Luminophores featuring thermally activated delayed fluorescence (TADF luminophores) are the workhorse of the third- and fourth-generation OLEDs. While these compounds had usually been used as dopants embedded in the host, non-doped TADF OLEDs have recently shown significant progress as well reaching the performance comparable to the host-dopant ones. For efficient operation of the non-doped OLEDs, charge transport in neat films and single crystals of TADF luminophores is important; however, this issue was nearly unexplored theoretically. In the current study, we calculated charge mobilities in four TADF single crystals, which have different molecular packing motifs. Specifically, in one of them both donor and acceptor moieties form uniform π-stacks, while in the others donors (acceptors) show alternating lateral shifts along the stacks; the difference in molecular packing results in the difference of transfer integral between the molecules. Reorganization energies differ as well up to four times for the studied crystals. As a result, charge mobilities vary from 0.001 to ~0.3 cm2/(V∙s), the largest being predicted for the crystal of the luminophore consisting of rigid donor and acceptor. We anticipate that the results obtained can be useful for the design of TADF luminophores for non-doped OLEDs, OLETs and other organic light-emitting devices.

Small and micro hydropower represents an attractive solution for electricity generation, with low cost and low environmental impact. The pump-as-turbine (PAT) approach has promise in this application owing to its low purchase and maintenance costs. In this paper, a new method to predict the inverse characteristic of industrial centrifugal pumps is presented. This method is based on results of simulations performed with commercial three-dimensional CFD software. Model results have been first validated in pumping mode using data supplied by pump manufacturers. Then, results have been compared to experimental data for a pump running in reverse condition. Experimentation has been performed on a dedicated test bench installed in the Department of Civil Construction and Environmental Engineering of the University of Naples Federico II. Three different pumps, with different specific speeds, have been analyzed. Using the model results, the inverse characteristic and the best efficiency point have been evaluated. Finally, results of this methodology have been compared to prediction methods available in the literature.

The UN Sustainable Development Goal 7 Report 2022 is about ensuring access to clean and affordable energy, which is key to the development of agriculture, business, communications, education, healthcare, and transportation. The lack of access to energy hinders economic and human development. Nevertheless, the current pace of progress is insufficient to achieve Goal 7 by 2030. Huge disparities in access to modern sustainable energy persist. Rising commodity, energy and shipping prices have increased the cost of producing and transporting solar photovoltaics modules, wind turbines and biofuels worldwide, adding uncertainty to a development trajectory that is already far below Goal 7 ambitions. Achieving energy and climate goals will require continued policy support and a massive mobilization of public and private capital for clean and renewable energy such as methane from biomass. An important factor in improving methane yield from biomass waste is pre-treatment of the biomass prior to anaerobic digestion. Size reduction of lignocellulose biomass is important for changing and increasing digestibility thus increasing methane yield. A Hollander beater was used as the mechanical pre-treatment machine throughout this study. Results indicate that methane yield is directly proportional to feedstock/Inoculum (F/I) ratio as higher F/I ratio led to higher methane yield. It was observed at an F/I ratio of 0.5 that 5 minutes pre-treatment time produced highest methane yield, while the lowest methane yield was observed at an F/I ratio of 0.2 with 1 minute of pre-treatment time. Methane yield decreased by 30% from 140 mL gTS-1 at F/I ratio 0.5 with 5 minutes pre-treatment time to 98 mL gTS-1 at F/I 0.2 with 5 minutes pre-treatment time. The optimum methane yield was attained at high F/I ratio allowing sufficient nutrient essential for complete degradation of biomass. Overall, this research shows the Hollander beater is not efficient in optimizing methane yield for cardboard.

Quantum-dot cellular automata (QCA) are a promising nanoscale computing technology that exploits the quantum mechanical tunneling of electrons between quantum dots in a cell and electrostatic interaction between dots, in neighboring cells. QCA can achieve higher speed, lower power, and smaller areas than conventional complementary metal–oxide–semiconductor (CMOS) technology. Developing QCA circuits in a logically and physically reversible manner can provide exceptional reductions in energy dissipation. The main challenge of reversible QCA design is to maintain reversibility down to the physical level. The arithmetic logic unit (ALU) is an essential component of the central processing unit (CPU) of a computer. It performs various arithmetic and logical operations on the data that the CPU processes. Current QCA ALU designs are either irreversible or logically reversible; however, they lack physical reversibility, a crucial requirement to increase energy efficiency. In this paper, we present a novel multilayer design for a logically and physically reversible QCA ALU based on majority gates as the key components, which can perform 16 different operations. We use QCADesigner-E software to simulate and evaluate energy dissipation. The proposed logically and physically reversible QCA ALU offers an improvement of 88.8% in energy efficiency. Compared to the next most efficient 16-operation QCA ALU, this ALU uses 51% fewer QCA cells and 47% less area.

Recently, there has been a growing interest in the production of electricity from renewable energy sources (RES). The RES investment is characterized by uncertainty, which is long-term, costly, depend on feed-in-tariff and support schemes. In this paper, we address the real option valuation (ROV) of a solar power plant investment. The real option framework is investigated. This framework considers the renewable certificate price, furthermore the cost of delay between establishing and operating the solar power plant. The optimal time of launching the project and assess the value of deferred option are discussed. The new three stage numerical methods are constructed, the Lobatto3C-Milstein (L3CM) methods. The numerical methods are integrated with concept of Black-Scholes option pricing theory, and applied in option valuation for solar energy investment with uncertainty. The numerical results of L3CM, finite difference and Monte Carlo methods are compared to show the efficiency of our methods. Our data set refers to the Arab Republic of Egypt.

The article presents a model for optimizing biomass supply chains using the linear programming framework integrated with a Geographic Information System. Based on the distance from a given type of biomass resource, its calorific value, price, and transportation costs, the model identifies the optimal source of biomass, allowing it to cover the demand for the required total energy value with the lowest possible costs. The case study includes the Połaniec power plant in southeastern Poland and potential sources of forest biomass and agricultural straw within 100 km of the plant. Unit costs of biomass varied depending on biomass availability and energy demands. For energy demand on the level of 1 PJ yearly, the lowest unit costs of biomass (4.08 €/MJ) were when all kinds of biomass were available, and the highest (5.47 €/MJ) was when only stacked wood was available. As energy demand increased, unit costs increased, and the ability to meet this demand with just one type of biomass decreased. The energy biomass sector can utilize the model to benefit both biomass producers and their final buyers.

The field dynamics of neutral and charged matter (treated as gauge fields) beyond the event horizon of black holes are investigated. As an extension of the work done in Ganesan (2023) [1], the analysis was done using the combined dynamics of the two-dimensional Yang-Mills and Liouville gravity fields beyond the event horizon. The quantum interactions and symmetry breaking mechanisms of the combined two-dimensional fields are discussed. The second part of this paper explores the quantum dynamics occurring at the event horizon. By considering the structure of the event horizon as a Möbius strip (embedded in three-dimensional space), a formulation for the lower bound of the first energy eigenvalue of a quantum particle (electron) at the event horizon is obtained.

This study considers an application of the first-order Grey Markov Model to foresee the values of Italian power generation in relation to the available energy sources. The model is used to fit data from the Italian energy system from 2000 to 2022. The integration of Markovian error introduces a random element to the model, which is able now to capture inherent uncertainties and misalignments between the Grey model predictions and the real data. This application provides valuable insights for strategic planning in the energy sector and future developments. The results show good accuracy of the predictions, which provides powerful information for the effective implementation of energy policies concerning the evolution of energy demand in the country. Despite advancements, Italy’s 2032 energy mix will still significantly rely on fossil fuels, emphasizing the need for sustained efforts beyond 2032 to enhance sustainability.

Nine variants of regular lattice structures with different relative densities have been designed and successfully manufactured. The produced structures have been subjected to geometrical quality control, and the manufacturability of the implemented selective laser melting SLM technique has been assessed. It was found that the dimensions of the produced lattice struts differ from those of the designed struts. These deviations depend on the direction of geometrical evaluation. Additionally, the microstructures and phase compositions of the obtained structures were characterized and compared with those of conventionally produced 316L stainless steel. The microstructure analysis and X-Ray Diffraction XRD patterns revealed a single austenite phase in the SLM samples. Both a certain broadening and a displacement of the austenite peaks were observed due to residual stresses and a crystallographic texture induced by the SLM process. Furthermore, the mechanical behavior of the lattice structure material has been defined. It was demonstrated that under both quasi-static and dynamic testing, lattice structures with high relative densities are stretch-dominated, whereas those with low relative densities are bending-dominated. Moreover, the linear relationship between the energy absorption and relative density under dynamic loading conditions has been defined

Solar radiation is the main energy source for mankind and an accurate data of solar radiation levels for a particular location is vital for the optimum operation of solar energy transducers such as photovoltaic cells and solar thermal collectors. In this work, we show that there is a linear relationship between recorded monthly average temperatures and solar radiation in Swaziland. The correlation can be utilized to develop two mathematical models for the estimation of solar radiation: one from the measured monthly average temperatures and the other based on the square-root of the difference between measured maximum and minimum monthly average temperatures. Both models fit the data well and can be applied to estimate solar radiation in other parts of the region.

Hydrogen plays an important role in the implementation of Australia’s Net-Zero Strategy. It competes with lithium-ion rechargeable batteries in the electrification of Australian land transportation sector, and can provide an alternative energy storage medium for the greening of the country’s electrical grid system. This paper reviews the role hydrogen plays in the current government’s Net-Zero strategy, and investigates the potential role of other bioenergy sources. It is found that hydrogen and batteries play essentially complementary roles in reducing transport emissions, and that the former energy source is more suited to the operation of long-distance commercial service vehicles than batteries. It is suggested that bioenergy fuels such as biomethane, second generation biofuels and HVO can provide suitable bridging alternatives in the event that Australia’s EV strategy is unable to meet the 2030 target.

