The sustainable development of an area is highly dependable on reliable electrical energy supply. Microgrids are important in integrating distributed energy resources (DERs) using power electronic converters. However, microgrid control becomes challenging with the increasing number of distributed generators and loads. With the conventional droop control method, power contributions from DER converters cannot be accurately shared due to a mismatch of line impedances. In this paper, an augmented hierarchical control mechanism is proposed to solve the issues mentioned above. This hierarchical control mechanism consists of primary and secondary controllers. The primary stage utilized the droop controller to improve optimal power flow, mainly for the resistive network. The secondary stage is based on an improved methodology to compensate for the voltage and frequency variations during small and large signal disturbances. Moreover, the modelling and analysis for PMSG-based wind energy conversion systems are also presented. The response of the primary controller for the active and reactive power sharing is investigated. The analysis emphasizes the demonstration of optimal power-sharing under normal and abnormal conditions for the considered load. Finally, the suggested robust controller's performance is evaluated in MATLAB environment and simulation results show the proposed scheme's superiority under different operating conditions.

Pulmonary arteriovenous malformations (PAVMs) are vascular anomalies resulting in abnormal connection between pulmonary arteries and veins. In 80% of cases, PAVMs are present from birth, but clinical manifestations are rarely seen in childhood. These congenital malformations are typically associated with Hereditary Hemorrhagic Telangiectasia (HHT), a rare disease that affects 1 in 5,000/8,000 individuals. HHT disease is frequently caused by mutations in genes involved in the TGF-β pathway. However, approximately 15% of patients do not have a genetic diagnosis and, among the genetically diagnosed, more than 33% do not meet the Curaçao Criteria. This makes clinical diagnosis even more challenging in the pediatric age group. Here, we introduce an 8 years old patient bearing a severe phenotype of multiple diffuse PAVMs caused by an unknown mutation which ended in lung transplantation. Phenotypically, the case of study follows a molecular pattern HHT-like. Therefore, molecular biology and cellular functional analysis has been performed in primary endothelial cells (ECs) isolated from the explanted lung. The findings revealed a loss of functionality in lung endothelial tissue and a stimulation of endothelial to mesenchymal transition. Understanding the molecular basis of this transition could potentially offer new therapeutic strategies to delay lung transplantation in severe cases.

When separation to the parameters of interest appears below resolution limit of the estimator, the ambiguity arises whether two parameter estimates relate to one source emitted twice or two close sources emitted once. In the paper, novel Bayes technique aimed to identify one/two sources below resolution limit by the pair of Gaussian estimates of a source(s) planar location as parameter is developed. Prior probabilities of the hypotheses on one/two sources are available from the analysis of physical characteristics of the emissions, assuming that they can be equally probable. The identifier recalculates a posteriori these probabilities subject to a distance between sources. It is applied to distinguish two location estimates obtained in the planar time difference of arrival mobile communication network. The work of the identifier is studied in the domain of closely spaced network users where covariance matrices of estimates are sufficiently approximated by the constant. The application gives an example of how the identifier revises the prior probabilities and can change thereby the initial preference of a hypothesis with a distance between users in some cases.

The sound power LW of wind turbines (WTs) over the past decades has developed in relation to their electric power P as LW ∝ logP. The spectral distribution of the sound did not change significantly over time. This applies to the average performance of wind turbines, with differences between individual WT types. Because of the expected growth of onshore wind energy, a greater number of people will be living close to wind farms. This sustains the need for sound reduction. Sound reduction measures, such as serrations, reduced tip speed and low noise modes, may counteract the development of higher sound power from ever bigger WTs. To investigate this, the sound production of WT types over the last decades is analysed in relation to their size and electric power and the application of sound reduction measures. The analysis includes the broad band A-weighted and low frequency sound power levels as well as more detailed spectral distributions. Results show that the sound power level of wind turbines above 3 MW on average increases less with size than smaller turbines did. This is due to a lower blade tip speed and the use of sound reducing serrations. The spectral content of wind turbine sound, including the lower frequencies, has not changed significantly.

The integration of diverse distributed generation (DG) units, encompassing both Renewable Energy Sources (RES) and non-RES technologies delves into voltage levels, current distributions, and power flows, aiming to optimize and effectively manage the distribution network. An RES-based DGs such as photovoltaic systems and wind turbines, alongside non-RES units like fuel cells and micro turbines. This study proposes a hybrid approach the Multi-Objective Genetic Algorithm - Grey Wolf Optimizer (MOGA-GWO). By merging the strengths of multi-objective genetic algorithms with the efficiency of the Grey Wolf Optimizer, this advanced algorithm seeks semi-optimal solutions for multi-objective optimization problems. The algorithm aims to improve convergence speed without compromising solution quality, offering a promising solution for optimizing the characteristics of DG and RES integration in distribution networks compared to Cuckoo Search and Simulation Annealing Techniques. Key algorithmic operations include individual representation, initialization, fitness function computation, selection, crossover, mutation, and ending conditions. The DG optimal power flow problem is explored with a focus on minimizing generation costs, improving voltage profiles, minimizing losses, enhancing reliability, integrating renewable energy, reducing environmental impact, managing congestion, and ensuring compliance with operational constraints. Beyond traditional considerations, the study emphasizes neglected objectives and constraints, such as cyber-security concerns, real-time operation, regulatory frameworks, social acceptance, lifecycle environmental impact, grid resilience, data privacy, aging infrastructure compatibility, and economic viability.

This paper presents a novel framework for Collaborative Learning Networks (CLNs) in classrooms, aiming to optimize resource utilization and enhance educational services. The study addresses the inefficiencies of traditional education models, particularly the underutilization of computational resources and limited access to specialized software. The proposed framework employs a mix of task-based and random allocation strategies to distribute computational tasks within the CLN, considering each device’s capabilities and task requirements. The findings show significant improvement in resource utilization, facilitated by device-to-device collaboration and task sharing, thus enriching students’ learning experiences. This work contributes to optimizing resource utilization in education, advancing the field of CLNs.

Fragile X syndrome (FXS) is a genetic disorder caused by a mutation in the fragile X messenger ribonucleoprotein 1 (FMR1) gene and known to be a leading cause of inherited intellectual disability globally. It results in a range of intellectual, developmental, and behavioral problems. Fragile X premutation associated conditions (FXPAC), also caused by a smaller CGG expansion (55 to 200 CGG repeats) in the FMR1 gene, is linked to other conditions that increase morbidity and mortality for affected persons. Limited research has been conducted on the burden, characteristics, diagnosis, and management of these conditions in Africa. This comprehensive review provides an overview of the current literature on FXS and FXPAC in Africa, epidemiology, clinical features and challenges faced, such as discrimination against affected persons, limited awareness and research, poor access to resources and genetic services and treatment. It further provides an in-depth analysis of the existing worldwide data for the diagnosis and treatment of these disorders. This review will improve understanding of FXS and FXPAC in Africa by incorporating existing knowledge, identifying research gaps, and potential topics for future research to enhance the well-being of individuals and families affected by FXS and FXPAC in the region.

The correct selection of the value of p is a complex and iterative procedure that requires experience in the interpretation of the obtained interpolated maps. Inverse Distance Weighting is a method applied to the porosities of the K and L hydrocarbon reservoirs, discovered in the Neogene (Lower Pontian) subsurface sandstones in the northern Croatia (Pannonian Basin System). They represent small and large data samples. Also a standard statistical analysis of the data was made, followed by the qualitative-quantitative analysis of the maps, based on the selection of different values of the power distance exponent (p-value) for the K and L reservoirs maps. According to the qualitative analysis, for a small data set, p-value could be set on 1 or 2 giving the most optimal result, while for a large data set, a p value of 3 and 4 could be applied. By quantitative analysis, for the case of small data p=2 is recommended, resulting in a root mean square error value of 0.03458, a mean absolute error of 0.02013 and a median absolute deviation of 0.00546. Oppositely, a p-value of 3 and 4 is selected as appropriate for a large data set, with root mean square errors of 0.02435 and 0.02437, mean square errors of 0.01582 and 0.01509 and median absolute deviations 0.00896 and 0.00444. Eventually for a small data set, it is recommended to use a p-value of 2, and for a large data set, a p-value of 3 or 4.

Parkinson’s disease (PD) is the second most common degenerative disease which may cause blood pressure abnormalities due to autonomic dysfunction. Early morning rise of blood pressure which is called morning surge is found to be related with some cardiovascular diseases when it is exaggerated. We wanted to search the relation of Morning blood pressure surge (MBPS) and inflammation in PD. Method: Ambulatory blood pressure monitoring for 24 hours, fibrinogen to albumin ratio, hs-CRP are used in this retrospective study. Fifty idiopathic PD patients and 50 age and sex matched control cases were included. MBPS, it has been defined as the difference between morning BP (measured 2 hours after awakening) and the lowest night-time BP. Body mass index (BMI) is used as an independent variable. Results: Median value of MBPS for PD group (21,63) was significantly different from the control group values (18,63) (p

Fragile X syndrome (FXS), the most common monogenic cause of inherited intellectual disability and autism spectrum disorder, is caused by a full mutation (>200 CGG repeats) in the Fragile X Messenger Ribonucleoprotein 1 (FMR1) gene. Individuals with FXS experience a wide range of challenges related to social interaction (SI). Animal models, such as Drosophila melanogaster model for FXS where the only ortholog of human FMR1 (dFMR1) is mutated, have played a crucial role in understanding of FXS. The aim of this study was to investigate SI in the dFMR1B55 mutants using the novel Drosophila Shallow Chamber and a Python data processing pipeline based on social network analysis (SNA). In comparison with wild-type flies (w1118), SNA analysis in dFMR1B55 mutants revealed hypoactivity, fewer connections in their networks, a lower ability to efficiently transmit information, fewer alternative pathways for information transmission, a higher variability in the number of interactions they achieved, and tended to stay near the boundaries of the testing chamber. These observed alterations indicate the presence of characteristic strain-dependent social networks in dFMR1B55 flies, commonly referred to as the group phenotype. Finally, a combination of novel research tools is a valuable method for SI research in fruit flies.

Most existing coal-fired power plants were designed for sustained operation at full load to maximize efficiency, reliability, and revenue, as well as to operate air pollution control devices at design conditions. Depending on plant type and design, these plants can adjust output within a fixed range in response to the plant operating or market conditions. The need for flexibility driven by increased penetration of variable and non-dispatchable power generation such as wind and solar is shifting the traditional mission profile of thermoelectric power plants in three ways: more frequent shutdowns when market or grid conditions warrant, more aggressive load ramp rates (rate of output change), and lower minimum sustainable load, which provides a wider operating range and helps avoid costly plant shutdowns. Recent studies have shown that flexibility of a coal-fired power plant can be improved by energy storage. The objective of this work was to analyze a set of energy storage options and determine their impact on flexibility and economics of a representative coal-fired power plant. The effect of three energy storage systems integrated with a coal power plant on plant flexibility and economics was investigated. The results obtained in this project show that Energy Storage Systems integrated with a thermal power plant improves plant flexibility and participation in the Energy and Ancillary Services markets which improves plant financial performance. The study was funded by the U.S. Department Office of Fossil Energy FE-1 under Award Number DE-FE0031903.

The occurrence of chaotic instability of oscillations at the output of a single-stage amplifier on a powerful bipolar microwave transistor when a biharmonic signal is amplified is considered. It has been established that at a high level of the input signal at the output of the amplifier, the signal contains a significant chaotic component. Cases were experimentally studied when the frequency distance between the partial frequency components of a biharmonic signal is close to the gain band and when it is much smaller than this band. It has been established that in the first case, the chaos in oscillations is associated with the emergence of a sequence of trains of a forced oscillatory process with arbitrary initial phases and durations. In the second case, the appearance of a chaotic pedestal is associated with the chaos in the passive underexcited mode of the nonlinear circuit formed by the capacitance of the p-n junction and the input matching circuits of the amplifier stage.

