Density functional theory (DFT) and coupled cluster theory (CCSD(T)) calculations are performed to investigate the geometric, electronic structures and chemical bonding of a series of Cu-doped zinc oxide clusters, CunZn3O3 (n = 1-4). The structural evolution of CunZn3O3 (n = 1-4) clusters are elaborated in our work. The planar seven-membered ring of CuZn3O3 cluster plays an important role in the structural evolution, that is, the Cu atom, Cu dimer (Cu2) and Cu trimer (Cu3) anchor on the CuZn3O3 cluster. The aggregate behavior of Cu atoms on Zn3O3 may offer insight into the study of Cu/ZnO-based catalysts. Additionally, it is found that the CunZn3O3 clusters become more stable as the Cu content (n) increases. Bader charge analysis points out that as the Cu atoms doping, the reducibility of Cu aggregation (Cun-1) on the CuZn3O3 cluster increases. Combined with the d-band centers and the surface electrostatic potential (ESP), the reactivity and the possible reaction sites of CunZn3O3 (n = 1-4) clusters are also illustrated.

The electrical and optical properties of sol-gel derived aluminum-doped0 zinc oxide thin films containing 2 at.% Al were investigated considering the modifying effects of 1) increasing the sol H₂O content; and 2) thermal treatment procedure with high-temperature approach followed by an additional heat-treatment step under a reducing atmosphere. According to the results obtained via the TG-DTA analysis, FT-IR spectroscopy, X-ray diffraction technique and four-point probe resistivity measurement, it is argued that the sol hydrolysis, decomposition of the deposited gel and crystallization of grains result in grains of larger crystallite size and stronger c-axis preferred orientation with slightly less microstrain in the modified sample. The consequent morphology and grain-boundary characteristics turn out as improved conductivity, implying higher values of concentration and mobility of charge carriers. A detailed investigation on samples optical properties, in terms of analyzing their absorption and dispersion behaviors through the UV-Vis-NIR spectroscopy, support our reasoning for the increase of the mobility, and to a lesser extent, the concentration of charge carriers, while causing only a slight degradation of optical transmission. Hence, an enhanced performance as a transparent conducting film is claimed for the modified sample by comparing the figure-of-merit values.

Millions of people worldwide are affected by diabetes, a chronic disease that continuously grows due to abnormal glucose concentration levels present in the blood. Monitoring blood glucose concentrations is therefore an essential diabetes indicator to aid in the management of the disease. Enzymatic electrochemical glucose sensors presently account for the bulk of glucose sensors in the market. However, their disadvantages are that they are expensive and are dependent on environmental conditions, hence affecting their performance and sensitivity. To meet the increasing demand, non-enzymatic glucose sensors based on chemically modified electrodes for the direct electrocatalytic oxidation of glucose are a good alternative to the costly enzymatic-based sensors currently on the market, and the research thereof continues to grow. Nanotechnology-based biosensors have been explored for their electronic and mechanical properties, resulting in enhanced biological signalling through the direct oxidation of glucose. Copper oxide and copper sulfide exhibit attractive attributes for sensor application, due to their non-toxic nature, abundance, and their unique properties. Thus, in this review, copper oxide and copper sulfide-based materials, are evaluated based on their chemical structure, morphology, and fast electron mobility as suitable electrode materials for non-enzymatic glucose sensors. The review highlights the present challenges of non-enzymatic glucose sensors that have limited their deployment into the market.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

The nitrogen-doped amorphous oxide semiconductor (AOS) thin film transistors (TFTs) with double-stacked channel layers (DSCL) were prepared and characterized. The DSCL structure composed of nitrogen-doped amorphous InGaZnO and InZnO films (a-IGZO:N/a-IZO:N or a-IZO:N/a-IGZO:N) made the corresponding TFT devices exhibit quite large field-effect mobility due to the existence of double conduction channels. Especially, the a-IZO:N/a-IGZO:N TFTs showed even better electrical performance (μ_FE = 15.0 cm²·V^-1·s^-1, SS = 0.5 V/dec, V_TH = 1.5 V, I_ON/I_OFF = 1.1×10⁸) and stability (V_TH shift of 1.5, -0.5, and -2.5 V for positive bias-stress, negative bias-stress and thermal stress tests, respectively) than the a-IGZO:N/a-IZO:N TFTs. Based on the X-ray photoemission spectroscopy measurements and energy band analysis, it was assumed that the optimized interface trap states, the less ambient gas adsorption, and the better suppression of oxygen vacancies in the a-IZO:N/a-IGZO:N hetero-structures might be responsible for the better behaviors of the corresponding TFTs.

The electrochemical CO2 reduction reaction can lead to high value-added molecules production while helping decrease anthropogenic CO2 emissions. Copper can reduce CO2 to more than thirty different hydrocarbons and oxygenates, but it lacks the required selectivity. We present a computational investigation of the role of nano-structuring and alloying in Cu-based catalysts on the activity and selectivity of CO2 reduction to one-carbon products: carbon monoxide, formic acid, formaldehyde, methanol, and methane. The adsorption, activation, and conversion of CO2 were computed on monometallic and bimetallic (decorated and core-shell) 55-atom Cu-based clusters. The dopant metals considered were Ag, Cd, Pd, Pt, and Zn, located at different coordination sites. The relative binding strength of the intermediates at different applied potentials were used to identify the optimal catalyst for the selective CO2 conversion to one carbon products. It was discovered that single atom doping with Cd and Zn is optimal for the CO2 to carbon monoxide conversion. The core-shell models with Ag, Pd, and Pt provided higher selectivity for formic acid and formaldehyde. The Cu-Pt and Cu-Pd showed lowest overpotential for methane formation.

Many stable water dispersions of various chemical compositions containing bioactive chemical compounds: copper silicate, titanium dioxide and zinc oxide (and other auxiliary substances) were developed and fabricated - they were used for preparation of thin hybrid coatings having very good antimicrobial properties against gram negative bacteria (Escherichia coli), gram positive bacteria (Staphylococcus aureus) and yeast fungus (Candida albicans). Polyester (PES) nonwovens were modified by dip-coating, and PES and cotton fabrics - by dip-coating and coating methods.

Copper oxide nanoparticles (CuONPs) were synthesized using an eco-friendly method and their antimicrobial and biocompatibility properties were determined. The supernatant and extract of the fungus Ganoderma sessile yielded small, quasi-spherical NPs with an average size of 4.5 ± 1.9 nm and 5.2 ± 2.1 nm, respectively. CuONPs showed antimicrobial activity against Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa. Minimum inhibitory concentration (MIC) for E. coli and S. aureus was 15.9 µg/mL for nanoparticles (NPs) using the supernatant (CuONPs-S) and 16.5 µg/ml for NPs using the extract (CuONPs-E). Lower concentrations were required for P. aeruginosa inhibition. Ultrastructural analysis revealed the presence of the small CuONPs all through the bacterial cells. Finally, the toxicity of CuONPs was analyzed in three mammalian cell lines: hepatocytes (AML-12), macrophages (RAW 264.7) and kidney (MDCK). Low concentrations (<15 µg/ml) of CuONPs-E were non-toxic to kidney cells and macrophages, and the hepatocytes were the most susceptible to CuONPs-S. The results obtained suggest that the CuONPs synthesized using the extract of the fungus G. sessile, could be further evaluated for the treatment of superficial infectious diseases.

Measurements of copper and zinc in transfusion-dependent thalassemia (TDT) show contradictory results.Aim of the study: To examine serum levels of these minerals in TDT in relation to iron overload indices and erythron variables. Methods: This study recruited 60 children with TDT and 30 healthy children aged 3-12 years old.Results: Zinc was significantly higher in TDT children than in control children, whilst copper and the copper to zinc ratio were significantly lowered in TDT. Serum zinc was significantly associated with the number of blood transfusions and iron overload variables (including serum iron and TS%) and negatively with erythron variables (including hemoglobin, mean corpuscular volume, mean corpuscular hemoglobin). Serum copper was significantly and negatively associated with the same iron overload and erythron variables. The copper to zinc ratio was significantly correlated with iron, TS%, ferritin, hemoglobin, mean corpuscular volume, and mean corpuscular hemoglobin. Albumin levels were significantly higher in TDT children than in control children. Conclusion: Our results suggest that the increase in zinc in children with TDT may be explained by iron loading anemia and hemolysis and the consequent shedding of high amounts of intracellular zinc into the plasma. Increased albumin levels and treatment with Desferral may further contribute towards higher zinc levels in TDT. We suggest that the elevations in zinc in TDT are a compensatory mechanism protecting against infection, inflammation, and oxidative stress. Previous proposals for prophylactic use of zinc supplements in TDT may not be warranted.

Sickle cell disease (SCD) is an inherited disorder of major health challenge in Nigeria. Micronutrients deficiencies often associated with the disorder may cause inflammation and abnormal metabolisms in the body. The copper-to-zinc ratio is a more important assessment than the concentrations of either of the metals in clinical practice. This study seeks to evaluate serum levels of c-reactive protein (CRP), copper, zinc and copper-to-zinc ratio and to correlate copper-to-zinc ratio with CRP in adult subjects with SCD. Serum copper, zinc, CRP and plasma fibrinogen were assayed in 100 confirmed SCD patients in steady clinical state and 100 age and sex matched subjects with normal haemoglobin. Serum copper and zinc were assayed by colorimetric method using reagents supplied by Centronic, Germany while CRP and fibrinogen were assayed using reagents supplied by Sigma (St. Louis, MO, USA) and Anogen (Ontario, Canada), respectively. The copper to zinc ratio was calculated from serum levels of copper and zinc. The measured parameters were compared between the groups using Students t-test and Pearson correlation coefficient was used to relate CRP with the other parameters. Serum copper, CRP, fibrinogen and copper-to-zinc ratio were significantly higher (p < 0.001) while zinc level was lower in SCD patients than controls. Serum CRP concentration correlated with copper (r = 0.10; p < 0.02), zinc (r = −0.199; p < 0.05) and Copper-to-zinc ratio (r = 0.312; p < 0.002) but the correlation between CRP and fibrinogen was not significant. Inflammatory condition may modulate copper and zinc homeostasis and copper-to-zinc ratio may be used as marker of nutritional deficiency and inflammation in SCD patients.

Copper(II), nickel(II) and zinc(II) complexes of various peptide fragments of tau protein were studied by potentiometric and spectroscopic techniques. All peptides contained one histidyl residue and represented the sequences of tau(91-97) (Ac-AQPHTEI-NH2), tau(385-390) (Ac-KTDHGA-NH2) and tau(404-409) (Ac-SPRHLS-NH2). Imidazole-N donors of histidine were the primary metal binding sites for all peptides and all metal ions but in case of copper(II) and nickel(II) the deprotonated amide groups were also involved in metal binding by increasing pH. The most stable complexes were formed with copper(II) ion but the presence of prolyl residues resulted in significant changes in the thermodynamic stability and speciation of the systems. It was also demonstrated that nickel(II) and especially zinc(II) complexes have relative low thermodynamic stability with these peptides. Copper(II) catalyzed oxidation of the peptides was also studied. In the presence of H2O2 the fragmentation of peptides can be detected in all cases. In the simultaneous presence of of H2O2 and ascorbic acid the extent of the fragmentation of the peptide is less preferred, and the formation of 2-oxo-histidine also occurs.

ZnO films with Ti atoms incorporated (TZO) in a wide range (0-18 at. %) have been grown by reactive co-sputtering on silicon and glass substrates. The influence of the titanium incorporation in the ZnO matrix on the structural and optical characteristics of the samples has been determined by Rutherford backscattering spectroscopy (RBS), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results indicate that the samples with low Ti content (< 4 at. %) exhibit the wurtzite-like structure, with the Ti+4 ions substitutionally incorporated into the ZnO structure, forming Ti-doped ZnO films. In particular, very low concentration of Ti (<0.9 at. %) leads to a significant increase of the crystallinity of the TZO samples. Higher Ti contents give rise to a progressive amorphization of the wurtzite-like structure so samples with high Ti content (≥18at. %), displays an amorphous structure indicating the XPS analysis a predominance of Ti-O-Zn mixed oxides. The energy gap, obtained from absorption spectrophotometry, increases from 3.2 eV for pure ZnO films to 3.6 eV for those with the highest Ti content. Ti incorporation in the ZnO samples below 0.9 at. % rises both, the blue (380 nm) and green (550 nm) bands of the photoluminescence (PL) emission, thereby indicating a significant improvement of PL efficiency of the samples.

