A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

The R23Cu7Mg4 (R = Ca, Eu) intermetallics, studied by single crystal X-ray diffraction, were found to be isostructural with the Yb23Cu7Mg4 prototype (hP68, k4h2fca, space group P63/mmc), forming a small group inside the bigger 23:7:4 family, otherwise adopting the hP68-Pr23Ir7Mg4 crystal structure. The observed structural peculiarity is connected with the divalent character of the R component and with a noticeable volume contraction, resulting in a clear clustering of title compounds inside the whole 23:7:4 family. The occurrence of fragments typical of similar compounds, particularly Cu-centered trigonal prisms and Mg-centered core-shell polyicosahedral clusters with R at vertices, induced the search of significant structural relationships. In this work, a description of the hexagonal crystal structure of the studied compounds is proposed as a linear intergrowth along the c-direction of the two types of slabs R10CuMg3 (parent type: hP28-kh2ca, SG 194) and R13Cu6Mg (parent type: hR60-b6a2, SG 160). The ratio of these slabs in the studied structure is 2:2 per unit cell, corresponding to the simple equation 2XR10CuMg3 + 2XR13Cu6Mg = 2XR23Cu7Mg4. This description assimilates the studied compounds to the (Ca,Eu,Yb)4CuMg ones, where the same slabs (of p3m1 layer symmetry) are stacked in a different way/ratio, and constitutes a further step towards a structural generalization of R-rich ternary intermetallics.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

Thin twin-roll cast strips from a model Al-Cu-Mg-Li-Zr alloy with a small addition of Sc were prepared. A combination of a fast solidification rate and a favorable effect of Sc microalloying impacts the size and distribution of primary phase particles and the dimension of eutectic cells. Small interdendritic spacing in the range of 10-15 um enables substitution of the initial long-term homogenization annealing by a two-step annealing at 300 and 450 °C and a short solution treatment at 530 °C before quenching and the final age-hardening procedure. A dense dispersion of small Al3(Sc,Zr) precipitates intensively inhibiting recrystallization forms during this treatment. Further refining and fragmentation of the structure were performed using constrained groove pressing before the solution treatment. Small pre-straining of quenched specimens and subsequent age-hardening simulating T8 temper were used to promote the formation of a homogeneous distribution of strengthening particles and to suppress preferential heterogeneous precipitation on subgrain and grain boundaries. Microstructural features and microhardness evolution during annealing were critically examined and confronted with microstructural characteristics observed on reference mold cast alloy or alloys without Sc alloying. The proposed treatment represents a model near net shape procedure for manufacturing thicker sheets for the aerospace industry.

The rapidly evolving field of additive manufacturing requires a periodic assessment of the progress made in understanding the properties of metallic components. Although extensive research has been undertaken by many investigators, the data on properties such as hardness from individual publications are often fragmented. When these published data are critically reviewed, several important insights that cannot be obtained from individual papers become apparent. We examine the role of cooling rate, microstructure, alloy composition, and post process heat treatment on the hardness of additively manufactured components. Hardness data for steels and aluminum alloys processed by additive manufacturing and welding are compared to understand the relative roles of manufacturing processes. Furthermore, the findings are useful to determine if a target hardness is easily attainable either by adjusting AM process variables or through appropriate alloy selection.

Ongoing investigations have highlighted that MIM of Mg shows high potential for mass production of small lightweight components as well as of degradable implants with complex geometry. However, prior research activities have shown that Mg reacts sensitively to atmosphere impurities like oxygen and specific thermal decomposition products of the used backbone polymers. Polyethylene based polymers reveal a negative influence on sintering of Mg while polypropylene based polymers behave uncritically. This work is highlighting that when hydrogen instead of argon atmosphere is used during sintering, the negative influence caused by carbon residuals at the particle boundaries can be prevented. Mg-0.9Ca elongation increased with a slight decrease in UTS revealing a strengthening effect of the carbon residuals at the particle boundaries. For pure Mg UTS could be increased from 7 MPa up to 80 MPa with elongation of 6% showing the positive effect of hydrogen on the sintering of Mg.

Sustainable development of our society demands recycling of metallic wastes which may contain a variety of metallic impurities. Thus, it is desirable to develop a ‘universal’ structure, such as an amorphous alloy tolerating high concentrations of metallic pollutants. We performed ab initio molecular dynamics simulations to manufacture a novel multicomponent amorphous alloy of twenty elements (20e-HEAA). Analysis reveals both topological and chemical compositional short-range ordering in the obtained 20e-HEAA and formation of B-B clusters. Electronic structure calculations reveal the metallic nature of the amorphous alloy with its Fermi level falling in a valley in the density of states. Moreover, the Zn 3d and Cd 4d electrons exhibit a localized nature and thus, should be excluded from the valence electron concentration (VEC) analysis in the study of high-entropy alloys. The information obtained here is helpful to get insight into multicomponent high entropy materials, especially multicomponent high-entropy amorphous alloys as potential circular metals.

Magnesium (Mg) alloy is a widely used lightweight metal structural material due to its high specific strength and stiffness, excellent damping performance, and recyclability. Wrought Mg alloys are widely favored in fields such as aerospace, transportation, and biomedical stents. However, most wrought Mg alloys with a hexagonal close-packed (HCP) crystal structure lack sufficient independent slip systems to meet the von Mises criterion for uniform plastic deformation at room temperature. This can result in the formation of strong basal texture during plastic deformation and poor room temperature plastic forming ability. Improving the room temperature forming performance is a crucial challenge that must be addressed to broaden the application of Mg alloy sheets. Our research group has comprehensively summarized significant work and latest research progress in improving the room temperature forming of Mg alloy sheets via extrusion technology in recent years. Specifically, we have developed a new type of asymmetric extrusion technology that combines material structure evolution, mechanical property, and forming behavior analysis. We have elucidated the extrusion process characteristics, texture control mechanism, and forming properties of Mg alloy sheets through plastic deformation mechanisms, mold design, and finite element numerical simulation. Our findings provide a novel extrusion technology for the fabrication of highly formable Mg alloy sheets, which can be utilized in various applications.

The effect of Mg particles on PLA's thermal, chemical, physical, and mechanical properties has been studied. The thermal and physical properties have been studied by differential scanning calorimetry, analysing the stability of the α and α’-crystals of the PLA. A colloidal route was used to introduce Mg particles inside the PLA matrix, ensuring a good dispersion of the particles. Materials with Mg contents from 0 to 10 wt.% have been prepared, with additions of polyethyleneimine (PEI) and polyethylene glycol (PEG). Fourier Transform Infrared Spectroscopy has been used to confirm the influence of Mg, PEI, and PEG on PLA properties. The mechanical properties have been measured with a universal tensile test machine on printed filaments via Fused Filament Fabrication (FFF), which were naturally aged to stable conditions. Filaments with and without a notch were studied to obtain the materials' tensile strength, elastic modulus, and fracture toughness. Different analytical models to explain the results of the PLA-Mg were studied, in which the interface strength of the PLA-Mg composites was calculated.

This study investigated defect formation and strain distribution in high Mg content Al-Mg alloys during normal rolling and cross-rolling processes. The finite element analysis (FEA) revealed the presence of wave defects and strain localization-induced zipper cracks in normal cold rolling, which were confirmed by experimental results. The concentration of shear strain played a significant role in crack formation and propagation. However, the influence of wave defects was minimal in the cross-rolling process, which exhibited a relatively uniform strain distribution. Nonetheless, strain concentration at the edge and center regions led to the formation of zipper cracks and edge cracks, with more pronounced propagation observed in the experiments compared to FEA predictions. Furthermore, texture evolution was found to be a crucial factor affecting crack propagation, particularly with the development of the Goss texture component which is observed by electron backscattered diffraction analysis at bending points. The Goss texture hindered crack propagation, while the Brass texture allowed cracks to pass through. This phenomenon was consistent with both FEA and experimental observations. To mitigate edge crack formation and propagation, potential strategies involve promoting the formation of the Goss texture at the edge through alloy and process conditions, as well as implementing intermediate annealing to alleviate stress accumulation. These measures can enhance the overall quality and reliability of Al-Mg alloys during cross-rolling processes. In summary, understanding the mechanisms of defect formation and strain distribution in Al-Mg alloys during rolling processes is crucial for optimizing their mechanical properties. The findings of this study provide insights into the challenges associated with wave defects, strain localization, and crack propagation. Future research and optimization efforts should focus on implementing strategies to minimize defects and improve the overall quality of Al-Mg alloys in industrial applications.

Bacterial internalization is a strategy that non-intracellular microorganisms use to escape the host immune system and survive inside the human body. Among bacteria species, Staphylococcus aureus showed ability to interact and infect osteoblasts causing osteomyelitis as well as bone and joint infection, while also becoming increasingly resistant to antibiotic therapy and a reservoir of bacteria that can make the infection difficult to cure. Despite being a serious issue in orthopedic surgery, little is known about the mechanisms that allow bacteria to enter and survive inside the osteoblasts, also due to the lack of consistent experimental models. In this review, we describe the current knowledge about S. aureus internalization mechanisms and various aspects of the interaction between bacteria and osteoblasts (e.g. best experimental conditions, bacteria-induced damages and immune system response), focusing on studies performed using the MG-63 osteoblastic cell line, so far the best model for the study of this phenomenon.

Biomedical devices made from high-modulus and hardness materials play a critical role in enhancing the quality of life for individuals with bone-related ailments. While these materials have been successfully used in orthopedic applications, concerns including stress-shielding have necessitated the exploration of alternative solutions. An ideal biomedical implant requires a delicate balance of mechanical performance, corrosion resistance, tissue biocompatibility, and other properties such as tribological performance and osseointegration. This review explores the suitability of biodegradable magnesium (Mg) alloys as a promising material for biomedical implants. It delves into the essential properties of biomedical implants, emphasizing the importance of matching mechanical characteristics with human bone properties to mitigate stress shielding. The corrosion properties of implant materials are discussed, highlighting the need for controlled degradation to ensure the safety and longevity of implants. The focus then shifts to the potential of magnesium alloys as biomedical implants, examining their benefits, limitations, and the challenges associated with their high degradation rates and less-than-satisfactory mechanical properties. Alloying with elements such as aluminum, zinc, and others is explored to improve magnesium alloys' mechanical performance and corrosion resistance. Furthermore, this review discusses surface modification techniques, including chemical conversion coatings and biomimetic deposition, as effective strategies to enhance the corrosion resistance and biocompatibility of magnesium and its alloys. These modifications offer opportunities to improve the long-term performance of magnesium-based biomedical implants. This paper provides a comprehensive overview of the properties, challenges, and potential solutions associated with biodegradable magnesium alloys as a promising material for biomedical implants. It underscores the importance of addressing issues related to mechanical performance, corrosion resistance, and biocompatibility to advance the development of safe and effective biomedical implant materials.

Within the task of replacing bronze journal bearings with aluminum the processes taking part on friction surface of high-alloyed aluminum alloys working with steel are investigated. The surface and subsurface layer of experimental aluminum bearings were studied before and after tribological tests by scanning electron microscopy including energy-dispersive analysis. Both structural and composition changes in surface layer are shown. It has been revealed that secondary structures are formed on the surface during friction process and include all the chemical elements of the tribosystem which is a consequence of its self-organization. The interaction behavior of some chemical elements of tribological system is discussed.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

In the article, we are trying to find a general law that describes the physical properties of a complex compound through the same physical properties of compound elements. For metal alloys operated under extreme conditions - neutron and proton irradiations and thermal heating, the mechanical properties of these alloys and their elements have been studied. It turned out that the ultimate tensile strength of tantalum alloys used in the design of space reactors can be expressed in terms of the weighted sum of the ultimate tensile strengths of its elements in the range of neutron doses: (0 - 0.96) displacement per atom (dpa) for Ta–10W alloy and (1.4 - 1.7) dpa for T–111 alloy with a neutron energy of more than 0.1 MeV. For tungsten binary alloys used in the design of fusion reactors, the Vickers hardness can also be expressed in terms of the weighted sum of the Vickers hardnesses of the alloy elements in the range of proton irradiation doses: (0 - 0.05) dpa for W-1%Re alloy, (0.05 - 0.2) dpa for W-3%Re alloy and (0.05 - 1) dpa for W-1%Ta with a proton energy of 1 MeV.

