Fractured media are seldom considered viable for storing excess thermal energy seasonally, compared to the more commonly used porous aquifers, due to their heterogeneity, lower storage capacity, and potential for unpredictable flow paths. This study employs COMSOL Multiphysics to create a numerical model of a fractured granite reservoir located below the Bedretto underground laboratory. The energy efficiency of both single-well and doublet systems was evaluated over 25 cycles, each comprising four 91-day phases: injection, storage, production, and resting. Results indicated that the single-well system was more efficient, with energy efficiency increasing with the flow rate. For an injection temperature of 60 °C, the system achieved energy efficiencies of up to 59.3% and 67.7%, after 10 and 25 cycles, respectively, aligning with porous Aquifer Thermal Energy Storage (ATES) system efficiencies at this temperature. Exploration of electricity production using water injected at 120 °C revealed it to be uneconomical and ineffective. However, the most promising use of the retrieved water was found to be direct ground heating for a greenhouse. This technology offers a potential alternative for thermal energy storage in regions lacking suitable porous aquifers, although identifying appropriate locations with the necessary geological characteristics may present significant challenges.

The electric vehicle (EV) industry challenges battery joining technologies by requiring higher energy density both by mass and volume. Improving the energy density via new battery chemistry would be the holy grail but is seriously hindered and progresses slowly. In the meantime, alternative ways, such as implementing more efficient cell packaging by minimizing the electrical resistance of joints are of primary focus. In this paper we discuss the challenges associated with the electrical characterisation of laser soldered joints in general, and the minimization of their resistive losses, in particular. In order to assess the impact of the joint resistance on the overall resistance of the sample, the alteration in resistance was monitored as a function of voltage probe distance and modelled by finite element simulation. The experimental measurements showed two different regimes: one far from of the joint area and another in its vicinity and within the joints cross section. The presented results confirm the importance of the thickness of the filler material, the effective and the total soldered area, and the area and the position of the voids within the total soldered area in determining the electrical resistance of joints.

Hemodynamic relevance of differently located stenoses of the internal jugular veins remains undetermined. It particularly concerns nozzle-like strictures in the upper parts of these veins and stenotic jugular valves located at the end of this vein. This study was aimed at understanding flow disturbances caused by such stenoses. Computational fluid dynamics software, Flowsquare+, was used. We constructed 3-dimensional models of venous outflow, comprising two alternative routes: tube representing the internal jugular vein and irregular network representing the vertebral veins. At the beginning of the tube representing the internal jugular vein, differently-shaped and sized short strictures, representing nozzle-like strictures were built in. At the end of this tube, differently-shaped membranes, representing the jugular valve, were built in. With the use of computational fluid dynamics modeling, we studied how these two obstacles influenced the outflow. We found that the most relevant outflow disturbances were evoked by nozzle-like strictures in the upper part of the internal jugular vein that were either small, long or asymmetrically positioned. Very tight stenotic valves and septum-like malformed valve were equally hemodynamically relevant. These findings suggest that both upper and lower strictures of the internal jugular vein can be of clinical significance.

This study focuses on the optimal deployment problem, and determines the optimal size of a military force to send to the battle field. The decision is optimized, based on an objective function, that considers the cost of deployment, the cost of the time it takes to win the battle, and the costs of killed and wounded soldiers with equipment. The cost of deployment is modeled as an explicit function of the number of deployed troops and the value of a victory with access to a free territory, is modeled as a function of the length of the time it takes to win the battle. The cost of lost troops and equipment, is a function of the size of the reduction of these lives and resources. An objective function, based on these values and costs, is optimized, under different parameter assumptions. The battle dynamics is modeled via the Lanchester differential equation system based on the principles of directed fire. First, the deterministic problem is solved analytically, via derivations and comparative statics analysis. General mathematical results are reported, including the directions of changes of the optimal deployment decisions, under the influence of alternative types of parameter changes. Then, the first order optimum condition from the analytical model, in combination with numerically specified parameter values, is used to determine optimal values of the levels of deployment in different situations. A concrete numerical case, based on documented facts from the Battle of Iwo Jima, during WW II, is analyzed, and the optimal US deployment decisions are determined under different assumptions. The known attrition coefficients of both armies, from USA and Japan, and the initial size of the Japanese force, are parameters. The analysis is also based on some parameters without empirical documentation, that are necessary to include to make optimization possible. These parameter values are motivated in the text. The optimal solutions are found via Newton- Raphson iteration. Finally, a stochastic version of the optimal deployment problem is defined. The attrition parameters are considered as stochastic, before the deployment decisions have been made. The attrition parameters of the two armies have the same expected values as in the deterministic analysis, are independent of each other, have correlation zero, and have relative standard deviations of 20%. All possible deployment decisions, with 5000 units intervals, from 0 to 150000 troops, are investigated, and the optimal decisions are selected. The analytical, and the two numerical, methods, all show that the optimal deployment level is a decreasing function of the marginal deployment cost, an increasing function of the marginal cost of the time to win the battle, an increasing function of the marginal cost of killed and wounded soldiers and lost equipment, an increasing function of the initial size of the opposing army, an increasing function of the efficiency of the soldiers in the opposing army and a decreasing function of the efficiency of the soldiers in the deployed army. With stochastic attrition parameters, the stochastic model also shows that the probability to win the battle is an increasing function of the size of the deployed army. When the optimal deployment level is selected, the probability of a victory is usually less than 100%, since it would be too expensive to guarantee a victory with 100% probability. Some of many results of relevance to the Battle of Iwo Jima, are the following: In the deterministic Case 0 analysis, the optimal US deployment level is 66200, the time to win the battle is 30 days and 14000 US soldiers are killed or wounded. If the marginal cost of the time it takes to win a victory doubles, the optimal deployment increases to 75400, the time to win a victory is reduced to 26 days, and less than 12000 soldiers are killed or wounded. In the stochastic Case 0 analysis, the optimal US deployment level is 65000, the expected time to win the battle is 46 days and almost 25000 US soldiers are expected to be killed or wounded. If the cost per killed or wounded soldier increases from 0 to 5 M $US, the optimal deployment level increases to 75000. Then, the victory is expected to appear after 35 days and 19900 US soldiers are expected to be killed or wounded.

This is the second in a series of two articles introducing the Gravitas computational general relativity framework, in which we now focus upon the design and capabilities of Gravitas's numerical subsystem, including its ability to perform general 3+1 decompositions of spacetime via the ADM formalism, its support for the definition and construction of arbitrary Cauchy surfaces as initial data, its support for the definition and enforcement of arbitrary gauge and coordinate conditions, its various algorithms for ensuring the satisfaction of the ADM Hamiltonian and momentum constraints, and its unique (totally-unstructured) adaptive refinement algorithms based on hypergraph rewriting via Wolfram model evolution. Particular attention will be paid to the seamless integration between Gravitas's symbolic and numerical subsystems, its ability to configure, run, analyze and visualize complex numerical relativity simulations and their outputs within a single notebook environment, and its capabilities for handling generic curvilinear coordinate systems and spacetimes with general (and often highly non-trivial) topologies using its specialized and highly efficient hypergraph-based numerical algorithms. We also provide illustrations of Gravitas's functionality for the visualization of hypergraph geometries and spacetime embedding diagrams in two and three dimensions, the ability for Gravitas's symbolic and numerical subsystems to be used in concert for the extraction of gravitational wave signals and other crucial simulation data, and Gravitas's in-built library of standard initial data, matter distributions and gauge conditions. We conclude by demonstrating how the numerical subsystem can be used to set up, run, visualize and analyze a standard yet nevertheless reasonably challenging numerical relativity test case: a binary black hole collision and merger within a vacuum spacetime (including the extraction of its outgoing gravitational wave profile).

Using numerical software to establish a three-dimensional geological model of shield tunneling through fault fracture zones, considering the synchronous grouting effect at the shield tail, the disturbance of various geotechnical structures in the fault fracture zone under deep burial and high water pressure conditions is studied. According to the comparison between the numerical model analysis results and the on-site inspection results of the entire process of Shiziyang B3 section, synchronous grouting at the shield tail is the main reason for the changes in soil and water pressure in the fault fracture zone area. The soil and water pressure changes strongly during shield tunneling, and the maximum excess pore pressure value occurs when the shield tail passes. When the shield tunneling machine is far away, the soil and water stress shows a downward trend. The impact of synchronous grouting decreases with the increase of tunneling distance. Due to the difference in permeability, the variation law of pore pressure in the fault fracture zone is significantly different from the original rock, leading to a faster increase in pore pressure in the fracture zone area and a wider range of influence.

The emerging industry of offshore wind turbines mounted on floating bases has garnered significant attention from both academia and industry. The desire to understand the complex physics of these floating structures has led to the development of numerical and physical modelling techniques. While physical testing has traditionally been employed, there is a growing focus on cost-effective and accurate high-fidelity numerical modelling as a potential alternative or supplement. However, commonly used numerical engineering tools in the offshore industry are considered mid- to low-fidelity and may lack the desired precision for floating offshore wind turbines (FOWTs). Given the complexity of these simulation codes, it is crucial to validate their accuracy. To address this, the International Energy Agency (IEA) Wind Technology Collaboration Programme initiated various research endeavors, including the Offshore Code Comparison Collaboration (OC3), Offshore Code Comparison Collaboration Continuation (OC4), Offshore Code Comparison Collaboration Continuation with Correlation (OC5), and the recent Offshore Code Comparison Collaboration Continued with Correlation and Uncertainty (OC6) projects. This study offers a comprehensive survey of the simulation tools available for FOWTs which were part of OC projects, focusing particularly on horizontal axis wind turbines (HAWTs) and highlighting their capabilities and fundamental theories.

Typhoid fever is an infectious disease that affects humanity worldwide particularly in the lower socio-economic communities where many individuals are exposed to a dirty environment and unclean food. A mathematical model is formulated to analyze the impact of control measures such as vaccination of susceptible humans, treatment of infected humans and sanitation in the different socio-economic communities. The model assumed that the population comprises of two socio-economic classes. The essential dynamical system analysis of our model was appropriately carried out. The impact of the control measures was analyzed, and the optimal control theory was applied on the control model to explore the impact of the different control measures. Numerical simulation of the models and the optimal controls were carried out and results obtained indicates that the overall combination of the control measures eradicates Typhoid fever in the population but the controls are more optimal in the higher socio-economic communities.

The oscillation of an elastically mounted rigid cylinder excited by steady fluid flow is investigated. Regarding the nonlinearity of real practical structures like marine risers and the stay cable of a long-span bridge, the dynamic behavior of the circular cylinder is described by double Duffing equations and the aerodynamic force performance of the wake flow is expressed by wake oscillator equation. Unlike previous studies, in the present investigation, attention is focused on coupling the wake oscillator equations, taking into account quadratic terms. Following this approach, the cylinder's combined cross-flow and in-line Vortex-Induced Vibrations (VIV) are modeled more accurately. Empirical coefficients are adjusted through comparison with previous credible experimental studies and the effects of changing coefficients of the quadratic terms on major VIV parameters are investigated. The oscillating amplitude calculated by the present model is close to that of the experiment. The relative error of results obtained by the present coupled model is lower than the previous model. Moreover, the present model successfully predicts the moving trajectories of a circular cylinder under VIV in a figure-of-eight shape.

Bending pipe is a common component of long distance pipeline. Accurately understanding the flow law of hydrate particles in elbow pipe is of great significance for optimizing pipeline design, improving production efficiency of gas transmission pipeline and ensuring pipeline safety. Taking the flow of hydrate particles in a Bending pipe as the object of study, the spiral flow attenuation and hydrate particle deposition under different bending pipe angles, different rate of bending pipe to diameter, different Reynolds number and different torsion were studied by numerical simulation method. The results show that the larger the swirl number, the higher the spiral flow intensity. When the fluid enters the bending pipe, the Angle of the bending pipe is larger, the torsional rate is smaller, and the Reynolds number is larger, the swirl number is larger, the intensity of the swirl flow is stronger, and the swirl number is larger at the same position. However, the larger the bending pipe to diameter ratio, the greater the change of the total swirl number and the weaker the strength at outflow, but the slower the change of swirl number, indicating that the spiral flow attenuation is slower. The larger the bending pipe Angle, the larger the bending pipe diameter rate, the smaller the torsion rate and the larger the Reynolds number, the smaller the deposition rate of the particles after flowing through the pipe. The results show that the spiral flow strength can be maintained in a proper way to reduce the deposition and ensure the safety of the conveying process.

