalt damages the environment and is onerous; therefore, sustainable alternatives, such as obtaining these elements from secondary sources as recycling of lithium-ion batteries, are essential to provide the inputs used in the sector. However, the metallurgical route which will used to recovering them must be considered, due to this work aims for a more environmentally favorable process using DL-malic acid 1.5 M and instead of compared with sulfuric acid 2 M, heat pretreatment of 1 h and 3 h, and for all conditions, experiments were carried out with and without adding the oxidizing agent hydrogen peroxide. The best yields occurred in presence of H2O2 10 % v/v, and heat pretreatment of 1 h: 33.49 % Co and 4.63 % Li, and 29.78 % Co e 3.44 % Li were recovered by sulfuric acid and DL-malic acid, respectively.

This study evaluated the grain size and high organic content from drinking water treatment sludge (DWTS) in the properties of ceramics. Samples were studied using raw and oven dried DWTS at 110 °C in two granulometries (0.180 mm and 0.075 mm), with and without calcination (550 °C), as partial replacement of two soils commonly used in ceramic production. Specimens were prepared with 5, 10, and 20% DWTS and calcined at 950 °C to determine their chemical, physical, mineralogical and mechanical properties. The DWTS reduced the density and increased the absorption and shrinkage of the specimens after calcination. An increase in strength with up to 10% sludge, driven by the presence of fluxing agents, was verified. The processing method had little influence on the properties of ceramic with above 10% of sludge. In conclusion, the use of raw DWTS obtained better results with low energy usage for its reuse.

Plastic waste constitutes one of the most important sources of pollution worldwide. Despite the growing recycling trend, nowadays there are no effective technologies that can compensate for the continuous increase in plastic production. Polyesters and polyamides are one of the most produced single-use plastics, mainly used in manufacturing textiles and soft drinks bottles. Today, only a very low fraction of these polymers can be recycled. It can be done by exploiting two leading technologies: mechanical and chemical recycling. Mechanical recycling represents, nowadays, the most used industrial application. However, it can treat a very narrow range of waste materials due to the impossibility of removing dyes and the deterioration of mechanical properties due to the incompatibility of different plastic materials. Another critical limit of this recycling technology is the limited number of recycling loops that can be done due to the thermal degradation that occurs during the extrusion process. The second possibility is chemical recycling, which allows the depolymerization of the original product to recover the monomers directly. The main drawbacks are the long reaction times and the many solvents needed to achieve high-purity products. Therefore, chemical recycling is economically feasible, only for big companies that can produce the virgin polymer in situ. In this work, a new technology has been patented. This process is constituted of three main steps. The first one is the distillation-assisted cyclodepolymerization (DA-CDP), introduced as a modification of the CDP process. In this unit, cyclic oligomers together with high molecular weight compounds have been produced. Then, after polymer purification, it is possible to achieve the same molecular weight of the initial polymer in less than 30 minutes, exploiting the ring-opening polymerization (ROP) in the next step.

Fresh water is an increasingly scarce resource in both urban and rural developments. As a response to this challenge, non-potable water reuse is on the rise. This research explored a potential off-grid system for water purification, consisting of a staircase wetland with terracotta pot plants working as a filter for greywater. The study further investigated the physicochemical properties of the greywater and the soil before and after the wetland purification. Results showed that the filtered water satisfied all requirements for water reuse, e.g., pH, turbidity, and total coliforms. The research then uniquely investigated the effect of greywater on the soil biodiversity and soil biomass using soil DNA extraction and the tea bag index testing method. The filtered greywater absorbed by soil decomposed the soil faster and stabilized it better compared to tap water-absorbed soil or unfiltered greywater. The DNA generation sequencing revealed no significant differences in alpha diversity between control and treatment samples. The beta diversity differences were significant. This nature-based solution can lead to reduced load on the sewage system, resulting in less wastewater generation.

During the MoDeCo2000 scientific and research project on mortars used in the territory of the Roman Danube Limes in Serbia, the biggest challenge was the quest for the provenance of used raw materials. The area where the largest city in the province of Moesia Superior developed, with millennial continuity of land use and settlement, was selected as a case study for deeper research. The material and immaterial values of Roman Viminacium have survived in the later life of the landscape, through the preserved building remains and artifacts, secondary use of building materials, but also toponyms, customs, and stories. Recycling of materials is commonly recognised in the modern age as the industrial processing of existing products in order to obtain raw materials and later prepare new products, representing one of the basic elements of sustainability. However, people throughout history have always used what they had at hand and the building remains were reused, but also recycled for new constructions. In this study we follow the presence of the specific material we call natural brick in the historical Viminacium landscape, focusing on Roman construction and specifically its potential use in lime mortars, connecting humanistic and natural sciences.

