With the escalating water scarcity in agriculture, a novel water-saving technique has emerged: drip irrigation with plastic-film mulch (DI). Root function is crucial for sustaining rice production, and understanding its response to DI is essential. However, few studies have evaluated root systems in rice varietals and examined which kind of root system contributes to improving rice grain yield and water productivity in DI. To fill this knowledge gap, we conducted a two-year field experiment comparing two irrigation systems: continuous flooding (CF) and DI. We analyzed their effectiveness with four rice varieties, including upland, F1 lowland, animal feed lowland, and lowland varieties. Vertical root distribution, root bleed-ing rate, photosynthetic-associated parameters, water productivity, and yield performance were analyzed. In our study, the average grain yield of varieties in the DI system (6.4t/ha) was equivalent to those in the CF system (6.6 t/ha). Compared to CF, DI demonstrated significant water-saving potential, saving approximately 35% of the total water supplied, resulting in higher water productivity. Among the varieties, the deep-root weight of the upland variety significantly increased by 51%. The deep-root ratio was positively correlated to transpiration rate, grain yield, and water productivity, which suggested that it contributed to high transpiration, thus maintaining a high carbon assimilation rate resulting in high yield and water productivity. Therefore, deep roots deserve consideration as a trait potentially corresponding to high yield under DI.

PVC-based materials are bad in terms of biodegradability. To enhance the ecological property of such materials, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were obtained and study their optical, structural, thermal, and mechanical properties depending on the nature of the filler (spruce flour, birch flour, and rice husk) were studied. Increasing the proportion of plant filler somewhat reduces the strength characteristics and reduces the flexibility of the samples. But samples with plant filler allows them to be used at low temperatures without changing the operating characteristics. Some of the fillers affected the thermal stability of composites by increasing their thermal decomposition resistance. So, results have shown that plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compound for some applications such as construction.

The microbial colonisers of plastics – the ‘plastisphere’ – can affect all interactions that plastics have with their surrounding environments. While only specifically characterised within the last 10 years, at the beginning of 2021 there were 140 primary research and 65 review articles that investigate at least one aspect of the plastisphere. We gathered information on the locations and methodologies used by each of the primary research articles, highlighting several aspects of plastisphere research that remain understudied: (i) the non-bacterial plastisphere constituents; (ii) the mechanisms used to degrade plastics by marine isolates or communities; (iii) the capacity for plastisphere members to be pathogenic or carry antimicrobial resistance genes; and (iv) meta-OMIC characterisations of the plastisphere. We have also summarised the topics covered by the existing plastisphere review articles, identifying areas that have received less attention to date – most of which are in line with the areas that have fewer primary research articles. Therefore, in addition to providing an overview of some fundamental topics such as biodegradation and community assembly, we discuss the importance of eukaryotes in shaping the plastisphere, potential pathogens carried by plastics and the impact of the plastisphere on plastic transport and biogeochemical cycling. Finally, we summarise the future directions suggested by the reviews that we have evaluated and suggest other key research questions.

Plastic poses a significant threat to the environment, polluting land, water, and air. It is a broad term encompassing a variety of polymers. In the form of microplastics and nanoplastics, it can induce toxicity in water bodies. Plastic debris not only physically pollutes freshwater, but also chemically, undergoing changes over time due to hydroclimatic effects. Rivers serve as conduits, transporting plastics from minor tributaries to major rivers and ultimately into the ocean, endangering marine life. India, as a developing country with the largest population and numerous rivers, generates a significant amount of plastic waste, a substantial portion of which finds its way into rivers, leading to alarming rates of plastic accumulation in the ocean. Previously, policymakers focused primarily on landfills for plastic waste, neglecting the pollution of water bodies. The consequences of this neglect are evident, with major rivers in the country severely affected by plastic waste, necessitating advanced, efficient, and sustainable solutions. This study aims to establish a comprehensive framework for managing plastic waste, understanding its transport mechanisms to the ocean, and recognizing the threats it poses to life. It also expounds on harmful plastic pollutants in water, globally adopted technologies, and emphasizes the need for further research and data collection in this field. The primary concluding point is to prevent plastics from entering waterways and to actively collect river and marine plastic pollution. Banning single-use plastics and implementing efficient collection methods are crucial in containing plastic pollution. Effluents from industries should not be overlooked, as they often contain harmful micro and nanoplastics with ecotoxicological effects. The innovative concept of the "4Rs" - Refuse, Reduce, Reuse, and Recycle - stands as the cornerstone for safeguarding the environment against plastic pollution.

Fossil-based plastics are significant contributors to global warming through CO₂ emissions. For more sustainable alternatives to be successful, it is important to ensure that consumers become aware of the benefits of innovations such as bio-based plastics, in order to create demand and a willingness to initially pay more. Given that consumer attitudes and (inaccurate) beliefs can influence the uptake such new technologies, we investigated participants’ attitudes towards fossil-based and bio-based plastic, their perceived importance of recycling both types of plastic, their willingness to pay, and their perceptions of bio-based plastic in four studies (total N = 961). The pre-registered fourth study experimentally manipulated information about bio-based plastic and measured willingness to pay for different types of plastic. The results suggest participants hold very favourable attitudes and are willing to pay more for bio-based products. However, they also harbour misconceptions, especially overestimating bio-based plastic’s biodegradability, and they find it less important to recycle bio-based than fossil-based plastic. Study 4 provided evidence that educating consumers about the properties of bio-based plastic can dispel misconceptions, retain a favourable attitude and a high willingness to pay. We found mixed evidence for the effect of attitudes on willingness to pay, suggesting other psychological factors may also play a role. We discuss how attitudes and misconceptions affect the uptake of new sustainable technologies such as bio-based plastics and consumers’ willingness to purchase them.

Despite good intentions, the increasing number of plastic bag bans aimed at alleviating marine plastic pollution saw a correlated increase in the number of unintended consequences that emerged alongside the bans, suggesting that human behavior towards plastic bag consumption have not changed, but merely shifted, and are feeding into other major international environmental catastrophes. Nudge theory, which helps people make better choices for themselves without inhibiting their free will, is a potential solution that has been shown to play a subtle but important role in providing options under circumstances where complex information needs to be streamlined for the wider community, avoiding any unintended consequences and behavioural shifts that might arise from instruments that diminishes autonomy. It is therefore timely to look into the insights of nudge theory to encourage a positive behavioural change to reduce plastic bag consumption. Here we apply a systematic literature review to show how successful applications of nudges in supermarkets can be leveraged to reduce plastic bag consumption. We find that the current applications of nudges in various industries worldwide, including supermarkets have produced positive and encouraging results, as well as producing lasting behavioural change among the wider community. Supermarkets are identified as a powerful deployment site of these nudges due to their positioning as a dominant provider of plastic bags to the wider community, as well as being the largest and leading provider of daily food needs. Finally, we synthesise our findings to produce a coherent and testable framework of actionable interventions that supermarkets can employ to nudge customers towards reduced plastic bag reliance, accompanied with a visual timeline of a customer shopping in a supermarket experiencing these nudges.

The surface planarity and asperity removal behaviors of atomic scale under the ultrathin water environment was studied for the nanoscale process by molecular dynamics simulation. The monolayer atomic removal was achieved under the noncontact and monoatomic layer contact conditions with different water film thickness, and the newly formed surface is relatively smooth and no deformed layer and plastic defects exist. The nanoscale processing is governed by the interatomic adhering action during which the water film transmits the loading forces to Cu surface and thereby result in the migration and removal of surface atoms. With scratching depth ≥ 0.5 nm, the abrasive particle squeezed out the water film from scratching region and scratched Cu surface directly, leading to the surface quality deterioration mainly governed by the plowing action. This study brings the goals of “0 nm planarity, 0 residual defects and 0 polishing pressure” closer to us in the nanoscale process for the development of ultra-precision manufacture technology.

Abstract: The ongoing use of plastic polymers to manufacture food packaging has raised concerns about the presence of nano- and microplastics (NMPs) in a variety of foods. This review provides the most recent data on NMPs' migration from plastic packaging into milk and dairy products. Also discussed are the possible effects of NMPs on nutrient digestion, absorption, and metabolism. Different kinds of milk products, including skimmed or whole liquid and powder milk, infant formula milk, and other dairy products, have been found to contain NMPs of various sizes, shapes, and concentrations. NMPs may interact with proteins, carbohydrates, and fats and have a detrimental impact on how well these nutrients are digested and absorbed by the body. The presence of NMPs in the gastrointestinal tract may impact how lipids, proteins, glucose, iron, and energy are metabolised, increasing the risk of developing health conditions such as diabetes, cardiovascular disease, hypertension, and some cancers. In addition to NMP, plastic oligomers released from food packaging material have been found to migrate to various food simulants and milk, though their effect on human health has yet to be investigated. Viewpoints on potential directions for future studies on NMPs and nutrient digestion, absorption, and health are also presented in this review.

This letter attempts to clarify an issue regarding the proper definition of plastic dislocation density tensor. This study shows that the Ortiz’s and Berdichevsky’s plastic dislocation density tensor are equivalent with each other, but not with Kondo’s one. To fix the problem, we propose a modified version of Kondo’s plastic dislocation density tensor.

Microplastics and nanoplastics (MP/NPs) have been found everywhere they have been searched. On the top of Everest, in the Mariana Trench, on the clouds e recently, microplastics have been discovered in the human placenta, meconium and babies’ feces. In this review we explain what the consequences of the presence of these pollutants in fetuses and newborns are, with particular attention to human breastfeeding. Finally, we outline the possible political and social solutions to the problem of plastic overproduction that characterizes the modern world.

The paper presents a conceptual model of the route of macroplastic debris (5 > mm) through a fluvial system, which can support future works on the overlooked processes of macroplastic storage and remobilization in rivers. We divided the macroplastic route into (1) input, (2) transport, (3) storage, (4) remobilization and (5) output phases. Phase 1 is mainly controlled by humans, phases 2–4 by fluvial processes, and phase 5 by both types of controls. We hypothesize that natural characteristics of fluvial systems and their modification by dam reservoirs and flood embankments construction are key controls on macroplastic storage and remobilization in rivers. The zone of macroplastic storage can be defined as a river floodplain inundated since the beginning of widespread disposal of plastic waste to the environment in the 1960s and remobilization zone as a part of the storage zone influenced by floodwaters and bank erosion. The amount of macroplastic in both zones can be estimated using data on the abundance of surface- and subsurface-stored macroplastic and the lateral and vertical extent of the zones. Our model creates the framework for estimation of how much plastic has accumulated in rivers and will be present in future riverscapes.

A tumbler screen type residual film–impurity mixture wind separator as a key equipment for secondary utilization of farmland residual film. During the working process, the proportion of impurities in the separated waste mulch film intermittently increases, resulting in poor working stability of the device, which may hamper long-term operation. In this study, the material inside the separation unit was continuously monitored, and the main factor affecting separator per-formance was determined to be the challenges in the effective depolymerization of some residual film–impurity mixtures. The principles of agglomeration and depolymerization of the residual film–impurity mixtures were analyzed using computational fluid dynamics (CFD) and discrete element method (DEM) flow-solid coupling simulation methods. The key factor affecting the disaggregation of the mixture was the collision force between the residual film–impurity mixture and the trommel screen. The collision force was maximum when the residual film–impurity mixture first collided with the trommel screen when it was fed into the separation device. As determined by force analyses, the key factors affecting the collision force of the process were the material feeding amount and the structure of the inlet. Furthermore, simulations were carried out for different inlet structure forms; the evaluation index was the maximum collision force of the residual film–impurity mixture agglomerate on the trommel screen. The best disaggregation effect was obtained with a square feed inlet and at a feeding rate of 202 kg/h. A prototype was built using these specifications for verification. The average value of the ratio of impurities in the re-sidual film was 6.966%, the coefficient of variation was 7.38%, and the dispersion of statistical results was small. The ratio of impurities in the residual film was kept constant during the con-tinuous operation of the wind separator. Thus, this study analyzed the agglomerate disaggregation process and provided theoretical insights for deter-mining the optimal structures of the inlets of various cleaning devices and the feeding volumes.

