Measurements of temperature and salinity in the Amazon River plume in the open ocean of the western tropical North Atlantic are considered. The measurements were carried out using the AML CTD probe in the upper layer and a flow-through system that measures salinity and turbidity of seawater while the vessel is on the way. Additionally, archive oceanographic data from the WOD18 database, data of satellite altimetry measurements (AVISO), and satellite salinity data from Aquarius and SMOS were used. It is shown that the width of the Amazon plume is about 300–400 km, the depth of desalination is from 50 to 100 m. Surface salinity decreases compared to the background (36 PSU) by 0.5 PSU in February and more than by 3 PSU in September during the period of maximum development of the plume, which is determined from satellite measurements of surface salinity. Lagrangian modeling of the back-in-time advection of passive markers simulating freshwater particles was carried out. It was shown that the source of fresh water in the measurement area is the discharge of the Amazon.

Background: In most cases, intra-labyrinthine schwannoma (ILS) occurs in patients with unilateral hearing deterioration or neurofibromatosis type II (NF II). The pattern of localization of these tumors is various but affects mostly the cochlea. Extirpation of the ILS, if hidden by the cochlea modiolus, is difficult under the aspect of complete removal. Therefore, a tissue removal device (TRD) was designed and tested in temporal bones. The principle of handling the new device is a pushing and pipe cleaner handling inside the cochlea. This present study aimed to describe the first in vivo experience with the newly developed TRD for removing cochlear intra-labyrinthine schwannoma. Methods: In three patients, the TRD was used for the tumor removal of ILS. In two patients with a cochlear schwannoma in combination with a cochlea implantation and one patient suffering from NF II, a cochlear schwannoma was removed with the TRD. The access was performed with a posterior tympanotomy, an enlarged round window approach, and an additional second-turn access. The device was inserted and extracted gradually from the second turn access until the rings were visible in the second turn access. By pushing and pipe cleaner handling, the tumors were removed. An MRI control was performed on the day postoperatively with a T1 GAD sequence. Results: Tumor removal with the TRD was performed in a 15-minute procedure. MRI control confirmed a complete removal on the postoperative day in both cases. Conclusion: In vivo handling of the device confirmed a straightforward handling for tumor removal. MRI scanning showed a complete removal of the tumor by the TRD.

Chorioamnionitis (CA) at term of pregnancy can have infectious and/or inflammatory origin and is associated with adverse outcomes. Triple I (Intrauterine Inflammation, Infection or both, TI) has been proposed to reduce the overdiagnosis of infection and the neonatal overtreatment. The aim of the study is to identify clinical and histological variables predicting adverse outcomes when TI has been suspected and/or confirmed. This retrospective cohort study included 404 pregnancies ≥37 g.a. that were divided into 5 all-inclusive and mutually exclusive groups. TI was defined according to NICHD definition of 2015 and it could be confirmed (TI+) or not (TI-) by histological examination. Signs of infection/inflammation not respecting the definition of TI were classified as “Clinical suspicion”, supported (CS+) or not (CS-) by histology. Histological chorioamnionitis (HCA) without clinical manifestation represented fifth group. Whole Placental Involvement (WPLI), was defined as a histological inflammation involving maternal and fetal side. There were 113 TI+, 30 TI-, 186 CS+, 35 CS- and 40 isolated HCA. WPLI was diagnosed in 133 cases (39.2%). Composite neonatal outcome (CNO) occurred in 114 cases (28.2%) while composite maternal outcome (CMO) occurred in 192 cases (47.5%). TI+ compared to CS+ was more predictive of CNO (p=0.001), CMO (p<0.001) and WPLI (p=0.005). WPLI was related both to CNO (p<0.001) and CMO (p=0.046). TI+ and WPLI showed similar sensitivity but different specificity in predicting CNO. At logistic regression, CNO was independently predicted by TI+ (OR 2.21; p=0.001) and by WPLI (OR 2.23; p=0.001). TI, compared to CS, is a better predictor of CNO and can be useful for the identification of newborns at risk.

In this perspective article, we ponder topographical enhancements of artificial neural networks. In our recent paper in JMLR, we proved a quasi-equivalence between the network width and depth and also discussed the power of intra-links, which can be viewed as network height. In 1982, Hopfield published a network to model human associative memory, which contains many loops for dynamic evolution toward fixed points. Based on noising-denoising loops, diffusion models are recently developed to enable Bayesian modeling and inference with big data. Furthermore, we envision development of multi-AI-agent systems through “netware” engineering as a quantum leap of software engineering for emergent behaviors and autonomous AI at individual and population levels. We believe that the novel use of links and loops in space and time via multi-scale coupling would catalyze the next-generation neural networks.

Abstract: (1) Background: Minimally-invasive sacroiliac joint (SIJ) fusion is the preferred surgical intervention to treat chronically severe pain associated with SIJ degeneration and dysfunction. (2) Methods: This paper details the ten-step surgical procedure associated with the postero-inferior approach using the PsiF™DNA Sacroiliac Joint Fusion System. (3) Results: The posterior surgical approach with an inferior operative trajectory (postero-inferior) utilizes easily identifiable landmarks to provide the safest, most direct access to the articular joint space for transfixing device placement. Implanting the device through the subchondral bone, provides maximum fixation and stabilization of the joint by utilizing an optimal amount of cortical bone-implant interface. Approaching the joint from the inferior trajectory also places the implant perpendicular to the S1 endplate at a “pivot point” near the sacral axis of rotation, which addresses the most significant motion of the joint. (4) Conclusions: Further observational data from real-world clinical use are encouraged to further validate this procedure as the surgical preference for minimally-invasive SIJ fusion.

Given of the outstanding versatile properties, the multilayered anti-corrosion coatings have drawn great interests in academic and engineering fields. However, the application of multilayered coatings is restricted by some limitations such as low interlayer compatibilities, harsh preparation process, etc. This work introduced a composite film fabricated on 2A12 aluminum alloy surface, including an anodic oxide film, a sol-gel film as well as a layer-by-layer (LBL) self-assembling film from bottom to top. The microstructure and elemental characterization indicated that the finish of the coating with the LBL film resulted in a closely connected multilayered coating with a smoother surface. The anticorrosion performance was systematically evaluated in the simulated corrosive medium and neutral salt-spray environment. The intergrated coating with the LBL film presented an excellent anticorrosion ability with the system impedance over 108 Ω•cm² and the self-corrosion current density two orders of magnitude lower than that of the other coatings. After the acceleration test in salt-spray environment, the multilayered coatings could still show a good protective performance with almost no cracks and no penetration of chloride ions. It is believed that the as-constructed multilayered coating with high corrosive properties and fine surface state will have promising applications in the field of anticorrosion engineering.

Introduction. Intra-abdominal cystic formations represent heterogeneous pathologies with varied localization and clinical manifestation. The first challenge of a giant intra-abdominal cystic lesion is identifying the organ of origin. The clinical presentation of intra-abdominal cystic lesions varies from acute manifestations to non-specific symptoms or accidental discovery. Case presentation: A 2-year-old girl presents to the emergency unit with a fever of 38.5 Celsius, loss of appetite, and apathy. The investigations showed a gigantic intra-abdominal mass whose organ belonging could not be specified. Postoperatively, a giant mesenteric lymphangioma was evident, which was completely excised. Discussions Giant cystic formations modify the anatomical reports and become space-replacing formations, and the starting point is even more challenging to assess preoperatively. Nevertheless, the careful evaluation of the characteristics of the formation, the effect on the adjacent organs, the age of the patient, and the clinical picture can provide elements of differential diagnosis.

Intra-abdominal pressure (IAP) elevation during capnoperitoneum can cause adverse cardiovascular and respiratory effects. This study aimed to determine if a sequentially increased IAP affects cardiovascular and respiratory variables in anesthetized dogs and evaluate the effects of constant rate infusion of dexmedetomidine (Dex) on cardiovascular and respiratory variables with increased IAP. Five dogs were anesthetized, instrumented, and the Veress needle was equipped to adjust the IAP using a carbonic anhydrase insufflator. Stabilization was conducted for 1 h, and physiological variables were measured in IAPs of 0, 5, 10, 15, and 20 mmHg and after desufflation. After the washout period, the dogs underwent similar procedures along with constant rate infusion of dexmedetomidine. Cardiovascular effects of increased IAP up to 20 mmHg were not significant in healthy beagle dogs and those administered with dexmedetomidine. In the control group, the arterial pressure slightly increased, but not statistically significant, at an IAP of 20 mmHg compared with that at baseline (mean arterial blood pressure, p = 0.399; systolic arterial blood pressure, p = 0.293; diastolic arterial blood pressure, p = 0.141). When comparing the control and dexmedetomidine groups, overall significant effects of dexmedetomidine were noted on heart rate, cardiac output, and systemic vascular resistance during the experiment. Respiratory effects were not affected by abdominal insufflation when compared between different IAPs and between the two groups. Overall, an increased IAP of until 20 mmHg did not significantly affect cardiovascular and respiratory variables in both control and dexmedetomidine groups. This study suggests that dexmedetomidine infusion administration is applicable in laparoscopic procedures in healthy dogs.

The study was conducted in coniferous and deciduous old growth forests in two forest complexes located in: i) the fenced area of the Popielno Research Station of the Polish Academy of Sciences, with free-living Polish pony [Polish primitive horse (Equus ferus caballus)], and ii) open Maskulińskie Forest District managed (harvested) forest, without horses. The impact of forest animals on ground cover layer as well as on understory shrub layer and undergrowth, in i) area (horses and other forest animals) was compared with the results in ii) area (forest animals without horses). Very significant differences in the understory and undergrowth (above 0,5 m) layer vegetation communities structure between both areas and type of stands were found. The results suggest that the presence of the Polish horse substantially changed the species composition and increased the species diversity of the ground layer and shrub layer both on coniferous forest and in the deciduous forest habitats. The height of the shrub layer trees was lower by 30% in the area with the Polish horse.

Phagocytosis (and endocytosis) is an unusual cellular process which results in the formation of a novel subcellular organelle, the phagosome. This phagosome contains not only the internalised target of phagocytosis, but also the external medium, creating a new border between extracellular and intracellular environments. The boundary at the plasma membrane is, of course, tightly controlled and exploited in ionic cell signalling events. Although there has been much work on the control of phagocytosis by ions, notable Ca2+ ions influxing across the plasma membrane, increasing our understanding of the mechanism enormously, very little work has been done exploring the phagosome/cytosol boundary. In this paper, we have explored the changes in the intra-phagosomal Ca2+ ion content which occur during phagocytosis and phagosome formation in human neutrophils. Measuring Ca2+ ion concentration in the phagosome is potentially prone to artefacts as the intra-phagosomal environment experiences changes in pH and oxidation. However, by excluding such artefacts, we conclude that there are open Ca2+ channels on the phagosome, which allow Ca2+ ions to ‘drain’ into the surrounding cytosol. This conclusion was confirmed by monitoring the translocation of intracellularly expressed YFP-tagged C2 domain of PKC-γ. This approach marked regions of membrane at which Ca2+ influx occurred, the earliest being the phagocytic cup, and then the whole cell. This paper therefore presents data which has novel implications for understanding phagocytic Ca2+ signalling events, such as peri-phagosomal Ca2+ hotspots, and other phenomena.

Climate change is an issue that is the order of the day, and among the many consequences it has on the environment one is its influence on the amount and frequency of rainfall on our planet, since our water supply depends on them. Therefore, in order to quantify these effects, a rainfall analysis has been carried out using data collected in Bilbao over the last 150 years. Thanks to this, it has been possible to observe that, although the total annual amount seems to suffer a slight decrease, hardly quantifiable with certainty, it is true that the intra-annual patterns are more concentrated at certain times of the year, with greater imbalances between one month and another than in previous years. However, taking into account the capacity of the reservoirs that supply the Greater Bilbao area, it can be concluded that this does not pose any problem for Bilbao's supply, at least at present.

Feline panleukopenia (FPL), a highly contagious and frequently fatal disease of cats, is caused by Feline parvovirus (FPV) and Canine parvovirus (CPV). We characterized the diversity of these Carnivore protoparvovirus 1 variants in 18 faecal samples collected from domestic cats with FPL during an outbreak, using targeted parvoviral DNA metagenomics to a mean depth of >10,000 X coverage per site. All samples comprised FPV alone. Compared to the reference FPV genome, isolated in 1967, 44 mutations were detected. Ten of these were non-synonymous, including 9 in non-structural genes and one in VP1/VP2 (Val232Ile), which was the only one to exhibit inter-host diversity, being present in five sequences. There were five other polymorphic nucleotide positions, all with synonymous mutations. Intra-host diversity at all polymorphic positions was low with sub-consensus variant frequencies (SVF) of >1% except for two positions (2108 and 3208) in two samples with SVF of 1.1 – 1.3%. Intra-host nucleotide diversity was measured across the whole genome (0.7 - 1.5%) and for each gene, and was highest in the NS2 gene of four samples (1.2 – 1.9%). Overall, intra-host viral genetic diversity was limited and most mutations observed were synonymous, indicative of a low background mutation rate and strong selective constraints.

Building deep learning models proposed by third parties can become a simple task when specialized libraries are used. However, a great deal of mystery still surrounds the design of new models or the modification of existing ones. These tasks require in-depth knowledge of the different components or building blocks as well as their dimensions. This information is limited and broken up in different literature. In this article, we collect and explain in-depth the building blocks to design deep learning models, starting from the artificial neuron to the concepts involved in building deep neural networks. Furthermore, the implementation of each building block is exemplified using the Keras library.

