In this study, a graphene-doped porous silicon (G-doped/p-Si) substrate for low ppm H₂ gas detection by an inexpensive synthesis route was proposed as a potential noble graphene-based gas sensor material and to understand the sensing mechanism. The G-doped/p-Si gas sensor was synthesized by a simple capillary force-assisted solution dropping method on p-Si substrates, whose porosity was generated through an electrochemical etching process. G-doped/p-Si was fabricated with various graphene concentrations and exploited as a H₂ sensor operated at room temperature. The sensing mechanism of the sensor with/without graphene decoration on p-Si was proposed to elucidate the synergetic gas sensing effect generated from the interface between the graphene and p-type silicon.

We report a self-assembly synthesis of silicon nanoparticles/nitrogen-doped reduced graphene oxide/ carbon nanofiber (Si@N-doped rGO/CNF) composites as potential high-performance anodes for rechargeable lithium-ion batteries (LIB) through the electrostatic attraction between amino and carboxyl groups. Nitrogen atoms generate a large number of vacancies or defects on the graphite plane, providing additional transmission channels for the diffusion of lithium ions, and improving the conductivity of the electrode. Carbon nanofiber (CNF) can help maintain the stability of the electrode structure and prevent silicon nanoparticles from falling off the electrode, prevent silicon nanoparticles from being directly exposed to the electrolyte, and can form a stable solid electrolyte interface (SEI) film. The three-dimensional conductive structure composed of Si, nitrogen atom-doped reduced graphene oxide (N-doped rGO), and CNF can effectively buffer the volume changes of silicon nanoparticles, shorten the transmission distance of lithium ions (Li+) and electrons, and make the electrode have good conductivity and stability in mechanical properties. In addition, compared with the Si@N-doped rGO and Si/rGO/CNF composite electrode, the Si@N-doped rGO/CNF composite electrode shows good cycle performance and rate capability, and its reversible specific capacity can reach 1418.8 mAh/g. The capacity retention rate is 64.7%, and the coulomb efficiency is 95%.

Peptide nucleic acid (PNA) is a synthetic DNA mimic that outperforms the properties of traditional oligonucleotides (ONs). On account of its outstanding features, such as remarkable binding affinity towards complementary DNA or RNA as well as high thermal and chemical stability, PNA has been proposed as a valuable alternative to the ON probe in gene-sensor design. In this study, a hybrid transducer made-up of graphene oxide (GO) nano-sheets covalently grafted onto a porous silicon (PSi) matrix has been investigated for the early detection of a genetic cardiac disorder, the Brugada syndrome (BS). A functionalization strategy towards the realization of a potential PNA-based device is described. A peptide nucleic acid (PNA), able to detect the SCN5A associated with the BS has been properly synthesized and used as a bioprobe for the realization of a proof-of-concept label-free optical PNA-biosensor. PSi reflectance and GO photoluminescence (PL) signals were simultaneously exploited for the monitoring of the device functionalization and response.

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) are fa-vorable sensor materials because of their large surface area, ease of fabrication, and cost effec-tiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computa-tional simulations do not always match experimental results, and even experimental results re-ported by different researchers have not been consistent. In the present study, we explored the effects of metal decorations on LIG gas sensors, with NO2 and NH3 gases as representative oxi-dizing and reducing agents, respectively. To eliminate unwanted side effects arising from metal salt residues, metal NPs were directly deposited by vacuum evaporation. Although the gas sen-sitivities of the sensors deteriorate upon metal decoration irrespective of the metal work function in the case of NO2 gas, they improve upon metal decoration in the case of NH3 exposure. A careful investigation of the chemical structure and morphology of the metal NPs in the LIG sensors shows that the spontaneous oxidation of metal NPs with a low work function changes the be-havior of the LIG gas sensors and that the sensor behaviors under NO2 and NH3 gases follow different principles.

This study is dedicated to enhancing lithium battery performance through the utilization of porous conductive polyaniline-modified graphene composites (PMGC). Given the growing importance of green energy, coupled with the development of lithium-ion battery systems and electric vehicles, achieving high-speed charge and discharge performance has become imperative. Traditional approaches involve incorporating additives like carbon nanotubes and graphene into electrodes to improve conductivity, but they encounter challenges related to cost and aggregation issues. In this study, polyaniline (PANI), a cost-effective, stable, and conductive polymer, was explored. PMGC was formed by employing ammonium persulfate (APS) as an oxidant during PANI polymerization, simultaneously serving as a surface modifier for graphene. The study systematically investigated the impact of varying amounts of PMGC on lithium-ion battery electrodes, assessing reductions in internal resistance, aging effects, different charge and discharge rates, and cycle performance. PMGC exhibited a porous structure formed by nanoscale PANI intertwining on graphene. Various measurements, including FT-IR, TGA, Raman spectroscopy, and battery performance assessments, confirmed the successful synthesis and positive effects of PMGC. Results indicated that a 0.5% addition of PMGC led to reduced internal resistance and enhanced fast charging and discharge capacity. However, excessive PMGC adversely affected aging and self-discharge. The study provides valuable insights into optimizing PMGC content for improved lithium battery performance, presenting potential advancements in energy storage systems and electric vehicles.

Graphene-based nanomaterials have emerged as promising materials for a wide range of applications.. Therefore, in the last years carbon nanoparticles have attracted great attention due to their low toxicity, high biocompatibility and easy preparation. Recently, N-doped carbon nanoparticles have been shown to have improved antibacterial activity over the undoped nanomaterial, but it is difficult to find correlations between the structure of the nanoparticle and its antibacterial activity. With this purpose, here, we analyze the effect of both, the nanoparticle size and the surface chemical composition of four N-doped carbon nanoparticles on the growth of Escherichia coli bacteria. Our results were analyzed using a Ligand-Substrate model based on the Monod´s equation, which allows us to interpret the dependence of the nanoparticle-bacteria affinity with the nanomaterial structure.

Tackling global warming and the consequent climate change in our planet is of urgent importance to our society. Renewable biomass derived carbons have been studied as promising adsorbents, but marine biomass derived carbons have not been explored extensively. S and N double-doped porous carbons were obtained from a marine biomass related precursor. Adding carbon nanoparticles (CNP) graphene oxide (GO), or carbon nanotubes (CNTs), in an early stage of the synthesis leads to a modified porous texture and surface chemistry. The carbons retained 2-4.5 at% nitrogen and 1.1 at% sulfur. The best GO and CNT added carbons had an apparent surface area 1780 m2/g and 1170 m2/g, respectively, compared to 1070 m2/g of the CNP-free matrix. The Dubinin-Radushkevich (DR) and Henry models were used to assess the strength of the interactions between various gases and the surface. The N2/H2 and CO2/CH4 selectivities were estimated with ideal adsorbed solution theory (IAST). While the CNPs, particularly GO, had a remarkable effect both on the porous texture and the surface chemistry, their influence on selectivity is more modest.

We theoretically investigate and optimize four-wave mixing (FWM) in silicon nitride (SiN) waveguides integrated with two-dimensional (2D) layered graphene oxide (GO) films. Based on extensive previous measurements of the material parameters of the GO films, we perform detailed analysis for the influence of device parameters including waveguide geometry, GO film thickness, length, and coating position on the FWM conversion efficiency (CE) and conversion bandwidth (CB). The influence of dispersion and photo-thermal changes in the GO films is also discussed. Owing to the strong mode overlap between the SiN waveguides and the highly nonlinear GO films, FWM in the hybrid waveguides can be significantly enhanced. We obtain good agreement with previous experimental results and show that by optimizing the device parameters to balance the trade-off between Kerr nonlinearity and loss, the FWM CE can be improved by as much as ~20.7 dB and the FWM CB can be increased by ~4.4 folds, relative to the uncoated waveguides. These results highlight the significantly enhanced FWM performance that can be achieved in SiN waveguides by integrating 2D layered GO films.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

The Kerr nonlinear optical performance of silicon nanowire waveguides integrated with 2D layered graphene oxide (GO) films is theoretically studied and optimized based on experimentally measured linear and nonlinear optical parameters of the GO films. The strong mode overlap between the silicon nanowires and highly nonlinear GO films yields a significantly enhanced Kerr nonlinearity for the hybrid waveguides. A detailed analysis for the influence of waveguide geometry and GO film thickness on the propagation loss, nonlinear parameter, and nonlinear figure of merit (FOM) is performed. The results show that the effective nonlinear parameter and nonlinear FOM can be increased by up to ≈52 and ≈79 times relative to bare silicon nanowires, respectively. Self-phase modulation (SPM)-induced spectral broadening of optical pulses is used as a benchmark to evaluate the nonlinear performance, examining the trade-off between enhancing Kerr nonlinearity and minimizing loss. By optimizing the device parameters to balance this, a high spectral broadening factor of 27.6 can be achieved ‒ more than 6 times that achieved in previous experiments. Finally, the influence of pulse chirp, material anisotropy, and the interplay between saturable absorption and SPM is also discussed. These results provide useful guidance for optimizing the Kerr nonlinear optical performance of silicon waveguides integrated with 2D layered GO films.

Microwave absorbers with lightweight, good stability and high efficiency have attracted much attention for their applications in many contemporary fields. In this work, the 3D porous (Ni@NO-C)n/NO-C composite absorber was prepared by a wet chemistry method with Ni chains and melamine as precursors, in which NO-C (N,O-doped carbon) encapsulated Ni particles are homogenously dispersed in the 3D porous networks of NO-C in the form of (Ni@NO-C)n chains. The special microstructure of the as-prepared material is proved to be benefit for the improvement of its microwave adsorption performance. The as-synthesized (Ni@NO-C)n/NO-C composite ab-sorber exhibited an effective absorption bandwidth of 4.1 GHz and an extremely large reflection loss of -72.3 dB. The excellent microwave absorbing performances can be ascribed to the coopera-tive consequence of dielectric loss and magnetic loss along with the balance between attenuation capability and impedance match.

Layered two-dimensional (2D) GO films are integrated with silicon-on-insulator (SOI) nanowire waveguides to experimentally demonstrate an enhanced Kerr nonlinearity, observed through self-phase modulation (SPM). The GO films are integrated with SOI nanowires using a large-area, transfer-free, layer-by-layer coating method that yields precise control of the film thickness. The film placement and coating length are controlled by opening windows in the silica cladding of the SOI nanowires. Owing to the strong mode overlap between the SOI nanowires and the highly nonlinear GO films, the Kerr nonlinearity of the hybrid waveguides is significantly enhanced. Detailed SPM measurements using picosecond optical pulses show significant spectral broadening enhancement for SOI nanowires coated with 2.2-mm-long films of 1−3 layers of GO, and 0.4-mm-long films with 5−20 layers of GO. By fitting the experimental results with theory, the dependence of GO’s n₂ on layer number and pulse energy is obtained, showing interesting physical insights and trends of the layered GO films from 2D monolayers to quasi bulk-like behavior. Finally, we show that by coating SOI nanowires with GO films the effective nonlinear parameter of SOI nanowires is increased 16 fold, with the effective nonlinear figure of merit (FOM) increasing by about 20 times to FOM > 5. These results reveal the strong potential of using layered GO films to improve the Kerr nonlinear optical performance of silicon photonic devices.

Layered 2D graphene oxide (GO) films are integrated with silicon nitride (SiN) waveguides to experimentally demonstrate an enhanced Kerr nonlinearity via four-wave mixing (FWM). Owing to the strong light–matter interaction between the SiN waveguides and the highly nonlinear GO films, the FWM performance of the hybrid waveguides is significantly improved. SiN waveguides with both uniformly coated and patterned GO films are fabricated based on a transfer-free, layer-by-layer GO coating method together with standard photolithography and lift-off processes, yielding precise control of the film thickness, placement and coating length. Detailed FWM measurements are carried out for the fabricated devices with different numbers of GO layers and at different pump powers. By optimizing the trade-off between the nonlinearity and loss, we obtain a significant improvement in the FWM conversion efficiency of ≈7.3 dB for a uniformly coated device with 1 layer of GO and ≈9.1 dB for a patterned device with 5 layers of GO. We also obtain a significant increase in FWM bandwidth for the patterned devices. A detailed analysis of the influence of pattern length and position on the FWM performance is performed. Based on the FWM measurements, the dependence of GO’s third-order nonlinearity on layer number and pump power is also extracted, revealing interesting physical insights about the 2D layered GO films. Finally, we obtain an enhancement in the effective nonlinear parameter of the hybrid waveguides by over a factor of 100. These results verify the enhanced nonlinear optical performance of SiN waveguides achievable by incorporating 2D layered GO films.

