This paper presents an exact solution to the Timoshenko beam theory (TBT) for first-order analysis, second-order analysis, and stability. The TBT covers cases associated with small deflections based on shear deformation considerations, whereas the Euler–Bernoulli beam theory (EBBT) neglects shear deformations. Thus, the Euler–Bernoulli beam is a special case of the Timoshenko beam. The moment-curvature relationship is one of the governing equations of the EBBT, and closed-form expressions of efforts and deformations are available in the literature. However, neither an equivalent to the moment-curvature relationship of EBBT nor closed-form expressions of efforts and deformations can be found in the TBT. In this paper, a moment-shear force-curvature relationship, the equivalent in TBT of the moment-curvature relationship of EBBT, was presented. Based on this relationship, first-order and second-order analyses were conducted, and closed-form expressions of efforts and deformations were derived for various load cases. Furthermore, beam stability was analyzed and buckling loads were calculated. Finally, first-order and second-order element stiffness matrices were determined.

Music therapy has served as complementary and alternative medicine for various neurological disorders. Five Phases Music Therapy (FPMT) employs the theory of five phases and five music scales or tones (宫Gong (do), 商Shang (ri), 角Jue (mi), 徵Zhi (so) and 羽Yu (la)) to analyze and treat mind-body illness. In Chinese Medicine (CM), the five music scales are used to connect the human body and the universe, interpret personalities and constitution and analyze the influences of climatic changes on health. FPMT has a self-contained theory and routine of practice application. Large amounts of clinical and fundamental reports have been available and clinical benefits have been obtained. However more systemic clinic research esp. evidence-based and random controlled trials must be performed to validate and optimize its routines and biological and neurological mechanism must be further explored. It’s reasonable to believe that the effective music therapy will attract more attention from the world outside China with the introduction of FPMT.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

The aim of this work was to determine if the development of low-cost or no-cost finite element analysis (FEA) software has advanced to the point where it can be used in place of trusted commercial FEA packages for linear static structural analyses using isotropic material models. Nonlinear structural analysis will be covered in a separate paper. Several suitable packages were identified, these underwent a process of systematic elimination when they were unable to meet the minimum imposed qualitative criteria. Three packages were chosen to be subjected to performance benchmarking, namely: Code_Aster/Salome Meca; Mecway and Z88 Aurora. SimScale, a browser-based analysis package was included as well because it met all the baseline criteria and has the potential to offer a completely cloud-based approach to computer aided engineering, potentially reshaping the way an engineering business views its operational capabilities. This paper presents the test cases and simulation results for packages that fall under the linear static structural analysis type.

The Wind Energy Conversion System (WECS) plays an inevitable role across the world. In particular, the attention for Permanent Magnet Synchronous Generators (PMSGs) connected with wind farm is popular. This paper deals with the literature review that describes the recent advances, progresses and innovatory trends on PMSGs for WECS. Comparison between geared and direct-driven conversion systems and the classification of electrical machines used in WECS are discussed. A detailed analysis on the design aspects considering various topologies of PMSGs are encompassed in the literature. The PMSG design and optimization problems are solved by field computation techniques and optimized by using Soft Computing (SC) techniques .The three-dimensional, finite element software platform for the analysis and design of PMSGs is discussed. This paper also deals with the interdisciplinary modeling, analysis, and optimization of PMSG using Finite Element Analysis (FEM) and SC techniques. Finally, PMSGs are reviewed and compared for further exploration.

This study presents a new form of velocity distribution in laminar liquid flow in rectangular microchannels using the eigenfunction expansion technique. Darcy friction factor and Poiseuille number are also obtained analytically. Due to the symmetry of the solutions, the effects of changing the aspect ratio from 0 to ∞ are also discussed. Using finite element method (FEM), the obtained analytical results are further compared with the 3D numerical simulations for the rectangular microchannels with different range of aspect ratio and pressure gradient, and excellent agreements were found. These findings provide additional insights in interpreting the results of the pressure-driven flows in finite aspect ratio microchannels, in which very precise comparison with the macroscale theory is crucial.

The purpose of this work was analysing the compaction of a cohesive material using different DEM simulators to determine the equivalent contact models and identify how some parameters of the simulations affect the compaction results (maximum force and compacts appearance) and computational costs. For that purpose, three cohesion contact models were tested (‘linear cohesion’ in EDEM; ‘SJKR’ and ‘SJKR2’ in LIGGGHTS). The influence of the particle size distribution (PSD) on the results was also investigated. Further assessments were performed on the effect of selecting different timesteps, using distinct conversion tolerances for exporting the 3D models to STL files and moving the punch with different speeds. Consequently, it was possible to determine that a timestep equal to a 10% Rayleigh timestep, a conversion tolerance of 0.01 mm and a punch speed of 0.2 m/s are adequate for simulating the compaction process using the contact models in this work. In addition, the results determined that the maximum force was influenced by the PSD because of the rearrangement of the particles. The PSD was also related to the computational cost because of the number of simulated particles and their sizes. Finally, an equivalence was found between the linear cohesion and SJKR2 contact models

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

Polymer nanocomposites are composed of polymer materials reinforced with nano fillers. In the present study the effective thermal conductivity of the composites filled with nanofillers has been investigated using commercially available finite element software ABAQUS 6.11. The nanofillers used were alumina particles and multi-walled carbon nanotubes (MWNTs) and the matrix was considered to be made of epoxy. For the analysis 2D and 3D Representative Volume Elements (RVEs) were generated using Random Sequential Adsorption (RSA) algorithm using MATLAB and Python scripts. Thermal conductivity was found out for 2D and 3D RVEs for different area and weight fractions respectively. Two different shapes of the alumina nanoparticles were considered: spherical (circular) and ellipsoidal (elliptical) for 3D (2D) analysis. It was found that the thermal conductivity was increased with the addition of nanofillers. The increase in thermal conductivity was approximately same for both types of inclusions at corresponding area or weight fractions in 2D or 3D analysis. The results showed that addition of MWNTs to the composites lead to a significant increase in thermal conductivity than spherical or ellipsoidal inclusions.

In this paper, the seven traditional models of PV modules are reviewed comprehensively to find out the appropriate model to be reliable. All the models are validated using the Matlab code and make a graphical comparison. The accuracy and convergence of each model are evaluated using data of manufactured PV panels. Then, a novel model is proposed showing its consistent performance. The most three key parameters of single-diode model are self revised to adapt to various type of PV modules. This new method is verified in three types of PV panels' data measured by National Renewable Energy Laboratory (NREL), US. The validated data show promising results when the error RMSEs' range of the proposed model is under 0.36.

No doubt pollution is a global problem which must be holistically tackled. In doing this, adequate knowledge of the sources of pollution is important, therefore the aim of this paper is to review source apportionment with reference to top-down and bottom-up methods. In this paper, dispersion modeling, emissions inventory, and sampling methods were discussed. Also, analytical methods involved in top-down source apportionment were mentioned. The two techniques are needed to evaluate pollutants and their sources. Based on these two approaches, pollution control strategy would be developed and decisions can be made in deciding the right approach to solve or reduce the pollution problems.

Concrete-filled steel columns have been extensively used in the world due to having all suitable characteristics of concrete and steel, more ductility, increasing concrete confinement using steel wall, large energy-absorption capacity and appropriate fire behavior. In present paper, concrete-filled steel square columns have been simulated under the influence of blast load using ABAQUS software. These responses will be compared for scaled distances based on the distance to source and weight of explosive material. As result, it can be seen that although concrete deformation has been restricted using steel tube, but inner layer of concrete has been seriously damaged and column displacement will be decreased by increasing scaled distance. We also concluded that concrete-filled steel columns have high ductility and blast resistance.

A common reactor type in the chemical and process industry is the fixed-bed reactor. Accurate modeling can be achieved with particle-resolved Computational Fluid Dynamic (CFD) simulations. However, the underlying bed morphology plays a paramount role. Synthetic bed-generation methods are much more flexible and faster than image-based approaches. In this study, we look critically at the two different bed generation methods: Discrete Element Method (DEM) (in the commercial software STAR-CCM+) and the rigid-body model (in the open-source software Blender). The two approaches are compared in terms of synthetically generated beds with experimental data of overall and radial porosity, particle orientation, as well as radial velocities. Both models show accurate agreement for the porosity. However, only Blender shows similar particle orientation than the experimental results. The main drawback of the DEM is the long calculation time and the shape approximation with composite particles.

Due to the demands of personal travels and entertainments, light airplanes and small business aircrafts are developing rapidly. Light airplane structure is simple; however, it lacks crashworthiness design, especially the considerations on the impact of energy absorption. Therefore, in an event of accident, significant damage to passengers will be usually incurred. Airplanes made of composite materials structurally have high specific strength and good aerodynamic configuration. These materials have become the primary choice for new airplane development. This study mainly explores the topology optimization analysis of the light aircraft’s cockpit made of carbon fiber reinforced composites. This paper compares the compression amounts in the original models of composite material and aluminum alloy fuselages with the models after optimization during the crash-landing, in order to investigate the safety of fuselages made of different materials after structural optimization under the dynamic crashing. This study found that the energy absorbed by the aluminum alloy fuselage during crash-landing is still higher than that by the carbon fiber reinforced composites fuselage. On the other hand, the aluminum alloy fuselage after topology optimization could have an energy absorption capability enhanced by 40%, as compared to the that of the original model of aluminum alloy fuselage.

This paper presents an approach to the Euler-Bernoulli beam theory (EBBT) using the finite difference method (FDM). The EBBT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally, the finite difference approximations are derived based on fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection curve; the FOPH is made for the fourth and third derivative of the deflection curve while the SOPH is made for its second and first derivative. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, the FOPH was made for all of the derivatives of the deflection curve, and additional points were introduced at the beam’s ends and positions of discontinuity (concentrated loads or moments, supports, hinges, springs, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. First-order analysis, second-order analysis, and vibration analysis of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis). Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid. Further research will be needed to investigate polynomial refinements (higher-order polynomials such as fifth-order, sixth-order…) of the deflection curve; the polynomial refinements aimed to increase the accuracy, whereby non-centered finite difference approximations at beam’s ends and positions of discontinuity would be used.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

Transient analysis of gas flow in pipeline was studied. Finite Element Method based on ANSYS FLOTRAN was used to account for changes in pressure, temperature and flow rate. Compressibility factor function of temperature and pressure was considered. For non-isothermal transient results, the pressure and the flowrate gave wave propagation as a result of slow transients created by demand condition at the outlet end of custody transfer. Results obtained were in agreement with the demand restrictions at the outlet end of custody transfer indicating that the predictions are accurate and reliable. The results demonstrated that the Finite Element Method gave accurate prediction of pressure, temperature and flowrate in transient gas studies. For steady state non-isothermal model, results showed that the magnitude of the average pressure drop was higher when pressure was predicted with constant compressibility factor, but the same average pressure drop was reduced when the pressure was predicted with variable compressibility factor, z. Since compressibility factor is a function of temperature and pressure, the above findings signifies that in the case when gas temperature does not stabilize, the prediction of pressure with isothermal model and constant compressibility factor will lead to significant errors.

During HVDC earth return operation systems, a high magnitude current will be injected into soil through earth electrode, the potential on the surface would change widely and produce unfavorable effects on the AC systems around. This paper presents an effective finite element method (FEM) coupling electric field with thermal field to evaluate the electrical field induced by the injected DC current. Firstly, owe to the characteristic of FEM, this method can consider arbitrary soil and earth electrode structure. Secondly, by setting the electrical and thermal parameters of soil as a function of temperature at the same time, the dynamic coupling process of electric field and thermal field is simulated accurately. Thirdly, to deal with the singular point in FEM subdivision and the huge computation in traditional three-dimensional FEM, the FEM coupling 2-D earth electrode with 3-D soil based on "shell" theory is introduced. Finally, based on the suggested method, the effect of abnormal resistance region (ARR) near DC earth electrode on electric field distribution is analyzed.

