The practical necessity of strengthening of reinforced concrete structure elements requires a choice of a method which would provide cost-effectiveness, simplicity of construction and durability of the chosen solution. One of the ways is strengthening using the material belonging to the group of micro-reinforced concretes called ferrocement. The paper presents the comparative analysis of some of the results of RC beams exposed mainly to flexure, strengthened with ferrocement elements (strips) applied by gluing on the on the tensed side of RC beams. The results are obtained using the experimental, analytical and numerical research on the adequate models. Strengthening of the beams was performed in the form of four types of ferrocement strips (four different strip widths and four different numbers of wire mesh layers). The numerical non-linear analysis using finite elements method (FEM) was employed, with the introduction of the corresponding characteristics of constitutive material obtained by the experiments on the test specimens. The analytical researches were performed using known analytical calculation methods in order to formulate the model for the calculation of the ultimate and serviceability limit states of the strengthened cross-section. The results presented in the paper, through their comparative compatibility, confirmed the applicability of this strengthening method.

New analytical solutions of the heat conduction equation are presented in cylindrical and spherical coordinates. Then these solutions are reproduced with high accuracy by recent explicit and unconditionally stable finite difference methods. After this, real experimental data from the literature regarding a heated cylinder are reproduced by the explicit numerical methods as well as by Finite Element Methods (FEM) ANSYS workbench. Convection and nonlinear radiation are also considered on the boundary of the cylinder, and it is shown that the explicit methods are much more accurate than the commercial software.

Our study essentially concerns the dynamic behavior of an SIRS epidemic model in discrete time. Two equilibrium points are obtained; one is disease-free while the other is endemic. We are interested in the endemic fixed point as well as its asymptotic stability. Depending on the parameters which are estimated using the data from US Department of health and SIRS modelling with optimization, two Flip and Transcritical bifurcations appear. We illustrate their diagrams, as well as their bifurcation curves using the method of Carcasses \cite{carcasses1993determination,carcasses1995singularities} for the Flip bifurcation and by an implicit function deduced from such an equation for the Transcritical bifurcation. We use the scanning of the parametric plane to have a global view of the behavior of the model and to highlight the zones of stability of the existing singularities. A superposition of the bifurcation curves with the parametric plane can show the overlap of the curves with the boundaries of the stability domains, which confirms the smooth running of the simulation and its correspondence with the theory, we finish this article with constrained optimal control applied to infection rate and recruitment rate for an SIRS discrete epidemic model. Pontryagin's maximum principle is used to determine these optimal controls. Finally using COVID-19 data in the USA, we obtain results that demonstrate the effectiveness of the proposed control strategy to mitigate the spread of the pandemic.

Groundwater models serve as support tools to among others: assess water resources, evaluate management strategies, design remediation systems and optimize monitoring networks. Thus, the assimilation of information from observations into models is crucial to improve forecasts and reduce uncertainty of their results. As more information is collected routinely due to the use of automatic sensors, data loggers and real time transmission systems; groundwater modelers are becoming increasingly aware of the importance of using sophisticated tools to perform model calibration in combination with sensitivity and uncertainty analysis. Despite their usefulness, available approaches to perform this kind of analyses still present some challenges such as non-unique solution for the parameter estimation problem, high computational burden and a need of a deep understanding of the theoretical basis for the correct interpretation and use of their results, in particular the ones related to uncertainty analysis. We present a brief derivation of the main equations that serve as basis for this kind of analysis. We demonstrate how to use them to estimate parameters, assess the sensitivity and quantify the uncertainty of the model results using an example inspired by a real world setting. We analyze some of the main pitfalls that can occur when performing such kind of analyses and comment on practical approaches to overcome them. We also demonstrate that including groundwater flow estimations, although helpful in constraining the solution of the inverse problem as shown previously, may be difficult to apply in practice and, in some cases, may not provide enough information to significantly constrain the set of potential solutions.

Currently, the use of numerical models for reproducing the landscape evolution of a river basin is part of the day-by-day research activities of fluvial engineers and geomorphologists. However, despite landscape modelling is based on a rather long tradition, and scientists and practitioners are trying to schematize the processes involved in the evolution of a landscape since decades, there is still the need for improving both the knowledge of the physical mechanisms and their numerical coding. The present review focuses on the first aspect, discussing the main components of a landscape evolution model and their more common schematizations, presenting possible open questions to be addressed towards an improvement of the reliability of such kind of models in describing the fluvial geomorphology.

Subsurface temperature is the key parameter in geothermal exploration. An accurate estimation of the reservoir temperature is of high importance and usually done either by interpolation of borehole temperature measurement data or numerical modeling. However, temperature measurements at depths which are of interest for deep geothermal applications (usually deeper than 2 km) are generally sparse. A pure interpolation of such sparse data always involves large uncertainties and usually neglects knowledge of the 3D reservoir geometry or the rock and reservoir properties governing the heat transport. Classical numerical modeling approaches at regional scale usually only include conductive heat transport and do not reflect thermal anomalies along faults created by convective transport. These thermal anomalies however are usually the target of geothermal exploitation. Kriging with trend does allow including secondary data to improve the interpolation of the primary one. Using this approach temperature measurements of depths larger than 1,000 m of the federal state of Hessen/Germany have been interpolated in 3D. A 3D numerical conductive temperature model was used as secondary information. This way the interpolation result reflects thermal anomalies detected by direct temperature measurements as well as the geological structure. This results in a considerable quality increase of the subsurface temperature estimation.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

The Gleeble-1500D thermal simulation test machine was used to conduct the isothermal compression test on 21-4N at the strain rate ( ) of 0.01-10s-1, the deformation temperature (T) of 1273-1453K and the maximum deformation is 0.916. The data of the stress-strain ( - )were obtained. Based on the - data, the Johnson-Cook (J-C), modified J-C, Arrhenius and Back-Propagation Artificial Neural Network (BP-ANN) models were established. The accuracy of four models were verified, analyzed and compared. The results show that J-C model has a higher accuracy only under reference deformation conditions. When the deformation condition changes greatly, the accuracy of J-C model is significantly reduced. The coupling effect of T and of modified J-C model is considered, and the prediction accuracy is greatly improved The Arrhenius model introduces Zener-Hollomon (Z) to represent the coupling effect of T and , it has a fairly high prediction accuracy. And it can predict flow stress ( ) accurately at different conditions. The accuracy of BP-ANN model is the highest, but its learning rate is low, the learning and memory are unstable. It has no memory for the weights and thresholds of the completed training. So, there are certain limitations of it in use. Finally, a FEM of the isothermal compression experiment for four models were established, and the distribution of the equivalent stress field, equivalent strain field and temperature field with the deformation degree of 60% were obtained.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

Rigid-hulled inflatable boats are extremely practical and popular nowadays. They offer a effective conciliation among usability and costs. Their stable and seaworthy behaviour is guaranteed by performing hydroplaning hulls coupled with unsinkable inflated tubes. At the same time, their design is often based on tradition and preconceptions. Rarely, the design assumptions are validated by the reality or, even, by deeper investigations. In this article, both numerical methods and experimental mechanics techniques are proposed as an essential way for supporting the designers in their decisive tasks. Three different situations are detailed where a numerical or an experimental approach shows its benefit inside the engineering design process: firstly permitting to investigate the behaviour of materials driving the fiberglass selection; then measuring the levels of stress and strain in the hull during sailing; finally, using all available information as a base for developing numerical models of the hull slamming in waves. Even if the discussion is focused on a rigid inflatable boat, large part of its considerations is relevant beyond this special case.

This article develops duality principles and numerical results for a large class of non-convex variational models. The main results are based on fundamental tools of convex analysis, duality theory and calculus of variations. More specifically the approach is established for a class of non-convex functionals similar as those found in some models in phase transition. Finally, in the last section we present a concerning numerical example and the respective software.

The main objective of this study is to find out the influence of cooperation and intra-specific competition in escaping predation through refuge of the prey population and the effect of the two intra-specific interactions on the dynamics of prey-predator systems. For this purposes, two mathematical models with Holling type-II functional response function have been proposed and analyzed. The first model includes cooperation among prey populations whereas the second one incorporates intra-specific competition. Existence conditions and stability of different equilibrium points of both models have been carried out for the qualitative behaviour of the systems. Refuge through intra-specific competition has a stabilizing role, whereas cooperation has a destabilizing role on the system dynamics. Periodic oscillations are observed in both the systems through Hopf bifurcation. From the analytical and numerical findings, we conclude that intra-specific competition affects the prey population and continuously checks the refuge class under a critical value, and thus it never becomes too large to cause predator extinction due to food scarcity. Conversely, cooperation leads maximum individuals to escape predation through the refuge so that predators will suffer from low predation success.

The research on the excavation mechanical properties of underpass tunnels has already had certain results, but fewer of them consider the effects of dynamic and static loads on the excavation mechanical properties of underground tunnels at the same time, especially the lack of research cases of double-line highway tunnels with angled underpasses of existing railway tunnels. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel passing under the Hurong Railway at an oblique angle, the mechanical parameters of the rock body in the cross-tunneling area under the influence of static and dynamic load coupling are obtained by using the disturbance quantification coefficients and the Hoek-Brown criterion based on the method of over-advanced geological prediction and the investigation of the surrounding rock on the palisade face, and the engineering-scale finite element model is constructed and the mechanical characteristics of the excavation in the tunnel of the double-lane highway tunnel passing under the existing railroad under the influence of the static and dynamic loads are analyzed. The results show that: the new tunnel rock movement law for the top of the arch sinking, bottom plate bulging, side wall to move outward, the height and width of the arch and bottom plate arch with the tunnel excavation and increase, the side wall rock displacement effect is smaller; left and right lines of the tunnel disturbed area of the rule of change is similar; the existing tunnel bottom plate displacement is more than the top plate and the left and right side walls by the excavation of the time step influence is larger. Typical profile displacement is mainly determined by the distance from the excavation surface; the new tunnel in the four types of calculation conditions of the rock disturbance angle is the same; the existing tunnel roof and side wall Von Mises stress extreme occurs in the tunnel structure, the bottom plate there are pressure relief and pressure-bearing areas; based on the displacement control criteria, the recommended upper and lower step blasting method.

Predictive numerical models in the study of ground-borne vibrations generated by railway sys-tems have traditionally relied on the segmented approach of subsystems. In this approach, loads are individually applied, and the cumulative effect of rolling stock is obtained through superposi-tion. While this method serves to mitigate computational costs, it may not fully capture the com-plex interactions involved in ground-borne vibrations. Recent advancements in computational and software tools have enabled the development of more sophisticated vibrational pollution models. These advanced models encompass the entire dynamic system, from the rolling stock to the terrain, allowing for continuous simulations with a defined time step. Furthermore, the incorporation of computational contact tools between various ele-ments not only ensures temporal accuracy but also extends the analysis to the frequency domain. This paper explores the evolution of predictive numerical models in the context of ground-borne vibrations generated by trains on ballasted tracks. It highlights the shift from segmented models to continuous simulations, demonstrating the progressive advancement towards more comprehen-sive and accurate representations of railway-induced and generated vibrations in the track sur-roundings as an additional way of evaluate sustainability of infrastructures. In particular, this development of a numerical model from its inception aimed to expand upon ex-isting emission - prediction models by enriching the data with frequency-domain information. This approach has been driven by the aspiration to bridge the gap between numerical predictions and measured signals, striving for a higher level of accuracy in our obtained results. This model can predict the impact of a high-speed rail (HSR) vehicle passing on its own track. It possesses sufficient information in both the time and frequency domains to precisely characterize vibrations. This initiative marks a pivotal advancement, enabling us to more effectively capture the intricacies of ground-borne vibrations and their impact on the surrounding environment due to a deeper comprehension of the occurrences in the frequency domain, there's a heightened ca-pability to accurately characterize vibrations.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.