Silicon-based photoelectrochemical (PEC) conversion system has recently gained attention with its ability to provide cost-efficient and superior photoresponsive behavior in regard to other various semiconductor photoelectrodes. Carbon-based co-catalysts have always shared the spotlight for being rendered as alternative metal-free electrocatalysts intended for hydrogen evolution reaction (HER). In particular, a representative carbon-derived material, reduced Graphene Oxide (rGO) has attracted much attention as a non-metal catalyst for efficient and durable HER. Herein, we have deposited rGO on silicon nanowire (SiNW) structure which shows the highest reduction in the overpotential for HER up to date. This could be attributed to the synergistic effects of rGO and SiNW with unique anisotropic morphology, facile tuning capabilities, and scalable fabrication methods. Combined with nanostructured photocathode, rGO deposited SiNW showed better applied bias photon to current conversion efficiency of 3.16%, which is 158 times higher than that of bare planar Si system. In regard to this development we believe that rGO-SiNW photoelectrodes would pave the way for state-of-the-art highly efficient non-metal catalysts for energy conversion technologies.

In recent years graphene has attracted much interest due to its unique properties of flexibility, strong light-matter interaction, high carrier mobility and broadband absorption. In addition, graphene can be deposited on many substrates including silicon with which is able to form Schottky junctions opening the path to the realization of near-infrared silicon photodetectors based on the internal photoemission effect where graphene play the role of the metal. In this work, we review the very recent progress of the near-infrared photodetectors based on Schottky junctions involving graphene. This new family of device promises to overcome the limitations of the Schottky photodetectors based on metals showing the potentialities to compare favorably with germanium photodetectors currently employed in silicon photonics.

We experimentally demonstrate enhanced self-phase modulation (SPM) in silicon nitride (Si₃N₄) waveguides integrated with 2D graphene oxide (GO) films. GO films are integrated onto Si₃N₄ waveguides using a solution-based, transfer-free coating method that enables precise control of the film thickness. Detailed SPM measurements are carried out using both picosecond and femtosecond optical pulses. Owing to the high Kerr nonlinearity of GO, the hybrid waveguides show significantly improved spectral broadening compared to the uncoated waveguide, achieving a broadening factor of up to ~3.4 for a device with 2 layers of GO. By fitting the experimental results with theory, we obtain an improvement in the waveguide nonlinear parameter by a factor of up to 18.4 and a Kerr coefficient (n₂) of GO that is about 5 orders of magnitude higher than Si₃N₄. Finally, we provide a theoretical analysis for the influence of GO film length, coating position, and its saturable absorption on the SPM performance. These results verify the effectiveness of on-chip integrating 2D GO films to enhance the nonlinear optical performance of Si₃N₄ devices.

The detection of dopamine in a highly sensitive and selective manner is crucial for the early diagnosis of a number of neurological diseases/disorders. Here, a report on a new platform for the electrochemical detection of dopamine with a considerable accuracy that comprises a 3D porous graphene oxide (pGO)/gold nanoparticle (GNP)/pGO composite-modified indium tin oxide (ITO) is presented. The pGO was first synthesized and purified by ultrasonication and centrifugation, and it was then further functionalized on the surface of a GNP-immobilized ITO electrode. Remarkably, owing to the synergistic effects of the pGO and GNPs, the 3D pGO-GNP-pGO-modified ITO electrode showed a superior dopamine-detection performance compared with the other pGO- or GNP-modified ITO electrodes. The linear range of the newly developed sensing platform is from 0.1 μM to 30 μM with a limit of detection (LOD) of 1.28 μM, which is more precise than the other previously reported GO-functionalized electrodes. Moreover, the 3D pGO-GNP-pGO-modified ITO electrodes maintained their detection capability even in the presence of several interfering molecules (e.g., ascorbic acid, glucose). The proposed platform of the 3D pGO-GNP-pGO-modified ITO electrode could therefore serve as a competent candidate for the development of a dopamine-sensing platform that is potentially applicable for the early diagnosis of various neurological diseases/disorders.

Optical parametric amplification (OPA) represents a powerful solution to achieve broadband amplification in wavelength ranges beyond the scope of conventional gain media, for generating high-power optical pulses, optical microcombs, entangled photon pairs and a wide range of other applications. Here, we demonstrate optical parametric amplifiers based on silicon nitride (Si₃N₄) waveguides integrated with two-dimensional (2D) layered graphene oxide (GO) films. We achieve precise control over the thickness, length, and position of the GO films using a transfer-free, layer-by-layer coating method combined with accurate window opening in the chip cladding using photolithography. Detailed OPA measurements with a pulsed pump for the fabricated devices with different GO film thicknesses and lengths show a maximum parametric gain of ~24.0 dB, representing a ~12.2 dB improvement relative to the device without GO. We perform a theoretical analysis of the device performance, achieving good agreement with experiment and showing that there is substantial room for further improvement. This work demonstrates a new way of achieving high photonic integrated OPA performance by incorporating 2D materials.

We experimentally demonstrate enhanced spectral broadening of femtosecond optical pulses after propagation through silicon-on-insulator (SOI) nanowire waveguides integrated with two-dimensional (2D) graphene oxide (GO) films. Owing to the strong mode overlap between the SOI nanowires and the GO films with a high Kerr nonlinearity, the self-phase modulation (SPM) process in the hybrid waveguides is significantly enhanced, resulting in greatly improved spectral broadening of the femtosecond optical pulses. A solution-based, transfer-free coating method is used to integrate GO films onto the SOI nanowires with precise control of the film thickness. Detailed SPM measurements using femtosecond optical pulses are carried out, achieving a broadening factor of up to ~4.3 for a device with 0.4-mm-long, 2 layers of GO. By fitting the experimental results with theory, we obtain an improvement in the waveguide nonlinear parameter by a factor of ~3.5 and the effective nonlinear figure of merit (FOM) by a factor of ~3.8, relative to the uncoated waveguide. Finally, we discuss the influence of GO film length on the spectral broadening and compare the nonlinear optical performance of different integrated waveguides coated with GO films. These results confirm the improved nonlinear optical performance for silicon devices integrated with 2D GO films.

In this study, a composite film was developed for electrochemical sensing of tryptophan (Trp). Porous reduced graphene oxide (PrGO) was utilized as the electron transfer layer, and a C-undecylcalix[4] resorcinarene Langmuir-Blodgett (CUCR-LB) film served as the molecular recognition layer. Atomic force microscopy (AFM), transmission electron microscopy (TEM), Raman spectroscopy, scanning electron microscopy (SEM), and electrochemical experiments were employed to analyze the characteristics of the CUCR-LB/PrGO composite film. The electrochemical behavior of Trp on the CUCR-LB/PrGO composite film was investigated, revealing a linear response range of Trp was 1.0×10-7 to 3.0×10-5 mol L-1 and a detection limit of 3.0×10-8 mol L-1. Furthermore, the developed electroanalytical method successfully determined Trp content in an amino acid injection samples. This study not only introduces a rapid and reliable electrochemical method for determination of Trp but also presents a new strategy for constructing high-performance electrochemical sensing platforms.

We present atomic structures and nonequilbrium synthesis of new class of materials, where the basic structural unit is a diamond tetrahedron. When units of one, two, and three tetrahedra are randomly packed, we create distinct phases of amorphous Q-carbon. Four tetrahedra in two adjacent layers lead to crystalline diamond lattice, which has four missing tetrahedra alternately. When these four missing tetrahedra are filled, we create subunit cell of crystalline Q-diamond. Theoretical calculations show that superconducting transition temperature (Tc) in 50 atomic % B-doped Q-diamond can reach near room temperature at ambient pressures. This is consistent with our earlier results using low-loss EELS measurements in 50 atomic % B-doped Q-carbon, which had mostly amorphous QB3 phase mixed with some crystalline Q-diamond phase. These EELS results showed that the Tc for these samples was in between 90K and 300K. Theoretical calculations of density of states, Eliashberg function, electron-phonon interaction parameter, and root-mean-square and logarithmic average of frequency in crystalline Q-diamond show Tc in the range of 268K to 300K, which is in a complete agreement with our EELS results in QB3.

Graphene-based nanoparticles possess remarkable physiochemical properties, making them promising for diverse applications in biomedicine, agriculture, food, and industrial applications. These nanoparticles have also been used in the fight against COVID-19. Human and environmental exposure to graphene-based nanomaterials is increasing at an unprecedented rate. However, there is still a huge knowledge gap regarding its safety in clinical applications. The topic remains controversial; although several routes of degradation exist, the cytotoxicity of graphene-based nanoparticles has been demonstrated. Various factors that can influence the cytotoxicity of graphene-based materials are discussed. This review summarizes the physiochemical properties of graphene-based materials and critically examines the possible effects of graphene-based nanoparticles on the molecular level and adverse health outcomes. While oxidative stress-mediated cell damage has been proposed as a primary cytotoxicity mechanism for graphene-based materials, various in vivo biodistribution and cytotoxicity mechanisms are also highlighted. Therefore, this review of the literature provides an overview of the cytotoxicity of GBMs and raises concerns about their widespread application with potential hazardous consequences on the environment and human health.

The development of biosensors with high sensitivity and low-detection limits provides a new direction for medical and personal care. Graphene and graphene derivatives have been used to prepare various types of biosensors due to their excellent sensing performance (e.g. high specific surface area, extraordinary electronic properties, electron transport capabilities and ultrahigh flexibility). This perspective review focuses on graphene-based biosensors for quantitative detection of cancer related biomarkers such as DNA, miRNA, small molecules and proteins by integrating with different signal outputting approaches including fluorescent, electrochemistry, surface plasmon resonance, surface enhanced Raman scattering etc. The article also discussed their challenges and potential solutions along with future prospects.

Polystyrene as a thin film on arbitrary substrates or pellets form defective graphene films or powders that can be dispersed in water and organic solvents. The materials were characterized by visible absorption, Raman and X-ray photoelectron spectroscopy, electron and atomic force microscopy and electrochemistry. Raman spectra of these materials show the presence of the expected 2D, G and D peaks at 2750, 1590 and 1350 cm^-1, respectively. The relative intensity of the G vs. the D peak is taken as a quantitative indicator of the density of defects in the G layer.

Within phototherapy, a grand challenge in clinical cancer treatments is to develop a simple, cost-effective, and biocompatible approach to treat this disease using ultra-low doses of light. Carbon-based materials (CBM), such as graphene oxide (GO), reduced GO (r-GO), graphene quantum dots (GQDs), and carbon dots (C-DOTs), are rapidly emerging as a new class of thera-peutic materials against cancer. This mini-review summarizes the progress in lasts years re-garding the applications of CBM in photodynamic (PDT) and photothermal (PTT) therapies for tumor destruction. The current understanding of the performance of modified CBM, hybrids and composites, is also addressed. This approach seeks to achieve an enhanced healing action by im-proving and modulating the properties of CBM to treat various types of cancer. Metal oxides, organic molecules, biopolymers, therapeutic drugs, among others, have been combined with CBM to treat cancer by PDT, PTT, or synergistic therapies.