In this study, an extensive data set was based on existing literature records in order to enable the suitability of several predictive models, from Multiple Linear Regression (MLR) to Neural Networks (NN). The main objective was to, through regression analyses, generate model computations to correlate tensile properties (UTS- Ultimate Tensile Strength, YTS – Yield Tensile Strength and EF – Elongation-to-Fracture) to a given alloy composition and microstructural spacing. This investigation led to positive results, as the highest accuracies of the trained modules (in 80% of the database) were found to be above ~82% (UTS and EF) and a maximum of ~98% (YTS), when analyzing the results to a test data set. Later, these models were used to define trends for possible next solder alloy commercial compositions. Overall, using the standard model’s setup, the Random Forest and Decision Tree models showed the highest accuracy results, with 0.958 for YTS as opposed to 0.907 for MLR. Moreover, Multilayer Perceptron (MLP)-optimized models yielded the best results for each variable, with the highest increases in accuracy associated with the YTS and EF. The present contribution might imply an important milestone towards alloy design research based on data science guidelines to unlock the full potential of former experiments and their extensive set of results.

There is an increase towards reducing the weight of structures through the use of aluminium alloys in different industries like aerospace, automotive, etc. This growing interest would lead towards using dissimilar aluminium alloys which would require welding. TIG and friction stir welding are the well-known techniques that are currently suitable for joining dissimilar aluminium alloys. The welding of dissimilar alloys has its own dynamics which impact on the quality of the weld. This then suggests that there should be a process which can be used to improve the dissimilar alloys welds post their production. Friction stir processing is viewed as one of the techniques that could be used to improve the mechanical properties of the material. This paper reports on the status and the advancement of FSW, TIG and FSP technique. It further looks at the variation use of FSP on TIG and FSW welded joints with the purpose of identifying the knowledge gap.

The type of implant at the fracture site has effects not only from biological perspective but also from mechanical perspective in fracture healing. Biodegradable implants such as magnesium (Mg) based alloys have shown faster secondary bone healing properties as compared to bioinert implants such as titanium (Ti). The general reasoning behind this is the benefit of Mg from biocompatibility perspectives. We study the effect of Ti and Mg as base materials for implants with their different mechanical properties. The focus of our work is on the displacements at the fracture site of the tibia and their influence on the stimulus for bone healing. We have found that in comparison to Ti, Mg implants have minimal stress shielding problem, only which led to better mechanical stimulus at the fracture site.

The European Green Deal poses a two-pronged challenge for the automotive industry: migrating to solutions based in light structures, requiring light weight concepts and light materials, while at the same time avoiding dependence towards the importation of these advanced materials. Aluminium alloys are lightweight and cost-effective materials that can successfully cover the requirements of many structural applications, however their production requires from bauxite and other Critical Raw Materials (CRM), such as Si and Mg. Aluminium alloys are fully recyclable, but scrap is usually contaminated and its use is related to an increment of impurities, tramp element and undesired inclusions. Traditionally, the use of secondary alloys has been restricted to low performance applications. The present work analyses the effect that the use of scrap has in the quantity of inclusions present in the alloy and in other properties relevant for the material processing. The study was carried out for common alloys belonging to 3 of the most common aluminium processes used in the car manufacturing industry: High Pressure Die Casting (HPDC) (EN AC-43500), extrusion (6063) and sheet metal forming (5754 and 6181). Reference alloy were mixed with different level of scrap (0, 20, 40, 60, 80 and 100%) trying to keep the chemical composition as unaffected as possible. The inclusions level of the alloy was characterized with the Prefil Foot-printer® test. In addition, the obtained materials, after being cast in an open mould, were subjected to metallographic characterization. Relevant properties to assess the formability quality of the alloys for the corresponding transforming process, were obtained: flowability test for HPDC alloy and high temperature compression for extrusion alloys. The results obtained suggest that the number of inclusions present in the melt highly increase with the amount of scrap used to produce the alloy. These inclusions are also related with an important lost of flowability, but do not have a noticeable impact on microstructure.

Adding zinc (II) and formate anions improves the thermal phase-stability of alpha-FAPbI3 materials and the spin-coated thin films of such doped FAPbI¬3 show an increased emission lifetime of up to 3.7 microsecond on quartz. This work investigates the effects of zinc and formate on the stability and time resolved photoluminescence of FAPbI3 perovskites for solar cell applications. Perovskite samples with varying concentrations of zinc and formate were made by incorporating different amounts of zinc formate and zinc iodide and characterized with XRD. Doping levels of 1.7% Zn(II) and 1.0% formate (relative to Pb) seem optimal. The thermal stability of the perovskite powders and thin films were assessed. XRD was virtually unchanged after 6 months. The time-resolved photo-luminescence spectroscopy of the doped spin-coated perovskite samples is reported. The results show that synergy between an anionic and a cationic dopant can take place, making the perovskite thermally more stable with a longer charge carrier lifetime.

The present work reports on the calculated electronic and magnetic structure of the binary Co-Ga system at high Co content. β-CoGa adopts a simple cubic CsCl type structure. Well-ordered CoGa does not exhibit collective magnetism but is a paramagnetic, metallic compound. Neither Co nor Ga deficiency induces magnetic order, however, ferromagnetism is observed for Co-Ga anti-site disorder. The magnetic moment per cell increases up to about 1.2 μB in the completely disordered body centered cubic structure. With increasing Co content, Co1+xGa1−x maintains the CsCl type structure and becomes ferromagnetic. Most important, a discontinuity of the magnetic order with composition is observed at about 10% excess Co, where a change from a low magnetic moment state to a high moment state is observed. This is accompanied by a change in the electronic structure and transport properties. The discontinuity is forced by the increasing exchange splitting related to the localized moment of the additional Co atoms that replace Ga. Subsequently, the magnetic moment increases continuously up to 2.5 μB for x=0.6. For x≳0.6, the structure changes to face centered cubic with random site occupation and the magnetic moment further increases. Above the magnetic discontinuity, the Curie temperature increases linearly with the Co content from the onset of ferromagnetism, until it reaches its maximum in pure Co.

Light alloys machining is a widely implemented process that have usually used in presence of cutting fluids to reduce the wear impact and increase tool life. However, current environmental protection policies require their elimination in order to improve process sustainability. This fact forces to work under aggressive cutting conditions, producing adhesion wear that affects the integrity of the part surface. This study describes cutting tool wear mechanisms in machining of UNS A92024 samples under dry cutting conditions. EDS analysis showed the different composition of the adhered layers, while roughness was also positively affected by the change of the cutting geometry produced in the tool.

In this work, plastic deformation was locally introduced at room temperature by nanoindentation on a γ-TiAl based alloy. Comprehensive analyzes of microstructures were performed before and after deformation. In particular, the Burgers vectors, the line directions and the mechanical twinning systems were studied via accurate electron channeling contrast imaging. Accommodation of the deformation are reported and a scenario is proposed. All features help to explain the poor ductility of the TiAl based alloys at room temperature.

In this study composite with alternate layers of 5056 and 1580 alloys was manufactured by wire arc additive manufacturing technology. It is shown that increased strength characteristics of composite material can be obtained due to deformation treatment by high-pressure torsion (HPT) technique. The microstructure and mechanical properties of the HPT-processed material in different structural states were investigated. The HPT-processed material exhibits high value of ultimate tensile strength (~ 770 MPa) but low ductility. Short-term annealing at 250 oС and additional deformation by HPT to 0.25 of revolution at room temperature resulted in a slight decrease in material’s strength to ~ 700 MPa but provided ductility ∼ 9%. Physical mechanisms to improve plasticity in correlation with microstructure evolution is discussed.

Bulk composition, mineralogy and microchemistry of various fractions of the filling of the Crater No. 4 at Emmerting were investigated. Here we present mainly the fine fractions, which, in contrast to pebbles larger than ca. 4 cm, are relatively poor in material affected by melting. A 0.1 mm long meteorite fragment without ablation features was found, and remelted fragments of the same body have been identified. The projectile was dominated by enstatite, also containing forsterite, basic plagioclase, Ni-rich pyrrhotite and troilite, kamacite, silica, and probably merrillite. The molten fragments contain porous Mg-rich glass (indicating temperature > 1500 °C), minor Fe oxides, and occasionally uncommon Ni-rich minerals. The bulk composition and electron microprobe show that the amount of meteoritic material is low (<< 1 %), and it is not unequivocally manifested even in platinum-group elements abundances and osmium isotope ratios (the latter, however, were only measured in two samples). This can be explained by dilution of the filling by particles brought after the crater formation, and by probably achondritic composition of the projectile. Relatively large hollow spheroid Fe oxide particles were observed in thin sections from the magnetic fraction. A Mn oxide hollow spherule has also been found. In magnetically separated filling from the nearby Crater No. 5, bulk chemical composition points to contamination with several metals and metalloids probably due to influence of recent alluvial sediments. Therefore, the extent of meteoritic contamination in this crater may be even smaller.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

The manufacturing parameters influence the properties of thermo-mechanically processed met-als such as Mg alloys. This paper presents how the mechanical properties, the microstructure and the degradation rate of extruded Mn-containing Mg-Gd-alloys can be modified. Gd as repre-sented REE-element is particularly interesting due to the influence on the texture development in Mg and therefore studied as a base alloy system. The contents of Gd were investigated be-tween 2 to 9 wt.% with Mn-addition of 0.5 and 1.0 wt.%. The grain sizes and the corresponding textures were modified by the extrusion parameters and the alloy content. It was shown that modification by Mn can decrease the grain size, but increase the degree of recrystallization and decrease the degradation rate in the biological medium compared to the binary Mg-Gd system from previous studies. The results suggest that the binary Mg-Gd system can be produced more efficiently by adding Mn and that the resulting properties are more robust.

The effect of retrogression re-aging treatment (RRA) on corrosion behavior of 7055 Al-Zn-Mg alloy were studied. Results provides the corrosion resistance could be greatly improved by RRA. After the RRA treatment, the isolated precipitates occurred on grain boundaries (GBs) and the low angle grain boundaries (LAGBs) presented a larger fraction compared to the single-stage peaking aging. The samples after RRA treatment also show better corrosion resistance than the single-stage peak aging. The results of electrochemical impedance spectroscopy (EIS) show that impedance spectrum is consisted of semi-infinite layer diffusion impedance and stagnant Weber impedance. The semi-infinite layer diffusion impedance corresponded a limited retention layer on the electrode surface. In corrosion process, Weber impedance corresponded to stagnant layer of corrosion products generated by the anode branches. The RRA sample has the high Rf and low Cf, Cp values, and the corrosion current density of the RRA samples is ten times less than the single-stage peak aging samples with the 10% hardness losing.

The effect of defects and microstructure on mechanical properties of Ti-6Al-4V welds produced by tungsten inert gas welding, plasma arc welding, electron beam welding and laser beam welding was studied in the present work. The mechanical properties of the different weld types have been evaluated with respect to micro hardness, yield strength, ultimate tensile strength, ductility and fatigue at room temperature and at elevated temperature. Metallographic investigation was carried out to characterize the microstructures of different weld types and fractographic investigation to relate the effect of defects on fatigue performance. Electron and laser beam welding produced welds with finer microstructure, higher tensile ductility and better fatigue performance than tungsten inert gas welding and plasma arc welding. Large pores and pores located close to the specimen surface were found to be most detrimental to fatigue life.

Group IV alloys of GeSn have been extensively investigated as a competing material alternative in short-wave to mid-infrared photodetectors (PDs). The relatively large defect densities present in GeSn alloys are the major challenge in developing practical devices, owing to the low-temperature growth and lattice mismatch with Si or Ge substrates. In this paper, we comprehensively analyze the impact of defects on the performance of GeSn p-i-n homojunction PDs. We first present our theoretical models to calculate various contributing components of the dark current including minority carrier diffusion in p- and n-regions, carrier generation-recombination in the active intrinsic region, as well as the tunneling effect. We then analyze the effect of defect density in the GeSn active region on carrier mobilities, scattering times and the dark current. A higher defect density increases the dark current, resulting in reduction in detectivity of GeSn p-i-n PDs. In addition, at low Sn concentrations, defect-related dark current density is dominant, while the generation dark current becomes dominant at a higher Sn content. These results point to the importance of minimizing defect densities in the GeSn material growth and device processing, particularly for higher Sn compositions necessary to expand the cutoff wavelength to mid- and long-wave infrared regime. The study provides more of realistic expectations and guidelines for evaluating GeSn p-i-n PDs as a competitor to the III-V and II-VI-based infrared PDs currently on the commercial market.

