The scope of this study was twofold: first, to introduce a new method in examining measurement invariance, especially with large-scale studies where a large number of group comparisons are involved: the alignment approach, where only configural invariance is necessary to achieve measurement invariance. Second, to evaluate the psychometric robustness of this approach using real-life data. Particularly, we applied this approach to examine whether the factor structure of a cognitive ability test (PGAT) exhibits measurement invariance across the 26 universities of the Kingdom of Saudi Arabia. The sample consisted of 9,849 graduate students from 26 universities around the Kingdom. The results indicated a robust configural model suggesting that the P-GAT subscales were invariant across the 26 universities. Finally, the aligned factor mean values were estimated, and factor mean comparisons of every group’s mean with all other group means were conducted for both cognitive domains (Verbal and Quantitative). In both domains, King Saud University had the highest mean score among all universities. Moreover, its mean factor score was significantly higher than any other university besides Dammam University. On the other hand, several universities allocated at the northern and Southern borders of the country exhibited the lowest factor mean scores.

Environmental pollution by noise is one of the most serious health threats nowadays. The impact of noise on the human body depends not only on the sound level but also on its spectral distribution. Reliable measurements of the environmental noise spectrum are often hampered by the very high price of top quality measuring devices. This paper explores the possibility of using much cheaper audio recorders for frequency analysis. Comparative research were performed in laboratory and field conditions, which showed that, with some limitations, these devices can be useful for the needs of environmental noise frequency analysis. This fact gives an opportunity for reduce the cost of noise analysis experimental work.

This paper deals with a non-contact method to identify the aerodynamic propeller parameters of the Parrot AR.Drone quadrotor. The experimental set consists in a camera recording the vehicle flights, the audio signal is extracted and is used a spectrogram analysis to estimates the propeller velocity. First, the aerial vehicle takes off and starts a hovering maneuver. The experiment is repeated with different additional masses attached to its rigid body. If the weight over the UAV increases/decreases, then the propeller must rotates faster/slower to produce a higher/lower thrust, and consequently, the sound frequency increases/decreases. Finally, this proposition is validated experimentally, and the estimated velocity is used to identify the quadrotor thrust parameters.

To verify the reliability of the proposed stitching linear scan method for roundness measurement of small cylindrical workpieces, measurement uncertainties of the workpieces with various dimension are conducted. The cross-sectional circle of a cylindrical workpiece is divided into several equal arcs to be measured. Thus, the arc profile can be characterized according to the measured arcs. The roundness profile of the cylindrical part can be obtained by stitching these arc profiles together. Firstly, the measurement uncertainty of the workpiece with a diameter 1.5 mm and length 5.8 mm is evaluated to be 0.095 μm which can meet the uncertainty target of 0.1 μm. Considering the uncertainty of θx and θz which are the alignment around X-axis and Z-axis respectively changing with workpiece dimension changing, relevant uncertainties are carried out. As a result, there is no limitation with respect to workpiece diameter theoretically If the alignment can reach θz = θx = ±0.1° without considering the measurable range of the machine.

This paper presents a robust method based on graph topology to find the topologically correct and consistent subset of inter-robot relative pose measurements for multi-robot map fusion. However, the absence of good prior gives a severe challenge to distinguish the inliers and outliers, and wrong loop closures can seriously corrupt the fused global map. Existing works mainly rely on the consistency of spatial dimension to select inter-robot measurements, which does not always hold. In this paper, we propose a fast inter-robot loop closure selection method that integrates the consistency and topology relationship of measurements, which both conform to the continuity characteristics of similar scenes and spatiotemporal consistency. The traditional high-dimensional consistency matrix is decomposed into the sub-matrix blocks corresponding to the overlapping trajectory area. Building on this logic, a clustering method involving topology correctness of inter-robot loop closures is introduced to split the entire measurement set into multiple clusters. We define the weight function to find the maximum cardinality subset with topologically correct and consistent, then convert the weight function to a maximum clique problem in the graph and solve it. We evaluate the performance of our method in a simulation and in a real-world experiment. Compared to state-of-the-art methods, the results show that our method can achieve competitive performance in accuracy while reducing computation time by 75%.

Copper indium gallium diselenide, Cu(In,Ga)Se2, thin-film of about 1.2 μm has been deposited on Mo coated soda lime glass by thermal co-evaporation of Cu, In, Ga, and Se sources. The thin film CIGS was characterized by energy dispersive spectroscopy (EDS) and identified the elemental composition of Cu, In, Ga and Se in the film. A CIGS device was completed by the successive deposition of multiple layers; SLG/Mo/CIGS/CdS/ZnO/ITO which yielded the efficiency of 11%. External spectroscopic ellipsometry (ex-situ SE) was performed on the completed device and the device analysis was performed. Starting with the parameterized complex dielectric functions of the individual component layers, SE analysis was performed using a step-wise procedure that ranks the fitting parameters according to their ability to reduce the mean square error (MSE) of the fit. The resulting layer thicknesses and dielectric functions were used to simulate the external quantum efficiency (EQE) of the device assuming complete active layer collection. Electronic losses were identified by comparison of simulated EQE with the measured EQE. The ultimate goal of this work is the optimization of narrow band-gap CIGS-related solar cells for the bottom layer in tandem devices.

Abstract: The calibrator is one of the most important factors in the calibration of various laser 3D scanning instruments. The requirements for diffuse reflection surface are specially emphasized in many national standards. In this study, the spherical calibrator and plane calibrator compara-tive measurement experiments were carried out. The black ceramic standard sphere, white ce-ramic standard sphere, metal standard sphere, metal standard plane and white ceramic standard plane were used to test the laser 3D scanner. In the spherical calibrators comparative measure-ment experiments, the results indicated that the RMS of the white ceramic spherical calibrator with reflectance about 60% is 10 times that of the metal spherical calibrator with the reflectance of about 15%, and the RMS of the black ceramic spherical calibrator with reflectance of about 11% is of the same order as the metal spherical calibrator. In the plane calibrators comparative measurement experiments, the RMS of flatness measurement is 0.077 mm for metal plane cali-brator with reflectance of 15%, and 2.915 mm for ceramic plane calibrator with reflectance of 60%. The results show that when the optimal measurement distance and incident angle are selected, the reflectance of the calibrator has a great effect on the measurement results, regardless of the outlines or profiles. Based on the experiments, it is recommended to use the spherical calibrator or the standard plane with reflectance of around 18% as the standard, which can obtain the rea-sonable results. In addition, it is necessary to clearly provide the material category and surface reflectance information of the standard when calibrating the scanner according to the measure-ment standard.

The overcrowding of high-rise buildings in the city adversely affects the wind environment by changing the air currents in the surrounding areas. In particular, extreme climate phenomena caused by climate change are stronger and more frequent, causing social damages in cities. To comprehensively better understand the wind properties around high-rise buildings, actual filed measurement is necessary to determine the environment assessment of wind effect. We performed the on-site measurement on LCT residential complex regions (411.6m tall) with highly concentrated high-rise buildings in coastal city Busan, South Korea under extreme weather conditions such as typhoon invasions to determine wind fluid characteristics. In the field monitoring, five anemometers were installed to analyze the wind environment around high-rise buildings when typhoon 'Hinnamnor' invaded. Compared to the nearby weather station operated by KMA(Korea Meteorological Administration), the gust was 3.7 times stronger and the max 1 min-mean wind speed was 3.1 times stronger, and the characteristics of the downward wind and the canyon wind were shown depending on the location characteristics of the point. Turbulence intensity decreased as the wind speed increased and converged to a certain value. Likewise, the gust factor also decreased as the wind speed increased and converged to 2.0, which is considered to be the parameter that best represents the intensity of the instantaneous gust caused by the skyscraper wind effect.

This paper analyzes the measurement error, caused by the position of the current-carrying conductor, of circular array of magnetic sensors for current measurement. The circular array of magnetic sensors is an effective approach for AC or DC non-contact measurement, as its low cost, large linear range, wide bandwidth, light weight and low noise. Especially it has claimed that such structure has the excellent reduction ability for the errors caused by the position of the current-carrying conductor, crosstalk current interference, shape of the conduction cross section and the earth magnetic field. However, the positions of the current-carrying conductor, including un-center and un-perpendicularity, has not analyzed in detail until now. In this paper, the theoretical analysis has been proposed based on vector inner and exterior product. In the presented mathematical model of relative error, the un-center offset distance, the un-perpendicular angle, the radius of the circle and the number of the magnetic sensor are expressed in one equation. The comparison of the relative error caused by the position of the current-carrying conductor between four and eight sensors is conducted. The Tunnel Magnetoresistance (TMR) sensors are used in the experimental prototype to verify the mathematical model. The analysis results can be the reference to design the detail of circular array of magnetic sensors for current measurement in practical situation.

This study aims to explore the possibility of estimating a multitude of kinematic and dynamic quantities using subject-specific musculoskeletal models in real-time. The framework was designed to operate with marker-based and inertial measurement units enabling extensions far beyond dedicated motion capture laboratories. We present the technical details for calculating the kinematics, generalized forces, muscle forces, joint reaction loads, and predicting ground reaction wrenches during walking. Emphasis was given to reduce computational latency while maintaining accuracy as compared to the offline counterpart. Notably, we highlight the influence of adequate filtering and differentiation under noisy conditions and its importance for consequent dynamic calculations. Real-time estimates of the joint moments, muscle forces, and reaction loads closely resemble OpenSim's offline analyses. Model-based estimation of ground reaction wrenches demonstrates that even a small error can negatively affect other estimated quantities. An application of the developed system is demonstrated in the context of rehabilitation and gait retraining. We expect that such a system will find numerous applications in laboratory settings and outdoor conditions with the advent of predicting or sensing environment interactions. Therefore, we hope that this open-source framework will be a significant milestone for solving this grand challenge.

The problem of real-time estimation of occupancy of buildings (number of people in various zones at every time instant) is relevant to a number of emerging applications that achieve high energy efficiency through feedback control. The measurement of CO2 concentration can be considered an important indicator that allows to define the occupation of closed and crowded spaces. Interesting cases can be school buildings and other buildings used in civil and residential (shopping centres, hospitals, etc.). This paper, starting from an experimental analysis in different classrooms of a University campus in real operating conditions, in different period of the year, proposes a possible correlation between CO2 concentration and the occupancy profile of the spaces. The acquired data are used to present some graphical correlations and to understand the most important variables or combination of them. Starting from an accurate analysis of the data, attempts are made to define a preliminary estimation method through the development of a mathematical models of occupancy dynamics in a building, which show interesting results.

International trade has been one of the most significant economic activities among countries, and its contributions towards a country’s economic growth and sustainable development have been acknowledged. In recent times, international trade and global trade networks have received preeminent attention due to the sharp growth in trade volumes and its contributions to poverty reduction and general welfare. Despite the growth in global trade volumes, there are worrying concerns about the unprecedented changes in international trade patterns and growing imbalances in trade in recent times. Whereas China’s trade volumes have more than tripled over the last decades and have maintained the largest trade surplus spot ahead of Germany, other major trade surplus countries such as Japan, the USA, etc. have become trade deficit countries with their trade volumes increasing at a much slower pace. In view of the growing imbalances in global trade volumes, we use an augmented gravity model of trade that incorporates social network measurement, the real effective exchange rate which is a measurement of international competitiveness, as well as the Linder theory of trade, to investigate the factors that determine the export performance of countries. Using data from 51 countries for 41 years, our results indicate that the GDP of both the home country and the partner country affects the home country’s exports positively. Similarly, the real effective exchange rate REER, trade openness OPEN and dummy variables BORDER, ENGLISH, and EU have produced positive and statistically significant coefficient estimates, and these are in line with our theoretical expectations.