The color of a thin copper oxide layer formed on a copper plate was transformed from reddish-brown into blue-purple by irradiation with 5 keV Ar+ ions to a fluence as low as 1 1015 Ar+ cm–2. In the unirradiated copper oxide layer, the copper valence state of Cu2+ as well as Cu+ and/or Cu0 was included as indicated by the presence of a shake-up satellite line in a photoemission spectrum. While for the irradiated one, the satellite line decreased in intensity, indicating that irradiation resulted in the reduction from Cu2+ to Cu+ and/or Cu0. Furthermore, nuclear reaction analysis using a 16O(d, p)17O reaction with 0.85 MeV deuterons revealed a significant loss of oxygen (51015 O atoms cm–2) in the irradiated layer. Thus, the chromatic change observed in the present work originated in the irradiation-induced reduction of a copper oxide.

Surface Plasmon Resonance (SPR) is an attracting property of certain transition metals when they are synthesized in nano-range giving rise to promising optical applications. However, most SPR and associated applications are limited to the noble metal nanoparticles, which limits their potential due to high production cost. We report surface plasmon resonance in copper-copper oxide core-shell quantum dots synthesized via chemical route studied by using UV-Visible spectrophotometry. Tuning of the plasmonic resonance with respect to the particle diameter is achieved by an inexpensive all chemical route. Photoluminescence measurements also support the data. This size reduction leads to remarkable changes in its optical response as compared to the bulk metal. The results point towards applications of these materials in tunable SPR based biosensors.

Micronutrient deficiencies are a major public health problem. Beans are an important plant-based source of iron, zinc and copper, but their absorption is reduced in the presence of anti-nutrients such as phytates, polyphenols and tannins. Soaking and discarding the soaking water before cooking is unanimously recommended, but this can result in mineral loss. Data on the consequences for mineral bioaccessibility is still limited. This study aimed to evaluate iron, zinc and copper bioaccessibility in black beans cooked (regular pan, pressure cooker) with and without the soaking water. Minerals were quantified by ICP-MS, myo-inositol phosphates (InsP₅, InsP₆) by HPLC ion-pair chromatography, total polyphenols using Folin-Denis reagent and condensed tannins using Vanillin assay. Mineral bioaccessibility was determined by in vitro digestion and dialysis. All treatments resulted in a statistically significant reduction of total polyphenols (30%) and condensed tannins (20%). Only when discarding the soaking water a loss of iron (6%) and copper (30%) was observed, and InsP₆ was slightly decreased (7%) in one treatment. Bioaccessibility of iron and zinc were low (about 0.2% iron and 35% zinc), but copper presented high bioaccessibility (about 70%). Cooking beans under pressure without discarding the soaking water resulted in the highest bioaccessibility levels among all household procedures. Discarding the soaking water before cooking did not improve the nutritional quality of the beans.

We report a self-assembly synthesis of silicon nanoparticles/nitrogen-doped reduced graphene oxide/ carbon nanofiber (Si@N-doped rGO/CNF) composites as potential high-performance anodes for rechargeable lithium-ion batteries (LIB) through the electrostatic attraction between amino and carboxyl groups. Nitrogen atoms generate a large number of vacancies or defects on the graphite plane, providing additional transmission channels for the diffusion of lithium ions, and improving the conductivity of the electrode. Carbon nanofiber (CNF) can help maintain the stability of the electrode structure and prevent silicon nanoparticles from falling off the electrode, prevent silicon nanoparticles from being directly exposed to the electrolyte, and can form a stable solid electrolyte interface (SEI) film. The three-dimensional conductive structure composed of Si, nitrogen atom-doped reduced graphene oxide (N-doped rGO), and CNF can effectively buffer the volume changes of silicon nanoparticles, shorten the transmission distance of lithium ions (Li+) and electrons, and make the electrode have good conductivity and stability in mechanical properties. In addition, compared with the Si@N-doped rGO and Si/rGO/CNF composite electrode, the Si@N-doped rGO/CNF composite electrode shows good cycle performance and rate capability, and its reversible specific capacity can reach 1418.8 mAh/g. The capacity retention rate is 64.7%, and the coulomb efficiency is 95%.

Gymnema sylvestre is a pharmacological plant which has a rich source of bioactive compounds specifically gymnemic acid (GA) and phenolic compounds (PC) that used for pharmaceutical industries. Sources for naturally occurring bioactive compounds are limited, due to geographical and seasonal variations; on the other hand, it is commercially in demand. Biosynthesis of G. sylvestre phytochemicals through in vitro culture often enhanced by elicitation. The use of cell suspension cultures (CSC) has interested serious attention on the production of essential phytochemicals. The current study is aimed at improving the contents of GA and PC in G. sylvestre CSC using the copper oxide nanoparticles (CuO NPs). Callus was obtained on MS medium with 2.0 mg/L 2,4-dichlorophenoxyacetic acid (2,4-D), 0.1 mg/L kinetin (KIN), phytoagar (8.0 g/L), and sucrose (30 g/L). The above medium devoid of agar was used for the initiation of CSC. The CSC was treated with three levels of CuO NPs (1, 3 or 5 mg/L) to enhance the production of GA and PC. The greatest amount of GA (89.25 mg/g dry cell mass, DCM), total phenolic (245.10 mg/g), and flavonoid (4.57 mg/g) in CSC were achieved when G. sylvestre cells were treated for 48 h with 3 mg/L CuO NPs. Also, the biomedical potential (antioxidant, antidiabetic, anti-inflammatory, antibacterial, antifungal and anticancer activities) were also high in the CuO NPs (3 mg/L) treated CSC extracts of G. sylvestre. CuO NPs elicitation of CSC significantly increased production of GA (9-fold), and PC than non-elicited CSC in G. sylvestre.

We present atomic structures and nonequilbrium synthesis of new class of materials, where the basic structural unit is a diamond tetrahedron. When units of one, two, and three tetrahedra are randomly packed, we create distinct phases of amorphous Q-carbon. Four tetrahedra in two adjacent layers lead to crystalline diamond lattice, which has four missing tetrahedra alternately. When these four missing tetrahedra are filled, we create subunit cell of crystalline Q-diamond. Theoretical calculations show that superconducting transition temperature (Tc) in 50 atomic % B-doped Q-diamond can reach near room temperature at ambient pressures. This is consistent with our earlier results using low-loss EELS measurements in 50 atomic % B-doped Q-carbon, which had mostly amorphous QB3 phase mixed with some crystalline Q-diamond phase. These EELS results showed that the Tc for these samples was in between 90K and 300K. Theoretical calculations of density of states, Eliashberg function, electron-phonon interaction parameter, and root-mean-square and logarithmic average of frequency in crystalline Q-diamond show Tc in the range of 268K to 300K, which is in a complete agreement with our EELS results in QB3.

Classical antibacterial drugs were designed to target specific bacterial properties distinct from host human cells to maximize potency and selectivity. These designs were quite effective as they could be easily derivatized to bear next generation drugs. However, the rapid mutation of bacteria and their associated acquired drug resistance have led to the rise of highly pathogenic superbug bacterial strains for which treatment with first line drugs is no match. More than ever, there is a dire need for antibacterial drug design that goes beyond conventional standards. Taking inspiration by the body’s innate immune response to employ its own supply of labile copper ions in a toxic attack against pathogenic bacteria, which have a very low Cu tolerance, this review article examines the feasibility of Cu-centric strategies for antibacterial preventative and therapeutic applications. Promising results are shown for the use of Cu-containing materials in the hospital setting to minimize patient bacterial infections. Studies directed at disrupting bacterial Cu regulatory pathways elucidate new drug targets that can enable toxic increase of Cu levels and perturb bacterial dependence on iron. Likewise, Cu intracellular chelation/prochelation strategies effectively induce bacterial Cu toxicity. Cu-based small molecules and nanoparticles demonstrate the importance of the Cu ions in their mechanism and display potential synergism with classical drugs.

Information taken from David A. Scott’s book “Copper and Bronze in Art” was crucial for research on copper corrosion products in Stuttgart. Examples discussed are the nature and variability of ‘Black Spots’ (aka ‘Brown Fuzzies’); cupric hydroxide by cleaning, patination, and pigment synthesis; the wondrous phenomenon of curly malachite; chalconatronite formed by contact to soda glass; the formation of copper formates by glass-induced metal corrosion; and synthesis and X-ray diffraction of basic copper acetates (‘verdigris’).

Wastewater contaminated with antibiotics is a major environmental challenge. We developed here the green synthesis of bio-graphenes by using natural precursors (Xanthan, Chitosan, Boswellia, Tragacanth). The use of these precursors can act as templates to create 3D doped graphene structures with special morphology. Also, this method is a simple method for in-situ synthesis of doped graphenes. The elements present in the natural polymers (N) and other elements in the natural composition (P, S) are easily placed in the graphene structure and improve the catalytic activity due to the structural defects, surface charges, increased electron transfers, and the high absorption. In this mechanism, O2 dissolved in water absorbs onto the positive charged C in doped graphenes to create oxygenated radicals, which enables the degradation of antibiotic molecules. Light irradiation increases the amounts of radicals and rate of antibiotic removal. The results have shown that the hollow cubic Chitosan-derived graphene has shown the best performance due to the doping of N, S, and P. The Boswellia-derived grapheme shows the highest surface area, but lower catalytic performance, which indicates the more effective role of doping in the catalytic activity. The effect of oxygen and light were also studied to accelerate the degradation process.

In this paper we propose a simple procedure to obtain multi-walled carbon nanotubes (MWCNT) decorated with TiO₂-Ag nanoparticles (MWCNT-TiO₂-Ag). MWCNT were decorated with TiO2-Ag via combined functionalisation with -OH and –COOH groups and polymer wrapping technique using poly(allylamine hydrochloride) (PAH). TiO₂ modified Ag nanoparticles were synthesized through Pechini method using mixture of acetylacetonate-modified titanium (IV) isopropoxide with silver nitrate (the Ag+/Ti4+ atomic ratio, is 0.5, 1,0, 1.5, 2.0 and 2.5 %, respectively) and the L(+)-ascorbic acid, as reducing agents. XRD analysis revealed the formation of nanocomposite containing CNT, TiO₂ (anatase and rutile) and Ag. By SEM was evidenced the presence of the nanoparticles on MWCNT surface. The increases of the ratio between Ag⁺ and Ti⁴⁺ decrease the band gap energy of the samples. In Raman spectra the characteristic vibration of the TiO₂, Ag and C atoms of graphite are identified. The photocatalytic activity of the MWCNT-TiO₂-Ag nanocomposite was assessed by examining the degradation of Allura red (E129) aqueous solution under UV irradiation. The dye photodegradation process follows a pseudo – first – order kinetic with respect to the Langmuir – Hinshelwood reaction mechanism.

The frequent occurrence of rib fractures in slaughtered lambs results in significant economic loss to producers and processors in South Australia and raises concerns about the welfare of the animals. The prevalence of rib fractures became evident through the Enhanced Abattoir Surveillance (EAS) program introduced in 2007. The present study aimed to investigate the association between rib fracture prevalence in lambs at slaughter and their nutrition and management on the farm of origin. The slaughter of 30,055 lambs from 60 farms was monitored at a South Australian abattoir in November 2016. Rib fracture prevalence was 4% (range 0 - 18% per consignment), with all consignments of more than 240 lambs having at least one with fractured ribs. Traceback investigation on 56 of the 60 farms suggests that rib fractures most probably occur during routine husbandry procedures and, based on soil mineral analysis, are associated with calcium inadequacy. There was substantial variation between lines of lambs from different farms, and factors contributing to the differences included line size, region, and soil characteristics, including available calcium. There is a need to modify sheep husbandry and management practices to improve sheep welfare and reduce the cost of rib fractures to the sheep industry.

Point-contact spectroscopy has been performed on bulk samples of electron-doped high temperature superconductor Nd2-xCexCuO4-. The samples were characterized by X-ray diffraction and scanning electron microscopy equipped with a wavelength dispersive spectrometer and an electron backscatter diffraction detector. The samples with a Ce content x = 0.15, show the absence of spurious phases and randomly oriented grains, most of which have dimensions of approximately 220 µm2. The low-bias spectra in the tunnelling regime, i.e., high transparency interface, exhibit a gap feature at about ±5 meV and no zero-bias conductance, consistent with the most literature data on oriented samples. The high-bias conductance has also been measured in order to obtain information on the properties of the barrier. A V-shape has been in some cases observed, instead of the parabolic behavior expected for tunnel junctions.