Personality is the most critical feature that tells us about an individual. It is the collection of the individual’s thoughts, opinions, emotions and more. Personality detection is an emerging field in research and Deep Learning models have only recently started being developed. There is a need for a larger dataset that is unbiased as the current dataset that is used is in the form of questionnaires that the individuals themselves answer, hence increasing the chance of unconscious bias. We have used the famous stream-of-consciousness essays collated by James Pennbaker and Laura King. We have used the Big Five Model often known as the five-factor model or OCEAN model. Document-level feature extraction has been performed using Google’s word2vec embeddings and Mairesse features. The processed data has been fed into a deep convolutional network and a binary classifier has been used to classify the presence or absence of the personality trait. Hold- out method has been used to evaluate the model, and the F1 score has been used as the performance metric.

The present study aims to develop an efficient numerical method for computing the diffraction and radiation of water waves with horizontal long cylindrical structures, such as floating breakwaters. A higher-order scheme is used to discretize geometry of the structure as well as the relevant physical quantities. As the kernel of this method, Wehausen’s free-surface Green function is calculated by a newly-developed Gauss-Kronrod adaptive quadrature algorithm after elimination of its Cauchy-type singularities. To improve computational efficiency, a Chebyshev approximation approach is applied to a fast calculation of the Green function that needs evaluation thousands of times. In addition, OpenMP parallel technique is used to the formation of influence coefficient matrix, which significantly reduces CPU time. Finally, computations are performed on wave exciting forces and hydrodynamic coefficients for the long cylindrical structures, either floating or submerged. Comparison with other numerical and analytical methods demonstrates good performance of the present method.

Estimating the vehicle crashworthiness parameters experimentally is expensive and time consuming. For these reasons different modelling approaches are utilized to predict the vehicle behaviour and reduce the need for full-scale crash testing. The earlier numerical methods used for vehicle crashworthiness analysis were based on the use of lumped parameters models (LPM), a combination of masses and nonlinear springs interconnected in various configurations. Nowadays, the explicit nonlinear finite element analysis (FEA) is probably the most widely recognized modelling technique. Although informative, finite element models (FEM) of vehicle crash are expensive both in terms of man-hours put into assembling the model and related computational costs. A simpler analytical tool for early analysis of vehicle crashworthiness could greatly assist the modelling and save time. In this paper a simple piecewise LPM composed of a mass-spring-damper system, is used to estimate the vehicle crashworthiness parameters, focusing on the dynamic crush and the acceleration severity index (ASI). The model is first calibrated against a full-scale crash test and a FEM, post-processed with the LS-DYNA software, at an impact velocity of 56 km/h. The genetic algorithm is used to calibrate the model by estimating the piecewise lumped parameters (stiffness and damping of the front structure of the vehicle). After calibration, the LPM is applied to a range of velocities (40, 48, 64 and 72 km/h). The predictions for crashworthiness parameters from the LPM were compared with the predictions from the FEA and the results are much similar. It is shown that the LPM can assist in crash analysis, since LPM has some predictive capabilities and requires less computation time in comparison with the explicit nonlinear FEA.

Structural deformations are one of the most significant factor that affects machine tool (MT) positioning accuracy. These induced errors are complex to be represented by a model, nevertheless they need to be evaluated and predicted in order to increase the machining performance. This paper presents a novel approach to calibrate a machine tool in real-time, analyzing the thermo-mechanical errors through Fibre Bragg Grating (FBG) sensors embedded in the MT frame. The proposed configuration consists of an adaptronic structure of passive materials, Carbon Fibre Reinforced Polymers (CFRP), equipped by FBG sensors that are able to measure in real-time the deformed conditions of the frame. By using a proper thermo-mechanical kinematic model, the displacement of the end effector may be predicted and corrected when it is subjected to external undesired factors. By starting from a set of FE simulations to develop a model able to describe the MT structure stresses, a prototype has been fabricated and tested. The scope was to compare the numerical model with the experimental tests using FBG sensors. The experimental campaign has been performed varying the structure temperature over time and measuring the tool tip point (TTP) positions. The obtained results showed a substantial matching between the real and the predicted position of TTP confirming the effectiveness of the proposed calibration system.

This paper presents an approach to the Timoshenko beam theory (TBT) using the finite difference method (FDM). The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. The model developed in this paper consisted of formulating differential equations with finite differences and introducing additional points at the beam’s ends and at positions of discontinuity (concentrated loads or moments, supports, hinges, springs, brutal change of stiffness, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends. Moreover, grid points with variable spacing were considered, the grid being uniform within beam segments. First-order, second-order, and vibration analyses of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis, vibration analysis). Finally, a direct time integration method (DTIM) was presented; the FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid.

A novel fiber optic sensing technology for high frequency dynamics detection is proposed in this paper, specifically tailored for structural health monitoring applications based on strain wave analysis, including both passive impact identification and active Lamb wave monitoring. The sensing solution relies on a fiber optic-based interferometric architecture associated to an innovative coherent detection scheme, which retrieves in a completely passive way the high-frequency phase information of the received optical signal. The optical fiber can be arranged into different configurations in order to meet the requirement of the specific application, the sensor sensitivity being maximized while still ensuring a limited gauge length if a local measure is required. For the active Lamb wave monitoring, this results in a sensing fiber arranged in multiple loops glued on an aluminum thin panel in order to increase the phase signal relative only to the sensing points of interest. Instead, for passive impact identification, the sensitivity is simply increased by exploiting a longer gauge length glued to the structure. The fiber optic coherent (FOC) sensor detects the strain waves emitted by a piezoelectric transducer placed on the aluminum panel or generated by an impulse hammer, respectively. The FOC sensor measurements have been compared with both a numerical model based on Finite Elements and traditional piezoelectric sensors, confirming a very good agreement between experimental and simulated results for both the active and passive impact monitoring scenarios.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

The geometry of Poincare disk itself is interpreted without any mapping to dierent spaces. Our approach might be one of the shortest and is intended for educational contribution.

In the last decades synthetic jet actuators have gained much interest among the flow control techniques due to their short response time, high jet velocity and absence of traditional piping, that matches the requirements of reduced size and low weight. A synthetic jet is generated by the diaphragm oscillation (generally driven by a piezoelectric element) in a relatively small cavity, producing periodic cavity pressure variations associated with cavity volume changes. The pressured air exhausts through an orifice, converting diaphragm electrodynamic energy into jet kinetic energy. This review paper faces the development of various lumped-element models (LEMs) as practical tools to design and manufacture the actuators. LEMs can quickly predict device performances such as the frequency response in terms of diaphragm displacement, cavity pressure and jet velocity, as well as the efficiency of energy conversion of input Joule power into useful kinetic power of air jet. The actuator performance is analyzed also by varying typical geometric parameters such as cavity height and orifice diameter and length, through a suited dimensionless form of the governing equations. A comprehensive and detailed physical modeling aimed to evaluate the device efficiency is introduced, shedding light on the different stages involved in the process. Overall, the influence of the coupling degree of the two oscillators, the diaphragm and the Helmholtz’s one, on the device performance is discussed throughout the paper.

An effective method to inspect inaccessible nuclear power facility by interface wave which propagate along the shrink fit boundary of reactor head is proposed in this study. Reactor head is relatively thick to inspect from the outside of reactor by conventional ultrasonic testing. The proposed interface wave can propagate a long distance from the fixed transducer position. The inside of nuclear reactor is limited to access due to the high radiation, so transducers are located at outside of nuclear facility and interface wave propagates into the nuclear reactor for defect detection. The numerical simulation and experiments were carried out to validate the effectiveness of the proposed interface wave inspection method. Various defect cases simulating field failures are also presented with satisfactory detectability by the proposed technique with the features for defect classification.

Although Cucurbita pepo is one of the most variable species of the plant kingdom, Zucchini morphotype has undergone intensive breeding that has led to a narrow genetic base making the crop vulnerable to pest and diseases. This vulnerability makes the knowledge of resistance genes of utmost importance. In this study, a data mining search of Zucchini summer squash genome database was conducted to identify and annotate members of the NBS-encoding gene family. In order to characterize the retrieved genes in detail, they have been studied in the bases of phylogenetic relationships, structural diversity, conserved protein motifs, gene duplications and promoter region analysis. Our study shows that the NBS-encoding gene family is relatively small in Zucchini (34 members, which are separated into non-TIR- and TIR-NBS-LRR subfamilies) with a significantly lower number of R-genes than in other species. Duplications have not played a major role in the expansion of this type of genes in C. pepo. Among the cis-regulatory elements presented in these sequences, six motifs are over-represented. These elements were reported to be involved in pathogens or plant stress induced responses. These results will contribute to the identification, isolation and characterization of candidate R-genes, thereby providing insight into NBS gene family evolution in the species.

As the demand for liquefied petroleum gas (LPG) continues to increase worldwide, more LPG facilities are being constructed. However, the design and manufacture of pressure vessels used to store dangerous liquids or pressurised fluids, such as LPG, has been a major cause of hazards, including explosions and leakage. In this study, we aim to address this issue by designing and analysing a vertical pressure vessel with a capacity of 10 m3 of pressurised LPG in accordance with the American Society of Mechanical Engineers (ASME) code. Safety is the primary concern in designing pressure vessels due to the potential risks posed by accidents. Therefore, the main objective of this project is to design a pressure vessel that is safe from failure. The vessel is cylindrical with two elliptical heads, two nozzles, a manway and four leg supports, and we used Autodesk Inventor Professional 2023 for geometric modelling and Inventor Nastran for FEA analysis. To investigate the displacements, deflections and Von-Mises stresses in the pressure vessel, we used the finite element method, and Autodesk Inventor Nastran was employed for the analysis. Our results showed that changes to the structure of the pressure vessel were needed to reduce stress in the structure. Specifically, the displacement showed an inverse relationship with the tank section shell thickness. Moreover, we observed that the factor of safety increased linearly with shell thickness. We carefully considered permissible pressures and determined the required wall thickness to ensure acceptable maximum stresses. Our results indicate that the design is safe from failure, and the highest stresses are experienced by the manway followed by the shell, while the heads, nozzles and legs support experienced the lowest stresses. We also performed a theoretical calculation for the entire model and checked the results to ensure they were within the acceptable limits. In summary, our study highlights the importance of designing pressure vessels in accordance with ASME codes to ensure safety and prevent hazards caused by improper design and manufacturing. By using the finite element method, we identified potential stress points in the pressure vessel and were able to make modifications to improve its safety.

Properties of time domain parameters of the vibration signal have been extensively studied for the fault diagnosis of rolling element bearings (REB). Parameters like kurtosis and Envelope Harmonic-to-Noise Ratio are most widely applied in this field and some important progress has been made. However, since only one-sided information is contained in these parameters respectively, problems still exist in practice when the signals collected are of complicated structure and/or contaminated by strong background noises. A new parameter, named Shock pulse index (SPI), is proposed in this paper. It integrates the mutual advantage of both parameters above and can help effectively identify fault related impulse components under the interference of strong background noises, unrelated harmonic components and random impulses. The SPI optimizes the parameters of Maximum Correlated Kurtosis Deconvolution (MCKD), which is used to filter the signals under consideration. Finally, the interested transient information contained in the filtered signal can be highlighted through demodulation with Teager Energy Operator (TEO). Fault related impulse components can therefore be extracted accurately. Simulations and experiment analyses verify the effectiveness and correctness of the SPI.