A problem of efficacy of crystal growth methods for crystallization from solution or melt has been investigated. Axial vibrational control (AVC) technique was considered as a perspective method to manage both heat-mass transfer and chemical component composition of the melts in the case of crystallization of complex chemical compounds. Numerical modeling and the search for generalized dependencies made it possible to predict the AVC parameters that provide optimal heat and mass transfer modes for creating flat liquid-solid interfaces, as well as the component composition of dissociated melts of various chemical compounds – Ge, NaNO3, CdTe.

Due to the continued deepening of today’s mining projects, there is a need to develop new or improved rockbolts that are strong and yielding and have high energy absorption when exposed to dynamic loading. Impact tests can provide useful information about the dynamic response of rockbolts but most laboratory tests involve high costs in preparation and result validation. Numerical modeling is an alternative that, in addition to complementing laboratory results, can be used to represent the process of deformation and energy absorption of support elements. In this paper the implementation and results obtained from a finite difference (FDM) numerical model are presented. The model functions as a simulation tool to illuminate all the elements that conform the large-scale (1:1) impact test and their behavior and influence on the dynamic response of a threadbar bolt (22 mm nominal diameter). The model was calibrated using published results and based on these results as well as parametric analysis, the response of each component (steel tube, grout, and bolt) could be identified and its behavior in terms of absorbed energy and displacement could be observed. Results show the model can provide important preliminary information to make design decisions about support elements design.

The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

Local polynomial smoother (LPS) is a weighted local least-squares nonparametric method. It provides a local Taylor series fit of the data at any location and can be directly used in a differential equation to provide a numerical scheme. In this article, we introduce this new nonparametric idea based on local polynomial smoother, for acquiring the numerical solution of the Bagley-Torvik fractional-order differential equations. Furthermore, this paper will present a numerical comparison with some methods, such as legendre operational matrix and pseudo-spectral method. The efficiency and accuracy of the LPS method are demonstrated by two numerical examples.

Human number understanding is thought to rely on the analogue number system (ANS), working according to Weber’s law. We propose an alternative account, suggesting that symbolic mathematical knowledge is based on a discrete semantic system (DSS), a representation that stores values in a semantic network, similar to the mental lexicon or to a conceptual network. Here, focusing on the phenomena of numerical distance and size effects in comparison tasks, first we discuss how a DSS model could explain these numerical effects. Second, we demonstrate that DSS model can give quantitatively as appropriate a description of the effects as the ANS model. Finally, we show that symbolic numerical size effect is mainly influenced by the frequency of the symbols, and not by the ratios of their values. This last result suggests that numerical distance and size effects cannot be caused by the ANS, while the DSS model might be the alternative approach that can explain the frequency-based size effect.

Climate warming is expected to have pronounced effects on Arctic and Subarctic ecosystems, especially regions underlain by discontinuous and relatively warm permafrost. The main goal of this research is to evaluate the vulnerability and dynamics of permafrost under climate warming across the various ecotypes in respect of ecosystem stability, socioeconomic impact, and for better understanding possible future environmental changes. We suggested the new version of the spatially distributed permafrost dynamics model (GIPL2-MPI), which is developed in the Geophysical Institute, University of Alaska Fairbanks. This model is based on the ecosystem approach to simulate the permafrost dynamics, which we are discussing in this paper. We combined ground-based observations and numerical freeze/thaw modeling using climate-ecosystem-permafrost interactions to understand the physical processes and mechanisms controlling permafrost physical state. We predict the changes in permafrost conditions using output from two GCMs (NCAR-CCSM4 and GFDL-CM3) and Five-Model Average Ensemble for the RCP-4.5 and RCP-8.5 scaled down to 1 by 1 km spatial resolution (https://uaf-snap.org/) across entire Alaska. Our result shows that by the end of the current century widespread near-surface permafrost degradation could begin everywhere in Alaska southward of the Brooks Range as well as across some spots at the North Slope Alaska.

Modular steel buildings (MSBs) interlocking inter-module connections (IMCs) have piqued researchers’ interest. However, the existing literature has not yet studied the optimisation of its plate thicknesses. This paper, therefore, focuses on optimising interlocking (IMCs) plate thickness in (MSBs), leveraging previous experimental and numerical simulation methodologies. Various numerical models for four MSBs interlocking (IMCs) with plate thicknesses (4 mm, 6 mm, 10 mm, and 12 mm) were developed under compression loading conditions. The study’s novelty lay in its comprehensive parametric analysis, which evaluated the slip phenomenon in (MSBs) connections and introduced a slip prediction model validated against empirical data. Further innovative machine learning approach was utilised to predict slip values based on applied force through a random forest regression model trained using the 'Treebagger' function. Sensitivity analysis and comparisons with alternative methods were utilised to underscore the reliability and applicability of the findings. The results showed that 11.03 mm was the optimal plate thickness for interlocking (IMCs) in modular steel buildings, with up to 8.08% reduced material costs. Increasing plate thickness boosts its deformation resistance by up to 50.75%. ‘TreeBagger’ random forest for anomaly detection and machine learning improves slip prediction up to 7% at higher force levels.

The study examines the behavior of the Mechanically Stabilized Earth (MSE) wall using available reinforcement materials in Danang, Vietnam. The MSE was reinforced by the self-fabricated galvanized steel grids using CB300V steel with 3 cm ribs. The backfill soil is a sandy clay soil from the local area with a low cohesion. A full-scale model with full instrumentation was installed to investigate the distribution of tensile forces along the reinforcement layers. The highest load that caused the wall to collapse due to internal instability (reinforcement rupture) was 302 kN/m2, which is 15 times the design load of 20 kN/m2. The failure surface within the reinforced soil had a parabolic sliding shape which is similar to the theoretical studies. At the failure load level, the maximum lateral displacement at the top of the wall facing was small (3.9 mm) which is significantly lower than the allowable displacements for the retaining wall. Furthermore, a numerical model using FLAC software was applied to simulate the performance of the MSE wall. The modeling results are in good agreement with the physical model. Thus, the self-fabricated galvanized steel grids could be confidentially used in combination with the local backfill soil for the MSE walls.

This study concerns the transport and retention of polydisperse micron-sized (16 ± 6 µm) of microplastics (MPls) in porous media under varying flow rate conditions. Sorption kinetics were modeled using first-order reversible and irreversible kinetic sorption models, with sensitivity analyses providing insights into each sorption parameter's effect. Both numerical modeling and experimental measurements were employed to assess sand filter retention rates. The impact of flow rate on sorption reveals variations in distribution coefficient (Kd), mass transfer coefficient (β), and irreversible sorption rate (K1). Lower flow rates are correlated with higher Kd and β values, indicating an increase in sorption and diminished mass transfer rates. The findings revealed that an increase in Kd resulted in a more gradual sorption process with a decrease in peak concentration, whereas changes in β influenced the rate of sorption and peak concentration to a lesser extent compared to Kd. Lower K1 values are associated with higher peak concentrations and decreased retention efficiency. Retention rates were evaluated by a numerical model and found as 28 ± 1% at a flow rate of 31 ml min⁻¹ and 17 ± 1% at 65 ml min⁻¹. The introduction of MPls into soil environments has been noted to modify transport dynamics into soil. As a result, these alterations effects hydrological characteristics of soil, thereby impacting quality of groundwater and agricultural output. The mean absolute error (MAE) of 6% between modeled and observed retention rates suggests minor discrepancies. This study highlights the importance of examining retention efficiency and the accuracy of numerical models in porous media during MPl transport.

In this paper major machine learning (ML) tools and the most important applications developed elsewhere for numerical weather and climate modeling systems (NWCMS) are reviewed. NWCMSs are briefly introduced. The most important papers published in this field in recent years are reviewed. The advantages and limitations of the ML approach in applications to NWCMS are briefly discussed. Currently, this field is experiencing explosive growth. Several important papers are published every week. Thus, this paper should be considered a simple introduction to the problem.

Hemodynamic relevance of differently located stenoses of the internal jugular veins remains undetermined. It particularly concerns nozzle-like strictures in the upper parts of these veins and stenotic jugular valves located at the end of this vein. This study was aimed at understanding flow disturbances caused by such stenoses. Computational fluid dynamics software, Flowsquare+, was used. We constructed 3-dimensional models of venous outflow, comprising two alternative routes: tube representing the internal jugular vein and irregular network representing the vertebral veins. At the beginning of the tube representing the internal jugular vein, differently-shaped and sized short strictures, representing nozzle-like strictures were built in. At the end of this tube, differently-shaped membranes, representing the jugular valve, were built in. With the use of computational fluid dynamics modeling, we studied how these two obstacles influenced the outflow. We found that the most relevant outflow disturbances were evoked by nozzle-like strictures in the upper part of the internal jugular vein that were either small, long or asymmetrically positioned. Very tight stenotic valves and septum-like malformed valve were equally hemodynamically relevant. These findings suggest that both upper and lower strictures of the internal jugular vein can be of clinical significance.

Tsunami modeling and simulation has changed in the past few years more than it had in decades, especially so with respect to coastal inundation. Among other things, this change is supported by the approaching era of exa-scale computing, whether via GPU or more likely forms of hybrid computing whose presence is growing across the geosciences. For reasons identified across this review, exa-scale computing efforts will impact the on-shore, highly turbulent r\'egime to higher degree than the 2D shallow water equations used to model tsunami propagation in the open ocean. This short review describes the different approaches to tsunami modeling from generation to impact and underlines the limits of each model based on the flow r\'egime. Moreover, from the perspective of a future comprehensive multi-scale modeling infrastructure to simulate a full tsunami, we underline the current challenges associated with this approach and review the few efforts that are currently underway to achieve this goal. A table of existing tsunami software packages is provided along with an open Github repository to allow developers and model users to update the table with additional models as they are published and help with model discoverability.

This paper presents the results of laboratory tests of CFRP (carbon fibre-reinforced polymer) laminates, which allowed the development of numerical material models. The obtained data were used in a further stage to perform numerical simulations of four variants of medical tabletops differing, among other features, in the shape of the cross-section. Maximum deflections and effort in the composite material were analyzed. The final step was to perform a laboratory test for one of the tabletop versions, the results of which confirmed the correctness of the numerical calculations. This work is aimed at both researchers and designers involved in the practical application of fibre-reinforced polymer matrix composites.

The present study aims to develop an efficient numerical method for computing the diffraction and radiation of water waves with horizontal long cylindrical structures, such as floating breakwaters. A higher-order scheme is used to discretize geometry of the structure as well as the relevant physical quantities. As the kernel of this method, Wehausen’s free-surface Green function is calculated by a newly-developed Gauss-Kronrod adaptive quadrature algorithm after elimination of its Cauchy-type singularities. To improve computational efficiency, a Chebyshev approximation approach is applied to a fast calculation of the Green function that needs evaluation thousands of times. In addition, OpenMP parallel technique is used to the formation of influence coefficient matrix, which significantly reduces CPU time. Finally, computations are performed on wave exciting forces and hydrodynamic coefficients for the long cylindrical structures, either floating or submerged. Comparison with other numerical and analytical methods demonstrates good performance of the present method.

The fractional derivatives are a generalization the derivatives of integer order and find applications in studying memory processes in various scientific fields. Numerical methods are used to solve and analyze fractional models of real world problems. In this paper, we consider an approximation of the Caputo fractional derivative and its asymptotic formula, whose generating function is the polylogarithmic function. In the paper, we prove the convergence of the approximation and derive an estimate for the error and order. We consider an application of the approximation for the construction of finite difference schemes for numerical solution of the two-term ordinary fractional differential equation and the time-fractional Black-Scholes equation for option pricing. The properties of the approximation are used to prove the convergence of the methods used for numerical solution of the fractional differential equations. The theoretical results for the error and order of the methods are illustrated by the results of numerical experiments.