Wastewater contaminated with antibiotics is a major environmental challenge. We developed here the green synthesis of bio-graphenes by using natural precursors (Xanthan, Chitosan, Boswellia, Tragacanth). The use of these precursors can act as templates to create 3D doped graphene structures with special morphology. Also, this method is a simple method for in-situ synthesis of doped graphenes. The elements present in the natural polymers (N) and other elements in the natural composition (P, S) are easily placed in the graphene structure and improve the catalytic activity due to the structural defects, surface charges, increased electron transfers, and the high absorption. In this mechanism, O2 dissolved in water absorbs onto the positive charged C in doped graphenes to create oxygenated radicals, which enables the degradation of antibiotic molecules. Light irradiation increases the amounts of radicals and rate of antibiotic removal. The results have shown that the hollow cubic Chitosan-derived graphene has shown the best performance due to the doping of N, S, and P. The Boswellia-derived grapheme shows the highest surface area, but lower catalytic performance, which indicates the more effective role of doping in the catalytic activity. The effect of oxygen and light were also studied to accelerate the degradation process.

In this paper we propose a simple procedure to obtain multi-walled carbon nanotubes (MWCNT) decorated with TiO₂-Ag nanoparticles (MWCNT-TiO₂-Ag). MWCNT were decorated with TiO2-Ag via combined functionalisation with -OH and –COOH groups and polymer wrapping technique using poly(allylamine hydrochloride) (PAH). TiO₂ modified Ag nanoparticles were synthesized through Pechini method using mixture of acetylacetonate-modified titanium (IV) isopropoxide with silver nitrate (the Ag+/Ti4+ atomic ratio, is 0.5, 1,0, 1.5, 2.0 and 2.5 %, respectively) and the L(+)-ascorbic acid, as reducing agents. XRD analysis revealed the formation of nanocomposite containing CNT, TiO₂ (anatase and rutile) and Ag. By SEM was evidenced the presence of the nanoparticles on MWCNT surface. The increases of the ratio between Ag⁺ and Ti⁴⁺ decrease the band gap energy of the samples. In Raman spectra the characteristic vibration of the TiO₂, Ag and C atoms of graphite are identified. The photocatalytic activity of the MWCNT-TiO₂-Ag nanocomposite was assessed by examining the degradation of Allura red (E129) aqueous solution under UV irradiation. The dye photodegradation process follows a pseudo – first – order kinetic with respect to the Langmuir – Hinshelwood reaction mechanism.

In our publication from 8 years ago1 we calculated RKKY interaction between two magnetic impurities in graphene. The consideration was based on the perturbation theory for the thermodynamic potential in the imaginary time representation and direct evaluation of real space spin susceptibility. Only the case of zero temperature was considered. We show in this short notice that the approach can be easily generalized to the case of finite temperature.

Graphene oxide was synthesized by a one-step environmentally friendly mechanochemistry process directly from graphite and characterized by Raman, FT-IR and UV/vis spectroscopies, Atomic Force Microscopy, X-ray Diffraction, Scanning Electron Microscopy, Energy-Dispersive X-ray Spectroscopy and Thermogravimetric Analysis. Spectroscopic analysis shows that the functional groups and oxygen content of the synthesized material are comparable with those of graphene oxide synthesized by other previously reported methods (Hummers). Thermogravimetric analysis reveals thermal stability up to 400 °C.

Hydroiodic acid (HI) treated - reduced graphene oxide (rGO) ink/conductive polymeric composites are considered as promising cold cathodes in terms of high geometrical aspect ratio and low field emission (FE) threshold devices. In this study, four simple, cost-effective, solution-processed approaches for rGO-based field effect emitters were developed, optimized and compared; rGO layers were coated on a) n+ doped Si substrate, b) n⁺-Si/P3HT:rGO, c) n⁺-Si/PCDTBT:rGO and d) n⁺-Si/PCDTBT:PC₇₁BM:rGO composites, respectively. The fabricated emitters were optimized by tailoring the concentration ratios of their preparation and field emission characteristics. In a critical composite ratio, FE performance was remarkably improved compared to the pristine Si, as well as n⁺-Si/rGO field emitter. In this context, the impact of various materials, such as polymers, fullerene derivatives, as well as different solvents on rGO function reinforcement and consequently on FE performance upon rGO-based composites preparation was investigated. The field emitter consisted of n⁺-Si/PCDTBT:PC₇₁BM(80%):rGO(20%)/rGO displayed a field enhancement factor of ∼2850, with remarkable stability over 20h and low turn-on field in 0.6V/μm. High-efficiency graphene-based FE devices realization paves the way towards low-cost, large-scale electron sources development. Finally, the contribution of this hierarchical, composite film morphology was evaluated and discussed.

Point-contact spectroscopy has been performed on bulk samples of electron-doped high temperature superconductor Nd2-xCexCuO4-. The samples were characterized by X-ray diffraction and scanning electron microscopy equipped with a wavelength dispersive spectrometer and an electron backscatter diffraction detector. The samples with a Ce content x = 0.15, show the absence of spurious phases and randomly oriented grains, most of which have dimensions of approximately 220 µm2. The low-bias spectra in the tunnelling regime, i.e., high transparency interface, exhibit a gap feature at about ±5 meV and no zero-bias conductance, consistent with the most literature data on oriented samples. The high-bias conductance has also been measured in order to obtain information on the properties of the barrier. A V-shape has been in some cases observed, instead of the parabolic behavior expected for tunnel junctions.

Zinc oxide is one of the most important semiconductor metal oxides and one of the most promising n-type materials, but its practical use is limited because of both its high thermal conductivity and its low electrical conductivity. Numerous studies have shown that doping with metals in ZnO structures leads to the modification of the band gap energy. In this work, Al-doped ZnO, Ni-doped ZnO, and undoped ZnO nanocrystalline powders were prepared by sol-gel method coupled with ultrasound irradiation. The doping concentration in ZnO was 1.0 at.% of Al and Ni. Influence of Al³⁺ and Ni²⁺ ions in the ZnO network are explored in this paper. X-ray Diffraction (XRD), Raman Spectroscopy, Nitrogen Adsorption (BET method), X-Ray Fluorescence (XRF) and Field Emission Scanning Electron Microscopy (FESEM) analyses demonstrated the incorporation of metal ions (aluminum and nickel) into the ZnO wurtzite structure. The crystallite size of the sample was decreased from 24.5 nm (ZnO) to 22.0 nm (ZnO-Al) and 21 nm (ZnO-Ni).

The rapid development of electric vehicles, unmanned aerial vehicles, and wearable electronic devices has led to a high interest in research related to the synthesis of graphene with a high specific surface area for energy applications. However, the problem of graphene synthesis scalability, as well as the lengthy duration and high energy intensity of the activation processes of carbon materials, are significant disadvantages. In this study, a reactor was developed for the green, simple, and scalable electrochemical synthesis of graphene oxide with a low oxygen content of 14.1 %. The resulting material was activated using a fast joule heating method. The processing of mildly oxidized graphene with a high–energy short electrical pulse (32 ms) made it possible to obtain a graphene–based porous carbon material with a specific surface area of up to 1984.5 m2/g. The low energy intensity, simplicity, and use of environmentally friendly chemicals render the proposed method scalable.

In the contemporary era, there has been a notable surge in the systematic utilization of therapeutic drugs that exhibit stimulus-responsive drug release patterns in specific target areas. However, challenges such as premature drug release and limited biocompatibility persist. To address these issues, the application of a lipid coating on mesoporous silica nanoparticles (MSNs) has emerged as a promising strategy. This lipid coating not only enhances the stability and biocompatibility of nanocarriers but also facilitates targeted drug delivery to diseased cells while minimizing drug release throughout the body. MSNs, renowned for their unique attributes including high porosity, morphology, and controllable pore size, have been widely recognized as suitable platforms for drug/gene delivery systems. Furthermore, graphene-based nanomaterials such as graphene oxide and reduced graphene oxide have garnered significant interest in the fields of biology and biomedicine. These materials possess exceptional characteristics such as a large surface area, distinct surface properties, high biocompatibility, and pH sensitivity, making them ideal candidates for incorporating drugs, genes, photosensitizers, and other cargo to design innovative drug delivery systems. This study aims to emphasize the ongoing efforts and advancements in enhancing the capacity and versatility of nanocomposites comprising graphene MSN composites for applications in drug delivery.

Plant extracts have been evaluated to determine their bioactivities and their potential use in wound healing. In this study, a conductive composite material, based on graphene oxide (GO), nanocellulose (CNF) and tannins (TA) from pine bark, reduced using polydopamine (PDA), was developed for wound dressing. The amount of CNF and TA was varied in the composite material and a complete characterization including SEM, FTIR, XRD, XPS, TGA was performed. Also, the conductivity, mechanical properties, cytotoxicity, and in vitro wound healing of the materials were evaluated. The results showed a successful physical interaction between CNF, TA and GO. In-creasing the CNF amount in the composite reduced the thermal properties, surface charge and conductivity of the material, but its strength, cytotoxicity and wound healing performance were improved. The TA incorporation slightly reduced the cell viability and migration, which may be associated with the doses used and the chemical composition of the extracts. However, the in vitro obtained results demonstrated that these composite materials can be suitable for wound healing.

The ability of 2D hybrid structures formed by boron, nitrogen and carbon atoms (h-BNCs) as potential substrates for surface enhanced Raman spectroscopy (SERS) detection of dioxin-like pollutants is theoretically analyzed. The strong confinement and high tunability of the electromagnetic response of the carbon nanostructures embedded within the h-BNC sheets point out that these hybrid structures could be promising for applications in optical spectroscopies, such as SERS. In this work, two model dioxin-like pollutants, TCDD and TCDF, and a model h-BNC surface composed by a carbon nanodisk of ninety-six atoms surrounded by a string of borazine rings, BNC96, are employed for the simulation of the adsorption complexes and the static and pre-resonance Raman spectra of the adsorbed molecules. A large affinity of BNC96 by these pollutants is reflected on the large interaction energies obtained for the most stable stacking complexes, with dispersion being the most important contribution to their stability. The large vibrational coupling of some active modes of TCDF and, specially, of TCDD makes the Raman static spectra display a ‘pure’ chemical enhancement of one order of magnitude. On the other hand, due to the strong electromagnetic response of BNC96, confined within the carbon nanodisk, pre-resonance Raman spectra obtained for TCDD and TCDF display large enhancement factors of 108 and 107, respectively. Promisingly, laser excitation wavelengths frequently used in SERS experiments also provoke significant Raman enhancements, around 104, for the TCDD and TCDF signals. Both the strong confinement of the electromagnetic response within the carbon domains and the high modulation of the resonance wavelengths within the visible and/or UV ranges in h-BNCs should lead to a higher sensitivity than graphene and white graphene parent structures, solving one of the main disadvantages of using 2D substrates for SERS applications.

Graphene is a two-dimensional nanostructured material with intrinsic properties that show promising performance in various applications, including electronics, renewable energy, medicine, mechanical enforcement and others. This study reports a bottom-up approach for the conversion of cyclohexane into graphene nanoflakes, which were then deposited onto fiberglass using a non-thermal generator. The composite was characterized using transmission electron microscopy, which revealed the formation of stacked few-layer graphene with a partially disordered structure and a d-spacing of 0.358 nm between the layers. X-ray diffraction confirmed the observations from the TEM images. SEM images showed the agglomeration of carbonaceous material onto the fiberglass, which experienced some delamination due to the synthesis method. Raman spectroscopy indicated that the obtained graphene exhibited a predominance of defects in its structure. Additionally, Atomic Force Microscopy (AFM) analyses revealed the formation of graphene layers with varying levels of porosity.