The paper discusses the 2022 Nobel Prize in physics for experiments of entanglement “establishing the violation of Bell inequalities and pioneering quantum information science” in a much wider, including philosophical context legitimizing by the authority of the Nobel Prize a new scientific area out of “classical” quantum mechanics relevant to Pauli’s “particle” paradigm of energy conservation and thus to the Standard model obeying it. One justifies the eventual future theory of quantum gravitation as belonging to the newly established quantum information science. Entanglement, involving non-Hermitian operators for its rigorous description, non-unitarity as well as nonlocal and superluminal physical signals “spookily” (by Einstein’s flowery epithet) synchronizing and transferring some nonzero action at a distance, can be considered to be quantum gravity so that its local counterpart to be Einstein’s gravitation according to general relativity therefore pioneering an alternative pathway to quantum gravitation different from the “secondary quantization” of the Standard model. So, the experiments of entanglement once they have been awarded by the Nobel Prize launch particularly the relevant theory of quantum gravitation grounded on “quantum information science” thus granted to be nonclassical quantum mechanics in the shared framework of the generalized quantum mechanics obeying rather quantum-information conservation than only energy conservation. The concept of “dark phase” of the universe naturally linked to the very well confirmed “dark matter” and “dark energy” and opposed to its “light phase” inherent to classical quantum mechanics and the Standard model obeys quantum-information conservation, after which reversible causality or the mutual transformation of energy and information are valid. The mythical Big Bang after which energy conservation holds universally is to be replaced by an omnipresent and omnitemporal medium of decoherence of the dark and nonlocal phase into the light and local phase. The former is only an integral image of the latter and borrowed in fact rather from religion than from science. Physical, methodological and proper philosophical conclusions follow from that paradigm shift heralded by the 2022 Nobel Prize in physics. For example, the scientific theory of thinking should originate from the dark phase of the universe, as well: probably only approximately modeled by neural networks physically belonging to the light phase thoroughly. A few crucial philosophical sequences follow from the break of Pauli’s paradigm: (1) the establishment of the “dark” phase of the universe as opposed to its “light” phase, only to which the Cartesian dichotomy of “body” and “mind” is valid; (2) quantum information conservation as relevant to the dark phase, furthermore generalizing energy conservation as to its light phase, productively allowing for physical entities to appear “ex nihilo”, i.e., from the dark phase, in which energy and time are yet inseparable from each other; (3) reversible causality as inherent to the dark phase; (4) the interpretation of gravitation only mathematically: as an interpretation of the incompleteness of finiteness to infinity, for example, following the Gödel dichotomy (“either contradiction or incompleteness”) about the relation of arithmetic to set theory; (5) the restriction of the concept of hierarchy only to the light phase; (6) the commensurability of both physical extremes of a quantum and the universe as a whole in the dark phase obeying quantum information conservation and akin to Nicholas of Cusa’s philosophical and theological worldview.

Mass hauling operations play central roles in construction projects. They typically use many haulers that consume large amounts of energy and emit significant quantities of CO₂. However, practical methods for estimating the energy consumption and CO₂ emissions of such operations during project planning are lacking. This paper presents a detailed model for estimating the energy consumption and CO₂ emissions of mass haulers that integrates the mass hauling plan with a set of predictive equations. The mass hauling plan is generated using a planning program such as DynaRoad in conjunction with data on the productivity of selected haulers and the amount of material to be hauled during cutting, filling, borrowing, and disposal operations. This plan is then used as input for estimating the energy consumption and CO₂ emissions of the selected hauling fleet. The proposed model will help planners to assess the energy and environmental performance of mass hauling plans, and to select hauler and fleet configurations that will minimize these quantities. The model was applied in a case study, demonstrating that it can reliably predict energy consumption, CO₂ emissions, and hauler productivity as functions of the hauling distance for individual haulers and entire hauling fleets.

Time and space are fundamental concepts for characterizing and understanding our world. Despite of continuous curiosity and extensive studies, the nature of time and space remains elusive, and the underlying quantum structure is unclear. Here we propose a molecular model based on energy space decomposition to incorporate time and space synthetically in a unified framework. In the proposed model, the multipole expansion of action mapped to energy modules in scalar, vector, and matrix forms, results in the generators of time, space, and a material framework, cloud. And the invariance of time, space and cloud transformation corresponds to the conservation of energy, momentum, and mass, respectively. The classification of energy modules reveals a periodicity of energy elements, which constructs a hierarchical world in a molecular framework with dynamics represented by energy transformations. Here the role of time and space could switch from each other, and motion is attributed to the coupling of particle with intermediate bosons, corresponding to energy transformations among different energy modules. The application on Bohr model demonstrates that this picture provides a consistent classical interpretation to the foundation of quantum mechanics, and suggests an atomic model for gravitation.

A topological quantum interplay between the magnetic flux and the mass has been investigated, for the case of an electron, by evaluating a gauge-invariant phase factor (a Wilson loop) linked to the electromagnetic gauge field of the particle. In particular, from this phase factor and the quantization of the magnetic flux variations, a relationship between the mass at rest of the electron and its self-energy , arising from radiative corrections, has been obtained also within a QED approach. Besides, a formulation of an energy scale comparable to the energy at rest of an electron-positron pair is proposed. Remarkably, a reckoning of the Bohr energy of a W⁺ W^- pair is compatible with constants and parameters usually employed within the electroweak theory and comparable to the energy at rest of an electron-positron pair.

The article focuses on mining of non-energy mineral resources with minimum environmental impacts. It issues from research results of a project Competence Centre for Effective and Ecological Mining of Mineral Resources implemented at the Faculty of Mining and Geology at VŠB-Technical University of Ostrava, Czech Geological Survey, a company Watrad ltd., a state enterprise Diamo, a company RPS Ostrava plc and a company Sedlecký kaolin plc. The paper starts with a partial analysis of the existing legal norms related to mining and processing of mineral resources. Next, it analyses mineral resource mining options free of negative environmental impacts. The fundamental tool to assess potential environmental impacts of mining is the implementation of Environmental Impact Assessment (EIA) process for a given mineral resource. In the Czech Republic environmental impact assessment is carried out by course of Act 100/2001 Coll. Its important amendment is Act 39/2015 Coll. claiming, inter alia, that the environmental impact assessment is rigidly connected with other permits and procedures, such as the zoning process and building construction permits. The article describes the environmental impacts of mining of non-energy mineral resources, including the following factors: appropriation of land, impacts on surface water, ground water and soil, noise, influence on the landscape character, and air pollution. The paper also includes a case study summarizing information on the environmental factors that may play a role in potential underground mining of graphite in the deposit Český Krumlov - Městský Vrch and the deposit Lazec - Křenov.

Our goal in this paper is to study the relationship between the linear approximation of Einstein's equations to the Klein-Gordon’s equation. The part one presents what the Klein-Gordon’s equation and the integration of the theory of quantum information in it. The Part two deals with the Stress Energy tensor quantum, wherein the detail I linearized gravity of Einstein equation, and wherein I develop the tensor quantum energy pulse from the equivalence of equation einstein the linearized gravity and the Schrödinger equation relativistic described by Klein-Gordon’s equation.

The analysis of the key factors which prevent or contribute to the promotion and development of the Power Purchase Agreements (PPAs) in order to meet the sustainability goals represents an important issue which worth being investigated, especially in the situation in which entering in bilateral relations inside this contract has a powerful meaning in achieving new climate targets, developing and improving the use of green energy, and promoting a sustainable green economy. The main goal of this research is to identify and analyze the main factors which help or pre-vent the promotion and development of a PPA, in order to meet the sustainability goals by promoting a green economy. For this research survey based on comparative analysis, questionnaires and interviews with energy experts, Spearman’s correlation matrix and IBM SPSS Statistics for Window are also used. The results suggest that although there are positive interest and an open attitude towards the PPA from both sides (sellers and buyers), but there is still place for improvement, the lack of knowledge or the insufficient measures taken so far being two of the reasons way until now in Romania we do not have a developed PPA market and the level of knowledge regarding this type of mechanism is quite low.

In this paper, we investigate the structural, microstructural, dielectric, and energy storage properties of Nd and Mn co-doped Ba0.7Sr0.3TiO3 [(Ba0.7Sr0.3)1-xNdxTi1-yMnyO3 (BSNTM) ceramics (x = 0, 0.005, and y = 0, 0.0025, 0.005, and 0.01)] via a defect dipole engineering method. The complex defect dipoles (MnTi"-VO∙∙)∙ and (MnTi"-VO∙∙) between acceptor ions and oxygen vacancies capture electrons, enhancing the breakdown electric field and energy storage performances. XRD, Raman spectroscopy, and microscopic investigations of BSNTM ceramics revealed the formation of a tetragonal phase, increased oxygen vacancies, and reduced grain size with Mn dopant, respectively. The BSNTM ceramics with x=0.005 and y=0 exhibit a high dielectric constant of 2058 and a dielectric loss of 0.026 at 1 kHz. These values gradually decreased to 1876 and 0.019 for x=0.005 and y=0.01 due to the Mn2+ ions at Ti4+-site, which facilitates the formation of oxygen vacancies, and prevents the decrease of Ti4+. In addition, the defect dipoles act as a driving force for depolarization to tailor the domain formation energy and domain wall energy, which provides a high difference between the maximum polarization of Pmax and remnant polarization of Pr (ΔP=10.39 µC/cm2). Moreover, the complex defect dipoles with optimum oxygen vacancies in BSNTM ceramics can provide not only a high ΔP but also reduce grain size, which together improve the breakdown strength from 60.4 to 110.6 kV/cm, giving rise to a high energy storage density of 0.41 J/cm3 and high efficiency of 84.6% for x=0.005 and y=0.01. These findings demonstrate that defect dipoles engineering is an effective method to enhance the energy storage performance of dielectrics for capacitor applications.