The educational and play-related activities of children are proceeded mainly indoors in a kin-dergarten. The exposure of children to high concentrations of PM2.5 and CO2 indoors have leaded to various harmful effects and negatively impact educational outcomes in a kindergarten. Therefore, this study presents a numerical model of CO2 and PM2.5 concentration based on two classrooms in a kindergarten. Using this numerical model, we present different scenarios of oper-ating mechanical ventilation and air purifiers in kindergartens with the aim of optimizing for reducing the concentrations of CO2 and PM2.5. We found that the amount of ventilation required to maintain good air quality, per child, was approximately 20.4 m3/h. However, we also found that as the amount of ventilation increased, so did the concentration of indoor PM2.5; we found that this issue can be resolved through the use of a high-grade filter (i.e., a MERV 13 grade filter with a collection efficiency of 75%). This study provides a scientific basis for reducing PM2.5concentrations in kindergartens, while keeping CO2 levels low.

The practical necessity of strengthening of reinforced concrete structure elements requires a choice of a method which would provide cost-effectiveness, simplicity of construction and durability of the chosen solution. One of the ways is strengthening using the material belonging to the group of micro-reinforced concretes called ferrocement. The paper presents the comparative analysis of some of the results of RC beams exposed mainly to flexure, strengthened with ferrocement elements (strips) applied by gluing on the on the tensed side of RC beams. The results are obtained using the experimental, analytical and numerical research on the adequate models. Strengthening of the beams was performed in the form of four types of ferrocement strips (four different strip widths and four different numbers of wire mesh layers). The numerical non-linear analysis using finite elements method (FEM) was employed, with the introduction of the corresponding characteristics of constitutive material obtained by the experiments on the test specimens. The analytical researches were performed using known analytical calculation methods in order to formulate the model for the calculation of the ultimate and serviceability limit states of the strengthened cross-section. The results presented in the paper, through their comparative compatibility, confirmed the applicability of this strengthening method.

The flavor, aroma and color of coffee may change due to mechanical damage, reducing its qual-ity. To measure the mechanical response of materials, compression tests can be performed, de-termining the effect of force application on the mechanical behavior of the fruit at different stages of ripeness. In this context, this study aimed to analyze the deformation, strain energy and equivalent von Mises stress of coffee fruits at mature, semi-mature and immature maturation stages and compressed by collapse forces. Compression in three directions (x, y and z) was sim-ulated on coffee fruit models using the finite element method, with a compression support in the direction opposite to the force application axis. The numerical simulation of the compression process allowed to verify that the more mature the fruit, the greater the associated mean defor-mation (2.20 mm mm-1, 0.78 mm mm-1 and 0.88 mm mm-1), the lower the mean strain energy (0.07 mJ, 0.21 mJ and 0. 34 mJ) and the lower the mean equivalent von Mises stress (0.25 MPa, 1.03 MPa and 1.25 MPa), corresponding to ripe, semi-ripe and immature fruits; and these proper-ties may be used to analyze how processes in the production chain affect the amount of mechan-ical damage.

Paper is a material whose mechanical properties are highly dependent on humidity and temperature. Which naturally also builds the relationship between the stiffness and strength of corrugated board and changing weather conditions. In this paper, attention is focused on the dependence of the physical properties of the cardboard on changes in humidity and temperature, which undergo dynamic fluctuations both during the production of corrugated board and during its storage. Two techniques were used to test this effect, namely numerical homogenization and global sensitivity analysis. Both methods were implemented to determine the theoretical relationships between the change in humidity and/or temperature in each layer of corrugated board and its global bending, compression and shear stiffness. The procedure was used to analyze different types of 5-ply and 3-ply cardboard. The obtained results allowed to build a complete map of the relationship between the change in humidity of selected layers and the strength characteristics of the full assembly.

The article presents the results of testing the conditions of closing foundry voids during the hot forging operation of an ingot made of zirconium with 1% Nb alloy and use of the physical and numerical modelling, which is a continuation of research presented in a previous thematically related article published in the journal Materials. The study of the impact of forging operation parameters on the rheology zirconium with 1% Nb alloy was carried out on the Gleeble 3800 device. Using the commercial FORGE®NxT 2.1 program, a numerical analysis of the influence of thermo-mechanical parameters of the hot elongation operation in trapezoidal flat and rhombic trapezoidal anvils on the closure offoundry voids was performed. The analysis of the obtained test results was used to formulate recommendations on the technology of hot forging and the geometry of anvils, which ensure the closure foundry voids during the operation of hot forging

The damage evolution rules of coal under true triaxial combined static-dynamic loads are important to understand and reveal the mechanism of rockburst in coal mines. The numerical simulation was carried out using FLAC3D to explore the coupling effect of static and dynamic stress, especially the influence of dynamic load parameters. The results show that the increase of dynamic load amplitude not only makes the plastic zone grow exponentially and shorten the damage development time, but also decreases the residual strength of the coal sample, which leads to a much more violent of the dynamic failure. The stress wave can propagate more stable in the coal sample with the increase of dynamic load frequency and the development time of the plastic zone also show synchronous fluctuating features, and when the frequency is like the intrinsic frequency of the coal sample, the dynamic load has a significant stimulate effect. The static and dynamic loads have different damage effect to the coal sample under true triaxial stress path, the weight decreases in order of the minimum principal stress, the maximum principal, the amplitude of the dynamic load and at last the dynamic stress frequency by the entropy weight method analysis.

This paper presents some aspects of command and control of the new generation of machines-tools with numerical control. A problem faced by numerical control programmers is related to the length (relatively long) of the programs, with implications in the costs and duration of the manufacturing preparation. A method of reducing the main program and other redundant expenses is the introduction and use of processing cycles and subroutines for automatic calculation of the cutting tool trajectory, a fact that also allows the optimization and simplification of numerical control programming on flexible order manufacturing systems numeric. The method involves the use of predefined cycles and appropriate subroutines in order to improve the efficiency of the programming activity in a balanced way. It is a new and rapid method for optimize the structure of program using the numerical subroutine for command the movement of tool, in our case, with application for turning and milling.

The problems of formation and propagation of surface seismic waves in vertically layered and horizontally inhomogeneous media are studied. A mathematical model has been developed for the propagation of surface seismic waves in an inhomogeneous medium based on the use of the fundamental principles of wave dynamics and Fourier transforms. The existence of various types of groups of these waves is proved, and their main properties are studied. It has been established that the reflection coefficients of different groups of a dispersive wave on models of half-spaces (a layered, inhomogeneous medium) with a sharp velocity differentiation are characterized by the same dependence on the angle of incidence as in the absence of dispersion. In the region of the critical angle, which depends on the period of the incident wave, a local decrease in the intensity of wave reflection is observed, which is associated with the origin of the head dispersive wave. It has been found that the reflection coefficients of Rayleigh waves from low-velocity layers, thin (d / λ2 = 0.205) and thick (d / λ2 = 0.82) are approximately 0.2 ± 0.04 and practically do not change with increasing angle of incidence. On the basis of theoretical studies, it was revealed that reflected surface waves carry information both about the elastic properties of the reflecting medium and about the dimensions of the reflecting horizontal inhomogeneity. An experimental dispersion curve of the group velocity of Rayleigh waves on the Central Asia-Caucasus path has been obtained. The seismic stress state of the "subgrade-base" system was studied. Based on the analysis of the results of numerical experiments, it has been established that in order to obtain a complete picture of the seismically stressed state of the subgrade, it is necessary to take into account the contribution to it of each component of the accelerogram of a real earthquake.

In the present study, a simple approximation expression is given for the relationship between the period and amplitude of a simple pendulum under magnetic action. The analytical solution presented for the given problem. Two numerical quadrature methods Simpson's and Boole's method were utilized to demonstrate a new approximation of the problem. The results of the numerical quadrature have been compared to the exact solution. Absolute and relative mistakes of the problem have been presented. The Matlab program 2013R has created a numerical method that is used to analyze the outcome, It has been determined that the comparison's outcomes attest to the method's suitability and correctness. Moreover, the results show that numerical solution is suitable for the problem.

The twisted Wang transform distribution family, defined as the composition of parameter shifted inverse CDF function with an original CDF function, is found to be most suitable for matching low shape factor distributions, characterizing hard to fit or to simulate reinsurance portfolio losses for some perils from our previous study. Among them, the best form for matching a hard-to-fit empirical loss distribution for a specific peril, is the Exponential Fractional Extra Power 0 Distribution in (0,1) with CDF:.The simplest yet still a good form of this family is the Transformed Hyperbolic Tangent Distribution with CDF:,which has analytical formulas for the moments. The twisted Wang transform distribution family is compared and confirmed to be superior to all other well-known distribution families through extensive numerical optimization practice, distribution forms guesses, and computer-aided exploration experiments.

For embankment slope stability, soil cohesivity is one of the most important shear strength parameters. The effect of cohesiveness on the slope stability of a homogeneous embankment dam under rapid drawdown loading conditions was examined in this study. With the use of numerical modeling in GeoStudio, different situations were explored based on cohesiveness (0 kN/m², 5 kN/m², 10 kN/m^2, and 15 kN/m²) under a 1 m per day drawdown rate. The factor of safety value obtained from the long-term steady-state condition under 15 kN/m² cohesion was equivalent to a 116.8% increase from the one obtained under 0 kN/m² cohesion. The factor of safety values obtained after subjecting the embankment to different soil cohesion levels yielded a p-value of 1.91 x 10^-41, according to the Analysis of Variance. The calculated p-value (alpha value) is less than 0.05, suggesting that the differences between the examined cohesiveness values based on the list of the factor of safety values are statistically significant. The findings derived in this study show that it is significant to capture the effect of material characteristics during the design phase of an embankment dam.

ABSTRACT. In this paper, we suggest a biomathematical numerical method for analysing mRNA nucleotides sequences based on UA/CG Fibonacci numbers proportions. This method is used to evaluate then compare the spike genes related to the main SARS-CoV2 VARIANTS currently circulating within the world population. The 10 main results proposed to be reproduced by peers are: 1/ SARS-CoV2 genome and spike evolution in one year 2020-2021. 2/ SARS-CoV2 Origins. 3/ Comparing 11 reference variants spikes. 4/ analysing 32 CAL.20C California variant patients spikes. 5/ Toward a meta mRNA Fibonacci gene end message code. 6/ Analysing S501 UK, S484 South Africa and « 2 mutations » INDIA variants. 7/ Suggesting a possible variants spike mRNA palindrome symmetry metastructure improving mRNA stability then infectiousness. 8/ Analysing Fibonacci Metastructures in the mRNA coding for the vaccines PFIZER and MODERNA. 9/ Does the CG-rich modification of the synonymous codons of the spikes of the 2 mRNA vaccines affect the expression and quantity of SARS-CoV2 antibodies? 10/ The exceptional case of the Brazilian variant P.1. Particularly, we suggest the following conjecture at mRNA folding level : CONJECTURE of SARS-CoV2 VARIANTS: The growth of long Fibonacci structures in the shape of "podiums" for almost all of the variants studied (UK, California, South Africa, India, etc.) suggests the probable folding of the Spike mRNA in the form of a "hairpin", which can strengthen the cohesion and the lifespan of this mRNA. Finally, we show that these kinds of Fibonacci matastructures disapear TOTALLY by analysing the published mRNA sequences of PFIZER and MODERNA vaccines. One fact is certain, the two mRNAs of the Moderna and Pfizer vaccines will result in a low functionality of the spike vaccine. This is because their designers by seeking greater stability, have doped to build CG rich sequences which, as soon as they are inserted into the human host, will, paradoxically, seek to mutate, like SARS-CoV2 variants, towards CG ==> UA forms in order to improve their STABILITY and LIFETIME. We conclude using new biomathematics theoretical methods (Master code and numerical standing waves), and comparing the Spikes of the two vaccines Moderna and Pfizer, that there will be very probable differences in stability and shelf life of the two respective mRNAs vaccines. However, “State of the Art” analyzes will disclose that their two protein sequences are strictly identical. By modified their synonymous codons using different strategies, no one can guarantee that the quantity of antibodies generated will be identical in the two cases. We wish to draw attention to the great ADAPTATION power - at the global scale of their genomes - of the most infectious VARIANTS, such as the BRAZIL 20J / 501Y.V3 variant (P.1). This is very worrying for the VACCINES <==> VARIANTS run: We demonstrate how the Brazilian variant P.1 which becomes uncontrollable in Brazil in April 2021 has a level of organization of long metastructures of 17,711 bases covering the genome which is 3.6 more important than that of the 2 reference genomes SARS-CoV2 and worldwide D614G. We suggest that this high level of overall structure of this variant contributes to the stability of this genome and, might explain its greater contagiousness.