Pesticides are often used in different applications including agriculture, forestry, aquaculture, food industry, etc in order to insect pests and weeds. The indiscriminate usage of pesticides poses a massive threat to food, environmental and human health safety. Hence, the fabrication of a sensitive, and reliable sensor for the detection of pesticide residues in agro products and environmental samples is a critical subject to be considered. Recently, the graphene family including graphene oxide (GO) and reduced graphene oxide (rGO) have been frequently employed in the construction of sensors owing to their biocompatibility, high surface area to volume ratio, and excellent physiochemical, optical, and electrical properties. The integration of bio-recognition molecules with GO/rGO nanomaterials offers a promising detection strategy with outstanding repeatability, signal intensity, and low background noise. This review focuses on the latest developments (2018 to 2022) in the different types of GO/rGO-based biosensors such as surface plasmon resonance (SPR), fluorescence resonance energy transfer (FRET) and electrochemical based techniques, etc for pesticide analysis. The critical discussions on the advantages, limitations, and sensing mechanisms of emerging GO/rGO-based biosensors have been highlighted as well. Additionally, we explore the existing hurdles in GO/rGO-based biosensors, such as handling of difficult biological samples, reducing the total cost, and so on. This review also provides research gaps and viewpoints for future innovations in GO/rGO-based biosensors for pesticide determination mainly in areas with insufficient resources.

Graphene is a remarkable material with numerous applications. Due to its thin and lightweight design, it is ideal for a variety of applications. The synthesis of high-quality graphene in a cost-effective and environmentally friendly manner continues to be a significant challenge. Chemical reduction is considered to be the most advantageous method for preparing reduced graphene oxide (rGO). However, this process necessitates the use of toxic and harmful substances, which can have a detrimental effect on the environment and human health. Thus, to accomplish the objective, the green synthesis principle has prompted researchers worldwide to develop a simple method for green reduction of graphene oxide (GO), which is readily accessible, sustainable, economical, renewable, and environmentally friendly in nature. For example, the use of natural materials such as plants is generally considered safe. Furthermore, plants contain reducing and capping agents. The current review will focus on the discovery and application of rGO synthesis using extracts from a variety of different parts of the plant. The review aims to aid current and future researchers in their search for a novel plant extract that acts as a reductant in the green synthesis of rGO. The review aims to assist current and future researchers in their research for a novel plant extract that acts as a reductant in the green synthesis of rGO as well as their potential applications in a variety of industries.

Nanographene oxide (GOn) constitutes a nanomaterial of high value in the biomedical field. However, large scale production of highly stable aqueous dispersions of GOn is yet to be achieved. In this work, we explored high-power ultrasonication as a method to reduce particle size of GO and characterized the impact of the process in the physico-chemical properties of the material. GOn was obtained with lateral dimensions of 99 ±43 nm and surface charge of −39.9 ± 2.2 mV. High-power ultrasonication enabled an improvement of stability features, particularly by resulting in a decrease of the average particle size, as well as zeta potential, in comparison to GO obtained by low-power exfoliation and centrifugation (287 ± 139 nm; −29.7 ± 1.2 mV). Re-markably, GOn aqueous dispersions were stable for up to 6 months of shelf-time, with a global process yield of 74%. This novel method enabled the production of large volumes of highly con-centrated (7.5 mg mL-1) GOn aqueous dispersions. Chemical characterization of GOn allowed the identification of characteristic oxygen functional groups, supporting high-power ultrasonication as a fast, efficient and productive process for reducing GO lateral size, while maintaining the material’s chemical features.

Over the years, scarcity of fresh potable water has increased the demand for clean water. Meanwhile, with the advent of nanotechnology, the use of nanomaterials for photocatalytic degradation of pollutants in wastewaters has increased. Herein, a new type of nanohybrids of La and Mn co-doped bismuth ferrite (BiFeO₃) nanoparticles embedded into transition metal carbide sheets (MXene) were prepared by a low-cost double solvent sol-gel method, and investigated for their photocatalytic activity. The photoluminescence results showed that pure BFO has highest electron hole recombination rate as compared to all the co-doped BFO/MXene nanohybrids. The larger surface area and higher electron-hole pair generation rate provides suitable environment for fast photo-degradation of organic molecules. The band gap of the prepared nanohybrids was tuned to 1.96 eV having largest BiFeO₃ surface area (147 m²g⁻¹) reported till date. Moreover, the BLFO/MXene and BLFMO-5/Mxene degraded the 92% organic pollutant from water in dark and remaining in light spectrum as compare to undoped BFO/Mxene due to enhancement of the surface area and electron-hole recombination rate upon doping. Therefore, these synthesized nanohybrids could be a promising candidate for photocatalytic applications in future.

Influence of water concentration on the properties of fluorine-doped tin oxide (FTO) thin films was systematically studied in this work. Home made SISOM’s SPEED techniques and its chemical formulation was employed to grow the FTO on quartz substrate. Water concentration in the precursor solution was varied from 0, 0.5, 1.0 and 1.5 mol %. The structural, optical, and electrical properties of the films were studied under these deposition conditions. The results show that the properties of the films varied significantly with water concentration. Scanning electron microscopy (SEM) revealed FTO films whose grain size and uniformity increases significantly with increase in water concentration. The structure of the films was measured by X-ray diffraction (XRD) measurement. It shows polycrystalline films with (110), (101), (200), (211) and (220) orientation; the strength increases as water concentration increases. The optical transmission was determined by UV-Vis spectroscopy at 380–780 nm UV-VIS regions. The optical transmittance varies with water concentration with an average of 84%. The electrical property, measured by Hall Effect revealed n-type semiconductor. The films have the following properties: resistivity, 15 × 10^-4Ω cm; carrier concentration, 18.7 × 10¹⁹ cm^-3 and mobility of 21.86 cm² V^-1 s^-1. The average figure of merit, φ of the FTO film is 1.25. Optimum deposition condition was established after series of experiments and was found to be 1.5% water concentration at 460^oC substrate temperature. The FTO films deposited in this work could be a promising replacement to indium tin oxide (ITO) especially in dye-sensitized solar cells.

We report morpho-structural properties and charge conduction mechanisms of a foamy “graphene sponge”, having a density as low as ≈ 0.07 kg/m3 and a carbon to oxygen ratio C:O ≃ 13:1. The spongy texture analysed by scanning electron microscopy is made of irregularly-shaped millimetres-sized small flakes, containing small crystallites with a typical size of ≃ 16.3 nm. A defect density as high as ≃ 2.6×1011 cm−2 has been estimated by the Raman intensity of D and G peaks, dominating the spectrum from room temperature down to ≃ 153 K. Despite the high C:O ratio, the graphene sponge exhibits an insulating electrical behavior, with a raise of the resistance value at ≃ 6 K up to 5 orders of magnitude with respect to the room temperature value. A variable range hopping (VRH) conduction, with a strong 2D character, dominates the charge carriers transport, from 300 K down to 20 K. At T< 20 K, graphene sponge resistance tends to saturate, suggesting a temperature-independent quantum tunnelling. The 2D-VRH conduction originates from structural disorder and is consistent with hopping of charge carriers between sp2 defects in the plane, where sp3 clusters related to oxygen functional groups act as potential barriers.

In this work, oxygen-doped g-C3N4 mesoporous nanosheets (O-CNS) were synthesized via a facile recrystallization method with the assistance of H2O2. The crystal phase, chemical composition, morphological structure, optical property, electronic structure and electrochemical property of the prepared O-CNS samples were well investigated. The morphological observation combining with nitrogen adsorption-desorption results demonstrated that the prepared O-CNS samples possessed nanosheets-like morphology with porous structure. The O doping into g-C3N4 resulted in the augment of specific surface area, which could provide more active sites for photocatalytic reaction. Simultaneously, the visible-light absorption capacity of O-CNS samples was boosted owing to the regulation of O doping. The built energy level induced by the O doping could accelerate the migration rate of photoinduced carriers, and the porous structure was most likely to speed up the release of hydrogen during photocatalyic hydrogen process. Resultantly, the photocatalytic hydrogen production rate of the optimized oxygen-doped g-C3N4 nanosheets reached up to 2012.9 μmol•h-1•g-1, which was 13.4 times higher than that of bulk g-C3N4. Thus, the significantly improved photocatalytic behavior was imputed to the porous structure, the augment of active sites, and the enhancement of visible light absorption and charge separation efficiency.

A series of ZnO doped nitrogen-carbon materials (xZnO-N-C) with ZnO content of 5-40% are prepared by vacuum curing-carbonization strategy using polyamide-imide as N-C source and zinc nitrate as metal source for propane dehydrogenation (PDH). 20ZnO-N-C exhibits outstanding initial activity (propane conversion of 35.2% and propene yield of 24.6%) and relatively low deactivation rate (0.071 h-1) at 600 ◦C. The detailed characterization results show that small ZnO nanoparticles (5.5 nm) with high dispersion on the catalyst could be obtained by adjusting ZnO loading. Moreover, much more nitrogen-based species especially ZnNx species are formed on 20ZnO-N-C by comparison with 20ZnO-N-C-air prepared by curing-carbonization without vacuum, which may contribute for the higher product selectivity and catalytic stability of 20ZnO-N-C. The probable active sites for PDH reaction on the catalyst system are proposed to be C=O species and Zn2+ species. Moreover, the aggregation of ZnO nanoparticles is the primary reason for the activity loss on this catalyst system. The present finding not only provides the feasible construction strategy for the metal oxide doped nitrogen-carbon materials but also valuable guidance for the design of efficient catalyst in dehydrogenation of light alkane.

Acetaldehyde decomposition was performed under heating at the temperature range of 25-125oC and UV irradiation on TiO2 doped by the metallic Ni powder and TiO2 supported on the nickel foam. Process was carried out in high temperature reaction chamber “The Praying MantisTM”, with simultaneous in situ FTIR measurements and UV irradiation. Ni powder was added to TiO2 in the quantity of 0.5 to 5.0 wt%. Photothermal measurements of acetaldehyde decomposition indicated, that the highest yield of acetaldehyde conversion on TiO2 und UV irradiation was obtained at 75oC. Doping of nickel to TiO2 did not increase its photocatalytic activity. Contrary to that, application of nickel foam as a support for TiO2 appeared to be highly advantageous, because increased decomposition of acetaldehyde from 31 to 52% at 25oC and then to 85% at 100oC by comparison with TiO2 itself. At the same time mineralisation of acetaldehyde to CO2 increased two times at the presence of nickel foam. However, oxidised nickel foam used as support for TiO2 was detrimental. Most likely, different mechanisms of electrons transfer between Ni-TiO2 and NiO-TiO2 occurred. Application of nickel foam greatly enhanced separation of free carriers in TiO2. As a consequence, high yields of the photocatalytic reactions were obtained.

ZnO films with Ti atoms incorporated (TZO) in a wide range (0-18 at. %) have been grown by reactive co-sputtering on silicon and glass substrates. The influence of the titanium incorporation in the ZnO matrix on the structural and optical characteristics of the samples has been determined by Rutherford backscattering spectroscopy (RBS), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results indicate that the samples with low Ti content (< 4 at. %) exhibit the wurtzite-like structure, with the Ti+4 ions substitutionally incorporated into the ZnO structure, forming Ti-doped ZnO films. In particular, very low concentration of Ti (<0.9 at. %) leads to a significant increase of the crystallinity of the TZO samples. Higher Ti contents give rise to a progressive amorphization of the wurtzite-like structure so samples with high Ti content (≥18at. %), displays an amorphous structure indicating the XPS analysis a predominance of Ti-O-Zn mixed oxides. The energy gap, obtained from absorption spectrophotometry, increases from 3.2 eV for pure ZnO films to 3.6 eV for those with the highest Ti content. Ti incorporation in the ZnO samples below 0.9 at. % rises both, the blue (380 nm) and green (550 nm) bands of the photoluminescence (PL) emission, thereby indicating a significant improvement of PL efficiency of the samples.

Carboxylic acids such as acetic acid and propionic acid have been investigated as representative components for fast pyrolysis (FP) bio-oil upgrading. Selective catalytic conversion of carboxylic acids can enhance bio-refinery processing economics through catalyst preservation and process intensification. Various metal-doped molybdenum carbide bead catalysts have been synthesized and developed in this work. Our aim is to enable selective conversion of carboxylic acids. In the case of acetic acid conversion, calcium doped Mo₂C beads offer the highest yield of acetone ~96% at 450 °C among undoped and Ca or Ni doped catalysts. By comparing hot gas filter with and without Ca-Mo₂C catalyst tested with real FP vapors, the former showed a 36.7% reduction of acetic acid, a 37.5% reduction of small ketones in aqueous phase, and a ~50% reduction of methoxies (methoxy phenols and methoxy aromatics) in organic phase. The conversion resulted in the formation of more long chain chemicals in the organic phase, which are more amendable for downstream upgrading.