In this article we investigate the role of “Renewable Energy Consumption” in the context of Circular Economy. We use data from the World Bank for 193 countries in the period 2011-2020. We perform several econometric techniques i.e., Panel Data with Fixed Effects, Panel Data with Random Effects, Pooled OLS, WLS. Our results show that “Renewable Energy Consumption” is positively associated among others to “Cooling Degree Days” and “Adjusted savings: net forest depletion” and negatively associated among others to “GHG net emissions/removals by LUCF” and “Mean Drought Index”. Furthermore, we perform a cluster analysis with the application of the k-Means algorithm optimized with the Silhouette Coefficient and we find the presence of two clusters. Finally, we compare eight different machine learning algorithms to predict the value of Renewable Energy Consumption. Our results show that the Polynomial Regression is the best algorithm in the sense of prediction and that on average the renewable energy consumption is expected to growth of 2.61%.

Phosphorus (P) is the most important substance in inorganic fertilizers used in agriculture industry. In this study, a multi-product and multi-objective model is presented considering economic and environmental concerns to design a renewable and sustainable P-fertilizer supply chain management (PFSCM). To handle complexities of the proposed model, an ensemble knowledge-based three-stage heuristic-metaheuristic algorithm utilizing heuristic information available in the model, whale optimization algorithm, and variable neighborhood search (named H-WOA-VNS) is proposed. At first, a problem-dependent heuristic is designed to generate a set of near-optimal feasible solutions. These solutions are fed into a population-based whale optimization algorithm which benefits from both exploration and exploitation strategies. Finally, a single-solution metaheuristic based on variable neighborhood search is applied to further improve the quality of the solution using local search operators. The objective function of the algorithm is formulated as a weighted average function to minimize total economic cost, while increasing crop yield and P use efficiency. Experimental results over five synthetic datasets and a real case study of the P-fertilizer supply chain confirm the superiority of the proposed method against the state-of-the-art techniques. The results demonstrate that the proposed method performs well in optimizing both the economic cost and environmental issues.

In this article we investigate the impact of “Renewable Electricity Output” on green economy in the context of circular economy for 193 countries in the period 2011-2020. We use data from World Bank ESG framework. We perform Panel Data with Fixed Effects, Panel Data with Random Effects, WLS, and Pooled OLS. Our results show that Renewable Electricity Output is positively associated, among others, to “Adjusted Savings-Net Forest Depletion” and “Renewable Energy Consumption” and negatively associated, among others, to “CO2 Emission” and “Cooling Degree Days”. Furthermore, we perform a cluster analysis implementing the k-Means algorithm optimized with the Elbow Method and we find the presence of 4 clusters. Finally, we confront seven different machine learning algorithms to predict the future level of “Renewable Electricity Output”. Our results show that Linear Regression is the best algorithm and that the future value of renewable electricity output is predicted to growth on average at a rate of 0.83% for the selected countries.

Aerogel-based adsorbents present extraordinary sorption capacity for hexavalent uranium that can be as high as 8.8 mol kg–1 (2088 g kg–1). The adsorption data follow generally the Langmuir isotherm model and the kinetic data are better described by the pseudo-second-order kinetic model, which is associated with chemisorption. Evaluation of the thermodynamic data reveals that the adsorption is generally an endothermic, entropy-driven process (ΔHo, ΔSo > 0). Spectroscopic studies (e.g., FTIR, XPS) indicate that the adsorption is based on the formation of in-ner-sphere complexes between surface active moieties and the uranyl cation. Regeneration and uranium recovery by acidification and complexation using carbonate or chelating ligands (e.g., EDTA) have been found to be successful. The application of aerogel-based adsorbents to uranium removal from industrial processes and uranium-contaminated waste waters was also successful, assuming that these materials could be very attractive as adsorbents in water treatment and uranium recovery technologies. However, the selectivity of the studied materials towards hexavalent uranium is limited suggesting further development of aerogel materials which could be modified by surface derivatization with chelating agents (e.g., salophen, iminodiacetate) presenting high selectivity for uranyl moieties.