Intraband energy transitions of an electron in GaAs/AlGaAs hexagonal quantum well wires in the presence of external electric and magnetic fields are presented. We consider the effects of the revolve of the quantum well wires via a geometric factor that converts the quantum wires straight and symmetric with respect to the z−axis, into a curved wires that no longer has this symmetry. In addition, the influence of having a shallow donor impurity on (off) is calculated. The shape of this quantum string corresponds to the core/shell structure. The energy levels and wave functions of the electron in the heterostructure with a finite potential between the shells are calculated using the effective mass approximation and the finite element method. The calculations of the optical properties are obtained from the compact density matrix and an iterative method. The direction of the applied external fields is parallel (anti-parallel) to the z−direction. The results reveal a significant dependence of the physical properties calculated with the deformation parameter, the dimensions of the quantum well wires and the presence or not of the impurity. The electronic transitions are in a range between 4.90 meV to 41.50 meV under the effect of the electric field, this corresponds to a range of frequencies of optical responses between 1.20 to 10 THz, that is, the mid-infrared. For the magnetic field the range is between 1.24 meV to 14 meV, that is, in frequencies from 0.36 to 3.38 THz, that is, in the far-infrared.

Nepal, primarily an agricultural country, heavily relies on agricultural residue and fuelwood for daily energy requirements. In 2022, total energy consumption was 640 PJ, with traditional sources accounting for 64.17%, and fuelwood comprising 58.53% of total fuel consumption. The estimated potential supply of agricultural residue is 26 million tonnes, yielding about 442 million GJ of energy in 2021. Biomass trading often emphasizes volume or weight, necessitating a rapid and non-destructive assessment of energy properties for mutual benefit, aiding in the identification, management, and utilization of biomass sources. In this study, 200 biomass samples were collected in two batches (126 and 74 samples) from various locations in Nepal. Using Partial Least Squares Regression (PLSR), a model was developed correlating higher heating value (HHV) from a bomb calorimeter and spectral data from Fourier Transform near-infrared spectroscopy (FT-NIRS) (3595 – 12,489 cm-1) sensor. PLSR models incorporated raw spectra, eight preprocessing techniques, the multi-preprocessing five-range method, and a genetic algorithm. Outliers in the first batch were identified, and the first batch divided into an 80% calibration set and a 20% validation set, while the second batch was designated as an unknown sample set. The optimum PLSR model, utilizing first derivative preprocessing, improved accuracy by 6.77%, with coefficients of determination in the calibration set, validation set, and unknown set as 0.9694, 0.9578, and 0.8089, respectively. Root mean square errors were 132.4790 J/g, 189.4800 J/g, and 360.8845 J/g for the calibration set (RMSEC), validation set (RMSEP), and unknown set (RMSEUN), respectively. The prediction to deviation ratio (RPD) for the validation set and unknown set was 4.9 and 2.4, respectively. The cross validation model of combined sample data of every sets showed the R2CV of 0.95 and RPDCV of 4.6 indicating the model could serve as a reliable and swift non-destructive alternative for evaluating biomass HHV using NIRS and ready for updating for industrial use. However, incorporating a larger number of representative samples is crucial to enhance accuracy and develop a more comprehensive global model for predicting biomass HHV.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

In steel structures, oblique thin steel plates serve as panel zones in structures spanning large spaces (e.g., warehouses and gymnasiums). Considerable research has been conducted on the shear buckling of panels due to seismic loads acting on a structure. Conversely, under snow or wind loads, the panel zone may experience compressive and tensile stresses simultaneously from two directions. Considering the economic preference for thin steel plates, evaluating the elastic critical local buckling stresses in the panel zone under biaxial normal stress may provide essential information to structural engineers. In this study, an elastic buckling analysis based on the energy method is performed to clarify the impact of panel geometry and boundary conditions on the elastic local buckling stresses of oblique panel zones. As confirmed, the buckling stresses derived from the energy method could simulate the local buckling stresses with accuracy comparable to that of finite element analysis, and an engineer-friendly design formula was proposed. Finally, we determined the correlation of the buckling stresses under biaxial stresses and presented a method for evaluating this correlation. Engineers can utilize the provided design equations to more efficiently and accurately calculate buckling loads, facilitating safer and more economical design of structures with oblique plates.

This paper performs a comprehensive analysis of the wind energy potential of onshore regions in Greece with emphasis on quantifying the volume risk and the spatial covariance structure. Optimization techniques are employed to derive efficient wind capacity allocation plans (also known as generation portfolios) incorporating different yield aspirations. The generation profile of minimum variance and other optimal portfolios along the efficient frontier are subject to rigorous evaluation using a fusion of descriptive and statistical methods. In particular, principal component analysis is employed to estimate factor models and investigate the spatiotemporal properties of wind power generation, providing valuable insights into the persistence of volume risk. The overarching goal of the study is to employ a set of statistical and mathematical programming tools guiding investors, aggregators and policy makers in their selection of wind energy generating assets. The findings of this research challenge the effectiveness of current policies and industry practices, offering a new perspective on wind energy harvesting with a focus on the management of volume risk.

Cantilever beams are the most widely used form of strain-driven energy harvesting, which uses piezoelectric materials. Although researchers are constantly seeking improved power output from cantilever-beam-driven piezoelectric energy harvesters, a systematic and fundamental analysis of the effect of beam geometry on the power capacity of energy harvesters warrants further investigation. Most of the previous research accounts for beams that are fully coated with piezoelectric material. While a larger coating area increases energy output, it also escalates costs as piezoelectric materials are very expensive. Considering the high cost of piezoelectric materials when dealing with limited piezoelectric material, enhancing power output can be achieved by employing a larger base beam and coating a portion of it at the fixed end. As such, the aim of this work is to investigate a wide variety of cantilever beam shapes (e.g., trapezoidal, triangular, V-cut, concave, and convex) with partial piezoelectric material coating on the base beam to maximize the power output capacity of the harvester. To ascertain a comparable argument, the surface area, volume, and mass of all the considered beam shapes are kept consistent, as these parameters influence the power output of the harvester. The geometry of each shape is systematically varied to understand the effect of geometric configuration on the output power density. Finally, the power capacities of all types of beams are compared, and a design is proposed to obtain the maximum power output. It was found that when the surface area of both the beam and piezoelectric material is kept constant and piezoelectric material is located at the fixed end, a trapezoidal beam with a smaller base width and larger free end width is the most efficient in generating power as long as the structural integrity is maintained. The finding is completely opposite as was suggested by previous studies, which proposed that a trapezoidal beam with a smaller free end yields higher output. Instead, this study demonstrates that an inverted trapezoidal beam produced higher output, considering partial coating compared to the full beam coating used in previous studies. Additionally, a correlation is presented on how the beam resonance frequency shifts with variation in beam parameters.

In this paper the attention is focused on the analysis and the optimization of energy flows in networked systems via a fluid-dynamic model. In particular, a cost functional that represents a term proportional to the kinetic energy of an energy system is studied. First, the functional is optimized for a simple network having a unique node, with an incoming arc and two outgoing ones. The optimization deals with distribution coefficients and explicit solutions are found. Then, the global optimization is obtained using the local optimal parameters at the various nodes of the system. Considering the case study of an energy hub, interesting results are obtained for the whole network, proving the correctness of the proposed approach.

Hydrogen-bond (H-bond) energies in 310-helices of short alanine peptides were systematically examined by precise DFT calculations with the negative fragmentation approach (NFA), a modified method based on the molecular tailoring approach. The contribution of each H-bond was evaluated in detail from the 310-helical conformation of total energies (whole helical model; WH3-10 model), and the results were compared with the property of H-bond in a-helix from our previous study. The H-bond energies of the WH3-10 model exhibited tendencies different from those exhibited by the -helix, in that they depended on the helical position of the relevant H-bond pair. H-bond pairs adjacent to the terminal H-bond pairs were observed to be strongly destabilized. The analysis of electronic structures indicated that structural characteristics cause the destabilization of the H-bond in 310-helices. We also found that the longer the helix length, the more stable the H-bond in the terminal pairs of the WH3-10 model, suggesting the action of H-bond cooperativity.

Climate change has become a global nightmare, and the awareness of the causes of carbon emissions have resulted in rigorous studies. These studies linked the increase in global warming with booming economic growth. Since global warming has become more apparent, researchers have explored ways to decouple economic activities from carbon growth. Economic and carbon growth must be decoupled to achieve a low-carbon economy to support the carbon growth plan or emission reduction strategy. The world is transitioning towards a carbon-neutral and green ecosystem, so finding ways to decouple carbon emissions from economic activities is an exciting topic to explore. The study reviews current information on the importance of decoupling energy from economic growth innovative techniques that thoroughly examine the challenges and constraints of low-carbon energy systems. This review revealed that decarbonization and dematerialization had been achieved without declining global economic growth. It also provides information on energy use and economic activities leading to global carbon emissions and alternative solutions to the global challenge of climate change. The decoupling methods commonly used to determine the impact of energy decarbonization on economic growth are explored. All suggested that economic growth is a primary mover of global carbon emission increase and must be separated to achieve a carbon environment.

Heterometallic rare-earth clusters have garnered much attention because of their interest-ing solid-state structures and versatile applications in catalysis and material and polymer chemistry over the last four decades. Particular interest is rare earth–transition metal co-ordination compounds that behave as single-molecule magnets (SMMs) because of their potential use in information storage, spintronic devices, and magnetic refrigeration sys-tems. Another implementation involves using lanthanide clusters in luminescent-based sensing for environmental protection and security screening or in photocatalytic energy conversion reactions. Heterometallic rare earth complexes offer the promise of catalytic performance of many organic reactions due to their high oxygenophilicity, Lewis acidity, high coordination numbers, and ability to change the coordination environment quickly. Therefore, they are commonly applied as catalysts in asymmetric synthesis, oxidation re-actions, and CO2 conversions or as initiators in ring-opening polymerization and copoly-merization of cyclic monomers. They are also attractive single-source molecular precur-sors for functional inorganic materials. This review focused on the unique features and properties of the heterometallic rare earth complexes, which are closely correlated with their molecular structure. Our summary is a valuable resource, providing researchers with an insightful exploration of the heterometallic rare-earth complexes that demonstrated multimetallic synergy and cooperativity effects in various applications.