Nickel-base superalloys like VDM 780 may possess a high content of Cr and Co. This influences solution energies of phase-forming elements like Al and Ta (γ′-phase), Nb (γ′′- and δ-phase), and Ti (η-phase). We perform density functional theory studies of a nickel matrix at 0 K with high concentrations of either Co and Cr and calculate the influence of these elements on solution energies. In the case of Co, the solution energy can be predicted well by the nearest-neighbor interaction in the Co-rich matrix. For Cr, the effect is more complicated because Cr has a larger ionic radius and changes the magnetic state of the material. The effect of a Cr-rich matrix on the energy of Co is dominated by magnetic effects, interactions with the other elements by elastic deformation of the lattice.

The concept of green energy is now at the forefront of development discourse, with the United Nations Sustainable Development Goals (SDGs) 7, 11, and 12 all aimed at promoting green energy consumption to combat the three planetary crises: climate change, biodiversity loss, and pollution. Similarly, issues regarding Africa’s natural resource curse have caused a stir in the growth and development literature for some time now and there is no sign that it will die out. This study, the first of its kind, simultaneously assesses the impact of green energy consumption and Africa’s natural resources rents on economic growth by applying the Feasible Generalized Least Square (FGLS) estimator and the dynamic panel models of the Pooled Mean Group (PMG) and Mean Group (MG) estimators on data from 1990 to 2020 for 24 selected African countries. The results show that green energy consumption has a short-run growth-limiting effect and a long-run growth-enhancing effect in Africa. The study also found evidence of the natural resource curse phenomenon in Africa. The study, therefore, calls for the advancement and usage of green energy for both domestic and industrial production in Africa. The study further calls for a revamp in the global tax policy to curb illicit financial activities and strengthening institutional quality for transparency and accountability in the entire value chain of natural resource management in Africa.

The mechanism underlying microbiologically induced carbonate precipitation have not been thoroughly characterized, although numerous scholars and experts have specifically investigated questions regarding minerals induced by bacteria. The study of the precipitation of carbonate minerals induced by halophilic bacteria has aroused wide concern. The present study aimed to investigate the characterization and process of biomineralization in high salt systems by a halophilic bacterium, Chromohalobacter israelensis strain LD532 (GenBank: KX766026), which was isolated from the Yinjiashan Saltern in China. Carbonate minerals induced by LD532 were investigated in several sets of comparative experiments that employed magnesium sulfate and magnesium chloride as Mg resources. Magnesium calcite and aragonite were induced by LD532 bacteria, whereas these minerals did not appear in the control group. The mineral phases, micromorphologies, and crystal structures were analysed using X-ray powder diffraction, scanning electron microscopy, and energy dispersive X-ray detection. The carbonic anhydrase and urease secreted by strain LD532 through metabolism increased the pH value of the liquid medium and promoted the process of carbonate precipitation. Further study using high resolution transmission electron microscopy, energy dispersive X-ray detection and analysis of ultrathin slices showed that the nucleation sites of carbonate minerals were located on extracellular polymeric substances and the membranes of intracellular vesicles of LD532 bacteria, which provided favourable conditions for the growth of carbonate mineral crystals. The morphologies and compositions of minerals formed in solutions of MgSO₄ and MgCl₂ display significant differences, indicating that different sources of Mg²⁺ may also affect the physiological and biochemical activities of microorganisms and thus mineral deposition. This study will be of some interest for the interpretation of carbonate biomineralization in natural salt environments and has some value as a reference in understanding sedimentary carbonates in ancient marine environments, such as tidal flats.

The recent decade has witnessed the evolution of a novel paradigm of alloying which is based on utilising multiple elements to design compositionally complex alloys also known as high entropy alloys (HEAs). Conventional manufacturing of HEAs has a number of drawbacks, especially in terms of mechanical properties and design complexities. This has been addressed by additive manufacturing (AM), which has not only led to the fabrication of complex-shaped HEA components but has also enabled both ex-situ and in-situ tailoring of alloy microstructures. Considering the increasing interest in AM-based fabrication of HEAs in the last ten years, the present chapter is aimed at highlighting the present status and challenges in the avenue of AM of HEAs. This has been followed by a discussion on the recent trends in the avenue of AM-based fabrication of HEAs from the viewpoints of (i) microstructure evolution and mechanical properties, and (ii) alloy fabrication techniques. The chapter ends with a discussion on the future prospects in the aforementioned avenue.

Co-Zr amorphous alloys exhibit soft magnetic properties, whereas Co-rich crystalline magnetic phases in this alloy system display hard magnetic behaviour. In this study, an initial two-phase Co-Zr composite with an overall composition of 75 at.% Co and 25 at.% Zr was processed by high pressure torsion (HPT) and the effects of severe plastic deformation and subsequent thermal treatment on the structural evolution and its magnetic properties have been investigated. HPT processing allowed us to achieve an amorphous microstructure in the as-deformed state with low coercivity. To further tune magnetic properties and study the alloys’ crystallization behaviour, various annealed states are investigated. Microstructural properties are correlated to the magnetic properties and a decreasing coercivity with increasing annealing temperature is observed despite the onset of crystallization in the amorphous alloy. At higher annealing temperatures, coercivity increases again. The results appear promising to obtain tuneable rare-earth free magnetic materials by severe plastic deformation.

Understanding of the correlation between the magnetomechancial coupling factors (k) and damping factors (Q^-1) is a key pathway to enhance the magnetomechanical power conversion ef-ficiency in laminated magnetoelectric (ME) composites by engineeringly manipulating the magnetic and mechanical properties of Fe-based amorphous metals. The k and Q^-1 factors of FeSiB amorphous ribbons annealed in air at different temperatures are investigated. It is found that k and Q^-1 factors are affected by both magnetic and elastic properties. The magnetic and elastic properties are equalized in terms of the magnetomechanical power efficiency for the low temperature annealing. The k and Q^-1 of FeSiB-based epoxied laminates with different stacking numbers show that the -3 dB bandwidth and Young’s modulus are equalized in terms of the magnetomechanical power efficiency for the high lamination stacking.

In this investigation, Cu-Ni alloys for possible fixed dental prostheses (FDPs), with different aluminum additions were produced using vacuum atmosphere. Annealed alloys (He atmosphere) with low aluminum concentration showed a coarse dendritic structure, while samples with high aluminum concentration showed a refined dendritic structure. Structural defects analyses have shown a relative low vacancy concentrations. Hardness value increases approximately five times for the alloyed samples compared with the as-cast and unalloyed samples. Compression test results have shown a noticeable strengthening improvement, mainly in samples heat treated with 10 at % Al, while samples with 5 at % Al presented also acceptable resistance. Results are discussed in terms of dislocation mobility and hardening precipitation mechanism.

One of the modern methods of improving operating characteristics of titanium and titanium-based alloys under conditions of friction and increased contact loads is the method of ion-plasma nitriding. The effect of nitriding of VT5 alloy (Al 4,5-6,7 %, V to 1,2 %, Mo to 0,8 % − analogue 3.7115) in the plasma of a glow discharge excited in a hollow cathode on its tribological characteristics in pairs with different materials in T-1 fuel and under dry friction conditions has been studied. For research and tribological tests, samples of VT5 alloy were nitrided in the plasma of a glow discharge excited in a hollow cathode at a temperature of 975 ± 15°C and a pressure of 58 ± 2 PA in a nitrogen-argon gas mixture with a nitrogen content of 78 %. Studies of samples of VT5 alloy after nitriding showed that the surface roughness Ra was in the range of 0.58-0.64, and the surface hardness HV5 was 525 ± 20 kgf/mm² at a base hardness of 325 ± 15 kgf/mm². Tribological tests were performed on a friction machine 2070 SMT-1 according to the scheme "cube - roller". Tests under conditions of friction with oil were performed at a load of 200 N. The sliding speed during the tests was 1.3 m/s, the test time was 75 sec. The test under dry friction conditions was carried out at a load of 100 N and a sliding speed of 0.785 m/s, the test time was 30 minutes. Low wear ability in relation to the nitrided titanium alloy VT5 (<2.4x10^-4 mm³/s), as well as friction coefficients at the level of 0.08 to 0.12 in the order of their growth had bronze VB-23NTS (Pd 18–22 %, Ni 3–4 %, Zn 3–4 %, Sb 3–4 %, P 0.15–0.3) r.O10C2N3, VB-24 (Sb 4.7–6, 2 %, P 0.4–0.9), steel 1.3505, cast iron GGG80, cemented steel 20Cr3MoWV.

Doped copper overpacks are planned to be utilized in the spent nuclear fuel repositories in Finland and in Sweden. The assessment of long-term integrity of the material is a matter of importance. Grain structure variations, segregation and any possible manufacturing defects in microstructure are relevant in terms of susceptibility to creep and damage from the loading evolution imposed by its operating environment. This work focuses on studying the microstructure level length-scale dependent deformation behavior of the material, of particular significance with respect to accumulation of plasticity over the extensive operational period of the overpacks. Reduced micromorphic crystal plasticity model, which is similar to strain gradient models, is used in this investigation. Firstly, the model’s size dependent plasticity effects are evaluated. Secondly, different microstructural aggregates presenting overpack sections are analyzed. Grain size dependent hardening responses, i.e., Hall-Petch like behavior, can be achieved with the enhanced hardening associated with the micromorphic model at polycrystalline level. It was found that the nominally large grain size in the base material of the overpack shows lower strain hardening potential than the fine grained region of the welded microstructure with stronger strain gradient related hardening effects. Size dependent regularization of strain localization networks is indicated as a desired characteristics of the model. The findings can be utilized to provide an improved basis for modeling the viscoplastic deformation behavior of the studied copper alloy and assess the microstructural origins of any integrity concerns explicitly by way of full field modeling.

This work explored and contrasted the effect of microstructure on the tensile properties of AlSi10Mg alloys generated by transient directional solidification depending on variations in cooling rate and Magnesium (Mg) content (i.e., 0.45 and 1wt.% Mg), with a focus on understanding the dendritic growth and phases constitution. Optical and Scanning electron (SEM) microscopies, CALPHAD and thermal analysis were used to describe the microstructure, forming phases and resulting tensile properties. The findings showed that the experimental evolution of the primary dendritic spacing is very similar when both directionally solidified (DS) Al-10wt.% Si-0.45wt.% Mg and Al-10wt.% Si-1wt.% Mg alloys samples are compared. The secondary dendritic spacing was lower for the alloy with more Mg, especially considering the range of high growth velocities. Moreover, a greater fraction of (Al+Si+Mg2Si) ternary eutectic islands surrounding the -Al dendritic matrix was noted for the alloy with 1wt.% Mg. As a result of primary dendritic spacings greater than 180 m related to lower cooling rates, slightly higher tensile properties were attained for the Al-10wt.% Si-0.45wt.% Mg alloy. In contrast, combining dendritic refining (< 150 m) and larger Mg2Si fraction, fast solidified DS Al-10wt.% Si-1wt.% Mg samples exhibited higher tensile strength and elongation. The control of cooling rate and fineness of the dendritic array provided a new insight related to the addition of Mg in slightly higher levels than conventional ones, capable of achieving a better balance of tensile properties in AlSi10Mg alloys.

The structural and strength analysis of the material used to construct such an important engine element as the turbine is of great significance, both at the design stage as well as during tests and expertises related to emergency situations. Bearing in mind the conditions above mentioned, the paper presents the results of research on the chemical composition, morphology and phased structure of the metallic construction material used to produce the blades of the high and low pressure turbine of the RD-33 jet engine, which is the propulsion unit of the MiG-29 aircraft. The data obtained as a result of the material tests of the blades allowed, on the basis of the analysis of chemical composition and phased structure, to determine the grade of the alloy used to construct the tested elements of the jet engine turbine. The structural stability of the material was found to be lower in comparison with engine operating conditions, which manifested itself as a clear decrease in the resistance properties of the blade material. The results obtained can be used as a basis for analyzing the life span of an object or a selection of material replacements, which enable to produce the analyzed engine element.

