Gas hydrate provinces are present in at least in two areas along Brazil’s continental margin: (1) the Rio Grande Cone in the southeast, and (2) the Amazon deep-sea fan in the equatorial region. The occurrence of gas hydrates in these depocentres was first detected geophysically and has recently been proven by seafloor sampling of gas vents, detected as water column acoustic anomalies rising from seafloor depressions (pockmarks) and/or mounds, many associated with seafloor faults. The gas vents include typical features of cold seep systems, including shallow sulphate reduction depths (<4 m), authigenic carbonate pavements and chemosynthetic ecosystems. In both areas, gas sampled in hydrate and in sediments is dominantly formed by biogenic methane. Calculation of the methane hydrate stability zone for water temperatures in the two areas shows that gas vents occur along its feather edge (water depths between 510-760 m in the Rio Grande Cone and 500-670 m in the Amazon deep-sea fan) but also in deeper waters within the stability zone. Gas venting along the feather edge of the stability zone could reflect gas hydrate dissociation and release to the oceans, as inferred on other continental margins, or upward fluid flow through the stability zone facilitated by tectonic structures recording the gravitational collapse of both depocentres. The potential quantity of venting gas on the Brazilian margin under different scenarios of natural or anthropogenic change require further investigation. The studied areas provide a natural laboratory where these critical processes can be analysed and quantified.

The present study focuses on the development and optimization of a highly efficient unique hybrid technique — membrane-assisted gas absorption (MAGA) in designing the separation unit, which provides the improvement in mass-transfer of a target component during the natural gas processing in terms of sweetening stage. A novel design of membrane-assisted gas absorption cell is used to enhance the ratio between absorbent amount and membrane surface available for permeation. The performance tests were implemented on example of two gas mixtures separation: one is model ternary gas mixture and the second is quasi real natural gas, which includes number of hydrocarbons, nitrogen, acid impurities and xenon. For both cases, the MAGA unit demonstrated high acid gases removal efficiency, and high recovery of hydrocarbons. The ultimate efficiency of studied system was up to 96 and 61 % of removed acid gases with hydrocarbons losses up to 1 % at highest productivity. In this way, the residual sum of acid gases content may be lowered to 1 vol.% using the heat-free hybrid membrane-assisted gas absorption unit maintaining suitable recovery rate of methane, ethane, propane and n-butane. Nevertheless, the overall efficiency of the process may be enhanced using the specific absorption agents with aqueous amino alcohol solutions.

Recent studies have reported shallow and deep seep areas offshore Mocha island. Gas hydrate occurrences along the Chilean margin could explain seeps presence. Gas phases (gas hydrate and free gas) and geothermal gradients were estimated analysing two seismic sections. Close to Mocha island (up to 20 km) were detected high (up to 1900 m/s) and low (1260 m/s) velocities associated with high gas hydrate (up to 20 % of total volume) and free gas (up to 1.1% of total volume) concentrations respectively. These values are in agreement with a variable and high geothermal gradient (65 to 110 °C/km) related to high supply deep fluids canalised by faults and fractures. Faraway from Mocha island (more than 60 km), free gas concentrations decrease to 0.3 % of total volume and low geothermal gradient (from 35 to 60 °C/km) are associated with low fluids supply. Finally, we propose gas hydrate dissociation processes as the main supply source for seeps in the vicinity of Mocha island. These processes can be triggered by ancient sliding reported in literature.

Here we propose a simple way in which one can considerably improve performance of the gas stripper setup at the GSI UNILAC. To do so, it will be enough to replace inside the main GSI stripper chamber the present nozzle and the short windowless storage gas cell (for pulsed gas-jet operation mode) by a simple conical diverging nozzle combined with a gas catcher tube placed on the axis of gas-jet at some distance downstream the nozzle exit. As a result, the background pressure in the main and differentially pumped adjacent vacuum chambers of the gas stripper at the GSI UNILAC will dramatically reduce, and it will make possible to achieve the required optimal thickness of gas targets. The pulsed gas stripper operation is simply realized by implementing a commercially available fast gas valve connected to the nozzle entrance. Moreover, the ion beam pulses repetition rate can be increased and it will allow for the considerably higher average intensity of the ion beams extracted from the GSI UNILAC. Performance of the proposed GSI UNILAC gas stripper modification we explored by means of detailed computer experiments, which give a realistic description of supersonic gas jets flowing out the nozzle into vacuum. Results of these computer experiments have presented and discussed.

ABSTRACT In the quest for decarbonisation, it's essential for different sectors of the economy to collaborate and invest significantly. This study presents an innovative approach that merges technological insight with philosophical considerations at a national scale, with the intention of shaping national policy and practice. The aim of this research is to assist in formulating decarbonisation strategies for intricate economies. Libya, a major oil exporter aiming to diversify its energy revenue sources, is used as the case study, although the principles can be applied to create decarbonisation strategies across the globe. The decarbonisation framework evaluated in this study encompasses wind based renewable electricity, hydrogen, and gas turbine combined cycles. A comprehensive set of both official and unofficial national data was assembled, integrated and analysed to conduct this study. The developed analytical model considers a variety of factors including consumption in different sectors, geographical data, weather patterns, wind potential, and consumption trends, amongst others. Even when gaps and inconsistencies were encountered, reasonable assumptions and projections were used to fill these. This model is seen as a valuable foundation for developing replacement scenarios that can realistically guide production and user engagement towards decarbonisation. The aim of this model is to maintain the advantages of the current energy consumption, assuming a 2% growth rate, and to assess changes in energy consumption in a fully green economy. While some level of speculation is present in the results, important qualitative and quantitative insights emerge, with the key takeaway being the use of hydrogen and the anticipated considerable increase in electricity demand. Two scenarios were evaluated: achieving energy self-sufficiency and replacing current oil exports with hydrogen exports on an energy content basis. This study offers, for the first time, a quantitative perspective on the wind-based infrastructure needs resulting from the evaluation of the two scenarios. In the first scenario, energy requirements were based on replacing fossil fuels with renewable sources. In contrast, the second scenario included maintaining energy exports at levels like the past, substituting oil with hydrogen. The findings clearly demonstrate that this transition will demand vast changes and substantial investments. The primary requirements identified are 14876 or 24532 square kilometres (for self-sufficiency and exports), and 47 single-shaft 600 MW combined-cycle gas turbines. This foundational analysis could represent the commencement of the research, investment, and political agenda on the journey to decarbonisation.

This report aimed to know the performance of local mineral-based composite ceramic. The materials used consist of Indonesian local minerals, which are jarosite and manganite minerals as sources of oxide iron and Mangan. The materials were synthesized using the precipitation method, whereas composite ceramic was fabricated using a screen printing method and fired at 600 oC using a furnace. The results of the characterizations indicate that the sample forms three phases on diffraction peaks. The differences in the resistance values in ambient and ethanol environments indicate that the sample has very different responses. The high porosity of the sample greatly support the gas adsorption process. Thus, the sample has a high level of sensitivity. With the above characteristics, the composite ceramic which was fabricated has the potential to be applied to gas sensors, especially ethanol gas sensors.

The fluorine-less noble-gas containing anions OBONgO- and OCNNgO-have been studied by correlated electronic structure calculation and density functional theory. The obtained energetics indicates that for Ng = Kr and Xe, these anions should be kinetically stable at low temperature. The molecular structures and electron density distribution suggests that these anions are stabilized by ion-induced dipole interactions with charges concentrated on the electronegative OBO and OCN groups. The current study shows that in additional to the fluoride ion, polyatomic groups with strong electronic affinities can also form stable noble-gas containing anions of the type X-...NgO.

Residual gas in exetainer vials leads to nitrous oxide (N2O) gas underestimation. This study compared four evacuation methods such as gas exchange by displacement (GED), evacuation with a vacuum pump (VP), evacuation with a syringe (VS) and pre-evacuated Exetainer (PEE) to assess the residual gas effect on gas sample concentration. PEE and VP methods showed superior performance, displaying lower deviations from actual gas concentrations with RMSE values of 0.239 and 0.179, respectively, at 12.5 ppm standard gas levels. Conversely, GED and VS methods exhibited higher deviations with RMSE values of 0.740 and 0.448, respectively, at 12.5 ppm. Errors were more pronounced at lower gas concentrations. To address residual gas effects in GED and VS methods, standard gases were stored for calibration in evacuated vials (EVM) matching the sample collection method, rather than in syringes (SM). This EVM approach enhanced precision by 14.43% and 6.24% for GED and VS methods, respectively, at 0.781 ppm standard gas levels. The study concludes that PEE and VP methods are more reliable for vial evacuation. Using vials prepared using the same method as sample collection vials can mitigate residual gas effects effectively. This study holds substantial importance in enhancing the accurate measurement of greenhouse gas emissions, particularly focusing on nitrous oxide.

Numerous reservoirs that play a significant role in worldwide petroleum production and reserves contain fractures. Typically, the fractures must form a connected network for a reservoir to be classified as naturally fractured. Characterizing the reservoir with a focus on its fracture network is crucial for modeling and predicting production performance. To simplify the solution, dual continuum modeling techniques are commonly employed. However, to use continuum-scale approaches, properties such as average aperture, permeability, and matrix fracture interaction parameters must be assigned, making it necessary to improve fracture depiction and modeling methods. This study investigates a fractured reservoir with a low matrix permeability and a well-connected fracture network. The focus is on the impact of the hyrachical fracture network on the production performance of gas-based enhanced oil recovery methods. The Discrete Fracture Model (DFN) was utilized to create comprehensive two-dimensional models for three processes: Gas Injection (GI), Water Alternating Gas (WAG), and Foam Assisted Water Alternating Gas (FAWAG). Moreover, dimensionless numbers were employed to establish connections between properties across the entire fracture hierarchy, spanning from minor to major fractures and encompassing the fracture intensity. The results indicate that the FAWAG is more sensitive to fracture types and networks than the WAG and GI processes. Hence, the sensitivity of the individual EOR method to the fracture network requires a respective depth of description of the fracture network. However, other factors, such as reservoir fluids properties and fracture properties, might influence the recovery when the minor fracture networks are excluded. This study has determined that, among the enhanced oil recovery (EOR) techniques examined, the significance of the hyrachical depth of fracture networks diminishes as the ratio of major (primary fracture) aperture to the aperture of medium and minor fractures increases. Additionally, the impact of the assisted-gravity drainage method was greater with increased reservoir height; however, as the intensity ratio increased, the relative importance of medium and minor fracture networks decreased.

Various cultivars of citrus fruits have unique construction, such as thick outer skin. These constructions generate gas diffusion resistance between atmosphere and fruit, which can limit a gas exchange of O2 and CO2. However, it has not been sufficiently investigated. In this study on 7 cultivars of citrus fruit, it was aimed firstly to investigate a gas diffusion resistance utilizing ethane efflux method and secondly to investigate internal gas concentration of O2 and CO2. As a result, a cultivar of citrus fruit with slimer outer skin thickness had lower resistance. For the internal gas, a high CO2 concentration in comparison with the atmosphere was observed even in the fruits with the minimum resistance, which no considerable difference among all cultivars was observed in regardless of gas diffusion resistance value. However, when the fruits stored at 25 °C for 2 weeks, it was tended to increase CO2 gas concentration and decrease O2 gas concentration with increase in the resistance value. Therefore, when respiration of citrus fruits is activated at ambient temperature, self-control system of internal gas concentration can be driven to suppress their respiration, which was induced by gas diffusion resistance generated from their construction.

Cancer remains a leading cause of death despite advancements in research and treatment, with traditional therapies often causing significant side effects and resistance. Oxyhydrogen gas, a mixture of 66% molecular hydrogen (H₂) and 33% molecular oxygen (O₂) has shown exceptional promise as a novel therapeutic agent due to its ability to modulate oxidative stress, inflammation, and apoptosis. H2, a key component of oxy-hydrogen gas, neutralises reactive oxygen and nitrogen species, enhancing existing treatments and reducing harmful oxidative states in cancer cells. H₂ also lowers pro-inflammatory mediators including chemokines, cytokines and interleukins, inhibiting cancer cell proliferation and boosting the effectiveness of conventional therapies. Additionally, hydrogen can induce apoptosis in cancer cells by modulating pathways such as MAPK and inhibiting the PI3K/Akt phosphorylation cascade. Preclinical and clinical evidence supports oxyhydrogen gas's potential in treating various cancers. In lung cancer models, it inhibits cell proliferation, induces apoptosis, and enhances chemotherapy sensitivity. Similar results have been observed in breast cancer, where patients reported improved quality of life. In colorectal cancer, oxyhydrogen gas suppresses tumour growth, induces apoptosis and improves intestinal microflora dysbiosis. The unique properties of oxyhydrogen gas make it a promising adjunctive or standalone cancer treatment. However, further research is needed to understand H₂'s mechanisms, optimise treatment protocols, and evaluate long-term safety and efficacy in human patients.

In this paper, we describe the surface modification of Polytetrafluoroethylene (PTFE) through plasma treatment process. Several parameters including different active gases; RF power; dis-tance between the plasma source and sample; and plasma duration were optimized to reduce the hydrophobic nature of PTFE. Three different active gases were used [i.e., N2, O2 and (Ar+H2)], in which N2 was effective to reduce the hydrophobicity of PTFE within shorter plasma duration of 2 minutes. Several surface characterizations including ATR-FTIR, water contact angle, FE-SEM and XPS were utilized to verify the neat and modified PTFE surface after plasma treatment. The plasma treatment using N2 as an active gas improved the wettability of PTFE membrane, show-ing a water contact angle of 108° when compared with the neat PTFE (140°). The SEM images of plasma treated PTFE shows greater modifications on the surface indicating non-uniform fiber alignment and torn fibers at several places. The obtained results confirm the fact that plasma treatment is an effective way to modify the PTFE surface without altering its bulk property.