Zinc oxide is one of the most important semiconductor metal oxides and one of the most promising n-type materials, but its practical use is limited because of both its high thermal conductivity and its low electrical conductivity. Numerous studies have shown that doping with metals in ZnO structures leads to the modification of the band gap energy. In this work, Al-doped ZnO, Ni-doped ZnO, and undoped ZnO nanocrystalline powders were prepared by sol-gel method coupled with ultrasound irradiation. The doping concentration in ZnO was 1.0 at.% of Al and Ni. Influence of Al³⁺ and Ni²⁺ ions in the ZnO network are explored in this paper. X-ray Diffraction (XRD), Raman Spectroscopy, Nitrogen Adsorption (BET method), X-Ray Fluorescence (XRF) and Field Emission Scanning Electron Microscopy (FESEM) analyses demonstrated the incorporation of metal ions (aluminum and nickel) into the ZnO wurtzite structure. The crystallite size of the sample was decreased from 24.5 nm (ZnO) to 22.0 nm (ZnO-Al) and 21 nm (ZnO-Ni).

This research aimed to establish the relationship between carbon-nitrogen nutritional factors and copper sulfate on laccase activity (LA) by Pleurotus ostreatus. Culture media composition was tested to choose the nitrogen source. Yeast extract (YE) was selected as a better nitrogen source than ammonium sulfate. Then, the effect of glucose and YE concentrations on biomass production and LA as response variables was evaluated using central composite experimental designs with and without copper. The results showed that the best culture medium composition was glucose 45 gL-1 and YE 15 gL-1, simultaneously optimizing these two response variables. The fungal transcriptome was obtained in this medium with or without copper, and the differentially expressed genes were found. Main up-regulated transcripts included three laccase genes (lacc2, lacc6, and lacc10) regulated by copper, whereas the principal down-regulated transcripts included a copper transporter (ctr1) and a regulator of nitrogen metabolism (nmr1). These results suggest that Ctr1, which facilitates the entry of copper in the cell, is regulated by nutrient-sufficiency conditions. Once inside, copper induces transcription of laccase genes. This finding could explain why a 10 to 20-fold increase in LA occurs with copper compared to cultures without copper when using the optimal concentration of YE as nitrogen sources.

Computational investigations on the BPE-ligated Cu-catalysed enantioselective addition of enynes to ketones were performed with DFT method. Two BPE-CuMes catalysts, BPE-CuMes and (S,S)-Ph-BPE–CuMes, were employed to probe the reaction mechanism with the emphasis on stereoselectivity. The calculations on the BPE-CuMes system indicate that the actvie metallized enyne intermediate acts as the catalyst for the catalytic cycle. The catalytic cycle involves two steps: 1) the ketone addition to the alkene moiety of the metallized enyne; 2) the metallization of enyne followed by the release of product with the recovery of the active metallized enyne intermediate. The first step accounts for the distribution of the products, and therefore is the stereo-controlling step in chiral systems. In the chiral (S,S)-Ph-BPE–CuMes system, the steric hindrance is vital for the distribution of products and responsible for the stereoselectivity of this reaction. The steric hindrance between the phenyl ring of the two substrates and groups at the chiral centers in the ligand skeleton is identified as the original of the stereoselectivity for the titled reaction.

Copper, the highly toxicity micronutrient, plays two essential roles: it is a catalytic and structural cofactor for Cu-dependent enzymes, and it acts as a secondary messenger. In the cells, copper is imported by CTR1, a transmembrane high-affinity copper importer, and DMT1 (divalent metal transporter). In cytosol, enzyme-specific chaperones receive copper from CTR1 C-terminus and deliver it to their apoenzymes. DMT1 cannot be a donor of catalytic copper because it does not have cytosol domain which is required for copper transfer to the Cu-chaperons and following to cuproenzymes. Here we assume that DMT1 can mediate copper way required for regulatory copper pool. To verify this thought, we used CRISPR/Cas9 to generate H1299 cell line with CTR1 or DMT1 single knockout (KO) and CTR1/DMT1 double knockout (DKO). To confirm KOs of the genes qRT-PCR were used. Two independent clones for each gene were selected for further studies. In CTR1-KO cells, expression of the DMT1 gene was significantly increased. In subcellular compartments, copper concentration decreased dramatically in DKO cells. CTR1-KO cells, but not DMT1-KO, demonstrated reduced sensitivity to cisplatin and silver ions, agents that enter the cell through CTR1. The expression of genes, whose protein products require copper: HIF1α, XIAP, COMMD1, CCS, Cp, but not SOD1 and NF-kB, changed their level. Perhaps these data will help to understand how the disturbances of copper homeodynamics lead to the development of neurodegenerative and oncological disorders. Possibility of using CTR1 KO and DMT1 KO cells to study homeodynamics of catalytic and signaling copper selectively is discussed.

Over the years, scarcity of fresh potable water has increased the demand for clean water. Meanwhile, with the advent of nanotechnology, the use of nanomaterials for photocatalytic degradation of pollutants in wastewaters has increased. Herein, a new type of nanohybrids of La and Mn co-doped bismuth ferrite (BiFeO₃) nanoparticles embedded into transition metal carbide sheets (MXene) were prepared by a low-cost double solvent sol-gel method, and investigated for their photocatalytic activity. The photoluminescence results showed that pure BFO has highest electron hole recombination rate as compared to all the co-doped BFO/MXene nanohybrids. The larger surface area and higher electron-hole pair generation rate provides suitable environment for fast photo-degradation of organic molecules. The band gap of the prepared nanohybrids was tuned to 1.96 eV having largest BiFeO₃ surface area (147 m²g⁻¹) reported till date. Moreover, the BLFO/MXene and BLFMO-5/Mxene degraded the 92% organic pollutant from water in dark and remaining in light spectrum as compare to undoped BFO/Mxene due to enhancement of the surface area and electron-hole recombination rate upon doping. Therefore, these synthesized nanohybrids could be a promising candidate for photocatalytic applications in future.

Influence of water concentration on the properties of fluorine-doped tin oxide (FTO) thin films was systematically studied in this work. Home made SISOM’s SPEED techniques and its chemical formulation was employed to grow the FTO on quartz substrate. Water concentration in the precursor solution was varied from 0, 0.5, 1.0 and 1.5 mol %. The structural, optical, and electrical properties of the films were studied under these deposition conditions. The results show that the properties of the films varied significantly with water concentration. Scanning electron microscopy (SEM) revealed FTO films whose grain size and uniformity increases significantly with increase in water concentration. The structure of the films was measured by X-ray diffraction (XRD) measurement. It shows polycrystalline films with (110), (101), (200), (211) and (220) orientation; the strength increases as water concentration increases. The optical transmission was determined by UV-Vis spectroscopy at 380–780 nm UV-VIS regions. The optical transmittance varies with water concentration with an average of 84%. The electrical property, measured by Hall Effect revealed n-type semiconductor. The films have the following properties: resistivity, 15 × 10^-4Ω cm; carrier concentration, 18.7 × 10¹⁹ cm^-3 and mobility of 21.86 cm² V^-1 s^-1. The average figure of merit, φ of the FTO film is 1.25. Optimum deposition condition was established after series of experiments and was found to be 1.5% water concentration at 460^oC substrate temperature. The FTO films deposited in this work could be a promising replacement to indium tin oxide (ITO) especially in dye-sensitized solar cells.

This paper, the second in a series of two, describes the experimental results for removing arsenic from the dust collected in the electrostatic precipitators of a fluidized bed roasting oven (RP dust). The RP dust produced is discharged as a toxic waste, although its copper content is close to 20% by weight. This work aims to process the RP dust; until obtained a material with a low concentration of arsenic, which could be recirculated in smelting operations and recover the valuable metals. Based on the successful experience obtained in the first document with FS dust, this work proposes to use the reduction-sulphidation-volatilization processes to carry out the volatilization of arsenic from RP dust. A set of experiments was realized in the roasting different ratios of the mixture of copper concentrate / RP dust, sulfur / RP dust varying temperature and roasting time; to reach an arsenic concentration <0.5% by weight. The RP dust was characterized using different techniques, that confirmed more than 20% by weight of copper and describing its structure as a small particle agglomerate (<5 µm), with a complex sulfoxide morphology. The main results indicated: that for a 75/25 mixture of the copper concentrate / PR dust under 700 ° C, 15 minutes roasting time with air atmosphere, the arsenic volatilization was 96% by weight. Meanwhile, for a 5/95 mixture of sulfur / RP dust, at 650 ° C, the volatilization of arsenic was 67% by weight.

This paper (the first of a series of two) seeks to describe the experimental results of removing arsenic from dust collected in electrostatic precipitators of copper into the pyro-metallurgy gas cleaning systems. The first work corresponds to the treatment of dust contained in gas off generated in the copper Flash Smelting Furnace process (FS dust), while the second focuses on the treatment of dust generated from a Fluidized Bed Roasting Furnace (RP dust). The dust is complex sulphur-oxide-metals with concentrations of copper above 10 wt % and relatively high concentrations of silver. Due to the dust has an arsenic’s concentration above 5 wt %, makes it difficult to recover valuable metals through hydro-metallurgical processes or by direct recirculation of the dust into a smelting furnace. Thus, the development of pyrometallurgical processes aimed to reduce the concentration of arsenic in dust is the main purpose of this study, particularly the production of a material suitable for recirculation in smelting operations. The works conducted provide a detailed characterization of the dust, including Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN), Scanning electron microscope-Energy Dispersive X-ray analysis (SEM/EDS), X-ray diffraction (XR-D), elemental chemical analysis using Atomic Adsorption (A. A.) and X-Ray Fluorescence (X-RF). By considering that arsenic volatilization requires a process of reduction-sulphidation-volatilization, the works explore the roasting of mixtures of copper concentrate/dust, sulphur/dust and pyrrhotite/dust. The degree of volatilization was determined by elemental chemical analysis of arsenic in the mixture after and before the roasting process. The results indicated the effect of parameters such as temperature, gas flow, gas composition and the ratio of mixtures (concentrate, sulphur or pyrrhotite)/dust on the volatilization of arsenic. The findings indicate that the concentration of arsenic in the FS dust can be reduced to a relatively low level (<0.5 wt %), allowing to the material to be recirculated into smelting processes.

Impure and pure casts have collected reasonable attentions over all the world. In this paper, Aluminum (Al) and Copper (Cu) cast alloys are considered to be studied. Multiple impure and pure Al-Cu cast alloys are established under the condition of very high temperatures. Then, all of the established alloys are examined by applying mechanical tests. More specifically, tests of hardness are exploited. Moreover, different quenching conditions are employed and analyzed. These are the water, air and oil. Consistent results are separately obtained for the impure and pure materials.

In this work, oxygen-doped g-C3N4 mesoporous nanosheets (O-CNS) were synthesized via a facile recrystallization method with the assistance of H2O2. The crystal phase, chemical composition, morphological structure, optical property, electronic structure and electrochemical property of the prepared O-CNS samples were well investigated. The morphological observation combining with nitrogen adsorption-desorption results demonstrated that the prepared O-CNS samples possessed nanosheets-like morphology with porous structure. The O doping into g-C3N4 resulted in the augment of specific surface area, which could provide more active sites for photocatalytic reaction. Simultaneously, the visible-light absorption capacity of O-CNS samples was boosted owing to the regulation of O doping. The built energy level induced by the O doping could accelerate the migration rate of photoinduced carriers, and the porous structure was most likely to speed up the release of hydrogen during photocatalyic hydrogen process. Resultantly, the photocatalytic hydrogen production rate of the optimized oxygen-doped g-C3N4 nanosheets reached up to 2012.9 μmol•h-1•g-1, which was 13.4 times higher than that of bulk g-C3N4. Thus, the significantly improved photocatalytic behavior was imputed to the porous structure, the augment of active sites, and the enhancement of visible light absorption and charge separation efficiency.

A series of ZnO doped nitrogen-carbon materials (xZnO-N-C) with ZnO content of 5-40% are prepared by vacuum curing-carbonization strategy using polyamide-imide as N-C source and zinc nitrate as metal source for propane dehydrogenation (PDH). 20ZnO-N-C exhibits outstanding initial activity (propane conversion of 35.2% and propene yield of 24.6%) and relatively low deactivation rate (0.071 h-1) at 600 ◦C. The detailed characterization results show that small ZnO nanoparticles (5.5 nm) with high dispersion on the catalyst could be obtained by adjusting ZnO loading. Moreover, much more nitrogen-based species especially ZnNx species are formed on 20ZnO-N-C by comparison with 20ZnO-N-C-air prepared by curing-carbonization without vacuum, which may contribute for the higher product selectivity and catalytic stability of 20ZnO-N-C. The probable active sites for PDH reaction on the catalyst system are proposed to be C=O species and Zn2+ species. Moreover, the aggregation of ZnO nanoparticles is the primary reason for the activity loss on this catalyst system. The present finding not only provides the feasible construction strategy for the metal oxide doped nitrogen-carbon materials but also valuable guidance for the design of efficient catalyst in dehydrogenation of light alkane.

