We used light, electron microscope and teased fiber autoradiography to show that myelinating Schwann cells synthesize phospholipids and proteins in perinuclear cytoplasm and superficial cytoplasmic channels or Cajal bands (SCC/CB). Neither phospholipid nor protein syntheses occur in paranodal loops, Schmidt-Lanterman incisures or adaxonal cytoplasm. Autoradiographic studies also show that in support of local protein synthesis, RNAs move from the nucleus into perinuclear cytoplasm and out along SCC/CB. Unlike other phospholipids, phosphatidylinositol synthesis occurs extensively in axons. This finding indicates differences in the distributions of phospholipid synthesizing enzymes in smooth endoplasmic reticulum of Schwann cell processes and axoplasm.Autoradiographs of nerves at longer survival times show that tritiated phosphatidylcholine and fucose-labeled glycoproteins move from synthetic sites to outermost myelin lamellae. From there, phosphatidylcholine spreads inward reaching innermost lamellae of thicker sheaths in days. Coupled with retention of fucose glycoproteins in outer myelin lamellae is the presence of fucose glycoprotein synthesized during early myelination in inner lamellae of thicker sheaths, a result consistent with growth of myelin sheaths from inner lamellae out. In this review, we revisit these studies because they provide temporal and spatial perspectives needed in understanding dynamic aspects of myelinogenesis and how myelinating cells respond to injury and from altered gene expression.

In this work, an analog front-end (AFE) circuit for Electrocardiogram (ECG) detection system has been designed, implemented, and investigated in an industry-standard Cadence simulation framework using advanced technology node of 45 nm. The AFE consists of an instrumentation amplifier, a Butterworth band-pass filter (with fifth-order low-pass and second-order high-pass sections), and a second-order notch filter- all are based on two-stage, Miller-compensated operational transconductance amplifiers (OTA). The OTAs have been designed employing the $g_m/I_D$ methodology. Both the pre-layout and post-layout simulation were carried out. The layout consumes an area of 0.0058 mm$^2$ without the resistors and capacitors. Analysis of various simulation results were carried out for the proposed AFE. The circuit demonstrates a post-layout bandwidth of 239 Hz with a variable gain between 44 to 58 dB, a notch depth of -56.4 dB at 50.1 Hz, a total harmonic distortion (THD) of -59.65 dB (less than 1\%), an input referred noise spectral density of $

Reducing the carbon footprint of energy production is one of the most pressing challenges facing humanity today. Lignocellulosic biomass residues from fruit production industries show promise as a viable energy source. This paper presents a study of the Italian context concerning the utilization of orchard lignocellulosic residues for energy production as electricity or bioethanol. The potential of various orchard residues was assessed through chemical and physical analysis, and an equivalent electrical energy of about 6441.62 GWh or an amount of 0.48 Mt/y of bioethanol was obtained based on the average annual dry residue mass availability of about 3.04 Mt/y. These data represent the 9.30% of the national electrical energy production from renewable sources, as well as the 6.21% of the Italian demand for gasoline in 2022. Electricity generation from these residues shown its potential as a reliable and sustainable baseload power source, as well as source of renewable transportation fuel. The studied process could be a valuable reference to expand these concepts on global scale to achieve a greener and more sustainable energy future.

Methionine oxidation to the sulfoxide form (MSox) is a poorly understood post-translational modification of proteins associated with nonspecific chemical oxidation from reactive oxygen species (ROS) whose chemistries are linked to various disease pathologies including neurodegeneration. Emerging evidence shows MSox site occupancy is in some cases under enzymatic regulatory control mediating cellular signaling including phosphorylation and/or calcium signaling, raising questions as to the speciation and functional nature of MSox across the proteome. The 5XFAD lineage of the C57BL/6 mouse has well-defined Alzheimer’s and aging states. Using this model, we analyzed age, sex and disease dependent MSox speciation in mouse hippocampus. In addition, we explore chemical stability and statistical variance of oxidized peptide signals to understand needed power for MSox based proteome studies. Our results identify mitochondrial and glycolytic pathway targets with increases in MSox with age as well as neuroinflammatory targets accumulating MSox with AD in proteome studies of mouse hippocampus. Further, the paper establishes a foundation for reproducible and rigorous experimental MSox-omics appropriate for biological discovery novel target identification, and biomarker analysis in ROS and other oxidation linked diseases.

In this study, the NiCrAlY coating was prepared using the atmospheric plasma spraying (APS). The sample was then exposed to a continuous fiber laser beam. Laser surface melting (LSM) can effectively homogenize the composition of the coating. It also reduced the defects and roughness. The coating was examined using optical microscopy (OM), scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis. The process parameters of the LSM consist of laser power and scan rate. The high-temperature oxidation test was conducted for 200 hours at a temperature of 1100 °C. After a period of 200 hours, the primary coating demonstrated the emergence of an aluminum oxide layer, along with the presence of harmful spinel oxides. The laser remelting technique was used to modify the surface, which led to the uniform growth and development of an aluminum oxide layer (α-Al₂O₃) during the oxidation examination. Therefore, it appears that the reduction in grain size caused by laser remelting prevents the wrinkling of Al2O3 oxide. This process represents a novel and alternative approach to modifying MCrAlY coatings.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

The influence of the secondary process of evaporation of the reaction product on the kinetics of interaction of gases (O₂, Cl₂, NH₃, H₂O and N₂H₄ vapors) with the surface of some metals (Cr, Pb, Si, Ge) and compounds (BN, SiO₂, SiC) is discussed. Also is considered the case when the growth of the scale is preceded by the process of gas etching of the metal surface. A general equation is given that describes the scale growth-evaporation kinetic (sample mass change - time) curves during the interaction of gases with the surface of metals and compounds. Special cases of parabolic, cubic and fourth degree processes are discussed.

Titanium alloys belong to the metal biomaterials that are one of the most widely used in medicine. In recent years, in order to reduce the use of vanadium, Ti6Al4V alloy is increasingly replaced by Ti6Al7Nb alloy. In addition, to ensure the best possible biocompatibility, its surface is subjected to appropriate modifications, for example, anodic oxidation. Despite the extensive use of anodic oxidation of titanium implants in orthopedics, there are few works focused on a detailed analysis of the chemical composition of the surface layers. In addition, the effect of treatments before anodic oxidation on the properties of the produced layer has not been analyzed. Thus, the purpose of this study was to analyze in detail the chemical composition of the passive layer of Ti6Al7Nb alloy obtained by anodic oxidation preceded by sandblasting. Moreover, the physicochemical properties of the analyzed surface affecting biocompatibility were determined. For this purpose, surface observation, wettability and roughness tests, microhardness tests, electrochemical tests and phase composition analysis were carried out. In addition, the preclinical suitability, of the surface modified in this way, was evaluated by cytotoxicity tests.

.Various synthetic nematicides are currently used effectively in the control of plant parasitic nematodes. However, these nematicides have adverse effects on humans and the environment. Neem oil is eco-friendly alternatives to synthetic nematicides. The effectiveness of repeated neem oil application in suppressing the root-knot nematodes infestation in figs seedlings was therefore examined in this study, both in its natural form (10 ml/L) and in its nano-emulsion form (5 and 7 ml/L). The recorded reduction parameters of M. incognita were J2/250g soil, galls and egg masses / 5g roots of infected fig seedlings were measured at that time, and the effects of these natural additives were compared with the Fosthiazate (Krenkel 75%EC). The impact of such soil amendments on some typical plant parameters, the total microbial count of soil, and the overall enzymatic activity of the fig rhizosphere were also included. Obtained results revealed that the soil population density of root knot nematode suppressed by 80.3% , reduction of nematode egg masses (60.4%) due to the application of nano-emulsion of neem oil (at 7ml/L). Present work recommend the use of nano-emulsion of neem oil as one of the effective and eco-friendly means to reduce the root- knot nematode on fig .

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

Chronic kidney disease (CKD) is characterized by a continuous decline in kidney function, often persisting for years or even a lifetime. This study presents a new exploration into the extraction and application of insect chitosan (Tenebrio molitor) targeting hemodialysis (HD). Initially, the potential of insect-derived chitosan as a sustainable and effective alternative to traditional sources (i.e. crustaceans) is demonstrated. Efficient extraction methods were developed (totaling between 6 h and 12 h), producing chitosan. Firstly, chitin was efficiently isolated from T. molitor through deproteinization and demineralization, with yields of approximately 5% (w/w). Subsequently, chitosan was obtained from the extracted chitin resulting in yields of between 65.0 ± 0.8% (w/w) and 79.3 ± 0.8% (w/w). Characterization using Fourier Transform Infrared Spectroscopy (FTIR) confirmed structural similarities with commercial chitosan and degrees of deacetylation in the 73 - 75% range. The bioactive properties of chitosan obtained from T. molitor, including antimicrobial and antioxidant activities, were evaluated. All the microorganisms tested were inhibited, exhibiting minimum lethal concentrations between 2 and 8 mg/mL, confirming the antimicrobial activity of the extracted chitosan. In addition, chitosan showed antioxidant activity in the range of 60 to 65 µmol Trolox equivalent/g, suggesting its viability for various medical applications.This study also developed a chitosan-based membrane (CH - M) culminating in a proof-of-concept phase for hemodialysis. The permeation characteristics of CH-M for urea and albumin were studied in vitro to assess their suitability as HD membranes. Urea was permeable to values of over 70% and albumin was retained.

Salmonella infections can lead to intestinal inflammation and metabolic disorders in birds. However, whether ARA metabolism is involved in Salmonella-induced intestinal inflammation remains unclear. This experiment investigated the changes in cecal flora and arachidonic acid (ARA) metabolism in Hainan Wenchang chickens infected with S. Typhimurium using 16s rDNA sequencing and targeted metabolomics. The results showed that the levels of ARA metabolites were increased in the cecum tissue of Wenchang chickens after infection with S. Typhimurium, including prostaglandin E2, prostaglandin F2α, lipoxin A4, ±8(9)-EET, ±11(12)-EET, and ±8,9-DiHETrE. The content of key enzymes for ARA production and metabolism (PLA2 and COX-2) in chicken cecum tissues was increased after S. Typhimurium infection. The relative mRNA levels of inflammatory factors were also increased after infection, including IFN-γ, TGF-β1, IL-4, and IL-6. In HD11 cells, the use of a cyclooxygenase (COX) inhibitor reduced the increased levels of COX-2 and PGF2α induced by S. Typhimurium infection and effectively reduced the inflammatory response. In addition, the number of beneficial genera (e.g., Bifidobacterium, Lactobacillus, and Odorobacterium) in the cecum of Wenchang chickens was significantly reduced after infection with S. Typhimurium. In this study, we revealed the structure of the cecal flora of Wenchang chickens infected with S. Typhimurium and demonstrated that S. Typhimurium can mediate the onset and development of intestinal inflammation through the activation of the metabolic pathway of ARA cyclooxygenase in Wenchang chickens. The results can provide data support and theoretical support for the prevention and control of avian salmonellosis.

Molluscs are significant species in aquatic ecology. Molluscs are crucial for maintaining ecological balance as secondary consumers and serving as bioindicator species in biomonitoring systems. Molluscs are threatened by pesticides such as commonly used pyrethroid insecticides. Pyrethroids are typical insecticides used to control insects in agriculture and gardening. Pyrethroids are increasingly being utilized in both agricultural and human activities. Pyrethroids enter aquatic bodies through rainfall and drainage systems. The use of pyrethroids is becoming a significant concern for aquatic creatures, particularly molluscs. The discussion will focus on the increasing issue of pyrethroids becoming a nightmare for molluscs. Pyrethroids, due to their lipophilic nature, pose a significant risk to molluscs by affecting their metabolites, producing reactive oxygen species, and influencing neurotransmitter actions. Molluscs are crucial organisms in aquatic ecosystems, and their threats warrant significant discussion and attention. This review will delve into the behaviour of pyrethroids on molluscs.

The study assessed the trapping efficacy of locally-modified 1) Gravid Aedes Trap(GAT) lined with insecticide-treated net (ITN) as a killing agent, 2) Autocidal Gravid Ovitrap(AGO) with sticky board in the semi-field system (SFS) and field setting. Fully-balanced Latin square experiments were conducted to compare GAT lined with ITN vs AGO, both with either yeast or grass infusion. Biogents-Sentinel (BGS) with BG-Lure and no CO2 was used as standard trap for Aedes mosquitoes. In the SFS, GAT outperformed AGO in collecting both nulliparous (65% vs 49%,OR=2.22,[95%CI:1.89-2.60],p

The pervasive presence of atmospheric pollution, particularly polycyclic aromatic hydrocarbons such as 7,12-dimethylbenz(a)anthracene, instigates aberrant cellular and tissue conditions, precipitating oxidative damage and inflammatory cascades conducive to the onset of cancer, notably mammary cancer. Given the hepatic metabolism of 7,12-dimethylbenz(a)anthracene, the imperative of employing natural antioxidants becomes apparent. In this study, we delve into the antioxidant and hepato-protective properties of Pistacia lentiscus against 7,12-dimethylbenz(a)anthracene-induced toxicity, alongside exploring its potential anticancer attributes. Our investigations unveil Pistacia lentiscus's anti-proliferative efficacy against human breast cancer cell lines. Notably, 7,12-dimethylbenz(a)anthracene-intoxication escalates body weight, disrupts lipid profiles, and incites serum oxidative damage. Concurrently, hepatic and renal oxidative stress ensue, accompanied by heightened antioxidant enzyme activity in the 7,12-dimethylbenz(a)anthracene-exposed-group compared to controls (p<0.05). Nonetheless, Pistacia lentiscus co-administration rectifies biochemical imbalances, significantly attenuates oxidative stress aberrations, and augments antioxidant enzyme responses (p<0.05). Importantly, histological analysis evinces Pistacia lentiscus's shielding effect against 7,12-dimethylbenz(a)anthracene induced hepatocyte injury and steatosis. Our findings underscore Pistacia lentiscus's robust anti-proliferative, antioxidant, and hepato-protective capacities, mitigating metabolic disturbances, oxidative stress propagation in liver and kidney functions, and potential histological alterations, thereby impeding 7,12-dimethylbenz(a)anthracene-induced mammary cancer initiation. We posit that Pistacia lentiscus may serve as a prophylactic agent against breast cancer instigated by this carcinogen.