Optical and mechanical properties of multilayer coatings depend on the selected layer materials and the deposition technology; therefore, knowledge of the performances of thin films is essential. In the present work, titanium dioxide (TiO2) and silicon dioxide (SiO2) thin films have been prepared by plasma ion-assisted deposition (PIAD). The optical, structural, and mechanical properties of thin films have been investigated using spectrometer/ellipsometer, X-ray diffraction (XRD), atomic force microscopy (AFM), and laser interferometer. The results show that TiO2 film fabricated by PIAD induces a high refractive index, wide optical band gap, amorphous structure, smooth surface, and tensile stress. In the case of SiO2 film, high bias voltage leads to dense structure and compressive stress. As an application, a three-wavelength high reflectance at 632.8, 808, and 1550nm is optimized and deposited. The dependence of total stress in the multilayer on the substrate temperature is studied as well. In conclusion, it is demonstrated that PIAD is an effective method for the preparation of ultralow stress TiO2/SiO2 multilayer films. The achieved stress is as low as 1.4Mpa. The result could provide guidance to the stress optimization of most optical components without prefiguring, backside coating, and post-deposition treatments.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

Giant unilamellar vesicles (GUVs) are membrane model used to study membrane properties. Electroformation is one of the methods used to produce GUVs. During electroformation protocol dry lipid film is formed. Drying of the lipid film induce Cholesterol (Chol) demixing artifact, in which Chol forms anhydrous crystals, where these crystals does not participate in formation of vesicles. This leads to a lower Chol concentration in the vesicle bilayers compared to the Chol concentration in the initial lipid solution. To address this problem, we propose novel electroformation protocol that includes rapid solvent exchange, plasma cleaning and spin-coating methods to produce GUVs. We tested the protocol focusing on vesicles with high Chol content using different spin-coating durations and vesicle types deposition. Additionally, we compared the novel protocol using completely dry lipid film. The optimal spin-coating duration for vesicles made out of phosphatidylcholine/Chol mixture was 30 s. Mulitlamellar vesicles (MLVs), large unilamellar vesicles (LUVs) obtained by extrusion of MLVs through 100 nm membrane pores and LUVs obtained by extrusion of previously obtained LUVs through 50 nm membrane pores were deposited on electrode for 1.5/1 Chol/phosphatidylcholine lipid mixture and the results were compared. Electroformation using all three deposited vesicle types gave a high GUVs yield, but deposition of LUVs obtained by extrusion of MLVs through 100 nm membrane pores gave the most reproducible results. Using deposition of these LUVs, we produced GUVs with high yield for 6 different Chol concentrations (from 0 % to 71.4%). Using protocol that includes dry lipid film GUVs yield was lower and Chol demixing artifact was induced, proving that the lipid film should never undergo drying when Chol content is high.

A new biodegradable paper-based film is a hot research topic in the development of green agriculture. In this paper, a black paper base film coated with cooked tung oil with excellent mechanical properties, hydrophobic surface, high heat transfer and strong weather resistance was prepared by spraying high pigment carbon black solution on the surface of base paper. The results showed that the surface solidified oil film with rough structure was made by the brush coating process of cooked tung oil, and the base film of black paper was given hydrophobic structure, and the contact angle reached 98.9 °. Cooked tung oil permeates into the inside of the paper base, and after curing, it forms a multi-dimensional network film structure. The maximum tensile stress of the black paper base film is about 123% higher than that of the original paper base film. The coloring of carbon black makes the black paper base film have heat conduction effect, and the average heat transfer rate reaches 15.12 °C/s. Cooked tung oil is combined with the paper-based fiber high-toughness layer to form a stable system. The existence of the cured film improves the basic mechanics and hydrophobicity, and the resistance to ultraviolet radiation and hot air is greatly improved. This study provides a feasible scheme for the application of a black paper base film coated with cooked tung oil.

Water management and soil pollution are hot issues in modern agriculture. While more production of food is required, this quantity has to be obtained using the minimum level of resources and the maximum amortization of assets. Moreover, studies show that in Europe, 30% of water consumption is for agriculture, which has a strong influence not only on the amount of water consumed, but also on its quality due to pollution caused by chemical fertilizers, pesticides and other pollutants used in this sector. Therefore, a major concern is related to the use of water, its efficient consumption, which requires optimal irrigation systems both in terms of water transport and distribution. In this context, but also in the context of a turbid environmental debate, the most important facts in agriculture are the protection of the environment on a long range of time. In order to obtain good results for an irrigation system, in this paper we will present a model for calculating the best suited material for a given geographical area and the optimal water content for irrigation

The rapid development in industries manufacturing plastic bags is taking serious consideration to save the environment and human health, one way or the other. This study examines the composition of degradable and non-degradable plastic bags collected from the markets of different sectors of Islamabad. Hundred samples of both Degradable and non-degradable plastic bags were collected from the open market. The concentrations, proportion, and patterns of different heavy metals (additives) were used in the production of both degradable and non-degradable plastic bags by using the standard method with the help of Hands Held X-Ray Fluorescent (HHXRF) instrument. Samples results of the study showed Titanium, Calcium and Copper used in massive amounts, some of the toxic metals i.e., Arsenic, Lead, Cadmium, Chromium and Mercury were also detected. This study also reveals that degradable plastic bags might be more hazardous than non-degradable plastic bags because due to the Photolytic properties of additives used in degradable plastic bags when the chains of polymers break, the heavy metals are released in environment and become the part of it. So, concern department like Ministry of climate change and Pakistan Environmental Protection Agency should take serious step to control these serious issues.

HDPE (high-density polyethene) plastic waste is stronger, harder, and more resistant to high temperatures than other plastics. Using it as an additive in a concrete mixture is one solution to reduce this type of waste. We examined how HDPE-type plastics can be used as an additive material in the manufacture of concrete to improve its hardness, tensile strength and compressive strength. Using 156 samples, we aimed to identify the effect of HDPE plastic fibres on concrete of three qualities; B0, f'c10 MPa (low quality), and f'c25 MPa (medium and high quality). We added four compositions (2.5%, 5%, 10% and 20% by weight of cement) of HDPE plastic fibre to each quality of cement, with HDPE plastic fibre sizes of 1 x 1 cm, 0.5 x 2 cm or 0.25 x 4 cm. We found that the addition of 5% HDPE plastic fibre with a 0.5 x 2 cm cross-sectional shape to the f'c10 MPa concrete gives the best result, with increased tensile and compressive strength of the concrete.

The influence of the film thickness and the substrate’s refractive index on the surface mode at the superstrate is an important study step that may help clearing some of the misunderstandings surrounding their propagation mechanism. A single sub-wavelength slit perforating a thin metallic film is among the simplest nanostructure capable of launching Surface Plasmon Polaritons on its surrounding surface when excited by an incident field. Here, the impact of the substrate and the film thickness on surface waves is investigated. When the thickness of the film is comparable to its skin depth, SPP waves from the substrate penetrate the film and emerge from the superstrate, creating a superposition of two SPP waves, that leads to a beat interference envelope with well-defined loci which are the function of both the drive frequency and the dielectric constant of the substrate/superstrate. As the film thickness is reduced to the SPP’s penetration depth, surface waves from optically denser dielectric/metal interface would dominate, leading to volume plasmons that propagate inside the film at optical frequencies. Interference of periodic volume charge density with the incident field over the film creates charge bundles that are periodic in space and time.

A Cu₂ZnSnS₄ (CZTS) film with a thickness of approximately 1.5 μm was fabricated on a Mo-coated glass substrate by annealing a CZTS precursor fabricated from nanoparticle ink. The chemical states of the elements in the CZTS thin film in the depth direction were studied to identify the presence of secondary phases, which are detrimental to the performance of solar cells containing CZTS. X-ray diffraction was unable to detect any secondary phases in CZTS because of their small relative amount. Instead, X-ray photoelectron spectroscopy (XPS), which is highly sensitive to chemical state, was conducted at different depths in the CZTS film to further check the presence of secondary phases. XPS analysis revealed peaks shift consistent with the presence of secondary phases. For the CZTS film annealed in a S atmosphere at 575 °C for 3 h, the film surface consisted of a secondary-phase layer composed of CuS, ZnS, and SnSx (x=1 or 2) originating from the decomposition of CZTS. At depths below 80 nm, the film was pure CZTS. Formation of MoS2 at the CZTS–Mo interface was confirmed by XPS analysis of Mo and S.

The Western ‘discovery’ of Japanese cinema in the 1950s prompted scholars to articulate essentialist visions understanding its singularities as a result of its isolation from the rest of the World and its close links to local aesthetic and philosophical traditions. Recent approaches however, have evidenced the limitations of this paradigm of ‘national cinema’. Higson (1989) opened a critical discussion on the existing consumption, text andproduction-based approaches to this concept. This article draws on Higson´s contribution and calls into question traditional theorising of Japanese film as a national cinema. Contradictions are illustrated by assessing the other side of the ‘discovery’ of Japanese cinema: certain gendaigeki works that succeeded at the domestic box office while jidaigeki burst into European film festivals. The Taiyōzoku and subsequent Mukokuseki Action created a new postwar iconography by adapting codes of representation from Hollywood youth and western films. This article does not attempt to deny the uniqueness of this film culture, but rather seeks to highlight the need to reformulate the paradigm of national cinema in the Japanese case, and illustrate the sense in which it was created from outside, failing to recognise its reach transnational intertextuality.

Online artificial intelligence (AI) tools have recently gained in popularity. So-called “generative AI” chatbots unlock new opportunities to access vast realms of knowledge when being prompted by users. Here, we test the capabilities of two such AIs in order to determine the benefits for plastic surgery while also assessing potential risks. Future developments are outlined. We used the online portals of OpenAI’s ChatGPT(version 3.5) and Google’s Bard to ask a set of questions and give specific commands. Results provided by the two tools were compared and analyzed by a committee. For professional plastic surgeons, we found that ChatGPT and Bard can be of help when it comes to conducting scientific reviews and helping with scientific writing but are of limited use due to the superficiality of their answers in specific domains. For medical students, in addition to the above, they provide useful educational material with respect to surgical methods and exam preparation. For patients, they can help when it comes to preparing for an intervention, weighing in risks and benefits, while providing guidance on optimal post-operative care. ChatGPT and Bard open widely accessible data to every internet user. While they might create a sense of “magic” due to their chatbot interfaces, they nonetheless can help to increase productivity. For professional surgeons, they produce superficial answers - for now - albeit providing help with scientific writing and literature reviews. For medical students, they are great tools to deepen their knowledge about specific topics such as surgical methods and exam preparation. For patients, they can help in translating complicated medical jargon into understandable lingo and provide support for pre-operative as well as post-operative care. Such AI tools should be used cautiously as answers are not always precise nor accurate and should always be used in combination with expert medical guidance.

Polyurethane (PU) is a polymer widely used by humans whose recycling is highly complex due his chemical structure, being limited to incineration or accumulation in landfills. Biodegradation by enzymes and microorganisms has been studied for decades as an effective method of biological decomposition. In this study, Tenebrio molitor larvae (T. molitor) were fed with polyurethane foams, which gut enzymes and microorganisms were capable of degrading the polymer by 35% in 17 days of treatment, producing a weight loss of 14% in the mealworm. Changes in T. molitor gut bacterial community and diversity were observed, which may be due to colonization of species associated with PU degradation. Physical and structural biodegradation in PU by T. molitor compared to virgin PU, was demonstrated by Fourier Transform InfraRed spectroscopy (FTIR), Thermal Gravimetric Analysis (TGA) and Scanning Electron Microphotography (SEM).

Enhancement in the strength of austenitic steels with a small content of carbon can be achieved by a limited number of methods, among which is the ultrafine-grained (UFG) structure formation, especially efficient with the use of severe plastic deformation (SPD) processing that enables increasing significantly the contribution of grain-boundary strengthening, and also involves a combination of other strengthening factors (work hardening, twins, etc.). In this paper, we demonstrate that the use of SPD processing combined with conventional methods of deformation treatment of metals, such as rolling, may lead to an additional strengthening of UFG steel. Analysis of the results of the study on the change of the microstructure and mechanical properties of the Cr-Ni stainless austenitic steel after a combined deformation reveals a substantial increase in the strength properties of this steel, resulting from a consecutive application of SPD processing via equal-channel angular pressing and rolling at a temperature of 400 С, yielding a strength more than 1.5 times higher that that produced by any of these two methods used separately.