Acetaldehyde decomposition was performed under heating at the temperature range of 25-125oC and UV irradiation on TiO2 doped by the metallic Ni powder and TiO2 supported on the nickel foam. Process was carried out in high temperature reaction chamber “The Praying MantisTM”, with simultaneous in situ FTIR measurements and UV irradiation. Ni powder was added to TiO2 in the quantity of 0.5 to 5.0 wt%. Photothermal measurements of acetaldehyde decomposition indicated, that the highest yield of acetaldehyde conversion on TiO2 und UV irradiation was obtained at 75oC. Doping of nickel to TiO2 did not increase its photocatalytic activity. Contrary to that, application of nickel foam as a support for TiO2 appeared to be highly advantageous, because increased decomposition of acetaldehyde from 31 to 52% at 25oC and then to 85% at 100oC by comparison with TiO2 itself. At the same time mineralisation of acetaldehyde to CO2 increased two times at the presence of nickel foam. However, oxidised nickel foam used as support for TiO2 was detrimental. Most likely, different mechanisms of electrons transfer between Ni-TiO2 and NiO-TiO2 occurred. Application of nickel foam greatly enhanced separation of free carriers in TiO2. As a consequence, high yields of the photocatalytic reactions were obtained.

Graphene-based nanomaterials have emerged as promising materials for a wide range of applications.. Therefore, in the last years carbon nanoparticles have attracted great attention due to their low toxicity, high biocompatibility and easy preparation. Recently, N-doped carbon nanoparticles have been shown to have improved antibacterial activity over the undoped nanomaterial, but it is difficult to find correlations between the structure of the nanoparticle and its antibacterial activity. With this purpose, here, we analyze the effect of both, the nanoparticle size and the surface chemical composition of four N-doped carbon nanoparticles on the growth of Escherichia coli bacteria. Our results were analyzed using a Ligand-Substrate model based on the Monod´s equation, which allows us to interpret the dependence of the nanoparticle-bacteria affinity with the nanomaterial structure.

Carboxylic acids such as acetic acid and propionic acid have been investigated as representative components for fast pyrolysis (FP) bio-oil upgrading. Selective catalytic conversion of carboxylic acids can enhance bio-refinery processing economics through catalyst preservation and process intensification. Various metal-doped molybdenum carbide bead catalysts have been synthesized and developed in this work. Our aim is to enable selective conversion of carboxylic acids. In the case of acetic acid conversion, calcium doped Mo₂C beads offer the highest yield of acetone ~96% at 450 °C among undoped and Ca or Ni doped catalysts. By comparing hot gas filter with and without Ca-Mo₂C catalyst tested with real FP vapors, the former showed a 36.7% reduction of acetic acid, a 37.5% reduction of small ketones in aqueous phase, and a ~50% reduction of methoxies (methoxy phenols and methoxy aromatics) in organic phase. The conversion resulted in the formation of more long chain chemicals in the organic phase, which are more amendable for downstream upgrading.

A series of Eu³⁺ doped CaSiO₃/SiO₂ nano-phosphor powder of controlled grain size, crystalline structure, and chemical composition were synthesized using the microemulsion technique. XRD profiles of samples sintered over 600 of suggested phase shift from amorphous powder grain to more ordered polycrystalline powder of triclinic type wollastonite, CaSiO₃, with preferred crystal phase orientation of (112) and tetragonal type cristobalites of SiO₂. The grain size, crystallinity, and chemical composition of the host matrix, activator and sensitizer strongly affected both the absorption and emission bands of these samples. The amplitude of both the orange and red emission bands significantly increased with sintering temperature. The emission band is red-shifted with decreasing grain sizes. These bands displayed good sensitivity to ionic concentration of the Si⁴⁺, Ca²⁺, and Eu³⁺. With increasing Ca²⁺ ion concentration both the intensity of the red photoluminescence (PL) band increased and a concentration quenching observed. Increase in Si⁴⁺ ion concentration led to quenching in PL intensity of both the orange and red bands whereas the amplitude of the blue-band slightly increased. With increasing Eu³⁺ ion concentration the red-band initially increased whereas it started decreasing at higher sample concentration. In the presence of Ca²⁺ ion as a sensitizer, the sample showed a remarkable PL property—including—about 100% photon conversion efficiency and a two-fold increase in excitation and emission photons.

Tantalum doped ZnO structures (ZnO:Ta) were synthesized and some of their characteristics were studied. ZnO material was deposited on silicon substrates by using a hot filament chemical vapor deposition (HFCVD) reactor. The raw materials were a pill made of a mixture of ZnO and Ta₂O₅ powders, and molecular hydrogen was used as a reactant gas. Percentage of tantalum was varied from 0 to 500 mg by varying the percentage of tantalum oxide in the mixture of the pill source, by holding a fixed amount of 500 mg of ZnO in all experiments. X-ray diffractograms confirmed the presence of zinc oxide in the wurtzite phase and metallic zinc with a hexagonal structure, and no other phase was detected. Displacements to lower angles of reflection peaks, compared with those from samples without contamination, were interpreted as the inclusion of the Ta atoms in the matrix of the ZnO. This fact was confirmed by EDS and XRD measurements. From SEM images from undoped samples exhibited mostly micro sized semi-spherical structures while doped samples displayed a trend to grown as nanocrystalline rods. The presence of tantalum during the synthesis affects the way of the growth. Green photoluminescence at naked eye was observed when Ta doped samples were illuminated by ultraviolet radiation and confirmed by PL spectra. PL intensity on Ta doped ZnO varied from those undoped samples up to 8 times.

The accumulation of microorganisms, plants, algae, or small animals on wet surfaces that have a mechanical function causes biofouling, which can result in structural or other functional deficiencies. The maritime shipping industry must constantly manage biofouling to optimize operational performance, which is a common and long-lasting problem. It can occur in any metal structure in contact or submerged in ocean water, which represents additional costs in terms of repairs and maintenance. This study is focused on the production of antifouling coatings, made with nanoparticles of copper selenide (CuSe) modified with gum arabic, within a water-base acrylic polymeric matrix. During the curing of the acrylic resin, the CuSe NPs remain embedded in the resin but this does not prevent the release of ions. The coatings presented to release copper and selenium ions for up to 80 days, selenium was the element that was released the most. The adhesion of film coatings to metallic substrates showed good adhesion, scale 5B (ASTM D3359 standard). Antimicrobial activity tests show that the coatings have an inhibitory effect on Escherichia coli and Candida albicans. The effect being more noticeable when the coating is detached from the substrate and placed on a growing medium, than compared to the coating on a substrate. Scanning electron microscopy (SEM) observations show that nanostructured CuSe coatings are made up of rod-shaped and spherical particles whose range ranges from 12 to 25 nm. The Energy Dispersive X-ray spectroscopy (EDS) studies showed that the ratio of selenium nanoparticles is greater than that of copper and that their distribution is homogeneous

The exponential growth in the consumption of electronics, in combination with the reduction in their useful life, leads to a significant increase in the volume of electronic material discarded. Printed Circuit Boards (PCBs) are modules composed of ceramic, polymer and metallic materials of high economic value and with a great potential for damage to biotic and anthropic environments when inadequately discarded. The aims of this work was to study the main environmental impacts and the efficiency of mechanical operations in the electronic waste recycling process in optimizing the concentration of metallic copper. For this, the samples obtained were characterized according to their morphology and chemical composition, and subjected to physical and mechanical treatments: dismantling, grinding, separation by granulometry, density and magnetic property. The environment impacts were estimated by the Life Cycle Assessment of the pre-treatment processes, associated with copper extraction operations in WPCBs. According to the results obtained, it is possible to infer that the NM +1mm Concentrated product presents in its metallic composition around 78% of copper, which contributes to the efficiency of the hydrometallurgical extraction processes. It is noteworthy that the Concentrated class represents about 14% of copper (wt) taking into account the amount of 3.789 kg of PCB waste input material. The potential for reinsertion of the dust in the material recovery process is highlighted, given that the chemical composition of this particulate has a significant presence of metals. In general, it was found that due to the higher concentration (wt %) of the sample being allocated in the range of - 0.15mm + 0.05mm, the elements Fe (18.30%), Si (10.73%), Ca (9.21%) and Cu (8.89%) stand out regarding the participation of the elemental composition of this fraction and also regarding the general composition of the sample. Furthermore, the generation of dust during the fragmentation process, can be associated with occupational respiratory diseases when not managed. About the Life Cycle Assessment, in seven of the nine categories evaluated, crushing and screening activities accounted for more than 90% of the recorded impact values. In general, it is estimated that in the pre-treatment phase be generated 15.4 kg CO2 eq.

The study of the inherent factors that influence the isolation of one type of metallosupramolecular architecture over another is one of the main objectives in the field of Metallosupramolecular Chemistry. In this work, we report two new neutral copper(II) helicates, [Cu2(L1)2]·4CH3CN and [Cu2(L2)2]·CH3CN, obtained by means of an electrochemical methodology and derived from two Schiff-based strands functionalized with ortho- and para-t-butyl groups on the aromatic surface. These small modifications let us to explore the relationship between the ligand design and the structure of the extended metallosupramolecular architecture. The magnetic properties of the Cu(II) helicates were explored by EPR spectroscopy and DC magnetic susceptibility measurements.

The development of oxidation processes with generating powerful radicals is the most interesting and thought-provoking dimension of peroxymonosulfate (PMS) activation. In this study, a magnetic spinel CuFe2O4 was successfully prepared by a facile, non-toxic, cost-efficient co-precipitation method with the synergetic effect of photocatalytic PMS oxidation against recalcitrant benzotriazole (BTA) pollutant. The high particle dispersion and large surface area (201.898 m2/g) provided a high photocatalytic activity with CuFe2O4. The obtained results from the central composite design (CCD) analysis confirmed the optimum degrading rate of BTA reached 81.4% at the optimum operational condition of CuFe2O4= 0.4 g/L, PMS= 2 mM, BTA= 20 mg/L after 70 min irradiation time. As such, the active species capture experiments revealed the presence of •OH, SO4•‒, O2•‒ and h+ species in CuFe2O4/UV/PMS system where SO4•‒ was dominated for BTA photodegradation. The combination of photocatalysis and PMS activation enhanced the consumption of metal ions in redox cycle reactions, thus preventing metal leaching and maintain the recyclability with reasonable mineralization efficiency which achieved more than 40% total organic carbon removal after four batch experiments. A retardant effect on BTA oxidation was observed with comparing the water’s common anion constituents as HCO3‒ > Cl‒ > NO3‒ > SO2‒. Results from intermediates identification showed that the transformation pathway of BTA developed as the deprotonation, hydrolysis and ring cleavage processes promoting the practical potential of photo-absorbing CuFe2O4 catalyzed PMS which can be a promising method due to convenient magnetic separation form the solution.

Metal bioaccumulation and metallothionein (MT) expression were investigated in gills and liver of the red-blooded Antarctic teleost Trematomus hansoni with the aim to evaluate the possibility for this species to face, with adequate physiological responses, an increase of copper or cadmium concentrations in the environment. Specimens of this Antarctic fish were collected from Terra Nova Bay (Ross Sea) and used for a metal exposure experiment in controlled laboratory condi-tions. The two treatments lead to a significant accumulation of both metals and an increase of gene transcription only for the MT-1. The biosynthesis of MTs was verified especially in speci-mens exposed to Cd, but the majority of these proteins were soon oxidized, probably because they were involved in cell protection against the risk of oxidative stress, by reactive oxygen spe-cies scavenging. The obtained data highlighted the phenotypic plasticity of T. hansoni, a species evolved in an environment characterized by natural high concentrations of Cu and Cd, and maybe the possibility for the Antarctic fish to face the challenges of a world that is becoming every day more toxic.

This work discussed the advantages of reducing copper in molten copper slag with low S content. FactSage calculated the distribution of copper at equilibrium under different sulfur content. The effect of sulfur content on copper recovery under different oxygen partial pressures was pointed out. The effect of sulfur content on copper recovery in the actual reduction process was explored through experimental research. Under the condition of low sulfur, the Recovery of copper and the stability of the experiment have an ideal results.

In the human body, Copper (Cu) is a major and essential player in a large number of cellular mechanisms and signaling pathways. The involvement of Cu in oxidation-reduction reactions requires close regulation of copper metabolism in order to avoid toxic effects. In many types of cancer, variations in copper protein levels have been demonstrated. These variations result in increased concentrations of intra-tumoral Cu and alterations in the systemic distribution of copper. Such alterations in Cu homeostasis may promote tumor growth or invasiveness, or even confer resistance to treatments. Once characterized, the dysregulated Cu metabolism is pinpointing several promising biomarkers for clinical use, with prognostic or predictive capabilities. The altered Cu metabolism in cancer cells and the different responses of tumor cells to Cu are strongly supporting the development of treatments to disrupt, deplete or increase Cu levels in tumors. The metallic nature of Cu, as a chemical element, is key for the development of anticancer agents via the synthesis of nanoparticles or copper-based complexes with antineoplastic properties for therapy. Finally, some of these new therapeutic strategies such as chelators or ionophores have shown promising results in a preclinical setting, while others are already in the clinic.