When a grid-forming (GFM) inverter is connected to a low or medium voltage weak power grid, the line impedance with resistive-inductive characteristics will cause power coupling. Typical GFM decoupling control strategies are designed under nominal line impedance parameters. However, there are deviations between the nominal line impedance and actual parameters, resulting in poor decoupling effects. Aiming at this problem, this paper proposes a power decoupling strategy based on a reduced-order extended state observer (ESO). Firstly, the power dynamic model of GFM is established based on the dynamic phasor method. Then, the model deviation and power coupling due to line impedance parameter perturbation are estimated as internal disturbances of the system, and the disturbances are compensated on the basis of typical power control strategy and virtual impedance decoupling. Good decoupling performance is obtained under different impedance parameters, improving the control strategy's robustness. Finally, the effectiveness of the proposed method is verified by the results of RT Box hardware-in-the-loop experiments.

Recent advancements in semiconductor photonic and electronic devices such as Uni-travelling-carrier photodiodes (UTC-PDs), have played a significant role in the development of Terahertz communication technology. However, a major challenge that still persists is the limited output power from a single UTC-PD required for practical transmission distances. To enhance the output power, we propose and demonstrate a novel Terahertz wave power combining technique using a photomixer device that comprises of two arrayed UTC-PDs monolithically integrated with a microstrip line-based 2 × 1 Wilkinson power combiner and a rectangular patch antenna on a Silicon Carbide (SiC) substrate at 300 GHz. At photocurrents of 8 mA and 10 mA from the two UTC-PDs, the device experimentally exhibited a 7.3 dB increase in power relative to the power obtained with 8 mA UTC-PD and a 4.4 dB increase in power relative to the power obtained with 10 mA UTC-PD, when both UTC-PDs were irradiated. This implies that power can be enhanced by a factor of N2 if the photocurrent is multiplied by a factor of N. This technology presents a holistic and cutting edge platform for further power multiplication by further increasing the number of arrayed UTC-PDs.

Background. Escherichia coli commonly causes catheter-related bloodstream infection (C-RBSI) in specific populations. The differential time to positivity (DTTP) technique is the recommended conservative procedure for diagnosing C-RBSIs. Methods. We conducted a retrospective study of episodes in which E. coli was isolated from catheter lumens obtained using the DTTP technique. We analysed microbiological and clinical data based on the DTTP technique as either catheter colonization, C-RBSI, or non-C-RBSI. Results. We included 89 catheter blood cultures classified as follows: catheter colonization, 33.7%; C-RSBI, 9.0%; and non-C-RBSI, 57,3%. Catheter withdrawal was 15.7% without positive catheter-tip cultures. We found no statistically significant differences in catheter type, antibiotic treatment, or clinical outcome among groups, except for the frequency of catheter lock therapy or in the frequency of successful treatment. Mortality was associated with C-RBSI in only 1 patient. Conclusion. E. coli bacteremia diagnosed by the DTTP technique was non-catheter related in most patients. As the majority of the catheters were retained, E. coli bacteremia could not be microbiologically confirmed or ruled out as catheter related by catheter-tip culture. Future studies are needed to assess the profitability of the DTTP technique for diagnosing E. coli C-RBSIs..

A millimeter-wave (mmWave) gallium nitride (GaN) high-power amplifier (PA) monolithic microwave-integrated circuit (MMIC) was implemented, considering a source via effect. In this paper, we introduce guidelines for designing GaN high PA MMICs, from device sizing to meeting high-power specifications, power matching considering source via effects, schematic design of three-stage amplifier structures, and electromagnetic (EM) simulation. Based on the results of load pull simulation and small-signal maximum stable gain (MSG) simulation, the GaN high electron-mobility transistor (HEMT) size was selected to be 8×70 μm. However, since the source via model provided by the foundry was significantly different from the EM results, it was necessary to readjust the power matching considering this. Additionally, when selecting the source via size, the larger the size, the easier the matching, but since the layout of the peripheral bias circuit is not possible, a compromise was required considering the actual layout. To prevent in-band oscillation, an RC parallel circuit was added to the input matching circuit, and low-frequency oscillation was solved by adding a gate resistor on the PCB module. The proposed PA was fabricated with a commercial 0.1 μm GaN HEMT MMIC process. It exhibited 38.56 to 39.71 dBm output power (Pout), 14.2 to 16.7 dB linear gain, and 14.1% to 18.2% power-added efficiency (PAE) between 34 and 36 GHz. The fabricated GaN power amplifier MMIC shows competitive Pout in the Ka upper band above 33 GHz

The advent of social commerce (SC) has transformed the landscape of online consumer behavior, emphasizing the significance of customer-to-customer relations in shaping sustainable relation-ships with customers. This research investigated the intricate relationships between social com-merce dimensions, particularly suggestions and recommendations, forums and communities, and ratings and reviews, and their influence on customer-to-customer value co-creation (C2CVCC) and sustainable customer relationships (SCRs). A questionnaire was designed and administered to 635 respondents. We examined the psychometric properties of the measurements and subse-quently applied Partial Least Squares as a Structural Equation Modeling method (PLS-SEM) for hypothesis testing. The findings reveal that the dimensions of SC significantly impact C2CVCC, with ratings and reviews playing a pivotal role. Furthermore, C2CVCC emerges as a substantial mediator in the path between SC and SCRs. The empirical analysis showcases strong support for the proposed model, with robust path coefficients (β) and p-values confirming direct and indirect effects. These findings offer valuable insights for businesses seeking to leverage SC and customer interactions to enhance SCRs in the digital era. Understanding the dynamics of C2CVCC within the context of SC has become essential for marketers and businesses aiming to thrive in today's competitive online marketplace.

This work presents preliminary experimental results advancing non-destructive testing methods for detecting steel bars in concrete structures via contactless investigation in the X-band spectrum. The study reveals the field’s penetration into concrete, extracting insights into embedded bars through scattered data. Applying a quasi-quadratic inverse scattering technique to numerically simulated data yields promising results, confirming the effectiveness and reliability of the proposed approach. In this realm, using a higher frequency allows the use of lighter equipment and smaller antennas. Identified areas for improvement include accounting for antenna behavior and establishing undeformed target morphology and precise orientation. Transitioning from powder-based and sand specimens to real solid reinforced concrete structures is expected to alleviate laboratory challenges. Although accurately determining concrete properties such as relative permittivity and conductivity is essential, it remains beyond the scope of this study. Finally, overcoming these challenges could significantly enhance non-invasive testing, improving structural health monitoring and disaster prevention.

Wearable sensors have become increasingly popular for assessing athletic performance, but the optimal methods for processing and analysing the data remain unclear. This study investigates the efficacy of discrete and continuous feature extraction methods, separately and in combination, for modelling countermovement jump performance using wearable sensor data. We demonstrate that continuous features, particularly those derived from Functional Principal Component Analysis, outperform discrete features in terms of model performance, robustness to variations in data distribution and volume, and consistency across different datasets. Our findings underscore the importance of methodological choices, such as signal type, alignment methods, and model selection, in developing accurate and generalisable predictive models. We also highlight the potential pitfalls of relying solely on domain knowledge for feature selection and the benefits of data-driven approaches. Furthermore, we discuss the implications of our findings for the broader field of sports biomechanics and provide practical recommendations for researchers and practitioners aiming to leverage wearable sensor data for athletic performance assessment. Our results contribute to the development of more reliable and widely applicable predictive models, facilitating the use of wearable technology for optimising training and enhancing athletic outcomes across various sports disciplines.

Micro-Raman spectroscopy was carried out to evaluate the localized residual stresses in commercial Gallium Nitride-based devices, specifically AlGaN/GaN High Electron Mobility Transistors (HEMTs) in a novel packaging design provided by STMicroelectronics S.r.l. The packaging plays a key role in protecting the device core against the external environment, thus minimizing damages caused by mechanical shocks, exposure to light, and contact with chemicals, conjointly achieving an efficient heat dissipation rate. Even though the packaging is a required step for the proper functioning of ready-to-use electronic devices, its application typically may introduce mechanical stress to AlGaN/GaN HEMTs, which can result in various reliability issues. In this paper, we investigate the impact of packaging on residual stress by analyzing the frequency shift of the E2 Raman peak along GaN layers and at the GaN/Si interface. An extensive evaluation was conducted using both a packaged device and a wafer-level device. The correlation between Raman frequency shifts of the E2 mode was accurately quantified, revealing a stress mitigation of approximately 0.1 GPa. This reduction is ascribed to the compressive stress introduced by the packaging, which partially offsets the intrinsic tensile stress of the wafer-level device. The proposed methodology could, in principle, be implemented to improve the development of a packaging.

Papillary thyroid carcinoma (PTC) presents a significant health concern, particularly among Hispanic women in the United States, who exhibit a disproportionately higher chance of developing an advanced disease when compared to the non-Hispanic population. Emerging evidence suggests coagulation factor X, encoded by F10 gene, has a potential role in inhibiting cancer cell migration. However, comprehensive investigations into the differential expression patterns of F10 in Hispanic versus non-Hispanic females remain limited. RNA-sequencing data was acquired from the TCGA database for white female patients, 166 non-Hispanic and 25 Hispanic. A statistically significant (p < 0.05) 2.06-fold increase in F10 expression levels was detected in disease-free tumors compared to recurrent PTC tumors. Furthermore, an increase in F10 gene expression levels was also observed corresponding to approximately a 1.74-fold increase in non-Hispanic patients compared to Hispanic patients. The probability of tumor recurrence was 1.82 times higher in the cohort with low expression of F10 compared to the high expression cohort, correlating with the lower disease-free rates observed in Hispanic patients’ cohort when compared to non-Hispanics. This finding underscores the relevance of ethnic disparities in molecular profiles for understanding cancer susceptibility. Identifying F10 as a potential prognostic biomarker highlights avenues for targeted interventions and contributes to improving diagnostic and treatment strategies for diverse patient populations.

The electric vehicle (EV) industry is experiencing rapid growth, accompanied by continuous advancements in charging infrastructure to satisfy the rising need for fast and reliable charging. Particularly, the focus has shifted towards EV fast charging (EVFC) and its impact on the power grid. This paper presents a comprehensive analysis and survey of scholarly literature and projects conducted in this field over the past decade. The findings highlight the rising demand for EVFC and the need to address its potential adverse effects on the power grid. However, there is a noticeable lack of clear research guidance regarding charging time. To tackle these challenges and pave the way for future solutions, extensive research on DC fast charging, ultra-fast charging, and the integration of vehicle-to-grid (V2G) systems is required. This review paper thoroughly investigates the development of fast charging technology for electric vehicles (EVs), including its advantages and comparative analyses from various perspectives. Furthermore, it delves into the advancements in DC fast charging infrastructure, emphasizing charging standards and control modes. The study also investigates different categories of battery chargers for both on-board and off-board charging. Additionally, it explores the classification of DC-DC converters in the context of DC fast charging stations, discusses control strategies for EV systems, identifies existing challenges, and outlines future trends in EV fast charging.

Green and low-carbon development has become an important embodiment of China's path to becoming a strong agricultural country. How to enable agricultural enterprises to better adopt green technologies and conduct production and operation with the concept of sustainable development has become a key link. This article utilizes a structural equation model (SEM) to analyze the role paths and mediating effects of organizational learning ability and policy orientation in agricultural enterprises' market orientation and willingness to adopt green technologies[ The definition of green technology in this paper refers to Guo Kesha, Tian Xiaoxiao. Green technology and green transformation of industrial development mode [J]. Tianjin Social Sciences, 2024 (02) :99-107, including green manufacturing (production) technology and green service technology.]. The results show that market orientation, organizational learning ability, and policy effectiveness have significant direct positive impacts on the willingness to adopt; market orientation has a significant positive impact on agricultural enterprises' organizational learning ability, organizational learning ability has a significant positive impact on policy orientation, and market orientation has a significant positive impact on policy effectiveness; the results of mediation analysis also indicate that learning ability has a significant mediating effect between market orientation and willingness to adopt, and policy effectiveness has a significant mediating effect between market orientation and willingness to adopt. Through difference analysis, it is believed that the mediating effects of the three paths are equally important, and organizational learning ability and policy effectiveness play a partial mediating role in agricultural enterprises' willingness to adopt green technologies. Based on this, policy suggestions are proposed to improve enterprises' own organizational learning ability, increase the promotion of policies related to green technologies, improve relevant policies for the application of green technologies, and increase research and development efforts for green technologies.

