The general circuit topology and principles of low-noise high-voltage power supply are investigated to meet the requirements of the high-voltage bias application in air kerma meters. Two topologies, flyback converter and Royer converter are simulated using SPICE simulation program. The simulation results indicate that the circuit structure of the Royer converter is more complex, but it obtains lower output high voltage noise. While we develop an adjustable high-voltage power supply according to the circuit structure of the Royer converter, and tested it to ensure the design requirements for continuously adjustable output high-voltage linearity. The test results show that the linear adjustment rate is not more than ±0.0025%, the load regulation rate is less than ±0.1%, and the output ripple noise voltage percentage is less than 0.01%. These tested performance make it more suitable for accurate nuclear measurements.

Fringe projection profilometry(FPP) has been extensively applied in various fields for its superior fast speed, high accuracy and high data density. However, measuring some objects with high reflective surfaces or high dynamic range surfaces remains challenging for FPP. Some multiple exposure image fusion methods have been proposed and successfully improved the measurement performance for these kinds of objects. Normally, these methods have a relatively fixed sequence of exposure settings determined by artificial experience or trial and error experiments, which may decrease the efficiency of the entire measurement process and may have less robustness to various environmental lighting conditions and object reflective properties. In this paper, a novel self-adaptive multiple exposure image fusion method is proposed with two main aspects of improvement on adaptively optimizing the initial exposure and the exposure sequence. By introducing the theory of information entropy, combined with the analysis of the characterization of fringe image entropy, an adaptive initial exposure searching method is first proposed. Then, an exposure sequence generation method based on dichotomy is further described. On the base of these two improvements, a novel self-adaptive multiple exposure image fusion method for FPP as well as its detailed procedures are given. Experimental results validate the performance of the proposed self-adaptivity multiple exposure image fusion method by measuring the objects with different surface reflectivity and in different ambient lighting conditions.

Introduction: The combination of Virtual Screening (VS) techniques with in vivo screening in the zebrafish model is currently being used in tandem for drug development in a faster and more efficient way. Areas covered: We review the different virtual screening techniques, the use of zebrafish as a vertebrate model for drug discovery and the synergy that exists between them. Expert opinion: We highlight the advantages of combining virtual and zebrafish larvae screening for drug discovery. On the one hand, VS is a faster and cheaper tool for searching active compounds and possible candidates for therapy than in vivo screening when processing large compound libraries. On the other hand, zebrafish larvae form a vertebrate model which allows in vivo screening of large amounts of the compounds. Importantly physiology and chemical response are mostly conserved between zebrafish and mammals. The availability of the transgenic and mutant zebrafish lines allows an analysis of a specific phenotype upon treatment along with toxicity, off-target effect, side effects, and dosage. Advantages of VS, in vivo whole animal approach screening, and the screening combinations are also reviewed.

A low-cost medium power carbon dioxide (CO₂) laser system is designed, constructed, and characterized to produce coherent, monochromatic laser radiation in the Infrared region. The laser cavity is simulated and designed by using ZEMAX optic studio. A switch-mode high tension pump source is designed and constructed using a flyback transformer and simulated using NI Multisim to study the voltage behavior at different node points. A prototype cooling system/chiller is designed and built using the Thermo-Electric Coolers (TEC) to remove the excess heat produced during laser action. Various parameters, like pumping mechanism, chiller stability, efficiency, output power, and current at different applied voltages, are studied. The chiller efficiency at different output powers of the laser is analyzed, which clearly shows that the chiller's cooling rate is good enough to compensate for the heat generated by the laser system. The center wavelength of the carbon dioxide laser is 10.6μm with FWHM of 1.2nm simulated in the ZEMAX optic studio. The output beam penetration through salt rock (NaCl), wood, and acrylic sheet at various output powers is analyzed to measure the penetration depth rate of the CO₂ laser.

As one of the most promising ablative fillers, multi-walled carbon nanotubes (MWCNTs) have been used to improve the ablative resistance of Ethylene-Propylene-Diene Monomer (EPDM) insulators by facilitating the carbothermal reduction reaction of silica. However, the contribution of MWCNTs to char layer structure of the insulators was unclear. In this work, the effects of MWCNTs on char layer structure and ablative resistance were investigated in different EPDM-based insulators with and without silica. The results showed that adding only 3 phr MWCNTs can reduce the linear ablation rate of EPDM-based insulators without silica by 31.7%, while 6 phr MWCNTs are required to obtain similar results in EPDM-based insulators with silica. Both the char layer morphology of the two insulators gradually evolved into dense porous structure as MWCNTs content increasing, but their formation mechanisms are different. The XRD and Raman spectrum showed that different physicochemical reactions occurred around MWCNTs under different charring components. The proposed ablation mechanism was further verified by designing alternating multilayer distribution of MWCNTs and silica. This work can guide the construction of desirable char layer structure for increasing ablative resistance of EPDM-based insulators.

The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC crystal structure was additively manufactured with a selective laser melting (SLM) process starting from mechanically alloyed powders. The as produced alloy shows finenitride and  phase pre-cipitates, which are Cr-rich and stable up to about 900 K. The precipitates increase in number and dimensions after long-period annealing at 900-1300 K, with a change in the HEA mechanical properties. Higher aging temperatures in furnace, above 1300 K, turn the alloy in a single FCC structure, with disappearance of the nitrate and  phase precipitates inside the grains and at the grain boundaries, but with still a presence of a finer Cr-rich nitride precipitation phase. These re-sults suggest that the as-produced HEA is a supersatured solid solution at low and intermediate temperature with nitrides and  nanostructures.

Few studies have examined the role of mediating mechanisms played by bricolage in the relationship between strategic flexibility and new product development, even though most of the studies view strategic flexibility as a capability to cope with environmental turbulence and promote product innovation. The bricolage approach embraces the resource-based understanding of the product development process as a concrete process of recombining resources in the process and exploring the mechanisms behind the bricolage approach. This study is the first of the kind that has examined the empirical effect of environmental turbulence on new product development through serial mediation of strategic flexibility and bricolage. Based on our results, environmental turbulence positively and significantly affects new product development through the serial mediation of strategic flexibility and bricolage. Bricolage is one of the mechanisms by which strategic flexibility may play a part in supporting product innovation. Our contribution to strategic flexibility research comes from examining the effect of strategic flexibility on bricolage and new product development from the point that environmental turbulence compels the high-tech industries to remain strategically flexible for their sustainability and growth. Besides providing new evidence on the relationship between environmental turbulence and product innovation, this research also provides new insight into the economic opportunity of new product development in transition economies such as China.

Turbulence is a fluid dynamic problem refractory to mathematical treatment. Examining a theoretical model of liquid water flowing in a cylinder at different Raleigh numbers, we propose a novel approach to elucidate the first stages of turbulent flows. The weakly bonded molecular assemblies of liquid water form a fluctuating branched polymer in which every micro-cluster displays different density. Against the common view of liquid water as an incompressible and continuous fluid, we suggest that the occurrence of transient local aggregates could be able to generate the vortices and eddies that are the hallmarks of turbulence. We quantify the local changes in velocity, diameter and density required to engender “obstacles” to the average flow. Then, we show how these microstructures, equipped with different Raleigh numbers and characterized by high percolation index, could generate boundary layers that contribute to micro-vortices production. We conclude that the genesis of turbulence cannot be assessed in terms of collective phenomena, rather is sustained, among many other factors, by the underrated microscopic inhomogeneities of fluids like liquid water.

The electronic structural evolution of LLM-105 crystal and the (101) plane of LLM-105 crystal under different pressures is investigated by the density functional theory (DFT) calculations and the surface properties of seven low-Miller-index planes of LLM-105 crystal were investigated in this study. The result demonstrates that the surface energy of (101) plane of LLM-105 is much smaller when compared with other low-Miller-index planes of LLM-105.In order to further investigate the stability of crystal structure and (101) plane of LLM-105 under different pressures, a series of pressures ranged from 0 GPa to 55 GPa were applied during the DFT calculation, and the result shows that the electronic structures of LLM-105 crystal and the (101) plane changed with the increase of external pressure and the evolution process of (101) plane is different from that of LLM-105 crystal structure.

A summer high school baseball tournament is held every mid-summer in Koshien Stadium. “Koshien Baseball” is very popular in Japan; however, it faces the problem of extremely high temperatures during games. Thus, high school players are threatened by the harsh environment. For this reason, Internet surveys were conducted twice to purposefully engage the same individuals. Then, information on their views regarding the Koshien tournament before and after the provision of information regarding environmental change in Japan was gathered. Using data, this study examined how their views changed after having the information. Compared with the view before, it was found that (1) respondents were more likely to agree that the management rule of the Koshien tournaments should be altered to protect player’s health, and (2) the impact of providing information is larger for female respondents, young people, and highly educated respondents.

To reduce the carbon emissions during heating in the manufacturing process, microwaves have attracted significant attention. Microwave has a lot of advantages rather than traditional heating method such as rapid heating, lower thermal damage and eco-friendly process. In order to apply microwaves to manufacturing process, uniform and efficient heating is required. We have analyzed the effect of various design parameters such as cavity heights, the application of the reflector, and the number and positions of waveguides for uniform and efficient heating by numerical simulation and verified that by experiment. The results showed that a slight change in the cavity height altered the electromagnetic field distribution and heating parameters, such as the coefficient of variance and power absorption efficiency. With reflectors installed, uniform heating was achieved and power absorption was improved, with the spherical reflector showing the maximum efficiency. The use of double waveguides heated the target material in a uniform manner. An increase in the power supply also led to uniform heating. This large-scale analysis will be helpful in applying microwaves to actual industrial sites.

By means of X-ray computed microtomography (XCMT) the existence of a developed microporous structure having an average pore diameter of ~3.5 μm and pore content of ~1.1 vol.% has been revealed in unirradiated polytetrafluoroethylene (PTFE). It has been found that the combined action of gamma radiation (absorbed dose per PTFE of ~170 kGy) and high temperatures (327-350 °C) leads to the disappearance of the microporous structure and the formation of several large pores with sizes from 30 to 50 μm in the bulk of thermal-radiation modified PTFE (TRM-PTFE). It has been established by X-ray diffraction (XRD) analysis that the thermal-radiation modification of PTFE leads to an increase in the interplanar spacings, the degree of crystallinity and volume of the unit cell, as well as to a decrease in the size of crystals and the X-ray density of the crystalline phase in comparison with the initial polymer. It is assumed that the previously established effect of improving the deformation-strength and tribological properties of the TRM-PTFE can be due not only to the radiation cross-linking of polymer chains but also to the disappearance of the micropore system and to the ordering of the crystalline phase of PTFE.

Cyanobacteria are microorganisms able to adapt to a wide variety of environmental conditions and abiotic stresses. They produce a very large number of metabolites that can participate in the adaptation of cyanobacteria to a large range of resources such as light, temperature, or nutrient. The metabolites variation is one way to understand the physiological status and adaptation of cells. In this study, we aim to understand how the diversity and the dynamics of the whole metabolome is dependent of the growth phases and under control of abiotic factors (e.g. light intensity and temperature). The cyanobacteria Aliinostoc sp. PMC 882.14 was selected for its large number of biosynthetic gene clusters. Metabolomes were analyzed by using mass spectrometry (qTOF-MS/MS) combined with untargeted analysis to investigate the metabolite dynamics. Significant variations were characterized between exponential and stationary phases, whatever the culture conditions (“control”, “higher light”, or “higher temperature”). ”Higher light” and “higher temperature” favored the synthesis of metabolites belonging to the same molecular families. Among highly regulated metabolites, we observe the presence of mycosporine-like amino acids (MAAs), and various variants of somamides, microginins, and microviridins. Through Aliinostoc sp. PMC 882.14, this study shows the importance of knowing the physiological state of cyanobacteria for comparative global metabolomics and questions the regulation processes involve into metabolite families production. Our results also open up new perspectives in the context of the production of targeted bioactive metabolites.

This letter aims to show the connection between the sinc approximation for high-energy absorption cross section and the shadow radius of the spherically symmetric black hole. This connection can give a physical interpretation of the absorption cross section in the eikonal limit parameters. Moreover, the use of this alternative way, one can extract its shadow radius from the absorption cross section in high energy limits to gain more information about the black hole spacetime. Our results indicate that the increasing the value of the shadow radius of the black hole, exponentially increase the the absorption cross section of the black hole in high-energy limits which can be captured by the Event Horizon Telescope (EHT) collaboration.

Magnetic sensors are widely used in health management systems for turbomachinery, but their applications in the hot zone are limited due to the loss of magnetic properties by permanent magnets with increasing temperature. The paper presents and verifies models and design solutions aimed at improving the performance of an inductive sensor for measuring the motion of rotating objects operating at elevated temperatures (200-1000C), such as compressor and turbine blades. Physical, analog and mathematical models of the interaction of blades with the sensor were developed. A prototype of the sensor was made and its tests were carried out on the RK-4 rotor rig for the speed of 7000 rpm, in which the temperature of the sensor head was gradually increased to 1100C. The sensor signal level was compared to that of an identical sensor operating at room temperature. The heated sensor works continuously producing the output signal whose level does not change significantly. What is more, a set of six probes passed an initial engine test in an SO-3 turbojet. It was confirmed that the proposed design of the inductive sensor is suitable for blade health monitoring of the last stages of compressors, steam turbines as well as previous generation gas turbines operating below 1000C, even without a dedicated cooling system. In real-engine applications, sensor performance will depend on how the sensor is installed and the available heat dissipation capability

In this paper we provide a highly selected review and synthesis on some of the recent and notable contribution to research in portfolio analysis. A unique perspective on this development in the literature is offered in this paper by judiciously identifying a few sample eigenvalues adjustment patterns in a portfolio that leads to an improvement in the out-of-sample portfolio Sharpe ratio when the population covariance matrix admits a high-dimensional factor model. These patterns unveil a key insight into a portfolio performance improvement and shed an important light on the effectiveness of a few recently introduced ”robust to estimation errors” covariance matrix estimation approaches, which were not originally designed with the goal to improve the out-of-sample portfolio performance.