Predicting copper price is essential for making decisions that can affect companies and governments dependent on the copper mining industry. Copper prices follow a time series that is non-linear, non-stationary, and which have periods that change as a result of potential growth, cyclical fluctuation and errors. Sometimes the trend and cyclical components together are referred to as a trend-cycle. In order to make predictions, it is necessary to consider the different characteristics of trend-cycle. In this paper, we study a copper price prediction method using Support Vector Regression. This work explores the potential of the Support Vector Regression with external recurrences to make predictions at 5, 10, 15, 20 and 30 days into the future in the copper closing price at the London Metal Exchanges. The best model for each forecast interval is performed using a grid search and balanced cross-validation. In experiments on real data-sets, our results obtained indicate that the parameters (C, ε, γ) of the model Support Vector Regression do not differ between the different prediction intervals. Additionally, the amount of preceding values used to make the estimates does not vary according to the predicted interval. Results show that the support vector regression model has a lower prediction error and is more robust. Our results show that the presented model is able to predict copper price volatilities near reality, being the RMSE equal or less than the 2.2% for prediction periods of 5 and 10 days.

Mining is one of the main economic activities of several developing countries as Chile. Due to the progressive fall of the ore grades and the increasingly refractory composition of minerals, concentrating plants have increased that has led to an increase in the generation of tailings. Tailings, especially those obtained in the past, have remaining copper and other valuable species in quantities that can potentially be recovered, such as gold, silver, vanadium and rare earth elements. This transforms this abundant waste into a potential source of precious or strategic metals for secondary mining. One of the techniques of solid-liquid separation that allows the processing of solutions with low concentrations of metals corresponds to the adsorption, and more recently the biosorption, which is based on the use of biological matrices that do not constitute an environmental liability after application. Biosorption occurs as a consequence of the wide variety of active functional groups present in the different types of biomass. Bacterial, fungal, plant and algal biomasses have been described as biosorbents, mainly for the treatment of diluted and simple solutions. This work aims to recover copper from leached tailings using biomass of the red algae Gracilaria chilensis as a biosorbent. The tailing samples were taken from an abandoned deposit in the north of Chile and after an acid leaching copper was biosorbed, for which the kinetics of adsorption and the equilibrium isotherms were studied, applying the Freundlich and Langmuir models. Operational parameters such as adsorbent dose, pH and initial metal concentration were studied.

This article presents the copper ions adsorption process using an activated carbon from winemaking wastes. The pH, temperature, activated carbon amount and initial copper concentration were varied based on a full factorial 2^k experimental design. Kinetic and thermodynamic studies were also carried out. The adsorption kinetics was found follow a pseudo-second-order model. The adsorption data fit better to the Langmuir isotherm. The ANOVA demonstrated that both pH of the solution and activated carbon dosage had the greatest influence on copper adsorption. The activation energy was -32 kJ·mol^-1 suggesting that the copper adsorption is a physic-sorption process. The best fit to a linear correlation was the moving boundary equation that controls the kinetics for the adsorption copper ions onto the activated carbon. The X-ray photoelectron spectroscopy (XPS) results reveal the existence of different copper species (Cu²⁺, Cu⁺ and or Cu⁰) on the surface of the carbonaceous adsorbent after the adsorption, which could suggest a simultaneous reduction process.

One of the largest in the archipelago silver-copper mineralisation at Mount Sigurdf′ellet in West Spitsbergen Island was found in 1990 by Russian geologists. Firstly genesis was caused exclusively with hydrothermal ore migration of a substance from the enclosing sandstone and siltstone of the Devonian age. But subsequent work on the ore and nearest rocks of the basement gave a new factual material on the geochemical characteristics of potential sources of metals and found new for this mineral occurrence - gold mineralization. Similarity of geochemical associations of Sigurd ore occurrence with nearby upper Proterozoic marble as the first likely source of ore substance and the second - caused by carbonate-containing streaks in Low Devonian sediments. Ore-formation, probably due to repeated hydrothermal processes and was completed in a period of tectono-magmatic activity in Jurassic-Cretaceous time.

In this study, the corrosion performances of ammonium copper quat (ACQ) and boric acid (BA) wood preservatives were investigated, with micronized copper quat (MCQ) and nano boron (NB) used as reference materials. In the study, Scots pine (Pinus sylvestris L.) wood samples were impregnated according to the full-cell process method with ACQ at 2.4% concentration, BA at 4% and MCQ and NB at 1%. The ACQ- and BA-impregnated samples were then impregnated for a second time using five different water-repellent materials: tall oil, linseed oil, sodium silicate, methyl hydrogen silicone and N'-N- (1, 8-Naphthalyl) hydroxylamine. Polyethylene glycol (PEG) 600 and aluminum sulfate were introduced as single impregnations in the form of homogeneous mixtures with the ACQ and BA. The corrosion properties of the impregnated and control samples, including metal weight loss (MWL) and corrosion depth, were examined. As a result, the MWL values of the ACQ-impregnated samples showed an increase compared to the control group. The MWL values of the MCQ-impregnated samples were lower than those of the samples impregnated with ACQ, whilst the MWL values of the BA-impregnated samples were higher than those of the samples impregnated with NB.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

This study focuses on the development and characterization of a series of six new dansyl derivatives (L1 to L6) and their integration into PMMA polymers for application in environmental sensing. The photophysical properties of these derivatives were extensively studied in various solvents and in solid state. A remarkable positive solvatochromic effect was observed, indicating their potential in microenvironmental polarity assessment. The dansyl derivatives demonstrated selective sensing capabilities for Cu2+ and Hg2+ metal ions, with the formation of mononuclear species. Additionally, their acid-base responsive nature was explored, revealing potential for pH-sensitive applications. The incorporation of these derivatives into PMMA polymers resulted in acid-base sensitive materials suitable for environmental monitoring, particularly in detecting hazardous gases and changes in pH levels. This integration overcomes the solubility limitations of dansyl compounds and extends their applicability in diverse sensing scenarios.

The solid-state technique was utilized to make a single phase of delafossite CuAlO2, along with 1%, 2%, 3% and 4% silver doped CuAlO2 samples in this study. The content of the samples was investigated using energy dispersive X-ray spectroscopy (EDS) equipped with a field emission scanning electron microscope (FE-SEM). The polycrystalline nature of all of the analyzed cases was confirmed by structural analyses utilizing an X-ray diffraction (XRD) pattern with a simple typical peak of CAO rhombohedral phase. Raman, FT-IR and UV–Vis spectroscopy were used to study the structural, and optical energy band gap (Eg) of Ag doped CuAlO2 nanoparticles. The Kubelka–Munk function was used to calculate the optical band gap of ACAO alloys using diffuse reflectance spectra, and it altered as the Ag ion concentration increased. A. c. impedance spectroscopy was used to investigate the dielectric characteristics of Ag doped CuAlO2 nanoparticles.

Mn-doped CeO2 and CeO2 with the same morphology (nanofiber and nanocube) were synthesized through hydrothermal method respectively. When applied to benzene oxidation, the catalytic properties of Mn-doped CeO2 were higher than those of CeO2, which was related with the concentration of O vacancy. Compared to CeO2 with the same morphology, more oxygen vacancies were formed on the surface of Mn-doped CeO2, due to Mn ion replacing Ce ion. The lattice replacement was analyzed through XRD, Raman, electron energy loss spectroscopy and electron paramagnetic resonance technology. The formation energies of oxygen vacancy on the different exposed crystal planes [(110) and (100)] for Mn-doped CeO2 were calculated by applying the density functional theory (DFT). The data showed that the oxygen vacancy was easier to be formed on the (110) plane. The factors influencing catalytic behavior were elaborated, which indicated that surface oxygen vacancy played an important part in catalytic reaction.

Cobalt ferrite nanoparticles (NPs) doped with rare earth (RE) metals with general formula CoFe_2-xRE_xO₄ (RE=Yb, Dy, Gd; x = 0.0 - 0.3) were synthesized by the co-precipitation method followed by post thermal treatment. The influence of RE doping on structural, magnetic and thermal properties and potential biomedical applications like magnetic hyperthermia has been investigated. In the as-prepared samples RE cations enter the spinel lattice as detected by X-ray diffraction. Thermal treatment leads to thermodynamically stable and relaxed single-phase spinel structures only for lower RE content, x = 0.01-0.05. However, annealed samples present higher mass magnetization values (M_S), up to 83 Am²/kg. RE content also affects M_S, especially in the case of annealed samples where it decreases linearly with x from about 80 Am²/kg (x = 0.01) to about 60 Am²/kg (x = 0.30). Thermal treatment induces a reduction in coercivity from 60-100 mT for as-prepared samples to 18-33 mT for annealed samples, in a nonlinear manner with respect to RE content. Heating efficiency, i.e., Specific Loss Power (SLP), of all samples has been studied using both magnetometric and calorimetric method to deeper examine the energy loss mechanisms involved.

To realize high response and selectivity gas sensor in detecting dissolved gases in transformer oil, in this study, the adsorption of four kinds of gases (H2, CO, C2H2 and CH4) on Pd-graphyne as well as the gas sensing properties evaluation were investigated. The energetically favorable structure of Pd doped γ-Graphyne was first studied, including the comparison of different adsorption sites and discussion of electronic properties. Then, the adsorption of these four molecules on Pd-graphyne was explored. The adsorption structure, adsorption energy, electron transfer and electron distribution, the band structure and density of states were calculated and analyzed. The results show that the Pd atom prefers to be adsorbed on the middle of three C≡C bonds and the band gap is smaller. The CO adsorption exhibits the largest adsorption energy and electron transfer and brings obvious change to the structure and electron properties to Pd-graphyne. Because of the conductance decrease after adsorption CO and acceptable recovery time at high temperature, the Pd-graphyne can be promising gas sensing materials to detect CO with high selectivity. This work offers theoretical support for the design of nanomaterials based gas sensor using novel structure for industrial application.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

Fabrication of a nanocrystal zinc oxide (ZnO)/nitrogen-doped (N-doped) graphene composite using a novel and facile in situ sol-gel technique is demonstrated. Two-dimensional nanostructure morphology with uniform ZnO nanoparticles (average diameter of 10.25 nm) anchored on N-doped graphene nanosheets was observed via electron microscopy. Because of the polar heteroatoms on the graphene sheets, an abundance sites for polysulfide absorption were provided. More importantly, the strong chemical interaction between ZnO and polysulfides efficiently hindered the transport of polysulfides. Consequently, the lithium/sulfur (Li/S) battery with the ZnO/N-doped graphene composite-coated separator delivered enhanced performance in terms of discharge capacity and cycling stability when compared to the cell with a normal separator. With the modified separator, the battery achieved a discharge capacity as high as 942 mAh g^-1 for the first cycle and remained at 90.02 mAh g^-1 after the 100th charge/discharge test at 0.1 C. Results indicate that impeding the shuttling of polysulfides contributes to efficiently improving the behavior of the Li/S battery.

The work reports a facile synthesis of high thermally-stable nanocrystalline anatase TiO2 nanoparticles (NPs) doped with different atomic concentrations (0.5, 1.0, 3.0, and 6.0%) of Gd3+ and Nd3+ ions by a template-free and one-step solvothermal process, using titanium(IV) butoxide as titanium precursor and dimethyl sulfoxide (DMSO) as solvent. The structure and morphology of the Gd3+, Nd3+, and 0.5%Gd3+-0.5%Nd3+/doped TiO2 NPs have been characterized by using various analytical techniques. The Gd3+/ and Nd3+/TiO2 molar ratios were found to have a pronounced impact on the crystalline structure, size, and morphology of TiO2 NPs. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) studies revealed the proper substitution of Ti4+ by Gd3+ and Nd3+ ions in the TiO2 host lattice. The as-prepared Gdx/TiO2, Ndx/TiO2, and Gd1.0/Ndx/TiO2 bimetallic NPs, x = 0.5, 1.0, 3.0, and 6%, have been investigated as electrocatalysts for hydrogen evolution reaction (HER) in 1.0 M KOH solution using a variety of electrochemical techniques. At any doping percentage, the Gd1.0/Ndx/TiO2 bimetallic NPs showed higher HER catalytic performance than their corresponding counterparts i.e. Gdx/TiO2 and Ndx/TiO2. Upon increasing the Nd content from 0.5 to 6.0%, the HER catalytic performance of the Gd1.0/Ndx/TiO2 bimetallic NPs was generally enhanced. Among the studied materials, the bimetallic Gd1.0/Nd6.0/TiO2 NPs emerged as the most promising catalyst with an onset potential of -22 mV vs. RHE, a Tafel slope of 109 mV dec-1, and an exchange current density of 0.72 mA cm-2. Such HER electrochemical kinetic parameters are close to those recorded by the commercial Pt/C (onset potential: -15 mV, Tafel slope: 106 mV dec-1, and exchange current density: 0.80 mA cm-2), and also comparable with those measured by the most active electrocatalysts reported in the literature. The synergistic interaction of Gd and Nd is thought to be the major cause of the bimetallic catalyst's activity.

