With proper processing and utilization, biofortified cassava may contribute to the nutritional status of the consumers, thus, the need for this study. High-quality cassava flour from white- (TME 419) and biofortified (TMS 01/1368) cassava varieties were produced at a commercial processing factory, after which the flour is composite with wheat flour to produce bread. The nutritional composition, physical properties and sensory quality of the composite bread were analyzed using standard methods. Results showed that composite bread from 20% biofortified cassava flour (20-YCF) had a higher value of total β-carotene (0.74 μg/g), moisture (37.83%) and ash (2.29%) contents. The fat (3.72%) and protein (12.83%) contents were higher in 20% white cassava flour (20-WCF) composite bread. The 20-YCF composite bread had the highest loaf volume (3286.2 cm3), elasticity (6.32), chewiness (40.51 N) and gumminess (6.41), 20-WCF composite bread had higher specific volume (3.59 cm3/g) and hardness (176.50 N). The 100% wheat bread had higher cohesiveness (0.10) and loaf weight (932.35 g). A significant negative correlation (r = - 0.98, p≤0.05) exist between bread hardness and protein content. The composite bread compared favourably with the 100% wheat bread in terms of weight and aroma, but, the 100% wheat bread was more acceptable.

Ga doped ZnO thin films were formed by the Ultrasonic Chemical Spray Pyrolysis method onto substrates using zinc acetate and gallium (III) nitrate hydrate as precursors. The structural, optical, surface and electrical properties were studied as a function of increasing Ga doping concentration from 0 to 6 at %. Structural studies were shown polycrystalline with a hexagonal crystal structure. The transparency in the visible range was around 85% for thin film deposited using 6 at % Ga doping. With the aim of determining surface images and surface roughness of the films atomic force microscope images were taken. Ga doping of ZnO thin films could markedly decrease surface roughness. Electrical resistivity was determined by four point method. The resistivity 2.0% Ga doped ZnO film was the lowest resistivity of 1.7 cm. In the photoluminescence measurements of the films, existence of UV and defect emission band was observed. As a result, Ga doped ZnO films have advanced properties and promising materials for solar cells.

Dye sensitized solar cell technology is having an important role in renewable energy research due to its features and low cost manufacturing processes. Devices based on this technology appear very well suited for integration into glazing systems due to their characteristics of transparency, color tuning and manufacturing directly on glass substrates. Field data of thermal and electrical characteristics of dye sensitized solar modules (DSM) are important since they can be used as input of building simulation models for the evaluation of their energy saving potential when integrated into buildings. However still few works in the literature provide this information. The study here presented wants to contribute to fill this gap providing a thermal and electrical characterization of a DSM in real operating conditions using a method developed in house. This method uses experimental data coming from test boxes exposed outdoor and dynamic simulation to provide thermal transmittance and solar heat gain coefficient (SHGC) of a DSM prototype. The device exhibits an U-value of 3.6 W/m²K, confirmed by an additional measurement carried on in the lab using a heat flux meter, and a SHGC of 0.2, value compliant with literature results. Electrical characterization evidences an increase of module power with respect to temperature causing DSM suitable for integration in building facades.

Micro satellites must survive severe mechanical conditions during their launch phase. Therefore, structural design requirements are imposed on the micro satellites. These requirements are the strength requirement and the stiffness requirement. Usually, the structural design of a micro satellite is performed using the internal stress analysis and the natural frequency analysis, which are based on a Finite Element Method (FEM). The validity of this structural design is evaluated through vibration tests. In an early stage of development, which has a FEM model of a satellite in the process of creation, presumption of the natural frequency of a satellite may be difficult. In this study, a simple method for determining the longitudinal and lateral minimum natural frequencies of the micro satellites during the ascent phase was clarified. The structure of the micro satellites used in this research is made of aluminum alloy, and they have a monocoque structure. The Young's modulus and moment of inertia of area used to calculate the minimum natural frequencies were determined using the area ratio of the monocoque structure to the entire satellite. When this method is used, the estimated minimum natural frequencies of the longitudinal direction and the lateral direction are in agreement with the measured values acquired by the vibration tests. In order to shorten the process of micro satellites development, this paper describes a practical estimation method of the minimum natural frequency for micro satellites.

The crystal structure of Pb₁₀(PO₄)₆O, the proposed matrix for the potential room-temperature superconductor LK-99, Pb_10-xCu_x(PO₄)₆O (x = 0.9-1.0), has been reinvestigated by single-crystal X-ray diffraction using crystals prepared by Merker and Wondratschek (The crystal structure is trigonal, P, a = 9.8109(6), c = 14.8403(12) Å, V = 1237.06(15), R₁ = 0.0413 using 3456 unique observed reflections. The crystal structure of Pb₁₀(PO₄)₆O is a superstructure with regard to the ‘standard’ P6₃/m apatite structure type. The doubling of the c parameter is induced by the ordering of ‘additional’ O’ atoms within the structure channels running parallel to the c axis and centered at (00z). The O’ atoms form short bonds to the Pb1 atoms, resulting in splitting the Pb1 site into two, Pb1A and Pb1B. The structural distortions are further transmitted to the Pb phosphate framework formed by four Pb2 sites and PO₄ groups. The structure data previously reported by Krivovichev and Burns (Z. Kristallogr. 2003, 218, 357-365) may either correspond to the Pb₁₀(PO₄)₆O_x(OH)_2-x (x ~ 0.4) member of the Pb₁₀(PO₄)₆O - Pb₁₀(PO₄)₆(OH)₂ solid solution series, or to the high-temperature polymorph of Pb₁₀(PO₄)₆O (with the phase with doubled c parameter being the low-temperature polymorph).

Nickel nitrate diammine, Ni(NH₃)₂(NO₃)₂, can be synthesised from the thermal decomposition of the nickel nitrate hexammine, Ni[(NH₃)₆](NO₃)₂. The hexammine decomposes in 2 distinct steps; the first releases 4 equivalents of ammonia while the second involves the release of NO_x, N₂ and H₂O to yield NiO. The intermediate diammine compound can be isolated following the first deammoniation step or synthesised as a single phase from the hexammine under vacuum. Powder X-ray diffraction (PXD) experiments have allowed the structure of Ni(NH₃)₂(NO₃)₂ to be solved for the first time. The compound crystallises in orthorhombic space group Pca2₁ (a = 11.0628 (5) Å, b = 6.0454 (3) Å, c = 9.3526 (4) Å; Z = 4) and contains 11 non-hydrogen atoms in the asymmetric unit. Fourier Transform Infrared (FTIR) spectroscopy demonstrates that the bonding in the ammine is consistent with the structure determined by PXD.

A monocular vision pose estimation and identification algorithm used on a small spacecraft for future orbital servicing is studied in this paper. A tracker spacecraft equipped with a short-range vision system is proposed to recover the 3D structural model of a space target in orbit and automatically identify its solar panels and main body using only visual information from an onboard camera. The proposed reconstruction and identification framework is tested using structure-from-motion and point cloud identification methods. The Efficient Perspective-n-Points (EPnP) descriptor is used for pose estimation. Triangulated points are used for component segmentation by means of orientation histogram descriptors. Experimental results based on laboratory images of a spacecraft model show the effectiveness and robustness of our approach.

In this article we review the advances that have been made on the understanding of the high-pressure structural, vibrational, and electronic properties of wolframite-type oxides since the first works in the early 1990s. Mainly tungstates, which are the best known wolframites, but also tantalates and niobates, with an isomorphic ambient-pressure wolframite structure, have been included in this review. Apart from estimating the bulk moduli of all known wolframites; the cation-oxygen bond distances and their change with pressure have been correlated with their compressibility. The composition variations of all wolframites have been employed to understand their different structural phase transitions to post-wolframite structures as a response to high pressure. The number of Raman modes and band gap energy changes have been also analyzed in the basis of these compositional differences. The reviewed results are relevant for both fundamental science and for the development of wolframites as scintillating detectors. The possible next research venues of wolframites have also been evaluated.

A La2FeCrO6 (LFCO) double perovskite powders were synthesized by hydrothermal method, which crystallized in an orthorhombic (Pnma) structure and exhibited a spherical morphology with average particle size of 900 nm. Fourier transformation infrared spectroscopy confirmed the octahedral coordination of Fe and Cr ions in the powders. XPS spectra revealed dual oxide states of Fe (Fe2+/Fe3+) and Cr (Cr3+/Cr4+) elements, and oxygen element appeared as lattice oxygen and defect oxygen, respectively. The LFCO powders exhibit ferromagnetic behavior at 5 K with saturation magnetization of 0.31 μB/f.u., coercive field of 8.0 kOe, and Curie temperature of 200 K. Griffiths phase appeared in the powders between 200 K and 223 K. The LFCO ceramics displayed a butterfly-like magnetoresistance (MR)-magnetic field (H) curve at 5 K with MR (5 K, 6 T) value of -4.07%. Temperature dependence of resistivity of the LFCO ceramics demonstrated their semiconducting nature. Electrical transport data were fitted by different conduction models. Strong frequency dispersion dielectric behavior was observed in the LFCO ceramics. A dielectric abnormality observed around 260 K, was ascribed to the jumping of electrons trapped in shallow levels created by oxygen vacancies. The dielectric relaxation behavior exhibited by dielectric loss between 160 K and 260 K, was contributed to the singly-ionized oxygen vacancies.

One of the major limitations of the current 3D-concrete-printing technology is incorporation of reinforcement. Furthermore, there is a need to decrease the ecological footprint of printable concrete. As a possible solution for these challenges, this paper presents a 3D-printable strain-hardening geopolymer composite (3DP-SHGC) that shows pseudo-ductile behaviour under direct tension. The developed 3DP-SHGC is composed of one-part (just-add-water) geopolymer binder made of slag (GGBFS), fly ash (FA) and solid activator. The one-part geopolymer binder eliminates the need for elevated temperature curing and handling of corrosive alkaline liquids. At first, an optimum matrix was identified by studying the effects of FA to GGBFS ratio on the rheological properties and compressive strength. Subsequently the optimum matrix was reinforced by PVA fibres to make the 3DP-SHGC, which printing performance and rheological properties were evaluated. In addition, the influences of curing temperature on the compressive, flexural and tensile performances of the printed specimens were also investigated. The results were compared with those obtained for the mould-cast specimens. The 3DP-SHGC exhibited superior flexural performance, higher tensile strength, and comparable tensile strain capacity to the mould-cast counterpart. Further, the curing temperature had influence on the mechanical properties of both 3D-printed and mould-cast SHGCs. The underlying reasons for the differences are discussed.