This paper explores if plants are capable of responding to human movement by changes in their electrical signals. Towards that goal we conducted a series of experiments, where humans over a period of 6 months were performing different types of eurythmic gestures in proximity of garden plants, namely salad, basil, and tomatoes. To measure plant perception, we used the plant spikerbox, a device that measures changes in voltage differentials of plants between roots and leaves. Using machine learning, we find that the voltage differentials over time of the plant predict if (a) eurythmy has been performed, and (b) which kind of eurythmy gestures has been performed. We also find that the signals are different based on the species of the plant. In other words, the perception of a salad, tomato, or basil might differ just as perception of different species of animals differ. This opens new ways of studying plant ecosystems, while also paving the way to use plants as biosensors for analyzing human movement.

Ethical considerations regarding our treatment of animals have gained strength, leading to legislation and a societal focus across various disciplines. This is a subject of study within curricula related to agri-food sciences. The aim was to determine the perceptions of agronomy university students concerning animal welfare in livestock production systems. A survey was conducted to encompass various aspects, from participants' sociodemographic attributes to their attitudes and behaviors regarding animal welfare and the consumption of animal products. Statistical analysis, performed using R software, delved into the associations between participants' characteristics and their perspectives on the ethical, bioethical, and legal dimensions of animal welfare. Associations between demographic factors and ethical viewpoints among students were identified. Gender differences emerged in animal treatment perceptions, while rural and urban environments impacted perspectives on various animals. Bioethical considerations revealed distinctive disparities based on gender and education in concerns for animal welfare, value perceptions, evaluations of animal behaviors, and opinions on animal research. It is crucial to distinguish between animal welfare and ethical considerations arising from coexisting with sentient beings capable of experiencing suffering. Ethical theories provide a lens through which we perceive our obligations toward animals. The responsibility to ensure animal welfare is firmly rooted in recognizing that animals, like humans, experience pain and physical suffering. Consequently, actions causing unjustified suffering or mistreatment, particularly for entertainment purposes, are considered morally unacceptable.

This work aims to investigate the effect of process temperature and catalyst content by thermochemical degradation of municipal solid waste (MSW) fraction (organic matter + paper + plastic) on the yield of reaction products (bio-oil, biochar, H2O and gas), physicochemical properties and chemical composition of bio-oils, as well as on the morphology and crystalline phases of biochar in laboratory scale. The organic matter, paper and plastic segregated from the gravimetric composition of total waste sample were subjected to the pre-treatments of drying, crushing and sieving. The experiments were carried out at 400, 450 and 475 °C and 1.0 atmosphere, and at 450 °C and 1.0 at-mosphere, using 5.0, 10.0 and 15.0% (wt.) of FCC zeolite, bath mode, using a laborato-ry scale glass reactor. The bio-oil was characterized for acidic value. The chemical functions present in the bio-oil identified by FT-IR and the composition by GC-MS. Biochar was characterized by SEM/EDS and XRD. Thermal pyrolysis of the MSW frac-tion (organic matter + paper + plastic) shows bio-oil yields between 9.44 and 9.24% (wt.), aqueous phase yields between 21.93 and 18.78% (wt.), solid phase yields between 67.97 and 40.34% (wt.) and gas yields between 28.27 and 5.92% (wt.). The yield of bio-oil decreases with increasing process temperature. For the experiments using FCC, the biochar and gas yields increase slightly with the FCC content, while that of bio-oil de-creases and the H2O phase remains constant. The GC-MS of bio-oils identified the presence of hydrocarbons and oxygenates, as well as nitrogen-containing compounds, including amides and amines. The acidity of the bio-oil increased with increasing temperature and with the aid of FCC as a catalyst. It has been identified the presence of hydrocarbons within bio-oil by addition of FCC catalyst due to the deoxygenation of carboxylic acids, followed by decarboxylation and decarbonylation reactions, producing aliphatic and aromatic hy-drocarbons.

Diabetes mellitus (DM) is a metabolic disorder characterized by the deficiency of insulin production and is one of the concerning health problems worldwide, especially in developing countries. Considering the systemic toxicity associated with current antidiabetic medications and their limited efficacy, there is an urgent need to discover new plant-based natural antidiabetics. Since time immemorial, medicinal plants have played an important role in the management of health disorders. In recent years, herbal medicine has experienced exponential growth in popularity worldwide, owing to its natural origin and fewer side effects, appealing to both developing and developed nations. Ecuador has a rich cultural history in ethnobotany that plays a crucial role in their people's lives. Several Ecuadorian medicinal plants have hypoglycemic or an-ti-hyperglycemic properties that are rich with bioactive phytochemicals. These medicinal plants were extensively used in traditional medicine preparation in Ecuador for many decades to treat diabetes because of their cost-effectiveness, available traditional knowledge, and low toxicity. Many Ecuadorian medicinal plants are reported to have antidiabetic properties that reduce blood sugar levels, and oxidative stress, regulate intestinal function, improve insulin resistance, inhibit α-amylase and α-glucosidase, lower gluconeogenic enzymes, stimulate glucose uptake mechanisms, and play an important role in glucose and lipid metabolism, yet there is a substantial lack of integrated approach between the existing ethnomedicinal practice and pharmacological research. Therefore, this review aims to discuss and explore the traditional medicinal plants used in Ecuador for treating DM and their bioactive phytochemicals, which are mainly responsible for their anti-diabetic properties.

Copper(II), nickel(II) and zinc(II) complexes of various peptide fragments of tau protein were studied by potentiometric and spectroscopic techniques. All peptides contained one histidyl residue and represented the sequences of tau(91-97) (Ac-AQPHTEI-NH2), tau(385-390) (Ac-KTDHGA-NH2) and tau(404-409) (Ac-SPRHLS-NH2). Imidazole-N donors of histidine were the primary metal binding sites for all peptides and all metal ions but in case of copper(II) and nickel(II) the deprotonated amide groups were also involved in metal binding by increasing pH. The most stable complexes were formed with copper(II) ion but the presence of prolyl residues resulted in significant changes in the thermodynamic stability and speciation of the systems. It was also demonstrated that nickel(II) and especially zinc(II) complexes have relative low thermodynamic stability with these peptides. Copper(II) catalyzed oxidation of the peptides was also studied. In the presence of H2O2 the fragmentation of peptides can be detected in all cases. In the simultaneous presence of of H2O2 and ascorbic acid the extent of the fragmentation of the peptide is less preferred, and the formation of 2-oxo-histidine also occurs.

Hansenula polymorpha is a non-conventional, methylotrophic, and thermo-tolerant yeast well known for the industrial production of recombinant proteins. However, the research to evaluate this yeast potential for sugar fermentation to produce alcohols for biofuel applications is at an infant stage. For research advancement, the present work investigated the wild type H. polymorpha strain (DSM 70277) for the co-production of methanol, ethanol, and butanol using a batch fermentation reactor and performing experiments at an ideal temperature of 40°C with a pH of 5.5 using different sugars (fructose, glucose, and xylose) as substrates. The maximum specific growth rates (h-1) of H. polymorpha yeast were 0.59–3.02 for fructose, 0.08–2.60 for glucose, and 0.06–0.08 for xylose. The overall yields (g/g) of methanol were higher from fructose (0.132–0.226) than glucose (0.020–0.021) and xylose (0.009–0.030). Ethanol overall yield (g/g) from fructose (0.130–0.325) was more than glucose (0.054–0.167), and xylose (0.042–0.068). The overall butanol yield (g/g) ranged from 0.018–0.031 (fructose), 0.017 (glucose), and 0.009–0.010 (xylose). Due to the methylotrophic nature of H. polymorpha, a shorter time (preferably 2 h) was found suitable for co-production of methanol, ethanol, and butanol.

Driven by environmental sustainability concerns, the integration of biobased components in curtain wall systems is gaining traction in both research and the construction market. This paper explores the development and validation of a bio-based façade system within the Basajaun H2020 project. The project aimed to demonstrate the feasibility of introducing environmentally friendly bio-based components into the mature curtain wall façade industry. The paper focuses on identifying technological solutions for replacing key components such as profiles, insulation, and the tightness system with bio-based and less environmental impact alternatives presenting the results achieved in the façade system design of the Basajaun project funded by European Union. These solutions aimed at creating a bio-composite-based curtain wall façade that adheres to current building envelope standards and normative; to implement diverse façade typologies for vision panels, opaque sections, and integrated windows; to engineer the prefabrication process for industrialization, enabling wider market replication and simplified transport and installation. The results demonstrate that the Basajaun façade successfully integrates selected components and meets the performance requirements set by regulations. However, questions remain regarding the workability of bio-based profiles as a commercially viable, ready-to-market solution that can replace traditional aluminum profiles in the curtain wall façade industry.

In the construction sector, the integration of biobased materials has emerged as a pivotal aspect of EU policies, aimed at promoting sustainable practices throughout the value chain to mitigate resource consumption and carbon emissions. This paper explores the development and validation activities of a bio-based façade system within the Basajaun H2020 project, focusing on enhancing the utilization of biobased components within building envelopes to replace conventional solutions with eco-friendly alternatives. This paper reports the methodologies employed to detect requirements and outline the testing protocols undertaken to validate the façade system design devised within the project focusing on the original façade components as the bio composite profile. Vision and opaque façade modules are prototyped and tested following curtain wall standards standard for performance and acoustic assessments, to showcase the efficacy of the developed solution. The conducted tests demonstrate the feasibility of integrating bio-based components into building envelopes, aligning with project expectations, and prevailing standards for curtain wall façade solutions. Notably, the designed façade system meets technical conditions and project objectives. Nevertheless, the research underscores the need for further refinements to facilitate solution industrialization and explore broader market applicability. Future efforts will focus on addressing these improvements and assessing the scalability of the solution.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

Obesity results in hepatic fat accumulation, i.e., steatosis. Besides the fat overload, impaired fatty acid β-oxidation also promotes steatosis. Fatty acid β-oxidation takes place in mitochondria and peroxisomes. Usually very long chain and branched-chain fatty acids are first oxidized in peroxisomes, and the resultant short chain fatty acids are further oxidized in mitochondria. Peroxisome biogenesis is regulated by peroxin 16 (PEX16). In liver-specific PEX16 knockout (Pex16Alb-Cre) mice, hepatocyte peroxisomes were absent, but hepatocytes proliferated, and liver mass was enlarged. These results suggest that normal liver peroxisomes restrain hepatocyte proliferation and liver sizes. After high fat diet (HFD) feeding, body weights were increased in PEX16 floxed (Pex16fl/fl) mice and adipose-specific PEX16 knockout (Pex16AdipoQ-Cre) mice but not in the Pex16Alb-Cre mice, suggesting that the development of obesity is regulated by liver PEX16 but not by adipose PEX16. However, it was previously reported that HFD-induced obesity in the Pex16AdipoQ-Cre mice was more severe than in the wild type mice, which was not observed until 27 weeks of HFD feeding. Thus, liver initiates the development of obesity, which is enhanced by abnormal adipocytes. HFD increased liver mass in the Pex16fl/fl mice but somehow reduced the already enlarged liver mass in the Pex16Alb-Cre mice. Basal levels of serum triglyceride, free fatty acids and cholesterol were decreased whereas serum bile acids were increased in the Pex16Alb-Cre mice, and HFD-induced steatosis was not observed in the Pex16Alb-Cre mice. These results suggest that normal liver peroxisomes contribute to the development of liver steatosis and obesity.

Poly(vinyl acetate) (PVAC) is a ubiquitous polymer in various industrial applications, including paints and adhesives. While extensive research has focused on understanding the degradation mechanisms of PVAC-based paint, under different environmental conditions, limited attention has been paid to the long-term stability of PVAC-based white glues, especially when used in artworks. This study investigates the accelerated degradation of a commercial PVAC-based white glue considered as representive of this class of materials as used in contemporary artworks, to predict its durability and assess its behavior in art objects. Through accelerated aging experiments and comparison with natural aging observed in artworks, the study reveals the formation of chromophores and the release of plasticizer as key degradation processes. Despite minimal structural modifications in PVAC, the loss of plasticizer leads to an increase in glass transition temperature, affecting the adhesive's cohesive strength and contributing to detachment of materials in artworks. The findings underscore the importance of preventive conservation measures to mitigate degradation issues in PVAC-based artworks.

The aim of this study was to assess the influence of thermocompression conditions on lignocellulosic biomass such as sugarcane bagasse (SCB) in the production of 100% binderless bio-based materials. Five parameters were investigated: pressure applied (7-102 MPa), molding temperature (60-240°C), molding time (5-30 min), fiber/fine particle ratio (0/100-100/0) and moisture content (0-20%). These parameters affected the properties and chemical composition of the materials. The density ranged from 1198 to 1507 kg/m3, the flexural modulus from 0.9 to 6.9 GPa and the flexural strength at breaking point from 6.1 to 43.6 MPa. Water absorption (WA) and thickness swelling (TS) respectively ranged from 21% to 240% and from 9% to 208%. Higher mechanical properties were obtained using SCB with fine particles, low moisture content (4-10%), high temperature (≥ 200°C) and pressure (≥ 68 MPa), while water resistance was improved using more severe thermocompression conditions with the highest temperature (240°C) and time (30 min) or a higher moisture content (≥ 12.5%). Correlations were noted between the mechanical properties and density, while the material obtained with only fine particles had the highest mechanical properties and density. Material obtained with a 30 min molding time had the lowest WA and TS due to internal chemical reorganization followed by hemicellulose hydrolysis into water-soluble extractables.