It is widely accepted that plastic waste is one of our most urgent environmental concerns the world is currently facing. Plastic has contributed greatly to innovation in all fields, but the raw material for its production (fossil fuels), as well as the linear economy in which it is currently produced and used, makes the material problematic from a sustainability and human health perspectives. The emergence of bio-based plastics provides an opportunity to reduce dependency on fossil fuels and transition to a more circular plastics economy. For polyethylene terephthalate (PET), one of the most prevalent plastics in packaging and textiles, there exist two bio-based alternatives that are similar or superior in material property and recyclability. These are polyethylene furanoate (PEF) and polytrimethylene terephthalate (PTT). The overarching aim of this study was to examine the transition from fossil-based to renewable plastics, through the lens of PET upcycling into PEF and PTT. The process for the production of PEF and PTT from three feed streams (post-consumer PET waste, lignocellulosic biomass-derived cellulose and biodiesel-derived crude glycerol) was developed in the software SuperPro Designer and the economic viability assessed via a discounted cumulative cash flow (DCCF) analysis. This study represents a conceptual case study of the valorisation of existing plastic waste into new, recyclable bio-based plastics, for a more sustainable plastics production. A techno-economic analysis of the designed process revealed that the minimum selling price (MSP) of second generation-derived PEF and PTT is 3.13 USD/kg, and that utilities and the feedstock used for the production of 2,5-furandicarboxylic acid (FDCA) needed in PEF synthesis contributed the most to the process operating costs. The effect of recycling PEF and PTT through the process at three recycling rates (42%, 50% and 55%) was investigated and revealed that increased recycling could reduce the MSP of the 2G bio-plastics (by 48.5%) to 1.61 USD/kg. This demonstrates that increasing recycling rates would have a beneficial effect on the economic viability of the plastic biorefinery.

The crack geometry and associated strain field around Berkovich and Vickers indents on silicon have been studied by X-ray diffraction imaging and micro-Raman spectroscopy scanning. The techniques are complementary, the Raman data coming from within a few micrometers of the indentation, whereas the X-ray image probes the strain field at a distance of typically tens of micrometers. For example, Raman data provides an explanation for the central contrast feature in the X-ray images of an indent. Strain relaxation from breakout and high temperature annealing are examined and it is demonstrated that millimeter length cracks, similar to those produced by mechanical damage from misaligned handling tools, can be generated in a controlled fashion by indentation within 75 micrometers of the bevel edge of 200mm diameter wafers.

The effects of the coolant pulsation and the film cooling with the plasma aerodynamic actuation (PAA) could be herein explored via large eddy simulations. The electrohydrodynamic force derived from the PAA was solved through the phenomenological plasma model. The Strouhal number of the sinusoidal coolant pulsation and the averaged pulsation blowing ratio were 0.25 and 1.0, respectively. Comprehensive analyses were carried out on the time-averaged flow fields, and the results revealed that the pulsed cooling jet might cause a deeper penetration into the crossflow, and this phenomenon could be remarkably mitigated by the downward force of the PAA. Furthermore, because of the coolant pulsation, the counter rotating vortex pair (CRVP) expanded to lifted off the wall less well, and the PAA lessened the negative lift-off impact and entrapment from the CRVP. Then, the spatial-temporal development of the coherent structures was figured out by the alterations of the centerline temperature, reflecting formation of the intermittent coherent structures rather than hairpin vortices due to the coolant pulsation, and their size and upcast behaviors were reduced by the PAA. Consequently, there was a basic suppression of the turbulent mixing of the cooling fluid with the crossflow. Finally, the three-dimensional streamlines confirmed that the coherent structure dynamic behaviors were significantly regulated by the PAA for alleviating the adverse influences of the coolant pulsation. In summary, through controlling how the dominating coherent structures evolve throughout time and space, the PAA can effectively increase the pulsed film cooling efficiency.

We investigated layered titanium nitride (TiN) and aluminum nitride (AlN) for color glasses in Building Integrated Photovoltaic (BIPV) systems. AlN and TiN are among suitable and cost-effective optical materials to be used as thin multilayer films, owing to the significant difference in their refractive index. To fabricate the structure, we used radio frequency magnetron deposition method to achieve the target thickness uniformly. A simple, fast, and cheap fabrication method is achieved by depositing the multilayer films in a single sputtering chamber. It is demonstrated that a multilayer stack that allows light to move from a low refractive index layer to a high refractive index layer or vice-versa can effectively create various distinct color reflections for different film thicknesses and multilayer structures. It is investigated from simulation based on wave optics that, TiN/AlN multilayer offers better color design freedom and cheaper fabrication process as compared to AlN/TiN multilayer films. Blue, green, and yellow color glasses with optical transmittance of more than 80% was achieved by ITO coated glass/TiN/AlN multilayer films. This technology exhibits good potential in commercial BIPV system applications.

Abstract: The expansion of global industries results in the release of harmful volatile acid vapors into the environment, posing a threat to various life forms. Hence, it's crucial to prioritize the development of swift sensing systems capable of monitoring these volatile acid vapors. This initiative holds great importance in safeguarding a clean and safe environment. This paper presents the synthesis and characterization of pyrene-based covalent organic frameworks (COFs) demonstrating exceptional crystallinity, thermal stability, and intense fluorescence. Three COFs—PP-COF, PT-COF, and PE-COF—were synthesized, showcasing large surface areas and robust thermal stability up to 400 °C. The fluorescence properties and intramolecular charge transfer within these COFs were significantly influenced by their Schiff base bonding types and π-stacking degrees between COF layers. Notably, PE-COF emerged as the most fluorescent among the three COFs and exhibited exceptional sensitivity and rapid response as a fluorescent chemosensor for detecting HCl in solution. The reversible protonation of imine bonds in these COFs allowed for the creation of highly sensitive acid vapor sensors, showcasing a shift in spectral absorption while maintaining structural integrity. This research highlights the potential of COFs as reliable and reusable sensors for detecting harmful acid vapors, addressing environmental concerns arising from industrial activities.

ZnO thin films with a thickness of 300 nm were deposited on Si and Al2O3 substrates using electron beam evaporation technique with the aim to be tested as low cost and low power consumption gas sensors for ozone (O3). To characterize the surface roughness and the grain size, which are the main parameters recognized to enhance gas sensitivity since they directly influence the effective sensing area, surface morphology and roughness analyses of the films were performed using scanning electron microscopy and atomic force microscopy, respectively. The crystalline structure and elemental composition were studied through Raman spectroscopy and X-ray photoelectron spectroscopy. Gas tests were conducted at room temperature and zero-bias voltage to assess the sensitivity and response as a function of time of the films to O3 pollutant. The results indicate that the films deposited on Al2O3 exhibit promising characteristics, such as high sensitivity and a very short response time (< 2 s) to the gas concentration. Additionally, it was observed that the films display pronounced degradation effects after a significant exposure to O3.

Biodegradable and renewable plastic films have been regarded as promising alternative green materials to achieve the substitution polythene (PE)films to reduce plastic pollution. Poly (butylene adipate-co-terephthalate) (PBAT) is a kind of biodegradable polyester, which is widely used in the production of biodegradable mulching films. However, the high cost of PBAT limited it applications. Thus, lignin, one of the most abundant biomass resources was incorporated into PBAT matrix in the present work. A series of Lignin/PBAT biodegradable plastics films with different Lignin/PBAT weight ratios (0.00 %-5.00 %) were successfully fabricated using twin screw and twin roll extruders. The chemical compositions, morphologies, thermal stabilities, mechanical properties, and barrier properties of samples were characterized by XRD, FTIR, TG/DSC, mechanical testing machine, and WVTR, respectively. Results show that the corporation of lignin into PBAT matrix could lead to improved thermal stabilities, mechanical properties and barrier properties of films even after Xenon lamp aging process, especially when Lignin/PBAT weight ratio is 1.00 % in the present work. This work provides a very promising approach for fabrication of biodegradable plastics films with low cost, enhanced mechanical properties and barrier properties, the as-prepared samples may have potential applications in agricultural or food packaging materials.

Film therapy, the therapeutic use of movies in psychological therapies, is a growing area of interest to therapists and researchers. This paper presents the MOVIE model of film therapy, a widely applicable, trauma-informed framework for working with film imagery and themes in individual or group therapy, counsellor education and self-help. Film or cinema therapy is a highly accessible and relatable method for many diverse client and student groups with benefits that include, catharsis and emotional processing, greater ease of dialogue around issues, increased empathy, and interpersonal learning, engaging with new perspectives and learning skills. Following the model clients mindfully observe and voice their emotional and psychological responses to movie watching, identify how the imagery, characters, themes, and narrative symbolise personal experience and consider any new possibilities that emerged through re-authoring personal narratives. The model is informed by a practice focused review of literature.

We demonstrate a concept and fabrication of lithography-free layered metal-\ce{SiO2} thin-film structures which have reduced reflectivity (black appearance), to as low as 0.9~\%, with 4.9~\% broadband reflectance (8.9~\% for soda lime) in the 500 - 1400~nm range. The multi-layered (four layers) thin-film metamaterial is designed so that optical impedance matching produces minimal reflectance and transmittance within the visible and infra-red (IR) spectral region for a range of incident angles. The structure has enhanced absorbance and is easily tuned for reduced minimal transmission and reflection.

The main aim of this work is to report an alternative energy efficient technique of fabricating flexible thermoelectric generators (TEGs) using printable ink. In this process, we have fabricated thermoelectric (TE) composite thick film and we are experimenting several ways to overcome the challenges of conventional and additive manufacturing methods. Two different mesh sizes of n-type bismuth particle, various binder to thermoelectric (TE) material weight ratio, and two different pressure (200 MPa and 300 MPa) were employed for optimizing the thermoelectric properties of TE composite films. We are also exploring naturally occurring chitosan as a binder. Dimethyl sulfoxide (DMSO) dissolved chitosan was used for the binder and less than 0.2 wt% of chitosan was sufficient for the fabrication of TE inks and composite films. Low energy intensive curing process was employed to evaporate the solvent from the drop casted inks. External uniaxial pressure not only eliminated high energy intensive curing processes but also increased the packing density of the film by removing pores and voids in the chitosan-bismuth composite film. The microstructure analysis reveals that bulk-like structure, which rarely has voids, pores and grain boundaries, was observed in the composite films pressed at sufficiently high pressures. The highest performing composite film was obtained with the conditions of 1:2000 binder to bismuth weight ratio, 100 mesh of particle size, and 300 MPa of pressure. The best performing bismuth chitosan composite film pressed at 300 MPa had the power factor as 4009 ± 391 μW/m·K² with high electrical conductivity value of 7337 ± 522 S/cm. The measured thermal conductivity of the best performing chitosan-bismuth composite film was 4.4 ± 0.7 W/m·K and the figure of merit calculated from the thermal conductivity was 0.27 at room temperature.

Effects of plastic deformation on the indentation feature of hot-rolled commercial pure titanium alloy were detected using microindentation. It was found that the most deformed sample experienced the largest indentation resistance and had the maximum dislocation density and the indentation size influenced the CP-Ti indentation feature. The Vicker hardness and energy dissipated demonstrated the significant influence of the dislocation motion and size effects on the indentation in the indentation deformation. The linear relation of the energy ratio which is related to the microstructures and the indentation depth ratio was obtained for hcp materials Titanium alloys.

Cosmetic surgery is the subfield of plastic surgery that enhances appearance mainly for aesthetic reasons. Currently, cosmetic surgery interventions are highly considered appealing and popular all around the world. Several factors have contributed in this rapidly evolving field such as scientific and economic development, breaking down barriers and cultural norms, globalization, social media and mental disorders. Nowadays, the morality of cosmetic surgery is facing many dilemmas due to its benefits and drawbacks. It is proven that the advantages of cosmetic surgery include improved body confidence, mental health, and function. Additionally, aesthetic corrections can upscale the quality of life and create career opportunities for special targeted groups. Also, cosmetic surgery has a major impact in gender affirmation procedures. Although, herein we also describe the disadvantages of this widely developing field such as minor and major medical complications, potential postoperative risks and addiction in plastic surgeries associated with damaging economic issues. Lack in self-confidence, altered mental health status and ethical crisis consist another negative aspects of aesthetic surgery’s impact.