One of the most popular techniques for determining electrical properties of material is the free-space measurement technique. With the potential for new applications requiring efficient, accurate and broadband material measurement systems using higher millimeter-wave and terahertz frequencies, the free-space measurement method has received renewed interest. This is mainly due to its simplicity, favorable properties as a non-destructive method, and it allows transmission and reflection measurements without any physical contact with the sample. This paper reviews and discusses state- of-the-art free space material measurement systems, starting with the different measurement techniques available for material characterization, their important concepts, post-processing in determining their properties, and progress towards expanding their use at higher frequencies. Also, this paper reviews dielectric material characterization using the free space method focusing on their application extension towards the higher frequencies. Besides, the algorithms for conversion methods and usage of lens in free space material measurement system was discussed in this paper. Finally, a future perspective on the outlook of this free space method is presented prior to the conclusion.

Surgeries that take place in medicine and dentistry or during any form of childbirth results in a significant amount of blood loss. The prevalent measurement methods that surgeons and anesthesiologists utilize as the “gold - standard” has several drawbacks. There are numerous other methods to measure blood loss, which, however, due to their impracticality and limitations, are not ideal either. This paper focuses on minimally invasive neurosurgery in particular, by taking into account a surgical technique known as Endoscopic Endonasal Transphenoidal surgery (EETS), which is used to treat pituitary tumors and adenomas. Along with the review of the existing literature pertaining to blood loss management, this paper proposes a modified electrode probe method along with the concept of usage, computer interface, and the system of integration. The probe is intended to measure the hematocrit count from the collected blood under all circumstances, such that the medical practitioner is assisted to improve the blood loss management technique for better patient recovery.

This study focuses on the impact of weak partial discharges (PDs) on defect recognition accuracy in epoxy resin through phase-resolved partial discharge (PRPD) analysis. Two measurement conditions are compared until PRPD pattern saturation: one-minute and one-hour durations. The PD data specifically target three void types located at different positions within the epoxy material. The aim is to evaluate how the presence of weak PDs at the PD extinction voltage (PDEV) influences defect recognition accuracy. This research sheds light on the potential implications of neglecting the significance of weak PD signals in defect detection. A convolutional neural network (CNN) model is trained using PRPD data recorded at the PD inception voltage (PDIV) and tested using the new PRPD data from both conditions recorded from a lower PDIV to a PDEV. The trained CNN model achieves a defect recognition accuracy of 100% for a one-hour duration, highlighting the importance of not neglecting weak PD signals. This emphasizes the significance of extended measurement duration and pattern saturation in capturing and analyzing weak PD signals for improved defect recognition. This study contributes to the advancement of practical applications by understanding the behavior of the epoxy material and enhancing defect detection techniques.

This paper introduces a novel approach to addressing the challenge of accurately timing short distance runs, a critical aspect in the assessment of athletic performance. Electronic photoelectric barriers, although recognized for their dependability and accuracy, have remained largely inaccessible to non-professional athletes and smaller sport clubs due to their high costs. A comprehensive review of existing timing systems reveals that claimed accuracies beyond 30 milliseconds lack experimental validation across most available systems.To bridge this gap, a mobile, camera-based timing system is proposed, capitalizing on consumer-grade electronics and smartphones to provide an affordable and easily accessible alternative. By leveraging readily available hardware components, the construction of the proposed system is detailed, ensuring its cost-effectiveness and simplicity. Experiments involving track and field athletes demonstrate the proficiency of the proposed system in accurately timing short distance sprints. Comparative assessments against a professional photoelectric cells timing system reveal a remarkable accuracy of 62 milliseconds, firmly establishing the reliability and effectiveness of the proposed system. This finding places the camera-based approach on par with existing commercial systems, thereby offering non-professional athletes and smaller sport clubs an affordable means to achieve accurate timing.In an effort to foster further research and development, open access to the device's schematics and software is provided. This accessibility encourages collaboration and innovation in the pursuit of enhanced performance assessment tools for athletes.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

This review and meta-analysis (PROSPERO registration number: CRD42020138845) critically evaluates test-retest reliability, concurrent validity and criterion validity of different physical activity (PA) levels of three most-common used international PA questionnaires (PAQs) in national language versions of EU-28: IPAQ-SF, GPAQ, and EHIS-PAQ. In total, 4969 abstracts were read, 287 full-text articles were identified as relvant to the study objectives, and 19 studies were included in the final meta-analysis. The studies’ results and quality were evaluated using the Quality Assessment of Physical Activity Questionnaires (QAPAQ) checklist. Results indicate that only five EU-28 countries validated national language versions of selected PAQs. Meta analysis revealed that assessment of moderate-to-vigourus PA (MVPA) is the most relevant PA level outcome, since no publication bias in any of measurement properties was detected while test-retest reliability was the moderately-high (rw=0.74), and moderate for both criterion (rw=0.41) and concurrent validity (rw=0.72). Reporting of methods and results of the studies was poor with overall moderate risk of bias with total score of 0.43. In conclusion, where only self-reporting is feasible, assessment of MVPA with selected PAQs in EU-28 adult population is recommended for policymaking.

The influence of cuff inflations on nighttime measurements during 24h ambulatory blood pressure (BP) measurements is unknown. We investigated the potential effect of cuff-inflations on asleep parameters using measurements taken simultaneously with a cuffless device using pulse-transit-time (PTT). On the first day of measurement, standard cuff-based 24h BP and cuf-fless measurements were simultaneously performed on right and left arms (CUFF/PTT-D). 1-2 days after the first measurement, the cuffless device was worn alone (PTT-D). Only data from the cuffless device was analyzed. The following mean asleep parameters were analyzed: systolic and diastolic BP, arousals, sleep efficiency, total arousals, arousal per hour and desaturations. 21 in-dividuals were prospectively enrolled. Mean (SD) age was 47(±15) years and 57% were female. Mean systolic asleep BP for the during CUFF/PTT-D and during PTT-D were 131(±21) and 131(±26) mmHg respectively. Mean diastolic asleep BP values during CUFF/PTT-D and during PTT-D were 80(±14) and 84(±14) mmHg respectively (p=0.860, p=0.100 respectively). Systolic and diastolic asleep mean difference was 0.1 (±18.0) and -3.6 (±9.8) mmHg, respectively. There were significantly more total arousals during PTT-D (p=0.042). There was no significant difference seen in sleep efficiency (p=0.339) or desaturations (p=0.896) between the two measurements. We could not show any significant impact from cuff inflations during asleep PTT-D measurements.

Bridge load testing is crucial in evaluating bridge load-carrying capacity and construction quality. However, conventional techniques have many limitations such as the need for direct contact and low acquisition frequency. This study provides a comprehensive examination of the static and dynamic load tests of a multi-span cable-stayed bridge utilizing a ground-based radar inter-ferometer (GB-radar). The case study was conducted at the Fifth Nanjing Yangtze River Bridge (FNYRB), which is recognized as the world's first lightweight steel-concrete composite cable-stayed bridge, with two spans measuring 600 m. To enhance measurement accuracy, a method was proposed to detect and recover radar phase jumps caused by vehicle motion. Furthermore, precise geometry projection was employed to acquire vertical displacements from GB-radar which were taken along the line-of-sight (LOS) direction. Moreover, during the static load test, a continuous deformation was observed with a maximum pace of 0.31 mm/min, indicating a post-construction settlement caused by soft soil consolidation. This case study highlights the high sampling frequency, high measurement accuracy, and exceptional weatherproof ability of GB-radar, thereby demonstrating its potential to be an alternative to the structural health monitoring (SHM) system.

Tipping bucket rain gauges (TBRs) have been, and apparently will continue to be one of the most widely used pieces of equipment for rainfall monitoring, being frequently used for the calibration, validation and downscaling of radar and remote sensing data, due to their major advantages–low cost, simplicity, and low energy consumption. Thus, many works have focused and continue to focus on their main disadvantage–measurement biases (mainly in wind and mechanical underestimations). However, despite arduous scientific effort, calibration methodologies are not frequently implemented by monitoring networks operators or data users, propagating bias in databases and in the different applications of such data, causing uncertainty in the modeling, management, and forecasting in hydrological research, mainly due to a lack of knowledge. Within this context, this work presents a review of the scientific advances in TBR measurement uncertainties, calibration, and error reduction strategies from a hydrological point of view, by describing different rainfall monitoring techniques in Section 2, summarizing TBR measurement uncertainties in Section 3, focusing on calibration, and error reduction strategies in Section 4, a discussion and perspectives in Section 5, and conclusions in Section 6, providing an overview of the of the state of the art and future perspectives of the technology.

A temperature-modulated pyroelectricity measurement system for a small single crystal is developed and applied to standard sample measurements performed on a thin single crystal of lithium niobate. The modulation measurement is based on the AC technique, in which the temperature of the sample is periodically oscillated, and the synchronized pyroelectric signal is extracted using a lock-in amplifier. Temperature modulation is applied by irradiating periodic light on the sample placed in the heat exchange gas. To apply this technique to the transparent reference sample, a commercially available black resin is coated on the sample’s surface to absorb the light energy and transmits it to the specimen. The experimental results are analyzed using a two-layer heat transfer model to verify the effect of the light-absorbing layer as well as the non-contact temperature modulation system.

Electromagnetic eddy current sensors are commonly used to identify and quantify the surface notches of metals. However, the unintentional tilt of eddy current sensors affects results of size profiling, particularly for the depth profiling. In this paper, based on the eddy current thin-skin regime, a revised algorithm has been proposed for the analytical voltage or impedance of a tilted driver–pickup eddy current sensor scanning across a long ideal notch. Considering the resolution of the measurement, the bespoke driver–pickup, also termed as transmitter-receiver (T-R) sensor is designed with a small mean radius of 1 mm. Besides, the T-R sensor is connected to the electromagnetic instrument and controlled by a scanning stage with high spatial travel resolution , with a limit of 0.2 μm and selected as 0.25 mm. Experiments have been out on the voltage imaging of an aluminium sheet with 7 machined long notches of different depths using T-R sensor under different tilt angles. By fitting the measured voltage (both real and imaginary part) with proposed analytical algorithms, the depth profiling of notches is less affected by the tilt angle of sensors. From the results, the depth of notches can be retrieved within a deviation of 10 % for tilt angles up to 60 degrees.

The issue of measurement reliability is certainly undervalued in the local agricultural marketplace organization. Besides, there was nothing identified concerning the extent of cereal commodity trade measurement cost. Hence, this paper aimed to estimate the magnitude of cereals trade quantity measurement cost caused by instrument error and unreliability; mainly by targeting the local marketplace in Ethiopia. The survey was conducted in six different districts’ marketplaces (n = 602) of Oromia region by employing administered structured questionnaires and site mass measurement calibration. The gathered data were analyzed using independent samples t-test, one sample t-test, and analysis of variance. According to the findings, the actual value measurement means of the quantity of most local units of the farmers were greater than small traders. The independent t-test result indicated that the average values of the quantity of the majority of units of measurement between farmers and small traders were varied significantly. Estimated measuring instruments’ error and unreliability associated average measurement cost of one-day market transaction over total cereals marketed amount were higher comparatively for a sack, bowl, and glass units. This study demonstrates that homogeneity in measurement, policy, and institutions that aid cereals trade would have an indispensable role to reduce measurement costs and ensure equitable exchange.