Alzheimer's disease (AD) is the first cause of dementia worldwide and represents a public health challenge. Current diagnostic methods still rely on extended interviews and paper tests. We aim to create a novel, quick cognitive-screening tool on a numerical tablet. This program, built and edited with Unity®, runs on Android® for the Samsung Galaxy Tab S7 FE®. Composed of seven tasks inspired by the Mini-Mental Status Examination and the Montréal Cognitive Assessment, it browses several cognitive functions. The architectural design of this tablet application is distinguished by its multifaceted capabilities, encompassing not only seamless offline functionality but also a mechanism to ensure the singularity of data amalgamated from diverse sites. Additionally, a paramount emphasis is placed on safeguarding the confidentiality of patient information in the healthcare domain. Furthermore, the application empowers individual site managers by allowing them to access and peruse specific datasets, thereby enhancing their operational efficacy and decision-making processes. We performed a usability assessment among 24 healthy patients with a final F-SUS score of "excellent". Participants perceived the tool as simple to use and achieved the test in a mean time of 142 seconds, confirming that a short assessment on a numerical tablet is possible.

A case of low level windshear at Beijing Daxing International Airport is studied in the present pa-per. It is related to the synoptic scale/mesoscale changes of the airflow pattern over northern China. The shear was captured well by the Doppler LIDAR at the airport and timely alerts had been issued. This study considers the technical feasibility of forecasting the shear feature using a high resolution numerical weather prediction model with a lead time of several hours. It turns out that the shear feature could be forecast well, and is generally consistent with the actual observations. However, there are still discrepancies between reality and the simulation, such as the strength of the shear and persistency of the feature. More cases of windshear at Daxing airport would be studied in the fu-ture in order to understand the nature of windshear over there.

We investigated preschool-aged children’s understanding of early fractional tasks and how that performance correlates with fine motor skills and use of gestures while counting. Participants were 33 preschoolers aged 4 to 5 in two Southeastern public elementary schools. Children were tested individually in an interview-like setting. Mathematics tasks were presented in a paper and pencil format and the Grooved Pegboard test assessed fine motor skills. Finally, utilization of gestures was evaluated by taking a behavioral rating of the child’s hand morphology, accuracy of gestures, and synchrony of gestures and spoken word while performing a counting task. Results indicate performance on fractional reasoning tasks significantly predicts both fine motor ability and accuracy of gestures.

The conventional explanation of delayed-choice experiments seems to violate our causal intuition. This apparent violation is caused by a misinterpretation of the conventional formulation of quantum mechanics. I reanalyze these experiments using advanced and time-symmetric formulations of quantum mechanics. All three formulations give the same experimental predictions, but the advanced and time-symmetric formulations violate our causal intuition that effects only happen after causes. I explore reasons why our causal intuition may be wrong at the quantum level. I also suggest how conventional causation might be recovered in the classical limit, and speculate on cosmological boundary conditions.

A multiscale modeling concept for numerical simulation of multiphysics turbulent flow utilizing map-based advection is described. The approach is outlined with emphasis on its theoretical foundations and physical interpretations in order to establish the context for subsequent presentation of the associated numerical algorithms and the results of validation studies. The model formulation is a synthesis of existing methods, modified and extended in order to obtain a qualitatively new capability. The salient feature of the approach is that time advancement of the flow is fully resolved both spatially and temporally, albeit with modeled advancement processes restricted to one spatial dimension. This one-dimensional advancement is the basis of a bottom-up modeling approach in which three-dimensional space is discretized into under-resolved mesh cells, each of which contains an instantiation of the modeled one-dimensional advancement. Filtering is done only to provide inputs to a pressure correction that enforces continuity and to obtain mesh-scale-filtered outputs if desired. The one-dimensional advancement, the pressure correction, and coupling of one-dimensional instantiations using a Lagrangian implementation of mesh-resolved volume fluxes is sufficient to advance the three-dimensional flow without time advancing coarse-grained equations, a feature that motivates the designation of the approach as autonomous microscale evolution (AME). In this sense, the one-dimensional treatment is not a closure because there are no unclosed terms to evaluate. However, the approach is additionally suitable for use as a subgrid-scale closure of existing large-eddy-simulation methods. The potential capabilities and limitations of both of these implementations of the approach are assessed conceptually and with reference to demonstrated capabilities of related methods.

This paper presents a hydrodynamic numerical model for a pitching wave energy converter (WEC). The model uses potential wave theory and is based on Cummins' equation, with nonlinear hydrostatic restoring stiffness and excitation forces based on instantaneous body position and water surface elevation. The numerical model can include non-linear forces, like quadratic drag, power-take-off and other forces that may account for unknown viscous effects observed in experiments. The paper discusses the applicability and limitations of the code and presents the cases where assumptions and simplifications can be made. The goal is to conclude on the simplest, yet accurate, version of the model by evaluating its accuracy using experimental data. The case study for validation is Floating Power Plant's (FPP's) WEC [1]. In the full-scale commercial project, FPP's device consists of a semisubmersible platform hosting a wind turbine (5-8MW) and 4 WECs, each one connected to the platform by a rotation shaft. Due to the configuration of the platform, strong interactions occur between the WECs and the structure, as they are very closely spaced. In order to validate a numerical model able to simulate these hydrodynamic interactions, wave basin experiments with a similar but simplified setup were performed.

Transition between free-surface and pressurized flows is an crucial phenomenon in many hydraulic systems, including water distribution systems, urban drainage systems, etc. During the transition, the force exerted on the structures changes drastically, thus it is meaningful to simulate this process. However, severe numerical oscillations are widely observed behind filling-bores, causing unphysical pressure variations and even computation failure. In this paper, some oscillation-suppressing approaches are reviewed and evaluated on a benchmark model. Then a new oscillation-suppressing approach is proposed to admit numerical viscosity when the water surface is at proximity of conduct roof which has first order accuracy. This approach adds numerical viscosity when water surface is at the proximity of conduct roof. It can sufficiently suppress numerical oscillations under an acoustic wave speed of 1000m/s and is simple to apply. In comparison with two experiments, the simulation results of this method show good agreement and little numerical oscillations. The results in this paper can help readers to choose an appropriate oscillation-suppressing method to improve the robustness and accuracy of flow regime transition simulations.

Understanding the infiltration and solidification processes of liquid 5083Al alloy into Al2O3 three-dimensional reticulated porous ceramic (Al2O3(3D) RPC) is essential for optimizing the microstructure and properties of Al2O3(3D)/5083Al interpenetrating phase composites (IPCs) prepared by low-pressure infiltration process (LPIP). This study employs ProCAST software to simulate the infiltration and solidification processes of liquid 5083Al with pouring velocities (PV) of 0.4 m/s infiltrating into Al2O3(3D) RPC preforms with varying porosities at different pouring temperatures (PT) to prepare Al2O3(3D)/5083Al IPCs using LPIP. The results demonstrate that pore diameter of Al2O3(3D) RPC preforms and PT of liquid 5083Al significantly influence the of the infiltration. Solidification process analysis reveals that the Al2O3(3D) RPC preform with smaller pore diameters allows the lower pouring velocity of 5083Al to solidify faster compared to the preform with larger pore diameters. Al2O3(3D)/5083Al IPCs were prepared successfully from Al2O3(3D) RPC porosity of 15 PPI with liquid 5083Al at PV 0.4 m/s and PT 800 °C using LPIP, resulting in nearly fully dense composites, where both Al2O3(3D) RPCs and 5083Al interpenetrate throughout the microstructure. The infiltration and solidification defects were reduced under air pressure of 0.3 MPa (corresponding to PV of 0.4 m/s) during LPIP. Finite volume method simulations are in good agreement with experimental data, validating the suitability of the simplified model for Al2O3(3D) RPCs in the infiltration simulation.

The study of the influence of the nanoparticle volume fraction and aspect ratio of microchannels on the fluid flow and heat transfer characteristics of nanofluids in microchannels is important in the optimal design of heat dissipation systems with high heat flux. In this work, the computational fluid dynamics method was adopted to simulate the flow and heat transfer characteristics of two types of water–Al2O3 nanofluids with two different volume fractions and five types of microchannel heat sinks with different aspect ratios. Results showed that increasing the nanoparticle volume fraction reduced the average temperature of the liquid–solid heat transfer surface and thereby improved the heat transfer capacity of the nanofluids. Meanwhile, the increase of the nanoparticle volume fraction led to a considerable increase in the pumping power of the system. Changing the aspect ratio of the microchannel effectively improved the heat transfer capacity of the heat sink. Moreover, increasing the aspect ratio effectively reduced the average temperature of the heating surface of the heat sink without significantly increasing the flow resistance loss. When the aspect ratio exceeded 30, the heat transfer coefficient did not increase with the increase of the aspect ratio. The results of this work may offer guiding significance for the optimal design of high heat flux microchannel heat sinks.

The structure of turbulent flow over non-flat surfaces is a topic of major interest in practical applications in both engineering and geophysical settings. A lot of work has been done in the fully rough regime at high Reynolds numbers where the effect on the outer layer turbulence structure and the resulting friction drag is well documented. It turns out that surface topology plays a significant role on the flow drag especially in the transitional roughness regime and therefore, hard to characterize. Survey of literature shows that roughness function depends on the interaction of roughness height, flow Reynolds number and topology shape. In addition, if the surface topology contains large enough scales then it can impact the outer layer dynamics and in turn modulate the total frictional force. Therefore, it is important to understand the mechanisms underlying drag increase from systematically varied surface undulations in order to better interpret quantifications based on mean statistics such as roughness function. In this study, we explore the mechanisms that modulate the turbulence structure over a two-dimensional (2D) sinusoidal wavy surface with a fixed amplitude, but varying slope. To accomplish this, we model the turbulent flow between two infinitely wide 2D wavy plates at a friction Reynolds number, $Re_{\tau}=180$. We pursue two different but related flavors of analysis. The first one adopts a roughness characterization flavor of such wavy surfaces. The second one focuses on understanding the non-equilibrium near surface turbulence structure and their impact on roughness characterization. Analysis of the different statistical quantifications show strong dependence on wave slope for the roughness function indicating drag increase due to enhanced turbulent stresses resulting from increased production of vertical velocity variance from the surface undulations.

In the present paper four passive micromixers designs (G1, G2, G3 and G4) inspired on distillation columns trays were proposed. The devices performance was assessed by numerical simulations. The mixing performance was investigated for a Reynolds number range from 0.01 to 100 and channel height of 200 µm, 500 µm and 1000 µm for oil/ethanol flow. G1 and G4 designs provided high mixing index (> 0.975). The G1 device achieved superior mixing performance with a moderate pressure drop (about 0.5 MPa) due to the induced flow recirculation pattern for a relative high flow rate of 0.21 L/min, highlighting the potential use of such microdevice for scale-up and numbering-up of microdevices in modular chemical plant processing.

In this work, some numerical radius inequalities based on the recent Dragomir extension of Furuta's inequality are obtained. Some particular cases are also provided.

We provide a very general review of the resonant transmission line method for optical fiber problems. The method has been found to work seamlessly for a variety of difficult problems including elliptical and eccentric core fibers as well as “holey”, photonic crystal fibers. A latest version has been shown to offer great versatility with respect to cases of unconventional, inhomogeneous index profiles.