There was a question on “how lanthanides doping in iron oxide affects cure kinetics of epoxy-based nanocomposites?” To answer, we synthesized samarium (Sm)-doped Fe3O4 nanoparticles via electrochemical method and characterized it using FTIR, XRD, FE-SEM, EDX, TEM, and XPS analyses. The magnetic particles were uniformly dispersed in epoxy resin to increase the curability of the epoxy/amine system. The effect of the lanthanide dopant on the curing reaction of epoxy with amine was explored by modeling DSC experimental data based on model-free methodology. It was found that Sm3+ in the structure of Fe3O4 crystal participates in cross-linking of epoxy by catalyzing the reaction between epoxide rings and amine groups of curing agents. In addition, the etherification reaction of active OH groups on the surface of nanoparticles reacts with epoxy rings which prolongs the reaction time at the late stage of reaction where diffusion is the dominant mechanism.

Iron Doped TiO₂ nanoparticles (Fe-TiO₂) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO₂ physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe³⁺) was in the lattice of TiO₂ and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe³⁺ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO₂ materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO₂) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO₂ (zero-iron TiO₂) and Aeroxide^® TiO₂ P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO₂ under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

Antibiotic residues in aquatic environment have the possibility to induce resistance in environmental bacteria, which ultimately might get transferred to pathogens making treatment of diseases difficultand poses a serious threat to public health. If antibiotic residues in the environment can be eliminated or reduced, it has the possibility to contribute antibiotic resistance. Towards this objective, water containing ciprofloxacin was treated with sunlight assisted photocatalysis using Fe doped ZnOnanoparticles for assessing the degradation potential of this system.Parameters like pH, temperature, catalytic dosage were assessed for the optimum performance of the system. To evaluate degradation of ciprofloxacin,both spectrophotometricas well as microbiological (loss of antibiotic activity)methods were employed. 100 mg/L Fe doped ZnO nanoparticle catalyst and sunlight intensity of 120,000–135,000 lux system gave optimum performance at pH 9 at 30 °C and 40 °C. At these conditions spectrophotometric analysis showed complete degradation of ciprofloxacin (10mg/L) by 210 min. Microbiological studies showed loss of antibacterial activity of the photocatalytically treated ciprofloxacin containingwater against Staphylococcus aureus (10⁸ CFU) in 60 min and for Escherichia coli (10⁸ CFU) in 75 min. Thedeveloped system, thus possess a potential for treatment of antibiotic contaminated waters for eliminating/reducing antibiotic residues from environment.

In this study, a graphene-doped porous silicon (G-doped/p-Si) substrate for low ppm H₂ gas detection by an inexpensive synthesis route was proposed as a potential noble graphene-based gas sensor material and to understand the sensing mechanism. The G-doped/p-Si gas sensor was synthesized by a simple capillary force-assisted solution dropping method on p-Si substrates, whose porosity was generated through an electrochemical etching process. G-doped/p-Si was fabricated with various graphene concentrations and exploited as a H₂ sensor operated at room temperature. The sensing mechanism of the sensor with/without graphene decoration on p-Si was proposed to elucidate the synergetic gas sensing effect generated from the interface between the graphene and p-type silicon.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

The first single crystal structure of the homoleptic copper (II) ML2 complex (M=Cu (II), L=curcumin) was obtained and its structure was elucidated by X-ray diffraction showing a square planar geometry. The supramolecular arrangement is supported by C-H···O interactions and the solvent (MeOH) plays an important role in stabilizing the crystal packing. The cytotoxic activity of the complex against six cancer cell lines substantially surpasses that of curcumin itself, and it is particularly selective against leukemia (K562) and human glioblastoma (U251) cell lines with similar antioxidant activity to BHT. This constitutes the first crystal structure of pristine curcumin complexed with a metal ion.

Organic Coatings have potential applications in the prevention of metal corrosion in an aqueous solution. The protective effect of SEBS coated copper corrosion in NaCl 3% solution was investigated by using electrochemical methods. The main objective of this work is to find the optimal conditions of the protocol immersion to evaluate the effects of SEBS ratio and two-immersion time on the anticorrosive behaviour of copper in 3 wt % NaCl solution in order to determine the best conditions to produce a protective SEBS film on the copper surface. Response Surface Methodology (RSM) is used as an optimization method. The study’s findings show the combination of three environmental factors that minimize corrosion rate. The Box-Behnken Design (BBD) is working perfectly for the statistical significance of the model (ANOVA test). This analysis calculates the contribution value of each parameter in changing the value of the corrosion rate (CR) in not only individual but also synergistic cases. The optimized parameters were found to be a 2.17% of SEBS ratio, 20 min of immersion 1, and 21 min of immersion 2. The electrochemical impedance spectroscopy tests confirmed the results.

Abstract Purpose Since their introduction, intrauterine devices (IUDs) have been associated with various complications. Avery rare complication is the perforation of the cervix by the strings of the IUD. Purpose of the current study is to present a novel case of cervical perforation by the strings of a copper IUD and to perform a systematic review of the literature. Materials and Methods The patient a 43-year-old attended the gynecology clinic in order to remove her copper IUD. Speculum examination revealed that both the strings of the IUD perforated the anterior lip of the cervix. Management options were offered, the patient opted for a hysteroscopic removal. We searched the electronic databases: MEDLINE, Cochrane Library,Google Scholar,EBSCO for similar cases. Results Electronic search yielded 1821 articles; 8 were selected for inclusion. Mean age of the women was 35,37±7,781, range (26-47) years. One woman (12.5%) was nulligravida;3 women were multigravida (37,5%). Seven women (87,5%) were asymptomatic. Three IUDs (37,5%) were LNG-IUS; 5 IUDs (62,5%) contained copper. Conclusions Cervical perforation by the strings of IUD is an extremely rare clinical entity. It is asymptomatic in general and in most cases the strings of the IUD may be returned back to the endocervical canal after surgical maneuvers.

Copper toxicity has been a selective pressure on the sea-ice bacteria due to its widespread occur-rence in Antarctica. Here, with a combined biochemical and metabolomic approach, the Cu2+ ad-aptation mechanisms of Antarctic bacteria were analyzed. Heavy metal resistance pattern of Pb2+ > Cu2+ > Cd2+ > Hg2+ > Zn2+ was observed. Copper treatment did increase the activity of antioxidants and enzymes, maintaining cellular redox state balance and normal cell division and growth. Metabolomics analysis demonstrated that fatty acids, amino acids, and carbohydrates played dominant roles in copper stress adaptation. The results indicated that the adaptation mechanisms of strain O5 to copper stress included protein synthesis and repair, accumulation of organic per-meable substances, up-regulation of energy metabolism, and formation of fatty acids. This study increases the resistance mechanism understanding of Antarctic strains to heavy metals in extreme environments.

Long-term changes in nanoparticles of copper-silver bimetallic systems on natural clinoptilolite obtained by ion exchange of Cu2+ and Ag+, and then reduced at different temperatures, have been studied. Even after storage under ambient conditions, XRD and UV-Vis diffuse reflectance spectra indicate the presence of nanospecies of reduced copper and silver. Scanning Electron Microscopy of aged bimetallic samples, reduced at the highest temperature (450oC) and the primary samples for their preparation, also aged, showed the presence of silver nanoparticles with a size of about 100 nm. They are formed in the initial ion-exchanged sample (without reduction) due to the degradation of Ag+ ions. The nanoparticles in the reduced sample are larger; in both samples they are evenly distributed over the surface. The presence of silver affects the stability and the mechanism of decomposition/oxidation of reduced copper nanospecies, and this stability is higher in bimetallic systems. The decomposition pattern of recently reduced species includes the formation of smaller nanoparticles and few-atomic clusters. This can occur, preceding the complete oxidation of Cu to ions. Quasi-colloidal silver, which is present in fresh bimetallic samples reduced at lower temperatures, transforms after aging into Ag8 clusters, which indicates the stability of these nanospecies on natural clinoptilolite.

There is an increasing interest in applying environmentally-friendly materials in wood protection technology. This include the use of less toxic active ingredients, as well as better fixation. This study investigates the formulation based on the combination of copper and Saqez resin on the physical and biological resistance properties of poplar wood. Samples were treated by either copper-ethanolamine (Cu/MEA) and/or Saqez resin at various treatment levels. A vacuum pressure procedure was applied. The retention, weight percent gain, water absorption, volumetric swelling, and decay resistance of the samples were then determined. The highest retention and weight percent gain were obtained at the samples treated with the combination of copper-based system and Saqez resin. Additionally, the combination of the copper and Saqez improved the physical properties and decay-resistance against white-rot fungus Trametes versicolor.

Copper smelting slag is a solution of molten oxides created during the copper smelting and refining process, and about 1.5 million tons of copper slag is generated annually in Korea. Oxides in copper smelting slag include ferrous (FeO), ferric oxide (Fe­₂O₃), silica (SiO­₂ from flux), alumina (AI₂O₃), calcia (CaO) and magnesia (MgO). Main oxides in copper slag, which iron oxide and silica, exist in the form of fayalite (2FeO·SiO₂). Since the copper smelting slag contains high content of iron, and copper and zinc. Common applications of copper smelting slag are the value added products such as abrasive tools, roofing granules, road-base construction, railroad ballast, fine aggregate in concrete, etc., as well as the some studies have attempted to recover metal values from copper slag. This research was intended to recovery Fe-Cu alloy, raw material of zinc and produce reformed slag like a blast furnace slag for blast furnace slag cement from copper slag. As a results, it was confirmed that reduction smelting by carbon at temperatures above 1400°С is possible to recover pig iron containing copper from copper smelting slag, and CaO additives in the reduction smelting assist to reduce iron oxide in the fayalite and change the chemical and mineralogical composition of the slag. Copper oxide in the slag can be easily reduced and dissolved in the molten pig iron, and zinc oxide is also reduced to a volatile zinc, which is removed from the furnace as the fumes, by carbon during reduction process. When CaO addition is above 5wt.%, acid slag has been completely transformed to calcium silicate slag and observed like blast furnace slag.

Preeclampsia (PE) is characterized by a series of clinical features such as hypertension and proteinuria associated with endothelial dysfunction and the impairment of placenta vascular endothelial integrity. This study aimed to investigate the effect of serum copper (Cu) level on some angiogenesis-related factors including vascular endothelial growth factor-A (VEGF-A), soluble Fms-like tyrosine kinase-1 (sVEGF-R1), soluble endoglin (sEng) and cerruloplasmin (Cp) in Iraqi women with preeclampsia (PE) and control pregnant women. Therefore, 60 women with PE in addition to 30 healthy pregnant women were enrolled in the study. Serum concentration of sEng, VEGF-A, sVEGF-R1, and Cu in PE group significantly increased (p<0.05) in the PE group compared with that in the control group. Increased production of antiangiogenic factors, soluble VEGF-A and sEng contribute to the pathophysiology of PE, indicating the involvement of these parameters in the angiogenic balance in patients with PE. Tests for between-subject effects showed that the circulating angiogenesis factors and Cu were significantly associated with the presence of PE. Serum Cu level was significantly correlated with VEGF- A and VEGF-R1 levels but not with sEng. Multiple regression analysis revealed that only Cp and BP can significantly predict the complications in women with PE. In conclusion, serum Cu has a role in the angiogenesis in women with PE and may be a new drug target in the prevention or treatment of PE.

Alumina dispersion-strengthened copper, Glidcop, is used widely in high-heat-load ultra-high-vacuum components for synchrotron light sources (absorbers), accelerator components (beam intercepting devices) and in nuclear power plants. Glidcop has similar thermal and electrical properties to OFE (oxygen free electrical) copper, but has superior mechanical properties, thus making it a feasible structural material; its yield and ultimate strength are equivalent to those of mild-carbon steel. The purpose of this work has been to develop a brazing technique to join Glidcop to Mo, using a commercial Cu-based alloy. The effects of the excessive diffusion of the braze along the grain boundaries on the interfacial chemistry and joint microstructure, as well as on the mechanical performance of the brazed joints, has been investigated. In order to prevent the diffusion of the braze into the Glidcop alloy, a copper barrier layer has been deposited on Glidcop by means of RF-sputtering.