Rail impedance directly affects the transmission performance of track circuit . Considering the condition of earth stratification, for the difficult to calculate the rail impedance due to the semi-infinite integration interval and the oscillation of the integrand by using the Carson formula, The truncation method is proposed to divide the impedance formula is divided into definite integral and tail integral. The integral is approximated by the spline function, and the tail integral is calculated by using the exponential integral and Euler formula. Based on it, the rail impedance calculation formula of track circuit is obtained. The electromagnetic field model of track circuit with earth stratification is simulated by finite element method, and the correctness of the method is verified. Based on the formula, the influence of current frequency, soil depth and conductivity on rail impedance is studied. The relative error between the calculated results of rail impedance and the simulation results of finite element is within 5%. It can be seen that the formula has high accuracy and correctly reflects the law of rail impedance variation with current frequency, soil depth and resistivity. It provides a reliable reference for the theoretical calculation of rail impedance of track circuit.

The analytical method for the calculation of the properties of a bolted connection established by the structural Eurocodes proposes the T-stub as a component for the characterization of the tension and compression zones in moment joints. In this article, a review of the state of the art on the T-stub component is developed, where the works developed since it was initially defined, and from the perspectives of formulation, experimentation and numerical simulation are summarized and discussed. Additionally, possible future lines of work are proposed.

In this paper we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms⁻¹. We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy–conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength.

The purpose of this work is to optimize angular extrusion for sever plastic deformation of tubular specimens. A finite element model (FEM) was built in Deform-3D^® for three extrusion dies and analyzed. The dies were ECAP (135°), TCAP with external groove of 90° (denoted as TCAP-e) and TCAP with internal groove of 90° (denoted as TCAP-i). The analysis for process parameters (such as coefficient of friction-μ, die angles-ѱ and φ, temperature - T, and radius ratio-R) showed that TCAP-i was the optimal die in processing Al6063 tubes based on strain and load distribution of the model. The TCAP-i die model was further optimized for different parameters namely die angles, coefficient of friction, deformation ratio and temperature. The results showed that at constant process temperature of 25 °C, the optimal TCAP-i has the following parameters: φ₂=80⁰, Ѱ₁=30⁰, Ѱ₂=80⁰, Ѱ₃=30⁰, μ =0.4 and R =1.5.

This study investigates the failure of a roof with steel truss construction of a factory building in Tekirdag in North-western part of Turkey. The failure occurred under hefty weather conditions including thunderbolt, lightning strikes, heavy rain and fierce winds. In order to interpret the reason for the failure, the effects of different combinations of factors on the design and dimensioning of the roof are checked. Therefore, finite element analysis is performed several times under different assumptions and considering different factors aiming to determine the dominant ones that are responsible for the failure using the commercial software Abaqus (Dassault Systèmes, Vélizy-Villacoublay, France). Each loading condition gives out a characteristic form of failure. The scenario with the most similar form of failure to the real collapse is considered as the most likely scenario of failure. Also, the factors included in this scenario are expected to be the responsible factors for the partial collapse of the steel truss structure.

In the current study, the failure behavior of retrofitted steel structures was studied experimentally and theoretically with steel/CFRP double strap joints (DSJs) under quasi-static tensile loading. A series of DSJs with different bonding lengths are also considered and examined to experimentally assess the effective bond length. To predict the failure load values of the tested specimens, a new stress-based criterion, namely the point stress (PS) criterion is proposed. Although some theoretical predictive modelling for the strength between steel/CFRP joints under various loading conditions has been presented, in this work by using the new proposed approach, one can calculate rapidly and conveniently the failure loads of the steel/CFRP specimens. Furthermore, to assess the validity of the new proposed criterion, further experimental data on steel/CFRP DSJs available in the open literature are predicted using the PS criterion. Finally, it was found that a good agreement exists between the experimental results and the theoretical predictions based on the PS criterion.

To enable purposeful design and implementation of automated concrete technologies, precise assessment and prediction of the complex material flow at various stages of the process chain are necessary. This paper investigates the intermediate stage of the extrusion and deposition processes in extrusion-based 3D-concrete-printing, using a numerical model based on the Particle Finite Element Method (PFEM). In PFEM, due to the Lagrangian description of motion, remeshing algorithms and the alpha shape method are used to track the free surface during large deformation scenarios. The Bingham constitutive model was used for describing the rheological behaviour of fresh concrete. This model is validated by comparing the numerically predicted layer geometries with those obtained from laboratory 3D printing experiments. Extensive parametric studies were then conducted using the numerical simulation, delineating the influence of process and material parameters on the layer geometries, the dynamic surface forces generated under the extrusion nozzle and the inter-layer interactions.

In this study, we design a new refractive index sensor based on a metal–insulator–metal waveguide coupled with a notched ring and vertical rectangular resonators. We use the finite element method to study the propagation characteristics of the sensor. According to the calculation results, the transmission spectrum exhibits a typical Fano resonance shape. The phenomenon of Fano resonance is caused by the coupling between the wide spectrum and narrow spectrum. In the design, the wide spectrum signal is generated by the vertical rectangular resonator, while the narrow spectrum signal is generated by the notched ring resonator. In addition, we varied the structural parameters of the resonators and filled the structure with media of different refractive indices to study the sensing properties. The maximum achieved sensitivity of the sensor reached 1071.4 nm/RIU. The results reveal potential applications of the coupled system in the field of sensors.

With a large number of annotated non-coding RNAs (ncRNAs), repetitive sequences are found to constitute functional components (termed as repetitive elements) in ncRNAs that perform specific biological functions. Bioinformatics analysis is a powerful tool for improving our understanding of the role of repetitive elements in ncRNAs. This chapter summarizes recent findings that reveal the role of repetitive elements in ncRNAs. Furthermore, relevant bioinformatics approaches are systematically reviewed, which promises to provide valuable resources for studying the functional impact of repetitive elements on ncRNAs.

We use Matlab 3D finite element fluid flow/transport modelling to simulate localized wellbore temperature events of order 0.05-0.1oC logged in Fennoscandia basement rock at ~ 1.5km depths. The temperature events are approximated as steady-state heat transport due to fluid draining from the crust into the wellbore via naturally occurring fracture-connectivity structures. Flow simulation is based on the empirics of spatially-correlated fracture-connectivity fluid flow widely attested by well-log, well-core, and well-production data. Matching model wellbore-centric radial temperature profiles to a 2D analytic expression for steady-state radial heat transport with Peclet number Pe ≡ r0φv0/D (r0 = wellbore radius, v0 = Darcy velocity at r0, φ = ambient porosity, D = rock-water thermal diffusivity), gives Pe ~ 10-15 for fracture-connectivity flow intersecting the well, and Pe ~ 0 for ambient crust. Darcy flow for model Pe ~ 10 at radius ~ 10 meters from the wellbore gives permeability estimate κ ~ 0.02Darcy for flow driven by differential fluid pressure between least principal crustal stress pore pressure and hydrostatic wellbore pressure. Model temperature event flow permeability κm ~ 0.02Darcy is related to well-core ambient permeability κ ~ 1µDarcy by empirical poroperm relation κm ~ κ exp(αmφ) for φ ~ 0.01 and αm ~ 1000. Our modelling of wellbore temperature events calibrates the concept of reactivating fossilized fracture-connectivity flow for EGS permeability stimulation of basement rock.

Industrial manipulators and parallel robots are often used for tasks like drilling or milling, that require three translational, but only two rotational degrees of freedom (“3T2R”). While kinematic models for specific mechanisms for these tasks exist, a general kinematic model for parallel robots is still missing. This paper presents the definition of the rotational component of kinematic constraints equations for parallel robots based on two reciprocal sets of Euler angles for the end-effector orientation and the orientation residual. The method allows to completely remove the redundant coordinate in 3T2R tasks and to solve the inverse kinematics for general serial and parallel robots with the gradient-descent algorithm. The functional redundancy of robots with full mobility is exploited using nullspace projection.

With the increasingly stringent airworthiness standards, the noise generated during the rotorcraft flight is gradually attracting people’s attention. It widely operated helicopters at low altitudes because of their maneuverability. The way to reduce the noise caused by the complex airflow of the helicopter rotor system has progressively become a hot topic for researchers. Using a hybrid acoustic analysis method, this paper investigates the improvement of the noise and thrust of the helicopter’s tail rotor through the tail rotor structural parameters. For the basic model, the turbulence simulation is performed using an incompressible detached eddy simulation (DES) method, and the Lighthill acoustic analog equation is calculated using the finite element method (FEM). We verified the accuracy of the method through wind tunnel tests. We chose a series of structural parameters for sound simulation and fluid simulation calculations. The results indicate that the modified tail rotor noise reduced by 16.5 dBA and the total thrust increased by 19.9% from the prototype model. This work can enhance the duct tail rotor design to improve aerodynamic and aeroacoustic performance.

Energy efficiency and leakage magnetic field (LMF) are two important issues in electric vehicle inductive chargers. In this work, the maximum achievable coil efficiency and the corresponding LMF strength are formulated as functions of hardware parameters, and figure of merits (FOM) are proposed for assessing the efficiency and LMF performance of the coil assembly pair. The impacts of the coil assemblies’ geometric parameters on both FOMs are examined with the aid of finite element analysis (FEA), and measures to improve the FOMs are extracted from FEA results. A coil assembly pair is manually optimized within given dimensional limits. Compared with the initial design, the optimized one achieves higher efficiency and lower LMF strength while consuming less copper. The performance improvement is verified by FEA results and experimental data measured on an 85 kHz electric vehicle inductive charger prototype. The key measures for coil assembly optimization are summarized.

This paper describes a new approach that can be used to determine the mechanical properties of unknown materials and complex material systems. The approach uses inverse finite element modelling (FEM) accompanied with a designed algorithm to obtain the modulus of elasticity, yield stress and strain hardening material constants of an isotropic hardening material model, as well as the material constants of the Drucker-Prager material model (modulus of elasticity, cap yield stress and angle of friction). The algorithm automatically feeds the input material properties data to finite element software and automatically runs simulations to establish a convergence between the numerical loading-unloading curve and the target data obtained from continuous indentation tests using common indenter geometries. A further module was developed to optimise convergence using an inverse FEM analysis interfaced with a non-linear MATLAB algorithm. A sensitivity analysis determined that the dual Spherical and Berkovich (S&B) approach delivered better results than other dual indentation methods such as Berkovich and Vickers (B&V) and Vickers and Spherical (V&S). It was found that better convergence values can be achieved despite a large variation in the starting parameter values and / or material constitutive model and such behaviour reflects the uniqueness of the dual S&B indentation in predicting complex material systems. The study has shown that a robust optimization method based on a non-linear least-squares curve fitting function (LSQNONLIN) within MATLAB and ABAQUS can be used to accurately predict a unique set of elastic plastic material properties and Drucker-Prager material properties. This is of benefit to the scientific investigation of properties of new materials or obtaining the material properties at different location of a part which might be not be similar due to manufacturing processes (e.g. different heating and cooling rates at different locations).