Bio-absorbable stents are a novel tool which relieve stenosis and then resorb as the patient grows, avoiding obligatory re-intervention. This case describes the novel use of an iron bio-absorbable stent in a child with surgically repaired Tetralogy of Fallot who post-operatively developed a severely stenotic right ventricular outflow tract.

This article introduces a novel nature-inspired metaheuristic algorithm called Frilled Lizard Optimization (FLO), which emulates the hunting behavior of frilled lizards in their natural habitat. FLO draws in-spiration from the sit-and-wait strategy observed in frilled lizards during hunting. The underlying theory of FLO is presented and mathematically formulated in two phases: (i) an exploration phase, simulating the frilled lizard's attack towards prey, and (ii) an exploitation phase, simulating the lizard's retreat to the top of the tree after feeding. To assess FLO's efficacy in solving optimization problems, the algorithm's performance is evaluated across fifty-two standard benchmark functions, encompassing unimodal, high-dimensional multimodal, fixed-dimensional multimodal, and the CEC 2017 test suite. Comparative analyses with twelve existing metaheuristic algorithms are conducted. The simulation results reveal that FLO, distinguished by its adeptness in exploration, exploitation, and balancing them during search process, outperforms competing algorithms. Additionally, FLO is implemented on twenty-two constrained optimization problems from the CEC 2011 test suite and four engineering design problems, demonstrating its effectiveness in addressing real-world optimization applications.

The well-being and sociability of individuals have always been part of modernity. The development of new technologies that meet these aspirations is receiving increasing attention. Thus, strengthening the desired objectives of these tools and minimizing their undesirable side effects is the subject of a growing commitment. The present contribution aims, in this context, to evaluate and analyze the desired and undesirable effects of the interaction of electromagnetic fields with living tissues in general. This involves routines reinforcing expected functions as well as those controlling and protecting against undesirable effects. First, the interactions of electromagnetic fields with tissues are analyzed, involving their thermal biological effects of desired and undesired exposures. The roles of blood and sap fluids in bio-affected tissues are then analyzed. Secondly, the governing electromagnetic, bio-heat equations, and their coupled solution are studied. Third, the thermal behavior of tissues and the exposure adverse effects are examined. Next, monitoring and defending of the effects of exposures are discussed. This contribution illustrates and discusses mathematical modeling routines based on a generalized interaction of electromagnetic fields with living tissues.

Abstract Cholesterol has ruled the history of atherosclerotic cardiovascular diseases (CVD) for decades, and the transport of cholesterol by lipoproteins has become a cornerstone of our view of etiology of the disease. Discovery of the lipoprotein-specific transport of lipid oxidation products (LOP) has opened a new and exciting area in research of CVD by revealing strong connections between atherogenic LOP, lipoprotein transport functions and CVD. This review goes through the evidence in support of the lipoprotein-specific LOP transport and speculates of possible consequences of the proposed role of lipoprotein LOP transport as a risk factor. Association of lipoprotein LOP with known risk factors of CVD are largely parallel with those of cholesterol, and due to the common transport and cellular intake mechanisms the elucidation of independent effects of either cholesterol or LOP is difficult. Yet, unlike cholesterol, LOP can directly initiate and boost atherogenic processes. It therefore appears inevitable that increasing knowledge of the lipoprotein-specific LOP transport will affect the present view of the role of cholesterol in aetiology and as a risk factor of CVD.

Plastic waste accumulation poses significant environmental challenges, underscoring the importance of closing the plastic life cycle by converting waste into valuable products. Pyrolytic char, a promising byproduct, offers diverse industrial applications. However, little attention has been given to converting hydrocarbon-based plastics into solid carbon due to their low fixed carbon content. This study compares sulfonation and thermal oxidation stabilization techniques for carbonizing waste polyethylene and polyvinyl chloride. Results indicate sulfonation yields higher pyrolytic char formation and improves surface properties, surpassing Al2O3 in catalyst support characteristics. Thermal oxidation increases fixed carbon content but adversely affects char yield and surface properties. Both methods effectively enhance fixed carbon content, but sulfonation emerges as more advantageous, suggesting potential use of plastic-derived char as a catalyst support material, contributing to circular economy development.

The rapid increasing rate of soil and water bodies pollution is the main anthropogenic effect caused by the mismanagement of post-consumer plastics. This research evaluated the effectiveness of cattail (Typha Latifolia) fibers (CFs) as bio-adsorbents of microplastic particles (MPPs) from wastewater. The effect of the adsorption environment composition on the adsorption rate was investigated. Batch tests were conducted to evaluate the “spontaneous” adsorption of MPs onto CFs. Five MPPs materials (PVC, PP, LDPE, HDPE, and Nylon 6) were evaluated. An industrial wastewater (PW) and Type II Distilled Water (DW) were employed as adsorption environments. The batch tests results show that CFs are effective in removing MPPs from DW and PW. However, higher removal percentage of MPPs were obtained in PW, ranging from 89% to 100% for PVC, PP, LDPE, and HDPE; while the adsorption of Nylon 6 increased to 29.9%, a removal increased of 50%. These observations indicate that hydrophobic interactions drive the “spontaneous and instantaneous” adsorption process and that adjusting the adsorption environment effectively enhances the MPPs removal rate. This research demonstrates the important role that bio-substrates can play in reducing the environmental pollution as efficient, sustainable, low cost, and reliable adsorbents for the removal of MPPs from wastewaters.

MgAl oxide coatings containing MgO and MgAl2O4 phases were doped with CeO2 particles using plasma electrolytic oxidation (PEO) of AZ31 magnesium alloy in 5 g/L NaAlO2 water solution, with CeO2 particles added at concentrations up to 8 g/L. They underwent extensive inve-stigation into their morphology, chemical and phase compositions, and most importantly, photoluminescent (PL) properties and photocatalytic-activity (PA) in photodegradation of methyl orange (10 cm3 of 8 mg/L). The concentration of CeO2 particles in the aluminate electrolyte influences the amount of CeO2 particles incorporated into MgAl oxide coatings, but CeO2 particles have no signi-ficant effect on the surface morphology, thickness, or phase structure of the coatings. The PL emi- ssion spectrum of MgAl oxide coating is divided into two bands: one in the 350-600 nm range related to structural defects in MgO, and another much more intense in the 600-775 nm range attributed to F+ centres in MgAl2O4. Incorporated CeO2 particles do not have a significant effect on the PL intensity of the band in the red spectral region, but the PL intensity of the first band increases with the concentration of CeO2 particles. PA of MgAl/CeO2 oxide coatings is higher than that of pure MgAl oxide coatings. The highest PA was observed for MgAl/CeO2 oxide coatings formed in aluminate electrolytes with the addition of 2 g/L of CeO2 particles. The MgAl/CeO2 oxide coatings remained chemically and physically stable across multiple cycles, indicating their potential for applications.

Among cephalopod discards, ink has revealed several beneficial properties regarding human health, environmental preservation and food preservation. In this study, different concentrations of an aqueous extract of cuttlefish (Sepia spp.) ink (CI) were added, respectively, to the packing medium employed during golden seabream (Sparus aurata) canning. Quality parameters of the resulting canned fish were determined and compared to the counterpart control and raw samples. As a result, an important effect of the CI concentration added to the packing medium was proved. The presence in the packing medium of a relatively low CI concentration led to lower (p<0.05) lipid oxidation development (fluorescent compound formation), lower (p<0.05) changes of colour parameters (L* and a* values) and lower (p<0.05) trimethylamine values in canned fish. Additionally, the two lowest CI concentrations tested led to higher average values of C22:6ω3 and ω3/ω6 ratios. Remarkably, higher average values of free fatty acids, polyene index and C20:5ω3 were detected in all kinds of CI-treated fish when compared to control canned samples. In agreement with environmental sustainability and circular economy requirements, the study provides a first approach to a novel and beneficial use of the present marine discard for the quality enhancement of canned fish.

Cardiotoxicity is an unwanted side-effect arising from different medications. The term describes a diminution of heart function, affecting especially left ventricular ejection fraction, which can progress to heart failure. Pediatric oncology patients treated with drugs of the anthracycline group, e.g., doxorubicin, can evolve to heart failure patients in adult age. Nuclear Medicine imaging of fatty acid oxidation and glycolysis accurately describes normal and altered heart metabolism. The most common finding is a state of cardiac glycolysis, which is reflected by increased uptake of 18F-desoxyglucose (18F-FDG) at a time when fatty acid oxidation is decreased. Glycolysis has recently been recognized as being the result of coenzyme Q10 deficiency as part of adaptation to hypoxia. Low LEVF correlates with impaired fatty acid oxidation. This deficiency can arise from chemotherapy and radiation and can be corrected by supplementation. Drugs like enalapril can improve fatty acid utilization. We will review relevant Nuclear Medicine imaging studies as well as fundamental biochemical data that demonstrate this pathogenetic path.

Metal-catalyzed lipid oxidation is a major factor in food waste, as it reduces shelf life. Addressing this issue, our study investigates the potential of hydrolysates derived from potato protein, a by-product of potato starch production, as metal chelating antioxidants. Through sequential enzymatic hydrolysis using Alcalase or Trypsin combined with Flavourzyme, we produced various hydrolysates, which were then fractionated via ultrafiltration. Using a combination of peptidomics and bioinformatics, we predicted the presence of metal-chelating and free radical scavenging peptides across all hydrolysate fractions, with a trend indicating a higher content of antioxidant peptides in lower molecular weight fractions. To validate these predictions, we utilized Surface Plasmon Resonance (SPR) and a 9-day emulsion storage experiment. While SPR demonstrated potential in identifying antioxidant activity, it faced challenges in differentiating between hydrolysate fractions due to significant standard errors. In the storage experiment, all hydrolysates showed lipid oxidation inhibition, though not as effectively as EDTA. Remarkably, one fraction (AF13) was not significantly different (p < 0.05) from EDTA in suppressing hexanal formation. These results highlight SPR and peptidomics/bioinformatics as promising yet limited methods for antioxidant screening. Importantly, this study reveals the potential of potato protein hydrolysates as antioxidants in food products, warranting further research.

Naturally-derived synthetic leather is a widely used and high-quality type of faux leather or synthetic leather. Many consumers prefer authentic leather goods due to their exceptional qualities, including high water vapor permeability and superior wearing comfort. Consequently, the exploration of artificial leather made from natural materials with exceptional qualities as an alternative to genuine leather has garnered significant interest and is now a highly studied subject. Synthetic leather, sometimes known as imitation leather, has gained popularity recently as a highly suitable alternative to genuine leather. Continuous advances in this area of research increase the range of uses for synthetic leather using natural fibers. Thus, this research aims to explore synthetic leather materials using orange peel waste, which can be applied to the fashion industry. This research applies several types of orange peel waste, such as Pomelo, Sweet orange, and Sunkist orange, to different compositions and strengthening materials, such as bandages and dacron. The resulting bio-composite materials' morphology, mechanics, and adhesive properties were evaluated following ASTM D 2209-00 and ASTM D 4533-04 standards. The results indicate that specimen 1A (Pomelo using bandage as reinforcement) has the most significant effects, with a tensile test value of approximately 472 N/cm2, an elongation of roughly 67.28 % was the highest value on sweet orange using bandage as reinforcement, and a tear resistance of around 14.28 N/cm2 for Pomelo with bandage as reinforcement. Furthermore, the test results also show that composition 2B still does not meet the standards of SNI 1294:2009 and ISO 3376 for tensile strength and ISO 3377-1 for tear strength. Additionally, statistical analysis showed no appreciable changes in the samples analyzed. Furthermore, statistical evaluations showed no significant alterations in the studied samples. The results of this experimental investigation can be explored further and used as a basic framework for the creation of bio-composites from orange peel waste for future fashion.

The integration of clean energy generation with wastewater treatment holds promise for addressing both environmental and energy concerns. Focusing on photocatalytic hydrogen production and wastewater treatment, the study introduces PdIn/TiO2 catalysts for the simultaneous removal of the pharmaceutical contaminant paracetamol and hydrogen production. Physicochemical characterization showed a high distribution of Pd and In on the support as well as a high interaction with it. The Pd and In deposition enhances the light absorption capability and significantly improved HER in comparison to TiO2 not only in the electrolyte but also in presence of paracetamol. Regarding PTM oxidation, TiO2 and PdIn/TiO2 showed an irreversible behavior toward the PTM oxidation, limited by the adsorption of species on the electrode surface. Thus, PdIn-doped TiO2 stands out as a promising catalyst, showcasing enhanced physicochemical properties and superior catalytic performance. This underscores its potential for both environmental remediation and sustainable hydrogen production.

The degradation of the persistent compound perfluorooctanoic acid (PFOA) in water by ultraviolet light in the presence and absence of hydrogen peroxide was examined. A laboratory experiment was designed to answer the question: is UV spectrophotometry feasible for PFOA research? Spectrophotometry was able to measure the degradation of PFOA, but a very high concentration was required. The 1 mg/L used is very concentrated when compared to the 70 ng/L suggested level in drinking water. A UV/Visible diode array scanning spectrophotometer was used to measure changes in PFOA concentrations after 15-minute exposures to ultraviolet light and ultraviolet light with hydrogen peroxide. A noticeable drop in concentration was measured for a 1 mg/L sample. The reaction kinetics were calculated and are likely skewed due to the greater concentration of experimental PFOA. These preliminary results will allow for the next phases of PFOA research to commence, including confirmation through liquid chromatography/mass spectrometry of low concentrations and developing bioremediation techniques.