The article discusses the validation process of a certain method of balancing gas contained in the pore space of rocks. The validation was based upon juxtaposition of the examination of rocks' porosity and the effects of comminution in terms of assessing the possibility of opening the pore space. The tests were carried out for six dolomite samples taken from different areas of the 'Polkowice-Sieroszowice’ copper mine in Poland. Before the rock material was ground, it was examined using the porosimetric method and subsequently subjected to the SEM analysis. After grinding, the research material was subjected to the granulometric analysis. Prior to the grinding process, the rocks' porosity fell in the range of 0.3-14.8%, while the volume of the open pores was included in the 0.01-0.06 cm3/g range. The research material was also characterized by inhomogeneous distribution of the pore volume. The grinding process was performed using an original device – the GPR analyzer. The ground samples were characterized by similar particle size distribution and mean diameters D_3.2 of about 4.0-4.5 µm. The SEM analysis revealed pores of various size and shape on the surface of the rock cores, while at the same time demonstrating lack of pores following the grinding process. The grain size distribution curves were compared with the cumulative pore volume curves of the cores before grinding. The resulting intersection points of both curves were seen as testifying to the presence of openings in the rock pores and release of the accumulated gas. The opening percentage of the pore space was associated with the coordinates of the curves' intersections. In order to confirm the argument put forward in this paper – i.e. that comminution of a rock to grains of a size comparable with the size of the rock's pores results in the release of gas contained in the pore space – the amount of gas released as a result of the comminution process was studied. The results of gas balancing demonstrated that the pore space of the investigated dolomites was filled with gas in amounts from 3.19 cm3/kg to 45.86 cm3/kg. The obtained results of the rock material comminution to grains comparable – in terms of size – to the size of the pores of investigated rocks, along with asserting the presence of gas in the pore space of the studied dolomites, were regarded as a proof that the method of balancing gas in rocks via rock comminution is correct.

CuO-ZnO-Al2O3 catalysts are designed for the low-temperature shift conversion in the process of hydrogen and ammonia synthesis gas production. The paper presents the results of research on recovery of copper and zinc from spent catalysts using pyrometallurgical and hydrometallurgical methods. Under reducing conditions, at high temperature, having appropriately selected the composition of the slag, more than 66% of copper in metallic form and about 70% of zinc in the form of ZnO can be extracted from this material. Hydrometallurgical processing of the catalysts was carried out using two leaching solutions: alkaline and acidic. Almost 62% of the zinc contained in the catalysts has been leached to the alkaline solution and about 98% of copper has been leached to the acidic solution. After the hydrometallurgical treatment of the catalysts, insoluble residue was also obtained in the form of pure ZnAl2O4. This compound can be reused to produce catalysts, or it can be processed under reducing conditions at high temperature to recover zinc. The recovery of zinc and copper from such a material is consistent with the policy of sustainable development and helps to reduce the environmental load of stored wastes.

The present study aimed to investigate the effect of cold deformation on the precipitation kinetics of a binary CuSc alloy containing 0.4 wt.% scandium using the experimental analysis method of differential scanning calorimetry (DSC). Non-deformed and 75% cross-section reduced cold-rolled, supersaturated specimens were tested at non-isothermal DSC runs at up to five different heating rates. The DSC results showed that cold deformation significantly accelerated the precipitation process in the binary alloy, leading to a decrease in the initial and peak temperatures of the exothermic reactions. The activation energies calculated with the Kissinger method, indicated that the precipitation activation energy decreased with increasing cold deformation. The findings of this study provide worthy implications to further optimize the processing of Cu-Sc alloys with improved mechanical properties.

Microwave absorbers with lightweight, good stability and high efficiency have attracted much attention for their applications in many contemporary fields. In this work, the 3D porous (Ni@NO-C)n/NO-C composite absorber was prepared by a wet chemistry method with Ni chains and melamine as precursors, in which NO-C (N,O-doped carbon) encapsulated Ni particles are homogenously dispersed in the 3D porous networks of NO-C in the form of (Ni@NO-C)n chains. The special microstructure of the as-prepared material is proved to be benefit for the improvement of its microwave adsorption performance. The as-synthesized (Ni@NO-C)n/NO-C composite ab-sorber exhibited an effective absorption bandwidth of 4.1 GHz and an extremely large reflection loss of -72.3 dB. The excellent microwave absorbing performances can be ascribed to the coopera-tive consequence of dielectric loss and magnetic loss along with the balance between attenuation capability and impedance match.

PEDOT:PSS (polyethylene dioxythiophene:polystyrenesulfonate) is a commonly used hole injec-tion layer (HIL) in optoelectronic devices due to its high conductive properties and work function. However, the acidic and hygroscopic nature of PEDOT:PSS can be problematic for device stability over time. To address this issue, in this study, we have demonstrated the potential of an organic-inorganic hybrid HIL, by incorporating solution-processed WOx nanoparticles (WOx NPs) into the PEDOT:PSS mixture. This hybrid solution was found to have a superior hole transport ability and low Ohmic contact resistance, contributing to higher brightness (~62 000 cd m-2) and current efficiency (13.1 cd A-1) in the manufactured quantum-dot based light-emitting diodes (QLEDs). In addition, the resulting devices achieved a relative operational lifetime of 7,071 hours, or approxi-mately twice that of traditional QLEDs with PEDOT:PSS HILs. The proposed method is an un-complicated, reliable and low-cost way to achieve long operational lifetimes without sacrificing efficiency in optoelectronic devices.

This study investigates the role of oxygen vacancy on Fe-doped CeO₂ catalyst activity for soot oxidation. The oxygen vacancy was assessed through Ce³⁺ content. The Fe content was varied between 0 and 30% for two catalyst preparation methods, co-precipitation (CP) and solution combustion synthesis (SCS). X-ray photoelectron spectroscopy indicates that ceria exists as both Ce₄₊ and Ce₃₊, while iron is present only as Fe₃₊. The catalyst’s activity was evaluated by ignition (T10) and combustion (T50) temperatures using thermogravimetric analysis. Optimum Fe contents yielding the highest activity were found to be 10% and 5% for CP and SCS catalysts, respectively. The surface area and morphology have shown moderate effect on catalyst activity, because catalytic soot oxidation involves solid-solid contact. More importantly, regardless of the fabrication method, it was found that Ce₃₊ content, which is closely related to oxygen vacancies, plays the most important role in affecting the catalyst activity.

Ga doped ZnO thin films were formed by the Ultrasonic Chemical Spray Pyrolysis method onto substrates using zinc acetate and gallium (III) nitrate hydrate as precursors. The structural, optical, surface and electrical properties were studied as a function of increasing Ga doping concentration from 0 to 6 at %. Structural studies were shown polycrystalline with a hexagonal crystal structure. The transparency in the visible range was around 85% for thin film deposited using 6 at % Ga doping. With the aim of determining surface images and surface roughness of the films atomic force microscope images were taken. Ga doping of ZnO thin films could markedly decrease surface roughness. Electrical resistivity was determined by four point method. The resistivity 2.0% Ga doped ZnO film was the lowest resistivity of 1.7 cm. In the photoluminescence measurements of the films, existence of UV and defect emission band was observed. As a result, Ga doped ZnO films have advanced properties and promising materials for solar cells.

Modeling and design of fiber lasers facilitate the process of their practical realization. Of particular interest during the last few years is the development of lanthanide ion-doped fiber lasers which operate at wavelengths exceeding 2000 nm. There are two main host glass materials considered for this purpose, namely fluoride and chalcogenide glasses. Therefore, this study concerns comparative modeling of fiber lasers operating within the infrared wavelength region beyond 2000 nm. In particular, the convergence properties of selected algorithms, implemented within various software environments, are studied with a specific focus on the central processing unit (CPU) time and calculation residual. Two representative fiber laser cavities are considered: one is based on a chalcogenide-selenide glass step-index fiber doped with trivalent dysprosium ions whilst the other is a fluoride step-index fiber doped with trivalent erbium ions. The practical calculation accuracy is also assessed by comparing directly the results obtained from the different models.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

The dopamine and uric acid are primary products of purine metabolism and they coexist in serum and the extracellular fluid of the central nervous system. Some diseases of the human body are due to abnormal levels of uric acid and dopamine. Thus, the clinical diagnosis of some diseases needs a sensitive and simultaneous analysis of uric acid and dopamine. In this study, a novel conductive composite film containing multi-walled carbon nanotubes (MWTs) with cooper phthalocyanine attached to acrylate polymer (MWCNTs-CuMAPC-PnBA) was fabricated and dropped on a glassy carbon electrode and used for the simultaneous determination of Uric Acid (UA) and dopamine (DA). The modified glassy carbon electrode showed satisfactory electrocatalytic activity toward dopamine and uric acid. Low detection limits were achieved at 0.174 µM of DA and 6.87 µM of UA and the linear detection ranges of DA and UA are 5-200 µM and 20-250 µM respectively. The proposed sensing system based on the modified GCE offers promising results for rapid, cost-effective and selective simultaneous detection of uric acid and dopamine. Also, the complex modified electrode showed satisfactory results to detecting simultaneously UA and DA in real human samples (human Urine) via the standard addition method.

Aryl chlorides and bromides in the presence of NHC palladium hydroxo dimers of the type [{Pd(µ-OH)Cl(NHC)}2] (where NHC = IPr, SIPr, IMes, SIMes) undergo an efficient and selective Sonogashira cross-coupling with terminal acetylenes. For the coupling of 4-chlorotoluene with phenylacetylene TON = 560000 was observed. The procedure enables high-throughput and selective synthesis of a broad spectrum of unsymmetrically substituted 1,2-diarylacetylenes. Nearly a quantitative amount of HCl was detected within cross-coupling products. Water plays the role of the base and is regenerated in the process so that it does not have to be used in stoichiometric amounts (relative to the limiting reactant). Generation of the active Pd(0) complex proceeds via ethanol oxidation.

The depletion of the ore reserves in the world necessitates the search for secondary sources such as waste products (tailings and slag). A smelter in Namibia has historic slag which accumulated over decades of its operating life. Analytical and mineralogical characterization of the slag was performed using the X-ray fluorescence (XRF) analysis, Atomic Absorption Spectrometer (AAS), ICP-OES, scanning electron microscopy energy dispersive spectroscopy (SEM-EDS) analysis, and optical microscopy analysis. The chemical analyses showed that the metal values contained in the slag were mainly copper, lead, and zinc whose average contents were approximately 0.3%Cu, 2.4%Pb and 3.2%Zn. About 10.5%Fe was also contained in the slag. Germanium was detected by scanning electron microscopy, but was however below detection limits of the chemical analysis equipment used. Based on the results, approximate conditions under which the different slag phases were formed were estimated and the recovery routes for the various metals were proposed. Analysis by both optical and scanning electron microscopy revealed that Zn and Fe occurred mainly in association with O as oxides, while Cu and Pb were mainly associated with S as sulphides. The slag consisted of three different phases; namely the silicate phase (slag), metallic phase and the sulphide phases. The slag phases were mainly glass, silicate phases and metallic and sulphide phases. It was observed that the metallic and sulphide phases were dominant in the finer size fractions (-75 µm) whereas the sulphide phase was also present in the coarser size fractions (+300 µm). An important finding from the microscopy examination was that the sulphide phases were interstitial and could be liberated from the slag. This finding meant that liberation and subsequent concentration of the sulphide phases was feasible using conventional processing techniques.

The one pot hydrogenolysis/hydrogenation reaction of maltose to 2 moles of sorbitol has been carried out over different supported Cu catalysts in water at 180°C and 40 bar of H2. Only the catalysts supported on silicas were found to be effective in this reaction giving up to 86% yield in the desired product while the bare supports and the catalysts supported on alumina or silica alumina gave messy reactions. The peculiar activity of the two Cu/Silica systems tested was ascribed to high metal dispersion and suitable polarity of the catalyst surface. The reduced catalyst, exposing metallic Cu particles on the surface, showed unusual stability in the presence of water as a solvent and could be reused several times without any treatment.

In this investigation, Cu-Ni alloys for possible fixed dental prostheses (FDPs), with different aluminum additions were produced using vacuum atmosphere. Annealed alloys (He atmosphere) with low aluminum concentration showed a coarse dendritic structure, while samples with high aluminum concentration showed a refined dendritic structure. Structural defects analyses have shown a relative low vacancy concentrations. Hardness value increases approximately five times for the alloyed samples compared with the as-cast and unalloyed samples. Compression test results have shown a noticeable strengthening improvement, mainly in samples heat treated with 10 at % Al, while samples with 5 at % Al presented also acceptable resistance. Results are discussed in terms of dislocation mobility and hardening precipitation mechanism.