The use of vitamin D (VitD) supplements has become widespread in the last decade due not only to the dissociation between the blood levels recommended as "optimal" and those shown by the healthy population, but also to its presumed beneficial effects on multiple disorders. This work evaluated the levels of 25-hydroxyvitamin D [25(OH)D] in a healthy population of European origin living in a region with high solar irradiation. In serum samples from a population-based study conducted in the Canary Islands, levels of 25(OH)D were analyzed. In 876 individuals who had no history of kidney or malabsorption disorders and who had not been treated with calcium and/or VitD supplementation, the median 25(OH)D level was 26.3 (5th;95th percentile, 14.3;45.8)ng/mL. Notably, 65.4% of the population had 25(OH)D blood levels below 30ng/mL, 23.4% below 20ng/mL and 6.4% below 15ng/mL. Based on the lack of evidence supporting causality between 25(OH)D levels below what is recommended as optimal (≥20ng/mL, or even ≥30ng/mL) and major skeletal and non-skeletal diseases, and in light of the distribution of the concentration of this vitamin in healthy adults living under optimal conditions of solar irradiation, it seems reasonable to consider 25(OH)D levels below 20ng/mL and close to 15ng/mL as adequate for the general population.

In this study, we report a new epoxy acrylate based shape memory polymer(SMP) fabricated by Liquid crystal display (LCD) Stereolithographic 3D printing. The printed 3D object has a high resolution and high transparency in visible light region. The uniaxial tensile tests showed enhanced tensile toughness and tunable mechanical properties. The fix-recovery and cycle tests indicated high shape recovery properties including high shape recovery rate and excellent cycling stability. In addition, a smart electrical valve actuator was fabricated that can be used in fast heat or electricity responsive electrical circuits. LCD 3D printing provides a low-cost and high efficient way to fabricate fast responsive SMP, which can be used in wide applications in various fields on aerospace engineering, biomedical devices, soft robots and electronic devices.

The interest in high homogenization pressure technology has grown over the years. It is a green technology with low energy consumption, not generating high CO2 emissions or polluting effluents. The main food applications derive from its effect on particle size, causing a more homogeneous distribution of fluid elements (particles, globules, droplets, aggregates, etc.) and favouring the release of intracellular components; and its effect on the structure and configuration of chemical components such as polyphenols and macromolecules such as carbohydrates (fibres) and proteins (also microorganisms and enzymes). The challenges of the 21st century lead food industry processing towards obtaining food with high nutritional quality and taking advantage of waste to obtain ingredients with specific properties. For this purpose, soft and non-thermal technologies such as high pressures homogenization have a huge potential. The objective of this work is to review how the need to combine safety, functionality and sustainability in food industry has conditioned the last decade applications of high-pressure homogenization technology.

In the end of December 2019, a new strain of coronavirus was identified in the Wuhan city of Hubei province in China. Within a shorter period of time, an unprecedented outbreak of this strain was witnessed over the entire Wuhan city. This novel coronavirus strain was later officially renamed as COVID-19 (Coronavirus disease 2019) by the World Health Organization. The mode of transmission had been found to be human-to-human contact and hence resulted in a rapid surge across the globe where more than 1,100,000 people have been infected with COVID-19. In the current scenario, finding potent drug candidates for the treatment of COVID-19 has emerged as the most challenging task for clinicians and researchers worldwide. Identification of new drugs and vaccine development may take from a few months to years based on the clinical trial processes. To overcome the several limitations involved in identifying and bringing out potent drug candidates for treating COVID-19, in the present study attempts were made to screen the FDA approved drugs using High Throughput Virtual Screening (HTVS). The COVID-19 main protease (COVID-19 Mpro) was chosen as the drug target for which the FDA approved drugs were initially screened with HTVS. The drug candidates that exhibited favorable docking score, energy and emodel calculations were further taken for performing Induced Fit Docking (IFD) using Schrodinger’s GLIDE. From the flexible docking results, the following four FDA approved drugs Sincalide, Pentagastrin, Ritonavir and Phytonadione were identified. In particular, Sincalide and Pentagastrin can be considered potential key players for the treatment of COVID-19 disease.

High-Rise buildings with their particular features can affects on surrounding environment and makes new microclimates. In the windy conditions, the spaces that are between building blocks changes to passages and affects on the wind velocity, intensity and it’s other parameters.The importance of this effect is different in each level of building height. The Pedestrian-Level is the lowest and one of important areas. Markets, playgrounds and pedestrian access had located in this area and any unwanted microclimate changes like high velocity and turbulence in this level can makes discomfort and dangerous condition for residents. So this research tries to consider the pedestrian- level wind comfort in some High-Rise building complexes arrangement that had located in Tehran district 22 with Computational Fluid Dynamics (CFD) modeling and reaching to a suitable arrangement pattern. It had collected the required data through field study and librarian databases and then compared them with standard guidelines and analyzed them by comparative comparison method. As a result a linear arrangement that placed crossover to wind direction for providing wind comfort and preventing wind danger is been suggested in this region.

A new frontier in solar thermal panel technology can be a high vacuum collector, thick enough to be equipped with solar concentrators based on non-imaging optics, such as the Compound Parabolic Concentrators (CPC). The high vacuum technology guarantees higher operating temperatures thanks to the enhanced thermal insulation, which leads to pay particular attention to the absorber radiative emission. In this paper by means of numerical simulations we compare the efficiency of a flat selective solar absorber under high vacuum to the efficiency of a CPC under high-vacuum collector.

Magnetic iron oxide particles are used for in vitro diagnostics for nearly 40 years. Due to their unique physical, chemical, thermal and mechanical properties, as well as biocompatibility and low toxicity in the human body, iron oxide nanoparticles have been used in many biomedical applications, such as contrast agents for magnetic resonance imaging, carriers for controlled drug delivery and immunoassays, but also in magnetic hyperthermia. Our aim is to investigate the effect of pressure and temperature on the structural, thermal and magnetic properties of iron oxide nanomaterials prepared by hydrothermal synthesis. Iron oxide nanoparticles were synthesized at temperatures of 100-200°C and pressures of 20-1000 bar. It has been found that pressure influences the type of iron oxide crystalline phase. Thus, for lower pressure values (< 100 bar), iron oxide is predominantly formed as hematite, while at pressures > 100 bar, the major crystalline phase is goethite. The complex thermal analysis revealed the polymorphic changes of iron oxides at different temperatures. The existence of specific magnetite and hematite phases in all thermally treated samples are evidenced through the specific Verwey and Morin transitions highlighted by ZFC-FC (Zero Field Cooled-Field Cooled) measurements, whereas their relative content is precisely provided by Mössbauer spectroscopy.

By using hydrogen quench continuous annealing technology, Stelco Inc. has developed a suite of Advanced High Strength Steel (AHSS) grades with tensile strength greater than 1000MPa to meet standard automotive specifications and for unique customer requirements. These grades were optimized by correlating chemical composition and processing parameters with microstructures and mechanical properties. Dual-Phase 980 (Stelco trademarked STELMAXTM 980DP), Multi-Phase 1180 (STELMAXTM 1180MP), Martensitic Steel 1300 (STELMAXTM 1300M) and 1500 (STELMAXTM 1500M) products met strength and formability requirements with excellent flatness and surface quality. Hydrogen quench continuous annealing technology not only ensures all developed AHSS grades have consistent mechanical properties across the entire strip length (from strip head to tail) and width (from edge to edge), but also produces high product yield compared with other continuous annealing processes.

Root research on field grown crops is hindered by the difficulty of estimating root biomass in soil. Root washing, the current standard method is laborious and expensive. Biochemical methods to quantify root biomass in soil, targeting species-specific DNA, have potential as a more efficient assay. We combined an efficient DNA extraction method, designed specifically to extract DNA from soil, with well-established quantitative PCR methods to estimate the root biomass of twenty-two wheat varieties grown in field trials over two seasons. We also developed an assay for estimating root biomass for black-grass, a common weed of wheat cultivation. Two robust qPCR assays were developed to estimate the quantity of plant root DNA in soil samples, one specific to wheat and barley, and a second specific to black-grass. The DNA qPCR method was comparable, with high correlations, with the results of root washing from soil cores taken from winter wheat field trials. The DNA qPCR assay showed both variety and depth as significant factors in the distribution of root biomass in replicated field trials. The results suggest that these DNA qPCR assays are a useful, high throughput tool for investigating the genetic basis of wheat root biomass distribution in field grown crops, and the impact of black-grass root systems on crop production.

Nitride and carbide are the second phases which play an important role in the performance of bearing steel, and their precipitation behavior is complicated. In this study, TiN-MC_x precipitations in GCr15 bearing steels were obtained by non-aqueous electrolysis, and their precipitation mechanisms were studied. TiN is the effective heterogeneous nucleation site for Fe₇C₃ and Fe₃C, therefore, MC_x can precipitate on the surface of TiN easily, its chemistry component consists of M₃C and M₇C₃ (M = Fe, Cr, Mn) and Cr₃C₂. TiN-MC_x with high TiN volume fraction, TiN forms in early stage of solidification, and MC_x precipitates on TiN surface after TiN engulfed by the solidification advancing front. TiN-MC_x with low TiN volume fraction, TiN and MC_x form in late stage of solidification, TiN can not grow sufficiently and is covered by a large number of precipitated MC_x particles.

The detection of temporary color steel buildings and the analysis of their spatiotemporal patterns and characteristics are of great importance in many developing cities, because areas densely distributed with color steel buildings are usually problematic regions with high population density, sustainable development and risk level, which are challenging for local governments. Using the high-resolution satellite images of the Anning District, Lanzhou City, China as the case study, this paper first extracts the information of the color steel buildings for two different periods. Then the spatiotemporal distributional characteristics of the color steel buildings are analyzed, both at small scale (temporary buildings) and large scale (planthouses, warehouses, etc.). Finally, this paper utilizes kernel density estimation, Delaunay triangulation and Voronoi diagrams to examine the spatial distribution, aggregation and proximity characteristics of the color steel buildings. Our experiments show that the temporal and spatial differences of urban development, the phased characteristics and urban space are represented by various types of color steel buildings. Thus, there are some robust coupling relationship between color steel buildings, urban spatial form and urban development.

By combing continuum topology optimization (TO) method and lattice structure technique, a sandwich aircraft spoiler with a high stiffness-to-weight is designed. TO method is served to produce the shell of the aircraft spoiler and the lattice structure, used as cores, is employed to support the shell. TO problem is established as maximizing the stiffness of the structure with limited material volume. Density-based method is utilized to achieve a 0/1 solution. We then empirically replace the core of the aircraft spoiler by using 3D kagome lattice structure. Two different materials, i.e., aluminum alloy and titanium alloy, are synthetically applied to further reduce the weight and simultaneously improve the strength of the aircraft spoiler. Numerical simulations are conducted to show that the designed aircraft spoiler can meet the service environment with a reduction of its weight by approximately 80% when compared with that of the initial design model. Finally, we have fabricated the designed model with photosensitive resin by using 3D printing technique.

The Pierre Auger Observatory is the world's largest operating detection system for the observation of ultra high energy cosmic rays (UHECRs). The detector allows detailed measurements of their energy spectrum, mass composition and arrival directions of primary cosmic rays in the energy range above $10^{17}$ eV. The data collected at the Observatory over the last decade show the suppression of the cosmic ray flux at energies above $4\times10^{19}$ eV. However, it is still unclear if this suppression is caused by the propagation of cosmic rays or rather by energy limitation of their sources. The other puzzle is the origin of UHECRs. Some clues can be drawn from studying the distribution of their arrival directions. The recently observed dipole anisotropy has an orientation which indicates an extragalactic origin of UHECRs. The Auger surface detector array is also sensitive to showers due to ultra high energy neutrinos of all flavours and photons, and recent neutrino and photon limits provided by the Observatory can constrain models of the cosmogenic neutrino production and exotic scenarios of the UHECRs origin, such as the decays of super heavy particles. In this paper the recent results on measurements of the energy spectrum, mass composition and arrival directions of cosmic rays, and future prospects are presented.