Osteoporosis is considered a serious public health problem, particularly affecting the postmenopausal period. In 2018, in the Republic of Kazakhstan the total and primary incidence was 10 and 3.7 cases per 100,000 adults, respectively. The objective is to study osteoporosis prevalence and indicate main factors affecting low bone mineral density by screening adult population of Abay region, Kazakhstan. The target group were 641 respondents aged between 18 and 65 years old, Kazakh population living in Abay region since birth. All participants filled out questionnaire and had a bone mineral density measurement by dual energy X-ray absorptiometry (DXA) between July 15, 2023 and February 29, 2024. Logistic regression analysis was conducted to assess the association between low bone mineral density and key demographic characteristics, aforementioned lifestyle factors and nutrition habits. We identified the prevalence of low bone density and osteoporosis at the level of 34.1% with the highest prevalence in the older population group (50+ years) - 48.3%. Regression analysis revealed a number of indicators associated with the likelihood of bone sparing. However, only 4 of these showed significance in the final multivariate model (R2=22.4%). These included age (AOR 1.05), body mass index (AOR 0.92), fracture history (AOR 1.64), consumption of nuts and dried fruits were associated with lower prevalence of osteoporosis (AOR 0.48). Our study was the first in Kazakhstan that investigates the association of key demographic, behavior and anamnestic factors with low mineral density.

The article studies and analyzes a hybrid power source system, lithium battery, and fuel cell assisted by flexible photovoltaic panels for hybrid electric vehicles (HEVs). The new configuration operates based on optimizing the performance of the dual power source to maximize the available energy and operating time. The operational mode simulates specific driving conditions in urban, peripheral, and intercity routes under variable driving patterns and traffic conditions. The simulation results show that the new configuration increases the hybrid electric vehicle performance, providing higher reliability despite the more complex design. The proposed system reduces the external power supply dependence and avoids unexpected sudden stops due to energy exhaustion. The new configuration also extends the vehicle driving range depending on driving mode and route conditions. The vehicle driving range extension may reach up to 276.3 km. The hybridization of fuel cells with lithium battery and PV panel assistance enhances battery management, reducing battery servicing and increasing lifespan. The proposed topology is cheaper than a single fuel cell power system by 17.2%, reducing the total cost related to the single battery power system if we consider the battery recharge for its entire lifespan. The cost saving is 2.6% for the American market and 14.8% for the European one.

Electrification of society, increasing renewable energy sources and mobility charging lead to new loading patterns for power transformers. Dynamic load conditions induce enhanced mechanical stress on the transformers’ windings, potentially causing degradation of the solid insulation over time and compromising the transformer's short-circuit withstand capability. Thermal expansion of the windings, caused by losses in the copper conductors, occurring as the transformer is load-ed, increases the stress. Conversely, magnetic losses in the core and tie plate expansion contribute to a reduction in stress. This paper presents the effect of step changes in core losses and copper losses by on-line measurements of the clamping pressure, to better understand the mechanical stresses acting upon the solid insulation cellulose materials.

Recent years have witnessed significant advances in reinforcement learning (RL), which has registered remarkable success in solving various sequential decision-making problems in machine learning. Most of the successful RL applications, e.g., the games of Go and Poker, robotics, and autonomous driving, involve the participation of more than one single agent, which naturally fall into the realm of multi-agent RL (MARL), a domain with a relatively long history, and has recently re-emerged due to advances in single-agent RL techniques. Although, typically, the communication protocol between agents is manually specified and not altered during training, recently, some papers have shown signs of trying to emerge a communication between agents on the one hand and, on the other hand, to understand what is exchanged between agents. So, there is a growing body of literature on this topic which includes qualitative and quantitative studies and the ones that apply mixed methods. This study presents the scoping review of the methodological strategies undertaken in a total of 16 research articles. The results present the critical appraisal of quantitative methods in terms of validity and reliability and for qualitative methods considering four trustworthiness factors. In the end, relevant insights are further explored with implications and reflections on how they can benefit one's research in the field.

Fast Field-Cycling (FFC) Nuclear Magnetic Resonance (NMR) relaxometry is a powerful non-destructive magnetic resonance technique that enables, among other things, the investigation of slow molecular dynamics at low magnetic field intensities. FFC-NMR relaxometry measurements provide insight into molecular motion across various timescales within a single experiment. This study focuses on a \textit{model-free} approach, representing the NMRD profile $R_1$ as a linear combination of Lorentzian functions, thereby addressing the challenges of fitting data within an ill-conditioned linear least-squares framework. Tackling this problem, we present a comprehensive review and experimental validation of three regularization approaches to implement the model-free approach to analysing NMRD profiles. These include: (1) \nameUpe, utilizing locally adapted $L_2$ regularization; (2) \nameL, based on $L_1$ penalties; and (3) a hybrid approach combining locally adapted $L_2$ and global $L_1$ penalties. Each method's regularization parameters are determined automatically, according to the Balancing and Uniform Penalty principles. % Our contributions include the implementation and experimental validation of the \nameUpe{} and \nameUp{} algorithms, and the development of a "dispersion analysis" technique to assess the existence range of the estimated parameters. The objective of this work is to delineate the variance in fit quality and correlation time distribution yielded by each algorithm, thus broadening the set of software tools for the analysis of sample structures in FFC-NMR studies. The findings underline the efficacy and applicability of these algorithms in the analysis of NMRD profiles from samples representing different potential scenarios. 1

Preterm infants have increased body adiposity at term equivalent age and risk for adverse metabolic outcomes. The aim of the study was to define how nutrient intake may impact body composition (BC) of very low birth weight infants fed with early progressive enteral feeding and standard fortification. Eighty-six infants with

This research investigates the alignment of soft power and institutional skills in Montenegro's journey towards accession to the European Union (EU), with a particular focus on the environmental sector. An online survey targeting individuals employed in state institutions directly engaged in negotiation processes, notably the Ministry of Sustainable Development and Tourism and the Agency for Nature and Environmental Protection, was conducted. The research conducted an online survey, distributed before and after the summer recess to accommodate the transition of power following parliamentary elections, aimed at assessing the effectiveness of current personnel and identifying areas for improvement in staffing and negotiation strategies within Montenegro's environmental sector. Employing diverse methodologies, the survey's analysis delved into the demographic, social, and professional backgrounds of respondents. It explored their roles within institutions, involvement in environmental negotiations, and possession of relevant skills and expertise. Furthermore, respondents' knowledge of environmental issues, legislation, and challenges facing the country was assessed to gauge institutional capacity for environmental governance. Demographic data, including gender, age, education and regional origin, were collected to understand gender-specific attitudes and regional disparities in environmental perspectives. The sample of 84 individuals, comprising executives and employees from both institutions, provided insights into the age structure and regional diversity of personnel involved in negotiation tasks for Chapter 27. The selection of the Ministry of Sustainable Development and Tourism and the Agency for Nature and Environmental Protection reflects their pivotal roles in shaping Montenegro's environmental policies and addressing climate change challenges. This study aims to illuminate the dynamics of environmental governance within Montenegro's state administration, contributing to the country's path towards EU accession. The research findings highlight the critical need for Montenegro to prioritize strategic initiatives in personnel management, skill development, and institutional capacity-building within its environmental sector. The implications of this research extend beyond academia to inform policymaking and societal action, emphasizing the urgency for Montenegro to bolster its environmental sector capabilities, fostering both EU alignment and sustainable governance practices for the benefit of present and future generations.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

Abstract Octreotide is the first synthetic peptide hormone, consisted of eight amino acids, that mimics the activity of somatostatin, a natural hormone in the body. During the past decades, advanced instrumentation and crystallographic software established X-ray Powder Diffraction (XRPD) as a valuable tool for extracting structural information of biological macromolecules. The latter was demonstrated by the successful structural determination of octreotide at a remarkably high d-spacing resolution (1.87 Å) (PDB code: 6vc1). This study focuses on the response of octreotide to different humidity levels and temperatures, with a particular focus on the stability of the polycrystalline sample. XRPD measurements were accomplished employing an Anton Paar MHC-trans humidity-temperature chamber installed within a laboratory X’Pert Pro diffractometer (Malvern Panalytical). The chamber is employed to control and maintain precise humidity and temperature levels of samples during XRPD data collection. Pawley analysis of the collected data sets revealed that the octreotide polycrystalline sample is remarkably stable and no structural transitions were observed. The compound retains its orthorhombic symmetry (space group: P212121, a = 18.57744(4) Å, b = 30.17338(6) Å, c = 39.70590(9) Å, d~ 2.35 Å). However, a characteristic structural evolution in terms of lattice parameters and volume of the unit-cell is reported mainly upon controlled relative humidity variation. In addition, an improvement of signal-to-noise ratio in the XRPD data under a cycle of dehydration/rehydration is reported. These results underline the importance of considering the impact of environmental factors, as humidity and temperature, in the context of structure-based drug design, thereby contributing to the development of more effective and stable pharmaceutical products.

Abstract: : 2,3-dihydro-5,6,7,8-tetranitro-1,4-benzodioxine (TNBD), molecular formula =C8H4N4O10 is a completely nitrated in aromatic ring 1,4-benzodioxane derivative. The con-venient method of TNBD synthesis was developed (yield=81 %). The detailed structure of this compound has been investigated by X-ray crystallography. The results of differential thermal analysis (DTA) obtained with twice re-crystallized material showed onset at 247 and isoterm at 288 0C, with further total degradation at 300 0C. The experimental density 1,85 g/cm3 of TNBD was determined by X-ray crystallography. The spectral properties of TNBD (NMR, FT-IR, Ra-man) were explored. The detonation properties of TNBD calculated by EXPLO 5 code was slightly superior in comparison to standard high energy material - tetryl (detonation velocity of TNBD - 7727 m/s; detonation pressure - 278 kbar; tetryl – 7570 m/s and 226.4 kbar at 1.614 g/cm3, or 260 kbar at higher density - 1.71 g/cm3. The obtained preliminary results might suggest TNBD can be a potential thermostable high energy and density material (HEDM).

Alzheimer’s disease (AD) poses a significant public health challenge due to its irreversible and progressive nature while lack of a cure. As a potential strategy to combat AD, its prevention becomes increasingly attractive. Mild Cognitive Impairment due to AD (MCI-AD) represents a critical transitional stage between normal age-related cognitive decline and more severe AD conditions, occurring just before dementia onset. Unfortunately, there is currently no established animal model that accurately recapitulates MCI-AD characteristics. While many laboratories have traditionally used normally aged wild-type animals as experimental models, this approach falls short in representing the inherently worse state of MCI-AD compared to normal aging. To address this gap, we introduce an animal model—a transgenic mouse line with genetic inactivation of G protein-coupled receptor kinase-5 (GRK5), commonly known as the GRK5 knockout (GRK5KO) mouse. These GRK5KO mice exhibit amnesia, cognitive deficits, increased β-amyloid levels, neurofibrillary tangle (NFT) immunopositive axonopathy, and hippocampal neurodegenerative changes. Importantly, these pathological alterations predominantly impact the entorhinal, transentorhinal, and hippocampal cortices, aligning with human MCI-AD criteria and Braak stage II of human AD progression. Notably, female GRK5KO mice show approximately 2.5 times more NFT-positive axonopathy than males, mirroring the higher prevalence of AD cases in women. Collectively, existing data strongly supports the GRK5KO mouse as a qualified animal model for studying MCI-AD.

We investigate a singularly perturbed q-difference differential Cauchy problem with polynomial coefficients in complex time and space with quadratic nonlinearity. We construct local holomorphic solutions on sectors in the complex plane with respect to the perturbation parameter with values in some Banach space of formal power series in space with analytic coefficients on shrinking domains in time. Two aspects of these solutions are addressed. One feature concerns asymptotic expansions in the parameter for which a Gevrey type structure is unveiled. The other fact deals with confluence properties as q tends to 1. In particular the built up Banach valued solutions are shown to merge in norm to a fully bounded holomorphic map in all its arguments that solves a nonlinear partial differential Cauchy problem.

