With the development of free trade port in Hainan Island, the construction of tourist roads around the island is also in full swing. Under the weather conditions of strong typhoon and rainstorm in Hainan, the highway cutting slope built on the coastal weak sandy terraces has strong sand loss and is easy to be scour by rainfall. MICP green spray irrigation solidification technology is used to strengthen the sandy cutting, and pore water pressure monitoring is carried out on the slope model during MICP solidification and rainfall scour. Combined with the model pore water pressure and flow slip failure pattern, dynamic analysis was carried out. The results show that MICP sprinkler irrigation technology can solidified the surface of the slope model in a short time, and the cementation depth of the model reaches 4cm after three sets of rotation reinforcement. The surface reinforcement effect is good, and the sand samples are closely connected. Under the erosion effect of simulated rainfall intensity, the sand loss of the slope is weakened, and no sand binding damage occurs, and the integrity is enhanced. Due to the cementation between sand grains, most of the rainfall was converted into runoff, and the slope slid after 150s. When the slope began to slip, the leading edge of the slope model lost sand and unloaded, and the failure mode was graded creep slip failure. Finally, the slope was divided into several blocks due to the continuous expansion of cracks after the slope failure. The erosion stability of the sandy slope under heavy rains is optimized and the sand loss is prevented effectively. In this study, a new method of MICP remediation techniques is proposed, which provides a new test basis for the application of MICP technology in practical engineering.

Global warming has led to the increase in chalky grains of rice, which has also caused the deteriorations of physicochemical and cooking qualities of rice grains. These chalky rice grains are characterized by high α-amylase activity, high protease activity, and low apparent amylose contents, low degree of hardness and stickiness of boiled rice than those of the whole rice grains. In the present paper, we evaluated 14 Japonica unpolished rice grains harvested in Japan in 2021, and these samples (original grains) were divided to two groups (whole grain group and chalky grain one). We found that the chalky rice grains showed higher values of xylanase activity than those of the whole rice grains, while cellulase activity were lower than that of whole rice grains. Using rice grains blended with 30 % of chalky grains as material, we compared sugar and mineral contents and textural properties of the boiled rice grains soaked and boiled in the ordinary water or in the hard water, such as Evian or Contrex. It was shown that the hard water is useful for the prevention of the texture deterioration of the boiled rice grains due to the inhibition of the reduction of endogenous hydrolytic enzymes, such as amylase, proteinase, and xylanase. Furthermore, we found that hard water is useful for the increase of calcium and magnesium intake through the meal with the boiled rice grains soaked and cooked using hard water.

In recent years, since flood disasters have brought immeasurable losses to the city, it is urgent to prevent and solve the flood of stagnant water. Considering the shortage of real-time and accuracy of hydrological analysis, Opencv technology is used in this paper to process the obtained data in real time. For improved Yolov5, BoTNet and GAMAttention Transformer are used to improve Yolov5 to enhance its ability of recognition and prediction to better identify surface gathered water. The prediction rate of the improved Yolov5 is 7.1% higher than that of Yolov7 and 1.7% higher than that of Yolov5.After that, contour preprocessing of the image is carried out through the cropping technology of the identification frame to eliminate relatively unstable factors. The principle of binocular distance measurement is used to measure the three-dimensional coordinates of the actual distance, better constrain the contour proportion of the picture, and then the Opencv technology is used to get the outline of the water, and HSV is combined with better color processing pictures for the identification of the water and contour generation, and the area is obtained to correspond to the corresponding parameters of flood to provide important help in flood prevention and storm drainage.

The biodegradability of water hyacinth for biogas and biofertiliser production was studied under mesophilic conditions. The effects of water hyacinth pre-treatments were also included in this investigation. It was found that water hyacinth has a low biodegradability of 27% when monodigested while at a 3:1 ratio with cow manure, the biodegradability increases to 46%. At this elevated biodegradability, the water hyacinth biomethane potential was 185 LCH4/kgVS, while that of cow manure was 216 LCH4/kgVS. The Gompertz kinetic model had superior parameters than the Logistic model for most of the water hyacinth-cow manure combined substrate digestion. Based on the Gompertz model, the lag phase and daily maximum methane production rate were 5.5 days and 22.9 ml /day respectively for the 3:1 codigestion (R2 of 0.99). These values were 6.7 days and 15.2 ml/day respectively, in the case of water hyacinth monodigestion (R2 = 0.996). The dominant microbial species detected in the digestates were Bacteroidetes and Proteobacteria. A few microbial species were indigenous to water hyacinth but a more diverse consortia which is key to efficient substrate biodegradation, came from cow manure. The digestate contained ammonium nitrogen at 68 mg/kg with phosphorous and potassium at 73 and 424 mg/kg respectively. Nitrogen was lower but phosphorous and pottasium were comparable to previously studied digestates of other substrates. Only water hyacinth pretreated through aerobic composting proved to unlock a higher methane yield that matched a 3:1 codigestion with cow manure. Other pretreatments induced better biodegradation performance than that observed on untreated water hyacinth but this improvements were not as good as that of the 3:1 codigestion scheme. It was concluded that water hyacinth sourced from the Hartbeespoort dam, could be treated through anaerobic digestion to recover biogas and biofertilizer. However, more experiments are required to fully understand and harness the optimisation opportunities available in applying this technology to manage water hyacinth.

Photocatalytic technology based on specific band structure of semiconductors offers a promising way to solve the urgent energy and environmental issues in modern society. In particular, hydrogen production from water splitting over semiconductor photocatalysts attracts great attention owing to the clean source and application of energy, which highly depends on the performance of photocatalysts. Among the various photocatalysts, TiO2 has been intensively investigated and used extensively due to its outstanding photocatalytic activity, high chemical stability, non-toxicity and low cost. However, pure TiO2 has a wide band gap of approximately 3.2 eV, which limits its photocatalytic activity for water splitting to generate hydrogen only under ultraviolet light, excluding most of the inexhaustible sunlight for human beings. Fortunately, the band gap of semiconductors can be manipulated, in which introducing oxygen defects is one of the most effective measures to narrow the band gap of titanium oxides. This review starts out by the fundamentals of photocatalytic water splitting for hydrogen production over TiO2, discusses the latest progress in this field, and summarizes the various methods and strategies to induce oxygen defects in TiO2 crystals. Then, the next section outlines the modification approaches of oxygen-deficient titanium oxide (TiO2-δ) to further improve its photocatalytic performance. Finally, a brief summary and outlook of the researches on TiO2-δ photocatalysts for water splitting to produce hydrogen were presented.

The intrinsic non-linearity and complexity of suspended sediment dynamics, which are impacted by the geographical variability of basin parameters and temporal climatic patterns, make it difficult to estimate suspended sediment concentration (SSC) accurately in hydrological processes. Deep neural networks (DNNs), a cutting-edge modeling method that can capture the innate non-linearity in hydrological systems, have emerged as a solution to this problem. Using primary data on discharge, SSC, and turbidity, the long short-term memory method of DNNs was employed in this study to simulate the discharge-suspended sediment connection for the Esopus Creek, NY, USA as the first objective. To develop effective modeling strategies, multiple scenarios of feature selection, including combinations of discharge, turbidity and SSC for preceding days, were considered. Secondly, the variations in SSC and discharge between the three USGS gages along Esopus Creek that were upper stream, lower stream, and downstream, adjacent to the pourpoint were analyzed. Statistical metrics and scenarios of feature importance were used to evaluate the effectiveness of the DNN-based models. The study shows that among 24 DNN approaches feature selection is crucial in simulating the daily SSC, and discharge and presenting novel research directions for utilizing machine learning algorithms in water quality.

Hydrogeological maps must synthesize the scientific knowledge about the hydraulic features and the hydrogeological behavior of a specific area, and, at the same time, they must meet the expectations of land planners and administrators. Thus, especially in complex interconnected systems, hydrogeological maps can be fully effective when they are purpose-designed. In these contexts, usual graphical approaches in creating hydrogeological maps could result uncomplete and/or ineffective. Therefore, in case of complex systems and/or specific management/protection aims, new and purpose-designed graphical solutions must be applied to enhance the maps effectiveness. In the case study, these solutions show and emphasize all the hydraulic interconnections playing significant roles in recharging the multilayered alluvial aquifer, where the majority of wells have been drilled for drinking/industrial/agricultural purposes, artificial channels are used for agricultural purposes, and the shallow groundwater feeds protected groundwater-dependent-ecosystems. The hydrogeological map was then designed to be the synthesis of three different and hydraulically interconnected main contexts: (i) the main heterogeneous alluvial aquifer (the main target of the purpose-designed map), (ii) the hydrographic basin of a losing river that feeds the main alluvial aquifer, and (iii) those hard-rock aquifers (mainly turbiditic and ophiolitic) whose springs feed the same river.

Phytochemicals are gaining popularity due to their antioxidant effects and potential protection against inflammation, cardiovascular disease, and certain types of cancer. The retention of these phytochemicals during extraction must be maximized. This research focused on extracting bioactive compounds from Psidium guajava Linn leaves using solvent extraction (SE), microwave-assisted extraction (MAE), ultrasound-assisted extraction (UAE) with distilled water (DW) or 60% (v/v) ethanol/water (ET). Phytochemical screening demonstrated that all of the screening showed positive results in all extraction methods, except glycoside. There were no significant (p>0.05) differences in total phenolic (TPC) and flavonoid content (TFC) during MAE, SE, and UAE in case of ET. However, SE shows better (p<0.05) extraction of TPC and TFC than UAE and MAE in case of DW. ET shows better (p<0.05) extraction of TPC and TFC than DW. Antioxidant analysis shows the same trend though both DPPH and FRAP values were higher in MAE and SE for ET and DW, respectively. MAE/ET showed the highest inhibitory activity and dose-dependent response using SW480 cell via MTT assay. HPLC and TLC analysis reveal the fingerprint of morin, might function as an anticancer agent. In conclusion, MAE/ET is the most efficient among the extraction techniques in terms of anticancer activity.

The development of mineral deposits causes changes that are comparable to natural exogenous geological processes, and in local areas of intensive mining activity prevail over them. In this article, a diamond deposit is selected, developed by quarries of great depth, and a forecast is made of the impact of drainage water discharge on changes in the composition of surface water and bottom sediments during the entire period of development of the deposit. Modeling was per-formed according to various scenarios, taking into account changes in the total dissolved solids of groundwater from 0.5 to 21.7 g/kg H2O. Thermodynamic calculations were carried out using the HCh software package. The role of dissolved organic carbon in the migration of chemical elements and the effect of DOC on the precipitation of chemical elements from mixing solutions is given. It has been established that fulvic acid completely binds to Fe in the Fe(OH)2FA– complex in all types of natural waters and under all mixing scenarios. With humic acid, such a sharp competitive complex formation does not occur. It is distributed among the various elements more evenly. It was determined that the mass of precipitating iron in the presence of DOC decreases by 18-27%, and its precipitation in winter is more intense. In contrast to Fe, precipitation of Ca, Mg, and C from solution with DOC is higher in summer, and there are more of them in solution in winter. This study contributed to a better understanding of the behavior of heavy metals in surface waters and sediments under anthropogenic pressures in order to improve the sustainable management of water resources in the face of anthropogenic activities.

As the most commonly used hydrogel material in contact lenses, the amount of water in a lens affects its optical properties and comfort for the wearer. Therefore, an important challenge is to determine the safety and efficacy of contact lenses by accurately and non-destructively measuring the water content in real time. In this study, we demonstrate the accurate detection of water content in hydrogel contact lenses using a high-precision ATR format in a portable terahertz time-domain spectroscopy system. The technique can resolve small variations in the dielectric constant in solution, which is difficult to achieve with traditional transmission and reflection measurement modes. Information is obtained from the interaction between the sample and the swift waves propagating along the prism surface. The swift waves can excite longitudinal modes that are not directly accessible by conventional techniques. It is worth noting that the reference wave can be measured by removing the sample without disturbing the optical path. We also enhance the plasma effect at the interface with the hydrogel by using PVDF dielectric films of different polarities. We observed that the water content and refractive index changes in the ATR mode show different response patterns for nonpoled PVDF and poled PVDF membranes. This suggests that reflection and relative phase can be accurately evaluated in the THz-ATR technique, resulting in an accurate method for determining complex dielectric constants in the reflection geometry. This will allow accurate measurement of both surface and in vivo water content in hydrogels in the future and is a potential technical route for application in bioaqueous tissue measurements.

Abstract: This work is presenting a water level control and monitoring system in a tank, by using the development boards Arduino Uno, NodeMCU ESP8266 and the ultrasonic sensor HC-SR04. The water tank is supplied through a pump controlled by the development board Arduino Uno by means of a relay. The author has issued a control algorithm for controlling the water level and a program in the development environment Arduino IDE that has been implemented and validated on the experimental stand. For monitoring the development board NodeMCU ESP8266 has been used that takes the information from the ultrasonic sensor HC-SR04 and sends it through Wi-Fi to the platform ThingSpeak. Based on the experimental results it has been found out that the water level control system in the tank provides the performances imposed through the designing stage, and the pump running has been automatically stopped when the limit, settled through the program for the water maximum level in the tank, has been reached. The measured value of the water level is shown on the LCD 1602 display. In the water circuit of the home consumers or irrigation systems supplied from the tank a pump controlled by means of a mobile phone has been installed. In order to implement this control system, the author has issued a program for another development board Arduino Uno, whilst for the mobile phone he used the application Arduino Bluetooth Control. The advantage of this water level control and monitoring system in the tank is given by the very low costs in comparison to the cost of an industrial type control system.