In the context of post-harvest pest management in agricultural products, the adoption of modified atmospheres presents an eco-friendly alternative to conventional pesticides. This study focuses on nitrogen gas as a potential agent for insect control in stored commodities, utilizing computational simulations to investigate its penetration and distribution within two common storage configurations: chamber-contained pallets and silos. By employing the convection-diffusion equation, the simulations reveal insights into nitrogen distribution dynamics and duration required for oxygen reduction. The results highlight the influence of boundary conditions, commodity porosity, and convection effects on nitrogen dispersion. In chamber scenarios, boundary condition type significantly affects oxygen reduction time, while in silos, convection and diffusion interact to establish a consistent diffusion layer thickness. This research enhances the understanding of modified atmosphere techniques and their potential for sustainable pest management. It provides practitioners with valuable quantitative insights, paving the way for optimized modified atmosphere strategies in real-world agricultural contexts.

High density of buildings and the large traffic volume of cities give rise to narrow spaces and high passenger flows in most subway stations. When evacuation is required during an emergency, these problems may trigger issues in operational safety. Therefore, it is imperative to comprehensively assess subway station emergency evacuation times and capacities during the operating process to ensure the design is safe, science-based, and rational. To further enhance safe evacuation capacity, this paper proposes an overall evacuation time model that considers the multielement charac-teristics of subway stations in multiple segments. The evacuation route is decomposed into five stages according to the critical nodes in the evacuation process. An overall emergency evacuation time model is established based on the diversity of bottlenecks in the five stages, integrating elements such as the horizontal movement velocity of passengers, subway equipment parameters, and human density. Taking Xi’an Wulukou Subway Station as an example, this paper verifies the outcomes of the theoretical model against the Pathfinder software and conducts additional anal-yses of the evacuation conditions of stairs and exits. The results show that the error between the theoretical emergency evacuation time and simulation evacuation time was 5.4%, The emergency evacuation model established in this study boasts strong robustness and stability.

Fires are complex multi-physics problems that span wide spatial scale ranges. Capturing this complexity in computationally affordable numerical simulations for process studies and “outer-loop” techniques (e.g., optimization and uncertainty quantification) is a fundamental challenge in reacting flow research. Further complications arise for propagating fires where a priori knowledge of the fire spread rate and direction is typically not available. In such cases, static mesh refinement at all possible fire locations is a computationally inefficient approach to bridging the wide range of spatial scales relevant to fire behavior. In the present study, we address this challenge by incorporating adaptive mesh refinement (AMR) in fireFoam, an OpenFOAM solver for simulations of complex fire phenomena involving pyrolyzing solid surfaces. The AMR functionality in the extended solver, called fireDyMFoam, is load balanced, models gas, solid, and liquid phases, and allows us to dynamically track regions of interest, thus avoiding inefficient over-resolution of areas far from a propagating flame. We demonstrate the AMR capability and computational efficiency for fire spread on vertical panels, showing that the AMR solver reproduces results obtained using much larger statically refined meshes, but at a substantially reduced computational cost. We then leverage the computational efficiency of the AMR solver to demonstrate an optimization framework for fire suppression based on the open-source Dakota toolkit.

The aim of this study is to model hydrodynamic processes of the Istanbul Strait with its stratified flow characteristic and calibrate the most important parameters using local and global search algorithms. For that two open boundary conditions are defined, which are in the North and South part of the Strait. Observed bathymetric, hydrographic, meteorological and water level data are used to set up the Delft3D-FLOW model. First, the sensitivities of model parameters on the numerical model outputs are assessed using PEST toolbox. Then, the model is calibrated based on the objective functions focusing on the flowrates of upper and lower layers. The salinity and temperature profiles of the Strait are only used for model validation. The results show that the calibrated model outputs of Istanbul Strait are reliable and consistent with the in-situ measurements. The sensitivity analysis reveals that the Spatial Low-Pass Filter Coefficient, Horizontal Eddy Viscosity, Prandtl-Schmidt Number, Slope in log-log Spectrum and Manning Roughness Coefficient are most sensitive parameters affecting flowrate performance of the model. The agreement between observed salinity profiles and simulated model outputs is promising whereas the match between observed and simulated temperature profiles is weak showing that the model can be improved particularly for simulating the mixing layer.

The popularity and growth of additive manufacturing(AM) in recent years are due to its ability to provide innovative solutions to complex manufacturing challenges and its potential to transform the way products are designed, developed, and produced. In this work, the numerical simulation geometry of the model extruder from nozzle is established along with the material extrusion process. The high gravity material extrusion system (HG-MEX) properties and characteristics during filament fabrication are evaluated. This work investigates the effects of gravity on the material extrusion process from nozzle extrusion. This work is unique in the incorporation of fluid surface characteristics to represent the performance and contact with the material extrusion in additive manufacturing. The use of simulation in high gravity material extrusion in additive manufacturing is a meaningful and valuable approach to improving the quality and efficiency of the process.

For the polymer electrolyte fuel cell (PEFC), the separator thickness plays an important role to determine the weight, the volume and the costs of the PEFC. In addition, thermal management, i.e. temperature distribution is also important for the PEFC system to obtain higher performance. However, there were few reports investigating the relationship between the temperature distribution and the power generation performance such as current density distribution of PEFC operated at higher temperature (HT-PEFC). The aim of this study is to clarify the impact of separator thickness on the relationship between the temperature distribution and the current density distribution of HT-PEFC. This study has also investigated the impact of separator thickness on the relationship between the temperature distribution and the gases such as H2, O2 and the current density distribution of HT-PEFC numerically using CFD software COMSOL Multiphysics. The separator thicknesses of 2.0 mm, 1.5 mm and 1.0 mm were studied. In the study, the operation temperature and the relative humidity (RH) of supply gas were also changed. As a result, it was revealed that the optimum separator thickness was 2.0 mm to obtain higher power generation of HT-PEFC. Since the heat capacity in the case of the separator thickness of 2.0 mm was the largest among the separators investigated in this study, the dehydration of PEM and catalyst layer was smaller compared with the thinner separator thicknesses. It was also revealed that the impacts of separator thickness on distribution of gases, e.g. O2, H2O, and current density distribution became larger under higher temperature and lower RH conditions. This study also concluded that the tendency of temperature distribution matched those of O2, H2O and current density distributions.

The scope of this work was part of our previous research on Pulsed Power Plasma Stimulation Technique. Electromagnetic fields generated during a pulsed power plasma discharge were simulated using a finite element method in the COMSOL RF module. The field distributions were calculated during and after the pulse. The current paper takes advantage of prior work measuring and modeling the current distribution in the plasma arc. Agreement with laboratory experimental measurements provides support for extension of the model to reservoir scale. The validated model was used to quantify the signal attenuation level in different medium environment.

Motivated by the way animals react in nature, we introduce a fully-connected neural-network model, which incorporates the external pattern presented to the system as a fundamental tool of the recognition process. In this new scenario, in the absence of this external field, memories are not attractors inside basins of attraction, as in usual attractor neural networks, although basins may be created according to the external pattern, thus allowing storing a much larger number of memories. The key point consists in calibrating the influence of the external pattern such as to cancel the noise generated by those memories not correlated with the external pattern.We illustrate how this proposal works by including this new contribution in the standard Hopfield model, showing a significant increase in its recognition capacity (typically by a factor $10^{2}$). As an additional feature of this model, we show its ability to react promptly to changes in the external environment, a crucial attribute of living beings. This procedure can be applied to a wide variety of neural-network models to increase considerably their recognition and reaction capabilities.

Rapidly spreading disease, COVID-19 is classified as the human-to-human transmission-able disease and currently is a pandemic in the Globe. In this paper, we propose conceptual mathematical models for COVID-19 outbreak and it's control measurement; quarantine, hospitalization and the effect of panic and anxiety. In this situation, mathematical models are a important tool to employ an effective strategy in order to fight against this pandemic. We establish the positivity and boundedness of solutions, local and global stability analysis of equilibria to examine its epidemiological relevance. To validate the model and estimating the important model parameters and prediction about the disease, we consider the real cases of Italy from $15^{th}$ Feb to $13^{th} $ April 2020. In a series of graphical map, we have presented the comparative study to estimate the current scenarios and to predict the control measurement time boundary of the outbreak.

Plastic pollution of the ocean is currently one of the most serious environmental threat. Analysis of observations in the Arctic ocean shows that microplastic particles have been found in Arctic snow cover, sea ice, water and sediments. Possible pathways and deposition locations of microplastics in the Arctic Ocean can be assessed based on 3D numerical modeling of thermohaline structure and water circulation, sea ice conditions and drift. The problem is that in addition to transport by currents, a number of other processes affect the state of microplastics. These include mechanical fragmentation, freezing into sea ice and release back into the water, biofouling, adsorption of contaminants and other factors. In this study, based on scenario calculations for a 5-year period, we analyzed the possible spread of microplastics brought by Siberian rivers to the Kara Sea shelf. The Lagrangian particle model used daily 3D numerical simulation data to simulate microplastic transport by ocean currents and by sea ice drift. The results of a series of scenario calculations show how the distribution of particles and their subsequent deposition depend on their type (density), size, processes of freezing into the ice and biofouling.

This article presents the impact analysis of space harmonics (SH) presence on a single-sided three-phase linear induction motor, along with a comprehensive parametric investigation. The presence of SH often reduces the LIM performances. The electromagnetic phenomena are governed by Maxwell's equations associated with equivalent circuit modelling. The chosen mathematical model uses 2D formulation with magnetic vector potential A. The model implementation is performed with finite element method on Gmsh-GetDP free platform. The electromagnetic thrust is calculated in current excitation case by a numerical model (FEM) with and without term generating SH in order to highlight the effect of SH. The adaptation to voltage supply operation is obtained by equivalent electric circuits (EEC), through calculation of the operational impedance. The main objective of the study consists in a comparative exploration of SH presence using two numerical models (single and multi-harmonics), and an assessment of parameters effect on space harmonic presence and various machine characteristics such as thrust, efficiency, and power factor. The motor’s characteristics (ie: thrust, efficiency and power factor) strongly depend on parameters such as the pole pair number and conductivity. Improving the operation and maximizing the performances of such a machine for a given specification requires the use of optimization algorithms.

We measure the accelerated cosmic expansion rate of the late-time Universe and derive constraints on cosmological parameters from the final baryon acoustic oscillation (BAO) uncorrelated measurements of different surveys after two decades of dedicated spectroscopic observation combined with the Pantheon sample of Type Ia supernovae, the Hubble diagram of gamma-ray bursts & quasars data, the Cosmic Chronometers data, and the recent Hubble constant value measurement from the Hubble Space Telescope and the SH0ES Team as an additional prior. In Λ cold dark matter (ΛCDM) scenario, the model fit yields Ωm=0.313±0.034 and ΩΛ=0.672±0.025. Combining BAO with CC+Pantheon+QSR+GRB data sets we get H0=69.21±1.22 km s−1 Mpc−1, rd=133.46±2.49 Mpc. For the a flat wCDM model, we get w=−1.111±0.030. For a dynamical evolution of dark energy in a flat w0waCDM cosmology, we get wa=−0.292±0.167. We apply the Akaike information criteria probe to compare the three models, and see that all models are favored and cannot be discarded from the current data.

The annual energy matrix has been changing in the last years because of the necessity of less dependence on fossil fuels, which are running out on the planet. Therefore, a study was started to simulate the most efficient production of H2 through COMSOL Multiphysics®, as it is a gas that in the future will be essential to supply the world's energy necessities, due to its easy to get and insert in piped gas pipes. From this study, we were able to present an optimization of parameters that presents good indications of how to obtain efficient hydrogen production in an idealized reactor.