Wave is a common environmental load that often causes serious damages to offshore structures. In addition, the stability for the submarine artificial slope is also affected by the wave loading. Although the landslide of submarine slopes induced by the waves has received wide attention, the research on the influence of solitary-wave is rare. In this study, a 2-D integrated numerical model is developed to investigate the stability of the foundation trench under the solitary wave loading. The Reynolds-Averaged-Stokes (RANS) equations are used to simulate the propagation of a solitary wave, while the current is realized by setting boundary inlet/outlet velocity. The pore pressure induced by the solitary wave is calculated by Darcy’s law and the seabed is characterized by Mohr-Coulomb constitutive model. Firstly, the wave model is validated through the comparison between analytical solution and experimental data. The initial consolidation state of slope under hydrostatic pressure is achieved as the initial state. Then, the factor of stability (FOS) for the slope corresponding to different distance between wave crest and slope top is calculated with the strength reduction method. The minimum of FOS is defined as the stability index for the slope with specific slope ratio during the process of dynamic wave loading. The parametric study is conducted to examine the effects of soil strength parameters, slope ratio and current direction. At last, the influence of upper slope ratio in a two-stage slope is also discussed.

Air filtration mechanisms in the composite filter media used in practical applications are important and challenging to understand because the component fibers could have various size scales and morphologies. In this work, a three-dimensional digital model of nanofiber-based filter media was reconstructed for the first time based on the X-ray tomography data for the cellulose substrate and the Focused Ion Beam-Scanning Electron Microscope (FIB-SEM) image analysis for the several microns thick (3.82-7.90 μm) electrospun polyvinylidene fluoride (PVDF) nanofiber membrane. Besides the high-resolution model where the details of the fibrous structures were fully resolved, another low-resolution model with approximated unresolved structures was also established. Filtration simulations utilizing these models were conducted considering the drag force, Brownian diffusion and aerodynamic slip. The simulated filtration efficiencies agreed well with the experiments for particles of 70-400 nm, including the most penetrating particle size (MPPS, 100-200 nm). Moreover, the structure-resolved models had higher accuracy but higher computational costs, while the unresolved simulations saved much running time but over-predicted the filtration efficiency, especially for smaller particles (<100 nm). Our study presents a comprehensive strategy for investigating the composite filter media with multiscale complex structures using a combination of advanced characterization technologies and modular simulation models.

Automotive aerodynamics comprises of the study of aerodynamics of road vehicles. Its main goals are reducing drag, minimizing noise emission, improving fuel economy, preventing undesired lift forces and minimizing other causes of aerodynamic instability at high speeds. The Ahmed body has the form of a highly simplified car, consisting of a blunt nose with rounded edges fixed onto a box-like middle section and a rear end that has an upper slanted surface, the angle of which can be varied. It retains vital features of real vehicles in order to study the flow fields around it and the related turbulence models which characterizes the actual flow at elevated Reynolds number. In the present study, the aerodynamic behavior of this body is investigated numerically by the aid of commercial CFD tool: Ansys Fluent. The results of the simulation are validated with available experimental data and results of the simulations from other literatures. The numerical data were obtained for a fixed free stream velocity of 25 m/s at the inlet. The simulations were performed at a fixed slant angle of 25 degree and zero yaw angle. The present study focuses on how local refinement of mesh inside the concerned body and the outside, helps affect the results and for which grid dependency test is the primary objective of this paper. The present study also helps demonstrate how the drag of the body behaves, which is mainly the effect of pressure drag force generated at the rear portion of the body. The study also focuses on important properties like the velocity magnitude at different locations for different meshing cases, and to capture the flow pattern in the front or near the wake region. The study can be further helpful to future researchers in determining resistance, fuel efficiency etc. helping designers to optimize in specialized areas for better efficiency.

In this paper an integrated methodology for the coupling between 1D- and 3D-CFD simulation codes is presented, which has been developed to support the design and calibration of new diesel engines. The aim of the proposed methodology is to couple 1D engine models, which may be available in the early-stage engine development phases, with 3D predictive combustion simulations, in order to obtain reliable estimates of engine performance and emissions for newly designed automotive diesel engines. The coupling procedure features simulations performed in 1D-CFD by means of GT-SUITE and in 3D-CFD by means of Converge, executed within a specifically designed calculation methodology. An assessment of the coupling procedure has been performed by comparing its results with experimental data acquired on an automotive Diesel engine, considering different working points including both part load and full load conditions. Different multiple injection schedules have been evaluated for part-load operation, including pre and post injections. The proposed methodology, featuring detailed 3D chemistry modeling, was proven to be capable to properly assess pollutant formation, specifically to estimate NOx concentrations. Soot formation trend was also well-matched for most of the explored working points. The proposed procedure can therefore be considered as a suitable methodology to support the design and calibration of new Diesel engines, thanks to its ability to provide reliable engine performance and emissions estimations from the early-stage of a new engine development.

A conventional 2D numerical model is improved by incorporating three submodels to consider different effects of secondary flow and a module for cohesive sediment transport. The model is applied to a meandering reach of Yangtze River to investigate secondary flow effects on cohesive sediment deposition, and a preferable submodel is selected based on the flow simulation results. Sediment simulation results indicate that the improved model predictions are in better agreement with the measurements in planar distribution of deposition as the increased sediment deposits caused by secondary current on the convex bank have been well predicted. Secondary flow effects on predicted amount of deposition become more obvious during the period when the sediment load is low and velocity redistribution induced by the bed topography is evident. Such effects vary with the settling velocity and critical shear stress for deposition of cohesive sediment. The bed topography effects can be reflected by the secondary flow submodels.

Numerical modelling is becoming a major tool for supporting environmental studies at different scales, thanks to the capability of up-to-date codes in reproducing the natural behaviour in a quite reliable manner. In evaluating the habitat diversity of anthropized rivers, however, many issues are rising because of the intrinsic complexity of the processes involved. Using a reach of the Po River in Italy as a case study, the present works aims to provide an estimate of the changes of the Eco-Environmental Diversity as a response to different constant flow discharges. The goals are achieved by means of two solvers of the iRIC suite, applied in sequence to firstly simulate the fluvial hydrodynamics and subsequently provide an estimate of the habitat conditions. Despite the simplifications intrinsically present in the models and the ones introduced for practical purposes, the results pointed out that the reduction of the flow discharge recently observed can threat the overall biological status of the river. Because of the modelling uncertainties, on the other side, these preliminary outcomes show the need for more research, both in terms of data acquisition and numerical schematization, for adequately evaluate the effects of transient hydrology on the river ecosystems. Moreover, additional field surveys are necessary to calibrate and validate the used model for having sufficiently reliable estimates.

To improve the effect of multi-point stretch forming of sheet metal, it is proposed in this paper to replace fixed ball head with swinging ball head. According to the multi-point dies with different arrangements, this research establishes the finite element models of the following stretch forming, i.e. fixed ball heads with conventional arrangement, swinging ball heads with conventional arrangement, swinging ball heads with declining staggered arrangement, and swinging ball heads with parallel staggered arrangement and then numerical simulation is performed. The simulation results show that by replacing fixed ball head with swinging ball head, the surface indentation of the formed part was effectively suppressed, the stress and tension strain distribution of the formed part was improved and the forming quality was improved; that the thickness of the elastic pad was reduced, the springback was reduced and the forming accuracy was improved; and that when the ball head was applied to multi-point die with staggered arrangement, better forming result was achieved, where the best forming result was achieved in combining the swinging ball heads with the multi-point die with parallel staggered arrangement. The forming experiments were carried out, and the experimental results were consistent with the trend of numerical simulation results, which verified the correctness of the numerical simulation.

Structural vibration induced by dynamic load or natural vibration is a nonnegligible factor in failure analysis. Based on vibrating boundary condition, impact resistance of shape memory alloy reinforced composites is investigated. In this investigation, modified Hashin’s failure criterion, Brinson’s model and visco-hyperelastic model are implemented into the numerical model to charactering the mechanical behavior of glass fiber/epoxy resin laminates, SMAs and interphase, respectively. First, fixed boundary condition is maintained in simulation to verify the accuracy of material parameters and procedures by comparing with experimental data. Then, a series of vibrating boundaries with different frequencies and amplitudes are applied during the simulation process to reveals the effect on impact resistances. The statistics of absorbed energy and contact force indicate that impact resistance of the composite under high frequency and large amplitude is lower than that under low frequency and small amplitude, and summarized by a mathematical expression.

The steady streaming (SS) phenomenon is gaining increased attention in the microfluidics community, because it can generate net mass flow from the zero-mean vibration. We developed numerical simulation and experimental measurement tools to analyze this vibration induced flow, which has been challenging due to its unsteady nature. Validity of these analysis methods is confirmed by comparing the three-dimensional (3D) flow field induced around a cylindrical micropillar under circular vibration. In the numerical modeling, we directly solved the flow in the Lagrangian frame so that the substrate with a micropillar becomes stationary, and the result was converted to the Eulerian frame to compare them with the experimental results. The present approach enables to avoid the introduction of moving boundary or small perturbation approximation. The flow field obtained by the micro particle image velocimetry (PIV) measurement supported the three-dimensionality observed in the numerical results, which could be important for controlling the mass transport and manipulating particulate objects in the microfluidic systems.

Energy dissipation is one of the most important factors in choosing stepped spillways. However, few studies are about energy dissipation with different horizontal face angles. In this paper, the realizable k-ε turbulence model was used to study the flow field and energy dissipation rates of different stepped spillways with five horizontal face angles in the skimming flow regions. It shows that the free water surfaces and energy dissipation rates change with horizontal face angles and the energy dissipation rates initially decrease and then increase as the horizontal face angle increases. And the horizontal face angles cause the great changes of flow field.

Recently, there has been a growing interest in the production of electricity from renewable energy sources (RES). The RES investment is characterized by uncertainty, which is long-term, costly, depend on feed-in-tariff and support schemes. In this paper, we address the real option valuation (ROV) of a solar power plant investment. The real option framework is investigated. This framework considers the renewable certificate price, furthermore the cost of delay between establishing and operating the solar power plant. The optimal time of launching the project and assess the value of deferred option are discussed. The new three stage numerical methods are constructed, the Lobatto3C-Milstein (L3CM) methods. The numerical methods are integrated with concept of Black-Scholes option pricing theory, and applied in option valuation for solar energy investment with uncertainty. The numerical results of L3CM, finite difference and Monte Carlo methods are compared to show the efficiency of our methods. Our data set refers to the Arab Republic of Egypt.

Local polynomial smoother (LPS) is a weighted local least-squares nonparametric method. It provides a local Taylor series fit of the data at any location and can be directly used in a differential equation to provide a numerical scheme. In this article, we introduce this new nonparametric idea based on local polynomial smoother, for acquiring the numerical solution of the Bagley-Torvik fractional-order differential equations. Furthermore, this paper will present a numerical comparison with some methods, such as legendre operational matrix and pseudo-spectral method. The efficiency and accuracy of the LPS method are demonstrated by two numerical examples.

An innovative approach is utilized in this paper to solve the Fractional Fokker–Planck–Levy (FFPL) equation. A hybrid technique is designed by combining the finite difference method (FDM), Adams numerical technique, and physics-informed neural network (PINN) architecture, namely, the FDM-APINN, to solve the fractional Fokker‒Planck‒Levy (FFPL) equation numerically. Two scenarios of the FFPL equation are considered by varying the value of α (i.e., 1.75,1.85). Moreover, three cases of each scenario are numerically studied for different discretized domains with 100,200 and 500 points in x∈[-1,1] and t∈[0,1]. For the FFPL equation, solutions are obtained via the FDM-APINN technique via 1000,2000, and 5000 iterations. The errors, loss function graphs, and statistical tables are presented to validate our claim that the FDM-APINN is a better alternative intelligent technique for handling fractional-order partial differential equations with complex terms. FDM-APINN can be extended by using nongradient-based bioinspired computing for higher-order fractional partial differential equations.

In this research work, we developed a fractional-order model for the transmission dynamics of malaria, incorporating two control strategies: health education campaigns, and use of insecticides. The theoretical analysis of the model was presented, including the computation of disease-free equilibrium and basic reproduction number. We analyzed the stability of the proposed model using well formulated Lyapunov function. Furthermore, model parameter estimation was carried out using real data on malaria cases reported in Zimbabwe. We found that the fractional-order model provided a better fit to the real data compared to the classical integer-order model. Sensitivity analysis of the basic reproduction number was performed using computed partial rank correlation coefficients to assess the effect of each parameter on malaria transmission. Additionally, we conducted numerical simulations to evaluate the impact of memory effects on the spread of malaria. The simulation results indicated that the order of derivatives significantly influences the dynamics of malaria transmission. Moreover, we simulated the model to assess the effectiveness of the proposed control strategies. Overall, the interventions were found to have the potential to significantly reduce the spread of malaria within the population.