Monitoring and maintenance of cracked structures are generally done using structural integrity assessments. The plastic zone (PZ) crack path (CP) criteria state that a crack grows in the direction when the radius of the plastic zone ahead of the crack tip reaches a minimum value. The PZ can be evaluated using Stress intensity factors (SIF). The SIFs under mixed-mode loading were extracted from literature from three samples: two SENT samples made from polycarbonate and one modified C(T) sample made from low-carbon steel. In addition, the CP angle was evaluated for the W and R-criteria. It was found that both can predict the CP for lateral cracks in both tested materials and monotonic and cyclic load when the mode-mixity does not change considerably from one crack length to the next one or goes beyond 0.2. Moreover, the R-criterion exhibited an error as high as 1.7%, whereas the W-criterion showed a 6% error on the last crack length for the low carbon steel sample under cyclic load, which had a 100% increase in mode-mixity. Finally, the applicability of LEFM is checked, while the CP is sought by finding the size of the PZ.

Abstract. The paper presents primary material on determining the presence of micro- and macroplastics in Markakol Lake, one of the high-mountainous and unique water bodies of Kazakhstan, conditionally undisturbed, but vulnerable to anthropogenic pollution. In the course of work, micro- and macroplastics were detected in all selected samples in the water area of the lake and its main tributaries, the Urunkhaika, Topolevka, Tikhushka, Matabai, Elovka rivers. When determining micro- and macroplastics, we were guided by the method of analysis in aquatic environment, NOAA research program, developed by American scientists Masura J. et al, which is used in many countries. Concentrations and sizes of MP found in the water of the main tributaries of the rivers Urunhaika in concentrations up to 211.4 µg/m3, Tikhushka – 97.9 µg/m3, Zhirelka – 67.8 µg/m3, Topolevka – 157.2 µg/m3, Matabai – 78.3 µg/m3. Concentrations of MP in the surface water layer of the lake detected during 15 minute trawling at distances from 438 m to 841 m occur in sieve mesh sizes of 1.0 mm – 316.7 µg/m3 and 0.315 mm – 520.8 µg/m3. The total concentration of detected micro- and macroplastics coming with tributaries was – 150 µg/m3, in the lake water area – 837.4 µg/m3. The sizes of plastic debris found both in river waters and along the lake water area ranged from mesoplastic debris (fishing line net fragments, foam balls, plastic bags, plastic bottles, wrappers, food labels and packaging, etc.) to microplastic particles detected using a microscope with 40X magnification in size ranges of 25 mm, 1.0 mm and 0.315 mm. Sources of MP depend on local human activities (fishing, transportation, waste disposal etc.).

In this paper, we propose a modeling method based on peridynamics for ductile fracture at high temperatures. A thermoelastic coupling model combining peridynamics and classical continuum mechanics is used to limit the peridynamics calculations to the failure region of a given structure, thereby reducing computational costs. Then, a plastic constitutive model of peridynamic bonds is developed to capture the ductile-fracture process of the structure. Furthermore, an iterative algorithm for ductile-fracture calculation is presented. Finally, several numerical examples are shown. Particularly, the fracture processes of a superalloy structure under 800℃ and 900℃ environments are simulated and compared with experimental results. Our comparisons show that the crack modes captured by the proposed model are similar to experimental observations, which verifies the validity of the proposed model.

Excessive production, consumption and indiscriminate disposal of plastic waste cause an increasing plastic pollution with detrimental impacts on environment and human health. This study aimed to assess the level of knowledge, attitude, and practices (KAP) towards plastic pollution among Malaysians and evaluate the variation of plastic pollution related KAP among various socio-demographics. An online survey was conducted, and 294 valid responses was obtained. Descriptive statistics, KAP scoring and cross tabulation of responses were estimated. One-way analysis of variance, paired t-test and binary logistic regressions were carried out. Results showed that respondents had poor knowledge (mean 7.41 ± 1.80) and practice score (3.81 ± 1.39) across all socio-demographics. Compared to younger (18-30 years) respondents, older ones (>46 years) had higher knowledge (odds ratio, OR 4.304; p<0.01). However, middle aged (31-45 years) respondents reported significantly (p<0.01) higher attitude (OR 4.019) and practice (OR 4.056; p <0.05). Respondents with environmental related university education had showed higher odds about plastic pollution related knowledge (OR 10.343; p<0.01). Suggestions are made to undertake interventions such as environmental awareness creation, incorporating plastic pollution topics in formal and informal education, and providing recycling facilities nearby the localities for encouraging good practices towards minimizing plastic uses and pollution.

The present study was aimed to evaluate the suitability of agro-wastes and crude vegetable oils for the cost effective production of poly-β-hydroxybutyrate (PHB), to evaluate growth kinetics and PHB production in Alcaligenes faecalis RZS4 and Pseudomonas sp. RZS1 with these carbon substrates and to study the biodegradation of PHB accumulated by these cultures. Alcaligenes faecalis RZS4 and Pseudomonas sp. RZS1 accumulate higher amounts of PHB corn (79.90% of dry cell mass) and rice straw (66.22% of dry cell mass) medium respectively. The kinetic model suggests that the Pseudomonas sp. RZS1 follows the Monod model more closely than A. faecalis RZS4. Both the cultures degrade their own PHB extract under the influence of PHB depolymerase. Corn waste and rice straw appear as the best and cost-effective substrates for the sustainable production of PHB from Alcaligenes faecalis RZS4 and Pseudomonas sp. RZS1. The biopolymer accumulated by these organisms is biodegradable in nature. The agro-wastes and crude vegetable oils are good and low cost sources of nutrients for the growth and production of PHN and other metabolites. Their use would lower the production cost of PHN and the low cost production will reduce the sailing price of PHB based products. This would promote the large scale commercialization and popularization of PHB as ecofriendly bioplastic/biopolymer.

In this paper, an incremental eqivalent contact model is developed for elastic-perfectly plastic solids with rough surfaces. The contact of rough surface is modeled by the accumulation of circular contacts with varying radius, which is estimated from the geometrical contact area and the number of contact patches. For three typical rough surfaces with various mechanical properties, the present model gives accurate predictions of the load-area relation, which are verified by direct finite element simulations. An approximately linear load-area relation is observed for elastic-plastic contact up to a large contact fraction of 15%, and the influence of yield stress is addressed.

Astola Island is the first marine protected area of Pakistan acknowledged 2017, June 15. It is a rich biodiversity hotspot, Ramsar site inhabiting endangered species like Green turtle, Hawksbill turtle, and Arabian Humpback whale. A saw-scaled Russell’s viper is endemic to Island. Marine ecology of Astola Island is affected by plastic pollution resulting in coral destruction, ocean acidification, global warming, fishing nets blockage, water pollution, and coastal erosion. Zeolite catalyst synthesized from environmentally friendly way by coal fly ash to degrade collected plastic waste from Island into useful products in pyrolysis reactor. The synthesized catalyst functionalized further with three type of organosilane(1) Octyltriethoxysilane(OS),(2)Phenyltriethoxysilane(PS)(3)Vinyltriethoxysilane(VS).Zeolite functionalize with octyltriethoxy silane (ZO) shows the highest performance in plastic pyrolysis, resulting in lower degradation temperature, low residue and more product formation may be due to having long chain hydrocarbon and acidic sites. Plastic recycling is the promising solution to tackle plastic blooming issue. Which is negatively impacting all the compartments of ecosystem especially marine environment.

Demolished concrete and plastic waste are two increasingly aggravating problems. In this study, a novel method was proposed to simultaneously recycle concrete and plastic wastes by compacting concrete and plastic powders together under pressure and temperature. The influence of compression pressure and temperature as well as the mixture proportion on the bending strength of specimens was investigated. The results showed that pressure and temperature had a positive effect on the specimen strength; however, the molding temperature should not exceed the melting temperature of plastic. The proportion of plastic had a minimal effect on the bending strength of the specimen when plastic accounted for 25%–75% of the overall mass of the test piece.

Plastics are naturally hydrophobic materials so, in order to employ flotation for the separation of plastic mixtures, the use of appropriate wetting agents is mandatory. In this work, the effect of pretreatment with alkaline solutions of sodium hydroxide on the floatability of four plastics (PET, PS, PMMA and PVC) was studied. The influence of NaOH concentration, treatment time and temperature of the alkaline solution, and influence of particle size was analyzed. Results showed that alkaline treatment had a strong effect on PET floatability, some effect on floatability of PMMA and PVC and no effect on floatability of PS. Plastics floatability decreased with the increase of NaOH concentration, temperature and treatment time of the alkaline solution. Based on flotation behavior of simple plastics, flotation separation after alkaline treatment of bi-component mixtures of PET with PS and PVC was achieved efficiently. The best separation was obtained for PET/PS mixture, a floated with a grade of 98% in PS and a sunk with a grade of 100% in PET. PET/PMMA mixture led to the worst separation. For PET/PMMA and PET/PVC mixtures, flotation separation improved with the decrease of the particles size.

To extend the calculation power of tensor analysis, we introduce four new definition of tensor calculations. Some useful tensor identities have been proved. We demonstrate the application of the tensor identities in continuum mechanics: momentum conservation law and deformation superposition.

This paper is the second part of a two-part report studying the responses of a typical point-contact elastohydrodynamic lubrication (EHL) problem to multiscale roughness that is mimicked by artificially generated waviness with different amplitudes, frequencies, and directions. The previous Part I paper (doi:10.3390/lubricants10120368) focuses on the full film regime, while the current paper focuses on the partial film regime. The amplitudes and frequencies are related to the feature geometry of smooth EHL problems. Generated waviness is input to a transient thermal EHL model. The simulation is conducted 1,600 times for different waviness parameters, loads, and speeds. Eight performance parameters are extracted: the asperity contact ratio, minimum film thickness, maximum pressure, central point film thickness, central point pressure, mean film thickness, coefficient of friction (COF), and the maximum temperature rise. The ratios of the first seven parameters with and without waviness and the asperity contact ratio values are plotted on the frequency–amplitude coordinate plane as contour maps. The influences of the amplitude, frequency, wave direction, load, and speed on the eight performance parameters are analyzed and summarized. The simulated data and plotted contour maps are provided to the readers in the Supplementary Material.

Organic electrochemical transistors (OECTs) based on conducting polymers have attracted significant attention in the field of biosensors. PEDOT:PSS and polyaniline (PANI) are representative conducting polymers used for OECTs. While there are many studies on PEDOT:PSS, there are not so many reports on PANI-based OECTs, and a detailed study to compare these two polymers has been desired. In this study, we investigated the fabrication conditions to produce the best performance in the OECTs using the above-mentioned two types of conducting polymers. Two main parameters were film thickness and film surface roughness. For PEDOT:PSS, the optimal conditions for fabricating thin films were a spin-coating rate of 3000 rpm and DI water immersion time of 18 hours. For PANI, the optimal conditions were a spin-coating rate of 3000 rpm and DI water immersion time of 5 seconds, and adding dodecylbenzenesulfonic acid (DBSA) was found to provide better OECT performances. The OECT performances based on PEDOT:PSS were superior to those based on PANI in terms of conductivity and transconductance, but PANI showed excellence in terms of film thickness and surface smoothness, leading to the good reproducibility of OECT performances.

The corrosion resistance of two cast CoCr based alloys, with different amounts of chromium and with different alloying elements in the bulk composition of the alloy, was assessed. Herewith, we investigated the corrosion behavior of Co21Cr8Mo7W and Co29Cr7W by open circuit potential (OCP), potentiodynamic polarization (PP) and electrochemical impedance spectroscopy (EIS) in 0.1 M phosphate buffer solution (PBS) at 37°C for long time immersion. After 1000 hours of immersion, the corrosion current density (icor), estimated from anodic polarization tests, is lower for Co21Cr8Mo7W (i.e. 49 nA cm-2) alloy compared to Co29Cr7W alloy (180 nA cm-2). As regards the corrosion potential (Ecor), a nobler value was observed for Co21Cr8Mo7W (i.e. -59 mV vs. Ag/AgCl) compared to Co29Cr7W (i.e. -114 mV vs. Ag/AgCl). These findings suggest a better corrosion resistance of the film formed on the alloy containing lower amount of Cr and two alloying elements, namely Mo and W. These results are promising ones in terms of medical applications because they open new strategies in obtaining alloys with lower content of chromium and with higher protective properties against corrosion attack.