The vulcanization of rubber compounds is an exothermal process. A carbon black-filled and natural rubber-based (NR) formulation was mixed with different levels of sulfur (0.5, 1.0, 2.0, 4.0 and 6.0 phr) and studied with Differential Scanning Calorimetry (DSC) for the determination of the vulcanization enthalpy. It was found that the vulcanization enthalpy is dependent from the amount of sulfur present in the compound and the vulcanization heat released was -18.4 kJ/mol S if referred to the entire rubber compound formulation or -46.0 kJ/mol S if the heat released is referred only to the NR present in the compound. The activation energy for the vulcanization of the rubber compounds was also determined by a DSC study at 49 kJ/mol and found quite independent from the sulfur content of the compounds under study. A simplified thermochemical model is proposed to explain the main reactions occurring during the vulcanization. The model correctly predicts that the vulcanization is an exothermal process although it gives an overestimation of the vulcanization enthalpy which is larger for the EV vulcanization package and smaller for the conventional vulcanization system. If the devulcanization is conducted mechanochemically in order to break selectively the sulfur-based crosslinks, then the natural rubber compounds recovered from used tires can be re-vulcanized again and the exothermicity of such process can be measured satisfactorily with DSC analysis. This paper not only proposes a simplified mechanism of vulcanization and devulcanization but also proposes an analytical method to check the devulcanization status of the recycled rubber compound in order to distinguish truly devulcanized rubber from reclaimed rubber.

This paper presents the life cycle assessment results of a study of plastic recycling via hydrothermal upgrading (HTU), a chemical recycling technology. It was investigated due to its potential to address current gaps in the plastic recycling system, largely due to several plastic packaging materials and formats that cannot be processed by traditional mechanical recycling technologies (primarily due to technoeconomic reasons). As society transitions towards a net-zero-based circular economy, assessments should be conducted with a futuristic outlook, preventing costly mistakes by employing the right technologies in the right areas. HTU can generate up to 76% reduction in climate change impacts when compared with comparable end-of-life treatment technologies whilst conserving material with the system. Additionally, further reductions could be achieved by changes in electricity consumption within the study. This represents a new insight to chemical recycling of polymers by establishing a prospective life cycle assessment study that looks to introduce a step-change in the recycling system. By creating a transparent cut-off model with consistent allocation, it highlights the benefits of introducing this technology as opposed to the current model of disposal through incineration or landfill.

Mechanical recycling of solid plastic wastes on a small-scale level can be accomplished with the correct approaches. Thermoplastics are mostly considered for mechanical recycling because of their physical properties and ease of reprocessing. This paper reviews the mechanical reprocessing techniques of selected thermoplastics (polyethylene terephthalate and polyolefins) since they constitute a significant proportion of plastics used commercially. Furthermore, necessary considerations for effective operation of small-scale plants, including energy requirements of machinery and optimisation in order to improve efficiency and product quality, are discussed. A clearer understanding and addressing of the process-related challenges will lead to successful establishment and management of small-scale mechanical recycling facilities to benefit communities. Efficient small-scale mechanical reprocessing establishments have become essential in reducing the environmental impacts of solid plastic wastes and for energy conservation.

Recycling and waste management have garnered immense popularity in recent years, but few studies have been carried out regarding these systems. Therefore, an in-depth literature review was done in order to highlight the different sectors of the recycling system that need to be reformed. Hence this study examined recycling and waste management systems within three categories–medical, municipal, and plastic–that were carried out pre and post COVID by reviewing previous studies, technical reports, and annual reports. This was done by visiting numerous academic search engines alongside online resources that were utilized to assemble literature related to waste and recycling systems. Continuing a recurring idea was that no matter the type of waste, further research regarding all waste should be carried out. Additionally, since recycling and waste management are a vital part of our society, and seeing how unpredictable events such as the pandemic may be, it is paramount that that research is done not only on how the pandemic has affected systems now, but also how we can learn from current issues to utilize them for future “waste shocks”.

This publication highlights the effect of mechanochemical treatment in a high-speed thermoki-netic mixer as an alternative for recycling ground tire rubber (GTR). The GTR initially has an 80% gelled fraction and presented up to 50% gel fraction in the most intensive condition (5145 rpm, s2). Processing at the lowest speed (2564 rpm, s1) resulted in greater selectivity concerning the mechanochemical treatment (K~1). In the most intense processing condition (10 min. at s2), more significant degradation was observed via random scission with a reduction of the glass transition temperature, Tg (11ºC), an increase of the soluble polymer fraction, and a more signif-icant reduction in crosslink density. The artificial neural network could describe and correlate the thermal degradation profile and processing conditions with the physicochemical characteris-tics of the GTR. The approach presented here represents an alternative for mechanochemical treatment since it can reduce the crosslink density with selectivity and in short times (1-3 min.).