A method for solving the turbulence equations embedded in the sigma ocean general ocean circulation model is proposed. Like the general circulation model, the turbulence equations are solved using the splitting method by physical processes. The turbulence equations are split into two main stages describing transport-diffusion and generation-dissipation processes. Parameterization of turbulence in the framework of equations allows, at the generation-dissipation stage, to use both numerical and analytical solutions and to ensure high efficiency of the algorithm. The results of large-scale ocean dynamics simulation taking into account the parameterization of vertical turbulent exchange are considered. Numerical experiments were carried out using k-omega turbulence model embedded to the Institute of Numerical Mathematics Ocean general circulation Model (INMOM). Both the circulation and turbulence models are solved using the splitting method with respect to physical processes. The coupled model is used to simulate the hydrophysical fields of the North Atlantic and Arctic Oceans for 1948--2009. The model has a horizontal resolution of 0.25 degree and 40 sigma-levels along the vertical. The sensitivity of the solution to the changes in mixing parameterization is studied. Experiments demonstrate that taking into account the climatic annual mean buoyancy frequency improves the reproduction of large-scale ocean characteristics. There is a positive effect of Prandtl number variations for reproducing the upper mixed layer depth. The experiments also demonstrate the computational effectiveness of the proposed approach in solving the turbulence equations.

In the present paper, laminar forced convection nanofluid flows in a uniformly heated horizontal tube were revisited by direct numerical simulations. Single and two-phase models were employed with constant and temperature-dependent properties. Comparisons with experimental data showed that the mixture model performs better than the single-phase model in the all cases studied. Temperature-dependent fluid properties also resulted in a better prediction of the thermal field. A particular attention was paid to the grid arrangement. The two-phase model was used then confidently to investigate the influence of the nanoparticle size on the heat and fluid flow with a particular emphasis on the sedimentation process. Four nanoparticle diameters were considered: 10, 42, 100 and 200 nm for both copper-water and alumina/water nanofluids. For the largest diameter dnp = 200 nm, the Cu nanoparticles were more sedimented by around 80 %, while the Al₂O₃ nanoparticles sedimented only by 2.5 %. Besides, it was found that increasing the Reynolds number improved the heat transfer rate, while it decreased the friction factor allowing the nanoparticles to stay more dispersed in the base fluid. The effect of nanoparticle type on the heat transfer coefficient was also investigated for six different water-based nanofluids. Results showed that the Cu-water nanofluid achieved the highest heat transfer coefficient, followed by C, Al₂O₃, CuO, TiO₂, and SiO₂, respectively. All results were presented and discussed for four different values of the concentration in nanoparticles, namely φ = 0, 0.6, 1 and 1.6%. Empirical correlations for the friction coefficient and the average Nusselt number were also provided summarizing all the presented results.

With the popularization of natural gas and the requirements for environmental protection, the development and utilization of natural gas is particularly important. The status of natural gas in China's oil and gas exploration and development is constantly improving, and the country is paying more and more attention to the exploitation and utilization of natural gas. The Upper Paleozoic tight sandstone in the Ordos Basin is characterized by low porosity, low permeability and large area of concealed gas reservoirs. By injecting CO2 into the formation, the recovery of natural gas can be improved, and at the same time, the stable storage of CO2 can be achieved to achieve a win-win situation of CO2 emission reduction and utilization. Injecting greenhouse gas CO2 into gas reservoirs for storage and improving recovery has also become a hot research issue. In order to improve the recovery efficiency of tight sandstone gas reservoir, this paper takes the complex tight sandstone of Upper Paleozoic in Ordos Basin as the research object, through indoor physical simulation experiments, carried out the influence of displacement rate, fracture dip angle, core permeability, core dryness and wetness on CO2 gas displacement efficiency and storage efficiency, and analyzed the influence of different factors on CO2 gas displacement efficiency and storage efficiency to improve the recovery and storage efficiency. The research results show that under different conditions, when the CO2 injection pore volume is less than 1PV, the relationship between the CH4 recovery rate and the CO2 injection pore volume is linear, and the tilt angle is 45 °. When the CO2 injection pore volume exceeds 1PV, the CH4 recovery rate increases slightly with the increase of displacement speed, the recovery rate of CO2 displacement CH4 is between 87% - 97%, and the CO2 breakthrough time is 0.7PV-0.9PV. In low-permeability and low-speed displacement cores, the diffusion of CO2 molecules is more significant. The lower the displacement speed is, the earlier the breakthrough time of CO2 is, and the final recovery of CH4 slightly decreases. Gravity has a great impact on CO2 storage and enhanced recovery. The breakthrough of high injection and low recovery of CO2 is earlier, and the recovery of CH4 is about 3.3% lower than that of low injection and high recovery. The bound water makes the displacement phase CO2 partially dissolved in the formation water, and the CO2 breakthrough lags about 0.1PV. Ultimately, CH4 recovery factor and CO2 storage rate are higher than those of dry core displacement. The research results provide theoretical data support for CO2 injection to improve recovery and storage efficiency in complex tight sandstone gas reservoirs.

In order to reveal the mechanism and influencing factors of high pressure jet cavitation of nozzle in submerged environment, this study focused on the evolutionary process of cavitation bubbles and combined finite volume method and mixed multi-phase flow model to analyze the cavitation, velocity distribution and experimental cavitation intensity of fishing net cleaning equipment. Results show that the cavitation inception, growth and collapse mainly occurred in the peripheral region of the flow field. Ring-shaped cavitation erosion zone appeared on the test sample target. A lot of small dense erosion pits were densely distributed in the ring-shaped erosion zone, erosion marks were observed in the center. The cavitation erosion intensity was greatly affected by the nozzle structure. As the diameter of nozzle increased from 0.6 mm to 1 mm, the maximum gas volume fraction increased by 8.53%. The nozzle outlet enlargement angle greatly increased the cavitation intensity. The nozzle with an outlet angle of 30° exhibited the optimal cavitation erosion performance . The cavitation volume fraction of the nozzle with short necking structure was slightly larger than that of the nozzle with long necking structure at the same level in the necking length rang of 3mm to 7mm. In terms of the influence of nozzle structure on the cavitation erosion effect, the nozzle diameter D ranked the first, followed by the outlet angle α, and the necking length L was at the last.

In this paper an integrated methodology for the coupling between 1D- and 3D-CFD simulation codes is presented, which has been developed to support the design and calibration of new diesel engines. The aim of the proposed methodology is to couple 1D engine models, which may be available in the early-stage engine development phases, with 3D predictive combustion simulations, in order to obtain reliable estimates of engine performance and emissions for newly designed automotive diesel engines. The coupling procedure features simulations performed in 1D-CFD by means of GT-SUITE and in 3D-CFD by means of Converge, executed within a specifically designed calculation methodology. An assessment of the coupling procedure has been performed by comparing its results with experimental data acquired on an automotive Diesel engine, considering different working points including both part load and full load conditions. Different multiple injection schedules have been evaluated for part-load operation, including pre and post injections. The proposed methodology, featuring detailed 3D chemistry modeling, was proven to be capable to properly assess pollutant formation, specifically to estimate NOx concentrations. Soot formation trend was also well-matched for most of the explored working points. The proposed procedure can therefore be considered as a suitable methodology to support the design and calibration of new Diesel engines, thanks to its ability to provide reliable engine performance and emissions estimations from the early-stage of a new engine development.

Taking a certain type of test centrifuge as the research object, the finite element model of the test centrifuge is established, the vibration characteristics and aerodynamic performance of the test centrifuge are analyzed, and the structural optimization design of the test centrifuge is carried out. In this paper, the load is applied according to the actual working condition of a certain type of test centrifuge. The vibration of the mounting seat of the test centrifuge is analyzed and the structure of the mounting seat is optimized. After optimization, the vibration of the mounting seat is 77.38 % lower than that of the original mounting seat. Then, the aerodynamic analysis of the test centrifuge is carried out. The analysis results show that the test centrifuge moves more smoothly under the whole package shell and the steady flow shell, and the resistance decreases and the shaft load decreases. Finally, the steady flow shell of the test centrifuge is optimized. The analysis shows that the increase of the width of the steady flow shell can reduce the resistance coefficient, which is helpful to the stability of the test centrifuge during operation and reduces the unbalanced response of the system caused by air resistance.

The present work is focused on the numerical solution of the complete energy equation used in fluid film lubrication. The work was motivated by the fact the complete energy equation has no analytic solution that could be used for validations. Its accuracy and computation time are related to the employed numerical method and to the grid resolution. The natural discretization method (NDM) applied on different grids is systematically compared with the spectral method (the Lobatto Point Colocation Method or LPCM) with different polynomial degrees. A one dimensional inclined slider is used for the numerical tests and the energy equation is artificially decoupled from Reynolds. This approach enables to focus all the attention on the numerical solution of the energy equation. The results show that the LPCM is one or two orders of magnitudes more efficient than the NDM in terms of computation time. The energy equation is then coupled with Reynolds equation in a thermo-hydrodynamic analysis of the same 1D slider; the numerical results confirm again the efficiency of the LPCM. A thermo-hydrodynamic analysis of a two-lobe journal bearing is then presented as a practical application.

Distributions with bounded support show considerable sparsity over those with unbounded support, despite the fact that there are a number of real-world contexts where observations take values from a bounded range (proportions, percentages, and fractions are typical examples). For proportion modelling, a flexible family of two-parameter distribution functions associated with the exponential distribution is proposed here. Mathematical and statistical properties of the novel distribution are examined, including quantiles, mode, moments, hazard rate function, and its characterization. The parameter estimation procedure using the maximum likelihood method was carried out, and applications to environmental and engineering data were also considered. To this end, various statistical tests are used, along with some other information criterion indicators to determine how well the model fits the data. The proposed model is found to be the most efficient plan in most cases for the datasets considered.

FRAP technique have been used for decades to measure movements of molecules in 2D. Data obtained by FRAP experiments in cell plasma membranes are assumed to be described through means of two parameters, a diffusion coefficient D (as defined in a pure Brownian model) and a mobile fraction M. Nevertheless, it has also been shown that recoveries can be nicely fit using anomalous sub-diffusion. FRAP at variable radii has been developed using the Brownian diffusion model to access geometrical characteristics of the surrounding landscape of the molecule. Here we performed numerical simulations of continuous time random walk (CTRW) anomalous subdiffusion and interpreted them in the context of variable radii FRAP. These simulations were compared to experimental data obtained at variable radii on living cells using the PH domain of the membrane binding protein EFA6 (exchange factor for ARF6, a small G protein). This protein domain is an excellent candidate to explore the structure of the interface between cytosol and plasma membrane in cells. By direct comparison of our numerical simulations to the experiments, we show that this protein does not exhibit anomalous diffusion in BHK cells. The non Brownian PH-EFA6 dynamics observed here is more related to spatial heterogeneities such as cytoskeleton fences effects.

The educational and play-related activities of children are proceeded mainly indoors in a kin-dergarten. The exposure of children to high concentrations of PM2.5 and CO2 indoors have leaded to various harmful effects and negatively impact educational outcomes in a kindergarten. Therefore, this study presents a numerical model of CO2 and PM2.5 concentration based on two classrooms in a kindergarten. Using this numerical model, we present different scenarios of oper-ating mechanical ventilation and air purifiers in kindergartens with the aim of optimizing for reducing the concentrations of CO2 and PM2.5. We found that the amount of ventilation required to maintain good air quality, per child, was approximately 20.4 m3/h. However, we also found that as the amount of ventilation increased, so did the concentration of indoor PM2.5; we found that this issue can be resolved through the use of a high-grade filter (i.e., a MERV 13 grade filter with a collection efficiency of 75%). This study provides a scientific basis for reducing PM2.5concentrations in kindergartens, while keeping CO2 levels low.