During the extraction of hard coal in Polish conditions, methane is emitted, which is referred to as mine gas. As a result of the desorption of methane, a greenhouse gas is released from coal seams. In order to reduce atmospheric emissions, methane from coal seams is captured by a methane drainage system. On the other hand, methane, which has been separated into underground mining excavations, is discharged into the atmosphere with a stream of ventilation air. For many years, Polish hard coal mines have been capturing methane to ensure the safety of the crew and the continuity of mining operations. As a greenhouse gas, methane has a significant potential, as it is more effective at absorbing and re-emitting radiation than carbon dioxide. The increase in the amount of methane in the atmosphere is a significant factor influencing global warming, however, it is not as strong as the increase in carbon dioxide. Therefore, in Polish mines, the methane-air mixture captured in the methane drainage system is not emitted to the atmosphere, but burned as fuel in systems, including cogeneration systems, to generate electricity, heat and cold. However, in order for such use to be possible, the methane-air mixture must meet appropriate quality and quantity requirements. The article presents an analysis of changes in selected parameters of the captured methane-air mixture from one of the hard coal mines in the Upper Silesian Coal Basin in Poland. The paper analyses the changes in concentration and size of the captured methane stream through the methane capturing system. The gas captured by the methane drainage system, as an energy source, can be used in cogeneration, when the methane concentration is greater than 40%. Considering the variability of CH4 concentration in the captured mixture, it was also indicated which pure methane stream must be added to the gas mixture in order for this gas to be used as a fuel for gas engines. The balance of power of produced electric energy in gas engines is presented. Possible solutions ensuring constant concentration of the captured methane-air mixture are also presented.

This research paper presents a new application of electroactive polyimide doped with gold nanoparticles (PI/AuNPs) as a chemiresistor sensor for detecting hydrogen sulfide gas. The synthesis of PI/AuNPs was done in a simple 3-step process of polymerization using the as prepared amine-capped aniline trimer (ACAT), followed by imidization, and doping. Spectral analyses via FTIR, LC-MS and ¹H-NMR confirmed the formation of amine-capped aniline trimer with a MW of 288 g mol^-1. Comparison of ACAT, BSAA, and PI FTIR spectra showed successful polymerization of the last, while XRD validated the incorporation of metal nanoparticles onto the polymer matrix showing characteristic diffraction peaks corresponding to gold. Furthermore, TEM, and FE-SEM revealed the presence of well-dispersed Au nanoparticles with an average diameter of about 60nm. The electroactive PI/AuNPs-based sensor showed a sensitivity of 0.29% ppm^-1 H₂S at a linear concentration range of 50 to 300 ppm H₂S (r = 0.9777). The theoretical limit of detection was found at 0.142 ppm or 142 ppb H₂S gas. The sensor provided a stable response reading at an average response time of 43±5 seconds, which was easily recovered after an average time of 99±5 seconds. The sensor response was highly repeatable and reversible with RSD values of 8.88%, and 8.60%, respectively. Compared with the performance of the conventional conducting polyaniline also doped with gold nanoparticles (PANI/AuNPs), the fabricated electroactive PI/AuNPs exhibited improved sensing performance making it a potential candidate in monitoring H₂S in the environment and for work-related safety.

Shale gas content is the key parameter for shale gas potential evaluation and favorable area prediction. Therefore, it is very important to determine shale gas content accurately. Generally, we use the USBM method for coal reservoirs to calculate gas content of shale reservoirs. However, shale reservoirs are different from coal reservoirs in depth, pressure, core collection, etc. This method would inevitably cause problems. In order to make the USBM method more suitable for shale reservoir, an improved USBM method is put forward on the basis of systematic analysis of core pressure history and temperature history during shale gas desorption. The improved USBM method modifies the calculation method of the lost time, and determines the temperature balance time of water heating. In addition, we give the calculation method of adsorption gas content and free gas content, especially the new method of calculating the oil dissolved gas content and water dissolved gas content which are easily neglected. We used the direct method (USBM and the improved USBM) and the indirect method (adsorption gas, free gas and dissolved gas) to calculate the shale gas content of 16 shale samples of the Triassic Yanchang Formation in the Southeastern Ordos Basin, China. The results of the improved USBM method show that the total shale gas content is high, with an average of 3.97 m³/t, and the lost shale gas content is the largest proportion with an average of 62%. The total shale gas content calculated by the improved USBM method is greater than that of the USBM method. The results of the indirect method show that the total shale gas content is large, with an average of 4.11 m³/t, and the adsorption shale gas content is the largest proportion with an average of 71%. The oil dissolved shale gas content which should be taken attention accounts for about 7.8%. The relative error between the improved USBM method and indirect method is much smaller than that between USBM method and indirect method, which verifies the accuracy of the improved USBM method.

Gas flaring is a disposal process widely used in the oil extraction and processing industry. It consists in the burning of unwanted gas at the tip of a stack and due to its thermal characteristic and the thermal emission it is possible to observe and to quantify it from space. Spaceborne observations allows us to collect information across regions and hence to provide a base for estimation of emissions on global scale. We have successfully adapted the Visible Infrared Imaging Radiometer Suite (VIIRS) Nightfire algorithm for the detection and characterisation of persistent hot spots, including gas flares, to the Sea and Land Surface Temperature Radiometer (SLSTR) observations on-board the Sentinel- satellites. A hot event at temperatures typical of a gas flare will produce a local maximum in the night-time readings of the shortwave and mid-infrared (SWIR and MIR) channels of SLSTR. The SWIR band centered at 1.61 mmis closest to the expected spectral radiancemaximumand serves as the primary detection band. The hot source is characterised in terms of temperature and area by fitting the sum of two Planck curves, one for the hot source and another for the background, to the radiances from all the available SWIR, MIR and thermal infra-red channels of SLSTR. The flaring radiative power is calculated from the gas flare temperature and area. Our algorithm differs from the original VIIRS Nightfire algorithm in three key aspects: (1) It uses a granule-based contextual thresholding to detect hot pixels, being independent of the number of hot sources present and their intensity. (2) It analyses entire clusters of hot source detections instead of individual pixels. This is arguably a more comprehensive use of the available information. (3) The co-registration errors between hot source clusters in the different spectral bands are calculated and corrected. This also contributes to the SLSTR instrument validation. Cross-comparisons of the new gas flare characterisation with temporally close observations by the higher resolution German FireBIRD TET-1 small satellite and with the Nightfire product based on VIIRS on-board the Suomi-NPP satellite show general agreement for an individual flaring site in Siberia and for several flaring regions around the world. Small systematic differences to VIIRS Nightfire are nevertheless apparent. Based on the hot spot characterisation, gas flares can be identified and flared gas volumes and pollutant emissions can be calculated with previously published methods.

Greenhouse gases (GHGs) trap heat in the atmosphere, causing the Earth's surface temperature to rise. The main GHGs are carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), perfluorocarbons (PFCs), hydrofluorocarbons (HFCs), and sulfur hexafluoride (SF6). Human activities are increasing GHG concentrations rapidly, which is causing global climate change. Global climate change is increasing environmental and public health problems. To reduce greenhouse gas (GHG) emissions, identify where the emissions are coming from, develop a plan to reduce them, and then implement and monitor the plan to ensure that emissions are actually reduced. Anthropogenic global climate change has large and increasingly adverse economic effects. Cities emit the most GHGs due to fossil fuel burning and power usage. The four major GHG emitters are energy, transportation, waste management, and urban land use sectors. Organizations should prepare action plans to lower their GHG emissions and stop the worst consequences of climate change. These action plans require companies and local authorities to submit their GHG emissions reports on a yearly basis. A GHG emissions management system includes several processes and tools created by organizations to understand, measure, monitor, report, and validate their GHG emissions. Two of the most widely adapted frameworks for GHG inventory reporting are ISO 14064 and the GHG Protocol. This review paper aims to identify some of the key points of GHG inventory preparation and mitigation strategies.

The presence of high concentrations of flammable gases and volatile organic compounds in the atmosphere has been widely reported to be detrimental to human survival. A lot of research effort has been put towards finding an efficient means of quick detection of these gases below their ‘immediately dangerous to life or health’ concentrations. Detecting these gases in an oxygen-deficient environment is a crucial task to consider and has been overlooked. In this research, double substitution spinel with chemical formula Co1-2xNixMnxFe2-yCeyO4, where 0 ≤ x = y ≤ 0.3, were prepared via the glycol-thermal technique. The final products following the appropriate substitution are CoFe2O4 (dried naturally), CoFe2O4 (dried with Infrared lamp), Co0.8Ni0.1Mn0.1Fe1.9Ce0.1O4, Co0.6Ni0.2Mn0.2Fe1.8Ce0.2O4, and Co0.4Ni0.3Mn0.3Fe1.7Ce0.3O4 spinel ferrites. The X-ray diffractometry (XRD), High resolution transmission electron micrographs (HRTEM), and X-ray photoelectron spectroscopy (XPS) of the samples confirm the formation of the spinel. The gas sensing performance of this samples were tested at operating temperature of 225 ºC towards liquefied petroleum gas (LPG), ammonia, ethanol, and propanol. The Co0.8Ni0.1Mn0.1Fe1.9Ce0.1O4-based sensor was selective to LPG, with a high response of 116.43 toward 6 000 ppm of LPG when helium was used as carrier gas, 3.35 when dry-air was the carrier gas, 4.4 when nitrogen was the carrier gas, but was not sensitive when argon was used as a carrier gas.

In this paper a new double-nozzle technique for in-gas-jet laser resonance ionization spectroscopy is proposed. The functionality of this new technique we explored by detailed gas dynamic and Monte Carlo atom-trajectory simulations, which results are presented and discussed. The results of similar computer simulations for JetRIS setup (as a typical representative of the conventional nowadays in-gas-jet technique) are presented and discussed as well. The direct comparison of calculation results for proposed new technique with the conventional one shows that the double-nozzle technique has many advantages compared with that one used in the JetRIS setup at GSI for future high-resolution laser spectroscopic study of heaviest elements. To fully implement the proposed new technique to all existing (or under construction) setups for in-gas-jet laser resonance ionization spectroscopy, it will be enough just replace the used their supersonic nozzle by the miniature double-nozzle device described in the paper.

Natural gas is an important energy source among various fossil fuels. However, natural gas typically contains a significant amount of water vapor, which can pose challenges in its usage. Therefore, the process of removing water vapor from natural gas, known as gas dehydration, is crucial in the gas industry. The presence of water vapor in the gas supply can lead to the formation of hydrates, which can cause issues such as blockages in pipelines. To tackle this problem effectively, gas dehydration makes use of Tri ethylene glycol (TEG) as a drying agent. TEG works by selectively absorbing water vapor from the natural gas flow, thereby significantly reducing its moisture content.In the gas dehydration process, wet gas is treated by using lean glycol in an absorber, where the water vapor is removed. The resulting rich glycol is then recovered and recycled for further use. In this study, we explore the possibility of replacing nitrogen with dry natural gas in the re-generator of the glycol dehydration system. The aim is to evaluate the feasibility and effectiveness of this alternative approach. To assess the performance of both techniques, we employed HYSYS modeling and simulation. Through this analysis, we compared the capital and utility expenses associated with each method while ensuring that the glycol purity requirements remained unchanged. By examining the results obtained from the simulations, we can gain insights into the economic viability and efficiency of utilizing dry natural gas in the re-generator stage of the glycol dehydration process.In addition to the primary purpose of removing water vapor, the wet gas obtained from the stripping mechanisms in the glycol dehydration process can serve additional functions. It can be utilized to power steam pumps and compressors, thereby maximizing energy efficiency within the system. Alternatively, the wet gas can be recycled back into the process for further treatment. To develop a comprehensive understanding of the entire mechanism, we constructed a model based on the actual flow diagram. This model takes into account the various components and processes involved in the glycol dehydration system, including the stripping mechanisms and their connection to other equipment. By analyzing the data and outcomes generated by this model, we can derive valuable insights. These findings can be utilized to optimize the heat and material balance within the plant, ensuring efficient operation and potentially leading to the design of an improved system in terms of energy consumption and overall performance

In this contribution, a method based on a solid solution theory of clathrate hydrate for multiple cage occupancy, host lattice relaxation and guest-guest interactions has been presented to estimate hydrate formation conditions of binary and ternary gas mixtures. We have performed molecular modeling of structure, guest distribution, and hydrate formation conditions for the CO₂ + CH₄, and CO₂ + CH₄ + N₂ gas hydrates. In all considered systems with and without N₂, at high and medium content of CO₂ in the gas phase we have found that CO₂ is more favorable to occupy clathrate hydrate cavities than CH₄ or N₂. Addition of N₂ to the gas phase increases ratio concentration CO₂ in compressing with concentration CH₄ in clathrate hydrates and makes gas replacement more effective. The mole fractions of CO₂ in CO₂ + CH₄ + N₂ gas hydrate rapidly increases with the growth of its content in the gas phase. And the formation pressure of CO₂ + CH₄ + N₂ gas hydrate rises in comparison with the formation pressure of CO₂ + CH₄ gas hydrate. Obtained results agree with the known experimental data for simple CH₄, CO₂ gas hydrates and mixed CO₂ + CH₄ gas hydrate.