Terrestrial LiDAR becomes more and more popular to estimate leaf and plant area density. Voxel-based approaches account for this vegetation heterogeneity and significant work has been done in this recent research field, but no general theoretical analysis is available. Although estimators have been proposed and several causes of biases have been identified, their consistency and efficiency have not been evaluated. Also, confidence intervals are almost never provided. In the present paper, we solve the transmittance equation and use the Maximum Likelihood Estimation (MLE), to derive unbiased estimators and confidence intervals for the attenuation coefficient, which is proportional to leaf area density. The new estimators and confidence intervals are defined at voxel scale, and account for the number of beams crossing the voxel, the inequality of path lengths in voxel, the size of vegetation elements, as well as for the variability of element positions between vegetation samples. They are completed by numerous numerical simulations for the evaluation of estimator consistency and efficiency, as well as the assessment of the coverage probabilities of confidence intervals. • Although commonly used when the beam number is low, the usual estimators are strongly biased and the 95% confidence intervals can be ≈±100% of the estimate. • Our unbiased estimators are consistent in a wider range of validity than the usual ones, especially for the unbiased MLE, which is consistent when the beam number is as low as 5. The unbiased MLE is efficient, meaning it reaches the lowest residual errors that can be expected (for an unbiased estimator). Also the unbiased MLE does not require any bias correction when path lengths are unequal. • When elements are small (or voxel is large), 103 beams entering the voxel leads to some confidence intervals ≈±10%, but when elements are larger (or voxel smaller), it can remain wider than ±50%, even for a large beam number. This is explained by the variability of element positions between vegetation samples. Such a result shows that a significant part of residual error can be explained by random effects. • Confidence intervals are much smaller (±5 to 10%) when LAD estimates are averaged over several small voxels, typically within a horizontal layer or in the crown of individual plants. In this context, our unbiased estimators show a reduction of 50% of the radius of confidence intervals, in comparison to usual estimators. Our study provides some new ready-to-use estimators and confidence intervals for attenuation coefficients, which are consistent and efficient within a fairly large range of parameter values. The consistency is achieved for a low beam number, which is promising for application to airborne LiDAR data. They entail to raise the level of understanding and confidence on LAD estimation. Among other applications, their usage should help determine the most suitable voxel size, for given vegetation types and scanning density, whereas existing guidelines are highly variable among studies, probably because of differences in vegetation, scanning design and estimators.

Cogging torque is a pulsating, parasitic and undesired torque ripple intrinsic of the design of a permanent magnet synchronous generator (PMSG), which should be minimized due to its adverse effects: vibration and noise. In addition, as aerodynamic power is low during start-up at low wind speeds in small wind energy systems, the cogging torque must be as low as possible to achieve a low cut-in speed. A novel mitigation technique using compound pre-slotting, based on a combination of magnetic and non-magnetic materials, is investigated. The finite element technique is used to calculate the cogging torque of a real PMSG design for a small wind turbine, with and without using compound pre-slotting. The results show that cogging torque can be reduced by a factor of 48% with this technique, while avoiding the main drawback of the conventional pre-slotting technique: the reduction of induced voltage due to leakage flux between stator teeth. Furthermore, through a combination of pre-slotting and other cogging torque optimization techniques, 84%, cogging torque can be eliminated for a given design.

Developmental modularity has long been viewed as a hierarchical organization that facilitates evolution over macro-evolutionary time through modification or co-option of preexisting modules. More recently, developmental modularity has been proposed as a micro-evolutionary mechanism capable of driving rapid evolution of novel color pattern phenotypes between closely related taxa. In this scenario, swapping allelic variants of modular cis-regulatory elements (CREs) via recombination generates novel phenotypes by shuffling preexisting color pattern modules into new arrangements. Recent evidence from Drosophila and butterflies, however, provides a series of examples in which pleiotropic CREs function in multiple developmental contexts. The potential prevalence of pleiotropy in CRE function is a major barrier to the proposed evolutionary role of CRE modules and encourages us to reconsider the relative importance of modularity for microevolutionary change. Here we first review the case for the apparent frequent exchange of modular color pattern phenotypes as a mechanism facilitating diversification. We then contrast this with recent evidence of CRE pleiotropy and argue that exchange of CRE modules should not be the default assumption, even when phenotypes look modular. Finally, we review experimental data on Heliconius butterfly wing patterns—which appear modular—and introduce the concept of evolutionary modularity as an alternative to developmental modularity. Evolutionary modularity reconciles the appearance of modularity in comparative genomic studies of Heliconius color patterns with experimental data supporting a non-modular architecture. We propose that evolutionary modularity provides a potentially important pathway for exchange of phenotypic elements between hybridizing taxa independent of the underlying developmental architecture.

Nuclear export of viral mRNAs, is an essential step in the HIV replication cycle. This role is played by a small regulatory protein of HIV-1 called Rev.The N-terminal region of Rev contains an arginine-rich sequence. The arginine-rich motif (ARM) is located between amino acids 38-50 and forms an alpha-helical secondary structure. Expression of the structural proteins of human immunodeficiency virus type 1 requires the direct interaction of multiple copies of the viral Rev protein with its highly structured RNA target sequence, the Rev Response element (RRE). The major viral proteins are not produced if this transport of RNA is stopped. Therefore, knowledge of Rev structure is essential for understanding of its cooperative binding to the RRE, for understanding the mechanism of HIV infection and for the development of antiviral drugs that interfere with Rev’s essential functions and for acknowledgment of good candidate drugs for treatment of AIDS. To understand how REV interact with RRE element of HIV-RNA and its formation of oligomeric complex it is better to characterize the domain wise structure of REV with regard in function of each domain. Due to lack of structural data on Rev no single compound is reported as inhibitor of REV expect antiviral drugs. Identification of a high-affinity RNA-binding site for the human immunodeficiency virus type 1 Rev Protein is much more important. The ARM is a highly specific sequence which allows for the multimerization of Rev and also binding of REV with RNA. Here we are first time exploring the structural characteristics of REV protein both in free form and in complex with RNA at domain function level especially explore the role of ARM motif in REV HIV-1 protein as RNA binding sites by molecular dynamics (MD) simulation and homology modeling studies. Results indicate that the arginine-rich motif (ARM) is crucial in stability of this complex. The residues ARG38, 39, 41, 43, 44, 48, 50, and ASN40 are most interacting with nucleobases of RRE in Crystal structure of Rev and Rev-response-element RNA complex. Our study plays a major role in elaboration of binding of RNA with REV and pave the way for further investigation for therapeutically agent for HIV.

A computational methodology for the hydrodynamic analysis of horizontal axis marine current turbines is presented. The approach is based on a boundary integral equation method for inviscid flows originally developed for marine propellers and adapted here to describe the flow features that characterize hydrokinetic turbines. To this purpose, semi-analytical trailing wake and viscous-flow correction models are introduced. A validation study is performed by comparing hydrodynamic performance predictions with two experimental test cases and with results from other numerical models in the literature. The capability of the proposed methodology to correctly describe turbine thrust and power over a wide range of operating conditions is discussed. Viscosity effects associated to blade flow separation and stall are taken into account and predicted thrust and power are comparable with results of blade element methods that are largely used in the design of marine current turbines. The accuracy of numerical predictions tend to reduce in cases where turbine blades operate in off-design conditions.

The paper aims in assessing risks of mandible fractures consequent to impacts or sport accidents. The role of the structural stiffness of mandible, related to disocclusion state, is evaluated through numerical simulations using the finite element method (FEM). It has been assumed that the quasi-static stress field, due to distributed forces developed during accidents, could explain the common types of mandibular fractures. Geometric model of adolescent mandible was built, upon the basis of medical imaging, in CAD software with distinction between cortical layer and inner spongy bone. The finite element model of disoccluded mandible was next created. Mandibular condyles were supposed jammed in the maxillary fossae. The total force of 700 N, simulating an impact on mandible, has been sequentially applied in three distinct areas: centrally, at canine zone and at the mandibular angle. Clinically most frequent fractures of mandible were recognized through the analysis of maximal principal stress and maximal principal strain fields. Mandibular fracture during accidents can be analyzed at satisfactory level using linear quasi-static FE models for designing protections in sport and transport. The proposed approach can be improved by introducing more realistic interactions between condylar processes and fossae.

The superharmonic imaging of tissue has the potential for high spatial and contrast resolutions, compared to the fundamental and second harmonic imaging. For this technique, the spectral bandwidth of an ultrasound transducer is divided for transmission of ultrasound and reception of its superharmonics (i.e., higher than the second harmonic). Due to the spectral division for the transmission and reception, transmitted ultrasound energy is not sufficient to induce superharmonics in media without using contrast agents, and it is difficult that a transducer has a -6-dB fractional bandwidth of higher than 100%. For the superharmonic imaging of tissue, thus, multi-frequency array transducers are the best choice if available; transmit and receive elements are separate and have different center frequencies. However, the construction of a multi-frequency transducer for intravascular ultrasound (IVUS) imaging is particularly demanding because of its small size of less than 1 mm. Here, we report a recently developed dual-element focused IVUS transducer for the third harmonic imaging of tissue, which consists of a 35-MHz element for ultrasound transmission and a 105-MHz element for third harmonic reception. For high quality third harmonic imaging, both elements were fabricated to have the same focus at 2.5 mm. The results of tissue mimicking phantom tests demonstrated that the third harmonic images produced by the developed transducer had higher spatial resolution and deeper imaging depth than the fundamental images.

Many dioecious plants have sex chromosomes that are cytologically heteromorphic, but about half of species lack cytological differences between males and females and are thus homomorphic. Very little is known about the size and content of the non-recombining sex-determining region (SDR) in these species. Here, we assess the size and content of the SDR of the diploid dioecious herb Mercurialis annua, which has homomorphic sex chromosomes and shows signatures of mild Y-chromosome degeneration. We used RNAseq to identify new Y-linked markers for M. annua. Twelve of 24 transcripts with male-specific and male-biased expression could only be PCR-amplified from males and are thus Y-linked. We found a further six Y-linked sequences that were present in males but not females using genome capture data from multiple populations. We used the Y-linked sequences to identify and sequence 17 sex-linked bacterial artificial chromosomes (BACs), which form 11 groups of non-overlapping sequence, covering a total sequence length of about 1.5 Mb. Content analysis of this region suggests it is enriched for repeats, has a low gene density and contains few candidate sex-determining genes. The BACs map to a subset of the sex-linked region of the genetic map, which is estimated to be at least 14.5 Mb. This is substantially larger than estimates for other dioecious plants with homomorphic sex chromosomes, especially given the small genome size of M. annua. Our data provide a rare, high-resolution view of the homomorphic Y chromosome of a dioecious plant.

Purpose: The aim of the present experimental 3D-finite element study was to evaluate the influence of an augmented sinus lift with an additional inserted bone graft block. The bone graft block stabilizes the implant in addition to conventional augmented bone. We placed the block in three different positions. The implants were loaded with axial force and forces secondary to laterotrusion and protrusion. Material and Methods: A simplified U-shaped 3D finite element model of the upper jaw and a more complex anatomical model of the left maxilla were created. The bone graft block was placed in three positions: in the lower third in contact with the sinus floor, the middle, and the upper third of the implant. Van Mises’ stress distribution was calculated and analyzed for the different models. We also compared the complex anatomical model with the simplified one. Results: The position of the bone graft block significantly influences the magnitude of stress distribution. A bone graft block positioned in the upper third or middle of the implant reduces the quantity of stress compared to the reference model without a bone graft block. The low bone graft block position is clearly associated with lower stress distribution in compact bone. We registered no significant differences in stress in compact bone with regard to laterotrusion or protrusion. Conclusions: Maximum values of von Mises stresses in compact bone can be reduced significantly by using a bone graft block. The reduction of stress is nearly the same for positions in the upper third and the middle of the implant. It is much more pronounced when the bone graft block is in the lower third of the implant near the sinus floor, which appeared to be the best position in the present study.