The field of human microbiome and gut microbial diversity research has witnessed a profound transformation, driven by advances in omics technologies. These advancements have unveiled essential connections between microbiome alterations and severe conditions, spurring the development of new frameworks through epidemiological studies. Traditionally, each individual was thought to harbor unique microbial communities acquired early in life, but recent research challenges this belief. The neonatal microbiome's onset, influenced by factors like delivery mode and maternal health, remains a subject of intense debate, hinting at potential intrauterine microbial processes. In-depth research reveals associations between microbiome profiles and specific health outcomes, ranging from obesity to neurodevelopmental disorders. Understanding these diverse microbiome profiles is essential for unraveling the intricate relationships between the microbiome and health outcomes.

Rainfall is a major climate parameter whose variation in space and time influences activities in different weather sensitive sectors such as agriculture, transport, and energy among others. Therefore, accurately forecasting rainfall is of paramount importance to the development of these sectors. In this regard, this study sought to contribute to quantitative forecasting of rainfall over Eastern Uganda through assessing the Weather Research and Forecasting model’s ability to simulate the intra–seasonal characteristics of the September to December rain season. These were: onset and cessation dates; wet days and lengths of the wet spells. The data used in the study included daily ground rainfall observations and lateral and boundary conditions data from the National Centers for Environmental Prediction (NCEP) final analysis at 1 0 horizontal resolution and at a temporal resolution of 6 hours for the entire study period were used to initialize the Weather Research and Forecasting (WRF) model. The study considered four weather synoptic weather stations namely; Jinja, Serere, Soroti and Tororo. The results show that the WRF model generally simulated fewer wet days at each station except for Tororo. Also, the WRF model simulated earlier onset and cessation dates of the rainfall season and overestimated the length of the wet spells.

This research work deals with the formulation of numerical scheme with algorithm to compute singularly perturbed partial differential equations(SP-PDEs) involving a significant negative shift. The problem involves small parameter which causes a rapidly changing boundary layers in the vicinity of a body, and the negative shift term causes interior layer. Such appearance of an abruptly varying layers causes difficulties to find the exact solution and it is not adequate to employ classical numerical methods. The technique presented in this research work simplifies these challenges and yields accurate numerical solution.The stability and convergence analyses of the methods are examined and proven. To test the developed technique, numerical experiments are carried out and confirmed with theoretical analysis.

Polydopamine (PDA) deposition, obtained from the oxidation of dopamine and other catecholamines is an universal way to coat all known materials with a conformal coating which can subsequently be functionalyzed at will. The structural analogies between polydopamine and eumelanin, the black-brown pigment of the skin, incited to produce stable polydopamine nanoparticles in solution instead of amorphous precipitates obtained from the oxidation of dopamine. Herein, we demonstrate that size controlled and colloidally stable PDA based nanoparticles can be obtained in acidic conditions, where spontaneous auto-oxidation of dopamine is suppressed, using sodium periodate as the oxidant and a protein like alkaline phosphatase as a templating agent. The size of the PDA@Alp nanoparticles depends on the dopamine/enzyme ratio and the obtained particles display the enzymatic activity of alkaline phosphatase with an activity extending up to two weeks after particle synthesis. The PDA@ alkaline phosphatase (Alp) nanoparticles can be engineered in polyelectrolyte multilayered films to potentially design model biosensors.

Curcumin is a promising anti-cancer drug but its applications in cancer therapy are limited due to its poor solubility, short half-life and low bioavailability. In this study, curcumin loaded magnetic alginate / chitosan nanoparticles were fabricated to improve the bioavailability, uptake efficiency and cytotoxicity of curcumin to MDA-MB-231 breast cancer cells. Alginate and chitosan were deposited on Fe3O4 magnetic nanoparticles based on their electrostatic properties. The sizes of the nanoparticles (120-200 nm) were within the optimum range for drug delivery. Sustained curcumin release was obtained use the nanoparticles with the ability to control the curcumin release rate by altering the number of chitosan and alginate layers. Confocal fluorescence microscopy results showed that targeted delivery of curcumin with the aid of magnetic field were achieved. The FACS assay indicated that MDA-MB-231 cells treated with curcumin loaded nanoparticles had a 3-6 folds uptake efficiency to those treated with free curcumin. MTT assay indicated that the curcumin loaded nanoparticles exhibited significantly higher cytotoxicity toward MDA-MB-231 cells than toward HDF cells. The sustained release profiles, enhanced uptake efficiency and cytotoxicity to cancer cells as well as the targeting potential make MACPs a promising candidate for cancer therapy.

Cartilage degeneration is a characteristic of osteoarthritis (OA) which is often observed in aging populations. This degeneration is due to the breakdown of articular cartilage (AC) mechanical and tribological properties, primarily attributed to lubrication failure. Understanding the reasons behind these failures and identifying potential solutions could have significant economic and societal implications, ultimately enhancing the quality of life. This review provides an overview of developments in the field of AC, focusing on its mechanical and tribological properties. The emphasis is on the role of lubrication in degraded AC, offering insights into its structure and function relationship. Further it explores the fundamental connection between AC mechano-tribological properties and the advancement of its degradation and puts forth recommendations for strategies to boost its lubrication efficiency.

The ultrasound guided viscosupplementation of the hip joint with hyaluronic acid(HA)is considered a standard procedure among the conservative treatments for hip arthritis.The aim of the study was to evaluate the clinical benefit and the incidence of adverse events of the technique in a obseravtional study at one year follow up. We evaluated a consecutive series of 85 patients with a diagnosis of symptomatic arthritis that performed intra-articular ultrasound-guided hyaluronic acid injections. The scales used for evaluation were modified Harris Hip Score(mHHS),WOMAC (Western Ontario and McMaster University),Hip Outcome Score (HOOS) with subscale Sport (HOOSs), for pain the Visual Analogic Scale (VAS).The patients were classified according to Tonnis’ radiological classification of arthrosis (range 0-3):20 patients(grade 0),32(grade 1),18(grade 2),15(grade 3).At last follow up all the scales increased:mHHS from 59.35 to 82.1,HOOS from 69.45 to 78.53,HOS Sport from 47.4 to 58.11,VAS from 6.09 to 3.97,WOMAC from 33.2 to 31.5 (p<0.05 for all the parameters);13/85 requested arthroplasty. Based on our findings, indication for use of hyaluronic acid is limited to patients with mild to moderate arthritis.Patients in advanced arthritis refusing replacement surgery and asking for this treatment should be informed about the poor results of the technique even in the short term follow up.

The polymerase chain reaction (PCR) is a widely used technique in the biosciences and has become increasingly popular in recent years. One of the key elements of this technique is the use of a DNA polymerase that is heat-stable and retains fidelity during the process. To this end, archaeal Fam-ily-B DNA polymerases are preferred due to their high thermostability and fidelity. In particular, the DNA polymerase from Thermus aquaticus (Taq DNApol) is widely utilized in PCR procedures. In this work, a novel in-silico structure-based methodology was employed to examine the most heat-tolerant DNA polymerase available. In spite of this, Thermococcus kodakarensis and Geobacillus stearothermophilus DNApol are more stable and heat-tolerant DNApols due to their high number of intra-protein interactions. Variations in the content of polar amino acids also played a significant role in the increase in heat stability. A further factor contributing to the stability of proteins is the stabilization of helix in secondary structure through the use of charged amino acids. DNApol from these organisms has been shown to be suitable for use in PCR, as well as in other biological processes able to withstand high temperatures. In this study, it has been demonstrated that im-provements in PCR performance can be easily obtained by blending elements from closely related archaeal polymerases, a strategy that may, in the future, be extended to other archaeal polymer-ases. This approach allowed for a comprehensive analysis of the enzyme's thermal stability and fidelity, leading to an improved understanding of the polymerase's properties and potential ap-plications

Background: Elevated fasting plasma glucose and visceral fat area (VFA) is highly prevalent in obese adults. This study investigated the associations between systemic arterial hypertension (SAH) and laboratory, anthropometric, heart rate variability (HRV), and obstructive sleep apnea markers. Methods: Cross-sectional study with 95 obese patients treated at Obesity Treatment and Surgery Center, located in Salvador, BA, Brazil. SAH data were obtained from electronic medical records of patients. To evaluate the association of SAH with the predictor variables, the sample was stratified in Normotense Group (NG) and Hypertensive Group (HG), and laboratory markers, body composition, polysomnography data, and HRV were measured. Results: The average age of the NG was 36.3 ± 10.1 and HG 40.4 ± 10.6 years, 73.7% were women in the NG and 57.9% in HG; 82.4% in HG had insulin resistance. In the multivarious logistics regression model with adjustments age, sex, height, and oxyhemoglobin saturation, SAH was inversely associated with fasting plasma glucose mg/dL (odds ratio [OR] = 0.96; 95% interval confidence [CI] = 0.92 - 0.99) and VFA cm² (OR = 0.98; 95% CI = 0.97 - 0.99). The area under curve the VFA was 0.728; CI 95% (0.620 - 0.836) and fasting plasma glucose 0.693; CI 95% (0.582 - 0.804). Conclusions: Lower VFA and fasting plasma glucose concentrations were inversely associated with SAH. These results indicate opportunities to improve the outcome in obese patients through counseling and clinical interventions.

Purpose: To evaluate seasonal variation in intra-ocular pressure (IOP) with and without short tear break-up time (SBUT, BUT ≤ 5 s). Methods: This study enrolled 176 patients who visited one of six eye clinics in Japan for IOP measurement at every season. The mean patient age was 67.9 years, including 79 males. We compared the seasonal variation in IOP (mean ± SD) across spring (Mar-May), summer (Jun-Aug), fall (Sep-Nov), and winter (Dec-Feb). Results: The IOP (mmHg) in winter and summer, respectively, was 12.8 ± 3.7 and 12.8 ± 3.1 for non-glaucoma patients without SBUT (n = 47, P = 0.964), 14.8 ± 3.4 and 13.3 ± 3.4 for non-glaucoma patients with SBUT (n = 57, P < 0.001), 14.3 ± 3.2 and 14.1 ± 3.4 for glaucoma patients without SBUT (n = 36, P = 0.489), and 13.3 ± 3.0 and 11.6 ± 2.9 for glaucoma with SBUT (n = 36, P < 0.001). Seasonal variation was largest across the seasons in the glaucoma with SBUT group, and the magnitude of seasonal variation correlated with BUT (β = 0.228, P = 0.003). Conclusions: Seasonal variation tended to be larger in patients with SBUT than those without SBUT.

Purpose: The aim of present study was to compare the treatment results of daily cisplatin (CDDP), weekly docetaxel (DOC) intra-arterial infusion chemotherapy combined with radiotherapy (DIACRT) regimen and weekly CDDP intra-arterial infusion chemotherapy combined with radiotherapy (WIACRT) for patients with tongue cancer. Materials and Methods: Between January 2007 and December 2016, a total of 11 patients treated with WIACRT and 45 patients treated with DIACRT were enrolled in present study. In DIACRT group, 25 patients had T2, 20 patients had T3. A total of 9 patients had T2 and 2 had T3 in WIACRT (p = NS). In DIACRT, the treatment schedule consisted of intra-arterial chemotherapy (DOC, total 60 mg/m²; CDDP, total 150 mg/m²) and daily concurrent radiotherapy (RT) (total, 60 Gy). In WIACRT, the treatment schedule consisted of intra-arterial chemotherapy (CDDP, total 360 mg/m²) and daily concurrent RT (total, 60 Gy). Results: The median follow-up periods for DIACRT and WIACRT were 61 and 66 months respectively. The 5-year local control (LC) and overall survival (OS) rate were 94.5% and 89.6% for DIACRT group, 60.6% and 63.6% for WIACRT group respectively. The LC rate and OS of DIACRT group were significantly higher than that of WIACRT group. As regards toxicities, no treatment-related deaths were observed during the follow-up periods both in two groups. Conclusions: DIACRT was found to be feasible and effective for patients with tongue cancer and could become a new treatment modality.

Most IoT systems meant for implementing mission-critical systems are multi-layered based. The majority of the computing is done in the services and gateway layer. The Gateway layer connects the Internal section of the IoT to the cloud through the Internet. The failure of any node between the services servers and the gateways will isolate the entire network leading to zero tolerance. A networking topology is required to connect the service servers to the gateways, yielding 100% fault tolerance. Empirical formulation of the model chosen to connect the service’s servers to gateways through routers is required to compute the fault tolerance of the network. Rectangular and Interstitial Mesh have been proposed in this paper to connect the service servers to the gateways through the servers that yield 0.999 fault tolerance of the IoT network. An empirical formulation is also presented using which the Fault tolerance of the IoT network can be computed. An enhancement of 11% in the fault tolerance capability of an IoT network has been achieved by implementing Rectangular and Interstitial Mesh in the gateway layer of the network.