Electronic waste (e-waste), characterized by the widespread disposal of electronic devices, shows a growing environmental challenge. In this study, we explore the electrocatalytic potential of gold nanoparticles supported on Vulcan obtained from e-waste for their application as electrocatalysts for the methanol oxidation reaction in alkaline media. Gold nanoparticles are synthesized from gold coatings recovered from Intel Pentium 4 processor pins, highlighting their sustainability as electrocatalyst precursors. Comprehensive characterization, including UV-Vis spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray dif-fraction, is performed to assess the electrocatalyst's structural properties. Electrochemical evalu-ation is carried out in 0.5 M KOH electrolyte employing the rotating disk electrode technique, us-ing cyclic voltammetry for the study of methanol oxidation. Remarkably, the gold nanoparticles show electrocatalytic activity on par with commercially synthesized counterparts, demonstrating the feasibility of this approach for sustainable electrocatalyst production. Thus, this research opens new routes for utilizing e-waste as a source of valuable catalyst materials, addressing en-vironmental and technological challenges in the field of alkaline fuel cells.

The objective of this study is to evaluate how two varying amounts of sepiolite-based powder, infused with indigo extract, affect the appearance and durability of a water-based white primer. To examine the influence of this eco-friendly pigment on the coatings' overall appearance, assessments were performed for color, gloss, and surface roughness. Additionally, the coatings were investigated through optical and electron microscopic observations, to evaluate the distribution of the pigment within the polymer matrix. The effect of the pigment on the coating's durability was assessed through accelerated tests, including exposure in a salt spray chamber and a UV-B chamber. These tests aimed to evaluate the emergence of defects and changes in the appearance of the samples over time. Furthermore, the impact of different quantities of sepiolite-based powder on the coating's ability to act as a barrier was assessed using liquid resistance tests and contact angle measurements. These evaluations aimed to understand how the coating responded to various liquids and its surface properties concerning repellency or absorption. In essence, this study underscores the considerable influence of the eco-friendly pigment, demonstrating its capacity to introduce unique color and texture variations to the paint. Moreover, the inclusion of the pigment has enhanced the coating's color stability, its ability to act as a barrier, and overall durability when exposed to harsh environments.

We use COMSOL Multiphysics software to model optical processes in media and the effects of light propagation in whispering gallery mode resonators (WGMRs). Although plane wave irradiating on resonator does not create resonances, it was shown that they can be obtained when focused tangentially on the perimeter of the resonator. We demonstrate that resonances can be excited in resonators by prism coupling when the incident angle of the light is larger than the angle of total internal reflection. We determined the optimal distance between the prism and the resonator to get the strongest resonances. Bio-sensing principle of WGMRs is shown by demonstrating that the shift of resonances increases with a larger number of "bio-molecules" attached to the surface of WGMR. Surface functionalization and surface roughness were explored.

Recent development for synthesis of bio-based long chain aliphatic polyesters by acyclic diene metathesis (ADMET) polymerization of α,ω-dienes, derived from plant oils and bio-based chemicals, like bis(10-undecenoate) with isosorbide, using ruthenium-carbene catalysts have been reviewed. Development of subsequent (one-pot) tandem hydrogenation afforded saturated polyesters under mild conditions. The polymerizations under bulk (without solvent, 80-90 ºC) or in ionic liquids (50 ºC) under vacuum conditions enabled synthesis of high molar mass polymers (Mn &gt;30,000 g/mol). The polymerization by molybdenum-alkylidene catalyst afforded the highest molecular weight polyesters (44000‒49400 g/mol, in toluene at 25 ºC) exhibiting promising tensile properties (strength and elongation at break) beyond polyethylene, polypropylene. Depolymerizations of these polyesters including closed loop chemical recycling were also demonstrated. Catalyst developments (more active, under mild conditions) play a key role for the efficient synthesis.

Tungsten and its alloys are considered as a key component in high temperature environment. Self-passivating W-Si-xY alloys with different Y contents made from the powders milled for different times were prepared by mechanical alloying (MA) and spark plasma sintering (SPS). Their microstructures and oxidation resistance were investigated. It is found that the oxidation resistance of the alloys with low Y contents (0Y and 2Y) made from 20 h-milled powders is worse than that of the alloys made from 4 h-milled powders. It is because the protective WO3/SiO2 composite layer is discontinuous. While the alloys with high Y contents (4Y and 6Y) made from 4 h and 20 h-milled powders show good oxidation resistance. Even, the thickness of the oxide layer of the alloys with 4Y and 6Y made from 20 h-milled powders after oxidation at 1000 ℃ for 2 h is 84.0 μm and 70.7 μm, less than that made from 4 h-milled powders. This is due to the size and distribution of W5Si3, Y2Si2O7 aggregates and W-Y-O melt. The synergistic effects of Y contents and milling time on the microstructures and oxidation resistance of the alloys are revealed.

Controlling robots in space with necessarily low material and structural stiffness is quite challenging at least in part due to the resulting very low structural resonant frequencies. The frequencies are sometimes so low, the vary act of controlling the robot with medium or high bandwidth controllers lead to excitation of resonant vibrations. Biomimetics or biomimicry emulates models, systems, and elements of nature for solving such complex problems. Recent seminal publications have re-introduced the viability of optimal command shaping, and one recent instantiation mimics baseball pitching to propose control of highly flexible space robots. The readership will find a perhaps dizzying array of thirteen decently performing alternatives in the literature but could be left bereft selecting a method(s) deemed to be best suited for a particular application. Bio–inspired control of space robotics is presented in a quite substantial (perhaps not comprehensive) comparison, and the conclusions of the study indicate the top three performing methods based on minimizing control effort (i.e., fuel) usage, tracking error mean, and tracking error deviation include.

ABSTRACT Heavy metals have been classified as dangerous environmental pollutants. Interest in feasible ways to reduce heavy metals pollution is a noble goal. Adsorption is an effective method based on its effectiveness and low- cost. Nowadays, low-cost bio-sorbents have been utilized to replace costly expensive adsorbents. Rich cellulose materials are effective heavy metal adsorbents, and their performance can be enhanced via chemical modification. The present work reviews the steady progress in the utilization of agriculture by-product wastes as heavy metal bio-sorbent. The unique advantages of these by-products such as renewability, abundance, simple processing, and low cost, justifier this work. The results confirm that the chemically treated agro-wastes exhibit high- removal efficiency (reaches 95% in most cases). The adsorption isotherm studies indicate that the concentration of the metal ions has a significant effect on the adsorption process. The Freundlich model provides a physical adsorption model of the metal ions on the bio-sorbent surface. Langmuir isotherm offers an estimate of the effect of different factors on the efficiency of the process. The adsorption kinetics studies offer an idea of reaction pathways including the adsorption mechanism and the efficiency of the metal ion removal. Applying the pseudo-first-order and pseudo-second-order models describes the adsorption kinetics. This information can be utilized in developing effective strategies to remove heavy metal ions using chemically treated agro-waste. The data confirmed that chemical modification is a significant parameter in the efficiency of metal ion removal. The feasibility and effectiveness of using these cellulosic by-products as bio-sorbent should be given attention and encouraged.

The single set of electron transporters of the cardiac mitochondrial respiratory chain is organized into three separate supercomplexes. Two of them contain complex I, a dimer of complex III, and two dimers of complex IV. The third supercomplex contains a dimer of complex III and two dimers of complex IV. We also considered two important discoveries. First, the enzymes of β-oxidation of fatty acids are physically associated with respirasome. Second, β-oxidation of fatty acids creates the highest level of QH2 and reverses the flow of electrons from QH2 through complex II, reducing fumarate to succinate. We argue that the respirasome is uniquely adapted for the β-oxidation of fatty acids. The acyl-CoA dehydrogenase complex reduces the membrane’s pool of ubiquinone to QH2, which is instantly oxidized by the 2complex III-4complex IV supercomplex, generating high energization of mitochondria and reversing the electrons flow through the complex II, which reverses the electrons flow through the complex I increasing the NADH/NAD+ ratio in the matrix. The mitochondrial nicotinamide nucleotide transhydrogenase catalyzes a hydride (H-, a proton plus two electrons) transfer across the inner mitochondrial membrane, reducing the cytosolic pool of NADP(H), thus providing the heart with ATP for muscle contraction and energy and reducing equivalents for the housekeeping processes.

The biofibres wide application as mortars enhancement have been so far restricted by factors related to their chemical composition and hygroscopic nature. Their hydrophilic behavior increases the water demand of mortar-mixtures and diminishes their adhesion to the matrix, while further moisture-related fibre degradation issues may arise. Additionally, the natural fibres seem to be susceptible to degradation caused during the exposure to alkaline environments conditions, such as those of cement mortars, restricting their utilization in construction industry. Therefore, the current study focusses on the potential of fibre modification through treatments that would permanently alter their structure and chemical composition in the whole mass or surface towards their performance improvement. In this study, mild hydrothermally treated wood fibres of black pine and beech species were prepared and incorporated in cement mortars to assess their performance, applying the proportion of 1.5% v/v in the mortar. The mortars workability (at fresh state), physical, hygroscopic, chemical, thermal, and mechanical characteristics at the age of 28, 90 and 365 days and weathering performance by subjecting them at different artificial ageing environments (freeze-thaw cycles or outdoor exposure) were examined. The results indicated the beneficial role of the treated fibres in the dimensional stability, flexural strength, thermal insulation properties and capillary absorption of the mortar specimens, especially during ageing process, with the black pine fibres to reveal the highest improvement. The hydrothermally treated wood fibres seem to ensure the integrity maintenance of cement mortars under all ageing conditions, proving that the specific bio-additives could provide low-cost and eco-friendly mortar enhancement pathways.

The microstructure evolution of SCM435 cold heading steel at different cooling rates was investigated by means of scanning electron microscopy, TEM, XRD, and electron backscatter diffraction. The results show that the cooling rate has a significant effect on the microstructure of the experimental steel. With an acceleration of the cooling, the microstructure of the steel gradually changed from ferrite and pearlite to ferrite, pearlite, and granular bainite; finally, the pearlite disappeared, and the microstructure changed to acicular ferrite, bainite, and martensite. With an increase in the cooling rate, the morphology of the carbide underwent an evolution from sheet carbide to short-rod carbide, granular carbide, and ultimately thin-strip carbide. With the acceleration of cooling, the proportion of large-angle grain boundaries gradually decreased, and the area of small-angle grain boundaries gradually increased. When the cooling rate was 0.1℃/s, the proportion of large-angle grain boundaries was as high as 52.8%, and the dislocation density was only 1.91 × 1012 cm−2. When the cooling rate was 2.0℃/s, the proportion of large-angle grain boundaries was only 27.1%, and dislocation density increased to 5.38 × 1012 cm−2. With the increase in the cooling rate, the depth of the decarbonization layer and the thickness of the scale oxide gradually decreased, the proportion of FeO phase in the scale phase gradually decreased, and the proportion of Fe3O4 phase and Fe2O3 phase gradually increased. The tensile strength increased monotonously with the increase in cooling rate, whereas the elongation and shrinkage first decreased, then increased, and then decreased. When the cooling rate was 1.0 m/s, the short rod and granular bainite in the material structure endowed the SCM435 steel with excellent strength and toughness matching, and the tensile strength and elongation of the steel reached 895 MPa and 24%, respectively.

The Reactive Spark Plasma Sintering (R-SPS) method is compared in this work with the two-steps SHS-SPS route, based on combination of the Self-propagating High-temperature Synthesis (SHS) with the SPS process, for the fabrication of dense (Hf0.2Mo0.2Ti0.2Ta0.2Nb0.2)B2-SiC and (Hf0.2Mo0.2Ti0.2Ta0.2Zr0.2)B2-SiC ceramics. A multiphasic and inhomogeneous product, containing various borides, is obtained at 2000°C/20min by R-SPS, from transition metals, B4C and Si. In contrast, if the same precursors are first reacted by SHS, and then processed by SPS under the optimized condition of 1800°C/20min, the desired ceramics are successfully attained. Both High-Entropy-Boride/SiC products display densities > 97%, uniform microstructures and contained only small amounts of residual oxides (<2.4 wt.%). The presence of SiC makes the sintering temperature milder, i.e. 150°C below to that needed by the corresponding additive-free system. Fracture toughness is also markedly improved, particularly when considering the Nb-containing system processed at 1800°C/20min, whereas KIC progressively decreases (from 7.35 to 5.36 MPa m1/2) as the SPS conditions become more severe. SiC addition is found to inhibit the volatilization of metal oxides like MoO3 formed during oxidation experiments, thus avoiding mass loss in the ceramics. The benefits above also likely take advantage of the fact that the two composite constituents are synthesized in parallel, according to the SHS-SPS approach, rather than being produced separately and combined subsequently, so that strong interfaces between them are formed.

Cannabinoid metabolites have been reported to be more potent than the parent compounds. Among them, Ajulemic acid (AJA) is a synthetic analogue of Δ9-THC-11-oic which will be a good template structure for discovery of more potent analogues. Herein, we optimized the key allylic oxidation step to introduce the C-11 hydroxy group with high yield. And a series of compounds were prepared with this condition applied including HU-210, 11-Nor-Δ8-Tetrahydrocannabinol-9-carboxylic acid and Δ9-THC-COOH.