ABSTRACT. In this paper, we suggest a biomathematical numerical method for analysing mRNA nucleotides sequences based on UA/CG Fibonacci numbers proportions. This method is used to evaluate then compare the spike genes related to the main SARS-CoV2 VARIANTS currently circulating within the world population. The 10 main results proposed to be reproduced by peers are: 1/ SARS-CoV2 genome and spike evolution in one year 2020-2021. 2/ SARS-CoV2 Origins. 3/ Comparing 11 reference variants spikes. 4/ analysing 32 CAL.20C California variant patients spikes. 5/ Toward a meta mRNA Fibonacci gene end message code. 6/ Analysing S501 UK, S484 South Africa and « 2 mutations » INDIA variants. 7/ Suggesting a possible variants spike mRNA palindrome symmetry metastructure improving mRNA stability then infectiousness. 8/ Analysing Fibonacci Metastructures in the mRNA coding for the vaccines PFIZER and MODERNA. 9/ Does the CG-rich modification of the synonymous codons of the spikes of the 2 mRNA vaccines affect the expression and quantity of SARS-CoV2 antibodies? 10/ The exceptional case of the Brazilian variant P.1. Particularly, we suggest the following conjecture at mRNA folding level : CONJECTURE of SARS-CoV2 VARIANTS: The growth of long Fibonacci structures in the shape of "podiums" for almost all of the variants studied (UK, California, South Africa, India, etc.) suggests the probable folding of the Spike mRNA in the form of a "hairpin", which can strengthen the cohesion and the lifespan of this mRNA. Finally, we show that these kinds of Fibonacci matastructures disapear TOTALLY by analysing the published mRNA sequences of PFIZER and MODERNA vaccines. One fact is certain, the two mRNAs of the Moderna and Pfizer vaccines will result in a low functionality of the spike vaccine. This is because their designers by seeking greater stability, have doped to build CG rich sequences which, as soon as they are inserted into the human host, will, paradoxically, seek to mutate, like SARS-CoV2 variants, towards CG ==> UA forms in order to improve their STABILITY and LIFETIME. We conclude using new biomathematics theoretical methods (Master code and numerical standing waves), and comparing the Spikes of the two vaccines Moderna and Pfizer, that there will be very probable differences in stability and shelf life of the two respective mRNAs vaccines. However, “State of the Art” analyzes will disclose that their two protein sequences are strictly identical. By modified their synonymous codons using different strategies, no one can guarantee that the quantity of antibodies generated will be identical in the two cases. We wish to draw attention to the great ADAPTATION power - at the global scale of their genomes - of the most infectious VARIANTS, such as the BRAZIL 20J / 501Y.V3 variant (P.1). This is very worrying for the VACCINES <==> VARIANTS run: We demonstrate how the Brazilian variant P.1 which becomes uncontrollable in Brazil in April 2021 has a level of organization of long metastructures of 17,711 bases covering the genome which is 3.6 more important than that of the 2 reference genomes SARS-CoV2 and worldwide D614G. We suggest that this high level of overall structure of this variant contributes to the stability of this genome and, might explain its greater contagiousness.

Paper is a material whose mechanical properties are highly dependent on humidity and temperature. Which naturally also builds the relationship between the stiffness and strength of corrugated board and changing weather conditions. In this paper, attention is focused on the dependence of the physical properties of the cardboard on changes in humidity and temperature, which undergo dynamic fluctuations both during the production of corrugated board and during its storage. Two techniques were used to test this effect, namely numerical homogenization and global sensitivity analysis. Both methods were implemented to determine the theoretical relationships between the change in humidity and/or temperature in each layer of corrugated board and its global bending, compression and shear stiffness. The procedure was used to analyze different types of 5-ply and 3-ply cardboard. The obtained results allowed to build a complete map of the relationship between the change in humidity of selected layers and the strength characteristics of the full assembly.

Energy dissipation is one of the most important factors in choosing stepped spillways. However, few studies are about energy dissipation with different horizontal face angles. In this paper, the realizable k-ε turbulence model was used to study the flow field and energy dissipation rates of different stepped spillways with five horizontal face angles in the skimming flow regions. It shows that the free water surfaces and energy dissipation rates change with horizontal face angles and the energy dissipation rates initially decrease and then increase as the horizontal face angle increases. And the horizontal face angles cause the great changes of flow field.

This is the second in a series of two articles introducing the Gravitas computational general relativity framework, in which we now focus upon the design and capabilities of Gravitas's numerical subsystem, including its ability to perform general 3+1 decompositions of spacetime via the ADM formalism, its support for the definition and construction of arbitrary Cauchy surfaces as initial data, its support for the definition and enforcement of arbitrary gauge and coordinate conditions, its various algorithms for ensuring the satisfaction of the ADM Hamiltonian and momentum constraints, and its unique (totally-unstructured) adaptive refinement algorithms based on hypergraph rewriting via Wolfram model evolution. Particular attention will be paid to the seamless integration between Gravitas's symbolic and numerical subsystems, its ability to configure, run, analyze and visualize complex numerical relativity simulations and their outputs within a single notebook environment, and its capabilities for handling generic curvilinear coordinate systems and spacetimes with general (and often highly non-trivial) topologies using its specialized and highly efficient hypergraph-based numerical algorithms. We also provide illustrations of Gravitas's functionality for the visualization of hypergraph geometries and spacetime embedding diagrams in two and three dimensions, the ability for Gravitas's symbolic and numerical subsystems to be used in concert for the extraction of gravitational wave signals and other crucial simulation data, and Gravitas's in-built library of standard initial data, matter distributions and gauge conditions. We conclude by demonstrating how the numerical subsystem can be used to set up, run, visualize and analyze a standard yet nevertheless reasonably challenging numerical relativity test case: a binary black hole collision and merger within a vacuum spacetime (including the extraction of its outgoing gravitational wave profile).

The damage evolution rules of coal under true triaxial combined static-dynamic loads are important to understand and reveal the mechanism of rockburst in coal mines. The numerical simulation was carried out using FLAC3D to explore the coupling effect of static and dynamic stress, especially the influence of dynamic load parameters. The results show that the increase of dynamic load amplitude not only makes the plastic zone grow exponentially and shorten the damage development time, but also decreases the residual strength of the coal sample, which leads to a much more violent of the dynamic failure. The stress wave can propagate more stable in the coal sample with the increase of dynamic load frequency and the development time of the plastic zone also show synchronous fluctuating features, and when the frequency is like the intrinsic frequency of the coal sample, the dynamic load has a significant stimulate effect. The static and dynamic loads have different damage effect to the coal sample under true triaxial stress path, the weight decreases in order of the minimum principal stress, the maximum principal, the amplitude of the dynamic load and at last the dynamic stress frequency by the entropy weight method analysis.

Folk residence in the cold region of Northeast China is an important part of China's traditional folk residence, with significant geographical representation. In this paper, we take the residential compounds of villages and towns in the cold region of Northeast China as the research object, summarize four typical layout forms of residential compounds of villages and towns in the cold region of Northeast China, simulate the wind environment of compounds of different layout forms in winter by using the computer numerical simulation software Fluent, and then analyze and evaluate the wind environment of compounds by combining with the evaluation standard of wind speed ratio and considering the area of wind shadows, number of vortices and other factors.

Typhoid fever is an infectious disease that affects humanity worldwide particularly in the lower socio-economic communities where many individuals are exposed to a dirty environment and unclean food. A mathematical model is formulated to analyze the impact of control measures such as vaccination of susceptible humans, treatment of infected humans and sanitation in the different socio-economic communities. The model assumed that the population comprises of two socio-economic classes. The essential dynamical system analysis of our model was appropriately carried out. The impact of the control measures was analyzed, and the optimal control theory was applied on the control model to explore the impact of the different control measures. Numerical simulation of the models and the optimal controls were carried out and results obtained indicates that the overall combination of the control measures eradicates Typhoid fever in the population but the controls are more optimal in the higher socio-economic communities.

The steady streaming (SS) phenomenon is gaining increased attention in the microfluidics community, because it can generate net mass flow from the zero-mean vibration. We developed numerical simulation and experimental measurement tools to analyze this vibration induced flow, which has been challenging due to its unsteady nature. Validity of these analysis methods is confirmed by comparing the three-dimensional (3D) flow field induced around a cylindrical micropillar under circular vibration. In the numerical modeling, we directly solved the flow in the Lagrangian frame so that the substrate with a micropillar becomes stationary, and the result was converted to the Eulerian frame to compare them with the experimental results. The present approach enables to avoid the introduction of moving boundary or small perturbation approximation. The flow field obtained by the micro particle image velocimetry (PIV) measurement supported the three-dimensionality observed in the numerical results, which could be important for controlling the mass transport and manipulating particulate objects in the microfluidic systems.

In this work, new refinements of some numerical radius inequalities are proved. Namely, new improvements and refinements purify the recent inequalities of some famous inequalities concerning the numerical radius of Hilbert space operators. The proven inequalities in this work are not only an improvement over old inequalities, but rather they are stronger than them. Several examples that support the validity of our results are established as well.

The paper continues the study of efficient algorithms for the computation of zeta functions over the complex plane. We aim to apply the modifications of algorithms to the investigation of underlying fractal structures associated with the Riemann zeta function. We discuss the computational complexity and numerical aspects of the implemented algorithms based on series with binomial-like coefficients.

Some cognitive functions, shared by humans and certain animals, were acquired early in the course of phylogeny and, in humans, are operational in their primitive form shortly after birth. This is the case for the quantification of discrete objects. The further phylogenetic evolution of the human brain allows such functions to be reconstructed in a much more sophisticated way during child development. Certain functional characteristics of the brain (plasticity, multiple cognitive processes involved in the same response, interactions and substitution relationships between those processes) provide degrees of freedom that open up the possibility of different pathways of reconstruction. The within- and between-individual variability of these developmental pathways offers an original window on the dynamics of development. Here, I will illustrate this theoretical approach to cognitive development—which can be called “reconstructivist” and “pluralistic”—using children's construction of number as an example.

By installing FBG sensors on the geogrids, smart geogrids can both reinforce and monitor the stability for geogrid-reinforced slopes. In this paper, a geogrid-reinforced sand slope model test was conducted in the laboratory and fiber Bragg grating (FBG) sensing technology is used to measure the strain distribution of the geogrid. Based on the model test, the performance of the reinforced soil slope is simulated by finite element software Midas-GTS, and the stability of the reinforced soil slope is analyzed by strength reduction method. The relationship between the geogrid strain and safety factor is set up. The results indicate that the measured strain and calculated results agree very well. The geogrid strain measured by FBG sensor can be applied to evaluate the stability of geogrid-reinforced sand slopes.

On the basis of the force and safety factor analysis of traditional retaining wall, a new analytical method of force and displacement of slope is suggested, the numerical theoretical solution of the stress distribution of the sliding body can be obtained under the conditions, which the stresses distribution are satisfied with the differential equilibrium equations, the boundary conditions, the compatibility equation and the macroscopic equilibrium equations. The interface stresses between the sliding body and the retaining wall are continuous, the theoretical solution of retaining wall stress distributions can be gotten, while the stress differential equilibrium equation, the compatibility equation, macroscopic force and moment balance equations are satisfied. The strain and displacement solutions can be obtained by using Duncan Chang and Hooke constitutive equations for the slope and the retaining wall respectively. The transfer station of landfill in the Guandukou Town of Badong County is taken as an example, the results of the sliding body and retaining wall analysis show: The stress and strain solutions of a slope and a retaining wall can be obtained by the proposed method, the forces between the retaining wall and the sliding body include shear stress and normal stress, and the stress distributions change with the deformation of the sliding body, the shape and material of retaining wall can be optimized according to the calculation results，it is feasible for the proposed analysis method of slope with retaining wall design to be run many years.