Multiple engineering projects have confirmed that hydraulic machinery operating in sediment-laden rivers suffers from sediment abrasion. Guide vanes are among the most severely worn flow-passing components and have long been a key research focus in hydraulic machinery. This study conducted wear tests using asymmetric incoming flow with a 10° impact angle and an NACA0012 aluminum alloy airfoil as the research object. The development of wear was analyzed, revealing that it primarily occurs at the airfoil’s leading edge and progresses through three stages: initiation, development, and stabilization. The Finnie model was used to analyze the initial wear mechanism, with calculated results closely matching the latest wear outcomes. In the initial stage, wear rate density was influenced by particle impact velocity, angle, volume fraction, and y-direction shear stress. A low-velocity zone near the impact point, combined with rebounding particles causing secondary impacts, increases particle volume fraction and wear rate density. These secondary impacts are the primary causes of wear on both the upstream and downstream surfaces. Furthermore, flow separation downstream of the leading edge makes this region highly susceptible to wear. This study provides valuable insights for addressing wear in hydraulic machinery for practical engineering applications.

The efficiency and the flame stabilization are two of the main parameters in the design of combustors according to the current policies imposed to the commercial aircraft industry. An alternative for flame stabilization and high efficiency in the combustion process in combustors is the concept of trapped vortex combustor (TVC). The objective of this study is to determine the optimal location and size of the injection holes for the airflow supplied to a TVC by means of a numerical simulation for non-reactive flow. The results showed a two vortex flow structures in the cavity that change their size and intensity according to the allocation and size of the injection holes. The total pressure lost, flow stability, velocity distribution, vortex size and intensity were the parameters for evaluating the different configurations. The optimal behavior was for a set of air injection holes at the top fore wall of the cavity in combination with a second set located at the bottom of the after wall.

It is expected that two-dimensional (2D) metal nitrides (MNs), consisting of the elements of the 13th group of the periodic table and nitrogen, namely aluminium nitride (AlN), gallium nitride (GaN), indium nitride (InN) and thallium nitride (TlN) have enhanced physical and mechanical properties, due to a honeycomb graphene-like atomic arrangement, characteristic to these compounds. The basis for the correct design and improved performance of nanodevices and complex structures based on 2D MNs of the 13th group is the understanding of the mechanical response of their components. In this context, a comparative study to determine the elastic properties of metal nitride nanosheets was carried out making use of the nanoscale continuum modelling (or molecular structural mechanics) method. The differences in the elastic properties (surface Young´s and shear moduli, and Poisson´s ratio) found for 2D 13th group MNs are attributed to the bond length of the respective diatomic hexagonal lattice. The results obtained contribute to a benchmark in the evaluation of mechanical properties of AlN, GaN, InN and TlN monolayers by analytical and numerical approaches.

Estuaries and deltas possess significant socioeconomic importance and exhibit high ecological value because of their dynamic geomorphic processes and unique geographical advantages. However, delta recession and the instability of river regimes have become worldwide issues due to intensive human interventions in upstream river basins and local areas in recent decades. This study focuses on a typical example, the South Branch of the Changjiang Estuary, to explore its morphological evolution in the past decades and near future and propose suitable solutions to enhance the stability of the river regimes. Based on bathymetric data analysis, we find significant channel-shoal adjustment within the South Branch from 1958 to 2016, characterized by substantial erosion and deposition on decadal timescales. After 1997, the South Branch experienced overall erosion due to the reduced fluvial sediment supply. Disturbances on the Baimao Shoal and Biandan Shoal further aggravated the river regime’s stability. Numerical predictions for future evolution trends indicate continuous erosion in the South Branch over the next 20 years, with further adjustments to the channel-shoal pattern. Hydrodynamic modeling of the proposed measures demonstrates an increased ratio for the North Baimao Shoal Channel, leading to enhanced stability of the channel-shoal system. These integrated governance measures have been incorporated in the new round of renovation planning for the Changjiang Estuary. The findings provide valuable scientific guidance for the comprehensive management of the Changjiang Estuary and offer insights applicable to other large estuaries.

In this study, the structural behavior of a short threaded anchor with a 20 mm diameter and an embedment length of 50 mm (2.5Ø) in UHPFRC is investigated using non-linear Finite Element models. UHPFRC is assumed to exhibit tensile strain-hardening behavior, with tensile strengths of 7 MPa and 11 MPa, respectively. The modelled anchor was subjected to a continuously increasing uniaxial pull-out force. The results indicate that the fracture mechanism of threaded anchors in UHPFRC is primarily characterized by the formation of a tensile membrane within the UHPFRC, which acts as the main resisting element against the pull-out force. Additionally, the influence of UHPFRC's tensile properties on the pull-out behavior and ultimate resistance of the threaded anchors was determined.

The geological and hydrological conditions of tunnels near reservoirs are complex, and the impact of water level changes on the stability and leakage assessment of the lining structure is not considered in the current leakage evaluation. In order to construct an evaluation model for leakage level of tunnels near reservoirs, the influence of water level changes on tunnel stability and changes in environmental conditions on the leakage of tunnels were researched. Based on the AHP and extensibility theory, a hierarchical system for leakage assessment, incorporating values from nine indexes representing three aspects: geological conditions, hydrological conditions, and tunnel engineering. Numerical simulation was used to analyze the influence of water level changes. It was found that the water level change index greatly influences the displacement and stress distribution inside the tunnel structure. The leakage evaluation model was applied to the Tiebeishan Tunnel, resulting in a rating of 3, indicating medium-level leakage. Attention should be paid to water leakage in tunnels with changes in reservoir water levels. The leakage evaluation model for tunnels near reservoirs can effectively assess leakage levels under various conditions, providing a reference for safety assessments of tunnel leakage near reservoirs.

The objective of this study, which is divided into two parts, is twofold: to address long standing challenges in the sensing of atmospheric turbulence-induced wavefront aberrations in strong scintillation conditions via comparative analysis of several basic scintillation resistant wavefront sensing (SR-WFS) architectures and iterative phase retrieval (IPR) techniques (Part I, this paper), and to develop a framework for the potential integration of SR-WFS techniques into practical closed-loop non-astronomical atmospheric adaptive optics (AO) systems (Part II). In this paper we consider basic SR-WFS mathematical models and phase retrieval algorithms, tradeoffs in sensor design and phase retrieval technique implementation, and methodologies for WFS parameter optimization and performance assessment. The analysis is based on wave-optics numerical simulations imitating realistic turbulence-induced phase aberrations and intensity scintillations, and optical field propagation inside SR-WFSs. Several potential issues important for practical implementation of SR-WFS and IPR techniques such as requirements for phase retrieval computational grid resolution, tolerance with respect to optical element misalignments, and the impact of camera noise and input light non-monochromaticity are also considered. Results demonstrate that major wavefront sensing requirements desirable for AO operation in strong intensity scintillations can potentially be achieved by transitioning to novel SR-WFS architectures based on iterative phase retrieval techniques.

This study presents the complexity and sensitivity of chaotic system dynamics in the case of the double pendulum. It applied detailed numerical analyses of the double pendulum in multiple computing platforms in order to demonstrate the complexity in behavior of the system of double pendulums. The equations of motion were derived from the Euler-Lagrange formalism, in order to capture the system's dynamics, which is coupled nonlinearly. These were solved numerically using the efficient Runge-Kutta-Fehlberg method, implemented in Python, R, GNU Octave, and Julia, while runtimes and memory usage were extensively benchmarked across these environments. Time series analyses, including the calculation of Shannon entropy and the Kolmogorov-Smirnov test, quantified the system's unpredictability and sensitivity to infinitesimal perturbations of the initial conditions. Phase space diagrams illustrated the intricate trajectories and strange attractors, as further confirmation of the chaotic nature of the double pendulum. All the findings have a clear indication of the importance of accurate measurements of the initial condition in a chaotic system, contributing to an increased understanding of nonlinear dynamics. Future research directions are faster simulations using Numba and GPU computing, stochastic effects, chaotic synchronization, and applications in climate modeling. This work will be useful for understanding chaos theory and efficient computational approaches in complex systems of dynamical nature.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

In rock blasting for mining production, stress waves play a major role in rock fracturing along with explosion gases. Better energy distribution improves fragmentation and safety, lowers production costs, increases productivity, and controls ore losses and dilution. Blast outcomes vary significantly with the choice of the explosive and the properties of the rock mass encountered. This study analyzes the effects of rock mass and explosives properties on the blast outcomes through numerical simulation using data from the case study and later validates the simulation results from the field blast fragmentation. The outcomes suggest that, for a given set of rock properties, the choice of explosive has a major influence on the resulting fragmentation. Strong explosives favor large fracture extents in hard rocks, while less strong explosives offer a better distribution of explosive energy and fractures. The presence of rock structures such as rock con-tacts and joints influences the propagation of stress waves and fractures depending on the structures' material properties, intensity and orientations, and the direction and strength of the stress wave. To achieve effective fragmentation, the blast design should mitigate the effect of variability in the rock mass by ensuring adequate energy distribution within the limits of geo-metrical design.

The application of numerical simulation methods for studying vertical-axis wind turbines offers significant advantages over conventional horizontal-axis wind turbines regarding wind energy utilisation, start-up wind speed, and environmental impact. This paper aims to investigate and establish the aerodynamic design performance of asymmetrical (NACA 4412) airfoils used in the application of vertical-axis wind turbines. The computational fluid dynamics (CFD) simulation uses Ansys software based on the Reynolds Averaged Navier-Stokes (RANS) equations. The aerodynamic parameters (pressure and velocity) are evaluated and compared within a range of angles of attack (AoA) 5-12 degrees at a fixed Reynolds number, as is a usual condition for wind turbine application. The lift coefficient (Cl), drag coefficient (Cd), and Cl/Cd ratio are obtained within the range AoA for the asymmetrical airfoils, and the performances have been predicted using the potential flow panel and CFD methods. This study suggests that while Xfoil may not be as precise as computational fluid dynamics (CFD), its predicted lift and drag coefficients generally align with experimental results. These help us to understand the best air-foil selection in a wind turbine application and predict its optimum AoA at which it performs at its best.

In the case of solid slabs made of reinforced concrete that are usually subjected to bending, large areas of the structure are stressed well below their load-bearing capacity or remain stress-free. Contrary to this are shell structures, which can bridge large spans with little material if designed well. To improve the efficiency of ceiling slabs, we want to utilize the shell load-bearing behaviour on a smaller scale by dissolving the solid interior accordingly. In order to be able to study a wide range of such constructions virtually, a parametric multiobjective simulation environment is to be developed in an ongoing research project, basic analysis approaches of which are presented in this paper. In addition to the basic workflow and the programs used, the material models used, and their calibration are described on the basis of tests on textile reinforced concrete (TRC) samples. Initial tests on two individual TRC served to verify the model.

The CMT (Cold Metal Transfer) arc welding process is a convenient instrument for the assembly of thin sheets [1], [2]. More particularly, it permits the decrease of the amount of heat transferred to the parts to-be assembled, thus reducing their subsequent deformations. The present work aims at simulating the CMT welding of thin stainless-steel sheets in order to develop an approach that allows the prediction of temperature fields, as well as final deformations induced by the welding process. For that purpose, instrumented tests and numerical simulations were set aiming at comparing the experiments with simulations. Butt-welding of stainless-steel sheets was considered, with a thickness ranging from 1 to 1.2 mm. The weld seam samples were observed in order to set an equivalent heat source for each configuration. Moreover, the electric current and voltage were surveyed, and temperature measurements were performed using K-type thermocouples. In addition, displacement measurements were obtained using the DIC (Digital Image Correlation) technique. Thermomechanical simulations were then carried out using an equivalent heat source approach, considering the phase changes of elements, i.e. the transitions from solid to liquid and from liquid to solid. These simulations also consider the actual geometry of seams induced by addition of a filler material.

The soil-structure interaction represents an important parameter when analyzing the dynamic behavior of bridges, taking into account the integration between soil, foundation, and structure to ensure an adequate structural representation. In this paper, a computational modeling strategy using soil-structure interaction (SSI) methodology was applied to represent the dynamic behavior of a pedestrian bridge (LOP). The computational models were validated using monitoring results from an extensive structural health monitoring campaign. The bridge monitoring program was characterized using embedded sensors and cutting-edge technology for remote monitoring: ground-based radar interferometry and video motion amplification. The instrumentation results were compared to establish the capabilities and advantages of this novel remote monitoring technique. The experimental results obtained from free and forced vibrations in the asset served as a basis for validating the developed computational model and allowed evaluating the asset be-havior in service for different loading conditions. This paper emphasizes the SSI approach to represent the pedestrian bridge dynamic behavior more accurately, allowing computational models to represent the LOP structural responses over the course of its life-cycle.

Folk residence in the cold region of Northeast China is an important part of China's traditional folk residence, with significant geographical representation. In this paper, we take the residential compounds of villages and towns in the cold region of Northeast China as the research object, summarize four typical layout forms of residential compounds of villages and towns in the cold region of Northeast China, simulate the wind environment of compounds of different layout forms in winter by using the computer numerical simulation software Fluent, and then analyze and evaluate the wind environment of compounds by combining with the evaluation standard of wind speed ratio and considering the area of wind shadows, number of vortices and other factors.