Distributed Energy Resources might have a severe influence on Power Line Communications, as they can generate interfering signals and high frequency emissions or supraharmonics that may cause loss of metering and control data. In this paper, the influence of various energy resources on Narrowband Power Line Communications is described and analyzed through several test measurements performed in a real microgrid. Accordingly, the paper describes the effects on smart metering communications through MAC layer analysis. Results show that the commutation frequency of inverters and the presence of battery chargers are remarkable sources of disturbance in low voltage distribution networks. In this sense, the results presented can contribute to efforts towards standardization and normative of emissions at higher frequencies higher, such as CENELEC EN 50160 and IEC/TS 62749.

In the same way as the realization of some of the famous gedanken experiments imagined by the founding fathers of quantum mechanics has recently led to the current renewal of the interpretation of quantum physics, it seems that the most recent progresses of observational astrophysics can be interpreted as the realization of some cosmological gedanken experiments such as the removal from the universe of the whole visible matter or the cosmic time travel leading to a new cosmological standard model. This standard model involves two dark components of the universe, dark energy and dark matter. Whereas dark energy is usually associated with the cosmological constant, we propose to explain dark matter as a pure QCD effect, namely a gluonic Bose Einstein condensate, following the transition from the quark gluon plasma phase to the colorless hadronic phase. Our approach not only allows us to assume a ratio Dark/Visible equal to 11/2 but also provides gluons and (anti-)quarks with an extra mass of vibrational nature. Such an interpretation would comfort the idea that, apart from the violation of the matter/antimatter symmetry satisfying the Sakharov’s conditions, the reconciliation of particle physics and cosmology needs not the recourse to any ad hoc fields, particles or hidden variables.

Scientific studies on the impact of wood species on solid fuel production, performance, and sustainability are grossly inadequate. The knowledge of this is imperative as users of solid fuels are increasing rapidly, especially in Africa. On this note, it becomes necessary to explore measures that will improve its efficiency and sustainability as an energy source. This study investigates some properties of selected wood species used as an energy source in Nigeria and their pelleting potential. Nine (9) samples were characterized and assessed for suitability of pelleting following four wood pellet quality standards. The findings revealed Anogeissus leiocarpus as the species with the best rating score in terms of fuel properties while Vitellaria paradoxa as the lowest. However, in terms of conformity with the four wood pellets standards, Khaya senegalensis, Parkia biglobosa and Anogeissus leiocarpus having presented density, calorific value, sulfur, arsenic, cadmium, and lead within the limits of the wood pellet quality standards were considered the best wood species in terms of fuel suitability and pelleting potential. The findings therefore suggest that not all wood species are suitable as fuel. Thus, for species that do not meet the standard wood pellet requirements, alternatives such as the use of biomass blends, additives, or process adjustments can be employed to adapt the quality to the standards or by using the fuels in improved cookstoves.

We present a new interpretation of the Higgs field as a composite particle made up of a positive, with, a negative mass Planck particle. According to the Winterberg hypothesis, space, i.e., the vacuum, consists of both positive and negative physical massive particles, which he called planckions, interacting through strong superfluid forces. In our composite model for the Higgs boson, there is an intrinsic length scale associated with the vacuum, different from the one introduced by Winterberg, where, when the vacuum is in a perfectly balanced state, the number density of positive Planck particles equals the number density of negative Planck particles. Due to the mass compensating effect, the vacuum thus appears massless, charge-less, without pressure, energy density, or entropy. However, a situation can arise where there is an effective mass density imbalance due to the two species of Planck particle not matching in terms of populations, within their respective excited energy states. This does not require the physical addition or removal of either positive or negative Planck particles, within a given region of space, as originally thought. Ordinary matter, dark matter, and dark energy can thus be given a new interpretation as residual vacuum energies within the context of a greater vacuum, where the populations of the positive and negative energy states exactly balance. In the present epoch, it is estimated that the dark energy number density imbalance amounts to, , per cubic meter, when cosmic distance scales in excess of, , are considered. Compared to a strictly balanced vacuum, where we estimate that the positive, and the negative Planck number density, is of the order, particles per cubic meter, the above is a very small perturbation. This slight imbalance, we argue, would dramatically alleviate, if not altogether eliminate, the long standing cosmological constant problem.

In general, a superconductor has zero resistance, although it requires significant refrigeration or high pressures with high manufacturing costs, which prevents it into practical applications. In other words, solving these issues implies main superconducting researches. To solve these problems, this paper describes a new type of superconductivity, which is independent for temperatures and which operates without pressures. The principles of the presented system are as follows:First a voltage source, a current source and a load are connected in series. Then, the voltage of the voltage source is adjusted to balance the voltage of the load. Under this condition, the balance of the two voltages provides a zero voltage between the taps of the current source and the generated current from the voltage source becomes zero because of the internal infinite resistance of the current source. As a result, the electric powers generated by the two sources are zero, and therefore, the load cannot generate Joule heating because of energy conservation. However, the current from the current source (not the voltage source) is not zero; therefore, we can predict that the resistance of the load must be zero. As a theory, we derived a new electric field and transient attractive force, which result in a very short coherence of an electron pair because there is not the Coulomb repulsive force due to the existence of the above transient attractive force. Note that both the forces are derived by the Poisson equation, which implies that they cannot be compatible. Therefore, the pair combination energy from spins becomes extremely strong, which is not destroyed by the normal heat energy. Moreover, every center-of-mass motion of electron pair results in the Bose-Einstein condensation and the macroscopic wave function, which produces the London equation (i.e., the Meissner effect). Moreover, by introducing the equivalent circuit, this paper conducted numerical calculations. As a result, we could derive numerically zero resistance and responses for additional static magnetic fields as a discharged current, which implies the Meissner effect. Note that this paper has prepared Appendix section, which provides a guide to reproduce actual experiments and preliminary experimental results. These results in the Appendix indicate the zero resistances and Meissner effects.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

This research aimed to investigate the relationship between climate policy uncertainty (CPU), clean energy (ENERGY), carbon emission allowance prices (CARBON), and Bitcoin returns (BTC) for the period from August 2012 to August 2022. The empirical analysis strategies utilized in this study included the Fourier Bootstrap ARDL long-term coefficient estimator, Fourier Granger Causality, and Fourier Toda Yamamoto Causality methods. Following the confirmation of cointegration among the variables, we observed a positive relationship between BTC and CARBON, a positive relationship between BTC and CPU, and a negative relationship between BTC and ENERGY. In terms of causal associations, we identified one-way causality running from CARBON to BTC, BTC to CPU, and BTC to the ENERGY variable. The study underscores the potential benefits and revenue opportunities for investors seeking diversified investment strategies in light of climate change concerns. Furthermore, it suggests actionable strategies for policymakers, such as implementing carbon taxes and educational campaigns, to foster a transition towards clean energy sources within the cryptocurrency mining sector and thereby mitigate environmental impacts.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Due to the continued deepening of today’s mining projects, there is a need to develop new or improved rockbolts that are strong and yielding and have high energy absorption when exposed to dynamic loading. Impact tests can provide useful information about the dynamic response of rockbolts but most laboratory tests involve high costs in preparation and result validation. Numerical modeling is an alternative that, in addition to complementing laboratory results, can be used to represent the process of deformation and energy absorption of support elements. In this paper the implementation and results obtained from a finite difference (FDM) numerical model are presented. The model functions as a simulation tool to illuminate all the elements that conform the large-scale (1:1) impact test and their behavior and influence on the dynamic response of a threadbar bolt (22 mm nominal diameter). The model was calibrated using published results and based on these results as well as parametric analysis, the response of each component (steel tube, grout, and bolt) could be identified and its behavior in terms of absorbed energy and displacement could be observed. Results show the model can provide important preliminary information to make design decisions about support elements design.

I examine the groups which underly classical mechanics, non-relativistic quantum mechanics, special relativity, relativistic quantum mechanics, quantum electrodynamics, quantum flavourdynamics, quantum chromodynamics, and general relativity. This examination includes the rotations SO(2) and SO(3), the Pauli algebra, the Lorentz transformations, the Dirac algebra, and the U(1), SU(2), and SU(3) gauge transformations. I argue that general relativity must be generalized to Einstein-Cartan theory, so that Dirac spinors can be described within the framework of gravitation theory.

As the world’s second largest economy, China ranks amount the world’s top nations when it comes to carbon emission, and therefore its attitude towards climate change is closely followed by all parties concerned. There have been few researches on the role of environmental governance in low-carbon city transformation process, especially the Chinese one. This paper analyses the role of government environmental regulation played in the low-carbon city transformation process by taking Shenzhen as the research object. One of the world's youngest super cities, it also happens to be the lowest carbon emission intensity city in China. Striving to explore green low-carbon development path for the whole country, Shenzhen provides practical experience for countries to cope with global climate change. However, its efforts to reduce the total carbon emissions failed, but it emphasized the carbon emission intensity, which is consistent with the international commitments made by the central government. China’s policy towards handling climate change relies on hierarchical governance arrangement. The strength of the NGOs in the country is weak and incomparable with the government’s, which has mastered most of the resources and is just a reality in China.

To stabilize the Earth’s climate a large-scale transition is needed to non-carbon emitting renewable energy technologies like wind and solar energy. Although these renewable energy sources are now lower-cost than fossil fuels, their inherent intermittency make them unable to supply a constant load without storage. To address these challenges rechargeable electric batteries are currently the most promising option; however, their high capital costs limit current deployment velocities. To both reduce the cost as well as improve performance 3D printing technology has emerged as a promising solution. This literature review provides the state-of-the-art enhancements of battery properties with 3D printing including efficiency, mechanical stability, energy and power density, customizability and sizing, production process efficiency, material conservation and environmental sustainability as well as the progress in solid-state batteries. The principles, advantages, limitations, and recent advancements associated with the most common types of 3D printing are reviewed focusing on their contributions to the battery field. 3D printing batteries offer design flexibility, material flexibility, reduces pack weight, minimizes material waste, increases the range of applications and has the potential to reduce costs. As 3D printing technologies become more accessible, the prospect of cost-effective production for customized batteries is extremely promising.