A series of Eu³⁺ doped CaSiO₃/SiO₂ nano-phosphor powder of controlled grain size, crystalline structure, and chemical composition were synthesized using the microemulsion technique. XRD profiles of samples sintered over 600 of suggested phase shift from amorphous powder grain to more ordered polycrystalline powder of triclinic type wollastonite, CaSiO₃, with preferred crystal phase orientation of (112) and tetragonal type cristobalites of SiO₂. The grain size, crystallinity, and chemical composition of the host matrix, activator and sensitizer strongly affected both the absorption and emission bands of these samples. The amplitude of both the orange and red emission bands significantly increased with sintering temperature. The emission band is red-shifted with decreasing grain sizes. These bands displayed good sensitivity to ionic concentration of the Si⁴⁺, Ca²⁺, and Eu³⁺. With increasing Ca²⁺ ion concentration both the intensity of the red photoluminescence (PL) band increased and a concentration quenching observed. Increase in Si⁴⁺ ion concentration led to quenching in PL intensity of both the orange and red bands whereas the amplitude of the blue-band slightly increased. With increasing Eu³⁺ ion concentration the red-band initially increased whereas it started decreasing at higher sample concentration. In the presence of Ca²⁺ ion as a sensitizer, the sample showed a remarkable PL property—including—about 100% photon conversion efficiency and a two-fold increase in excitation and emission photons.

Tantalum doped ZnO structures (ZnO:Ta) were synthesized and some of their characteristics were studied. ZnO material was deposited on silicon substrates by using a hot filament chemical vapor deposition (HFCVD) reactor. The raw materials were a pill made of a mixture of ZnO and Ta₂O₅ powders, and molecular hydrogen was used as a reactant gas. Percentage of tantalum was varied from 0 to 500 mg by varying the percentage of tantalum oxide in the mixture of the pill source, by holding a fixed amount of 500 mg of ZnO in all experiments. X-ray diffractograms confirmed the presence of zinc oxide in the wurtzite phase and metallic zinc with a hexagonal structure, and no other phase was detected. Displacements to lower angles of reflection peaks, compared with those from samples without contamination, were interpreted as the inclusion of the Ta atoms in the matrix of the ZnO. This fact was confirmed by EDS and XRD measurements. From SEM images from undoped samples exhibited mostly micro sized semi-spherical structures while doped samples displayed a trend to grown as nanocrystalline rods. The presence of tantalum during the synthesis affects the way of the growth. Green photoluminescence at naked eye was observed when Ta doped samples were illuminated by ultraviolet radiation and confirmed by PL spectra. PL intensity on Ta doped ZnO varied from those undoped samples up to 8 times.

A 3D graphene foam made of interconnected multilayer graphene flakes was produced on optical fibres (OF) by laser-induced transformation of a polyimide (PI) film coated on the OF cladding. This material, known as la-ser-induced graphene (LIG), was explored in the electrochemical detection and quantification of dopamine (DA) at physiologically relevant concentrations in the presence of the most relevant interfering molecules in biological fluids, ascorbic acid (AA) and uric acid (UA). The measured limit of detection is 100 nM, the linear range is 0.1 to 5 μM and a maximum sensitivity of 5.0 µA µM−1 cm−2 was obtained for LIG decorated with Pt nanoparticles (NPs). Moreover, immunity to AA and UA interference and to fouling was attained by decorating the LIG elec-trode with Pt NPs and coating with Nafion. These figures of merit underlines the potential of these sensors for the quantification of physiologically relevant concentrations of DA in biological fluids, paving the way for the development of hybrid electrochemical/optical sensing actuating platforms in a lab-on-fibre configuration, with relevant applications in biomedical engineering. The advantages of this hybrid arrangement include the possi-bility of in-situ counterproofing, extended measuring ranges, photoelectrochemical detection and the probing of inaccessible places. This elegant approach can also provide a simple and cost-effective way to fabricate biomed-ical devices with extended functionality, such as medical optical probes with added electrochemical capabilities, optogenetics combined with local electrochemical detection, among others.

Owing to their extraordinary properties, carbon-based nanomaterials are gaining traction in biomedicine. Green synthesis is the cost-effective method for fabricating carbon-based nanomaterials due to its rapidity, renewable nature, and sustainability. This study emphasis on the graphene oxide (GO) reduction using a simple one-pot technique that does not require the use of toxic reducing agents. This article reports the green synthesis of reduced graphene oxide (RGO) using Hibiscus sabdariffa L. calyxes extract as the natural reducing agent. Additionally, this article also provides analysis RGO using X-ray diffraction (XRD), UV-Visible spectroscopy (UV-Vis), and Raman spectroscopy. XRD result showed that the GO peak at 11o diminished, and a new hump appear at 22o indicating that the GO is fully reduced when it is refluxed for 6 hours, at 100oC with 1:3 ratio of GO:PE. The UV-Vis data indicated absorption peak of GO (237 nm) and RGO (265 nm) at distinct locations. This finding shed new light on the enormous potential of Hibiscus sabdariffa L. calyxes extract for green GO reduction. As a result, this environmentally friendly method can help reduce dependence on chemical materials.

In the present work, the state of the art of the most common additive manufacturing (AM) technologies used for the manufacturing of complex shape structures of graphene-based ceramic nanocomposites, ceramic and graphene-based parts is explained. A brief overview of the AM processes for ceramic, which are grouped by the type of feedstock used in each technology, is presented. The main technical factors that affect the quality of the final product were reviewed. The AM processes used for 3D printing of graphene-based materials are described in more detail; moreover, some studies in a wide range of applications related to these AM techniques are cited. Furthermore, different feedstock formulations and their corresponding rheological behaviour were explained. Additionally, the most important works about the fabrication of composites using graphene-based ceramic pastes by Direct Ink Writing (DIW) are disclosed in detail and illustrated with representative examples. Various examples of the most relevant approaches for the manufacturing of graphene-based ceramic nanocomposites by DIW are provided.

A quantitative method is proposed to determine of Stone-Wales defects for carbon nanostructures with sp2 hybridization of carbon atoms. The technique is based on the diene synthesis reaction (Diels-Alder reaction). The proposed method was used to determine Stone-Wales defects in the few-layer graphene (FLG) nanostructures synthesized by the self-propagating high-temperature synthesis (SHS) process, in reduced graphene oxide (rGO) synthesized based on the method of Hammers and in the single-walled carbon nanotubes (SWCNT) TUBAL trademark, Russia. Our research has shown that the structure of FLG is free of Stone-Wales defects, while the surface concentration of Stone-Wales defects in TUBAL carbon nanotubes is 1.1×10-5 mol/m2 and 3.6×10-5 mol/m2 for rGO.

The nitrogen-doped amorphous oxide semiconductor (AOS) thin film transistors (TFTs) with double-stacked channel layers (DSCL) were prepared and characterized. The DSCL structure composed of nitrogen-doped amorphous InGaZnO and InZnO films (a-IGZO:N/a-IZO:N or a-IZO:N/a-IGZO:N) made the corresponding TFT devices exhibit quite large field-effect mobility due to the existence of double conduction channels. Especially, the a-IZO:N/a-IGZO:N TFTs showed even better electrical performance (μ_FE = 15.0 cm²·V^-1·s^-1, SS = 0.5 V/dec, V_TH = 1.5 V, I_ON/I_OFF = 1.1×10⁸) and stability (V_TH shift of 1.5, -0.5, and -2.5 V for positive bias-stress, negative bias-stress and thermal stress tests, respectively) than the a-IGZO:N/a-IZO:N TFTs. Based on the X-ray photoemission spectroscopy measurements and energy band analysis, it was assumed that the optimized interface trap states, the less ambient gas adsorption, and the better suppression of oxygen vacancies in the a-IZO:N/a-IGZO:N hetero-structures might be responsible for the better behaviors of the corresponding TFTs.

Graphene is a two-dimensional carbon atom with a hexagonal honeycomb-like structure in which the sp2 hybridization occurs. GO sheets are highly oxidized and have oxygen-containing groups. Properties of electronics, mechanicals, magnetics, and optics, Oxidized Methods for Brodies, Staudenmaier, Hofmann, Hummers, Improved Hummers, and Tour's Methods Reduction of Graphene oxide methods Chemical Reduction using sodium borohydride, 2,4-dinitrophenylhydrazine, Hydrazine hydrate, Thermal Reduction, Hydrothermal Reduction, Exfoliation Reduction, Catalytic Reduction, and the green synthesis route for reduction, The reduction of graphene oxide has a wide range of applications, including its use in energy storage devices for Solar cells, Supercapacitors, LIG-based sensors, River Water sensors, Battery, hydrovoltaic generators, OLED Screen, and Graphene Shielding. This review will determine the future of a few applications.

Laser reduced graphene oxide (LRGO) on a PET substrate was prepared in one-step to obtain the LRGO grid electrode for sensitive carbaryl determination. The grid form results in a grid distribution of different electrochemically active zones affecting the electroactive substance diffusion towards to the electrode surface and increasing the electrochemical sensitivity for carbaryl determination. Carbaryl is electrochemically irreversibly oxidized by the secondary amine moiety of the molecule with the loss of one proton and one electron in the pH range from 5 to 7 by LSV on the LRGO grid electrode with a scan rate of 300 mV/s. Some interference of the juice matrix molecules did not significantly affect the LSV oxidation current of carbaryl on the LRGO grid electrode after adsorptive accumulation without applied potential. The LRGO grid electrode can be used for LSV determination of carbaryl in fruit juices in the concentration range from 0.25 to 128 mg/L with LOD of 0.1 mg/L by. The fabrication of the LRGO grid electrode opens up possibilities for further inexpensive monitoring of carbaryl in other fruit juices and fruits.

We numerically study surface models defined on hexagonal disks with a free boundary. 2D surface models for planer surfaces have recently attracted interest due to the engineering applications of functional materials such as graphene and its composite with polymers. These 2D composite meta-materials are strongly influenced by external stimuli such as thermal fluctuations if they are sufficiently thin. For this reason, it is very interesting to study the shape stability/instability of thin 2D materials against thermal fluctuations. In this paper, we study three types of surface models including Landau-Ginzburg (LG) and Helfirch-Polyakov models defined on triangulated hexagonal disks using the parallel tempering Monte Carlo simulation technique. We find that the planer surfaces undergo a first-order transition between the smooth and crumpled phases in the LG model and continuous transitions in the other two models. The first-order transition is relatively weaker compared to the transition on spherical surfaces already reported. The continuous nature of the transition is consistent with the reported results, although the transitions are stronger than that of the reported ones.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

This study focuses on the development and characterization of a series of six new dansyl derivatives (L1 to L6) and their integration into PMMA polymers for application in environmental sensing. The photophysical properties of these derivatives were extensively studied in various solvents and in solid state. A remarkable positive solvatochromic effect was observed, indicating their potential in microenvironmental polarity assessment. The dansyl derivatives demonstrated selective sensing capabilities for Cu2+ and Hg2+ metal ions, with the formation of mononuclear species. Additionally, their acid-base responsive nature was explored, revealing potential for pH-sensitive applications. The incorporation of these derivatives into PMMA polymers resulted in acid-base sensitive materials suitable for environmental monitoring, particularly in detecting hazardous gases and changes in pH levels. This integration overcomes the solubility limitations of dansyl compounds and extends their applicability in diverse sensing scenarios.