3D measurement is a high-throughput method that can record a large amount of information. In this study, we have developed new methods that could be used for morphological analysis of plants from the information contained in 3D data. Specifically, we investigated characteristics that can be measured by scale (dimension) and/or visual assessment by humans. The characteristics that can be measured on a scale-related dimension were tested based on the bounding box, convex hull, column solid, and voxel. Furthermore, for characteristics that can be evaluated by visual assessment, we propose a new method using normal vectors and local curvature (LC) data. For these examinations, we used our highly accurate all-around 3D plant modelling system. The correlation coefficients between manual measurements and the scale-related methods were all above 0.9. In particular, the differences in LC calculated from the normal vector data allowed us to visualize and quantify the concavity and convexity of leaves. Furthermore, we also found a difference in the time point at which leaf blistering began to develop among the cultivars. The precise 3D model made it possible to perform quantitative measurements of lettuce size and morphological characteristics. In addition, the newly proposed LC-based analysis method made it possible to quantify the characteristics that rely on visual assessment.

A method of accuracy error compensation for the time interval is examined, allowing to eliminate the dependence of accuracy error on the duration of measured intervals and minimising the influence of destabilising factors - ambient temperature changes and the initial deviation of the meter clock generator frequency from the nominal value. The compensation method is based on a calibration procedure that measures precise time intervals under conditions of changing ambient temperature. Then the dependence of the accuracy error on temperature for a particular meter is recorded. Based on these data, a correction table is compiled containing correction factors and temperature values at which these factors were determined. Under real measurement conditions, the correction factor corresponding to the current temperature is determined from the table for measured results correction. The table with correction factor values could be stored in the memory of the meter or processing computer. Experimental verification of the method showed that applying a correction for a meter with a standard XO class clock generator (certificated instability of ±50 ppm) can obtain an equivalent clock generator instability of ±0.15 ppm. The application of the method is efficient in cases where the use of high-end clocking to ensure the required measurement accuracy is not economically feasible.

For the electromagnetic eddy current testing, various methods have been proposed for reducing the lift-off error on the measurement of samples. In this paper, instead of eliminating the measurement error caused by the lift-off effect, an algorithm has been proposed to directly measure the lift-off distance between the sensor and non-magnetic conductive plates. The algorithm is based on a sample-independent inductance (SII) feature. That is, under high working frequencies, the inductance is found sensitive to the lift-off distance and independent of the test piece under an optimal single high working frequency (43.87 kHz). Furthermore, the predicted lift-off distance is used for the thickness prediction of the non-magnetic conductive samples using an iterative method. Considering the eddy current skin depth, the thickness prediction is operated under a single lower frequency (0.20 kHz). As the inductance has different sensitivities to the lift-off and thickness, the prediction error of the sample thickness is different from that of the lift-off distance. From the experiments on three different nonmagnetic samples – aluminium, copper, and brass, the maximum prediction error of the lift-off distance and sample thickness is 1.1 mm and 5.42 % respectively at the lift-off of 12.0 mm.

This study assessed health inequality trends and the degree of maternal healthcare services utilization in the DRC, using two consecutive Demographic and Health Surveys, 2007 and 2013-2014. First, we assessed the changes in the magnitude of inequality in the utilization of MHCS using logistics and regressions. Second, we analyzed the distribution of inequality in each MHCS utilization variable using the Gini coefficient and the Lorenz curve. Third, we used the Wagstaff two groups concentration indices comparison method to assess health inequality trends. Finally, we fitted the concentration curves to estimate the inequality in the utilization of MHCS to the economic condition of women. Women were less likely to have their first ANC visit within the first trimester, less likely to receive checkups during ANC visits, and less likely to attend more ANC visits when living in eastern DRC compared to western DRC. Women in rural areas were less likely to have their last birth by C-section, and less likely to receive PNC than women in urban areas. Women with middle, richer, and richest wealth indexes were more likely to complete more ANC visits, more likely to deliver by C-section, most likely to receive PNC, and more likely to receive ANC than those with lower wealth indexes. Over time, inequality in the utilization of MHCS decreased for ANC and PNC but increased for the delivery by C-sections. These findings suggest that innovative strategies are still needed to improve the utilization of MHC services among poorer, rural, and underserved women in post-conflict DRC.

Objective: To explore the inter-rater reliability of the Measurement Of adherence Via Exercise Demonstration (MOVED) adherence tool. Design: Reliability study of a patient adherence measurement tool.Setting: Simulated physiotherapist-patient consultations. Participants: Sixteen experienced physiotherapists rated patient adherence to exercise. Interventions: N/A Main Outcome Measure: Inter-rater reliability of MOVED.Methods: The MOVED tool consists of two parts. Part one asks patients to self-report their adherence to exercise dose (including number of completed sessions, sets and repetitions in the last seven days). Part two asks patients to demonstrate each exercise. Component scores are totalled to give an overall level of patient adherence to each exercise.Participants were provided with a copy of five physiotherapist-prescribed exercises. Participants were then shown five corresponding video vignettes of simulated physiotherapist-patient consultations where patients were asked to self-report exercise frequency, sets and repetitions and demonstrate each exercise within the context of a consultation. Participants were asked to rate the level of patient adherence to each of the five exercises using the MOVED tool. Inter-rater reliability of MOVED scores was assessed using Intraclass Correlation Coefficient (ICC) and 95% Confidence Intervals. Results: The ICC of part one (self-report) was .90 (95%CI .74-.98), part two (demonstration) was .98 (95%CI .94-.99) and total score was .96 (95%CI .88-.99), demonstrating excellent inter-rater reliability. Conclusion: The MOVED tool, which can highlight whether patients are adhering to exercise technique as well as exercise dose, may provide clinicians and researchers with a more robust measure of exercise adherence when compared with other measures currently available.

In this paper, we analyzed the live fish trajectory recorded from an experiment in an experimental vertical slot fishway. Combined with a numerical simulation, we demonstrated that randomness shown in fish trajectory might not merely be attributed to fish's random choices in its swimming, also could be an adaption consequence to the bulk unsteady turbulent flow structure. Simple superposing the fish trajectory on the time-averaged flow field obtained either by interpolating on discrete point measurements or numerical simulation is not an ideal method for fish movement description in fishway engineering. How to model the fish paths in transient flow and the necessity of simultaneous recording of the flow field and the fish locomotion are challenging topics. The suggested spectrum analysis of the flow field may provide a new general method to reproduce the fish trajectory in a complex turbulent flow.

This study aims to assess using a smartphone app (DecibelX), as a noise measuring alternative to the more costly traditional use of measuring noise levels with a Sound Level Meter (SLM). The study compares the accuracy of the app to readings taken with a SLM and dosimeter, and also evaluates the app’s performance for pure tone and narrow band noise. And a usability study identifies strengths and weaknesses related to usability of the app.

This paper addresses the issues of methodological problems and limitations regarding measuring values. A short scan review of values measurement methods from psychological and ethnobotanical approaches was made to enumerate some of those shortcomings. A new methodological approach, named Kab’s Value Survey (KVS) was proposed and compared with other well adopted methods based on some important criteria to assess its suitability, uniqueness and novelty. The results of the comparisons shows that KVS for its considerations to the theoretical explanations distinguishes itself over other methods of value measurement in the sense that the methodological approach employed is more broad in scope and applications, simple, specific and reliable in terms of instruments for data collection, psychometric data analysis, and of course data presentation. The method however solved some of the criticized limitations that exist in other well adopted methods of values measurement from psychological and ethnobotanical perspectives.

Accurate measurement of low-level thoron gas and high-accuracy calibration of thoron measurement devices are essential for assessing and preventing thoron radiological risks. This study aimed to develop a thoron gas measurement technique using an airflow-through scintillation cell for both low-level measurement and high-accuracy calibration. To achieve this, a compartment model was developed to estimate the influence of progeny deposition and accumulation on the wall of the scintillation cell to prevent overestimation of thoron. A self-developed scintillation cell was utilized to implement and validate this technique. The lower detection limit and measurement uncertainty were then evaluated to assess the feasibility of the technique for low-level measurement and high-accuracy calibration. The results showed that the compartment model effectively addressed the influence of the progeny deposition. The measurement technique achieved a lower detection limit below 100 Bq m-3 even with the coexistence of 100 Bq m-3 of radon and attained a measurement uncertainty (k = 2) below 10% when the concentration of thoron exceeded 1,000 Bq m-3. In summary, this study developed a reliable and practical thoron gas measurement technique using an airflow-through scintillation cell with consideration for progeny deposition, and is expected to contribute to the assessment and prevention of thoron radiological risk.

Vibration measurement serves as the basis for various engineering practices such as natural frequency or resonant frequency estimation. As image acquisition devices become cheaper and faster, vibration measurement and frequency estimation through image sequence analysis continue to receive increasing attention. In the conventional photogrammetry and optical methods of frequency measurement, vibration signals are first extracted before implementing the vibration frequency analysis algorithm. In this work, we demonstrated that frequency prediction can be achieved using a single feed-forward convolutional neural network. The proposed method is verified using a vibration signal generator and excitation system, and the result obtained was compared with that of an industrial contact vibrometer in a real application. Our experimental results demonstrate that the proposed method can achieve acceptable prediction accuracy even in unfavorable field conditions.

Antimony (Sb) Substitution less than 10 % is examined on a single crystal of a layered superconductor NdO_0.7F_0.3BiS₂. Superconducting transition temperature of the substituted samples decreases with increasing Sb concentration. A lattice constant along the c axis showed a large decrease compared with that along the a axis. Since in-plane chemical pressure monotonically decreases with increasing Sb concentration, the suppression of the superconductivity is well described in terms of the decrease in in-plane chemical pressure.

Regular inspections during construction work verify that the work completed is consistent with the plans and specifications and ensure that it is within the planned time and budget. This requires frequent physical site observations to independently measure and verify the completion percentage of the construction progress performed over periods of time. The current computer vision-based (CV) techniques for the measurement of as-built elements, predominantly use 3D laser scanning or 3D Photogrammetry modelling to determine the geometrical properties of as-built elements on construction sites. Both techniques require data acquisition from several positions and angles to generate sufficient information about the element’s coordinates making the deployment of these techniques on dynamic construction project sites a challenging task. In this paper, we propose a pipeline for automating the measurement of as-built components using artificial intelligence (AI) and computer vision (CV) techniques. The pipeline requires a single image obtained with a stereo-camera system to measure the size of selected objects or as-built components. We demonstrate our approach by measuring the size of concrete walls and columns. The novelty of this work is attributed to the fully automated CV-based method for measuring any given element using a single image only. The proposed solution is suitable for use in measuring the sizes of as-built components of built assets. It has the potential to be further developed and integrated with BIM models for use on construction projects for progress monitoring.

MgB2 is a hexagonal superconducting material, and its simple composition has led to the development of low-cost practical wires. However, the problem is that the strain characteristics of filaments are inferior to those of other practical wires, but there have been no strain measurements using diffraction method. The reason for this is presumably that it is a little too thick for synchrotron radiation measurements, and the large absorption cross section of the included boron-10 makes it difficult to obtain elastic scattering for neutron measurements. We prepared a wire substituted with boron-11, an isotope with small neutron absorption cross section, and attempted to measure its strain under tensile loading using pulsed neutron.

The environmental pollution by microplastics (MPs) has become a growing concern, and measures are being taken in many countries. Long-term and extensive MPs investigations involving not only professional researchers but also the citizenry are needed to understand the pollution situation and to confirm the decreasing trend of MPs pollution as a result of pollution control measures. In this study, the author evaluated the accuracy of a simple method of investigating MPs on sandy beaches that can be conducted even by high school students. In a land survey using such simple tools as a tape measure and cardboard, 70% of the deviations were within approximately 20 cm when multiple surveys of approximately 20 m distance were performed. Even without heavy liquid, 89% of MPs could be recovered using only seawater. An investigation of MPs content by sampling 0.5 cm of the surface layer of sand could explain more than half of the MPs content when the sand was sampled to a depth of approximately 50 cm below the surface layer. A method in which the recovered MPs are not visually sorted but floating matter after boiling is considered as MPs is acceptable. If there was no concern about pumice contamination, the overestimation was within approximately 1.5 times. Simple laboratory equipment such as buckets, sieves, seawater, hot plates, dryers, and electronic balances could achieve lower limits of quantification of MPs of 13 mg-MPs/m2-sand and 2 mg-MPs/kg-sand.