The design and engineering of antibacterial materials is key for preventing bacterial adherence and proliferation in biomedical and house-hold instruments. Silver nanoparticles (AgNPs) and chitosan (CHI) are broad-spectrum antibacterial materials with different properties, whose combined application is currently under optimization. This study proposes the formation of antibacterial films with AgNPs embedded in carboxymethylcellulose/chitosan multilayers by the layer-by-layer (LbL) method. The films were deposited onto nanoporous silicon (nPSi), an ideal platform for bioengineering applications, due to its biocompatibility, biodegradability, and bioresorbability. We focus on two alternative multilayer deposition processes: cyclic dip coating (CDC) and cyclic spin coating (CSC). The physicochemical properties of the films were the subject of microscopic, microstructural and surface-interface analyses. The antibacterial activity of each film was investigated against Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) bacteria strains as model microorganisms. According to the findings, CDC technique produced multilayer films with higher antibacterial activity for both bacteria compared to the CSC method. Bacteria adhesion inhibition was observed from only 3 cycles. The developed AgNPs-multilayer composite film offers advantageous antibacterial properties for biomedical applications.

Cadmium telluride (CdTe), a metallic dichalcogenide material, has been utilized as an absorber layer for thin film-based solar cells with appropriate configurations, and the SCAPS-1D structures program has been used to evaluate the results. In both known and developing thin film photovoltaic systems, a CdS thin film buffer layer has been frequently employed as a traditional n-type heterojunction partner. In this study, numerical simulation was used to find a suitable non-toxic material for the buffer layer instead of CdS, among various types of buffer layers (ZnSe, ZnO, ZnS, and In2S3), and carrier concentrations for the absorber layer (NA) and buffer layer (ND) were varied to determine the optimal simulation parameters. carrier concentrations (NA from 2 x 1012 cm-3 to 2 x 1017 cm-3 and ND from 1 x 1016 cm-3 to 1 x 1022 ??−3) have been differed. The results showed that the CdS as buffer layer based CdTe absorber layer solar cell has the highest efficiency (?%) of 17.43%. Furthermore, high conversion efficiencies of 17.42% and 16.27% have been found for ZnSe and ZnO based buffer layers, respectively. As a result, ZnO and ZnSe are potential candidates for replacing the CdS buffer layer in thin-film solar cells. Here, the absorber (CdTe) and buffer (ZnSe) layers were chosen to improve the efficiency by finding the optimal density of the carrier concentration (acceptor and donor). The simulation findings above provide helpful recommendations for fabricating high-efficiency metal oxide-based solar cells in the lab.

Glucose-sensitive films were prepared by the layer-by-layer (LbL) deposition of poly(ethyleneimine) (H-PEI) solution and DNA solution (containing glucose oxidase (GOx)). H-PEI/DNA+GOx multilayer films were constructed using electrostatic interactions. The (H-PEI/DNA+GOx)5 film was then partially decomposed by hydrogen peroxide (H2O2). The mechanism for the decomposition of the LbL film was considered to involve a more reactive oxygen species (ROS) that was formed by the reaction of hemin and H2O2, which then caused nonspecific DNA cleavage. GOx present in the LbL films reacts with glucose to generate hydrogen peroxide. Therefore, decomposition of the H-PEI/DNA+GOx)5 film was observed when the thin film was immersed in a glucose solution. A (H-PEI/DNA+GOx)5 film exposed to a glucose solution for periods of 24, 48 72, and 96 h indicated decomposition of the film increased with the time. The rate of LbL film decomposition increased with the glucose concentration. At pH and ionic strength close to physiological conditions, it was possible to slowly decompose the LbL film at a sub-millimolar glucose concentration.

During the COVID-19 pandemic, immunosuppressed patients showed prolonged SARS-CoV-2 infections, with several studies reporting the accumulation of mutations in the viral genome. The weakened immune system present in these individuals, along with the effect of antiviral thera-pies, are thought to create a favourable environment for intra-host viral evolution and have been linked to the emergence of new viral variants, which strongly challenged the containment measures and some therapeutic treatments. To assess whether an impaired immunity could lead to an increased instability of viral genomes, longitudinal nasopharyngeal swabs were collected from eight immunocompromised patients and fourteen non-immunocompromised subjects, all undergoing SARS-CoV-2 infection. Intra-host viral evolution was compared between the two groups through deep sequencing, exploiting a probe-based enrichment method to minimize the possibility of artefactual mutations commonly generated in amplicon-based methods, which heavily rely on PCR amplification. Although, as expected, immunocompromised patients expe-rienced significantly longer infections, the acquisition of novel intra-host viral mutations was similar between the two groups. Moreover, a thorough analysis of viral quasispecies showed that the variability of viral populations in the two groups is comparable not only at the consensus level, but also when considering low frequency mutations. This study suggests that a compro-mised immune system alone does not affect SARS-CoV-2 within-host genomic variability.

Autologous micrografting technology (AMT®) involves the use of autologous micrografts to stimulate/enhance the repair of damaged tissue. This study assessed the efficacy and safety of the AMT® procedure in patients with early stages of knee osteoarthritis. Briefly, the AMT® procedure involved extraction of auricular cartilage, disaggregation using the Rigeneracons® SRT in 4.0 mL of saline solution and injection of the disaggregated micrografts into the external femorotibial compartment area of the affected knee. Ten patients (4 men, 6 women; age range: 37─84 years) were included in the study. In all patients, there was a steady improvement in knee instability, pain, swelling, mechanical locking, stair climbing and squatting at 1- and 6-months post-procedure. Improvement in mobility was observed as early as 3 weeks post-procedure in 2 patients. Significant improvements were seen in mean scores of all five subscales of Knee Injury and Osteoarthritis Outcome Score (KOOS [KOOS symptoms, KOOS pain, KOOS ADL, KOOS sport and recreation, and KOOS quality-of-life]) between pre-procedure and 1- and 6-months post-procedure (all p≤0.05). Autologous auricular cartilage micrografts obtained by AMT® procedure (using Rigenera® technology) is an effective and safe protocol in the treatment of early-stage knee osteoarthritis. These encouraging findings need to be validated in a larger patient population.

The free energy principle (FEP) is a mathematical and scientific principle that describes the relationship between the physical behavior of a dynamical system and the interpretation of such behavior as carrying out inference. It blurs the boundary between the ontological mode of the system of interest and the epistemological significance it acquires through its dynamic interaction with the environment. New materialism (or neo-materialism), despite lacking a single definition, refers to a range of emerging perspectives that attempt to dismantle the long-held divisions between ontology, epistemology, and even ethics, with the aim of achieving a comprehensive transformation of naturalized thinking. In this context, new materialism provides powerful tools to reframe some of the conceptual foundations of the FEP. This paper is the first in a series that aims to systematically construct a neo-materialistic perspective for the FEP, exploring its wide-ranging implications. It serves as an introduction to the series, arguing for the justification of deploying new materialism to reframe the FEP and introducing some essential concepts to be utilized in developing a neo-materialistic account of the FEP.

Cluster-based routing in Mobile Ad-Hoc Networks is considered one of the convenient methods of routing. The existence of Cluster Head (CH) in a group of nodes for data forwarding improves the performance of routing in terms of routing overhead and power consumption. In this paper, a clustering algorithm using hierarchical routing for mobile ad hoc networks is proposed. In the proposed method, first, clusters are formed by the FLOC clustering method with low overlapping. Then, according to the most important network criteria, including hop count, noise ratio, distance, remaining energy, and link expiration time, head clusters are selected based on the weighting algorithm. To transfer data in the proposed method, two types of communication are used, e.g., inter-cluster communication and intra-cluster communication in which the shortest path to the target cluster is selected. The proposed P-METHOD technique is based on hierarchy and clustering as well as using a weighted algorithm that reduces delay in data transmission on the network. Moreover, P-METHOD is evaluated here via extensive simulations carried out in NS-2. The simulation results indicate that the MANET network performance metrics are improved in terms of average throughput, Packet Delivery Ratio (PDR), delay, residual energy, and lifetime.

In eastern part of Ethiopia groundnut is very commonly intercropped with sorghum. Even though intercropping of sorghum with groundnut is practiced in the eastern part of Ethiopia the population density at what ratio should not be known. Therefore determining the population ratio is found to be crucial to draw management options. The study was conducted at two locations at Fadis (on station) and Babile (sub- station). Sorghum variety (Teshale) and groundnut (Fetene) were used as planting materials. All agronomic data were collected and analyzed by using GenStat software. Significant different were obtained among the treatments. The research result showed that, there were significance difference for both sorghum and ground nut yield per hectare in the years (2014 and 2015) among treatments. The result over time(in 2014 and 2015) at Fadis and Erer showed that the highest sorghum and groundnut yield per hectare were obtained/harvested from the intra row spacing of 25cmx20cm and 30cmx20cm intercropping sorghum with ground nut system with (1.27 and 1.31) respectively. The highest LER (1.31) and highest GMV (10218.00 ETBr/ha) were obtained from the intercropping of 30cmx20cm (Sorghum & groundnut). Clearly showed that, with intercropping of sorghum and Groundnut, it is possible to produce additional yield of sorghum without significant reduction in groundnut yield. As a result of this, the intra spacing of the main crop (sorghum) 25cm and 30cm and for the subsidiary crop (groundnut) 20cm was recommended for further production in the study areas of eastern Harerghe zone and similar agro-ecologies.

The design of multifunctional microcarriers has attracted significant attention because they combine various functions within a single system. In this study, we developed a set of multi-layered hydrogel microcarriers, which were first loaded with chemotherapeutic curcumin (CUR), then using the layer-by-layer (LbL) technique, coated through a polyelectrolyte shell consisting of chitosan (CHIT) or poly(allylamine hydrochloride) (PAH). As an outer layer with antimicrobial function, newly synthesised alkylene quaternary ammonium salt functionalised polyelectrolytes (A-QAS-PEs) were applied. For this purpose, poly(acrylic acid) (PAA) was decorated with dif-ferent hydrophobic side chains (n-hexane and n-dodecane side entities) and different degrees of substitution (m) of quaternary ammonium groups (abbreviated as PAA-C(O)O-(CH2)n-N+(CH3)3(m); n=6,12; m=8-14%). The grafting approach of PAA with the al-kylene quaternary ammonium salt moiety was performed under mild reaction conditions using Steglich esterification followed by quaternisation. The structure of antimicrobial decorated PAA was confirmed by 1H NMR and FTIR, and the mean diameter of all multifunctional microparticles was characterised by SEM. The viscoelastic properties of the functional layers were studied using QCM-D. The release of CUR from the microcarriers was described using a hybrid model, i.e., a combination of first-order kinetics and the Korsmeyer-Peppas model. The antimicrobial activity of functionalised PAA and multilayered CUR-loaded hydrogel microcarriers with quaternary am-monium function was assessed against Staphylococcus aureus and Serratia marcescens by the agar diffusion assay method. Only a limited inhibition zone of PAA was observed, but in the case of both antimicrobial decorated PAA and the corresponding multilayered nanocarriers, the inhibi-tory activity increase was achieved against both strains of bacteria.

In this study, the effect of hot stamping forming process on the properties change of compound layer in Al–Si coated high-strength steel sheet with different thickness was investigated. The coating layer in hot stamped high-strength steel sheet was composed of a diffusion layer and a compound layer. As the hot stamping temperature and holding time for forming increased, the thickness of the compound layer in the Al–Si coated high-strength steel sheet increased. The thickness of coating layer with the hot stamping for 500 sec at 890, 910 and 950 °C was obtained 8.9, 11.8, and 20.6 micrometer, respectively. The thickness of coating layer with hot stamping for 180, 500 and 550 sec at 910 ^oC was obtained 5.7, 11.8, and 17.8 micrometer, respectively. The compound layer in hot stamped high-strength steel sheet with Al–Si coating layer consists of Al_5.4Fe₂ and Fe₂Si phases. In the compound layer, Al and Si were irregularly distributed.

Electrospun nanofiber-supported thin film composite membranes are among the most promising membranes for seawater desalination via forward osmosis. In this study, a high-performance electrospun polyvinylidenefluoride (PVDF) nanofiber-supported TFC membrane was successfully fabricated after molecular layer-by-layer polyelectrolyte deposition. Negatively-charged electrospun polyacrylic acid (PAA) nanofibers were deposited on electrospun PVDF nanofibers to form a support layer consisted of PVDF and PAA nanofibers. This resulted to a more hydrophilic support compared to the plain PVDF nanofiber support. The PVDF-PAA nanofiber support then underwent a layer-by-layer deposition of polyethylenimine (PEI) and PAA to form a polyelectrolyte layer on the nanofiber surface prior to interfacial polymerization, which forms the selective polyamide layer of TFC membranes. The resultant PVDF-LbL TFC membrane exhibited enhanced hydrophilicity and porosity, without sacrificing mechanical strength. As a result, it showed high pure water permeability and low structural parameter values of 4.12 Lm⁻²h⁻¹bar⁻¹ and 221 µm, respectively, significantly better compared to commercial FO membrane. Layer-by-layer deposition of polyelectrolyte is therefore a useful and practical modification method for fabrication of high performance nanofiber-supported TFC membrane.

Two strongly curved areas of the Carpathians in Romania are earthquake-prone: Vrancea - in the South-Eastern Carpathians, and Danubian – in the western edge of the Southern Carpathians. By far the highest seismicity episode in 2023 was recorded in the Southern Carpathians, near Targu Jiu city, of more than 4000 earthquakes. A first ML 5.2 mainshock was recorded on 13 February, followed by a second one, ML 5.7, on 14 February. Our purpose is to provide a first analysis of this sequence in order to explain its extent and unusual development, in time. The possible role of fluids in the middle crust, is discussed in connection with the rather unusual character of the space-time distribution of aftershocks. A large and high-quality dataset is provided by the dense array of seismic stations which has been gradually improved by adding new stations in the epicentral area. The thorough revision of the phase picking and location reveals a few interesting and intriguing features of seismicity that still remain worthy to be further investigated. The database built within this paper provides excellent information not only for Targu Jiu area, but for any other investigation in intra-continental regions characterized by diffuse and sporadic seismic activity.