Iron, a crucial element in our environment, plays a vital role in numerous natural processes. Understanding the presence and concentration of iron in the environment is very important, as it impacts various aspects of our planet’s health. On-site detection and speciation of iron are significant for several reasons. In this context, the present work aims to evaluate the applicability of voltammetry for on-site determination of iron and its possible speciation using a portable voltammetric analyzer. Voltammetry offers the advantage of convenience and cost-effectiveness. For iron (III) determination a modification of a glassy carbon electrode (GCE) with an antimony-bismuth film (SbBiFE) using acetate buffer (pH=4) as supporting electrolyte was used. The technique adopted was Square Wave Adsoptive Cathodic Stripping Voltammetry (SW-AdCSV) and we used 1-(2-piridylazo)-2-naphthol (PAN) as iron (III) ligand. Linearity, repeatability, detection limit and accuracy were determined using synthetic solutions, then a Standard Reference Material (SRM) 1643f - Trace Elements in Water was used for validation measurements in real matrix. The procedure was finally applied to real samples (tap, lake and sea water) and the results obtained were compared by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). The results obtained demonstrated the excellent applicability of the proposed on-site voltammetric procedure for the determination of iron and its speciation in water.

In response to the problem of no supporting equipment for the cultivation of Codonopsis in the hilly and mountainous areas of northwest China, a combined machine for transplanting outcrop of Codonopsis with micro ridge covered with film is designed. The key components of the prototype are analyzed and designed, and the structures and working parameters of the seedbed preparation device, seedling casting device, rotary tillage soil-covering device, film covering device, seedling head burial and film edge soil-covering device are determined. The transmission system scheme is established, and the working mechanism of the core components is analyzed. Field experiments show that when the target seedling spacing is 4.4cm and the machines moves forward at the speed of 0.1, 0.15, and 0.2m/s, the variation coefficient of planting spacing and the qualification rate of planting depth all meet the standard requirements. The qualified rate of planting posture and film side outcrop are greatly affected by the operating speed of the machine, and decrease with the increase of operating speed. When the operating speed reaches 0.1m/s, the average variation coefficient of planting spacing is 0.08%, the average qualified rate of planting depth, planting posture and film side outcrop is 95.83%, 94.17% and 93.33% respectively, which shows that the operating performance is better than that of the operating speed of 0.15m/s and 0.2m/s. This study provides new reference for the theoretical research and design of mechanized and automated transplanting machinery for Codonopsis seedlings.

COVID-19 infection, caused by SARS-CoV-2, is inequitably distributed and more lethal among populations with lower socioeconomic status. Direct contact with contaminated surfaces has been one of the virus sources, as it remains infective up to days. Several disinfectants have been shown to inactivate SARS-CoV-2 but they rapidly evaporate, are flammable or toxic and may be scarce or inexistent for the vulnerable populations. Therefore, we are proposing a simple, easy to prepare, low-cost and efficient antiviral films, made with wide available dishwasher detergent, which can be spread in hands and inanimate surfaces and maintains virucidal activity for longer periods than the current sanitizers. Avian coronavirus (ACoV) was used as model of challenge to test the antivirus efficacy of proposed films. Polystyrene microplates were covered with a thin layer of detergent formula. After drying, the films were exposed to different virus doses for 10 minutes and virus infectivity were determined using embryonated chicken eggs and RNA virus quantification in allantoic fluids by RT-qPCR. The films showed to inactive the ACoV (ranging from 103.66 to 106.66 EID50), which is chemically and morphologically similar to SARSCoV-2 and may constitute an excellent alternative to minimize the spread of Covid-19.

Subwavelength hole array (HA) metasurfaces support the so-called extraordinary optical transmission (EOT) resonance that has already been exploited for sensing. In this work, we demonstrate the superior performance of a different resonant regime of HA metasurfaces called anomalous EOT, by doing a thorough numerical and experimental study of its ability as a thin-film label-free sensor in the terahertz (THz) band. A comprehensive analysis using both the regular and anomalous EOT resonances is done by depositing thin layers of a dielectric analyte of different thicknesses on the structures in different scenarios. We carry out a detailed comparison and demonstrate that the best sensing performance is achieved when the structure operates in the anomalous EOT resonance and the analyte is deposited on the non-patterned side, improving by a factor between 2 and 3 the results of the EOT resonance in any of the considered scenarios. This can be explained by the comparatively narrower linewidth of the anomalous EOT resonance. The results presented expand the reach of subwavelength hole arrays for sensing applications by considering the anomalous EOT regime that is usually overlooked in the literature.

Gas membrane-based separation is considered one of the furthermost effective technology to address energy efficiency and large footprint challenges. Various classes of advanced materials including polymers, zeolites, porous carbons and metal–organic frameworks (MOFs) were attempted as membranes for gas separation. MOFs, among other porous materials, possess uniquely tunable nature, in which the pore size and environment can be controlled by connecting metal ions (or metal ion clusters) with organic linkers with various functionalities. This feature makes them attractive for thin membrane fabrication, as both diffusion and solubility components of permeability can be altered. It is interesting to notice that numerous reports have addressed the synthesis of different MOFs, fabrication of their corresponding thin films and their applications, nonetheless, relatively limited studies addressed their gas separation application as membranes. In this review, we provide a synopsis of the various MOF-based membranes that were fabricated in the last decade. In this review we propose a short introduction touching on the gas separation membrane technology and we shed light on (i) the various techniques developed for the fabrication of MOF as membranes and (ii) challenges and application for MOF thin film membranes in various important gas separation applications.

This research presents a novel approach to film analysis, leveraging word vectors to objectively evaluate movie critiques. Focusing on Director Chanwook Park’s award-winning film, ’Decision to Leave’, the study employs word vectors derived from the movie’s script of Korean text. Traditional critiques often emphasize contrasting elements and themes, but their subjective nature poses challenges in objective validation. To address this, we trained a language model using LSTM on the film’s script, obtaining word vectors that capture the essence of the narrative. These vectors were then used to perform various text analyses, including similarity and analogy operation for the keywords suggested by the critiques. By comparing the semantic relationships in the critiques with those derived from the word vectors, we could objectively validate the critiques’ assertions. Furthermore, we visualized the word vectors in a two-dimensional space, confirming the spatial relationships of key terms highlighted in critiques. The study underscores the potential of word vectors in providing a more objective lens for film analysis, bridging the gap between traditional film criticism and data-driven insights.

Every year since the last fifty years, the world is waking up to higher and higher average temperature of the earth. Initially it was thought that this trend is a part of cyclical warming and cooling of the earth and nothing to be much worried about. However, with weather conditions become erratic and unusual over a large swath of the planet more and more frequently and regularly, scientists started to speak of Climate Change and people started to listen. In this paper we briefly discuss the link between global warming, climate change and current policies in the developing world to drive home the urgent need for alternative thinking. We briefly discuss the theoretical link between economic development and greenhouse gas emission and lay the micro foundation of the Environmental Kuznets Curve (EKC) before providing some evidence of global climate change and why this is a matter of concern for social scientists. Then we explore two avenues through which human activities are aggravating the situation especially in developing countries – the role of business architecture and the role of built architecture. We argue that these twin architecture are aggravating global warming by moving away from sustainable development policies.

Conventional methods for pathogen detection in water rely on time-consuming enrichment steps followed by biochemical identification strategies, which require assay times ranging from 24 hours to up to a week. However, in recent years, significant efforts have been made towards the development of biosensing technologies enabling rapid and close-to-real-time detection of waterborne pathogens. In previous studies, we developed a plastic optical fiber (POF) immunosensor using an optoelectronic configuration consisting of a U-Shape probe connected to an LED and a photodetector. Bacterial detection was evaluated with the immunosensor immersed in a bacterial suspension in water with a known concentration. Here, we report on the sensitivity of a new optoelectronic configuration consisting of two POF U-Shape probes, one as the reference and the other as the immunosensor, for the detection of Escherichia coli. In addition, another way of detection was tested where the sensors were calibrated in the air, before immersed in bacterial suspension and then read in the air, making the immunosensor more sensitive and with a faster detection time. This new sensor detected the presence of E. coli at 104 CFU/mL in less than 10 minutes. Currently sub 10 minutes is faster than previous studies using fiber-optic based biosensors. It is also a much simpler and quicker methodology when compared with conventional laboratory technology.

Agroforestry systems with multipurpose tree species, for the double production of timber and fruit, along with the intercropping with herbaceous crops, can be fundamental land use systems for multiple ecosystems services. Research was conducted in Italy, for one growing season, in 18 years old agroforestry experimental plots with common walnut (Juglans regia L.) trees, according to the previous agroforestry management (AFM) since tree planting. The aim is i) estimating trees growth and herbaceous yield in relation to increasing tree size, especially referring to the trees basal area (G); ii) evaluating the role of nut production as additional product to timber and food crops. Observations were run on tree growth and leaf phenology, total light transmittance (TTL) below tree canopy and hay yield with and without walnut intercropping. Nut yield was estimated from available literature and associated to G. At the end of the study year, representing two third of trees rotation, their height varied between 10 and 11 m, with much larger variation for tree diameter between 17 and 22 cm, according to the previous AFM, including tree mulching with plastic film. Hay yield varied between 4.5 and 3 Mg ha year-1 outside and under tree canopy, respectively. Negative regression were determined for G and TTL, and G and hay yield, with an annual reduction of 5% per G unit. Simulations were run on hay and nut yield, using G as main input parameter. The work points out the following key findings: i) the usefulness of plastic mulching, at tree planting, to increase the long-term timber productivity of the trees intercropped with herbaceous crops; ii) the negative linear relationship between hay productivity and walnut trees G; iii) G influences, in positive way, more markedly nut than hay yield. Suggestions are given on the optimum tree planting spacing and AFM for balancing timber, nut and hay yields.

Co-Zr amorphous alloys exhibit soft magnetic properties, whereas Co-rich crystalline magnetic phases in this alloy system display hard magnetic behaviour. In this study, an initial two-phase Co-Zr composite with an overall composition of 75 at.% Co and 25 at.% Zr was processed by high pressure torsion (HPT) and the effects of severe plastic deformation and subsequent thermal treatment on the structural evolution and its magnetic properties have been investigated. HPT processing allowed us to achieve an amorphous microstructure in the as-deformed state with low coercivity. To further tune magnetic properties and study the alloys’ crystallization behaviour, various annealed states are investigated. Microstructural properties are correlated to the magnetic properties and a decreasing coercivity with increasing annealing temperature is observed despite the onset of crystallization in the amorphous alloy. At higher annealing temperatures, coercivity increases again. The results appear promising to obtain tuneable rare-earth free magnetic materials by severe plastic deformation.

The reconstructive ladder is a well-established concept in Plastic Surgery proposed to achieve wound closure using a stepladder approach from simple to complex procedures and it continues to evolve from when it was presented for the first time. We describe a new surgical technique that allows skin excision and primary wound closure avoiding donor site morbidity from skin grafts and avoiding large scars from loco-regional flaps: the parallelogram excision technique. Fifteen patients with skin lesions underwent this procedure. Six months' follow-up results showed a) good scar healing, b) total excision of lesions, and c) patient acceptance and satisfaction from the usage of this technique. We conducted a geometrical analysis of the parallelogram’s design to study the optimal geometrical condition to achieve all these three factors. We propose that the parallelogram excision of skin lesions proves to be a unique new wound closure technique that may add a new rung to the reconstructive ladder.

Despite the increase in popularity of Zero Waste (ZW) concept, the successful implementation of this concept in waste management is still facing many challenges. The plastic recycling rate in Australia is currently only about 9.4%, which could leave up to 90.6% of plastic consumption being sent to landfills. The state of Victoria (in Australia) has proposed an ambitious plan to upgrade its waste and recycling system and to divert about 80% of waste from landfills by 2030. The aim of this research is to study Victoria’s current waste management plan and to develop a simulation model to assess the feasibility of it achieving zero plastic waste by 2035. In this direction, a fundamental knowledge of global ZW implementation needs to be acquired in order to understand the challenges, obstacles, and uncertainties in achieving ZW target. A simulation model is established using a method called double baselines. This method was developed as an improvisation to address the limitation of data availability for the model development. The model will run on 4 scenarios including one from Victoria’s current plan. Outcomes from the model are produced in comparative charts covering 6 key considerations including the rates of plastic consumption, waste to landfill, diversion, recycling, relative accumulative cost and effort. The findings of this study pointed out that Victoria’s current plan are feasible for its goal and presented with opportunities for improvement especially towards zero plastic waste. Besides, study results also reveal that the Victoria’s current plan to achieve 80% diversion rate by 2030 is possible but the zero plastic waste target by 2035 is less likely to happen.