The process of modelling energy systems is accompanied by challenges inherently connected with mathematical modelling. However, due to modern realities in the 21st century, existing challenges are gaining in magnitude and are supplemented with new ones. Modellers are confronted with a rising complexity of energy systems and high uncertainties on different levels. In addition, interdisciplinary modelling is necessary for getting insight in mechanisms of an integrated world. At the same time models need to meet scientific standards as public acceptance becomes increasingly important. In this intricate environment model application as well as result communication and interpretation is also getting more difficult. In this paper we present the open energy modelling framework (oemof) as a novel approach for energy system modelling and derive its contribution to existing challenges. Therefore, based on literature review, we outline challenges for energy system modelling as well as existing and emerging approaches. Based on a description of the philosophy and elementary structural elements of oemof, a qualitative analysis of the framework with regard to the challenges is undertaken. Inherent features of oemof such as the open source, open data, non-proprietary and collaborative modelling approach are preconditions to meet modern realities of energy modelling. Additionally, a generic basis with an object-oriented implementation allows to tackle challenges related to complexity of highly integrated future energy systems and sets the foundation to address uncertainty in the future. Experiences from the collaborative modelling approach can enrich interdisciplinary modelling activities. Our analysis concludes that there are remaining challenges that can neither be tackled by a model nor a modelling framework. Among these are problems connected to result communication and interpretation.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

There is a need to find methods to intensify the anaerobic digestion process. One possibility is the use of pre-treatment techniques. Many laboratory tests confirm their effectiveness, but in most cases, there is no verification work carried out on industrial plants. The aim of the research carried out under laboratory conditions and on a large scale was to determine the technological and energy efficiency of the use of hydrodynamic cavitation in the pre-treatment of a waste mixture from dairy farms. It has been shown that hydrodynamic cavitation significantly increases the concentration of organic compounds in the dissolved phase. In the most effective variants, the increase in the content of these indicators was over 90% for both COD and TOC. The degree of solubilisation achieved was 49±2.6% for COD and almost 52±4.4% for TOC. Under laboratory conditions, the highest effects of anaerobic digestion were achieved after 10 minutes of pre-treatment. The amount of biogas was on average 367±18 mL/gCOD and the amount of methane 233±13 mL/gCOD. Further large-scale optimisation trials showed that after 8 minutes of hydrodynamic cavitation, the biogas yield was 327±8 L/kgCOD with a CH4 content of 62.9±1.9%. With this variant, the net energy yield was 66.4±2.6 kWh/day, a value that was 13.9% higher than the original variant with 10 minutes of disintegration and 3.1% higher than the variant without pre-treatment.

The expansion of renewable energies is progressing strongly. The influence on the power supply networks by the volatility of the infeed must be met with new concepts. In this paper we investigate the possibilities of integrating microgrids as a cooperating unit in the power supply network to support further expansion of RES power plants. In this paper a differentiation of microgrids from similar network structures is established, a classification of proposed groups is made. Then, after the description of simulation of components in a microgrid, with practical advice, an example model is shown, which aids the dimensioning of the components within a microgrid to achieve a specified goal.

Although general relativity has been successful in explaining many astronomical phenomena, few problems about the contents and evolution of the universe have remained mysterious since last century. Most important of them is the cosmological constant problem in which conventional calculation of vacuum (or dark) energy density using quantum mechanics leads to a value ~10¹¹⁴ J/m³ which is ~10¹²³ times more than the vacuum energy (5.3×10^-10 J/m³) estimated from astronomical observations of expanding universe. Similarly, cosmic coincidence problem questions why the matter energy density (ordinary plus dark matter) is of the same order as the vacuum energy density at present time. Finally, the mechanism responsible for spatial flatness and expansion of the universe are not clearly understood. In this paper, by taking the vacuum as a finite and closed quantum oscillator, we solve all of the above-mentioned problems. At first, by using purely quantum mechanical approach, we predict that the dark energy density is c⁴/(GR²) = 5.27×10^-10 J/m³ (where R is radius of 3-sphere of universe) and matter energy density is c⁴/(2GR²) = 2.6×10^-10 J/m³ which match well with astronomical observations. We also prove that the dark energy has always been ~66.7% and matter energy has been ~33.3% of total energy and hence, the so called cosmic coincidence problem doesn’t exist. Next, we show how flatness of space could be maintained since the early stage of universe. Finally, using our model, we derive the expression for age and radius of universe which match well with the astronomical data.

This article presents multiple novel and compelling arguments to systematically disprove two widely accepted notions: one is that entropy is a measure of disorder, and the other is Schrödinger's notion of negative entropy (negentropy). These two notions have been cited hundreds of times annually in scientific literature for decades. To mathematically describe the second law of thermodynamics, the concept of entropy was created and defined in the 1860s as heat energy divided by thermodynamic temperature, and the entropy of an object increases when it absorbs heat. This is the uncontroversial and fundamental nature of entropy, which is pivotal to current thermodynamics and from which multiple facts are deduced. These facts consistently disprove the above two notions. Some biological facts, such as the one that life orderliness is encoded and provided by inherited genes rather than entropy decline, can also disprove Schrödinger's negentropy notion. Moreover, this article further clarifies the reasoning errors of the two notions. It also shows that the tendency of many natural or social systems to become more disordered over time does not result from the second law of thermodynamics.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

Maxwell's electric equation and Schrödinger quantum equation are used to find useful expressions for the probability of electrons existence and the electrons transport. The first expression which uses special relatively also shows that the probability of the electrons existence is higher for lower energy states compared to higher energy states where the probability is low. This means that electrons transport takes place from higher energy states to lower states. This conforms to the laws of chemistry where the atom tends to be stable by forcing electrons to occupy lower energy states. The second expression used the momentum velocity relation instead of special relatively. This expression shows also electrons transport from higher to lower states. It also shows that the probability of the electrons existence is higher for lower electrons density regions and lower for higher electrons density regions. This means that the electrons transport is from higher density regions to lower density regions. This conforms to the diffusion law.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

Photovoltaic shading devices (PVSDs) have the dual function of providing shade and generating electricity, which can reduce building energy consumption and improve indoor daylighting levels. This study adopts a parametric performance design method and establishes a one-click simulation process by using the Grasshopper platform and Ladybugtools. The research focuses on the effect of dynamic PVSDs on daylighting and energy consumption in an office building in Qingdao. Through simulation, the study calculates the monthly energy consumption and useful daylight illuminance (UDI) under different inclination angles and installation heights of PVSDs. And the optimal configuration of PVSDs for each month under three dynamic strategies (rotation, sliding, and hybrid) is determined. Additionally, different control strategies and fixed PVSDs are compared to clarify the impact of various control strategies on daylighting and energy consumption. The findings reveal that, compared to no shading, dynamic PVSDs in rotation strategy (with an installation height of 0 m), sliding strategy (with an inclination angle of 20°), and hybrid strategy can achieve energy savings of 32.13%, 47.22%, and 50.38%, respectively. They can increase the annual average UDI by 1.39%, 2.8%, and 3.1%, respectively.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

Camelina (Camelina sativa L.) is an oilseed with potential for use as a raw material in second-generation biofuels. Camelina has a seed yield of up to 2380 kg ha^-1 and contains around 45% fatty acids. Selection of a suitable site is critical for production optimization. The objective of this study was to determine Chilean agro-climatic suitability for establishing camelina as a productive alternative. Climate and soil requirements and geographical restraints were evaluated for the species, considering the climatological characteristics of its regions of origin, as well as regions where camelina is successfully grown in the rest of the world. The variables considered include factors (maximum temperatures of the warmest month, water deficits, and degree days) and limitations (altitude, geomorphology, and current land use), which permitted the evaluation of the national territory for a certain level of suitability. It was determined that 1.3% of the national territory (960,664 ha) has some degree of suitability for camelina adoption. Between the Biobío and Los Lagos regions, 49.0% of land (471,203 ha) is in the category of without thermic restrictions, with mild water restrictions, and mild soil restrictions or without information, which can be used for camelina production. The Los Ríos region had 21.4% surface area (321,176 ha) with some level of suitability for camelina, the most suitable region to establish this crop in Chile.

NiV2O6 thin films were grown on glass slides with varying thicknesses using the nebulizer spray pyrolysis. The impact of thickness on the thin films' optical, structural, morphological, and electrical characteristics was systematically investigated. The X-ray diffraction and micro-Raman analysis confirmed the formation of the triclinic NiV2O6 system. Surface morphology and roughness variations in the as-deposited NiV2O6 films were studied using scanning electron microscopy (SEM) and a profilometer. Optical properties, including optical band gap (Eg), extinction coefficient (k), absorption coefficient (α), and refractive index (n), were determined through optical reflectance and transmittance measurements. The optical energy gap of the as-deposited NiV2O6 films decreased from 2.3 eV to 1.9 eV with increased layer thickness. Furthermore, the photo-detectivity of the films demonstrated an enhancement corresponding to the prolonged spray time. The sensitivity values obtained for visible irradiation are 328, 511, and 433 for samples S1, S2, and S3, respectively. The obtained results are imputed to the specific porous microstructure.