Physical exercise favorably affects visceral adipose tissue (VAT) which is a risk factor for cardiometabolic diseases. However, many people are unable or unwilling to conduct frequent and intensive exercise programs that have favorable effects on VAT. The present study aimed to determine the effect of the time-efficient and joint-friendly whole-body electromyostimulation (WB-EMS) technology on VAT volume in overweight to obese adults with osteoarthritis of the knee. In total 72 women and men 40-70 years old with femuro-tibial knee osteoarthritis were randomly allocated to WB-EMS (n=36) with 1.5 sessions of 20 min/week for 29 weeks or a usual care control group (CG: n=36) with 6 sessions of physiotherapy. Magnetic Resonance Imaging (MRI) using a non-contrast enhanced 2-point Dixon Gradient Echo Volumetric Interpolated Breath-hold Examination determined VAT. Twelve slices covered a total length of approximately 5 cm from mid L2 to mid L3. In summary, VAT volume increased non-significantly in the CG (p=.261) and decreased non-significantly in the WB-EMS group (p=.160). We failed to determine significant WB-EMS-induced effects i.e. group differences for absolute changes on VAT volume (p=.097). Due to the low application volume, present WB-EMS protocols might not be the perfect tool for decreasing VAT in overweight to obese adults.

Neuromonitoring of the efferent nerve impulses transmission in the spinal cord tracts during surgical scoliosis treatment makes it possible to assess whether the functional status is deteriorating, affecting the procedure's safety. Is there any relationship between pre- and intraoperative motor evoked potentials recordings and does idiopathic scoliosis (IS) surgical correction improve directly the spinal efferent transmission? This study aimed to compare the results of surface recorded electromyography (EMG), electroneurography (ENG, M and F-waves), and especially motor evoked potentials (MEP) from tibialis anterior (TA) muscle bilaterally in 353 girls with the right idiopathic scoliosis (types 1A-4C according to Lenke classification). It has not yet been documented whether the results of MEPs recordings induced by transcranial single magnetic stimulus (TMS, pre – and postoperatively) and trains of electrical stimuli (TES; intraoperatively in T0-before surgery, T1 – after pedicle screws implantation, T2 – after scoliosis curvature distraction and derotation following two rods implantation) can be compared for diagnostic verification of improvement of the spinal neural transmission. The study also attempted to determine whether the constant level of optimal anesthesia during the certain surgical steps of scoliosis treatment affects the parameters of MEPs recorded during neuromonitoring procedures. No neurological deficits have been observed postoperatively. Values of amplitudes but not latencies in MEPs recordings evoked with TMS in IS patients compared before and after surgery indicated a slight improvement in the efferent transmission of neural impulses within the fibers of the spinal tracts postoperatively. Results of all neurophysiological studies in IS patients were significantly asymmetrical and recorded worse on the concave side, suggesting greater neurological motor deficits at p=0.04. This asymmetry had been significantly reduced following IS surgery. The surgeries in IS patients brought significant improvement (p=0.04) in parameters of amplitudes of sEMG recordings, however reflecting still the consequences of the neurogenic injury of TA muscle motor units. ENG studies results indicated the symptoms of the axonal type injury in peroneal motor fibers improved only on the concave side at p=0.04 in parallel with the significant improvement of F-waves parameters, which suggests that surgeries might result in the lumbar ventral roots decompression. There were not detected significant differences in amplitudes or latencies of MEPs induced with TMS or TES comparing the parameters recorded preoperatively (one day before surgery) and intraoperatively in T0. The amplitudes of TES evoked MEPs increased gradually at p=0.04 in the subsequent periods (T1 and T2) of observation. The significant reduction of MEPs latency at p=0.05 was observed only at the end of the IS surgery. Studies on the possible connections between the level of anesthesia fluctuations and the required TMS stimulus strength, as well as the MEPs amplitude changes measured in T0-T2 revealed lack of relationships. It is not likely that they could be the factors influencing the efferent transmission in spinal pathways beside the surgical procedures. Considering that MEPs amplitude parameter reflects the number of axons excited from the motor cortex and transmitting the efferent impulses via spinal descending tracts in the white matter, pre- (TMS evoked) and intraoperative (TES evoked) recordings are reliable for evaluating the patient’s neurological status before and during surgical scoliosis correction procedures. The results of this study indicate an agreement between preoperative and early-intraoperative evaluations with these both diagnostic methods. An increase of MEPs amplitude parameters recorded on both sides after scoliosis surgery proves immediate improvement of the total efferent spinal cord transmission. Considering comparative pre- and postoperative sEMG and ENG recordings it can be concluded that surgeries might directly result in the additional lumbar ventral roots decompression. Our results of the tests on the possible variability of the anesthesia level on the parameters of intraoperative recorded MEPs show no clear relationships. We can conclude that MEPs parameters changes are determined by the surgery procedures during neuromonitoring, not the anesthesia conditions if they are kept stable, which influences a decrease in the number of false-positive neuromonitoring warnings. Further studies on a larger population of patients with long-lasting observation postoperatively are required to confirm the presented conclusions on the direct influences of scoliosis surgery on improvement of the motor function in patients with IS.

Alzheimer’s disease (AD) is an age-related neuropsychiatric disorder and a common cause of progressive dementia. Diltiazem (DTZ), the non-dihydropyridine benzothiazepine class of calcium channel blocker (CCB), used clinically in angina and other cardiovascular disorders have proven neurological benefits. In the present study, the neuroprotective anti-dementia effects of DTZ against intra-cerebroventricular-streptozotocin (ICV-STZ)-induced sporadic AD (SAD)-type rat model was investigated. ICV-STZ-induced cognitive impairments were measured by passive avoidance and Morris water maze tasks. Anti-oxidative enzyme status, pro-inflammatory markers, and amyloid-beta (Aβ) protein expression in rat brain tissues were measured by ELISA kits, Western blotting, and immunostaining techniques. Data revealed that ICV-STZ injection in rats significantly induced cognitive deficits and altered the levels of oxidative and pro-inflammatory markers (p &lt; 0.05 ~ p &lt; 0.001). Treatment with DTZ (10 mg/kg, 20 mg/kg, and 40 mg/kg. p.o.) daily for twenty-one days, 1 h before a single ICV-STZ (3 mg/kg) injection, significantly improved cognitive impairments, ameliorated the ICV-STZ-induced altered nitrite, pro-inflammatory cytokines (TNF-α, and IL-1β) and anti-oxidative enzyme levels (superoxide dismutase, lipid peroxidation, and glutathione). Further, DTZ restored the increased Aβ protein expression in ICV-STZ-induced brain tissue Considering the data obtained, DTZ exhibited a potential neuroprotective anti-dementia role in ICV-STZ-induced SAD-type conditions in rats and might be repurposed as a potential therapeutic agent in the treatment and management of AD and related dementia pathologies.

Intra-articular fractures are a major cause of post-traumatic osteoarthritis (PTOA). Despite adequate surgical treatment, the long-term risk for PTOA is high. Previous studies reported that joint injuries initiate an inflammatory cascade characterized by elevation of synovial pro-inflammatory cytokines, which can lead to cartilage degradation and PTOA development. This review summarizes the literature on the post-injury regulation of pro-inflammatory cytokines and the markers of cartilage destruction in patients suffering from intra-articular fractures. METHODS We searched Medline, Embase, and Cochrane databases (1960–February 2020) and included studies that were performed on human participants and included control groups. Two investigators assessed the quality of the included studies using Covidence and the Newcastle-Ottawa Scale. RESULTS Based on the surveyed literature, several synovial pro-inflammatory cytokines, including interleukin (IL)-1β, IL-2, IL-6, IL-8, IL-12p70, interferon-y, and tumor necrosis factor-α, were significantly elevated in patients suffering from intra-articular fractures compared to control. A simultaneous elevation of anti-inflammatory cytokines such as IL-10 and IL-1RA was also observed. In contrast, IL-13, CTX-II, and aggrecan concentrations did not differ significantly between the compared cohorts. CONCLUSIONS Overall, intra-articular fractures are associated with an increase in inflammation-related synovial cytokines. However, more standardized studies which focus on the ratio of pro- and anti-inflammatory cytokines at different time points are needed.

Total Hip Arthroplasty is one of the most successful surgery. However, due to the worldwide growing population life expectancy and the related incidence of age-dependent bone diseases, a growing number of cases of intra-operative fractures lead to revision surgery with high rates of morbidity and mortality. Surgeons choose the type of the implant, either cemented or cementless prosthesis, on the basis of the age, the quality of the bone and the general medical conditions of the patients. Generally, no quantitative measures are available to assess the intra-operative fracture risk. Consequently, the decision-making process is mainly based on medical operators’ expertise and qualitative information obtained by imaging. Motivated by this scenario, we here propose a mechanical-supported strategy to assist surgeons in their decisions, by giving intelligible maps of the risk fracture which take into account the interplay between actual strength distribution inside the bone tissue and its response to the forces exerted by the implant. To this end, we produce charts and patient-specific synthetic “traffic-light” indicators of fracture risk, by making use of ad hoc analytical solutions to predict the stress levels in the bone by means of CT-based mechanical and geometrical parameters of the patient. We felt that, if implemented in a friendly software or proposed as an app, the strategy could constitute a practical tool to help the medical decision-making process, in particular with respect to the choice of adopting cemented or cementless implant

This article is the third part of a scientific project under the general title "Geometrized vacuum physics based on the Algebra of Signatures". In the first two papers [1,2], the ideal (i.e., non-curved and immobile) local region of vacuum was studied and the foundations of the Algebra of Signatures were laid. This article considers the possibilities of describing the curved and moving state of the same vacuum region on the basis of the mathematical apparatus of the Algebra of Signatures. The reasons for the multilateral consideration of vacuum and twisting of intra-vacuum processes into spiral bundles are disclosed. The 4-tensor is introduced for two-sided and 16-sided consideration of the curvature of the local vacuum region. On the basis of kinematic models, the following assumptions were made: about the inert properties of vacuum layers; about the possibility of displacement of vacuum layers relative to each other at a speed significantly exceeding the speed of light; about the possibility of "rupture" of the local region of vacuum. The proposed kinematic models of the movement of vacuum layers can be a theoretical basis for the development of "zero" (i.e., vacuum) technologies.

Initially introduced almost thirty years ago for the express purpose of providing electronic warfare systems the capabilities to detect, characterize, and identify radar emitters, Specific Emitter Identification (SEI) has recently received a lot of attention within the research community as a physical layer technique for securing Internet of Things (IoT) deployments. This attention is due in large part to SEI’s demonstrated success in passively and uniquely identifying wireless emitters using traditional machine learning and the success of Deep Learning (DL) within the natural language processing and computer vision areas. SEI exploits distinct and unintentional features present within an emitter’s transmitted signals. The existence of these distinctive and unintentional features is attributed to slight manufacturing and assembly variations that exist within and between the components, sub-systems, and systems that comprise an emitter’s Radio Frequency (RF) front end. Although sufficient to facilitate SEI, these features do not hinder normal operations such as detection, channel estimation, timing, and demodulation. However, despite the plethora of SEI publications, it has remained largely a focus of academic endeavors that primarily focus on proof-of-concept demonstration and little to no use in operational networks for various reasons. The focus of this survey is a review of SEI publications from the perspective of its use as a practical, effective, and usable IoT security mechanism, thus we use IoT requirements and constraints (e.g., wireless standard, nature of their deployment) as a lens through which each reviewed paper is analyzed. Previous surveys have not taken such an approach and have only used IoT as motivation, a setting, or a context. In this survey, we consider operating conditions, SEI threats, SEI at scale, publicly available data sets, and SEI considerations that are dictated by the fact that it is to be employed by IoT devices or IoT infrastructure.

Highly-correlated electrons – electrons that engage in strong electron-electron interactions – have been observed in transition metal oxides and quantum dots and can create unusual material behavior that is difficult to model, such as switching between a low resistance metal state and a high resistance Mott insulator state. Tests of devices using a layer-by-layer deposition process for forming multilayer arrays of ferritin (a transition metal (iron) oxide storage protein) have been previously reported that indicate that highly-correlated electron transport is occurring, consistent with models of electron transport in quantum dots. This paper reports the results of the effect of various degrees of structural homogeneity on the electrical characteristics of these ferritin arrays, as well as demonstrating that these structures can provide a switching function associated with the circuit that they are contained within, consistent with the observed behavior of highly-correlated electrons.

The details of ac-conductivity measurements in a colloidal electrolyte cell with flat control gate electrodes are discussed. The use of impedance diagnostics in studies of transport phenomena in such systems requires caution in the definition of the thickness of the screening accumulation layers that appear along the metal-electrolyte interfaces. The value of this characteristic length λ0 critically depends on the volume fraction ϕ⊙ of colloidal particles in the bulk of electrolyte. Accounting for the dependence λ0(ϕ⊙) makes it possible to consistently explain the large discrepancy in the available experimental data regarding the influence of colloidal fraction on the effective conductivity of the colloidal suspension.