A novel flexible humidity sensor, incorporating gold nanoparticles (Au NPs) and a trifunctional organosilica compound, has been developed through the integration of sol-gel processing, free radical polymerization, and self-assembly techniques. The trifunctional organosilica was initially synthesized by modifying (3-mercaptopropyl)trimethoxysilane (thiol-MPTMS) with 3-(trimethoxysilyl)propyl methacrylate (vinyl-TMSPMA). Subsequently, a hydrophilic polyelectrolyte, [3(methacryloylamino)propyl]trimethyl ammonium chloride (MAPTAC), was grafted onto the MPTMS-TMSPMA gel. The Au NPs were assembled onto the thiol groups present in the MPTMS-TMSPMA-MAPTAC gel network. The compositional and microstructural properties of the Au NPs/MPTMS-TMSPMA-MAPTAC composite film were investigated utilizing Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The presence of thiol groups and mesoporous silica skeletons ensured the stability of the humidity-sensing film on the substrate under highly humid conditions, while the hydrophilic groups functioned as humidity-sensitive sites. This innovative humidity sensor demonstrated high sensitivity, acceptable linearity, minimal hysteresis, and rapid response time across a broad range of working humidity levels. Based on the complex impedance spectra analysis, hydronium ions (H₃O⁺) were determined to govern the conductance process of the flexible humidity sensor.

Currently, the Israeli energy industry faces the challenge of a considerable increase in solar electricity production. Being a relatively isolated system, the significant expansion of solar electricity may cause problems with electricity quality. The electrical storage installation can resolve this problem. In Israel's situation, the optimal solution can be the creation of a channel between the Mediterranean and the Dead Sea. The channel can solve three closely related problems: the increased production of desalinated water for domestic, industrial, and agricultural needs; the prevention of a permanent Dead Sea level decline and its imminent disappearance; the development of hydro-pumping electrical storage stations; and the creation of numerous PV facilities in the Negev area for national electricity generation. However, a detailed analysis should be done for the estimation of the possible increase of solar electric generation with the consideration of a stochastic PV outcome and a potential ability to use the Dead Sea for the brine discharge from electrical hydro-storage plants.

Activated Corrosion Products (ACPs) formation and deposition pose a critical safety issue for nuclear fusion reactors. The working fluid transports the ACPs towards regions accessible to worker personnel. Predicting ACPs formation deposition and transport is fundamental for source term identification, reduction of radiation exposure assessment, maintenance plan definition, design optimization, and waste management. The code OSCAR-Fusion has been developed by the CEA (France) to evaluate the ACPs generation and transport in closed water-cooled loops for fusion application. This work aims at assessing the impact of water chemistry on the transport, precipitation, and deposition of corrosion products for the EU-DEMO divertor Plasma Facing Unit Primary Heat Transfer System. Sensitivity analyses and uncertainty quantification are needed due to the multi-physics phenomena involved in ACPs formation and transport. The OSCAR-Fusion/RAVEN code coupling developed by the Sapienza University of Rome and ENEA has been used. This work presents the perturbation results of different parameters chosen for a closed water-cooled loop considering a continuous scenario of 1888 days. The aim of this work is to assess the variation of build-up of ACPs, perturbing the alkalizing agent concentration into the coolant and the corrosion and release rates of different materials.

The photocatalytic hydrogen evolution reaction (HER) by water splitting has been studied, using catalysts based on TiO2 nanowires (TiO2NWs), which were synthesized by a hydrothermal procedure. This nanomaterial was subsequently modified by incorporating different loadings of gold nanoparticles (AuNPs) on the surface, previously exfoliated MoS2 nanosheets, and CeO2 nanoparticles (CeO2NPs). These nanomaterials, as well as the different synthesized catalysts, were characterized by electron microscopy (HR-SEM and HR-TEM), XPS, XRD, Raman, Reflectance and BET surface area. HER studies were performed in aqueous solution, under irradiation at different wavelengths, which were selected through the appropriate use of optical filters. The results obtained show that there is a synergistic effect between the different nanomaterials of the catalysts. The specific area of the catalyst, and especially the increased loading of MoS2 and CeO2NPs in the catalyst substantially improved the H2 production. Recyclability studies showed only a decrease in activity of approx. 7% after 15 cycles of use, which opens many possibilities regarding the potential use and scaling of these heterostructures in photocatalytic production of H2 from water.

In recent years, various optical measurement technologies such as far-infrared spectroscopy, low-frequency Raman spectroscopy, optical Kerr effect spectroscopy, and two-dimensional Raman-terahertz spectroscopy have developed vigorously. By comparing the complementary aspects detected by various linear and nonlinear spectroscopic techniques, a coherent picture emerges from studies of dynamics in water. Numerous molecular dynamics experiments and theoretical investigations have demonstrated low-frequency molecular motions in liquid water. For example, intermolecular hydrogen bond vibration, molecular reorientation motion, and the interaction between molecule/ionic solute and hydrogen bond all occur in the THz region, which are closely related to their physical/chemical properties and structural dynamics. However, precise probing of various modes of motion is difficult due to the complexity of the collective and cooperative motion of molecules and the spectral overlap of related modes. With the development of THz optical technology, current state-of-the-art THz sources can generate pulsed electric fields with peak intensities on the order of ~MV/cm. Such strong fields make it possible to use THz waves as the driving light source for nonlinear polarization of the medium, which in turn leads to the development of the emerging terahertz Kerr effect (TKE) spectroscopy technique. Many low-frequency molecular motion modes, such as the collective directional motion of molecules and the cooperative motion under the constraint of weak intermolecular interactions, are resonantly excited to unprecedentedly strong amplitudes driven by the THz electric field. Thereby the collected responses are increased. The TKE technique thus creates an interesting prospect for investigating low-frequency dynamics in these media. In view of this, this paper firstly summarizes the research work on the measurement mechanism of TKE spectroscopy by taking the solid material without low-frequency molecular dynamics process as an example. Starting from the principle of TKE technology and the exploration of the properties of solid matter using this technology, its application in the exploration of low-frequency molecular dynamics of liquid water and aqueous solutions is introduced. Liquid water is considered the building block of life and possesses many extraordinary physical and biochemical properties. Its hydrogen bonding network plays a crucial role in these properties. It is generally believed that the ability of water to form complex hydrogen-bonding networks is the main reason for its various kinetic and thermodynamic properties that are different from other liquids. However, the exact structure of the hydrogen-bonding network, the spatial extent of its existence, and the associated timescale are not known. And the relevant spectral information of the basic properties of the reaction water is still not known. Therefore, it is of great significance to evaluate the hydrogen bond-related kinetic properties of liquid water by optical means.

Adequate access to drinking water for hydration and hygiene depends on many factors, such as water quality, accessibility, continuity of supply, and available quantity. We developed the Drinking Water Security Index (DWSI) to assess relative multifactorial drinking water security at different spatial and temporal scales. We apply this new index in Sudan to assess historical and future drinking water security at state, local, and maternity levels. State-level analyses found that the Red Sea and River Nile states are most vulnerable, with the lowest DWSI for both historical and future periods. The 1 km2 pixel level analysis shows large differences in water security within the major states. Analyses at maternity level showed that nearly 18.97 million people are affected by the 10% of maternities with lowest DWSI, a number projected to increase by 60% by 2030. Current and future water security indexes of maternities providing Emergency Obstetric and Newborn Care, were assessed to identify those where urgent action is needed to ensure quality health care in water secure conditions. This work provides useful information for stakeholders in the health and drinking water sectors in Sudan, to improve public health, reduce preventable mortality, and make the population more resilient to projected environmental changes.

Mapping and prediction of inundated areas is increasingly important for climate change adaptation and emergency preparedness. Flood forecasting tools and flood risk models have to be compared to observed flooding patterns for training, calibration, validation and benchmarking. At regional to continental scale, satellite earth observation is the established method for surface water extent (SWE) mapping and several operational global-scale data products are available. However, the spatial resolution of satellite-derived SWE maps remains a limiting factor, especially in low-lying areas with complex hydrography, such as Denmark. We collected thermal imagery using an unmanned airborne system (UAS) for three areas in Denmark shortly after major flooding events. We combined the thermal imagery with an airborne lidar-derived high-resolution digital surface model of the country to retrieve high-resolution (40 cm) SWE maps. The resulting SWE maps were compared to low-resolution SWE maps derived from satellite earth observation (EO). We conclude that UAS have significant potential for SWE mapping at intermediate scales, can bridge the scale gap between ground observations and satellite EO and can be used to benchmark and validate SWE mapping products derived from satellite EO as well as models predicting inundation.

Bacteriological and physico-chemical analyses of fish pond water are very important in aquaculture as they give insights into likely threats to aquaculture and associated personnel. Bacteriological and physico-chemical profiles of selected fish ponds in the Ilorin West area of Kwara State, Nigeria, were investigated to evaluate the water quality of rearing enclosures. Physico-chemical analyses revealed quality parameters were within the recommended range for aquaculture. Following bacteriological analyses of static water pond culture, the TVC and TCC showed temporal variations, with concentration increasing with sampling time. However, the FCC showed fluctuation. Totally, 8 bacteria groups were isolated from both rearing enclosures. Of these, Gram-negative bacteria showed dominance. In which 5 Gram-negative (Escherichia coli, Proteus spp, Serratia spp, Enterobacter spp, and Pseudomonas spp) and 3 Gram-positive (Staphylococcus spp, Streptococcus spp, and Bacillus spp) were encountered. Estimates of bacteria occurrence in both rearing facilities respectively gave: Staphylococcus spp (20%), Streptococcus spp (12%), Proteus spp (8%) Enterobacter spp (20%), Serratia spp (16%), Bacillus spp (9%), Escherichia coli (8%), Pseudomonas spp (7%) from earthen pond water sampled. While Staphylococcus spp (18%), Streptococcus spp (16%), Proteus spp (8%), Enterobacter spp (22)%, Serratia spp (8%), Bacillus spp (15%), Escherichia coli (8%), Pseudomonas spp (6%) from concrete water sampled. Conclusively, although there is the presence of bacteria groups of public health concern, the static water exchange provides benefits of natural processing of wastes and restoration of the pond ecosystem. Notably, the presence of Escherichia coli indicates the presence of pathogenic organisms of enteric origin. The presence of these organisms has been associated with a lack of tentative pond management and effective biosecurity procedures.

The Greek seas as a part of the Eastern Mediterranean Sea, have been considered as a hotspot for the entrance of non-indigenous species (NIS). Ballast water functions as a major pathway for the spread of NIS in new environments, posing significant threats to both the ecosystems and human health. Nine non-indigenous fish species, originating from the Red Sea, have been introduced to the Greek seas since 1925. Despite the implemented laws for limiting the spread of NIS and the subsequent impacts, current global environmental issues, such as climate change and micro-plastic pollution, could result in a rapid spread and establishment of NIS in hot-spot regions, including the Greek seas. A more systematic use of advanced tools for the systematic monitoring of all NIS in the Mediterranean Sea is necessary.

Short-term changes in shallow bathymetry affect the coastal zone and therefore their monitoring is an essential task in coastal planning projects. This study provides a novel approach for monitoring shallow bathymetry change based on drone multispectral imagery. Particularly we apply a shallow water inversion algorithm on two composite multispectral datasets being acquired five months apart in a small Mediterranean sandy embayment (Chania, Greece). Initially, we perform radiometric corrections using proprietary software and following we combine the bands from standard and multispectral cameras resulting in a six-band composite image suitable for applying the shallow water inversion algorithm. Bathymetry inversion results showed good correlation and low errors (< 0.3m) with sonar measurements collected with an uncrewed surface vehicle (USV). Bathymetry maps and true-color orthomosaics assist in identifying morphobathymetric features representing crescentic bars with rip channel systems. The temporal bathymetry and true-color data reveal important erosional and depositional patterns, which were developed under the impact of winter storms. Furthermore, bathymetric profiles show that the crescentic bar appears to migrate across and along-shore over the 5-months period. Drone-based multispectral imagery proves to be an important and cost-effective tool for shallow seafloor mapping and monitoring when it is combined with shallow water analytical models.

This paper presents a robust method based on graph topology to find the topologically correct and consistent subset of inter-robot relative pose measurements for multi-robot map fusion. However, the absence of good prior gives a severe challenge to distinguish the inliers and outliers, and wrong loop closures can seriously corrupt the fused global map. Existing works mainly rely on the consistency of spatial dimension to select inter-robot measurements, which does not always hold. In this paper, we propose a fast inter-robot loop closure selection method that integrates the consistency and topology relationship of measurements, which both conform to the continuity characteristics of similar scenes and spatiotemporal consistency. The traditional high-dimensional consistency matrix is decomposed into the sub-matrix blocks corresponding to the overlapping trajectory area. Building on this logic, a clustering method involving topology correctness of inter-robot loop closures is introduced to split the entire measurement set into multiple clusters. We define the weight function to find the maximum cardinality subset with topologically correct and consistent, then convert the weight function to a maximum clique problem in the graph and solve it. We evaluate the performance of our method in a simulation and in a real-world experiment. Compared to state-of-the-art methods, the results show that our method can achieve competitive performance in accuracy while reducing computation time by 75%.

The problem of water drinking supply is very important in the world, especially for developing countries, in particular Algeria. In this work we propose to study a distillation system based on solar energy process using an artificial intelligence approach in order to enhance the performance and the daily production. For this purpose, a conventional solar still and capillary film solar still was used. The operating parameters of the two distilleries are analyzed and the neural network approach was used to predict the performance through the amount of distillate, solar radiation and ambient temperature. The sensitivity between the operating parameters of the solar still for two case have been studied through the artificial neuron network model. The obtained results are promising, analyzed and discussed.