We have previously reported that 60% sucrose diet-fed ChREBP knockout mice (KO) showed body weight loss resulting in lethality. We aimed to elucidate whether sucrose and fructose metabolism are impaired in KO. Wild type mice (WT) and KO were fed a diet containing 30% sucrose with/without 0.08% miglitol, an α-glucosidase inhibitor, and these effects on phenotypes were tested. Furthermore, we compared metabolic changes of oral and peritoneal fructose injection. Thirty percent sucrose diet feeding did not affect phenotypes in KO. However, miglitol induced lethality in 30% sucrose-fed KO. Thirty percent sucrose plus miglitol diet-fed KO showed increased cecal contents, increased fecal lactate contents, increased growth of lactobacillales and Bifidobacterium and decreased growth of clostridium cluster XIVa. ChREBP gene deletion suppressed the mRNA levels of sucrose and fructose related genes. Next, oral fructose injection did not affect plasma glucose levels and liver fructose contents; however, intestinal sucrose and fructose related mRNA levels were increased only in WT. In contrast, peritoneal fructose injection increased plasma glucose levels in both mice; however, the hepatic fructose content in KO was much higher owing to decreased hepatic Khk mRNA expression. Taken together, KO showed sucrose intolerance and fructose malabsorption owing to decreased gene expression.

Lightning strike can cause a considerable damage in aircraft parts made from semiconducting materials such as Carbon Fiber Reinforced Plastics (CFRPs). Therefore, in recent years, the lightning strike phenomenon has attracted the interest of the academic community and the aircraft industry. Until now, the problem has been addressed mainly experimentally, while the reported numerical works are very limited. In the present work, a coupled electro-thermal FE model has been developed using the ANSYS commercial FE code to simulate the lightning strike damage in unidirectional CFRP laminates due to the Joule heat flux phenomenon. The model is based on the SOLID69 thermoelectric element and applies a non-linear, time-transient analysis. The main input to the model is the thermal-electrical properties of the composite material which vary with temperature. Using the model, a parametric study on the effect of mesh density and peak intensity on the thermal damage has been performed. Three electrical lightning strikes of low (10 kA), medium (30 kA) and high peak intensity (40 kA) have been applied according to the SAE ARP 5412 standard. The electro-thermal model has been validated against a numerical model from the literature. The numerical results reveal that the increase of peak intensity leads to the increase of the area and penetration depth of matrix thermal damage (pyrolysis) as well as to the increase of the area of fiber damage (deterioration and ablation). Through progressive damage modeling, the residual tensile strength of the CFRP plate after being subjected to lightning strike of different peak intensity has been predicted. Lightning strike initial damage has been simulated by translating the thermal field into degradation of elastic properties of the lamina. The results show an increase in the accumulated matrix damage and a decrease of tensile strength due to the initial lightning strike damage. For the maximum peak intensity of 40 kA, a decrease in tensile strength of 4.8% has been predicted

Evidence regarding the effect of the onlay preparation design for different CAD/CAM restorative materials considering the preservation of cusps is lacking. Molars were 3D modeled in four preparation designs for onlay restoration: traditional design with functional cusp coverage (TFC), non-retentive design with functional cusp coverage (NFC), traditional design with non-functional cusp coverage (TNFC), non-retentive design with non-functional cusp coverage (NNFC). Restorations were simulated with two CAD/CAM restorative materials: LD – lithium disilicate (IPS e.max CAD) and RC - resin composite (GrandioBloc). A 100 N axial load was applied to the occlusal surface simulating the centric contact point. Von Mises (VM) and maximum principal (Pmax) stresses were evaluated for restorations, cement layer and dental substrate. The non-retentive preparation design reduced the stress concentration in the tooth structure in comparison to the conventional retentive design. For LD onlays, the stress distribution on the restoration intaglio surface showed that the preparation design as well as the prepared cusp, influenced the stress magnitude. The non-retentive preparation design provided better load distribution in both restorative materials and more advantageous for tooth structure. The resin composite restoration on non-functional cusp is recommended when functional cusp is preserved, in order to associate conservative dentistry and low stress magnitude.

The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. This paper describes the design and analysis of the strain gauge load cell, from the conceptional design stage to shape optimization (based on the finite element method (FEM) technique) and calibration, providing ample load capacity with low-cost material (aluminum 6061) and highly accurate force measurement. The amplifier circuit of the half Wheatstone bridge configuration with two strain gauges has been implemented experimentally with an actual load cell prototype. The calibration test was conducted to evaluate the load cell characteristics and derive the governing equation for sensing the unknown load depending on the measured output voltage. The measured sensitivity of the load cell is approximately 15 mV/N and 446.8 µV/V at a maximum applied load of 30 kg. The findings are supported by FEM results and experiments with an acceptable percentage of errors, which revealed an overall error of 6% in the worst situation. Therefore, the proposed load cell meets the design considerations for axial force measurement for the laboratory test bench, which has a light weight of 20 g and a maximum axial force capacity of 300 N with good sensor characteristics.

The Inverted F Antenna (IFA) with the parasitic element on a finite conducting plane is proposed in the range frequency of 0.1 to 5.5 GHz and its characteristics are analyzed numerically. In this research, the parasitic element and the main IFA are investigated to obtain the resonance frequency for multiband operation purposes. The parasitic element is placed beneath adjusted to the main IFA to derive more frequency bands. The distance between the parasitic element and main horizontal element extremely affects the performance of the IFA. It is found that when the parasitic element is located closer to the conducting plane, this element is coupled by the current on the conducting plane. Consequently, the return loss bandwidth becomes narrower. Therefore, the gain of the proposed IFA becomes a bit higher. The antenna gain is about 8.21 dB at band #3 (λ_1.747), 7.43 dB at band #5 (λ_2.967) and 8.82 dB at band #6 (λ_4.023). This occurs when the calculation condition is antenna height h1 = 23 mm, h2 = 21 mm, horizontal antenna elements L = 173.2 mm, L1 = 140.9 mm and Lp = 152 mm, shorted element Ls = 30.7 mm, the distance between parasitic element and shorted element pyl = 5 mm. While the size of conducting plane is considered pxp+pxm by pyp+pym as 57.5+57.5 mm by 200+50 mm. In the numerical analysis, the electromagnetic simulator WIPL-D based on Method of Moment is used. The results show that the proposed IFA has UHF and SHF channel receiver which are suitable for advanced wireless service (band #3), mobile phones, Bluetooth, maritime service, radiolocation service (band #5) and radars, mobile phones, commercial wireless LAN (band #6).

Aerated concrete, which is manufactured from binding material, sand, foaming agent and water, is currently being utilized in the construction industry because of its lightweight and durability. The binding material, cement, along with other materials used in the concrete produces huge carbon footprints during its fabrication. The utilization of natural aggregates name as coarse aggregates depletes the natural resources of the country. Therefore, huge amounts of agricultural wastes have led scholars to investigate the effectiveness of replacing conventional materials used in concrete with agricultural wastes. In the current study, rice husk ash (RHA) was used as supplementary cementing material, thereby reducing the amount of cement used in aerated concrete (AC) mixture will reduce carbon footprints. The experimental and numerical analysis were conducted to investigate structural behavior of reinforced RAC- B beams subjected to flexural load. Parametric study on structural performance of RAC- B beam under flexure were conducted using finite element analysis (FEA). From the experiment and FEA. Results from the parametric study showed that RAC-10%RHA-B with higher depth structurally performed better compared to RAC-B under flexure with greater load carrying capacity, lesser maximum deflection, and less cracks developing in the tension area.

Since large power transformers are custom-made, and their design process is a labor-intensive task, their design process is split into different parts. In tendering, the price calculation is based on the preliminary design of the transformer. Due to the complexity of this task, it belongs to the most general branch of discrete, non-linear mathematical optimization problems. Most of the published algorithms are using a copper filling factor based winding model to calculate the main dimensions of the transformer during this first, preliminary design step. Therefore, these cost optimization methods are not considering the detailed winding layout and the conductor dimensions. However, the knowledge of the exact conductor dimensions is essential to calculate the thermal behaviour of the windings and make a more accurate stray loss calculation. The paper presents a novel, evolutionary algorithm-based transformer optimization method which can determine the optimal conductor shape for the windings during this examined preliminary design stage. The accuracy of the presented FEM method was tested on an existing transformer design. Then the results of the proposed optimization method have been compared with a validated transformer design optimization algorithm.

Interface between matrix/coating or coating/coating in fact represents a very complicate thin interfacial layer. So interface model is necessary to avoid the difficulty on considering such a complicate thin layer in analysis. Classic interface model and cohesive model have been widely used in stress analysis of coating materials, though they cannot represent the effect of very thin interfacial layer accurately. A complete interface model has been deduced from the equivalent constitutive of interfacial layer in this paper. It is found that both classic interface model and cohesive model sometimes cannot give correct analysis results, while the complete interface model can always give a correct result. Moreover, the stress parallel to interface within the interfacial layer can also be analyzed by the new model. Besides, this model can also be used to describe the equivalent properties of interfacial layer, thereby, can provide a quantitative characterizing method for interfacial layer itself.

SARS-CoV-2 infections underlie the current Coronavirus disease (COVID-19) pandemic and are causative for a high death toll particularly among elderly subjects and those with comorbidities. Selenium (Se) is an essential trace element of high importance for human health and particularly for a well-balanced immune response. Mortality risk from severe disease like sepsis or polytrauma is inversely related to Se status. We hypothesized that this relation also applies to COVID-19. Serum samples (n=166) from COVID-19 patients (n=33) were collected consecutively and analysed for total Se by X-ray fluorescence and selenoprotein P (SELENOP) by a validated ELISA. Both biomarkers showed the expected strong correlation (r=0.7758, p<0.001), pointing to an insufficient Se status for optimal selenoprotein expression. In comparison to reference data from a European cross sectional analysis (EPIC, n=1915), the patients showed a pronounced deficit in total serum Se (mean±SD, 50.8±15.7 vs. 84.4±23.4 µg/L) and SELENOP (3.0±1.4 vs. 4.3±1.0 mg/L). A Se status below the 2.5th percentile of the reference population, i.e., [Se] < 45.7 µg/L and [SELENOP] < 2.56 mg/L was present in 43.4% and 39.2% of COVID samples, respectively. The Se status was significantly higher in samples from surviving COVID patients as compared to non-survivors (Se; 53.3±16.2 vs. 40.8±8.1 µg/L, SELENOP; 3.3±1.3 vs. 2.1±0.9 mg/L). We conclude that Se status analysis in COVID patients provides diagnostic information. However, causality remains unknown due to the observational nature of this study. Nevertheless, the findings strengthen the notion on a relevant role of Se for COVID convalescence, and support the discussion on adjuvant Se supplementation in severely diseased and Se-deficient patients.

The fatigue life of welded joints under cyclic loading is a complex process that can be roughly divided into fatigue crack initiation, crack propagation and final fracture. Usually, these phases are evaluated separately. Several methods are available to estimate the extent of the different phases in welded components, such as stress-based fatigue concepts for crack initiation or linear elastic fracture mechanics for crack propagation; however, distinguishing these phases in welded components is a complex procedure and often relies on assumptions such as transition crack sizes. The objective of this study is to investigate the relationship between fatigue crack initiation and propagation in welded joints using artificially notched specimens with welded joints characteristics of different notch acuity (different radii and opening angle). The experiments show that the investigated relationship basically depends on the notch acuity, the load level and the stress ratio.