This study explores the capital structure determinants of Korean firms over an extensive period (1995-2021), encompassing both stable and crisis conditions. Employing a dynamic panel data model and the Generalized Method of Moments (GMM) estimation, we address the endogeneity issue introduced by the inclusion of lagged dependent variables. Our research integrates firm-specific internal factors with macroeconomic external variables to provide a comprehensive understanding of the influence of varying economic environments on capital structure. Our study suggests that in times of economic stability, the capital structure decisions of a firm are more influenced by internal factors such as profitability. However, in periods of economic downturns, it's the external macroeconomic market conditions that tend to have a greater impact on these decisions. It's also noteworthy that both book leverage (BL) and market leverage (ML) exhibit quicker adjustments during stable periods as opposed to periods of crisis. This indicates a higher agility of firms in adapting their capital structures in stable normal conditions. Our findings contribute to existing literature by offering a holistic view of capital structure determinants in Korean firms. They underscore the necessity of adaptable financial strategies that account for both internal dynamics and external economic conditions. This study fills a gap in current research, presenting new insights into the dynamics of capital structure in Korean firms and suggesting a multifaceted approach to understanding capital structure in diverse economic contexts.

The prevalence of internet gaming disorders (IGD) is considerably high among youth, especially with social isolation imposed by the ongoing COVID-19 pandemic. IGD adversely affects mental health, quality of life, and academic performance. The Internet Gaming Disorder Scale (IGDS9-SF) is designed to detect IGD according to DSM-IV diagnostic criteria. However, inconsistent results are reported on its capacity to diagnose IGD evenly across different cultures. To ensure the suitability of the IGDS9-SF as a global measure of IGD, this study examined the psychometric properties of the IGDS9-SF in a sample of Sri Lankan university students (N = 322, mean age =17.2 ± 0.6, range = 16-18 years, 56.5% males) and evaluated its measurement invariance across samples from Sri Lanka, Turkey, Australia, and the USA. Among Sri Lankan students, a unidimensional structure expressed good fit, invariance across different groups (e.g., gender, ethnicity, and income), adequate criterion validity (strong correlation with motives of internet gaming, daily gaming duration, and sleep quality), and good reliability (alpha = 0.81). Males and online multiplayers expressed higher IGD levels, greater time spent gaming, and more endorsement of gaming motives (e.g., Social and Coping) than females and offline players. Across countries, the IGDS9-SF was invariant at the configural, metric, and scalar levels, albeit strict invariance was not maintained. The lowest and highest IGD levels were reported among Turkish and American respondents, respectively. In conclusion, the IGDS9-SF can be reliably used to measure IGD among Sri Lankan youth. Because the scale holds scalar invariance across countries, its scores can be used to compare IGD levels in the studied countries.

The aim of the present study was to describe and determine changes in the superelastic properties of NiTi archwires after clinical use and sterilization. Ten archwires from five different manufacturers (GAC, 3M, ODS, GC, FOR) were cut in two segments and evaluated using a three-point bending test in accordance with ISO 14841:2006. The centre of each segment was deflected to 3.1mm and then unloaded to 0 N to obtain a load-deflection curve. Deflection at the end of the plateau and forces at 3, 2, 1 and 0.5mm on the unloading curve were recorded. Plateau slopes were calculated at 2, 1 and 0.5mm of deflection. Data obtained were statistically analysed to determine differences (p<0.001). Results showed that the degree of superelasticity and exerted forces differed significantly among brand groups. After three months of clinical use, FOR released a greater force for a longer activation period. GC, EURO and FOR archwires seemed to lose their mechanical properties. GC wires released more force than other brand wires after clinical use. Regarding superelasticity after sterilization, GAC, 3M and FOR wires recovered their properties, while EURO archwires lost more.

We present a numerical illumination model to calculate direct as well as diffuse or Hapke scattered radiation scenarios on arbitrary planetary surfaces. This includes small body surfaces such as main belt asteroids as well as e.g. the lunar surface. The model is based on the raytracing method. This method is not restricted to spherical or ellipsiodal shapes but digital terrain data of arbitrary spatial resolution can be fed into the model. Solar radiation is the source of direct radiation, wavelength-dependent effects (e.g. albedo) can be accounted for. Mutual illumination of individual bodies in implemented (e.g. in binary or multiple systems) as well as self-illumination (e.g. crater floors by crater walls) by diffuse or Hapke radiation. The model is validated by statistical methods. A χ2 test is undertaken to compare simnulated images with DAWN images acquired during the survey phase at small body 4 Vesta.

Mechanical response of bisphenol-F based epoxy cured with amine hardener was investigated in tensile testing. Different types of methods were considered in preparing the tensile samples in order to evaluate their effects on the tensile strength of the cured epoxy system. Specifically, four types of preparation methods were discussed to prepare the tensile samples were considered in the study. Further, the effect of different type of tensile samples on tensile strength of specimens was also considered in the analysis. The experimental results showed that the preparation methods affected the tensile strength of the specimens. Starting from the experimental results, an appropriate testing methodology is proposed for epoxy based nanocomposite composite specimens in order to reduce problems that may arise during the test and to optimize procedures for preparation of specimens.

Measurements of optical properties have been used for decades to study particle distributions in the ocean. They have been found useful to constrain suspended mass concentration as well as particle-related properties such as size, composition, packing (particle porosity or density) and settling velocity. Optical properties, however, provide measurements that are biased, as certain particles (based on size, composition, shape or packing) contribute to a specific property more than others. Here we study this issue both theoretically as well as by contrasting different optical properties collected simultaneously in a bottom boundary layer, to highlight the utility of such measurements as well as the biases we are likely to encounter using different optical properties to study suspended particles. In particular, we investigate the possibility to infer settling velocity from vertical profiles of optical measurements, finding that the effects of aggregation dynamics can seldom be ignored.

The pomegranate, an ancient plant native to Central Asia, cultivated in different geographical areas including the Mediterranean basin and California, consists of flowers, roots, fruits and leaves. Presently, it is utilized not only for the exterior appearance of its fruit but above all, for the nutritional and health characteristics of the various parts composing this last one (carpellary membranes, arils, seeds and bark). The fruit, the pomegranate, is rich in numerous chemical compounds (flavonoids, ellagitannins, proanthocyanidins, mineral salts, vitamins, lipids, organic acids) of high biological and nutraceutical value that make it the object of study for many research groups, particularly in the pharmaceutical sector. Its interest is mainly addressed to the knowledge of its biological and functional properties and the research of new formulations to apply it in a wide range of diseases such as neoplastic, cardiovascular, viral, inflammatory, metabolic, microbial, intestinal, reproductive and skin diseases. In this review we highlight the health-promoting properties of pomegranate and its bioactive compounds against human diseases.

That form and function relates, is the maxim to anatomy and physiology. Yet form-function relations can be difficult to establish. Human subjects with excessive trabeculated myocardium in the left ventricle, for example, are diagnosed with non-compaction cardiomyopathy, but the extent of trabeculations may be without relation to ejection fraction. Rather than rejecting a relation between form and function, we may ask whether the salient function is assessed; is there a relation to electrical propagation, mean arterial blood pressure, propensity to form blood clots, or all? And how should extent of trabeculated muscle be assessed? While reviewing literature on trabeculated muscle, we applied Tinbergen’s four types of causation - how does it work, why does it work, how is it made, and why did it evolve - to better parse what is meant by form and function. The paper is structured around cases that highlight advantages and pitfalls of applying Tinbergen’s questions. It further uses the evolution of lunglessness in amphibians to argue lung reduction can impact on chamber septation, and it considers the evolution of an arterial outflow in fishes to argue that reductions in energy consumption may drive structural changes with little consequences to function. Concerning trabeculations, we argue they relate to pump function in the embryo in the couple of weeks before the onset of coronary circulation. In fetal and postnatal stages, a spectrum of trabeculated-to-compact myocardium makes no difference to cardiac function and in this period form and function may appear unrelated.

Porous structures and micropatterning surfaces play a crucial role in the development of highly sensitive force sensors. However, achieving these two conductive architectures typically requires complex materials synthesis and expensive manufacturing processes. In this study, we introduce a novel conductive composite film featuring a porous/micropyramid hybrid conductive architecture, which is achieved through a straightforward process of materials mixing and one-step screen printing. By utilizing a deep eutectic solvent in the ink component, micropores are induced in the printed composite, while the mesh of the screen mask acts as a template, resulting in a micropyramid film surface. We have successfully realized highly sensitive flexible force sensors with multifunctional capabilities for perceiving normal force and shear force.

The cuttlebone-like structure is a complex porous bionic structure with asymmetric sinusoidal S-shaped wall structure connecting laminar septa, and studies have shown that the cuttlebone-like structure has light weight, high strength and excellent energy absorption capability. It has become an important research to investigate the mechanical mechanism of cuttlebone-like structure and to design a bionic structure beyond nature structure based on it. In order to investigate the mechanical properties of the static compression and shearing processes of the cuttlebone-like structure, this paper establishes theoretical formulas and analyzes the influence of dimensionless parameters such as height-to-thickness ratio $\lambda$, period-to-thickness ratio $\xi$ and amplitude to period ratio $\eta$ on the compression and shearing processes with the help of ABAQUS finite element software.The parameter sensitivity analysis method was used to compare the important influence degree of each dimensionless parameter on the mechanical properties of the structure and to determine the relative optimal parameters of the structural mechanical properties under compression and shearing. Based on the relatively optimal parameter of the cuttlebone-like structure, the cross-sectional geometry of the structure is improved to build a new cuttlebone-like structure.The experimental results showed that the new cuttlebone-like structure with revised cross-section improved the mechanical properties of the cuttlebone-like structure.The study results are of theoretical guidance to enhance the mechanical properties and geometric design of cuttlebone-like structures.

Most fully developed galaxies have vivid spiral structure, but the formation and evolution of spiral structure is still a mystery that is not fully understood in astrophysics. We find that the currently used equations of galactic dynamics contain some unreasonable components. In this paper, the following three working assumptions are introduced to simplify the galactic structural equations. 1. In the research of large-scale structure, the retarded potential of the gravitational field should be taken into account. The propagating time of the gravitational field from center to border is longer than the revolution periods of the stars near the center of galaxy. Newton's gravitational potential is unreasonable for such case, and the weak field and low velocity approximation of Einstein's field equation should be adopted. 2. The stars in a fully developed galaxy should be zero-pressure and inviscid fluid, and the equation of motion is different from that of ordinary continuum mechanics. Stars move along geodesics. 3. The structure of the galaxy is only related to the total mass density distribution. The equation of state of dark halo is different from that of ordinary luminous interstellar matter, so their trajectories are also very different. Dark halo and ordinary matter in galaxy are automatically separated. The total mass density distribution can be presupposed according to the observation data, and then it can be determined by comparing the solution of the equations with the observed data. These assumptions and treatments are supported by theory and observation. The variables of the equations of simplified galactic dynamics are separated from each other, and the equations are well-posed and can be solved according to a definite procedure. Therefore, this simplified dynamic equation system provides a more reasonable and practical framework for the further study of galactic structure, and can solve many practical problems. Besides, it is closely related to the study of dark energy and dark matter.

Sequential properties can violate Bell-type inequalities without direct influence on each other, but only if detected in pairs. This is demonstrated below with theoretical arguments, and with a straightforward toy model. Rotating arrows can have transient qualities that produce maximal Bell violations with predetermined values. Any non-signaling phenomenon (classical, or non-classical) can also be interpreted as local.