Background and Objectives: The Temperament Evaluation of Memphis, Pisa, Paris and San Diego Autoquestionnaire (TEMPS-A) is designed to assess affective temperaments. The short version of TEMPS-A (TEMPS-A-SV) was translated into diverse languages for its broad application in research and clinical settings. However, no study was conducted to validate the Korean version of TEMPS-A-SV among patients with mood disorders. The purpose of this study is to examine the reliability and validity of the TEMPS-A-SV in mood disorder patients of the Korean population. Materials and Methods: In this cross-sectional retrospective study, a total of 715 patients (267 patients with major depressive disorder, 94 patients with bipolar disorder I, and 354 patients with bipolar disorder II) completed the Korean TEMPS-A-SV. Cronbach's alpha and McDonald’s omega was used to assess reliability. Exploratory factor analysis (EFA) was also performed. Spearman's correlation coefficient was used to examine associations between five temperaments. The difference in five temperament scores between gender or diagnosis groups were analyzed, and the correlation between five temperament scores and age were tested. Results: The Korean TEMPS-A-SV displayed good internal consistency (α = 0.65–0.88, ω = 0.66–0.9) and significant correlations between the subscales except one (correlation between hyperthymic and anxious). Using EFA, a two-factor structure was produced: Factor I (cyclothymic, depressive, irritable, and anxious) and Factor II (hyperthymic). The cyclothymic temperament score differed by gender and the anxious temperament score was significantly correlated with age. All the temperaments, except for irritable temperament, showed significant differences between diagnosis groups. Conclusions: Overall, our findings indicate that TEMPS-A-SV is a valid and reliable measure of estimating affective temperaments among Koreans. Our results confirm validity of TEMPS-A-SV among Korean patients with mood disorders. However, more study is required on affective temperaments and associated characteristics in people with mood disorders.

Objectives: Few studies in literature evaluate the "mean measure" of root divergence. Most of them are linear measurements, they hardly describe the dental furcation conformation. It is left to the subjectivity of the operator deciding whether a furcation is convergent or divergent. The goal of this study is to create a visual evaluation method to overcome these problems giving a conformation of the entire interradicular space. Material and methods: A user-friendly software (Paint®, Windows10®) was used to measure endo-oral radiographs of upper and lower molars. Three kinds of measurements were taken. Three operators used the software to measure 20 radiographs, then the technique was repeated on 250 radiographic images to identify an average measurement. The ratio of these three measurements allowed to develop a new visual evaluation method of the interradicular space. Results: Intra and inter-operator reproducibility was statistically assessed on a sample of 20 anonymous endo-oral radiographs measured by 3 blind operators. Then, a sample of 250 anonymous endo-oral radiographs were measured by a blind operator and were statistically evaluated to identify an average value to define a main conformation of the interradicular space. Measurements made by the 3 operators on the 20 radiographic images showed that the technique is reproducible, and a mean value of the interradicular space was obtained. Conclusions: A new anatomical evaluation of the interradicular space in its entirety, which could help the clinicians in the therapy of furcated molars, can be obtained.

Imagination is more important than knowledge, but if intellect does not provide the needed logical structures, capacities for envisioning new possibilities are overly constrained. The sustainability problems we face today cannot be solved with the same kind of thinking that created them, but clarity on what counts as a new kind of thinking is sorely lacking. This article proposes methodical, model-based ways of heeding Bateson's warning about the negative consequences for the ecology of mind that follow from ignoring the contexts of relationships. Informed by S. L. Star's sense of boundary objects, a sequence of increasingly complex logical types distinguishes and interconnects qualitatively different kinds of thinking in ways that liberate imaginative new possibilities for life. The economy of thought instantiated at each level of complexity is only as meaningful, useful, beautiful, ethical, and efficient as the standards informing local adaptive improvisations. Standards mediating the general and specific, global and local, universally transcendent and embodied particulars enable meaningful negotiations, agreements, and communications. Attending to the differences between levels of discourse sets up new possibilities for creative and imaginative entrepreneurial approaches to viable, feasible, and desirable goals for measuring and managing sustainable development.

Nanofibers appearing functional properties show a great promise as allowing constituents for a wide range of medical applications. In this work, Polycaprolactone (PCL), Silver Nitrate (AgNO₃) and Zinc Oxide (ZnO) were used for fabrication of nanofiber composite material by co-axial electrospinning (CAE) process. 5, 10, and 15 wt. % concentrations of PCL were utilized and different amount of AgNO₃ and ZnO were used in entire samples. Morphological analyses of the electrospun nanocomposites were done by scanning electron microscopy (SEM) and AgNO₃, ZnO and PCL materials’ functional groups were determined by Fourier Transform Infrared Spectroscopy (FTIR). Before co-axial electrospinning, physical properties such as liquid state ac conductivity, density and viscosity were measured for all solutions. Capacitance (C_p) and D-factors (tanδ) of nanocomposite materials are measured for the frequency range of 20Hz – 3MHz and the solid state alternating current (ac) conductivity, permittivity (ε’) and dielectric loss (ε’’) were calculated for all solutions after co-axial electrospinning. Effects of concentration percentages of PCL and AgNO₃ on real and imaginary parts of dielectric constant and solid state ac conductivity have been analyzed and comparisons have been made by the results obtained.

1) Background: In service business areas, design enhances the customer experience through the elements which anticipate specific emotional responses of customers. Many service companies are keen to develop and examine design elements from the customer perspective. Furthermore, recently, having considered the significance of customers’ emotional responses by design elements, categorising design elements into manageable dimensions can facilitate the evaluation of design elements. However, design elements and dimensions of design value are not defined in the current service marketing literature, and companies need a measurement tool and managerial guideline to their innovative value creation and compelling service delivery. For these reasons, this research aims to categorise the design value dimensions and propose the managerial implication for the innovative use of design; 2) Methods: This study used the mixed methodology; two stages of interviews and SEM (Structural Equation Modelling); 3) Results: Interview analyses facilitate the identification of design elements in the service delivery process. SEM results underpin the relevance of the categorised design elements and their impact on customer loyalty by comparing different groups (country and time elapsed from experience); and 4) Conclusions: Findings are the fundamentals of developing measuring tool for design and trigger future studies for conceptualising intangible assets.

Background: Exposure to environmental tobacco smoke (ETS) presents substantial health risks for pregnant women and newborn infants. Measurements of ETS include invasive and expensive biochemical tests as well as less invasive and lower-cost self-reported exposure and avoidance measures. Better understanding of self-report measures will help to select ETS assessments for evaluation. Methods: This analysis was conducted within the context of a tailored video intervention to reduce tobacco smoking and ETS exposure during pregnancy and after delivery, in the control group sample of 147 nonsmoking women. Measurements of salivary cotinine concentration, self-reported ETS exposure and avoidance behaviors were captured at 32 weeks gestation and 6 months postpartum. Results: Salivary cotinine concentration was significantly related to ETS avoidance among pregnant nonsmokers at 32 weeks gestation, but not ETS exposure. At 6 months postpartum, both the reported ETS exposure of the infant and maternal avoidance behaviors to reduce her infant’s exposure were associated with the infant’s salivary cotinine concentration. At 32 weeks gestation and 6 months postpartum, avoidance behaviors decreased as exposure increased. Discussion: This study suggests that for nonsmoking women during pregnancy, report of tobacco smoke avoidance is more valid than report of exposure. After delivery, self-reported ETS exposure or avoidance are associated with each other and biochemical measurement of salivary cotinine. These results provide researchers and clinicians with evidence to support inclusion of avoidance behaviors in the selection of ETS measure.

The range of rating instruments in depression measurement and the depth of their analytical relevance constitutes a major development in this psychiatric and psychotherapeutic field of mental health. Though the competition is acute amongst these various instruments, the results for the public have been outstandingly positive. A depression rating scale is essentially a psychiatric measuring instrument utilized in the identification and ranking of depression severity within the patient. The scale provides the practitioner, psychiatrist or psychotherapist, with sufficient information to assess the severity of the depression plotted on the scale. Not used as a “diagnostic tool” itself, nevertheless, the depression rating scale does function as an effective device for designating and assigning a behavioral score which may, then, be used in establishing the severity of depression of value in the designation of a diagnosis and treatment formula. In this paper, we will take a close look at the leading depression rating scales and briefly summarize their scope of assessment value in rating depression.

The integration of spray drying and agglomeration offers significant advantages, such us continuous production with lower energy consumption. However, it is a knife-edge process with a narrow operating window and limited degrees of freedom that decide between successful agglomeration and fluidized bed blockage due to excessive moisture. In this contribution, factors influencing the spray-through agglomeration process of skim milk powder as a model system were investigated via a design of experiments. Three in-line monitoring methods were applied and tested to observe the most important parameters in the agglomeration process: product moisture and particle size distribution. Regarding the moisture content, a capacitive moisture sensor was calibrated with linear regression and a near-infrared sensor with partial least squares regression. Near-infrared spectroscopy was found to be the suitable method for determining moisture content, while the capacitive moisture sensor mainly provides information on the bulk density, the filling level or fluidization state in the fluidized bed. Additionally, particle size distribution data was extracted from the spectral data using in-line data of a spatial filter velocimetry probe in the fluidized bed. This opens the potential to monitor both parameters in real-time with a single non-invasive sensor.

(1) Background: The mediolateral patella displacement is of interest for diagnostics and clinically relevant research questions. Apart from manual testing, no standardized method is currently available. Proper quantification of patella mobility is necessary to understand pathologies at the patellofemoral joint better; (2) Methods: Patella mobility was assessed in 25 healthy individuals using a Patellostabilometer, a new prototype instrument for quantification of the mediolateral patella displacement. The participants underwent measurements of the mediolateral displacement three times using the Patellostabilometer. A maximal force of 10N was applied for patella movement. Additionally, leg length, circumference of the knee, upper- and lower leg was measured. (3) Results: Lateral patella displacement of 18.27±3.76 mm (range 15.85-20.64mm, interquartile range (IQR) of 4.79) was measured. The medial patella displacement showed 24.47±6.59mm (range 19.29-29.76mm, IQR of 10.47). The test-retest measurement error was 2.32±1.76mm (IQR of 2.38mm), with five outliers. There was greater test-retest variability between the measurements of the medial displacement comparing to the lateral one (4) Conclusions: The test-retest variability reached 7% of the patella displacement. Other parameters provided no significant correlations. Based on the natural patellofemoral mobility a precise and clinically relevant quantification of patella mobility is allowed.

In this research the possibility of using pH change to measure proton conductivity of proton exchange membranes (PEM) or else known as polymer electrolyte membranes are tested with using an experimental setup prepared by using pH meters. PEMs are an important part of the fuel cells and proton conductivity of the PEMs are one of the most important properties of the PEMs. Also, proton conductivity is the one of the biggest limiting factors of fuel cells thus it is important to measure the proton conductivity of the PEMs while trying new polymers or new types of membranes. But as current measurement methods do not have a standard and can be separated into mainly two different measurement methods which are Electron Impedance Spectroscopy (EIS) and Ion Exchange Capacity (IEC). EIS gives clearer results, but it needs an impedance analyzer machine, platinum electrodes and setup so this cannot be possible for every researcher due to its economical aspect. For IEC it is basically a titration method to see acid groups in the polymer or polymer matrix which are directly responsible for proton conductivity so this can show an indirect measurement of proton conductivity. But as for this one drawback are firstly this one is an indirect measurement and secondly needs overnight bath in solution can take long times. So, the possibility of using pH can be easier and both from time and economical aspect if it can be proven the give a direct relationship between pH change and proton conductivity.