Biomarkers have the potential to aid in the study of Alzheimer’s disease (AD); unfortunately, AD biomarker values often have a high degree of overlap between healthy and AD individuals. This study investigates the potential utility of a series of novel AD biomarkers, the sixty second ¹²⁹Xe retention time, and the xenon washout parameter, based on the washout of hyperpolarized ¹²⁹Xe from the brain of AD participants following inhalation. The xenon washout parameter is influenced by cerebral perfusion, T1 relaxation of xenon, and the xenon partition coefficient, all factors influenced by AD. Participants with Alzheimer’s disease (n=4) and healthy volunteers (n=4) were imaged using hyperpolarized ¹²⁹Xe magnetic resonance imaging (MRI) and magnetic resonance spectroscopy (MRS) to determine the amount of retain xenon in the brain. At 60 sec post breath hold, AD patients retained significantly higher amounts of ¹²⁹Xe compared to healthy controls. Data was fit to a pharmacokinetic model and the xenon washout parameter was extracted. Xenon washout in white and grey matter occurs at a slower rate in Alzheimer’s participants (¹²⁹Xe half-life time of 42s and 43s, respectively) relative to controls (20s and 16s, respectively). Following larger scale clinical trials for validation, the xenon washout parameter has the potential to become a useful biomarker for the support of an AD diagnosis.

This paper addresses the atmospheric emissions from oil and gas extraction and production in Greece. The study was carried out in 2014 in the Kavala gulf, which currently is the only location of oil and gas production in Greece and where the exploration activities for hydrocarbons started in the late ‘60’s. This study presents the qualitative and quantitative characteristics of atmospheric emissions, in relation also to the emissions’ control management system. Particular reference is made to sulphur compounds since the existence of volcanic rocks results to increased amounts of H₂S. The results shows that, currently, atmospheric emissions of pollutants during extraction and production of hydrocarbons in Greece are very low and do not have any significant effect on air quality and climate change. Since it is expected that exploitation of hydrocarbons and oil and gas extraction and production will increase in the future, appropriate measures should be taken to ensure environmental protection, such as the development of integrated monitoring systems and the use of up to date emission control technologies.

In a previous study we could show a change of membrane morphology and gas separation performance by varying the recipe of a casting solution based on polysulfone in a determined solvent system. Although all results were very reproducible, all used solvents were harmful and not sustainable. In this study therefore, the solvents tetrahydrofuran (THF) and N,N-dimethylacetamide (DMAc) are replaced by the more sustainable solvents 2-methyl-tetrahydrofuran (2M-THF), N-butyl pyrrolidinone (NBP) and cyclopentyl methyl ether (CPME). The gas permeation performance and for the first time morphology of the membranes before and after solvent replacement were determined and compared by single gas permeation measurements and SEM microscopy. It is shown, that THF can be replaced by 2M-THF and NBP without decreasing the gas permeation performance. With CPME replacing THF no membranes were formed. Best gas permeation results showed systems with 2M-THF as THF alternative. Permeances for the tested gases oxygen (O2), nitrogen (N2), carbon dioxide (CO2) and methane (CH4) were 2.66·10-4, 3.89·10-5, 1.53·10-3 and 4.52·10-5 mL(STP)/cm²·min·bar, respectively. permselectivities of those membranes for the gas pairs O2/N2, CO2/N2 and CO2/CH4 were 6.7, 38.3 and 34.0, respectively. When additionally replacing DMAc in the solvent system no or only porous membranes were obtained, even if the precipitation procedure was adjusted. These findings indicate that a complete replacement of the solvent system without affecting the membrane morphology or gas permeation performance is not possible. By varying the temperature of the precipitation bath an easy adjustment to mechanically stable PSU membranes is possible, if just THF was replaced by 2M-THF.

Among other fossil fuels, natural gas is a major energy source. It is generally created saturated with water vapor. Dehydration of natural gas is vital in the gas business to remove water vapor from the gas supply, which may cause hydrate development in pipes. Gas dehydration employs Tri ethylene glycol (TEG) to remove water vapor from natural gas flow. The wet gas is dehydrated with lean glycol in an absorber, and the rich glycol is recovered and reused. This work investigates the use of dry natural gas instead of nitrogen in the glycol dehydration re-generator, and compares the results using HYSYS modeling and simulation. The two techniques were compared for capital and utility expenses, while maintaining the identical glycol purity criteria. The wet gas from the stripping mechanisms may also be utilized to run steam pumps and compressors or recycled. The model is based on the real mechanism flow diagram. Finally, the findings of this model might be used to design a new heat and material balance for the plant.

Natural gas plays a significant role in Tunisia's energy mix. Tunisia imports 66% of natural gas (NG) from Algeria (ANG), and the rest is provided by local gas fields mainly Miskar gas (MNG). To counteract this deficit, the Power-to-Gas approach emerges as a promising solution, given Tunisia's abundant renewable energy resources. By blending green hydrogen into the NG network, it is possible to (i) address the current energy crisis, (ii) lower the carbon intensity of the gas grid, and (iii) encourage sector coupling through the use of various renewable energy sources. This study presents an overview of various interchangeability indicators and investigates accordingly the allowable ratios for hydrogen blending with two types of natural gas distributed in Tunisia (ANG and MNG). It also explores the impact of hydrogen injection on the energy content variation and various combustion parameters. The results confirm that both ANG and MNG can withstand a maximum hydrogen blend of up to 20%. The article concludes with recommendations for further experimental testing of the findings and emphasizes the need to look into infrastructure and safety requirements with regards to the Natural gas network in Tunisia. This research serves as a critical step towards harnessing the potential of green hydrogen in Tunisia.

As the structure of horizontal gas wells is more complicated than that of vertical wells, the form of the liquid-carrying in different sections does not well agree. This makes it problematic to apply the widely used liquid-carrying theory of vertical gas wells in horizontal gas wells. Since the theory focused on the critical gas flow rate, it cannot quantify how much liquid it can remove. Simultaneously, it ignores the fact that the liquid-carrying ability of gas flow is limited and the producing liquid has a certain amount of flowing energy. In this study, the gas-liquid flow law of horizontal gas wells and wellhead drainage stability in different tubing depths were firstly studied. Then, the stability of gas drainage for different tubing depths was analyzed and confirmed. Given the disadvantages of the typical theory of critical gas flow, the mathematical model of different tubing depths for gas drainage is established for horizontal gas wells. The innovative model could take the energy of gas flow and liquid flow into account, and quantify the liquid volume which was removed. By verifying the model with the experiments, the result showed that the relative error of the model is generally less than 10%. It shows the research could provide a scientific basis for the analysis and liquid-carrying capacity for horizontal gas wells.

This paper is a further development of our “Proposal of a new double-nozzle technique for in-gas-jet laser resonance ionization spectroscopy” published in journal Atoms earlier in this year. Here, we propose to equip the proposed double-nozzle technique with the RF-only funnel and RF-buncher placed in the gas-jet chamber at 70 mm distance downstream the double-nozzle exit. It allows for highly effective extraction into vacuum heavy ion beams, produced in two-steps laser resonance ionization in the argon supersonic jet. We explored the operation of this new full version of the double-nozzle technique through detailed gas dynamic and then Monte Carlo trajectory simulations, which results are presented and discussed. In particularly, we have shown by calculations that more than 80% of all nobelium-254 neutral atoms, extracted by argon flow from the gas stopping cell through the double-nozzle into the supersonic jet can be extracted into vacuum in a form of pulsed ion beam having low transverse and longitudinal emittance.s dynamic and Monte Carlo simulations

The gas-water relative permeability curve plays a crucial role in reservoir simulation and development for condensate gas reservoirs. In this study, we conducted a series of high temperature and high pressure analysis experiments on real gas cores from Wells A and B in Block L of the Yinggehai Basin to investigate the effects of temperature, pressure, and different types of gas media on gas-water seepage. The experimental results demonstrate that: Temperature has a significant impact on both gas and water relative permeability, particularly on the former. As temperature increases, gas relative permeability shows a substantial increase while water relative permeability remains relatively unchanged. Under the same effective stress, increasing pressure causes downward shifts in both the gas and water relative permeability curves; however, there is a more pronounced decrease in gas relative permeability. Gas type has minimal influence on phase permeability except at higher water saturation where differences become apparent. When water saturation ranges from 80% to 50%, there is no significant variation observed in the measured relative permeability of different displacement gases; however, as water saturation exceeds 80%, distinctions gradually emerge. At bound water saturation conditions, nitrogen exhibits lower relative permeability compared to simulated gases with approximately 92% similarity between them. This investigation into the characteristics of gas-water relative permeability in high temperature and high pressure condensate reservoirs within Yinggehai Basin provides valuable insights for efficient development strategies for similar reservoirs.

A nanocomposite rod-shaped structure with single-walled carbon nanotube (SWCNT) embedded in polypyrrole (PPy) doped with nonafluorobutanesulfonic acid (C4F), SWCNT/C4F-PPy, was synthesized using emulsion polymerization. The hybrid ink was then directly coated on a polyimide film interdigitated with the Cu/Ni/Au electrodes via a screen-printing technique to create a flexible film sensor. The sensor film showed a response of 1.72% at 25 °C/atmospheric pressure when acetone gas of 5 ppm was injected, which corresponds to almost 95% compared to the Si wafer-based array interdigitated with the Au electrode. Additionally, C4F was used as a hydrophobic dopant of PPy to improve the stability of humidity and to produce a highly sensitive film-type gas sensor that provides stable detection even in humid conditions.

This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

Nowadays, the imidazolium-based ionic liquids containing acetate counter-ions are attracting much attention as both highly selective absorbents of the acidic gases and CO₂ carriers in the supported ionic liquid membranes. In this regard, the investigation of the gas transport properties of such membranes may be appropriate for better understanding of various factors affecting the separation performance and the selection of the optimal operating conditions. In this work, we have tested CH₄, CO₂ and H₂S permeability across the SILM impregnated by 1-butyl-3-methylimidazolium acetate (bmim[ace]) with the following determination of the ideal selectivity in order to compare the facilitated transport membrane performance with the SILM that dissolves acidic gases physically, namely, containing 1-butyl-3-methylimidazolium tetrafluoroborate (bmim[BF₄]). Both SILMs have showed modest individual gases permeability and ideal selectivity of CO₂/CH₄ and H₂S/CH₄ separation that achieves values up to 15 and 32, respectively. The effect of the feed gas mixture composition on the permeability of acidic gases and permeselectivity of the gas pair was investigated. It turned out that the permeation behavior for the bmim[ace]-based SILM toward the binary CO₂/CH₄, H₂S/CH₄ and ternary CO₂/H₂S/CH₄ mixtures was featured with high acidic gases selectivity due to the relatively low methane penetration through the liquid phase saturated by acidic gases.

Oleylamine capped WS2 nanostructures were successfully formed at 320 °C via a relatively simple colloidal route. SEM and TEM analyses showed that the 3D nanoflowers that were initially formed disintegrated into 2D nanosheets after prolonged incubation. XPS and XRD analyses confirmed oxidation of WS2 into WO3. Sensors based on these oleylamine capped WS2 nanoflowers and nanosheets still showed a change in electrical response towards various concentrations of NH3 vapour at room temperature in a 25% relative humidity background despite the oxidation. The nanoflowers exhibited n-type response while the nanosheets displayed a p-type response towards NH3 exposure. The nanoflower based sensors showed better response to NH3 vapour exposure than the nanosheets. The sensors showed a good selectivity towards NH3 relative to acetone, ethanol, chloroform and toluene. Meanwhile, a strong interference of humidity to the NH3 response was displayed at high relative humidity levels. The results demonstrated that oleylamine limited the extent of oxidation of WS2 nanostructures. The superior sensing performance of the nanoflowers can be attributed to their hierarchical morphology which enhances the surface area and diffusion of the analyte.

The No. 3 coal seam in the Yuxi Coal Mine has a measured maximum gas content of 25.59 m3/t, along with a maximum gas pressure of 2.9 MPa, indicating its high risk to gas and outbursts. To mitigate outburst risks of the coal seam, the 1301 working face has been implemented gas pre-drainage measures by grid boreholes from underlying roadways. After one year of extraction, it was confirmed that the gas content at all 33 test sites was below 8 m3/t, meeting the outburst prevention standards. However, during subsequent coal tunnel excavation, the gas desorption index K1 value frequently exceeded the standard, resulting in numerous occurrences of abnormal gas emission or small-scale outbursts. To tackle the challenges associated with safe excavation following the first round regional outburst prevention measures, a research and industrial trial of CO2 gas fracturing(CO2-Frac) technology for secondary outburst prevention and rapid excavation was completed. Results show that the dual-hole and high-pressure (185MPa) CO2-Frac considerably contribute to outburst prevention. K1 exceedances per hundred meters of tunnel excavations were from average 2.54 without CO2-Frac to average 0.28 after the new technology being implemented, leading to a eight fold reduction. Additionally, the monthly excavation footage increased from average 81.64 m without CO2-Frac to average 162.42 m with CO2-Frac, resulting in a 2-fold improvement. The dual-hole and high-pressure CO2-Frac is an advanced technology for safe and efficient excavation for secondary outburst elimination in highly outburst-prone coal seams in the Yuxi Coal Mine, with potential for widespread application in similar coal seam conditions.

There have been many researches on the surface acoustic wave (SAW) sensors for detecting sulfur-containing toxic or harmful gases. This paper aims to give an overview of the current state of the polymer films used in SAW sensors for detecting deleterious gases. By covering most of the important polymer materials, the structures and types of polymers are summarized, and a variety of devices with different frequency, such as delay lines and array sensors for detecting mustard gas, hydrogen sulfide and sulfur dioxide are introduced. The preparation method of polymer films, the sensitivity of the SAW gas sensor, the limit of detection, the influence of temperature and humidity, and the anti-interference ability are discussed in detail. The advantages and disadvantages of the films are also analyzed, and the potential application of polymer films in the future is also forecasted.