In recent decades, perovskite-type compounds (ABB′O3) have been exhaustively studied due to their unique ferroelectric properties. In this work, a systematic study aiming to prepare fine particles in the binary system SrZrO₃–SrTiO₃ was conducted under hydrothermal conditions in a KOH (5 M) solution at 200 °C for 4 h under a constant stirring speed of 130 rpm. The precursors employed were SrSO₄ powder (< 38 μm size) and coprecipitated hydrous gels of Zr(OH)₄•9.64 H₂O (Zr-gel) and Ti(OH)₄•4.5H₂O (Ti-gel), which were mixed according to the stoichiometry of the SrZr_1-xTixO₃ in the compositional range of 0.0>x>100.0 mol% Ti⁴⁺. The XRD results revealed the formation of two crystalline phases rich in Zr⁴⁺, an orthorhombic structured SrZr0.93Ti0.07O3 and a cubic structured SrZr0.75Ti0.25O3 within the compositional range of 0.1–0.5 mol of Ti4+. A cubic perovskite-structured solid solution, SrTi1-xZrxO3, was preferentially formed within the compositional range of 0.5>x>0.1 mol% Ti⁴⁺. The SrZrO₃ and SrZr_0.93Ti_0.07O₃-rich phases had particle sizes averaging 3 m with a cubic morphology. However, a remarkable reduction in the particle size occurred on solid solutions prepared with hydrous Ti-gel over contents of 15 mol% Ti⁴⁺ in the reaction media, resulting in the formation of nanosized particles agglomerates with cuboidal shape self-assembled via a 3D hierarchical architecture, the sizes of these particles varied in the range between 141.0–175.5 nm. The limited coarsening of the particles is discussed based on the Zr-gel and Ti-gel dehydration capability differences that occurred under hydrothermal processing.

Alunogen, Al2(SO4)3·17H2O, occurs as an efflorescent in acid mine drainage, low-temperature fumarolic or pseudofumarolic (at coal fires) terrestrial environments. It is considered as one of the main Al-sulfates of Martian soils demanding comprehensive crystal chemical data of natural terrestrial samples. However, structural studies of natural alunogen were carried out in 1970s without localization of H atoms and have not previously been performed for samples from geothermal fields, despite the fact that these environments are considered as proxies of the Martian conditions. The studied alunogen sample comes from Verkhne-Koshelevsky geothermal field (Koshelev volcano, Kamchatka, Russia). Its chemical formula is somewhat dehydrated, Al2(SO4)3×15.8 H2O. The crystal structure was solved and refined to R1 = 0.068 based on 5112 unique observed reflections with I > 2σ(I). Alunogen crystalizes in P-1 space group, a = 7.4194(3), b = 26.9763(9), c = 6.0549(2) Å, α = 90.043(3), β = 97.703(3), γ = 91.673(3) °, V = 1200.41(7) Å3, Z = 2. The crystal structure consists of isolated SO4 tetrahedra, Al(H2O)6 octahedra and H2O molecules connected by hydrogen bonds. The structure refinement includes Al, S and O positions that are similar to previous structure determinations and thirty-four H positions localized for the natural sample first. The study also shows the absence of isomorphic substitutions in the composition of alunogen despite the iron-enriched environment of mineral crystallization. The variability of the alunogen crystal structure is reflected in the number of “zeolite” H2O molecules and their splitting. The structure complexity of alunogen and its modifications ranges from 333-346 bits/cell for models with non-localized H atoms to 783-828 bits/cell for models with localized H atoms. The higher values correspond to higher hydration state of alunogen.

Utilization of Bidirectional Reflectance Distribution Function (BRDF) model parameters obtained from the multi-angular remote sensing is one of the approaches for the retrieval of vegetation structural information. In this research, the potential of multi-angular vegetation indices, formulated by the combination of multi-spectral reflectance from different view angles, for the retrieval of forest above ground biomass was assessed. This research was implemented in the New England region with the availability of a high quality forest inventory database. The multi-angular vegetation indices were generated by the simulation of the Moderate Resolution Imaging Spectroradiometer (MODIS) BRDF/Albedo Model Parameters Product (MCD43A1 Version 6) based BRDF parameters. The effects of seasonal (spring, summer, autumn, and winter) composites of the multi-angular vegetation indices on above ground biomass, angular relationship of the spectral reflectance with above ground biomass, and the interrelationships between the multi-angular vegetation indices were analyzed. Among the existing multi-angular vegetation indices, only the Nadir BRDF-adjusted NDVI ( and Hot-spot incorporated NDVI ( showed significant relationship (more than 50%) with the above ground biomass. This research proposed two more sensitive vegetation structural indices, Fore-scattering Back-scattering NDVI and Vegetation Structure Index (VSI). The Fore-scattering Back-scattering NDVI showed higher sensitivity (R² = 0.62, RMSE = 52.46) towards the above ground biomass than existing multi-angular vegetation indices. Furthermore, the VSI performed in the most efficient way explaining 64% variation of the above ground biomass, suggesting that the right choice of the spectral channel and observation geometry should be considered for improving the estimates of the above ground biomass. In addition, the right choice of seasonal data (summer) was found to be important for estimating the forest biomass while other seasonal data were either insensitive or pointless. The promising results shown by the VSI suggest that it could be an appropriate candidate for monitoring vegetation structure from the multi-angular satellite remote sensing.

Nanotechnology sparks discussions and concerns about the impacts of new nanomaterials on health and the environment. It holds importance in various domains due to its unique struc-tures. Carbon dots (C-dots) are versatile nanomaterials with applications in bioimaging, sensing, catalysis, polymers, solar cells, and more. They offer desirable characteristics such as stability, cost-effectiveness, biocompatibility, and high photoluminescent quantum yield. C-dots have the potential to replace expensive fluorophores in solar cells. They are catego-rized as carbon quantum dots, graphene quantum dots, and carbonized polymer dots. C-dots have outstanding optical and photoelectric properties with low toxicity. Bottom-up and top-down approaches are used for the synthesis of carbon dots (CDs), with each method im-pacting their physicochemical characteristics. The choice of synthesis method depends on de-sired properties and application requirements. Researchers combine these methods and ex-plore new approaches to enhance synthesis efficiency and tailor CD properties. CDs have di-verse chemical structures with modified oxygen, polymer-based, or amino groups on their surface. Various characterization methods such as HRTEM, XPS, and optical analysis (PL, UV) are used to determine CD structure. Carbon dots (CDs) are cutting-edge fluorescent nano-materials with remarkable qualities such as biocompatibility, low toxicity, environmental friendliness, high water solubility, and photo-stability. They are easily adjustable in terms of their optical properties, making them highly versatile in various fields. CDs find applications in bio-imaging, nanomedicine, drug delivery, solar cells, LEDs, photo-catalysis, elec-tro-catalysis, and other related areas.

Background: The Perceived Inventory of Technological Competency as Caring in Nursing (PITCCN) questionnaire has been designed to measure technological competency as caring in nursing practice. As there were no psychometrically sound instruments to quantify the concept in the Slovene language. The goal was to assess the level of psychometric properties of the PITCCN investigated in Slovene hospitals. Methods: Content validity was conducted with eight experts and quantified by the content validity index (CVI) and the modified Cohen’s kappa index. Face validity was assessed through discussions with participants from the target culture in the pilot study. To assess construct validity and internal consistency, a cross-sectional research methodology was used on a convenience sample of 121 nursing personnel from four hospitals. Principal component analysis (PCA) was used to examine construct validity, while Cronbach’s alpha and adjusted item-total correlations were used to measure internal consistency. Results: The content and face validity of PITCCN were adequate. The scale validity index (S-CVI) was 0.97. Cronbach’s α was 0.92, and subscale reliabilities ranged from 0.810 to 0.925. PCA showed four components, which explained more than 73.49% of the variance. Conclusions: The Slovenian version of PITCCN (PITCCN_SI) has good psychometric properties.

In Summer 2017, huge wildfires in the British Columbia region (Canada) led to the injection of a remarkably high concentration of biomass burning aerosol in the atmosphere. These aerosol masses reached the city of Naples, Italy, since the end of August 2017, where they were characterized by means of a multiwavelength lidar and a sun-sky-lunar photometer. Here we report on the optical and microphysical properties of this aerosol in an intriguing condition, occurring on 4th September 2017, which is characterized by an interesting multi-layered vertical distribution of the aerosol. The Lidar profiles highlighted the presence of four aerosol layers, with two located in the lower troposphere and other two at stratospheric altitudes. A rather thorough characterization of the biomass burning aerosol was carried out. The aerosol depolarization ratio showed an increasing dependence on the altitude with averaged values of 2-4% for the tropospheric layers, which are indicative of almost spherical smoke particles, and larger values in the stratospheric layers, suggestive of aspheric particles. Lidar-derived size distributions were retrieved for the first three aerosol layers, highlighting a higher particle concentration in the fine mode fraction for the layers observed at higher altitude. A dominance of fine particles in the atmosphere (Fine Mode Fraction > 0.8) with low absorption properties (absorption AOD < 0.0025 and SSA > 0.97) was also observed over the whole atmospheric column by sun-photometer data. The space-resolved results provided by the lidar data are consistent with the columnar features retrieved by the AERONET sun-photometer, thus evidencing the reliability and capability of lidar characterization of atmospheric aerosol in a very interesting condition of multiple aerosol layers originating from Canadian fires overpassing the observation station.

The Individual Work Performance Questionnaire (IWPQ) can be defined as the individual be-haviour capable of generating value and competitive advantage for the organization. It is a mul-ti-dimensional construct, consisting of task performance, contextual performance and counter-productive work behavior. Albeit important, a comprehensive measure of individual job per-formance is still lacking in the Italian context. This paper describes the validation of an Italian adaptation of the IWPQ. A back translation procedure was used. To investigate the psychometric properties of the 18-item Italian IWPQ, 1053 participants (502 men, 47.7%; 551 women, 52.3%) were enrolled; the age of participants ranged between 19 and 69 (Mage=34.6, SD= 11.8), and for the oc-cupation, the sample is classified in blue collar 32.5%, pink collar 33% and white collar 34.5%. Exploratory and confirmatory factor analyses and multigroup confirmatory factor analyses were performed to test the structural factor of the IWPQ. The results supported the goodness of the IWPQ in the Italian context and the scales were found consistent with the original structure. One item was omitted due to a low factor loading, resulting in a final 17-item structure. Multigroup confirmatory factor analysis showed that the factor solution was invariant across both gender and occupational category and found evidence of metric invariance, uniqueness and scalar invariance, and structural invariance. Convergent and discriminant validity were also tested and showed.