This paper aims at trying to answer the question of whether a low cost drone equipped with a regular camera can serve as a simple device to estimate the size of objects. Ad-ditionally, it assesses if the accuracy of measurement is good enough for using a drone for measurements, relying solely on GPS position and camera. A review of the literature pertaining to ground object measurements was conducted. The availability of such in-struments was evaluated in terms of purchase and rental costs, the number of instru-ments on the market, and the time to obtain them. The most common measurement methods were considered and their unit costs were reviewed. The cost of professional surveying and measuring equipment was compared to the possibility of using low-cost, non-commercial drones to measure objects and surfaces. The quality of the images ob-tained was compared with high-resolution satellite systems. Is an ordinary drone with a standard camera suitable for length measurement without professional measuring equipment? Should the results be considered only in the category of size estimation?

Lift-offs of the sensor could significantly affect the measurement signal and reconstruction of material properties when using the electromagnetic (inductive) eddy current sensor. Previously, various methods (including novel sensor designs, and features like zero-crossing frequency, lift-off point of intercept) have been used for eliminating the measurement error caused by the lift-off distance effect of the sensor. However, these approaches can only be applied for a small range of lift-off variations. In this paper, a linear relationship has been found between the sensor lift-off and ratio of dual-frequency eddy current signals, particularly under the high working dual frequencies. Based on this linear relationship, the lift-off variation can be reconstructed firstly with a small error of 2.5 % when its actual value is up to 10 mm (10.1 % for 20 mm). The reconstructed lift-off is used to further get the property of the material under a low single frequency. Experiments on different ferrous metals have been carried out for the testing of the reconstruction scheme. Since the inductance is more sensitive to the material property (and less sensitive to the lift-off) under low frequencies, the reconstruction error of the material property is much smaller than that of the lift-off, with 1.4 % under 12 mm (and 4.5 % under 20 mm).

The direct measurements of the magnetic flux density in steel blocks within Compact Muon Solenoid (CMS) magnet yoke are performed with 22 flux loops installed in selected regions of the yoke. The 10,000-ton CMS magnet flux return yoke encloses a 4 T superconducting solenoid with a 6-m-diameter by 12.5-m-length free bore and consists of five dodecagonal three-layered barrel wheels and four end-cap disks at each end. The yoke steel blocks, mostly up to 620 mm thick, serve as the absorber plates of the muon detection system. A TOSCA 3-D model of the CMS magnet has been developed to describe the magnetic field everywhere outside of the tracking volume which was measured with a field-mapping machine. In the present study, for the first time, the reliable reconstruction of the magnetic flux density in the steel blocks of the yoke is performed using the CMS magnet standard discharges from the operational magnet current of 18.164 kA. To provide this reconstruction, the voltages induced in the flux loops (with amplitudes of 20–250 mV) have been measured with six 16-bit DAQ modules and integrated offline over time. The results of the flux loop measurements during three magnet ramp downs are presented and discussed.

The accurate assessment of wound size is a critical step in advanced wound care management. This study aims to introduce and validate a Light Detection and Ranging (LiDAR) technique for measuring wound size. Twenty-eight wounds treated from December 2022 to April 2023 at the Chunganam National University Hospital were analyzed. All wounds were measured using three techniques; conventional ruler methods, the LiDAR technique, and ImageJ analysis. Correlation analysis, linear regression, and Bland-Altman plot analysis were conducted to validate the accuracy of the newly introduced method. The measurement results (Mean ± Standard deviation) obtained using the Ruler method, LiDAR technique, and ImageJ analysis were 112.99 ± 110.07 cm², 73.59 ± 72.97 cm², and 74.29 ± 72.15 cm², respectively. The Pearson correlation coefficient was higher in the LiDAR application (0.995) than the conventional ruler methods (Mean difference; -5.0000 cm2), as was the degree of agreement (Mean difference; 38.6933 cm2). Wound size measurement using LiDAR is a simple and reliable method that allows practitioners to conveniently assess wounds with a flattened and irregular shape. However, non-flattened wounds cannot be assessed owing to the technical limitations of LiDAR.

This review paper provides a comprehensive overview of machine vision pose measurement algorithms. The paper focuses on the state-of-the-art algorithms and their applications. The paper is structured as follows: The introduction in Section 1 provides a brief overview of the field of machine vision pose measurement. Section 2 describes the commonly used algorithms for machine vision pose measurement. Section 3 discusses the factors that affect the accuracy and reliability of machine vision pose measurement algorithms. Section 4 presents the applications of machine vision pose measurement in various fields. The paper provides specific examples of how machine vision pose measurement is used in each of these fields. Finally, Section 5 summarizes the paper and provides future research directions. The paper highlights the need for more robust and accurate algorithms that can handle varying lighting conditions and occlusion. It also suggests that the integration of machine learning techniques may improve the performance of machine vision pose measurement algorithms. Overall, this review paper provides a comprehensive overview of machine vision pose measurement algorithms, their applications, and the factors that affect their accuracy and reliability. It provides a valuable resource for researchers and practitioners working in the field of computer vision.

This paper deals with the possibility for construction of the database on friction coefficient on the actual roads from the viewpoint of traffic safety. A measurement algorithm is determined in order to construct road friction measuring device. Next, the tires used for measurement are selected and the characteristics are measured using bench tire characteristic tester, and the measuring device is designed and constructed based on the characteristics. Finally, using this device, the measurement results of the road friction characteristics for two types of road surfaces are shown.

Quantitative dynamic strain measurements of the ground would be useful for engineering scale problems such as monitoring for natural hazards, soil-structure interaction studies and non-invasive site investigation using full waveform inversion (FWI). Distributed Acoustic Sensing (DAS), a promising technology for these purposes, needs to be better understood in terms of its directional sensitivity, spatial position, and amplitude for application to engineering-scale problems. This study investigates whether the physical measurements made using DAS are consistent with the theoretical reception patterns and experimental measurements of ground strain made by geophones. Results show that DAS and geophone measurements are consistent in both phase and amplitude for broadband (10s of Hz), high amplitude (10s of microstrain) and complex wavefields originating from different positions around the array when: (1) the DAS channels and geophone locations are properly aligned, (2) the DAS cable provides good deformation coupling to the internal optical fiber, (3) the cable is coupled to the ground through direct burial and compaction, and (4) laser phase noise is mitigated in the DAS measurements. The theoretical relationship between DAS-measured and point-wise strain for vertical and horizontal active sources is introduced using 3D elastic finite-difference simulations. The implications of using DAS strain measurements are discussed including directionality and magnitude differences between the actual and DAS-measured strain fields. A method for spatially aligning the DAS channels with the geophone locations at tolerances less than the spatial resolution of the DAS system is proposed.

This research deals with the possibility for construction of the database on the braking friction coefficient for actual roads from the viewpoint of traffic safety especially for automated driving such as level 4 or higher. In an automated driving such levels, the controller needs to control the vehicle, but the road surface condition, especially the road friction coefficient on wet roads, snowy or icy roads, changes greatly, and in some cases, changes by almost one order. Therefore, it is necessary for the controller to constantly collect environment information such as the road friction coefficients and prepare for emergencies such as obstacle avoidance. However, at present, the measurement of the road friction coefficients is not systemically performed, and a method for accurately measuring has not been established. In order to improve this situation, this study examines a method for continuously measurement for the road friction characteristics such as μ-s characteristics.

The unexploited unification of general relativity and quantum mechanics (QM) prevents the proper understanding of the micro- and macroscopic world. Here we put forward a mathematical approach that introduces the problem in terms of negative curvature manifolds. We suggest that the oscillatory dynamics described by wave functions might take place on hyperbolic continuous manifolds, standing for the counterpart of QM’s Hilbert spaces. We describe how the tenets of QM, such as the observable A, the autostates ψa and the Schrodinger equation for the temporal evolution of states, might work very well on a Poincaré disk equipped with rotational groups. This curvature-based approach to QM, combined with the noncommutativity formulated in the language of gyrovectors, leads to a mathematical framework that might be useful in the investigation of relativity/QM relationships. Furthermore, we introduce a topological theorem, termed the punctured balloon theorem (PBT), which states that an orientable genus-1 surface cannot encompass disjoint points. PBT suggests that hyperbolic QM manifolds must be of genus ≥ 1 before measuring and genus zero after measuring. We discuss the implications of PBT in gauge theories and in the physics of the black holes.

The existence of the hole on a plate affects the calculation of eddy current problems. Consequently, the accuracy for the prediction of the material properties decreases if the effect of the hole is not taken into account. In this paper, a novel analytical method based on the modified integration range is proposed which can address the presence of the hole. Due to the presence of the hole, the conventional Dodd-Deeds analytical solution cannot be used to calculate the inductance change. Therefore, a revised upper integration limit is introduced to replace the original limit -- ∞ when using the co-axially air-core electromagnetic sensor. With the presence of the hole, the magnitude of the received signal reduces, and the peak frequency feature changes. The analytical method is validated by measured and numerical simulation results. It is found that the upper limit is related to the radius of the open hole. With the new technique, the thickness of sample plates with holes can be estimated based on the peak frequency feature.

This article analyzes in detail the influence of Jupiter on the measurement of the gravitational constant. Including a specific estimate of the change in the gravitational constant caused by the change of the earth's orbital position every half month. The influence of Jupiter's perihelion and aphelion on the gravitational constant is also estimated. On this basis, this article analyzes the data with specific time records such as BIPM-01, BIPM-14, JILA-10, UCI-14, HUST-09. The analysis results show that after considering the influence of Jupiter, the experimental results have been significantly improved.

Durability and performance of electrochemical energy converters such as fuel cells and electrolysers are not only dependent on the properties and the quality of the used materials. They strongly depend on operation conditions. Variations in external parameters, such as flow, pressure, temperature and, obviously, load can lead to significant local changes of current density, even local transients. The segmented cell technology was developed with the purpose to gain insight into local operation conditions in electrochemical cells, during operation. The operando measurement of the local current density and temperature distribution allows effective improvement of operation conditions, mitigation of potentially critical events and assessment of the performance of new materials. The segmented cell, which can replace a regular bipolar plate in the current state of the technology, can be used as monitoring tool and for targeted developments. This article gives an overview over the development and applications for proton exchange membrane fuel cell of this technology, such as water management or fault recognition. Recent advancements towards locally resolved monitoring of humidity and to current distributions in electrolysers are outlined.

Recent advances in the theory of quantum gravity show that the Ricci flow serves as the time evolution operator for the vacuum energy density and that in the presence of baryonic matter, the Ricci flow is analogous to the heat equation in the presence of a heat sink. Here we show using the equations of quantum gravity, that quantum information can be modelled as a thermal fluid consisting of a superposition of weakly excited eigenstates of a quantum field and that each eigenstate vector has an associated eigenstate potential well. The depth of the potential well depends on the amplitude of the eigenstate vector. Measurement is then considered as a selection by tuning process which only allows an eigenstate resonating with the detector to be detected. During the detection process, the resonating eigenstate vector increases in amplitude, deepening its potential well such that the other weakly excited states rapidly drain their small excitation energies into it via the principle of minimum action. This draining process is the act of collapsing the wave function to a specific state. Also, the presence of the eigenstate potential wells is what cancels out the infinities from high energy interactions.