What if oxygenic photosynthesis is a primordial process with roots at the origin of life? What would the impact of this change in perspective be on our understanding of the early Earth and of the emergence and diversification of life? In here, I will examine some of the historical context of the study of the evolution of photosynthesis, which led to the consolidation of the current notion that the origin of anoxygenic photosynthesis occurred before the origin of oxygenic photosynthesis. I will show with a few examples how the mainstream view on the evolution of photosynthesis traces back to Oparin’s ‘primordial soup’ scenario for the origin of life, fuelled by the century-old perception that oxygenic photosynthesis is a plant rather than a bacterial trait. However, it has become more evident than ever before that the mainstream view is not supported by the evolution of the photosystems. In other words, the origin of biological water oxidation appears to be the seed from where photosynthesis sprout. Somewhat troubling and contrary to all predictions that derive from the mainstream view, photosystem II—the water-splitting and oxygen-evolving enzyme—shows features that are better explained if photochemical reaction centres originated during the establishment of oxygenic photosynthesis. An urgent revision of the evolution of photosynthesis procured to be free from biases of interpretations and presuppositions is strongly encouraged from all angles of the Life and Earth Sciences.

Water is a limited resource that needs to be properly managed and distributed to the ever-growing population of the world. Rapid urbanization and development have drastically increased the overall water demand worldwide. Ageing water distribution networks are vulnerable to deterioration and leakage, thereby causing an estimated annual loss of about 48 trillion liters of water. To address these issues, efficient and reliable leakage detection and management techniques are necessary. In this paper, the results of the experiments performed on a looped water distribution network in AnSeong, Korea are discussed. Transient-based techniques were used and physical data were collected for the detection and localization of leakages in the experimental water pipes. The results obtained from the experiments demonstrated the applicability of transient techniques for leak analysis in looped water distribution networks.

Current hydrogen production is based on the reforming process leading to the emission of pollutants; therefore, a substitute production method is imminently required. Water electrolysis is an ideal alternative for large-scale hydrogen production, as it does not produce any carbon-based pollutant byproducts. Production of green hydrogen from water electrolysis using intermittent sources (e.g., solar, eolic) would facilitate clean energy storage. However, the electrocatalysts currently required for water electrolysis are noble metals, making this potential option expensive and inaccessible for industrial applications. Therefore, there is a need to develop electrocatalysts based on earth-abundant and low-cost metals. Nickel-based electrocatalysts are a fitting alternative because they are economically accessible. Extensive research has focused on developing nickel-based electrocatalysts for hydrogen and oxygen evolution. Theoretical and experimental work have addressed the elucidation of these electrochemical processes and the role of heteroatoms, structure, and morphology. Even though some works tend to be contradictory, they have lit up the path for efficient nickel-based electrocatalysts. For these reasons, herein, a review of recent progress is presented.

Bulukumba Regency, South Sulawesi, Indonesia is one of the centres for whiteleg shrimp, Litopenaeus vannamei production that applies intensive technology. However, no information has been obtained regarding the characteristics and status of water quality in coastal areas with environmentally friendly concepts and the potential to receive a waste load. The study aimed to determine the performance of whiteleg shrimp culture in relation to temporal and spatial aspects and characteristic and water quality status. Measurement and sampling of water were carried out before stocking/initial of culture whiteleg shrimp (rainy season) and end of culture/after harvesting of whiteleg shrimp (dry season) at two locations in the coastal area of ​​Bulukumba Regency, namely Bonto Bahari Subdistrict (BB) and Gantarang Subdistrict (GT). Variables measured and analyzed included temperature, salinity, pH, dissolved oxygen, nitrate, nitrite, ammonia, phosphate, total suspended solids, and total organic matter. Data analysis with descriptive statistics, multivariate statistics, and non-parametric statistics. The Storet (Storage and Retrieval) method was used to determine the water quality status. The results showed that the culture of whiteleg shrimp was technology-intensive with a stocking density of 110 - 220 ind/m² with productivity between 13.9 - 44.4 tons/ha/cycle. The predicted waste load of N is 28.00 tons/cycle and P reaches 6.61 tons/cycle. Another result was that changes in water quality status during the rainy season were classified as moderately polluted at the BB location and complying quality standards at the GT location, while in the dry season, both locations were categorized as heavily polluted. Variables of water quality that caused the decrease in water quality status in both locations (BB and GT) were observed to increase salinity, nitrate concentration, and ammonia concentration. However, there was a decrease in dissolved oxygen concentration in the dry season.

Water is essential for all living things however its pain has become serious. Many industrial activities cause its pollution by the release of polluting byproduct. Waste water treatment is hence necessary. In this context, the waste water of the textile industry containing Red Acid 52 was treated by the solid waste of the washed natural phosphate byproduct. Natural phosphate was also studied. The solid materials were first characterized by chemical analysis, Fourier Transform Infrared spectroscopy (FTIR) and X-ray diffraction (XRD). The phosphate materials were after that, tested in the adsorption of the Red Acid 52. The experimental data indicated that the phosphate waste rock allowed the removal of Red Acid 52. Its maximum retention capacity attained 18.4 mg.g-1. Calcinations of materials inhibits the removal capacity found reduced by 60 to 70%. The adsorption kinetics of the Red Acid 52 on the material is well described by the pseudo second order model while the adsorption isotherms are identified by the Langmuir model. Hereafter, the thermodynamic study revealed that the adsorption process is spontaneous and exothermic. Keywords: Waste water, Phosphate co-product, Adsorption, Red Acid 52.

The concern about consuming eco-friendly products has motivated research in the development of new materials. Therefore, films based on natural polymers have been used to replace traditional polymers. This study consists of a production of films based on gelatin reinforced with black pepper essential oil-loaded nanoemulsions and Cloisite Na⁺. The films were characterized by water vapor permeability, mechanical and thermal properties, surface contact angle, X-ray diffraction and scanning electron microscopy. It was observed that the films containing the nanoemulsion have higher permeability values and an increase in their mechanical resistance. The addition of nanoclay contributed to an increase in the surface hydrophobicity of the film and an increase in the tensile strength at break by about 150%. The addition of essential oil nanoemulsions led to an increase in thermal stability. The presence of clay dispersion contributed to the formation of a surface that was slightly rougher and grainier. The addition of the black pepper essential oil nanoemulsion resulted in an increase in porosity of the gelatin matrix. Through X-ray diffraction analysis, it was possible to conclude that both the polymeric gelatin matrix and the essential oils nanoemulsion are intercalated with the clay dispersion.

This work describes a method to carry out 2-D inversion of gravity data in terms of porosity and matrix density distribution using previous DC resistivity inversion results to constraint the fractional pore-water content in the rocks. The inversion is carried out using a controlled random search (CRS) algorithm for global optimization. The method was tested on synthetic data generated from a model representing a graben, and the results show that it can estimate accurate values of contrast-density and porosity. The method was also applied to gravity and dc experimental data collected in NE Portugal, showing results that agree quite well with the known geological information.

The Florida Keys, a delicate archipelago of sub-tropical islands extending from the south-eastern tip of Florida, host the vast majority of the only coral barrier reef in the continental United States. Abiotic as well as microbial components of the surrounding waters are pivotal for the health of reef habitats, and thus could play an important role in understanding the development and transmission of coral diseases in Florida. In this study, we analyzed microbial community structure and abiotic factors in waters around the Florida Reef Tract. Both, bacterial and eukaryotic community structure were significantly linked with variations in temperature, dissolved oxygen and total organic carbon values. High abundances of copiotrophic bacteria as well as several potentially harmful microbes, including coral pathogens, fish parasites and taxa that have been previously associated with Red Tide and shellfish poisoning were present in our datasets and may have a pivotal impact on reef health in this ecosystem.

Currently, a large part of the wells for agricultural use located in the state of Sonora are overexploited, which generates a high degree of saline intrusion and abandonment by nearby communities. In this paper the temperature effect on the final concentration of permeate water was evaluated through voltage and intel concentration variations in a batch electrodialysis reversal process (EDR), in order to identify optimal operating conditions with emphasis on the reduction of energy consumption and cost of desalinated water. Thirty-six samples were prepared: eighteen 2,000 mg/L total dissolved solids (TDS) samples and eighteen 5,000 mg/L TDS samples; brackish well water of 639 mg/L TDS and synthetic salt were mixed to obtain those concentrations. 3 different temperatures (25, 30, 35 °C) and 2 different voltages (10 and 20 V) were tested for each sample. The best salt removal occurred in the 20 V arrays, with 18.34% higher removal for 2,000 mg/L TDS experiments and 25.05% for 5,000 mg/L experiments (average between the 25 to 35 °C tests). Temperature positively affected EDR, especially in the experiments at 10 V voltage, where increasing 10 °C increased its efficiency by 10.83% and 24.69% for 2,000 and 5,000 mg/L TDS, respectively. Energy consumption was lower with increasing temperature (35 °C), as it decreased by 1.405% and 1.613% for 2,000 and 5,000 mg/L TDS concentrations, respectively (average between 10 and 20 V tests), decreasing the cost per m3 of water.

Two types of trenches cross-section in conventional vertical and brand new reverse-V-shape have fabricated on SCD substrate by micro-jet water-assist laser, the epitaxial lateral overgrowth technique has applied by microwave plasma chemical vapor deposition system in forming multiple micrometer-size channels. Raman and SEM techniques have applied in analyze both types growth layer characterization. Optical microscope has used to test microchannels hollowness. As a result, with the brand new reverse-V-shape trench, epitaxial lateral overgrowth layer reaches higher SCD surface morphology and crystal quality.

Recently, we have witnessed a booming development of composites and multi-dopant metal oxides to be employed as novel photocatalysts. Yet the practical application of photocatalysis for environmental purposes is still elusive. Concerns about the unknown fate and toxicity of nanoparticles, unsatisfactory performance in real conditions, mass transfer limitations and durability issues have so far discouraged investments in full-scale applications of photocatalysis. Herein, we provide a critical overview of the main challenges that are limiting large-scale application of photocatalysis in air and water/wastewater purification. We then discuss the main approaches reported in the literature to tackle these shortcomings, such as the design of photocatalytic reactors that retain the photocatalyst, the study of degradation of micropollutants in different water matrices, and the development of gas-phase reactors with optimized contact time and irradiation. Furthermore, we provide a critical analysis of research-practice gaps such as treatment of real water and air samples, degradation of pollutants with actual environmental concentrations, photocatalyst deactivation, and cost and environmental life-cycle assessment.

NMR Spectroscopy is used, in the temperature range 180-350K, to study local order and transport in liquid water (pure and confined) and its solutions with glicerol and methanol at different molar fractions. Being the liquid water thermodynamic dominated by polymorphism (two coexisting liquid phases: high- and low-density HDL and LDL) - with the LDL due to the hydrophilic HB interactions, originating in the supercooled regime the tetrahedral networking and the liquid-liquid transition – we focused our interest to hydrophobic effects (HE) on these. Nowadays, if compared to the hydrophilicity, little is known about hydrophobicity so that the main purpose of this study is to gain new information on it. We measured the relaxation times (T1 and T2) and the self-diffusion (DS). From the times we took advantage of the NMR property to follow the behaviors of each molecular component (the hydrophilic and hydrophobic groups) separately; they are studied directly and DS in terms of the Adam-Gibbs model: obtaining the configurational entropy (Sconf ) and the specific heat contributions (CP,conf ). Due to the HE all the studied quantities, behave differently. For water-glycerol the HB interaction is dominant for all the conditions, whereas for water-methanol are observable two different T-regions above and below 265 K, dominated respectively by the hydrophilicity and hydrophobicity. A situation linked to the water polymorphism. Below this temperature, where the LDL phase and the HB networking develops and grows, the times and CP,conf change behaviors leading to maxima and minima. Above it, where the HB becomes weak and less stable and the HDL dominates, the hydrophobicity determines the solution properties.

The diffusion process of water molecules within a polyetherimide (PEI) glassy matrix has been analyzed by combining the experimental analysis of water sorption kinetics performed by FTIR spectroscopy with theoretical information gathered from Molecular Dynamics simulations and with the expression of water chemical potential provided by a non-equilibrium lattice fluid model able to describe the thermodynamics of glassy polymers. This approach allowed to construct a convincing description of the diffusion mechanism of water in PEI providing molecular details of the process related to the effects of the cross- and self-hydrogen bondings established in the system on the dynamics of water mass transport.

Eco-friendly and low-cost water-based nanolubricants containing rutile TiO2 nanoparticles (NPs) were developed for accelerating their applications in industrial-scale hot steel rolling. The lubrication performance of developed nanolubricants was evaluated in a 2-high Hille 100 experimental rolling mill at a rolling temperature of 850 ℃ in comparison to that of pure water. The results indicate that the use of nanolubricant enables to decrease the rolling force, reduce the surface roughness and the oxide scale thickness, and enhance the surface hardness. In particular, the nanolubricant consisting of 4 wt% TiO2, 10 wt% glycerol, 0.2 wt% sodium dodecyl benzene sulfonate (SDBS) and 1 wt% Snailcool exhibits the best lubrication performance by lowering the rolling force, surface roughness and oxide scale thickness up to 8.1%, 53.7% and 50%, respectively. The surface hardness is increased by 4.4%. The corresponding lubrication mechanisms are attributed to its superior wettability and thermal conductivity associated with the synergistic effect of rolling, mending and laminae forming that are contributed by TiO2 NPs.

The assessment of water quality consists of counting bacteria indicating fecal contamination or detecting the presence of pathogenic bacteria using standardized or validated methods of classical microbiology. Our present study aims to determine the bacteriological quality of drilling water in the Tandjilé region of Chad. Our method used was based on qualitative and quantitative research on suspected total coliforms, Echerichia Coli and fecal enterococci were analyzed according to the standard routine methods of the French Association for Normalization (AFNOR). Microbiological analysis shows the presence of indicators of fecal contamination such as total coliforms, Escherichia coli and fecal enterococci. The number of strains detected in 100 ml were E. coli (7 /29 samples), fecal Streptococcus (6 /29 samples) and total coliforms (29/29 samples), respectively from borehole water. The contamination rate of E. coli is 24.13%, total coliforms 100% and 20.68% of fecal enterococci in boreholes. The high number of these microorganisms is more than the values recommended by the WHO for the quality of drinking water. Corrective and urgent measures are needed to improve the quality of these water resources, rich in pathogens, which are health risks, and the causes of infectious diseases such as gastroenteritis, diarrhea, typhoid and skin diseases.