In the aerospace sector, structural and non-structural components are usually subjected to a wide range of environmental conditions. Although lightweight, the use of composite parts for these applications is restricted, due to their poor performance in severe environmental conditions. Specifically, moisture can seriously damage the materials' performance, reducing their mechan-ical, thermal, electrical, and physical properties as well as the service time. A strategy to improve the materials’ resistance in humid environments is the use of protective lightweight barrier coatings to reduce the diffusion of gases and/or liquids in composites. Nanolamellar nanocom-posite characterized by the high in-plane orientation of nanoplatelets effectively works as barrier structures by generating tortuous paths for molecule diffusion. In this work, the effectiveness of protection against water uptake of nanocomposites reinforced with Graphite NanoPlatelets (GNPs) at high filler content (70, 80 and 90%wt) for Kevlar sandwich panels of a nacelle engine of an ATR42 aircraft has been investigated. Moisture uptake and Ground Air Ground (GAG) tests were carried out in an environmental chamber to reproduce temperature and relative humidity profiles representative of a real-scale application for a regional aircraft composite part. The high filler content of the graphene films ensures a high level of tortuosity by delaying and reducing moisture absorption by –71% compared to the unprotected panel, showing good barrier properties.

The influence of various energetic particles and electron injection on transport of minority carriers and non-equilibrium carrier recombination in Ga₂O₃ is summarized in this review. In Ga₂O₃ semiconductor, if robust p-type material and bipolar structures become available, diffusion length of minority carriers will be of critical significance. Diffusion length of minority carriers dictates functionality of such electronic devices as diodes, transistors, and detectors. One of the problems in ultra-wide band gap materials technology, is the short carrier diffusion length, due to scattering on extended defects. Electron injection in n- and p-type Gallium Oxide results in a significant increase of the diffusion length, even after its deterioration due to exposure to alpha- and proton-irradiation. Furthermore, post electron injection diffusion length in irradiated material exceeds that in Ga₂O₃ prior to irradiation and injection. The root cause of the electron injection-induced effect is attributed to the increase of minority carrier lifetime in the material due to trapping of non-equilibrium electrons on native point defects. It is, therefore, concluded that the electron injection is capable of “healing” the adverse impact of radiation in Ga₂O₃ and can be used for control of minority carrier transport and, therefore, device performance.

This work seeks to approach the comparative analysis of the distribution of POFs (polymeric optical fibers) arranged in a random and sorted manner in the manufacture of translucent concretes. The following characteristics were analyzed: compressive strength, flexural tensile strength, capillary water absorption and light transmittance. Portland cement, water, fine aggregate (sand), silica fume, polycarboxylate ether-based superplasticizer and polymeric optical fiber were used in the production of the composites. Except the fiber content, the mixture of all other inputs was kept as a fixed parameter. Groups with the following levels of POFs were produced: 0%, 2%, 3.5% and 5%. The POF content is the sum of the areas of the fiber sections in the composite with the total area of the translucent surface. The results showed that for the analysis of mechanical behavior (flexural tensile and compressive strength) and durability (capillary water absorption), composites with random and sorted fibers within the 2% POF presented to belong to statistically distinct groups. For the other fiber contents, there was no pattern of behavior, that is, it cannot be said that there is a difference within 3.5% or 5% POF between sorted and random fibers in relation to the mechanical and durability characteristics analyzed. As for the light transmittance, it was attributed that the statistical difference between the fiber arrangements only within the 5% POF content can be a consequence of their accumulation in certain points of the material, thus influencing this characteristic measured by a light meter.

Geotechnical investigation is an important site characterization process in engineering construction. Excavation pits and boreholes are popular geotechnical investigation methods for accessing subsurface soil and rock characteristics. Although they are accurate, they are limited to the discrete locations where tests are carried out. The demand for 3D representation has been increasing as an alternative for improved visualization of geotechnical investigations. This study developed a procedure for 3D modelling of geotechnical investigations using open-source software. It improves 3D visualization of geotechnical investigations and characterization of accuracy and uncertainty assessment. Presently, most geotechnical investigations do not regularly report uncertainty assessment despite its importance in risk analysis of the investigations. The procedure developed in this study was tested in a proposed site for construction of an Inland Container Depot where it depicted geotechnical soil properties with more than 80% accuracy on holdout samples. It was able to model both horizontal and vertical variations of the soil properties with quantification of uncertainty. More testing and wide applications are recommended.

The effect of graphene oxide (GO) on mechanical strengths and durability of cement composites has been studied by preparing GO-modified cement mortars. Thermogravimetric analysis (TGA) and nuclear magnetic resonance (29Si MAS-NMR) were performed on the cement paste to research the influence of GO on the hydration process and chain structure of calcium-silicate-hydrate (C-S-H) gels. In addition, mechanical strength test, such as compressive and flexural, were performed on cement mortars. The addition of GO at 0.05 wt.% (by weight of cement) increased the compressive strength by 9.02% after 28 days. Furthermore, the flexural strength of cement mortars with 0.05 wt.% GO and superplasticizer (SP) after 7 and 28 days increased by 12.26% and 21.86%, respectively, compared with reference mortar. At the same time, the effect of GO proved to be more significant and effective in the durability tests, suggesting that GO can enhance the microstructure through hydration products to create a highly cross-linked micro structure.

The main goal of this study was to introduce glycerol as a plasticizer to Polyvinyl Alcohol (PVA) membranes in order to increase their flexibility. The qualities of PVA membranes produced with various glycerol concentrations were evaluated. With the modified PVA membranes containing 5% glycerol, encouraging results were obtained. These membranes had superb optical characteristics and a 90% transmittance rate. This shows that the membranes are suited for applications needing excellent optical clarity since they permit light to travel through with little distortion. Importantly, FTIR analysis demonstrated that the addition of glycerol had no effect on the PVA membranes' chemical composition or structural integrity. In comparison to pure PVA Membrane, the modified membranes' water barrier qualities showed a considerable drop of up to 50%. The membranes are useful for applications requiring moisture management or breathability because of the decline, which points to an increase in permeability to water vapour. The large increase in flexibility, which was achieved by the PVA membranes containing 5% glycerol and beyond the brittleness typically associated with pure PVA, was a noteworthy discovery. The possible applications are expanded due to the increased flexibility, especially in industries where adaptability and flexibility are essential. Additionally, the addition of glycerol improved the thermal stability of the membranes, as they showed increased resistance to breakdown or decomposition at high temperatures. Additionally, the modified membranes' mechanical qualities were better than those of pure PVA, indicating that the glycerol addition improved their overall mechanical performance and tensile strength. PVA membranes were effectively made more flexible by adding 5% glycerol as a plasticizer. This led to membranes with superior optical qualities, reduced water barrier properties, greater flexibility, improved thermal stability, and maybe improved mechanical capabilities. These discoveries open up new opportunities for the use of these flexible PVA membranes in a range of settings, such as flexible packaging, biomedical materials, and other industries that need adaptive and flexible materials.

The temperature-dependent energy storage properties of four tungsten bronze phase compounds are studied together with an investigation of their structure and temperature-dependent permittivity response, i.e., Ba6Ti2Nb8O30 (BTN), Ba6Zr2Nb8O30 (BZN), Sr3TiNb4O15 (STN) and Sr3ZrNb4O15 (SZN) ceramics. It was found that BZN has smaller grains and a more porous structure than BTN. SZN shows no clear grain boundaries with the most porous structure among all samples, exhibiting a much lower permittivity response than other samples with no signs of phase transitions from room temperature to 400 °C. Though the energy storage response of those samples is generally quite low, it exhibits rather good temperature stability. It was suggested that by obtaining a denser structure through chemical modification or other methods, those tungsten bronze ceramics with good temperature stability could be promising as energy storage devices when improved energy storage properties are achieved.

Concrete production requires a significant amount of natural resources, with aggregates comprising between 55% and 80% of the total volume. However, over-exploitation of natural aggregates has led to the exploration of alternative materials for use in concrete production. In this study, crushed hazelnut shells were investigated as a partial replacement for fine aggregate, addressing the problem of natural resource depletion and offering a second use for this important agricultural waste product available in Chile. Hazelnut shells were incorporated in percentages of 2.5%, 5%, and 10% by weight of sand for water-cement ratios of 0.4 and 0.5. The compressive strengths at 7 and 28 days and bending tensile strengths at 28 days were determined, alongside physical properties such as workability, temperature, air content, fresh density, and hardened density of the concrete. Our findings show that replacing 2.5% of the fine aggregate with hazelnut shells led to higher compressive strength at 28 days, exceeding the strength of the standard specimens by 9.5%, whereas replacing 5% of the fine aggregate led to the highest bending tensile strength, exceeding the resistance of the standard specimens by 3.5%. Moreover, the 0.4 w/c ratio consistently led to better results for both compressive and bending tensile resistances, with fewer and lower reductions in mechanical resistances compared to the standard mixture. Our results suggest that concrete mixes with hazelnut shells as a replacement for fine aggregate at a percentage of up to 2.5% can be used in constructive systems with compression strengths lower than 17 MPa, and mixtures with up to 10% hazelnut shell replacement can be used in structures with tensile bending stress requirements lower than 6 MPa. Overall, the use of hazelnut shells as a partial replacement for fine aggregate in concrete production presents an environmentally-friendly and cost-effective solution for the construction industry.

Deformation behavior of the composite "hen's eggshell - polymer plomb" under bending is examined. Polymer coating does not change the type of behavior of the composite based on eggshell that continues to be brittle despite the mechanical characteristics of the composite could vary in wide limits for brittle structure. Joining "hen's eggshell – polymer plomb" never crack under loading and, hence, it exhibits the high cohesion strength under stresses applied in these experiments. It seems that the composite "hen's eggshell - polymer plomb" could apply as the substitution of the composite "tooth enamel - polymer plomb" under elaboration of novel restorative materials for dentistry, namely, for estimation of their mechanical properties including cohesive strength.

In this study, the Bohler K 190 steel was used. The steel was manufactured by the powder metallurgy (PM) process. The boronizing process was carried out in the range of 1173 to 1323 K, for 1-10 h. The samples were boronized in solid medium, called the Durborid powder mixture. For the microstructural observations, the scanning electron microscopy was utilized for determining the morphology of interfaces and measuring the layers’ thicknesses. The phase composition of boride layers was also determined with X-ray diffraction analysis. To investigate the redistribution of chemical elements redistribution during the boronizing process, the EDS mapping and EDS point analysis were used. The boride layers were constituted by FeB and Fe2B phases except for 1173 K for 1 h. The values of Vickers microhardness of Fe2B, FeB and transition zone were estimated. Finally, to assess the boron activation energies in FeB and Fe2B, the so-called integral method was applied and the results in terms of activation energies were confronted with the literature data.

The study of the inherent factors that influence the isolation of one type of metallosupramolecular architecture over another is one of the main objectives in the field of Metallosupramolecular Chemistry. In this work, we report two new neutral copper(II) helicates, [Cu2(L1)2]·4CH3CN and [Cu2(L2)2]·CH3CN, obtained by means of an electrochemical methodology and derived from two Schiff-based strands functionalized with ortho- and para-t-butyl groups on the aromatic surface. These small modifications let us to explore the relationship between the ligand design and the structure of the extended metallosupramolecular architecture. The magnetic properties of the Cu(II) helicates were explored by EPR spectroscopy and DC magnetic susceptibility measurements.