Ensuring the accuracy of wind power prediction is paramount for the reliable and stable operation of power systems. This study introduces a novel approach aimed at enhancing the precision of wind power prediction through the development of a multiscale hybrid model. This model integrates advanced methodologies including Improved Intrinsic Mode Function with Ensemble Empirical Mode Decomposition with Adaptive Noise (ICEEMDAN), Permutation Entropy(PE), Least Squares Support Vector Regression (LSSVR), Regularized Extreme Learning Machine(RELM), Multi-head Attention (MHA), and Bidirectional Gated Recurrent Unit (BiGRU). Firstly, the ICEEMDAN technique is employed to decompose the non-stationary raw wind power data into multiple relatively stable sub-modes, while concurrently utilizing PE to assess the complexity of each sub-mode. Secondly, the dataset is reconstituted into three distinct components: high-frequency, mid-frequency, and low-frequency, to alleviate data complexity. Following this, the LSSVR, RELM, and MHA-BiGRU models are individually applied to predict the high, mid,and low-frequency components, respectively. Thirdly, the parameters of the low-frequency prediction model are optimized utilizing the Dung Betele Optimizer(DBO) algorithm. Ultimately, the predicted results of each component are aggregated to derive the final prediction. Empirical findings illustrate the exceptional predictive performance of the multiscale hybrid model incorporating LSSVR, RELM,and MHA-BiGRU. In comparison to other benchmark models, the proposed model exhibits a reduction in Root Mean Square Error(RMSE) values of over 10%, conclusively affirming its superior predictive accuracy.

This article presents a description of a new method for solving the factorization problem, based on the gradient descent algorithm. This approach demonstrates significant improvements in efficiency compared to traditional methods proposed in previous research. This article describes a new method for solving the factorization problem, based on the gradient descent algorithm, and demonstrates the transition from algebraic methods to approaches based on functional analysis. The proposed approach not only improves the efficiency of solving the problem but also allows the application of computational algorithms of functional analysis, opening new possibilities for research and optimization.

In this paper, the single event burnout(SEB) and reinforcement structure of 1200V SiC MOSFET (SG-SBD-MOSFET) with split gate and schottky barrier diode(SBD) embedded were studied. The device structure was established using Sentaurus TCAD, and the transient current changes of single event effect(SEE), SEB threshold voltage, as well as the regularity of electricfield peak distribution transfer were studied when heavy ions were incident from different regions of the device. Based on SEE analysis of new structural device, two reinforcement structure designs for SEB resistance were studied, namely the expansion of P+body contact area and the design of multi-layer N-type interval buffer layer. Firstly, two reinforcement schemes for SEB were analyzed separately, and then comprehensive design and analysis were carried out. The results showed that the SEB threshold voltage of heavy ions incident from the N+source region was increased by 16% when using the P+body contact area extension alone; When the device is reinforced with multi-layer N-type interval buffer layer alone, the SEB threshold voltage increases by 29%; The comprehensive use of P+body contact area expansion and multi-layer N-type interval buffer layer reinforcement increased the SEB threshold voltage by 33%. Overall, the breakdown voltage of the reinforced device decreased from 1632.935V to 1403.135V, which can be seen as reducing the remaining redundant voltage to 19%. The device performance was not significantly affected.

Machine Learning deals with creating algorithms capable of learning from the provided data. These systems have a wide range of applications and can also be a valuable tool for scientific research which in recent years has been focused on finding new diagnostic techniques for particle accelerator beams. In this context SPARC_LAB is positioned, a facility located at the Frascati National Laboratories of INFN, where the progress of beam diagnostics is one of the main developments of the entire project. With this in mind, you aim to present the design of two neural networks aimed at predicting the spot size of the electron beam of the plasma-based accelerator at SPARC_LAB, which powers an undulator for the generation of x-ray Free Electron Laser (XFEL). Data-driven algorithms use two different data preprocessing techniques, namely autoencoder neural network and PCA. With both approaches, the predicted measurements can be obtained with an acceptable margin of error and most importantly without activating the accelerator, thus saving time, even compared to a simulator that can produce the same result but much more slowly. The goal is to lay the groundwork for creating a digital twin of linac and conducting virtualized diagnostics using an innovative approach.

Tumor to stroma ratio is a highly debated prognostic factor in the management of several solid tumors and there is no universal agreement on its practicality. In our study we proposed to confirm or dismiss the hypothesis that a simple measurement of stroma quantity is an easy-to-use and strong prognostic tool. We have included 74 consecutive patients with colorectal cancer who underwent primary curative abdominal surgery. The tumors have been grouped into stroma-poor (stroma <10%), medium-stroma (between 10 and 50%) and stroma-rich (over 50%). The proportion of tumor stroma ranged from 5% to 70% with a median of 25%. Very few, only 6.8% of patients had stroma-rich tumors, 4% stroma-poor tumors and 89.2%tumors with a medium quantity of stroma. The proportion of stroma, at any cut-off, had no statistically significant influence on the disease specific survival. This can be explained by the low proportion of stroma-rich tumors in our patient group and the inverse correlation of stroma proportion with tumor grade. The real-life proportion of stroma-rich tumors and the complex nature of the stroma-tumor interaction has to be further elucidated.

The methods of Artificial Intelligence (AI) have been used in the planning and operation of power systems for more than 40 years. In recent years, due to the development of microprocessor and data storage technologies, the effectiveness of this use has greatly increased. This paper provides a systematic overview of the application of AI including the use of Machine Learning (ML) to the power system. The potential application areas are divided into four blocks and the classification matrix has been used for clustering the AI application tasks. Furthermore, the data acquisition methods for setting the parameters of AI and ML algorithms are presented and discussed in a systematic way considering the supervised and unsupervised learning methods. Based on this, three complex application examples: wind power generation forecasting, smart grid security as-sessment (using two methods), and automatic system fault detection are presented and discussed in detail. Summary and outlook conclude the paper.

This work presents the mathematical framework of the Second-Order Comprehensive Adjoint Sensitivity Analysis Methodology for Response-Coupled Forward/Adjoint Linear Systems (abbreviated as “2nd-CASAM-L”), which enables the most efficient computation of exactly obtained mathematical expressions of first- and second-order sensitivities of a generic system response with respect to functions (“features”) of model parameters. Subsequently, the first- and second-order sensitivities with respect to the model’s uncertain parameters, boundaries, and internal interfaces are obtained analytically and exactly, without needing large-scale computations. Within the 2nd-FASAM-L methodology, the number of large-scale computations is proportional to the number of model features (defined as functions of model parameters), as opposed to being proportional to the number of model parameters, which are considerably more than the number of features, being incomparably more efficient and more accurate than any other methods (statistical, finite differences, etc.) for computing exact expressions of response sensitivities (of any order) with respect to the model’s features and/or primary uncertain parameters, boundaries, and internal interfaces. The application of the 2nd-CASAM-L methodology is illustrated using a simplified energy-dependent neutron transport model of fundamental significance in nuclear reactor physics.

This paper presents two control design strategies for voltage regulation in a single inductor dual output (SIDO) DC-DC Buck converter system. Based on a nominal multiple input multiple output (MIMO) plant model and performance requirements, both an LQR and a decoupled PI control laws are designed to control the power converter system, under parametric uncertainties such as voltage source variation, CPL power variation, and load resistance variation. Therefore, the SIDO converter can cascade operating, which may cause the undesired effects of voltage oscillation and reduce the system's stability margin. The control performance was assessed under both uncertainties resistive loading and power variation of a constant power load (CPL). A SIDO DC-DC Buck converter board has been developed for experimental tests. The experimental results show that the LQR strategy, compared to the PI strategy, presented a robust performance in the presence of parametric uncertainties in the resistive loads being, however, sensitive to uncertainties due to the presence of CPL loads.

In our study, we investigated the prognostic significance of hematological markers—NLR (Neutrophil-to-Lymphocyte Ratio), PLR (Platelet-to-Lymphocyte Ratio), and RDW-CV (Red Blood Cell Distribution Width - Coefficient of Variation)—in 117 glioblastoma patients. Data collected from January 2016 to December 2018 included demographics, clinical scores, and treatment regimens. Unlike previous research, which often examined these markers solely before surgery, our unique approach analyzed them at multiple stages: preoperative, postoperative, and before adjuvant therapies. We correlated these markers with overall survival (OS) and progression-free survival (PFS) using statistical tools, including ANOVA, Cox regression, and Kaplan-Meier survival analyses, employing SPSS version 29.0. Our findings revealed notable variations in NLR, PLR, and RDW-CV across different treatment stages. NLR and PLR decreased after surgery, with some stabilization post-STUPP phase (NLR: p=0.007, η2p=0.06; PLR: p=0.001, η2p=0.23), while RDW-CV increased post-surgery and during subsequent treatments (RDW-CV: p < 0.001, η2p=0.67). Importantly, we observed significant differences between the preoperative phase and other treatment phases. Additionally, higher NLR and RDW-CV at the second-line treatment and disease progression were associated with an increased risk of death (NLR at 2nd line: HR=1.03, p=0.029; RDW-CV at progression: HR=1.14, p=0.004). We proposed specific marker cutoffs that demonstrated significant associations with survival outcomes when applied to Kaplan-Meier survival curves (NLR at 2nd line < 5: p<0.017; RDW-CV at progression < 15: p=0.007). Elevated NLR and RDW-CV at later treatment stages correlated with poorer OS and PFS. No significant preoperative differences were detected. These biomarkers may serve as non-invasive tools for glioblastoma management.

The medium-voltage DC (MVDC) technology has gained increasing interests in recent years. Power electronics devices dominate those grids. Accurate simulation of such a grid, with detailed models of switching semiconductors, can quickly became very time-consuming, according to the number of connected devices to be simulated. A simulation approach based on interactions on a continuous time model can be very interesting, especially for developing a system level control model of such a modern MVDC distribution grid. Aim of this paper is to present all the steps required for obtaining a continuous time modelling of a +/- 10 kV MVDC grid case study, including Solid State Transformer (SST) and Modular Multilevel Converter (MMC) based Active Front End (AFE). Additional aim of this paper is to supply an educational content about the use of the continuous time simulation approach, thanks to a detailed description of the various devices modelled into the presented MVDC grid. The results of a certain number of simulation scenarios are eventually presented.

In (Semigroup Forum 77: 325-338, 2008) Mahmoudi M. and Renshaw J. solved a study that covers of cyclic $S$-acts over monoids. This article is an attempt to initiate the covers of finitely generated $S$-acts. We give a necessary and sufficient condition for a monoid to have the properties that $n$-generated $S$-acts have strongly flat covers, Condition $(P)$ covers and projective covers. The main conclusions extend some known results. We show also that Condition $(P)$ covers of finitely generated $S$-acts are not unique, unlike the situation for strongly flat covers. Additionally, we demonstrate that the property of Enochs' $\mathcal{X}$-precover of $S$-act $A$, where $\mathcal{X}$ denotes a class of $S$-acts that are closed under isomorphisms.

The aim of the work is to study the effect of the 3D printing process on the microstructural and hydrophilic properties of polylactic acid (PLA) samples with various model printing patterns obtained from the black Filament PLA by sequentially applying polymer layers using the FDM (Fused Deposition Modeling) method. X-ray phase analysis revealed partial crystallization of PLA polymer chains in printed samples, which occurs under thermal and mechanical action on the original amorphous PLA filament during 3D printing to varying degrees, depending on the geometry of the pattern and the morphology of its surface. At the same time, IR spectroscopy data indicate the preservation of all intrastructural chemical bonds of polylactide. Measured at the original installation, the values of the wetting edge angles on the surface of the printed samples are in the range φ = 50-60°, which is significantly less than the right angle. This indicates the hydrophilic properties of all samples’ surface. At the same time, the influence of different geometries of model drawings in printed samples was found not only on the morphology of the samples’ surface according to SEM data, but also on its wettability.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

The spectra and global distributions of the X-ray emissions generated by the solar wind charge-exchange (SWCX) process in the terrestrial magnetosheath are investigated based on a global hybrid model and a global geocoronal hydrogen model. The solar wind O6+ ions which are the primary charge state for oxygen ions in solar wind are considered. The line emissivity of the charge-exchange born O5+ ions are calculated by Spectral Analysis System for Astrophysical and Lab oratory (SASAL). It is found that the emission lines from the O5+ ranges from 105.607 to 118.291 eV with the strong line at 107.047 eV. We then simulated the magnetosheath X-ray emission intensity distributions with a virtual camera at two positions of north pole and dusk at six stages during the passing of a perpendicular interplanetary shock combined with a tangential discontinuity structure through the Earth’s magnetosphere. During this process, the X-ray emission intensity increases with time, and the maximum value is 27.11 keV cm-2 s-1 sr-1 on the dayside, which is 4.5 times that before the solar wind structure reaches the Earth. A clear shock structure can be seen in the magnetosheath and moves earthward. The maximum emission intensity seen at dusk is always higher than that seen at north pole.