Dissolved Oxygen (DO) concentration is a vital parameter that indicates water quality. DO short term forecasting using time series analysis on data collected from an aquaculture pond is presented here. This can provide data support for an early warning system for an improved management of the aquaculture farm. The conventional forecasting approaches are commonly characterized by low accuracy and poor generalization problems. In this article, we present a novel hybrid DO concentration forecasting method with ensemble empirical mode decomposition (EEMD) based LSTM (Long short-term memory) neural network (NN). With this method, first, the sensor data integrity is improved through linear interpolation and moving average filtering methods of data preprocessing. Next, the EEMD algorithm is applied to decompose the original sensor data into multiple intrinsic mode functions (IMFs). Finally, the feature selection is used to carefully select IMFs that are strongly correlated with the original sensor data and integrate both into inputs for the NN. The hybrid EEMD-based LSTM forecasting model is then constructed. Performance of this proposed model in training and validation sets was compared with the observed real sensor data. To obtain the exact evaluation accuracy of the forecasted results of the hybrid EEMD-based LSTM forecasting model, three statistical performance indices were adopted: MAE, MSE, and RMSE. Results presented for short term (12-hour period) and long term (1-month period) give a strong indication of suitability of this method for forecasting DO values.

The quantified residence time distribution (RTD) provides a numerical characterization of mixing in the continue casting tundish, thus allowing the engineer to better understand the metallurgical performance of the reactor. This paper describes a computational fluid dynamic (CFD) modelling study for analyzing the flow pattern and the residence time distribution in a five-strand tundish. Two passive scalar transport equations are applied to separately calculate the E-curve and F-curve in the tundish. The numerical modelling results are compared to the water modelling results for the validation of the mathematical model. The volume fraction of different flow regions (plug, mixed and dead) and the intermixing time during the ladle changeover are calculated to study the effects of the flow control device (FCD) on the tundish performance. The result shows that a combination of the U-baffle with deflector holes and the turbulence inhibitor has three major effects on the flow characteristics in the tundish: i) reduce the extent of the dead volume; ii) evenly distribute the liquid streams to each strand and iii) shorten the intermixing time during the ladle changeover operation.

Governments all over the world are currently grappling with the COVID-19 pandemic. While some countries were very hard hit, others were only mildly hit but all are still taking measures to mitigate the consequences. The virus emerged in December 2019 in Wuhan, China and spread to most continents by the beginning of March 2020, which led to the World Health Organization declaring it as a pandemic on the 11^th of March 2020. Since it was a novel disease, there was limited information on the virus, Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2) belongs to the same family as the Severe Acute Respiratory Syndrome Coronavirus 1 (SARS-CoV-1) and the Middle East Respiratory Syndrome Coronavirus (MERS-CoV). Researchers all over the world started working simultaneously to understand the virus to provide the necessary treatment regime or vaccine in order to reduce the impact of the virus on its victims. Africa and other developing countries with limited resources and poor planning and management are expected to be among the worst hit in the long run. The implications of the COVID-19 on food, water, hygiene, sanitation, and the environment in Africa have been reviewed in this paper, as well as possible implications they may pose to the population, based on the existing common practices and their immediate impacts. This information can assist policymakers in Africa to adequately plan the management of the COVID-19 in order to lessen its impact on the population.

AMR and drug void have caused huge panic today with few thousand death per year. MDR Typhoid was a serious old disease and caused serious health hazard in humen and animals demanding an update on molecular biology of the status on transferable genetic elements. R-plasmids combined in F’-plasmid and the new MDR conjugative plasmids were shown abundant in Sanmonella ranging 70-440kb with similarities. BlaTEM, blaCTX-M, blaOXA, blaNDM mdr genes were abundant in >50 plasmids analyzed and metal resistant gene clusters are predominant in most large plasmids. Among the acetyltransferase all catA1, aacA1 and aac-1b-cr genes were located. Abundant streptomycin phosphotransferases (StrAB) and rarely colistin resistant Mcr-5/9 phosphoethanolamine–lipid A transferase were detected. Altered isomeric dihydropterote synthases (Sul1/2/3) were present giving sulfamethoxazole resistance and dhfr gene frequently associated giving trimethoprim resistance. Metal resistant gene clusters like SilABC (CusABC), PcoAB, RcnA, terABC, and merABCXT etc were found in many Salmonella enterica plasmids. Toxin genes like HipA and virulence genes like spvABD were located in few plasmids increasing virulence and pathogenesis. Drug efflux genes tetA or tetB and OqxB, floR, CmlA were frequent where as QepA and EamA genes were rarely seen. Thus, Salmonella metal resistant genes combined with antibiotic resistant genes has tried to overcome the both toxic antibiotics and metalions causing Typhoid AMR. Such acquisition spreads salmoniasis in the live stocks (pig, cow, chicken) where toxic soil and water dominate increasing chance of MDR typhoid in human.

Space exploration is demanding longer lasting human missions and water resupply from Earth will become increasingly unrealistic. In a near future, the spacecraft water monitoring systems will require technological advances to promptly identify and counteract contingent events of waterborne microbial contamination, posing health risks to astronauts with lowered immune responsiveness. The search for bio-analytical approaches, alternative to those applied on Earth by cultivation-dependent methods, is pushed by the compelling need to limit waste disposal and avoid microbial regrowth from analytical carryovers. Prospective technologies will be selected only if first validated in a flight-like environment, by following basic principles, advantages, and limitations beyond their current applications on Earth. Starting from the water monitoring activities applied on the International Space Station, we provide a critical overview of the nucleic acid amplification-based approaches (i.e., loop-mediated isothermal amplification, quantitative PCR, and high-throughput sequencing) and early-warning methods for total microbial load assessments (i.e., ATP-metry, flow cytometry), already used at a high readiness level aboard crewed space vehicles. Our findings suggest that the forthcoming space applications of mature technologies will be necessarily bounded by a compromise between analytical performances (e.g., speed to results, identification depth, reproducibility, multiparametricity) and detrimental technical requirements (e.g., reagent usage, waste production, operator skills, crew time). As space exploration progresses toward extended missions to Moon and Mars, miniaturized systems that also minimize crew involvement in their end-to-end operation are likely applicable on the long-term and suitable for the in-flight water and microbiological research.

Lake Manzala, the largest of the northern Delta lakes of Egypt, has a great economic importance as a major natural resource of fish and salt. Unfortunately, the lake is suffering from the high inputs of pollutants from industrial, domestic, and agricultural sources. The present study aims to develop the proposed water quality management scenarios to assess and control lake pollution, the pollution sources as well as the pollution spread from the lake to the connected Mediterranean Sea. To apply study methodology, the work tasks divided into two main parts, the first part involved in modelling the lake environments by using Delft3D-WAQ hydrodynamic and water quality model to study the current status and predict the dynamic state of the Lake. This model was calibrated and validated by using various water quality datasets to simulate different scenarios. In the second part, the required lake water quality improvement scenarios were developed to solve the lake water quality problems. The study results showed that the first three developed scenarios that focusing on treatment drain effluent using primary, secondary treatment and surface wetland techniques respectively have a limited efficiency on lake water quality improvement. While the fourth scenario that involved on using biological biofilm techniques can improve lake water quality parameters. Moreover, the fifth scenario that proposed adding a new artificial inlet has a limitation due to the noted increases in lake salinity levels. The sixth scenario that proposed a diversion of some drains can improve lake water quality parameters but it can lead to a decrease in Lake water level. From water quality view point, the last scenario that applying a combination biological biofilm activated technique and also adding a new artificial inlet at northern lake region can represent the optimum scenario. Hopefully, this research will preserve the lake environment and contribute to the benefit of the man health as well. This approach could be extended to the hydrodynamic studies in similar large, shallow lakes anywhere in the world.

The preparation of immobilized graphene–based photocatalyst layers is highly desired for environmental applications. In this study, the preparation of an immobilized reduced graphene oxide (rGO)/TiO₂ composite by electrophoretic deposition (EPD) was optimized. It enabled quantitative deposition without sintering and without the use of any dispersive additive. The presence of rGO had beneficial effects on the photocatalytic degradation of 4-chlorophenol in an aqueous solution. A marked increase in the photocatalytic degradation rate was observed, even at very low concentrations of rGO. Compared with the TiO₂ and GO/TiO₂ reference layers, use of the rGO/TiO₂ composite (0.5 wt% of rGO) increased the first-order reaction rate constant by about 70%. This enhanced performance was due to the increased formation of hydroxyl radicals that attacked the 4-chlorophenol molecules. The direct charge transfer mechanism had only limited effect on the degradation. Thus, EPD-prepared rGO/TiO₂ layers appear to be suitable for environmental application.

Literature data on Legionella spp. presence in houses water networks have been increasing during the last years, but epidemiological reports assert a high incidence of Legionnaires’ disease infection in Italy. Updating our previously published data, we report a five-year survey on Legionella spp. colonization in 235 buildings with an independent hot water production (IB); 82 buildings with a central hot water production (CB); and 58 buildings with a solar thermal system for hot water production (TB). In all the 375 buildings Legionella spp. was researched in hot and cold water samples and microbiological potability standards of cold water were evaluated. Legionella spp. was detected in 27% of the water networks, mostly in CB and TB. We detected correlations between the presence of bacteria and some physical-chemical parameters (low chlorine level and optimal temperature for Legionella spp. growth). Cold water resulted free from microbiological hazards, except for coliform bacteria isolated in three separate cases, and Legionella spp., detected when cold water temperature was about 20°C. After a five-year survey we confirm the presence of a Legionnaires’ disease risk and the need of training programs for all the workers involved in residential water systems management.

(1) Background: Water resources at Chia lagoon experience possible threat to its sustainability. Communities are seeking alternatives to improve water quality at the lagoon. The study evaluated the extent at which local communities are WTP to improve water quality at Chia lagoon and the influencing factors. (2) Methods: A study was conducted at Chia lagoon, Western Part of Lake Malawi from November, 2015 to March, 2016. Wide range of data collection approaches such as household surveys, exploratory surveys, focus group discussions, key informant interviews and field observation were employed. A sample of 240 households were selected randomly. Qualitative data was analysed using content analysis. Multivariate logistic regression analysis was used to determine factors influence WTP. (3) Results: Out of 240 respondents, 57.4% expressed WTP. Multivariate logistic regression analysis demonstrated significant (P<0.01 or P<0.05) relationship between demographic (Gender, age, literacy level), social-economic (Land ownership, main agriculture water source and income) and institution (civic education and social network, extension, water user rights) factors and WTP. (4) Conclusion: The findings from this study provide significant clues for further research and baseline information for local government and local communities in development of more effective and holistic approaches to improve water quality.

Recently a new class of experiments in the field of surface gravity waves has emerged. These experiments serve as demonstration of an analogy to a broad variety of phenomena in optics and quantum mechanics. In particular, experiments involving Airy water-wave packets were carried out. The Airy wave packets have attracted tremendous attention in optics and quantum mechanics owing to their unique properties, spanning from an ability to propagate along parabolic trajectories without spreading, and to accumulating a phase that scales with the cubic power of time. Non-dispersive Cosine-Gauss wave packets and self-similar Hermite-Gauss wave packets, also well known in the field of optics and quantum mechanics, were recently studied using surface gravity waves as well. These wave packets demonstrated self-healing properties in water wave pulses as well, preserving their width despite being dispersive. Finally, this new approach also allows to observe diffractive focusing from a temporal slit with finite width.

There is still a lack of a clinical test to reliably identify patients with Parkinson’s disease (PD) being at risk for aspiration. In this prospective, controlled, cross-sectional study we assessed if swallowing speed for water is a useful clinical test to predict aspiration proven by flexible endoscopic evaluation of swallowing (FEES). Due to this we measured the swallowing speed for 90 ml water in 115 consecutive and unselected PD outpatients of all clinical stages and 32 healthy controls. Average swallowing speed was lower in patients compared with controls (6.5 ± 3.9 ml/s vs. 8.5 ± 3.2 ml/s; p < 0.01). The disease-independent widely used threshold of < 10 ml/s showed insufficient sensitivity of 88% and specificity of 19% with unacceptable false-positive rates of 63% for patients and 69% for controls. Receiver operating characteristic (ROC) analysis was carried out to define a suitable cut-off value for detection of aspiration of water (area under the curve 0.72, p < 0.001) in PD patients. The optimized cut-off value was 5.5 ml/s with a sensitivity of 69% and a specificity of 64%. Overall, measuring swallowing speed is prone to methodological errors and not suitable as a screening instrument to predict aspiration in PD patients.

Descriptive research design was used to select 200 respondents (i.e., 100 from each study places) following purposive sampling technique on two study areas (Market; Living). Personal observation and interview with retailers were done to triangulate the collected data from the formal survey. The collected data was analyzed using SPSS version 20 software program. Descriptive statistical measurements, Index and multinomial regression model was calculated to assess the relationship between customers point of emphasis during packaged water buying and respondents demographic variables. Majority of the respondent who frequently purchase packaged water generated a monthly income between 5000 and 10000 Birr. Television and radio was ranked first compare to other Media. Living place customers were more health concerned as compared to market place customers. Market place customer’s primarily give emphasis to price of packaged water. Almost all (97%) customers did not have the awareness towards packaged water standards. Only 86(43%) of the total respondents checked the chemical composition, of which 74(85%) of the respondents did not understand it. Customers sex, educational level and health status showed significant relationship with choice of packaged water quality -1.42(p<0.05), price -2.45(P<0.01) and health status -1.80(P<0.05) in market place and living places, respectively.