Ensuring fire safety is an important condition for the successful operation of industrial enterprises. It is necessary to detect the threat of fire before ignition. An indicator of danger is the appearance of gas, which occurs as a result of unauthorized heating of equipment. Gas sensors make it possible to detect the appearance of gases characteristic of the decomposition of materials at the stage of smouldering and pyrolysis, which cause a change in the composition of the atmosphere. This paper presents a mathematical method for the rational placement of gas analyzers for premises of potentially hazardous industries. It is the rational placement of gas sensors, which ensures safety, taking into account economic feasibility that determines the effectiveness of their use. For the first time, the analysis of gas accumulation during the movement of the flow from the source to the ceil-ing, then propagation to the location of the sensors, is used for the first time to select the placement of gas sensors. Depending on the permissible values of the gas volume, the placement and number of gas sensors are selected. The calculation of the conditions for the rational placement of gas sen-sors for the most common indicators, such as carbon monoxide and hydrogen at different sizes and heights of rooms, is carried out. The method of calculating the location of gas analyzers makes it possible to diagnose and predict fire hazard at technological facilities on the basis of gas control, and compare the obtained values with the maximum permissible values. This method provides cal-culation of the coordinates of the gas source from the coordinates of the triggered sensors. Knowing the coordinates of all sensors, the coordinates of the sensors that gave the alarm, and the formula for determining the volume of the gas cloud under these sensors, it is possible to assess the localization of the source of dangerous gas in the protected room. This increases the efficiency of the fire safety system. The method makes it possible to control the layout of sensors depending on the volume of protected premises, types of production, the creation of new sensors, changes in the composition of hazardous gas in different technological conditions.

Exploration practices have proven that over mature shale gas exhibits a feature of carbon isotope reversal. The geochemical statistics indicate that the wetness (C2-C5/C1-C5) of shale gas with carbon isotope reversal is less than 1.8%. In addition, the magnitude of carbon isotope reversal (δ13C1- δ13C2) for the over mature shale gas presents a parabolic variation with decreasing wetness. δ13C1-δ13C2 increases with decreasing wetness within a wetness range of 0.9% ~1.8% and then decreases with decreasing wetness at wetness < 0.9%. The CH4 cracking experiment demonstrates that CH4 polymerization occurring in the early stage of CH4 cracking is an important factor involved in isotope reversal of over mature shale gas. Moreover, δ13C1- δ13C2 decreases with an increase in experimental temperature prior to CH4 substantial cracking. The values of δ13C1 and δ13C2 tend to equalize during CH4 substantial cracking. The δ13C1-δ13C2 of mud gas present at different depths during shale gas drilling in Sichuan Basin increases initially, then decreases with further increase in the depth and finally tends to zero, with only a trace hydrocarbon gas being detectable. Statistical data suggests that the shale gas production in Sichuan Basin decreases with the decreasing δ13C1-δ13C2 value and wetness. Thus, δ13C1-δ13C2 and wetness could potentially serve as useful criteria to screen CH4 cracking degree and to determine the largest depth of natural gas exploration. Great care should be taken during shale gas exploration in deeper layers, with wetness and δ13C1-δ13C2 less than 0.2% and 1%, respectively, since very low wetness (<0.2%) and δ13C1-δ13C2 (<1%) might be indicative of CH4 substantial cracking in a geological setting.

Gas Path Analysis and matching turbine engine models to experimental data are inverse problems of mathematical modelling which are characterized by parametric uncertainty. This results from the fact that the number of measured parameters is significantly lower than the number of components’ performance parameters needed to describe the real engine. In these conditions, even small measurement errors can result in a high variation of results, and obtained efficiency, loss factors etc. can appear out of the physical range. The current methods of engine model identification have developed considerably to provide stable, precise and physically adequate solutions. Presented in this work is an estimation method of engine components’ parameters based on multi-criteria identification which provides stable estimations of parameters and their confidence intervals with the known measurement errors. A priori information about the engine, its parameters and performance is used directly in the regularised identification procedure. The mathematical basis for this approach is the fuzzy sets theory. Forming objective functions and scalar convolutions synthesis of these functions is used to estimate gas-path components’ parameters. A comparison of the proposed approach with traditional methods showed that its main advantage is high stability of estimation in the parametric uncertainty conditions. Regularization reduces scattering, excludes incorrect solutions which do not correspond to a priori assumptions, and also helps to implement the Gas Path Analysis at the limited number of measured parameters. The method can be used for matching thermodynamic models to experimental data, Gas Path Analysis and also adapting dynamic models for the needs of the engine control system.

ZnO thin films with a thickness of 300 nm were deposited on Si and Al2O3 substrates using electron beam evaporation technique with the aim to be tested as low cost and low power consumption gas sensors for ozone (O3). To characterize the surface roughness and the grain size, which are the main parameters recognized to enhance gas sensitivity since they directly influence the effective sensing area, surface morphology and roughness analyses of the films were performed using scanning electron microscopy and atomic force microscopy, respectively. The crystalline structure and elemental composition were studied through Raman spectroscopy and X-ray photoelectron spectroscopy. Gas tests were conducted at room temperature and zero-bias voltage to assess the sensitivity and response as a function of time of the films to O3 pollutant. The results indicate that the films deposited on Al2O3 exhibit promising characteristics, such as high sensitivity and a very short response time (< 2 s) to the gas concentration. Additionally, it was observed that the films display pronounced degradation effects after a significant exposure to O3.

Researchers have been exploring seaweed to reduce methane (CH4) emissions from livestock. This study aimed to investigate the potential of a red alga, Bonnemaisonia hamifera, as an alternative to mitigate CH4 emissions. B. hamifera, harvested from the West coast of Sweden, was used in an in vitro experiment using a fully automated gas production system. The experiment was a ran-domized complete block design consisting of a 48-h incubation that included a control (grass si-lage) and B. hamifera inclusions at 2.5%, 5.0% and 7.5% of grass silage OM mixed with buffered rumen fluid. Predicted in vivo CH4 production and total gas production were estimated by ap-plying a set of models to the gas production data and in vitro fermentation characteristics were evaluated. The results demonstrated that the inclusion of B. hamifera reduced (P = 0.01) predicted in vivo CH4 and total gas production, and total gas production linearly decreased (P = 0.03) with higher inclusion of B. hamifera. The molar proportion of propionate increased (P = 0.03) while isovalerate decreased (P = 0.04) with inclusion of B. hamifera. There was a tendency for increased (0.06 ≤ P ≤ 0.10) total volatile fatty acid production, as well as lower proportions of butyrate, isobutyrate, and 2-methylbutyrate. Chemical analyses revealed that B. hamifera had moderate concentrations of polyphenols. The iodine content was low and there was no detectable bromo-form, suggesting quality advantages over Asparagopsis taxiformis. Additionally, B. hamifera exhib-ited antioxidant activity comparable to the positive control Resveratrol. The findings of this study indicated that B. hamifera harvested from temperate waters in Sweden possesses capacity to mitigate CH4 in vitro.

Inert gas asphyxiation is a rarely observed form of suffocation in which the decedent breathes in an inert chemical, such as helium or nitrogen, in the absence of oxygen. The ultimate cause of death is not a result of the chemical itself, but rather from the oxygen starvation as the inert gas displaces vital oxygen. In this case report, a 66-year-old Caucasian female with a history of gastroparesis, degenerative disc disease, and chronic pain was found deceased with a plastic bag secured around her head. Plastic tubing terminated inside the bag and connected to a nearby canister of nitrogen gas. This case study discusses the challenges in determining inert gas asphyxiation as the cause of death in a postmortem setting and emphasizes the importance of understanding the decedent’s history and context of the environment in which they were found.

Gas embolism is a medical condition leading to the blockage of blood flow in the microvasculature by gas bubbles. While reported as rare, gas embolism often has devastating, fatal physiological consequences. Despite this acute importance, the genesis and evolution of air bubbles in blood vessels under different physiological conditions, such as blood viscosity and blood flow rate, is still understudied, largely because of difficult experimentation and in situ visualization. The objective of this work was to study the gas embolism phenomenon in vitro, using a microfluidic system that mimicked the architecture of microvasculature. The microfluidic systems comprised linear channels with two different air inlet types, namely, T- and Y-junctions with three different widths (20 µm, 40 µm, and 60 µm), and a 30 µm width honeycombed network with three bifurcation angles (30°, 60°, and 90°). Three synthetic liquids equivalent to 0%, 20%, and 46% hematocrit that mimicked the physiological blood viscosity and hematocrit concentrations were used. Our results show that: (i) 20 µm and 40 µm width channels had an elevated risk of gas embolism due to wide fluctuations in the total slug sizes; (ii) the resistance to the flow of air bubbles increased with the increase in the equivalent concentration of hematocrit; (iii) gas bubbles causing blockages and dampening of the flow velocity were frequently observed in 20 µm channels, and lastly (iv) increased risk of gas embolism was observed in the honeycomb architecture with 60° and 30° bifurcations. This work suggests that in vitro experimentation using microfluidic devices with microvascular tissue-like structures opens the possibility of studying this medical condition with high reproducibility and impacts the fact-based medical guidelines for preventing or mitigating iatrogenic occurrences.

sustainability reporting, critical paradigm, upstream oil, and gasThe operating activities of the upstream oil and gas industry directly impact the environment. This industry faces significant social challenges and directly impacts the environment. Many Reputable international sustainability institutions organize sustainability awards. However, community conditions do not have a positive impact on sustainability practices. There are vari-ous serious violations related to sustainability, environmental pollution, multiple cases of cor-ruption, human rights, and other violations. In contrast, the companies receiving this award also received inspection findings of violations committed by The Audit Board of the Republic of In-donesia. This study uses critical discourse analysis that begins with phenomena related to viola-tions of sustainability reporting from scientific journals and other references using a systematic literature review approach over the last ten years. It produces a critical paradigm that is not val-ue-free, which is the basis for framing thought utilizing the theory of hegemony. The results of this study indicate that the upstream oil and gas industries are obliged to implement Corporate Social Responsibility (CSR) practices and Sustainability Reports (SR), has biased factors that are contrary to the sustainability concept and are not under the sustainability award based on evi-dence obtained from the stages of manuscript analysis with systematic literature review

60\% of the global population is expected to be in cities by 2050. At the same time the climate is changing at an accelerated rate. In this short paper we discuss the conflation of these two phenomena and how it may change the cities of the future. We formulate this as an optimization problem that could help answer important questions such as where are they likely to be located? How are they to be powered? What would be their demand for mobility and how might this be met? How over or under ground might these cities be? This paper first looks at a historical paradigm of cities in the absence of the climate crisis and then proposes the new paradigm to look at cities of the future faced by the challenge of the climate change crisis.

Accurate prediction of mercury content emitted from fossil-fueled power stations is of utmost importance for environmental pollution assessment and hazard mitigation. In this paper, mercury content in the output gas of power stations’ boilers was predicted using an adaptive neuro-fuzzy inference system (ANFIS) method integrated with particle swarm optimization (PSO). The input parameters of the model include coal characteristics and the operational parameters of the boilers. The dataset has been collected from 82 power plants and employed to educate and examine the proposed model. To evaluate the performance of the proposed hybrid model of ANFIS-PSO model, the statistical meter of MARE% was implemented, which resulted in 0.003266 and 0.013272 for training and testing, respectively. Furthermore, relative errors between acquired data and predicted values were between -0.25% and 0.1%, which confirm the accuracy of the model to deal nonlinearity and representing the dependency of flue gas mercury content into the specifications of coal and the boiler type.

The hydrodynamic results obtained from the permeability of porous materials not only affect the assessment of the stream of the gas flow through those materials but they also refer to the loss of pressure energy in that flow. The direct measure of that loss is flow resistances.The results of experimental research upon the assessment of the flow resistances of porous materials with respect to gas flow. The research conducted applied to natural materials with an anisotropic gap-porous structure. The tests were carried out on a gas permeability measuring system, adapted to different shapes of porous material samples. The process issue of the total pressure drop on a porous deposit was considered in the Reynolds number category. The coefficient of flow resistance for anisotropic materials was defined and the value of this coefficient was compared to the gas stream and the total pressure drop on the porous bed was experimentally evaluated.

Simulation programs contain Computational Fluid Dynamics - CFD codes and are a useful tool used for gas flow through porous materials. Conducting numerical simulations allows for detailed analysis of hydrodynamic phenomena. The results of numerical modeling should always be verifiable based on experimental data. Only their compliance with the results of experimental tests is a determinant of the correctness of the applied method. As part of the work, experimental studies of hydrodynamics of gas flow through an isotropic porous material were carried out and numerical simulation for material of the same shape was used. In the CFD modeling Kolmogorov's hypothesis for the transport of kinetic energy of turbulence k and transport of dissipation rate of kinetic energy of turbulence ε was used.

The one-dimensional gas of bosons interacting via a repulsive contact potential was solved long ago via Bethe's ansatz by Lieb and Liniger [Phys. Rev. {\bf 130}, 1605 (1963)]. The low energy excitation spectrum is a Luttinger liquid parametrized by a conformal field theory with conformal charge $c=1$. For higher energy excitations the spectral function displays deviations from the Luttinger behavior arising from the curvature terms in the dispersion. Adding a corrective term of the form of a mobile impurity coupled to the Luttinger liquid modes corrects this problem. The ``impurity'' term is an irrelevant operator, which if treated non-perturbatively, yields the threshold singularities in the one-particle and one-hole hole Green's function correctly. We show that the exponents obtained via the finite size corrections to the ground state energy are identical to those obtained through the shift function.

This study investigated the evolution of density, gas permeability and thermal conductivity of sugar maple wood during the thermo-hygro-mechanical densification process. The results suggested that the oven-dry average density of densified samples was significantly higher than that of the control samples. However, the oven-dry density did not show a linear increase with the decrease of wood samples thickness. The radial intrinsic gas permeability of the control samples was 5 to 40 times higher than that of densified samples, which indicated that the void volume of wood was reduced notably after the densification process. The thermal conductivity increased by 0.5 - 1.5% per percent increase of moisture content for densified samples. The thermal conductivity of densified wood was lower than that of the control samples. The densification time had significant effects on the oven-dry density and gas permeability. Both the densification time and the moisture content had significant effects on thermal conductivity, but their interaction effect was not significant.