Harnessing the Remarkable Bio-Remediation Potential of Vernonia spp. for the Sustainable Restoration of Hydrocarbon-Polluted Clay Soil in Ogoni Land, Nigeria This study explores the potential of utilizing Vernonia spp. for eco-friendly bio-remediation of hydrocarbon-polluted clay soil in Ogoni Land, Nigeria. The aim is to find a sustainable and effective solution that promotes the restoration of the polluted soil while minimizing the use of external additives. The process of bio-remediation can occur naturally, through natural attenuation or intrinsic bio-remediation. However, it has been observed that in certain cases, the addition of fertilizers, oxygen, or organic matter is required to enhance the effectiveness of bio-remediation. In this research, we focus on the bio-remediation potential of Vernonia spp., a native plant species known for its strong phytoremediation abilities. By harnessing the remarkable bio-remediation properties of Vernonia spp., we seek to restore the hydrocarbon-polluted clay soil in Ogoni Land in an environmentally friendly and sustainable manner. Our methodology involves conducting greenhouse experiments to assess the bio-remediation efficiency of Vernonia spp. in different soil conditions. We will analyze the soil's physical and chemical properties, as well as the degradation of hydrocarbons over time. The experimental results will provide valuable insights into the effectiveness of Vernonia spp. in removing hydrocarbon pollutants from clay soil. Through this study, we aim to develop a cost-effective and sustainable approach to restore hydrocarbon-polluted clay soil in Ogoni Land. By leveraging the natural bio-remediation potential of Vernonia spp., we can potentially reduce the reliance on external additives, thus minimizing the environmental impact associated with traditional remediation methods. The research article explores methods to promote the growth of pollution-eating microbes in order to enhance bio-remediation. Bio-remediation refers to the use of naturally occurring organisms to break down harmful substances into less toxic or non-toxic forms. In situ bio-remediation involves treating the contaminated material directly at the site, while ex-situ bio-remediation involves removing the contaminated material for treatment elsewhere. This study specifically investigates ex-situ bio-remediation techniques for hydrocarbon-contaminated clay soil. The researchers found that the application of room dry and wet blended bitter leaf showed promising results in the bio-remediation of hydrocarbons in the clay soil. Using Vernonia galamensis, a concentration as high as 0.55 ug/ml was achieved, while Vernonia amygdalina yielded a concentration as high as 0.67 ug/ml when applied at 35g and 40g respectively, based on the wet blended approach. These findings highlight the effectiveness of wet blended Vernonia species in the bio-remediation process.During the remediation process of the clay soil, the pH levels showed a trend of increasing from acidic to normal to alkaline. This can be attributed to the remediation of excessive metals present in the soil. After 40 days, the pH of the clay soil reached 6.97 when treated with 40 grams of Vernonia galamensis, and 7.00 when treated with 40 grams of Vernonia amygdalina. Interestingly, while the remediation efficiency of HC (hydrocarbon) decreased with increasing mass of Vernonia galamensis, the remediation efficiency of HC increased when using Vernonia amygdalina. These observations highlight the varying effects of different Vernonia species on hydrocarbon remediation.The highest remediation values were observed when using Vernonia galamensis at 35g and Vernonia amygdalina at 40g. These particular amounts of these Vernonia species demonstrated effective remediation of the targeted pollutants. However, in comparison to other metals, the remediation effects were relatively lower for zinc (Zn), with only approximately 0.25 ug/ml being remediated. This suggests that the remediation potential of the Vernonia species may vary depending on the specific contaminant.The higher remediation effects observed for Zn metal in the soil can be attributed to the wet blended preparation method of the Vernonia species. In contrast, the room dried Vernonia species exhibited the lowest performance in remediating the soil, with approximately 0.17 ug/ml and 0.10 ug/ml remediation for galamensis and amygdalina, respectively. Both Vernonia leaf extracts achieved a remediation of 0.5 ug/ml for chromium. The sun dried and room dried methods also showed considerable remediation potential, with values above 0.4 ug/ml. The level of significance for the model was attained at 0.05, and the r2 value was appreciable. These findings indicate the effectiveness of different preparation methods and Vernonia species in soil remediation

By planting LEDs on the surfaces of orifice baffles, a novel batch oscillatory baffled photoreactor (OBPR) together with polymer-supported Rose Bengal (Ps-RB) beads are used to investigate reaction kinetics of a photo-oxidation reaction between α-terpinene and singlet oxygen (1O2). In the widely used NMR data analysis for this reaction, α-terpinene and ascaridole are treated as a reaction pair, assuming kinetically singlet oxygen is in excess or constant. We have, for the first time, examined the validity of the method, discovered that increasing α-terpinene initially leads to an increase of ascaridole, indicating that the supply of singlet oxygen is in excess. Applying kinetic analysis, a pseudo first order reaction kinetics is confirmed, supporting this assumption. We have subsequently initiated a methodology of estimating the 1O2 concentrations based on the proportionality of ascaridole concentrations with respect to its maximum under these conditions. With the help of the estimated singlet oxygen data, the efficiency of 1O2 utilization and the photo efficiency of converting molecular oxygen to 1O2 are further proposed and evaluated. We have also identified conditions where further increase of α-terpinene has caused decreases in ascaridole, implying kinetically that 1O2 has now become a limiting reagent, the method of treating α-terpinene and ascaridole as a reaction pair in the data analysis would no longer be valid under those conditions.

This research explores the enhancement of bio-oil quality through upgrading with the magnetic bimetallic oxide (CuO-Fe3O4) catalysts supported on the activated rice straw biochar (AcB). These catalysts were employed in a supercritical ethanol-based upgrading process. Various characterization techniques, including elemental analysis, XRD, BET, TGA, and SEM, were utilized to characterize the prepared catalyst. The study revealed significant improvements in the physical characteristics and chemical composition of the bio-oil, with higher heating value (HHV) increasing from 21.3 to 32.1 MJ/kg. Esterification and transesterification were identified as key reactions contributing to this improvement. Notably, the pH of bio-oil increased from 4.3 (raw bio-oil) to 5.63 (after upgrading), signifying reduced acidity. The analysis of the bio-oil's chemical composition highlighted a decrease in oxygen content and an increase in carbon and hydrogen content. At the optimum conditions, the application of supercritical ethanol proved to be an efficient method for enhancing the bio-oil's properties. A crucial transformation occurred during the upgrading process and more than 90% % of carboxylic acids were converted into esters, primarily ethyl acetate at the optimal conditions. This study has demonstrated the effective enhancement of raw bio-oil from rice straw through the utilization of carbon-based bimetallic oxide catalysts in a supercritical upgrading procedure.

The design of binders plays a pivotal role in achieving enduring high power in lithium-ion batteries (LIBs) and extending their overall lifespan. This review underscores the indispensable characteristics that a binder must possess when utilized in LIBs, considering factors such as electrochemical, thermal, and dispersion stability, compatibility with electrolytes, solubility in solvents, mechanical properties, and conductivity. In the case of anode materials, binders with robust mechanical properties and elasticity are imperative to uphold electrode integrity, par-ticularly in materials experiencing substantial volume changes. For cathode materials, the se-lection of a binder hinges on the crystal structure of the cathode material. Other vital consid-erations in binder design encompass cost-effectiveness, adhesion, processability, and envi-ronmental friendliness. Incorporating low-cost, eco-friendly, and biodegradable polymers can contribute significantly to sustainable battery development. This review serves as an invaluable resource for comprehending the prerequisites of binder design in high-performance LIBs and offers insights into binder selection for diverse electrode materials. The findings and principles articulated in this review can be extrapolated to other advanced battery systems, charting a course for the development of next-generation batteries characterized by enhanced perfor-mance and sustainability.

Keywords: Trichoderma sp., biogenic selenium nanoparticles, capping biomolecules, bio-corona, agriculture, plant biostimulants, phytopathogens, physicochemical properties, bioactivity mechanism

Metachrony is defined as coordinated asynchronous movement throughout multiple appendages, such as the cilia of cells and swimmerets of crustaceans. We investigate the process of metachronal propulsion, notably used by species of crustaceans and microscopic cells to move through fluid. A rigid crustacean model with paddles moving in symmetric strokes was created to simulate metachronal movement. Coupled with the surrounding fluid domain, we employ the immersed boundary method to analyze fluid-structure interactions. To explore the effect of nonlinear morphology on the efficiency of metachronal propulsion, we generate and simulate a range of crustacean body shapes, from upward curves to downwards curves. We found that the highest propulsion velocity is achieved when the crustacean model morphology follows a downwards curve, specifically a parabola of leading coefficient k=−0.4. This curved morphology results in 4.5% higher velocity compared to the linear model. As k deviates from −0.4, the propulsion velocity decreases with increasing magnitude, forming a concave downward trend. The impact of body shape on propulsion velocity is shown by how the optimal velocity with k=−0.4 is 71.5% larger than the velocity at k=1. Overall, this study suggests that morphology has a significant impact on metachronal propulsion.

In the context of high-temperature water vapor treatment, Zn-Mg-Al alloy-coated steel sheets exhibit the emergence of a black surface. This study aims to explore the factors and mechanisms contributing to surface blackening by inducing black surfaces on Zn-Mg-Al alloy-coated steel sheets, which were fabricated through molten coating subjected to water vapor treatment at 150 degrees Celsius. The surfaced composition was predominantly identified as ZnO, a zinc oxide film, validated through X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Morphological analysis of the surface and cross-section post-water vapor treatment revealed a disrupted lamellar structure with diffused features, resulting in the formation of an oxide film. Optical properties analysis demonstrated an increased absorbance and a decreased bandgap energy after water vapor treatment, indicative of an augmented blackening effect. Consequently, the high-temperature water vapor treatment led to the formation of oxides on the surface, with the highly reactive Mg and Al extracting oxygen from the predominantly present ZnO surface. This process resulted in the creation of an oxygen-deficient oxide, ultimately causing surface blackening.

The main objective was to analyze the influence of silicon content on high-temperature oxidation of low-alloy steels. Samples of AISI 1045, AISI 5160, and AISI 9254 steels, with different silicon contents, were oxidized at an isothermal temperature of 1000°C for times of 20 minutes, 40 minutes, and 60 minutes. The oxide layers formed mainly contain hematite, magnetite wustite, and fayalite. The average thickness of the oxide layer can decrease with an increase in silicon content below 1% but can increase for contents greater than 1% due to the difference in density between fayalite and iron oxides. Silicon tends to accumulate on the surface of steel and form a SiO2 film in the early stages of oxidation, which can control the oxidation process. The eutectic compound FeO+Fe2SiO4 forms at the oxide-steel interface, and its thickness increases with oxidation time and the silicon content present. The SiO2 film tends to decrease with oxidation time and silicon content.

A soluble biopolymer (SBP) was obtained by hydrolysis in pH 13 water at 60 °C. The dry product was re-dissolved in plain water at pH 10 and used as control against the same solution added with hydrogen peroxide at 0.1-3 H2O2 moles per SBP carbon mole. The control and test solutions were kept at room temperature, in the dark or in a climatic chamber under irradiation with simulated solar light, until the solutions pH remained constant. Afterwards, the solutions were processed to recover and analyze the crude soluble products. For the control solution, the results indicated significant production of CO2, production of organic carboxyl functional groups and de-polymerization of the pristine SBP organic matter. These findings demonstrate the oxidation of SBP by water, which could only occur through the production of O and OH radicals catalyzed by SBP. The present work reports the results obtained from the control solution and for the test solution treated in the presence and absence of H2O2, with and without pH control, in the dark and under irradiation with simulated solar light. The paper discusses the perspectives of further implementation of the autocatalytic properties of SBP for the realization of a municipal biowaste-based biorefinery producing value added bio-products for consumer’s use.

Indigo leaves form various plant species are sources of dyes/pigments, not fully exploited for making sustainable textiles. Blue indigo vat dye extracted from indigo leaves, yields high wash colorfastness but fades slowly with light, and is not easily used for direct printing. Indigo leaves can be used to produce textiles of various color shades, while light resistant Mayan-inspired hybrid pigments have not yet been used for textile coloring. Using blue indigo dyes from 3 plant species, with exhaustion dyeing, intense wash resistant blue colored textiles are produced, and in the case of Indigofera Persicaria tinctoria, textiles have antibacterial activity against S. Epidermis and E. Coli.100% Natural Mayan-inspired blue indigo pigment, made from Sepiolite clay and indigo dye, was used both in powdered and paste forms to perform pigment textile dyeing by pad cure process, and direct screen printing on textiles. A water-based bio-binder (40%) was used efficiently for both padding and printing. Bio-based Na Alginate thickener allowed color fast printing on both polyester and cotton fabrics, while bio-based glycerin allowed good print color fastness on polyester only, yielding prints with excellent color fastness to wash (5/5), to dry and wet rubbing (5/5) and light (7/7).

Benzylsuccinate is generated in anaerobic toluene degradation by radical addition of toluene to fumarate and further degraded to benzoyl-CoA by a beta-oxidation pathway. Using metabolic modules for benzoate transport and activation to benzoyl-CoA and the enzymes of benzylsuccinate beta-oxidation, we established an artificial pathway for benzylsuccinate production in Escherichia coli, which is based of its degradation pathway running in reverse. Benzoate is supplied to the medium, but needs to be converted to benzoyl-CoA by an uptake transporter and a benzoate-CoA ligase or CoA-transferase. In contrast, the second substrate succinate is endogenously produced from glucose under anaerobic conditions, and the constructed pathway includes a succinyl-CoA:benzylsuccinate CoA-transferase that activates it to the CoA-thioester. We present first evidence for the feasibility of this pathway and explore product yields under different growth conditions. Compared to aerobic cultures, the product yield increased more than 1000-fold in anaerobic glucose-fermenting cultures and showed further improvement under fumarate-respiring conditions. An important bottleneck to overcome appears to be product excretion, based on much higher recorded intracellular concentrations of benzylsuccinate, compared to those excreted. While no export system is known for benzylsuccinate, we observed an increased product yield after adding an unspecific mechanosensitive channel to the constructed pathway.