This study develops a new definition of fractional derivative that mixes the definitions of fractional derivatives with singular and non-singular kernels. Such developed definition encompasses many types of fractional derivatives, such as the Riemann-Liouville and Caputo fractional derivatives for singular kernel type as well as the Caputo-Fabrizio, the Atangana-Baleanu and the generalized Hattaf fractional derivatives for non-singular kernel type. The associate fractional integral of the new mixed fractional derivative is rigorously introduced. Furthermore, newly numerical scheme is developed to approximate the solutions of a class of fractional differential equations (FDEs) involving the mixed fractional derivative. Finally, an application to computational biology is presented.

An investigation of compressible flow over two-dimensional obstacles is presented in this paper. When shock waves are formed on surfaces due to compressibility and these shocks interfere with the boundary layer, undesirable effects such as friction, separation, and flow instability occur. To weaken the shock and reduce its effects, various methods have been employed in the past, including surface suction, surface blowing, and vortex generators. Using numerical solutions, the present work attempts to reduce the negative effects of the shock generated by the obstacle by creating porosity on its surface. Numerical methods such as the finite volume method and the Navier-Stokes equations as well as the Spalart-Allmaras model are used. By creating suction and blowing and increasing the cross-sectional area of the flow, porous surfaces reduce the effects of shock. Achieving around 50% porosity on the obstacle weakened the shock and reduced the Mach number after it, according to this paper's results. Also, the area under the skin friction diagram has decreased by about 38% as a result of less interference between the shock and the boundary layer and blowing caused by the porous surface.

The steel grid structure with bolted ball joints is gaining popularity in offshore platforms and aquaculture cages, but the corrosion resistance of these joints is a critical safety concern. This article introduces an innovative method to enhance the sealing performance of bolted ball joints, preventing seawater ingress and corrosion. The approach involves creating a sealed surface within the contact gap between the sleeve and connecting components. Circular grooves and sealing washers are added to both ends of the sleeve. A two-dimensional finite element analysis model of the bolted ball joint with the sealing structure was created using SOLIDWORKS and ANSYS. The study analyzes the sealing gasket's contact pressure at various compression levels and evaluates its performance with bubble tests for air tightness. Research results show a linear relationship between contact pressure and compression rate, with a sealing pressure of 5.95MPa achieved at a 14% compression rate. This simple, cost-effective sealing method effectively prevents corrosion from seawater, making it ideal for marine environments.

In the process of construction and operation of the pumping station, a large number of axial flow pumps pose a threat to the survival of fish in the natural environment. Through experiments, the survival conditions of many kinds of fish in extreme positive and negative pressure environment are explored, and -40 kPa is established as the low pressure damage threshold, which is used as a reference to analyze the probability of fish damage caused by pumps. The immersion boundary-lattice Boltzmann numerical method (LES-IB-LBM) based on large eddy simulation is used to optimize the parameters of the prototype runner of axial flow pump. A new type of runner with leading edge thickness of 11.4mm and blade cutting angle of 18 ° is optimized. This kind of runner has both hydraulic performance and fish-passing ability. The runner of the fish-friendly axial flow pump effectively guides the fish into the low risk area and reduces the risk of friction, shear and impact damage to the fish. the total impact mortality ratio of the runner of the axial flow pump before and after optimization is close to 7:1. The pressure damage analysis shows that the lowest negative pressure of the fish is -59.2 kPa, which is higher than -64.5 kPa of the prototype pump, and the highest positive pressure of the body surface is 11.8 kPa, which is lower than the 43.8 kPa of the prototype pump. Shear damage analysis shows that the fish will not be damaged by shear in the prototype pump and fish-friendly pump.

It is imperative to examine the performance of wind turbines both in steady and unsteady states due to their significant role in generating renewable energy by utilizing wind power. The computational fluid dynamics method (CFD) is one of the most efficient tools in this field, and the unsteady state has a great deal of importance when predicting turbine performance. Using the CFD method, the hydrodynamic performance of two types of offshore and onshore horizontal-axis wind turbines in the unsteady state was examined. Offshore wind turbines were modeled using the SST turbulence model and onshore wind turbines were modeled using the large eddy simulation (LES). Three-dimensional results of the simulation were compared and validated with experimental results, and good agreement between the two results indicates that the assumptions and method were accurate. Vortices were also studied in relation to the blade tip and their formation and development. Increasing the number of blades results in a reduction in torque, as well as a rise in vortices caused by the tips of the rotor blades. Due to the intensity of turbulence, the distribution of pressure on the surfaces will become irregular as the wind speed increases.

Controlling injection parameters is paramount when it comes to producing high-quality green parts using powder injection molding. This work combines experimental and numerical approaches to study the impact of injection parameters on mold in-cavity pressure and on the overall quality of green parts produced by low-pressure powder injection molding. The properties of two low-viscosity feedstocks (formulated from a water-atomized stainless-steel powder and wax-based binder system) were measured and implemented in an Autodesk Moldflow numerical model to quantify the molding pressures, which were finally validated using experimental real-scale injections. The results confirmed that an increase in mold temperature, an increase in feedstock temperature, and a decrease in solid loading decrease the mold in-cavity pressure, which was correlated with the feedstock viscosity. As a key result, real-scale injections confirmed that a minimum flow rate was required to avoid atypical high in-cavity pressure leading in several visual defects such as weld lines, flow marks, cracks, sinks, and incomplete filling. Due to differences in its thermal transfer properties, this flow rate threshold value decreases as the feedstock solid loading increases. For injection speeds higher than this value, the injection pressure measured experimentally was linearly correlated with the injection flow rate.

This work focuses on the research area of energy generation and harvesting for its transformation into electrical energy with the primary use of energy independent sensor systems in the power range P=10-10000W. These systems are applied in sensing quantities in the transport sector (bridge structures, transport infrastructure, and the others ). The proposed theoretical harvester models describing the transformation of motion energy into electrical energy, also provides theoretical and experimental models. Results obtained in the design and construction of a robust motion generator with primarily linear geometry system technology are presented. The expected output electrical power of the harvester is variable and is designed based on the linear motion generated by the engine- compressed air, small fuel system, etc. The fundamental design of the generator core has been continuously numerically modeled and an experimental setup has been developed to analyze specific parts and variations in order to validate the concept and achieve the most suitable parameters with the selected construction materials. A scaled down version of the model principle was tested in experiments and then the parameters and results were compared with the predicted theoretical analyses.

Recently, NOAA has included GNSS (Global Navigation Satellite System) Radio Occultation (RO) data as one of the crucial long-term observables for weather and climate applications. To include more GNSS RO data in the numerical weather prediction system, the NOAA Commercial Weather Data Pilot program (CWDP) started to explore the commercial RO data available on the market. After two rounds of pilot studies, the CDWP decided to award the first Indefinite Delivery Indefinite Quantity (IDIQ) contract to GeoOptics and Spire Incs. in 2020. This study examines the quality of Spire data products for weather and climate applications. Spire RO data are collected from commercial CubeSats through careful comparison with the data from Formosa Satellite Mission 7–Constellation Observing System for Meteorology, Ionosphere, and Climate-2 (COSMIC-2), ERA-5, and high-quality radiosonde data. The results demonstrated that although with lower Signal-Noise-Ratio (SNR) in general, the pattern of the lowest penetration height for Spire is similar to those for COSMIC-2. The Spire and COSMIC-2 penetrate heights are between 0.6 and 0.8 km altitude at the tropical oceans. Although using different GNSS RO receivers, the precision of Spire STRASP receivers is of the same quality as those of COSMIC-2 Global Positioning System - GPS, GALILEO, and GLObal NAvigation Satellite System – GLONASS (TGRS) receivers. The retrieval accuracy from Spire is very compatible with those from COSMIC-2. We validated Spire temperature and water vapor profiles by comparing them with collocated radiosonde data. Generally, over the height region between 8 km and 16.5 km, the Spire temperature profiles match those from RS41 RAOB very well with temperature biases &lt; 0.02 K. Over the height range from 17.8 to 26.4 km, the temperature differences are ~-0.034 K with RS41 RAOB being warmer. We also estimated the error covariance matrix for Spire, COSMIC-2, and KOMPSAT-5. Results showed that the COSMIC-2 estimated error covariance values are slightly more significant over the oceans at the mid-latitudes (45oN-30oN and 30oS-45oS), which may also be owing to COSMIC-2 SNR being lower at those latitudinal zones.

Distributions with bounded support show considerable sparsity over those with unbounded support, despite the fact that there are a number of real-world contexts where observations take values from a bounded range (proportions, percentages, and fractions are typical examples). For proportion modelling, a flexible family of two-parameter distribution functions associated with the exponential distribution is proposed here. Mathematical and statistical properties of the novel distribution are examined, including quantiles, mode, moments, hazard rate function, and its characterization. The parameter estimation procedure using the maximum likelihood method was carried out, and applications to environmental and engineering data were also considered. To this end, various statistical tests are used, along with some other information criterion indicators to determine how well the model fits the data. The proposed model is found to be the most efficient plan in most cases for the datasets considered.

This paper presents a numerical method for solving a two-dimensional subdiffusion equation with a Caputo fractional derivative. The problem considered assumes symmetry in both the equation’s solution domain and the boundary conditions, allowing for a reduction of the two-dimensional equation to a one-dimensional one. The proposed method is an extension of the fractional Crank-Nicolson method, based on the discretization of the equivalent integral-differential equation. To validate the method, the obtained results were compared with a solution obtained through Laplace transform. The analytical solution in the image of the Laplace transform was inverted using the Gaver-Wynn-Rho algorithm implemented in the specialized mathematical computing environment, Wolfram Mathematica. The results clearly show the mutual convergence of the solutions obtained by the two methods.

Nonlinear thermal transport of non-Newtonian polymer flows is an increasingly important area in materials engineering. Motivated by new developments in this area which entail more re-fined and mathematical frameworks, the present analysis investigates the boundary layer ap-proximation and heat transfer persuaded by a symmetrical cylindrical surface positioned hori-zontally. To simulate thermal relaxation impacts the bioconvection cross nanofluid flow Buongiorno model is deployed. The impact of the magnetic field applied on the nanofluid using the heat generation and melting phenomena are inspected. The nonlinear effect of thermosolutal buoyant forces is incorporated into the proposed model. The novel mathematical equations comprise thermophoresis and Brownian diffusion effects. Via robust transformation techniques, the primitive resulting partial equations for momentum, energy, concentration, and motile living microorganism are rendered into nonlinear ordinary equations with convective boundary postulates. An explicit and efficient numerical solver procedure in Mathematica 11.0 programming platform is developed to engage the nonlinear equations. The consequence of multiple governing parameters on dimensionless fluid profiles is inspected through plotted visuals and tables. Finally, outcomes declared on the surface drag force, heat, and mass transfer coefficients are exhibited through 3D visuals via different influential parameters.

In recent years discrete element method (DEM) has gradually been applied to the traditional fluidization simulation of fine particles in micro fluidized bed (MFB). The application of DEM in simulating fast fluidization of fine particles in MFB has not yet received attention. This article presents a drag model that relies on the surrounding environment of particles, namely particle circumstance-dependent drag modle or PCDD model. Fast fluidization in MFB of fine particles is simulated using DEM based on the PCDD model. It is found that the gas-solid two-phase flow in MFB meets the common law of fast fluidization in circulating fluidized bed (CFB) to a certain extent, and also presents a special law that is significantly different from that in CFB. Simulations indicate that the local structure in MFB exhibits particle aggregation which is a natural property of fast fluidized, forming a structure where continuous dilute phase and dispersed concentrated phase coexist. The formation and fragmentation of particle clusters in different local regions of the bed have time synchronization. There exists strong effect of solid back-mixing in MFB, leading to relatively low outlet solid flux. The gas back-mixing effect is, however, not so distinct. The axial porosity shows a monotonically increasing distribution with the bed height, but does not strictly follow the single exponential distribution. The solid volume fraction at the bottom of the bed is significantly lower than the correlated value in CFB. The axial heterogeneous distribution of the cross-sectional average porosity in the lower half of the bed is also weakened. The radial porosity shows a distribution pattern of higher in the central region and lower in the sidewall region. Compared with the correlation results in CFB, the porosity near the central region in MFB is relatively low, while the porosity near the sidewall region is relatively high. The geometric size of the container, especially the radial size, is much smaller than that of a CFB. The relative area of contact between the MFB wall and particles is larger, and the wall friction factor becomes more significant. This may be the main reason for the time synchronization of particle agglomeration, severe particle back-mixing, low outlet solid flux, monotonically increasing axial porosity and weak core-annular structure of radial porosity.