ZrO2-YO1.5-TaO2.5(ZYTO) composite ceramic is considered to be the candidate of next generation of thermal barrier coatings as its excellent thermal stability and low thermal conductivity in high temperature, however, the mechanical properties and fracture tougheness of ZYTO system may be the shortcomings compared with the 8YSZ. In this study, ZYTO composite ceramics were successfully prepared by chemical coprecipitation reaction, the microsture of resulting composites were studied as a function of doping of M-YTaO4. Mechanical properties, including the density, porosity, hardness and Young's modulus, are determinate; the toughening mechanism were verified by the crack growth behavior of Vickers indentation test Results suggested that M-YTaO4 refines the fluorite phase grain and strengthens the grain interface in the composite ceramic. The thermal mismatch between the second phase and matrix produces residual stress in the bulk and affects the crack propagation behavior. With the increase of M-YTaO4 doping, the grain coarsening and ferroelastic domains are observed in the experiments. The ferroelastic domains with orthogonal polarization directions near crack tip evidences the ferroelastic toughening mechanism. The competition among these crack behaviors, such as cracks deflection, bridging and bifurcation, dominates the actual fracture toughness of the composite. The best toughening formula is determinate in the two-phase region and the highest fracture toughness is about to 3.1MPa·m1/2. Above all, mechanical properties of ZYTO composite ceramics look potential for thermal barrier coatings materials.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

PurposeThis study was designed to characterize the psychometric properties of the Persian version of the Fear of Hospitalization Scale (P-FHS).Design and methodsIn order to evaluate the validity and reliability of the translated scale, a cross-sectional design was employed. Ten experts evaluated the content validity of the Fear of Hospitalization Scale (FHS) after it had been back-translated into Persian. With 612 patients having emergency surgery, construct validity was assessed using exploratory factor analysis (EFA) and confirmatory factor analysis (CFA). The STROBE checklist for cross-sectional studies was followed.FindingsThe results of EFA (n = 306) showed that the fear of hospitalization had three factors. These three factors accounted for 45.28% of the total variance. Also, these factors were confirmed by CFA (n = 306) (root-mean-square error of approximation = (90%. confidence interval) = 0.050 [0.041, 0.058], goodness-of-fit index = 0.945, comparative fit index = 0.968, Non-Normal Fit Index = 0.948, incremental fit index = 0.968, Tucker-Lewis Index = 0.959). The coefficients of Cronbach’s alpha, McDonald’s omega, composite reliability, and maximum reliability for all three factors were greater than 0.7, demonstrating satisfied internal consistency.Practice implicationAccording to the published results, the P-FHS is effective at measuring hospitalization anxiety in patients undergoing emergency surgery. It is advised that nurses in Iranian culture use a legitimate and trustworthy technique to pinpoint the causes of hospitalization anxiety in patients undergoing emergency surgery to give optimal care.

Ultrasonic based inspection of thin-walled structures often requires prior knowledge of their mechanical properties. Their accurate estimation could be achieved in a non-destructive manner employing, e.g., elastic guided waves. Such procedures require efficient approaches for experimental data extraction and processing, which is still a challenging task. An advanced automated technique for material properties identification of an elastic waveguide is proposed in this investigation. It relies on the information on dispersion characteristics of guided waves, which are extracted by applying the matrix pencil method to the measurements obtained via laser Doppler vibrometry. Two objective functions have been successfully tested, and the advantages of both approaches are discussed (accuracy vs computational costs). The numerical analysis employing the synthetic data generated via the mathematical model as well as experimental data shows that both approaches are stable and accurate. The influence of the presence of various modes in the extracted data is investigated. One can conclude that the influence of the corruptions related to the extraction of dispersion curves is not critical if the majority of guided waves propagating in the considered frequency range are presented. Possible extensions of the proposed technique for damaged and multi-layered structures are also discussed.

Usually in the manufacture of beer by fermentation of barley, in both industrialized and developing countries significant amounts of organic solid waste are produced from barley straw. These possibly have an impact on the carbon footprint with an effect on global warming. According to this, it is important to reduce environmental impact of these solid residues, and an adequate way is the recycling using them as raw material for the elaboration of handmade paper. Therefore, it is required to manage this type of waste by analyzing the environmental impact, and thus be able to identify sustainable practices for the treatment of this food waste, evaluating its life cycle, which is a useful methodology to estimate said environmental impacts. It is because of this work shows the main results obtained using the life cycle analysis (LCA) methodology, to evaluate the possible environmental impacts during the waste treatment of a brewery located in the state of Hidalgo, Mexico. The residues evaluated were barley straw, malt residues and spent grain, and at the end, barley straw was selected to determine in detail its environmental impact and its reuse, the sheets analyzed presented a grammage that varies from 66 g/m2 and 143 g/m2, resistance to burst was 117 to 145 kpa, with a crystallinity of 34.4% to 37.1%.

During composting process, soils undergo many changes in their physical, chemical and biological properties. Composting has been widely known as an aerobic process during which organic matter is decomposed to humus like substances broken into many organic materials or compounds. The project aims to compare and analyze different combination of composting that yield different properties and nature of soils, and testing their soil physical properties. Dug three compost pits each 1.5 m in depth, labeled compost pit A consisting of potato peels – the only kitchen waste most common around the college hostels, compost pit B consisting of leaf litter and other garden trimmings and compost pit C consisting of cow dung and the other as a controlled experiment with no composting practices.

Nowadays, the massive use of tires generates large stocks of waste material which is a serious environmental problem. The usual method used for processing wasted tires is mechanical crushing, in which fiber, steel, and rubber are separated. The aim of this research is the recycling of the obtained rubber, called also GTR (Ground Waste Tires). With this purpose, the paper analyses the mechanical properties of the composites produced by mixing GTR with several industrial polymers. These composites are characterized by the percentage of GTR in the composite and its particle size. These two variables along with seven industrial polymers define a set of composites from which the mechanical properties are analyzed and presented. From the results, it can be drawn that this proposal could be a way to enhance some polymer properties and to contribute in some way to reduce the environmental wasted tires problem.

The thermal properties of novel nanomaterials play a significant role in determining the performance of the material in technological applications. Herein, direct measurement of the temperature diffusivity of cellulose nanocomposite films was carried out by the micro-contact method. Polymer films containing up to 2%wt. of nanocellulose were synthesised by a simple chemical process. Films of a high optical transmittance T ≈ 80 % (for a 200- μ m-thick film), which were up to 44% crystalline, were characterised. Two different modalities of temperature diffusivity based on: 1) a resistance change and 2) micro-thermocouple detected modulation of a heat wave, were used for the polymer films with cross-sections of ∼ 100 μ m thickness. Twice different in-plane α ‖ and out-of-plane α ⊥ temperature diffusivities were directly determined with high fidelity: α ‖ = 2 . 12 × 10 − 7 m 2 /s and α ⊥ = 1 . 13 × 10 − 7 m 2 /s. An amorphous polyethylene terephthalate (PET) fiber was measured for comparison α ‖ = 1 . 15 × 10 − 7 m 2 /s. This work provides an example of a direct contact measurement of thermal properties of nanocellulose composite films. The thermal diffusivity, which is usually high in strongly interconnected networks and crystals, was investigated for the first time in this composite.

In-situ grown C_0.3N_0.7Ti and SiC, which derived from non-oxide additives Ti₃SiC₂, are proposed to densify silicon nitride (Si₃N₄) ceramics with enhanced mechanical performance. Remarkable increase of density from 79.20% to 95.48% could be achieved for Si₃N₄ ceramics with 5vol% Ti₃SiC₂. The capillarity of decomposed Si from Ti₃SiC₂, and in-situ reaction between nonstoichiometric TiC_x and Si₃N₄ were believed to be responsible for densification of Si₃N₄ ceramics. An obvious enhancement of flexural strength and fracture toughness for Ti₃SiC₂ doped Si₃N₄ ceramics was observed. The maximum flexural strength of 795 MPa for Si₃N₄ composites with 5vol% Ti₃SiC₂ and maximum fracture toughness of 6.97 MPa^.m^1/2 for Si₃N₄ composites with 20vol% Ti₃SiC₂ are achieved when mixed powders are hot-press sintered at 1700℃. Pull out of elongated Si₃N₄ grains, crack bridging, crack branching and crack deflection were demonstrated to dominate enhance fracture toughness of Si₃N₄ composites.

The preparation and thermal properties of polypropylene foils, filled with ceramic microparticles, talc or boron nitride, are described. A slow, linear increase of thermal conductivity with volume percent of filler up to 30 vol % is detected. Reduction of the foil thickness bellow 200 micrometers leads to a significant increase of thermal conductivity. Specific thermal capacities of foils are temperature dependent, they decrease with filler incorporation.

Even if silicon alkoxides (especially ethylsilicates) have long been used as consolidants of weathered stone monuments, their physical properties are not ideal. In this study, an innovative procedure for the consolidation of sedimentary rocks was developed that combines the use of organometallic and alkylamine catalysts with the addition of well-defined nanoparticles exhibiting a narrow size distribution centered at ca 10 nm. As a suitable test material, the Pietra di Lecce limestone was selected because of its color and problematic physico-chemical properties, such as rather low hardness. Using the developed procedure, the mechanical and surface properties of the limestone were improved without the unwanted over-consolidation of the surface layers of the stone, and any significant deterioration in the pore size distribution, water vapor permeability or the stone’s appearance. The developed modified ethylsilicates penetrated deeper into the pore structure of the stone than the unmodified ones and increased the hardness of the treated material. The formed xerogels within the stone pores did not crack. Importantly, they did not significantly alter the natural characteristics of the stone.

: The effect that the microstructure exerts on the TRIP phenomenon and on the mechanical properties in a multiphase steel was studied. Samples of an initially cold-rolled ferrite-pearlite steel underwent different intercritical annealing treatments at 750 °C until an equal fractions of austenite/ferrite was reached; the intercritical treatment was followed by isothermal bainitic treatments before cooling the samples to room temperature. Samples in the first treatment were heated directly to the intercritical temperature, whereas other samples were heated to either 900 or 1100 °C to obtain a fully homogenized, single phase austenitic microstructure prior to the conducting the intercritical treatment. The high temperature homogenization of austenite resulted in the decrease in its stability, so a considerable austenite fraction transformed into martensite by cooling to room temperature after the bainitic heat treatment. Most of the retained austenite transformed during the tensile tests, and as a consequence, the previously homogenized steels showed the highest UTS. In turn, the steel with a ferritic-pearlitic initial microstructure, exhibited higher ductility than the other steels and texture components that favor forming processes.