High-throughput screening of samples is the strategy of choice to detect occupational exposure biomarkers, yet it requires user-friendly apparatus that gives relatively prompt results while ensuring high degrees of selectivity, precision, accuracy and automation, particularly in preparation processes. In the last 10 years, miniaturization has attracted much attention in analytical chemistry and has driven solvent and sample savings and easier automation, the latter thanks to the introduction on the market of three axis autosampler. In light of the above, this contribution describes a novel user-friendly solid-phase microextraction (SPME) off- and on-line platform coupled with gas chromatography triple quadrupole-mass spectrometry to determine urinary 1- and 2-hydroxy-napthalene, 9-hydroxy-phenantrene, 1-hydroxy-pyrene, 3- and 9-hydroxy-benzoantracene and 3-hydroxy-benzo[a]pyrene, metabolites of the related polycyclic aromatic hydrocarbons. In this new procedure chromatography’s sensitivity is combined with the user-friendliness of N-tert-butyldimethylsilyl-N-methyltrifluoroacetamide on-fiber SPME derivatization previous direct immersion sampling, to which is added the quantitative accuracy afforded using specific isotope-labelled internal standards. The detection limits for the seven OH-PAHs were ranged from 0.28 to 1.87 ng/L. Intra-(from 2.5 to 3.0%) and inter-session (from 2.4 to 3.9%) repeatability was also evaluated. This method serves to identify suitable risk-control strategies for occupational hygiene conservation programs

A lead zirconate titanate [PZT;Pb(Zr_0.52Ti_0.48)O₃] layer embedded infrared (IR) detector decorated with wavelength-selective plasmonic crystals has been investigated for high-performance non-dispersive infrared (NDIR) spectroscopy. A plasmonic IR detector with an enhanced IR absorption band has been designed based on numerical simulations, fabricated by conventional microfabrication techniques, and characterized with a broadly tunable quantum cascade laser. The enhanced responsivity of the plasmonic IR detector at specific wavelength band has improved the performance of NDIR spectroscopy and pushed the limit of detection (LOD) by an order of magnitude. In this paper, a 13 fold enhancement in the LOD of a methane gas sensing using NDIR spectroscopy is demonstrated with the plasmonic IR detector.

The physical properties of coal reservoirs are the main restrictions to exploration and development of CBM. The study of the physical characteristics of coal reservoirs and their controlling factors is of great significance to the safe and efficient development and utilization of CBM resources in the mining area. The Pingdingshan No. 10 coal mine was chosen for this study because of its better gas production effect at the test wells. The reservoir properties of the main coal seams of the No. 10 coal mine were tested and analyzed to comprehensively evaluate the reservoir properties. The results indicate that (1) The gas content and methane purity of the No. 4 coal seam are significantly higher than the No. 2 seam, and therefore they have better development potential than the No. 2 seam; (2) The average adsorption time of the No. 2 coal seam is less than that of the No. 4 seam, making it easier to reach the peak production capacity of CBM wells in the short term, but is not conducive to long-term stable production of CBM. The Langmuir volume of the No. 2 coal seam samples was significantly greater than for the No. 4 coal seam; however, the No. 4 coal seam contains about three times the amount of gas in the No. 2 seam; (3) All three coal seams have high porosity, which is favorable for large amounts of CBM adsorption and storage. Micropores predominate, transitional pores are less frequent, and a few mesopores occur; macropores are the least common. Samples from the No. 4 seam contained the highest proportion of micropores; (4) Organic pores were common in the all coal samples, with pore diameters not more than 30 µm, mainly concentrated between 50.5 and 1000 nm. Microfractures with aperture less than 70 nm were relatively frequent, mainly in the 50–65 nm range. A large number of the nanoscale microfractures were curved or jagged; (5) Fractures in the No. 2 and No. 4 coal seam samples with widths of 50 nm to 20 µm were more developed, and many were filled with kaolinite, quartz and other minerals; (6) The samples contained mostly layered silicate minerals (kaolinite), with hard granular minerals (quartz) next, and a very small quantity of iron-type minerals such as siderite and pyrite in dendritic form. The results of this study can provide a reference basis for the large-scale development and utilization of subsequent CBM wells.

The Pingbei area is the main accumulation area of oil and gas in the Xihu Sag. The phase characteristics of oil and gas in this area are complex, and the understanding of their genesis is still unclear. In this paper, based upon discussions of crude oil and natural gas geochemical data, integrated with local geological features, we discuss the sources, migration, and phase state characteristics of oil and gas in the Pingbei area of the Xihu Sag. The study results showed that the crude oil and natural gas in the Pingbei area are coal-derived and the oil and gas produced by the humic organic matter during the maturity stage. The oil and gas source correlation showed that crude oil and natural gas have good affinity with the Eocene Pinghu Formation (PF) coal-bearing source rocks. Crude oil has the characteristics of near-source accumulation and short-distance migration while natural gas is supplied from a dual source: the coal-derived hydrocarbon rocks of PH in the deep part of the study area, supplemented by the coal-derived hydrocarbon rocks of PH on the bottom of the slope, and adjacent hydrocarbon-bearing sub sag. The distribution characteristics and geochemical migration indices of hydrocarbon showed that the oil generated from the hydrocarbon source rocks of PH in the deep Pingbei area mainly migrates vertically along the fault connecting the reservoir and the source rocks to the trap, where it accumulates, while the natural gas exhibits deep and large faults that mainly migrate vertically, supplemented by its lateral migration along the composite transport system composed of faults and sandstone layers in the slope zone. The mechanisms of produced, exhausted, and geochromatographic effects (PGE), as well as evaporative fractionation (EF) and phase-controlled migration fractionation (PMF), result in the obvious discrepancy of hydrocarbon’s properties on the vertical profiles.

Background: Mitigating climate change requires fundamentally redesigned energy systems in which renewable energy sources ultimately replace fossil fuels such as natural gas. In this context, the question how and to which extent the gas sector can contribute to an increasingly climate-neutral future EU energy system is heavily debated among scholars, energy industry experts and policy makers. Methods: We take a two-step approach: We begin with a review of studies from energy industry and academia to discuss potential gas sector contributions from a holistic energy system design point of view; this is followed by a comprehensive discussion of technical potentials, micro-economic conditions and societal implications of renewable gas. We then enrich our findings with the results of an empirical focus group process. Results: The gas sector can not only contribute to balancing volatile renewable energy production but also enable the supply of renewable energy to end-users in gaseous form; based on existing infrastructure. This could reduce costs for society, increase public acceptance and ultimately speed up the energy system transformation. There is the theoretical technical potential to substitute major parts of natural gas with renewable gas of biogenic and synthetic nature. This, however, crucially requires a supportive policy framework like the one established for renewable electricity. Conclusion: Given the societal benefits and the competitiveness of renewable gas as compared to renewable alternatives, energy policy makers should incorporate renewable gas and the existing gas infrastructure in the future energy system framework. The objective should be an optimized interplay of various energy vectors and their infrastructure along the entire energy supply chain. This requires a level playing field for different renewable technologies across different policy areas and a form of public support that strikes the balance between facilitating the gradual substitution of natural gas by renewable gas while maintaining public acceptance for this transformation despite higher costs for end-users.: Given the societal benefits and the competitiveness of renewable gas as compared to renewable alternatives, energy policy makers should incorporate renewable gas and the existing gas infrastructure in the future energy system framework. The objective should be an optimized interplay of various energy vectors and their infrastructure along the entire energy supply chain. This requires a level playing field for different renewable technologies across different policy areas and a form of public support that strikes the balance between facilitating the gradual substitution of natural gas by renewable gas while maintaining public acceptance for this transformation despite higher costs for end-users.

Considerable attention has recently been given to the contribution of greenhouse gas (GHG) emissions of the healthcare sector to climate change, which represents 4-6% of emissions worldwide. GHGs used in medical practice are regularly released into the atmosphere and contribute to elevation in global temperatures that produce detrimental effects on the environment and human health. Consequently, a comprehensive assessment of their global warming potential (GWP) characteristics and clinical uses, many of which have evaded scrutiny from policy makers due to their medical necessity, is needed. Of major interest are volatile anesthetics, analgesics, and inhalers, as well as fluorinated gases used as tamponades in retinal detachment surgery. In this review, we compare estimates of these gases’ GHG emissions in metric tons CO₂ equivalent (MTCO₂e) and their relative GWP. Notably, the anesthetics desflurane and nitrous oxide contribute the most emissions out of the major medical GHGs, equivalent to driving 12 million gasoline-powered cars annually in the US. Retinal tamponade gases have markedly high GWP up to 23,500 times compared to CO₂ and long atmospheric lifetimes up to 10,000 years, thus bearing the potential to contribute to climate change long-term. This review provides the basis for discussions on examining the environmental impacts of medical gases with high GWP, determining whether alternatives may be available, and reducing emissions while maintaining or even improving patient care.

A Natural gas is increasingly being sought after as a vital source of energy, given that its production is very cheap and does not cause the same environmental harms that other resources, such as coal combustion, do. Understanding and characterizing the behavior of natural gas is essential in hydrocarbon reservoir engineering, natural gas transport, and process. Natural gas compressibility factor, as a critical parameter, defines the compression and expansion characteristics of natural gas under different conditions. In this study, a simple second-order polynomial model based on the group method of data handling (GMDH) is presented to determine the compressibility factor of different natural gases at different conditions, using corresponding state principles. The accuracy of the model evaluated through graphical and statistical analyses. The results show that the model is capable of predicting natural gas compressibility with an average absolute error of only 2.88%, a root means square of 0.03, and a regression coefficient of 0.92. The performance of the developed model compared to widely known, previously published equations of state (EOSs) and correlations, and the precision of the results demonstrates its superiority over all other correlations and EOSs.

The operation of electricity and natural gas transmission networks in the U.S. are increasingly interdependent, due to the growing number of installations of gas fired generators and the penetration of renewable energy sources. This development suggests the need for closer communication and coordination between gas and power transmission system operators in order to improve the efficiency and reliability of the combined energy system. In this paper, we present a co-simulation platform for examining the interdependence between natural gas and electricity transmission networks based on a direct current unit-commitment and economic dispatch model for the power system and a transient hydraulic gas model for the gas system. We analyze the value of day-ahead coordination of power and natural gas network operations and show the importance of considering gas system constraints when analyzing power systems operation with high penetration of gas generators and renewable energy sources. Results show that day-ahead coordination contributes to a reduction in curtailed gas during high stress periods (e.g., large gas offtake ramps) and a reduction in energy consumption of gas compressor stations.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Recently, flares have been considered as a major source of air pollution from the petroleum refining industry. The United Nations have instigated an international effort related to the management of flare emissions to reduce the global warming impact related to flaring. Eliminating or removing the need for gas flares is difficult because these devices are generally used as safety devices to allow combustion of flammable gases in a controlled fashion which supports safe operation. However, reducing flaring is generally possible using well designed efficiently operated flare equipment. In general, flare performance can be enhanced following the API-521 methodology and using assist- media including air and steam to achieve smokeless operation. This present work will discuss flare emissions in petroleum refining industry, and a method to manage flare emissions. Moreover, this work will discuss flare Combustion Efficiency (CE) and Distraction and Removal Efficiency (DRE) in terms of efficient flare operation. This work uses actual operating flare data, published previously, will be used in this work together with the CFD Code C3d. This code, developed at the USDOE Sandia National Laboratory is based on a standard LES methodology to conduct transient flare analysis is used to simulate flare operation to estimate flame shape and emissions produced. In this work, a new air-assisted flare tip design which uses the Coanda effect to improve flare operation was analysed. This new flare design reduces the emission rate that demonstrates the design effectiveness. The analysis considers a flare 1m high and (6") diameter in the centre of a 4m*4m*4m domain. Boundary conditions considering no cross wind and an ambient temperature of 300K. The initial condition is a hydrostatic pressure profile across the computational domain. In the air assist simulation, stoichiometric ratio will be a variable and therefore more than one case was considered.

The brown pelican (Pelecanus occidentalis) is a species often affected by natural and man-made disasters such as hurricanes and oil spills as well as general human activities; that subsequently receives medical care and rehabilitation. During rehabilitation, blood may be collected for various testing to help with diagnosis, treatment, and monitoring. Reference intervals for this species are limited, dated, and typically from small sample sizes. Seventy one presumed healthy brown pelicans were sampled as a part of their pre-release examination from rehabilitation at the Wildlife Center of Texas after a large volume stranding in December 2014 to January 2015, and various venous analytes were measured to establish updated reference intervals for Brown Pelicans. Fibrinogen was measured via heat precipitation and the Abaxis VSPro equine Fibrinogen cartridge to determine reference intervals, and in an attempt to validate the VSPro for use in avian species. Abaxis VS2 Avian/Reptile Chemistry panel, iSTAT CG4+, and iSTAT Chem8+ results in addition to body condition score, spun PCV, cloacal temperature and fibrinogen were measured. Proposed reference intervals for brown pelicans are presented. Fibrinogen results were not comparable between the gold standard method and the VSPro, indicating that the VSPro is not appropriate for use in brown pelicans.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

Hydrogen from natural gas reforming can be produced efficiently with a high CO2 capture rate. This can be achieved with oxygen-blown autothermal reforming as core technology combined with pressure-swing adsorption for hydrogen purification and refrigeration-based tail gas separation for CO2 capture and recirculation of residual hydrogen, carbon monoxide and methane. The low-temperature tail gas separation section is presented in detail, and to quantify the exergy efficiency of this section, a detailed exergy analysis is conducted. The irreversibilities in 42 different process components are quantified. In order to provide a transparent verification of the consistency of exergy calculations, the total irreversibility rate is calculated by two independent approaches: Through the bottom-up approach, all individual irreversibilities are added to obtain the total irreversibility rate. Through the top-down approach, the total irreversibility rate is calculated solely by the exergy flows crossing the control volume boundaries. The consistency is verified as the comparison of results obtained by the two methods shows a relative deviation of 4·10-7. The exergy efficiency of the CO2 capture process is calculated based on two different definitions. Both methods give a baseline exergy efficiency of 58.38%, which indicates a high degree of exergy utilisation in the process.