We used ab initio molecular dynamics simulations to compare the activation of 2-propanol on the low index Co3O4 (111), (110) and (001) surfaces in dry conditions. The thermal and surface assisted decomposition of a film of 2-propanol to 2-propoxide on the B-termination of each surface was monitored and analyzed. The investigations suggest an activity order of Co3O4 (111) > (110) > (001). On the B-terminated (111) surface, full dissociation of all 2-propanol molecules at the interface is observed, accompanied by a Mars-van Krevelen-type mechanism upon hydroxylation of the surface. On the (110) surface, 2-propanol dissociation is driven by temperature, which activates the two-fold coordinatively unsaturated surface oxygens. The (001) surface on which almost no dissociation occurs is the least active. No formation of acetone is observed in the simulations conditions.

Boron carbide (B4C) powders with defined stoichiometry, high crystallinity, minimal impurity content, and a fine particle size are imperative for realizing the exceptional properties of this compound in advanced high-technology applications. Nevertheless, achieving the desired stoi-chiometry and particle size using traditional synthesis methods, which rely on prolonged, high-temperature processes, can be challenging. The primary objective of this study is to syn-thesize fine B4C powders characterized by high crystallinity and a sub-micron particle size, em-ploying a fast, and energy-efficient method. B4C powders are synthesized from elemental boron and carbon in a high-frequency induction heating furnace using the Electromagnetic Induction Synthesis (EMIS) method. The rapid heating rate achieved through contactless heating promotes the ignition and propagation of the exothermic chemical reaction between boron and carbon. Additionally, electromagnetic effects accelerate atomic diffusion, allowing the reaction to be completed in an exceptionally short timeframe. The grain size and crystallinity of B4C can be finely tuned by adjusting various process parameters, including the post-ignition holding temperature and the duration of heating. As a result, fine B4C powders can be synthesized in under 10 minutes. Moreover, these synthesized B4C powders exhibit high resistance to oxidation when exposed to air.

Cobalt-doped alumina catalysts were prepared by different methods, applying either the conventional wet impregnation (WI) and/or the advanced spray impregnation (SI), and evaluated as novel oxidation catalysts for CO and MeOH oxidation. The spray impregnation technique aims towards the synthesis of core-shell catalytic nanostructures to secure chemical/thermal stability of the active sites on the catalyst carrier. The catalysts were further promoted with low Pd content (0.5 wt.%) applying either incipient wetness impregnation (DI) or spray impregnation. The results revealed the superior performance of spray impregnated catalysts (Co/γ-Al2O3-SI) for both reactions. The deposition of Co oxide on the outer surface of the alumina particle (SEM images) and the availability of the active Co phase, resulted in the enhancement of Co/γ-Al2O3 catalysts oxidation activity. Pd incorporation increased catalysts reducibility (TPR-H2) and improved the catalysts performance for both reactions. However, Pd incorporation method affected the catalytic performance; as with the SI method the active phase of Co3O4 was probably covered from PdO and was not available for the oxidation reactions. On the contrary, the incorporation of Pd with the DI method resulted in better dispersion of PdO all over the Co/Al catalyst surface, maintaining available Co active sites and better Pd-Co interaction. MeOH desorption studies revealed the methanol oxidation mechanism; Co/Al catalysts promote partial oxidation of MeOH to formaldehyde (HCHO) and dehydration to dimethyl ether (DME), while Pd-based Co/Al catalysts enhance the complete oxidation of methanol to CO2 and H2O.

The interaction between O2 and reduced ceria nanocubes was mainly investigated by FTIR spectroscopy. Nanorods and nanoparticles were also studied for comparison. Adsorption of O2 at 100 K on unreduced ceria produces only O2 molecularly adsorbed on Ce4+ sites. The Ce3+ cations in H2-reduced ceria were monitored by the 2F5/2 → 2F7/2 electronic transition band at 2133-2095 cm-1. This band possesses a fine structure well resolved at 100 K. The positions of the individual components depend on the Ce3+ environment, including the presence of nearby species such as OH groups. Even at 100 K, the interaction of O2 with reduced ceria leads to fast oxidation of about half of the Ce3+ cations, including all Ce3+ sites bound to OH groups and carbonates, and the simultaneous formation of superoxo (O2) and peroxo (O22) species. The remaining fraction of Ce3+ sites disappears upon heating up to 348 K. At higher temperatures, the peroxo species decompose directly, yielding lattice oxygen. Superoxides are converted to hydroperoxides, which then decompose to terminal OH groups. Reduced samples evacuated at T &lt; 773 K contain sorbed H2. Part of this hydrogen is also fast oxidized to H2O even at 100 K.

Abstract: Important variables that affect the quality and functionality of sperm and may affect male reproductive health and fertility include telomere length, mitochondrial content, and the ratio of mitochondrial DNA (mtDNA) to nuclear DNA (nDNA). The purpose of this study was to look at the connections between these three sperm characteristics and how they might affect a woman's ability to conceive. Methods: Data were collected from 82 men who underwent IVF/ICSI at the University Hospital of Ioannina's IVF Unit in the Obstetrics and Gynecology Department. Evaluations included sperm morphology, sperm count, sperm motility, and participant history. To address this, males of reproductive age who were categorized into three body mass index (ΒΜΙ) groups—normal, overweight, and obese—had their sperm samples tested. Results: Our findings indicate a negative correlation between relative telomere length and ΒΜΙ for both the normal and overweight groups. Conversely, a positive correlation was observed for the obese group, indicating a possible relationship between mitochondrial health and telomere maintenance. The results were statistically significant only for the obese group. Furthermore, a negative correlation was observed between telomere length and mitochondrial content in both the normal and overweight groups, indicating that a lower mitochondrial content may be linked to longer telomeres. Nonetheless, there was a positive correlation for the group that was obese. For all three groups, the data did not reach statistical significance. Given that mitochondrial con-centration and telomere length are both markers of cellular integrity and health, these correla-tions may have an impact on the quality of sperm. Furthermore, the relative telomere length of the normal and overweight groups had a negative correlation with the ratio of mtDNA to nDNA, though the obese group showed a positive correlation. The findings were not statistical-ly significant in any of the groups under investigation. According to this, male fertility may be negatively impacted by an imbalance in the copy number of the mitochondrial genome com-pared to the nuclear DNA in sperm. Conclusions: Our research, in essence, emphasizes the interaction among human sperm telo-mere length, mitochondrial concentration, and the mtDNA to nDNA ratio. Gaining knowledge of these correlations could help explain the reasons behind male infertility and open up new treatment options for reproductive health problems. The functional importance of these correla-tions and possible uses in therapeutic contexts require more investigation.

Introduction: The distribution of typical bacterial redox enzymes such as pyruvate-ferredoxin oxidoreductase (PFOR) in protozoa remains interestingly puzzling. Previous studies have demonstrated diverse cellular localizations of PFOR in amitochondriate anaerobic protozoa such as Trichomonas vaginalis. PFOR is of particular pharmacological importance because it catalyzes the reductive bio-activation of nitro-based prodrugs to cytotoxic radical metabolites. Metronidazole was developed primarily as an antiprotozoal agent against infections caused by T. vaginalis. However, its antimicrobial spectrum was subsequently expanded to cover anaerobic bacterial infections. It has been shown that mutations in the genes encoding PFOR result in inherent resistance of T. vaginalis and anaerobic bacteria to metronidazole. Aims: To analyze the phylogenetic distribution of PFOR in selected protozoa and bacteria using proteins encoded by housekeeping genes as controls. Using comparative bioinformatics to test the hypothesis that PFOR was most likely acquired through horizontal gene transfer from bacteria, proteome-wide analysis and gene expression analysis to identify other genes that were putatively acquired through horizontal gene transfer from bacteria to protozoa. Methods: Sequence similarity queries were performed using the proteins of interest against the NCBI non-redundant protein sequence database with BLASTP version 2.12.0+ from the NCBI website. Multiple sequence alignments were performed with MEGA version X software using the Muscle algorithm. These were then exported in Mega format to construct phylogenetic trees using the neighbor-joining algorithm and the Poisson substitution model. Complete proteomes of representative protozoan and bacterial species were downloaded in fasta format from the ensemblgenomes database. HMM profile libraries were used to screen the proteomes with hmmscan of the HMMer package. Whole proteome BLAST searches were performed between protozoan species of interest against closely related protozoa. The results were compared to the proteome BLAST against the intestinal bacteria Desulfovibrio vulgaris. Gene enrichment analysis was performed between the exclusively present proteins in the protozoa and D. vulgaris. Only results with p-values <0.05 were considered for analysis. Results and conclusions: A plausible explanation for the restricted occurrence of PFOR in protozoa is based on the hypothesis that bacteria serve as potential sources of genes that enhance optimal adaptation of protozoa in hostile environments. The expanded cladograms of Entamoeba and Cryptosporidium with their closely related genera substantiated this hypothesis. The exclusively expressed proteins obtained from E. histolytica and the putative bacterial gene donor, D. vulgaris, showed an over-representation of eleven genes involved in small molecule metabolism, generation of precursor metabolites, and carbohydrate metabolism. If these results can be reproduced in other PFOR-possessing protozoa, it would provide a more validated evidence to support the horizontal transfer of pfor from bacteria. Subsequent syntenic analyses of the significantly enriched genes would be required to provide further information regarding the positional relatedness of these genes at the chromosomal level. Since metronidazole is an established and well tolerated drug for treating infections caused by PFOR-possessing pathogens, it can be considered as a potential drug candidate for the treatment of infections caused by Cryptosporidium, Spironucleus and Blastocystis.

The effects of rare earth Y content on the microstructure and high-temperature oxidation properties of 47Fe-36Ni-15Cr-1.5Mn alloy at 1000°C were investigated. The results show that 47Fe-36Ni-15Cr-1.5Mn alloy oxidizes at 1000°C under laboratory atmospheric pressure to form an oxide film layer dominated by Cr2O3 and (Fe, Ni, Mn) Cr2O4 spinel, and the oxidation curve of the alloy follows the parabolic law. After the addition of rare earth Y, rare earth phases precipitated along the grain boundaries in the alloy, and the more Y content, the more precipitated phases in the grain boundaries. The alloy with added rare earths was oxidized at a high temperature of 1000 °C for 2160 min, the oxidation law still followed the parabolic law, while the rare earth phase at the grain boundary reacted with the oxygen atoms infiltrated from the outside to generate a rare earth Y-rich oxide residing at the boundary between the grain boundary and the precipitated phase of the alloy. Add 0.5 wt.% rare earth Y 47Fe-36Ni-15Cr-1.5Mn-0.5Y alloy 1000 ° C high temperature oxidation of the formation of spinel oxide crystalline particles, dense and complete oxide film layer, the surface of the addition of a small amount of (0.5 wt.%) rare earth Y after the refinement of the oxide particles, and in the alloy grain boundaries in the form of oxides reside in the alloy to inhibit the cations in the matrix and the oxygen negative ions. and oxygen-negative ions in the alloy matrix, improving the antioxidant performance of the alloy. With the further increase of rare earth Y, during the oxidation of the alloy at high temperature, the precipitation phase at the grain boundary promotes the inward diffusion of oxygen, resulting in the deterioration of the antioxidant property of the alloy.

Flavin-dependent monooxygenases (FMOs) have made substantial influence as catalysts for monooxygenation reactions, impacting diverse field such as drug metabolism, environmental studies, and natural product synthesis. Their application in biocatalysis boasts several advantages over conventional chemical catalysis, such as heightened selectivity, safety, sustainability, and eco-friendliness. In the realm of biomedicine, FMOs are pivotal in antibiotic research, modulating natural products, antimicrobial agents, and pathways involved in drug synthesis. They're also underscored as potential pharmaceutical targets, pivotal in disease progression and viable for therapeutic intervention. Additionally, FMOs play a substantial role in environmental science, especially in pesticide processing and plant vitality. Their involvement in biosynthesizing compounds like polyethers, tropolones, and ω-hydroxy fatty acids, with remarkable regio- and stereoselectivity, renders them indispensable in drug discovery and development. As our comprehension of FMOs' catalytic mechanisms and structures advances, coupled with cutting-edge biotechnologies like computational design and directed evolution, FMOs are poised to occupy an increasingly significant role in both scientific exploration and industrial applications.