This brief review introduces some general properties of lower atmospheric motions that may be exploited by birds, linking historical findings and current knowledge from both observational and modeling perspectives. The relative importance of turbulent mixing resulting from wind shear and that from buoyant thermals is emphasized as well as the determinants of the geometry of the resulting vertical motions.

Copper indium gallium selenide (CIGS) is an inexpensive material that has the potential to dominate the next-generation photovoltaic (PV) industry. Here we detail computational investigation of CIGS solar cell with encouragement of adopting cuprous dioxide (Cu₂O) as a Hole Transport Layer (HTL) for efficient fabricated CIGS solar cells. Although Cu₂O as a HTL has been studied earlier for perovskite and other organic/inorganic solar cell yet no study has been detailed on potential application of Cu₂O for CIGS solar cells. With the proposed architecture, recombination losses are fairly reduced at the back contact and contribute to enhanced photo-current generation. With the introduction of Cu₂O, the overall cell efficiency is increased to 26.63%. The wide-band of Cu₂O pulls holes from the CIGS absorber which allows smoother extraction of holes with experiencing lesser resistance. Further, it was also inferred that, HTL also improves the quantum efficiency (QE) for photons with large wavelengths thus increases the cell operating spectrum.

This article is devoted to the issues of thermal softening of materials in the surface layer of forging tools. The research covers numerical modeling of the forging process, laboratory tests of tempering of nitrided layers and the analysis of tempering of the surface layer of tools in the actual forging process. Numerical modeling was supported by measuring the temperature inside the tools with a thermocouple inserted into the tool to measure the temperature as close to the surface as possible. The modeling results confirmed the possibility of tempering the die material. The results of laboratory tests made it possible to determine the influence of temperature on tempering at different surface layer depths. Numerical analysis and measurement of surface layer microhardness of tools revealed the destructive effect of temperature during forging on the tempering of the nitrided layer and on the material layers located deeper below the nitrided layer.

Electrochemical energy conversion and storage is key for the use of regenerative energies at large scale. A thorough understanding of the individual components, such as the ion conducting membrane and the electrode layers, can be obtained with scattering techniques on atomit to molecular length scales. The largely heterogeneous electrode layers of High-Temperature Polymer Electrolyte Fuel Cells are studied in this work with small- and wide-angle neutron scattering at the same time with the iMATERIA diffractometer at the spallation neutron source at J-PARC, opening a view on structural properties on atomic to mesoscopic length scales.

Mixing layer height (MLH) is a crucial parameter for air quality modelling that is still not routinely measured. Common methods for MLH determination use atmospheric profiles recorded by radiosonde but they suffer from course temporal resolution since balloon launching is only twice a day. Recently cheap ceilometers are gaining popularity in the retrieval of MLH diurnal evolution based on aerosol profiles. This study presents a comparison of a proprietary (Jenoptik) and a free available (STRAT) algorithms to retrieve MLH diurnal cycle. The comparison is accomplished in summer season over urban area and radiosonde data is used to estimate MLHs according to parcel, lapse rate, and Richardson methods (the last algorithm is used as a reference in the study) in addition. It was found that STRAT and Jenoptik give lower MLH than radiosonde with an underestimation of about 150m and 650m respectively. Additionally, STRAT showed reasonable performance in tracking of MLH diurnal evolution. Daily MLH maximum of about 2000m was found in the late afternoon (18-19 LT). In contrast, Jenoptik algorithm showed more weaknesses, mainly attributed to its real-time operation and independent processing of a single profile. At night and during morning transition period, both lidar-based methods showed difficulties as MLH was often in the ceilometer’s incomplete overlapping zone so residual or advected aerosol layers aloft were misleadingly reported as mixing layer (ML).

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Bioactive surface coatings have retained the attention of researchers and physicians due to their versatility and range of applications in orthopedics, particularly in infection prevention. Antibacterial metal nanoparticles (mNPs) are a promising therapeutic, with vast application opportunities on orthopedic implants. The current research aimed to construct a polyelectrolyte multilayer on a highly porous titanium implant using alternating thin film coatings of chitosan and alginate via the layer-by-layer (LbL) self-assembly technique, along with the incorporation of silver nanoparticles (AgNPs) or titanium dioxide nanoparticles (TiO2NPs), for antibacterial and osteoconductive activity. These mNPs were characterized for their physicochemical properties using quartz crystal microgravimetry with dissipation system, nanoparticle tracking analysis, scanning electron microscopy, and atomic force microscopy. Their cytotoxicity and osteogenic differentiation capabilities were assessed by AlamarBlue and alkaline phosphatase (ALP) activity assays, respectively. The antibiofilm efficacy of the mNPs tested against Staphylococcus aureus. The LbL polyelectrolyte coating was successfully applied to the porous titanium substrate. A dose-dependent relationship between nanoparticle concentration and ALP as well as antibacterial effects was observed. TiO2NP samples were also less cytotoxic than AgNP counterparts, although similarly antimicrobial. Together, these data serve as a proof-of-concept for a novel coating approach for orthopedic implants with antimicrobial and osteoconductive properties.

Membrane-based beverage dealcoholization is a successful process for producing low- and non-alcoholic beer and represents a fast-growing industry. Polyamide NF and RO membranes are commonly applied for this process. Polyelectrolyte multilayer (PEM) NF membranes are emerging as industrially relevant species and their unique properties (usually hollow fiber geometry, high and tunable selectivity, low fouling) underlines the importance of testing them in the food industry as well. To test PEM NF membranes for beer dealcoholization, at small pilot scale we dealcoholized filtered and unfiltered lager beer with the tightest available commercial polyelectrolyte multilayer NF membrane (NX Filtration dNF40), which has a MWCO=400Da which is quite high for these purposes. Dealcoholization is possible with a reasonable flux (10 LMH) at low pressures (5-8.6 bar) with a real extract loss of 16-18% and an alcohol passage of ~100%. Inorganic salt passage is high (which is typical for PEM NF membranes), which greatly affected beer flavor. During the dealcoholization process, the membrane underwent changes which substantially increased its salt rejection values (MgSO4 passage decreased 4-fold) while permeance loss was minimal (less than 10%). According to our sensory examination, the process yielded an acceptable flavored beer which could be greatly enhanced by the addition of the lost salts and glycerol.

This article describes in detail the numerical modeling of a CZTS (copper zinc tin sulfide) based kesterite solar cell. The Solar Cell Capacitance Simulator -one-dimension (SCAPS-1D) software was used to simulate MO/CZTS/CdS/ZnO/FTO structured solar cells. The parameters of different photovoltaic thin-film solar cells are estimated and analyzed using numerical modeling. The effects of various parameters on the performance of the photovoltaic cell and the conversion efficiency are discussed. Since the response of the solar cell is also contingent on its internal physical mechanism, J-V characteristic measures are insufficient to characterize the behavior of a device. Different features, as well as different potential conditions, must be considered for simulation, disregarding the belief in the modeling of a solar cell. With a conversion efficiency of 25.72%, a fill factor of 83.75%, a short-circuit current of 32.96436 mA/cm2 and an open-circuit voltage of 0.64V, promising optimized results have been achieved. The findings will be useful in determining the feasibility of fabricating high-efficiency CZTS-based photovoltaic cells. The efficiency of a CZTS-based experimental solar cell is also discussed. First, the effects of experimentally developed CZTS solar cells are simulated in the SCAPS-1D environment. The experimental results are then compared to the SCAPS-1D simulated results. The conversion efficiency of an optimized system increases after cell parameters are optimized. Using one-dimensional SCAPS-1D software, the effect of system parameters such as the thickness, acceptor and donor carrier concentration densities of absorber and electron transport layers, and the effect of temperature on the efficiency of CZTS-based photovoltaic cells is investigated. The proposed results will greatly assist engineers and researchers in determining the best method for optimizing solar cell efficiency, as well as in the development of efficient CZTS-based solar cells.

Background: Central serous chorioretinopathy (CSC) is a common macular condition characterized by detachment of the neuroretina and is a frequent cause of central vision loss in adults. Among the various therapeutic strategies, subthreshold microsecond pulsed laser (SML) treatment has become a useful option. Despite the suggested involvement of choroidal circulatory disturbances in CSC, effects of this treatment on macular microperfusion have not been fully evaluated yet. Herein, we report the impact of SML on retinal and choroidal microvascular flow using non-invasive optical coherence tomography (OCT) angiography (OCTA). Methods: In this study, CSC patients with persistent subretinal fluid (SRF) with or without secondary choroidal neovascularization (CNV) were included (referred to as pachychoroid neovasculopathy (PNV) group and CSC group, respectively). SML was conducted using a yellow (577 nm) laser with duty cycle of 10%, spot size of 200 µm and duration of 200 ms. Best corrected visual acuity (BCVA) as well as OCT and OCTA images were evaluated at baseline and 4 weeks after SML. OCTA parameters of interest included full retinal perfusion (FRP), choriocapillaris perfusion (CCP), Sattler’s layer perfusion (SLP), and Haller’s layer perfusion (HLP), which were evaluated longitudinally and compared to unaffected fellow eyes. Results: 27 affected eyes and 17 fellow eyes from 27 patients were included. Before treatment, central retinal thickness (CRT) and subfoveal choroidal thickness (SFCT) of affected eyes were significantly larger than in fellow eyes. Four weeks after SML, CRT decreased significantly, whereas perfusion parameters did not change. In subgroup analyses, the CSC group showed a significant decrease of SFCT, whereas the PNV group did not despite the decrease of CRT. Conclusion: Our results suggest that the SML may SFCT of CSC, but not of PNV patients at least within four weeks following treatment. This effect seems to be independent of the change in choroidal perfusion measured with OCTA.

Abstract: Interrupted-sampling repeater jamming (ISRJ) is a kind of intra-pulse coherent decep-tion jamming that can generate false target peaks in the range profile and interfere with the de-tection and tracking of real targets. In this paper, an anti-ISRJ method based on the intra-pulse orthogonal waveform is proposed, which can recognize common interference signals by com-paring sub-signal matched filtering results. For some special scenes where real targets cannot be directly differentiated from false targets, a new recognition method based on the energy discon-tinuity of the interference signal in the time domain is proposed in this paper. The method pro-posed in this paper can recognize real and false targets in all ISRJ modes without any prior in-formation, such as jammer parameters, with a small amount of calculation, which is suitable for actual radar systems. Simulation experiments using different interference parameters show that although this method has a 3dB loss of pulse compression gain, it can completely suppress dif-ferent kinds of ISRJ interference when the SNR before pulse compression is higher than -20dB, with 100 % target detection probability.

Repetitive nature of the ribosomal DNA (rDNA) gene makes the sequencing of hundreds copies of mammalian 45S rDNA (about 45-kb per copy) extremely difficult and its assembly is often excluded. Increasing evidence shows that 45S rDNA variations (copy number or single nucleotide), structural ribosomal RNA (rRNA) transcript variants, and non-structural rRNA transcripts (sense and anti-sense long noncoding rRNAs that include promoter rRNAs, and rRNA-derived fragments) play essential roles in mammalian development and diseases. Complete pictures of the hundreds copies of 45S rDNA and their rRNA transcripts require further innovation in sequencing techniques that include bioinformatics. The advancements in mammalian rDNA and rRNA sequencings and the discoveries of novel functions of the rDNA variants and rRNA transcripts are discussed here.

The accurate virus detection, strain discrimination, and source attribution of contaminated food items remains a persistent challenge because of the high mutation rates anticipated to occur in foodborne RNA viruses, such as Hepatitis A virus (HAV). This has led to predictions of the existence of more than one sequence variant between the hosts (inter-host) or within an individual host (intra-host). However, there have been no reports of intra-host variants from an infected single individual, and little is known about the accuracy of the single nucleotide variations (SNVs) calling with various methods. In this study, the presence and identity of viral SNVs, either between HAV clinical specimens or among a series of samples derived from HAV clone1-infected FRhK4 cells, were determined following analyses of nucleotide sequences generated using next-generation sequencing (NGS) and pyrosequencing methods. The results demonstrate the co-existence of inter- and intra-host variants both in the clinical specimens and the cultured samples. The discovery and confirmation of multi-viral RNAs in an infected individual is dependent on the strain discrimination at the SNV level, and critical for successful outbreak traceback and source attribution investigations. The detection of SNVs in a time series of HAV infected FRhK4 cells improved our understanding on the mutation dynamics determined probably by different selective pressures. Additionally, it demonstrated that NGS could potentially provide a valuable investigative approach toward SNV detection and identification for other RNA viruses.

We have suggested earlier a new sustainable method for permafrost thermal stabilization that combines passive screening of solar radiation and precipitation with active solar-powered cooling of the near-surface soil layer thus preventing heat penetration in depth. Feasibility of this method has been shown by calculations, but needed experimental proof. In this article, we are presenting the results of soil temperature measurements obtained at the experimental implementation of this method outside of the permafrost area which actually meant higher thermal loads than in Polar Regions. We have shown that near-surface soil layer is kept frozen during the whole summer, even at air temperatures exceeding +30°C. Therefore, the method has been experimentally proven to be capable of sustaining soil frozen even in more extreme conditions than expected in permafrost areas. In addition to usual building and structure thermal stabilization, the method could be used to prevent the development of thermokarst, gas emission craters, and landslides; greenhouse gases, chemical, and biological pollution from the upper thawing layers at least in the area of human activities; protection against coastal erosion; and permafrost restoration after wildfires. Using commercially widely available components, the technology can be scaled up for virtually any size objects.