Greenhouse have to provide optimal climate conditions for healthy plant growth and high production. Heating of greenhouses is required for an efficient and reliable production specially during winter time in Turkey. However, even in the temperate zones, heating costs has a great portion in the total production costs. Coal is preferred as a fuel in the greenhouse heating in provinces of Turkey where there is no geothermal energy. In this study, the heating requirements and fuel cost (fossil and geothermal energy) for Antalya, Afyon, Kütahya, Denizli, and Aydın provinces in the Aegean and Mediterranean region have been identified based on long term meteorological data. The calculations were made for two model greenhouses located in an area with 1 ha representing modern greenhouses of the regions. The first is a gothic roofed plastic model greenhouse and the second is a gable roofed polycarbonate model greenhouse. According to the results of calculations, total annual heatingrequirement values ranged from 6,096,283 (for Antalya) to 20,359,946 MJ/ha (for Afyon) for the plastic greenhouse wheras these values ranged from 3,187,074 (for Antalya) to 10,643,972 MJ/ha (for Afyon) for the polycarbonate greenhouse.

The evolution of metals micro/nano-structure upon severe plastic deformation (SPD) is still far to be theoretically explained, while experimental datasets are persistently growing for several decades. Major problem associated with understanding of SPD is related to a fact that the latter is a synergetic product of several competing physical effects which alter the material micro/nano-structure. In attempt to find deformational boundaries, where predominantly one mechanism determines the micro/nano-structure, in this paper we propose a continuous piecewise model for the analysis of experiments on material hardness vs strain of SPD processed materials. The novelty of this approach lies in its ability to find, as free-fitting parameters, the strain breakpoints which separate different micro/nano-structure modes generated upon SPD process. The model is applied to analyse experimental data for polycrystalline samples of pure iron and two distinctive strain breakpoints are revealed with good accuracies. This finding is in a good agreement with our earlier results on TEM microscopy studies on pure iron polycrystals after SPD treatment.

Metal matrix composite are used in such fields of technology, such as: aerospace, electronics, energy, industry, defense, automotive, aviation, shipbuilding, and more. Composite coatings of ceramic - metals is used primarily to enhance the durability of machine parts. Therefore, new materials are permanently looked for, what has resulted in the past in development of composite materials. The coatings dispersed are consisting of metallic matrix (metals and their alloys) and small non-metallic particles. The deposition of ceramic particles simultaneously with metallic matrix leads often to composite coatings possessing properties much better than those of metallic coating. The nickel and less often, other iron group elements are usually used as a matrix and Al2O3 as tough particles. The welding technology of applying alloy and composite coatings is widely used. The technology of infrasound thermal spraying of metal matrix composite coatings was presented. It is a simple technology and a very useful one in ship machinery regeneration during the cruise craft (e.g. internal combustion engines, torque pumps, separators). The metal matrix composite coatings must undergo finishing due to high surface roughness after application. In the article to used finishing by plastic working and machining of coatings nickel matrix composite was proposed.

Microorganisms drive the biogeochemical cycles that link abiotic and biotic processes in the aqueous environment and are intricately associated with plastic debris. The detection of microplastics in water and sediment introduces new concerns as small particle size allows for yet unconsidered pathways for plastics in the food web and element cycles. In this review, we present current knowledge of microbe-plastic interactions and summarize the potential impact of biogeochemical processes on plastic distribution, cycling, transport, and sedimentation. We explore how microbe-plastic interactions influence the exposure of consumers to plastics and plastic degradation products. Key methods used to elucidate biofilm development, microbial biodegradation, and plastic detection in the aqueous environment are discussed. Finally, we comment on potential future questions and research directions needed to further define the role of microorganisms in the environmental fate of microplastics.

The recyclability of polystyrene, acrylonitrile butadiene styrene, polystyrene and polyvinylchloride waste and using them as a source for 3D printing were studied. Filaments of about 3 mm in diameter were extruded successfully with a small-size extruder. The processed filaments were tested on a broad range of parameters - glass transition temperature, tensile properties and a pyrolysis scenario were obtained. The measured parameters were compared with parameters of virgin counterparts presented in the literature. In order to estimate the toxicity of the recycled material, elemental analysis of the samples was done.

1) Background: The objective was to evaluate the corrosion resistance of different commercially pure ultrafine-grained (UFG) titanium and its alloys with acid etched surface processed by equal-channel angular pressing (ECAP); 2) Methods: Coarse-grained and UFG titanium samples were investigated using polarization resistance technique. Surface characteristics of the native oxidized layer were evaluated by TEM and XRD. Electrochemical tests were under physiological electrolyte at a rate of 1 and 10 mV/s. Weight loss tests were performed after immersion into HCl solution for up to 3 years; 3) Results: UFG titanium was less susceptible to corrosion which was identified under lower rates and at higher polarization resistance than its coarse grain counterparts. Titanium Grade 2 and Grade 4 demonstrated similar corrosion susceptibility. Titanium Grade 5 revealed a thin and tightly adhered native oxide layer with adequate corrosion resistance; 4) Conclusions: ECAP process imposed a more compact and adhered oxidized layer. Surface etching techniques delivered a thicker native TiO₂ layer, being both grain refinement and surface etching techniques responsible for the improved corrosion resistance of Titanium samples under physiological environment after 3 years of observation.

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

The objective of this work is to identify the mechanism of dropwise condensation on a smooth solid surface. We investigate the stable dropwise condensation that occurs at a droplet growth rate of 1 µm/s in diameter on a gold-coated glass surface. Additionally, we present our observations on unstable dropwise condensation, i.e., degradation of dropwise condensation of steam on a gold surface. The Surface Plasmon Resonance Imaging (SPRi) approach used in this study has lateral resolutions of 4-10 µm, thickness resolutions of 0.1-1 nm, and temporal resolutions of 200-10,000 frames per second (FPS). SPRi is used to evaluate the existence and structure of thin films and occurrence of initial nuclei during condensation. Visualization of the onset of stable dropwise condensation suggests droplets form at heterogeneous nucleation sites and that no film greater than a monolayer exists on the surface before the formation of droplets. Observation of the unstable dropwise condensation of steam shows the existence of water films that are several nanometers thick between droplets. This work shows that neither the nucleation theory or film rupture theory can individually explain the physics of dropwise condensation. Therefore, there is a need for a more comprehensive theory that can explain the mechanism of dropwise condensation.

Interference fits are a very common shaft-hub connection due to their low manufacturing cost and excellent technical properties. Plastic Conditioning of this machine element is a new and not very well known method. By exploiting residual stresses and the associated increase in the yield point, these components can absorb operating loads such as rotating bending moments, torsion, temperature changes and centrifugal forces purely elastically and avoid plastic deformation during operation. Compared to conventionally joined interference fits, the load bearing capacity in the elastic range can be increased by almost 200% and a specifically defined additional safety against plastic deformation in the elastic-plastic range can be ensured. This paper examines the effects of Reverse Yielding on the technology of Plastic Conditioning of Interference Fits in Power Transmission Engineering. Based on the Shear Stress Hypothesis (SH), the Plane Stress State (PSS) and the ideal plastic behavior of materials, the stress-mechanical relationships are explained, the influencing parameters are examined and conclusions are drawn for the plastic conditioning process. Taking into account the theoretical knowledge according to the state of the art, modified material behavior assumptions (isotropic hardening) and the Von Mises Yield Criterion (VMYC) are also considered. In addition, the method of plastic conditioning of interference fits is introduced and its basic principles are briefly explained. Along with computational suggestions to avoid Reverse Yielding, open issues requiring further research are identified.

Changing the film thickness to manipulate the microstructural properties has been considered as a potential method in practical application. Here, we report that atomic-scale structural properties regulated by film thickness in NiCO2O4(NCO)/CuFe2O4(CFO) bilayer heterostructure prepared on (001)-MgAl2O4 (MAO) substrate by means of aberration-corrected scanning transmission electron microscopy (STEM). The misfit dislocations at NCO/CFO interface and antiphase boundaries (APBs) bound to dislocations within the films both are found in NCO (40 nm)/CFO (40 nm)/MAO heterostructure to contribute to relaxation of mismatch lattice strain. In addition, the non-overlapping a/4[101]-APB is found and the structural transformation of this kind of APB is resolved at atomic scale. In contrast, only the interfacial dislocations form at interface without the formation of APBs within the films in NCO (10 nm)/CFO (40 nm)/MAO heterostructure. Our results provide evidence that formation of microstructural defects can be regulated by changing film thickness to tune magnetic properties of epitaxial bilayer spinel oxide films.

Liposome vesicle is an ideal carrier for carbon nanotube (CNT) to serve as the water channel that allows the fast transport of water molecules, and thus enhancing the membrane permeability. However, low quantity of the inserted CNT in the liposome vesicle is an important factor that limited further improvement of the membrane flux. In present study, positively charged lipids (2,3-dioleoyloxy-propyl)-trimethylammonium-chloride (DOTAP) was introduced to the 1,2-dioleoyl-sn-glycero-3-phosphoethanolamineon (DOPE) liposome vesicles to tailor the vesicle charge, so as to evaluate the effect of positively charged DOTAP on the insertion of CNT into liposomes and separation performance of thin-film nanocomposite (TFN) membranes. The results showed that addition of DOTAP induced more quantity of CNT inserted into the liposome vesicles, since the shrinkage rate (k) and permeability (Pf) of liposome vesicles present obvious increase with increased content of DOTAP in the liposome vesicles. Besides, it contributed to 252.3% higher water flux for TFN membranes containing DOPE/DOTAP2:1-CNT liposomes (the mass ratio between DOPE and DOTAP was 2:1) than TFC membranes. More important, it presented 106.7% higher water flux for TFN membranes containing DOPE/DOTAP4:1-CNT liposomes (the mass ratio between DOPE and DOTAP was 4:1), which was originated from the more water channels that the CNT provided in the liposome vesicles. In all, positively charged DOTAP effectively tailored the vesicle charge, which provided a better carrier for the insertion of more quantity of CNT, and contributed to higher permeability of TFN membranes.

The cornea is an avascular tissue which has attracted much attention by the uniqueness of its anatomical characteristics, it has, in proportion, an enormous size, in relation to the number of vessels, because on average few cells in the organism are away more than 30 microns of a blood vessel. However, the cornea, with a diameter of between 11 and 12 mm, is a unique example. It has been tried to explain the notable absence of blood vessels in the cornea, arguing that corneal tissues are able to take oxygen directly from the air. In this article we are explaining that based on the physicochemical characteristics of molecular oxygen and the cell membrane, cytoplasm, water, and cellular metabolism, it is not possible that epithelial corneal cells directly take oxygen from the air, instead, corneal cells have molecules that can dissociate the water molecules thereby these cells, like any other eukaryotic cells, take the oxygen from the intracell water, like plants.

Perovskite Solar Cell (PSC) is a third-generation photovoltaic device known for its rapid improvement in efficiency levels over the past decade. Moreover, the added benefits of abundant sourcing of raw materials, uncomplicated fabrication process, organic and inorganic device materials, and tuneable bandgaps make this technology a sustainable energy alternative. However, the efficiency values of these devices are subjected to variation depending on factors such as material compatibility, environmental conditions, energy band alignment of device components and stability characteristics to extrinsic and intrinsic factors. One such vital intrinsic factor is film morphology, homogenous and superior film quality formation and pinhole and trap-free films. In this study, we have investigated the formation of perovskite films on a qualitative basis using metal chloride washing of salts such as Erbium, Antimony, Cadmium and Chromium Chloride. The study aims to analyse the difference in film formation with various metal chloride washing and how this could potentially impact or contribute to photovoltaic performance if the devices are fabricated.

Metallic thin-film materials and nanoparticles (mainly Silver (Ag)-based) are recently being used in many nano-technological applications including sensors, reflective heat-mirror coatings, and antibacterial coatings as well. The physical vapor deposition technique attracts significant attention for Ag-based nanocomposites with tailoring the structural and optical properties of metallic thin films thus allowing further improvements and application possibilities in various existing fields namely electronics, catalysis, magnetics, optics in alongside the environment and health and new emergent fields in, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of Silver (Ag)-based nanocomposite thin films prepared by using physical vapor deposition techniques.