Factors affecting the host-virus interaction must be understood for the effective application of bacteriophages to combat bacterial pathogens. Two novel E. coli phages, the T1-like siphophage LL5 and the rV5-like myophage LL12, were subjected to forward genetic screens against the Keio collection, a library of single non-essential gene deletions in E.coli str. BW25113. These genome-wide screens and subsequent experiments identified eight genes required for efficient propagation of phage LL5 and six genes required for propagation of LL12. The majority of the genes identified were involved in production of the phage receptors. E. coli mutants deficient in heptose II and the phosphoryl substituent of heptose I of the inner core lipopolysaccharide (LPS) were unable to propagate phage LL5, as were mutants deficient in the outer membrane protein TolC. Mutants lacking glucose I of the LPS outer core failed to propagate LL12. Two cytoplasmic chaperones, PpiB and SecB, were found to be required for efficient propagation of phage LL5 but not LL12. This approach may be useful for identifying phage receptors and required host factors in other phages, which would provide valuable information for their potential use as therapeutics and for phage engineering.

The present study examined and compared the effects of high- and low-molecular weight (MW) chitosan, a nutraceutical, on intestinal and liver lipid metabolism in rats fed with high-fat diet. Both high- and low-MW chitosan decreased liver weight, elongated small intestine, improved the dysregulation of blood lipids and liver fat accumulation, and increased fecal lipid excretion in high-fat diet-fed rats. Supplementation of both high- and low-MW chitosan significantly inhibited the decreased phosphorylated AMP-activated protein kinase (AMPK)α and peroxisome proliferator-activated receptor (PPAR)α protein expressions and the increased lipogenesis/cholesterogenesis-associated protein expressions (sterol regulatory element binding protein (SREBP)1c, SREBP2, and PPARγ) and the decreased apolipoprotein (Apo)E and microsomal triglyceride transfer protein (MTTP) protein expressions in the livers of high-fat diet-fed rats. Both high and low-MW chitosan supplementation could also suppress the increased MTTP protein expression and the decreased angiopoietin-like protein (Angptl)4 protein expression in the intestines of high-fat diet-fed rats. Comparison between high and low-MW chitosan, high-MW chitosan has a higher efficiency than low-MW chitosan on the inhibition of intestinal lipid absorption and the increase of hepatic fatty acid oxidation, which can improve liver lipid biosynthesis and accumulation.

This review discusses a broad range of recent advances (2013-2017) of chemical imaging using electrochemical methods, with a particular focus on techniques that have been applied to study cellular processes, or techniques that show promise for use in this field in the future. Non-scanning techniques such as microelectrode arrays (MEAs) offer high time-resolution (< 10 ms) imaging, however at reduced spatial resolution. In contrast, scanning electrochemical probe microscopies (SEPMs) offer higher spatial resolution (as low as a few nm per pixel) imaging, with images collected typically over many minutes. Recent significant research efforts to improve the spatial resolution of SEPMs using nanoscale probes, and to improve the temporal resolution using fast scanning have resulted in movie (multiple frame) imaging with frame rates as low as a few seconds per image. Many SEPM techniques lack chemical specificity or have poor selectivity (defined by the choice of applied potential for redox-active species). This can be improved using multifunctional probes, ion-selective electrodes and tip-integrated biosensors, although additional effort may be required to preserve sensor performance after miniaturization of these probes. We discuss advances to the field of electrochemical imaging, and technological developments which are anticipated to extend the range of processes that can be studied. This includes imaging cellular processes with increased sensor selectivity and at much improved spatiotemporal resolution than has been previously customary.

Face routing has been adopted in wireless sensor networks (WSNs) where topological changes occur frequently or maintaining full network information is difficult. For message forwarding in networks, a planar graph is used to prevent looping, and because long edges are removed by planarization and the resulting planar graph is composed of short edges, messages are forwarded along multiple nodes connected by them even though they can be forwarded directly. To solve this, face routing using information on all nodes within 2-hop range was adopted to forward messages directly to the farthest node within radio range. However, as the density of the nodes increases, network performance plunges because message transfer nodes receive and process increased node information. To deal with this problem, we propose a new face routing using the planar graphs of neighboring nodes to improve transfer efficiency. It forwards a message directly to the farthest neighbor and reduces loads and processing time by distributing network graph construction and planarization to the neighbors. It also decreases the amount of location information to be transmitted by sending information on the planar graph nodes rather than on all neighboring nodes. Simulation results show that it significantly improves transfer efficiency.

The objective of this study is to evaluate the effect of constitutive equations on the prediction accuracy for springback in cold stamping with various deformation modes. In this study, two types of yield functions—Hill’48 and Yld2000-2d—were considered to describe yield behavior. Isotropic and kinematic hardening models based on the Yoshida–Uemori model were also adopted to describe hardening behavior. Various material tests (such as uniaxial tension, tension- compression, loading-unloading, and hydraulic bulging tests) were carried out to determine the material parameters of the models. The obtained parameters were implemented in the finite element (FE) simulation to predict springback, and the results were compared with experimental data. U-bending and T-shape drawing were employed to evaluate the springback prediction accuracy. Obviously, the springback prediction accuracy was greatly influenced by constitutive equations. Therefore, it is important to choose appropriate constitutive equations for accurate description of material behaviors in FE simulation.

A high step-up DC-to-DC converter that integrates an isolated transformer and a switched-clamp capacitor is presented in this study. The voltage stress of the main power switch should be clamped to 1/4 V by using the turn ratio and switched-clamp capacitor of an isolated transformer to achieve a high voltage gain. In addition, a passive clamp circuit is employed reduce voltage stress on the main power switch. The energy of the leakage inductor can be recycled by the clamp capacitor because of the passive clamp circuit, thereby improving the power converter efficiency. The converter consists of one isolated transformer, one main switch, three capacitors, and four diodes. Operating principle and steady-state analyses are also discussed. Finally, a 24-V-input voltage to 200-V-output voltage and a 150 W output power prototype converter are fabricated in the laboratory. The maximum efficiency of the converter is 95.1 at 60 W.

The challenge of missing data in scientific research prompts researchers to decide between imputing incomplete data or discarding observations, where discarding can lead to information loss. Various methods exist, from simple deletion to sophisticated approaches like Multiple Imputation (MI). However, these methods often fall short with high-dimensional datasets. Multiple Imputation by Chained Equations (MICE) and Random Forest (RF) proximity imputation offer promising alternatives. Therefore, in this paper, we propose integrating MICE with Bayesian random forest (BRF) to enhance imputation accuracy and predictive power, particularly in high-dimensional analyses. Our approach combines MICE’s efficiency with BRF’s robustness, offering a comprehensive solution to missing data challenges. By way of example, we provide empirical evaluations to validate its effectiveness using synthetic data of various missing data scenarios. The results from the simulations showed that the combination of BRF and MICE offered a promising strategy for high-dimensional analysis in the presence of missing data.

The intelligent elderly care model places new demands on the skills of aging caregivers. The identification and development of forward-thinking, high-potential nursing talent is essential for advancing the intelligent elderly care sector. Multi-benchmarking selection and competitive analysis is used to evaluate and identify nursing personnel in the rehabilitation treatment center of a hospital in Hefei City. Using proxy evaluation and democratic evaluation model, three types of benchmarks such as single item benchmark, individual benchmark and group benchmark were identified and selected, and the professional nursing team was constructed based on the evaluation results. Different from the traditional other-directed evaluation, multi-benchmarking selection and competitive analysis is self-directed evaluation, this method is more conducive to the identification of high-potential and digital nursing talents by intelligent elderly service organizations, and facilitates the formation of professional nursing teams with complementary strengths and cross-fertilization, so as to satisfy the diversified and multi-level needs of the elderly for intelligent elderly services.

CO2 geological sequestration in coal seams can achieve the dual objectives of CO2 emission reduction and enhanced coalbed methane production, making it a highly promising carbon capture and storage technology. However, the injection of CO2 into coal reservoirs in the form of supercritical fluid (ScCO2) leads to complex physicochemical reactions with the coal seam, altering the properties of the coal reservoir and impacting the effectiveness of CO2 sequestration and methane production enhancement.In this paper, theoretical calculations based on ReaxFF-MD were conducted to study the interaction mechanism between ScCO2 and the macromolecular structure of both low-rank and high-rank coal, to address the limitations of experimental methods. The reaction of ScCO2 with low-rank coal and high-rank coal exhibits significant differences. At swelling stage, the low-rank coal experiences a decrease in aromatic structure and aliphatic structure, high-rank coal shows an increase in aromatic structure and a decrease in aliphatic structure, while swelling phenomenon is more pronounced in high-rank coal. At dissolution stage, low-rank coal is initially decomposed into two secondary molecular fragments, and then recombine to form new molecular structure, the aromatic structure increased and the aliphatic structure decreased. In contrast, high-rank coal occurs stretches-breakage-movement-reconnection, a reduction in aromatic structure and an increase in aliphatic structure.The primary reasons for these variations lie in distinct molecular structure compositions and the properties of ScCO2, leading to different reaction pathways of functional group and aromatic structure. The reaction pathways of functional groups and aromatic structures in coal can be summarized as follows: the breakage of the O-H bond in hydroxyl groups, the breakage of the C-OH bond in carboxyl groups, transformation of aliphatic structures into smaller hydrocarbon compounds or formation of long-chain alkenes, and various pathways involving broken, rearrangement, recombination of aromatic structures. In low-rank coal, there is a higher abundance of oxygen-containing functional groups and aliphatic structures. The breakage of O-H and C-OH chemical bonds results in the formation of free radical ions, while some aliphatic structures detach to produce hydrocarbons. Additionally, some of these aliphatic structures combine with carbonyl groups and free radical ions to generate new aromatic structures. Conversely, in high-rank coal, the lower content of oxygen-containing functional groups and aliphatic structures, along with stronger intramolecular forces, results in fewer chemical bond breakages and makes it less conducive to the formation of new aromatic structures.These results elucidate the specific deformations of different chemical groups, offering a molecular-level understanding of the interaction between CO2 and coal.

Oral cancer represents a significant global public health challenge, contributing substantially to cancer incidence and mortality. Despite established risk factors such as tobacco use and alcohol consumption, early detection remains crucial for effective treatment. This study introduces a novel approach using a transistor-based biosensor system for detecting the P90 (CIP2A) protein. We have tested the presence of CIP2A in human leukoplakia samples that can rise into oral squamous cell carcinoma. The method employs commercially available glucose test strips functionalized with P90 antibodies, providing high sensitivity and a low limit of detection, which is five orders lower than commercial ELISA kits. A specially designed printed circuit board (PCB) facilitates accurate measurements, and the device's performance is optimized through characteristic tests. Human sample testing validates the biosensor's effectiveness in distinguishing samples after cell lysis. This study contributes to advancing accurate and cost-effective diagnostic approaches for oral pre-cancer and cancer tissues.

The objective of this study was to investigate the relationship between high-performance work systems and a company’s social performance, taking into account the organizational climate as a situational variable. Specifically, this study aimed to analyze the impact of perceptions of a high-performance work system on the perception of a company’s social responsibility (CSR) among employees of Jordanian companies with an organizational size of 300 or more. This study used 175 valid questionnaires, and SPSS and AMOS 24 were used to test the hypotheses. The results showed that there was a positive relationship between the perception of a high-performance work system and the perception of a company’s CSR. Furthermore, this study found that a positive diversity climate could enhance the positive relationship between the two. These findings suggest that high-performance work systems can contribute to the development of sustainable human resource management systems and that a positive diversity climate is essential in shaping these systems. Based on these results, it is recommended that companies implement HPWSs and encourage workforce diversity to maximize the value of CSR activities and ensure their sustainability.

Background: During the pandemic, Emergency departments were overcrowded with critically ill patients and confronted ethical dilemmas to assign respiratory support to them due to scarce resources. Quick tools to evaluate patients at admission were needed; many scores were used but inaccurate to predict outcomes. The Rox Index is an easy and fast score that reflects the respiratory status in acute respiratory failure patients, this score could predict the outcome of covid 19 patients. Hypothesis: The 24-hour difference in the Rox Index discriminate accurately the mortality and needs for mechanical ventilation of patients with covid-19. Methods: Study design: Prospective analytic study. Population: 204 Patients admitted to the emergency department from May to August 2020. Data were collected from the clinical records. The Rox Index was calculated at admission and 24h later, the difference was used to establish the outcome, a logistic regression model adjusting for age, sex, presence of comorbidities and disease severity to build and perform ROC analysis. Results: Difference in respiratory ROX Index between admission and 24h is a good predictor for death AUC 0.92 and for mechanic ventilation AUC: 0.75. Each decrease in one unit of the difference at 24h had an Odds Ratio for death risk: 1.48 (95%CI: 1.31-1.67) and for mechanic ventilation: 1.16 (95%IC: 1.1-1.23). Conclusion: The 24-hour variation of Rox Index has good predictive value and allows healthcare professionals to identify which patients will benefit from invasive treatment, especially in low resource settings where emergency physicians deal with survival.

Energy distance is used to eigenvalue distributions in this new Wishart distribution study, providing a new perspective on high-dimensional data. Multivariate statistics relies on Wishart distribution to explain covariance matrices. This analysis shows how degrees of freedom and covariance matrix configurations affect eigenvalue dispersion. We use energy distance based on eigenvalue distributions to assess Wishart distribution differences without the "curse of dimensionality" via extensive simulation simulations. This approach improves measurement accuracy and processing efficiency in distribution comparisons and enables new analytical pathways in scientific fields that need data covariance comprehension. Our results show that degrees of freedom and matrix structure considerably affect energy distances, expanding the theoretical framework and practical applications of statistical models.