Computational Fluid Dynamics (CFD) is revolutionizing the oil and gas industry by offering powerful insights and innovative solutions. This paper explores the cutting-edge applications of CFD in enhancing and innovating within the sector. CFD simulations provide engineers with invaluable insights into fluid behavior, enabling optimized designs and informed decision-making. The software facilitates foresight by predicting system performance, optimizing drilling techniques, and maximizing reservoir management strategies. Moreover, CFD optimizes equipment design, increases operational efficiency, and reduces costs through virtual testing, eliminating the need for costly physical prototypes. The application of CFD aligns with the United Nations Sustainable Development Goals (SDGs), promoting energy efficiency, climate action, responsible production, and sustainable consumption. It addresses flow assurance challenges, enhances safety protocols, and mitigates environmental impacts. CFD is a powerful tool driving innovation, resilience, and sustainability within the oil and gas industry, ensuring a more efficient, safe, and environmentally conscious future. As advancements in CFD methodologies continue, the potential for further enhancements and breakthroughs within the sector becomes even more promising, driving the industry towards a sustainable and prosperous future.

Cellulose-based carbon (CBC) has been widely concerned with its porous structure, high specific surface area, and is liable to adsorb gas molecules and macromolecular pollutants. However, the application of CBC in gas sensing has been little studied. In this paper, ZnO/CBC heterojunction was formed by means of simple co-precipitation and high temperature carbonization. As a new ammonia sensor, the prepared ZnO/CBC sensor can detect ammonia compared with that of the previous pure ZnO ammonia sensor can not at room temperature. It has great gas sensing response, stability and selectivity to ammonia concentration at 200 ppm. This study provides a new idea for the design and synthesis of biomass carbon-metal oxide composites.

The scope of this paper is to use plastic waste through the gasification process for producing electricity with low carbon dioxide emissions. Worldwide, plastic production increased, reaching 367 million tons in 2020, compared with 1.5 million tons in 1950. It is known that plastic incineration generates approximately 400 million tons of CO2 annually, and consequently, new solutions for a more efficient plastics reuse in terms of emissions generated are still expected. One method is to use plastic waste in a gasifier unit and the syngas generated in a gas turbine for electricity production. The co-gasification process (plastic waste with biomass) was analysed in different ratios. Gasification was carried out with air for an equivalent ratio (ER) between 0.10-0.45. The volume concentration of CO2 in syngas ranged from 2-12%, with the highest value obtained when poplar content in the mix was 95%. In this study, the option of pre- and post-combustion integration of the chemical absorption process (CAP) was investigated. Thus, CO2 emissions have decreased by 90% compared with the case without CO2 capture. By integrating the capture process, the global efficiency has reduced with 5.5 – 6.1 percentage points in a post-combustion case, according to the plastic content in the mix.

Detection of partial discharge (PD) activities in high-voltage equipment can be done according to the several mechanisms of signal detection, which are electromagnetic wave signal detection, acoustic signal detection, chemical reactions, electrical signal detection, or optical emission detection. Recently, multiple methods of detection and localization of partial discharge activities occurred in power transformers and gas-insulated switchgear (GIS) have been proposed to monitor the health condition of high-voltage equipment, especially when the awareness regarding preventive maintenance has been emphasized at the industrial level and electrical providers. In aligning the needs of industrial and the improvement of PD detection methods, this manuscript focused on reviewing the current practice methods for the detection and localization of PD signals in high-voltage equipment and comparing their efficacy, in summarizing the future direction of research work-related methods of PD detection. The comparative reviews are discussed in terms of the mechanism of PD signal detection, indication parameters, calibration technique, advantages, and limitations of each method of PD measurement in detail.

Methane is the main cause of sewer explosion accidents, and the available monitoring methods mainly use portable gas sensors for on-site detection. However, these methods cannot grasp the dynamic changes in methane in a sewer in real time or make better predictions of methane explosion accidents. Here, we present a low-power online monitoring system for sewer methane in order to ensure the safety of urban sewers. A low-power ultrasonic gas sensor was used to monitor the methane content in biogas. Due to the impacts of changes in CO2, temperature, and humidity in the sewer on the ultrasonic methane measurement results, a corresponding compensation method was proposed. The effectiveness of the compensation method was verified through experiments, which measured the methane concentration under different influences, and the methane values measured before and after compensation were compared. The power consumption was only 1.28 mW if the system worked in intermittent operation mode, and it could operate for about 1.5 years by selecting a lithium battery with a capacity of 5 A · H. The experimental results showed that the gas detection accuracy could meet the commercial requirements and had a high compensation for the impacts of carbon dioxide, temperature, and humidity.

A set of aromatic copolyimides was obtained by reaction of 4,4′-(hexafluoroisopropylidene) diphthalic anhydride (6FDA), and mixtures of the diamines 1,4-bis(4-amino-2-trifluoromethylphenoxy)-2,5-di-tert-butylbenzene (CF3TBAPB) and 3,5-diamino benzoic acid (DABA). These polymers were characterized and compared with the homopolymer derived from 6FDA and CF3TBAPB. All copolyimides showed high molecular weight values and good mechanical properties. The presence of carboxylic groups in these copolymers allowed their cross-linking by reaction with 1,4-butanediol. The crosslinked polymer films were extensively characterized and it was observed that the degree of crosslinking was low in the copolyimides possessing a small number of carboxyl groups. The degradation temperature of these crosslinked copolyimides was lower than their corresponding non-crosslinked ones. Glass transition temperatures were higher than 260 oC, showing the non-crosslinked copolyimides the highest values. Young moduli of these crosslinked showed values higher than 1.9 GPa, and slightly lower elongation at break when compared with the precursor copolyimides. All copolyimides (precursor, and crosslinked ones) films could be tested as gas separation membranes. It was seen that CO2 permeability values were around 100 barrer, having better selectivity than that of the homopolymer. Moreover, the plasticization resistance of the crosslinked material having a large number of carboxylic groups was excellent.

This investigation was conducted to determine the chemical composition and nutritional value of five plant species commonly used as ruminant feeds namely: Artemisia herba-alba, Acer monspessulanum, Amygdalus lycoides, Amygdalus scoparia, and Atriplex leucoclada. After the collecting samples, the chemical compositions of plants included dry matter (DM), organic matter (OM), crude protein (CP), ether extract (EE), ash (CA), cell wall (NDF), and non-lignin cell wall (ADF) were determined according to standard methods. For degradation testing, the nylon bag technique was applied using three native Sistani fistula calves. Organic matter digestibility (OMD) and metabolisable energy (ME) were determined through the gas production technique. The CP value ranged from 5.30 (Amygdalus scoparia) to 11.72% (Atriplex leucoclada) while NDF value ranged from 52.62 (Amygdalus lycoides) to 69.05% (Amygdalus scoparia). The range of OMD, DOMD, and ME was from 36.67 to 53.27%, 34.67 to 49.11%, and 5.57 to 8.08 (MJ/kg), respectively. The results showed a positive correlation between cell wall composition and dry matter digestibility in plant species. The nutritional value of Amygdalus lycoides, Atriplex leucoclada, Acer monspessulanum, and Artemisia herba-alba was acceptable composition and digestibility.

To achieve efficient utilization of low-concentration mine gas, reduce resource waste, and alleviate environmental pollution, high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50% that is directly discharged into the atmosphere during coal mine production was oxidized to recover heat for reuse. The gas oxidation equipment was improved for the heating process, and the safety of low-concentration gas oxidation under high-temperature environment was evaluated. Experimental results showed that the reactor could provide a 1000 ℃ high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-temperature environment of 1000 ℃. The outlet pressure was significantly greater than the inlet pressure, and the pressure difference between the inlet and outlet exhibited a trend to increase with the gas concentration. The explosion limit varied with the temperature and the blend with oxidation products. The ratio of measured gas pressure to air pressure after oxidation was below the explosion criterion, indicating that the measured concentration gas is still safe after the shift of explosion limit, which provides a safe concentration range for efficient use of low-concentration gas in the future.

Background: Qazvin province has suffered a lot of natural disasters (earthquakes) for a long time. so, the establishment of the first industrial city in Iran, has always been a source of concern. One of these problems is the possibility of chlorine gas leaking from the chlorination system of drinking water and treatment plant the existing ones are on the health of the inhabitants of this region.Material and method: This analytical study was carried out in Novorossiysk district of Alborz in December 2012. Initially, chlorine gas leakage scenarios from these facilities were simulated by ALOHA and WISER software, and then using the Emergency Level System, according to the CCPS Consultative Center's Chemical Process Safety Advice, the Emergency Response Program was presented. Results: ALOHA software, in comparison with WISER software, has more precision to identify and address the consequences of chlorine gas leakage hazards and according to the simulation of this software in the event of a leak from the well and water resources unit at 8240 m from the area and at night 7520 meters will be affected. Due to the speed of delivering results through the WISER software, this software can be used at times when the operating speed is considered (incident time).Conclusion: According to the CCPS model, the emergency conditions were classified at levels 3 and 4, therefore, the relevant crisis management agencies (Qazvin Crisis Management Committee, Alborz City Health Center, Red Crescent and Firefighting Authority) should provide training maneuvers At Alborz city level, and informing people of cities and industrial companies, many efforts have been made to reduce human and environmental damage in case of possible leakage.

The aim of the study was to examine the biogas and methane yield of maize silage, a wastes in agricultural point of view and compare it to the biogas productivity of commonly used mixture of maize silage and mixed fodder with water. The experimental study was carried out into 2 parts. Firstly, the batch experiment was conducted in Mesophilic conditions (35°C), at five different hydraulic retention times (HRT): 6 DAT, 11 DAT 20 DAT 29 DAT and 41 DAT. The results revealed that maize silage was generated the highest biogas yield of 537 mL /241 mL at the HRT of 6days /41 days. Mixed fodder produced the highest biogas yield of 421 mL at the HRT of 6th days and the lowest one was 252 mL at the HRT of 20th days. Finally, the methane, carbon dioxide and hydrogen sulphide of biogas produced from maize silage and mixed fodder were analyzed using a gas chromatography. The results shown that biogas from maize silage precedes the gas less than the mixed fodder. In the field level experiment proved that from mixed fodder produced gas which would be enough for 7 member’s family used 3 months for the purpose of their cooking.

Gas membrane-based separation is considered one of the furthermost effective technology to address energy efficiency and large footprint challenges. Various classes of advanced materials including polymers, zeolites, porous carbons and metal–organic frameworks (MOFs) were attempted as membranes for gas separation. MOFs, among other porous materials, possess uniquely tunable nature, in which the pore size and environment can be controlled by connecting metal ions (or metal ion clusters) with organic linkers with various functionalities. This feature makes them attractive for thin membrane fabrication, as both diffusion and solubility components of permeability can be altered. It is interesting to notice that numerous reports have addressed the synthesis of different MOFs, fabrication of their corresponding thin films and their applications, nonetheless, relatively limited studies addressed their gas separation application as membranes. In this review, we provide a synopsis of the various MOF-based membranes that were fabricated in the last decade. In this review we propose a short introduction touching on the gas separation membrane technology and we shed light on (i) the various techniques developed for the fabrication of MOF as membranes and (ii) challenges and application for MOF thin film membranes in various important gas separation applications.

Accent is on determination of appropriate friction factor of the pipes and on selection of the representative equation for water or natural gas flow which is valuable for existing conditions in the looped network of pipelines. Note that in a municipal gas pipeline, natural gas can be treated as incompressible fluid (liquid) i.e. as water or oil. Even under this circumstance, calculation of water pipelines cannot be literary copied and applied for calculation of gas pipelines. Inappropriate friction factor, equally as e.g. inappropriate usage of water flow equations for calculation of gas networks can lead to inaccurate final results. Few iterative methods for determining the optimal hydraulic solution of water- and gas- looped pipeline networks, such as, Hardy Cross, modified Hardy Cross, node-loop method, node and M.M. Andrijashev method, will be shown. Speed of convergence will be compared and discussed using a simple network with three loops.

Due to failure of the continuum hypothesis for higher Knudsen numbers, rarefied gases and microflows of gases are particularly difficult to model. Macroscopic transport equations compete with particle methods, such as DSMC to find accurate solutions in the rarefied gas regime. Due to growing interest in micro flow applications, such as micro fuel cells, it is important to model and understand evaporation in this flow regime. Here, evaporation boundary conditions for the R13 equations, which are macroscopic transport equations with applicability in the rarefied gas regime, are derived. The new equations utilize Onsager relations, linear relations between thermodynamic fluxes and forces, with constant coefficients, that need to be determined. For this, the boundary conditions are fitted to DSMC data and compared to other R13 boundary conditions from kinetic theory and Navier-Stokes-Fourier (NSF) solutions for two one-dimensional steady-state problems. Overall, the suggested fittings of the new phenomenological boundary conditions show better agreement to DSMC than the alternative kinetic theory evaporation boundary conditions for R13. Furthermore, the new evaporation boundary conditions for R13 are implemented in a code for the numerical solution of complex, two-dimensional geometries and compared to NSF solutions. Different flow patterns between R13 and NSF for higher Knudsen numbers are observed.