Nowadays, there are implemented devices whose purpose is to perform massive computations by saving resources at the time they reduce the latency of arithmetic operations. These devices are usually GPUs, FPGAs and other specialised devices such as "Coral". Neural networks, digital filters and numerical simulators take advantage of the massively parallel operations of such devices. One way to reduce the amount of resources used is to limit the size of the registers that store data. This has led to the proliferation of numeric formats with a length of less than 32 bits, known as short floating point or SFP. We have developed several SFP’s for use in our neural network accelerator design, allowing for different levels of accuracy. We use a 16-bit format for data transfer and different formats can be used simultaneously for internal operations. The internal operations can be performed in 16-bit, 20-bit and 24-bit. The use of registers larger than 16-bit allows the preservation of fractional information while increasing precision. By leveraging some of the FPGA’s arithmetic resources, our design outperforms designs implemented from scratch and is competitive with specialized arithmetic circuits already implemented in the FPGA.

Polymethyl methacrylate (PMMA) polymer is widely used in various fields today. In order to thoroughly reveal the structural impact performance of PMMA materials, this paper is based on the comprehensive Johnson-Cook constitutive model and damage failure model, and accurately confirm the J-C constitutive and damage failure model parameters of PMMA through material test data, The dynamic process of steel bullet impacting PMMA plate structure is analyzed by finite element software ABAQUS. The calculation results show that the numerical simulation results in this paper are in good agreement with the experimental test data. Therefore, the feasibility and accuracy of the impact analysis of PMMA structures based on J-C constitutive and damage failure models in this paper are studied. Finally, based on the J-C constitutive model and damage failure model, the variation of the residual velocity of the bullet with the PMMA plate thickness is analyzed in depth, that is, the results show that the residual velocity of the bullet has a certain linear relationship with the plate thickness.

Taking Shanxi Province, a typical energy region in China, as the research object, data on economic development quality and environmental pollution intensity from 2001 to 2021 were selected. Linear regression, numerical simulation, and Pearson correlation coefficient were used to analyze the evolution characteristics of economic development quality and environmental pollution intensity in Shanxi Province in the past 20 years, and to explore the relationship between economic development and environmental pollution. The results indicate that since 2001, Shanxi Province has made long-term progress in economic development, with GDP increasing by nearly 10 times and an average annual growth rate of around 7%. In the past 20 years, the main pollutants have shown a trend of increasing first and then decreasing steadily, with a turning point occurring during the "12th Five Year Plan" period. This shows that the environmental policies and investments of the Chinese and Shanxi provincial governments in the past 10 years have been effective in the new era. The numerical simulation curve results show that the per capita GDP exhibits a classic inverted "U" curve relationship with wastewater and SO2 emissions, with a turning point occurring at around 20000 yuan per capita GDP; However, there is a monotonic decreasing trend with Chemical oxygen demand and ammonia nitrogen emissions, and a monotonic increasing trend with solid waste generation. There is no turning point yet. The correlation analysis results further support the fitting curve conclusion.

The amplified Arctic warming is one of several factors influencing atmospheric dynamics. In this work, we consider a series of numerical experiments to identify the direct role of the Arctic sea ice reduction process in forming climatic trends in the northern hemisphere. Aimed at this, we used two more or less independent mechanisms of ice reduction. The first is traditionally associated with increasing the concentration of carbon dioxide in the atmosphere from the historic level of 360 ppm to 450 ppm and 600 ppm. This growth increases air temperature and decreases the ice volume. The second mechanism is associated with a reduction in the reflectivity of ice and snow. We assume that comparing the results of these two experiments allows us to judge the direct role of ice reduction. The most prominent consequences of ice reduction, as a result, were the weakening of temperature gradient at the tropopause level in mid-latitudes, the slower zonal wind at 50-60∘N, intensification of wave activity in Europe, Western America, and Chukotka, and its weakening in the south of Siberia and Kazakhstan. We also consider how climate change may alter regimes such as blocking and stationary Rossby waves. The study used the INM-CM48 climate system model .

The need for quick and easy deflection calculations of various prefabricated slabs causes that simplified procedures and numerical tools are used more and more often. Modelling of full 3D finite element (FE) geometry of such plates is not only uneconomical but often requires the use of complex software and advanced numerical knowledge. Therefore, numerical homogenization is an excellent tool, which can be easily employed to simplify a model, especially when accurate modelling is not necessary. Homogenization allows for simplifying a computational model and replacing a complicated composite structure with a homogeneous plate. Here, a numerical homogenization method based on strain energy equivalence is derived. Using the method proposed, the structure of the prefabricated concrete slabs reinforced with steel spatial trusses is homogenized to a single plate element with an effective stiffness. There is a complete equivalence between the full 3D FE model built with solid elements combined with truss structural elements and the simplified homogenized plate FE model. The method allows for the correct homogenization of any complex composite structures made of both solid and structural elements, without the need to perform advanced numerical analyses. The only requirement is a correctly formulated stiffness matrix of a representative volume element (RVE) and appropriate formulation of the transformation between kinematic constrains on RVE boundary and generalized strains.

The energy transfer process of laser selective melting is very complex. To study the effect of la-ser selective melting on the microstructure and properties of 18Ni-300 martensitic steel, ABAQUS was used to simulate the temperature of laser cladding 18Ni-300 martensitic steel at different time points and different laser power. The results show that the cross-section shape of the molten pool changes from round to oval With the increase of laser power, the higher the peak value of temperature time curve, the greater the temperature gradient; and the laser clad-ding experiment of 18Ni-300 martensitic steel was carried out, and the microstructure and me-chanical properties of the samples under different laser power were analyzed. The results show that with the increase of laser power, the grain size of the cladding layer becomes smaller and the microstructure becomes more compact; the hardness of the side surface of the sample is higher than that of the upper surface, and the tensile strength and elongation show a trend of first increasing and then decreasing.

The adoption of Pump as Turbines (PATs) both in small scale hydroelectric plants and water supply systems has brought different advantages, the most recognized being cost-effectiveness as compared to other hydroturbines. However, due to their lack of flow control ability, their intolerance to off-design operations constitutes one tough shortfall. Moreover, this technology’s newness leads to PAT flow dynamics still being ununderstood even to date. Therefore, this study intends to numerically investigate the mixed flow PAT’s pump mode flow dynamics for five operating conditions expanding from optimum (1QBEP) to deep part-load (0.41 QBEP) conditions. Moreover the effect of runner blade angle on the same has been investigated where three angles namely -2°, 0°, and 2° have been considered. PAT flow stability was found to deteriorate as the flow decreased, where associated pressure pulsation level worsened at different flow zones. In addition, the blade angle increase led correspondingly increasing flow unsteadiness and pressure pulsation levels, where the pulsation frequencies from rotor-stator interactions were dominant for most of flow zones. This study’s findings are of a crucial importance to both scientific and engineering communities as they contribute to thorough understanding of PAT flow dynamics.

Melt mixing is a convenient method to prepare polymer nanocomposites, but the extent of the dispersion of the solid filler reached is often limited, and may compromise the anticipated performance of these materials during service. Since the efficiency of extensional flows on dispersion is now well recognized, several mixers were designed with the aim of inducing both shear and extensional flow components. This work combines experimental and numerical data to better understand the kinetics of the dispersion of graphite nanoplates in a polypropylene melt, using a mixing device that consists of a series of stacked rings with equal outer diameter and alternating larger and smaller inner diameters, thus creating a series of converging/diverging flows. Numerical simulation of the flow using the opensource OpenFOAM software assuming both inelastic and viscoelastic responses predicted the velocity, streamlines, flow type and shear and normal stress fields for the mixer. Experimental and computed data were combined to determine the trade-off between the local degree of dispersion of the PP/GnP nanocomposite, measured as Area ratio, and the absolute average value of the hydrodynamic stresses multiplied by the local cumulative residence time. From considerations based on a theoretical approach to dispersion, the cohesive strength of the GnP agglomerates studied was estimated to be in the range 3 - 10kPa.

While the knowledge about the development of understanding positive integers is rapidly growing, the development of understanding zero is not well-known. Here we tested several components of preschoolers’ understanding zero: whether they can use empty sets in numerical tasks, whether they can use empty sets soon after they understand the cardinality principle, whether they know what the word “zero” refers to, and whether they categorize zero as a number. The results show that preschoolers can handle empty sets in numerical tasks as soon as they understand the cardinality principle or even earlier, and some of them know that these sets are labeled as “zero.” However, they are unsure whether zero is a number. These results identify three components of knowledge about zero: operational knowledge, linguistic knowledge, and meta knowledge. To account for these results we propose that preschoolers might understand numbers as the properties of items or objects in a set. In this view, zero cannot be a number, because an empty set does not include any items, and the missing items cannot have any property, excluding also the number property. This model might explain why zero is handled correctly in numerical tasks, while it is not regarded to be a number.

Due to the accuracy of numerical calculation of fluid flow inside a hydrocyclone can be obtained using Computational Fluid Dynamics (CFD), highly modified super computers are used to simulate the fluid flow and track particle motion inside a hydrocyclone. This paper deals with the numerical study using three multiphase models viz. Volume of fluid, Mixture and Eulerian model. The dimensions of the hydrocyclone taken into consideration for numerical analysis is same as considered by Rajamani. Validation of axial and tangential velocities at different strategically decided axial stations, RMS axial and tangential velocity profiles of the hydrocyclone is done using Reynolds Stress Model (RSM). The hydrocyclone model has been designed in Creo 3.0 using the same dimensions which later was imported to CFD for meshing. Fine hexagonal mesh numbering up to 5 lacs were constructed to obtain optimum results. Fluid flow was allowed to be developed in ANSYS FLUENT 16.2. Entire simulation took 96 hours to generate results and track particle movements inside the hydrocyclone. The particle tracking has been done using three multiphase model. The first being the volume of fluid was used for validation purposes and the comparison of the Mixture and Eulerian model are the basic focus of this research work. Conclusive results indicate that usage of different multiphase model does not result in variation in particle motion. The slight variation in grade efficiency values are hardly noticeable. The Mixture model and Eulerian model predict lower separation efficiency as compared with Volume of fluid multiphase model.

In this manuscript, an automated framework dedicated to design space exploration and design optimization studies is presented. The framework integrates a set of numerical simulation, computer-aided design, numerical optimization, and data analytics tools using scripting capabilities. The tools used are open-source and freeware, and can be deployed on any platform. The main feature of the proposed methodology is the use of a cloud-based parametrical computer-aided design application, which allows the user to change any parametric variable defined in the solid model. We demonstrate the capabilities and flexibility of the framework using computational fluid dynamics applications; however, the same workflow can be used with any numerical simulation tool (e.g., a structural solver or a spread-sheet) that is able to interact via a command line interface or using scripting languages. We conduct design space exploration and design optimization studies using quantitative and qualitative metrics, and to reduce the high computing times and computational resources intrinsic to these kinds of studies, concurrent simulations and surrogate-based optimization are used.

Studies on the detection of layers with elevated black carbon aerosol (BC) concentrations and the formation conditions of these layers help understand the vertical distribution of BC concentrations, which will provide a basis for the assessment of climate effects and early BC pollution warnings. By using the Weather Research and Forecasting with Chemistry (WRF-Chem) numerical model, we performed a numerical simulation analysis on the authenticity of strong elevated BC concentration layers that were detected by an aircraft in the mixing layer over Harbin, China, which is a high-emission area, on a clear sunny afternoon in the early heating period of 2016. We then discuss possible problems and solutions when non-vertical paths are used to detect the vertical distribution of BC concentrations. Finally, we discuss the favorable conditions for the formation of elevated BC concentration layers by weak vertical flow. The results show that the horizontal variability of BC concentration in the mixing layer in the observation area in Harbin was sufficiently large during the measurement. This produced a false elevated layer, as detected by the aircraft during one round of spiral flight in the mixing layer. The root mean square of the horizontal distribution of BC concentration did not change with height in the mixing layer during the daytime, but it decreased with the thickness of the mixing layer and was higher in the mixing layer than in the free atmosphere. Therefore, the thinner the mixing layer, in which the vertical distribution of the BC concentration is detected in an inclined path, the stronger interference of the horizontal variability on the detected results. When a spiral flight detection path is used, the aircraft should fly at least two rounds in the mixing layer. In the daytime, due to strong turbulence in the mixing layer, weak vertical uplift is not favorable for the occurrence of elevated BC concentration layers in the mixing layer. In the nighttime, if weak vertical uplift is well matched with the BC concentration or its vertical gradient, elevated BC concentration layers can be formed in the atmosphere. Compared with upper layers far from the ground, nighttime elevated layers are easier to form in lower layers near the ground because high BC concentrations or large vertical gradients are more likely to occur in the lower layers. Both cases facilitate the occurrence of large vertical upward transport rates of BC.

This article is devoted to Feller's diffusion equation which arises naturally in probabilities and physics (e.g. wave turbulence theory). If discretized naively, this equation may represent serious numerical difficulties since the diffusion coefficient is practically unbounded and most of its solutions are weakly divergent at the origin. In order to overcome these difficulties we reformulate this equation using some ideas from the Lagrangian fluid mechanics. This allows us to obtain a numerical scheme with a rather generous stability condition. Finally, the algorithm admits an elegant implementation and the corresponding Matlab code is provided with this article under an open source license.