The structural, elastic, and electronic properties of orthorhombic Cd2SiO4 and Hg2GeO4 were examined under varying pressure conditions using first-principles calculations based on densi-ty-functional theory employing the projector augmented wave method. The obtained cell pa-rameters at 0 GPa were found to align well with existing experimental data. We delved into the pressure-dependence of normalized lattice parameters and elastic constants. In Cd2SiO4, all lat-tice constants decreased as pressure increased, whereas in Hg2GeO4, parameters a and b de-creased while parameter c increased under pressure. Employing the Hill average method, we calculated the elastic moduli and Poisson’s ratio up to 10 GPa, noting an increase with pressure. Evaluation of ductility/brittleness under pressure indicated both compounds remained ductile throughout. We also estimated elastic anisotropy and Debye temperature under varying pres-sures. Cd2SiO4 and Hg2GeO4 were identified as indirect band gap insulators, with estimated band gaps of 3.34 eV and 2.09 eV, respectively. Interestingly, Cd2SiO4 exhibited a significant increase in band gap with increasing pressure, whereas the band gap of Hg2GeO4 decreased under pres-sure, revealing distinct structural and electronic responses despite their similar structures.

In the digital era, enhancing the heritage resources of a tourist route means describing and networking them to promote their visibility and attractiveness. Prior studies mainly assess mountainous region’s natural resources through multi-indicator descriptive evaluation. This study aims to develop a comprehensive measurement of indicator’s value while assessing the tourism development potential of mountainous rural area. It concerns the main tourist route of the UNESCO M'Goun Geopark, located in the central High Atlas of Morocco. It also involves analyzing the criteria for choosing this destination by segmenting tourists' consumption experiences. Statistical analysis of the collected data reveals five dimensions of destination choice and four visitor groups. This article proposes to discuss findings and their applicability in terms of tourism destination management and decision-making, which can help local governments to rationally allocate tourism resources and land use.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

Purposes: Engaging in regular physical activity has been consistently linked to improved physical health and academic performance. Despite its known benefits, there is a concerning trend of decreased physical activity among children globally. The study primarily aims to investigate the level of physical activity among junior high school students in Taiyuan and analyze the main affecting factors from a socio-ecological perspective. Methods: A cross-sectional study was conducted, involving 650 junior high school students from 7 schools in Taiyuan, and 648 valid questionnaires were collected. Physical activity levels were assessed using the Children’s Leisure Activities Study Survey Questionnaire. Factors influencing physical activity were evaluated through the Student Perceived Factors Affecting Physical Activity Questionnaire. Results: In this study, students from the 7th, 8th, and 9th grades participated in physical activities, averaging 214.5 minutes per week in moderate-intensity and 25 minutes in high-intensity activities, cumulatively averaging 280 minutes weekly. Notably, a significant disparity (p<0.05) was observed in the combined duration of moderate and high-intensity activities, with male students engaging more time compared to their female counterparts (307.500 vs 255.000 minutes). This variance extended across different grades, particularly evident in 8th graders who recorded the highest weekly high-intensity activity duration (31.000 minutes) and overall physical activity time (320.500 minutes), surpassing the 7th graders. Furthermore, an exploratory factor analysis of a 32-item questionnaire, designed to identify determinants of physical activity, revealed six principal components. These components were found to positively correlate with both moderate and high-intensity physical activities. Conclusion: This study emphasizes the necessity for educational institutions and community programmes to provide engaging physical activities, especially during weekends. It highlights the importance of tailoring physical education curricula to address gender and grade differences and investing in quality sports equipment and facilities by schools and local governments.

Experimental investigations were conducted to uncover the impact of cavitation control - through the use of riblets (mesoscale surface structuring) - on cavitating flows around a circular cylinder. First, the dynamics of cavitation in the flow behind a finite cylinder (without riblets) was unveiled by visualizing the cavitation clouds and measuring the lift force fluctuations acting on the cylinder. Second, as a significant step forward, a comprehensive explanation was provided for the mechanism of cavitation control using two bio-inspired riblet morphologies positioned in different orientations and locations on the cylinder. For the first time, the effects of these tiny structures on the flow dynamics and the associated cavitation process were scrutinized. This showed that scalloped riblets, with their curved design, induced secondary vortices near their tips and distorted primary streamwise vortices, and that high velocity gradients near the jagged pattern peaks of sawtooth riblets delayed flow separation, which affected cavitation.

Genetic engineering and directed evolution are effective methods to address the low yield and poor industrialization level of microbial target products. The current research focus is on how to efficiently and rapidly screen beneficial mutants from constructed large-scale mutation libraries. Traditional screening methods such as plate screening and well plate screening are severely limited in their development and application due to their low efficiency and high costs. In the past decade, microfluidic technology has become an important high-throughput screening technology due to its fast speed, low cost, high automation, and high screening throughput, and it has developed rapidly. Droplet-based microfluidic high-throughput screening has been widely used in various fields such as strain/enzyme activity screening, pathogen detection, single-cell analysis, drug discovery, and chemical synthesis, and has been widely applied in industries such as materials, food, chemicals, textiles, and biomedicine. In particular, in the field of enzyme research, droplet-based microfluidic high-throughput screening has shown excellent performance in discovering enzymes with new functions, improved catalytic efficiency or stability, acid-base tolerance, etc. Currently, droplet-based microfluidic high-throughput screening technology has achieved high-throughput screening of enzymes such as glycosidase, lipase, peroxidase, protease, amylase, oxidase, and transaminase, as well as high-throughput detection of products such as riboflavin, coumarin, 3-dehydroquinate, lactic acid, and ethanol. This article reviews the application of droplet-based microfluidics in high-throughput screening, with a focus on high-throughput screening strategies based on UV, visible, and fluorescence spectroscopy, including labeled optical signal detection screening, as well as label-free electrochemical detection, mass spectrometry, Raman spectroscopy, nuclear magnetic resonance, etc. Furthermore, the research progress and development trends of droplet-based microfluidic technology in enzyme modification and strain screening are also introduced.

Cavitation resulting from underwater explosions in compressible multiphase or multicomp-onent flows presents significant challenges due to the dynamic nature of shock-cavitation-structure interactions, as well as the complex and discontinuous nature of the involved interfaces. Achieving accurate resolution of interfaces between different phases or components, in the presence of shocks, cavitating regions, and structural interactions, is crucial for modeling such problems. Furthermore, pressure convergence in simulations involving shock-cavitation-structure interactions requires accurate algorithms. In this research paper, we employ the diffuse interface method, also known as the interface capturing scheme, to investigate cavitation in various underwater explosion test cases near different surfaces; free surface and a rigid surface. The simulations are conducted using the Unstructured Compressible Navier-Stokes (UCNS3D) finite volume framework employing central-weighted essentially non-oscillatory (CWENO) reconstruction schemes, utilising the five-equation diffuse interface family of methods. Quantitative comparisons are made between the performance of both models. Additionally, we examine the effects of cavitation as a secondary loading source on structures, and evaluate the ability of the CWENO schemes to accurately capture and resolve material interfaces between fluids with minimal numerical dissipation or smearing. The results are compared with existing high-order methods and experimental data, where possible, to demonstrate the robustness of the CWENO schemes in simulating cavitation bubble dynamics, as well as their limitations within the current implementation of interface capturing.

The superficial quality of the strip is a very important issue in steel production; the profile, flat-ness, and geometry of strip are indicators of supreme quality. Considering the dimensions, the thickness is one of the most important variables in the production of strip. In the present study the elastic curve of Back Up Rolls (BUR) is analyzed, considering them as simply supported beams as well as the effect of rolls on the profile of the strip, specifically in the strip edge pro-ducing edge drop. The analysis is simulated with a model in 3D using a Finite Element Method (FEM) considering +0.039mm crown on Back Up Roll and +0.101mm crown on Work Roll (WR). The results showed that there is an instability zone of 76mm in the strip edge, this geometry is symmetrical in both ends of the strip, it was validated with the results of compact X-ray thick-ness gauge from a 4-high cold mill. This study not only provides a theoretical basis for the edge drop, but also provides the basis for the understanding of deformation on rolls used in rolling mill processes and their effect on the thickness, profile, shape, and dimensional quality of strips.

Abstract: Objectives: To establish the expression profile of N6-methyladenosine(m6A) modifications in the hippocampus of mice with diabetic cognitive impairment (DCI) and elucidate the potential regulatory mechanism. Methods: A DCI model was established by feeding a high-fat diet to C57BL/6J mice. m6A and RNA sequencing was conducted to profile the m6A-tagged transcripts in the hippocampus. Results: Methylated RNA immunoprecipitation with next-generation sequencing and RNA sequencing analyses yielded differentially m6A-modified and expressed genes in the hippocampus of DCI mice, which were enriched in pathways involving synaptic transmission and axonal guidance. Mechanistic analyses revealed a remarkable change in m6A modification levels through alteration of the mRNA expression of m6A methyltransferases (METTL3 and METTL14) and demethylase (FTO) in the hippocampus of DCI mice. Conclusions: We identified a co-mediated specific RNA regulatory strategy that broadens the epigenetic regulatory mechanism of RNA-induced neurodegenerative disorders associated with metabolic and endocrine diseases.

In order to utilize high-alumina coal gangue (HACG) as auxiliary cementitious admixture, it is of fundamental significance to thermally activating Al2O3 effectively in HACG and promoting formation of hydratable products containing Al2O3. In this paper, a new preparation technology is developed to make HACG auxiliary cementitious admixture by thermal activation of HACG-Ca(OH)2 (CH) mixture. HACG powders mixed with 20wt.% CH were calcined within a temperature range of 600-900oC, the thermal transformation and mineral phase formation were analyzed by thermogavimetric analyzer (TGA), X-ray diffractometer (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDS). The hydration reaction between activated HACG-CH mixture and cement was also investigated. HACG experienced a conventional transformation from kaolinite to metakaolin at 600oC and finally to mullite at 900oC. However, CH underwent an unexpected transformation process from CH to CaO, then to CaCO3, and finally to CaO again with increasing calcining temperature. These substances states were associated with dehydroxylation of CH, chemical reaction between CaO and CO2 generating from combustion of carbon in HACG, and decomposition of CaCO3, respectively. It is the formation of a large amount of CaO above 800oC that favors the formation of hydratable products containing Al2O3 in the calcining process and C-A-H gel in hydration process. The mechanical properties of HACG-cement mortar specimens were measured, from which the optimal calcination temperature for preparing HACG auxiliary cementitious admixture was determined to be 850oC. As compared with pure cement mortar specimens, the maximum 28-d flexural and compressive strength of HACG-cement mortar specimens increased by 5.4% and 38.2%, respectively.

The effects of rare earth Y content on the microstructure and high-temperature oxidation properties of 47Fe-36Ni-15Cr-1.5Mn alloy at 1000°C were investigated. The results show that 47Fe-36Ni-15Cr-1.5Mn alloy oxidizes at 1000°C under laboratory atmospheric pressure to form an oxide film layer dominated by Cr2O3 and (Fe, Ni, Mn) Cr2O4 spinel, and the oxidation curve of the alloy follows the parabolic law. After the addition of rare earth Y, rare earth phases precipitated along the grain boundaries in the alloy, and the more Y content, the more precipitated phases in the grain boundaries. The alloy with added rare earths was oxidized at a high temperature of 1000 °C for 2160 min, the oxidation law still followed the parabolic law, while the rare earth phase at the grain boundary reacted with the oxygen atoms infiltrated from the outside to generate a rare earth Y-rich oxide residing at the boundary between the grain boundary and the precipitated phase of the alloy. Add 0.5 wt.% rare earth Y 47Fe-36Ni-15Cr-1.5Mn-0.5Y alloy 1000 ° C high temperature oxidation of the formation of spinel oxide crystalline particles, dense and complete oxide film layer, the surface of the addition of a small amount of (0.5 wt.%) rare earth Y after the refinement of the oxide particles, and in the alloy grain boundaries in the form of oxides reside in the alloy to inhibit the cations in the matrix and the oxygen negative ions. and oxygen-negative ions in the alloy matrix, improving the antioxidant performance of the alloy. With the further increase of rare earth Y, during the oxidation of the alloy at high temperature, the precipitation phase at the grain boundary promotes the inward diffusion of oxygen, resulting in the deterioration of the antioxidant property of the alloy.

The aeroelastic response of lightweight low-speed aircraft with slender wings under extreme flow turbulence intensity is not well-understood. Experiments on a commmercial unmanned aerial vehicle (UAV) with a 3-meter wingspan and aspect ratio of 13.6 were performed in a large open-return wind tunnel with extreme flow turbulence intensity of T∞≈10%. The structural dynamics of the wing in the bending mode and the flow beneath the wing to capture the effect of aileron deflection was measured using laser displacement sensors and tomographic particle image velocimetry (PIV) techniques. The unsteady lift produced by the wing was also measured using a high-capacity load cell at an angle of attack, α of 2 degrees for three freestream velocities U∞ of 13.4 m/s, 17.9 m/s, and 26.8 m/s representing the UAV’s stall through cruise speed. It was found that high flow turbulence intensity with large integral length scales relative to the wing chord plays a dominant role in the large unsteady lift and wing displacements measured. The power spectral density (PSD) of wing structural vibration shows that flow shedding from the wing and the integral length scales have a significant impact on the overall power inherent in the bending vibration of the wing. Computation of vorticity iso-surfaces in the flow measurement volume surrounding the aileron reveal a striking observation; aileron deflection, δa of 10∘becomes less effective in producing additional spanwise vorticity, which is proportional to circulation and lift, at U∞ of 26.8 m/s because the freestream already has elevated levels of vorticity. A paradigm shift in design is suggested for light aircraft structures with slender wings operating in highly turbulent flow, which is to employ multiple control surfaces in order to respond to this flow and mitigate large bending or torsion displacements and the probability of structural failure.