Pb found in rain water is not only caused by tin roof on houses but also caused by the pollution of industrial activities, vehicles and land clearing activity by fire. Pb pollutant dissolves and enters into rain water storages and it’s consumed as drinking. Pb can cause bad impact to human, for example disruption of enzyme, anemia and low intelligence. The purposes of this research are (1) to evaluate Pb, pH and turbidity level in rain water, (2) to analyze the effectiveness of mollusk sand filtration and the absorption of activity carbon to decrease Pb, turbidity and pH, and (3) to analyze the correlation of Pb, length of stay and smoking habit on public health. This research is an experimental by using pre and post test designs with control and observational by using cross sectional design. The research was conducted in urban and rural areas of Pontianak and Kubu Raya regency. The sampling was done in determining the number of samples of Pb, pH and turbidity in rain water. The analyzing the data by using computer program. The results show that: (1) the average of Pb, pH and turbidity level before treatment is considered high at 131.7 µg/L on Pb, turbidity at 20 NTU and low pH at 5.2. After the treatment was the Pb has decreased to 0.71 µg/L and turbidity has to 5.66 NTU, pH to 6.9 and (2) Rain water treatment is very effective to decrease Pb for 99.4% and turbidity for 72%, and (3) there is a correlation among Pb found in rain water, length of stay and smoking activity to public health. Recommends that: the residents of Pontianak and Kubu Raya to process rain water before consuming. The rain water treatment can be done by applying mollusk sand filtration and absorption of active carbon.

Abstract: Currently, thermal power is the largest source of power in the world. Although the impacts of climate change on cooling water sufficiency in thermal power plants have been extensively assessed globally and regionally, their economic consequences have seldom been evaluated. In this study, the Asia-Pacific Integrated Model Computable General Equilibrium model (AIM/CGE) was used to evaluate the economic consequences of projected future cooling water insufficiency on a global basis, which was simulated using the H08 global hydrological model. This approach enabled us to investigate how the physical impacts of climate change on thermal power generation influence economic activities in regions and industrial sectors. To account for the uncertainty of climate change projections, five global climate models and two representative concentration pathways (RCPs 2.6 and 8.5) were used. The ensemble-mean results showed that the global gross domestic product (GDP) loss in 2070–2095 due to cooling water insufficiency in the thermal power sector was −0.21% (−0.12%) in RCP8.5 (RCP2.6). Among the five regions, the largest GDP loss of −0.57% (−0.27%) was observed in the Middle East and Africa. Medium-scale losses of −0.18% (−0.12%) and −0.14% (−0.12%) were found in OECD90 (the member countries of the Organization for Economic Co-operation and Development as of 1990) and Eastern Europe and the Former Soviet Union, respectively. The smallest losses of −0.05% (−0.06%) and −0.09% (−0.08%) were found in Latin America and Asia, respectively. The economic impact of cooling water insufficiency was non-negligible and should be considered as one of the threats induced by climate change.

β-dicalcium silicate (β-Ca₂SiO₄, or β-C₂S in cement chemistry notation) is one of the most important minerals in cement. An improvement of its hydration rate would be the key point for developing environmentally friendly cements with lower energy consumption and CO₂ emissions. However, there is a lack of fundamental understanding on the water/β-C₂S surface interactions. In this work we aim to evaluate the water adsorption on three β-C₂S surfaces at the atomic scale using density functional theory (DFT) calculations. Our results indicate that thermodynamically favorable water adsorption takes place in several surface sites, with a broad range of adsorption energies (−0.78 to −1.48 eV), depending on the particular mineral surface and adsorption site. To clarify the key factor governing the adsorption, the electronic properties of water at the surface were analyzed. The partial density of states (DOS), charge analysis, and electron density difference analyses suggest a dual interaction of water with β-C₂S (100) surface: a nucleophilic interaction of the water oxygen lone pair with surface calcium atoms, and an electrophilic interaction (hydrogen bond) of one water hydrogen with surface oxygen atoms. Despite the elucidation of the adsorption mechanism, no correlation was found between the electronic structure and the adsorption energies.

This study assessed the hydrological performance and runoff water quality of 12 green roof (GR) modular systems located at the Universidad de los Andes campus (Bogotá, Colombia). Based on 223 rainfall events spanning a 3-year period, average rainfall retention was 85% (SD = 25%). T-tests, Welch Test, multiple linear regressions and correlation analysis were performed in order to assess the potential effect of air temperature, substrate type, vegetation cover, relative humidity, antecedent dry weather period (ADWP), rainfall duration and rainfall maximum intensity. In some cases, GR design variables (i.e. growing media and type of vegetation) were found to be significant for describing rainfall retention efficiencies and, depending on the GR type, some hydrological variables were also correlated with the rainfall retention. Rainfall and GR runoff were monitored for Total Kjeldahl Nitrogen (TKN), Nitrates, Nitrites, Ammonia, Total Phosphorus (TP), Phosphates, pH, Total Dissolved Solids (TDS), Total Suspended Solids (TSS), Color, Turbidity, Biological Oxygen Demand (BOD), Chemical Oxygen Demand (COD), Total Coliforms, metals and Poliaromatic Hydrocarbons (PAHs). The results obtained confirmed that GR systems have the ability to neutralize pH, but are source of the rest of the aforementioned parameters, excluding PAHs (with concentrations below detection limits), Ammonia, TSS, Se and Li, where differences with reference values (rainfall and plastic panel runoff) were not statistically significant. Substrate type, event size and rainfall regime are relevant variables for explaining runoff water quality.

Hot rolling tests of a low-alloy steel were conducted at a rolling temperature of 850 ℃ under different lubrication conditions, including benchmarks (dry condition and water) and water-based nanolubricants containing different concentrations of nano-TiO₂ from 1.0 to 8.0 wt%. The effects of nanolubricants on rolling force, surface roughness, thickness of oxide scale and microstructure were systematically investigated through varying nano-TiO₂ concentrations. The results show that the application of nanolubricants can decrease the rolling force, surface roughness and oxide scale thickness of rolled steels, and refine ferrite grains. In particular, the nanolubricant containing an optimal concentration (4.0 wt%) of nano-TiO₂ demonstrates the best lubrication performance, owing to the synergistic effect of lubricating film, rolling, polishing and mending generated by nano-TiO₂.

Climate change such as sea level rise, change in temperature, precipitation, and storminess are expected to impact significantly coastal lagoons. The nature and magnitude of these impacts are uncertain. The objective of the research is to determine the climate change impacts on mixing and circulation at Songkhla lagoon, Thailand. Songkhla lagoon is the largest lagoonal water resource in Thailand and Southeast Asia. The lagoon is a combined freshwater and estuarine complex of high productivity which represents an extraordinary combination of environmental resources believed to be unique in the region. This work is part of a Climate Change impact assessment framework. It is the validation phase (step 5) of the framework applying a case study. Delft 3D was used to simulate CC scenarios in the climate downscaling models, part of the previous framework steps. These results were compared to the current conditions to determine the main changes in mixing and circulation in the coastal lagoon. Three indicators were applied to quantify the impacts: flushing time, salinity intrusion and stratification. The results suggest an increase in water velocities at the inlet in future scenarios and a decrease of flushing time. Salinity and stratification showed more complex changes in futures scenarios.

Species data of 249 National Nature Reserves in China was used to identify potential underlying drivers of latitudinal gradients in plant diversity. We used generalized linear models (GLMs) to assess the correlations between predictor and response variables. We also used SAM (Spatial Analysis in Macroecology) to eliminate autocorrelation along each of the 249 studied locations. We used the Akaike information criterion (AICc; Montoya et al. 2007) to select the independent variables were those included in the best models from different combinations of climate, habitat and animal variables. Variance partitioning was used to decompose the variation in plant richness across different taxonomic levels among the three groups of predictors. We found that: Total plant species, gymnosperms, angiosperms and ferns showed significant latitudinal trends in richness (p < 0.001). Water-energy and habitat variables generally explained more variation in richness across different plant groups than did animal richness. Annual precipitation was selected as the best water-energy variable across different taxonomic plants groups, soil PH and elevation range were selected as the best habitat variables across different taxonomic plant groups. The independent effects of habitatvariables were higher than that of water-energy and animal variables across different taxonomic plants groups. Water-energy, habitat heterogeneity, and animal variables explain 48.8% of the variation in total species richness, 28.2% in gymnosperm richness, 44.2% in angiosperm richness, and 38.9% in fern richness.Plants showed significant latitudinal trends in richness (p < 0.001). Water-energy and habitat variables generally explained more variation in richness across different taxonomic plants groups than did animal variables. The independent effects of habitat variables were higher than those of water-energy and animal variables across different taxonomic plants groups.

Analysis of water resources of this area was carried out in order to assessing the water quality by determining the concentrations of Cations, Anions, Heavy metals, Trace elements, PH, Alkalinity, Total Dissolved Solids and microbial loads in water samples. Ten (10) water samples were collected from the study area - samples each of rain water, two pond waters - 1 and 2, stream water, four (4) hand-dug wells, hand pump water and a motorized borehole. The results obtained were compared with WHO standards and it showed that all the cations in water samples are within the limits. The water samples at locations B, E, F, G, H, I, and J have high alkalinity and HC0^-₃ content. The heavy metals (Pb, Ni and Cd) and trace elements (Fe and Cu) are dominantly high in the surface waters. Microbiological substances in the water samples from the study area revealed indicator organisms higher than the WHO standard for drinking water. Samples obtained from location G, I and J recorded an absence of E. coli and are fit for human consumptions but needed to be treated due to high MPN (Most Probable Number) index of viable microorganisms as against WHO standard. This research showed that the water resources of the study area are gradually polluted and in the near future may not be good for drinking.

The purpose of the present research was to analyze the available data on river restoration projects. As the framework of our study, we conducted a structured international survey. We asked selected entities and experts from among those responsible for river restoration in European countries about the details and costs of European Union river restoration projects. We examined 119 river restoration projects that were implemented in Europe between 1989 and 2016; some of the projects were still ongoing. We observed that the number of river restoration projects has been increasing since 1989, which expresses society’s growing interest in improving the quality of aquatic environments. We revealed that 56% of these European river restoration projects have been implemented by dedicated entities and stakeholders, not as part of any structured, larger-scale river restoration policy; this indicates that most European countries do not have integrated plans for river restoration. Our analysis showed that 52% of the projects analyzed have been designed and implemented without the participation of local stakeholders. It also showed that the budgets for river restoration projects did not differ significantly across various time horizons from 1981 to 2016. In our study, the average cost of restoring 1 ha of an average European river was 310 000 EUR (or 195 000 EUR if 4 outlying values are excluded). Considering these projects’ permanent assets and including their amortization, for European river systems, we calculated the average unit price of a river restoration’s value in terms of ecosystem meta-service to be 7 757 EUR · ha^-1 · year^-1 (4 875 EUR · ha^-1 · year^-1 if 4 outlying values were excluded).

Bacteria play a key role in both human health and disease. One of the most prevalent harmful bacteria is E. coli which is responsible for several illnesses ranging from diarrhea, stomach cramp and fever. In this work we explore the application of moderate electric or magnetic fields for treating deionized water that is contaminated with E. coli. We found that moderate alternating electric (AC) fields (10 V/cm to 1kV/cm) and moderate static magnetic fields (10 to 65 mT) can significantly inactivate E. coli by up to 90% or more. This provides the possibilities of developing a low cost and a practical bacteria inactivation technique using electric or magnetic fields.

Diseases caused by contaminated water consumption and poor hygiene are among the leading cause of death in children, the elderly and people with compromised immune system. The present study aims to assess the drinking water quality of some selected drinking water sources in the chosen study area using water quality index (WQI). Samples of drinking waters were collected from four different sources—river, sachet (packaged), borehole and well in Jabi, Abuja, Nigeria for physicochemical and bacteriological analyses using standard methods. With the exception of pH, river water had the highest content of all the physicochemical parameters examined. Some of the physicochemical parameters such as temperature and pH determined in this study were mostly within the World Health Organization (WHO) standard. The bacteriological analyses revealed that the highest total viable counts of 1.54 (0.12) × 10² (cfu/mL) were obtained in the river sample while the least values of 0.03 (0.00) × 10² (cfu/mL) were obtained in the sachet water. Three bacterial isolates of Escherichia coli, Pseudomonas spp and Aeromonas spp were isolated from well water while Pseudomonas spp and Proteus spp were isolated from borehole water. All other bacteria were isolated from the river. The study demonstrates that the safest drinking water source in Idu district, Jabi, Abuja is the sachet/packaged water while the least safe is the river water due to the presence of significant opportunistic pathogens. The results of this study are beneficial for water quality management and could be used for low-cost effective water quality assessment in Jabi.

Development of the self-cleaning and anti-fogging superhydrophobic coating for aluminum surfaces which is durable in the aggressive conditions has raised tremendous interest in materials science. In this work, by employing chemical etching technique with mixture of hydrochloric and nitric acid, followed by passivation with lauric acid, superhydrophobic aluminum surface was synthesized. The surface morphology analysis reveals the presence of rough microstructures on coated aluminium surface. Superhydrophobicity with water contact angle of 170 ± 3.9° and sliding angle of 4 ± 0.5° is achieved. Surface bounces off the high speed water jet, indicating excellent water-repellent nature of coating. It is also continuously floated on water surface for several weeks, showing excellent buoyancy nature. Additionally, coating maintains its superhydrophobicity after undergoing 100 cycles of adhesive tape peeling test. Its superhydrophobic nature withstands 90° and 180° bending, and repeated folding and de-folding. Coating exhibits the excellent self-cleaning property. In low temperature condensation test, almost no accumulation of water drops on the surface, showing the excellent anti-fogging property of coating. This approach can be applied to any size and shape of aluminium surface and hence has great industrial applications.