We propose a model for gravity based on the gravitational polarization of space. With this model, we can relate the density parameters within the Friedmann model, and show that dark matter is bound mass formed from massive dipoles set up within the vacuum surrounding ordinary matter. Aggregate matter induces a gravitational field within the surrounding space, which reinforces the original field. Dark energy, on the other hand, is the energy density associated with gravitational fields both for ordinary matter, and bound, or induced dipole matter. At high CBR temperatures, the cosmic susceptibility, induced by ordinary matter vanishes, as it is a smeared or average value for the cosmos as a whole. Even though gravitational dipoles do exist, no large scale alignment or ordering is possible. Our model assumes that space, i.e., the vacuum, is filled with a vast assembly (sea) of positive and negative mass particles having Planck mass, called planckions, which is based on extensive work by Winterberg. These original particles form a very stiff two component superfluid, where positive and negative mass species neutralize one another already at the submicroscopic level, leading to zero net mass, zero net gravitational pressure, and zero net entropy, for the undisturbed medium. It is theorized that the gravitational dipoles form from such material positive and negative particles, and moreover, this causes an intrinsic polarization of the vacuum for the universe as a whole. We calculate that in the present epoch, the smeared or average susceptibility of the cosmos equals, , and the overall resulting polarization equals, . Moreover, due to all the ordinary mass in the universe, made up of quarks and leptons, we calculate a net gravitational field having magnitude, . This smeared or average value permeates all of space, and can be deduced by any observer, irrespective of location within the universe. This net gravitational field is forced upon us by Gauss’s law, and although technically a surface gravitational field, it is argued that this surface, smeared value holds point for point in the observable universe. A complete theory of gravitational polarization is presented. In contrast to electrostatics, gravistatics leads to anti-screening of the original source field, increasing the original value, , to, , where is the induced or polarized field. In the present epoch, this leads to a bound mass, , where is the sum of all ordinary source matter in the universe, and equals the relative permittivity. A new radius, and new mass, for the observable universe is dictated by the density parameters in Friedmann's equation, and Gauss’s law. These lead to the very precise values, , and, , respectively, somewhat larger than current less accurate estimates.

In this paper, modelling, simulation and verification of multi-agent manufacturing system with application of bio-inspired techniques are addressed. To this end, the new solution of abstract architecture for control and coordination decentralized systems - CODESA is suggested. Centralized architecture suffers from various problems, such as rigidity, scalability, low fault-tolerance or very limited flexibility, agility, energy efficiency and productivity. Prime is concrete application of CODESA in manufacturing domain. The undesirable characteristics of emergent behaviour are the problem to achieve optimization and impossibility to predict future states of the system. CODESA-Prime has been tested by simulations for automatic guided vehicle (AGV) systems guided by magnetic tape in Ella Software Platform.

The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

This hypothesis is the result of my conviction that science will oneday prove everything in space and time is part of a unification. In "A Brief History of Time", Stephen Hawking wrote, "If everything in the universe depends on everything else in a fundamental way, it might be impossible to get close to a full solution (of the universe's puzzles) by investigating parts of the problem (such as general relativity and quantum mechanics) in isolation." The goal: to establish a “proof of concept” to which equations can be added. It’s concluded the Steady State, Big Bang, Inflation and Multiverse theories all ultimately fail and a topological model including bits (binary digits), Mobius strips, figure-8 Klein bottles and Wick rotation works better. The failed cosmologies have impressive points leading to the idea that they’re all necessary stepping-stones. For example, the Big Bang is seen here as violation of the 1st Law of Thermodynamics but its supposed origin from quantum fluctuations is reminiscent of bits switching between 1 and 0. The topological hypothesis has potential to explain dark matter, dark energy, and electromagnetic-gravitational union. Finally, the article introduces what is called vector-tensor-scalar geometry - and extensions of Einstein's Gravity and Maxwell's Electromagnetism.

The transition to sustainable energy systems in the Middle East and North Africa (MENA) region addresses critical challenges of environmental protection, energy security, and socio-economic resilience. Using neo-institutional theory, this paper examines the intricate relationship between formal and informal institutions and their significant impact on the region’s energy transition. Despite the MENA region’s abundant renewable energy resources, numerous institutional barriers, such as governance inefficiencies, regulatory inconsistencies, and entrenched socio-cultural norms, significantly hinder this transition. Through a review of existing literature, this study presents a comprehensive analytical framework designed to overcome these barriers, with a focus on the Just and Sustainable Energy Transition model. This strategic model emphasizes equity, sustainability, and inclusive governance as pillars for reform. The study offers detailed recommendations for institutional change and underscores the importance of collaborative efforts among governments, industry stakeholders, and international partners to unlock the MENA region’s renewable energy potential, advance global sustainability goals, and ensure a more secure and resilient energy future.

Keywords: Energy harvesting, Hybrid, Medical Wearable Sensor Nodes, Health Monitoring, Power Management

Despite achieving over 90% household service coverage, the Latin American and Caribbean region faces energy poverty (EP) challenges, particularly in rural areas. With growing GDP and foreign investments, Panama grapples with significant energy inequality, ranking poorly in clean energy access. Almost 177,000 Panamanians experience energy poverty, impacting their quality of life. This study proposes a Multidimensional Energy Poverty Index for Panama (MEPIP), considering dimensions like lighting, cooking, food refrigeration, thermal comfort, and knowledge/communication. MEPIP, inspired by indicators from Chile, Mexico, and the UK, aims to provide a nuanced understanding of EP. Results from surveyed rural communities, Guásimo, Llano Grande Abajo, Los Aguilares, and La Tranquilla, reveal pervasive energy poverty, emphasizing the urgency of targeted interventions. MEPIP's application identifies critical areas, such as Llano Grande Abajo, highlighting stark inequalities and the need for comprehensive energy policies to address EP in Panama.

We suggest that momentum should be redened in order to help make physics more consistent and more logical. In this paper, we propose that there is a rest-mass momentum, a kinetic momentum, and a total momentum. This leads directly to a simpler relativistic energy momentum relation. As we point out, it is the Compton wavelength that is the true wavelength for matter; the de Broglie wavelength is mostly a mathematical artifact. This observation also leads us to a new relativistic wave equation and a new and likely better QM. Better in terms of being much more consistent and simpler to understand from a logical perspective.

It is already known that a simple nonlocal de Sitter gravity model, which we denote as dS gravity, contains an exact vacuum cosmological solution which mimics dark energy and dark matter and is in very good agreement with the standard model of cosmology. This success of dS gravity motivated us to investigate how it works at lower than cosmic scale – galactic and the solar system. This paper contains our investigation of the corresponding Schwarzschild-de Sitter metric of the dS gravity model. To get exact solution, it is necessary to solve the corresponding nonlinear differential equation, what is a very complicated and difficult problem. What we obtained is a solution of linearized equation, which is related to space metric far from the massive body, where gravitational field is weak. The obtained approximate solution is of particular interest for examining the possible role of non-local de Sitter gravity dS in describing the effects in galactic dynamics that are usually attributed to dark matter. The solution has been tested on the Milky Way and the spiral galaxy M33 and is in good agreement with observational measurements.

Previously reported atomic data (spectral lines, wavelengths, energy levels, and transition probabilities) have been collected and systematically analyzed for the Cs VI. The present theoretical analysis is supported by extensive calculations made for Cs VI with a pseudo-relativistic Hartree--Fock (HFR) method together with the superposition of configuration interactions implemented in Cowan's codes. In this critical evaluation, we provided several possibly observable lines with Ritz-wavelengths, computed from the optimized energy levels, and theoretical transition probabilities with their estimated uncertainties. In addition, we provided the radiative transition parameters for several forbidden lines within the ground configuration $5s^25p^2$ of Cs VI.

Entropy generation, formulated by combining the first and second laws of thermodynamics with an appropriate thermodynamic potential, emerges as the difference between a phenomenological entropy function and a reversible entropy function. The phenomenological entropy function is evaluated over an irreversible path through thermodynamic state space via real time measurements of thermodynamic states. The reversible entropy function is calculated along an ideal reversible path through the same state space. Entropy generation models for various classes of systems—thermal, externally loaded, internally reactive, open and closed––are developed via selection of suitable thermodynamic potentials. Here we simplify thermodynamic principles to specify convenient and consistently accurate system governing equations and characterization models. The formulations introduce a new and universal Phenomenological Entropy Generation (PEG) theorem. The systems and methods presented––and demonstrated on grease degradation, battery charging and discharging, metal fatigue and pump flow––can be used for design, analysis, and support of diagnostic monitoring and optimization.

Rapid increase in urbanization and industrialization due to increase in human population has led to increase in global warming resulting to climate change that affects the ecosystem. Unusual natural disasters such as cyclones, storms, floods, weather fluctuations, rising seal levels, transitional ecosystems and coastal disruptions are major adverse effects of climate change. There are huge worrisome concerns and uncertainties about the future of the planet earth due to climate change caused by high carbon emissions. Global aggressive policies in control of Carbon-dioxide (CO2) emissions from several combustion mechanisms have paved way for alternative/ clean energy sources. Green hydrogen is a promising means of clean energy sources for commercial power generation stations and other crucial systems such as hydrogen fuel cell vehicles (HFCVs) , motors, drives, backup power for buildings, and also serving as a source of electrical energy for remote locations. The goal of this study is to review the current level of Sub-Saharan African nations’ preparedness to adopt green hydrogen as a way to mitigate local energy supply issues and strengthen their individual economies.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

Microgrids (MGs) have evolved as critical components of modern energy distribution networks, providing increased dependability, efficiency, and sustainability. Effective control strategies are essential for optimising MG operation and maintaining stability in the face of changing environmental and load conditions. Traditional rule-based control systems are extensively used due to their interpretability and simplicity. However, these strategies frequently lack the flexibility for complex and changing system dynamics. This paper provides a novel method called hybrid intelligent control for adaptive MG that integrates basic rule-based-control and deep learning techniques, including gated recurrent units (GRU), basic recurrent neural network (RNN) and long short-term memory (LSTM). The main target of this hybrid approach is to improve MG management performance by combining the strengths of basic rule-based systems and deep learning techniques. These deep learning techniques readily enhance and adapt control decisions based on historical data and domain-specific rules, leading to increasing system efficiency, stability, and resilience in adaptive MG. Our results show that the proposed method optimises MG operation, especially under demanding conditions such as variable renewable energy supply and unanticipated load fluctuations. This study investigates special RNN architectures and hyper-parameter optimization techniques with the aim of predicting power consumption and generation within the adaptive MG system. Our promising results show the highest-performing models indicating high accuracy and efficiency in power prediction. The finest-performing model accomplishes an R2 value close to 1, representing a strong correlation between predicted and actual power values.