Large aluminum alloy ring forgings are the core components of heavy-duty rocket fuel storage tanks, and the large residual stress inside the rings leads to poor shape accuracy of large thin-walled parts. The initial stress of the 2219 aluminum alloy ring blank was tested using the drilling method, and the creep constitutive coefficient of the 2219 aluminum alloy was determined through stress relaxation tests. The numerical simulation processes of thermal stress relief (TSR), vibration stress relief (VSR), and thermal-vibration stress relief (TVSR) were compared and established. Through the correlation analysis between the actual measurement results of residual stress and the simulation results, it can be seen that the strong correlation in three directions at each measurement point accounts for over 37.5%, and the moderate correlation accounts for over 62.5%. This indicates that the numerical simulation model of 2219 aluminum alloy ring containing initial residual stress can accurately reflect the size and distribution of residual stress inside the actual ring. The simulation results show that the derived constitutive model can describe the stress relaxation process of TVSR by combining a single thermal time effect stress relaxation constitutive theory with a VSR plastic deformation material model. The simulation models established above were used to calculate the residual stress homogenization ability of three types of aging. The results showed that VSR, TSR, and TVSR can homogenize and reduce the residual stress field inside the ring, improve the distribution of residual stress inside the ring, and have a better overall homogenization ability of TVSR. The VSR control has a certain effect on reducing and homogenizing residual stress, but compared with TSR and TVSR, the reduction and homogenization ability of residual stress control is limited. The homogenization control effect TVSR>TSR>VSR, and the maximum equivalent stress homogenization rates of VSR, TSR, and TVSR are 52.8%, 80.6%, and 82.2%, respectively. Then, numerical simulation technology is used to study how the initial residual stress in the blank will cause the deformation of the ring during the thin-walled machining process. The roundness error theory of the minimum containment area method is applied to evaluate the deformation degree during the thin-walled numerical machining process, and the TVSR method is used for stress regulation. The deformation law of the thin-walled machining of the ring under different aging parameters is studied.

The soil-structure interaction represents an important parameter when analyzing the dynamic behavior of bridges, taking into account the integration between soil, foundation, and structure to ensure an adequate structural representation. In this paper, a computational modeling strategy using soil-structure interaction (SSI) methodology was applied to represent the dynamic behavior of a pedestrian bridge (LOP). The computational models were validated using monitoring results from an extensive structural health monitoring campaign. The bridge monitoring program was characterized using embedded sensors and cutting-edge technology for remote monitoring: ground-based radar interferometry and video motion amplification. The instrumentation results were compared to establish the capabilities and advantages of this novel remote monitoring technique. The experimental results obtained from free and forced vibrations in the asset served as a basis for validating the developed computational model and allowed evaluating the asset be-havior in service for different loading conditions. This paper emphasizes the SSI approach to represent the pedestrian bridge dynamic behavior more accurately, allowing computational models to represent the LOP structural responses over the course of its life-cycle.

The problems of formation and propagation of surface seismic waves in vertically layered and horizontally inhomogeneous media are studied. A mathematical model has been developed for the propagation of surface seismic waves in an inhomogeneous medium based on the use of the fundamental principles of wave dynamics and Fourier transforms. The existence of various types of groups of these waves is proved, and their main properties are studied. It has been established that the reflection coefficients of different groups of a dispersive wave on models of half-spaces (a layered, inhomogeneous medium) with a sharp velocity differentiation are characterized by the same dependence on the angle of incidence as in the absence of dispersion. In the region of the critical angle, which depends on the period of the incident wave, a local decrease in the intensity of wave reflection is observed, which is associated with the origin of the head dispersive wave. It has been found that the reflection coefficients of Rayleigh waves from low-velocity layers, thin (d / λ2 = 0.205) and thick (d / λ2 = 0.82) are approximately 0.2 ± 0.04 and practically do not change with increasing angle of incidence. On the basis of theoretical studies, it was revealed that reflected surface waves carry information both about the elastic properties of the reflecting medium and about the dimensions of the reflecting horizontal inhomogeneity. An experimental dispersion curve of the group velocity of Rayleigh waves on the Central Asia-Caucasus path has been obtained. The seismic stress state of the "subgrade-base" system was studied. Based on the analysis of the results of numerical experiments, it has been established that in order to obtain a complete picture of the seismically stressed state of the subgrade, it is necessary to take into account the contribution to it of each component of the accelerogram of a real earthquake.

Air filtration mechanisms in the composite filter media used in practical applications are important and challenging to understand because the component fibers could have various size scales and morphologies. In this work, a three-dimensional digital model of nanofiber-based filter media was reconstructed for the first time based on the X-ray tomography data for the cellulose substrate and the Focused Ion Beam-Scanning Electron Microscope (FIB-SEM) image analysis for the several microns thick (3.82-7.90 μm) electrospun polyvinylidene fluoride (PVDF) nanofiber membrane. Besides the high-resolution model where the details of the fibrous structures were fully resolved, another low-resolution model with approximated unresolved structures was also established. Filtration simulations utilizing these models were conducted considering the drag force, Brownian diffusion and aerodynamic slip. The simulated filtration efficiencies agreed well with the experiments for particles of 70-400 nm, including the most penetrating particle size (MPPS, 100-200 nm). Moreover, the structure-resolved models had higher accuracy but higher computational costs, while the unresolved simulations saved much running time but over-predicted the filtration efficiency, especially for smaller particles (<100 nm). Our study presents a comprehensive strategy for investigating the composite filter media with multiscale complex structures using a combination of advanced characterization technologies and modular simulation models.

{\bf Abstract.} \\ {\bf Background:} Bangladesh hosts more than 800,000 Rohingya refugees from Myanmar. The low health immunity, lifestyle, access to good healthcare services, social-security cause this population to be at risk of far more direct effects of COVID-19 than the host population. Therefore, evidence-based forecasting of the COVID-19 burden is vital in this regard. In this study, we aimed to forecast the COVID-19 burden among the Rohingya refugees of Bangladesh to keep up with the disease outbreak's pace, health needs, and disaster preparedness. \noindent{\bf Methodology and Findings:} To estimate the possible consequences of COVID-19 in the Rohingya camps of Bangladesh, we used a modified Susceptible-Exposed-Infectious Recovered (SEIR) transmission model. All the values of different parameters used in this model were from the Bangladesh Government’s database and the relevant emerging literature. We addressed two different scenarios, i.e., the best-fitting model and good fitting model with unique consequences of COVID-19. Our best fitting model suggests that there will be good control over the transmission of the COVID-19 disease. At the end of December 2020, there will be only 169 confirmed COVID-19 cases in the Rohingya refugee camps. The average basic reproduction number ($ \mathcal{R}_{0} $) has been estimated to be 0.7563. \noindent{\bf Conclusion:} Our analysis suggests that, due to the extensive precautions from the Bangladesh government as well as other humanitarian organizations, the coronavirus disease will be under control if the maintenance continues like this. Although detailed and pragmatic preparedness should be adopted for the worst scenario.

The steel grid structure with bolted ball joints is gaining popularity in offshore platforms and aquaculture cages, but the corrosion resistance of these joints is a critical safety concern. This article introduces an innovative method to enhance the sealing performance of bolted ball joints, preventing seawater ingress and corrosion. The approach involves creating a sealed surface within the contact gap between the sleeve and connecting components. Circular grooves and sealing washers are added to both ends of the sleeve. A two-dimensional finite element analysis model of the bolted ball joint with the sealing structure was created using SOLIDWORKS and ANSYS. The study analyzes the sealing gasket's contact pressure at various compression levels and evaluates its performance with bubble tests for air tightness. Research results show a linear relationship between contact pressure and compression rate, with a sealing pressure of 5.95MPa achieved at a 14% compression rate. This simple, cost-effective sealing method effectively prevents corrosion from seawater, making it ideal for marine environments.

In the process of construction and operation of the pumping station, a large number of axial flow pumps pose a threat to the survival of fish in the natural environment. Through experiments, the survival conditions of many kinds of fish in extreme positive and negative pressure environment are explored, and -40 kPa is established as the low pressure damage threshold, which is used as a reference to analyze the probability of fish damage caused by pumps. The immersion boundary-lattice Boltzmann numerical method (LES-IB-LBM) based on large eddy simulation is used to optimize the parameters of the prototype runner of axial flow pump. A new type of runner with leading edge thickness of 11.4mm and blade cutting angle of 18 ° is optimized. This kind of runner has both hydraulic performance and fish-passing ability. The runner of the fish-friendly axial flow pump effectively guides the fish into the low risk area and reduces the risk of friction, shear and impact damage to the fish. the total impact mortality ratio of the runner of the axial flow pump before and after optimization is close to 7:1. The pressure damage analysis shows that the lowest negative pressure of the fish is -59.2 kPa, which is higher than -64.5 kPa of the prototype pump, and the highest positive pressure of the body surface is 11.8 kPa, which is lower than the 43.8 kPa of the prototype pump. Shear damage analysis shows that the fish will not be damaged by shear in the prototype pump and fish-friendly pump.

The application of numerical simulation methods for studying vertical-axis wind turbines offers significant advantages over conventional horizontal-axis wind turbines regarding wind energy utilisation, start-up wind speed, and environmental impact. This paper aims to investigate and establish the aerodynamic design performance of asymmetrical (NACA 4412) airfoils used in the application of vertical-axis wind turbines. The computational fluid dynamics (CFD) simulation uses Ansys software based on the Reynolds Averaged Navier-Stokes (RANS) equations. The aerodynamic parameters (pressure and velocity) are evaluated and compared within a range of angles of attack (AoA) 5-12 degrees at a fixed Reynolds number, as is a usual condition for wind turbine application. The lift coefficient (Cl), drag coefficient (Cd), and Cl/Cd ratio are obtained within the range AoA for the asymmetrical airfoils, and the performances have been predicted using the potential flow panel and CFD methods. This study suggests that while Xfoil may not be as precise as computational fluid dynamics (CFD), its predicted lift and drag coefficients generally align with experimental results. These help us to understand the best air-foil selection in a wind turbine application and predict its optimum AoA at which it performs at its best.

In this manuscript, an automated framework dedicated to design space exploration and design optimization studies is presented. The framework integrates a set of numerical simulation, computer-aided design, numerical optimization, and data analytics tools using scripting capabilities. The tools used are open-source and freeware, and can be deployed on any platform. The main feature of the proposed methodology is the use of a cloud-based parametrical computer-aided design application, which allows the user to change any parametric variable defined in the solid model. We demonstrate the capabilities and flexibility of the framework using computational fluid dynamics applications; however, the same workflow can be used with any numerical simulation tool (e.g., a structural solver or a spread-sheet) that is able to interact via a command line interface or using scripting languages. We conduct design space exploration and design optimization studies using quantitative and qualitative metrics, and to reduce the high computing times and computational resources intrinsic to these kinds of studies, concurrent simulations and surrogate-based optimization are used.

The energy transfer process of laser selective melting is very complex. To study the effect of la-ser selective melting on the microstructure and properties of 18Ni-300 martensitic steel, ABAQUS was used to simulate the temperature of laser cladding 18Ni-300 martensitic steel at different time points and different laser power. The results show that the cross-section shape of the molten pool changes from round to oval With the increase of laser power, the higher the peak value of temperature time curve, the greater the temperature gradient; and the laser clad-ding experiment of 18Ni-300 martensitic steel was carried out, and the microstructure and me-chanical properties of the samples under different laser power were analyzed. The results show that with the increase of laser power, the grain size of the cladding layer becomes smaller and the microstructure becomes more compact; the hardness of the side surface of the sample is higher than that of the upper surface, and the tensile strength and elongation show a trend of first increasing and then decreasing.