Background: We considered a problem of inference in epidemiology when cumulative exposure is the true dose metric for disease, but investigators are only able to measure its duration on each subject. Methods: We undertook theoretical analysis of the problem in the context of a continuous response caused by cumulative exposure, when duration and intensity of exposure follow log-normal distributions, such that analysis by linear regression is natural. We present a Bayesian method to adjust duration-only analysis to incorporate partial knowledge about the relationship between duration and intensity of exposure and illustrate this method in the context of association of smoking and lung function. Results: We derive equations that (a) describe under what circumstances bias arises when duration of exposure is used as a proxy of cumulative exposure, (b) quantify the degree of such bias and loss of precision, and (c) describe how knowledge about relationship of duration and intensity of exposure can be used to recover an estimate of the effect of cumulative exposure when only duration was observed on every subject. Conclusions: Under our assumptions, when duration and intensity of exposure are either independent or positively correlated, we can be more confident in qualitatively interpreting the direction of effects that arise from use of duration of exposure per se. To make reliable inference about the magnitude of effect of cumulative exposure on the outcome, we can use external information on the relationship between duration and intensity of exposure even if intensity of exposure is not available at the individual level.

Tuberculosis (TB) associated stigma is well-documented phenomenon that may contribute to sub-optimal TB care in Pakistan. The objective of study was to assess TB related knowledge and perceived stigma among community members. This was cross-sectional survey using convenience sample of 183 individuals recruited between October and December 2017. A validated stigma measurement tool developed by Van Rie et al. was adapted. Data was analyzed using SPSS version 20.0. 183 individuals (73% males; n = 134) participated in survey. Eighty-seven percent were aware that TB is curable disease (n = 159) and 91% thought that it could be transmitted by coughing (n = 167). However, respondents also thought that TB was spread through contaminated food (73%; n = 134), sharing meals (55%; n = 100), sharing utensils (53%; n = 96) and by having sexual intercourse with a TB patient (51%; n = 93). Fifty-seven percent (n = 104) associated TB with high levels of stigma. Persons who had less than six years of education (crude OR = 1.2; 95% CI: 0.89, 1.72) and lacked knowledge that TB is curable (crude OR = 3.42; 95% CI: 1.20, 9.70) were more likely to associate TB with stigma. In addition, females (crude OR = 1.33; 95% CI: 0.87, 2.04) and those who were unemployed (crude OR = 1.06; 95% CI: 0.65, 1.74) were also more likely to associate TB with stigma. We found an association between lack of knowledge about TB and perceived stigma. This highlights need for improved education and awareness about TB.

Prolonged sedentary behaviour (SB) has shown to be detrimental to health. Nevertheless, population levels of SB are high and interventions to decrease SB are needed. This study aimed to explore the effect of an individualized consultation intervention aimed at reducing SB and increasing breaks in SB among college employees. A pre-experimental study design was used. Participants (n=36) were recruited at a college in Massachusetts, USA. SB was measured over 7 consecutive days using an activPAL3 accelerometer. Following baseline measures, all participants received an individualized SB consultation which focused on limiting bouts of SB >30 minutes, participants also received weekly follow-up e-mails. Post-intervention measures were taken after 16 weeks. Primary outcome variables were sedentary minutes/day and SB bouts >30 minutes. Differences between baseline and follow-up were analyzed using paired t-tests. The intervention did not change daily sedentary time (-0.48%; p>0.05). The number of sedentary bouts >30 minutes decreased significantly by 0.52 bouts/day (p=0.015). In this study a consultation based SB intervention was successful in reducing number of bouts >30 minutes of SB. However, daily sedentary time did not reduce significantly. These results indicate that consultation-based interventions may be effective if focused on a specific component of SB.

Mathematical models of cognition measure individual differences in cognitive processes, such as processing speed, working memory capacity, and executive functions, that may underlie general intelligence. As such, cognitive models allow identifying associations between specific cognitive processes and tracking the effect of experimental interventions aimed at the enhancement of intelligence on mediating process parameters. Moreover, cognitive models provide an explicit theoretical formalization of theories regarding specific cognitive process that may help overcoming ambiguities in the interpretation of fuzzy verbal theories. In this paper, we give an overview of the advantages of cognitive modeling in intelligence research and present models in the domains of processing speed, working memory, and selective attention that may be of particular interest for intelligence research. Moreover, we provide guidelines for the application of cognitive models in intelligence research, including data collection, the evaluation of model fit, and statistical analyses.

The commercial equipment that carries out the measurement of temperature has a high cost. Therefore, this article describes the development of a temperature measurement equipment, which uses a microcontrolled platform, responsible for managing the data of the collected temperature signals and making available the acquired information, so that they can be verified in real time at the measurement site, or remotely. The construction of the temperature measurement equipment was performed using open platform hardware / software, where performance tests were carried out with the objective of developing a temperature measurement equipment that has measurement quality and low cost.

In the past 50 years, calorimeters have become the most important detectors in many particle physics experiments, especially experiments in colliding-beam accelerators at the energy frontier. In this paper, we describe and discuss a number of common misconceptions about these detectors, as well as the consequences of these misconceptions. We hope that it may serve as a useful source of information for young colleagues who want to familiarize themselves with these tricky instruments.

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

A method of measuring the absolute pose parameters of a moving rigid body using a monocular camera is proposed, aiming at addressing calibration difficulties and inconsistencies of repeated measurements of the rigid-body pose for a camera having a varying focal length. The proposed method does not require calibration beforehand. Using more than six non-coplanar control points symmetrically arranged in the rigid-body and world coordinate systems, the matrices of rotation and translation between the camera and two coordinate systems are obtained and the absolute pose of the rigid body measured. In this paper, formulas of the absolute pose measurement of a moving rigid body are deduced systematically and the complete implementation is presented. Position and attitude measurement experiments carried out on a three-axis precision turntable show that the average absolute error in the attitude angle of a moving rigid body measured by an uncalibrated camera at different positions changes by no more than 0.2 degrees. Analysis of the three-dimensional coordinate errors of the centroid of a moving rigid body shows little deviation in measurements made at three camera positions, with the maximum deviation of the average absolute error being 0.53 cm and the maximum deviation of the standard deviation being 0.66 cm. The proposed method can measure the absolute pose of a rigid body and is insensitive to the position of the camera in the measurement process. This work thus provides guidance for the repeated measurement of the absolute pose of a moving rigid body using a monocular camera.

Particulate matter (PM) represents an air quality management challenge for confined swine production systems. Because of the limited space and ventilation rate, PM can reach relatively high concentrations in swine barns. PM in swine barns possesses different physical, chemical, and biological characteristics than that in the atmosphere and other indoor environments. As a result, it exerts different environmental and health effects and creates some unique challenges regarding PM measurement and mitigation. Numerous research efforts have been made, generating massive data and information. However, relevant review reports are sporadic. This study aims to provide an updated comprehensive review of swine barn PM, focusing on publications since 1990. It covers various topics, including PM characteristics, sources, measurement methods, and in-barn mitigation technologies. Since PM in swine barns is of primarily biological origins, bioaerosols are reviewed in great detail. Relevant topics include bacterial/fungal counts, viruses, microbial community composition, antibiotic-resistant bacteria, antibiotic resistance genes, endotoxins, and (1→3)-β-D-glucans. For each topic, existing knowledge is summarized and discussed and knowledge gaps are identified. Overall, PM in swine barns is complicated in chemical and biological composition and highly variable in mass concentrations, size, and microbial abundance. Feed, feces, and skins constitute the major PM sources. Regarding in-barn PM mitigation, four technologies (oil/water sprinkling, ionization, alternation of feed and feeders, and recirculating air filtration) are dominant. However, none of them have been widely used in commercial barns. A collective discussion of major knowledge gaps and future research needs is offered at the end of the report.

All the arguments of a wavefunction are defined at the same instant implying a notion of simultaneity. In a somewhat related matter, certain phenomena in quantum mechanics seem to have non-local causal relations. Both concepts are in contradiction with special relativity. We propose to define the wavefunction with respect to the invariant proper time of special relativity instead of standard time. Moreover, we shall adopt the original idea of Schrodinger suggesting that the wavefunction represents an ontological cloud-like object that we shall call ‘individual fabric’ that has a finite density amplitude vanishing at infinity. Consequently, measurement can be assimilated to a confining potential that triggers an inherent non-local mechanism within the individual fabric. It is formalised by multiplying the wavefunction with a localising gaussian as in the GRW theory but in a deterministic manner.

Gait analysis has historically been implemented in laboratory settings with expensive instruments; however, recently, wearable sensors have allowed the integration into clinical applications and use in daily activities. Previous studies have shown poor validity of ankle joints using inertial measurement units (IMUs), especially for small movement ranges. The purpose of this study was to validate the ability of commercially available IMUs to accurately measure the ankle joint angles during running. Ten healthy subjects participated in the study. Validation was performed by comparing the ankle joint angles measured using the wearable device with those obtained using the gold standard motion capture system during running. Reliability was evaluated using the intraclass correlation coefficient and standard error of measurement, whereas validity was evaluated using Pearson coefficient correlation method. Day-to-day reliability was excellent in the two planes for ankle joints. Validity was good in both sagittal and frontal planes for ankle joints. The results suggested that the developed device might be used as an alternative tool to the 3D motion capture system.

In the concept of the process signature, the relationship between a material load and the modification remaining in the workpiece is used to better understand and optimize manufacturing processes. The basic prerequisite for this is to be able to measure the loads occurring during the machining process in the form of mechanical deformations. Speckle photography is suitable for this in-process measurement task and is already used in a variety of ways for in-plane deformation measurements. The shortcoming of this fast and robust measurement technique based on image correlation techniques is that out-of-plane deformations in the direction of the measurement system cannot be detected and increases the measurement error of in-plane deformations. In this paper, we investigate a method that infers local out-of-plane motions of the workpiece surface from the decorrelation of speckle patterns and is thus able to reconstruct three-dimensional deformation fields. The implementation of the evaluation method enables a fast reconstruction of 3D deformation fields, so that the in-process capability remains given. First measurements in a deep rolling process show that dynamic deformations underneath the die can be captured and demonstrate the suitability of the speckle method for manufacturing process analysis.

In the present work, doped ZnO (ZnO:Al) thin film has been grown on Silicon (Si) substrate by DC sputtering. The obtained thickness of the film is 230 ± 5 nm. The films were subjected to swift heavy ion (SHI) irradiation 120 MeV, Ag⁹⁺ with different fluences ranging from 3 × 10¹¹ to 3 × 10¹³ ions/cm². To study the impact of SHI, both pristine and irradiated samples were characterized to obtain the structural, surface morphological and electrical properties using X-ray diffractometry (XRD), atomic force microscopy (AFM) and hall effect measurement system respectively. From XRD results it is observed that there is change in crystallinity of the film with increase in irradiation fluence. The surface morphological studies through AFM shows the increase in surface roughness with increase in fluence. A significant change is also observed in electrical parameters viz conductivity, mobility and carrier concentration. Conductivity, mobility and carrier concentration decreases with increasing fluence.

A variant of the von Neumann-Wigner Interpretation is proposed. It does not make use of the familiar language of wave functionsand observers. Instead it pictures the state of the physical world as a vector in a Fock space and, therefore not, literally, a functionof any spacetime coordinates. And, rather than segregating consciousness into individual points of view (each carrying with it asense of its proper time), this model proposes only unitary states of consciousness, Q(t), where t represents a fiducial time withrespect to which both the state of the physical world and the state of consciousness evolve. States in our world's Fock space areclassified as either 'admissible' (meaning they correspond to definite states of consciousness) or 'inadmissible' (meaning they donot). The evolution of the state vector of the world is such as to always keep it restricted to 'admissible' states. Consciousness istreated very much like what Chalmers calls an "M-Property." But we try to show that problems with the quantum Zeno effect do not arise from this model.