Bandsaw blades are typical band-shaped cutting tools characterized by a low stiffness and micro-level cutting depth, resulting in distinct wear mechanisms compared to rigid cutting tools. In this study, the evolution of bandsaw tooth wear mechanisms during the bandsawing of Cr12MoV cold-working steel was investigated. The tool life was divided into two stages according to the tooth wear mechanism: a rapid wear stage (Stage I) and a homogeneous wear stage (Stage II). In Stage I, the wear mechanism was dominated by chipping, although multiple wear mechanisms were found because of the relatively poor manufacturing tolerance compared to rigid cutting tools, resulting in remarkable differences between the cutting depths of the individual teeth. In Stage II, abrasive and adhesive wear were the primary wear mechanisms instead of chipping, due to the decreased width and setting magnitude tolerance after Stage I. Furthermore, methods for increasing the bandsaw performance were proposed based on the tooth wear mechanisms.

Obesity and overweight are associated with many metabolic diseases, such as hypertension, diabetes, and dyslipidemia, which are closely related to a sedentary lifestyle and lack of exercise. Aerobic exercise effectively increases the high-density lipoproteins-cholesterol (HDL-C) levels and decreases the triglyceride (TG) levels. The consumption of Cuban policosanol (Raydel®) is also effective in enhancing the HDL-C quantity and HDL functionality to treat dyslipidemia and hypertension. On the other hand, no study has examined the effects of a combination of high-intensity exercise and policosanol consumption in obese subjects to improve metabolic disorders. In the current study, 17 obese subjects (average BMI 30.0±1.1 kg/m2, eight male and nine female) were recruited to participate in a program combining exercise and policosanol (20 mg) consumption for 12 weeks. After completion, their BMI, waist circumference, total fat mass, systolic blood pressure (SBP), and diastolic blood pressure (DBP) decreased by approximately 15% (p=0.022), 12.7% (p=0.008), 33% (p=0.006), 11% (p<0.046), and 13% (p=0.007), respectively. In the serum lipid profile, at week 12, they showed a remarkable decrease in the total cholesterol (TC) and triglyceride (TG) levels, up to 17% (p<0.019) and 54% (p<0.002) from the baseline, respectively. Although the serum HDL-C was increased by approximately +12% from the baseline, the percentage of HDL-C in TC, HDL-C/TC (%), was increased by up to +32% (p=0.007) at week 12. The serum coenzyme Q10 (CoQ10) level was increased 1.2-fold in all participants at week 12 from the baseline. In particular, the male participants showed a 1.4-fold increase (p=0.027) from the baseline. The larger increase in serum CoQ10 was correlated with the larger increase in the serum HDL-C during 12 weeks. The hepatic function parameters were improved; the serum -glutamyl transferase decreased at week 12 by up to 55% (p<0.007), while the aspartate aminotransferase and alanine transaminase levels decreased within the normal range. In the lipoprotein level, the extent of oxidation and glycation were reduced significantly in VLDL and LDL, with a remarkable decrease in the TG content in particles. The antioxidant abilities of HDL2 and HDL3, such as paraoxonase (PON) and ferric ion reduction ability (FRA), were enhanced significantly by up to 1.8-fold (p<0.001) and 1.6-fold (p<0.001) at week 12. The particle size and number of HDL2 were increased up to +10% during the 12 weeks with a remarkable decrease in the TG content, glycation extent, oxidation up to 32% (p=0.032), 18% (p=0.043), and 11% (p=0.023), respectively. The particle number and diameter of HDL3 were increased by up to +9% with a remarkable increase in the PON activity, FRA activity, and TC content of +82% (p<0.001), +56% (p<0.001), and +32% (p=0.009), respectively. Expression of apolipoproteinA-I in HDL2 and HDL3 were significantly elevated more in both gender around 30~48% with more distinct band intensity and less glycation at week 12. These improvements in HDL quality and functionality were linked to the higher survivability of adult zebrafish and their embryos. Under the co-presence of carboxymethyllysine (CML), a microinjection of HDL2 to zebrafish embryo from week 0 resulted in approximately 47% survivability with developmental defects and attenuated speed. On the other hand, the HDL2 microinjection from week 12 resulted in remarkably higher survivability (~ 70%). In conclusion, 12 weeks of Cuban policosanol (Raydel®, 20 mg) consumption with high-intensity exercise showed significant improvement in blood pressure, body fat mass, blood lipid profile without liver damage, CoQ10 metabolism, and renal impairment. At week 12, all participants showed a remarkable decrease in oxidation and glycation extent in the VLDL and LDL with a decrease in the TC and TG content. Significant enhancement of the qualities and functionalities in HDL2 and HDL3 by the policosanol consumption were also detected: increase in apoA-I content, TC content, particle size, and particle numbers along with antioxidant abilities, such as PON and FRA.

Carbonization of a biopolymer (lignin) in self-propagating high-temperature synthesis (SHS) led to the production of 2D graphene structures. With the help of modern analytical methods (Raman spectroscopy, X-ray diffraction) and electron microscopy, the resulting product was confirmed to have a few-layer 2D graphene structure. The predicted photovoltaic properties of the resulting few-layer graphene were implemented for laser ignition of a model pyrotechnic composition based on porous silicon. A phenomenological model of the formation mechanism of 2D graphene structures under the conditions of the SHS process is proposed.

A twin-screw extruder was used to fabricate poly(butylene succinate) (PBS)/high density polyethylene (HDPE) blends (7:3 weight ratio) and blend-based nanocomposites. Carbon nanotubes (CNTs), graphene nanoplatelets (GNPs) and organoclays (15A and 30B) served as the nanofiller, while maleated HDPE (PEgMA) acted as an efficient compatibilizer for the blend. In the composites, individual nanofillers were mostly localized in HDPE domains, but some fillers were also observed at PBS-HDPE interfaces. The sea-island morphology of compatibilized blend evolved into a pseudo-co-continuous morphology in the composites. Differential scanning calorimetry results confirmed that PEgMA with HDPE evidently accelerated the crystallization of PBS in the blend. The possible nucleation effect of added fillers on PBS crystallization was obscured by the formation of quasi-connected HDPE domains, causing less PBS nucleation sites. The presence of nanofillers improved the thermal stability and burning anti-dripping behavior of the parent blend. The anti-dripping efficiency of added fillers followed the sequence: CNT>15A>30B>GNP. Rigidity of the blend was increased after formation of nanocomposites. In particular, adding GNP resulted in 31% increase in flexural modulus. Development of a pseudo-network structure in the composites was confirmed by measurement of rheological properties. Electrical resistivity of the blend was reduced by more than 6 orders of magnitude at 3 phr CNT loading, demonstrating the achievement of double percolation morphology.

Ornamental kale (Brassica oleracea var. acephala) is an attractive ornamental plant with a range of leaf colors and shapes. Breeding new varieties of ornamental kale has proven challenging due to its lengthy breeding cycle and the limited availability of genetic markers. Microspore culture is an effective approach to generate new materials and genetic maps are a prerequisite for quantitative trait loci analysis, MAS, fine gene mapping, and genome sequence assembly. In this study, a F1DH ornamental kale population comprising 300 DH lines was constructed using microspore culture. A high-density genetic map was developed by conducting whole-genome sequencing on 150 individuals from the F1DH population. The genetic map contained 1,696 bin-markers with 982,642 single-nucleotide polymorphisms (SNPs) spanning a total distance of 775.81 cM on all nine chromosomes with an average distance between markers of 0.46 cM. The ornamental kale genetic map contained substantially more SNP markers compared with published genetic maps for other B. oleracea crops. The F1DH progenies provide an excellent resource for germplasm innovation and breeding new varieties of ornamental kale. The high-density genetic map provides crucial insights for gene mapping and unraveling the molecular mechanisms behind important agronomic traits in ornamental kale.

A 4×2 factorial experiment was conducted to evaluate the potential of feeding dietary gamma-oryzanol and vitamin E tocotrienols in hens reared in 840 (low cage density; LCD) or 420 cm2/hen (high cage density; HCD). A total of 120 hens were allocated into eight groups with five replicates. Diets were a control (CON) or the control diet supplemented with 200 ppm gamma-oryzanol (GO-200), 200 ppm vitamin E tocotrienols (VE-200) or 200 ppm gamma-oryzanol + 200 ppm vitamin E tocotrienols (GE-400). Results showed that HCD-housed hens decreased (P &lt; 0.01) egg performance and quality. Average egg weight (AEW), egg mass and FCR improved in all supplemented treatments. Results on the AEW, FCR, and eggshell qualities of birds kept at the HCD revealed the best responses in the GE-400 group (P &lt; 0.01). Among hens kept on an HCD, there was a noticeable decrease in HMGCR mRNA abundance in the VE-200 group, while the highest IFN-γ mRNA abundance was found in hens fed the GO-200 diet (P &lt; 0.05). Thus, this study suggested that dietary GO or VE at 200 ppm either individually or in combination could improve performance and egg quality as well as regulate the abundance of immune- and stress-related genes.

Staphylococcus aureus is a common pathogen in human. Methicillin resistant Staphylococcus aureus (MRSA) infection poses a big and perplexing difficulty in terms of therapy. The acquisition of the non-native gene PBP2a, which has a decreased tolerance for β-lactam antibiotics, frequently confers resistance. PBP2a has a less attraction for methicillin and it helps bacteria to continue peptidoglycan biosynthesis, and it is cell wall’s core component in bacteria. So, even in the presence of methicillin or any other antibiotic, bacteria develop resistance. Due to resistance-causing genes, S. aureus becomes MRSA. The main premise of the resistance mechanism is well understood. The current demand for novel antibiotics is legitimate in the face of therapeutic concerns posed by resistant micro-organisms. The emphasis of this review is on PBP2a scaffolds and the different screening approaches used to find PBP2a inhibitors. Penicillin, Cephalosporins, Pyrazole-Benzimidazole based derivatives, Oxadiazole containing derivatives, non-β-lactam allosteric inhibitors, 4-(3H)-Quinazolinones, Pyrrolylated chalcone, Bis-2-Oxoazetidinyl macrocycle (β-lactam antibiotics with 1, 3-Bridges), Macrocycle-embedded β-lactams as novel inhibitors, Pyridine-Coupled Pyrimidinones, novel Naphthalimide corbelled aminothiazoximes, non-covalent inhibitors, Investigational-β-lactam antibiotics Carbapenem, novel Benzoxazole derivatives, Pyrazolylpyridine analogues, and other miscellaneous classes of scaffolds for PBP2a are also represented as well as with their biological activity is discussed. The penicillin-binding protein is also discussed, which is the crucial target for the cell wall of MRSA. Various aspects of PBP2a, the cell wall of bacteria, peptidoglycans, different crystal structures of PBP2a, synthetic routes for PBP2a inhibitors, and future perspectives of MRSA inhibitors are also enumerated.

Abstract: An Al-Co-Y diffusion coating was prepared on a TiAl alloy by pack cementation process at a low temperature range of 650-720 ℃. The influence of different activators and co-deposition temperatures on the coating’s microstructure and formation process, and high temperature oxida-tion performance was studied. The results showed that NaF was a more suitable activator for preparing the Al-Co-Y diffusion coating on TiAl alloy compared to NH4Cl and AlCl3. A more compact coating structure can be obtained when deposition was performed at 680 ℃ using NaF as the activator. The coating was mainly composed of a TiAl3 outer layer, a TiAl2 inner layer, and a thin Al-rich TiAl inter-diffusion layer. The growth of the coating exhibited a positive linear correlation between coating thickness increase and the square root of deposition time. The high-temperature oxidation tests showed that a dense scale mainly composed of Al2O3 and a small amount of TiO2 formed on the coating after oxidation at 950 ℃ for 100 h. The scale possessed excellent high-temperature oxidation resistance, with a parabolic rate constant of the oxidation weight gain approximately 4.9×10-3 mg2/cm4 h, which is lower than that of the TiAl substrate by about three orders of magnitude, and lower than that of the pure Al diffusion coating more than one order of magnitude.

Microemulsions with excellent properties have shown significant potential for enhancing oil recovery from tight formations through spontaneous imbibition. This work present a high-temperature-tolerant lower-phase microemulsion (HTLP-ME) using a microemulsion dilution method. The properties and morphological characteristics of HTLP-ME were evaluated and proposed a enhanced spontaneous imbibition oil recovery mechanism using imbibition tests and CT scanning technology. The results show that the optimum concentration of HTLP-ME is 0.2wt% has a superior thermal stability, small particle size, lower IFT, good wettability alteration ability, and minimum adsorption loss. Imbibition and CT experiments showed that the longer the imbibition distance, the better is the effect on spontaneous imbibition oil recovery. Furthermore, the solubilization coefficient and self-driving force were defined and calculated to quantitatively analyze the imbibition mechanisms. The imbibition mechanisms demonstrate that the reduction of oil/solid adhesion is due to the synergistic effect of IFT reduction and wettability alteration, and the ability to increase the imbibition distance through a larger self-driving force.