The optimized design of catalyst layer (CL) plays a vital role to improve the performance of polymer electrolyte membrane fuel cells (PEMFCs). The need to improve transport and catalyst activity is especially important at low Pt loading, where local oxygen and ionic transport resistances decrease the performance due to an inevitable reduction of active catalyst sites. In this work, local oxygen and ionic transport are analyzed using direct numerical simulation on virtually reconstructed microstructures. Four morphologies are examined: (i) heterogeneous, (ii) uniform, (iii) uniform vertically-aligned, and (iv) meso-porous ionomer distributions. The results show that the local oxygen transport resistance can be significantly reduced, while maintaining good ionic conductivity, through the design of high porosity CLs (ε≃0.6−0.7) with low agglomerated ionomer morphologies. Ionomer coalescence into thick films can be effectively mitigated by increasing the uniformity of thin films and reducing the tortuosity of ionomer distribution (e.g., good ionomer interconnection in supports with a vertical arrangement). The local oxygen resistance can be further decreased by the use of blended ionomers with enhanced oxygen permeability and meso-porous ionomers with oxygen transport routes in both water and ionomer. In summary, achieving high performance at low Pt loading in next-generation CLs must be accomplished through a combination of high porosity, uniform and low tortuosity ionomer distribution, and oxygen transport through activated water.

The use of interleaving material with viscoelastic properties is one of the most effective solutions to improve the damping capacity of CFRP laminates. Improving composite damping without threatening mechanical performance is challenging and the use of nanomaterials should lead to the target. In this paper, the effect of a nanostructured interlayer based on Graphite Nanoplatelets (GNPs) on the damping capacity and fracture toughness of CFRP laminates has been investigated. High-content GNP/Epoxy (70wt/30wt) coating was sprayed on the surface of CF/Epoxy prepregs at two different areal weight (10 and 40 g/m2) and incorporated at the middle-plane of a CFRP laminate. The effect of the GNP areal weight on viscoelastic and the mechanical behaviour of the laminates was investigated. Coupons with low-areal weight GNP interlayer showed a 25% increase in damping capacity with a trivial reduction of the elastic modulus. Moreover, a reduction in interlaminar shear strength (ILSS) and fracture toughness (both mode I and mode II) was observed in the composites with GNPs interlayer. GNPs alignment and degree of compaction reached during process were found as key parameters on material performances. By increasing the areal weight a mitigation on the mechanical performances drop was achieved (-15%).

This work focused on the evaluation of some machine learning (ML) models and their application in e-health, using intermediate nodes within an Internet of Things (IoT) platform used for heartbeat anomaly detection. For the evaluation of ML models, a set of statistical validation metrics was selected. These metrics were applied in the training, testing and validation phases of the models. The results obtained can determine relevant factors for the selection of ML models, either based on the statistical and intrinsic efficiency of the ML models, or on their suitability to be implemented in intermediate nodes within an IoT platform. the more Lightweight models such as Simple Linear Regression, Logistic Regression, and K Nearest Neighbors, could easily operate in intermediate nodes, and they are models that require low processing and storage to work. In conclusion, the approach for intermediate nodes of Internet of Things platforms using cognitive networks decreases the processing cost in cloud computing and transfers it to the fog layer.

A better study of the postnatal retinal development is not only essential for the in-depth understanding of the nature of the vision system but also may provide insights for treatment developments of eye conditions, such as retinopathy of premature (ROP). To date, quantitative analysis of postnatal retinal development is primarily limited to endpoint histological examination. This study is to validate in vivo optical coherence tomography (OCT) for longitudinal monitoring of postnatal retinal development in developing mouse eyes. Three-dimensional (3D) frame registration and super averaging were adopted to investigate the fine structure of the retina. Interestingly, a hyporeflective layer (HRL) between the nerve fiber layer (NFL) and inner plexiform layer (IPL) was observed in developing eyes and gradually disappeared with aging. To interpret the observed retinal layer kinetics, a model based on eyeball expansion, cell apoptosis, and retinal structural modification was proposed.

In this paper, a further mathematical analysis of some previous results of the author’s ongoing investigation regarding Prandtl’s equations is accomplished. In particular, the objective of the present work is the performance of an approximate explicit solution to Prandtl’s system of equations for a laminar, isothermal, incompressible and steady boundary layer flow of a Newtonian fluid, over an infinite horizontal flat plate.

The deterioration of soil-cement in corrosive environment leads to the reduction of strength and the increase of permeability. Effective methods of determining deteriorated layer permeability coefficient of soil-cement are currently lacking. A laboratory test method for permeability coefficient of deteriorated layer was proposed using the modified permeability coefficient testing apparatus. According to the proposed method, the permeability coefficient of deteriorated layer can be obtained after testing the permeability coefficient of the soil-cement specimen in curing room and the equivalent permeability coefficient and deterioration depth of the soil-cement specimen in corrosion environment. Taking the marine dredger fill of Jiaozhou Bay for example, the deteriorated layer permeability coefficients of soil-cements with different cement contents were tested. It turned out that the permeability of deteriorated layer increases with the increase of age. At the beginning of curing age, larger cement content leads to smaller permeability coefficient of the deteriorated layer of soil-cement. As the curing age increases, the deteriorated layer permeability coefficient of the soil-cement with larger cement content becomes larger. The evolution of the permeability coefficient of deteriorated layer with age can be formulated as the Logistic function. This study provides a support for anti-permeability designs of soil-cement structures in corrosive environment.

Suppressing the charge recombination at the interface of photoanode/electrolyte is the crucial way to enhance the photovoltaic performance of quantum dot sensitized solar cells (QDSSCs). In this scenario, ZnS/SiO2 blocking layer was deposited on TiO2/CuInS2 QDs to inhibit the charge recombination at photoanode/electrolyte interface. As a result, the TiO2/CuInS2/ZnS/SiO2 based QDSSCs delivers a power conversion efficiency (η) value of 4.63%, which is significantly higher than the 2.15% and 3.23% observed for QDSSCs with a TiO2/CuInS2 device and TiO2/CuInS2/ZnS, respectively. Electrochemical impedance spectroscopy and open circuit voltage decay analyses indicate that ZnS/SiO2 passivation layer on TiO2/CuInS2 suppress the charge recombination at the photoanode/electrolyte interface and prolongs the electron lifetime.

Ventilation in cities is crucial for the well being of their inhabitants. Therefore, local governments require air ventilation assessments (AVAs) prior to the construction of new buildings. In a standard AVA, however, only neutral stratification is considered, although diabatic and particularly unstable conditions may be observed more frequently in nature. The results presented here indicate significant changes in ventilation within most of the area of Kowloon City, Hong Kong, included in the study. A new definition for calculating ventilation was introduced, and used to compare the influence of buildings on ventilation under conditions of neutral and unstable stratification. The overall ventilation increased due to enhanced vertical mixing. In the vicinity of exposed buildings, however, ventilation was weaker for unstable stratification than for neutral stratification. The influence on ventilation by building parameters, such as the plan area index, was altered when unstable stratification was considered. Consequently, differences in stratification were shown to have marked effects on ventilation estimates, which should be taken into consideration in future AVAs.

Facial expression recognition is crucial for understanding human emotions and nonverbal communication. With the growing prevalence of facial recognition technology and its various applications, accurate and efficient facial expression recognition has become a significant research area. However, most previous methods have focused on designing unique deep-learning architectures while overlooking the loss function. This study presents a new loss function that allows simultaneous consideration of inter- and intra-class variations to be applied to CNN architecture for facial expression recognition. More concretely, this loss function reduces the intra-class variations by minimizing the distances between the deep features and their corresponding class centers. It also increases the inter-class variations by maximizing the distances between deep features and their non-corresponding class centers, and the distances between different class centers. Numerical results from several benchmark facial expression databases, such as Cohn-Kanade Plus, Oulu-Casia, MMI, and FER2013, are provided to prove the capability of the proposed loss function compared with existing ones.

Nowadays, frameworks and models are critical to enabling organizations to identify their current sustainability integration into business and to follow up on these initiatives over time. In this context, the maturity models offer a structured way of analyzing how a supply chain meets specific sustainability requirements and which areas demand attention to reach maturity levels. This study proposes a five-level maturity model to help supply chains identify their level of engagement with sustainability practices combining three perspectives: intra and inter-organizational sustainability practices, triple-bottom-line approach and critical areas for sustainability. All the steps followed in constructing the maturity model were based on a literature review, and case studies supported its improvement, application, and testing. The proposed model presents many advantages, such as being used as a self-assessment tool, a roadmap for sustainability behaviour improvement, and a benchmarking tool to evaluate and compare standards and best practices among organizations and supply chains.

Section 25(2) of the Constitution of South Africa protects property rights and the White Paper on Land Reform demonstrate tolerance and wisdom in the application of land reform policies. The central argument to this research was whether amendment of Section 25 (2) of the constitution to allow expropriation of land without compensation redresses redistribution of land for social cohesion and political stability. The researcher argues that, currently, Section 25 of the constitution provides for expropriation without compensation but at the same time protects property rights reducing the pace of redistribution. Hence, an amendment of section 25 (2) may remove the property right clause and accelerate expropriation without compensation. But whether the removal of the property right clause and acceleration of the process of expropriation without compensation will result to equitable and fair distribution of land to the majority of landless South Africans is not certain. The study concludes that, amendment of Section 25(2) is a justifiable process and priorities must be given to equity in redistribution to the majority landless at the margins of communities and not elites. If the amendment of Section 25 (2) cannot guarantee equity in redistribution for all ill respective of race, social cohesion, political stability and economic growth, intra-racial tensions may emerge. Such tensions may further compound the land question and affects investors’ confidence in South Africa.

1) Introduction: Negative pressure wound therapy (NPWT) is a frequently applied open abdomen (OA) treatment. There are only a few experimental data supporting this method and describing the optimal settings and pressure distribution in the abdominal cavity during this procedure. The aim of our study was to evaluate pressure values at different points of the abdominal cavity during NPWT in experimental abdominal compartment syndrome (ACS) animal model. 2) Methods: In this study (permission Nr. 13/2014/UDCAR) 27 Hungahib pigs (15.4- 20.2 kg) were operated. ACS was generated by implanting a plastic bag in the abdomen through mini-laparotomy and filled with 2100- 3300 ml saline solution (37 C°) to an intraabdominal pressure (IAP) of 30 mmHg. After 3 hours, NPWT (Vivano Med ® Abdominal Kit, Paul Hartmann AG, Germany) or Bogota bag was applied. NPWT group was divided into -50, -100 and 150 mmHg suction group. Pressure distribution to the abdominal cavity was monitored at 6 different points of the abdomen via a multichannel pressure monitoring system. 3) Results: The absolute pressure levels were significantly higher above than below the layer. The values of the pressure were similar in the midline than laterally. Amongst the bowels, the pressure values changed periodically between 0 and -12 mmHg which might be caused by the peristaltic movements. 4) Conclusions: The porcine model of the present study seems to be well applicable for investigating ACS and NPWT. It was possible to provide valuable for clinicians. The pressure was well distributed by the protective layer to the lateral parts of the abdomen and this phenomenon did not change considerably during the therapy.

Given the recent advances in information technology, speed has become an important requirement in data transmission. Given that an LED (light emitting diode) can turn on and off several thousand or even millions of times per second, then LiFi (light fidelity) technology has strong advantages over WiFi (wireless fidelity) in terms of speed. In this research project, a consortium involving an academic institution decided to evaluate the maturity of LiFi technology and design a demonstrator that could be integrated in a vehicle via an intra-vehicle data transmission system. The demonstrator is to implement a two-way LiFi communication between the reading light of a vehicle and a portable device such as a tablet or smartphone. The nomadic device must display, via an interface, data in real time. The data is RNT (Digital Terrestrial Radio) and TNT (Digital Terrestrial Television) provided by an in-house antenna. LiFi depends on optical technology. The optical characteristics have significant influences on the system. The paper shows ways to improve the system’s throughput, communication range, and reception area. By replacing the reading light with a more powerful one with better optical characteristics, the communication range and reception area improve. By using symmetrical power supply, the throughput improves. Likewise, by using optical filters that eliminate noise, the throughput also improves. We have demonstrated that LiFi data transmission in the vehicle is feasible; low-definition videos were successfully transmitted. The paper acknowledges that there are still various avenues for this work’s improvement.

The successive waves of the Covid-19 pandemic are driven by SARS-CoV-2 variants that reached critical detection levels in different parts of the world. But how evolved the Wuhan virus since its detection in December 2019 into the Alpha (B.1.1.7), Beta (B.1.351), Gamma (P.1), Delta (B.1.617.2) and Omicron (B.1.1.529) variants of concern? This is a story of mice and men, of up to 1,000,000 infected cells in one person, where each cell produces between 10⁵ and 10⁶ viral RNAs, of immune-compromised patients, the digestive tract and viral recombination.