Distribution System Operators (DSOs) are adapting to changing energy demands and the shift toward renewable and decentralized energy. Circularity is increasingly relevant for DSOs as their distribution systems age and need replacing. Taking circular action, however, is generally regarded as challenging as the current circular economy (CE) landscape is highly fragmented and rarely touches the implementation level. A longitudinal case study at Dutch DSO Liander on the circu-larity of distribution transformers was used to understand empirical success factors for taking circular action and to generate prescriptive knowledge on the operationalization of circularity. Six design propositions for circular action were formulated that suggest to 1) initiate small-scale cir-cularity experiments, 2) involve technical and strategic experts, 3) synergize circularity with more urgent, primary goals 4) translate circular initiatives bottom-up and top-down, 5) collaborate with other DSOs, and 6) create multidisciplinary teams. At DSO Liander, selecting the right interventions depending on the changing context contributed to operationalizing circularity for distribution transformers and achieving circularity targets. The generalizable design propositions could assist other DSOs in optimizing their strategy toward circular action.

The main source of electricity worldwide stems from fossil fuels, contributing to air pollution, global warming, and associated adverse effects. This study explores wind energy as a potential alternative. Nevertheless, the variable nature of wind introduces uncertainty in its reliability. Thus, it is necessary to identify an appropriate machine learning model capable of reliably forecasting wind speed under various environmental conditions. This research compares the effectiveness of artificial neural networks (ANN) and convolutional neural networks (CNN) in predicting wind speed across three locations in South Africa, characterised by different weather patterns. Empirical results show that CNN outperforms ANN in accurately forecasting wind speed under different weather conditions. This superiority is likely due to the inherent architectural attributes of CNNs, including feature extraction capabilities, spatial hierarchy learning, and resilience to spatial variability. These results could be useful to decision-makers in the energy sector.

Herein is introduced a simple scalar field model derived from classical based kinetic energy, gravitational potential energy, and Special Relativity’s rest mass energy. By applying a classical orbit over the scalar field, relativistic effects are predicted. The scalar field is then applied to a classical model of the Hydrogen atom resulting in a relativistic effect equal to the binding energy of the Hydrogen atom. In addition, the model derives the fine structure constant due to the gravitational effect. The relativistic effects are then discretized in increments equal to the model’s gravitational induced constant. The discretization produces the Hydrogen atom spectral emissions and an angular moment equal to Planck’s reduced constant. The model is not presented as a replacement for current theory, rather it is for inspection and illustration of how a simplistic model may offer a fundamental bridge between the more complex, time proven theories of General Relativity and Quantum Mechanics.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

Abstract: Field studies with large-stemmed plants Artemisia dubia (wormwood) have been carried out at Vėžaičiai Branch LAMMC since 2018. According to three years of experimental results, annual dry matter (DM) yield varied from 7.94 to 10.14 t ha-1. Growing conditions, nitrogen ap-plication level and harvesting time had significant impacts on Artemisia dubia productivity. This article presents the results of research on preparation and use of Artemisia dubia biomass for en-ergy conversion and evaluation of technological-technical and environmental parameters of these plants utilization for solid biofuel. For experiments were used 6 variants of Artemisia dubia samples, which were grown in 2021: plants were cut three times and two fertilization options were used: (1) no fertilization and (2) fertilization with 180 kg ha-1 of nitrogen fertilizer. These harvested plants were chopped, milled and were pressed into the pellets. The physi-cal-mechanical characteristics (mоisture content, density and strength) of Artemisia dubia pellets were investigated. During this study, it was found that the density in dry mass (DM) of pellets ranged from 1119.86 to 1192.44 kg m-3. The pellet moisture content ranged from 8.80 to 10.49%. After testing of pellet strength, it was found that the pellets which were made from plant bio-mass PK-1-1, were the most resistant to compression, they withstood 560.36 N of pressure. Dry fuel lower heating value (LHV) of pellets was sufficiently high and was very close to pine saw-dust pellets, it varied from 17.46±0.25 MJ kg-1 to 18.14±0.28 MJ kg-1. The ash content of burned pellets ranged from 3.62±0.02% to 6.47±0.09%. Emissions of harmful pollutants – CO2, CO, NOx and unburnt hydrocarbons (CxHy) did not exceed the maximum permissible levels. Summariz-ing the results of investigated properties, cоmbustion and emissiоns of Artemisia dubia pellets, it can be concluded that this biofuel can be used for production of pressed biofuel and it is charac-terized by sufficient high quality, efficient combustion and permissible emissions to the envi-ronment.

Observation of the distribution of the velocity of galactic rotation curves differed from their expected centripetal form and lead to the notion of Dark Matter or modifications to Newtonian and General Relativity, such as MOND, TeVeS and the like and even Quantised Inertia. We aim to show that General Relativity with Dark Energy/the Cosmological Constant is all that is needed, with the proviso that the Cosmological Constant can increase in the presence of a light flux or some other factor from galaxies and become gravitating; the need for Dark Matter may be abated.

The transport and entanglement of photons is becoming prominent in optics applied to information and quantum computing, where the angular momentum of light stands out in the exchange and inversion of quantized states, with prospects for several technological applications, such as the transport and storage of quantum information. In order to contribute to the understanding of quantized states in photon-matter interaction, we describe a quantized state equation in multidimensional Hilbert space for the diagnosis of OAM states, where probabilities arise in a relativistic setting. It was found that the classical-relativistic variability of the probabilities constitutes a resultant capable of describing the quantized states of light, where the state variable is the variation of the angular momentum of the photon, capable of estimating the orbital angular momentum inversion points at angular incidence. It was found that the chances of finding the quantized states of light at angular incidence can be treated by purely relativistic probabilities, explaining that when both states have equal chances of being found and the angular momentum variation is zero, the source-observer synchronizations occur at the step of increasing relativistic regime of the photon dynamics. We found that the relativistic effect from the perspective of the source referential is able to alter the chances of an event occurring, dilating and contracting the probabilities of finding a quantized state of light at angular incidence.

In the current complex and uncertain macroeconomic situation, improving the inherent resilience of the new energy vehicle industry chain is the key to effectively addressing various risks and challenges, and achieving dynamic balance between high-quality industrial development and industrial chain security. Based on the basic concept of resilience and the actual situation of new energy vehicle industry chain development, this study constructs a comprehensive evaluation index system for the resilience of the new energy vehicle industry chain, which includes four dimensional first-level indicators of coping resistance, adaptive resilience, autonomous control and leading competitiveness. In addition, it is measured by combining the data related to the new energy vehicle industry chain in Changzhou City. Our study shows that the situation on the new energy vehicle industry chain is complicated, and the comprehensive evaluation index system is more favorable for evaluating its resilience level.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

First, a recently developed eigenfunction expansion technique, based in part on separation of the thickness-variable and partly utilizing a modified Frobenius type series expansion technique in conjunction with the Eshelby-Stroh formalism, is employed to derive three-dimensional singular stress fields in the vicinity of the front of an interfacial crack weakening an infinite bicrystalline superlattice plate, made of orthorhombic (cubic, hexagonal and tetragonal serving as special cases) phases, of finite thickness and subjected to the far-field extension/bending, in-plane shear/twisting and anti-plane shear loadings, distributed through the thickness. Crack-face boundary and interface contact conditions as well as those that are prescribed on the top and bottom surfaces of the bicrystalline superlattice plate are exactly satisfied. It also extends a recently developed concept of lattice crack deflection (LCD) barrier to a superlattice, christened superlattice crack deflection (SCD) energy barrier for studying interfacial crack path instability, which can explain crack deflection from a difficult interface to an easier neighboring cleavage system. Additionally, the relationships of the nature (easy/easy, easy/difficult or difficult/difficult) interfacial cleavage systems based on the present solutions with the structural chemistry aspects of the component phases (such as orthorhombic, tetragonal, hexagonal as well as FCC (face centered cubic) transition metals and perovskites) of the superlattice are also investigated. Finally, results pertaining to the through-thickness variations of mode I/II/III stress intensity factors and energy release rates for symmetric hyperbolic sine distributed load and their skew-symmetric counterparts that also satisfy the boundary conditions on the top and bottom surfaces of the bicrystalline superlattice plate under investigation, also form an important part of the present investigation.

The conventional measure of cosmic acceleration, denoted as \( q \), relies heavily on the frame of reference and operates within a 3D space-like coordinate system, potentially leading to misinterpretations of underlying physics. In this study, we propose a novel measure, \( q_E \), grounded in distances between causal events in 4D null space. We compare \( q_E \) with the standard \( q \) using observational data from supernovae (SN) and radial galaxy/quasar (QSO) clustering (BAO) to find a better alignment of data with \( q_E \). Our analysis indicates that cosmic expansion, when viewed in the rest frame, is decelerating, with events confined by an Event Horizon akin to that of a Black Hole interior. Rather than invoking new dark energy or modified gravity, we propose that \( \Lambda \) corresponds to a boundary term exerting an attractive influence, analogous to a rubber band resisting further expansion and preventing horizon crossing of events. Contrary to prevailing notions, interpreting current cosmic expansion measurements as deceleration, rather than acceleration, offers a more accurate depiction of observed phenomena and the underlying physics. This reevaluation prompts further investigation into the nature of cosmic expansion, as well as the exploration of alternative frameworks and measures in cosmology.