Excessive production, consumption and indiscriminate disposal of plastic waste cause an increasing plastic pollution with detrimental impacts on environment and human health. This study aimed to assess the level of knowledge, attitude, and practices (KAP) towards plastic pollution among Malaysians and evaluate the variation of plastic pollution related KAP among various socio-demographics. An online survey was conducted, and 294 valid responses was obtained. Descriptive statistics, KAP scoring and cross tabulation of responses were estimated. One-way analysis of variance, paired t-test and binary logistic regressions were carried out. Results showed that respondents had poor knowledge (mean 7.41 ± 1.80) and practice score (3.81 ± 1.39) across all socio-demographics. Compared to younger (18-30 years) respondents, older ones (>46 years) had higher knowledge (odds ratio, OR 4.304; p<0.01). However, middle aged (31-45 years) respondents reported significantly (p<0.01) higher attitude (OR 4.019) and practice (OR 4.056; p <0.05). Respondents with environmental related university education had showed higher odds about plastic pollution related knowledge (OR 10.343; p<0.01). Suggestions are made to undertake interventions such as environmental awareness creation, incorporating plastic pollution topics in formal and informal education, and providing recycling facilities nearby the localities for encouraging good practices towards minimizing plastic uses and pollution.

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

As the additive manufacturing industry grows, it is compounding the global plastic waste problem. Distributed recycling and additive manufacturing (DRAM) offers an economic solution to this challenge, but it has been relegated to either small-volume 3D printers (limiting waste recycling throughput) or expensive industrial machines (limiting accessibility and lateral scaling). To overcome these challenges, this paper provides proof-of-concept for a novel open-source hybrid 3D printer that combines a low-cost hanging printer design with a compression screw-based end-effector that allows direct extrusion of recycled plastic waste in large expandable printing volumes. Mechanical testing of the resultant prints from 100% waste plastic, however, showed that combining challenges of non-uniform feedstocks and a heavy printhead for a hangprinter reduced the strength of the parts compared to fused filament fabrication. The preliminary results are technologically promising, however, and provide opportunities to improve on the open source design to help process the volumes of waste plastic needed for DRAM to address the negative environmental impacts of global plastic use.

Since the process of waste recycling generates dust and flammable gas during fragmentation, there is always a risk of fire resulting therefrom, and fire does, in fact, frequently occur. However, research on disaster management at recycling facilities deals only with the problem of processing systems from a technical point of view, but it does not suggest concrete alternatives from a management point of view. Therefore, in this study, we analyzed the influence of the disaster response network of a waste recycling center at the organizational level based on the concept of the cognitive accuracy of a network when considering administrative aspects. Through this analysis, we confirmed that factors affecting the influence of the network exist, such that the entire network and the networks of different levels of position are different. We suggest that this can be improved by deploying members who perform formal tasks at the center of the network so that everyone can agree political approach.

The article provides an overview of nanocomposites and microelectronic elements used in space electronics and radiation control systems of nuclear reactors. Only those nanocomposites and microelectronic elements are taken into account that improve their characteristics in radiation fields or remain indifferent when exposed to ionizing radiation. Considering the chemical composition of the materials of these nanocomposites and microelectronic elements, it is analyzed from which radioactive materials (RM) obtained by recycling radioactive waste (RW) such composites and microelectronic parts can be made. Thus, an alternative way of radioactive waste disposal is proposed, when these wastes are used in the form of microelectronic elements designed to operate under conditions of cosmic radiation.

Mining is an important industry that provides products and services through infrastructure systems worldwide. However, the global development promotes the steady growth and accelerated demand for minerals, resulting in the accumulation of hazardous waste in land, sea and air environments and, consequently a series of environmental and health problems. Restoration techniques from mining tailing have become increasingly discussed among scholars due to their potential to offer benefits over reducing tailings levels, thereby reducing environmental pressure for the correct management and adding value to previously discarded waste. This review paper critically explores available literature on the main techniques of mining tailing recycling, and discusses leading recycling technologies, including the advantages and drawbacks, as well as future perspectives. The findings of this review contribute as a reference for scholars as well as support for decisionmakers concerning the related environmental issues.

The authors have revised the circularity of materials, which is important to stimulate circular activity processes. The theoretical part starts with describing the characteristics of the circular activity and the comparison of circular and linear systems in terms of recycling. Later on, the authors examined key elements important for the circularity and the results of an examination of various sectors. The authors formed a correlation matrix and used a dynamic regression model to identify the circular material use rate. The authors suggested a three-level methodology, using it provided a dynamic regression model which could be applied for forecasting the size of circular material use rate in European Union countries. The results show that private investments into recycling and the recycling of electronic waste and the recycling of other municipal waste categories are important in seeking to increase the usage rate of circular materials.