In this work, a highly efficient, molybdenum disulfide (MoS2) based near infrared (NIR) heterojunction photodetector is fabricated on a Si substrate using a cost-effective and simple drop casting method. A non-stoichiometric and inhomogeneous MoS2 layer with a S/Mo ratio of 2.02 is detected using energy dispersive X-ray spectroscopy and field emission scanning electron microscope analysis. Raman shifts are noticed at 382.42 cm-1 and 407.97 cm-1, validating MoS2 thin film growth with a direct bandgap of 2.01 eV. The fabricated n-MoS2/p-Si photodetector is illuminated with a 785 nm laser at different intensities, and demonstrate the ability of the photodetector to work in both regions, the forward biased and reverse biased from above 1.5 V and less than -1.0 V. The highest responsivity, R is calculated to be 0.52 A/W while the detectivity D* is 4.08 x 10^10 Jones for an incident light intensity of 9.57 mW/cm2. The minimum rise and fall times are calculated as 1.77 ms and 1.31 ms for an incident laser power of 9.57 mW/cm^2 and 6.99 mW/cm^2 respectively at a direct current bias voltage of 10 V. The demonstrated results are promising for the low-cost fabrication of a thin MoS2 film for photonics and optoelectronic device applications.

Abstract: Molybdenum (Mo) thin films were sputtered from two kinds of Mo targets with different microstructures under the same sputtering process, and the effect of microstructure of Mo target on morphology, deposition rate and resistance of sputtered film were studied and discussed. The results show that morphological differences between Mo thin films sputtered by Mo targets with different microstructures are very small. The more uniform and finer the grain structures of Mo target, the better the uniformity on thickness and resistance of Mo sputtered film. Moreover, during sputtering process, when Mo target’s grain size is finer and the surface area of grain boundary is higher, the thickness reduction of the target is more homogeneous and the sputtering film has faster deposition velocity. The difference in microstructure of the Mo target has not obvious influence on the grain orientation of sputtering film.

tructural and superconducting properties of high quality Niobium nanofilms with different thicknesses are investigated on silicon oxide and sapphire substrates. The role played by the different substrates and the superconducting properties of the Nb films are discussed based on the defectivity of the films and on the presence of an interfacial oxide layer between the Nb film and the substrate. The X-ray absorption spectroscopy is employed to uncover the structure of the interfacial layer. We show that this interfacial layer leads to a strong proximity effect, specially in films deposited on a SiO2 substrate, altering the superconducting properties of the Nb films. Our results establish that the critical temperature is determined by an interplay between quantum-size effects, due to the reduction of the Nb film thicknesses, and proximity effects.

The future power equipment tends to take hydrogen or middle/low heat-value syngas as fuel for low emission. The heat transfer of film cooled turbine blade shall be influenced more by radiation. Its characteristic of conjugate heat transfer is studied experimentally and numerically in the paper by considering radiation heat transfer, multi-composition gas and TBC. The Weighted Sum of Gray Gases spectral model and Discrete Transfer Model are utilized to solve the radiative heat transfer in the multi-composition field, while validated against the experimental data for the studied cases. It is shown that the plate temperature increases significantly when considering the radiation and the temperature gradient of the film cooled plate becomes larger. It is also shown that increasing percentage of steam in gas composition results in increased temperature on the film-cooled plate. The normalized temperature of the film-cooled plate decreases about 0.02, as the total percentage of steam in hot gas increases per 7%. As for the TBC effect, it can smooth out the the temperature distribution and insulate the heat to a greater extent when the radiative heat transfer becomes significant.

Heating films were prepared by using poly(methyl methacrylate) and polybutadiene composites containing graphite. The heating film was prepared by casting the as-made polymer composite on PET film. Copper electrodes were attached to both ends of the as-prepared film, and the heating characteristics of the film was analyzed while applying DC voltage. The electrical conductivity and the heating temperature of the heating films depended on the size, the structure, the content and the dispersion characteristics of the graphite in the composite. The electrical resistance of the heating film was controlled to adjust the heating temperature of the film. The relationship between the physical/chemical structure and the heating characteristics of the composite film was studied by measuring the heating temperature as functions of film thickness and resistance by using an infrared thermal imaging camera. The lower the film resistance, the higher the heating temperature of the film. The surface temperature was uniform throughout the film.

Plastic contamination of small dimensions (

Plastics play a pivotal role in the principles of a circular economy, where their effective recycling post-utilization, leading to economic value generation and minimal environmental harm, is crucial for achieving sustainable management. Extensive research has delved into the incorporation of waste plastics in concrete, showcasing promising outcomes with a myriad of advantages..The escalating volume of plastic waste is becoming a pressing issue, contributing to environmental pollution, particularly in densely populated cities and towns in Nigeria such as Delta, Aba, Port Harcourt, Onitsha, Enugu, Benue, and Ogun. These urban centers experience high consumption of goods packaged or sealed in plastic materials. Tourist destinations are also affected as large quantities of plastic waste are improperly disposed of or incinerated, resulting in environmental contamination and air pollution. Efforts to address this growing concern are crucial to safeguarding the environment and public health in these regions.Therefore, it is imperative to find effective ways to utilize these waste plastics. By cleaning low-density polyethylene bags and combining them with sand at specific proportions, high-strength bricks can be produced. These bricks not only exhibit thermal and sound insulation properties but also help in pollution control and cost reduction in construction projects. This innovative approach not only addresses the issue of accumulating plastic waste, a non-biodegradable pollutant, but also offers a sustainable solution to manage plastic waste while contributing to the construction industry's efficiency and environmental protection., By incorporating waste plastic and nylon into brick production, we not only reduce the amount of sand extracted from our natural resources like rivers and seas but also utilize the surplus plastic waste that is currently discarded. This research focuses on creating eco-friendly bricks by incorporating molten plastic, nylon, and plastic bottles in varying percentages (0 to 15% by weight) along with 5kg of fly ash. The experimental results from this study will shed light on the feasibility and benefits of using these materials in brick manufacturing, highlighting the potential of sustainable construction practices that minimize environmental impact and resource depletion, The experimental process involved utilizing cement and sand to complete the brick composition, with curing conducted underwater for 29 days followed by baking at temperatures between 100°C to 120°C for 2 hours. The resulting eco-friendly bricks exhibited key characteristics such as being lightweight, porous, having low thermal conductivity, and displaying appreciable mechanical strength. Interestingly, the compressive strengths of these bricks, post the addition of waste plastic and nylon, were found to be comparable to that of conventional bricks. Additionally, these eco-friendly bricks showcased reduced water absorption capacity compared to regular bricks, offering a promising alternative for sustainable and efficient construction practices.The eco-friendly bricks made from A, B, C, and D using 0%, 5%, 10%, and 15% plastic/nylon waste showed comprehensive strengths of 19.5 ,19.46, 20.3, and 21.1 respectively, with corresponding water absorption percentages of 0.34, 0.25, 0.22, 0.20, and 0.085. The efflorescence values were lower than those of normal bricks. These bricks are likely to enhance energy efficiency in buildings and provide economic value to manufacturers, thereby promoting a sustainable ecosystem for plastic waste management with the involvement of all stakeholders.

The accumulation of waste plastics has a severe impact on the environment, and therefore, the development of efficient chemical recycling methods has become an extremely important task. In this regard, a new strategy of degradation product-promoted depolymerization process was proposed. Using N,N'-dimethyl-ethylenediamine (DMEDA) as depolymerization reagent, an efficient chemical recycling of poly(bisphenol A carbonate) (BPA-PC) material was achieved under mild conditions. The degradation product 1,3-dimethyl-2-imidazolidinone (DMI) was proven to be the critical factor in facilitating the depolymerization process. This strategy does not require catalysts or auxiliary solvents, which is truly green process. This method improves the recycling efficiency of BPA-PC and promotes the development of plastic reutilization.

This study investigates the spatial and temporal distribution of litter at 7 beach sectors in Cadiz Bay, Southwest Spain. Two ten-day surveys carried out in autumn 2022 and spring 2023 revealed a total of 4,199 and 4,634 items, respectively, with plastic being the predominant material (71.13% in autumn, 88.39% in spring). Litter quantities varied significantly among beaches, La Puntilla showing the highest abundance with 0.48 ± 0.25 items m-1 in autumn and 1.34 ± 0.61 items m-1 in spring. The lowest abundance was recorded at sector 1 of Valdelagrana beach (0.08 ± 0.06 items m-1) during autumn and at El Castillito beach (0.08 ± 0.04 items m-1) during spring. Statistical analyses did not reveal significant differences in litter quantities between autumn and spring, however high significant interaction was shown considering both season and beach lo-cation. Seasonal differences were also observed in litter composition. Litter categories increased from 90 in autumn to 107 in spring. The top 10 litter categories varied between seasons and included cigarette butts, plastic fragments and plastic packaging. Cigarette butts were principally abundant in autumn because re-lated to summer beach users and wet wipes were particularly observed in spring because linked to wastewaters and river discharges especially relevant in winter months. Hydrodynamic and wind conditions were analyzed, revealing complex relationships with litter abundance.

Abandoned, lost, or otherwise discarded fishing gear (ALDFG) is a primary contributor to the entanglement of numerous marine species. Utilizing digital media platforms like Google, Facebook, and Instagram we conducted an assessment of the detrimental effects of ALDFG and plastic litter, on the biodiversity of Italy's marine ecosystem. Our investigation revealed that plastic litter has adverse consequences on various forms of marine life, including reptiles, mammals, birds, fish, crustaceans, and mollusks, along different Italian geographical sub-areas. Several records of interaction between plastic and endangered and vulnerable marine species have been described. Our reports even highlight the impact on marine turtles, mainly on Caretta caretta. This is the first report of entangled with fishing nets in Cetorhinus maximus, Oblada melanura, Serranus scriba, Homarus gammarus, Octopus vulgaris, and Phoenicopterus roseus. Furthermore, we identified that ghost nets have repercussions for endangered and vulnerable marine species. This update sheds light on the ongoing adverse effects of ghost nets on the Italian marine ecosystem, yet it is crucial to acknowledge that the true extent of the problem remains underestimated.

In this study, the autofrettage method, which is used to increase the durability of cylindrical parts, was applied to a barrel made of steel material according to the AISI 4340 standard. Assuming that the barrel works continuously under the pressure of 400 MPa, optimum autofrettage was performed. The stresses occurring on the barrel before and after autofretage were calculated. Additionally, analytical equivalent stress values (Von-Mises) formed on the part's wall were compared with numerical analysis results obtained with a commercial finite element program ANSYS®, and their compatibility was examined. As a result of the calculations and analysis performed, it was observed that autofretage has positive effect on increasing the pressure carrying capacity of the barrel. After autofrettage the cylindrical part, it was determined that the Von-Mises stress values formed in the part wall changed and these stresses took the lowest value at a point (elastic-plastic interface). It has been evaluated that this point gives the optimal autofretage pressure value for a certain operating pressure. After the autofrettage application, it was determined that the Von-Mises Stress value in the barrel wall decreased by 25.27 % and the pressure carrying capacity of the barrel increased without any design or dimensional change. It has been seen that the analytical and numerical analysis results are consistent with each other, and it is expected that this study will guide and contribute to the studies to be conducted on increasing the strength or lightening the weight of the parts.

Ranging from traditional food packaging, clothing, and furniture to the current small and large electronic devices and automobiles, plastics serve to fulfill diverse demands in our daily lives. However, the global plastic waste generation is dramatically escalating, currently standing at approximately 150 million metric tonnes annually. While some of regenerated plastics recycled by mechanical methods can be used as their parent plastics, cost and energy savings are limited by multiple preliminary processes such as plastic sorting, shredding, washing, and drying. Moreover, the continuous mechanical recycling process degrades the physical properties of the materials. In this context, chemical recycling is emerging as a promising alternative method due to its high efficiency, simple preliminary steps, reducing reliance on fossil resources, and conversion of plastic waste into value-added chemicals. This review provides a state-of-the-art overview of contemporary chemical recycling of polymeric materials via i) depolymerization: “polymers to small valuable molecules” and ii) closed-loop cycles: “polymers to monomers, and/or to polymers”, by encompassing both traditional/advanced depolymerization chemistries and the remaining challenges. These recycling approaches are contextualized within the present industrial technologies, key design principles, and specific recycling case studies related to distinct polymeric materials.