Diseases in articular cartilages have affected millions of people globally. Although the biochemical and cellular composition of articular cartilages is relatively simple, there is the limitation in self-repair ability of cartilage. Therefore, developing the strategies for cartilage repair is very important. Here, we reported a new manufacturing process of water-based polyurethane based photosensitive materials with hyaluronic acid and applied the materials for 3D printed customized cartilage scaffolds. The scaffold has high cytocompatibility and is one that closely mimics the mechanical properties of articular cartilages. It is suitable for culturing human Wharton's jelly mesenchymal stem cells (hWJMSCs) and the cells showed an excellent chondrogenic differentiation capacity. We consider that the 3D printing hybrid scaffolds may have potential in customized tissue engineering and facilitate the development of cartilage tissue engineering.

The binding of actinide ions (Am(III) and U(VI)) in aqueous solutions by hybrid silica-hyperbranched poly(ethylene imine) nanoparticles (NP) and xerogels (XG) has been studied by means of batch experiments at different pH values (4, 7 and 9) under ambient atmospheric conditions. Both materials present relatively high removal efficiency at pH 4 and pH 7 (&gt; 70%) for Am(III) and U(VI). The lower removal efficiency for the nanoparticles is basically associated with the compact structure of the nanoparticles and the lower permeability and access to active amine groups compared to xerogels, and the negative charge of the radionuclide species formed under alkaline conditions (e.g. UO2(CO3)34- and Am(CO3)2-). Generally, the adsorption process is relatively slow due to the very low radionuclide concentrations used in the study and is basically governed by the actinide diffusion from the aqueous phase to the solid surface. On the other hand, the adsorption is favored with increasing temperature assuming that the reaction is endothermic and entropy-driven, which is associated with increasing randomness at the solid-liquid interphase upon actinide adsorption. To the best of our knowledge, this is the first study on hybrid silica-hyperbranched poly(ethylene imine) nanoparticle and xerogel materials used as adsorbents for americium and uranium at ultra-trace levels. Compared to other adsorbent materials used for binding americium and uranium ions, both materials show far higher binding efficiency. Xerogels could remove both actinides even from seawater by almost 90%, whereas nanoparticles could remove uranium by 80% and americium by 70%. The above, along with their simple derivatization to increase the selectivity towards a specific radionuclide and their easy processing to be included in separation technologies, could make these materials attractive candidates for the treatment of radionuclide/actinide contaminated water.

For water-stressed regions like Iran improving the effectiveness and productivity of agricultural water-use is of utmost importance due to climate change and unsustainable demands. Therefore, a hydro-economic model has been developed here for the Zarrine River Basin with the central concept of that demands are value-sensitive functions, where quantities of water-uses at different locations and times have a changeable economic benefits. To do this, the potential crop yields and the surface and groundwater resources, especially Boukan Dam inflow are simulated using the hydrologic model, SWAT, based on predicted climatic scenarios i.e. quantile mapping-downscaled projections. Then, to allocate the agricultural water based on the agro- economic crop water productivity (AEWP) of crops, a basin-wide water management tool, MODSIM, is customized. Next, a simulation- optimization model has been developed using a coupled CSPSO-MODSIM, to optimize the total AEWP, considering climatic impact and crop pattern scenarios, for 2020-2038, 2050-2068 and 2080-2098 periods. Finally, the optimum crop pattern and crop water irrigation depths are presented for different RCPs and periods. The results indicated that this approach will improve considerably the AEWPs and decrease the agricultural water-use up to 40%. Thus, this integrated model is able to support water authorities and other stakeholder in a water-scarce basin, as is the study area.

Cyanobacteria are ubiquitous phototrophic bacteria that inhabit diverse environments across the planet. They dominate many eutrophic lakes impacted by excess nitrogen (N) and phosphorus (P) forming dense accumulations of biomass known as cyanobacterial harmful algal blooms or cyanoHABs. Their dominance in eutrophic lakes is attributed to a variety of unique adaptations including N and P concentrating mechanisms, N fixation, colony formation that inhibits predation, vertical movement via gas vesicles, and the production of toxic or otherwise bioactive molecules. While some of these molecules have been explored for their medicinal benefits, others are potent toxins harmful to humans, animals, and other wildlife known as cyanotoxins. In humans these cyanotoxins affect various tissues, including the liver, central and peripheral nervous system, kidneys, and reproductive organs among others. They induce acute effects at low doses in the parts-per-billion range and some are tumor promoters linked to chronic diseases such as liver and colorectal cancer. The occurrence of cyanoHABs and cyanotoxins in lakes presents challenges for maintaining safe recreational aquatic environments and the production of potable drinking water. CyanoHABs are a growing problem in the North American (Laurentian) Great Lakes basin. This review summarizes information on the occurrence of cyanoHABs in the Great Lakes, toxicological effects of cyanotoxins, and appropriate numerical limits on cyanotoxins in finished drinking water.

This study aims to evaluate how the operational procedure adopted for the pellets placement and the exposure to subsurface conditions influences the mechanical integrity of bentonite plugs used as barrier elements in the abandonment of petroleum wells. To this end, two methodologies were used to obtain the plugs: from the first methodology, the pellets were immersed in diesel or olefin, which are proposed as displacement fluids in offshore operations, and then, hydrated in deionized water; in the second methodology, representative of onshore operations, the pellets were directly hydrated in deionized water. After that, the plugs were tested by compression and adhesion tests. These mechanical tests were also carried out for test specimens obtained from plugs exposed to four formulations of synthetic formation waters. The results obtained demonstrated that the previous contact with olefin adversely affects the mechanical stability of bentonite plugs, while plugs formed from pellets immersed in diesel presented satisfactory mechanical properties. The mechanical properties of onshore plugs attested the highly successful performance of these elements, once its compressive strength was minimally impacted by exposure to formation waters and more pronounced reductions were observed only in the adhesion properties after the contact with higher salinity formation waters.

Iron tailings are solid waste generated after the mining of iron mines, which have caused serious damage to the surrounding ecology and environment and have attracted widespread attention. By analyzing the formation causes, main components, and environmental effect mechanisms of iron tailings, the article systematically elaborates on the degree and mechanism of the harm of iron tailings to water bodies, atmosphere, soil, and ecosystems, and evaluates its impact on human health and sustainable development of society. On this basis, specific prevention and control measures have been proposed to reduce iron tailings emissions, realize resource recycling, and restore ecosystems. Research shows that iron tailings containing heavy metals can widely pollute the environment through dissolution and migration, and have significant biological toxicity effects. The research results can provide a theoretical reference for decision-making departments to formulate scientific and reasonable iron tailings disposal and ecological protection policies. It is recommended to strengthen specific research on the infiltration of toxic and harmful components in tailings in the future, and develop efficient and stable solidification technology, and vegetation-microbial joint restoration models to further reduce the ecological and environmental risks of iron tailings.

Recent climate change and water pollution has affected algal diversity resulting in emergence of more tolerant species. They can be the indicators of water quality, pollution and seasonal changes. Present study revealed the green algal diversity and distribution pattern according to water parameters and season in the Lucknow City, India. The water sample were collected from seven sites within Lucknow and outskirts. The occurrence of a total of 36 taxa of green algae belonging to 11 genera are recorded. It has been observed that less polluted water is dominated by Spirogyra; where conductivity, TDS and salinity of water were low. Whereas the more polluted water was dominated by desmids. Dominance index was found highest in site 4 (0.61), where only three taxa were identified; whereas the lowest (0.13) was measured in site 1, where nine taxa were identified. This study also recorded several algal taxa for the first time from Lucknow.

The River Habitat Survey (RHS) is a method for assessing the conditions of a river channel and valley, taking into account hydromorphological factors, and assessing the degree of naturalness or the degree of anthropogenic alteration within the channel and valley based on physical and landscape data. The hypothesis tested in this study was that the quality of river habitats demonstrated using the RHS should translate into the composition of their fauna. We investigated aquatic bugs (Heteroptera Aquatica), which are a group with considerable dispersal abilities and, at the same time, composed of stenotopic species associated with a particular environment as well as of eurytopic elements inhabiting a wide range of environments (REF). The research was carried out in a small lowland river, the River Krąpiel (north-western Poland) at 6 sites with 43 sub-sites included. Our analyses suggest the RHS method can predict the composition and quality of the aquatic bug fauna inhabiting a given river. Indicators of river habitat quality (HQA and RHQ) will be associated with different habitat types depending on the geographic location and type of river, once indicating habitats associated with the mainstream river and mineral substrate (mountain and small lowland rivers) and at other times habitats covered by vegetation with relatively slow water flow (large and medium lowland rivers). Therefore, RHS may be a good method for estimating the water bug fauna, linking it to the size and character of the river.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

The opportunities and advantages of implementing Artificial Intelligence (AI) and Machine Learning (ML) to optimize the process control of wastewater treatment in the Oil and Gas industry are discussed in this work. Discussion is centered around five major points: 1) Various types of Oil and Gas wastewater (Sour, Oily, Produced) and industry standards/methods for treatment, including specific case studies and challenges when treating certain wastewater. This section aims at the common types of wastewater in the Oil and Gas industry and how they are generally treated. 2) How AI/ML has been implemented in wastewater treatment in various industries; summary of which AI/ML languages were used along with a brief overview of how they work. This article focused on an understanding of the specific case studies and AI explanations to understand the effectiveness of wastewater treatment using AI/ML. 3) AI that is currently implemented in Oil and Gas such as personal protective equipment (PPE), smartwatches radiofrequency identification etc. This showed that AI/ML already plays a successful role in the Oil and Gas industry and has proven to help optimize many processes and components. Many of these AI/ML implementations are now industry standards and have greatly benefitted the industry. This section demonstrates that the implementation and the use of AI/ML have been proven to be a successful endeavor and that expanding the role of AI/ML would be beneficial. 5) Using the established points from the previous sections the paper outlines why AI/ML is ideal for Oil and Gas wastewater treatment; this argument centers around fit-for-purpose treatment, and the possible uses of the treated water. A determination of the best-suited AI languages, possible implementation scenarios, and how this would shift the way Oil and Gas industries treat and approach wastewater is presented to the reader.

In recent years, Global Navigation Satellite System reflectometry (GNSS-R) has been explored as a methodology for inland water body characterization. However, thorough characterization of the sensitivity and behavior of the GNSS-R signal to inland water bodies is still needed to progress this area of research. In this paper, we characterize the uncertainty associated with Cyclone Global Navigation Satellite System (CYGNSS) measurements on the determination of river width. The characterization study uses simulated data from a forward model that accurately simulates CYGNSS observations of mixed water/land scenes. The accuracy of the forward model is demonstrated by comparisons to actual observations of known water body shapes made at particular measurement geometries. Simulated CYGNSS data is generated over a range of synthetic scenes modeling a straight river subreach, and the results are analyzed to determine a predictive relationship between the peak SNR measured over the river subreaches and the river widths. An uncertainty analysis conducted using the predictive relationship indicates that for simplistic river scenes, the SNR over the river is predictive of the river width to within +/-5m. The presence of clutter (surrounding water bodies) within ~500m of the river causes perturbations in the SNR measured over the river that can render the river width retrievals unreliable. The results of this study indicate that under idealized conditions, GNSS-R data is able to measure river widths as narrow as 160m with high accuracy.

The Eastern Kunlun Fault Zone (EKFZ) is located in a seismic blank area. This study investigates the hydrogeochemical characteristics of varied-temperature springs in the EKFZ to understand the relationship between fractures, fluids and earthquakes. It aids in establishing their induction mechanisms and assists in monitoring the earthquake precursors of the EKFZ. In this study, the main elements, trace elements, hydrogen and oxygen isotopes and strontium isotopes of 23 varied-temperature springs in the EKFZ were analyzed. The results reveal the source of groundwater recharge, hydrochemical types, mineral saturation, and for a select few springs indicative of geothermal activity, collected geothermal reservoir temperatures. The study also explores the relationship between earthquakes and springs, identifying sensitive chemical indicators. Based on continuous monitoring at Maqu Station, we found that before the occurrence of the Maerkang Ms 6.0 earthquake, the concentration of Cl− rose by 2.9 times, and 46 days before the Gande earthquake (Ms = 4.7), the concentrations of Na+ and SO42− significantly increased. Finally, a conceptual model of the hydrogeochemistry of springs is presented to describe the groundwater circulation in the study area. This research is of great significance for the analysis of fluid geochemistry in this area and for assessing the seismic hazards of the EKFZ.

A very detailed water budget was conducted on Lake Trafford in southern Florida. The inflow was dominated by surface-water influx via five canals (61%) with groundwater influx constituting 12% and direct rainfall 27%. Lake discharge was dominated by sheet-flow (69%) and evapotranspiration (30.5%) with groundwater recharge of the hydraulically connected unconfined aquifer accounting for only 0.5%. Removal of 30 M tons (4.4 x 106 m3) of organic sediment impacted groundwater influx, causing enhanced groundwater flows into the deeper parts of the lake and mixed flows along the banks creating a rather unusual pattern. The large number of groundwater seepage meters used during the investigation led to a very reliable set of measurements with occasional failure of only a few meters. A distinctive relationship was found between the wet season lake stage, heavy rainfall events and pulses of exiting sheet-flow from the lake. Estimation of the evapotranspiration loss using data collected from a weather station on the lake allowed the use of three different models which, when averaged, produced results comparable to Lake Okeechobee (southern Florida). A limitation of the investigation was the inability to directly measure sheet-flow discharges, which had to be estimated as a residual within the calculated water budget.