This paper investigates an innovative photovoltaic cell configuration, denoted as “Au/CuSCN/RbGeI3/CdTe/ZnO/TiO2/FTO", using SCAPS-1D simulation. The research focuses on optimizing device performance by analyzing key components, including ZnO as the electron transport layer (ETL), RbGeI3 as the perovskite absorber layer, CuSCN as the hole transport layer (HTL), and CdTe as the active buffer layer. A comparison is made with the standard “Au/CuSCN/CH3NH3SnI3/CdTe/ZnO/TiO2/FTO" configuration under dark and illuminated conditions. Through an in-depth investigation involving temperature effects, generation rate analysis, RbGeI3 absorber layer thickness, Nd level, and interface defect levels, an optimized design for a unit area is achieved. The proposed solar cell demonstrates outstanding performance metrics, including an open circuit voltage (Voc) of 0.94V, a short circuit current density (Jsc) of 34.52mA/cm2, a fill factor (FF) of 77.77%, and an energy conversion efficiency (η) of 25.40%. These values significantly outperform the reference models with energy conversion efficiencies of 10.11% and 21.09%. Real-world applicability is validated by implementing these optimized characteristics in a photovoltaic system for Pakistan’s geographical location using PVSyst software. The suggested solar cell achieves a remarkable performance ratio (PR) of 85.6%, surpassing the PR of the reference basic solar cell model at 83%. The findings of this research offer a promising and superior solar cell design, incorporating innovative materials and optimization techniques to achieve exceptional energy conversion efficiency and overall performance. This study’s outcomes have the potential to advance photovoltaic technology and contribute to sustainable energy solutions worldwide.

In this paper, a continuous power management for a decentralized DC microgrid (DCMG) is proposed to achieve voltage regulation and power balance even under system uncertainty and voltage sensor failure. The DCMG system achieves a continuous power management through only the primary controller to reduce the computational burden of each power agent. To enhance the reliability and resilience of the DCMG system under voltage sensor failure, a DC bus voltage (DCV) sensor fault detection algorithm is proposed. In this algorithm, the DCV sensor failure is detected by comparing the measured DCV with the estimated DCV. When the power agent identifies the DCV sensor failure, it changes the operation properly according to the proposed control mode decision algorithm to maintain the stability of the DCMG system. When uncertain conditions such as the power variation of the distributed generations, sudden grid disconnection, DCV sensor failure, electricity price change, and critical battery status occur, the DCMG system is changed to transitional operation modes. These transitional operation modes are employed to transmit the power agent information to other agents without digital communication links (DCLs) and to accomplish power sharing even under such uncertain conditions. In the transitional operation modes of the DCMG system, the DCV levels are temporarily shifted to an appropriate level, enabling each power agent to detect the uncertainty conditions, and subsequently to determine its operation modes based on the DCV levels. Simulation and experimental results under different test conditions confirm the reliability and effectiveness of the proposed control scheme.

Background: Mental capacity is a fundamental aspect that enables patients to fully par-ticipate in various healthcare procedures. To assist healthcare professionals (HCPs) in assessing patients' capacity, especially in the mental health field, several standardized tools have been developed. These tools include the MacArthur Competence Assessment Tool for Treatment (MacCAT-T), the MacArthur Competence Assessment Tool for Clinical Research (MacCAT-CR), and the Competence Assessment Tool for Psychiatric Advance Directives (CAT-PAD). The core dimensions explored by these tools include Understanding, Appreciation, Reasoning, and Expression of a choice. Objective: This meta-analysis aimed to investigate potential differences in deci-sion-making capacity within the healthcare context among groups of patients with bi-polar disorder (BD) and schizophrenia spectrum disorder (SSD). Methods: A systematic search was conducted on Medline/Pubmed, and Scopus. Addi-tionally, Google Scholar was manually inspected, and a manual search of emerging re-views and reference lists of the retrieved papers was performed. Eligible studies were specifically cross-sectional, utilizing standardized assessment tools, and involving pa-tients diagnosed with BD and SSD. Data from the studies were independently extracted and pooled using random-effect models. Hedges g was used as a measure for outcomes. Results: Six studies were identified, with three studies using the MacCAT-CR, two studies the MacCAT-T, and one the CAT-PAD. The participants included 189 individuals with BD and 324 individuals with SSD. The meta-analysis revealed that patients with BD performed slightly better, and the difference was statistically significant, compared to patients with SSD, particularly in the domain of Appreciation (ES=0.23, 95% CI: 0.01 to 0.04, p=0.037). There was no statistically significant difference between the two groups for Understanding (ES=0.09, 95% CI: - 0.10 to 0.27, p=0.352), Reasoning (ES=0.18, 95% CI: - 0.12 to 0.47, p=0.074), and Expression of a choice (ES = 0.23, 95% CI: - 0.01 to 0.48, p=0.60). In the sensitivity analysis, furthermore, when considering only studies involving patients in symptomatic remission, the difference for Appreciation also resulted in non-significant (ES=0.21, 95% CI: -0.04 to 0.46, p=0.102). (ES=0.21, 95% CI: -0.04 to 0.46, p=0.102). Conclusions: These findings indicate that there are no significant differences between patients with BD and SSD during remission phases, while differences are minimal during acute phases. The usefulness of standardized assessment of capacity at any stage of the illness should be considered, both for diagnostic-therapeutic phases and for research and advance directives. Further studies are necessary to understand the reasons for the overlap in capacity between the two diagnostic categories compared in this study.

Rett Syndrome (RTT) is a severe neurodevelopmental disorder predominately diagnosed in females and primarily caused by pathogenic variants in the X-linked gene Methyl-CpG Binding Protein 2 (MECP2). Most often, the disease causing MECP2 allele resides on the paternal X chromosome while a healthy copy is maintained on the maternal X chromosome with inactivation (XCI) resulting in mosaic expression of one allele in each cell. Preferential inactivation of the paternal X chromosome is theorized to result in reduced disease severity; however, establishing such a correlation is complicated by known MECP2 genotype effects and an age dependent increase in severity. To mitigate these confounding factors, we developed an age- and genotype-normalized measure of RTT severity by modeling longitudinal data collected in the US Rett Syndrome Natural History Study. This model accurately reflected individual increase in severity with age and preserved group-level genotype specific differences in severity allowing for the creation of a normalized clinical severity score. Applying this normalized score to a RTT XCI dataset revealed that XCI influence on disease severity depends on MECP2 genotype with a correlation between XCI and severity observed only in individuals with MECP2 variants associated with increased clinical severity. This normalized measure of RTT severity provides the opportunity for future discovery of additional factors contributing to disease severity that may be masked by age and genotype effects.

Background: Glucose 6-phosphate dehydrogenase (G6PD) deficiency increases the risk of neonatal hyperbilirubinemia. The aim of the study is to evaluate the clinical findings of glucose 6 phosphate dehydrogenase (G6PD) and pyruvate kinase (PK) deficiency, to prevent further examinations for prolonged jaundice, and to contribute by regulating its treatment. At the same time, it is to determine whether systemic-immune-inflammation index (SII), neutrophil-to-lymphocyte ratio (NLR) and platelet-to-lymphocyte ratio (PLR) can be used in addition to conventional complete blood count (CBC) parameters in the diagnosis of neonatal prolonged jaundice. Methods: In full term neonates with hyperbilirubinemia who were admitted to Medicine Hospital between January 2019 and January 2024 with the complaint of jaundice, 167 infants with a serum bilirubin level above 5 mg/dL, whose jaundice persisted after the 10th day, were included in the study. Results: 63.5% of the patients were male and the mean age was 31±6 days. G6PD was negatively perfectly correlated with NLR (r: -1; p

This retrospective study examines 248 test-bolus examinations preceding contrast-enhanced magnetic resonance angiography (CE-MRA) to extract clinically relevant data for critical limb ischemia (CLI) management. Methods involved a retrospective review of test-bolus exams, analysing 60 graphs for time-to-peak (TTP), full-width half-maximum (FWHM) time, and time to continual rise in signal intensity. These values were correlated with heart function parameters (ejection fraction, ASA-Classification, Lee-Index, and MET-Score). Results indicate a mean TTP of 31.2 ± 7.3s, showing a correlation between ejection fraction and ASA classification. Patients with atrial fibrillation exhibited prolonged TTP compared to those without. Despite population heterogeneity, findings facilitate risk stratification for limb-saving interventions in CLI. TTP emerges as a potential clinical cardiovascular parameter and a risk factor for vascular interventions. Given the variation in injection protocols across centres, this study underscores the importance of precise bolus arrival time documentation for future multicentre studies.

The Active Distribution Networks (ADNs) are Multi-Input Multi-Output (MIMO) systems with coupled dynamics which cause interactions among the control loops of the Distributed Energy Resources (DERs). This undesired effect lead to performance degradation in the voltage control. To mitigate the effects of these unavoidable coupling, the present paper proposes a systematic design procedure based on the analysis of the interaction's sources. In details, each DER is equipped with a double loop PI to control the active and reactive powers output by the Voltage Source Converter (VSC) which connects the DER to the network's node. Furthermore, to guarantee Ancillary Services (ASs), the two loops are coupled by a simple mechanism of cooperation of the active power to voltage regulation realized by a filtered droop law. To achieve voltage regulation with reduced loop interactions, the PI parameters and the filter's pulse are designed according to a two sequential steps procedure based on the (Internal Model Control) IMC technique. Simulation studies are finally presented to demonstrate that the proposed design method achieves both reduction of the loop interaction and robust voltage control in presence of model parameter uncertainty in the MIMO model.

A testable hypothesis with quantitative predictions is put forward, proposing that strong acids produced on land are a major cause of increasing atmospheric pCO2. Our modelling analysis of reactions by dissolved inorganic carbon shows that increasing atmospheric CO2 could be caused thermodynamically by falling land surface pH values. This hypothesis challenges the imbalance assumed between the global uptake of CO2 by photosynthesis and emissions of CO2 from all sources, including the combustion of fossil fuels. Strong acids generated by oxygen from reduced nitrogen and sulphur emits CO2 almost stoichiometrically from dissolved bicarbonate in the pH range of most global soils from pH 6.5 to above 8. Each general decrease of aqueous pH value of 0.01 units from acidification of surface water potentially increases the pCO2 in the atmosphere by about 7 ppmv. Contrary to prevailing assumptions that CO2 emissions from combusting fossil fuels can remain in the atmosphere for more than a millennium, such emissions may be partly nullified by global greening from enhanced rates of photosynthesis as well as oceanic absorption. The surface pH value of the ocean has been shown to decrease as atmospheric pCO2 rises. Therefore, our qualitative estimates of increasing atmospheric CO2 driven by irreversible acidification on land are critical and need broad scale validation. To the extent that significant acidification of the land is occurring, through export of alkaline produce, the use of artificial nitrogen fertilisation and possible other causes, the prevailing methods of reducing CO2 emissions will fail. However, these acidifying processes on land have not been considered by previous biogeochemical reviews. Despite counter measures, including carbon capture and geological storage, the increasing Keeling curve for pCO2 may continue to rise because zero carbon policies do not address such a major cause. This hypothesis can be tested by in situ experiments in neutral soils and water, designed to compare CO2 emissions under the acidifying conditions described in this article with those when corrective counter measures are applied.

Keywords: Energy harvesting, Hybrid, Medical Wearable Sensor Nodes, Health Monitoring, Power Management

Understanding the genotype x environment (GE) interaction for traget trait is valuable for growers, agronomists, breeders and the seed industry. The objective of this study was to see and explore the genotype x environment interaction for grain yield of wheat to better guide genotype selection and breeding. The genotype main effect and GE interaction effect (GGE) biplots resolved the following three genotypes: 85 (ETW17-377), 82 (ETW17-374) and 13 (ETW17-281) for being the best yielding and stable. The Kulumsa site planted on 4^th of July 2017 (environment 7=E7) and the DebreZeit site on 20^th of July 2017 (E3) were the most effective environments in distinguishing the test genotypes and are thus suitable environments for future evaluation and selection with specific adaptation. Melkasa site planted on 4^th July (E9) was a representative environment where genotypes can be evaluated for wide adpaptation. The genetic covariate biplot indicated that thousand kernel weight (TKW) and plant height (PH) had significant positive associations with grain yield implying the possible concurrent indirect selection of both traits for exploiting GE interaction for grain yield of wheat.