The assimilation of Soil Moisture and Ocean Salinity (SMOS) data into the ECMWF (European Centre for Medium Range Weather Forecasts) H-TESSEL (Hydrology revised - Tiled ECMWF Scheme for Surface Exchanges over Land) model is presented. SMOS soil moisture (SM) estimates have been produced specifically by training a neural network with SMOS brightness temperatures as input and H-TESSEL model SM simulations as reference. This can help the assimilation of SMOS information in several ways: (1) the neural network soil moisture (NNSM) data have a similar climatology to the model, (2) no global bias is present with respect to the model even if regional differences can exist. Experiments performing joint data assimilation (DA) of NNSM, 2 metre air temperature and relative humidity or NNSM-only DA are discussed. The resulting SM was evaluated against a large number of in situ measurements of SM obtaining similar results to those of the model with no assimilation, even if significant differences were found from site to site. In addition, atmospheric forecasts initialized with H-TESSEL runs (without DA) or with the analysed SM were compared to measure of the impact of the satellite information. Although, NNSM DA has an overall neutral impact in the forecast in the Tropics, a significant positive impact was found in other areas and periods, especially in regions with limited in situ information. The joint NNSM, T2m and RH2m DA improves the forecast for all the seasons in the Southern Hemisphere. The impact is mostly due to T2m and RH2m, but SMOS NN DA alone also improves the forecast in July- September. In the Northern Hemisphere, the joint NNSM, T2m and RH2m DA improves the forecast in April-September, while NNSM alone has a significant positive effect in July-September. Furthermore, forecasting skill maps show that SMOS NNSM improves the forecast in North America and in Northern Asia for up to 72 hours lead time.

The Lower Rio Grande Valley, South Texas is considered one of the more vulnerable coastal areas to flooding related with abrupt climate changes. From 1980-2017, there were 7 flooding events, 57 severe storm events, and 8 tropical cyclone events with losses exceeding $1 billion in the State of Texas, according to NOAA NCEI. Coastal flooding is typically a result of storm surge and heavy rainfall produced by hurricanes and tropical storms. In this study, the two-dimensional hydrodynamic flow circulation model is developed to predict the Lower Rio Grande Valley coastal area inundation due to the hurricane storm surge, especially in the case of Hurricane Beulah, 1967. The tropical cyclone properties and tidal constituents were assigned to the updated watershed geographic information with the bottom bathymetric and roughness data. For model validation, the Hurricane Dolly 2008 storm surge due to Hurricane Beulah at the coast and the storm surge reaches up to approximately 40 kilometers west from the coast through a natural river channel. This model can be used for a reliable engineering tool for the coastal hazard emergency management and disaster mitigation.

This article develops duality principles and numerical results for a large class of non-convex variational models. The main results are based on fundamental tools of convex analysis, duality theory and calculus of variations. More specifically the approach is established for a class of non-convex functionals similar as those found in some models in phase transition. Finally, in some sections we present concerning numerical examples and the respective softwares.

A recently published article posited the use of polymer matrix composites (PMCs) as a replacement material for low-carbon steel (LCS) in large power transformer (LPT) tanks [1]. PMCs offer potential advantages such as weight reduction, corrosion prevention, and self-healing of the tank material which may not be achievable with traditional LCS. LCS can arrest ballistic projectiles at relatively low velocities, but at higher velocities, penetration can occur leading to a potential major transformer failure. Numerical simulations of steel projectile impacts upon LCS plates and glass and/or carbon fiber polymer composite laminates showed that with sufficient thickness both could prevent projectile penetration. This prevention was especially efficient when the plates were coated with a high strain rate sensitive material such as polyurea (PU). Our simulations show that the addition of a 3 mm coating of PU to a standard 10 mm thick LCS plate used in LPT tanks could prevent penetration of a 400 m/s steel projectile. For PMC plates, the simulations with the same projectile velocity showed three times faster deceleration with a 3 mm PU coating than without the coating. Thus, two realistic approaches to improving the ballistic protection of LPTs are presented. In addition to their other advantages, this research clearly shows that PMCs with the coating could provide significant ballistic protection for the next generation of LPT tanks.

: In this paper we present an optimization of the planar manufacturing scheme for stretch-free, shape induced metal interconnects to simplify the fabrication with the aim of maximizing the flexibility in the structure regarding to stress and strain. The Formation of trenches between silicon islands are actively used in the lithographic process to create arc shape structures by spin coating resist into the trenches. The resulting resist form is used as a template for the metal lines, which are structured on top. Because this arc shape is beneficial for the flexibility of these bridges. The trench depth as a key parameter for the stress distribution is investigated by applying numerical simulations. The simulated results show that the increase in penetration depth of the metal bridge into the trench increases the tensile load which is converted into a shear Force Q(x), that usually leads to increased strains the structure can generate. For the fabrication the filling of the trenches with resist is optimized by varying the spin speed. Compared to the theoretical resistance, the current-voltage measurements of the metal bridges show a similar behavior and almost every structural variation is capable of functioning as a flexible electrical interconnect in a complete island-bridge array.

Microscale laser dynamic forming, as a novel high-speed microforming technique, can overcome the shortcomings of traditional microforming methods. However, in practical applications, laser dynamic microforming technology is often affected by the rebound behavior of the workpiece surface, limiting the further improvement of processing quality and efficiency. This paper aims to reduce the rebound effect in laser dynamic microforming by using multi-pulse laser shock loading. The forming results of workpieces under different laser energies and laser impact numbers were studied using experimental and numerical simulation methods. Numerical simulations of the forming results after multiple laser shocks were conducted using ANSYS/LS-DYNA software. These numerical simulation results were then experimentally validated and compared. Surface morphology and microstructure of the workpieces were characterized using a confocal microscope and scanning electron microscope, and energy dispersive spectroscopy (EDS) was used to analyze the chemical element content changes in the collision regions at the bottoms of the workpieces after multi-pulse loading, revealing the collision behavior patterns during the forming process. Finally, the forming laws of workpieces under multiple laser shocks were summarized.

The theory says that number interacts with spaces based on the meaning of mathematics, in this way it is possible to obtain numerical knowledge. The theory shows the possibility of using spaces related to each other to efficiently discover whether results and origins are even or odd, but always applying rules to make this work. the study uses equivalent representations of odd and even numbers. Thus, it is possible to discover the possibilities of origins and their results.

Wireline Formation Testing is an important technique in the oil field of exploration and development. Not only it can make real fluid samples of the formation directly obtained to know exactly oil existed in formation or not; but it can also show flowing pressure change to see the production capacity of the formation. So it is important measurement for formation evaluation during the drilling process and supports for activities of the exploration and development in the oil field. A numerical simulation model in this article is researched and established based on the Finite Volume Method with considering the influence of sensitive parameters such as reservoir heterogeneity, probe suction area, and mud-filtrate invasion depth during the drilling. The model is capable to design and evaluate for formation fluid sampling operations with calculating hydrocarbon content and flowing pressure. Furthermore, through case application, the performance and effect in the process of Wireline Formation Testing was demonstrated. The results indicate that this technology can be served as an effective auxiliary tool for fluid sampling operations with the function of optimizing fluid sampling measures. It can improve the accuracy of predicting indicators such as hydrocarbon content and breakthrough time during the sampling process. This study provides important backups and technical guidance for professionals in geological exploration and oilfield development.

A comprehensive modeling framework for the thermoforming of polymer matrix woven laminate composite was developed. Two numerical indicators, the slip path length and traction magnitude, have been identified to be positively correlated to matrix smearing and wrinkling defects. The material model has been calibrated with picture-frame experimental results, and the prediction accuracy for intra-ply shear and thickness distribution were examined with measurements on the physically formed parts. Finally, a parametric study was conducted to determine the relationship between various process parameters and the quality of the formed part. For the trapezoidal part, orienting the laminate at 45-degrees to the mold axis reduces the likelihood of matrix smear and wrinkling defects. Although this laminate orientation yielded a greater spatial variation of part thickness, the thickness deviation is lower than that for the 0-degree orientation case. Higher forming rates were found to result in more defects due to increased slip path lengths and traction magnitudes. Optimal forming speeds should balance rapid shaping within the operating temperature window while avoiding tear. It was discovered that shallower molds benefit from faster ramp rates, while deeper molds require slower rates to manage extensive shearing, stretching, and bending. Faster forming rates lead to smaller thickness increases at high intra-ply shear regions, indicating a shift from intra-ply shear to out-of-plane bending due to the visco-plastic effect of the molten laminate, and can negatively impact part quality. Lastly, it was shown that a well-conceived strategy using darts could improve the part quality by reducing the magnitude of the defect indicators.

The article presents investigations of rail vehicle bogie of Y25 type. The Y25 bogie family is one of the most commonly used freight car bogie designs. In addition to several significant advantages characterising this design, it also has several disadvantages observed since the beginning of more than fifty years of operation in several types of cargo vehicles. One of these defects observed in real systems is "unsatisfactory running stability", particularly at long straight tracks. The article used commercial engineering software VI-Rail to create a model of the gondola car (type 412W Eaos) with two Y25 bogies. The car model was tested empty and loaded (maximum permissible load). Motion along straight and curved tracks with different radii values was analysed. The vehicle velocity was changed from a few m/s to the maximum values for which stable solutions of the model existed. For each route, a non-linear critical velocity was determined, defining the maximum operating velocity of the modelled car. The model solutions were recorded, while just one was selected to present the results - the first wheelset lateral displacement ylw. The opinion about the "imperfect running quality" in curved tracks was confirmed. The possible appearance of self-exciting wheelset vibrations in the modelled car's operating velocity range in the laden state was also observed. The research results on the impact of the bogie suspension parameters change on the vehicle model stability are presented. The crucial parameter in the bogie suspension was indicated. Reducing its value by several percent about the nominal value increases the critical velocity of the car to values higher than the maximum operating velocity of the modelled vehicle.

This study concerns the transport and retention of polydisperse micron-sized (16 ± 6 µm) of microplastics (MPls) in porous media under varying flow rate conditions. Sorption kinetics were modeled using first-order reversible and irreversible kinetic sorption models, with sensitivity analyses providing insights into each sorption parameter's effect. Both numerical modeling and experimental measurements were employed to assess sand filter retention rates. The impact of flow rate on sorption reveals variations in distribution coefficient (Kd), mass transfer coefficient (β), and irreversible sorption rate (K1). Lower flow rates are correlated with higher Kd and β values, indicating an increase in sorption and diminished mass transfer rates. The findings revealed that an increase in Kd resulted in a more gradual sorption process with a decrease in peak concentration, whereas changes in β influenced the rate of sorption and peak concentration to a lesser extent compared to Kd. Lower K1 values are associated with higher peak concentrations and decreased retention efficiency. Retention rates were evaluated by a numerical model and found as 28 ± 1% at a flow rate of 31 ml min⁻¹ and 17 ± 1% at 65 ml min⁻¹. The introduction of MPls into soil environments has been noted to modify transport dynamics into soil. As a result, these alterations effects hydrological characteristics of soil, thereby impacting quality of groundwater and agricultural output. The mean absolute error (MAE) of 6% between modeled and observed retention rates suggests minor discrepancies. This study highlights the importance of examining retention efficiency and the accuracy of numerical models in porous media during MPl transport.

Certain configurations of liquefied natural gas refueling stations exhibit a deficiency in managing boil-off gas. Furthermore, the ill-conceived linkage between the submersible pump and the gas storage tank pipeline leads to impeded natural gas transmission. This study employs Computational Fluid Dynamics (CFD) methodology to scrutinize the hydrodynamic attributes of T-type tee and dovetail tee configurations implemented in the pipeline design connecting the submersible pump and storage tank in an LNG filling station across diverse operational scenarios. The T-type tee induces detachment of the primary flow from the inner wall due to inertial forces, resulting in vortex formation and heightened resistance, accompanied by increased energy dissipation. Conversely, the dovetail tee, with its circular wall transition, mitigates vortex generation, reducing the separation zone and consequently minimizing resistance and energy loss. The maximum static differential pressure between the inlet and outlet of the dovetail tee is diminished by 52.52% when compared to that of the T-type tee. In the most noteworthy scenarios, the local resistance coefficient of the dovetail tee is even less than 1/10 of that of the T-type tee. In practical engineering applications, the incorporation of dovetail tees leads to a 17.58% reduction in the required elevation difference. This results in a more uniform flow field and enhanced stability in both flow rate and pressure. Such improvements contribute to heightened engineering efficiency and environmental sustainability, particularly evident in the design of LNG filling stations.