Mobile elevating work platforms (MEWPs) consist of a work platform, extending structure, and chassis, and are used to move persons to working positions. MEWPs are useful but are composed of pieces of equipment, and accidents do occur owing to equipment defects. Among these defects, accidents caused by the fracture of bolts fixed to the extension structure and swing system are increasing. This paper presents a failure analysis of the fixing bolts of MEWP. Standard procedure for failure analysis was employed in this investigation. Visual inspection, chemical analysis, tensile strength measurement, and finite element analysis (FEA) were used to analyze the failure of the fixing bolts. Using this failure analysis approach, we found the root cause of failure and proposed a means for solving this type of failure in the future. First, the chemical composition of the fixing bolt is obtained by a spectroscopy chemical analysis method, which determined that the chemical composition matched the required standard. The tensile test showed that the tensile and yield strengths were within the required capacity. The stress analysis was carried out at five different boom angles, and it was determined that the fixing bolt of MEWP can withstand the loads at all the boom angles. The outcomes of the fatigue analysis revealed that the fixing bolt fails before reaching the design requirements. The results of the fatigue analysis showed primarily that the failure of the fixing bolt was due to fatigue. A visual inspection of the fractured section of the fixing bolt also confirmed the fatigue failure. We propose a method to prevent failure of the fixing bolt of the MEWP from four different standpoints: the manufacturer, safety certification authority, safety inspection agency, and owner.

The regulation of hepatic very-low-density lipoprotein (VLDL) secretion plays an important role in the pathogenesis of dyslipidemia and fatty liver diseases. VLDL is controlled by hepatic microsomal triglyceride transfer protein (MTTP). Mttp is regulated by carbohydrate response element binding protein (ChREBP) and small heterodimer partner (SHP). However, it is unclear whether both coordinately regulate Mttp expression and VLDL secretion. Here, adenoviral overexpression of ChREBP and SHP in rat primary hepatocytes induced and suppressed Mttp mRNA, respectively. However, Mttp induction by ChREBP was much more potent than suppression by SHP. Promoter assays of Mttp and the liver type pyruvate kinase gene revealed that SHP and ChREBP did not affect the transactivity of each other. Mttp mRNA and protein levels of Shp^/– mice were similar to those of wild-type; however, those of Chrebp^–/–Shp^–/– and Chrebp^–/– mice were much lower. Consistent with this, the VLDL particle number and VLDL secretion rates in Shp^–/–- mice were similar to wild-type, but were much lower in Chrebp^–/– and Chrebp^–/–Shp^–/–- mice. These findings suggested that ChREBP rather than SHP regulates VLDL secretion and that ChREBP and SHP do not affect the transactivities of each other.

In recent years, numerous topologies of single phase and three phase Field Excited Flux-Switching Machine (FEFSM) have been developed for several applications. Comparative study of three types of single-phase low-priced Field Excited Flux-Switching Machine (FEFSM) is presented in this paper. Both the conventional 8S/4P sub-part rotor design and 6S/3P salient rotor design have an overlapped winding arrangements between armature coil and field excitation coil that depicts high copper losses as well as results in increased size of motor. Additionally, FEFSM with salient structure of the rotor have high flux strength in the stator-core that has much impact on high iron losses. Copper consumption and iron loss being a crucial proportion in total machine losses. Therefore a novel topology of single phase modular rotor field excited FSM with 8S/6P configuration is proposed, which enable non-overlap arrangement between armature coil and FEC winding that facilitates devaluation in the copper losses. The proposed modular rotor design acquires reduced iron losses as well as reduced active rotor mass comparatively to conventional rotor design. It is very persuasive to analyze the best range of speed for these rotors to avoid cracks and deformation, the maximum tensile strength (can be measured with principal stress in research) of the rotor analysis is conducted using JMAG. A deterministic optimization technique is used to enhance the performance of 8S/6P modular rotor design. The electromagnetic performance of conventional sub-part rotor design, F1-A3-3P design and proposed novel-modular rotor design are analyzed by 3D-Finite Element Analysis (3D-FEA), includes flux linkage, flux distribution, flux strength, back-EMF, cogging torque, torque characteristics, iron losses and efficiency.

The present work deals with the development of finite element methodology for obtaining the stress distributions in thick cylindrical HK40 stainless steel pipe that carry high temperature fluids. The material properties and loading are assumed to be random variables. Thermal stresses that are generated along radial, axial and tangential directions are computed generally using analytical expressions which are very complex. To circumvent such an issue, the probability theory and mathematical statistics have been applied to many engineering problems which allows to determine the safety both quantitatively and objectively based on the concepts of reliability. Monte Carlo simulation methodology is used to study the probabilistic characteristics of thermal stresses which is used for estimating the probabilistic distributions of stresses against the variations arising due to material properties and load. A 2-D Probabilistic finite element code is developed in MATLAB and the deterministic solution is compared with ABAQUS solutions. The values of stresses that are obtained from the variation of elastic modulus are found to be low as compared to the case where the load alone is varying. The probability of failure of the pipe structure is predicted against the variations in internal pressure and thermal gradient. These finite element framework developments are useful for the life estimation of piping structures in high temperature applications and subsequently quantifying the uncertainties in loading and material properties.

Globally 30% of landslides occur in the northeastern part of India [1]. One of the major earthquake events in Sikkim, India occurred on 18th September 2011 (Mw 6.9) led to over 300 landslides and 122 human deaths [2]. These landslides not only controlled by natural disasters but initiated due to human activities. The present study considered Lungchok landslide occurred in south district of Sikkim due to 2011 seismic event. The study focused on the failure mechanism of the landslide based on finite element analysis by adopting eight different cases. The deformation characteristic was investigated for dry and saturated slope conditions under static and dynamic behavior considering vehicle loads using GeoStudio software. The FEM analysis has been carried out using load deformation and linear elastic. The analysis shows that the failure of the slope was not sudden due to the 2011 earthquake event, but progressive failure was observed with time and construction activity. The paper demonstrates that, an increase in infrastructure development including construction by hill cutting increased the initiation of landslide with soil erosion. The cracks developed after 2011 earthquake event led to further deformations during future disasters required effective stabilization measures.

Modeling fluid flow in three-dimensional (3D) Discrete Fracture Networks (DFNs) is of relevance in many engineering applications, such as hydraulic fracturing, oil/gas production, geothermal energy extraction, nuclear waste disposal and CO₂ sequestration. A new Boundary Element Method (BEM) technique with discontinuous quadratic elements and a parallel Domain Decomposition Method (DDM) is presented herein for the simulation of the steady-state fluid flow in 3D DFN systems with wellbores, consisting of planar fractures having arbitrary properties and wellbore trajectories. Numerical examples characterized by DFNs of increasing complexity are investigated to evaluate the accuracy and efficiency of the presented technique. The results show that accurate solutions can be obtained with less nodes than with mesh-based methods (e.g. Finite Element Method). In addition, the DDM algorithm used provides a quite fast convergence. The simulation results of the fluid flow around intersections among traces (linear intersections between fractures), intersections between traces and a fracture boundaries, and wellbore intersections is accurate. Source code is available at : https://github.com/BinWang0213/PyDFN3D.

B chromosomes are supernumerary chromosomes which are found in addition to the normal standard chromosomes (A chromosomes). B chromosomes are well known to accumulate several types of repeats. Although the evolution of B chromosomes has been subject of numerous studies, the mechanisms of accumulation and evolution of repetitive sequences is not fully understood. Recently, new genomic approaches have shed light on the origin and accumulation of different classes of repetitive sequences in the process of B chromosome formation and evolution. Here we discuss the impact of repetitive sequences accumulation on the evolution of plant B chromosomes.

The burnout syndrome, which affects so many healthcare workers, has recently awakened wide interest due to the severe repercussions related to its appearance. Even though job factors are determinant to its development, not all individuals exposed to the same work conditions show burnout, which demonstrates the importance of individual variables such as personality. The purpose of this study was to determine personality characteristics of a sample of nursing professionals based on the Big Five model, and then, having determined the personality profiles, analyze the differences in burnout and engagement based on those profiles. The sample was made up of 1236 nurses. An ad hoc questionnaire was prepared to collect the sociodemographic data, and the Brief Burnout Questionnaire, the Utrecht Work Engagement Scale and the Big Five Inventory-10 were used. The results showed that the existence of burnout in this group of workers, is associated negatively with extraversion, agreeableness, conscientiousness and openness to experience, and positively with the neuroticism personality trait. These personality factors showed the opposite pattern with regard to engagement. Three different personality profiles were also found in nursing personnel, in which professionals who had a profile marked by strong neuroticism and low scores on the rest of the personality traits where those who were most affected by burnout.

Prefabricated forms of construction have led to the rapid onsite assembly of buildings however there are still on-site tasks and processes which can be reevaluated and redone specifically in keeping with the principles of prefabrication instead being adapted to fit its purpose. One such process is that of waterproofing between prefabricated panels and modules which come from the factory fully complete façade and all. Conventional means of waterproofing can be used however it results in more work done on site, potential delays and generally requires access from the external face of the building. This paper presents the Modelling, Implementation and Evaluation of purpose developed weatherproof seals specific for Prefabricated Construction. An overview is provided of the entire development process and specific focus is given to the modeling using FEA computer simulations, manufacturing and testing which then resulted in the implementation in a prefabricated panelised building which is used as a case study and the means of further evaluation. These strategies have enabled an efficient and robust prefabricated waterproofing solution specific for this form of construction to be understood and implemented. The resulting case study has successfully verified the time and cost savings when compared to conventional techniques whilst still providing a durable and effective weatherproof seal for prefabricated panelised and modular systems.

A progressive FEA fatigue degradation model for composites was developed and implemented using a UMAT user material subroutine in Abaqus. Numerical results were compared to experimental strain field data from high frequency Digital Image Correlation (DIC) of split disk fatigue testing of pressure vessel cut outs with holes. The model correctly predicted the onset and evolution of damage in the matrix as well as the onset of fiber failure. The model use progressive failure analysis based on the maximum strain failure criterion, the cycle jump method and Miner sum damage accumulation rule. A parameter study on matrix properties was needed to capture the scatter in strain fields observed experimentally by DIC. S-N curve for the matrix material had to be lowered by 0% to 60% to capture the experimental scatter. The onset of local fiber failure had to be described by local S-N curves measured by DIC having 2.5 times greater strain than that of S-N curves found from standard coupon testing.

This study aimed to assess knowledge and practice of caregivers and its relationship to the disease and nutritional status of children under five years of age in rural areas of Sylhet, Bangladesh. A total of 110 households having 6 to 59 months aged children was selected by simple random method from ten rural communities of three Upazila of Sylhet during September 2019 to February 2020. Descriptive statistics were used to assess the WASH knowledge & practice and multivariate chi-square analyses were performed to assess associations among diseases & nutritional status with WASH following a structured questionnaire. The study found a significant association of WASH with childhood disease and nutritional status, and 65% of children were found to be in a diseased state and 35% of children were found to be in a disease-free state within the last six months. The findings sketched that mother with poor wash knowledge and practice was at greater risk for disease outbreaks, disease frequency and duration. The highest incidence of diarrhea was 17% in children aged 12 to 23 months. Significant effect of WASH was also found in children nutrition status, that was reflected in the ratio of stunted, underweight and wasted children. Integrated convergent work focusing on the provision of clean water within the household, stop open defecation, promotion of hand washing, behavior change and poverty alleviation is needed to improve the situation. Health, nutrition and livelihood programs should be uninterrupted, and mothers or caregivers should be encouraged to participate in these programs.

A micromechanical model is implemented to indicate the progressive fatigue problem of a laminated composite with a central circular hole under fatigue loading based on a finite element model. The mechanical properties of the composite lamina are represented based on the characteristics of the fiber and the matrix through a micromechanics model. An appropriate algorithm is then adopted to simulate fatigue damage development in the composite lamina. According to this algorithm, the stress field of the composite subjected to fatigue load is initially obtained using the finite element method. Finally, the predicted results of the stresses in the constituents i.e. fiber and matrix are determined according to the micromechanical bridging model. Finally applying proper damage driving relations leads to damage degree in each element. The proposed model is proven to be successful in the observation of the fatigue behavior with stiffness degradation in each element of the composite in each cycle. Results are reported and validated using those micromechanical models and experimental data available in the literature.