Blockchain technology has emerged as a necessity for the decentralization of payment methods and transactions, but it has brought with it many properties of distributed systems that have made it a crucial technology for overcoming some of society's challenges, especially in the context of decentralizing services, transparency of information, availability, and security. Its architecture and communication methods, although possessing some complex nuances to understand, particularly for the lay audience in the field of distributed systems, protocols, and computer networks. In this article, we will explore some topics of distributed systems related to blockchain technology.

The extent of access to energy of displaced populations in settlements and camps in Africa is largely unknown, given 94% of displaced persons without access to electricity and 81% with a reliance on biomass for cooking. A multitude of contextual factors, such as the location and the characteristics of housing, the legal status, the socio-cultural background and the availability of humanitarian and public services impact the living conditions and the needed energy services. Limitations in accessing energy services have direct, multilayered, and far-reaching implications, including impacts on health, nutrition, education, protection, and livelihood. The objective of this article is to contribute to a more comprehensive understanding of the current state of energy ac-cess in displacement contexts on the African continent by identifying and utilizing existing data. After a screening of the vast and various available information, setting up of a database, consoli-dating the gathered data as well as assessing the quality through a quality assessment method, the currently available information is visualized and discussed. Remarkable differences in the access to electricity for displaced persons across the countries are found. For both electricity and clean cooking, the availability for displaced persons ranges from nearly no access at all up to an access rate of 100%. More strikingly, the results also show that besides South Africa, and the se-lected countries in the Maghreb region, the access to both clean cooking and electricity for dis-placed persons is remarkably low. At the same time, the poor data quality does not allow to draw solid conclusions nor impactful implementation activities. Novel conceptual frameworks and indicators are needed. Future research needs to focus on a more comprehensive understand-ing of how energy is interwoven in the lives of displaced persons, before a set of energy indicators can be derived. It is essential that the concerned persons, the displaced persons themselves are in-cluded in the research in a meaningful way.

A number of studies suggested that influenza vaccination can provide protection against COVID-19 but the underlying mechanisms that could explain this association is still unclear. In this study, the effect of the 2021/2022 seasonal influenza vaccination on the immune response to the booster dose of anti-SARS-CoV-2 vaccination was evaluated in a cohort of healthy individuals. One hundred and thirteen participants were enrolled, and 74 of them with no prior COVID-19 diagnosis or significant co-morbidities were considered for the analysis. Participants received the anti-influenza tetravalent vaccine and the booster dose of the anti-SARS-CoV-2 vaccine or the anti-SARS-CoV-2 vaccine alone. Blood was collected before and 4 weeks after each vaccination and 12 weeks after SARSCoV2 vaccination and analyzed for anti-flu and anti-spike-specific antibody titers and for in vitro influenza and SARS-CoV-2 neutralization capacity. Results indicated an increased reactivity in subjects who received both influenza and SARSCoV2 vaccinations, as compared to those who received only the SARS-CoV-2 vaccine, with sustained anti-spike antibody titers up to 12 weeks post-vaccination. Immune response to influenza vaccine was evaluated and individuals were stratified as high or low responders. High responders showed increased antibody titers against SARSCoV2 vaccine both after 4- and 12-weeks post-vaccination. On the contrary, the individuals classified as low responders were less responsive to the SARS-CoV-2 vaccine. These data indicate that both external stimuli, such as influenza vaccination, and the host's intrinsic ability to respond to stimuli play a role in the response to vaccine.

The transformation of the states of polarization of electromagnetic waves that interact with polarimetrically linear media can be represented by means of the associated Mueller matrix. A global measure of the ability of a linear medium to modify the states of polarization of incident waves, due to any combination of enpolarizing, depolarizing and retarding properties, is introduced as a distance of the Mueller matrix to the identity matrix. This new descriptor, called the polarizing power, is applicable to any Mueller matrix and can be expressed as a function of the degree of polarimetric purity and the trace of the Mueller matrix. The graphical representation of the feasible values of the polarizing power provides a general view of its main peculiarities and features. The values of the polarizing power for several typical devices are analyzed.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

To reduce the redundant counting of TDC in high-speed applications and thus reduce power consumption, a TDC architecture is proposed to quantify the difference between two adjacent rows of pixel signals. This structure can remove the identical part between two rows of pixel signals by adjusting the start and stop signal of the TDC, which will reduce the number of flipping of D flip-flops in the TDC. In the 110nm CMOS process, simulation results show that this design achieves an effective number of bits (ENOB) of 4.72 bits and a Figure of Merit (FoM) of 104.7 fJ/step - 162.3 fJ/step with a power consumption ranging from 60 µW to 93 µW. Compared with traditional counting methods, the proposed TDC can reduce counting power consumption by 30%.

Background. Escalating global plastic production, expected to reach 34,000 million tons by 2050, poses a significant threat to human and environmental well-being, particularly in aquatic ecosystems. Microplastics (MP) and nanoplastics (NP), which originate from the degradation of plastics, are of concern due to their potential bioaccumulation and uptake of pollutants. This study addresses identification methods and focuses on insect meal, a raw material for aquaculture feed. Methods. By using different techniques, the study was able to detect MP and NP in insect meal samples. Chemical digestion with KOH at 60°C efficiently removed organic matter without affecting the synthetic polymer polyethylene (PE). Filtration, confocal Raman microscopy, SEM and TEM were used for comprehensive analysis and integrity tests on PE films were performed using Raman and FTIR spectroscopy. The results showed the presence of PE microplastic particles in the insect meal, which was confirmed by correlative Raman and SEM mapping on a positively charged surface. In addition, the increased resolution of the Raman microscope identified submicrometric PE NP (800 nm). Transmission electron microscopy (TEM) with energy dispersive X-ray spectroscopy (EDX) confirmed plastic-like structures in the insect meal, highlighting the presence of PE plastics characterized by irregular shapes and some agglomeration. The higher carbon concentration in the EDX analysis supported the plastic nature, which was also confirmed by Raman spectroscopy. Conclusions. The study provides a robust method for the detection of MP and NP in insect meal and provides valuable insight into the possible presence of plastics in insect-based aquafeeds. The combination of different analytical methods increases the reliability of the results and sets the stage for future investigations that could focus on the quantification of NP and the assessment of their potential environmental impact.

There are several challenges on how to attain energy efficiency while maintaining balance among factors affecting energy consumption such as power rating and temperature setpoints of cooling units, room temperature and humidity, and indoor air quality (IAQ). A real-time energy and IAQ monitoring system were installed in an educational building to profile the operational power consumption of inverter-based air condition unit (ACU) installed in each room. Polynomial curve and neural fitting regression analysis were applied to the real-time power consumption, indoor temperature and humidity, and carbon dioxide (CO2) level data. The derived models were able to provide the stabilizing indoor thermal and air conditions of the room to reach steady state ACU power consumption. These collected data and calculated parameters can be used to define rules in automating control of cooling appliances for an efficient energy utilization. The regression approaches, using real-time data, have determined the influence of indoor heat conditions and carbon dioxide levels on ACU power consumption. These parameters were utilized to establish consistent values for temperature, humidity, and carbon dioxide levels under stable settings of inverter-based air conditioning units.

The aging mechanism of 10% and 30% nickel substituted manganese hexacyanoferrate cathode material in aqueous zinc-ion batteries has been explored through the advanced synchrotron-based two-dimensional x-ray fluorescence technique. Thanks to the two-dimension modality, not only the metal concentration dynamics throughout the entire electrodes was followed during the aging process, but their spatial distribution was also revealed, suggesting the route of the material transformation. The dissolution of Mn and Ni, and the penetration of Zn inside the framework, alongside the Mn aggregations outside the hexacyanoferrate framework were detected. Additionally, the possibility of conducting x-ray absorption spectroscopy measurements on the regions of interest made it possible to explore the chemical state of each metal, and furthermore, synchrotron-based powder x-ray diffraction demonstrated the gradual structural modification in 30% Ni-containing sample series, in terms of the different phase formation.

This article delves into the enduring relevance of Liberal International Relations (IR) Theory amidst persistent criticisms regarding power dynamics and its applicability in emerging states. Despite its detractors, Liberal IR Theory offers a nuanced understanding of state behavior, blending social contexts with power dynamics. It recognizes the intricacies of economic interdependence and advocates for a balanced approach in advancing democracy and human rights. While nationalism poses challenges to international institutions, their adaptability endures. Leaders, albeit constrained, retain the capacity to foster peace through visionary leadership and global cooperation. By acknowledging its limitations and fostering open dialogue, Liberal IR Theory continues to evolve, poised to contribute to a just and peaceful global order.

Agriculture contributes towards South African economy, but this sector is highly vulnerable to risks imposed by climate change. Smallholder maize farmers are specifically susceptible to climate change impacts. Maize crop plays a crucial role in the country's food security as it is considered a stable food for households and source of feed for livestock. The study aimed to analyze the socio-economic factors influencing smallholder maize farmers’ willingness to adopt climate-smart agriculture. It was conducted in three different areas due to their specific agro-ecological zones. Multipurpose research design was used to gather data, and multistage random sampling to choose the study areas. Subsequently, 209 purposively selected farmers were interviewed face-to-face using structured questionnaires and focus discussion groups. Descriptive statistics and Double-hurdle regression model were used to analyze the data. Descriptive results indicated that 81%, 67%, and 63% farmers were willing to adopt CSA in Ga-Makanye, Gabaza, and Giyani, respectively. Empirical results from the first and second hurdles of the regression analysis showed that farmers’ education, crop diversification, information about CSA positively influenced the decision to adopt CSA while household size and agricultural experience negatively influenced the decision to adopt CSA. It is recommended that the Department of Agriculture, Land Reform, and Rural Development should provide CSA workshops and educational programs to farmers to enhance their knowledge and decision-making processes regarding adaptation strategies.

This study introduces a Fiber Specklegram Sensor (FSS) design for temperature measurement utilizing a single-multi-single mode optical fiber configuration. FSS technology offers unique advantages for potential development into portable sensing systems. This investigation explores an FSS design compatible with miniaturization by optimizing the interrogation system based on the relationship between speckle grain size and filtering fiber area. Temperature variations are detected through fluctuations in optical power at the sensor output, offering a simple and reduced interrogation scheme. The performance of the FSS is assessed through post-calibration measurements compared to a commercial Fiber Bragg Grating (FBG) sensor, demonstrating comparable results. These findings pave the way for compact and portable fiber optic temperature sensing systems leveraging FSS advantages while maintaining compatibility with established fiber optic measurements.

The UK government and many international experts have pointed out that nuclear energy has an important role to play in the transition towards a decarbonized energy system since it is the only freely manageable very low-carbon energy technology with 24/7 availability to complement renewables. Besides current investments in light water reactor technologies, we need innovation for improved fuel usage and reduced waste creation, like offered by iMAGINE, for the required broad success of nuclear technologies. To allow quick progress into innovative technologies like iMAGINE and their regulation, a timely investment into urgently needed experimental infrastructure and expertise development will be required to assure the availability of capacities and capabilities. The initial steps to start the development of such a new reactor physics experimental facility to investigate molten salt fast reactor technology are discussed and a stepwise approach for the development of the experimental facility is described. The down selection to the choice for a diverse control and shutdown system is described through manipulating the reflector (control) and splitting the core (shutdown). The developed innovative core design of having the two core parts in two different rooms opens completely new opportunities and will allow to manifest the request for separated operational and experimental crews, as nowadays requested by regulators into the built environment. The proposed physical separation of safety relevant operational systems from the experimental room should on the one hand help to ease the access to the facility for visiting experimental specialists. On the other hand, the location of all safety relevant systems in a now separated access-controlled area for the operational team will limit the risk of misuse through third party access. The planned experimental programme described with the major steps: core criticality experiments, followed by experiments to determine the neutron flux, neutron spectrum, and power distribution as well as experiments to understand the effect of changes in reactivity and flux as a function of salt density, temperature and composition change.