The Circular Economy of plastics is a promising concept that has the potential to reduce pollution and close the loop on plastic waste. However, further research is needed to develop more efficient and environmentally friendly methods of recycling plastic. This review article discusses the Circular Economy of plastics, its potential benefits and drawbacks, and the challenges that need to be addressed to make it a reality. Some case studies are also examined to explore how the Circular Economy of plastics has been implemented across the globe.

The article discusses an alternative way of recycling radioactive waste (RW), presented in the form of radioactive building materials - concrete and reinforced concrete structures and metal fittings, with the further use of materials, obtained during recycling, in the space industry. That is, it is supposed to send radioactive waste into space not as a passive ballast, but as a payload that will operate in space under conditions of increased radiation.

Edcraft, a recycling and upcycling event for Malaysian secondary school students, particularly in the Klang Valley area in 2020. The event's goal was to look into gamified solutions to encourage recycling and upcycling among the students’ age group. Lectures, talks, practical exercises and games were used to teach students about climate change and environmental preservation. According to a post-event survey, the percentage of participants who recycle has climbed significantly: 76% now recycle, compared to only 24% previously. The study discovered that gamification-based activities could effectively facilitate recycling and upcycling behaviours. Such solutions can be applied to encourage behavioural changes in different contexts. By interviewing 15 Edcraft students in a focus group study setting, researchers could better understand the motivations. Themes such as 'social connections are vital', 'convenience and rewards are significant motivators', 'gamified activities help attract and engage teens' and 'environmental knowledge is crucial to prolonging recycling' emerged from the thematic analysis. This manuscript proposes gamified activities to induce a behavioural change in upcycling, and the findings yield helpful insights to fuel pro-environmental behaviours.

To substitute of conventional manure and peat with alternatives sourcing from environmental conservation concerns, several promising alternatives has been attracting scientific parties’ interest, recently. However, among them compost perform the best, mostly and support carbon sequestration and mitigation against climate change. The article describes the made locally produced 70% in volume olive pruning branches compost (COMP) performance in two trials as an organic amendment in pepper production and an olive sapling substrate during 2019-2021 organic management in Turkey. The application of COMP to pepper trial conducted using factorial randomised block design with 4 replications and 6 treatments increased total organic matter and soil organic carbon, significantly (p<0.05) as compared to non-used plots in two locations. The olive sapling trial was conducted using a randomised plot design with 4 replications and 4 treatments. After the 12 months of growth, compost had the largest architecture rooted plants significantly different (p<0.05). Fresh volume (cm³) of COMP used saplings were obtained 35% less than 40% peat treatment, significantly (p<0.05) while 6^th month measurement was found as 40%. It is concluded that to enhance circular economy recycling and composting olive pruning branches is lucrative for the country to reduce external input usage in organic horticultural production.

For every three people on the planet there is approximately two Tonne (Te) of available plastic waste. We show that carbon recovery from polystyrene (PS) plastic is enhanced by the co-addition to solvents to grow carbon nanotubes (CNTs) by liquid injection chemical vapour deposition. Polystyrene was loaded up to 4 wt% in toluene and heated to 780 °C in the presence of a ferrocene catalyst and a hydrogen/argon carrier gas in a 1:19 ratio. High resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and Raman spectroscopy were used to identify multi-walled carbon nanotubes (MWCNTs). The PS addition in the range from 0 to 4 wt% showed improved quality and CNT homogeneity; Raman “Graphitic/Defective” (G/D) values increased from 1.9 to 2.3; mean CNT diameters increased from 43.0 to 49.2 nm; and maximum CNT yield increased from 11.3% to 14.2%. Since both the CNT diameters and the percentage yield increased with respect to polystyrene addition, we conclude that carbon from the PS contributes to the carbon within the MWCNTs. The electrical contact resistance of acid washed Bucky papers produced from each loading, ranged from 2.2 to 4.4 Ohm, with no direct correlation to PS loading. Due to this narrow range, the materials with different loading were mixed to create six wires of an Ethernet cable and tested using iPerf to give uplink and downlink speeds of ~99.5 Mbps, comparable to Cu wire of identical dimension (~99.5 Mbps). The lifecycle assessment (LCA) of CNT wire production was compared to copper wire production for the use case in a Boeing 747-400 over the lifespan of the craft. Due to their lightweight nature the CNT wires decreased the CO2 footprint by 21 kTonne (kTe) over the aircraft lifespan.