Nanostructured anodic oxide layers on an FeAl₃ intermetallic alloy were prepared by two-step anodization in 20 wt.% H2SO4 at 0°C. The voltage range was 10.0 – 22.5 V with a step of 2.5 V. The structural and morphological characterizations of the received anodic oxide layers were performed by FE-SEM. Therefore, the formed anodic oxide was found to be highly porous with a high surface area, as indicated by the FE-SEM studies. It has been shown that the morphology of fabricated nanoporous oxide layers is strongly affected by the anodization potential. The oxide growth rate first increased slowly (from 0.010 μm/s for 10 V to 0.02 μm/s for 15 V) and then very rapidly (from 0.04 μm/s for 17.5 V up to 0.13 μm/s for 22.5 V). The same trend was observed for the change in the oxide thickness. Moreover, for all investigated anodizing voltages, the structural features of the anodic oxide layers, such as the pore diameter and interpore distance, increase with increasing anodizing potential. The obtained anodic oxide layer was identified as a crystalline FeAl₂O₄, Fe₂O₃ and Al₂O₃ oxide mixture.

The effect of microstructure and chemistry of passive films on the kinetics of passive layer growth and passivity breakdown of some Ti-based alloys, namely Ti-6Al-4V, Ti-6Al-7Nb and TC21 alloys was studied. The rate of pitting corrosion was evaluated using cyclic polarization measurements. Chronoamperometry was applied to assess the passive layer growth kinetics and breakdown. Microstructure influence on the uniform corrosion rate of these alloys was also investigated employing Tafel extrapolation and dynamic electrochemical impedance spectroscopy. Corrosion studies were performed in 0.9% NaCl solution at 37 oC, and the obtained results were compared with ultrapure Ti (99.99%). The different phases of the microstructure were characterized by X-ray diffraction and scanning electron microscopy. Chemical composition and chemistry of the corroded surfaces were studied using X-ray photoelectron analysis. For all studied alloys, the microstructure consisted of α matrix, which was strengthened by β phase. The highest and the lowest values of the β phase’s volume fraction were recorded for TC21 and Ti-Al-Nb alloys, respectively. The uniform corrosion rate and pitting corrosion resistance (R_pit) of the studied alloys were enhanced following the sequence: Ti-6Al-7Nb < Ti-6Al-4V << TC21. The corrosion resistance of Ti-Al-Nb alloy approached that of pure Ti. The obvious changes in the microstructure of these alloys, together with XPS findings, were adopted to interpret the pronounced variation in their corrosion rates.

Transient liquid phase (TLP) bonding of Al-6063 and UNS S32304 was performed using copper foil as an interlayer between the base metals. A compression load was applied normal to the specimens. Metallurgical examination of the produced joints showed three distinct regions including a reaction zone, diffusion affected zone and the base metals. The diffusion of copper into aluminum resulted in an Al-Cu eutectic structure. However, the oxide layer on the aluminum surface controlled the dissolution behavior of copper and the extent of its wettability with the base metals. Although voids and intermetallic compounds were detected at the interfaces of the processed joints, a defect free joint was produced at 570°C. In addition, the results from corrosion tests showed that the use of copper as an interlayer decreased the corrosion resistance of the joints. However, increase in thickness of the joining reaction zone with increasing bonding temperature was observed to increase corrosion resistance.

1) Background: The objective was to evaluate the corrosion resistance of different commercially pure ultrafine-grained (UFG) titanium and its alloys with acid etched surface processed by equal-channel angular pressing (ECAP); 2) Methods: Coarse-grained and UFG titanium samples were investigated using polarization resistance technique. Surface characteristics of the native oxidized layer were evaluated by TEM and XRD. Electrochemical tests were under physiological electrolyte at a rate of 1 and 10 mV/s. Weight loss tests were performed after immersion into HCl solution for up to 3 years; 3) Results: UFG titanium was less susceptible to corrosion which was identified under lower rates and at higher polarization resistance than its coarse grain counterparts. Titanium Grade 2 and Grade 4 demonstrated similar corrosion susceptibility. Titanium Grade 5 revealed a thin and tightly adhered native oxide layer with adequate corrosion resistance; 4) Conclusions: ECAP process imposed a more compact and adhered oxidized layer. Surface etching techniques delivered a thicker native TiO₂ layer, being both grain refinement and surface etching techniques responsible for the improved corrosion resistance of Titanium samples under physiological environment after 3 years of observation.

Yellow nanorod Mg-MOF-74 was obtained by solvothermal synthesis method. XRD、N2 adsorption-desorption isotherms、SEM and TGA results suggest that the particle size of Mg-MOF-74 reaches 400 nm after the introduction of sodium acetate in the precursor of Mg-MOF-74. Besides, the morphology of Mg-MOF-74 was changed from cauliflower to rod particles. At the same time, the BET specific surface area and pore volume of Mg-MOF-74 were also increased a lot. Then the CO2 dynamic adsorption capacity of Mg-MOF-74 was measured by self-made fix bed under 30 ℃、0.1 bar CO2 partial pressure. The results show that the CO2 adsorption capacity of Mg-MOF-74-N2 reaches 3.67 mmol/g and its CO2 adsorption capacity remains unchanged after 10 times CO2 adsorption-desorption cycles.

In this study, the effect of increasing exposure time on microstructures, defectiveness, mechanical properties and corrosion behavior of selective laser melted sample Al-Si10-Mg powder have been investigated. The sample were processed at the same power (375 W) and scan speed (2000 mm/s) but with increasing exposure time. Exposure time equal to 40, 50 and 60 µs was applied. The features of the analyzed samples show that with increasing exposure time a better efficiency of the heat input has been obtained with larger size of melting pool and Si particles and lower defectiveness. Moreover, being the coarser microstructure associated a to lower level of voids, the average hardness is similar for the analyzed samples. The potentiodynamic curves of the samples show that the voids occurrence is more significant with respect to the scale of micro-structure on corrosion behavior being the sample processed at the highest exposure time the more resistant to corrosion. The experimental techniques used in the present study were Optical microscope, Sem microscope, Hardness and X-Ray Computed Tomography.

In this paper, the phases in the Mg-Ti-O system using the 1:1 formulation of MgO:TiO2 mixing synthetic brucite of Mexican origin with TiO2 microparticles of high purity and with a heat treatment at 1100°C for 1 h were studied. The raw materials and formulation by XPS and DRX techniques were characterized. The results demonstrate the presence of different oxidation states in titania and the formation of different oxides in the Mg-Ti-O system when mixed and calcined at 1100°C; additionally, the formation of vacancies in the crystal lattice during the transformation from hexagonal brucite to magnesia with a cubic structure centered on the faces is estimated. With the results, its thermal behavior is warned based on the MgO-TiO2 phase diagram.

Biomineralization has become a research hotspot and attracted widespread attention in the field of carbonate sedimentology. In this study, Bacillus licheniformis DB1-9 was used to induce the calcium carbonate precipitation at different magnesium calcium molar ratios in the laboratory to further explore the biomineralization mechanism. Phylogenetic tree shows that the bacteria belongs to Bacillus licheniformis species. The ammonia and carbonic anhydrase can be released by this bacteria, resulting in the pH increase, and the carbonic anhydrase can also promote the hydration reaction of carbon dioxide and subsequently produce the bicarbonate and carbonate ions to elevate the supersaturation of calcium carbonate in the liquid culture medium to facilitate the precipitation of carbonate minerals. The calcites have a shape of rhombohedron, dumbell, and elongation, and aragonite often appears in the form of mineral aggregates, besides that there are also the spherical and the fusiform minerals. FTIR result shows there are some organic functional groups, such as C-O-C and C=O, beside of the characteristic peaks of the calcite and the aragonite, indicating that microbial metabolism is closely related to the mineral formation. The superthin slices of the bacteria analyzed by HRTEM, SAED, EDS and STEM show that the surface and EPS can adsorb a large number of calcium ions and magnesium ions and EPS may act as the nucleation sites, what’s more, the intracellular nanometer-scale sphere areas show the amorphous structures, and the intracellular calcium ions and magnesium ions suggeste that they can be transported from the outside to inside the cell by diffusion along the concentration grade from high to low. This study may provide some references to further understand the biomineralization mechanism induced by microorganisms in the laboratory and the field, and also helps to explore the reason of the transition of calcite sea to aragonite sea in the geological history.

Present work has systematically investigated the evolution of dispersoid and elevated-temperature properties including the strength and creep resistance during the various multi-step heat treatments in Al-Mn-Mg 3004 alloys. Results show that only α-Al(MnFe)Si dispersoid is observed in the studied temperature range (up to 625°C) and it coarsens with increasing temperature to 500°C but dissolves at 625°C. The evolution of elevated-temperature strength and creep resistance is greatly related to the temperature of each step during the multi-step heat treatments. Generally, lower temperature at the first-step heat treatment leads to higher properties while the properties decrease with increasing temperature of last-step heat treatment. Suitable models have been introduced to explain the evolution of strength and the creep threshold stress at elevated-temperature during the various heat treatments.

Semi-solid feedstock of AZ80 magnesium alloy modified by minor rare-earth Y element (0, 0.2, 0.4, 0.8 wt.%) were fabricated by strain induces melting activated (SIMA) in the form of extrusion and partial remelting. The effect of Y addition on the microstructure evolution of extruded and isothermal treated alloy was observed by optical microscope (OM), scanning electron microscope (SEM), X-ray diffraction (XRD) and quantitative analysis. The results show that the Y addition can refine the microstructure and make the β-Mg17Al12 phases agglomerating. During the subsequent isothermal treatment at 570℃, the average solid grain size, shape factor and liquid fractions increased with prolonged soaking time. Smaller spheroidal solid grains and the larger shape factor were obtained due to Y addition. The coalescence and Ostwald ripening of solid grains operated the coarsening process simultaneously. The coarsening rate constants of AZ80M1 (0.2 wt.% Y addition) of 164.22 μm3s-1 was approximately four times less than the un-modified AZ80 alloy of 689.44 μm3s-1. In contrast, the desirable semi-solid structure featured by fine, well globular solid grains and appropriate liquid fractions and shape factor was achieved in AZ80M1 alloy treated at 570℃ for 20-30 min.

This paper illustrates an experimental activity for the closed-loop position control of an actuator made using shape memory alloy (SMA) wire. A solution with the self-sensing effect was implemented to miniaturize the systems, i.e., without external sensors. A proportional control algorithm was initially used, demonstrating the idea's feasibility: the wire can behave simultaneously as an actuator and sensor. An experimental investigation was subsequently conducted for the optimization of the developed actuator. As for the material, a Flexinol wire, Ni-Ti alloy, with a diameter of 0.150 mm and a length of 200 mm, was used. Preliminarily, a characterization of the SMA wire at constant and variable loads was carried out: the characteristics detected are elongation vs. electric current and elongation vs. electrical resistance. The control system is PC-based with a data acquisition card (DAQ). A drive board has been designed and built to read the wire's electrical resistance and power it by pulse width modulation (PWM). A notable result is that the actuator works with good precision and in dynamic conditions, even when it is called to support a load up to 65% different from that for which the electrical resistance-length correlation has previously been experimentally obtained, on which the control is based. This opens up the possibility of using the actuator in a counteracting configuration with a spring, which makes hardware implementation and control management simple.

Sr4Al6O12SO4 samples were obtained from the compound mixture formed by a solid–state reaction of Al2O3, SrSO4, and SrCO3. Samples were compacted at 100MPa to form pellets of 1 and 4cm in diameter and were sintered at 1400°C for 4 hours. The compound was analyzed by X–ray diffraction. Static immersion and wettability tests were performed to evaluate corrosion resistance in contact with Al–Si. Corrosion tests were carried out by immersion at 800, 900, and 1000°C for 24, 50, and 100 hours, while wettability was carried out at 900, 1000, and 1100°C for 2 hours. Subsequently, the samples were prepared metallographically. Samples were analyzed by optical microscopy, scanning electron microscopy, and image analysis. In general, reaction products consisting of alumina, spinel, oxides, and sulfates were found. The contact angles obtained were 124° to 135°. It is concluded that ceramic substrate Sr4Al6O12SO4 is resistant to corrosion by Al–Si alloy, since the slight thickness of the reaction products found in the samples (100μm) considering the severe conditions of the experiment: 1000°C and 100 hours of isothermal temperature. Furthermore, it can be said that Sr4Al6O12SO4 is not wettable by Al–Si alloys.