In order to study the acoustic emission characteristics of sandstone under the action of the high temperature-water cooling cycle, the RMT-150B electro-hydraulic servo rock test system and the DS-5 acoustic emission detection and analysis system were used to conduct a single analysis of the sandstone after the high temperature-water cooling cycle. Experimental study on acoustic emission characteristics under axial compression, analyzing the deformation, strength and acoustic emission characteristics of sandstone under different temperatures and cycles. The results of the study show that the high temperature-water cooling action causes changes in the physical properties of the sandstone. The expansion rate of the rock sample decreases first and then increases when the temperature rises, and the strength first increases and then decreases. The number of cycles has little effect on the physical properties of the rock sample; sandstone acoustic emission ringing count increases with the increase of temperature and cycle times, acoustic emission activities become more frequent with the loading process; with the increase of cycle times and temperature, acoustic emission ringing counts and accumulative acoustic emission energy appear earlier The rock sample enters the elastic deformation stage ahead of schedule, the yielding period increases, and the rock sample presents a trend of transition from brittle failure to ductile failure; the ringing count and cumulative energy increase with the increase in temperature and cycle times, and the high-energy ringing count and cumulative energy increase. The simultaneous sharp increase of the rock sample is the harbinger of the failure and instability of the rock sample.

The incorporation of polycarboxylate ether superplasticizer (PCE) type polymer and silica fume (SF) in high-performance concretes (HPC) leads to the achievement of remarkable rheological and mechanical improvements. In the fresh state, PCEs are adsorbed on cement particles and dispersants, in turn promoting the workability of the concrete. Silica fume enables a very well compacted concrete to be obtained, which is characterized by high mechanical parameters in its hardened state. Some PCEs are incompatible with silica fume, which can result in the loss of slump and in poor rheological behavior. The main objective of the research is the study of the influence of three types of PCEs, which all have a different molecular architecture, on the rheological and mechanical behavior of high-performance concretes containing 10% of SF as a partial replacement of cement. The results show that the carboxylic density of PCE has an influence on its compatibility with SF.

This paper proposes a novel symmetrical active-switched coupled-inductor high-step-up DC/DC converter. A new active-switched coupled inductor is used to allow much higher voltage gain of the proposed converter. The symmetrical circuit structure of the proposed converter evenly divides large input currents and reduce input current ripple by operating in interleaved mode so power density is increased. The switches also have low voltage stress. The operating principle and design considerations for the converter topology are described. The proposed converter with an input voltage of 40 V, an output voltage of 400 V and an output of 1000 W at a switching frequency of 50 kHz is implemented. The simulations and experimental results are thus depicted to verify the theoretical analysis. The highest efficiency is 95.5% at 200 W measured by using a HIOKI 3390. Consequently, the proposed converter is suitable for renewable energy generation systems that require high power, high voltage gain and high efficiency.

High-grade gliomas present a significant challenge in neuro-oncology because of their aggressive nature and resistance to current therapies. Boron neutron capture therapy (BNCT) is a potential treatment method; however, the boron carrier compounds used — such as 4-borono-L-phenylalanine (L-BPA) — have limitations. This study evaluated the use of boron-conjugated 4-iodophenylbutanamide (BC-IP), a novel boron compound in BNCT, for the treatment of glioma. Using in vitro drug exposure experiments and in vivo studies, we compared BC-IP and BPA, with a focus on boron uptake and retention characteristics. The results showed that although BC-IP had a lower boron uptake than BPA, it exhibited superior retention. Furthermore, despite lower boron accumulation in tumors, BC-IP showed significant survival improvement in glioma-bearing rats compared to controls. These results suggest that BC-IP, with its unique properties, may be an alternative boron carrier for BNCT. Further research is required to optimize this potential treatment modality, which could significantly contribute to advancing the treatment of high-grade gliomas.

At present, in the field of aviation industry, titanium alloy is mainly used to manufacture parts such as compressor disc, blade and casing of aircraft engine. When working, titanium alloy parts produce high temperature due to high-speed running friction, which makes the high temperature oxidation resistance and friction resistance of titanium alloy greatly reduced. When their working environment contains salt, titanium alloys are subjected to thermal corrosion, which limits their wider practical applications. This paper introduce the aluminide coating and its preparation methods. The characteristics and functional mechanism of three functional coatings for service environment, such as high temperature resistant alumina-based coating, thermal corrosion resistant alumina-based coating and wear-resistant alumina-based coating are summarized. Finally, the development direction of composite coatings of titanium and titanium alloys for complex service environment is prospected.

Breakage and damage of fiber optic cable fibers seriously affect the normal operation of fiber optic networks and it is important to quickly and accurately determine the type and location of faults when they occur. The advantages of wavelet transform in singular signal detection and signal filtering are used to analyze Optical Time Domain Reflectometer (OTDR) curve signal and the fault detection method of fiber communication link with no relay and large span in high altitude area is given, which realizes the accurate detection and location of optical fiber communication link fault events under strong noise. The theoretical analysis is basically consistent with the experimental data. The accuracy of optical fiber fault location has been greatly improved in performance. The method has been directly applied to the field detection of ultra-long optical fiber links in high altitude areas, which has certain significance for the future real-time monitoring of optical fiber cables.

At Mae-Moh power plant, Thailand, superheater tubes, which are exposed in fly ash environ-ment, often degrade due to solid particle erosion. To extend the service lifetime of the superheater tubes, the high velocity oxy-fuel (HVOF) thermal spray technique is used to deposit a protective coating on the material, SA213-T22 steel. In this work, the solid particle erosion of the Co-28Cr and WC-12Co coatings was investigated using erodent particle impingement at the angles of 30o and 90o with an average particle size of 60 μm. The erosion behavior of SA213-T22 with and without Co-28Cr and WC-12Co coatings was explained using ductile and brittle erosion modes. The erosion test resulted in the brittle mode for both Co-28Cr and WC-12Co coatings, while SA213-T22 without coating indicated the ductile mode. On the investigation of surface morphology, the Co-28Cr coating showed mostly microcracks in contrast with the WC-12Co coating, fracture, de-bonding and deep cavities were also observed. Erosion resistance of the Co-28Cr coating was significantly higher than the WC-12Co coating, due to high hardness, low porosity and high density of the coating.

Limited availability of expensive alloying elements elevates low-alloyed steels to a unique position in the field of lightweight construction and mass production. Quenching and partitioning (Q&P) heat treatments of low-alloyed steels with exceptional property combinations are particularly promising. In this study, we characterize for the first time a new low-alloyed steel to be processed by Q&P heat treatments. In combined experimental and numerical studies, we design a novel approach that effectively combines the short cycle times of press hardening with the excellent property profiles of Q&P-treated steels. We identify appropriate transformation parameters for Q&P heat treatments by dilatometric studies and we adjust a number of reference conditions with different isothermal holding times. By means of SEM analysis and XRD measurements, we show that different fractions of retained austenite result in different mechanical properties. Initial numerical designs of the process can identify varying temperature profiles and cooling rates depending on the position in the die. The results show that the geometry of the part plays a minor role, but the die temperature is the dominant factor for successful partitioning directly in the press hardening process.

Hardaliye, a traditional non-alcoholic beverage, made from red grape pomace from wine production and produced by lactic acid fermentation with addition of different concentrations of whole/ground or heat-treated mustard seeds and of sour cherry leaves. Short shelf life of hardaliye limits its consumption and search in trend to process hardaliye to extend its shelf life. Thus, high hydrostatic pressure treatment of hardaliye drink with determination of changes in physicochemical and sensory properties in addition to microbial inactivation were studied according to Box-Behnken design. Maximum 5.10±0.00, 4.21±0.00, 5.38±0.59 and 5.05±0.22 log reductions were obtained in total mesophilic aerobic bacteria, total mold and yeast, Brettanomyces bruxellensis and Lactobacillus brevis by HHP. Shelf-life studies of the hardaliye samples were conducted with optimum processing parameters of 490 MPa, 29 oC for 15 min with the response variables of OD520 and inactivation of L. brevis. Both control and HHP treated samples were stored at 4 and 22 C for shelf-life studies. While control samples at 4 and 22 °C were spoiled at the 15th and 3rd days, HHP treated samples were spoiled after 108th and 228th days, respectively.

This article addresses the problem of contact voltage increase caused by the low frequency oscillation of the train-grid system in the phase-separation process of the EMU. The article establishes the EMU-contact line-traction substation model, reveals the mechanism of low-frequency oscillation, and obtains the relationship between the separation phase angle of the pantograph with line and low-frequency oscillations. Methods to suppress the over-voltage during the low-frequency oscillation are proposed. The study shows that when the power phase angle of the pantograph-line separation is within the range of 60°~90° and 240°~270°, the voltage amplitude in the neutral zone is larger, the maximum amplitude can reach 52.2kV, and low-frequency oscillation will occur in the neutral zone. When low frequency oscillation occurs, the contact line voltage in the neutral zone is mainly 1/3 power frequency (16.7Hz). After installing an RC suppression device in the neutral zone, when the EMU enters the neutral zone, the absolute value of the voltage peak drops to below 20 kV. Compared with the situation where the suppression device is not connected, the absolute value of the voltage peak is reduced by nearly 60%. The study provides a basis for the design of the neutral zone of the contact line and the selection of the high-voltage equipment of the EMU.

Multi-level direct networks fueled by the evolving technology of active optical cables and increasing pin-bandwidth achieve reduced diameters and cost, with high-radix switches. These networks, like Dragonfly, are becoming the preferred aspirants for extreme high-performance parallel machines such as exa-scale computing. In this paper, we introduce a Hyper Z-Tree topology, which deploys the Z-Tree, a variant of fat-tree, as a computing node of a Generalized Hypercube (GHC) configuration. The resulting configuration provides higher bisection bandwidth, lower latency for some applications and higher throughput. Furthermore, the levels of the fat tree offer several path diversities across the GHC dimensions, hence conceding a more fault tolerant architecture. To profit from these path diversities, we propose two adaptive routing algorithms, which are extensions to the routing algorithm suggested in HyperX topology. These two algorithms exhibit better latencies and throughput than the HyperX.

High-dimensional measurement error data are becoming more prevalent across various fields. Research on measurement error regression models has gained increasing attention due to the risk of drawing inaccurate conclusions if measurement errors are ignored. When the dimension p is larger than the sample size n, it is challenging to develop statistical inference methods for high-dimensional measurement error regression models due to the existence of bias, nonconvexity of objective function, high computational cost and many other difficulties. Over the past few years, some works have overcome the aforementioned difficulties and proposed several statistical inference methods. This paper mainly reviews the current development on estimation, hypothesis testing and variable screening methods for high-dimensional measurement error regression models and shows the theoretical results of these methods with some directions worthy of exploring for future research.

This paper investigates the use of contactless power ultrasonic excitation to decrease the electrical impedance of the weld in laser welding. The literature extensively documents the impact of em-ploying contact power ultrasonic excitation on the microstructure morphology and refinement of grain in the weld. This study involves characterizing an industrial High Power Ultrasound Transducer (HPUT) by determining the optimal distance and angle for contactless excitation of the fusion zone in the weld, aiming to achieve the maximum amplitude. Subsequently, the transducer is integrated into the laser welding system, resulting in the creation of an ultrasonic-assisted welding system. To find the improvement due to the contactless vibration assistance, the welding area was char-acterised by an impedance ohmmeter device. The results indicate an approximately 6 % im-provement in the welding quality in terms of the impedance value, an important parameter for battery pack welding. In response to the issue of overheating in the industrial transducer during prolonged welding operations, an alternative transducer was proposed to overcome this challenge. Further investigations are carried out by the alternative transducer to find the effect of different wave types, namely, shear and compressional waves, on the welding quality. The contact vibration can excite the plate approximately 50 times higher in acceleration amplitude than contactless ex-citation. Nevertheless, enhancements of 10% and 6% are observed in the impedance value when utilising compressional and shear waves, respectively, as compared to the results obtained with contactless vibration.

Lifestyle physical activity (PA) and nutrition are known to be effective interventions in preventing and managing obesity related comorbidities is adult populations, but less so in children and adolescents. We examined the effectiveness of lifestyle interventions in children from minority ethnic populations in western high-income countries. Our systematic review included 53 studies involving 26045 children from minority ethnic populations within western countries, who followed lifestyle intervention programs lasting between 8 weeks and 5 years with an aim to prevent and/or manage childhood obesity and associated comorbidities, including adiposity and cardiometabolic risks. Studies were heterogenous in terms of lifestyle intervention components (nutrition, PA, behavioural counselling) and settings (community vs. schools and after schools). Our meta-analysis included 31 eligible studies and showed no significant effects of lifestyle interventions when they focused on body weight and body mass index (BMI) outcomes [pooled BMI mean change = -0.09 (95% CI -0.19, 0.01), p=0.09]. This was irrespective of the intervention program duration (< 6 months vs. ≥ 6 months), type (PA vs nutrition/combined intervention) and weight status (overweight or obese vs no normal weight), all showed no significant effects in the sensitivity analysis. Nonetheless, 19 of the 53 studies reported reduction in BMI, BMI z scores and body fat percentage. However, majority of lifestyle interventions adopting a quasi-design with a combined primary and secondary obesity measures (11 out of 15 studies), were effective in reducing obesity comorbidities of cardiometabolic risks including metabolic syndrome, insulin sensitivity, and blood pressure in children with overweight and obesity. Preventing childhood obesity and associated comorbidities in children from high-risk ethnic minority groups is best achieved using a combined PA and nutrition intervention approach, which jointly target preventing obesity and cardiometabolic disease primary and secondary outcomes, especially measures of diabetes, hypertension, and cardiovascular disease.