The inherent value and use of hydrocarbon from waste plastics and solvents can be extended through open-loop chemical recycling as this process converts plastic to range of non-plastic materials. This process is enhanced by first creating plastic-solvent-combinations from multiple sources which are then streamlined through single process stream. We report on the relevant mechanics for streamlining industrially relevant polymers such as polystyrene (PS), polypropylene (PP), high-density polyethylene (HDPE) and acrylonitrile butadiene styrene (ABS) into chemical slurries mixed with various organic solvents such as toluene, xylene and cyclohexane. The miscibility of the polymer feedstock within the solvent was evaluated using the Relative Energy Difference method, and the dissolution process was evaluated using the “Molecular theories in a continuum framework” model. These models were used to design a batch process yielding 1 tonne/h slurry by setting appropriate assumptions including constant viscosity of solvents, disentanglement-controlled dissolution mechanism and linear increase of the dissolved polymer’s mass fraction over time. Solvent selection was found to be the most critical parameter for the dissolution process. The characteristics of the ideal solvent are high affinity to the desired polymer and low viscosity. This work serves as a universal technical guideline for open-loop chemical recycling of plastics avoiding the growth of waste plastic in a circular economy framework.

The introduction of any new disruptive technology in a traditionally well-established industry, such as the road construction industry, is usually associated with considerable resistance. This is especially relevant when the new technology is based on the use of granular materials traditionally considered to be of an unacceptable quality in combination with relatively new concepts such as New-age (Nano) Modified Emulsions (NME). In such cases, the fact that the material design methods are based on fundamental scientific principles and have been proven in laboratories and through Accelerated Pavement Testing (APT), may be of little influence. However, the general acceptance of new disruptive technologies, e.g. telecommunications and Information Technologies (IT), have been based on the considerable advantages it presented. The same principles are applicable to the general acceptance and use of NME stabilisation/enhancement of materials in the road construction industry. This article is aimed at the practical demonstration of the advantages of the use of nanotechnologies in the construction of the highest order roads (i.e. inter-city multi-lane highways) to lower order access roads (i.e. Low-Volume-Roads (LVR) and even local accesses to farms and in villages/townships). The implementation of NME technologies is directly associated with ease of use, time and cost savings and the addressing and reduction of risks.

There is an intense need to optimize agrivoltaic systems. This article describes the invention of a new testing system: the parametric open source cold-frame agrivoltaic system (POSCAS). POSCAS is an adapted gardening cold-frame used in cold climates as it acts as a small greenhouse for agricultural production. POSCAS is designed to test partially transparent solar photovoltaic (PV) modules targeting the agrivoltaic market. It can both function as a traditional cold frame, but it can also be automated to function as a full-service greenhouse. The integrated PV module roof can be used to power the controls or it can be attached to a microinverter to produce power. POSCAS can be placed in an experimental array for testing, agricultural and power production. It can be easily adapted for any type of partially transparent PV module. An array of POSCAS systems al-lows for testing agrivoltaic impacts from the percent transparency of the modules by varying the thickness of a thin film PV material or the density of silicon-based cells, and various forms of optical enhancement, anti-reflection coatings and solar light spectral shifting materials in the back sheet. All agrivoltaic variables can be customized to identify ideal PV designs for a given agricultural crop.