This work presents a numerical study on atmospheric sound propagation over rough water surfaces. A method to generate pseudorandom sea profiles consistent with sea wave spectra is presented. The proposed method is suited to capture the logarithmic nature of the energy distribution of the waves. Sea profiles representing fully developed seas for sea states 2, 3, 4 and 5 are generated from the Elfouhaily et al. (ECKV) sea wave spectra. Excess attenuation caused by refraction and surface roughness is predicted with a parabolic equation (PE) solver. A novel method to estimate equivalent effective impedance based on PE predictions at different sea states is presented. Parametric expressions using acoustic frequency and significant wave height are developed for effective surface impedances. In this work, sea surface roughness is on a scale comparable to the acoustic wavelength. Under this condition, the acoustic scattering is primarily incoherent. This work shows the limitations of using an equivalent surface impedance in such incoherent scattering cases.

Nature-Based Solutions (NBSs) can help to achieve multiple Water-Ecosystem-Food Nexus Do-main Objectives & Nexus Resilience Qualities, facilitating the transition to more resilient agrifood systems and providing an evidence base for a broader Nexus policy dialogue. This paper de-scribes the stepwise methodology developed in the EU-funded LENSES project to carry out a comprehensive analysis of NBSs in 6 pilot areas in 5 Mediterranean countries, and presents the results of NBSs implementation in 4 pilot areas, highlighting obstacles and opportunities. The methodology includes the development of an analytical evaluation framework and of a com-prehensive catalogue of Nexus-related NBSs, whose suitability needs to be assessed at the local level to achieve better use of protected/natural ecosystems, increase the sustainability and mul-tifunctionality of managed ecosystems and design and manage novel ecosystems. Subsequently, in a collective learning process which supported the operationalisation of the WEF Nexus, NBSs were identified that address specific contextual vulnerabilities, improve water distribution and enhance food security, while preserving ecosystems and supporting adaptation to climate change. The added value of the proposed methodology lies in the multi-stakeholder participatory approach to gain in-depth knowledge of local agri-food systems, including their main WEF-related challenges, and to facilitate overcoming barriers to NBS implementation.

The water resources policy under climate change impacts water security, which should ensure enough water of good quality for humans and nature. Integrated water management is the state-of-the-art policy support model that, after 20 years in use, failed to achieve in many countries its primary goal of water bodies' good ecological status. Here, we show that this is due to the substantial externalities the anthropocentric character of the model generates. From the historical analysis, three main results are obtained: 1) the nature-human interplay is always composed of the coexistence of two opposite behaviors of conflict and cooperation; 2) this contradiction is a dialectical, general ontological attribute; 3) on the balance of power between nature and humans, three clusters are identified: i) naturalistic; ii) dualistic; iii) anthropocentric. A novel behaviorist dialectical conflict resolution model can resolve the differences between stakeholders and natural laws. The harmonic symbiosis of humans with nature removes environmental externalities and can lead to sustainable water security. Three case studies from the literature illustrate the merits of the new dialectical model.

Inland waters pose a unique challenge for water quality monitoring by remote sensing techniques due to their complicated spectral features and small-scale variability. At the same time, collecting the high-quality reference data needed to calibrate remote sensing data products is both time consuming and expensive. In this study, we present the further development of a robotic team composed of an uncrewed surface vessel (USV) providing in situ reference measurements and an unmanned aerial vehicle (UAV) equipped with a hyperspectral imager. Together, this team is able to address the limitations of existing approaches by enabling the simultaneous collection of comprehensive in situ data together with high-resolution hyperspectral imagery. We showcase the capabilities of this team using data collected in a north Texas pond during three collections in the fall of 2020. Machine learning models for 13 variables are trained using the data set of paired in situ measurements and coincident reflectance spectra. These models can successfully estimate physical variables, including temperature, conductivity, pH, and turbidity, as well as the concentrations of blue-green algae, colored dissolved organic matter (CDOM), chlorophyll-a, crude oil, optical brighteners and the ions Ca2+, Cl−, and Na+. We extend the training procedure to utilize conformal prediction to estimate 90% confidence intervals for the output of each trained model. The maps generated by applying each trained model to the collected images reveal the small-scale spatial variability within the pond. Additionally, the permutation importance computed for each feature of the trained models highlights the spectral features relevant to each water quality variable.

Based on the analysis of hydrochemical data of 18 samples of shallow groundwater around Hancheng mining area in Guanzhong Basin, Gibbs semi-logarithmic diagram and Piper diagram were used to study the hydrogeochemical behavior of shallow groundwater around Hangcheng mining area in Guanzhong Basin. Chemical composition analysis showed that most of the groundwater was SO₄ · Cl-Ca · Mg type, accounting for 61.1 %. Hydrogen and oxygen isotope data show that groundwater in the study area is recharged by modern precipitation. The main chemical components of most groundwater are Ca²⁺, Mg²⁺, HCO₃^-, Cl^-and SO₄^2-. Ca²⁺, Mg²⁺, and HCO₃^- are mainly dolomite, calcite, and gypsum dissolution precipitation results. Na⁺ and Cl^- originate from the dissolution of halite. The main ion chemistry of shallow groundwater in this area is controlled by rock weathering, and pyrite oxidation is an important factor affecting SO₄^2-concentration. The research results will help analyze the formation mechanism of chemical components and provide some basic data for the evolution of mine water in this area in the future.

Water networks are critical infrastructure components, ensuring the continuous supply of high-quality drinking water to consumers. To secure such water supply, regular maintenance, including the replacement of deteriorating pipelines, is essential. In this study, a methodology has been developed for determining optimal pipeline replacement solutions in water supply systems at water utilities with limited data availability. Hydraulic analysis has been conducted on the segment of 25 km of the water supply network using the free software EPANET. Applying water network optimization, eight pipeline replacement projects according to 13 pre-defined criteria have been identified and evaluated. The paper outlines the methods for evaluating the criteria, including defining specific quantitative limits. The Analytical Hierarchical Process (AHP) method was used in the paper to determine the weights of the criteria. The reason for applying this method refers to problems that involve a set of criteria with a mixed structure, including both quantitative and qualitative aspects. Also, the paper describes the steps of the multi-criteria optimization method VIKOR, used to select the optimal project. This paper, considered as case studie, describes a method, i.e. application of a new principles and an innovative way to solve a problem for developing countries.

A thermal system in very deep Lake Tazawa (maximum depth, 423 m) was investigated by estimating the heat budget. In the heat budget estimate, the net heat input at lake surface and the heat input by river inflow and groundwater inflow were considered. Then, the heat loss by snowfall onto lake surface was taken into account. Meanwhile, lake water temperature was monitored at 0.2 m to the bottom by mooring temperature loggers for more than two years. The heat storage change of the lake from the loggers was calibrated by frequent vertical measurements of water temperature at every 0.1 m pitch by a profiler with high accuracy (± 0.01 °C). The heat storage change (W/m2) obtained by the temperature loggers reasonably accords to that from the heat budget estimate. In the heat budget, the net heat input at lake surface dominates the heat storage change, but the significant heat loss by river inflow sporadically occurred, which is caused by the relatively large discharge from a reservoir in the upper region. How deep the vertical water circulation in the lake occurs in winter was judged by the differences between water temperatures at 0.2 m depth and bottom and between vertical profiles of dissolved oxygen over winter. It is strongly suggested that the whole water circulation does not occur every winter, if any, very weak.

Soil nitrite (NO2‒) is an important reactive intermediate in many nitrogen transformation processes, but it is unstable under acidic conditions. Canonical extraction method of soil NO2‒ with potassium chloride (KCl) solution greatly underestimates its concentration. In order to reflect the concentration more accurately, we optimized the extraction method of soil NO2‒ in this study. Moreover, soil ammonium (NH4+) and nitrate (NO3‒) were also systematically investigated to achieve efficient extraction of soil inorganic nitrogen. The results showed that un-buffered KCl significantly underestimated soil NO2‒ concentration compared to DIW. The highest recovery of NO2‒ was obtained by extracting with DIW at 10 min of oscillation for three soils. Compared with DIW, the concentration of NH4+ and NO3‒ in soil extracted from KCl solution increased significantly. Furthermore, the soil inorganic nitrogen content of extracts stored at 4°C for one day were closer to directly measurements of fresh samples than the other storage methods. Overall, the recommend analysis method for soil NO2‒ was extracted by DIW, oscillated for 10 min, and filtered by a 0.45 µm filter, and soil NH4+ and NO3‒ were extracted with KCl solution and oscillated for 30 min. The extract should be stored at 4°C and analyzed within 24 hours.

Abstract: This study estimates consumers’ willingness to pay (WTP) for sustainability turfgrass attributes such as low-input and stress-tolerance attributes, while considering potential trade-off relationships between aesthetic attributes and sustainability attributes. To address our objectives, our study conducts a choice experiment and estimates two mixed logit models. The first model includes low-input, winter kill, and shade-tolerance attributes as predictor variables, and the second model extends the first model by adding interaction terms between aesthetic and sustainability attributes. Another choice experiment is conducted under water policies with various water rate increase and watering restriction scenarios. Results from the mixed logit models show that overall, higher low-input cost reduction, less winter-damaged, and more shade-tolerance grasses are preferred, the direct effect of aesthetic attributes on consumers’ preference is strong, but the indirect effect represented by the interaction terms are generally statistically insignificant. Our results indicate that consumers like to have a pretty lawn, but no strong consideration is given to the aesthetics of their lawn when selecting low-input and stress-tolerance turfgrasses. Our choice experiment under water policy scenarios suggests that water pricing is more effective than watering restriction in increasing consumer demand for water-conserving turfgrasses.

More water utilities are adopting Aquifer Storage and Recovery (ASR) to balance long-term water supply and demand. Due to large implementation and operation costs, ASR projects need to be optimized, particularly for energy use, which is a major operating expense. This study examines the relationships among energy use, recharge, and recovery at two ASR projects in the western United States. The major finding is an economy of scale for recovery processes, but not for gravity-fed recharge processes. The economy of scale found is as follows: the energy intensity recovered decreases with volume. This suggests it is more energy-efficient to recover large volumes of water in one interval instead of recovering smaller volumes at more frequent intervals. The H2Oaks recovery process experienced a 78% decrease in energy intensity from 0 to 50,000 m3 recovered, while the Sand Hollow site experienced a 43% decrease in energy intensity from 0 to 50,000 m3 recovered. Statistical analyses of the recovery process showed p values lower than 0.0001, R2 values between 0.43 and 0.57, and a RMSE value between 0.55 and 2.1, indicating the presence of a moderate correlation between energy and volume. This economy of scale has been observed in multiple instances in water and wastewater treatment. This finding not only has applications to ASR but also all recovery or recharge wells, whether or not they are paired with each other. Furthermore, this study confirms the need for more reliable and accessible energy data to fully understand the implications of the energy–water nexus.

Milkfish (Chanos chanos) locally called Bangus in the Philippines, is a popular food fish in terms of production and consumption in the Philippines, Indonesia and Taiwan. This study characterized a typical grow-out milkfish farm in the Davao region in terms of socioeconomic profile, farming practices, and simple costs and returns. Three sites were chosen to conduct this study, mainly in Mati, Pantukan and Panabo in Davao region where N=43 farm workers provided information on their daily farming practices. Farms are commonly stocked with 16,000 fingerlings, harvesting occurs after every 6 months with six feeding times in a day. Moreover, workers were paid an average of Php 10,000 per month while the company had a gross income of Php 930,000 per cropping cycle. The feed cost shares 76% of the overall operational cost with a 27% return on investment for the first year of operation. Climate change impacts (e.g. higher sea surface temperature, unpredictable weather and flooding) and deteriorating water quality conditions were seen as bigger threats. Other results showed a positive relationship between stocking density and volume harvested (df=1, MS=0.0907, F=40.13, P=0.000) and income (df=1, MS=0.048, F=21.22, P=0.000). The study also showed the need for cheaper feed substitute and better benefits to farm workers.

Water electrolysis is a highly efficient route to produce ideally clean H2 fuel with excellent energy conversion efficiency and high gravimetric energy density, without producing carbon trace unlike steam methane reforming, and resolves the issues of environmental contamination via replacing the conventional fossil fuel. Of special importance lies in the advancement of highly effective non-precious catalysts for the oxygen evolution reaction (OER). The electrocatalytic activity of an active catalyst mainly depends on the material conductivity, accessible catalytically active sites, and intrinsic OER reaction kinetics, which can be tuned via introducing heteroatom N in the catalyst stricture. Herein, an efficacious nitrogenation of CuS has been accomplished, which was synthesized using hydrothermal procedure, and characterized for their electrocatalytic activity towards OER. The nitrogen-doped CuO@CuS (N,CuO@CuS) electrocatalyst exhibits superior OER activity than pristine CuS (268 and 602 mV), achieving the low overpotential of 240 and 392 mV at a current density of 10 and 100 mA/cm2, respectively, ascribed to the favorable electronic structural modification triggered by nitrogen incorporation. The N,CuO@CuS also exhibits excellent endurance under varied current rates and a static potential response over 25 h stability measured at 10 and 100 mA/cm2.