The article discusses the validation process of a certain method of balancing gas contained in the pore space of rocks. The validation was based upon juxtaposition of the examination of rocks' porosity and the effects of comminution in terms of assessing the possibility of opening the pore space. The tests were carried out for six dolomite samples taken from different areas of the 'Polkowice-Sieroszowice’ copper mine in Poland. Before the rock material was ground, it was examined using the porosimetric method and subsequently subjected to the SEM analysis. After grinding, the research material was subjected to the granulometric analysis. Prior to the grinding process, the rocks' porosity fell in the range of 0.3-14.8%, while the volume of the open pores was included in the 0.01-0.06 cm3/g range. The research material was also characterized by inhomogeneous distribution of the pore volume. The grinding process was performed using an original device – the GPR analyzer. The ground samples were characterized by similar particle size distribution and mean diameters D_3.2 of about 4.0-4.5 µm. The SEM analysis revealed pores of various size and shape on the surface of the rock cores, while at the same time demonstrating lack of pores following the grinding process. The grain size distribution curves were compared with the cumulative pore volume curves of the cores before grinding. The resulting intersection points of both curves were seen as testifying to the presence of openings in the rock pores and release of the accumulated gas. The opening percentage of the pore space was associated with the coordinates of the curves' intersections. In order to confirm the argument put forward in this paper – i.e. that comminution of a rock to grains of a size comparable with the size of the rock's pores results in the release of gas contained in the pore space – the amount of gas released as a result of the comminution process was studied. The results of gas balancing demonstrated that the pore space of the investigated dolomites was filled with gas in amounts from 3.19 cm3/kg to 45.86 cm3/kg. The obtained results of the rock material comminution to grains comparable – in terms of size – to the size of the pores of investigated rocks, along with asserting the presence of gas in the pore space of the studied dolomites, were regarded as a proof that the method of balancing gas in rocks via rock comminution is correct.

The air in subterranean karst cavities is often depleted in methane (CH₄) relative to the atmosphere. Karst is considered a potential sink for the atmospheric greenhouse gas CH₄ because its subsurface drainage networks and solution-enlarged fractures facilitate atmospheric exchange. Karst landscapes cover about 14% of earth’s continental surface, but observations of CH₄ concentrations in cave air are limited to localized studies in Gibraltar, Spain, Indiana (USA), Vietnam, Australia, and by incomplete isotopic data. To test if karst is acting as a global CH₄ sink, we measured the CH₄ concentrations, δ¹³C_CH4, and δ²H_CH4 values of cave air from 33 caves in the USA and three caves in New Zealand. We also measured CO₂ concentrations, δ¹³C_CO2, and radon (Rn) concentrations to support CH₄ data interpretation by assessing cave air residence times and mixing processes. Among these caves, 35 exhibited subatmospheric CH₄ concentrations in at least one location compared to their local atmospheric backgrounds. CH₄ concentrations, δ¹³C_CH4, and δ²H_CH4 values suggest that microbial methanotrophy within caves is the primary CH₄ consumption mechanism. Only 5 locations from 3 caves showed elevated CH₄ concentrations compared to the atmospheric background and could be ascribed to local CH₄ sources from sewage and outgassing swamp water. Several associated δ¹³C_CH4 and δ²H_CH4 values point to carbonate reduction and acetate fermentation as biochemical pathways of limited methanogenesis in karst environments and suggest that these pathways occur in the environment over large spatial scales. Our data show that karst environments function as a global CH₄ sink.

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) are fa-vorable sensor materials because of their large surface area, ease of fabrication, and cost effec-tiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computa-tional simulations do not always match experimental results, and even experimental results re-ported by different researchers have not been consistent. In the present study, we explored the effects of metal decorations on LIG gas sensors, with NO2 and NH3 gases as representative oxi-dizing and reducing agents, respectively. To eliminate unwanted side effects arising from metal salt residues, metal NPs were directly deposited by vacuum evaporation. Although the gas sen-sitivities of the sensors deteriorate upon metal decoration irrespective of the metal work function in the case of NO2 gas, they improve upon metal decoration in the case of NH3 exposure. A careful investigation of the chemical structure and morphology of the metal NPs in the LIG sensors shows that the spontaneous oxidation of metal NPs with a low work function changes the be-havior of the LIG gas sensors and that the sensor behaviors under NO2 and NH3 gases follow different principles.

India, the world’s most populous country, is the world's third-largest emitter of greenhouse gases (GHGs). Despite employing several energy sources, it still relies heavily on coal, its primary energy source. Given India’s swiftly rising energy demand, this challenges meeting emission reduction targets. India has significantly increased investments in renewables like solar and hydrogen in recent years. While commendable, these initiatives alone cannot meet the country's expanding energy demands. In the short term, India must rely on both domestic and imported fossil fuels, with natural gas being the most environmentally friendly option. In this context, this paper attempts to forecast energy consumption, natural gas production, and consumption in India till 2050 using both univariate and multivariate forecasting methods. For multivariate forecasting, we have assumed two alternative possibilities for GDP growth: the business-as-usual and the high-growth scenarios. Each of our forecasts indicates a notable shortfall in the projected production of natural gas compared to the expected demand, implying our results are robust. Our model predicts that nearly 30-50 percent of India’s natural gas consumption will be met by imports, mainly in the form of LNG. Based on these findings, this paper recommends that Indian government policies emphasize increasing domestic natural gas production, importing LNG, and expanding renewable energy resources.

In this study, the asymmetric effect of oil and natural gas price shocks on the trade balance of 11 CESEE countries was estimated. These countries are net importers of oil and natural gas, and price shocks are often the cause of imbalances in trade. Quarterly data for the period 1994Q1 to 2023Q4 and nonlinear ARDL model were used. In the long run, a significant asymmetric effect due to the oil price shock on the trade balance of Bulgaria, Czechia, Latvia and Slovenia was found, as well as a significant asymmetric effect due to the natural gas price shock on the trade balance of Croatia. Also in the long run, a significant asymmetric effect due to wholesale prices on the trade balance of Romania, Bulgaria and Croatia was found as well as a significant asymmetric effect due to industrial production on the trade balance of Croatia, Czechia and Latvia was found, in addition to a significant asymmetric effect due to the exchange rate on the trade balance of Czechia, Poland and Romania.

Dehydration of hydrogen gas is one of the important steps in many industrial purposes thus, drying systems have been developed with high-efficiency and relative effect. In this article, the basic principles and design of a three-bed TSA (Temperature Swing Adsorption) dryer for dehydration operation of hydrogen gas drying are described in detail. The text commences with an in-depth explanation of the basic principles behind TSA technology such as adsorption and desorption mechanisms, thermodynamic considerations and material selection for adsorbents. This paper also deals with the detailed design of a three-bed TSA dryer, explaining about various fabricating details that influences both performance and total operability. The third part focuses the operational phase, and especially in cycle time, regeneration strategy and efficiency of energy. Advanced optimisation techniques are employed to lower energy consumption, increase throughput capacity and improve overall system. This detailed study will be of great help for engineers and investigators working on TSA systems design and optimization to dehydrate hydrogen gas, contributing towards the betterment in this important field dealing with industrial gas processing.

The erosion of surface pipelines induced by proppant flowback during shale gas production is significant. The surface pipelines in a shale gas field in the Sichuan Basin experienced perforation failures after only five months of service. To investigate the erosion features of L360N, coatings, and ceramics and optimize the selection of two protective materials, a gas-solid two-phase flow jet erosion experimental device was used to explore the erosion resistance of L360N, coating, and ceramic under different impact velocities (15 m/s, 20 m/s, and 30 m/s). An energy dispersive spectroscope, a scanning electron microscope, and a laser confocal microscope were employed to analyze erosion morphologies. With the increase in flow velocity, erosion depth and erosion rate of L360N, coating, and ceramic increased and peaked under an impact velocity of 30 m/s. Maximum erosion rate and maximum erosion depth of L360N were respectively 0.0350 mg/g and 37.5365 µm. Its primary material removal mechanism was plowing of solid particles and microcracks were distributed on the material surface under high flow velocities. Maximum erosion rate and maximum erosion depth of coating were respectively 0.0217 mg/g and 18.9964 µm. Its primary material removal mechanism was the detachment of the binder phase Co caused by plowing. Maximum erosion rate and maximum erosion depth of ceramics were respectively 0.0108 mg/g and 12.4856 µm. The erosion mechanisms were micro-cutting and plowing. Under different particle impact velocity, different erosion morphologies were observed, but the primary erosion mechanism was the same. The erosion resistance of ceramics was higher than that of coating. Therefore, ceramic lining materials could be used to protect the easily eroded parts, such as pipeline bends and tees, and reduce the failure rate by more than 93%. The study provided the data and theoretical basis for the theoretical study on oil and gas pipeline erosion and pipeline material selection.

The porosity of freshwater and sea ice is one of the main parameters that determine its strength. The strength of ice varies over a wide range of values, and the differ-ences in the intensity of the mechanisms of ice porosity formation in different water areas can be one of the possible reasons for these variations. The water mass contains gases in two forms: gases dissolved in the water mass, as well as gas bubbles that are formed when wind waves break up, and bubbles that float up from the seabed. The article presents the results of the analysis of the role of each of these forms in the formation of gas inclusions (pores) into the crystal structure of ice. The estimates showed that the main source of gas pores in ice crystals is the gas bubbles coming to the surface from the bottom, formed during the decomposition of bottom sediments or during gas leaks from near-bottom oil and gas fields. The possibility of gas bubbles occurring and rising to the ice-water boundary depends on the presence of bottom sources of the gases, the intensity of dissolution of the bubbles and the depth of the water area. Therefore, the variation in the porosity and the strength of ice over the space of the water areas can be associated with the changes in their depths, and the presence and location of the natural gas sources.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

The conformations of trifluoroacetyl triflate, CF3C(O)OSO2CF3, were investigated through vibrational experimental methods (gas-phase FTIR, liquid-phase Raman, and Ar-matrix FTIR spectroscopy) and Density Functional Theory (DFT) calculations. A potential energy surface was computed using the B3P86 /6-31+g(d) approximation as a function of the dihedral angles τ1 = CCOS and τ2 = COSC. The surface reveals three minima, which were further optimized using the B3LYP method with various basis sets (6-31++G(d), 6-311++G(d), tzvp and cc-pvtz). The global minimum corresponds to a syn-anti conformer (the CO double bound syn with respect the O−S single bond and the C−O single bond anti with respect to de S−C single bond). The other two minima represent enantiomeric syn-gauche forms. The Ar-matrix FTIR spectrum exhibited clear evidence of the presence of two conformers. Furthermore, the randomization process observed following broad-band UV-visible irradiation facilitated the identification of the IR absorption of each conformer. Based on the Ar-matrix FTIR experiments, the vapour phase of trifluoroacetyl triflate at room temperatures was composed of approximately 60-70% of the syn-anti conformer and 30-40% of the syn-gauche form.

Developing a dependable gas and condensate value chain is vital for the ongoing prosperity of the oil and gas industries. To achieve this, NNPC is enhancing its production facilities by employing process modeling and simulation with the assistance of Symmetry iCON®. As a part of this initiative, a simulation model was created using the Symmetry iCON® pipe plexus solver to simulate the dynamic environment of the gas and condensate pipeline network in the Nigerian Southern region. To validate the model, data from a single month, specifically December 2022, was utilized. Furthermore, the algorithm was utilized to generate projections for the month of January 2023, providing valuable insights into its effectiveness. The study also highlighted the significance of accurately estimating the characteristics and properties of a pseudo component of C6+ in relation to thermodynamics and material properties, which was a particularly insightful finding. he assessment of this property has transitioned from being relatively unimportant to becoming critically important, primarily due to the lack of condensate data monitoring at specific terminals. However, it's worth noting that the model currently has an error margin of 4-6% when predicting the data. As more information becomes available in the future, the model can be easily fine-tuned to better align with the actual conditions, allowing for more accurate predictions.

Oil and Gas companies, both national and international, along with government regulators, share a common goal of efficiently managing their valuable assets. These assets refer to the Reserves of oil and Gas located underground. Typically, production and Reserves Engineers play a crucial role in managing these reserves through the implementation of well testing techniques. Thus far, the gold standard in this field has been to ensure the optimal management and utilization of these resources. In the context of well testing, the separator has traditionally been considered the gold standard. However, despite regulatory mandates for frequency of well testing (Such as the general requirements of every 30days in the Nigeria south East zone sector), There is a lack of specific regulations regarding the expected flow measurement uncertainties. This gap in the regulations leaves room for improvement in establishing guidelines for accurate flow measurements. This paper aim to Review the various test separator employed, examine the implications of the 30days testing interval under real - world conditions, and critically assess the achievable measurements uncertainties in the field. Additionally, it will provide a candid analysis that sheds light on the expected uncertainties associated with flow measurements. The introduction of the multiphase meters in the past two decades hold the potential for significant advancements in Reservoirs management performance. However, the authors suspect that this potential has not been universally realized. This paper aim to address this issue by examining the extent to which the benefits of multiphase meters have been effectively utilized in reservoir management. By doing so, it seeks to shed light on any existing gaps and propose recommendation for maximizing the impact of multiphase metres in the field. In addition to the aforementioned objectives, this paper will also address and explore the following key aspects:Identification and review of both the strength and weaknesses associated with test separators. By thoroughly examining these attributes, we can gain valuable insight into their effectiveness and potential areas for improvement. Exploration of alternative application of test separator and their impact on well testing efficiency. Real -World comparison will be provided to highlight the advantages and challenges associated with these alternative uses, offering a comprehensive understanding of their implications. Evaluation of the contribution that multiphase flows meters (MPFMs) can bring to the testing scenario and overall performance. By assessing the capabilities and potential benefits of MPFMs, we aim to provide a comprehensive picture of their role in enhancing testing procedures. Examination of the flow measurement uncertainties that can be expected from a test separator and their potential impact on reservoirs management performance. By understanding and quantifying these uncertainties, we can gain insight into how they may affect decision -making and optimization strategies in managing our materials assets effectively. Delving into the question of reconciling multiphase flow meter (MPFMs) with test separators. This analysis aims to inject a sense of realism into the world of managing our major material assets by explaining the challenges and opportunities associated with integrating and aligning these two measurement technologies. By addressing these crucial aspects, this paper strives to provide a comprehensive understanding of the complexities involved in managing our material assets, ultimately driving towards more informed decision-making and improved performance.