The solid-state technique was utilized to make a single phase of delafossite CuAlO2, along with 1%, 2%, 3% and 4% silver doped CuAlO2 samples in this study. The content of the samples was investigated using energy dispersive X-ray spectroscopy (EDS) equipped with a field emission scanning electron microscope (FE-SEM). The polycrystalline nature of all of the analyzed cases was confirmed by structural analyses utilizing an X-ray diffraction (XRD) pattern with a simple typical peak of CAO rhombohedral phase. Raman, FT-IR and UV–Vis spectroscopy were used to study the structural, and optical energy band gap (Eg) of Ag doped CuAlO2 nanoparticles. The Kubelka–Munk function was used to calculate the optical band gap of ACAO alloys using diffuse reflectance spectra, and it altered as the Ag ion concentration increased. A. c. impedance spectroscopy was used to investigate the dielectric characteristics of Ag doped CuAlO2 nanoparticles.

Mn-doped CeO2 and CeO2 with the same morphology (nanofiber and nanocube) were synthesized through hydrothermal method respectively. When applied to benzene oxidation, the catalytic properties of Mn-doped CeO2 were higher than those of CeO2, which was related with the concentration of O vacancy. Compared to CeO2 with the same morphology, more oxygen vacancies were formed on the surface of Mn-doped CeO2, due to Mn ion replacing Ce ion. The lattice replacement was analyzed through XRD, Raman, electron energy loss spectroscopy and electron paramagnetic resonance technology. The formation energies of oxygen vacancy on the different exposed crystal planes [(110) and (100)] for Mn-doped CeO2 were calculated by applying the density functional theory (DFT). The data showed that the oxygen vacancy was easier to be formed on the (110) plane. The factors influencing catalytic behavior were elaborated, which indicated that surface oxygen vacancy played an important part in catalytic reaction.

Cobalt ferrite nanoparticles (NPs) doped with rare earth (RE) metals with general formula CoFe_2-xRE_xO₄ (RE=Yb, Dy, Gd; x = 0.0 - 0.3) were synthesized by the co-precipitation method followed by post thermal treatment. The influence of RE doping on structural, magnetic and thermal properties and potential biomedical applications like magnetic hyperthermia has been investigated. In the as-prepared samples RE cations enter the spinel lattice as detected by X-ray diffraction. Thermal treatment leads to thermodynamically stable and relaxed single-phase spinel structures only for lower RE content, x = 0.01-0.05. However, annealed samples present higher mass magnetization values (M_S), up to 83 Am²/kg. RE content also affects M_S, especially in the case of annealed samples where it decreases linearly with x from about 80 Am²/kg (x = 0.01) to about 60 Am²/kg (x = 0.30). Thermal treatment induces a reduction in coercivity from 60-100 mT for as-prepared samples to 18-33 mT for annealed samples, in a nonlinear manner with respect to RE content. Heating efficiency, i.e., Specific Loss Power (SLP), of all samples has been studied using both magnetometric and calorimetric method to deeper examine the energy loss mechanisms involved.

To realize high response and selectivity gas sensor in detecting dissolved gases in transformer oil, in this study, the adsorption of four kinds of gases (H2, CO, C2H2 and CH4) on Pd-graphyne as well as the gas sensing properties evaluation were investigated. The energetically favorable structure of Pd doped γ-Graphyne was first studied, including the comparison of different adsorption sites and discussion of electronic properties. Then, the adsorption of these four molecules on Pd-graphyne was explored. The adsorption structure, adsorption energy, electron transfer and electron distribution, the band structure and density of states were calculated and analyzed. The results show that the Pd atom prefers to be adsorbed on the middle of three C≡C bonds and the band gap is smaller. The CO adsorption exhibits the largest adsorption energy and electron transfer and brings obvious change to the structure and electron properties to Pd-graphyne. Because of the conductance decrease after adsorption CO and acceptable recovery time at high temperature, the Pd-graphyne can be promising gas sensing materials to detect CO with high selectivity. This work offers theoretical support for the design of nanomaterials based gas sensor using novel structure for industrial application.

Graphene-based Field-Effect Transistors (FETs) integrated with microstrip patch antennas offer a promising approach for Terahertz signal radiation. In this study, a dual-stage simulation methodology is employed to comprehensively investigate the device’s performance. The initial stage, executed in MATLAB, delves into charge transport dynamics within a FET under asymmetric boundary conditions, employing hydrodynamic equations for electron transport in the graphene channel. Electromagnetic field interactions are modeled via Finite-Difference Time-Domain (FDTD) techniques. The second stage, conducted in COMSOL Multiphysics, focuses on the microstrip patch antenna’s radiative characteristics. Notably, analysis of the S11 curve reveals minimal reflections at the FET’s resonant frequency of 1.34672 THz, indicating efficient impedance matching. Examination of the radiation pattern demonstrates the antenna’s favorable directional properties. This research underscores the potential of graphene-based FETs for Terahertz applications, offering tunable impedance matching and high radiation efficiency for future Terahertz devices.

Laser-induced graphene (LIG) has gained considerable attention recently due to its unique properties and potential applications. In this study, we investigate using LIG in polyimide (PI) as a material for antenna applications. The LIG-PI composite material was prepared by a facile picosecond laser (1064 nm) irradiation process, which resulted in a conductive graphene network within the PI matrix. Furthermore, LIG formation was confirmed by Raman spectroscopy and sheet resistance measurements. Finally, a patch antenna from LIG for 2.45 GHz microwaves was simulated, produced and tested. These findings suggest that LIG-PI composites have great potential for use in high-frequency electronic devices and can provide a new avenue for the development of flexible and wearable electronics.

The wide application of graphene in the industry requires the direct growth of graphene films on silicon substrates. In this study, we find a possible technique to meet the requirement above. Multilayer graphene thin films (MLG) are grown without a catalyst on Si/SiO2 by pulsed laser deposition (PLD). It was found that the minimum number of laser pulses that are required to produce fully covered (uninterrupted) samples is 500. This number of laser pulses resulted in samples that contain ~5 layers of graphene. The number of layers was not affected by the laser fluence and the sample cooling rate after the deposition. However, the increase of the laser flu-ence from 0.9 J/cm2 to 1.5 J/cm2, results in 2.5 fold reduction of the MLG resistance. The present study reveals that the PLD method is suitable to produce nanocrystalline multilayer graphene with electrical conductivity of the same magnitude as commercial CVD graphene samples.

In this work, thermo-responsive block copolymer brushes modified graphene oxide (GO) nanohybrid was fabricated successfully via the host-guest interaction between β-cyclodextrin functionalized GO and azobenzene-terminated PNIPAM-b-P(St-co-MQ). The block copolymer was synthesized using reversible addition fragmentation chain transfer (RAFT) polymerization based on the monomers of N-isopropylacrylamide (NIPAM), 5-(2-methacryloyl-ethyloxymethyl) -8-quinolinol (MQ), styrene (St) and an azobenzene functional RAFT agent. The 8-hydroxyquinoline units containing in the block polymer can coordinate with CdSe/ZnS quantum dots(QDs) to form a CdSe/ZnS QDs-block copolymer brushes modified graphene oxide fluorescence nanohybrid (QDs/polymer/GO fluorescence nanohybrid) and the resulting fluorescence nanohybrid had a robust temperature responsive property which result from the change in the PNIPAM conformation in the block copolymer on the surface of GO.

Dynamic phase modulation is vital for tunable focusing, beaming, polarization conversion and holography. However, it remains challenging to achieve full 360∘ dynamic phase modulation while maintaining high reflectance or transmittance based on metamaterials or metasurfaces in the terahertz regime. Here we propose a doubly resonant graphene-metal hybrid metasurface to address this challenge. Simulation results show that by varying the graphene Fermi energy, the proposed metasurface with two shifting resonances is capable to provide dynamic phase modulation covering a range of 361∘ while maintaining relatively high reflectance above 20% at 1.05 THz. Based on the phase profile design, dynamically tunable beam steering and focusing are numerically demonstrated. We expect this work will advance the engineering of graphene metasurfaces for the dynamic manipulation of terahertz waves.

We explore the implementation of specific optical properties of armchair graphene nanoribbons (AGNRs) through edge-defect manipulation. This technique employs the tight-binding model in conjunction with the calculated absorption spectral function. Modification of the edge states gives rise to the diverse electronic structures with striking changes in the band gap and special flat bands at low energy. The optical-absorption spectra exhibit exotic excitation peaks and they strongly depend on the type and period of the edge extension. Remarkably, there exist the unusual transition channels associated with the flat bands for selected edge-modified systems. We discover the special rule governing how the edge-defect influences the electronic and optical properties in AGNRs. Our theoretical prediction demonstrates an efficient way to manipulate the optical properties of AGNRs. This might be of importance in the search for suitable materials designed to have possible technology applications in nano-optical, plasmonic and optoelectronic devices.

Graphene as a new two-dimensional material can be utilized to design tunable optical devices owing to its exceptional physical properties such as high mobility and tunable conductivity. In this paper, we present the design and analysis of a tunable broadband terahertz absorber based on periodic graphene ring arrays. Due to plasmon hybridization modes excited in the graphene ring, the proposed structure achieves a broad absorption bandwidth with more than 90% absorption in the frequency range of 0.88-2.10THz under normal incidence and its relative absorption bandwidth is about 81.88%. Meanwhile, it exhibits polarization-insensitive behavior and maintains high absorption over 80% when incident angle is up to 45º for both TE and TM polarizations. Additionally, the peak absorption rate of the absorber can be tuned from 21% to nearly 100% by increasing the graphene’s chemical potential from 0eV to 0.9eV. Such a design can have some potential applications in various terahertz devices, such as modulators, detectors, spatial filters.

Developing sustainable and renewable energy sources is critical as higher and higher global energy and environmental challenges arise. Hydrogen has the highest mass/energy density of any fuel and is considered one of the best sources of clean energy. Water splitting is regarded as one of the most promising solutions for hydrogen production on a large scale. Highly efficient, durable and cost-effective catalysts for hydrogen evolution reaction (HER) are critical in the realization of this goal. Among many materials proposed, graphene-based materials offer some unique properties for HER catalysis. In this review, we present recent progress on development of graphene-based electrocatalysts toward HER throughout the past few years.

We report the growth of graphene at a low temperature using the cold wall chemical vapor deposition technique (CWCVD). Few layered (~6-8 layers) graphene were grown on nickel-coated silicon with acetylene as the precursor gas. The advantage of the combination of the acetylene (as a carbon feedstock) and the nickel catalyst was the lowering of the graphene growth temperature. Nickel coated silicon samples were pre-treated (heat treatment in inert atmosphere) before the growth and the effect of the pre-treatment on the catalyst as well as on the grown film was studied. The final samples were characterized with scanning electron microscopy and Raman spectroscopy. In CWCVD route, the heating of only the substrate holder enabled high heating and cooling rates, which, along with the control over partial pressure of the precursor gas had profound effect on the formation of graphene. In the best sample we have achieved almost equal intensity of the G and 2D peaks in Raman spectrum, which implied about ~6-8 layers of Graphene. The defect peak (the D band) was extremely small in the sample and it was attributed to the ripples and the underlying roughness of the nickel film. We analyzed that a proper choice of the thickness of catalyst layer and a higher cooling rate after graphene growth it would be possible to obtain monolayered graphene. Similar samples grown in a normal atmospheric CVD (with some engineered design to promote fast cooling) were also compared with the cold wall CVD grown samples and plasma assisted CWCVD, and cold-wall CVD demonstrated a better control over the quality of graphene film through the fast cooling and a controlled partial pressure of the precursor gas.

Carbon nanomaterials with a different character of the chemical bond – graphene (sp2) and nanodiamond (sp3) are the building bricks for a new class of all-carbon hybrid nanomaterials, where the two different carbon networks with the sp3 and sp2 hybridization coexist, interact and even transform into one another. The unique electronic, mechanical, and chemical properties of the two border nanoallotropes of carbon ensure the immense application potential and versatility of these all-carbon graphene – diamond nanomaterials. The review gives an overview of the current state of the art of graphene – diamond nanomaterials, including their composites, heterojunctions, and other hybrids for sensing, electronic, energy storage, and other applications. Also, the graphene-to-diamond and diamond-to-graphene transformations at the nanoscale, essential for innovative fabrication, and stability and chemical reactivity assessment are discussed based on extensive theoretical, computational, and experimental studies.