(1) Background: The purpose of this study is to evaluate the full arch scan accuracy (precision and trueness) of nine digital intra-oral scanners and four lab scanners. Previous studies have compared the accuracy of some intra-oral scanners, but as this is a field of quickly developing technologies, a more up-to-date study was needed to assess the capabilities of currently available models.; (2) Methods: The present in vitro study compared nine different intraoral scanners (Omnicam 4.6; Omnicam 5.1; Primescan; CS 3600; Trios 3; Trios 4; Runyes; i500 and DL206) as well as four lab light scanners (Einscan SE; 300e; E2 and Ineos X5) to investigate the accuracy of each scanner by examining the overall trueness and precision. Ten aligned and cut scans from each of the intra-oral and lab scanners in the in vitro study were brought into CloudCompare. A comparison was made with the master STL using the CloudCompare 3D analysis best-fit algorithm. The results were recorded along with individual standard deviation and a colorimetric map of the deviation across the surface of the STL mesh; a comparison was made to the master STL, quantified at specific points. ; (3) Results: In the present study, the Primescan had the best overall trueness (17.3 ± 4.9). Followed by (in order of increasing deviation) the Trios 4 (20.8 ± 6.2), i500 (25.2 ± 7.3), CS3600 (26.9 ± 15.9), Trios 3 (27.7 ± 6.8), Runyes (47.2 ± 5.4), Omnicam 5.1 (55.1 ± 9.5), Omnicam 4.6 (57.5 ± 3.2) and Launca DL206 (58.5 ± 22.0). Regarding the lab light scanners, the Ineos X5 had the best overall trueness with (0.0 ± 1.9). Followed by (in order of increasing deviation) the 3Shape E2 (3.6 ± 2.2), Up3D 300E (12.8 ± 2.7), and Einscan SE (14.9 ± 9.5); (4) Conclusions: This study confirms that all current generations of intra-oral digital scanners can capture a reliable, reproducible full arch scan in dentate patients. Out of the intra-oral scanners tested, no scanner produced results significantly similar in trueness to the Ineos X5. However, the Primescan was the only one to be statistically of a similar level of trueness to the 3Shape E2 lab scanner. All scanners in the study had mean trueness of under 60-micron deviation. While this study can compare the scanning accuracy of this sample in a dentate arch, the scanning of a fully edentulous arch is more challenging. The accuracy of these scanners in edentulous cases should be examined in further studies.

New TLC-densitometric method have been developed for the identification and quantification of paracetamol (PA), propyphenazone (PP) and caffeine (C) of Saridon tablets using the NP-TLC technique combined with densitometry. This method allows for the simultaneous determination of PA, PP, and C in the same sample. Among all tested chromatographic conditions, the mixture consisting of chloroform + toluene + ethyl acetate + ethanol + acetic acid (18:18:7.5:5.0:0.3, v/v) and silica gel 60F254 plate proved to be the most effective for the separation of three tested active pharmaceutical ingredients (APIs) and substances related to paracetamol. The fully validation of the proposed NP-TLC method proves that it is specific, precise, accurate, robust and sensitive. The percentage content in relation to the content declared by the manufacturer is for propyphenazone 99.8%, paracetamol 101.6% and caffeine 100.8%, which are in accordance with pharmacopoeial requirements. The results presented indicate the possibility of using the developed method in the routine control of pharmaceutical preparations containing these APIs. The proposed method is economical and more sensitive compared to the previously proposed planar methods for the simultaneously determination of PA, PP and CAPIs. Will be an What is more, the presented method may be anaxcellent excellent economical alternative when HPLC method is unavailable for such determination.

With increasing demand from unmanned driving and robotics, more attention has been paid to point cloud-based 3D object accurate detection technology. However, due to the sparseness and irregularity of the point cloud, the most critical problem is how to utilize the relevant features more efficiently. In this paper, we proposed a point-based object detection enhancement network to improve the detection accuracy in the 3D scenes understanding based on the distance features. Firstly, the distance features are extracted from the raw point sets and fused with the raw features about reflectivity of the point cloud to maximizing the use of information in point cloud. Secondly, we enhanced the distance features and raw features that we collectively refer to them as self-features of the key points in Set Abstraction (SA) layers with the self-attention mechanism, so that the foreground points can be better distinguished from the background points. Finally, we revised the group aggregation module in SA layers to enhance the feature aggregation effect of key points. We conducted experiments on the KITTI dataset and nuScenes dataset and the results show the enhancement method proposed in this paper has excellent performance.

Several chemistry-climate models (CCM) underestimate the total column ozone (TCO) over the polar region in the Southern Hemisphere during wintertime. To evaluate potential causes of the problem, we exploit CCM SOCOLv3 to study the TCO over Antarctica sensitivity to the: (1) photo-dissociation rates of ozone for large solar zenith angles; (2) rates of the stratospheric heterogeneous reactions, and (3) intensity of the meridional flux into the polar regions due to sub-grid scale mixing processes in the model. Comparisons of the model results with the satellite-based IASI (Infrared Atmospheric Sounder Interferometer) sensor measurements showed that the most important processes for the improvement of the polar ozone simulation results are photolysis and horizontal mixing. The reasonable tuning of these factors has allowed us to improve the model representation of the ozone annual cycle over the southern polar region. The proposed increase of the horizontal mixing can be recommended for the CCMs with relatively low horizontal resolution.

In permafrost regions, ground surface deformations induced by freezing and thawing threaten the integrity of the built environment. Mapping the frost susceptibility of the ground at a high spatial resolution is of practical importance for the construction and planning sectors. We processed Sentinel-1 Interferometric Synthetic Aperture Radar (InSAR) data from thawing seasons 2015 to 2019, acquired over the area of Ilulissat, West Greenland. We used a least-squares inversion scheme to retrieve the average seasonal displacement (S) and long-term deformation rate (R). We secondly investigated two different methods to extrapolate active layer thickness (ALT) measurements, based on their statistical relationship with remotely-sensed surface characteristics. A Generalized Linear Model (GLM) was first implemented, but the model was not able to fit the data and represent the ALT spatial variability over the entire study domain. ALT were alternatively averaged per vegetation class, using a land cover map derived by supervised classification of Sentinel-2 images. We finally estimated the active layer ice content and used it as a proxy to map the frost susceptibility of the ground at the community scale. Fine-grained sedimentary basins in Ilulissat were typically frost susceptible and subject to average seasonal downward displacements of 3 to 8 cm. Areas following a subsiding trend of up to 2.6 cm/yr were likely affected by permafrost degradation and melting of ground ice below the permafrost table. Our approach enabled us to identify frost-susceptible areas subject to severe seasonal deformations, and/or long-term subsidence induced by degrading permafrost. Used in combination with traditional site investigations, InSAR maps provide valuable information for risk management and community planning in the Arctic.

Herein we foremost detailed the numerical modeling of the double absorber layer- methyl ammonium lead iodide– carbon nitride layer solar cell and subsequently provided in-depth insight on the active layer associated with dominant radiative and non-radiative recombination losses limiting the efficiency ( ) of the solar cell. Under recombination kinetics phenomena, we explored the influence of Radiative recombination, Auger recombination, Shockley Read Hall recombination, the energy distribution of defects; Band Tail recombination (Hoping Model), Gaussian distribution, metastable defect states including single donor (0/+), single acceptor (-/0), Double Donor (0/+/2+), double acceptor (2/-/0-), and the interface layer defects on the output characteristics of the solar cell. Setting defect (or trap) density to with uniform energy distribution of defects for all the layers, we achieved the of 24. 16 %. A considerable enhancement in power conversion efficiency was perceived as we reduced the trap density to for the absorber layers. Further, it was observed that for the absorber layer with double donor defect states, the active layer should be carefully synthesized to reduce crystal order defects to keep the total defect density as low as to achieve efficient device characteristics

An explanation of aerodynamic lift still is under controversial discussion as can be seen, for example, in a recent published article in Scientific American [1]. In contrast to an approach via integral conservation laws we here review an approach via the classical Kutta-Condition and its relation to boundary layer theory. Thereby we summarize known results for viscous correction to the lift coefficient for thin aerodynamic profiles and try to remember the work on triple-deck or higher order Boundary Layer theory, its connection to interactive boundary layer theory, viscous/inviscid coupling as implemented to well-known engineering code Xfoil. Finally we compare its findings to simple 2D numerical solution of full Navier Stokes equations (CFD)models. As a conclusion, a clearer definition of terms like understanding and explanation applied to the phenomenon of aerodynamic lift will be given.

During the long-term operation of the plasma reactor, decreases in the plasma concentration were noticed despite the constant maintenance of all parameters. One of the factors is the decrease of the nitrogen content on the surface of the electrode, in order to eliminate it, the supply voltage has been increased to 11 kV. The next decisive factor in the decrease of plasma concentration is the oxidation of the electrode surface, therefore two electrodes were used: first one with solid gold and the other one copper covered with galvanized gold with a thickness of 10 μm. During the experiment, a large decrease in plasma concentration was observed when the electrode coated by gold was used. High-energy electrons have knocked out the gold atoms from the electrode, as a result of which the gold evaporated and the raids layers formed. After a month of working of the electrodes, metallographic researches were carried out, the results of which are described in this publication.

Knowledge about laminar-turbulent transition on operating multi-megawatt wind turbine blades needs sophisticated equipment like hot-films or microphone arrays. Contrarily thermographic pictures can easily be taken from the ground and temperature differences indicate different states of the boundary layer. The accuracy however, still is an open question, so that an aerodynamic glove known from experimental research on aero-planes was used to classify the boundary-layer state of a 2 megawatt wind turbine blade operating in the orthern part of Schleswig-Holstein, Germany. State-of-the-art equipment for measurering static surface pressure was used for monitoring the lift distribution. To distinguish laminar and turbulent parts of the boundary layer (suction side only) 48 microphones were applied together with ground-based thermographic cameras from two teams. Additionally, an optical camera mounted on the hub was used to survey vibrations. During start-up (from 0 to 9 rpm) extended, but irregularly shaped regions of a laminar boundary layer were observed which had the same extension measured both with microphones and Thermography. When an approximately constant rotor rotation (9 rpm corresponding to approximately 6 m/s wind-speed) was achieved, a flow transition was visible at the expected position of 40 % chord length on the rotor blade, which was fouled with dense turbulent wedges and an almost complete turbulent state on the glove was detected. In all observations, quantitative determination of the flow transition positions from thermography and microphones agree well within their accuracy.

Carburizing of stainless steels at low temperatures (below 500°C) develops a high content carbon layer, known for its high hardness. X-ray Diffraction investigation indicates that carburization treatment does not impact the structure of substrate; however, introduced carbon causes expansion in the carburized layer through the increase in d-spacing. Characterization of carbon concentration and hardness profiles indicate that carbon content gradually decreases while moving further into the substrate; and the origin of the increased hardness of the expanded layer arises from the super-saturated carbon content, following the solid solution strengthening theory. An area that is not well understood is in regard to the carburized layer’s relation to the substrate and the significance in their differences. Using two grades of stainless steel, AISI 316L and PH 17-4, it was observed that the carburized layer is not a separate layer, but a higher carbon content version of the substrate,

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

Abstract: Intra-abdominal abscesses (IAA) may commonly arise following complicated gastrointestinal tract infections and, on occasion, from infections within the urinary system. Many of these IAA are initiated as a consequence of post-surgical complications. These abscesses have a substantial risk of morbidity and mortality. As a result, it is crucial to diagnose and treat them promptly to minimise these adverse outcomes. Therefore, radiological modalities play a vital role in diagnosing, localising, and detecting associated complications of IAA, as sometimes other investigations could be less reliable and non-specific. Radiological modalities are pivotal in achieving an accurate diagnosis, localising the abscesses, and identifying associated complications. This is especially important since alternative investigative methods may be misleading in certain situations. Radiological techniques such as ultrasound scans (USS), contrast-enhanced computed tomography (CECT), and even magnetic resonance imaging (MRI) are immensely helpful in diagnosing these conditions. These imaging tools guide clinicians in determining the most appropriate patient management strategies. In this article, we compile a case series involving tubo-ovarian abscess, appendicular abscess, diverticular abscess and infected walled-off pancreatic necrosis, paying particular attention to radiological features in the diagnosis. Furthermore, we reviewed the existing literature to delineate characteristic radiological features related to the cases we discussed.

Aims: To report on the clinico-pathological features of a series of 12 intra-oral mucoepidermoid carcinomas showing exclusive intra-cystic growth. Methods and methods: All mucoepidermoid carcinomas diagnosed in the period 1990-2012 were retrieved, the original histological preparations were reviewed to confirm the diagnosis, and from selected cases, showing exclusive intra-cystic neoplastic component, additional sections were cut at 3 subsequent 200m intervals and stained with Hematoxylin-Eosin, PAS and Alcian Blue, to possibly identify tumor invasion of the adjacent tissues, which could have been overlooked in the original histological preparations. Also, pertinent findings collected from the clinical charts and follow-up data were analyzed. Results: We identified 14 intraoral mucoepidermoid carcinomas treated by conservative surgery and with a minimum follow up of 5 years. The neosplasm were located in the hard palate (9 cases), the soft palate (2), the cheeck (2) and the retromolar trigone (1). In all instances histological examination was revealed the presence of a single cystic space, containing clusters of columnar, intermediate, epidermoid, clear and mucous-producing cells, the latter exhibiting distinct intra-cytoplasmic mucin production, as confirmed by PAS and Alcian Blue stains. The cysts were entirely circumscribed by fibrous connective tissue and no solid areas or infiltrating tumour clusters were detected. Conservative surgical resection was performed in all cases and no recurrences or nodal metastases were observed during the follow up period. Conclusions: Mucoepidermoid carcinomas showing prominent (>20%) intra-cystic proliferation currently are considered low-grade tumours. In addition, we also unveil the possibility that mucoepidermoid carcinomas, at least in their early growth phase, may display an exclusive intra-cystic fashion and might be considered as in situ carcinomas, unable to infiltrate adjacent tissues or metastasize.