INTRODUCTION There have been several advances in the treatment of hepatitis C virus (HCV) infection which have resulted in major reductions in the morbidity and mortality from liver-associated disease. These are not widely available in the Caribbean, due in part, to lack of knowledge of the epidemiology of infections with HCV. As efforts are made to eliminate HCV from the region, these and other existing barriers such as lack of an established database on HCV must be addressed. This review seeks to identify gaps in the knowledge of HCV in the Caribbean with respect to seroprevalence, genotype distribution and general epidemiologic characteristics. MATERIALS AND METHODS The literature for the period January 1, 2005, to October 2022, was reviewed to gather country specific data on HCV across the Caribbean. References were identified through indexed journals accessed through established databases. The usage pattern of HCV drugs was determined from data obtained from Pharmacists and Infectious Diseases Specialists across the region. RESULTS The prevalence of HCV in the Caribbean was 1.5%; the region should therefore be considered an area of moderate prevalence. Notably, data from specific countries were limited. The prevalence of HCV among intravenous drug users (21.9-58.8%); persons living with HIV/AIDS (0.8 to 58.5%); prisoners (32.8-64%) and men who have sex with men (MSM) (0.8-6.9%) was generally higher than in the general population (0.8-2.3%). Genotype 1 (83% was most prevalent followed by genotypes 2 (7.2%) and 3(2.1%), respectively. Drugs currently being used for treatment of HCV infections across the Caribbean include Epclusa (Sofosbuvir/velpatasvir), and Harvoni (Ledipasvir/sofosbuvir). Some of these drugs, are only available in the private sector and are sourced externally whenever needed. CONCLUSION There is a paucity of current data on the seroprevalence of HCV in the Caribbean and well-designed prospective studies are indicated to drive the implementation of treatment and control programs for HCV in the region. Barriers which need to be first overcome include unavailability and high cost of drugs used to treat HCV infections, injecting drug use and limited access to medical care and laboratory testing.

Abstract: The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC 11 crystal structure was prepared by either induction melting and additive manufacturing with a se- 12 lective laser melting (SLM) process, starting from mechanically alloyed powders. Unlike induction 13 melting, the as-produced SLM alloy showed fine nitride and Cr-rich s phase precipitates. Mechan- 14 ical spectroscopy measurements were performed on specimens cold worked and/or recrystallized. 15 Young’s modulus values of (140±10) GPa and (90±10) GPa were measured at 300 K for induction 16 melted and SLM samples, respectively. The values increased to (160±10) GPa and (170±10) GPa for 17 recrystallized samples. Damping measurements as a function of temperature showed two peaks 18 which were attributed to dislocations bending and grain boundaries sliding. The peaks were super- 19 posed on a temperature increasing background.

Several studies have reported a relationship between autonomic dysfunction　 during tasks and Internet addiction. Changes within 24 h regarding heart rate variability (HRV) may be a more sensitive indicator than short term observations. We evaluated the influence of excessive Internet usage on HRV using a 24 h electrocardiogram (ECG) and examined acute changes during computer game tasks. A total 13 high school students and 22 young adults were recruited, and divided into excessive Internet user and non- excessive user groups based on Internet addiction test scores. The ECG was recorded continuously for 24 h by a wearable sensor and during two computer games (the Iowa gambling task and each participant’s preferred game) using a standard type ECG system. Multiple psychometric tests were also conducted. The excessive Internet user group exhibited clinically significant depressive symptoms, and higher self-reported scores for anxiety, impulsivity, autistic tendencies, and sleep problems than the non- excessive internet user group. There were weak differences within the 24 h high-frequency (HF) band power between two groups. During the Iowa gambling task, younger participants exhibited a reduced HF response, which may be related to weaker top- down self- regulatory mechanisms.

In engineering practice, various types of information data are affected by many factors during the collection process. For example, information data measurement errors are caused by equipment performance and the working environment. During the transmission of detection information, the signal distortion caused by energy loss and signal interference causes unpredictable detection errors in the collected information data. Through the study of fractional calculus theory, it was found that it is suitable for studying nonlinear, non-causal, and non-stationary signals, and has the dual functions of improving detection information and enhancing signal strength. Therefore, under the influence of many factors, we applied the fractional difference algorithm to the field of information data processing. Multi-sensor detection data fusion algorithm based on the fractional partial differential equation was adopted to establish its online detection data. A multi-sensor detection data fusion algorithm based on a fractional partial differential equation is established, which effectively fuses the information data detection errors caused by various influencing factors and greatly improves the detection accuracy of information data. The effectiveness of this method is proved through its application in an experiment.

Background: High blood pressure (BP) has been implicated as a major risk factor for cardiovascular diseases in several global populations, including in individuals of African ancestry. Despite the elevated burden of high BP-induced cardiovascular diseases in Africa and other global populations with African ancestry, limited genetic studies have been carried out to explore the genetic machinery driving this phenomenon. Methods: We performed univariate and multivariate analyses using Genome-wide association studies (GWAS) and summary statistics data of 77,850 individuals of African ancestry for systolic (SBP) and diastolic blood pressure (DBP) traits. The six independent cohorts used included individuals derived from the African Partnership for Chronic Disease Research (APCDR), the UK Biobank, and the Million Veteran Program (MVP). Subsequently, we annotated, prioritized, visualized, and interpreted our meta-analyses results using FUMA, to gain further insight into the molecular mechanism(s) that contribute to the genetics of BP traits. Finally, loci attaining genome-wide significance, GWS (p<5x10-8) were also followed up with Bayesian fine-mapping to identify potential causal variants. Results: Our meta-analyses altogether identified 350 GWAS SNPs for SBP (166 SNPs) and DBP (184 SNPs, including two novel loci) whilst our multivariate GWAS method identified 166 SNPs (including three novel loci). Interestingly, in FUMA there was significant tissue enrichment of up-regulated differentially expressed genes (DEGs) in the sigmoid and transverse colon for SBP, as well as 10 significant gene sets from MAGMA gene set analyses, However, for DBP, no significant DEGs nor gene sets in MAGMA were found; instead, in DBP for gene property analysis for tissue specificity nine candidates were found to be significant and all nine were in different brain regions. Finally, Bayesian fine-mapping revealed that only 11 variants from the lead SNPs had >50% posterior probability (PP) of being causal and they included novel variant rs562545 (MOBP, PP = 77%) and 10 other previously published variants. Conclusion: Our results demonstrate the importance of performing GWAS in large sample sizes of global populations of African ancestry, including continental Africans; which yield novel insights, from novel loci to novel pathways/tissue expression candidates. Large-scale genomic datasets are required to enhance further discovery and fine-mapping of high-risk loci/variants in highly susceptible groups for cardiovascular disease and other related traits. Our study highlights the need for diversity in genetic research and the importance of expanding large GWASs to include ancestrally diverse populations.

To create normative scores for all CrossFit® Open (CFO) workouts and compare male and female performances, official scores were collected from the official competition leaderboard for all competitors of the 2011-2022 CFO competitions. Percentiles were calculated in athletes (18 – 54 years) who completed all workouts within a single year ‘as prescribed’ and met minimum scoring thresholds. Independent t-tests revealed significant (p &lt; 0.05) sex differences for 56 of 60 workouts. In workouts scored by repetitions completed, men completed more repetitions in 18 workouts by small-to-large differences (d = 0.22-0.81), whereas women completed more repetitions in 6 workouts by small-to-medium differences (d = 0.36-0.77). When workouts were scored by time-to-completion, men were faster in 10 workouts by small-to-large differences (d = 0.23-1.12), while women were faster in three workouts by small differences (d = 0.46). In three workouts scored by load lifted, men lifted more weight by large differences (d = 2.00-2.98). All other differences were either trivial or not significant. Despite adjusted programming for men and women, the persistence of performances differences across all CFO workouts suggest resultant challenges are not the same. These normative values may be useful to training and research in male and female CrossFit® athletes.

New nanocomposite material was prepared by high pressure processing of starting glass of nominal composition NaFePO$_{4}$. Thermal, structural, electrical and dielectric properties of the prepared samples were studied by differential thermal analysis (DTA), X-ray diffraction (XRD) and broadband dielectric spectroscopy (BDS). It was demonstrated that high pressure – high temperature treatment (HPHT) led to an increase of electrical conductivity of initial glasses by 2 orders of magnitude. It was also shown that the observed effect was stronger than for lithium analogue of this material studied by us earlier. The observed enhancement of conductivity was explained by Mott’s theory of electron hopping, which is more frequent in sample after pressure treatment. The final composite consisted of nanocrystalline NASICON and alluaudite phases, which are electrochemically active in potential cathode materials for Na batteries. Average dimensions of crystallites estimated from XRD studies were between 40 and 90 nm, depending on the phase. Some new aspects of local dielectric relaxations in studied materials were also discussed. It was shown that a combination of high pressures and BDS method is a powerful method to study relaxation processes and molecular movements in solids. It was also pointed out that high-pressure cathode materials may exhibit higher volumetric capacities compared with commercially used cathodes with carbon additions.

Canola is the major oilseed crop of Canada. The de-oiled material is an important by-product due to its rich phenolic profile and high protein content. This co-processing stream from canola is primarily utilized as animal feed but represents an invaluable source of nutraceuticals. Microwave-assisted solvent extraction (MAE), as a green extraction method, has received considerable attention in recent times. The ease of use and application of many solvents at the same time makes the MAE one of the best methods for studying multiple solvents at the same time. The formation of canolol, from sinapine and sinapic acid, is primarily dependant on temperature which favors the decarboxylation reaction. Hence, MAE using green extractants can be used to enhance the yield of canolol. This study examined the effects of different pre-treatment temperature-time combinations of 140, 150, 160, and 170℃ for 5, 10, 15, 20 and 30 minutes on the extraction of canolol and other canola endogenous phenolic compounds. Three antioxidant assays assessed the antioxidant activity of the different extracts obtained by MAE confirming the microwave as a novel and versatile instrument for enhancing the yield of canolol. Improvements in the antioxidant activity of the different extracts further established the efficacy of the current method for isolating important natural phenolic derivatives for utilization by the nutraceutical industry.

Bauxite residue (BR), also known as red mud, is a by-product of the production of alumina via the Bayer process. Because of the high sodium oxide and other impurities content, this material is not used to obtain iron or other iron-containing products. In this paper, the hydro-chemical conversion of goethite (FeOOH) to magnetite (Fe3O4) in high-iron BR from the Friguia alumina refinery (Guinea) by Fe2+ ions in highly concentrated alkaline media was studied. The simultaneous extraction of Al and Na made it possible to obtain a product containing more than 96% Fe3O4. The results show that the magnetization of Al-goethite and Al-hemetite accelerates the dissolution of the Al from the iron mineral solid matrix and from the desilication product (DSP). After ferrous sulfate (FeSO4·7H2O) was added directly at the FeO:Fe2O3 molar ratio of 1:1 at 120 °C for 150 min in the solution with the 360 g L-1 Na2O concentration, the alumina extraction ratio reached 96.27% for the coarse bauxite residue size fraction (Sands) and 87.06% for fine BR obtained from red mud. The grade of iron (total iron in the form of iron element) in the residue can be increased to 69.55% for Sands and 58.31% for BR. The solid residues obtained after leaching were studied by XRD, XRF, TG-DTA, VSM, Mössbauer spectroscopy and SEM to evaluate the conversion and leaching mechanisms and the recovery ratio of Al from different minerals. The iron-rich residues can be used in the steel industry or as a pigment.

Drought and high temperature often occur simultaneously will eventually affect rice (Oryza sativa L.) yield and seed quality. The objective of the study was to compare the effects of high temperature (HT) and water limitation (WL) during seed development and maturation on yield component, seed quality, and amylose content in aerobic rice cv. MRIA. Two experiments were conducted concurrently in greenhouse with ⁓35/26℃ subjected to elevated HT and/or WL; 5 days 38/28°C at 10, 15, 29 DAA and/or HT; 7 days at 40/28℃ at 8 and 21 DAA with 12h photoperiod in control environment growth chamber. Both experiments were respectively harvested at physiological maturity of 31 and 35 DAA. Grain yielded from the irrigated plant declined from over 27% to below 18% between 15 and 29 DAA. Combination stresses resulted in greater reduction of grain yield than single stress. Late seed development (29 DAA) had no effect either on yield component or seed quality as well as produce a high concentration in amylase content (16.7%) with greater germination capacity (91%). The non-stress plant harvested at 21 DAA resulted the highest percentage of germinated seeds (97%) whereas the vigour index (VI) was reduced to 70.3% and 58.9% at 8 and 21 DAA respectively. Extended plant stress to 7 consecutive days incurred the highest VI with low concentration of amylose content. There was a linear relationship incurred between seed amylase content with germination capacity and VI, however, there was an inverse relationship (R2 = 0.19) between amylase content with VI from plant treated with (HT and/or WL) for 7 days. The present results confirmed that the avoidance HT and WL during early (10 DAA) and mid (15 DAA) seed development with short duration of stress (5 days) obtained better in yield component, enhanced the seed quality and amylose concentration. The combined HT and WL damaged seeds’ quality were more than each stress alone. Therefore, avoiding HT and WL can be practically applied by farmers by irrigating throughout the rice plant during histodifferentiation to save water usage during seed maturation.