This study deals with computational analysis of dominant fatty acid ethyl esters characterized from the biodiesel produced from waste beef tallow by means of KOH catalyzed ethanol based transesterification. Ethyl palmitate, Ethyl Oleate, Ethyl Stearate and Ethyl Myristate were identified as dominant fatty acid esters and were computed for molecular analysis in Gaussian 09 software using Density Functional Theory (B3LYP method) with 6-31G* as basis set. Geometric parameters were in accordance with existing experimental values and population analysis exhibited negative charge for oxygen atoms, both positive & negative charge for carbon atoms in all ester molecules. The molecular dipole moment was higher for unsaturated ester molecule and quadruple moment proposed electronic dislocation in X+Y direction. Also, energy gap decreased slightly with increasing carbon chain but reduced drastically with increase in unsaturation. Electrostatic potential mapping displayed negative electrostatic potential for oxygen atoms in ester linkage of all ester molecules.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

As an important support for power system with high penetration of renewable energy, energy storage system (ESS) has changed the traditional model of simultaneous implementation of electricity production and consumption, and its installed capacity under the source-grid-load scenario is rising year by year, but it faces the problems of insufficient utilization and benefits. This study analyzes the functional combination of ESS under the source-grid-load scenarios, and proposes a comprehensive benefit evaluation method of energy storage projects based on fuzzy decision-making trial and evaluation laboratory (DEMATEL) and super efficiency data envelopment analysis (DEA) model, which considers the perspective of economic and social environment. Firstly, the functional requirements of energy storage on the source-grid-load scenarios are explored respectively, and the characteristics of various functions are analyzed to form functional combination schemes. Secondly, index modeling is carried out from three aspects: the whole life cycle cost, functional combination benefit and social environmental benefit, and the comprehensive benefit evaluation index system of energy storage project is proposed, which includes both economic and social environment. Then, the intuitionistic trapezoidal fuzzy number is combined with DEMATEL to form an effective analysis method for the input-output relationship of the indexes, and the comprehensive evaluation is realized based on the super efficiency DEA model. Finally, the effectiveness of the proposed evaluation method and the rationality of the functional combination are verified under source-grid-load scenarios respectively.

A theoretical account of development in mesocortical anatomy is derived from the free energy principle, operating in a neural field with both Hebbian and anti-Hebbian neural plasticity. An elementary structural unit is proposed, in which synaptic connections at mesoscale are arranged in paired patterns with mirror symmetry. Exchanges of synaptic flux in each pattern form coupled spatial eigenmodes, and the line of mirror reflection between the paired patterns operates as a Markov blanket, so that prediction errors in exchanges between the pairs are minimized. The theoretical analysis is then compared to the outcomes from a biological model of cortical neurodevelopment, in which neuron precursors are selected by apoptosis for cell body and synaptic connections maximizing synchrony and also minimizing axonal length. It is shown that this model results in patterns of connection with the anticipated mirror symmetries, at micro-, meso- and inter-arial scales, among lateral connections, and in cortical depth, explaining the spatial organization and functional significance of neuron response preferences, and compatible with features of both columnar and noncolumnar cortex. Multi-way interactions of mirrored representations provide a preliminary anatomically realistic model of cortical information processing.

A novel concept of a finned piston system is presented and analyzed where the compression heat is continuously extracted from the compression chamber. The resulting compression characteristic moves in direction of an isothermal process, reducing so the temperature of the compressed fluid in the compression chamber and reducing the necessary mechanical work for the process. The finned piston concept consists in an integrated heat exchanger inside of the chamber and being constituated of imbricated flat fins placed on the stator part and on the mobile piston. The internal heat exchange surface is strongly increased in comparison with a classical piston/cylinder. The energetic performance of the new system is evaluated with the help of simulation. Pressures, forces and temperature of the compressed gas are simulated as well as the mechanical work needed. The different curves are compared with adiabatic and isothermal characteristics.

In this work, the author employs the quantum hydrodynamic formalism to achieve the geometrization of spacetime for describing the gravitational interaction within the framework of quantum theory. This approach allows for the development of an equation of gravity that is mathematically connected to the fermion and boson fields. This achievement is accomplished by incorporating two fundamental principles: covariance of the quantum field equations and the principle of least action. By considering these principles, a theory is established that enables the calculation of gravitational corrections to Quantum Electrodynamics, and potentially, to the standard model of particle physics as well. The theory also provides an explanation for two phenomena: the existence of a cosmological pressure density similar to quintessence, that is compatible with the small value of the observed cosmological constant, and the breaking of matter-antimatter symmetry at high energies offering insights into why there is an imbalance between the two in the early universe. In the cosmological modeling of the theory, there exists a proposal to account for the formation of supermassive black holes that are accompanied by their own surrounding galaxies, without relying on the process of mass accretion. The model, in accordance with recent observations conducted by the James Webb Space Telescope, supports the notion that galactic configurations were established relatively early in the history of the universe, shortly after the occurrence of the Big Bang.

Laboratory experiments and investigations into natural phenomena in this research series have unveiled the presence of a gravitational repulsion force that permeates our environment on both microscopic and macroscopic scales, contingent upon the thermal energy present. This paper presents a study exploring novel properties of gravitational forces among gas molecules, employing principles of thermodynamics. A model has been devised based on the interactions between pairs of gas molecules. While traditional models treat gravitational interaction as a singular force, our experimental approach validates it as the composite of two distinct forces: gravitational repulsion and attraction. By utilizing established experimental data on gas thermodynamics, our model demonstrates robust performance both analytically and experimentally. It verifies the coexistence of gravitational repulsion and attraction forces among gas molecules, showcases their Inverse-Cube relationship with distance, and elucidates the direct proportionality of the repulsion force to absolute temperature. This bridges a crucial gap between energy and fundamental forces. The order of magnitudes of gravitational repulsion and attraction forces are found to be considerably large, contrasting with the low values predicted by classical theory, which results from their amalgamation. Recognizing these forces as substantial in magnitude promises unprecedented outcomes and advancements.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Motivated by diffraction experiments on the $\left(2\sqrt{3}\times \sqrt{3}\right)\mathrm{R}{30}^{\circ }$ reconstructed Si(111) due to deposition of rare earth elements (Dy, Tb) and silicide formation we analyse the splitting and non-splitting of superstructure spots. For this purpose, we model diffraction patterns for one dimensional structures generated by the binary surface technique and use supercell models to keep the analysis simple. Diffraction pattern are calculated in the framework of the kinematical diffraction theory and they are analyzed as a function of the domains and domain boundaries. Basic properties of the diffraction pattern are analyzed for model systems of a two-fold and a three-fold periodicity. The rules derived from these calculations are applied to the "real-world" system of Si(111)-($\left(2\sqrt{3}\times \sqrt{3}\right)\mathrm{R}{30}^{\circ }$)-RESi$2_{}$ (RE = Dy or Tb). Depending on the combination of domains and domain boundaries of different types a plethora of different features are observed in the diffraction patterns. These are analyzed to determine the sizes of both domain boundaries and domains from experimentally observed splitting of specific superstructure spots.

Marine renewable energy is emerging as one of the fast-growing industry in the last decades, as modern society pushes for technologies that can convert energy contained from winds, waves, tides and stream flows. The implementation of renewable energy technologies impose high demands on both structural and environmental engineering, as the energy converters have to work under extreme conditions where parameters such as sea-bottom configuration, water transparency and depth, sea-states and prevailing winds are harsh. Constant monitoring of the marine environment is crucial in order to keep this sector reliable. Active acoustics is becoming a standard tool to collect multi-dimensional data from physical, geological and biological properties of the marine environment. The Div. of Electricity of Uppsala University have been developing an environmental monitoring platform based on sonar (Sound Navigation And Raging) systems. This platform aims to monitor the installation, operation and decommissioning of marine renewable energy converters. The focus will be given the observations of behaviours of marine animals in vicinity of energy converters but also structural inspection and monitoring of MRETs. This paper describes how this multifunctional environmental monitoring platform come to existence from the design to the deployment phase.

When dealing with limited sample sizes or missing values in time series data, achieving high accuracy in forecasting becomes challenging. This challenge is particularly common in wind energy forecasting, where many wind farms lack complete data. In this paper, we employ the widely-used ARIMA (Autoregressive Integrated Moving Average) model for time series forecasting. To address the difficulties posed by limited sample sizes and missing values, we adopt a unique approach by utilizing multiple ARIMA models for different datasets. A key distinction from other multiple models methods for time series forecasting lies in each model within our approach using its own dataset, making the fusion process more intricate. To overcome this, we incorporate neural networks and two techniques for model fusion: direct fusion with a learning mechanism and compensation for missing data through training. For each ARIMA model, we introduce a noise estimation method to circumvent the white noise assumptions inherent in ARIMA models. Finally, we apply these methods to wind energy prediction, and our experimental results showcase a significant enhancement in forecasting accuracy.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

Enhancing energy efficiency within the building sector is imperative to curbing energy losses, given that this sector alone contributes to over 34% of global energy consumption. Employing a building management system, along with its regular updates, presents a strategic avenue to decrease energy usage, enhance building energy efficiency, and more. Tailored control strategies, aligned with the unique characteristics and usage patterns of each building, are essential for achieving energy savings. This article presents an evaluation of HVAC system efficiency in office buildings, utilizing a data-driven approach coupled with simulations conducted in IDA ICE software. The research explores the control strategy of an office building equipped with a constant air volume HVAC system, featuring a regularly controlled air handling unit. The objective is to boost energy efficiency while striking a balance between occupant comfort and energy consumption. Findings indicate that by analyzing measured data and adjusting configurable parameters, building energy consumption can be significantly reduced. Close monitoring of indoor parameters by building operators and corresponding adjustments to the HVAC system can yield energy savings of up to 16%. Leveraging these insights, the paper suggests integrating data-driven and dynamic simulation methods into building management system models to optimize HVAC systems, enhance energy efficiency, and advance ambitious carbon neutrality objectives.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

Three-dimensional quantized space model is newly introduced. Quantum mechanics and relativity theory are explained in terms of the warped three-dimensional quantized spaces with the quantum time width (Dt=t_q). The energy is newly defined as the 4-dimensional space-time volume of E = cDtDV in the present work. It is shown that the wave function of the quantum mechanics is closely related to the warped quantized space shape with the space time-volume. The quantum entanglement and quantum wave function collapse are explained additionally. The special relativity theory is separated into the energy transition associated with the space-time shape transition of the matter and the momentum transition associated with the space-time location transition. Then, the quantum mechanics and the general relativity theory are about the 4-dimensional space-time volume and the 4-dimensional space-time distance, respectively.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.