Long-term durability of the vacuum edge-seal plays a significant part in retrofitting triple vacuum glazing (TVG) to existing buildings in achieving towards zero-energy buildings (ZEB) target. Vacuum pressure decrement with respect to time between panes affect the thermal efficiency of TVG. This study reports a 3D finite element model, with validated mathematical methods and comparison, for the assessment of the influence of vacuum pressure diminution on the thermal transmittance (U value) of TVG. The centre-of-pane and total U values of TVG calculated to be 0.28 Wm⁻²K⁻¹ and 0.94 Wm⁻²K⁻¹ at the cavity vacuum pressure of 0.001 Pa. The results suggests that a rise in cavity pressure from 0.001 Pa to 100 kPa increases the centre-of-pane and total U values from 0.28 Wm⁻²K⁻¹ and 0.94 Wm⁻²K⁻¹ to 2.4 Wm⁻²K⁻¹ and 2.58 Wm⁻²K⁻¹, respectively. The temperature descent on the surfaces of TVG between hot and cold sides’ increases by decreasing the cavity vacuum pressure from 50 kPa to 0.001 Pa. To maintain the cavity vacuum pressure of 0.001 Pa for over 20 years of life span in the cavity of 10 mm wide edge sealed triple vacuum glazing, non-evaporable getters will maintain the cavity vacuum pressure that will enable the long-term durability to TVG.

Introduction: Over decades, much have been said and done regarding under-five mortality in Ethiopia. The country has been following the lead of sustainable development goals and UNICEF with its transformation plan targets. However, unless the efforts supported by status assessing studies, it might be difficult for the country to progress. Thus, the current study was directed to identify the prevalence and associated factors of under-five mortality in 2019. Methods: According to the study criteria, we extract and cleaned data in STATA v. 15.0. The data then weighted as per the sampling weight, primary sampling unit, and strata before analyzing in STATA 15.0. Data management consisted of descriptive (mean, standard deviation, and proportion or percent) and association statistics. We deliberated binary logistic regression for this analysis and we checked each variable at 0.25 p-values to include in the model. The final p-value to declare association was p <0.05 and AOR with 95% CI was also applied to describe the results. The data source was the Ethiopian Mini Demographic Health Survey (EMDHS) 2019. EMDHS collected the data from 8,885 in a face-to-face manner with a 99% response rate. Results: From 5,527 numbers of weighted women with under-five analysed in this study, the proportion of under-five mortality was 277.23(5.02%). Factors like 2nd birth order 0.52(0.35, 0.79), 3rd-4th 0.49(0.28, 0.84), 1-2 ANC visits 0.24(0.12, 0.49, ANC visit three’ 0.14(0.07, 0.28), ANC visit four and above 0.22(0.14, 0.36), in marriage mother 0.43(0.19, 0.96), ‘1-2 under-five children 0.02(0.011, 0.03), and greater than three under-five children 0.007(0.0007, 0.004) were all negatively associated with under-five mortality rate. Conclusion: To obtain the exalted outcome out of this study, the government might need to increase antenatal care, women education, institutional delivery, and the modern contraceptive methods use through enhanced community mobilization, health education using community health workers, increasing access to essential cares of mothers and children, and the policy commitment for the issues related to family size, birth order, and birth interval.

Unsupported sleepers or void zones in ballasted tracks are one of the most recent and frequent track failures. The void failures have the property of intensive development that, without timely maintenance measures, can cause the appearance of cost-expensive local instabilities like subgrade damages. The reason of the intensive void development lies in the mechanics of the sleeper and ballast bed interaction. The particularity of the interaction is a dynamic impact that occur due to void closure. Additionally, void zones cause inhomogeneous ballast pressure distribution between the void zone and fully supported neighbour zones. The present paper is devoted studying the mechanism of the sleeper-ballast dynamic impact in the void zone. The results of experimental in-situ measurements of rail deflections showed the significant impact accelerations in the zone even for light-weight slow vehicles. A simple 3-beam numerical model of track and rolling stock interaction has shown the similar to the experimental measurements dynamic interaction. Moreover, the model shows that the sleeper accelerations are more than 3 times higher than the corresponding wheel accelerations and the impact point appear before the wheel enters the impact point. The analysis of ballast loadings shows the specific impact behaviour in combination with the quasistatic part that is different for void and neighbour zones, which are characterised with high ballast pre-stressed conditions. The analysis of void sizes influence demonstrate that the impact loadings, wheel and sleeper maximal accelerations appear at certain void depth after which the values decrease. The ballast quasistatic loading analysis indicates more than twice increase of the ballast loading in neighbour zones for long voids and almost full quasistatic unloading for short length voids. However, the used imitation model cannot explain the nature of the dynamic impact. The mechanism of the void impact is clearly explained by the analytic solution using a simple clamped beam. A simplified analytical expression of the void impact velocity shows that it is linearly related to the wheel speed and loading. The comparison to the numerically simulated impact velocities shows a good agreement and the existence of the void depth with the maximal impact. An estimation of the long-term influences for the cases of normal sleeper loading, high ballast pre-stress and quasistatic loading in the neighbour zones and high impact inside the void are performed.

Detection of early stage corrosion on slender steel members is crucial for preventing buckling failures of steel structures. An active photoacoustic fiber optic sensors (FOS) system has been reported for early stage steel corrosion detection of steel plates and rebars using surface ultrasonic waves. The objective of this paper is to investigate the surface corrosion/rust detection problem on steel rods using numerically simulated surface ultrasonic waves. The finite element method (FEM) is applied in simulating the propagation of ultrasonic waves on steel rod models. Transmission mode of damage detection is adopted, in which one source (transmitter) and one sensor (receiver) are considered. In this research, radial displacements at the receiver were simulated and analyzed by short-time Fourier transform (STFT) for detecting, locating, and quantifying a surface rust located between the transmitter and the receiver. From our time domain and frequency domain analyses, it is found that the presence, location, and dimensions (length, width, and depth) of surface rust can be estimated by ultrasonic waves propagating through the surface rust.

Rubble stone masonry walls are widely diffused in most of the cultural and architectural heritage of historical cities. The mechanical response of such material is rather complicated to predict due to their composite nature. Vertical compression tests, diagonal compression tests, and shear-compression tests are usually adopted to experimentally investigate the mechanical properties of stone masonries. However, further tests are needed for the safety assessment of these ancient structures. Since the relation between normal and shear stresses plays a major role in the shear behavior of masonry joints, governing the failure mode, triplet test configuration was here investigated. First, the experimental tests carried out at the laboratory (LPMS) of the University of L'Aquila on stone masonry specimens were presented. Then, the triplet test was simulated by using the Total Strain Crack Model, which reflects all the ultimate states of quasi-brittle material such as cracking, crushing and shear failure. The goal of the numerical investigation was to evaluate the shear mechanical parameters of the masonry sample, including strength, dilatancy, normal and shear deformations. Furthermore, the effect of (i) confinement pressure and (ii) bond behavior at the sample-plates interfaces were investigated, showing that they can strongly influence the mechanical response of the walls.

In this paper, we investigated transducer placement strategies for detecting crack in primary aircraft structures using ultrasonic Structural Health Monitoring (SHM). The approach developed is for an expected damage location based on fracture mechanics, for example fatigue crack growth in a high stress location. To assess the performance of the developed approach, finite-element (FE) modelling of a damage tolerant aluminum fuselage has been performed by introducing an artificial crack at a rivet hole into the structural FE model and assessing its influence on the Lamb wave propagation, compared to a baseline measurement simulation. The efficient practical sensor position was determined from the largest change in area that is covered by reflected and missing wave scatter using an additive color model. Blob detection algorithms were employed in order to determine the boundaries of this area and to calculate the blob centroid. To demonstrate that the technique can be generalized, the results from different crack lengths and from tilted crack are also presented.

As the first time, 0D-1D-3D and fully 3D steady-state aero-thermo-fluid simulations of a structural oil-to-air Fan Outlet Guide Vane Cooler (FOGVC) in a jet engine are presented. Using the commercial softwares Ansys Fluent, the thermo-mechanical module of Ansys and the 1D fluid solver Flownex, 5 simulation types (3D fully conjugate heat transfer with and without a thin wall model, 3D with a thin wall model, 1D-3D coupled, 1D and 0D) corresponding to 4 levels of simplification in 3 possible domains (oil, oil-metal and oil-metal-air) have been compared to provide selection criteria when a determined level of accuracy in the simulations without prohibited computational times is desired. The methodologies are applied to two different oil internal cavities: an inverted U with rectangular cross section and a coil internal cavity with a circular cross section. The obtained results show that depending on the scope of the research (outlet oil temperature, dissipated heat rate or oil pressure drop) and the accuracy of the results, one method or the other may be used. Experimental data would be needed to validate the numerical results by all employed methodologies and geometries.

The formability and failure behavior of TRIP steel blanks were investigated through various stress states. The forming limit diagram (FLD) at fracture is constructed both experimentally and numerically. Numerical studies are performed to evaluate the applicability of different damage criteria in predicting the FLD as well as complex cross-die deep drawing process. The fracture surface and numerical results revealed that the material failed in a different mode for different strain path. Therefore, Tresca model which is based on shear stress accurately predicted the conditions where shear had the profound effect on the damage initiation, whereas Situ localized necking criterion was able to calculate the conditions which localization was dominant.

Linear elastic fracture modeling coupled with empirical material tension data result in good quantitative agreement with experimental measurements of fracture failure for both brittle and tough epoxy nanocomposites. The nanocomposites comprise diglycidyl ethers of bisphenol A cured with O,O’ bis (2-aminopropylpropylene glycol) (Jeffamine D230) and doped with rubber nanoparticles of varying concentrations. Toughness, critical load, and critical displacement in quasi-static single edge-notched three-point bending are predicted accurately using both surface-based cohesive zone (CZS) and extended finite element (XFEM) methods implemented in Abaqus software. Fracture initiation within a crack is taken at the yield stress from uniaxial tension data. Prediction of fracture processes using a generalized truncated linear traction-separation law was significantly improved by considering the case of a linear softening function. There are no adjustable parameters in the XFEM model. The CZS model requires only optimization of the element displacement at fracture parameter. Thus, these continuum methods describe these materials in mode I fracture with a minimum number of independent parameters.

As long as the non-contact digital printing is not a common standard in the corrugated packaging industry, corrugated board crushing is a real issue that affects the load capacity of the boxes. Crushing mainly occurs during the converting of corrugated board (e.g. analog flexographic printing or laminating) and is a process that cannot be avoided. However, as show in this study, it can be controlled. In this work, extended laboratory tests were carried out on the crushing of double-walled corrugated board. The influence of fully controlled crushing (with a precision: ±10 μm) in the range from 10 to 70 % on different laboratory measurements was checked. Most of the typical mechanical tests were performed e.g. edge crush test, four-point bending test, shear stiffness test, torsional stiffness test, etc. on reference and crushed specimens. The residual thickness reduction of the crushed samples was also controlled. All empirical observations and performed measurements were the basis for building an analytical model of crushed corrugated board. The proven and verified model was then used to study the crushing effect of the selected corrugated board on the efficiency of simple packages with various dimensions.