Intercalation of noble metals can produce giant Rashba-type spin-orbit splittings in graphene. The spin-orbit splitting more than 100 meV has not yet been achieved in graphene on a metallic or a semiconductor substrate. Here, we report the p-type graphene obtained by Pt intercalation of zero-layer graphene on SiC substrate. The spin splitting of ∼200 meV was observed at a wide range of binding energies. Comparing the results of theoretical studies of different models with the experimantal ones measured by spin-ARPES, XPS and STM methods, we came to the conclusion that inducing giant spin-orbit splitting requires not only a fairly close arrangement of graphene to Pt layer, but also the presence of graphene corrugation caused by non-flat Pt layer. This makes it possible to find a compromise between strong hybridization and increased spin-orbit interaction. In our case, this is achieved by forming Pt submonolayer ordered on a nanometer scale under graphene.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Density functional theory (DFT) and coupled cluster theory (CCSD(T)) calculations are performed to investigate the geometric, electronic structures and chemical bonding of a series of Cu-doped zinc oxide clusters, CunZn3O3 (n = 1-4). The structural evolution of CunZn3O3 (n = 1-4) clusters are elaborated in our work. The planar seven-membered ring of CuZn3O3 cluster plays an important role in the structural evolution, that is, the Cu atom, Cu dimer (Cu2) and Cu trimer (Cu3) anchor on the CuZn3O3 cluster. The aggregate behavior of Cu atoms on Zn3O3 may offer insight into the study of Cu/ZnO-based catalysts. Additionally, it is found that the CunZn3O3 clusters become more stable as the Cu content (n) increases. Bader charge analysis points out that as the Cu atoms doping, the reducibility of Cu aggregation (Cun-1) on the CuZn3O3 cluster increases. Combined with the d-band centers and the surface electrostatic potential (ESP), the reactivity and the possible reaction sites of CunZn3O3 (n = 1-4) clusters are also illustrated.

The work reports a facile synthesis of high thermally-stable nanocrystalline anatase TiO2 nanoparticles (NPs) doped with different atomic concentrations (0.5, 1.0, 3.0, and 6.0%) of Gd3+ and Nd3+ ions by a template-free and one-step solvothermal process, using titanium(IV) butoxide as titanium precursor and dimethyl sulfoxide (DMSO) as solvent. The structure and morphology of the Gd3+, Nd3+, and 0.5%Gd3+-0.5%Nd3+/doped TiO2 NPs have been characterized by using various analytical techniques. The Gd3+/ and Nd3+/TiO2 molar ratios were found to have a pronounced impact on the crystalline structure, size, and morphology of TiO2 NPs. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) studies revealed the proper substitution of Ti4+ by Gd3+ and Nd3+ ions in the TiO2 host lattice. The as-prepared Gdx/TiO2, Ndx/TiO2, and Gd1.0/Ndx/TiO2 bimetallic NPs, x = 0.5, 1.0, 3.0, and 6%, have been investigated as electrocatalysts for hydrogen evolution reaction (HER) in 1.0 M KOH solution using a variety of electrochemical techniques. At any doping percentage, the Gd1.0/Ndx/TiO2 bimetallic NPs showed higher HER catalytic performance than their corresponding counterparts i.e. Gdx/TiO2 and Ndx/TiO2. Upon increasing the Nd content from 0.5 to 6.0%, the HER catalytic performance of the Gd1.0/Ndx/TiO2 bimetallic NPs was generally enhanced. Among the studied materials, the bimetallic Gd1.0/Nd6.0/TiO2 NPs emerged as the most promising catalyst with an onset potential of -22 mV vs. RHE, a Tafel slope of 109 mV dec-1, and an exchange current density of 0.72 mA cm-2. Such HER electrochemical kinetic parameters are close to those recorded by the commercial Pt/C (onset potential: -15 mV, Tafel slope: 106 mV dec-1, and exchange current density: 0.80 mA cm-2), and also comparable with those measured by the most active electrocatalysts reported in the literature. The synergistic interaction of Gd and Nd is thought to be the major cause of the bimetallic catalyst's activity.

There was a question on “how lanthanides doping in iron oxide affects cure kinetics of epoxy-based nanocomposites?” To answer, we synthesized samarium (Sm)-doped Fe3O4 nanoparticles via electrochemical method and characterized it using FTIR, XRD, FE-SEM, EDX, TEM, and XPS analyses. The magnetic particles were uniformly dispersed in epoxy resin to increase the curability of the epoxy/amine system. The effect of the lanthanide dopant on the curing reaction of epoxy with amine was explored by modeling DSC experimental data based on model-free methodology. It was found that Sm3+ in the structure of Fe3O4 crystal participates in cross-linking of epoxy by catalyzing the reaction between epoxide rings and amine groups of curing agents. In addition, the etherification reaction of active OH groups on the surface of nanoparticles reacts with epoxy rings which prolongs the reaction time at the late stage of reaction where diffusion is the dominant mechanism.

Iron Doped TiO₂ nanoparticles (Fe-TiO₂) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO₂ physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe³⁺) was in the lattice of TiO₂ and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe³⁺ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO₂ materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO₂) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO₂ (zero-iron TiO₂) and Aeroxide^® TiO₂ P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO₂ under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

Antibiotic residues in aquatic environment have the possibility to induce resistance in environmental bacteria, which ultimately might get transferred to pathogens making treatment of diseases difficultand poses a serious threat to public health. If antibiotic residues in the environment can be eliminated or reduced, it has the possibility to contribute antibiotic resistance. Towards this objective, water containing ciprofloxacin was treated with sunlight assisted photocatalysis using Fe doped ZnOnanoparticles for assessing the degradation potential of this system.Parameters like pH, temperature, catalytic dosage were assessed for the optimum performance of the system. To evaluate degradation of ciprofloxacin,both spectrophotometricas well as microbiological (loss of antibiotic activity)methods were employed. 100 mg/L Fe doped ZnO nanoparticle catalyst and sunlight intensity of 120,000–135,000 lux system gave optimum performance at pH 9 at 30 °C and 40 °C. At these conditions spectrophotometric analysis showed complete degradation of ciprofloxacin (10mg/L) by 210 min. Microbiological studies showed loss of antibacterial activity of the photocatalytically treated ciprofloxacin containingwater against Staphylococcus aureus (10⁸ CFU) in 60 min and for Escherichia coli (10⁸ CFU) in 75 min. Thedeveloped system, thus possess a potential for treatment of antibiotic contaminated waters for eliminating/reducing antibiotic residues from environment.

The electronic structure of 7/9-AGNR superlattices with up to eight unit cells has been studied by means of state of the art Density Functional Theory (DFT) and also by two model Hamiltonians, the first one including only local interactions (Hubbard model, Hu) while the second one is extended to allow long-range Coulomb interactions (Pariser, Parr and Pople model, PPP). Both are solved within mean field approximation. At this approximation level, our calculations show that 7/9 interfaces are better described by spin non-polarized solutions than by spin-polarized wavefunctions. Consequently, both Hu and PPP Hamiltonians lead to electronic structures characterized by a gap at the Fermi level that diminishes as the size of the system increases. DFT results show similar trends although a detailed analysis of the density of states around the Fermi level shows quantitative differences with both Hu and PPP models. Before improving model Hamiltonians, we interpret the electronic structure obtained by DFT in terms of bands of topological states: topological states localized at the system edges and extended bulk topological states which interact between them due to the long-range Coulomb terms of Hamiltonian. After careful analysis of the interaction among topological sates, we find that the discrepancy between ab initio and model Hamiltonians can be resolved considering a screened long-range interaction that is implemented adding an exponential cutoff to the interaction term of PPP model. In this way, an adjusted cutoff distance λ = 2 allows a good recovery of DFT results. In view of this, we conclude that the correct description of the density of states around the Fermi level (Dirac point) needs the inclusion of long-range interactions well beyond Hubbard model but not completely unscreened as is the case for the PPP model.

This review contains a popular presentation of the history of carbon nanostructure discovery, a short description of the main approaches to production and investigation of such objects and consideration of the most perspective ways of their applied usage.

The effect of graphene oxide (GO) on mechanical strengths and durability of cement composites has been studied by preparing GO-modified cement mortars. Thermogravimetric analysis (TGA) and nuclear magnetic resonance (29Si MAS-NMR) were performed on the cement paste to research the influence of GO on the hydration process and chain structure of calcium-silicate-hydrate (C-S-H) gels. In addition, mechanical strength test, such as compressive and flexural, were performed on cement mortars. The addition of GO at 0.05 wt.% (by weight of cement) increased the compressive strength by 9.02% after 28 days. Furthermore, the flexural strength of cement mortars with 0.05 wt.% GO and superplasticizer (SP) after 7 and 28 days increased by 12.26% and 21.86%, respectively, compared with reference mortar. At the same time, the effect of GO proved to be more significant and effective in the durability tests, suggesting that GO can enhance the microstructure through hydration products to create a highly cross-linked micro structure.

In nowadays, the synthesis of new composite nanomaterials based on graphene oxide (GO) modified with cellulose and its derivatives, as well as nanocellulose, is an important direction and contributes to solve many problems in various fields such as: nanotechnology, information technology, medicine, high-dielectric materials and nanoelectronics. In this work, for the first time, for the production of GO and its membrane with carboxymethylcellulose (CMC), local Kazakhstan “Ognevsky” graphite was used as the initial raw material. In this regard, the preparation of nanocomposites of GO modified with cellulose derivatives, including CMC, attracts great interest from scientists and expands its field of practical application due to the amazing changes of physicochemical properties. In the work, the GO obtained by the Hummers method was modified by CMC, with following study of its physicochemical, structural and electrical characteristics. The GO/CMC membrane was synthesized by mixing 1% GO with crushed solid mass of CMC (0.03 g; 0.06 g; 0.15 g) and then was processed by ultrasound. The surface morphology of the GO/CMC membrane were studied using Scanning electron microscopy (SEM). It has been established that with an increasing in the mass of CMC (0.03 g; 0.06 g; 0.15 g), polymerization of CMC occurs on the surface of GO nanosheets. Cross-sectional micrographs of GO/CMC show the formation of sandwich-like layered structures.

Integrated photonic devices operating via optical nonlinearities offer a powerful solution for all-optical information processing, yielding processing speeds that are well beyond that of electronic processing as well as providing the added benefits of compact footprint, high stability, high scalability, and small power consumption. The increasing demand for high-performance nonlinear integrated photonic devices has facilitated the hybrid integration of novel materials to address the limitations of existing integrated photonic platforms, such as strong nonlinear optical absorption or an inadequate optical nonlinearity. Recently, graphene oxide (GO), with its large optical nonlinearity, high flexibility in altering its properties, and facile fabrication processes, has attracted significant attention, enabling many hybrid nonlinear integrated photonic devices with improved performance and novel capabilities. This paper reviews the applications of GO to nonlinear integrated photonics. First, an overview of GO’s optical properties and the fabrication technologies needed for its on-chip integration is provided. Next, the state-of-the-art GO nonlinear integrated photonic devices are reviewed, together with comparisons of the nonlinear optical performance of different integrated platforms incorporating GO. Finally, the challenges and perspectives of this field are discussed.

A facile iridium/graphene-catalyzed methodology providing an efficient synthetic route for C-N bond formation is reported. This catalyst can directly promote the formation of C-N bonds, without pre-activation steps, and without solvents, alkalis and other additives. This protocol provides a direct N -alkylation of amines using a variety of primary and secondary alcohols with good selectivity and excellent yields. Charmingly, the use of diols resulted in intermolecular cyclization of amines, and such products are privileged structures in biologically active compounds. Two examples illustrate the advantages of this catalyst in organic synthesis: the tandem catalysis to synthesize hydroxyine, and the intermolecular cyclyzation to synthesize cyclizine. Water is the only by-product, which makes this catalytic process sustainable and environmentally friendly.