We evaluated the transcriptional response of interferon (IFN)-related genes in rock bream iridovirus (RBIV)-infected rock bream under high-, low-, or no-mortality conditions induced by different stocking water temperatures. Under the high susceptibility condition (group A, water temperature 26 °C, 100% mortality), only the Mx gene was expressed early, with prolonged expression, and with heavy viral loads of approximately 106–107 major capsid protein gene copies/μL from 4 to 10 days post infection (dpi). However, IRF1, IRF3, IRF8, STAT1, ISG15, PKR, Viperin, GVIN1, IFI44, and ISG56 were activated at later time points (8 dpi) and then quickly decreased (10 dpi). For the low susceptibility condition, the water temperature was set at 23 °C for 7 days (group B) and then reduced to 17 °C. Group B exhibited a 28% mortality rate, in which persistent and effective antiviral responses were observed for long periods of time. In particular, at 20 and 22 dpi, when virus replication was peaked at approximately 107/μL, the expressions of most of the IFN-related genes (IRF1, IRF3, IRF8, Mx, STAT1, ISG15, PKR, Viperin, GVIN1, IFI44, and ISG56) were significantly higher in group B than in the control group. Moreover, prolonged and higher levels of IRF3 (at least 30 dpi), IRF8 (at least 30 dpi), ISG15 (at least 30 dpi), PKR (at least 28 dpi), Viperin (at least 30 dpi), and IFI44 (at least 30 dpi) were also observed in the recovery stage of infection. Under the no-susceptibility condition at 17 °C (0% mortality), significantly elevated levels of IRF3, Mx, ISG15, and PKR were observed mostly until 20 dpi. The findings indicate that RBIV infection can induce an efficient IFN-mediated antiviral immune response in low- and no-susceptibility conditions. The findings could be valuable for effective control of viral pathogens in fish.

Using numerical software to establish a three-dimensional geological model of shield tunneling through fault fracture zones, considering the synchronous grouting effect at the shield tail, the disturbance of various geotechnical structures in the fault fracture zone under deep burial and high water pressure conditions is studied. According to the comparison between the numerical model analysis results and the on-site inspection results of the entire process of Shiziyang B3 section, synchronous grouting at the shield tail is the main reason for the changes in soil and water pressure in the fault fracture zone area. The soil and water pressure changes strongly during shield tunneling, and the maximum excess pore pressure value occurs when the shield tail passes. When the shield tunneling machine is far away, the soil and water stress shows a downward trend. The impact of synchronous grouting decreases with the increase of tunneling distance. Due to the difference in permeability, the variation law of pore pressure in the fault fracture zone is significantly different from the original rock, leading to a faster increase in pore pressure in the fracture zone area and a wider range of influence.

In this study, we have included the water footprint (WF) in the process of optimising animal feed rations. The global footprint of cattle production accounts for the largest share (33%) of the global water footprint of livestock production. Using two homogeneous groups of Limousine Podolian young bulls, two different diets were compared: corn silage feeding (CSF), with corn silage-based diet; and the triticale silage feeding (TSF), with triticale silage-based diet. Silage constituted about 41% and 46% of the feed composition (for CSF and TSF, respectively). Diets were characterised by the same energy and protein content. Despite the lower WF in the TSF group than in the CSF group (7726 vs 8571 l/day/calf respectively), no significant differences were found in animal performances (i.e., daily weight gain and final weight), feed conversion and income over feed costs. These results show that simple production decisions can have a significant impact on water resource. Therefore, the use of triticale silage should be further promoted, especially in world regions with limited water resources where low WF feed formulation is more strategic than elsewhere.

The anthropogenic deterioration of aquatic ecosystems affects water resources due to agricultural malpractices, pollution from domestic septic tanks, recreational activities, and poor watershed management, among others. This study examines the management of Las Curias Reservoir (176,974 m2), San Juan, Puerto Rico, post the 2016 arrival of the invasive aquatic fern Salvinia molesta. In December 2019, a community-led initiative introduced the Cyrtobagous salviniae weevil, an effective biological control agent for S. molesta, and commenced a mechanical removal campaign using an aquatic harvester. Limnological sampling (September 2019 to March 2022) and drone flights were employed to measure physicochemical and floating plant cover changes, respectively, in the reservoir. Monitoring of weevils in the reservoir demonstrated a rapid establishment and dispersal, which resulted in visible damage including browning of plants and eventually sinking of entire mats. By January 29, 2021, 71% (125,652 m2) of the reservoir surface was covered by salvinia. In 2022, the reservoir recorded an average dissolved oxygen concentration of 2.38 mg/L -1 (± 0.021, n = 144), the highest in the study period and indicative of ecosystem recovery. After three years of control efforts, dissolved oxygen, pH, and specific conductance returned to levels recorded prior to Salvinia molesta introduction. This ecosystem recovery, a first in Puerto Rico, could be attributed to an early use of mechanical control and a long-term impact of biological control.

A single geological carbon dioxide (CO2) storage within salinity aquifer as a paramount stratagem in the context of forthcoming CO2 sequestration initiatives. Within the expansive tapestry of terrestrial salinity aquifers in China, replete with nuances in mineral composition and structural diversity, a paradigm distinct from the marine sedimentary basins of North America, a labyrinthine stratigraphic environment of elevated complexity unfolds. Consequently, conspicuous lacunae and insufficiencies manifest within the existing knowledge reservoir pertaining to CO2-water-rock (mineral) reaction mechanisms. Notably, a conspicuous dearth of insights prevails concerning the dissolution kinetics inherent to individual minerals embroiled in these reactions. The present investigation undertakes a scrupulous exploration into the dissolution and erosive processes manifest within four emblematic terrestrial minerals in conjunction with CO2. Furthermore, the study meticulously scrutinizes the evolution of ionic composition and pH within the formation water throughout the trajectory of the geochemical reactions. To accomplish this, a simulation apparatus is configured to emulate conditions germane to temperature, pressure, and mineralization characteristics characteristic of a prototypical salinity aquifer reminiscent of the Daqing oilfield in China. The findings that emerge from this scrutiny reveal that the erosive action of CO2 fluid begets varying degrees of dissolution within the four minerals under investigation. Moreover, our meticulous inquiry lays bare that, in the terminal phases of the reaction process, feldspar precipitates secondary minerals, characterized primarily by dawsonite, in response to the aquatic milieu typifying the profound salinity stratum of terrestrial sedimentation. This milieu is notably enriched with Na+ ions and NaHCO3. This phenomenon suggests that feldspar, under these specific conditions, assumes the mantle of a mineral amenable to carbon sequestration, thus enriching the reservoir for CO2 mineralization within the salinity stratum of terrestrial sedimentation.

Accurate forecast of tail water level (TWL) is of great importance for the safe and economic operation and management of hydropower stations. The predictive performance is significantly influenced by the backwater effect of downstream hydropower stations and tributaries, but the explicit quantification method of the backwater effect is lacked. In this study, a deep learning model based forecasting framework for TWL predictions is established and applied to forecast TWL of Xiangjiaba (XJB) hydropower stations, which is influenced by the backwater effect of downstream tributaries including Hengjiang River (HJR) and Minjiang River (MJR). Firstly, the lag time of the backwater effect of HJR and MJR is analyzed based on the permutation importance. The results demonstrate that the lag time of backwater effect on the TWL of XJB is 5-7 hours for the HJR and 1-2 hours for the MJR. Then, the runoff thresholds of the HJR and MJR for impacting the TWL of the XJB station are obtained by scenario comparison, and the results show that the thresholds of HJR and MJR are 700 m3/s and 7000 m3/s respectively. Finally, the deep learning methods based TWL forecasting model is established based on the lag time and threshold analysis. The model is used to forecast the TWL in future 48 hours. The results show that the forecasting model has a good predictive performance with 98.22% of absolute errors less than 20 cm. The mean absolute error over the validation dataset is 5.27 cm and the maximum absolute error is 63.35 cm.

A global existential and interlocking environmental, climate and cooperation/equity polycrisis is being faced, which increasingly impacts and is impacted by water and land systems. As a result, transformations in response are gaining increasing traction. Advances in approaches to visualising and communicating how innovations and changes in landscape features enable shifts, transformations and transitions are more crucial than ever before. Visions help focus actions, collaboration and alignment of multiple actors in working towards a common purpose, whilst also entering people’s consciousness at the deep level of values, transforming beliefs and consequently, thinking and action. They give direction on effort and pull on transformational innovation. The evidence-based ‘Water Visions Visualisation Platform’ presents an innovative and accessible way to illustrate, communicate and support future water visioning and strategizing at the landscape scale based on composite paradigms, scenarios, horizons and concepts. Plausible visions of the future are envisioned, illustrated, narratively described and qualitatively assessed, as well as connected with real-world examples and resources through the interactive Platform. This paper outlines the co-creation methodology, the architecture and the co-development of the Platform, as well as a preliminary evaluation through literature-based criteria and the sharing of the Platform with a number of audiences.

Carbon dots are carbon based nanoparticles, which have the characteristics of simple preparation process, photoluminescence, biocompatibility, adjustable surface function, water solubility, and low toxicity. They are widely used in biological applications such as imaging, biosensing, photocatalysis, and molecular transfer. It has also aroused great interest among researchers in agriculture and has made significant progress in improving crop growth and production. This review presents the physiological functions of carbon dots for crop growth and development, photosynthesis, water and nutrient absorption, and abiotic stress resistance and their applications in improving ecological environment and agriculture as biosensors, and the future application prospects and research directions of carbon dots in agriculture were prospected.

This paper presents a parametric study of the multistorey hydro-powered pump, known as "Bunyip," which has demonstrated significant potential in contributing to rural regions. The study aims to understand the underlying physics of the system and enhance its hydraulic performance. A transient three-dimensional model using the commercial Computational Fluid Dynamics (CFD) tool Ansys-Fluent is utilized to gain insights into the fundamental flow mechanics, operational efficiency, standard capacity, and relative delivery. The investigation involves an initial assessment of performance for three Bunyip devices based on manufacturing data. Parametric analysis is conducted, and a parametric dataset is generated through meticulous application and numerical modelling. The CFD results are validated against experimental data. Three design configurations are considered, and 58 sets of varied input parameters are examined. The best design configuration is evaluated against five cases of conventional hydro-power pump systems. The results indicate that a smaller diameter of the pressure chamber and a higher supply head lead to higher pressure, achieving a target head of 3 m with 15% efficiency and a flowrate of 11.82 l/min.

With the gradual improvement of coal mining efficiency, the disturbance of groundwater system caused by the high-intensity mining mode also increases, which is a more severe challenge to the prevention of mine safety and the protection of water resources in mining areas. How to accurately describe the dynamic changes of the groundwater system under mining and quantitatively predict mine water inflow is a major problem in the current research. Based on the full analysis of the response characteristics of groundwater system to the extraction disturbance, this paper forms a kind of method to establish a mine hydrogeological conceptual model that can accurately represent the water inrush process, and uses the MODFLOW non-structural division grid to accurately characterize the formation structure, and finally make accurate water inflow prediction. Taking the Caojiatan Coal Mine in Shaanxi Province, China as an example, a numerical model of unstructured mine water inrush was established for the first time, and the changes of water inflow source and water inflow intensity were quantitatively evaluated. Compared with the traditional water inflow prediction method, it is found that the prediction accuracy is improved by 12%~17% by detailing the response characteristics of complex groundwater system under high-strength coal seam mining conditions. The method is of great significance and promotion value for the comprehensive understanding of the disturbance characteristics of human underground engineering activities, such as coal mining, on the groundwater system, and for accurately predicting water inflow.

Hydrogels can be considered as mimics of extracellular matrix (ECM).Cytoskeleton through integrins is connected with ECM and cytoskeleton tension depends on ECM stiffness.A number of age-related diseases depend on cellular processes related with cytoskeleton function.Some examples of cancer initiation and progression and heart disease in relationship with ECM stiffness has been analysed.Incorporation of rigid particles in ECM can increase ECM stifness and to promote formation of internal residual stresses. Water migration, changes of water binding energy to biomactomolecules, changes of the state of water from tightly bound water to free and loosely bound water changes stiffness of ECM. Risks related with rigid particles incorporation into ECM have been also iscussed.

During the development of horizontal wells in bottom water reservoirs, the strong heterogeneity of reservoir permeability leads to premature bottom water breakthrough at locations with high permeability in the horizontal wellbore, and the water content rises rapidly, which seriously affects production. In order to cope with this problem, a new technology has emerged in recent years that utilizes gravel filling to block the flow in the annulus between the horizontal well and the borehole, and utilizes the Inflow Control Device (ICD) completion tool to carry out segmental water control in horizontal wells. Unlike conventional horizontal well ICD completions that use packers for segmentation, gravel pack combined with ICD completions breaks the original seg-mentation routine and increases the complexity of production dynamic simulation. In this paper, the flow in different spatial dimensions such as reservoir, gravel packed layer, ICD completion section and horizontal wellbore is modeled separately, and the annular pressure at different locations is used as the solution variable for the coupled solution, which realizes the prediction of oil production, water production and water content of gravel pack combined with ICD completions of horizontal wells. The model was used to calculate the effects of different crude oil viscosities, different reservoir permeabilities, different permeabilities of gravel packed layers, and different development stages on the water control effects of gravel pack combined ICD completions and conventional ICD completions at field conditions. This study provides a basis for using gravel pack combined ICD completions in horizontal wells in bottom water reservoirs.

The cutting of difficult-to-machine materials, including their preconditioning, often requires specialised tools and machinery. An alternative processing technology can be cutting materials with a water jet. From the initial stage, the selection of appropriate technological parameters will influence what further finishing treatments will be applied. Vibrations occurring during this process can negatively affect the quality of the cutting edges and surfaces. Therefore, this study analysed vibrations during water-jet cutting with variable technological parameters (speed vfi and pressure pi). To measure the vibrations, a three-axis accelerometer from SEQUOIA was used in water-jet cutting of three materials: aluminum alloy, titanium alloy, and steel. Based on the study, it was found that the maximum value of vibration amplitude reaches the lowest value of vibration acceleration for aluminum alloy (not exceeding 5 m/s2), regardless of the value of pressure during the cutting process. This, taking into account the material properties, indicates that aluminum alloy is the material most susceptible to the cutting process while maintaining a high quality of the cutting surface. Significantly higher values of vibration acceleration amplitude (reaching up to 60 m/s2) during cutting were registered for steel and titanium alloy in all zones and phases of the process (entry zone, cutting zone, and exit zones).