Zoos are increasingly putting in place formalized animal welfare assessment programs to allow monitoring of welfare over time, as well as to aid in resource prioritization. These programs tend to rely on assessment tools that incorporate resource-based and observational animal- focused measures since it is rarely feasible to obtain measures of physiology in zoo-housed animals. A range of assessment tools are available which commonly have a basis in the Five Domains framework. A comprehensive review of the literature was conducted to bring together recent studies examining welfare assessment methods in zoo animals. A summary of these methods is provided with advantages and limitations of the approach es presented. We then highlight practical considerations with respect to implementation of these tools into practice, for example scoring schemes, weighting of criteria, and innate animal factors for consideration. It is concluded that would be value in standardizing guidelines for development of welfare assessment tools since zoo accreditation bodies rarely prescribe these. There is also a need to develop taxon or species- specific assessment tools to inform welfare management.

In this paper, we present a comprehensive 4D study of the early stage of plastic deformation in a polycrystalline binary AlLi alloy. The entire microstructure is mapped with X-ray diffraction contrast tomography and a set of bulk grains is further studied via X-ray topotomography during mechanical loading. The observed contrast is analyzed with respect to the slip system activation and the evolution of the orientation spread is measured as a function of applied strain. The experimental observations are augmented by the mechanical response predicted by crystal plasticity finite element simulations to analyze the onset of plasticity in details. Simulation results show a general agreement of the individual slip system activation during loading and that comparison with experiments at the length scale of the grains may be used to fine tune the constitutive model parameters.

Variations in the implant thread shape and occlusal load behavior may result in significant changes in the biological and mechanical properties of dental implants and surrounding bone tissue. Most previous studies consider a single implant thread design, an isotropic bone structure, and a static occlusal load. However, the effects of different thread designs, bone material properties, and loading conditions are important concerns in clinical practice. Accordingly, the present study performs Finite Element Analysis (FEA) simulations to investigate the static, quasi-static and dynamic response of the implant and implanted bone material under various thread designs and occlusal loading directions (buccal-lingual, mesiodistal and apical). The simulations focus specifically on the von Mises stress, displacement, shear stress, compressive stress and tensile stress within the implant and the surrounding bone. The results show that the thread design and occlusal loading rate have a significant effect on the stress distribution and deformation of the implant and bone structure during clinical applications. Overall, the results provide a useful insight into the design of enhanced dental implants for an improved load transfer efficiency and success rate.

This paper presents a steady-state and transient heat conduction analysis framework using the polygonal scaled boundary finite element method (PSBFEM) with polygon/quadtree meshes. The PSBFEM is implemented with commercial finite element code Abaqus by the User Element Subroutine (UEL) feature. The detailed implementation of the framework, defining the UEL element, and solving the stiffness/mass matrix by the eigenvalue decomposition are presented. Several benchmark problems from heat conduction are solved to validate the proposed implementation. Results show that the PSBFEM is reliable and accurate for solving heat conduction problems. Not only can the proposed implementation help engineering practitioners analyze the heat conduction problem using polygonal mesh in Abaqus, but it also provides a reference for developing the UEL to solve other problems using the scaled boundary finite element method.

Façade elements are a building component that satisfies multiple performance parameters. Among other things, “advanced façades” take advantage of hybrid solutions, such as assembling laminated materials. In addition to the enhanced mechanical properties that are typical of optimally composed hybrid structural components, these systems are energy-efficient, durable, and offer lighting comfort and optimal thermal performance, an example of which is the structural solution developed in collaboration with the University of Zagreb and the University of Ljubljana within the Croatian Science Foundation VETROLIGNUM project. The design concept involves the mechanical interaction of timber and glass load-bearing members without sealing or bonding the glass-to-timber surfaces. Following earlier research efforts devoted to the structural analysis and optimization of thus-assembled hybrid Cross-Laminated Timber (CLT)-glass façade elements, in this paper, special focus is given to a thermal and energy performance investigation under ordinary operational conditions. A simplified numerical model representative of a full-size building is first presented by taking advantage of continuous ambient records from a Live-Lab mock-up facility in Zagreb. Afterwards, a more detailed Finite Element (FE) numerical analysis is carried out at the component level to further explore the potential of CLT–glass façade elements. The collected numerical results show that CLT–glass composite panels can offer stable and promising thermal performance for façades similar to national and European standard requirements.

High-entropy alloys (HEAs) are of great interest in the field of materials science and engineering. Unlike conventional alloys, which contain a maximum of two base metals, this new category of materials consists of multi-principle elements and the possible number of alloy compositions, in case of HEAs, is outstandingly higher than that for conventional alloys. Here, a review on the high-entropy alloys, has been provided, on the issue whether the earliest definition of High- Entropy alloys, proposed in 2004^{[2, 4]}, is consistent with one of the four-component equiatomic Compositionally complex alloys exhibiting a “High-entropy” effect.

Background: Low-income families often depend on fuels such as wood, coal, and animal dung for cooking. Such solid fuels are highly polluting and are a primary source of indoor air pollutants (IAP). We examined the association between solid fuel use (SFU) and acute respiratory infection (ARI) among under-five children in Afghanistan and the extent to which this association varies by socioeconomic status (SES) and gender. Materials and Methods: This is a cross-sectional study based on de-identified data from Afghanistan’s first standard Demographic and Health Survey conducted in 2015. The sample consists of ever-married mothers with under-five children in the household (n=27,565). We used mixed-effect Poisson regression models with robust error variance accounting for clustering to examine the associations between SFU and ARI among under-five children after adjusting for potential confounders. We also investigated potential effect modification by SES and sex. Additional analyses were conducted using an augmented measure of the exposure to IAP accounting for both SFU and the location of cooking/kitchen (High Exposure, Moderate, and No Exposure). Results: Around 70% of households reported SFU, whereas the prevalence of ARI was 17.6%. The prevalence of ARI was higher in children living in households with SFU compared to children living in households with no SFU (adjusted prevalence ratio [aPR]= 1.10; 95%CI: 0.98, 1.23). We did not observe any effect modification by SES or child sex. When using the augmented measure of exposure incorporating the kitchen’s location, children highly exposed to IAP had a higher prevalence of ARI compared to unexposed children (aPR 1.17; 95% CI: 1.03, 1.32). SES modified this association with the strongest associations observed among children from the middle wealth quintile. Conclusion: The findings have significant policy implications and suggest that ARI risk in children may be reduced by ensuring clean cookstove as well as clean fuels and acting on the socio-environmental pathways.

In this paper we explore extending the concept of common cross-study Common Data Element concepts beyond simple demographics to cover disease-specific concepts relevant to imaging. We test interactively linking the resulting database to the associated images in a federated manner. We examine the use of existing standards, not only for terminology, but for interchange of serialized data in forms familiar to imaging and clinical trials specialists and their dedicated systems. Our intent is to perform preliminary work to inform both the upcoming Imaging Data Commons specifically, as well as more general integration projects beyond imaging.

This paper presents a demonstration of the feasibility of fabricating micro-cantilever harvesters with extended stress distribution and enhanced bandwidth by exploiting an M-shaped two-degrees-of-freedom design. The measured mechanical response of the fabricated device displays the predicted dual resonance peak behavior with the fundamental peak at the intended frequency. This design has the features of high energy conversion efficiency in a miniaturized environment where the available vibrational energy varies in frequency. It makes such a design suitable for future large volume production of integrated self powered sensors nodes for the Internet-of-Things.

This paper discusses recent developments in creep, over a wide range of temperature, that mqy change our understanding of creep. The five-power law creep exponent (3.5 to 7) has never been explained in fundamental terms. The best the scientific community has done is to develop a natural three power-law creep equation that falls short of rationalizing the higher stress exponents that are typically five. This inability has persisted for many decades. Computational work examining the stress-dependence of the climb rate of edge dislocations we may rationalize the phenomenological creep equations. Harper-Dorn creep, “discovered” over 60 years ago has been immersed in controversy. Some investigators have insisted that a stress exponent of one is reasonable. Others believe that the observation of a stress exponent of one is a consequence of dislocation network frustration. Others believe the stress exponent is artificial due to the inclusion of restoration mechanisms such as dynamic recrystallization or grain growth that is not of any consequence in the five power-law regime. Also, the experiments in the Harper-Dorn regime, which accumulate strain very slowly (sometimes over a year) may not have attained a true steady state. New theories suggest that absence or presence of Harper-Dorn may be a consequence of the initial dislocation density. Novel experimental work suggests that power-law breakdown may be a consequence of a supersaturation of vacancies which increase self-diffusion.

Both drag and lift forces impact an inclined plane when it is dragged through a granular bed. In this paper, the following results have been obtained: the drag and lift forces grow with the velocity of motion; when the immersion depth is constant, the inclination angle has no effect on drag force, however, the lift force increases linearly with this inclination angle; the ratio of drag and lift forces is exactly equal to the tangent value of the inclined angle. In order to describe this physical process macroscopically, a continuum wedge model based on the Coulomb model is established to predict drag and lift forces. Particularly，the dynamic friction angle in the assumed shear band is predicted as a function of both inclined angle and moving velocity.

Zero-rate output (ZRO) drift induces deteriorated micro-electromechanical system (MEMS) gy-roscope performances, severely limiting its practical applications. Hence, it is vital to explore an effective method toward ZRO drift reduction. In this work, we conduct an elaborate investigation on the impacts of the internal and packaging stresses on the ZRO drift at the thermal start-up stage, and propose a temperature-induced stress release method to reduce the duration and magnitude of ZRO drift. Self-developed high-Q dual mass tuning fork gyroscopes (TFGs) are adopted to study the correlations between temperature, frequency and ZRO drift. Furthermore, a rigorous finite element simulation model is built based on the actual device and packaging structure, revealing the temperature and stresses distribution inside TFGs. Meanwhile, the relationship between temperature and stresses are deeply explored. Moreover, we introduce a temperature-induced stress release process to generate thermal stresses and reduce the temperature-related device sensitivity. By this way, the ZRO drift duration is drastically reduced from ~2000 s to ~890 s, and the drift magnitude decreases from ~0.4 °/s to ~0.23 °/s. This stress release method achieves a small bias instability (BI) of 7.903 °/h and a low angle random walk (ARW) of 0.792 °/√h, and the long-term bias performance is significantly improved.

Two opposed p–n diodes are connected with another junction that causes cancellation of the electric field in the depletion layer of each diode by the field of the other diode. This derived quantum diode is called the A system. Another dual diode, constructed by the same process but with the p- and n-types positioned as duality, called the B system. When a bias voltage is applied between the A and B systems, Lorentz conservation imparts a momentum (i.e., a wave number) to the carriers in the absence of any internal voltage. Thus, a superconducting bias current density appears without the need for cooling. The reappearances of electron–hole pairs on the junction surfaces are assumed to be described by entire wavefunctions normalized by the band gap. Based on the bias superconducting current, NOT and NAND gates were constructed from the quantum diode systems. Numerical calculations revealed that the constant phases of the entire wavefunctions of the p-and n-types converged. Accordingly, it was clarified that Bose–Einstein condensation and the Meissner effect (described by the London equation) occurred in the quantum diode systems. Moreover, the systems exhibited rectification characteristics and a switching speed of the order of 10^-14 s. Combining this switching property with the large bias superconducting current (of the order of several V), we developed NOT and NAND gates with direct quantum correlations among many qubits, which are unaffected by random and thermal noises. These gates have memorization and initialization properties and are compatible with existing and accumulating programing algorithms. Moreover, when harvesting a divergent current output from these systems, the bias superconducting current and memorization property preserve the formed quantum correlations.

EIT-MESHER (https://github.com/EIT-team/Mesher) is C++ software, based on the CGAL library, which generates high quality Finite Element Model tetrahedral meshes from binary masks of 3D volume segmentations. Originally developed for biomedical applications in Electrical Impedance Tomography (EIT) to address the need for custom, non-linear refinement in certain areas (e.g. around electrodes), EIT-MESHER can also be used in other fields where custom FEM refinement is required, such as Diffuse Optical Tomography (DOT).