Copper nitride (Cu3N), a metastable semiconductor material, but with reasonably-high-stability at room temperature, is drawing a great deal of attention as a very promising next-generation, earth-abundant, thin-film solar absorber. Its non-toxicity, on the other hand, makes it a very attractive eco-friendly semiconducting material. In the present work, Cu3N thin films were grown by employing radio-frequency magnetron sputtering, at room temperature, with 50-W RF-power, and partial nitrogen pressures of 8.0 and 1.0, onto glass substrates. Thus, the influence of argon on the optical properties of the Cu3N thin films was studied, with the goal of being able to achieve a low-cost, light absorber material, with appropriate properties in order to substitute the more conventional silicon, in photovoltaic cells. Variable-angle spectroscopic ellipsometry measurements have been conducted at three angles, 50∘, 60∘, and 70∘, respectively, in order to obtain the two ellipsometric parameters psi, ψ, and delta, Δ, respectively. For the constructed optical model, the bulk planar Cu3N layer is described by a one-dimensional graded-index model, combine with the mixture of a Tauc-Lorentz oscillator and up to four Gaussian oscillators, whereas a BEMA model with 50%-air-void is adopted in order to account for the existing surface-roughness layer. In addition, the optical properties such as the energy-band gap, and refractive index and absorption coefficient, were determined in order to assess the actual capability of this material as a light absorber for solar cells. The direct and indirect band gap energies were accurately calculated, and they were found to be in the ranges of 2.14-2.21 eV and very clse to 1.50 eV, respectively.

The metal chelator PBT2 (5,7-dichloro-2-[(dimethylamino)methyl]-8-hydroxyquinoline) acts as a terdentate ligand capable of forming binary and ternary Cu2+ complexes. It was clinically trialed as an Alzheimer’s disease (AD) therapeutic but failed to progress beyond phase II. The β-amyloid (Aβ) peptide associated with AD was recently concluded to form a unique Cu(Aβ) complex that is inaccessible to PBT2. Herein, it is shown that the species ascribed to this binary Cu(Aβ) complex in fact corresponds to ternary Cu(PBT2)NIm[Aβ] complexes formed by anchoring of Cu(PBT2) on imine nitrogen (NIm) donors of His side chains. The primary site of ternary complex formation is His6, having a conditional stepwise formation constant at pH 7.4 (K [M−1] ) of log K = 6.4 ± 0.1, and a second site is supplied by His13 or His14 (log K = 4.4 ± 0.1). The stability of Cu(PBT2)NIm[H13/14] is comparable with that of the simplest ternary complexes involving free imidazole (log K = 4.22 ± 0.09) and histamine (log K = 4.00 ± 0.05). The 100-fold larger formation constant for Cu(PBT2)NIm[H6] indicates that outer-sphere ligand–peptide interactions strongly stabilize its structure. Despite the relatively high stability of Cu(PBT2)NImH6, PBT2 is a promiscuous Cu2+-binding ligand capable of forming a ternary Cu(PBT2)NIm complex with any ligand containing NIm donor. These ligands include histamine, L-His, and ubiquitous His side chains of peptides and proteins in the extracellular milieu, whose combined effect should outweigh that of a single Cu(PBT2)NIm[H6] complex regardless of its stability. We therefore conclude that PBT2 is capable of accessing Cu(Aβ) complexes with high stability but not specificity. The results have implications for future AD therapeutic strategies and understanding the role of PBT2 in the bulk transport of transition metal ions. Given the repurposing of PBT2 as a drug for breaking antibiotic resistance, ternary Cu(PBT2)NIm and analogous Zn(PBT2)NIm complexes may be relevant to its antimicrobial properties.

This work aimed to carry out a bioremediation study to evaluate the resistance of Penicillium sp. isolated from kefir grains for the treatment of copper. The fungal culture medium was prepared using a 2% malt-agar medium at pH 7.0 in which Penicillium sp. was inoculated. Penicillium sp. growing in a liquid medium showed a decrease in biomass in presence of Cu(NO3)2 (800 mg.L-1), suggesting that the metal impacts the growth rate of the fungus. Moreover, the combined factors of pH and the presence of the inorganic contaminant impacted the radial growth of the fungus, causing inhibition of 73% at pH 4.0, 75% at pH 7.0, and 77% at pH 9.0 in liquid medium compared to control. However, images obtained with scanning electron microscopy showed the integrity of the fungus cell, even at high doses of copper in the medium. Therefore, it can be concluded that Penicillium sp. isolated from kefir grain can bioremediate the environment and that the harmful effects of heavy metals can be minimized as a result biosorption. Although the growth of Penicillium sp. is inhibited, such retardation requires high doses of copper nitrate, thus ensuring the use of this microorganism for protection against the harmful effects of non-essential copper in the environment.

Sphalerite has been recognized as the most important carrier of critical metal of Indium (In) due to that In mainly exists in the sphalerite lattice by isomorphic substitution. There are two significant replacing schemes for In entry into sphalerite, these are, Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+. In order to understand the reaction process and constraints of the two substitution schemes, this paper uses first-principles methods to calculate In and Ag, Cu replacing Zn in sphalerite. According to the substitution schemes of Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+, two doped sphalerite systems of Zn30InAgS32 and Zn30InCuS32 were constructed using 2×2×2 supercell model of sphalerite. Firstly, the pressure is controlled to 30MPa, and the temperature is set from 20-40MPa to simulate the response of the two doped sphalerite systems to temperature; Then, the control temperature was unchanged to 600K, and the pressure was set from 20-40MPa to investigate the pressure control of the two doped sphalerite systems. The lattice parameters, substitution energy, electronic structure, and population analysis of the designed models before and after replacement have been critically compared. The main conclusions can be drawn that it is more stable for In to enter sphalerite via the coupled substitution scheme Cu++In3+→2Zn2+, and the conditions that the two substitution schemes most likely to occur are 650K and 40MPa. This study not only reveals the physical and chemical properties of In-rich sphalerite formed by the two reaction processes of Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+, but also has a certain enlightenment effect on the search for indium in sphalerite, and promotes the application of first principles in mineralization analysis.

The current study aimed to evaluate the influence of different sintering temperatures on the properties of copper aluminum oxide (CuAlO₂) pellets synthesized from copper oxide (CuO) and aluminum hydroxide (Al(OH)₃) for application in smart infrastructure systems. The pellets were sintered at 400 K, 1000 K, and 1300 K, in the presence of nitrogen gas flow to reduce the amount of oxygen availability. The CuAlO₂ sintered nanoparticles were chemically analyzed by X-ray diffractometry, and the nanostructure of the materials was studied by scanning electron microscopy. The transmittance of the sintered materials was examined by ultraviolet/visible (UV/Vis) spectrophotometry, and 88% transparency was observed for the pellets sintered at 1300 K. Electrical conductivity was measured at 0.905 mS/cm, indicating a semiconducting behavior.

Mining and processing tailings often contain significant amounts of valuable metals, that can represent valuable sources of secondary raw materials. Especially this is case in early-stage operations, in which the head grades were higher, and the tailings were higher grade. These tailings can also present a substantial risk to the environment. Serbia has copper deposits which have been exploited since ancient times, and these operations have generated large amounts of mineral processing tailings. The main objective of this study is to show how valuables can be recovered from chemically and mineralogically challenging tailings. After detailed chemical and mineralogical characterization, the laboratory scale flotation tests focused on evaluating the effect of particle size, different types of collectors, pH, and pulp potential. Based on the test work, copper and gold can be recovered effectively into pyrite concentrate

Doped copper overpacks are planned to be utilized in the spent nuclear fuel repositories in Finland and in Sweden. The assessment of long-term integrity of the material is a matter of importance. Grain structure variations, segregation and any possible manufacturing defects in microstructure are relevant in terms of susceptibility to creep and damage from the loading evolution imposed by its operating environment. This work focuses on studying the microstructure level length-scale dependent deformation behavior of the material, of particular significance with respect to accumulation of plasticity over the extensive operational period of the overpacks. Reduced micromorphic crystal plasticity model, which is similar to strain gradient models, is used in this investigation. Firstly, the model’s size dependent plasticity effects are evaluated. Secondly, different microstructural aggregates presenting overpack sections are analyzed. Grain size dependent hardening responses, i.e., Hall-Petch like behavior, can be achieved with the enhanced hardening associated with the micromorphic model at polycrystalline level. It was found that the nominally large grain size in the base material of the overpack shows lower strain hardening potential than the fine grained region of the welded microstructure with stronger strain gradient related hardening effects. Size dependent regularization of strain localization networks is indicated as a desired characteristics of the model. The findings can be utilized to provide an improved basis for modeling the viscoplastic deformation behavior of the studied copper alloy and assess the microstructural origins of any integrity concerns explicitly by way of full field modeling.

Friction stir alloying (FSA) of commercially pure Cu with Ni, Zn, and Mg is implemented in the current study. The successfully fabricated alloy structure has been scrutinized in terms of mechanical and micro-structural standpoints. Energy-dispersive X-ray spectroscopy revealed a uniform distribution of alloying elements and coalescence at the atomic level. The compositional and grain size heterogeneity is managed in the stir zone, which pave way for microstructural control using FSA. Thus, the present study carries significance for the development of novel materials whose fabrication requires temperature far below the melting point of base metals. Ultra-refinement of grains is found to accompany the alloying process, with ~ 440 nm being the smallest grain size. Maximum and average micro-hardness enhancement of 18.4 % and 6 % is observed for the fabricated alloy. Tensile properties have also been investigated and co-related with the micro-structural morphology. The shift towards grain bimodality has also been reported, which is a highly sought property in the present day, especially to overcome the strength-ductility trade-off.

Mitigation of Anthropogenic CO2 emissions possess a major global challenge for modern societies. Herein catalytic solutions are meant to play a key role. Among the different catalysts for CO2 conversion Cu supported on molybdenum carbide is receiving increasing attention. Hence, in the present communication we show the activity, selectivity and stability of fresh-prepared -Mo2C catalysts and compare the results with those of Cu/Mo2C, Cs/Mo2C and Cu/Cs/Mo2C in CO2 hydrogenation reactions. The results showed that all the catalysts were active and the main reaction product was methanol. The results showed that copper-cesium and molybdenum effectively interact and that cesium promoted the formation of metallic Mo. While, the incorporation of copper is positive to improve the activity and selectivity to methanol, the presence of Mo0 phase was detrimental for the conversion and selectivity. Moreover, the catalysts promoted by cesium underwent redox surface transformations during the reaction that diminished their catalytic performance. The molybdenum phase in Cu/Mo2C changes during reaction leading to metallic molybdenum and tuning the catalytic activity.

Copper, which can potentially be a highly toxic agent, is an essential nutrient due to its role as a co-factor for cuproenzymes and participation in signaling pathways. In mammals, the liver is a central organ that controls copper turnover throughout the body: copper absorption, distribution, and excretion. In ontogenesis, there are two types of copper metabolism: embryonic and adult, which maintain the balance of copper in each of these periods, respectively. In the liver cells, these types are characterized by specific expression patterns and activity levels of the genes encoding ceruloplasmin, which is the main extracellular ferroxidase and copper transporter and proteins mediating ceruloplasmin metalation. In newborns, the molecular-genetic mechanisms responsible for copper homeostasis and the ontogenetic switch from embryonic to adult copper metabolism are highly adapted to milk ceruloplasmin as a dietary source of copper. In the mammary gland cells, the level of ceruloplasmin gene expression and the alternative splicing of its pre-mRNA govern the amount of ceruloplasmin in milk, and thus, the amount of copper absorbed by the newborn is controlled. In the newborns, absorption, distribution, and accumulation copper are adapted to milk ceruloplasmin. In the newborns, which are not breast-fed at the early stages of postnatal development, the control for alimentary copper balance is absent. We tried to focus on the neonatal consequences of a violation of the balance of copper in the mother / newborn system. Although there is still much to be learned, the time to pay attention to this problem came because the neonatal misbalance of copper may provoke the development of copper related disorders for future life.

A novel and simple method to improve the corrosion resistance of copper by constructing a 3D 1-dodecanethiol self-assembled monolayers (SAMs) in 3.5% NaCl solution is reported in this study. Several drops of 1% H3PO4 solution are thinly and uniformly distributed on copper surface to form a 3D nanostructure constituted by Cu3(PO4)2 nanoflowers. The anticorrosion properties of 1-dodecanethiol SAMs on copper surface and on copper surface treated with H3PO4 solution were evaluated. Results demonstrated that 1-dodecanethiol SAMs on bare copper surface exhibit good protection capacity, whereas a copper surface pretreated with H3PO4 solution can substantially enhance the corrosion resistance of 1-dodecanethiol SAMs.