Calcium (Ca) is an essential element constituting sedimentary carbonate in subducting sediments. Ca isotopic characteristics of subduction-related rocks could provide insight into the behavior and budget of carbonate and carbon cycles in subduction zones, due to the distinctive δ^44/40Ca ranges of sedimentary carbonate with respect to the mantle. Here, we studied the Ca isotopic compositions of arc magmas from the Northern Luzon arc (NLA), which are evolved from a depleted mantle metasomatized by slab-derived fluids and sediment melts. The δ^44/40Ca values range from 0.76 ± 0.04‰ to 1.01 ± 0.03‰ and cover the typical ranges for bulk silica earth (BSE, ~ 0.94‰) and fresh mid-ocean ridge basalt (MORB, ~ 0.83‰). The Ca isotopes of NLA volcanics are not dominantly determined by the effects of mantle partial melting or fractional crystallization, nor significantly modified by secondary alteration. Instead, the δ^44/40Ca values of NLA volcanics are controlled by the subduction-related metasomatism. The metasomatism by slab-derived fluids (mainly expelled from altered oceanic crust, AOC) dramatically elevated the contents of fluid-mobile elements (e.g., Ba and Pb) with respect to fluid-immobile elements (e.g., Ce). This process, however, rarely modified the Ca isotopes, possibly ascribed to the δ^44/40Ca similarity between AOC and the depleted mantle. The δ^44/40Ca values significantly correlated with subduction indicators (e.g., Sr-Nd isotopes, Ba/Nb, Ce/Pb, and Nb/La), demonstrating the Ca isotopes of NLA volcanics are mainly controlled by the metasomatism of sediment melts subducting from the South China Sea (SCS). Based on the thermal structures and chemical compositions of sediments subducting into global trenches, we propose that carbonate Ca isotopic signals can only be observed in the arcs with high sedimentary Ca fluxes and temperature-pressure conditions well beyond the solidus of H₂O-saturated sediment melting, e.g., NLA, Nicaragua, Guatemala, Colombia, Peru, South Chile, North Vanuatu, New Zealand, and Kermadec. The absence of such signals in other arcs suggests either limited sedimentary fluxes or much of the subducting sedimentary carbonate has been survived during plate subduction to enter the deep mantle.

The 2018 summer drought in Europe was particularly extreme in terms of intensity and impact due to the combination of low rainfall and high temperatures. However, it remains unclear how this drought developed in time and space in such an extreme way. In this study we aimed to get a better understanding of the role of land-atmosphere interactions. More specifically, we investigated whether there was a change in water vapor originating from land, if that caused a reduction in rainfall, and by this mechanism possibly the propagation and intensification of the drought in Europe. Our first step was to use remote sensing products for soil moisture content (SMC) and the normalized difference vegetation index (NDVI) to see where the 2018 drought started and how it developed in time and space. Our SMC and NDVI analysis showed that the 2018 drought started to impact the soil and vegetation state in June in Scandinavia and the British Isles. After that it moved towards the West of Europe where it intensified in July and August. In September, it started to decay. In October, drought was observed in southeast Europe as well. Based on the observed patterns we divided Europe into six regions of similar spatiotemporal characteristics of SMC and NDVI. Then, we used a global gridded dataset of the fate of land evaporation (i.e., where it ends up as precipitation) to investigate whether the drought intensification and propagation was impacted by the reduction in water vapor transported from the regions that first experienced the drought. This impact was investigated by identifying the anomalies in the water vapor originating from land recycling, imports and exports within Europe during the spring, summer, and autumn seasons. From these regions we identified four drought regions and investigated the changes in water vapor originating from source regions on the development of drought in those regions. It was found that during the onset phase of the 2018 drought in Europe that the water vapor originating from land played an important role in mitigating the precipitation anomalies as, for example, the share of land evaporation contributing to precipitation increased from 27% (normal years) to 38% (2018) during July in West of Europe. Land evaporation played a minor role in amplifying it during the intensification phase of the drought as the share of land evaporation contribution to precipitation decreased from 23% (normal years) to 21% (2018) during August in West of Europe. These findings are somewhat in contrast to similar studies in other continents that found the land surface to play a strong amplifying role for drought development. Subsequently, we found that the relative increase in the amount of land water vapor originating from eastern half of Europe played a role in delaying the onset and accelerating the decay of the 2018 drought in West of Europe.

Solid-state lighting has been replacing conventional lighting in the market, raising concerns for implementing an efficient end-of-life management system. Since LED waste streams have not been quite dominant, characterization studies (product-level characteristics, component-wise information, bill of materials, diversity, and differences) are inconsistent and having substantial gaps. This study investigates the end-of-life LED lamp literature, focusing on the bill-of-materials, and reveals that the characterization procedure suffers from a severe lack of sample representativeness. Consequently, characterization results are widely varied and not generalizable. Moreover, most of the studies did not inform and document the detailed sample characteristics, precluding the possibility of identifying reasons for variation. Combining available information from the recent studies, we present a mass distribution at the component level, exemplifying the prospect for meeting EU regulatory limit and the need for more insight at the lamp and component level. To fill the disconnection between lamp level characteristics and component and material content, we propose a characterization protocol that carefully documents lamp, component, and material level information by establishing a lamp-component–material composition nexus. The protocol may help researchers, policymakers, and industrial stakeholders conduct a systematic characterization, analyze complexities and prepare for a sustainable solution.