The drastically increasing amount of plastic waste is causing an environmental crisis that requires innovative technologies for recycling post-consumer plastics to achieve waste valorization while meeting environmental quality goals. Biocatalytic depolymerization mediated by enzymes has emerged as an efficient and sustainable alternative for plastic treatment and recycling. A variety of plastic- degrading enzymes have been discovered from microbial sources. Meanwhile, protein engineering has been exploited to modify and optimize plastic-degrading enzymes. This review highlights the recent trends and up-to-date advances in mining novel plastic-degrading enzymes through state-of-the-art omics-based techniques and improving the enzyme catalytic efficiency and stability via various protein engineering strategies. Future research prospects and challenges are also discussed

Polyethylene terephthalate (PET) pollution poses significant environmental consequences, and thus new degradation methods must be explored to mitigate this problem. We previously demonstrated that a consortium of three Pseudomonas and two Bacillus species can synergistically degrade PET in culture. The consortium more readily consumes Bis(2-Hydroxyethyl) terephthalate (BHET), a byproduct made in PET depolymerization, compared to PET, and can fully convert BHET into metabolically usable monomers terephthalic acid (TPA) and ethylene glycol (EG). Because of its crystalline structure, the main limitation of the biodegradation of post-consumer PET is the initial transesterification from PET to BHET, depicting the need for the transesterification step in the degradation process. Additionally, there have been numerous studies done on the depolymerization reaction of PET to BHET, yet few have tested the biocompatibility of that product with a bacterial consortium. In this report, a two-step process was implemented for sustainable PET biodegradation, where PET is first depolymerized to form BHET using an Orange Peel Ash (OPA) catalyzed glycolysis reaction, followed by complete degradation of the BHET glycolysis product by the bacterial consortium. Results show that OPA-catalyzed glycolysis reactions can fully depolymerize PET, with an average BHET yield of 92% (w/w) and that the reaction product is biocompatible with the bacterial consortium. After inoculation with the consortium, 19% degradation of the glycolysis product was observed in 2 weeks, for a total degradation percentage of 17% when taking both steps into account. Furthermore, the 10-week total BHET degradation rate was 35%, demonstrating that the glycolysis products are biocompatible with the consortium for longer periods of time, for a total two-step degradation rate of 33% over 10 weeks. While we predict complete degradation is achievable using this method, further experimentation with the consortium can allow for a circular recycling process, where TPA can be recovered from culture media and reused to create new materials.

This study evaluates for the first time the plastic litter occurrence in Posidonia spheroids of four Mediterranean sandy beaches at different anthropogenic impact. A total of 80 spheroids was analyzed and 202 plastic items were found. Spheroids entangled a high number of plastic litter (132 plastic items/kg) with significant differences between beaches. Our results highlight the importance to implement the beach cleaning plan for the removal of all spheroids in order to prevent them from flaking and releasing the marine litter trapped inside them again in the environment. Spheroids should be manually removed in order to protect the banquettes. The removal should be involved all spheroids, independently from their size. This study adds data for the implementation of the monitoring program of marine litter and contributes to the development of specific management measures as well as implement Mediterranean action plans.

Plastic waste management has become a major problem in the present times, and many countries are struggling to deal with it. The situation has become a crisis in developing nations due to a lack of proper waste management, resources, technology, and political will. The extensive usage of foam-based packaging materials such as Styrofoam as a secondary packaging material has led to environmental pollution both in land and water, in developing countries. It is important to address this problem using a sustainable approach such as biomimetic manufacturing. One such solution that is present in developed nations is mycelium-based packaging, wherein the agricultural and industrial-based cellulose waste is converted into a biocomposite with the help of a fungi root network. Such a process has the potential to convert biomass into useful products but also has an indirect effect on pollution reduction by eliminating stubble burning in nations like India. In this review, we examine the details of the manufacturing process, properties, advantages, and limitations of such composite materials. A comparison of the present status of such materials produced in the market by some of the companies across the world is presented. Finally, the challenges involved with such materials and the future directions are discussed.

We currently face several, interlinked environmental crises, including climate change, habitat destruction and biodiversity loss. However, many governments seem unwilling to take strong and immediate action to address these threats, preferring to promote neoliberal approaches to allow consumers and the general public to make environmentally friendly choices. This is despite neoliberal approaches being much less likely to be successful than government leadership, taxation, subsidies, and legislation in addressing environmental issues. In this study, we examine public perception of environmental threats and solutions to these threats, in a survey, mainly completed in the UK. Climate change is seen as the biggest issue, likely due to recent activist campaigns and subsequent media attention on the issue. Neoliberal attitudes, such as green consumer choices to environmental concerns, do still dominate in a series of possible presented solutions, and score more highly than lifestyle changes such as changing diet. However, when questioned specifically about plastic pollution, government intervention to ban all unnecessary plastic scored very strongly, indicating a shift from a consumer driven response. Furthermore, most participants think they are at best only partly ‘doing their bit’ to protect the environment. The results demonstrate that the public are aware that not enough is happening to protect the environment and provide evidence that there is willingness for stronger government intervention to address environmental issues, although there is potential resistance to major lifestyle changes.

A series of Ti₄₀Zr₂₅Cu₉Ni₈Be₁₈)_100-xTM_x (x = 0, 1, 2, 3, 4 at.%, TM = Nb, Y) Bulk amorphous alloys were designed and prepared using the copper mold casting method. The microstructures, glass forming ability and mechanical properties of the alloys were investigated by means of X-ray diffractometry (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), differential scanning colorimetry (DSC), depth-sensitive nanoindentation and uniaxial compressive test. The Bulk amorphous alloys with different ductility were investigated by measuring their plastic deformation energy (PDE) of the first pop-in events during loading. The relationships between the PDE value, shear band formation and ductility in Bulk amorphous alloys have been investigated. The results show that the PDE value decreases by the Nb addition and promotes the generation of multiple shear bands easily, which increase the fracture strength and plasticity significantly. Substituting Nb with Y has exactly the reverse effect. A useful rule for preparing of Bulk amorphous alloys with high plasticity is herein proposed, whereby the chemical composition of the Bulk amorphous alloys can be tailored to possess a lower PDE value.

An influenza A virus (H3N2) with an envelope with the same structure as COVID-19 was used for antiviral testing of material surfaces, in comparison with some results of feline calicivirus. The evaluation method used was the film adhesion method, in which the virus solution is placed on the material and adhered to it using a film. The evaluation method was based on the film adhesion method, in which the virus solution is placed on the material and adhered with a film, and the plaque method, in which the cell virus is allowed to infect the material and form plaques, but the appropriate virus concentration must be adjusted to observe the plaques. When not under that restriction, the plaques are often incomplete; this is observed. For this reason, this study applied an area measurement method that can reflect viral activity even when plaques are not obtained. This study revealed that different types of metallic materials have different antiviral properties. Specifically, the antiviral activity of iron, carbon steel, and nickel was relatively high, while that of stainless steel and titanium was relatively low. The order of antiviral activity was as follows: Fe, SS400, Ni, SUS316L, SUS304, and Ti.

Epitaxial lithium ferrite (LiFe5O8) films with different thicknesses have been successfully fabricated on SrTiO3 (001) substrates by magnetron sputtering deposition technique. The microstructural and magnetic properties are characterized by advanced transmission electron microscope and magnetic measurement device. It was found that the formation of structural defects can be influenced by the thickness of the film. Apart from the misfit dislocations, the orientation domains form in thinner film and twin boundaries appear in thicker film, respectively, contributing to the misfit strain relaxation in the heterosystem. The magnetic measurement shows that the thinner films have enhanced magnetization and a relatively lower coercive field compared with the thicker films containing the antiferromagnetic twin boundaries. Our results provide a way for tuning the microstructure and magnetic properties of lithium ferrite films by changing the film thickness.

Valsartan (Val) is an important antihypertensive medication with side effects such as dizziness and angioedema. These constraints are due to the low oral bioavailability and relatively short half-life. The goal here is to incorporate Val into a mixed micelles system that can enhance transdermal delivery. Thin-film hydration and micro-phase separation were used to produce Val-loaded mixed micelle systems. A variety of factors, including surfactant type and drug-to-surfactant ratio, were optimized to produce micelles with low size and high Val entrapment efficiency (EE). The size, polydispersity index (PDI), zeta-potential, and drug entrapment efficiency of the prepared micelles were all measured. The drug release profiles in vitro were assessed using dialysis bags, and the permeation through abdominal rat skin was assessed using a Franz diffusion cell. All formulations had high EE levels exceeding 90% and low particle charges. The micellar sizes ranged from 107.6 to 191.7nm, with average PDI values of 0.3. The in vitro release demonstrated a uniform slow rate that lasted one week with varying extents. F7 demonstrated a significant (P < 0.01) transdermal efflux of 68.84 ± 3.96 µg/cm2/h through rat skin when compared to the control. As a result, the enhancement factor was 16.57. Val-loaded mixed micelles were successfully prepared using two simple methods with high reproducibility, and extensive transdermal delivery was demonstrated in the absence of any aggressive skin modifying enhancers.

Herein, bamboo-laminated lumber for furniture was coated with waterborne acrylic paint. The effects of different painting techniques and quantities on the drying rate, smoothness, hardness, adhesion and wear resistance of the paint film were investigated. Then, the thermal properties of the paint were analysed using thermogravimetry and differential scanning calorimeter to examine the film-forming mechanism. The results showed that painting technique had no effect on the drying time, flatness, hardness and adhesion of the paint film, but it influenced the wear resistance. Herein, the films’ flatness showed little variation with different painting methods (one-layer primer one-layer topcoat, one-layer primer two-layer topcoat, two-layer primer one-layer topcoat and two-layer primer two-layer topcoat). The drying time for primer surfaces/solids was 8min/8.5 min, while it was 6.5/7 min for topcoats. The paint films exhibited grade B hardness and grade 0 adhesion and the better wear resistance when using one-layer primer one-layer topcoat at 51.24 mg·100 r−1. The amount of paint applied significantly affected the drying time and flatness of the paint film. As the quantity increased, the drying time of the paint’s surfaces and solids also increased, whereas the film’s flatness initially increased before decreasing. The film’s optimal adhesion, hardness and wear resistance values were grade 0, grade B and 51.24 mg·100 r−1, respectively, when 80 g/m2 of paint was applied. Thermal analysis of the primer and topcoat showed that water decomposition occurred at 100℃ and thermal decomposition of organic components occurred at 350℃. The primer and topcoat exhibited the same weight loss, but primer’s thermal loss rate was higher than that of topcoat. Consequently, the topcoat displayed better thermal stability than the primer.

This paper presents the design of a miniaturized polyimide-based antenna for Ultra-Wideband (UWB) communication. Miniaturization is achieved through the utilization of adhesive material with a high dielectric constant (high-Dk). The goal of this work is to investigate the impact of such material on the antenna performance and to optimize its design for UWB operation. The manufacturing of the antenna using the proposed structure was developed and the prototype of antenna for UWB high-band (6 - 9 GHz) is measured and analyzed. By leveraging the high Dk of the adhesive material, the simulation and measurement results showed that the proposed antenna with high Dk adhesive film can achieve the compact dimension with good performance in gain, and time domain characteristics. The results of this study show a potential of exhibiting a reduction in the size of the antenna and will contribute to the advancement of miniaturized UWB antenna technology.

In the present work we have investigated an organic semiconductor based on tris(8-hydroxyquinoline) aluminum (AlQ3) doped with tetracyanoquinodimethane (TCNQ), which can be used as a photoactive layer in organic light-emitting device (OLED). DFT calculations were carried out to optimize the structure of semiconductor species and get related constants in order to compare experimental and theoretical results. The semiconductor AlQ3-TCNQ was structurally characterized and their experimental IR spectrum was compared with that obtained through DFT calculations. Subsequently, AlQ3-TCNQ films with polypyrrole (PPy) matrix were fabricated, they were morphologically and mechanically characterized by Scanning Electron and Atomic Force Microscopy techniques. The maximum stress for the film is 8.66 MPa and the Knoop hardness is 0.0311. The film was analyzed in its optical behavior and the optical properties of hybrid film were found to exhibit two indirect allowed transitions at 2.64 and 3.44 eV. Finally, an OLED type was fabricated that was electrically characterized. Applying a cubic-spline approximation to fit cubic polynomials to the J-V curves, the ohmic to SCLC transition voltage VON and the trap-filled-limit voltage VTFL for the device were obtained. Then, the free carrier density and trap density for the device were approximated to n0=2.4787×10171m3 and Nt=1.7419×10291m3 respectively.