Nanofibers appearing functional properties show a great promise as allowing constituents for a wide range of medical applications. In this work, Polycaprolactone (PCL), Silver Nitrate (AgNO₃) and Zinc Oxide (ZnO) were used for fabrication of nanofiber composite material by co-axial electrospinning (CAE) process. 5, 10, and 15 wt. % concentrations of PCL were utilized and different amount of AgNO₃ and ZnO were used in entire samples. Morphological analyses of the electrospun nanocomposites were done by scanning electron microscopy (SEM) and AgNO₃, ZnO and PCL materials’ functional groups were determined by Fourier Transform Infrared Spectroscopy (FTIR). Before co-axial electrospinning, physical properties such as liquid state ac conductivity, density and viscosity were measured for all solutions. Capacitance (C_p) and D-factors (tanδ) of nanocomposite materials are measured for the frequency range of 20Hz – 3MHz and the solid state alternating current (ac) conductivity, permittivity (ε’) and dielectric loss (ε’’) were calculated for all solutions after co-axial electrospinning. Effects of concentration percentages of PCL and AgNO₃ on real and imaginary parts of dielectric constant and solid state ac conductivity have been analyzed and comparisons have been made by the results obtained.

This paper examines the effect of the aggregate type on concrete strength and more specifically how the petrographic characteristics of various aggregate rocks as well as their physico-mechanical properties influences the durability of C 25/30 strength class concrete. The studied aggregate rocks are derived from Veria-Naousa and Edessa ophiolitic complexes as well as granodiorite and albitite rocks from their surrounding areas in central Macedonia (Greece). Concretes are produced with constant volume proportions, workability, mixing and curing conditions using different sizes of each aggregate type. Aggregates were mixed both in dry and water saturated states in concretes. Six different types of aggregates were examined and classified in three district groups according to their physicomechanical properties, petrographic characteristics and surface texture. The classification in groups after the concrete compressive strength test verified the initial classification in the same three groups. Group I (ultramafic rocks) presents the lowest concrete strengths, depending on their high alteration degree and the low mechanical properties of ultramafic aggregates. Group II (mafic rocks and granodiorite) presents a wide range of concrete strengths, depending on different petrographic characteristics and mechanical properties. Group III (albite rocks) presents the highest concrete strengths, depending on their lowest alteration degree and their highest mechanical properties. Therefore mineralogy and microstructure of the coarse aggregates affects the final strength of the concrete specimens.

Regenerated silk (RS) is a protein-based “biopolymer” that enables the design of new materials; here, we called “bionic” the process of regenerated silk production by a fermentation-assisted method. Based on yeast’s fermentation, here we produced a living hybrid composite made of regenerated silk nanofibrils and a single-cell fungi, the Saccharomyces cerevisiae yeast extract, by fermentation of such microorganisms at room temperature in a dissolution bath of silkworm silk fibers. The fermentation-based processing enhances the beta-sheet content of the RS, corresponding to a reduction in water permeability and CO₂ diffusion through RS/yeast thin films enabling the fabrication of a mechanically robust film that enhances food storage durability. Finally, a transfer print method, which consists of transferring RS and RS/yeast film layers onto a self-adherent paraffin substrate, was used for the realization of heat-responsive wrinkles by exploiting the high thermal expansion of the paraffin substrate that regulates the applied strain, resulting in a switchable coating morphology from the wrinkle-free state to a wrinkled state if the food temperature overcomes a designed threshold. We envision that such efficient and smart coatings can be applied for the realization of smart packaging that, through such a temperature-sensing mechanism, can be used to control food storage conditions.

Selected by in vitro techniques (SELEX, cell-SELEX), aptamers are strands of DNA or RNA molecules able to bind a wide range of targets, from small molecules to live cells, and even tissues, with high affinity and specificity. Due to their efficient targeting ability, aptamers are extensively used in different fields of applications. For example, they ensure high performance as cancer-related markers or in recognizing cancer cells. Actually, they represent a promising way for early diagnosis (biosensors) and to deliver imaging agents and drugs, in both cancer imaging and therapy (therapeutic aptamers). Aptamer-based biosensors (aptasensors) have attracted particular attention over the last decades, so as the possibility of using aptamers in disease therapy in substitution of monoclonal antibodies. The paper briefly reviews the most recent literature on this topic, both concerning the advances in biomedical applications and in the development of electrical aptasensors. The investigation concerning the bioelectronics features of aptamers, to be implemented in the development of electrical nanobiosensors, is also reviewed. To this aim, some recent results of a theoretical/computational framework for modelling the electrical properties of biomolecules (Proteotronics) are reported.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

The shear factor of ore drawing is one of the important factors affecting the formation of underground debris flow, and it has an important contribution to the formation of underground debris flow. The purpose of this paper is to study the effect of mining shear factor on underground debris flow in natural caving method. Based on the research background of the underground debris flow in Plan copper mine, this paper analyzes the characteristics of the slurry material structure of the underground debris flow, the influence of drawing shear factor on formation mechanism of underground debris flow is analyzed. The results show that the slurry of the underground debris flow in Plan mine is not only a pseudoplastic fluid but also a thixotropic fluid. It is indicated that once there is shearing force in drawing, it will deform, and its viscosity will decrease with the increase of shear rate and time. It is considered that the shear force produced by the flow of ore particles first produces shear action on the paste in the shear boundary region of ore drawing, it is reduced in viscosity and increased in fluidity, so that its “Activation” and then become a flowable paste, along with the bulk ore flow through the mouth. The continuous ore drawing process will continuously shear the new moraine slurry in the ore drawing channel and continuously “Activate” the moraine slurry in the ore drawing channel, finally, a certain scale and destructive down-hole debris flow accident. This paper is the first to study the effect of ore drawing shear factor on the formation mechanism of underground debris flow. It not only broadens the research field of debris flow, but also fills up the deficiency of systematic research on underground debris flow, and provides theoretical guidance for the prevention and control of underground debris flow.

Hepatitis C virus (HCV) is a major medical health burden and leading cause of chronic liver disease and cancer worldwide. More than 58 million people are chronically infected with HCV, with 1.5 million new infections occurring each year. An effective HCV vaccine is a major public health and medical need as recognized by the World Health Organization. However, due to the high variability of the virus and its ability to escape the immune response, HCV rapidly accumulates mutations making a vaccine a formidable challenge. An effective vaccine must elicit broadly neutralizing antibodies (bnAbs) in a consistent fashion. After decades of studies from basic research through clinical development, the antigen of choice is considered to be the E1E2 envelope glycoprotein due to conserved, broadly neutralizing antigenic domains located in the constituent subunits of E1, E2, and the E1E2 heterodimeric complex itself. The challenge has been elicitation of robust humoral and cellular responses leading to broad virus neutralization due to the relatively low immunogenicity of this antigen. In view of this challenge, structure-based vaccine design approaches to stabilize key antigenic domains have been hampered due to the lack of E1E2 atomic-level resolution structures to guide them. Another challenge has been development of a delivery platform in which a multivalent form of the antigen can be presented in order to elicit a more robust anti-HCV immune response. Recent nanoparticle vaccines are gaining prominence in the field due to their ability to facilitate a controlled multivalent presentation and trafficking to lymph nodes, where they can interact with both the cellular and humoral components of the immune system. This review focuses on recent advances in understanding the E1E2 heterodimeric structure to facilitate a rational design approach and the potential for development of a multivalent nanoparticle-based HCV E1E2 vaccine. Both aspects are considered important in the development of an effective HCV vaccine that can effectively address viral diversity and escape.

Soil structure is a sensitive and dynamic soil physical property which responds rapidly to different tillage systems, and thus it requires constant monitoring and evaluation. The visual evaluation of soil structure (VESS) and subsoil visual evaluation of soil structure (SubVESS) methods were used to assess the soil structure quality of clayey soils subjected to different tillage systems. The tillage systems were no-tillage (NT), conventional tillage (CT) and virgin land (VG). The study was conducted at Tshivhilwi and Dzingane in Thohoyandou, Vhembe District, Limpopo Province, South Africa. The NT system was practised for 8 and 40+ years at Tshivhilwi and Dzingahe, respectively. The results showed no impact of tillage system on both VESS and SubVESS at Tshivhilwi. The soil structure quality at Tshivhilwi as determined by VESS and SubVESS were found to be poor. However, at Dzingahe, both the VESS and SubVESS responded to the impact of tillage. At Dzingahe VESS showed a fair (Sq = 2.25) soil structural quality in the NT system, poor (Sq = 3.57) in the CT system and moderately poor (Sq = 3.05) in the VG. Similarly, at the same location the SubVESS scores were moderately good in the NT system, moderately poor for CT system and fair in the VG. The differences in the response of the VESS and SubVESS at the two locations were attributed to the differences in the duration at which the NT systems were practised. The VESS and SubVESS results were supported by selected measured soil physicochemical properties such as bulk density and porosity. In conclusion, the findings of this study showed that the VESS and SubVESS were able to effectively differentiate the impact of tillage systems on soil structural quality in clayey soils where NT was practised for a long period (40+ years) while it could not where NT was practised for a few years (8 years).

Multipactor is a common discharge phenomenon occurred in space microwave systems. The surface microstructure has been verified to be effective to mitigate multipactor. In this work, we design a square coaxial low-pass filter (SCLPF) with dielectric sheets loaded to check the multipactor dependence on the structure parameters of the loaded dielectric sheets, and further model groove structures on the sensitive area surface to lower the risk of multipactor. Simulation results indicate that the SCLPF loaded with alumina and PTFE exhibits good operational characteristics, and the multipactor threshold is significantly improved after introducing the surface grooves. Then we investigate the effects of three typical groove parameters, groove depth, groove number, and aspect ratio, on the multipactor threshold of the SCLPF device. The results show that the multipactor threshold raise at first as the groove number and groove depth increase, and then the threshold reaches a saturation status. For a deeper analysis of multipactor, we discuss how the grooves shelter the secondary electrons, and further mitigate the electron avalanche. Furthermore, the mechanisms of threshold saturation under the effect of groove parameters are analyzed in detail, and a contour map for the multipactor threshold of PTFE-loaded SCLPFs is given, which makes significant sense for predicting the multipactor threshold of the devices with its sensitive surface being grooved. The regularity of modulating the multipactor threshold by the groove structures obtained in this study is of engineering significance for suppressing multipactor in microwave devices in practical applications.

With the rapid development of the Internet industry, the problem of information overload has arisen due to the abundance of information available online. Recommendation algorithms, as the core of recommendation systems, have been attracting much attention and are a hot topic of research for many experts and scholars. The classical recommendation algorithms are mainly divided into three major categories: collaborative filtering recommendation algorithms, content-based recommendation algorithms, and hybrid-based recommendation algorithms. Although these algorithms are widely used in various fields, with the proliferation of information, these traditional recommendation algorithms are no longer able to meet the needs of the times. To address this issue, recommendation systems have been developed to provide users with personalized and relevant information or products. Despite the wide use of recommendation algorithms, such as collaborative filtering, content-based filtering, and hybrid approaches, traditional recommendation algorithms have limitations and are no longer suitable for meeting the demands of the times. This paper proposes a new recommendation algorithm, SFRRG, that fuses structure and feature information in graph neural networks to improve the performance of the recommendation system in rating prediction. The effectiveness of the proposed algorithm is demonstrated through experiments on various data sets and compared with existing recommendation algorithms.