Methane is a greenhouse gas and identified as a key driver of near-term climate change. Bottom-up approaches estimate annual methane loss from US natural gas production and transport at 6 Tg, but recent studies suggest this may be an underestimate. To investigate this possibility, an equipment-based emissions inventory, using EPA emission factors, was developed to calculate methane emissions from oil and gas operations in the Delaware Basin, USA. Emission factors and activity data were then updated using contemporary and region-specific measurement data. The original inventory estimated emissions at 315 Gg CH4 y-1 (gas production-normalized rate of 0.6% loss), while the updated inventory estimated emissions of 1,500 Gg CH4 y-1 (2.8% loss). The largest changes resulted from large fugitive emissions from oil production (+430 Gg CH4 y-1), updating maintenance activity emissions (+214 Gg CH4 y-1), considering flaring inefficiency (+174 Gg CH4 y-1), and the inclusion of associated gas venting (+136 Gg CH4 y-1). This study suggests that a systematic underestimate probably exists in current bottom-up inventories and identifies sources currently missing or may be incorrect. We also strongly recommend that emission factors should be validated through direct comparison against measurement campaigns that include long-tail distributions typical of oil and gas activities.

Shrubs are a significant component of urban vegetation residing in parks, but they experience various influences of biotic and abiotic agents, among which aphids play an important role. In this work, the effect of aphid colonization on three shrub species in urban environment was examined. Fourteen parameters have been analyzed, describing photosynthetic pigment content and gas exchange to carbon, nitrogen, and hydrogen partition. While no significant effect of colonization was found on photosynthetic pigment parameters, the effect was significant on gas exchange parameters. The strongest effect aphid colonization achieved on nitrogen partition and C/N ratio, parameters that could be suggested in further similar studies. All parameters were classified in two groups according to principal component analysis, suggesting correlation between nitrogen and carbon content, C/N ratio, measured gas exchange parameters and chlorophyll a content. The ratio between net photosynthesis and dark respiration (A/K) was in the second group, suggesting that this parameter provide additional information on the effect of aphid colonization, and deserve special attention in further studies. There were differences in reaction of examined shrub species, where the strongest reaction by gross primary productivity (GPP) achieved Hybiscus syriacus, and by nitrogen partition and C/N ratio Spirea trilobata and Cydonia japonica.

A gas-hydrate method of CO₂ gas storage is one of the modern technology for reducing it emissions into the atmosphere. The breakup of gas bubbles by a shock wave is an actual area of scientific and technological research. However, it is little known that such research began in the late 1950s in the USSR. The article presents the main discoveries related to the destruction of gas bubbles in a liquid under the influence of a shock wave, made more than 60 years ago. Looking back: study the past to understand the present.

Several factors, such as internal algorithm, sensor technology, and obsolescence might skew outcomes when comparing different gas analysers measurements during CPET. Besides aerosol borne infectious disease are a source of contamination during cardiopulmonary exercise tests (CPET). Thus, the main aim of this study was to determine the agreement degree between the Quark RMR and the Jaeger Oxycon Pro, using an antibacterial filter with the latter. Forty-two participants (19-54 years old) performed two non-consecutive maximal graded exercise tests on a cycle-ergometer on two counterbalance and different days using the Oxycon Pro and the Quark RMR in a randomized order. Differences between devices were tested using a generalized linear model adjusted by Bonferroni, and correlation and agreement was assessed using Pearson’s correlation coefficient (R), intraclass coefficient correlation (ICC), Lin’s concordance correlation coefficient (CCC) and Bland-Altman plots. No significant differences were found between devices in any of metabolic or ventilatory parameters for cardiorespiratory fitness assessment (VO_2max: 3131.3±882.1 vs. 3189.8±894.8, p=0.071, VCO_2max: 3436.3±936.0 vs. 3550.3±1043.2, p=0.071, for Quark RMR and Oxycon Pro, respectively). However, Bland-Altman plots showed a trivial tendency towards Oxycon Pro overestimation relative to Quark RMR as air flow volume increases. Both devices showed strong correlation and high level of agreement during maximal and submaximal exercise intensities (Pearson’s R: 0.974 & 0.977; ICC: 0.985 & 0.987; Lin’s CCC: 0.971 & 0.974, for VO₂ and VCO₂, respectively). Therefore, providing consistency to CPET data comparison between both devices, and insight into whether the use of these metabolic carts could be interchangeable or combined when a single device cannot be used for CPET assessment.

The increase in carbon dioxide emissions has a significant impact on human society and the global environment. As the most abundant and cheap C1 resource, the conversion and utilization of carbon dioxide has received extensive attention from researchers. In many methods of carbon dioxide conversion and utilization, the reverse water gas conversion reaction is considered to be one of the most effective ways. In this paper, the research progress of reverse water gas conversion reaction in recent years is introduced.

Soluble noble metal salts are widely used for loading noble metals as nano-catalysts in many applications. In this paper, Pt-SnO2 composite nanoceramics were prepared from SnO2 nanoparticles and H2PtCl6 using two Pt-loading methods separately: For the solution reduction method, the H2PtCl6 solution was added to a suspension of SnO2 and zinc powder to form Pt on SnO2 nanoparticles; and for the impregnation method, Pt was formed from H2PtCl6 in the course of sintering. Although a series of samples prepared using both Pt loading methods showed a strong response to H2 at room temperature, the ones prepared using the solution reduction method exhibited much better room temperature hydrogen sensing characteristics. For two samples of 0.5 wt% Pt and sintered at 825°C, the response value for the sample prepared using the solution reduction method was 5300 to 1% H2-20% O2-N2, which was much larger than that of 150 for the sample prepared using the impregnation method. Samples prepared using the two Pt loading methods have similar microstructures as characterized by XRD, FESEM, EDS, TEM, and HRTEM. However, the residual chlorine content in those using the impregnation method was found to be higher than that using the solution reduction method through analysis. It is proposed that the striking difference in the room temperature hydrogen sensing characteristics among samples prepared using these two different Pt loading methods separately resulted from their different chlorine removal process. This study demonstrates the importance of a proper method in loading noble metals from their soluble salts as nano-catalysts in many applications.

Some of Iran's gas resources are known as sour gas because one of the major by-products of this gas is water. In fact, natural gas is combined with water vapor in underground reservoirs. In some areas, the amount of water vapor in natural gas is so high that it can be used as a source of drinking water. However, it should be noted that water vapor in natural gas may exacerbate corrosion in pipes and industrial equipment, and the combustion of more natural gas produces high temperatures that can lead to the production of nitrogen oxides (NOx), which They are the cause of air pollution. This is while the processed gas has a standard percentage composition in which the amount of water has the lowest position. The removal of moisture from natural gas is due to the need to prevent the reduction of the calorific value of the gas and also to purify the gas in order to achieve the necessary standards for delivering gas to petrochemicals, industries and domestic uses. The main goal of this research is to investigate the influencing parameters on zeolite TiO2 nanocomposite membranes in order to absorb moisture from gas. For this reason, with the construction of a TiZ-V membrane as a standard membrane, the result of the initial evaluation of a suitable membrane for gas dehumidification was made, and this membrane was placed as a standard for measuring the effect of the manufacturing parameters in a way that in each stage of membrane construction It was found that it was different from standard TiZ-V membrane only in terms of one parameter. This type of investigation made it possible to determine the effect of various effective parameters in membrane construction on efficiency. The findings showed that increasing the concentration of SiO2 has the greatest effect on increasing the water flux of the membrane. According to the other findings of this study, the effect of increasing the reaction time of the vapor phase carrier has been to reduce the process of paternity selectivity loss at higher pressures. Although due to the safety limitation of the equipment to measure the efficiency of the membrane at pressures higher than 7 bar, this measurement was not carried out, but charts were presented regarding the state of the water in the water, which were a measure of the superiority of the water in the water in comparison to the gas in the water, which is the higher water in the water It is an indicator of the appropriateness of the membrane's efficiency at its corresponding pressure, so that the examination of the difference between these two graphs shows the possibility of using the membrane at higher pressures

This work presents an LC resonant passive wireless gas sensor with a novel structure designed to mitigate the negative impact of substrate. The LC sensor antenna with the new structure and the reader antenna were designed and optimized utilizing HFSS software to improve the transfer efficiency. The superiority of the designed structure compared with the general ones is highlighted and verified. The change in the substrate capacitance has essentially no interference with the parameters to be measured of the LC sensor. The sensor with the new structure was prepared by combining etching and sputtering methods. The structure of the ZnO nanowires (NWs) was characterized to confirm their high purity and wurtzite crystal structure. The LC gas sensors demonstrated excellent wireless sensing performance including a low detection limit of 0.5 ppm NO2, high response of 1.058 and outstanding stability at 180 °C. The developed new sensor structure not only prevented interference from the substrate during gas sensing testing, but also expanded the choice of sensor substrates, playing a critical role in the development of sensors based on LC resonance principle.

Methane (CH4) emissions from agricultural sources make a significant contribution to the total anthropogenic greenhouse gas emissions that contribute to climate change. According to the International Panel on Climate Change (IPCC) guidelines for calculating greenhouse gas emissions, agriculture is responsible for approximately 10% of total CH4 emissions from anthropogenic sources. CH4 is mainly emitted from livestock farming, especially from cattle production during enteric fermentation and from manure. The article describes the results of multivariate statistical analyzes carried out on data collected in 1961–2020 based on the data for 30 countries with the largest cattle population. The trends of temporal changes in cattle population were evaluated and groups of countries with similar patterns in the study period were distinguished. Variables which are correlated with changes in the number of cattle were indicated. Forecasts of cattle population and CH4 emission related to cattle for the coming years are presented.

A total internal reflection photonic crystal fiber (PCF) based on hexagonal core is proposed for gas sensing in a specific wavelength range. The higher sensitivity and lower confinement loss were realized by the structure of the proposed PCF consists of two layers with circular holes rotated hexagonally around a core region and six slotted air-hole in the cladding based on numerical analysis. The simulation results show that the enhancement of the relative sensitivity has been done by enhancing the diameter of the hexagonal shape air-hole cladding (d1) and the hexagonal arranged holes around the central solid core (d0) in this design. Also, the confinement loss has been reduced by enhancing the ratio of length to width of slotted holes (l/w) and decreasing the cladding air-hole diameters (d1). As the refractive index increases, the wavelength shifts toward the long wavelength. And in a certain temperature range, the transmission characteristics of the device does not change with the temperature. The results are helpful for designing high performance PCF for gas sensing applications.

: We report on a direct correlation between macroscale structural variations and the gas sorption capacities of an ion gel. Here, we chose 1-ethyl-3-methylimidazolium bis(trifluoromethyl sulfonyl)imide ([Emim][TF2N]) and poly(vinylidene fluoride)-co-hexafluoropropylene (PVDF-HFP) as the ionic liquid and host polymer, respectively. The CO2 sorption in the thin films of IL-polymer was measured by the gravimetric method. The results of our experiment show that the trend of CO2 uptake of these mixtures is non-linearly correlated with the content of IL. Here we highlight the variation in the molecular structure of the polymers is the main reason behind the observed trend. The presented data suggest the possibility of using the composition of mixtures containing IL and polymers to realize a synergistic gain for gas sorption in these mixtures.

The previously developed models for fuel droplet heating and evaporation processes, mainly the Discrete Multi Component Model (DMCM), and Multi-Dimensional Quasi-Discrete Model (MDQDM) are investigated for the aerodynamic combustion simulation. The models have been recently improved, and generalised for a broad range of bio-fossil fuel blends so that the application areas are broadened with increased accuracy. The main distinctive features of these models are that they consider the impacts of species thermal conductivities and diffusivities within the droplets to account for the temperature gradient, transient diffusion of species and recirculation. A formulation of fuel surrogates is made, using the recently introduced model, referred to as ‘’Complex Fuel Surrogate Model (CFSM)’’ and analysing their heating, evaporation, and combustion characteristics. The CFSM is aimed to reduce the full composition of fuel to a much smaller number of components based on their mass fractions, and to formulate fuel surrogates. Such approach has provided a proof of concept with the implementation of the developed model into a commercial CFD code ANSYS-Fluent. A case study is made for the CFD modelling of gas-turbine engine using kerosene fuel surrogate. The surrogate is proposed using the CFSM. The model is implemented into ANSYS-Fluent via a user-defined function to provide the first full simulation of the combustion process. Detailed chemical mechanism is also implemented into ANSYS Chemkin for the combustion study.

Docked ships are a source of contamination for the city while they keep their engine working. Plumes emissions from large boats can carry a number of pollutants to the nearby cities causing a detrimental effect on the life quality and health of local citizens and ecosystems. A computational fluid dynamics model of the harbour area of Tromsø has been built in order to model the deposition of CO2 gas emitted by docked vessels within the city. The ground level distribution of the emitted gas has been obtained and the influence of the wind speed and direction, vessel chimney height, ambient temperature and exhaust gas temperature has been studied. The deposition range is found to be the largest when the wind speed is low. At high wind speeds, the deposition of pollutants along the wind direction is enhanced and spots of high pollutant concentration can be created. The simulation model is intended for the detailed study of the contamination in cities near the coast or an industrial pollutant source of any type of gas pollutants and can easily be extended for the study of particulate matter.