We used the Taylor-Ulitovsky Technique to prepare nanocrystalline Co2MnGe Heusler alloy glass-coated microwires with a metallic nucleus diameter of 18 ± 0.1 µm and a total diameter of 27.2 ± 0.1 µm. Magnetic and structural studies were carried out to determine the fundamental magneto-structural characteristics of Co2MnGe glass-coated microwires. XRD revealed a well-defined nanocrystalline structure with average grain size about 63 nm, lattice parameter a = 5.62 and a unique mixture of L21 and B2 phases. The magnetization curves for field cooling and field heating (FC-FH) demonstrate a considerable dependence on the applied magnetic field, ranging from 50 Oe to 20 kOe. Internal stresses, originated by the production process, resulted in various magnetic phases, which were responsible for the notable difference of field cooling (FC) and field heating (FH) curves on magnetization dependence versus temperature. Furthermore, the ferromagnetic behavior and expected high Curie temperature together with high degree of L21 ordered makes it a promising candidate for many applications.

The conductor aluminum alloys Al-0.25wt.%Zr doped additionally with Х = Er, Si, Hf, and Nb were the objects of investigations. The fine-grained microstructure in the alloys was formed by Equal Channel Angular Pressing and Rotary Swaging. The thermal stability of the microstructure, specific electrical resistivity, and microhardness of the novel conductor aluminum alloys was investigated. The mechanisms of nucleation of the Al3(Zr,X) secondary particles during annealing the fine-grained aluminum alloys were determined using Jones-Mehl-Avrami-Kolmogorov equation. Using Zener equation, the dependencies of the mean secondary particle sizes on the annealing time were obtained on the base of analysis of the data on the grain growth in the aluminum alloys. The secondary particle nucleation during long-time low-temperature annealing (300 оC, 1000 hrs) was shown to go preferentially at the cores of the lattice dislocations. The Al-0.25%Zr-0.25%Er-0.20%Hf-0.15%Si alloy subjected to long-time annealing at 300 оC has the optimal combination of the microhardness and electrical conductivity (59.8%IACS, Hv = 480 ± 15 MPa).

The research was undertaken to study the way deformation behaves in ultrafine-grained (UFG) conducting Al-Zr alloys doped with Sc, Hf, and Yb. All in all, 8 alloys were studied with zirconium partially replaced by Sc, Hf, and/or Yb. Doping elements (X = Zr, Sc, Hf, Yb) in the alloys total 0.4 wt.%. The choice of doping elements is conditioned by possible precipitation of Al3X particles with L12 structure while annealing these alloys. Such particles provide higher thermal stability of a nonequilibrium UFG microstructure. Initial coarse-grained samples were obtained by induction casting. The UFG microstructure in the alloys was formed by Equal Channel Angular Pressing (ECAP) at 225°C. Superplasticity tests were carried out at temperatures ranging from 300 to 500 °C and strain rates varying between 3.310-4 and 3.310-1 s-1. The highest values of elongation to failure are observed in Sc-doped alloys. A UFG Al-0.2%Zr-0.1%Sc-0.1%Hf alloy has maximum ductility: at 450 °C and a strain rate of 3.310-3 s-1, relative elongation to failure reaches 765%. At the onset of superplasticity, stress–strain curves are characterized by a stage of homogeneous strain and a long stage of localized plastic flow. The dependence of homogeneous strain (eq) on test temperature in UFG Sc-doped alloys is increasing uniformly, which is not the case for other UFG alloys with eq(T) dependence peaking at 350-400 оС. Strain rate sensitivity coefficient of flow stress m is small and does not exceed 0.26-0.3 at 400-500 °C. In UFG alloys containing no scandium, m coefficient is observed to go down to 0.12-0.18 at 500 оС. It has been suggested that lower m values are driven by intensive grain growth and pore formation in large Al3X particles, which develop specifically at the ingot crystallization stage.

The solid-state welding method known as friction stir welding (FSW) bonds two metallic work parts, whether the same or different, by plastically deforming the base metal. The frictional resistance between both metallic work pieces causes them to produce heat, which produces plastic deformation and welds them. However, the weldability and strength of FSW joints mainly depend on the FSW parameters. This review work highlights the previous research work on the FSW parameters and their effects on the weldability and quality of the aluminum alloys joined with similar and dissimilar metals through the FSW method. About 150 research studies were systematically reviewed, and the articles included data from peer-reviewed journals. It has been concluded that the key parameters, including welding speed, “rotational speed”, “plunge depth”, “spindle torque”, “shoulder design”, “base material”, “pin profile” and “tool type", significantly affect the weldability of the aluminum joint through the FSW method. Also, the selection of these parameters is important and fundamental as they directly affect the joint. It is recommended that future work focus on FSW for aluminum. Among these, the most essential is the application of artificial intelligence (AI) techniques to select the optimum FSW parameters for aluminum welding.

Controlled deposition of CoCrFeNiMo0.2 high entropy alloy (HEA) micro-particles was achieved using laser induced forward transfer (LIFT). Ultra-short laser pulses, 230 fs of 515 nm wavelength, were tightly focused into ∼ 2.4 μm focal spots on the ∼50 nm thick plasma-sputtered films of CoCrFeNiMo0.2. The HTA films were transferred onto glass substrates by magnetron sputtering in vacuum (10−8 atm) from the thermal spray coated substrates. The absorption coefficient of CoCrFeNiMo0.2 α ≈ 6 × 105 cm−1 was determined at 600 nm wavelength. The real and imaginary parts of refractive index (n + iκ) of HEA were determined from reflectance and transmittance using nano-films.

Magnesium is a promising material. It has a remarkable mix of mechanical and biomedical properties that made it suitable for a vast range of applications. With alloying, many of these inherent properties can be further improved. Today, it is primarily used in the automotive, aerospace, and medical industry. However, magnesium has its own set of drawbacks which the industry and research community are actively addressing. Magnesium’s rapid corrosion is its most significant drawback, and it dramatically impeded magnesium’s growth and expansion into other applications. This article will review both the engineering and biomedical aspects and applications for magnesium and its alloys. It will also elaborate on the challenges the material faces, how they can be overcome, and its outlook.

The relative dislocation density of aluminum and copper samples is quantitatively measured using linear Resonant Ultrasound Spectroscopy (RUS). For each metallic group, four samples were prepared with different thermomechanical treatments in order to induce changes in their dislocation densities. The RUS results are compared with Nonlinear Resonant Ultrasound Spectroscopy (NRUS) as well as Second Harmonic Generation (SHG) measurements. NRUS has a higher sensitivity by a factor of two to six and SHG by 14% to 62%. The latter technique is, however, faster and simpler. As main a result we obtain a quantitative relation between the changes in the nonlinear parameters and the dislocation density variations, which in a first approximation is a linear relation between these differences. We also present a simple theoretical expression that explains the better sensitivity to dislocation content of the nonlinear parameters with respect to the linear ones. X-Ray diffraction measurements, although intrusive and less accurate, support the acoustics results.

Addressing the issue of low bonding strength in Ti/Mg laminated composites due to interfacial oxidation, this study employs a differential temperature rolling method using longitudinal induction heating to fabricate Ti/Mg composite plates. The entire process is conducted under an argon gas protective atmosphere, which prevents interfacial oxidation while achieving uniform deformation. The effects of reduction on the mechanical properties and microstructure of the composite plates are thoroughly investigated. Results indicate that as the reduction increases, the bonding strength gradually increases, mainly attributed to the increased mechanical interlocking area and a broader element diffusion layer. This corresponds to a transition from brittle to ductile fracture at the microscopic tensile-shear fracture surface. When the reduction reaches 47.5%, the Ti/Mg interfacial strength reaches 63 MPa, which is approximately a 20% improvement compared to the bonded strength with previous oxidation at the interface. Notably, at a low reduction of 17.5%, the bonding strength is significantly enhanced by about 1 time. Additionally, it is found that a strong bonded interface at high reduction is beneficial in hindering the propagation of interfacial cracks during tensile testing, enhancing the ability of the Ti/Mg composite plates to resist interfacial delamination.

Current Li battery technology employs graphite anode and flammable organic liquid electrolytes. Thus, current Li battery is always facing the problems of low energy density and safety. Additionally, sustainable supply of Li due to scarce abundance of Li sources is another problem. All-solid-state Mg battery is expected to solve the problems owing to non-flammable solid-state electrolytes, high capacity/safety of divalent Mg metal anode and high abundance of Mg sources. Therefore, solid-state electrolytes and all-solid-state Mg battery have been researched intensively last two decades. However, realization of all-solid-state Mg battery is still far. In this article, we review recent research progress on all-solid-state Mg battery so that researchers can pursue recent research trend of all-solid-state Mg battery. At first, solid-state electrolyte research is described briefly in the categories of inorganic, organic and inorganic/organic composite electrolytes. After that, the recent research progress of all-solid-state Mg battery is summarized and analyzed. To help readers, we tabulate electrode materials, experimental conditions and performances of all-solid-state Mg battery so that the readers can find necessary information at a glance. In the last, challenges to realize the all-solid-state Mg batteries are visited.

The fatigue crack growth rate (FCGR) of aluminium alloys under the combined influence of temperature and humidity remains a relatively unexplored area, receiving limited attention due to its intricate nature and challenges in predicting the combined impact of these factors. The challenge was to investigate and address the specific mechanisms and interactions between temperature and humidity, as in coastal environment conditions, on the FCGR of aluminium alloy. The present study conducts a comprehensive investigation on the combined influence of temperature and humidity on the FCGR of Al6082 alloy. The fatigue pre-cracked compact tension specimens were corroded for 7 days and then subjected to various temperature and humidity conditions in a thermal chamber for 3 days to simulate coastal environments. The obtained data were analysed to determine the influence of temperature and humidity on the FCGR of Al6082 alloy. An empirical model was also established to predict fatigue life cycle values under these environmental conditions precisely. The correlation between FCGR and fracture toughness models was also examined. The Al6082 alloy exhibits a 34% increase in the Paris constant C, indicating reduced FCGR resistance due to elevated temperature and humidity levels. At the same time, fatigue, corrosion, moisture-assisted crack propagation, and hydrogen embrittlement lead to a 27% decrease in threshold fracture toughness. The developed model exhibited accurate predictions for fatigue life cycles, and the correlation between fracture toughness and FCGR showed less than 10% error, indicating a strong relationship between these parameters.

The theory of heterogeneous nucleation was initially developed as a part of condensed matter physics and later it was used as an important engineering tool to design metallurgical processes. The success leads to wide applications of the theory in metallurgical practice. For example, engineering heterogeneous nucleation in ductile iron has been used to reduce shrinkage defects, suppress cementite formation, and modify size and shape of micro-structural constituencies. This demonstrates how theoretical knowledge could benefit industry practice. This overview aims to summarize the authors’ published studies in co-authorship with colleagues and students, which covered different aspects of engineering heterogeneous nucleation in multiphase cast alloys. Several approaches for engineering heterogeneous nucleation using thermodynamic simulation and practical methods for improving efficiency of nucleation using co-precipitation technique and a local transient melt supersaturation were suggested. Automated Scanning Electron Microscopy Energy-Dispersive-X-ray (SEM/EDX) analysis and a high-resolution Transmission Electron Microscopy (TEM) were used to verify simulation predictions. Practical examples of controlling micro-porosity shrinkage in cast irons with spheroidal graphite are presented to illustrate the power of engineering heterogenous nucleation. The authors appreciate the great efforts that the co-authors have made on the original, overviewed articles here.

The development of Al-Ni alloys with a controlled microstructure has had a great impact on the field of study of aluminum-based alloys. In the present research, the influence of thermal parameters on the grain structures resulting from the directional solidification process of Al-Ni alloys with different alloy content has been studied. It has also been evaluated how different structures and the distribution of second phases influence the corrosion behavior and microhardness of alloys. The columnar-to-equiaxed transition (CET) was observed to occur when the temperature gradient in the melt decreased to values between 1.3 to 2.9 ° C/cm. In addition, a small increase in the microhardness values was observed as a function of the Ni-content. When the Ni-content increase, the resistance to polarization decreases for samples with equiaxed grain structure, throughout the range of compositions studied. Furthermore, the equiaxed grain structure presents higher resistance to polarization values than the columnar grain zone, for alloys with a composition equal to or lower than the eutectic composition.