The determination of the three-dimensional structure is a key step for the identification of new targets as well as the rational design of bioactive compounds. Herein, we report the synthesis and the structural elucidation of novel tetrameric macrocycles. Measurements were taken in solid and solution states with the help of X-ray scattering and NMR spectroscopy. The investigations made will help to find diverse applications for this new, promising compound class.

Due to the vast conformational space proteins can adopt, accurate and efficient prediction of protein structure remains still a challenging task, coupled with the intricacies of interatomic interactions and the limitations of current computational models in effectively navigating this complex molecular landscape. Additionally, the lack of comprehensive experimental data for all protein structures further exacerbates the difficulty in reliable machine learning-based prediction of the three-dimensional conformations of the proteios building block of life. Geometrically, Cartesian coordinate system (CCS, X, Y and Z) and spherical coordinate system (SCS, ρ, θ and φ) are two interconvertible coordinate systems, and are like two sides of one coin. Since the beginning of Protein Data Bank (PDB) in 1971, CCS has been the default approach to specify atomic positions with X, Y and Z in PDB. In this manuscript, therefore, I present a novel method for the reversible spherical geometric conversion of protein backbone structure coordinate matrices to three independent vectors: ρ, θ and φ. This reversible conversion facilitates lossless extraction of essential structural features from protein backbone structural data, enabling the development of advanced novel algorithms for protein structure prediction in future. In short, this inter-atomic SCS approach offers a comprehensive yet efficient means of representing protein backbone geometry, leveraging spherical coordinates to capture spatial relationships in a compact and intuitive inter-atomic manner, and to provide a robust framework for reversible feature extraction for the ongoing efforts in advancing the field of protein structure prediction, the holy grail of computational structural biology.

This paper introduces an innovative approach to numerically model Structure-Soil-Structure Interaction (SSSI) by integrating the Boundary Element Method (BEM) and the Finite Element Method (FEM) in a coupled manner. To assess the accuracy of the proposed method, a comparative study is undertaken, comparing its outcomes with those generated by the conventional FEM technique. Alongside accuracy, the computational efficiency aspect is crucial for the analysis of large-scale SSSI problems. Hence, the computational performance of the coupled BEM-FEM method undergoes a thorough examination and is compared with that of the standalone FEM method. The results from these comparisons illustrate the superior capabilities of the proposed method in comparison to the FEM method. The novel approach provides more reliable results compared to traditional FEM methods, serving as a valuable tool for engineers and researchers involved in structural analysis and design.

This paper investigates the hydroelastic responses of offshore floating solar photovoltaic farms (OFPVs) to minimize structural motion. The OFPV usually occupies a large sea space in the order of hectares and due to its huge structural length-to-thickness ratio, the structural deformation under wave action has to be taken into consideration. The flexible deformation of the structure under hydrodynamic loading is termed the hydroelastic response. Due to the relatively long structural length with respect to the encountering wavelength, the diffraction and radiation of waves have to be taken into account to accurately represent the hydrodynamic loadings on the floating platform. The numerical model is first validated by comparing the eigenvalues and eigenvectors of the OFPV obtained from the proposed numerical scheme with their counterparts obtained from an established finite element software. This is followed by the investigation of the hydroelastic response of various OFPVs designed in varying layout configurations. The various layout configurations are obtained by altering the floating modular units’ dimensions as well as the spacing of the OFPVs when deployed adjacent to each other. The optimal configuration that gives the best performance in terms of the overall smallest response, known as compliance, is then suggested. The results suggest that a longish OFPV layout has a lower hydroelastic response and the motion could be further reduced by increasing the global flexural stiffness via layout arrangement.

In this research, a design method for the graded triply periodic minimal surface (TPMS) structures with lightweight, high-strength, and high sound absorption properties is proposed. The graded TPMS structures are controlled by linear, quadratic, and sine functions. Uniform TPMS and graded TPMS were manufactured by laser powder bed fusion (LPBF) with AlSi7Mg powder, and an acoustic impedance tube test, compression test, and digital image correlation (DIC) test were ap-plied to obtain the sound absorption and compression properties. The sound absorption coefficient of a uniform Gyroid increases as the number of layers and surface thickness increase, and it in-creases as element size decreases. The sound absorption peak shifts to low frequencies as the number of layers increases. The sound absorption property of Type-Ⅰ graded TPMS is superior to the Type-Ⅱ, and the G-LinearⅠ has the highest sound absorption properties among the three functions. It reveals that the graded TPMS has superior sound absorption performance at low and medium frequencies. The compression and DIC results of graded TPMS also show excellent mechanical properties and energy absorption characteristics.

By taking advantage of a stability criterion established recently, the critical temperature T_c is reckoned with help of the microscopic parameters, characterising the normal and superconducting electrons, namely the independent-electron band structure and a repulsive two-electron force. The emphasis is laid on the sharp T_c dependence upon electron concentration and inter-electron coupling, which might offer a practical route toward higher T_c values and help to understand why high-T_c compounds exhibit such remarkable properties.

In the Standard Model of elementary particles, the rest mass, magnetic moment and electric charge of the electron are considered to be natural constants. In this article it is proposed that these properties can be calculated in a simple way from the corresponding Planck units using the well-known period doubling phenomenon in nonlinear dynamical systems. Periods corresponding to the values of the electron and positron properties belong to a subset of stable periods. The periodic structures of the rest energy and magnetic moment consist of three internal degrees of freedom, whereas the Coulomb energy of the electric charge consists of four. The number of period doublings for the elementary charge determines the value of the fine structure constant alpha.

Transient flows result in unbalanced forces and high pressure in pipelines. Under these conditions, the combined effects of flow-induced forces along with sudden pipe displacements can create cracks in the pipeline, especially at the junctions. This situation consequently results in water leakage and reduced operational efficiency of the pipeline. In this study, displacements and stresses in a buried pressurized water transmission pipe installed by pipe jacking method are investigated using numerical modeling and considering interactions between fluid, pipe, and soil. The analyses were performed consecutively under no-flow, steady flow, and transient flow conditions, in order to investigate the effects of flow conditions on displacements and stresses in the system. Analyses of the results show that displacements and stresses in the jointed concrete pipes are significant under transient flow conditions. Moreover, because of pressure transient effects, maximum tensile stresses exceed the tensile strength of concrete at the junctions, leading to cracks and consequent water leakage.

Reducing meat consumption is better for the environment. Unfortunately, commercial plant-based meat substitutes are often more expensive than meat and thus have not seen widespread adoption. This paper analyzes commercially-available spirulina, soy, pea, and brown rice protein isolates characteristics to provide data for non-meat protein cost reductions. Thermal and rheological properties, viscosity, density, and particle size distribution are analyzed for further study on alternative protein-based food processing. Differential scanning calorimetry analysis produced dry amorphous-shaped curves and paste curves with a more distinct endothermic peak. Extracted linear temperature ranges for processing in food production for spirulina was 70-90ºC; soy protein was 87-116ºC; pea protein was 67-77ºC; and brown rice protein was 87-97ºC. Viscosity analysis determined each protein material was shear-thinning and that viscosity increased with decreased water concentration, with rice being an exception to the latter trend. The obtained viscosity range for spirulina was 15,100-78,000cP; soy protein was 3,200-80,000cP; pea protein was 1,400-32,700cP; and brown rice protein was 600-3,500cP. The results indicate that extrusion is a viable method for further processing of the protein isolates as this technique has a large temperature operating range and variable screw speed. Data provided here can be used to make single or multi-component protein substitutes.

The design of biomaterial platforms able to release bioactive molecules is mandatory in tissue repair and regenerative medicine. In this context, electrospinning is a user-friendly, versatile and low-cost technique, able to process different kinds of materials in micro- and nano-fibers with a large surface area-to-volume ratio for an optimal release of gaseous signalling molecules. Recently, the antioxidant and anti-inflammatory properties of the endogenous gasotramsmitter hydrogen sulfide (H2S), as well as its ability to stimulate relevant biochemical processes on the growth of mesenchymal stem cells (MSC), have been investigated. Therefore, in this work, new poly(lactic) acid fibrous membranes (PFM), doped and functionalized with H2S slow-releasing donors extracted from garlic, were synthetized. These innovative H2S-releasing mats were characterized for their morphological, thermal, mechanical and biological properties. Their antimicrobial activity and effects on the in vitro human cardiac MSC growth, either in the presence or in the absence of oxidative stress, were here assessed. On the basis of the results here presented, these new H2S-releasing PFM could represent promising and low-cost scaffolds or patches for biomedical applications in tissue repair.

Prolonged high-intensity grinding can modify the crystal structure of solid substances and/or induce chemical reaction, which is referred to as mechanochemical reaction. Such reactions can exert positive influences on hydrometallurgical processes, therefore, many researchers have applied mechanochemical reactions for metals dissolution from minerals. The mechanism of mechanochemical reaction has been investigated using solid analyses and simulations. Structural changes caused by mechanochemical reaction are not yet sufficiently clarified because the ground samples are amorphous. The objective of this study was to analyze structural changes of cerianite in weathered residual rare earth ore by mechanochemical reduction. Structural change was analyzed by x-ray absorption near-edge structure and extended x-ray absorption fine structure analysis at the cerium L_III- and K-edges. These analyses revealed that the structural change of cerianite in this ore induced by mechanochemical reduction involved oxygen vacancy production. The process of the oxygen vacancy formation was closely coupled with the quantum effect of localization–delocalization of the 4f electron of cerium.

We have proposed a data-driven approach for designing mesoscale porous structures of Li-ion battery electrode with three-dimensional virtual structures and machine learning techniques. Over 2,000 artificial 3D structures assuming positive electrode composed of random packed spheres as active material particles are generated, and charge/discharge resistance has been evaluated using simplified Physico-chemical model. In this model, resistance from Li diffusion in active material particles (diffusion resistance), transfer resistance of Li+ in electrolyte (electrolyte resistance) and reaction resistance on the interface between active material and electrolyte are simulated based on mass balance of Li, Ohm’s law in and linearized Butler-Volmer equation, respectively. Using these simulation results, regression models via Artificial Neural Network (ANN) have been created in order to predict charge/discharge resistance from porous structure features. In this study, porosity, active material particle size and volume fraction, pressure in the compaction process, electrolyte conductivity, and binder volume fraction are adopted as features, associated with controllable process parameters for manufacturing battery electrode. As results, the predicted electrode resistance by ANN regression model is good agreement with the simulated values. Furthermore, sensitivity analysis and optimization of the process parameters have been carried out. The proposed data-driven approach could be a solution as a guiding principle for manufacturing battery electrode.