Nuclear fusion reactors are composed by several complex components whose behaviour may be not certain a priori. This uncertainty may have a significant importance in the evolution of fault transients in the machine, causing unexpected damages to its components. For this reason a suitable method for the uncertainty propagation during those transient is required. The Monte Carlo method would be the reference option, but it is, in most of the cases, not applicable due to the large amount of required simulations to be repeated. In this context the Polynomial Chaos Expansion has been considered as a valuable alternative. It allows to create a surrogate model of the original one in terms of orthogonal polynomials. Then, the uncertainty quantification is performed repeatedly calling this much simpler and faster model. Using the fast current discharge in the Divertor Tokamak Test Toroidal Field (DTT TF) coils as a reference scenario, this method has been applied: the uncertainty on the parameters of the Fast Discharge Unit (FDU) varistor disks is propagated to the simulated electrical and electro-magnetic relevant effects. Eventually two worst case scenarios have been analyzed from the thermal-hydraulic point of view with the 4C code, simulating a fast current discharge as a consequence of a coil quench. Eventually it has been demonstrated that the uncertainty on the inputs (varistor parameters) strongly propagates obtaining a wide range of possible scenarios in case of accidental transients. This result underlines the necessity to take into account and propagate all possible uncertainties in the design of a fusion reactor, according to the Best Estimate Plus Uncertainty approach.

The transportation of feed pellets via pneumatic conveying plays an improtant role in feed industry. In recent years, many efforts are made both exprimentally and numerically to gain a better understanding of the underlying mechanism for pneumatic conveying. Though few of those research is directly related to feed pellets, it can be beneficial to draw a full picture of rencent development in pneumatic conveying, with emphasis on aspects extendable to feed transportation. This paper reviews first the major factors concerning feed pellets pneumatic conveying, such as particle breakage, pipe wear and electrostatic. Building on that, new advancement including emerging new technologies in experiments and simulations are discussed, with a focus on the experimental measurements and mathematical models, repectively. The needs for future research and the analogy to feed pellets tranportation is given lastly.

The fatigue delamination damage is one of the most important fatigue failure modes of laminated composite structures. However, the developments of the theoretical framework, mathematical/physical model and numerical simulation of fatigue delamination are still challenging issues, and there is a lack of systematic classification. This article reviews the experimental phenomena of the onset and propagation stage of delamination under fatigue loading, and summarizes the commonly used phenomenological models for laminated composite structures. The research methods, general modeling formulas and development prospects of the phenomenological models are presented in detail. In the light of the analysis of finite element model (FEM) for the laminated composite structures, a number of simulation methods of fatigue delamination crack propagation damage model are carefully classified. Furthermore, within the theoretical framework of strength theory model (SM), fracture mechanics model (FM), damage mechanics model (DM) and hybrid model (HM), the complete procedure, application, capability assessment, advantages and limitations of the models are also discussed in detail. Finally, several valuable suggestions are given for the research interests, and challenging technical problems that need to be overcome on the fatigue delamination prediction of laminated composite structures in the future.

In this study, three new demountable joints consisting of reinforced concrete columns and steel beams were proposed and their seismic performance was investigated using cyclic loading tests. The test results demonstrated that the three demountable RCS joints had good seismic performance. Using the finite element software ABAQUS, the influence of parameters such as beam flange thickness, bolt strength, and connector steel strength on the seismic performance of each joint was analyzed, and the influence of different parameters on the seismic behavior of the joint was determined. The results also showed that the three demountable RCS joints were sensitive to changes in the thickness of the steel beam flange, while the connector steel strength and bolt type had little impact on the joint's capacity. Additionally, shear capacity calculation formulas for the joint core area provided by different codes and researchers were compared with test and finite element results. The results showed that the calculation results of the ASCE guidance method, the Nishiyama method, and the CECS 347-2013 method were higher than the test values, while the calculation results of the Para method were lower because it did not consider the contribution of the cylindrical steel plate to the shear capacity of the joint core area.

Pore fluid pressure is very important to the generation, migration and accumulation of petroleum. The previous studies indicate that the Chezhen sag region is typically characterized by pore fluid overpressure (the difference between pore fluid pressure and hydrostatic pressure). To date, the formation mechanism of pore overpressure and the accumulation regularity of “upper source-lower reservoir” type in this region remains unknown. In order to investigate these problems, a 2-D finite element model is established with regards to the fluid-solid coupling in Chegu 25 block of Chezhen depression, fully considering the existing seismic, logging data and regional tectonic stress environment. Meanwhile, we calculate the abnormal overpressure generated at the source rock during hydrocarbon generation and the process of hydrocarbon migration and accumulation along the faults, analyzing the dynamic conditions of hydrocarbon downward accumulation. The results show that overpressure can accelerate migration of hydrocarbon and improve the efficiency of hydrocarbon accumulation. However, when the overpressure is too large, tensile fractures and shear fractures may occur, resulting in hydrocarbon dissipation, and changing the results of oil and gas accumulation. The overpressure at the source rock is mainly caused by hydrocarbon generation, while the overpressure at the reservoir is primarily created by unbalanced compaction. As the dominant channel of hydrocarbon migration, overpressure will change the direction and path of hydrocarbon migration in the fault. Therefore, the “upper source-lower reservoir” hydrocarbon accumulation model is strongly explained by the high permeability of faults and the presence overpressure. In summary, the simulated overpressure results are in good agreement with the mud weight equivalent overpressure and the drill stem tests (DSTs).

In the construction of shield crossing existing mined tunnel without load, it is imperative to develop corresponding design standards that reflect actual engineering force characteristics to ensure the successful completion of tunnel construction. This research uses The MIDAS-GTS finite element software to facilitate the creation of a numerical model of the shield structure for an air-push-over mine tunnel project in Changsha, China, investigating the stress field’s evolution during shield construction, and calculating the maximum positive and negative bending moments and maximum axial forces for different structures and other force states under various construction conditions. This study's findings informed the design and construction optimisation of the shield tunnelling empty-push method. The outcomes of this numerical simulation led to several key findings: (1) The soil density exerted a significantly greater impact on the internal forces of the initial support structure than both the tunnel depth and soil Poisson's ratio. Additionally, a sudden shift in internal forces occurred within the 300-350 mm range when the lining thickness was altered. (2) Factors such as the tunnel depth, soil density, soil Poisson's ratio μ, and lining thickness have a similarly influenced internal forces of the segment and the initial support. Notably, the backfill layer thickness significantly affected the segment’s maximum axial force causing an abrupt change of approximately 300 mm. (3) Under the shield machine equipment’s weight constraint, it is essential to control the guide rail’s thickness, to prevent it from becoming overly large.

Large aluminum alloy ring forgings are the core components of heavy-duty rocket fuel storage tanks, and the large residual stress inside the rings leads to poor shape accuracy of large thin-walled parts. The initial stress of the 2219 aluminum alloy ring blank was tested using the drilling method, and the creep constitutive coefficient of the 2219 aluminum alloy was determined through stress relaxation tests. The numerical simulation processes of thermal stress relief (TSR), vibration stress relief (VSR), and thermal-vibration stress relief (TVSR) were compared and established. Through the correlation analysis between the actual measurement results of residual stress and the simulation results, it can be seen that the strong correlation in three directions at each measurement point accounts for over 37.5%, and the moderate correlation accounts for over 62.5%. This indicates that the numerical simulation model of 2219 aluminum alloy ring containing initial residual stress can accurately reflect the size and distribution of residual stress inside the actual ring. The simulation results show that the derived constitutive model can describe the stress relaxation process of TVSR by combining a single thermal time effect stress relaxation constitutive theory with a VSR plastic deformation material model. The simulation models established above were used to calculate the residual stress homogenization ability of three types of aging. The results showed that VSR, TSR, and TVSR can homogenize and reduce the residual stress field inside the ring, improve the distribution of residual stress inside the ring, and have a better overall homogenization ability of TVSR. The VSR control has a certain effect on reducing and homogenizing residual stress, but compared with TSR and TVSR, the reduction and homogenization ability of residual stress control is limited. The homogenization control effect TVSR>TSR>VSR, and the maximum equivalent stress homogenization rates of VSR, TSR, and TVSR are 52.8%, 80.6%, and 82.2%, respectively. Then, numerical simulation technology is used to study how the initial residual stress in the blank will cause the deformation of the ring during the thin-walled machining process. The roundness error theory of the minimum containment area method is applied to evaluate the deformation degree during the thin-walled numerical machining process, and the TVSR method is used for stress regulation. The deformation law of the thin-walled machining of the ring under different aging parameters is studied.

The main objective of this study is to find out the influence of cooperation and intra-specific competition in escaping predation through refuge of the prey population and the effect of the two intra-specific interactions on the dynamics of prey-predator systems. For this purposes, two mathematical models with Holling type-II functional response function have been proposed and analyzed. The first model includes cooperation among prey populations whereas the second one incorporates intra-specific competition. Existence conditions and stability of different equilibrium points of both models have been carried out for the qualitative behaviour of the systems. Refuge through intra-specific competition has a stabilizing role, whereas cooperation has a destabilizing role on the system dynamics. Periodic oscillations are observed in both the systems through Hopf bifurcation. From the analytical and numerical findings, we conclude that intra-specific competition affects the prey population and continuously checks the refuge class under a critical value, and thus it never becomes too large to cause predator extinction due to food scarcity. Conversely, cooperation leads maximum individuals to escape predation through the refuge so that predators will suffer from low predation success.

On the basis of the force and safety factor analysis of traditional retaining wall, a new analytical method of force and displacement of slope is suggested, the numerical theoretical solution of the stress distribution of the sliding body can be obtained under the conditions, which the stresses distribution are satisfied with the differential equilibrium equations, the boundary conditions, the compatibility equation and the macroscopic equilibrium equations. The interface stresses between the sliding body and the retaining wall are continuous, the theoretical solution of retaining wall stress distributions can be gotten, while the stress differential equilibrium equation, the compatibility equation, macroscopic force and moment balance equations are satisfied. The strain and displacement solutions can be obtained by using Duncan Chang and Hooke constitutive equations for the slope and the retaining wall respectively. The transfer station of landfill in the Guandukou Town of Badong County is taken as an example, the results of the sliding body and retaining wall analysis show: The stress and strain solutions of a slope and a retaining wall can be obtained by the proposed method, the forces between the retaining wall and the sliding body include shear stress and normal stress, and the stress distributions change with the deformation of the sliding body, the shape and material of retaining wall can be optimized according to the calculation results，it is feasible for the proposed analysis method of slope with retaining wall design to be run many years.

In this paper, the research progress on dynamic behaviors of RC structural members is reviewed from experimental, theoretical and numerical perspectives. Firstly, the basic overview, measurement methods, main conclusions and current limitations of available dynamic loading tests are presented. Then the theoretical studies on the dynamic constitutive models of RC materials, the dynamic increase factor (DIF) model for concrete and reinforcing steel and the proposed modified models of dynamic behavior parameter at the structural member level are summarized. Finally, the available modelling approach and the method for incorporating the dynamic effect in numerical simulation of RC structures are reviewed. Moreover, a brief introduction is made to the dynamic hysteretic model established on the experimental data, which provides an alternative approach to consider the dynamic effect beside the commonly used DIF method. This paper provides valuable reference for experimental studies and numerical simulations on the dynamic behaviors of RC structures, and also puts forward some issues that need to be solved in the future research works..

This study employs a high-fidelity numerical framework to determine the plastic material flow patterns and temperature distributions that lead to void formation during friction stir welding (FSW), and to relate the void morphologies to the underlying alloy material properties and process conditions. Three aluminum alloys, viz., 6061-T6, 7075-T6, and 5053-H18 were investigated under varying traverse speeds. The choice of aluminum alloys enables investigation of a wide range of thermal and mechanical properties. The numerical simulations were validated using experimental observations of void morphologies in these three alloys. Temperatures, plastic strain rates, and material flow patterns are considered. The key results from this study are: (1) The predicted stir zone and void morphology are in good agreement with the experimental observations, (2) The temperature and plastic strain-rate maps in the steady-state process conditions show a strong dependency on the alloy type and traverse speeds, (3) The material velocity contours provide a good insight into the material flow in the stir zone for the FSW process conditions that result in voids as well as those that do not result in voids. The numerical model and the ensuing parametric studies presented in this work provide a framework for understanding material flow under different process conditions in aluminum alloys, and potentially in other alloys. Furthermore, the utility of the numerical model for making quantitative predictions and investigating different process parameters to reduce void formation is demonstrated.

The dynamic development of electromobility poses challenges to designers regarding not only the efficiency of energy transformation but also the battery life, which is influenced by the stability of its operating temperature. Designing cooling systems is connected not only with the optimization of energy management but also with other environmental parameters, such as noise emission. The paper presents the numerical optimization of an innovative radiator for use in electric buses in terms of energy consumption and noise emission. The results of the numerical studies were verified in laboratory and field conditions, showing a very good convergence of the model with the results of the experiments.