The selectivity in the simultaneous detection of ascorbic acid (AA), dopamine (DA), and uric acid (UA) has been an open problem in the biosensing field. Many surface modification methods were carried out for glassy carbon electrodes (GCE), including the use of graphene oxide and amino acids as a selective layer. In this work, molecular dynamics (MD) simulations were performed to investigate the role of serine oligomers on the selectivity of the AA, DA, UA analytes. Our models consisted of a graphene oxide (GO) sheet under a solvent environment. Serine tetramers were added into the simulation box and were adsorbed on the GO surface. Then, the adsorption of each analyte on the mixed surface was monitored from MD trajectories. It was found that the adsorption of AA was preferred by serine oligomers due to the largest number of hydrogen-bond forming functional groups of AA, while UA was the least preferred due to its highest aromaticity. Finally, the role of hydrogen bonds on the electron transfer selectivity of biosensors was discussed with some previous studies.

Two-dimensional silicon allotrodes– also called Sinicene– have recently experienced intensive scientific research interest due to their unique electrical, mechanical, and sensing characteristics. A novel silicene based nano-material has been enticed great amenities, partially because of its uniformity with graphene. Silicene is a highly sensitive for numerous sensors based on molecular sensing as pH sensor, gas sensor, ion sensor and biosensing are Deoxyribonucleic acid (DNA) nucleobase sensor, photonic sensor, cell-based biosensor, glucose sensor, and bioelectric nose sensor. Nowadays genetic research based on DNA hybridization, which is a vital tools for sensing material and it has various detection methods. Among of them, the detection method is frequency readout used to a label-free detection of DNA hybridization. In this paper we have compared the graphene and silicene quantum capacitance that has been proposed for a DNA hybridization detection method on wireless readout. These method shows, the strands of mismatched and complementary DNA have in different range of frequency to identify output efficiency. With respect to DNA concentration the output of silicene is almost sharply linear than graphene. In addition of field effect transistor, silicene opens a new opportunities due to its band gap whereas graphene indicates zero band gap. It can be stated that silicene is much more reliable as well as much stronger than multi-layered graphene.

In order to obtain higher thermoelectric and mechanical properties in non-polar thermoplastic vulcanizates (TPVs), the Butyl rubber/Polypropylene (TPVs)/hydroxylated graphene (HGE) composites with nanosheet network were prepared through masterbatch technique and based on thermodynamic calculations, using polypropylene-graft-maleic anhydride (PP-MA) as a compatibilizer. The FTIR and Raman spectra revealed the introduced maleic anhydride group on PP-MA can form strong interfacial interaction with hydroxyl-containing functional groups on HGE. Morphology study indicated the rubber particles in the composites occupied the most volume of the PP phase, as expected to hinder the aggregation of HGE and form the effective nanosheet network. The nanosheet network can be combined with the IIR cross-linked particles during the dynamic vulcanization process to improve the interface bonding between PP and IIR, thus increasing the tensile strength of TPVs. When the content of HGE reached the percolation threshold (2 wt.%), the nanosheet network of HGE was formed, and the AC conductivity, dielectric permittivity and thermal conductivity increased sharply. The prepared TPVs/HGE nanocomposites have significantly improved in mechanical properties, thermal properties and dielectric properties, which provides a guarantee for their potential application as multifunctional TPVs polymers.

Graphite nanoplatelets (GNPs) were produced from flake graphite that had been immersed in isopropyl alcohol solution (70%) and converted to powder form in an ultrasonic bath (5 h, room temperature). Scanning and transmission electron microscopy, X-ray diffractometry, and Raman spectroscopy identified 120-nm-thick GNP crystallites and 0.5–21 µm plates with different areas and shapes. Extensive exfoliation was observed by transmission electron microscopy with abundant multilayer and some monolayer GNPs. X-ray diffractometry confirmed 43 GNP layers along the c-axis. Raman spectroscopy indicated well-defined GNPs with few defects and no oxide content. Rietveld analysis indicated a GNP crystal lattice with stacks of parallel two-dimensional graphene layers and tightly bound hybridized carbon atoms stacked in a translational …ABAB… sequence in hexagonal rings.

The present study focuses on the synthesis, characterization, and investigation of a p-n heterojunction photocatalysis. Titanium dioxide (TiO2) can’t alone induce the photocatalytic water splitting due to its wide bandgap, which decreases its catalytic activity in the visible light. To make redshift of absorptivity for the TiO2, Nickel (Ni)-doped Graphene (rGO) supported TiO2 was synthesized. Several characterization techniques have been employed to validate the composition and the light absorption ability of the prepared photocatalysts including TEM, SEM, EDS, XRD, XPS, and UV-Vis spectroscopy. The characterization revealed successful doping of the Ni and TiO2 on the rGO nanosheet. Moreover, the UV-Vis spectroscopy indicated a significant shift of light absorption toward the visible spectrum. The photon-induced evolution of H2 was remarkably enhanced using the prepared Ni-rGO/TiO2 nanocomposite. Furthermore, the optimum ratio of rGO: TiO2: Ni in the hybrids was 10:1:4, while the higher Ni ratio would decrease the photocatalytic activity. The stability of the photocatalyst was also verified during 8 cycles of photocatalytic reactions. The kinetic study revealed the nature of the integrated reaction and the controlling step governing the reaction sequence. .

In the present work freezing and melting characteristics of water seeded with chemically functionalized graphene nano-platelets in a vertical cylindrical capsule was experimentally studied. The volume percentage of functionalized graphene nano-platelets was varied from 0.1% to 0.5% with an interval of 0.1%. The stability of the synthesised samples were carried out by zeta potential distribution. The thermal conductivity of the nanocomposite samples were experimentally measured using transient hot wire method. A maximum enhancement of ~24% in the thermal conductivity was observed for the 0.5% volume percentage in the liquid state while a ~53% enhancement in the solid state. Freezing and melting behaviour of water dispersed with graphene nanoplatelets were carried out using a cylindrical stainless steel capsule in a constant temperature bath. The bath temperatures considered for studying freezing characteristics were considered to be −6 °C and −10 °C, while to study the melting characteristics the bath temperature was set as 31 °C and 36 °C. The freezing and melting time decreased for all the test conditions when the volume percentage of GnP increased. The freezing rate was enhanced by ~ 43% and ~32% for the bath temperatures of −6 °C and −10 °C respectively at 0.5 vol % of graphene loading. The melting rate was enhanced by ~42% and ~63% for the bath temperature of 31 °C and 36 °C respectively at 0.5 vol % of graphene loading.

This review provides informations and details for the fabrication of biosensors that are composed from lipid membranes and have been utilized and applied to rapidly detect food toxic compounds, environmental pollutants and analytes of clinical interest. Biosensors based on polymeric lipid membranes have been used to rapidly detect a wide range of these analytes and offer several advantages such as fast response, high sensitivity and selectivity, can be portable for in the field applications, and small size. A description of the construction of these devices and their applications for the rapid detection of food toxic substance, environmental pollutants and analytes of clinical interest is provided in this review.

Graphene-based nanomaterials (GNMs), including graphene, graphene oxide, reduced graphene oxide, and graphene quantum dots, may have direct anticancer activity or be used as nanocarri-ers for antitumor drugs. GNMs usually enter tumor cells by endocytosis and can accumulate in lysosomes. This accumulation prevents drugs bound to GNMs from reaching their targets, sup-pressing their anticancer effects. A number of chemical modifications are made to GNMs to facili-tate the separation of anticancer drugs from GNMs at low lysosomal pH and to enable lysosomal escape of drugs. Lysosomal escape may be associated with oxidative stress, permeabilization of the unstable membrane of cancer cell lysosomes, release of lysosomal enzymes into the cytoplasm, and cell death. GNMs can prevent or stimulate tumor cell death by inducing protective autopha-gy or suppressing autolysosomal degradation, respectively. Furthermore, because GNMs prevent bound fluorescent agents from emitting light, their separation in lysosomes may enable tumor cell identification and therapy monitoring. In this review, we explain how the characteristics of the lysosomal microenvironment and the unique features of tumor cell lysosomes can be exploited for GNM-based cancer therapy.

PEDOT:PSS (polyethylene dioxythiophene:polystyrenesulfonate) is a commonly used hole injec-tion layer (HIL) in optoelectronic devices due to its high conductive properties and work function. However, the acidic and hygroscopic nature of PEDOT:PSS can be problematic for device stability over time. To address this issue, in this study, we have demonstrated the potential of an organic-inorganic hybrid HIL, by incorporating solution-processed WOx nanoparticles (WOx NPs) into the PEDOT:PSS mixture. This hybrid solution was found to have a superior hole transport ability and low Ohmic contact resistance, contributing to higher brightness (~62 000 cd m-2) and current efficiency (13.1 cd A-1) in the manufactured quantum-dot based light-emitting diodes (QLEDs). In addition, the resulting devices achieved a relative operational lifetime of 7,071 hours, or approxi-mately twice that of traditional QLEDs with PEDOT:PSS HILs. The proposed method is an un-complicated, reliable and low-cost way to achieve long operational lifetimes without sacrificing efficiency in optoelectronic devices.

This study investigates the role of oxygen vacancy on Fe-doped CeO₂ catalyst activity for soot oxidation. The oxygen vacancy was assessed through Ce³⁺ content. The Fe content was varied between 0 and 30% for two catalyst preparation methods, co-precipitation (CP) and solution combustion synthesis (SCS). X-ray photoelectron spectroscopy indicates that ceria exists as both Ce₄₊ and Ce₃₊, while iron is present only as Fe₃₊. The catalyst’s activity was evaluated by ignition (T10) and combustion (T50) temperatures using thermogravimetric analysis. Optimum Fe contents yielding the highest activity were found to be 10% and 5% for CP and SCS catalysts, respectively. The surface area and morphology have shown moderate effect on catalyst activity, because catalytic soot oxidation involves solid-solid contact. More importantly, regardless of the fabrication method, it was found that Ce₃₊ content, which is closely related to oxygen vacancies, plays the most important role in affecting the catalyst activity.

Ga doped ZnO thin films were formed by the Ultrasonic Chemical Spray Pyrolysis method onto substrates using zinc acetate and gallium (III) nitrate hydrate as precursors. The structural, optical, surface and electrical properties were studied as a function of increasing Ga doping concentration from 0 to 6 at %. Structural studies were shown polycrystalline with a hexagonal crystal structure. The transparency in the visible range was around 85% for thin film deposited using 6 at % Ga doping. With the aim of determining surface images and surface roughness of the films atomic force microscope images were taken. Ga doping of ZnO thin films could markedly decrease surface roughness. Electrical resistivity was determined by four point method. The resistivity 2.0% Ga doped ZnO film was the lowest resistivity of 1.7 cm. In the photoluminescence measurements of the films, existence of UV and defect emission band was observed. As a result, Ga doped ZnO films have advanced properties and promising materials for solar cells.

Modeling and design of fiber lasers facilitate the process of their practical realization. Of particular interest during the last few years is the development of lanthanide ion-doped fiber lasers which operate at wavelengths exceeding 2000 nm. There are two main host glass materials considered for this purpose, namely fluoride and chalcogenide glasses. Therefore, this study concerns comparative modeling of fiber lasers operating within the infrared wavelength region beyond 2000 nm. In particular, the convergence properties of selected algorithms, implemented within various software environments, are studied with a specific focus on the central processing unit (CPU) time and calculation residual. Two representative fiber laser cavities are considered: one is based on a chalcogenide-selenide glass step-index fiber doped with trivalent dysprosium ions whilst the other is a fluoride step-index fiber doped with trivalent erbium ions. The practical calculation accuracy is also assessed by comparing directly the results obtained from the different models.