Optical micro-angiography (OMAG) is a new method of detecting flow rate and widely used for in vivo imaging. Although OMAG can distinguish between flowing and stationary parts, it cannot obtain accurate flow rate information. This study proposed a range formula for OMAG and the ultrahigh-sensitivity OMAG (UHS-OMAG) method to quantify the measurement range of an entire system. The parameters of the angle between beam scanning and flow directions, the angular velocity of the galvanometer, and the offset of incident light were introduced, and a formula for calculating the range was derived. Experiments were conducted to measure fine and ultra-fine flow rates by using OMAG and UHS-OMAG methods. The minimum measured flow rate was approximately 30 μm/s, and the maximum measured flow rate was approximately 8 mm/s. Experimental results are in good agreement with the preset results.

We address Multi-Wall Carbon NanoTubes (MWCNTs) for structural health monitoring in adhesive bonds such as in building structures. MWCNT-loaded composites are employed to sense strain changes under tension load using an AC impedance measurement setup. Different weight percentages of 1, 1.5, 2 and 3 wt.% MWCNT are added to the base epoxy resin using different dispersion times, i.e. 5, 10 and 15 minutes. The equivalent parallel resistance of the specimens is measured by applying an alternating voltage at different frequencies. To determine the mechanical as well as sensory properties, the specimens are subjected to a tensile test with concurrent impedance measurement. Using alternating voltage, a higher sensitivity of the impedance reading can be achieved. Employing these sensors in buildings and combining the readings of a network of such devices can significantly improve the buildings’ safety. Additionally, networks of such sensors can be used to identify necessary maintenance actions and locations.

A method for measuring the real part of the weak value of spin for non-zero rest mass atoms is presented using a variant on the original Stern-Gerlach apparatus. The experiment utilises helium in the metastable 2³S₁ state. A full simulation for observing the real part of the weak value using the impulsive approximation has been carried out and it predicts a displacement of the beam, Δ_w, that is within the resolution of our detector. It also indicates how this shift might be increased. The full analysis also indicated that there is a limit, L, to the applicability of the weak value approximation and has been evaluated for our apparatus. This experiment has the possibility to be expanded to utilise other nobal gas species such as neon and argon in the ³P₂ metastable state, but we shall restrict this paper to metastable helium only.

This paper presents a two-dimensional mathematical model of compound eye vision. Such a model is useful for solving navigation issues for autonomous mobile robots on the ground plane. The model is inspired by the insect compound eye that consists of ommatidia, which are tiny independent photoreception units, each of which combines a cornea, lens, and rhabdom. The model describes the planar binocular compound eye vision, focusing on measuring distance and azimuth to a circular feature with an arbitrary size. The model provides a necessary and sufficient condition for the visibility of a circular feature by each ommatidium. On this basis, an algorithm is built for generating a training data set to create two deep neural networks (DNN): the first detects the distance, and the second detects the azimuth to a circular feature. The hyperparameter tuning and the configurations of both networks are described. Experimental results showed that the proposed method could effectively and accurately detect the distance and azimuth to objects.

To handle the problem of solving the results of aircraft’s visual navigation with scene matching, this paper take the measure of the spherical EPnP positioning posture solving by measuring the central angle threshold value and approaches for constructing a measuring model. The detailed steps are as follows: firstly, this approach needs to construct a positioning coordinate model for the earth surface, makes sure the expression for the 3-dimensional coordinate of the earth surface and solves the positioning of constructing data model with EPnP positioning posture solving algo-rithm. Secondly, by contrasting and analyzing the positioning posture value of approximate plane coordinates, the critical value is acquired, which can be recognized as plane calculation. Lastly, this method should construct a theoretical model of measurement for the visual height and central angle with the decided central angle threshold value. The simulation experiment shows that the average positioning precision of taking the spherical coordinates as input is 16.42 percent way higher than taking the plane coordinates as input. When the central angle is less than 0.05 degrees and the surface district is less than 5585 square meters, the positioning precision of the plane co-ordinates is pretty much equal to the spherical coordinates. At this moment, the sphere can be seen as flat. The conclusion of this essay can theoretically guide the further study of positioning posture solving of the scene matching, which is also of vital significance for theory research and engineering application.

In the present study, a numerical model was developed to predict the flow pattern inside a broiler building. The model intends to predict the velocities fields inside the domain and ammonia (NH3) emitted or released by litter from poultry housing. The numerical model developed in Computational Fluid Dynamics (CFD) commercial code, intends to represent a commercial broiler building, and intends to simulate the 3D and heat transfer, in steady state flow. The evaporative cooling pads were also included in the model. The validation of the model was based in experimental measurements obtained in previous studies. The simulations were focused on Summer, Winter and also Mid-Season situation. The numerical results of NH3 concentration were compared with the experimental measurements, and a quite good agreement was verified. The numerical results allowed the characterization of: the inside flow pattern developed for the summer and winter situation; the inside NH3 distribution, and the velocity field distribution inside the broiler building. It was found that NH3 concentration increases along the tunnel, especially in low flow rate imposed from the exhaust fan. Also, it was verified that the low velocities inside domain are no sufficient to remove the gaseous pollutants.

The minimum requirement for uncertainty estimation is to use only intermediate precision (R_w), especially for measurands lacking a reference measurement system such as thyroid functions tests (TFT). In this study, measurement uncertainty (MU) for TSH and FT4 from long-term internal quality control (IQC) data was estimated while reference change values (RCV) were calculated from estimated MU. Furthermore, intermediate precision (R_w) was used to establish appropriate risk-based QC frequency. Twenty fore months of third party IQC data were collected retrospectively, on the Abbott ARCHITECT i1000sr analyzer from INSTITUT PASTEUR OF MSILA laboratory, ALGERIA. The MU, RCV and sigma-metric were estimated simply from the intermediate precision (R_w), while a nomogram relating sigma performance to run size was used to establish QC frequency. The MU for the TSH and FT4 was 12% and 8% respectively. The U _one-sided for the TSH and FT4 was 10%, 6.6% respectively. MU and U _one-sided of TSH and FT4 met quality requirements for permissible uncertainty (pU %) and allowable total error (ATE %). When monitoring thyroid replacement therapy, an upward minimum change (RCV) of 54% and 22% or a downward of 35% and 18% in serum TSH and FT4 respectively, would be considered significant. Optimal QC strategy for serum TSH was selected to run 4 QC materials every 190 patients sample and to use a multi-rule (1_3s/2_2s/R_4s/4_1s). Our results suggest that MU estimation from long-term IQC alone may be acceptable for TFT to assist physician in results interpretation and to establish appropriate QC frequency.

Purpose: We hypothesized that a recently introduced epibulbar micro-shunt (PRESERFLO, P) produces nycthemeral (24h) intraocular pressure (IOP) profiles different from ab-interno trabeculectomy (Trabectome, T). P is a flow restrictor that drains fluid into the sub-tenon space. In contrast, T increases conventional outflow, which is limited by episcleral venous pressure. Methods: In this prospective cohort, we analyzed 68 patients (34 P and 34 T) who presented for 24-h IOP monitoring 6 to 12 months after surgery. IOP and tonographic outflow facility were measured in the habitual position using a pneumatonometer. The IOP variation was considered the primary outcome measure. Glaucoma medications were also compared. Results: P had a higher baseline IOP than T (24.8±10.0 vs. 17.3±7.9 mmHg, p=0.001). Postoperatively, P and T had similar nycthemeral IOP profiles, but IOP in P was significantly lower than in T, except at 4 pm. P had a lower absolute IOP variation than T (5.8±2.6 vs. 7.1±2.7 mmHg, p=0.049). The relative IOP variation was similar in both (34.8±13.2 vs. 37.2±13.1, p=0.45) as was the tonographic outflow facility (0.35±0.23 vs. 0.26±0.18 µl/min/mmHg, p=0.097). Conclusion: Nycthemeral IOP profiles of P and T were similar, but P had lower IOPs and less variation than T. This could reflect how T, unlike P, is more impacted by habitual, positional factors, especially at night.

Urban air quality is increasingly becoming a cause for concern for the health of the human population. The poor air quality is already wreaking havoc in major cities of the world, where serious health issues and reduction of average human life by a factor of years are reported. The air quality in developing countries can become worse as they undergo development. The urban air quality varies non-linearly depending upon the various factors such as land use, industrialization, waste disposal, traffic volume, etc. To address this problem, it is necessary to look at the plethora of available literature from multiple perspectives such as types and sources of pollutants, meteorology, urban mobility, urban planning and development, health care, economics, etc. In this paper, we provide a comprehensive survey of the state-of-the-art in urban air quality. We first review the fundamental background on air quality and present the emerging landscape of urban air quality. We then explore the available literature from multiple urban air quality measurement projects and provides the insights uncovered in them. We then take a look at the sources that are significantly contributing to polluting the air quality. Finally, we highlight open issues and research challenges in dealing with urban air pollution.

Stumbling during gait is commonly encountered in patients who suffer from mild to serious walking problems, e.g. after stroke, in osteoarthritis, or amputees using a lower leg prosthesis. Instead of self-reporting, an objective assessment of the amount of stumbles in daily life would inform clinicians more accurately and enable the evaluation of treatments that aim to achive a safer walking pattern. An easy to use wearable might fullfill this need. The goal of the present study was to investigate whether a single inertial measurement unit (IMU) placed at the shank and machine learning algorithms could be used to detect and classify stumbling events in a dataset comprising of a wide variety of daily movements. Ten healthy test subjects were deliberately tripped by an unexpected and unseen obstacle while walking on a treadmill. The subjects stumbled a total of 276 times, both using an elevating recovery strategy and a lowering recovery strategy. Subjects also performed multiple Activities of Daily Living. During data processing, an event-defined window segmentation technique was used to trace high peaks in acceleration which could potentially be stumbles. In the reduced dataset, time windows were labelled with the aid of video annotation. Subsequently, discriminative features were extracted and fed to train seven different types of machine learning algorithms. Trained machine learning algorithms were validated using leave-one-subject-out cross-validation. Support Vector Machine (SVM) algorithms were most succesful, and could detect and classify stumbles with 100% sensitivity, 100% specificity and, 96.7% accuracy, in the independent testing dataset. The SVM algorithms were implemented in a user-friendly, freely available, stumble detection app named Stumblemeter. This work shows that stumble detection and classification based on SVMs is accurate and ready to apply in clinical practise.

Wearable vital signs monitoring and specially the electrocardiogram have taken important role due to the information that provide about high-risk diseases, it has been evidenced by the needed to increase the health service coverage in home care as has been encouraged by WHO. Some wearables devices have been developed to monitor the ECG in which the location of the measurement electrodes is modified respect to the Einthoven model. However, mislocation of the electrodes on the torso can lead to the modification of acquired signals, diagnostic mistakes and misinterpretation of the information in the signal. This work presents a volume conductor evaluation and an ECG signal waveform comparison when the location of electrodes is changed, to find a electrodes’ location that reduces distortion of interest signals. In addition, effect of motion artifacts and electrodes’ location on the signal acquisition are evaluated. A group of volunteers was recorded to obtain ECG signals, the result was compared with a computational model of the heart behavior through the EA ECG, DTW and SNR methods to quantitatively determine the signal distortion. It was found that while the Einthoven method is followed, it is possible to acquire the ECG signal from the patient’s torso or back without a significant difference, and the electrodes position can be moved 6cm at most from the suggested location by the Einthoven triangle in Mason-Likar’s method.