There are thousands of rare genetic diseases that could be treated with classical gene therapy strategies such as the addition of the defective gene via viral or non-viral delivery or by direct gene editing. However, several genetic defects are too complex for these approaches. These “genomic mutations” include aneuploidies, intra and inter chromosomal rearrangements, large deletions, or inversion and copy number variations. Chromosome Transplantation (CT) refers to the precise substitution of an endogenous chromosome with an exogenous one. By the addition of an exogenous chromosome and the concomitant elimination of the endogenous one, every genetic defect, irrespective of its nature, could be resolved. In the current review, we analyze the state of the art of this technique and discuss its possible application to human pathology. CT might not be limited to the treatment of human diseases. By working on sex chromosomes, we showed that female cells can be obtained from male cells, since chromosome-transplanted cells can lose either sex chromosome, giving rise to 46,XY or 46,XX diploid cells, a modification that could be exploited to obtain female gametes from male cells. Moreover, CT could be used in veterinary biology, since entire chromosomes containing an advantageous locus could be transferred to animals of zootechnical interest without altering their specific genetic background and the need for long and complex interbreeding. CT could also be useful to rescue extinct species if only male cells were available. Finally, the generation of “synthetic” cells could be achieved by repeated CT into a recipient cell. CT is an additional tool for genetic modification of mammalian cells.

{This study investigates the coordinated behaviors and the underlying collective intelligence in biological groups, particularly those led by informed leaders. By establishing new convergence criteria based on real biological group experiments, this research introduces the concept of a volitional term and heterogeneous networks, constructing a coupled force Cucker-Smale model with informed leaders. The inclusion of the informed leader aspect distinctively characterizes the dynamics of leaders and followers, enabling a more accurate representation of biological group behavior. The paper then proposes the Flock Leadership Hierarchy Network (FLH), a model reflecting real biological interactions. By employing time slicing and rolling time windows, the study methodically analyses group behavior stages, using volatility and convergence time as metrics to examine the relationship between group consistency and interactions. Comparative experiments show the FLH network's superior performance. The Kolmogorov-Smirnov test indicates that the FLH network follows a power-law distribution, highlighting the evolutionary intelligence of biological groups. This research offers new perspectives on the evolution of biological groups, contributing to our understanding of both natural and artificial systems, such as animal migration and autonomous drone operations.

The Simulation analogy presented in this work enhances the accessibility of abstract quantum theories, specifically the stochastic hydrodyanimc model (SQHM), by relating them to our daily experiences. The SQHM incorporates the influence of fluctuating gravitational background, resembling dark energy, into quantum equations. This model successfully addresses key aspects of Objective-Collapse Theories, including resolving the 'tails' problem through the definition of quantum potential length in addition to the De Broglie length, beyond which coherent Schrödinger quantum behavior and wavefunction tails cannot be maintained. The SQHM emphasizes that an external environment is unnecessary, asserting that the quantum stochastic behavior leading to wave-function collapse can be an inherent property of a system in a spacetime with fluctuating metrics. Embedded in relativistic quantum mechanics, the theory establishes a coherent link between the uncertainty principle and the constancy of light speed, aligning seamlessly with finite information transmission speed. Within a fluctuating quantum system, the SQHM derives the indeterminacy relation between energy and time, offering insights into measurement processes impossible within a finite time interval in a truly quantum global system. Experimental validation is found in confirming the Lindemann constant for solid lattice melting points and the transition from fluid to superfluid states. The SQHM's self-consistency lies in its ability to describe wavefunction collapse and the measure process. Additionally, the theory resolves the Pre-existing Reality problem by showing that large-scale systems naturally decay into decoherent states stable in time. Continuing, the paper demonstrates that the physical dynamics of SQHM can be analogized to a computer simulation employing optimization procedures for realization. This perspective elucidates the concept of time in contemporary reality and enriches our comprehension of free will. The overall framework introduces an irreversible process impacting the manifestation of macroscopic reality at the present time, asserting that the multiverse exists solely in future states, with the past comprising the formed universe after the current moment. Decoherence at the present time functions as a reduction of the multiverse to a single universe. The macroscopic reality, characterized by fractal consistency where microscopic domains with quantum properties coexist, provides insights into how our consciousness apprehends dynamic reality, the spontaneous emergence of gravity in discrete spacetime evolution, and the attainment of the classical General Relativity limit in Quantum Loop Gravity and Causal Dynamical Triangulation. The Simulation Analogy highlights a strategy focused on minimizing information processing, facilitating the universal simulation in solving its predetermined problem. From within, reality becomes the manifestation of specific physical laws emerging from the inherent structure of the simulation devised to address its particular issue. In this context, the reality simulation appears to employ an entropic optimization strategy, minimizing information loss while efficiently compressing data in line with the simulation's intended purpose.

Background: After the increasingly common anterior cruciate ligament reconstruction (ACLR) procedure in competitive athletes, rehabilitation is crucial for facilitating a timely return to sports (RTS) and preventing re-injury. This pilot study investigates the biomechanical and psychological outcomes of postoperative rehabilitation in competitive athletes, comparing supervised rehabilita-tion (SVR) and home-based rehabilitation (HBR). Methods: After ACLR, 60 (out of 74 screened) athletes were recruited and equally divided into 2 groups using non-probability convenience sam-pling: 30 HBR and 30 SVR (each group comprising 15 males and 15 females). Rehabilitation out-comes in respective groups were evaluated at 8 months using measures (Tegner-Activity-Scale [TAS], International Knee Documentation Committee subjective knee form [IKDC-SKF], ACL Return to Sport after Injury [ACL-RSI]) and objective parameters (isometric muscle strength, hamstring/quadriceps asymmetry). RTS was evaluated at 9 months; with ACL re-injury rates rec-orded approximately 6 months post-RTS. Results: Both groups exhibited decreased TAS scores (HBR: 8 to 6, SVR: 8 to 7), with the SVR group demonstrating superior post-operative IKDC-SKF scores (81.82 vs. 68.43) and lower ACL-RSI scores (49.46 vs. 55.25). Isometric and isokinetic mus-cle strength, along with asymmetry values, favored the SVR group 8 months post-ACLR (p

Background: Feline infectious peritonitis (FIP) is a fatal feline disease classified as either effusive (‘wet’), non-effusive (‘dry’), or a mixture of both forms (‘mixed’). The anti-FIP therapeutic effect of Mutian and molnupiravir, two drugs whose active ingredient is a nucleic acid analog, has been confirmed recently. Methods: Of the cats with FIP, we observed a total of 122 and 56 cases achieved remission after administration of Mutian and molnupiravir as routine treatments, respectively. Changes in clinical indicators suggested to be correlated with FIP remission (weight, hematocrit, and albumin to globulin ratio) before and after the administration of each drug and during follow-up observation were statistically compared for each FIP type. Results: In all three FIP types, administration of either Mutian or molnupiravir resulted in statistically significant increases in these indicators. Furthermore, the effect of Mutian on improving the albumin to globulin ratio was not observed at all in wet FIP, as compared with that of molnupiravir, but statistically significant in mixed and dry (P<0.02 and P<0.003, respectively). These clinical features were all due to differences in fluctuations of circulating globulin levels. Conclusions: These results indicate slight inflammatory responses might be elicited continuously by residual feline coronavirus non-disappeared through molnupiravir treatments.

In the process of climate change mitigation and adaptation, the focus on climate risks driven by transition innovations has received widespread attention from governments, regulators and investors. Based on the identification of low-carbon patents through the Green and Low-carbon Technology Inventory in China, we construct low-carbon innovation measurements of listed firms in China from 2015 to 2021 then an empirical model is used to investigate the impact and mechanism of climate transition innovations on the default risk. The baseline regression model shows that low-carbon innovations can mitigate the default risk of firms. Moreover, our findings are supported by instrumental variable regressions that use time costs of innovation. In addition, the mediation effect demonstrates that investor attention, total factor productivity, and technology spillovers are paths for transition innovations to affect the default risk. This study reveals that low-carbon technological advances have a positive effect on climate transition risks. Further, it provides empirical evidence for listed companies to develop low-carbon innovations.

To satisfy the interests of multiple agents and those of comprehensive indicators such as peak-to-valley differences and load fluctuations occurring on the network side, this paper presents a flexible load demand-side response optimization method that considers the benefits of peak-to-valley smoothing. First, load aggregation modelling of air conditioning and electric vehicles was conducted, and the complementarity of the power consumption behaviour of different types of flexible loads was used to improve the responsiveness of the load aggregator. Second, considering demand-side responses and taking into account the interests of both supply and demand, the load fluctuation and peak-to-valley difference on the network side are reduced, and a flexible load double-layer optimization model incorporating the peak-to-valley smoothing benefit is established. Finally, the effectiveness of the proposed optimization model is verified by using the KKT condition and the big M method to evaluate this two-layer optimization problem as a single-layer optimization problem. Comparative examples demonstrate that the proposed two-layer optimization method can improve the revenue of the distribution network operators and the load aggregators by using the complementary nature of the load response characteristics of electric vehicles and air conditioners. Moreover, the proposed method can effectively reduce the load peak-to-valley difference and load fluctuation of the distribution network by introducing the peak-to-valley smoothing benefit model.

Silencing of the fragile X mental retardation 1 (FMR1) gene and consequently lack of synthesis of FMR protein (FMRP) are associated with fragile X syndrome, which is one of the most prevalent inherited intellectual disabilities. FMRP is a multifunctional protein involved in many cellular functions in nearly all subcellular compartments under normal conditions and under conditions of cellular stress in both neuronal and non-neuronal cell types. This is achieved through its trafficking signals, nuclear localization signal (NLS), nuclear export signal (NES), and nucleolar localization signal (NoLS), as well as its RNA and protein binding domains, and is modulated by various post-translational modifications such as phosphorylation, ubiquitination, sumoylation, and methylation. This review summarizes recent advances in understanding the interaction networks of FMRP with a special focus on FMRP stress-related functions, including stress granule formation, mitochondrion and endoplasmic reticulum plasticity, ribosome biogenesis, cell cycle control, and DNA damage response.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

The analysis of the key factors which prevent or contribute to the promotion and development of the Power Purchase Agreements (PPAs) in order to meet the sustainability goals represents an important issue which worth being investigated, especially in the situation in which entering in bilateral relations inside this contract has a powerful meaning in achieving new climate targets, developing and improving the use of green energy, and promoting a sustainable green economy. The main goal of this research is to identify and analyze the main factors which help or pre-vent the promotion and development of a PPA, in order to meet the sustainability goals by promoting a green economy. For this research survey based on comparative analysis, questionnaires and interviews with energy experts, Spearman’s correlation matrix and IBM SPSS Statistics for Window are also used. The results suggest that although there are positive interest and an open attitude towards the PPA from both sides (sellers and buyers), but there is still place for improvement, the lack of knowledge or the insufficient measures taken so far being two of the reasons way until now in Romania we do not have a developed PPA market and the level of knowledge regarding this type of mechanism is quite low.

Reactions of quinones with compounds containing an amino group can produce a wide variety of addition or substitution products that depend on reactivity of both quinone and amino derivative. 6,7-Dichloropyrido[1,2-a]benzimidazole-8,9-diones undergo selective nucleophilic substitution reaction with different benzohydrazides and α-hydroxy-p-quinone imine derivatives stabilized by strong intramolecular hydrogen bond were isolated. Synthesized compounds represent a combination of several structural motifs: benzimidazole core fused with α-hydroxy-p-quinone imine which contains a benzamido fragment. The protonation/deprotonation processes were investigated in a solution using UV-Vis spectroscopy and 1H NMR titration experiment. X-ray crystallography analysis revealed a set of weak non-covalent interactions such as intra- and intermolecular hydrogen bonds and π-π stacking. Additionally, the redox behavior of 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione and its p-imino derivative was investigated in acidic and neutral environment using cyclic voltammetry measurements. Cathode material based on 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione could act as potential effective active electrode in aqueous electrolyte batteries, however further optimization is required.

Abstract—Hydraulic switching actuators are high efficiency, fast response, and low cost solutions for hydraulic control systems. One of the challenging problems is throttling losses during valve transitions. Previously the authors proposed a zero-flowrate switching method to reduce throttling energy loss of the switching valve, where a hydraulic resonator is applied to make the flowrates through the lines approaching zero before the valves are switched off. The major challenge of this approach is fast switching valves whose transition times are less than 2 ms. In this paper, an improved zero-flowrate switching method is presented. It utilizes the capacity with independent inlet/outlet ports to regulate flowrates through the lines. Models of capacity applied in a simple line with different pressure signals are developed to explore characteristics of the capacity, based on which a complete actuation system is developed. In the complete model, resistance and inductance are optimized to achieve desired flowrate response. The improved zero-flowrate switching method reduces throttling energy losses by 99.945% compared to a hard switching system. The simulation results demonstrated that the improved zero-flowrate switching method performs as expected in the design condition. A capacity with proper volume is able to regulate flowrates through all the lines to zero, with the help of appropriate resistance and inductance. Compared to previous zero-flowrate switching method, the novel strategy allows slower switching valves applied in hydraulic actuation systems and achieves better efficiency performance. This research paves a new avenue for reducing throttling energy losses and improves system efficiency in hydraulic switching actuators, as well as most of the hydraulic switch-mode circuits.