New ways of generating energy are currently being discussed, with a transition from traditional primary sources to more environmentally friendly options, particularly renewables. Energy storage is also closely related to this transition. Battery storage currently dominates this area. However, flywheel energy storage system (FESS) technology offers an alternative that uses stored kinetic energy to be transformed into mechanical energy and, using a motor-generator, electrical energy. FESS technology is thus flexible and can be applied in different industrial applications. The management of the technology of recycling W-MMC waste material from other products and the subsequent trial production of high-strength W-MMC material with a density of more than 17 500 kg/m3 from recycled powders allowed to test the limits of the so-called "heavy" flywheels used in rotor production. Materials with densities ≥ 7 800 kg/m3, and operating at lower to medium speeds up to 20 000 rpm. The results achieved lead to the conclusion that the developed recycled materials of the W-MMC type with a density ≥ 17 500 kg/m3, with a yield strength of 1 200 - 1 700 MPa depending on the production method, can be used as a substitute for the structural steels used today, without an enforced reduction of the maximum allowed rotor speed due to exceeding the maximum allowed stress.

The direct measurements of the magnetocaloric effect were performed in Heusler Ni44.4Mn36.2Sn14.9Cu4.5 alloy at cryogenic temperatures in magnetic fields up to 10 T. The maximum value of the inverse magnetocaloric effect in a field of 10 T was observed ∆Tad = –2.7 K in the vicinity of the 1st order magnetostructural phase transition at T0 = 117 K. The ab initio and Monte Carlo calculations were performed to discuss the effect Cu doping into Ni-Mn-Sn compound on the ground state structural and magnetic properties. It is shown that with increasing Cu content the martensitic transition temperature decreases and the Curie temperature of austenite slightly increases. In general, calculated transition temperatures, magnetization values are correlated well with the experimental ones.

The mechanical properties, structure, and morphology of milled and 3D printed Ti-6Al-4V alloys produced by selective laser melting were investigated in this study. The mechanical properties were investigated by means of nanoindentation, a tensile test, and a three-point bending test. The Atomic Force Microscope (AFM) was used to study the surface topography and roughness of both titanium alloys. The surface structure and phase analysis were studied by a scanning electron microscope (SEM) and through powder X-ray diffraction (XRD). The results from the nanoindentation experiments showed that the 3D-printed sample has higher indentation hardness and modulus than the milled one. The AFM observation of the surface topography of the samples showed that the milled sample has a higher roughness than the 3D-printed one. The tensile test results showed that the 3D printed sample by means of Selective Laser Melting (SLM) technology has about 26% higher tensile strength and smaller elongation than the milled one. The 3-point bending test revealed that the 3D printed Ti-6Al-4V sample has higher flexural strength than the milled one. It was found that the 3D-printed sample has a smaller crystal size than the milled one, which, according to the Hall-Petch relationship, leads to its higher indentation hardness.

We studied Ni2FeSi, Co2FeSi and Co2MnSi -based full Heusler alloy glass-coated microwires with the same geometric aspect ratio ρ ≈ 0.50 ± 0.01 prepared using Taylor-Ulitovsky method. The fabrication of X2YZ; (X = Co &amp; Ni, Y = Fe &amp; Mn and Z = Si) based glass coated microwires with fixed aspect ratio is a quite challenging due to the different samples preparation conditions. The XRD analysis shows nanocrystalline microstructure for all the samples. Space group Fm3¯m (FCC) with disordered B2 and A2-types for Ni2FeSi and Co2FeSi and ordered L21-type for Co2MnSi are observed. The change in the positions of Ni, Co and Mn, Fe in X2YSi resulted in a variation in the lattice cell parameters and the average grain size of the sample. Room temperature magnetic behavior shows a dramatic change depending on the chemical composition, where Ni2FeSi-MWs shows the highest coercivity (Hc) compared to Co2FeSi-MWS and Co2MnSi-MWs. The Hc –value of Ni2FeSi-MWs is 16 times higher than that of Co2MnSi-MWs and 3 times higher than that of Co2FeSi-MWS. Meanwhile, the highest reduced remanence is reported for Co2FeSi-MWS (Mr =0.92), , being about 0.33 and 0.22 for Ni2FeSi-MWs and Co2MnSi-MWs, respectively. From the analysis of the temperature dependence of the magnetic properties (Hc and Mr) of X2YZ-MWs we deduced that Hc shows a stable tendency for Co2MnSi-MWs and Co2FeSi-MWs, meanwhile two flipped points are observed for Ni2FeSi-MWs where the behavior of Hc changes with temperature. For Mr monotonic increase by decreasing the temperature is observed for Co2FeSi-MWs and Ni2FeSi-MWs and roughly stable for Co2MnSi-MWs. The thermomagnetic curves at low magnetic field show irreversible magnetic behavior for Co2MnSi-MWs and Co2FeSi-MWs and regular ferromagnetic behavior for Ni2FeSi-MWs. The current result illustrates the ability to tailor the structure and magnetic behavior of X2YZ-MWs at a fixed internal stresses, i.e., with fixed aspect ratio. Additionally, a different behavior was revealed in X2YZ-MWs depending on the degree of ordering and elements distribution. The tunability of magnetic properties of X2YZ-MWs makes them suitable for sensing applications.

Group-IV GeSn photodetectors (PDs) compatible with standard complementary metal-oxide-semiconductor (CMOS) processing have emerged as a new and non-toxic infrared detection technology to enable a wide range of infrared applications. The performance of GeSn PDs is highly dependent on the Sn composition and operation temperature. Here, we develop theoretical models to establish a simple rule of thumb, namely “GeSn-rule 23”, to describe GeSn PDs’ dark current density in terms of operation temperature, cutoff wavelength, and Sn composition. In addition, analysis of GeSn PDs’ performance shows that the responsivity, detectivity, and bandwidth are highly dependent on operation temperature. This rule provides a simple and convenient indicator for device developers to estimate the device performance at various conditions for practical applications.

A conventionally cast CoNiFeMn0.5Cr1.5 alloy and two versions with 0.25C&amp;3.7Ta or 0.25C&amp;3.7Hf were tested in oxidation at 1000°C for 50h with thermogravimetric recording of the oxidation kinetic. In all cases the obtained mass gain curves are parabolic. Their parabolic constants are much lower than the Kp previously determined for the original alloys with an equimolar base (CoNiFeMnCr). However, the post–mortem exploitation of the oxidized samples revealed analogous oxidation features on surface and subsurface, with here too external oxide strata on surface with different Mn and Cr contents, and rather great Mn–depletion in addition to a moderate Cr–depletion, in subsurface. Globally, the oxidation behavior is significantly better than earlier observed for the equimolar version of these alloys.

Nature provides plenty of good examples for simple and very efficient joint assemblies. One example is the enormously flexible cervical spine of American barn owls, which consists of 14 cervical vertebrae. Each pair of vertebrae produces a comparatively small individual movement in order to provide a large overall movement of the entire cervical spine. The biomimetic replication of such joints is difficult due to the delicate and geometric unrestricted joint shapes as well as the muscles that have to be mimicked. Using X-ray as well as micro computed tomography images and with the utilisation of additive manufacturing, it is possible to produce the owl neck vertebrae in scaled-up form, to analyse them and then to transfer them into technically usable joint assemblies. The muscle substitution of these joints is realised by smart materials actuators in the form of shape memory alloy wire actuators. This actuator technology is outstanding for its muscle-like movement and for its enormous energy density [1,2]. The disadvantage of this wire actuator technology is the low rate of contraction, which means that a large length of wire has to be installed to generate adequate movement. For this reason, the actuator wires are integrated into additively manufactured carrier components to mimic the biological joints. This results in joint designs that compensate for the disadvantages of the small contraction of the actuators by intelligently installing large wire lengths on comparatively small installation spaces, while also providing a sufficient force output. With the help of a test rig, the developed technical joint variants are examined and evaluated. This demonstrates the technical applicability of this bionic joints.

We studied the effect of annealing and the applied magnetic field from 50 Oe to 20 kOe on the magneto-structural behavior of Ni2FeSi-based Heusler microwires fabricated by using Taylor-Ulitovsky technique. Using the XRD analysis, a strong effect of annealing, manifested as the development of the crystallization process, was observed. The average grain size and crystalline phase content of annealed sample increase from 21.3 nm and 34 % to 32.8 nm and 79%, respectively, as-compared to the as-prepared one. In addition, upon annealing phase transforms into a monoclinic martensitic structure with modulation 10M were observed, which cannot be found in the as-prepared sample. Concerning the magnetic properties, both samples show ferromagnetic behavior below and above the room temperature, where the Curie temperature of Ni2FeSi is higher than room temperature. The induced secondary phases have a noticeable effect on the magnetic behavior of the annealed sample, where a high normalized saturation magnetization (NMs) and low normalized reduced remenance (Mr = M/M5K), compared to the as- prepared have been detected. Additionally, the coercivity of annealed sample shows one flipping point at 155 K where it behavior with temperature is changed. Meanwhile, the as-prepared sample show two flipped point at 205 K and 55 K. A mismatch between field cooling (FC) and field heating (FH) magnetization curves with temperature has been detected for annealed sample at low applied magnetic field. In addition the FC and FH curves shows different slopes with variation the temperature and the magnetic field. By increasing the external magnetic field higher than 200 Oe and up to 20 kOe a gradual changing in the magnetic behavior has been detected, where the mismatch and different slopes disappeared at applying magnetic field about 20 kOe. The difference in magnetic and structure behavior of Ni2FeSi microwires sample is discussed considering the effect of induced internal stresses by the presence of a glass coating and the recrystallization and stresses relaxation upon annealing.

The corrosion behavior of Fe-containing directionally solidified (DS) and centrifugally cast (CC) Al-Si-Cu-Zn alloys with either Co or Ni additions has been investigated. Electrochemical and immersion corrosion methods were used to investigate the corrosion behavior in 0.6 M NaCl after short (1-hour) and long (30-day) exposure periods. The employed solidification methods allowed the production of samples with a wide range of secondary dendrite arm spacing (SDAS) while preserving Si and Fe-containing phases. The 0.5 wt.% Ni and Co additions led to the growth of the AlFeSi(Ni) and AlFeSi(Co) phases, but no binary AlNi nor AlCo intermetallic par-ticles have been generated. Potentiodynamic polarization studies at early exposure revealed an increase in the corrosion potential as the Ni was added for either fast or slow solidified samples. The electrochemical impedance spectroscopy at early exposure demonstrated that the Ni-modified alloy, on the other hand, was associated to smaller charge transfer resistances, in-dicating a reduction in corrosion resistance after short elapsed time into the electrolyte. Howev-er, 30-day immersion tests revealed much lower corrosion rate of the Ni-modified alloy than the other alloys, while the corrosion rates of the Co-modified and non-modified alloys were simi-lar. In the Ni-containing alloy, decreased corrosion rate under long-term corrosion process was attributed to the formation of a thick and dense alumina layer, effectively protecting the surface under such conditions. This work contributes to a better knowledge of the corrosion behavior of Ni- and Co-corrected Al industrial scrap compositions.

This study aims to identify an optimal heat-treatment parameter set for an additively manufactured AlSi10Mg alloy in terms of increasing the hardness and eliminating the anisotropic microstructural characteristics of the alloy in as-built condition. Furthermore, the influence of these optimized parameters on the fatigue properties of the alloy investigated. In this respect, microstructural characteristics of an AlSi10Mg alloy manufactured by Laser-Based Powder Bed Fusion in non-heat-treated and heat-treated conditions were investigated. Their static and dynamic mechanical properties were evaluated, and fatigue behavior was explained by a detailed examination of fracture surfaces. Much of the microstructure in the non-heat-treated condition was composed of columnar grains oriented parallel to the build direction. Further analysis revealed a high fraction of pro-eutectic α-Al. Through heat-treatment, the alloy was successfully brought to its peak-hardened condition, while eliminating the anisotropic microstructural features. Yield strength and ductility increased simultaneously after heat-treatment, which is due to the relief of residual stresses, preservation of refined grains, and introduction of precipitation strengthening. The fatigue strength, calculated at 10^7 cycles, improved as well after heat-treatment and finally detailed fractography reviled that a more ductile fracture mechanism has happened in the heat-treated condition compared to the non-heat-treated condition.