Additive manufacturing (AM) has been the core area of sustainable manufacturing commonly recognized for its high efficiency in enabling cost-effective production towards sustainability. There are three models this research constituted: In Collection-Recycling-Manufacturing (CRM) model, technologies and processes are benchmarked followed by Business model that evaluates industrial key criteria. However, these are insufficient for AM to effectively play dominant role as the realization requires human factors such as multi-entities authorities, policy making and AM society to initiate and execute the plan. Strategy control model focuses on human-centric approaches such as demography, population control, policy, regulations, and management. It investigates each nation’s demography, and enables strategy, plan and control to relocate overcrowding population to rural areas. It also produces robust workforce to support AM and materials recycling through the appropriate applications. Through the construction of AM and materials recycling, strategy control model creates job opportunities for those unemployed people. It further builds infrastructure for the livelihood of new residents and supports AM home-based business (HBB).

Highlights: A new material with a bending strength higher than that of concrete was developed using vegetable or fruit waste. The new material maintains the color, taste, and flavor of the original vegetable or fruit. Without water resistant treatment, the material is edible and can be conditioned with seasonings

Nonwovens made of recycled carbon fibers (rCF) and thermoplastic (TP) fibers have excellent economic and ecological potential. In contrast to new fibers, recycled carbon fibers are significantly cheaper and the CO2 footprint is mostly compensated by energy savings in the first product life cycle. The next step for this promising material is its industrial serial use. Therefore the process chain from fiber to composite material is analyzed. Initially rCF length at different positions during the carding process is measured. Thereafter the influence of the TP fibers onto processing, fiber shortening and mechanical properties is evaluated. At last several nonwovens with different TP fibers and fiber volume contents between 15 vol.-% and 30 vol.-% are produced, consolidated by hot pressing and tested by 4-point bending to determine the mechanical values. The fiber length reduction ranges from 20.6 % to 28.4 %. TP fibers cushion the rCF against mechanical stress but hold rCF fragments back due to their crimp. The resulting bending strength varies from 301 MPa to 405 MPa and the stiffness from 16.3 GPa to 30.1 GPa. Design recommendations for reduced fiber shortening are derived as well as material mixtures which offer better homogeneity and higher mechanical properties.

Microfluidic devices have been extensively investigated in recent years in fields including ligand-binding analysis, chromatographic separation, molecular dynamics, and DNA sequencing. To prolong the observation of a single molecule in aqueous buffer, the solution in a sub-micron scale channel is driven by the electric field and reversed after a fixed delay following each passage, so that the molecule passes back and forth through the laser focus and the time before irreversible photobleaching is extended. However, this practice requires complex chemical treatment to the inner surface of the channel to prevent unexpected sticking to the surface and the confined space renders features, such as a higher viscosity and lower dielectric constant, which slow the Brownian motion of the molecule compared to the bulk liquid. In this paper, we have fixed a capillary microchannel with an inner diameter of 2 microns on top of a piezo stage to recycle the molecule and collected the fluorescence by a confocal microscope. The passing times of the molecule through the laser focus are calculated by a real-time control system based on an FPGA and the commands of translation are given to the piezo stage through a feedback algorithm. We have achieved a maximum number of recycles of more than 200 and developed a maximum-likelihood estimation of the diffusivity of the molecule, which attains results of the same magnitude as previous reports. This technique simplifies the overall procedure of the single-molecule recycling and could be useful for the ligand-binding studies of biomolecules.

IntroductionThe use of protective masks, especially medical masks, increased dramatically during the COVID-19 crisis. Medical masks are made of synthetic materials, mainly polypropylene, and a majority of them are produced in China and imported to the European market. The urgency of the need has so far prevailed over environmental considerations.ObjectiveAssess the environmental impact of different strategies for the use of facemaskMethod Different strategies for the use of medical and community masks are being investigated for their environmental impact in this study. 8 scenarios, differentiating the typologies of masks and the modes of reuse are compared using several environmental impact indicators, mainly the Global Warming Potential (GWP100), and the plastic leakage (PL). This study attempts to provide clear recommendations that consider both the environmental impact and the protective effectiveness of face masks used in the community.Results The environmental impact of single-use masks is the most unfavorable, with a GWP of 0.4 -1.3 kgCO₂ eq., depending on the transport scenario, and a PL of 1.8 g, for a one month protection against COVID-19. The use of home-made cotton masks and prolonged use of medical masks through wait-and-reuse are the scenarios with the lowest impact.ConclusionThe use of medical masks with a wait and reuse strategy seems to be the most appropriate when considering both environmental impact and effectiveness. Our results also highlight the need to develop procedures and the legal/operational framework to extend the use of protective equipment during a pandemic.