Aim: To investigate inflammation indices and erythropoietin (EPO) levels for their potential role in distinguishing polycythemia vera (PV) from secondary polycythemia (SP), and to compare different parameter combinations in terms of diagnostic accuracy. Methods: This retrospective cohort was created from patients assessed for polycythemia from January 2020 to December 2023. PV diagnosis was made according to the 2016 WHO criteria (n=145). Those who did not fulfill the criteria were defined as having SP (n=84). Results: NLR, PLR and SII were significantly higher in the PV group (p

The benefits of cycling as a sustainable transportation mode are widely recognized. Cycling to work offers numerous advantages for individuals, employers, the environment, and society, ranging from improved physical health, wellbeing, and productivity to enhanced public health and reduced carbon emissions. Many governments around the world have implemented various policy measures, interventions, and initiatives to promote cycling. Some cities and towns have encouraged workplaces to provide bike-friendly amenities, such as secure bike parking/storage and shower and changing facility (referred to as end-of-trip facilities), to accommodate cyclists and motivate more employees to embrace sustainable transportation options. However, the presence or absence of such amenities has been found to both positively influence cycling behavior or deter some individuals from cycling to work. Despite the desirability of these amenities, the number of office buildings equipped with bike storage and shower/changing facility remains small, and their economic value is not well understood. In this paper, we aim to investigate whether the presence of cycling-supportive facilities could add value to office buildings. Specifically, we conduct a study using data from office buildings across England as of the end of 2021. We employ hedonic techniques to examine whether office buildings with bike storage and/or shower facility command a rent premium and whether the existence of a rent premium for bike storage and/or shower facility vary by location and across regions in England, independently from any premium associated with BREEM certification. We find that the buildings with bike storage and shower facility secure rent premiums respectively. The level of rent premiums varies with location and regions. The variations of premium are driven by the shortage of the supply of these facilities.

External hoof characteristics, balance, and conformation have been extensively studied in horses; however, mules remain understudied in these aspects. This study evaluated the size, shape, and symmetry of untrimmed and unshod forelimb hooves, compared the symmetry between forelimb hooves and stratified external forelimb hoof measurements based on the body condition score of mules raised in the foothill plains of northern Thailand. The forelimb hooves of 38 mules were photographed and 33 parameters, including angular and linear measurements, were analyzed. Despite the absence of shoeing and trimming, these mules exhibited optimal left-right forelimb hoof symmetry, with no significant (p < 0.05) differences in: outer wall length and inner wall length (OWL - IWL); sole length and sole width (SLS - SW); dorsal hoof wall length and heel length (DHWL - HL); and frog length and frog width (FL - FW). However, significant (p < 0.05) differences were observed within each body condition score group for forelimb hoof measurements for DHWL, IWL, heel separation (HS), heel bulb distance (HBD), SW, FW, and FL. These findings provide valuable insights into mule welfare and management, contributing to understanding of the interplay between overall health and hoof conformation in the study area.

The quest for surgical advancements regarding the enhancement of the submental and cervicofacial regions has witnessed a remarkable upsurge in recent years. Informed patients are actively seeking sophisticated plastic surgery techniques to achieve comprehensive rejuvenation in these specific areas. Common complaints expressed by these patients include sagging of the jawline, the emergence of deep perioral wrinkles, and the formation of "marionette lines" within the lower third of the face. Furthermore, the manifestation of age-related signs, including neck laxity, submental adipose accumulation, "witch's chin" deformity, and weakened platysma musculature, are common within this anatomical region. This literature review aims to summarize the recent technical improvements, historical evolution, indications, postoperative care, and challenges for facial rejuvenation of the lower third of the face and neck. Lastly, the application of minimally invasive procedures as part of a comprehensive approach to an aging face will also be discussed.

The global craft beer market is witnessing substantial growth, with a particular spotlight on sour beers. These unique brews are created through lactic fermentation initiated by lactic acid bacteria (LAB). However, the presence of hops, renowned for their antimicrobial properties, can pose a limitation within the realm of sour beer production. This research aims to explore and assess the potential of sour beer as a probiotic beverage. It involves a comparative analysis of the viability of Lacticaseibacillus paracasei subsp. paracasei F19 (F19) and 431 (L431) in a sour beer with an International Bitterness Unit (IBU) value of 26.65, alongside examining the ex-pression of genes such as horA, horB, horC, hitA, bsrA, and recA, which are associated with hop resistance. The study encompasses the development of two formulations of sour beers characterized by both high hop content and a robust probiotic count (8.44 – 8.77 log CFU/mL). The findings suggest that both probiotic strains of F19 and L431, are well-suited to produce sour beers with elevated hop levels, demonstrating excellent stability. Notably, the expression of genes responsible for hops resistance exhibited distinct modulation patterns among the two strains. It appears that a higher concentration of bsrA, as observed in strain L431, may be more effective in mitigating the effects of hop-related stress, potentially surpassing the combined expression of horA and bsrA. Nonetheless, further research is essential to validate this observation in gene expression. F19 and L431 emerge as promising candidates for the development of sour beers with increased hop intensity.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

The aim of the research was to determine the most productive tree cutting methods and the factors influencing them in flat and sloping terrain in tree plantations in Brazil. The study utilized drone-captured video material from eucalyptus and pine plantations harvesting operations. In both terrains, two cutting methods were compared, differing in the felling to the side method used: either at the edge of the harvesting front or inside. In addition, on flat terrain, the efficiency of forward felling was studied in relation to the aforementioned methods. In slope terrain, the machines were also equipped with a winch assistance system. Statistical tests were used to determine the most productive cutting methods by analyzing differences in productivity. With an average tree size of 0.3 m3, cutting productivity was 45 m3/E0h in pine cuttings and 55 m3/E0h in eucalyptus cuttings. The average cutting productivity on flat terrain was about 11 m3/E0h higher than on sloping terrain, mainly due to the time spent attaching the winch assistance system, which was a necessary phase of the work in sloping terrain. The research results suggest that it would be the most productive to use sideways felling inside the harvesting front method. However, the need for further research is evident if we want to precisely identify the harvesting conditions and work phases in the tree cutting cycle affecting the differences in the productivity of the harvesting chain in tree plantations.

Addressing non-unions involves stabilizing the affected area through osteosynthesis and improving bone biology using bone grafts. However, there is no consensus on the optimal treatment method. This study aims to compare outcomes of non-union revision using conventional treatment methods (metal hardware ± graft) versus osteosynthesis with the human, allogeneic cortical bone screw (Shark Screw®). Thirty-four patients underwent conventional treatment, while 28 cases received Shark Screws®. Patient demographics, bone healing, time to bone healing, and complications were assessed. Results revealed a healing rate of 96.4% for the Shark Screw® group, compared to 82.3% for the conventionally treated group. The Shark Screw® group exhibited a tendency for faster bone healing (9.4±3.2 vs. 12.9±8.5 weeks, p=0.05061). Hardware irritations led to six metal removals in the conventional group versus two in the Shark Screw® group. The Shark Screw® emerges as a promising option for personalized non-union treatment in the foot, ankle, and select lower leg cases, facilitating effective osteosynthesis and grafting within a single construct, promoting high union rates, low complications, and a rapid healing process.

The paper presents modelling of relationships between wind velocity distributions observed in Poland and technical requirements for wind power stations design. The wind velocities distributions for various locations in Poland are determined, and expressed in Weibull distribution parameters. Theoretical computations concerning the dependence of wind power station as function of wind speed and aire physical properties are presented. Conclusions important for design of power stations fitted to atmospheric conditions in Poland are given. Wind power plants have been an important source of electricity generation for many years.Wind power modelling with the use of wind speed is used to improve the accuracy of forecasts and analyses of the power production of wind farms.

The traditional approach of considering the probability distribution of rain attenuation leads to overdesign the power margin of data channels. We have first recalled a method, proposed in 2016, which with a small power margin, bandwidth expansion and variable symbol rate avoids overdesign and can transfer the same data volume as if the link were in clear–sky conditions. It is charaterized only by the link mean efficiency 0≤η≤1, suitably defined. It is usefull only if: (a) data must be downloaded also when it is raining; (b) real–time communication is not strictly required. We have applied it to the links of GeoSurf satellite constellations by simulating rain attenuation time series at 80 GHz (mm–wave) with the Synthetic Storm Technique, from rain-rate time series recorded on–site, at sites located in different climatic regions. The power margin to be implemented ranges from 2.0 dB to 7.4 dB – well within the current technology – regardless the instantaneous rain attenuation. The clear–sky bandwidth is expanded 1.75 to 2.80 times, not large per se, but it may challenge current technology if the clear–sky bandwidth is already large.

In the context of carbon neutrality and carbon peaking, in order to achieve low carbon emissions and promote the efficient utilization of wind energy, hydrogen energy as an important energy carrier is proposed to mix hydrogen and natural gas to form hydrogen enriched compressed natu-ral gas (HCNG). It is also injected into the natural gas pipeline network to realize the transmission and utilization of hydrogen energy. At the same time, the participation of demand response is considered, the load peak and trough period is adjusted, and large-scale consumption of renewa-ble energy and the reduction of carbon emissions are realized. First of all, a fine model of hydro-gen production and hydrogen use equipment is established to analyze the impact of adding hy-drogen mixing on the economy and low-carbon of the system. With green certificates and demand response, the utilization rate of hydrogen energy is improved to further explore the energy utiliza-tion rate and emission reduction capacity of the system. Secondly, on the basis of modeling, the optimal scheduling strategy is proposed with the sum of energy purchase cost, equipment opera-tion cost, carbon emission cost, wind curtailment cost and green certificate income as the lowest objective function. Considering the constraints such as hydrogen blending ratio and flexible load ratio of the pipeline network, a low-carbon economic scheduling model of hydrogen mixed natu-ral gas was established. The model was linearized and solved by using MATLAB and CPLEX solver. By comparing different scenarios, the superiority of the model and the effectiveness of the strategy are verified.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

Recently, Gohar et al. introduced a novel, local, and well-behaved fractional calculus. It possesses all the classical properties, and Its locality imposes simplicity and accuracy in modeling fractional order systems. In this article, we further develop the definitions and extend the classical properties of Gohar fractional calculus to address some of the open problems in Calculus. The fractional Gronwall's integral inequality, Taylor power series expansion, and Laplace transform are defined and applied to overcome some of the limitations in the classical integer-order calculus. The fractional Laplace transform is applied to solve Bernoulli-type logistic and Bertalanffy nonlinear fractional differential equations, and the criteria under which it can be applied to solve linear differential equations are investigated.

This article discusses how, in today’s world of disruptive and dramatic social change (DSC), non-sports related coaching, which includes a wide range of services such as life coaching, career coaching, executive coaching, and team coaching, can inadvertently fuel undesirable social dynamics. There is little or no awareness of this risk among coaches and coachees. The global, fast-growing, multi-billion-dollar industry aimed at supporting people and organisations to perform better and increase wellbeing while managing and adapting to change has been developed with limited sociological input. The article is based on 15 years of social constructionist-informed reflective practice by a sociologist-turned-coach, and uses a multi-layered autoethnographic account to argue for a sociologically informed paradigm shift in coaching, as well as relevant sociological knowledge and social and human sciences research methodology in coaches’ education. It presents the rationale and key features of a new coaching approach that places DSC-relevant sociological concepts at the heart of the coaching process, helps people develop psycho-sociological awareness, and uses a learning-to-develop through research design. A new definition of coaching to address DSC is derived. Coaching practitioners will find DSC-relevant sociological concepts, critical reflections, coaching questions, and procedures to expand coaching effectiveness. Interdisciplinary research topics combining coaching sociology and coaching psychology are suggested.