The anodic polarization response of magnesium alloy AZ31 was characterized during exposure to aerated 0.1M NaCl solutions with millimolar additions of NaVO₃, Na₃PO₄, Na₂HPO₄, NaF and various pairings to assess their ability to inhibit corrosion kinetics and retard localized corrosion. Each of the candidate inhibitors reduced the corrosion rate of the alloy to some degree. A Na₃PO₄ - NaVO₃ pair produced a powerful inhibiting response decreasing the corrosion rate to about 10^-7 A/cm², which was two orders of magnitude lower than the uninhibited control case. A Bliss Independence assessment indicated that this inhibitor pair acted synergistically. A Na₂HPO₄ - NaVO₃ pair reduced the corrosion rate to 10^-6 A/cm² but was not assessed to be acting synergistically. The NaVO₃ - NaF pair did not reduce the corrosion rate significantly compared to the control case and was an antagonistic pairing. SEM imaging showed film formation due to exposure, which appears to be the origins of the observed inhibition. The resistance to localized corrosion was assessed as the difference in the breakdown potential and the corrosion potential with larger values indicating a lower probability of localized corrosion during free corrosion exposures. Effects of the inhibitors on this characteristic were mixed, but each of the inhibitor pairs yielded potential differences in excess of 100mV. A conceptual conversion coating process based on a mixture of vanadate and phosphate compounds were demonstrated. A fluoride-bearing formulation produced coatings whose total impedance was increased by a factor or 2 compared to an uncoated control. A fluoride-free formulation produced coatings whose corrosion resistance was increased by more than a factor of 3.

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

Myasthenia gravis (MG) is a disease characterized by typical clinical and immunopathogenic pe-culiarities, which correlate with age and sex/gender. Accordingly, MG patients show thymic al-terations and auto-antibodies productions, that can be the expression of a different pathogenetic mechanism related to age and gender. This determines, in relation to age at and sex/gender, a dif-ferent MG onset, prognosis, and outcome. Therefore, diverse MG forms can be identified, classi-fied, and characterized in relation to their different features, and precisely there are early onset and late-onset forms of MG. It has been hypothesized that the cause of appearance the two diverse forms of MG can be ascribed mainly to the diverse genetic and epigenetic factors. In this narrative review, we will analyze and discuss about the interplay of age- and sex-related factors (i.e. genet-ic and epigenetic factors) related to two different MG forms and how they contribute to their di-verse pathogenesis.

Calcium and magnesium are important not only for human health, but also for reducing problems related to the corrosive and aggressive effects of soft water on drinking water distribution materials. Experimental and mathematical modeling of the recarbonization process aimed at increasing the content of these biogenic elements in water was carried out using the novelty of a continuous laboratory and pilot scale fluidized bed reactors. Water remineralization using half-calcined dolomite (HCD) and carbon dioxide was used. The influence of operating conditions Q(CO2), freshwater inflow and HCD dose on quality indicators of treated drinking water (c(Ca2+), c(Mg2+), c(Ca2++Mg2+) and Ca/Mg) was studied. The results show that the concentration of Mg2+ is more significantly affected by the amount of HCD in the system and the flow of CO2. The influence of freshwater inflow on the Mg2+content is to a lesser extent. At a constant CO2 flow, therefore, as the tap water inflow increases, the Ca2+ content decreases and the Mg2+ content increases, which has results in a decrease in the Ca/Mg molar ratio. However, the Ca/Mg ratio can be effectively controlled by adding an appropriate amount of HCD at certain time intervals. Overproduction of ions is easily controlled by CO2 flow.

According to research, we have learned that Mg and TiO2 are new types material of marine protective coatings. We found that the addition of Mg can improve the performance of Zn-Al coating passivation film, and TiO2 has excellent photocatalytic self-cleaning performance. In this paper Zn-Al pseudo alloy coating was prepared by cold spray technique, and Zn-Al-Mg-TiO2 pseudo alloy composite coating was prepared by adding Mg and nano-TiO2. The effects of Mg and TiO2 to the marine protective properties of Zn-Al coatings were studied by friction and wear test, dynamic salt water corrosion test, electrochemical test, scanning electron microscope(SEM), energy dispersive spectrometer(EDS) and super deep scene 3D microscope. The results show that the addition of Mg and nano-TiO2 not only fills the gap of the coating and improves the density of the coating, but also generates grid-like flocculent corrosion products on the surface of the coating which can gather other corrosion products to improve the density of corrosion products, reduce the friction coefficient and corrosion rate of the coating surface, effectively prevent the invasion of Cl- in solution, and improve the wear and corrosion resistance of the coating.

There has been controversy around the mechanical properties of Mg-alloys such as AZ91D and the large variation of these have been seen. The current paper addresses this controversy through specially fabricated samples combined with tensile testing and advanced metallography, including 3D reconstruction of the phases. The results show that despite a more brittle nature of the fracture, the equiaxed microstructure displays a better elongation as compared to a dendritic microstructure. The main conclusion is that this is primarily caused by the nature, or tortuosity, of the Mg17Al12-network in the material.

Al-Zn-Mg-Cu alloy has high specific strength, good corrosion resistance, fracture toughness and fatigue resistance. It is one of the most important structural materials in the fields of aviation, aerospace, weapons, transportation and so on, which plays a huge role in the field of aerospace.In order to optimize the strength, toughness and corrosion properties of Al-Zn-Mg-Cu alloy, alloying has always been the focus of research on Al-Zn-Mg-Cu alloy. The effects of main alloying elements, trace alloying elements and rare earth elements on the microstructure and properties of Al-Zn-Mg-Cu aluminum alloy were briefly introduced in the paper, and the future research directions were prospected.

Understanding of the decisive role of the interaction mechanism and kinetics in the combustion processes is highly relevant for the elaboration of optimal conditions for obtaining Mo-Cu composite powders. From this perspective, the efficient delivery of the reduction mechanism of copper and molybdenum oxides with combined Mg + C reducing agents at high heating rates is crucial to develop a valuable approach for the combustion synthesis of Mo-Cu composite powders. Herein, we shed light on the mechanism of the reactions in all the studied binary, ternary and quaternary systems contemporaneously demonstrating the effect of the heating rate on the conversion degree. The combination of two highly exothermic and speedy reactions (MoO3+3Mg and CuO+Mg vs MoO3+CuO+4Mg) led to a slow interaction with weak self-heating (dysynergistic effect) due to a change in the reaction mechanism. On the other hand, it has been shown that during the simultaneous utilization of the Mg and C reducing agents, the process begins exclusively with carbothermic reduction, and at relatively high temperatures it continues with magnesiothermic one. The effective activation energy values of the magnesiothermic stages of the studied reactions were determined by Kissinger isoconversional method.

Statistical analysis of mechanical properties of thin-walled samples (~500 microns) obtained by selective laser melting from AlSi10Mg material and subjected to heat treatment for 1 hour at temperatures from 260 °C to 440 °C (step of aging temperature change 30 °C) has shown that the maximum strain hardening in the stretching diagram section from yield strength to tensile strength is achieved at the heat treatment temperature equal to 290 °C. At carrying out of correlation analysis statistically significant positive correlation between deformation corresponding to yield strength and the sum of heights of the largest protrusions and depths of the largest depressions of the surface roughness profile within the basic length of the sample (Rz) and the full height of the surface roughness profile (Rmax) was established. It was found that the reason for the correlation is the presence of cohesive states between the extreme values of the surface roughness profile that persist along the entire length of the specimen.

Precipitates are the primary source of strength for the Al-Mg-Si alloy. Aluminum alloy in the peak-aged state mainly contain β'' and β' precipitates. In the past, most of the literature only considered the strengthening effect of β''. Here we develop a single crystal intensity model including both precipitate enhancement effects for the first time. This model was subsequently implemented into a crystal plastic finite element method to model the uniaxial tensile process of a polycrystalline aggregate model of Al-Mg-Si alloy. The simulation results for uniaxial stretching are in good agreement with the experimental results, confirming that the constitutive parameters used for the single crystal strength model with two precipitates are based on realistic physical implications. Furthermore, by comparing the uniaxial tensile simulation results of a peak-aged alloy considering the actual precipitated phase composition of the alloy with those assuming that the precipitated phase is only the β'' phase, the predicted tensile strength of the former is around 5.65% lower than that of the latter, suggesting that the two kinds of precipitation should be considered separately when simulating the mechanical response of Al-Mg-Si alloy. It is highly expected that the present simulation strategy is not limited to the Al-Mg-Si alloys, and it can be equally applied to the other age-enhanced alloys.

A CoCrFeNiNb0.65 eutectic high-entropy alloys (EHEAs) prepared by arc melting were irradiated with a 100 keV He+ ion beam. Swelling, helium bubbles and mechanical response induced by irradiation were evaluated. When the ion fluence reached 1.0×1018 ions/cm2, the irradiation-induced swelling occurred on the sample surface, and as the ion fluence increasing, the swelling became increasingly severe and the surface of Nb-rich phase appeared peeling and shedding. Meanwhile, along the boundaries of matrix and Nb-rich phase there was a neat line of helium bubbles. The size of these helium bubbles decreased with distance from the center of the helium bubble layer. This result indicated that the phase boundaries were favorable sites for the nucleation and gathering of helium bubbles. Nanoindentaion results indicated that hardening and softening induced by He+ ion irradiation occurred in various ion fluences. At ion fluence of 5.0×1017 ions/cm2, the CoCrFeNiNb0.65 EHEAs exhibited an obvious hardening behavior, which can be explained by dislocation-dominated hardening effect. When the ion fluence reached 1.0×1018 ions/cm2 and 2.0×1018 ions/cm2, the hardening effect decreased probably due to the helium bubble aggregation and growth, as well as helium bubbles induced noncompact structures. The results of this study provide insights into the effect of helium bubbles on mechanical evolution and pave the way for designing EHEAs suitable for the nuclear industry.

The present study illustrates the strong effect of geometrical parameters on the magneto-structural properties of Co2MnSi glass-coated microwires prepared using the Taylor-Ulitovsky method. Thus, two samples with different geometrical aspect ratios (ρ= d / D) have been fabricated, where d is the metallic nuclei diameter and D is the total diameter of the Co2MnSi microwire. The XRD analysis shows a significant change by modifying the aspect ratio, for ρ = 0.46 the main peak with miller indices (220) is recognized as an A2-type disordered cubic structure. Meanwhile, in the sample with a low aspect ratio, ρ = 0.31, the perfect L21 ordered cubic structure is attained. In addition, a decrease in average grain size from 36.62 nm to 28.07 nm by increasing the aspect ratio from 0.46 to 0.31 is observed. The magnetic characterization has been done in a wide range of temperatures and magnetic fields. Both of Co2MnSi samples show ferromagnetic behavior in a whole measuring temperatures range. A significant increase in coercivity and normalized reduced remanence by decreasing the aspect ratio is observed. The change in the magnetic properties is attributed to the modification in the microstructure, which is induced during the fabrication process. Such a dependence on the microstructure and magnetic properties on the ρ-ratio can be associated either with the internal stresses distribution and magnitude or with different quenching rates of microwires with different aspect ratios. The current findings demonstrate the tunability of microstructure and magnetic properties of Co2MnSi-glass-coated microwires simply, by a small modification in the geometric properties during the manufacturing process and without excreting any additional post-processing. The variation in geometric parameters of Co2MnSi glass-coated microwires allows us to tune magnetic properties and structure, which is essentially advantageous for sensing devices development.

The cast defects strongly degrade the mechanical properties in cast alloys. The effect of Sn addition on Al-Si alloys was investigated by 3D computed tomography, SEM and TEM. Amorphous Sn oxides are found near the alumina film, cause more shrinkage pores, initiate cracks and deteriorate mechanical properties. This work suggests not adding Sn in various Al alloys used in cast state.

Ultra-high temperature oxidation-resistant alloys (UTORAs) have received a lot of attention due to the increased research demand for deep space exploration around the world. But UTORAs have the disadvantages of easy oxidation and chalking. So, in this study, a UTORA was prepared by hot-press sintering on VZrHfNbTa (HEA) substrate coated with hafnium. The bonding mechanism, resistance to high-temperature oxidation, and hardness of the sample tests were carried out. The results show that zirconium in the matrix will diffuse into the hafnium coating during the high-temperature sintering process and form the HfZr alloy transition layer, the coating thickness of the composite is about 120 μm, and the diffusion distance of zirconium in the hafnium coating is about 60 μm, this transition layer chemically combines the hafnium coating and the HEA substrate into a monolithic alloy composite. The results of high-temperature oxidation experiments show that the oxidation degree of the hafnium-coated VZrHfNbTa composite material was significantly lower than that of the VZrHfNbTa HEA after oxidation in air at 1600 °C for 5 h. The weight gain of the coated sample after oxidation is 56.56 mg/cm2, which was only 57.7 % compared to the weight gain of the uncoated sample (98.09 mg/cm2 for uncoated), and the surface of the uncoated HEA showed obvious dents, oxidation, and pulverization occurred on the surface and interior of the sample. In contrast, the coated composite alloy sample mainly underwent surface oxidation sintering to form a dense HfO2 protective layer, and the internal oxidation of the hafnium-coated VZrHfNbTa composite alloy was significantly lower than that of the uncoated VZrHfNbTa HEA.