The article is devoted to identifying promising research issues on the topic of Digital Industry based on the analysis of bibliometric data from Scopus platform for 2018–2022. The definition of promising issues derived from the titles, additionally abstracts, of highly cited works by authors with high publication activity. Authors' Scopus profiles were used to determine their affiliations, which are important for in-depth analysis of selected promising Digital Industry tasks. Metadata filtering to identify highly cited papers on particular issues was performed by keywords, Subject Areas, affiliations with countries and sponsoring organizations. Additionally, bibliometric metadata were clustered based on the co-occurrence of terms using VOSviewer. Within these clusters, articles of interest were identified for the formulation of promising research issues on the topic of Digital Industry, which will be subjected to in-depth analysis in separate papers.

By drilling periodic thru-holes in a suspended film, the phonon system can be modified. Being motivated by the BCS theory, the technique, so-called phonon engineering, was applied to a niobium sheet. The newly emergent high-T_c superconductivity, however, cannot be accounted for by the BCS theory. Rather, its exposed configuration, namely a square-lattice oxygen network, is reminiscent of the copper--oxygen plane in cuprate high-T_c superconductors. It turns out that its magnetic result is consistent with the principle of giant atom, which was developed by another heroes of superconductivity, Fritz London and John Slater, in the 1930s, several decades earlier than the propagation of BCS theory. The superconducting transition feature is discussed on the basis of a comprehensive theory of the giant atom---the theory of hole superconductivity.

The stress imposed by ethanol to Saccharomyces cerevisiae cells are one of the most challenging limiting factors in industrial fuel-ethanol production. Consequently, the toxicity and tolerance to high ethanol concentrations has been the subject of extensive research, allowing the identification of several genes important for increasing the tolerance to this stress factor. However, most studies were performed with well characterized laboratory strains, and how the results obtained with these strains work in industrial strains remains unknown. In the present work we have tested three different strategies known to increase ethanol tolerance by laboratory strains in an industrial fuel-ethanol producing strain: overexpression of the TRP1 or MSN2 genes, or overexpression of a truncated version of the MSN2 gene. Our results show that the industrial CAT-1 strain tolerates up to 14% ethanol, and indeed the three strategies increased its tolerance to ethanol. When these strains were subjected to fermentations with high sugar content and cell-recycle, simulating the industrial conditions used in Brazilian distilleries, only the strain with overexpression of the truncated MSN2 gene showed improved fermentation performance, allowing the production of 16% ethanol from 33% of total reducing sugars present in sugarcane molasses. Our results highlight the importance of testing genetic modifications in industrial yeast strains under industrial conditions in order to improve the production of industrial fuel ethanol by S. cerevisiae.

The article is devoted to solving the problem of searching for universal explainable features that can remain explainable for a wide class of objects and phenomena and become an integral part of Explainable AI (XAI). The study is implemented on the example of an applied problem of early diagnostics of plant stress, using Thermal IR (TIR) and HSI, presented by 8 vegetation indices/channels. Each such index was presented by 5 statistical values. A Single-Layer-Perceptron classifier was used as the main instrument. TIR turned out to be the best of the indices in terms of efficiency in the field and sufficient to detect all 7 key days with 100% accuracy. Our study shows also that there are a number of indices, inluding NDVI, and usual color channels Red, Green, Blue, which are close to TIR possibilities in early plant stress detection with 100% accurasy or near, and can be used for wide class of plants and in different conditions their treatment. The stability of the stress classification in our study was maintained when the training set was reduced up to 10% of the dataset volume. The entropy-like feature of (max-min) for any indices/channels have determined as a leadersheep universal high-level explainable feature for the plant stress detection, which used in interaction with some of other statistical features.

The purposes of this study are to analyze the groundwater quality of Ogallala Aquifer and evaluate the hydrological characteristics in the southern High Plains region of the Permian Basin, Texas. Levels of chloride, fluoride, nitrate, pH, selenium, and total dissolved solids (TDS) were analyzed through the years 1990-2016. A total of 133 wells were collected from the Texas Water Development Board (TWDB) which is an open database by the US government. Statistical analysis was utilized to evaluate the groundwater quality and propose trends. The average levels of the contaminants were compared to their respective Maximum Contaminant Levels (MCL) by the Environmental Protection Agency (EPA). Potential human health risks that each contaminant possesses were described. Possible sources of each contaminant were discussed with oil/gas activities, agricultural practices, and other human actions impact its conditions. This research provides important information for groundwater quality of Ogallala aquifer and contributes on understanding the response to development in the Permian Basin, Texas.

This study was carried out to determine the effects of apple vinegar and sodium diacetate addition on the aerobic stability of fermented high moisture maize grain (HMM) silage after opening. In the study, the effect of three different levels (0, 0.5, 1.0%) of apple vinegar (AV) and sodium diacetate (SDA) supplementation to fermented HMM at two different storage conditions (27-29°C, 48% Humidity; 35-37°C, 26% Humidity) were investigated. The material of the study was fermented rolled maize grain with 62% moisture content stored for about 120 days. Silage samples were subjected to aerobic stability test with 3 replicates for each treatment group. Wendee and microbiological analyses were made at 0, 2, 4, 7, and 12 days. Meanwhile, samples were displayed in the T200 IR brand thermal camera. According to the thermogram results, 1% SDA addition positively affected HMM silages at the second and fourth days of aerobic stability at both storage conditions (p<0.05). Aerobic stability and infrared thermography analysis indicated that 1% AV, 0.5%, and 1% SDA additions to HMM silages had promising effects. Due to our results, we concluded that thermal camera images might be used as an alternative quality indicator for silages in laboratory conditions.

Immunoglobulin G (IgG) adopts a modular multidomain structure that mediates antigen recognition and effector functions, such as complement-dependent cytotoxicity. IgG molecules are self-assembled into a hexameric ring on antigen-containing membranes, recruiting the complement component, C1q. To provide deeper insights into the initial step of the complement pathway, we report a high-speed atomic force microscopy study for quantitative visualization of the interaction between IgG and the C1 complex composed of C1q, C1r, and C1s. Results showed that C1q in the C1 complex is restricted regarding internal motion and has a stronger binding affinity for on-membrane IgG assemblages than C1q alone, presumably because of smaller conformational entropy loss upon binding. Furthermore, we visualized a 1:1 stoichiometric interaction between C1/C1q and an IgG variant that lacks the entire CH1 domain in the absence of antigen. In addition to the canonical C1q-binding site on Fc, their interactions are mediated through a secondary site on the CL domain that is cryptic in the presence of the CH1 domain. Our findings offer clues for novel-modality therapeutic antibodies.

We describe a method for protein quantification and for mRNA quantification in small sample quantities of human induced pluripotent stem-cell-derived-cardiomyocytes (hiPSC-CMs). Demonstrated here is how the capillary-based protein detection system Wes^TM by ProteinSimple and the Power SYBR^TM Green Cells-to-CT^TM Kit by Invitrogen can be applied to individual samples in a 96-well microplate format and thus made compatible with high-throughput (HT) cardiomyocyte assays. As an example of the usage, we illustrate that Cx43 protein and GJA1 mRNA levels in hiPSC-CMs are enhanced when the optogenetic actuator, channelrodopsin-2 (ChR2), is genetically expressed in them. Instructions are presented for cell culture and lysate preparations from hiPSC-CMs, along with optimized parameter settings and experimental protocol steps. Strategies to optimize primary antibody concentrations as well as ways for signal normalization are discussed, i.e. antibody multiplexing and total protein assay. The sensitivity of both the Wes and Cells-to-CT kit enables protein and mRNA quantification in a HT format, which is important when dealing with precious small samples. In addition to being able to handle small cardiomyocyte samples, these streamlined and semi-automated processes enable quick mechanistic analysis.

Insulin receptors are internalized by endothelial cells; however, the impact of hyperinsulinemia on this process is not known. Thus, the aim of this study is to determine the role of hyperinsulinemia on insulin receptor function and internalization, as well as the potential impact of protein tyrosine phosphatase 1B (PTP1B). To this end, hippocampal microvessels were isolated from male C57Bl/6J mice on either a control or high-fat diet and assessed for insulin receptor signaling. Cell surface insulin receptors in brain microvascular endothelial cells were labelled with biotin to assess the role hyperinsulinemia plays on receptor internalization in response to stimulation, with and without Claramine treatment, a potent PTP1B antagonist. Our results indicated that insulin receptor levels increased in tandem with insulin receptor dysfunction in the high-fat diet mouse hippocampal microvessels. Hyperinsulinemic cell-receptors demonstrate a shift in splice variation towards decreased IR-A/IR-B ratios and demonstrate a higher membrane-localized proportion. This corresponded with decreased autophosphorylation at sites critical for receptor internalization and signaling, however, Claramine restored signaling and receptor internalization in hyperinsulinemic cells. In conclusion, hyperinsulinemia negatively impacts brain microvascular endothelial cell insulin receptor function and internalization, likely through both alternative splicing and increased negative feedback from PTP1B.

Three-dimensional reconstruction plays an important role in assisting doctors and surgeons in diagnosing bone defects’ healing progress. Common three-dimensional reconstruction methods include surface and volume rendering. As the focus is on the shape of the bone, volume rendering is omitted. Many improvements have been made on surface rendering methods like Marching Cubes and Marching Tetrahedra, but not many on working towards real-time or near real-time surface rendering for large medical images, and studying the effects of different parameter settings for the improvements. Hence, in this study, an attempt towards near real-time surface rendering for large medical images is made. Different parameter values are experimented on to study their effect on reconstruction accuracy, reconstruction and rendering time, and the number of vertices and faces. The proposed improvement involving three-dimensional data smoothing with convolution kernel Gaussian size 0.5 and mesh simplification reduction factor of 0.1, is the best parameter value combination for achieving a good balance between high reconstruction accuracy, low total execution time, and a low number of vertices and faces. It has successfully increased the reconstruction accuracy by 0.0235%, decreased the total execution time by 69.81%, and decreased the number of vertices and faces by 86.57% and 86.61% respectively.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

Rapid isolation of white blood cells (WBCs) from whole blood is an essential part of any WBC examination platform. However, most conventional cell separation techniques are labor-intensive and low throughput, require large volumes of samples, need extensive cell manipulation, and have low purity. To address these challenges, we report the design and fabrication of a passive, label-free microfluidic device with a unique U-shaped cross-section to separate WBCs from whole blood using hydrodynamic forces that exist in a microchannel with curvilinear geometry. It is shown that the spiral microchannel with a U-shaped cross-section concentrates larger blood cells (e.g., WBCs) in the inner cross-section of the microchannel by moving smaller blood cells (e.g., red blood cells (RBCs) and platelets) to the outer microchannel section and preventing them from returning to the inner microchannel section. Therefore, it overcomes the major limitation of a rectangular cross-section where secondary Dean vortices constantly enforce particles throughout the entire cross-section and decrease its isolation efficiency. Under optimal settings, more than 95% of WBCs can be isolated from whole blood under high-throughput (6 ml/min), high-purity (88%), and high-capacity (180 ml of sample in 1 hour) conditions. High efficiency, fast processing time, and non-invasive WBC isolation from large blood samples without centrifugation, RBC lysis, cell biomarkers, and chemical pre-treatments make this method an ideal choice for downstream cell study platforms.

Farmers and seed companies constantly require high-quality seeds with excellent agronomic performance. However, faced with environmental adversity, limited natural resources and increasing food demand around the globe, more attention has turned to improving crop plant production by implementing efficient strategies. Seed priming technology has shown promising biological improvements leading to suitable agronomic performance in crop plants under adverse environmental conditions. Seeds are subjected to controlled conditions that are conducive to complex physiological, biochemical, and molecular changes, conferring specific stress tolerance to subsequent germination and growth conditions. In this review paper, we aimed to study the recent approaches in the efficiency of hydropriming, osmopriming, chemopriming, hormopriming, nanopriming, matrix priming, biopriming, physical priming and hybrid priming procedures in the production of crop plants under environmental adversity, as well as their biological mechanism changes. All priming methods demonstrated relevant changes in the biological mechanism related to crop plant production by mitigating salinity effects, heavy metals, and flooding stress and enhancing chilling, heat, drought and phytopathogen tolerance. We strongly recommend that researchers combine multiple priming methods, known as hybrid priming, in their investigations to provide novel technologies and additional biological approaches to enhance the knowledge of crop plant science. Thus, the findings shed light on the use of seed priming technology as a key strategy to increase crop plant production under environmental adversity by acquiring stress tolerance and enhancing agronomic traits to meet the global food demand.