The assimilation of Soil Moisture and Ocean Salinity (SMOS) data into the ECMWF (European Centre for Medium Range Weather Forecasts) H-TESSEL (Hydrology revised - Tiled ECMWF Scheme for Surface Exchanges over Land) model is presented. SMOS soil moisture (SM) estimates have been produced specifically by training a neural network with SMOS brightness temperatures as input and H-TESSEL model SM simulations as reference. This can help the assimilation of SMOS information in several ways: (1) the neural network soil moisture (NNSM) data have a similar climatology to the model, (2) no global bias is present with respect to the model even if regional differences can exist. Experiments performing joint data assimilation (DA) of NNSM, 2 metre air temperature and relative humidity or NNSM-only DA are discussed. The resulting SM was evaluated against a large number of in situ measurements of SM obtaining similar results to those of the model with no assimilation, even if significant differences were found from site to site. In addition, atmospheric forecasts initialized with H-TESSEL runs (without DA) or with the analysed SM were compared to measure of the impact of the satellite information. Although, NNSM DA has an overall neutral impact in the forecast in the Tropics, a significant positive impact was found in other areas and periods, especially in regions with limited in situ information. The joint NNSM, T2m and RH2m DA improves the forecast for all the seasons in the Southern Hemisphere. The impact is mostly due to T2m and RH2m, but SMOS NN DA alone also improves the forecast in July- September. In the Northern Hemisphere, the joint NNSM, T2m and RH2m DA improves the forecast in April-September, while NNSM alone has a significant positive effect in July-September. Furthermore, forecasting skill maps show that SMOS NNSM improves the forecast in North America and in Northern Asia for up to 72 hours lead time.

We are witnessing a progressive divestment of some institutions with strong traditions and skills in physical modelling and their consequent impoverishment, to the detriment of numerical modelling. For many reasons, the economic imperatives and the exponential growth of computational means and numerical methods should certainly not be excluded. In this work, we aimed to highlight the new requirements of the recent sophisticated developments in physical modelling, precisely due to the new needs imposed on them by mathematical and numerical modelling and the growing risks in civil construction works. In this context, reflections are reported, justified by scientific and real-world examples, on the need for maintenance and reinforcement of investments in physical modelling, both to support the scientific community and to design buildings of significant economic, social and environmental impact.

In rock blasting for mining production, stress waves play a major role in rock fracturing along with explosion gases. Better energy distribution improves fragmentation and safety, lowers production costs, increases productivity, and controls ore losses and dilution. Blast outcomes vary significantly with the choice of the explosive and the properties of the rock mass encountered. This study analyzes the effects of rock mass and explosives properties on the blast outcomes through numerical simulation using data from the case study and later validates the simulation results from the field blast fragmentation. The outcomes suggest that, for a given set of rock properties, the choice of explosive has a major influence on the resulting fragmentation. Strong explosives favor large fracture extents in hard rocks, while less strong explosives offer a better distribution of explosive energy and fractures. The presence of rock structures such as rock con-tacts and joints influences the propagation of stress waves and fractures depending on the structures' material properties, intensity and orientations, and the direction and strength of the stress wave. To achieve effective fragmentation, the blast design should mitigate the effect of variability in the rock mass by ensuring adequate energy distribution within the limits of geo-metrical design.

Recently, NOAA has included GNSS (Global Navigation Satellite System) Radio Occultation (RO) data as one of the crucial long-term observables for weather and climate applications. To include more GNSS RO data in the numerical weather prediction system, the NOAA Commercial Weather Data Pilot program (CWDP) started to explore the commercial RO data available on the market. After two rounds of pilot studies, the CDWP decided to award the first Indefinite Delivery Indefinite Quantity (IDIQ) contract to GeoOptics and Spire Incs. in 2020. This study examines the quality of Spire data products for weather and climate applications. Spire RO data are collected from commercial CubeSats through careful comparison with the data from Formosa Satellite Mission 7–Constellation Observing System for Meteorology, Ionosphere, and Climate-2 (COSMIC-2), ERA-5, and high-quality radiosonde data. The results demonstrated that although with lower Signal-Noise-Ratio (SNR) in general, the pattern of the lowest penetration height for Spire is similar to those for COSMIC-2. The Spire and COSMIC-2 penetrate heights are between 0.6 and 0.8 km altitude at the tropical oceans. Although using different GNSS RO receivers, the precision of Spire STRASP receivers is of the same quality as those of COSMIC-2 Global Positioning System - GPS, GALILEO, and GLObal NAvigation Satellite System – GLONASS (TGRS) receivers. The retrieval accuracy from Spire is very compatible with those from COSMIC-2. We validated Spire temperature and water vapor profiles by comparing them with collocated radiosonde data. Generally, over the height region between 8 km and 16.5 km, the Spire temperature profiles match those from RS41 RAOB very well with temperature biases &lt; 0.02 K. Over the height range from 17.8 to 26.4 km, the temperature differences are ~-0.034 K with RS41 RAOB being warmer. We also estimated the error covariance matrix for Spire, COSMIC-2, and KOMPSAT-5. Results showed that the COSMIC-2 estimated error covariance values are slightly more significant over the oceans at the mid-latitudes (45oN-30oN and 30oS-45oS), which may also be owing to COSMIC-2 SNR being lower at those latitudinal zones.

Studies on the detection of layers with elevated black carbon aerosol (BC) concentrations and the formation conditions of these layers help understand the vertical distribution of BC concentrations, which will provide a basis for the assessment of climate effects and early BC pollution warnings. By using the Weather Research and Forecasting with Chemistry (WRF-Chem) numerical model, we performed a numerical simulation analysis on the authenticity of strong elevated BC concentration layers that were detected by an aircraft in the mixing layer over Harbin, China, which is a high-emission area, on a clear sunny afternoon in the early heating period of 2016. We then discuss possible problems and solutions when non-vertical paths are used to detect the vertical distribution of BC concentrations. Finally, we discuss the favorable conditions for the formation of elevated BC concentration layers by weak vertical flow. The results show that the horizontal variability of BC concentration in the mixing layer in the observation area in Harbin was sufficiently large during the measurement. This produced a false elevated layer, as detected by the aircraft during one round of spiral flight in the mixing layer. The root mean square of the horizontal distribution of BC concentration did not change with height in the mixing layer during the daytime, but it decreased with the thickness of the mixing layer and was higher in the mixing layer than in the free atmosphere. Therefore, the thinner the mixing layer, in which the vertical distribution of the BC concentration is detected in an inclined path, the stronger interference of the horizontal variability on the detected results. When a spiral flight detection path is used, the aircraft should fly at least two rounds in the mixing layer. In the daytime, due to strong turbulence in the mixing layer, weak vertical uplift is not favorable for the occurrence of elevated BC concentration layers in the mixing layer. In the nighttime, if weak vertical uplift is well matched with the BC concentration or its vertical gradient, elevated BC concentration layers can be formed in the atmosphere. Compared with upper layers far from the ground, nighttime elevated layers are easier to form in lower layers near the ground because high BC concentrations or large vertical gradients are more likely to occur in the lower layers. Both cases facilitate the occurrence of large vertical upward transport rates of BC.

Polymethyl methacrylate (PMMA) polymer is widely used in various fields today. In order to thoroughly reveal the structural impact performance of PMMA materials, this paper is based on the comprehensive Johnson-Cook constitutive model and damage failure model, and accurately confirm the J-C constitutive and damage failure model parameters of PMMA through material test data, The dynamic process of steel bullet impacting PMMA plate structure is analyzed by finite element software ABAQUS. The calculation results show that the numerical simulation results in this paper are in good agreement with the experimental test data. Therefore, the feasibility and accuracy of the impact analysis of PMMA structures based on J-C constitutive and damage failure models in this paper are studied. Finally, based on the J-C constitutive model and damage failure model, the variation of the residual velocity of the bullet with the PMMA plate thickness is analyzed in depth, that is, the results show that the residual velocity of the bullet has a certain linear relationship with the plate thickness.

Melt mixing is a convenient method to prepare polymer nanocomposites, but the extent of the dispersion of the solid filler reached is often limited, and may compromise the anticipated performance of these materials during service. Since the efficiency of extensional flows on dispersion is now well recognized, several mixers were designed with the aim of inducing both shear and extensional flow components. This work combines experimental and numerical data to better understand the kinetics of the dispersion of graphite nanoplates in a polypropylene melt, using a mixing device that consists of a series of stacked rings with equal outer diameter and alternating larger and smaller inner diameters, thus creating a series of converging/diverging flows. Numerical simulation of the flow using the opensource OpenFOAM software assuming both inelastic and viscoelastic responses predicted the velocity, streamlines, flow type and shear and normal stress fields for the mixer. Experimental and computed data were combined to determine the trade-off between the local degree of dispersion of the PP/GnP nanocomposite, measured as Area ratio, and the absolute average value of the hydrodynamic stresses multiplied by the local cumulative residence time. From considerations based on a theoretical approach to dispersion, the cohesive strength of the GnP agglomerates studied was estimated to be in the range 3 - 10kPa.

Due to the accuracy of numerical calculation of fluid flow inside a hydrocyclone can be obtained using Computational Fluid Dynamics (CFD), highly modified super computers are used to simulate the fluid flow and track particle motion inside a hydrocyclone. This paper deals with the numerical study using three multiphase models viz. Volume of fluid, Mixture and Eulerian model. The dimensions of the hydrocyclone taken into consideration for numerical analysis is same as considered by Rajamani. Validation of axial and tangential velocities at different strategically decided axial stations, RMS axial and tangential velocity profiles of the hydrocyclone is done using Reynolds Stress Model (RSM). The hydrocyclone model has been designed in Creo 3.0 using the same dimensions which later was imported to CFD for meshing. Fine hexagonal mesh numbering up to 5 lacs were constructed to obtain optimum results. Fluid flow was allowed to be developed in ANSYS FLUENT 16.2. Entire simulation took 96 hours to generate results and track particle movements inside the hydrocyclone. The particle tracking has been done using three multiphase model. The first being the volume of fluid was used for validation purposes and the comparison of the Mixture and Eulerian model are the basic focus of this research work. Conclusive results indicate that usage of different multiphase model does not result in variation in particle motion. The slight variation in grade efficiency values are hardly noticeable. The Mixture model and Eulerian model predict lower separation efficiency as compared with Volume of fluid multiphase model.

It is imperative to examine the performance of wind turbines both in steady and unsteady states due to their significant role in generating renewable energy by utilizing wind power. The computational fluid dynamics method (CFD) is one of the most efficient tools in this field, and the unsteady state has a great deal of importance when predicting turbine performance. Using the CFD method, the hydrodynamic performance of two types of offshore and onshore horizontal-axis wind turbines in the unsteady state was examined. Offshore wind turbines were modeled using the SST turbulence model and onshore wind turbines were modeled using the large eddy simulation (LES). Three-dimensional results of the simulation were compared and validated with experimental results, and good agreement between the two results indicates that the assumptions and method were accurate. Vortices were also studied in relation to the blade tip and their formation and development. Increasing the number of blades results in a reduction in torque, as well as a rise in vortices caused by the tips of the rotor blades. Due to the intensity of turbulence, the distribution of pressure on the surfaces will become irregular as the wind speed increases.

Infectious diseases continue to be a significant threat to human health and civilization, and finding effective methods to combat them is crucial. In this research, we investigate the impact of awareness campaigns and optimal control techniques on infectious diseases without proper vaccines. Specifically, we develop an SIRS type mathematical model that incorporates awareness campaigns through media and treatment for disease transmission dynamics and control. The model displays two equilibria, a disease-free equilibrium and an endemic equilibrium, and exhibits Hopf bifurcation when the bifurcation parameter exceeds its critical value, causing a switch in the stability of the system. We also propose an optimal control problem that minimizes the cost of control measures while achieving a desired level of disease control. By applying the minimum principle to the optimal control problem, we obtain analytical and numerical results that show how the infection rate of the disease affects the stability of the system and how awareness campaigns and treatment can maintain system stability. This study highlights the importance of awareness campaigns in controlling infectious diseases and demonstrates the effectiveness of optimal control theory in achieving disease control with minimal cost.