The results of the investigation showed that second-order kinetics govern the adsorption process, and the corresponding rate constants were found. To evaluate the parameters related to the adsorption process, the adsorption equilibrium was examined using a variety of mathematical models, such as the Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherm models. The Langmuir isotherm was found to be the best appropriate among all models for describing the adsorption of Cu2+ and Ni2+ ions using bio-nanocomposite beads. The positive values of ΔH° indicate that the adsorption is physical and endothermic, in agreement with experimental results. The negative value of ∆G° shows that the adsorption process is spontaneous. Positive ΔS° values indicate increased randomness at the solid/liquid interface, during adsorption of Cu2+ and Ni2+ cations onto the engineered bio-nanocomposite. The maximum adsorbed amounts of metal ions by the bio-nanocomposite used were 370.37 mg/g for Ni2+ and 454.54 mg/g for Cu2+ from single system. For the binary system, according to the Langmuir isotherm, the maximum adsorbed amounts of Ni2+ and Cu2+ were 357.14 mg/g and 370,37 mg/g, respectively. There is proof that Alginate-Moroccan clay bio-nanocomposites can serve as a different, less expensive source of sorbents for the removal of metal ions from single and binary systems.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

Obesity and physical activity have opposing effects on cardiorespiratory fitness. This study aimed to investigate the impact of obesity measured by various anthropometric indicators and physical activity level on oxygen uptake and fat oxidation during moderate-intensity aerobic exercise in adults. Forty-eight individuals were recruited. Various anthropometric indicators (i.e., body mass index (BMI), waist circumference (WC), waist-to-hip ratio (WHR), and waist-to-height ratio (WHtR)) were measured. Physical activity was assessed using the International Physical Activity Questionnaire (a short version). Total oxygen uptake (VO2tot) and fat oxidation were recorded during 30-minute aerobic exercise at moderate intensity. There were no differences in oxygen uptake and fat oxidation between obese and non-obese groups. Based on obesity and physical activity, VO2tot was significantly different among groups classified by WHR. Inactive obesity had significantly lower VO2tot 28.1% compared to active obesity and 29.2 % compared to active non-obesity. The inactive obesity had a 3.8%, 27.4%, and 4.3% lower fat oxidation than the active non-obesity, as classified by WC, WHR, and WHtR, respectively. However, the differences were not statistically significant. We conclude that active obesity, as measured by WHR, exhibited higher oxygen uptake compared to inactive obesity. Moreover, inactive obesity showed poorer oxygen uptake than active non-obesity.

Given its exceptional attributes, aerogel is viewed as a material with immense potential. Being a natural polymer, cellulose offers the advantage of being both replenishable and capable of breaking down naturally. Cellulose-derived aerogels encompass the replenish ability, biocompatible nature, and ability to degrade naturally inherent in cellulose, along with additional benefits like minimal weight, extensive porousness, and expansive specific surface area. Even with increasing appreciation and acceptance, the undiscovered possibilities of aerogels within the textile sphere continue to be predominantly uninvestigated. In this context, we outline the latest advancements in the study of cellulose aerogel formulation and their diverse impacts on textile formations. Drawing from the latest studies, we reviewed the materials used for the creation of various kinds of cellulose-focused aerogels and their properties, analytical techniques, and multiple functionalities in relation to textiles. This comprehensive analysis extensively covers the diverse strategies employed to enhance the multi-functionality of cellulose-based aerogels in the textile industry. Additionally, we focused on the global market size of bio-derivative aerogels, companies in the industry producing goods, and prospects moving forward.

Naphtho[1,8-de][1,2]oxazin-4-ol and its acyl or benzyl derivatives ring open to various 2,8-dihydroxy-1-naphthonitriles, that undergo methylation, reduction, demethylation and debenzylation reactions, to afford the target compound (E)-2-hydroxy-8-methoxy-1-naphthaldehyde. The best overall yield of the latter was 28.7%. This compound was converted to its corresponding (E)-2-hydroxy-8-methoxy-1-naphthaldehyde ox-ime, which was oxidatively o-cyclized with phenyliodine(III) diacetate (PIDA) to 9-methoxynaphtho[1,2-d]isoxazole 2-oxide. The latter in deuterated DMSO, at room temperature, rearranged to its isomer to 2-hydroxy-8-methoxy(naphthalen-1-yl)nitrile oxide. The isomeriza-tion was detected by a time-course plot 1H NMR spectroscopy and further identified from its13C NMR and HRMS spectra. The nitrile oxide was stable in (non)deuterated DMSO for at least 18 hours. A 3,4-bis(2-hydroxy-8-methoxynaphthalen-1-yl)-1,2,5-oxadiazole 2-oxide as a dimeriza-tion product or an isocyanate as a rearrangement isomer were both ruled out, the former by the absence of the relevant molecular ion in its HRMS spectrum while the latter by 1,3-dipolar cy-cloaddition reactions with various dipolarophiles that gave substituted isoxazoles, thus con-firming the nitrile oxide structure.

Studying the distribution and transport dynamics of cations in plants is crucial for understanding their response mechanisms to saline-alkali stress conditions. However, our current understanding of how restoration measures affect cation distribution and transport in plants is surprisingly limited. To address this gap, we conducted a split-plot experiment using Medicago sativa L. cv. “Zhongmu No. 1” to investigate the combined effects of biological and chemical restoration measures—with bio-fertilizer as the primary zone and flue gas desulfurization (FGD) gypsum with humic acid as the secondary zone—on soil properties, plant growth, and the content, distribution, and transport of cations in plants. The results revealed that different restoration strategies decreased soil alkalinity and enhanced plant growth. Significantly, bio-fertilizer exhibited positive effects on plant growth and yield. On the contrary, FGD gypsum with humic acid reduced the soil's pH level, exchangeable sodium percentage, and sodium adsorption ratio, while increasing the contents of K+, Ca2+, and Mg2+ in the soil. The triple combination of FGD gypsum and humic acid with bio-fertilizer reduced Na+ transport in M. sativa by enhancing the selective absorption of beneficial ions, such as K+, Ca2+, and Mg2+ in leaves, and by facilitating the transport of Ca2+ and Mg2+ from roots and stems to the leaves. Therefore, the application of FGD gypsum and humic acid combined with bio-fertilizer has the potential to decrease soil alkalinity and the proportions of water-soluble ions in the soil, ultimately enhancing the translocation of key ionic components to leaves. This, in turn, increases the salt tolerance of plants and promotes their growth. Our results offer new insights into the interactions among measures, soil, and plants in saline-alkali land restoration, providing practical solutions for the restoration of saline-alkali soil.

The combined effects of the thermal processing (i.e., sterilisation treatment) and the prior frozen storage time (3 or 6 months at –18 ºC) on the quality loss in canned Atlantic horse mackerel (Trachurus trachurus) were determined. Thus, the sterilisation step led to a remarkable (p&lt;0.05) formation in canned fish muscle of fluorescent compounds, free fatty acids (FFAs) and trimethylamine and to an increase of the L* and b* colour parameters; meantime, a decrease (p&lt;0.05) of the total ω3 FA/total ω6 FA ratio and the a* colour value were detected. The prior frozen storage period led to an increased (p&lt;0.05) lipid oxidation (peroxide, thiobarbituric acid reactive substance and fluorescent compound formation) and hydrolysis (FFA formation) development and to increased L* and b* colour values in the corresponding canned samples; additionally, a lower (p&lt;0.05) polyene index and phospholipid content were observed in canned fish previously subjected to frozen storage. In most indices, physico-chemical changes related to quality loss were found higher if the previous storage period was increased. According to the marked effects of the sterilisation step and the prior frozen storage period, optimisation of such processing conditions is recommended to maximise the quality of canned horse mackerel.

In response to global climate challenges and the increasing demand for energy, exploring renewable energy alternatives has become crucial. Bio-oils, derived from biomass pyrolysis, are emerging as potential replacements for fossil fuel-based liquid fuels. This paper shares findings from the Institute of Energy and Fuel Processing Technology on the quality of crude biomass pyrolysis bio-oil samples. These findings highlight their potential as motor liquid fuels. The article details the results of tests on the physicochemical properties of four distinct bio-oil samples. Additionally, it presents preliminary test results on the hydrodeoxygenation of bio-oils in a batch reactor. The production of homogeneous, stable mixtures using other fuel additives, such as diesel oil, rapeseed methyl ester (RME), and butanol, is also discussed.

Chitin/chitosan and collagen are two of the most important bioactive compounds with applications in the pharmaceutical, veterinary, nutraceutical, cosmetic, biomaterials, and other industries. When extracted from fish and shellfish non-edible parts, by-catches, and invasive species, their use contributes to a more sustainable and circular economy. The present article reviews the scientific knowledge and publication trends along the marine chitin/chitosan and collagen value-chains and assesses how researchers, industry players, and end-users can bridge the gap between scientific understanding and industrial applications. Overall, research on chitin/chitosan remains focused on the compound itself rather than its market applications. Still, chitin/chitosan use is expected to increase in food and biomedical applications, while that of collagen is expected to increase in biomedical, cosmetic, pharmaceutical, and nutritional applications. Sustainable practices, such as the reuse of waste materials, contribute to strengthen both value-chains; the identified weaknesses include the lack of studies considering market trends, social sustainability, and profitability, as well as insufficient examination of intellectual property rights. Government regulations, market demand, consumer preferences, technological advancements, environmental challenges, and legal frameworks play significant roles in shaping both value-chains. Addressing these factors is crucial for seizing opportunities, fostering sustainability, complying with regulations, and maintaining competitiveness in these constantly evolving value-chains.

Biomass as a whole offers a more diverse potential for valorisation than any other renew-able energy source. As one of the stages in the separation of bio-oil involves the liquid mixture of acetol and acetic acid, and as both components are particularly well suited for valorisation, a hybrid method has been developed for their separation with a high purity level through an approach combining liquid-liquid extraction and rectification. In order to design and simulate the flowsheet, the ChemCAD 7.0 simulation software has been used. Sensitive analyses have been carried out to investigate the influence of the different pa-rameters in the rectification columns such as the reflux ratio, the feed stage location, and the vapour/bottom molar flow ratio. The effect of different extractants and of their excess on the separation process as well as the possibility of regenerating the extractant has also been studied. Tri-n-octylamine has accordingly been selected as a separating agent which has been fully recycled. The end result for separating an initial 48/52 wt% ace-tol/acetic-acid liquid mixture has been acetol with a purity of 99.4 wt% and acetic acid with a purity of 100 wt%.

The effect of Localized Surface Plasmon (LSP) of 5 nm mean size Au particles deposited on TiO2 P25 was investigated during the photo-thermal water gas shift reaction (WGSR). The effects of CO concentration, excitation light flux and energy, and molecular oxygen addition during the reaction were investigated. The photocatalytic WGSR rate under light excitation with wavelengths extending from 320 to 1100 nm was found to be higher than the thermal reaction alone at the same temperature (85 oC). A ratio H2/CO2 of near unity was found at high concentrations of CO. Addition of molecular oxygen during the reaction resulted in a slight decrease of molecular hydrogen production while the rates of CO2 formation and that of CO consumption changed by one order of magnitude. More important, it was found that the WGSR rates were still high under only visible light excitation (600 - 700 nm). The results prove that Au LSP alone triggers this chemical reaction without the need to excite the semiconductor on which they are deposited.

Micro-arc oxidation (MAO) is an emerging technology employed to produce high hardness or anti-corrosion ceramic coatings on lightweight metals such Al, Ti, Mg and their respective alloys. However, under non-lubrication conditions, such coatings exhibit relatively high friction coeffi-cients. To enhance the friction reduction properties of the MAO coatings, we employed a one-step MAO process with varying concentrations of graphene oxide (GO) in an aluminate sys-tem electrolyte to create composite coatings on the surfaces of Ti-6Al-4V alloy. The effect of concentrations of GO particles on microstructure, composition, and wear behavior of the result-ing composite coatings was investigated. Measurements of the coating's thickness, hardness, and roughness have also been conducted. Ball-on-disk friction test under dry condition were carried out to reveal tribological behavior of the MAO coating. The addition of graphene oxide in the electrolyte reduces the friction coefficient, with the composite coating containing 5 g/L of GO particles displaying the most effective friction reduction. Moreover, coating thickness increases with higher GO concentration. This friction reduction can be attributed to the particles in the coating acting as lubricants during friction, while GO also reduces adhesive damage, shifting the wear mechanism from adhesive to abrasive.

Green synthesis offers a superior alternative to traditional methods for producing metal and metal oxide nanoparticles. This approach is not only benign and safe but also cost-effective, scalable, and straightforward, operating under ambient conditions. Notable metals and metal oxide nanoparticles, such as manganese oxides, iron oxides, silver, and gold, have been produced using various bio-reductants derived from plant extracts. These biological agents not only expedite the reduction process but also stabilize the nanoparticles, serving dual roles as reducing and capping agents. This review presents the green synthesis of nanoparticles (NPs) obtained from biogenic wastes and plant extracts. The green-synthesized nanostructured MnO2 are evaluated as a potential photocatalyst for water treatment and as an electrode material in lithium-ion batteries and supercapacitors. The green-derived iron oxide nanoparticles are examined as promising antioxidant, anti-inflammatory, and anti-diabetic agents. Additionally, this review discusses the green synthesis of precious metal nanoparticles, specifically silver (Ag NPs) and gold (Au NPs), highlighting their potential medical applications in areas like antiviral treatments and cancer therapy.

Tomato quality is intricately regulated by a combination of factors, including the presence of bioactive compounds referred to as secondary metabolites and various organoleptic characteristics. These attributes are notably influenced and harmonized by the specific growing conditions, with a particular emphasis on the type of fertilization employed. Traditionally, chemical fertilizers have been favoured in crop cultivation due to their cost-effectiveness and ability to accelerate crop growth. However, in pursuit of sustainable and intelligent agricultural practices, there is a growing need for alternative fertilizers. In this context, the present study aimed to assess the impact of fertilizers derived from waste materials, specifically sulphur bentonite and orange residue (referred to as SB), on tomato quality. This assessment extended to examining qualitative and quantitative alterations in aroma-related volatile compounds and the antioxidant systems of tomatoes, in comparison to the conventional use of fertilizers such as horse manure and NPK (nitrogen, phosphorus, and potassium). The results obtained revealed distinct effects of different fertilizers on tomato quality. Notably, parameters such as TPRO (total protein), TCARB (total carbohydrate), LIC (lycopene content), TCAR (total carotenoid content), total phenols, total flavonoids, and aroma profiling exhibited significantly superior values in the group treated with SB fertilizer. These findings strongly suggest that the novel fertilizer functioned as a bio-stimulant, enhancing the nutraceutical and sensory attributes of tomatoes, with a pronounced impact on the synthesis of secondary metabolites and the aroma profile of the fruits.