Layer-wise 3D surface morphology information is critical for the quality monitoring and control of additive manufacturing (AM) processes. However, most of the existing 3D scan technologies are either contact or time consuming, which are not capable of obtaining the 3D surface morphology data in a real-time manner during the process. Therefore, the objective of this study is to achieve real-time 3D surface data acquisition in AM, which is achieved by a supervised deep learning-based image analysis approach. The key idea of this proposed method is to capture the correlation between 2D image and 3D point cloud, and then quantify this relationship by using a deep learning algorithm, namely, convolutional neural network (CNN). To validate the effectiveness and efficiency of the proposed method, both simulation and real-world case studies were performed. The results demonstrate that this method has strong potential to be applied for real-time surface morphology measurement in AM, as well as other advanced manufacturing processes.

Study evaluates the characteristics and clinical course of patients with iris cysts in the long term of follow-up (24-48 months). We analyzed retrospectively the medical records of 39 patients with iris cysts (27 female and 12 male). Age, visual acuity, intraocular pressure (IOP), slit-lamp evaluation, and ultrasound biomicroscopy images were assessed. The mean age at diagnosis was 40.6±17.48 years. 30 (76.9%) cysts were peripheral, 5 (12.8%) cysts located at the pupillary margin, 2 (5.1%) cysts were midzonal and 2 (5.1%) multichamber cysts extended from the periphery to the pupillary margin. 23 (59%) cysts were in the lower temporal quadrant, 11 (28.2%) cysts in the lower nasal quadrant, and 5 (12.8%) cysts in the upper nasal quadrant. Cyst size was positively correlated with the age of the patients (rs = 0.38, p = 0.003) and negatively correlated with visual acuity (rs = -0.42, p = 0.014). No cyst growth was documented. The only complication was an increase in IOP in 3 (7.7%) patients with multiple cysts. The anatomical location of cysts cannot differentiate them from solid tumors. The vast majority of cysts are asymptomatic, do not increase in size, and do not require treatment in long-term follow-up.

There are some limitations in the null test measurement in the stitching interferometry. In order to meet the null test conditions, the moving distance between the sub-apertures often deviates from the theoretical preset distance, which leads to a position deviation of sub-apertures under measurements. To overcome this problem, an algorithm for data processing is proposed. We used iterative calculation of the deviations between the sub-apertures to adjust their positions, to ensure the local validity of the linear approximation algorithm and realize the exact stitching. A cylindrical lens as an object for experimental examination of the proposed method was taken. The obtained results demonstrate the validity, reliability and feasibility of our iterative stitching algorithm.

In this study, lithium reaction distributions, dependent on charge-discharge rate, were nondestructively visualized for a commercial lithium-ion battery, using the Compton scattering imaging technique. By comparing lithium reaction distributions obtained from two different charge-discharge speeds, residual lithium ions were detected at the center of the negative electrode on a fully discharged state, by relatively high-speed discharge rate. Moreover, we confirmed that inhomogeneous reactions were facilitated on a relatively high-speed charge-discharge rate, in both the negative and positive electrodes. A feature of our technique is that it can be applied to commercially used lithium-ion batteries, because it uses high-energy X-rays with a high penetration power. Our technique thus opens a novel analyzing pathway for developing advanced batteries.

It is one of very important and basic problem in compute vision field that recovering depth information of objects from two-dimensional images. In view of the shortcomings of existing methods of depth estimation, a novel approach based on SIFT (the Scale Invariant Feature Transform) is presented in this paper. The approach can estimate the depths of objects in two images which are captured by an un-calibrated ordinary monocular camera. In this approach, above all, the first image is captured. All of the camera parameters remain unchanged, and the second image is acquired after moving the camera a distance d along the optical axis. Then image segmentation and SIFT feature extraction are implemented on the two images separately, and objects in the images are matched. Lastly, an object depth can be computed by the lengths of a pair of straight line segments. In order to ensure that the best appropriate a pair of straight line segments are chose and reduce the computation, the theory of convex hull and the knowledge of triangle similarity are employed. The experimental results show our approach is effective and practical.

In this paper new upper limits on the parameters of the Continuous Spontaneous Localization (CSL) collapse model are extracted. To this end the X-ray emission data collected by the IGEX collaboration are analyzed and compared with the spectrum of the spontaneous photon emission process predicted by collapse models. This study allows to obtain the most stringent limits within a relevant range of the CSL model parameters, with respect to any other method. The collapse rate $\lambda$ and the correlation length $r_C$ are mapped, thus allowing to exclude a broad range of the parameter space.

The dairy industry relies heavily on milk pasteurization to ensure the safety and quality of milk products. Pasteurization is a process that involves heating milk to a specific temperature for a set period of time to kill harmful bacteria and other pathogens while preserving its nutritional value. recent years, newer techniques such as High Temperature Short Time (HTST) pasteurization have gained popularity due to their efficiency and effectiveness. HTST pasteurization involves rapidly heating milk to a high temperature for a short duration of time, followed by rapid cooling. This process helps to minimize the loss of flavor and nutrients in milk while ensuring its safety. However, there is still a need in the market for a compact and remotely controlled process plant for milk pasteurization. The proposed work aims to address this need by designing a process plant that is not only compact but also remotely controlled, allowing for efficient and convenient operation. can control the process plant remotely, allowing for flexibility and convenience in monitoring and managing the pasteurization process from anywhere with an internet connection

The study of velocimetry is important for characterizing and comprehending the effects of fluid flow, and the Particle Image Velocimetry (PIV) technique is one of the primary approaches for understanding the velocity vector field in a test section. Commercial PIV systems are expensive, with one of the main cost factors being high-speed camera equipment capable of capturing images at high frames per second (fps), rendering them impractical for many applications. This study proposes an evaluation of utilizing smartphones as image acquisition systems for PIV technique application. An experimental setup inspired by the known angular displacement of synthetic particles is proposed. A stepper motor rotates a plate containing an image of synthetic particles on its surface. The motion of the plate is captured by the smartphone camera, and the images are processed using PIVlab-MatLab® software. The use of two smartphones is assessed, with acquisition rates of either 240 fps or 960 fps and varying angular velocities. The results were satisfactory for velocities up to 0.7 m/s at an acquisition rate of 240 fps and up to 1.8 m/s at 960 fps, validating the use of smartphones as a cost-effective alternative for the PIV technique.

In recent years, the concept of Fiducial Reference Measurements (FRM) has been developed to highlight the need for precise and well-characterised measurements tailored explicitly to the post-launch calibration and validation (Cal/Val) of Earth observation satellite missions. The confidence that stems from robust unambiguous uncertainty assessment of space observations is fundamental to assessing the changes in the Earth system and climate model prediction, and delivering the essential evidence-based input for policy makers and society striving to mitigate and adapt to climate change. The underlying concept of an FRM has long been a core element of a Cal/Val program, providing a ‘trustable’ reference against which performance can be anchored or assessed. The ‘FRM’ label was created to embody into such a reference a set of key criteria. These criteria included the establishment of documented evidence of uncertainty with respect to a community-agreed reference (ideally SI-traceable) and specific tailoring to the needs of a satellite mission. It, therefore, facilitates comparison and interoperability between products and missions in a cost-efficient manner. CEOS Working Group Cal/Val (WGCV) is now putting in place a framework to assess the maturity and compliance of a ‘Cal/Val reference measurement’ in terms of a set of community-agreed criteria which define it to be of CEOS-FRM quality. The assessment process is based on a maturity matrix that provides a visual assessment of the state of any FRM against each of a set of given criteria; making visible where it is mature and where evolution and effort needs to be done. This paper provides the overarching definition of what constitutes an FRM and introduces the new CEOS FRM assessment framework.

The calibration of length is related to the national economy and people's livelihood. The traditional calibration of length value was sent the uncalibrated instrument to the laboratory and the intrinsic error of the tested instrument was obtained in the laboratory. However, calibrating the instrument in the site produced additional error. In this article, a remote calibration method of length measurement based on optical fiber information transmission following with a proof of principle system was studied to reduce the additional error. The 1.0-level displacement guide rail was calibrated according to this method. The results showed that the relative error of guide rail displacement under different lengths was within 0.6%. The expanded uncertainties of 10 μm, 100 μm and 1 mm were analyzed respectively. The calibration results meet the actual standards of the guide rail. This optical method is a good candidate for remote calibration.

When undertaking wind assessment around buildings using large eddy simulation (LES), the implementation of the integral length scale at the inlet for inflow generation is controversial, as real atmospheric length scales require huge computational domains. While length scales significantly influence inflow generation in the domain, their effect on the downstream flow field has not yet, been investigated. In this paper, we validate the effectiveness and accuracy of implementing a reduced turbulence integral length scale for inflow generation in LES results at the rooftop of low-rise buildings and develop a technique to estimate the real local length scales using simulation results. We measure the wind locally and calculate the turbulence length scales from the energy spectrum of the wind data and simulation data. According to these results, there is an excellent agreement between the length scale from simulation and measurement when they are scaled with their corresponding freestream/inlet value. These results indicate that a reduced integral length scale can be safely used for LES to provide a reliable prediction of the energy spectrum as well as the length scales around complex geometries. The simulation results were confidently employed to obtain the best location for a wind turbine installation on low-rise buildings.

The growing interest in heat-conducting nanofluids requires highly sensitive methods for analyzing thermal properties. Thermal-lens spectrometry, despite its advantages over classical methods, does not have a general approach to measuring and interpreting results for dispersed systems. In this paper, by the example of nanofluids of silicon oxide in water in a wide range of concentrations and sizes, the selection of measurement parameters for transient and steady-state thermal lensing is justified, and the interpretation of the results of thermal diffusivity measurements is substantiated. The features of measurements of thermal diffusivity by thermal lens spectrometry under stationary state for dispersed systems are considered. Using this approach, it is possible to detect and distinguish thermal effects with high accuracy. For dispersions of silicon oxide, with increasing concentration, the thermal diffusivity passes through a minimum. Silicon oxide dispersions can be used both as a coolant or as a heat-removing liquid by selecting the particle size and concentration.

A variant of the von Neumann-Wigner Interpretation is proposed. Problems arising from the quantum Zeno effect are addressed as we have described previously. We do, however, offer some new, and perhaps unexpected observations. We are accustomed to thinking of wave function collapse as occurring consequent to laboratory measurements. We speculate that, whatever physical correlate of consciousness exists within the brain, it is quantum mechanical in the sense that a brain, left to itself, would eventually decohere into a state no longer compatible with its conscious functioning. Wave function collapse returns it to a state compatible with consciousness. Indeed, this may be its important reason for occurring. A universe without it simply could not play host to conscious brains. The fact that it also prevents us from encountering "absurd" situations in the laboratory is merely a fortunate dividend. Whenever a quantum measurement is made the universe's future history splits into a number of possibilities. This number may be very large or infinite. And we believe consciousness plays a vital role in this happening. A "conscious" universe where quantum measurements are being made allows for an enormous number of equally acceptable world-histories. An "unconscious" one, always evolving in a unitary fashion, allows for only one. If we assume that the decision as to which worldhistory is the real one (i.e. this one) is made at random we see that the universe is overwhelmingly more likely to be "conscious" than not.

The question whether a given set of test items can be considered “identical” is often addressed in terms of the homogeneity of the test material from which said items were taken. However, for some types of matrices – in particular, for matrices consisting of minute separate particles, only some of which carry the analyte under consideration – even in the case of homogenous test material, an irreducible source of variability between test items may remain: the fundamental variability. In this paper, the concept of fundamental variability is explained, and procedures for reducing and characterizing it are described.