In current work, we illustrate the effect of adding small amount of Carbon to very common Co2MnSi Heusler alloy based-glass coated microwires. A significant change in the magnetic and structure structural properties has observed for the new alloy Co2MnSiC compared to the Co2MnSi alloy. The magneto-structural investigations have performed to clarify the main phys-ical parameters i.e., structural & magnetic at a wide range of measuring temperature. The XRD analysis illustrated the well-defined crystalline structure with average grain size (Dg = 29.16 nm) and a uniform cubic structure with A2-type compared to the mixed L21 and B2 cubic structures for Co2MnSi-based glass coated microwires. The magnetic behaviour has investigated at a tem-perature range (5 to 300 K) and an external applied magnetic field (50 Oe to 20 kOe). The adding of small amount of Carbon to the Co2MnSi matrix enhance the magnetic thermal stability, where the thermomagnetic behaviour of Co2MnSiC glass-coated microwires show a perfect stable be-haviour for a temperature range from 300 K to 5 k, the differences between the coercivity value is only 0.3 Oe compared to 4 Oe for Co2MnSi-sample. In addition, M-H loops measured at tempera-ture below 50 K show unsaturated loops; meanwhile the Co2MnSi loops shows a strong antifer-romagnetic coupling for the loops measured below 50 K. By studying the field cooling (FC) and field heating (FH) magnetizations curves at a wide range of external applied magnetic field we detected a critical magnetic field (H = 1 kOe) where FC and FH curves have a stable magnetic behavior for Co2MnSiC sample, such stability does not find in Co2MnSi sample. We proposed a phenomenal expression to estimate the magnetization thermal stability, ΔM (%), of FC and FH magnetization curves and the maximum value is detected at the critical magnetic field where ΔM (%) ≈ 98 %. The promising magnetic stability of Co2MnSiC glass-coated microwires with tem-perature is due to the changing of the microstructure induced by adding Carbon, as the A2-type structure show a unique stability by variation the temperature and the external magnetic field. In addition, a unique internal mechanical stress, which induced during the fabrication process and plays on controlling magnetic behavior with temperature and external magnetic field. The ob-tained results make Co2MnSiC promising candidate for magnetic sensing devices based Heusler glass-coated microwires.

The present work was aimed at the investigation of effect of High Energy Ball Milling (HEBM) time on the sintering kinetics, structure, and properties of heavy tungsten alloy (HTA) W-7%Ni-3%Fe. The HTA samples were obtained from the nanopowders (20-80 nm) by conventional liquid phase sintering (LPS) in hydrogen and by Spark Plasma Sintering (SPS) in vacuum. The HTA density was shown to depend on the HEBM time non-monotonously that originates from the formation of non-equilibrium solid solutions in the W-Ni-Fe systems during HEBM. The SPS kinetics of the HTA nanopowders was shown to have a two-stage character, the intensity of which depends on the Coble diffusion creep rate and on the intensity of diffusion of the tungsten atoms in the crystal lattice of the -phase. The kinetics of sintering of the initial submicron powders have a single-stage character originating from the intensity of the grain boundary diffusion in the -phase. The dependencies of the hardness and of the yield strength on the grain sizes were found to obey the Hall-Petch relation. The hardness, strength, and dynamic strength in the compression tests of the fine-grained tungsten alloys obtained by SPS and LPS were studied.

The importance of both recycling and additive manufacturing (AM) is increasing, however there has been a limited focus on development of AM alloys that are recyclably compatible with the larger scrap loops of wrought 5xxx, 6xxx and cast 3xx aluminium alloys. In this work the powder bed fusion (PBF) printability of AlMgSi alloys in the interval of 0-30wt%Mg and 0-4wt%Si is screened experimentally with a high throughput method. This method produces PBF mimicked material by PVD co-sputtering followed by laser remelting. Strong evidence was found for AlMgSi alloys being printable in two different composition ranges; Si+Mg<0.7wt% or for Si+2/3Mg>4wt% when Mg < 3wt% and Si > 3wt%. Increasing the amount of Mg and Si influence the grain structure by introducing fine columnar grains at the melt pool boundary, although the melt pool interior was unaffected. Hardness in as-built state increased with both Mg and Si, alt-hough Si had neglectable effect at low levels of Mg. Both evaporative loss of Mg and the amount of Mg in solid solution increased linearly with the amount of Mg.

In current study we have obtained Co2FeSi-glass coated microwires with different geometrical aspect ratio, ρ = d/Dtot (diameter of metallic nucleus, d and total diameter, Dtot). The structure and magnetic properties are investigated at a wide range of temperature. XRD analysis illustrates a notable changing in the microstructure by increasing the aspect ratio of Co2FeSi glass coated microwires. Amorphous structure is detected for the sample with the lowest aspect ratio (ρ = 0.23), whereas a growth of crystalline structure is observed in the other samples (aspect ratio ρ = 0.30 and 0.43). This change at the microstructure properties correlates with dramatic changing in magnetic properties. For the sample with the lowest ρ -ratio, non-perfect square loops are obtained with low normalized remanent magnetization. A notable enhancement in the squareness and coercivity are obtained by increasing ρ -ratio. Changing the internal stresses strongly affects the microstructure, resulting in a complex magnetic reversal process. The thermomagnetic curves show large irreversibility for the Co2FeSi with low ρ -ratio. Meanwhile, if we increase the ρ -ratio, the sample shows perfect ferromagnetic behavior without irreversibility. The current result illustrates the ability to control the microstructure and magnetic properties of Co2FeSi-glass-coated microwires by changing only their geometric properties without performing any addition heat treatment. The modification of geometric parameters of Co2FeSi glass-coated microwires allows to obtain microwires which exhibit an unusual magnetization behavior that offers opportunities to understand the phenomena of various types of magnetic domain structures, which is essentially helpful for designing sensing devices based on thermal magnetization switching.

In this study, we demonstrate how the incorporation of appropriate feature engineering together with the selection of a Machine Learning (ML) algorithm that best suits the available dataset, leads to the development of a predictive model for transformation temperatures that can be applied to a wide range of shape memory alloys. We develop a gradient boosting ML surrogate model capable of predicting Martensite Start, Martensite Finish, Austenite Start, and Austenite Finish transformation temperatures with an average accuracy of more than 95% by explicitly taking care of potential distribution changes when modeling different alloy systems. We included heat treatment, rolling, extrusion processing parameters, and alloy system categorical features in the model input features to achieve more accurate and realistic results. In addition, using Shapley values, which are calculated based on the average marginal contribution of features to all possible coalitions, this study was able to gain insights into the governing features and their effect on predicted transformation temperatures, providing a unique opportunity to examine the critical parameters and features in martensite transformation temperatures.

The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC crystal structure was additively manufactured with a selective laser melting (SLM) process starting from mechanically alloyed powders. The as produced alloy shows finenitride and  phase pre-cipitates, which are Cr-rich and stable up to about 900 K. The precipitates increase in number and dimensions after long-period annealing at 900-1300 K, with a change in the HEA mechanical properties. Higher aging temperatures in furnace, above 1300 K, turn the alloy in a single FCC structure, with disappearance of the nitrate and  phase precipitates inside the grains and at the grain boundaries, but with still a presence of a finer Cr-rich nitride precipitation phase. These re-sults suggest that the as-produced HEA is a supersatured solid solution at low and intermediate temperature with nitrides and  nanostructures.

The design of processing routes involving the presence of the liquid phase is mainly associated with the knowledge of its surface and transport properties. Despite this need, due to experimental difficulties related to high temperature measurements of metallic melts, for many alloy systems neither thermodynamic nor thermophysical properties data are available. A good example lacking these datasets represents the Ir-Si system, although over the last fifty years, the structures and properties of its solid phases have been widely investigated. To compensate the missing data, the Gibbs free energy of mixing of the Ir-Si liquid phase was calculated combining the model predicted values for the enthalpy and entropy of mixing using Miedema’s model and Free Volume Theory, respectively. Subsequently, in the framework of statistical mechanics and thermodynamics, the surface properties were calculated using the Quasi Chemical Approximation (QCA) for the regular solution, while to obtain the viscosity, the Moelwyn-Hughes (MH) and Terzieff models were applied. Subsequently, the predicted values of the abovementioned thermophysical properties were used to model the non-reactive infiltration isotherm of Ir-Si (eutectic) / SiC system.

Traditional refractory materials such as nickel-based superalloys have been gradually unable to meet the performance requirements of advanced materials. The Mo-Si-based alloy, as a new type of high temperature structural material, has entered the vision of researchers due to its charming high temperature performance characteristics. However, its easy oxidation and even "pesting oxidation" at medium temperatures limit its further applications. In order to solve this problem, researchers have conducted large numbers of experiments and made breakthrough achievements. Based on these research results, the effects of rare earth elements like La, Hf, Ce and Y on the microstructure and oxidation behavior of Mo-Si-based alloys were systematically reviewed in the current work. Meanwhile, this paper also provided an analysis about the strengthening mechanism of rare earth elements on the oxidation behavior for Mo-Si-based alloys after discussing the oxidation process. Furthermore, the research focus about the oxidation protection of Mo-Si-based alloys in the future was prospected to expand the application field.

This article discuss the effects of heat treatment and lubrication modes on the machinability of an A356 alloy (Al-Si-Mg); the alloy is studied as-received, with solution heat-treated alloy (SHT) as well as with an alloy that is solution heat-treated and then aged at 155, 180 and 220 °C. In the course of machinability evaluation, several criteria including cutting force, surface roughness, tool wears and burr analysis (chip) were studied. The results and analysis in this work indicated that the selected machinability criteria are important and necessary to effectively evaluate the machinability of A356 alloys. The machinability of both materials and tools were estimated in terms of cutting force, chip thickness ratio and burr formation, flank wear and roughness. The effects of different cutting parameters (cutting speed and feed rate) and lubrication modes (dry, mist and wet) on the machinability of the A356 cast alloy were also examined. The influence of heat treatments on the burr formation and surface quality was clearly revealed by the experimental results. Experimental work revealed that cutting forces were influenced significantly by aging and cutting speed. However, the different aging at 155, 180, and 220 °C and the cutting speed significantly affected the machinability of the A356 cast alloy. The results obtained show that a better drilling performance in terms of surface quality occurs at a high feed rate, with dry drilling and artificial aging at T6.

Welding of dissimilar aluminium alloys has been a challenge for a long period until the discovery of the solid state welding technique called friction stir welding (FSW). The discovery of this technique encouraged different research interests revolving around the optimization of this technique. This involves the welding parameters optimization and this optimization is categorized into two classes i.e. similar alloys and dissimilar alloys. This paper reports about the mechanical properties of the friction stir welded dissimilar AA1050-H14 and AA5083-H111 joint. The main focus is to compare the mechanical properties of specimens extracted from different locations of the welds i.e. the beginning, middle and the end of the weld. The specimen extracted at the beginning of the weld showed low tensile properties compared to specimens extracted from different locations of the weld. There was no certain trend noted through the bending results. All three specimens showed dimpled fracture which is the characterization of the ductile fracture.

The Ni-Co-Cr-W-Mo system is critical for the design of nickel-based super-alloys. This system stabilizes different topologically close packed (TCP) phases in many of the commercially super-alloys with high W and Mo contents. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and thermodynamic calculations are applied to investigate the thermodynamics of the precipitates in two different W content Ni-Co-Cr-W-Mo super-alloys. Computational thermodynamics verified experimental observation of the f u phase formation as a function of temperature and alloy chemistry, but the kinetics for the precipitation of M6C phase do not agree with the experimental findings. The major precipitates of alloy 1 at temperatures 700 and 750 °C during long time exposure are M23C6, γ′ phase, and MC, and alloy 2 are M23C6, γ′ phase, MC, M6C and u phase. The W addition is found to promote the precipitation of M6C and u phase during exposure. The M6C has higher W and lower Ni content than that of u phase, meanwhile, M6C is an unstable phase would transform into M12C after 5000 h exposure at 750 °C. A great quantity of needle-like u phases precipitated after exposure at 750 °C for 5000h, which have no effect on the impact property of alloy 2.