Abstract: Current models in design of urban water management systems and their corresponding infrastructure using centralized designs have commonly failed from the perspective of cost effectiveness and inability to adapt to the future changes. These challenges are driving cities towards using decentralized systems. While there is great consensus on the benefits of decentralization; currently no methods exist which guide decision-makers to define the optimal boundaries of decentralized water systems. A new clustering methodology and tool to decentralize water supply systems (WSS) into small and adaptable units is presented. The tool includes two major components: (i) minimization of the distance from source to consumer by assigning demand to the closest water source, and (ii) maximization of the intra-cluster homogeneity by defining the cluster boundaries such that the variation in population density, land use, socio-economic level, and topography within the cluster is minimized. The methodology and tool are applied to Arua Town in Uganda. Four random cluster scenarios and a centralized system were created and compared with the optimal clustered WSS. It was observed that the operational cost of the four cluster scenarios is up to 13.9 % higher than the optimal, and the centralized system is 26.6% higher than the optimal clustered WSS, consequently verifying the efficacy of the proposed method to determine an optimal cluster boundary for WSS. In addition, optimal homogeneous clusters improve efficiency by encouraging reuse of wastewater and stormwater within a cluster and by minimizing leakage through reduced pressure variations.

An increased demand for natural products nowadays most specifically probiotics (PRO) is evident since it comes in conjunction with beneficial health effects for the consumers. In this regard, it is well known that encapsulation could affect positively the PRO's viability throughout food manufacturing and long-term storage. This paper aims to analyze and review various multilayer strategies for encapsulation of PRO. Double-layer encapsulation of PRO by electro-hydrodynamic atomization or electrospray technology has been reported along with layer-by-layer assembly and water-in-oil-in-water (W1/O/W2) double emulsions to produce multilayer PRO-loaded carriers. Finally, their applications in food products are presented. The resistance (cover material) and viability of (PRO) to mechanical damage, during gastrointestinal transit and shelf life of these trapping systems are also described. The PRO encapsulation in double and multiple-layer coatings combined with other technologies can be examined to increase the opportunities for new functional products with amended functionalities opening a novel horizon in food technology.

Opportunistic networks, an evolution of mobile Ad Hoc networks (MANETs), offer decentralized communication without relying on preinstalled infrastructure, enabling nodes to route packets through different mobile nodes dynamically. However, due to the absence of complete paths and rapidly changing connectivity, routing in opportunistic networks presents unique challenges. This paper proposes a novel probabilistic routing model for opportunistic networks, leveraging nodes' meeting probabilities to route packets towards their destinations. The model dynamically builds routes based on the likelihood of encountering the destination node, considering factors such as last meeting time and acknowledgment tables to manage network overload. Additionally, an efficient message detection scheme is introduced to alleviate high overhead by selectively deleting messages from buffers during congestion. Furthermore, the proposed model incorporates cross-layer optimization techniques, integrating optimization strategies across multiple protocol layers to maximize energy efficiency, adaptability, and message delivery reliability. Through extensive simulations, the effectiveness of the proposed model is demonstrated, showing improved message delivery probability while maintaining reasonable overhead and latency. This research contributes to the advancement of opportunistic networks, particularly in enhancing connectivity and efficiency for Internet of Things (IoT) applications deployed in challenging environments.

The ocean’s mixed layer depth (MLD) plays an important role in understanding climate dynamics, especially during extreme weather occurrences like hurricanes. This study investigates the effects of Hurricane Katrina (2005) on the MLD in the Gulf of Mexico, using the Delft3D modeling system. By integrating hydrodynamics and wave dynamics modules, we simulate the ocean’s response to extreme weather, focusing on temperature, salinity and MLD variations. Our analysis reveals significant cooling and mixing induced by Katrina, resulting in spatial and temporal fluctuations in temperature (~± 4°C) and salinity (~± 2.5 ppt). The MLD is estimated using a simple threshold method, revealing a substantial deepening to ~120 m on August 29th-30th during Hurricane Katrina in the middle of northern Gulf of Mexico, compared to an average MLD of ~20-40 m during pre-storm conditions. It took about 18-days to recover to ~84% of the pre-storm level after Katrina. Compared to the stand-alone FLOW model, the coupled FLOW+WAVE model yields a deeper MLD of ~5%. The MLD recovery and wave effect on the MLD provide insights from various scientific, environmental and operational perspectives, offering a valuable basis for ocean management, planning and applications, particularly during extreme weather events.

This paper proposes to combat active eavesdropping by intelligent reflecting surface (IRS) backscatter techniques. To be specific, the source (Alice) sends the confidential information to the intended user (Bob), while the eavesdropper (Willie) transmits jamming signal to interrupt the transmission for more data interception. To enhance the secrecy, an IRS is deployed and connected with Alice through fiber to transform the jamming signal into the confidential signal by employing backscatter techniques. Based on the considered model, an optimization problem is formulated to maximize signal-to-interference-plus-noise ratio (SINR) at Bob under the constraints of the transmit power at Alice, the reflection vector at the IRS and the allowable maximum SINR at Willie. To address the optimization problem, an alternate optimization algorithm is developed. The simulation results verify the achievable secrecy gain of the proposed scheme.

Electroluminescence (EL) is an innovative technology in the lighting area. The EL device's main structure consists of a phosphor layer sandwiched by two electrodes. In this work, several alternating current EL devices have been developed by applying a set of sequential layers with combinations of in-house prepared inks and commercially available ink as a phosphor layer. A flexible polyester textile substrate was functionalized with inks by spray coating technique, after knife-coated an interfacial layer directly on the surface. A thorough study was carried out on the phosphor layer composition to optimize the EL device performance, more precisely the illuminance intensity and the illuminance homogeneity. The developed phosphor layer was composed of zinc sulphide doped with copper (between 30.0 to 38.1 wt%) and diluted by using a diluent at different ratios (28.0 to 35.5 wt%). The best peak illuminance intensity of 61 lux was obtained when the phosphor ink presented 35.4% ZnS:Cu and was diluted with 33.0% diluent. The aim of this study to determine the best formulation of the phosphor layer, which can be highly promising for further developments of EL devices, taking in account different applications in market.

Wearing gloves while operating machinery in workshops is an essential precaution to prevent mechanical injuries and burns from high temperatures, among other potential hazards. Ensuring workers are properly equipped with gloves, which is a crucial measure in accident prevention. Glove images often occupy a minimal proportion of the frame and are easily obscured by cluttered backgrounds, especially with limited edge computing resources. Consequently, this study proposes a glove detection algorithm called YOLOv8-AFPN-M-C2f based on YOLOv8, offering swifter detection speeds, lower computational demands, and enhanced accuracy for workshop scenarios. This research innovates by substituting the head of YOLOv8 with the AFPN-M-C2f network, amplifying the pathways for feature vector propagation, and mitigating semantic discrepancies between non-adjacent feature layers. Additionally, the introduction of a superficial feature layer enriches surface feature information, augmenting the model's sensitivity to smaller objects. To assess the performance of the YOLOv8-AFPN-M-C2f model, we conducted multiple experiments using a factory glove detection dataset compiled for this study. The results indicate that the enhanced YOLOv8 model surpasses other network models. Compared to the baseline YOLOv8 model, the refined version shows a 2.6% increase in mAP@50%, a 90.1% rise in FPS, and a 13% reduction in the number of parameters. This research contributes an effective solution for the detection of glove adherence.

Calcium sulfate (CS) materials containing terbium ions at 0, 1.0, or 2.0 mol.% were obtained by mechanochemical synthesis. According to X-ray diffraction data, the powder materials are characterized by the presence of a CaSO4×0.5H2O phase, while Tb3+ is incorporated into the lattice at ≤1.0 mol.%. Specific surface area enlarged from 2.1 to 22.5 m2/g as crystallite size decreased from 68 to 31 nm and the Tb3+ concentration increased up to 1.0 mol.%. Thermal analysis showed that terbium slightly raises the temperature of CaSO4×2H2O-to-CaSO4 transition. The presence of Tb3+ did not affect the solubility of the CS cements. Furthermore, after 7 days of soaking of the materials in a simulated body fluid, a calcium phosphate layer formed corresponding to a hydroxyapatite phase, in contrast to the pure cements. Luminescent properties were studied by excitation at 276 nm. The recorded emission peaks of the CS materials indicated that the luminescence of the samples is green and blue, with the most intense luminescence observed for samples containing 1.0 mol.% Tb3+. The developed materials can find applications in medicine as bioimplants for the regeneration and restoration of bone tissue with a possibility of noninvasive monitoring of the bone restoration process.

This study focuses on the analyses of nano-twinned Copper (Cu) films deposited through magnetron sputtering on Silicon Carbide (SiC) chips. The investigation encompasses the utilization of Chromium (Cr) adhesive layer coupled with varying voltage bias conditions. The goal is to comprehensively examine the influence of adhesive layer and negative bias voltages, contributing to an enhanced understanding of materials engineering and bonding technologies for advanced applications. The formation of a nanotwinned structure and (111) surface orientation can be properly controlled by applied substrate bias. High density nanotwinned structures were introduced into Cu films sputtered on SiC substrates with 82.3% of (111)-orientation proportion at -150 V much higher than the Cu film sputtered with another substrate bias. It is concluded that the sputtered Cu nanotwinned film formed with -150 V bias voltage has the potential to be employed as the interlayer for low temperature direct bonding.

The flow around thick airfoils at low Reynolds numbers and the possibility of using energy methods to control flowfield, increase lift and reduce drag are considered. For calculations, a series of propulsion airfoils is used, obtained by a combination of solving the inverse problem of aerodynamics and stochastic methods of global optimization. The calculations take into account the transition from the laminar flow regime to the turbulent one, which has a significant effect on the lift and airfoil drag. The applicability of various turbulence models for airfoil modelling at low Reynolds numbers is discussed. The results of numerical simulation make it possible to determine the dependence of the lift coefficient on the angle of attack and the optimal flow rate of air taken from the airfoil surface for each angle of attack. The results of numerical simulation are compared with the data of a physical experiment, and conclusions are drawn about the accuracy of various turbulence models.

Nano- and micro-sized CeO2 surface layers based on titanium alloy TiAl6V4 were obtained by magnetron sputtering with or without subsequent annealing. The structure of the samples was determined using scanning electron microscopy, Auger electron spectroscopy, energy dispersive spectroscopy, and X-ray diffraction. Hardness was measured by sclerometry. A direct linear dependence of the thickness of the surface layers on the deposition time and an extreme dependence, passing through a maximum, on the power are shown. A decrease in hardness with an increase in the thickness of the cerium oxide coating was noted. An increase in surface roughness, delamination and loosening of the surface layer, presumably associated with annealing, were noted. In samples with a surface layer thinner than 715 nm without annealing and 750 nm after annealing, the formation of a sublayer of TiO2, Al2O3, and Ce(VO4) was found, and in annealed samples with a layer length of less than 300 nm, all cerium dioxide reacted with vanadium dioxide to form vanadate.

In the past decade, considerable efforts have been devoted to the development of semitransparent organic solar cells. Numerous materials and architectures have been proposed for the future commercialization of these devices. Among these, the use of ternary active layers demonstrated a great promise for the development of efficient semi-transparent organic solar cells with the potential for future applications including self-powered greenhouses and powered windows. Researchers seek alternative solutions to the trade-off between device power conversion efficiency (PCE) and average visible transmittance (AVT), with photoactive materials being the key parameters that govern both (PCE) and (AVT) as well as device stability. Several new organic materials, including polymers and small molecules, were synthesized, and used in conjunction with a variety of techniques to achieve semitransparent conditions. In this review paper, we will look at the working principle and key parameters of semi-transparent organic solar cells, as well as the methods that have been used to improve the performance of ternary-based semi-transparent organic solar cells. The main approaches were concluded to be spectral enhancement and transparency increment of the active layer through bandgap tuning, utilizing novel organic semiconductors, and design architecture of the active layers.

Graphene nanostructures (GNS) are among the most promising materials for creating supercapacitors. However, GNS are still not used in creating supercapacitors due to the impossibility of obtaining large volumes of high-quality material at an acceptable cost. In this work, we investigated the efficiency of using few-layer graphene (FLG) with the number of layers is not more than 5 synthesized under Self-propagating high-temperature synthesis (SHS) conditions as basic material for supercapacitors. Using the SHS process makes it possible to synthesize large volumes of FLG without Stone-Wales defects. It was found that the synthesized FLG makes it possible to obtain better results than using classical materials, namely activated carbon (AC). It was found that the sample based on FLG has a higher specific capacitance – 65 F×g-1 compared to the sample from AC, the specific capacitance of which is 35 F×g-1, for a speed of 5 mV×s-1 these values are 170 and 64 F×g-1, respectively. The drop in capacitance over 1000 cycles was 4%, which indicates a sufficiently high stability of FLG and allows us to consider FLG as perspective material for use in supercapacitors.