The reaction of pyridinium chlorochromate with furan to give enedione derivatives cannot be performed by using commercial PCC. Homemade and commercial PCC had different color and showed some differences in the XRD spectrum. XPS showed the presence of relevant amount of Cr(III) in the homemade reagent. DFT calculations showed that Cr(III) impurities in the reagent can catalyze the reaction with furan derivatives, if oxygen atom in the Cr(III) derivative attacks the furan ring, while it is reoxidized by PCC, through a migration of a chlorine atom.

This work demonstrates that microbial fuel cells (MFCs), optimized for energy recovery, can be used as an effective tool to detect the presence of antibiotics in water-based environments. MFCs directly convert chemical energy of organic matter in electrical energy thanks to electroactive biofilms. The efficiency of the conversion process can be significantly affected by the presence of contaminants acting as toxicants for the biofilm. In the present work, we demonstrate that MFCs can successfully detect the presence of antibiotic residues in water and water-based electrolytes associated to the food industry, especially using honey as a new and more complex electron donor. The effectiveness of MFCs to sense antibiotics is here demonstrated for tetracycline that was added to both water and water/honey electrolytes with a minimum concentration close to 3.5 μg⁄kg. MFCs not only efficiently detect the presence of tetracycline in both the electrolytes, but also recover the same performance after each cycle of exposure, showing to a be very robust and reliable technology for both biosensing and energy recovery.

This paper presents an investigation of the oxidation of Alloy X-750 containing 5% Fe in a simulated boiling water reactor (BWR) environment. To mimic the conditions in which the bare metal is exposed to the reactor water the samples were not pre-oxidized. The specimens were exposed for durations ranging from 2 to 840 hours, and the development of the oxide microstructure was mainly studied using electron microscopy. The results showed that the oxide scale consisted of blocky crystals of trevorite on top of a porous inner layer rich in Ni and Cr. After the longest exposure time, the trevorite crystals completely covered the specimen surface. The study further revealed that the speed at which the oxide grew and the metal dissolved both decreased with time. Additionally, the metal thinning process was found to be sub-parabolic. Given the significant variation in iron content in the X-750 specification, the influence of this element on the material's corrosion performance in BWR was examined by comparing the results from this investigation with those from previous work on material containing 8 wt% Fe. The study demonstrated that the oxide growth, metal dissolution and metal thinning were slower in the material with higher Fe content, indicating the importance of this element in limiting the degradation of Alloy X-750 in BWR environments.

In this study, a field experiment was conducted to evaluate the growth and yield responses of Sri Lankan lowland rice (Oryza sativa L.) with the application of beneficial Arbuscular mycorrhizal fungi (AMF) inoculum, and inter-cropping with highly mycorrhizal dependent vetiver grass (Chrysopogon zizanioides L.) under two different soil nutrient management systems (NMSs): conventional/chemical (CNMS) and organic (ONMS). The experiment was designed as a split plot with three blocks. Each CNMS and ONMS experiment included untreated control (T0), and three treatments—AMF inoculation (T1), vetiver intercropping (T2), and the combination of AMF and vetiver (T3). According to the results, colonization of rice roots with AMF was not affected significantly by the treatments and ranged from 0‒15.8%. The effect was very low or absent in the early stage and then higher in the later stages of the rice plant. Furthermore, plant growth was not significantly different between the two NMSs, although grain yield was significantly higher (P &lt; 0.05), with the order T1 (0.45 kg/m2) &gt;T2 (0.42 kg/m2) &gt;T3 (0.41 kg/m2) in CNMS and T2 (0.44 kg/m2) &gt;T1 (0.41 kg/m2) &gt;T3 (0.40 kg/m2), in ONMS than for the respective controls (T0), thus suggesting beneficial utilization of AMF and vetiver in the lowland rice farming system.

Antimicrobial peptides (AMPs) have emerged as a promising class of bioactive molecules with the potential to combat infections associated with medical implants and biomaterials. This review article aims to provide a comprehensive analysis of the role of antimicrobial peptides in medical implants and biomaterials, along with their diverse clinical applications. The incorporation of AMPs into various medical implants and biomaterials has shown immense potential in mitigating biofilm formation and preventing implant-related infections. We review the latest advancements in biomedical sciences and discuss the AMPs that were immobilized successfully to enhance their efficacy and stability within the implant environment. We also highlight successful examples of AMP coatings for the treatment of surgical site infections (SSIs), Contact lenses, Dental Applications, AMP-Incorporated Bone Grafts, Urinary tract infections (UTIs), Medical Implants, etc. Additionally, we discuss the potential challenges and prospects of AMPs in medical implants, such as effectiveness, instability and implant-related complications. We also discuss strategies that can be employed to overcome the limitations of AMP-coated biomaterials for prolonged longevity in clinical settings.

Coronary artery disease is the most prevalent cardiovascular disease, claiming millions of lives annually around the world. The current treatment includes surgically inserting a tubular construct called as a stent inside arteries to restore blood flow. However, due to lack of patient-specific design, the commercial products cannot be used with different vessel anatomies. In this review, we have summarized the drawbacks in existing commercial metal stents which face problems of restenosis and inflammatory responses, owing to the development of neointimal hyperplasia. Further, we have highlighted the fabrication of stents using biodegradable polymers, which can circumvent most of the existing limitations. In this regard, we elaborated on utilization of new fabrication methodologies based on additive manufacturing such as three-dimensional printing to design patient-specific stents. Finally, we have discussed on the functionalization of these stent surfaces with suitable bioactive molecules which can prove to enhance their properties in preventing thrombosis and better healing of injured blood vessel lining.

This paper presents the concept of a novel adaptable sensing solution currently being developed under the EU Commission founded PHOTONGATE project. This concept will allow to quantify multiple analytes of the same or different nature (chemicals, metals, bacteria, etc.) in a single test with levels of sensitivity and selectivity at/or over those offered by current solutions. PHOTONGATE relies on two core technologies: a bio-chemical technology (molecular gates) which will confer the specificity and, therefore, the capability to be adaptable to the analyte of interest, and which combined with porous substrates will increase the sensitivity, and a photonic technology based on Local Surface Plasmonic Resonance (LSPR) structures serves as transducer for light interaction. Both technologies are in the micron range, facilitating the integration of multiple sensors within a small area (mm²). The concept will be developed for its application in health diagnosis and food safety sectors. It is thought as an easy-to-use modular concept, which will consist of the sensing module, mainly of a microfluidics cartridge that will house the photonic sensor, and a platform for fluidic handling, optical interrogation, and signal processing. The platform will include a new optical concept, fully Europe Union Made, avoiding optical fibers and expensive optical components.

Textile industry is one of the major industries responsible for environmental pollution globally. This is mainly due to the use of synthetic dyes, toxic ingredients and solvents for dy-ing/treatments/protocols of textiles. Replacement of those non ecofriendly ingredients would be a very challenging target to develop novel sustainable textile dying strategies. Using biobased and bioactive pigments, antibacterial ingredients and especially natural solvents are recently pointed out as substances to included in the related formulations. In this study the dyeing ability of the crude gel prodigiosin produced by non-pathogenic bacteria Serratia plymuthica as a natural pigment was investigated on various multifiber fabrics at different condition (temperature and pH) and by using salts (NaOH and Na2S2O4) and alternative mordants (a conventional: FeSO4 and a new bio-mordant: L-Cysteine (L-Cys)) in the recipes with different compositions and especially replacing of organic solvent with a new type of gel-based Choline chloride (ChCl) : Lactic acid (LA) (1 : 2) deep eutectic solvents (DES) as a dyeing medium. For determination of the dying process performances, the color strength (K/S value) of dyed fabric and the dyeing equalization (dE) parameters were evaluated. The fastness properties of the dyed fabrics which displayed as a higher K/S value and good dE were evaluated. The nylon fabrics dyed with 3.0% owf L-Cys at pH = 8.3 improved the color fastness to washing, while the gel-based ChCl : LA (1 : 2) DES dyebath provided a better color fastness to light. Moreover, the nylon fabrics under these conditions exhibited remarkable anti-microbial activity against Staphylococcus aureus (S. aureus) and Pseudomonas aeruginosa (P. aeruginosa). As conclusion, the use of the crude gel prodigiosin pigment revealed an advantageous ability to dye the textile materials, responding to consumers' demand for more ecological and sustainable products. Furthermore, the natural reducing agent L-Cys, never tested before as a bio-mordant, and the use of gel-based DES as a dyeing medium demonstrated enhanced colorimetric and antibacterial properties on dyed nylon with crude gel prodigiosin pigment.

Based on the Flashing Ratchet Potential (FRP) and Electro-Spectroscopy detection techniques, a new detection method was experimentally examined. This method allows the detection of sub-micro particles in the human exhaled air such as viral particles and other biological agents. The detection signal created by this method is carried out by electron current buildup forming an Electric Current-Spectrum (ECS) distinguishing the contents of the exhaled air samples. The detection method was developed based on FRP and a beam of free charges passing through the electrodes of the FRP. The ECS is characterized by low-energy free charges interacting with the medium through which they pass, where numerous free charges are scattered (delayed) as a result of these interactions. The resulting ECS is characterized by FRP's capacity to drift back the delayed free charges to their original starting positions. By comparing the ECS of two exhale air samples, this new technology can be utilized to identify the presence of viral and microorganisms’ particles. The time-escalating ECS difference quickly indicates the presence of such particles. Moreover, the FRP's optimal operating settings was experimentally defined, in addition to the experimental evaluation of its functionality to confirm the FRP's promising sensing capabilities, which were statistically examined several times to ensure the reproducibility of the results.

The optical complexity of coastal waters is mostly caused by the water discharged from land carrying optical components (such as dissolved and particulate matter) into coastal bays and estuaries, and increasing the attenuation of light. This paper aims to investigate the links between in-water optical properties in four Swedish bays (from the northern Baltic proper up to the Bothnian bay) and the land use and land cover (LULC) and the hydrology in the respective catchment of each bay. The optical properties were measured in situ over the last two decades by various research and monitoring groups while the LULC in each bay was classified using the Copernicus Land Monitoring Service based on Landsat 8 and Sentinel-3 data. The absorption coefficient of coloured dissolve organic matter at 440 nm, aCDOM (440), and its spectral slope factor, SCDOM, were mostly correlated to natural land cover classes (Wetland, Meadow) acting as sources of CDOM, while Agricultural and Urban classes seem to act as sinks. The Agricultural class was also found to be a sink for suspended particulate organic matter (SPOM) whilst Coniferous and Mixed Forests as well as Meadows acted as a sources. SPOM seems to mostly originate from Natural classes, possibly due to the release of pollen and other organic matter. Overall, the methods applied here allow for a better understanding of effects of land used and land cover on the bio-optical properties, and thus coastal water quality, on a macroscopic scale.

This study presents a comprehensive investigation of the formation, composition, and behaviour of oxide layers during the high-temperature oxidation of four different steel alloys (16Mo3, 13Cr, T24 and P91) at a uniform temperature of 650 °C. The research combines CALPHAD (CALculation of PHAse Diagrams) calculations, thermogravimetric analysis (TGA) and advanced microscopy techniques, including scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), to elucidate the complex mechanisms controlling oxidation kinetics and oxide layer development. CALPHAD calculations were used to determine the thermodynamically stable phases for each steel type at 650 °C. The results showed different phase compositions, highlighting the importance of steel composition in the formation of oxide layers. Each steel grade exhibited different kinetics, with 16Mo3 steel showing the highest oxidation rate, followed by 13Cr, T24 and P91. This variability highlights the role of steel composition, particularly chromium content, in determining oxidation behaviour. These results have significant implications for temporary overheating in industrial applications and contribute to a deeper understanding of oxidation processes in steels.

The work presents a mathematical model of a thermogravimetric curve for the growth and simultaneous sublimation of scale on a metal or alloy surface. Reduction of the reaction area as a result of the formation of oxides of alloying elements (for obtaining the basic oxide) is considered for the alloy. For metals, the case where this area is increased as a result of powder metal crushing is also considered. The equations that were obtained are employed to explain the kinetic curves of the mass change of the samples.

Series of bifunctional catalysts, MoS2/Al2O3(70 wt.%)-zeolite (30 wt.%) (zeolite – ZSM-5, ZSM-12, ZSM-22 and silica aluminophosphate SAPO-11), were synthesized for hydroconversion of methyl palmitate (10 wt.% in dodecane) in a trickle-bed reactor. Mo loading was about 7 wt.%. Catalyst and supports were characterized by different physical-chemical methods (HRTEM-EDX, SEM-EDX, XRD, N2 physisorption, FTIR spectroscopy). Hydroprocessing was performed at temperature of 250-350°C, hydrogen pressure 3.0-5.0 MPa, liquid hourly space velocity (LHSV) 36 h-1, H2/feed ratio – 600 Nm3/m3. Complete conversion of oxygen-containing compounds was achieved at temperature 310°C in the presence of MoS2/Al2O3-zeolite catalysts, the selectivity for the conversion of methyl palmitate via the ‘direct’ hydrodeoxygenation (HDO) route was over 85%. The yield of iso-alkanes gradually increases in order: MoS2/Al2O3 &lt; MoS2/Al2O3-ZSM-12 &lt; MoS2/Al2O3-ZSM-5 &lt; MoS2/Al2O3-SAPO-11 &lt; MoS2/Al2O3-ZSM-22. The sample MoS2/Al2O3-ZSM-22 demonstrated the highest yield of iso-alkanes (40%). Hydroisomerization activity of the catalysts was in a good correlation with concentration of Brønsted acid sites of synthesized supports.