The Fourier Continuous Derivative ($D_C$) offers a unique perspective on fractional differentiation grounded in the theory of Fourier series. This approach has the potential to address problems across various disciplines, including physics, engineering, and mathematics. The primary insight underpinning this approach is that a convex function defined on $\mathbb{Z}$ retains its convexity on $\mathbb{R}$. This paper delves into the Fourier Continuous Derivative, compares it with traditional fractional derivatives, and outlines its possible real-world applications, such as modeling viscoelastic materials, solving wave equations, and financial data analysis.

The as-received commercial Inconel 718 material was solid solution heat treated (ST), cold rolled (CR), and precipitation hardened (PH) to investigate the effects of deformation on tensile properties, hardness, and texture. Three sets of specimens (0%, 20% and 50% CR) were STed at 1100 C/1h, CR and aged (720 °C/8 h + 650 °C/8 h) for the analysis. Ultimate tensile strength (UTS), 0.2% yield strength (YS) and elongation of 50% deformed condition were 1645 MPa, 1512 MPa, and 3.8 %, respectively. The 20 % deformation resulted in a balanced UTS (1348 MPa), YS (1202 MPa) and elongation (11%). Contributions of precipitation hardening to the strength was decreasing, while contribution of CR increases with increasing percentage of deformation. Correspondingly, the size and quantities of  decreased with increasing deformation level. In CR specimens, a high density of nano/micro twins were generated with the twin planes oriented perpendicular to the RD-ND surface. The preferred rotation of the crystals generated the gradient of orientation and internal features of the large austenitic grains. The cross-slip of screw dislocations induced a complete β-fibre, consisting of {110}, {112}, and{123}, with doubled intensity at higher deformation. In addition, the specimens tended to be highly susceptible to the twinning-induced orientation emerged by a predominant ⫽ND. An incomplete but intense α-fibre clustered between {110} and {110} was characterized in the as-deformed condition. Besides achieving highest strength, the current work demonstrates the effects of CR on the material strength without the complex influences of  precipitate.

Quercetin is a flavonoid with a low molecular weight that belongs to the human diet's phenolic phytochemicals and non-energy constituents. Quercetin has a potent antioxidant capacity, being able to capture Reactive Oxygen Species (ROS), reactive nitro-gen species (RNS), and Reactive Chlorine Species (ROC), which act as reducing agents by chelating transition metal ions. Its structure has five functional hydroxyl groups, which work as electron donors and are responsible for capturing free radicals. In addition to its antioxidant capacity, it was described different pharmacological properties of Quercetin, such as carcinostatic properties, antiviral, antihypertensive, anti-inflammatory, protection of Low-Density Lipoprotein (LDL) oxidation, and inhibi-tion of angiogenesis are developed in this review.

The emergence of diverse infections worldwide, which is a serious global threat to human existence, necessitate the urgent development of novel therapeutic candidates that can combat these diseases with efficacy. Isatin, a secondary metabolite from tryptophan is considered a privileged scaffold and favorable pharmacophore with a unique structural moiety and varied chemical and biological properties resulting in its widespread applications by medicinal chemists. Molecular hybridization is one of the most common and important techniques use in the synthesis of their bioactive hybrids in drug discovery. This review containing published articles from 2005 to 2022 focuses on isatin hybrids which have been synthesized and reported in the literature alongside a discussion on their biological properties. The purpose of this review is to set up the direction for the design and development of isatin-hybrids with tailored biological properties as effective therapeutic candidates inspired by nature.

Several chronic diseases derive from metabolic, genetic, or inflammatory causes and often these causes are interconnected. Pharmacological treatments, although effective, often lead to unpleasant side effects. In this context, preventive approaches are of growing interest. The literature data of recent years support that the dietary intake of bioactive compounds can positively influence the biological functions of an organism. Among the bioactive compounds in the diet, polyphenols are widely recognized for their beneficial effects on health, as useful compounds for preventing/combating a series of pathologies related to lifestyle, metabolism, and aging. The artichoke (Cynara scolymus L.), a member of the Asteraceae family, is widely used in the food and herbal medicine fields for its beneficial properties. Artichokes are rich in polyphenols (including cynarin), flavonoids and their derivatives, and, for this reason, they have aroused interest in their pharmacological properties. The best-known activity of polyphenols is antioxidant activity. Through it, they help to neutralize free radicals, preventing cellular damage and the subsequent risk of conditions such as cancer, diabetes, and heart disease. Related to the antioxidant action we find the anti-inflammatory activity. This is an important benefit since chronic inflammation is a cause or contributory cause of many chronic diseases. Although many scientific results are of great interest and potential, there are still gaps to be filled. In this review, we report and discuss new insights providing documented evidence regarding the benefits of the artichoke compounds and their possible use to support the pharmacological treatment of pathologies associated with inflammation.

Four decades have elapsed since the first quasiperiodic crystal was discovered in the Al-Mn alloy system, and many progresses have been made during this time interval in the science of quasicrystals (QCs). Notwithstanding this, a significant number of open questions still remain regarding both fundamental and technological aspects. For instance: What are QCs good for? How can we improve the current provisional QC definition? What is the role of the underlying quasiperiodic order and the characteristic inflation symmetry of these compounds in the emergence of their unusual physicochemical properties? or, What is the nature of chemical bonding in QCs formed in such different sorts of materials as alloys, oxides, or organic polymers? In this essay I will discuss these, and other closely related, issues from an interdisciplinary perspective and will comment on appealing prospectives in the field for the years to come.

The hard-shelled seed industry plays an important role in the global agricultural economy. As a result of nut industrialization, considerable amounts of by-products and residues are produced year by year, burnt as fuel or discarded as non-valued waste, by-passing a potential source of valuable compounds or features. Over the last decade nutshells have received great interest due to their lignin concentration and their antioxidant, physical and mechanical features. It was found that these properties vary among cultivars, latitude and localities of plantation. On the other hand, there is inconsistences regarding to mechanical and some biochemical properties of both nutshells, which aimed to explore the status of potential hazelnut and walnut shells appli-cations into sustainable circular bio-economy chains. Hence, this review deals with the recent scientific literature on their chemical composition as well as their functional applications as an approach to sustain the utilization of the main by-product derived from the nut-industry.

Hybrid biomaterials were engineered using the electrospinning technique, incorporating the dipeptide Boc-L-phenylalanyl-L-Isoleucine into microfibers composed of biocompatible polymers. The examination by scanning electron microscopy affirmed the morphology of the microfibers, exhibiting diameters ranging between 0.9 to 1.8 µm. The dipeptide self-assemblies into spheres with a hydrodynamic size between 0.18 to 1.26 µm. The dielectric properties of these microfibers were characterized through impedance spectroscopy, where variations in both temperature and frequency were systematically studied. The investigation revealed a noteworthy rise in the dielectric constant and AC electric conductivity with increasing temperature, attributable to augmented charge mobility within the material. The successful integration of the dipeptide was substantiated through the observation of Maxwell-Wagner interfacial polarization, affirming the uniform dispersion within the microfibers. In-depth insights into electric permittivity and activation energies were garnered using the Havriliak-Negami model and the AC conductivity behavior. Very importantly, these engineered fibers exhibited pronounced pyroelectric and piezoelectric responses, with Boc-Phe-Ile@PLLA microfibers standing out with the highest piezoelectric coefficient, calculated to be 56 pC/N. These discoveries help us understand how dipeptide nanostructures embedded into electrospun nano/microfibers can greatly affect their pyroelectric and piezoelectric properties. They also point out that polymer fibers could be used as highly efficient piezoelectric energy harvesters, with promising applications in portable and wearable devices.

The aim of this study was to investigate the biochemical properties and gel-forming capacity of duck myofibrillar proteins under the effects of 2,2'-azobis (2-amidinopropane) dihydrochloride (AAPH)-mediated oxidation. Duck myofibrillar proteins were extracted and treated with different concentrations of AAPH solutions (0, 1, 3, 5, 10 mmol/L) and then analysed for carbonyl content, dynamic rheology, protein profiles and gel-forming properties (colour, water holding capacity, hardness, protein profile, microstructure). The results showed that with increasing AAPH concentration, the carbonyl content of protein showed an increasing trend (p < 0.05); SDS-PAGE pattern results indicated that moderate oxidation (3 mmol/L AAPH) induced myosin aggregation via covalent bonds including disulfide, enhanced protein-protein, and thus improved protein-water interactions and gel strength of DMPs heat-induced gels. However, high oxidation (5 and 10 mmol/L AAPH) led to partial degradation of myosin heavy chain (MHC), as evidenced by lower storage modulus and irregular microstructure, which significantly reduced gelation ability. These results suggest that the internal relationship between alkanoperoxy radical-induced oxidation should be taken into account in the processing of duck meat, as mild protein oxidation is conducive to improving gel quality.

Although 7055 aluminum alloy is a deformed aluminum alloy and will show excellent mechanical properties after recrystallization after large deformation, it is a method to enrich its application range if rare earth is added and the rare earth phase dispersion is promoted by heat treatment. This article used optical microscopy, scanning electron microscopy energy dispersive spectroscopy (SEM-EDS), X-ray diffraction (XRD), micro Vickers hardness and room temperature stretching methods to study the as-cast 7055-xEr (x=0wt.%, 0.2wt.%, 0.4wt.%, 0.6wt.%, 0.8wt.%) aluminum alloy after being subjected to 460 oC×3h homogenization and 410 oC×1h solid solution+150 oC×12h aging treatment the changes in microstructure and properties. The results indicated that: when 0.2wt.%Er was added to 7055 aluminum alloy after solution at 410 oC×1h and aging at 150 oC×12h, the dendrite structure was significantly reduced, the grain thinning was obvious and the distribution was uniform, Al8Cu4Er phase appeared in the lamellar eutectic η-Mg(Zn,Al,Cu)2 structure at grain boundaries, and the hardness reached 168.8HV. The yield strength, tensile strength and elongation were 542.12Mpa, 577.67MPa and 8.36%, respectively.

Polyethylene terephthalate (PET) is nowadays one of the most used polymers for packaging applications. Modifications induced by service conditions and the optimal mean to recycle this matter several times have to be perfectly understood to allow a reuse for similar application (from bottle to bottle for example). The present study aims to compare physico-chemical properties, crystalline organization, and mechanical behaviour of virgin (vPET) and recycled PET (rPET). Using different combined experimental methods (Calorimetry, Small Angle X-ray Scattering, Atomic Force Microscopy, DMA, and uni-axial tensile test), it has been proven that even if there is no change in the crystallinity of PET, the crystallisation process shows some differences (size and number of spherulites). The potential impact of these differences on local mechanical characterization, at the lamella scale, is explored and tends to demonstrate the development of homogeneous microstructure, leading to well-controlled and relevant local mechanical properties. This approach increases the understanding of crystallisation of PET and recycled PET during forming processes such as thermoforming or injection stretch blow moulding (ISBM) where elongation at break can depend on the microstructure conditioned by the crystallisation process.

Bacterial infections have attracted the attention of researchers in recent decades, especially due to the special problems they have faced, such as their increasing diversity and resistance to antibiotic treatment. The emergence and development of the SARS-CoV-2 infection stimulated even more research, to find new structures with antimicrobial and antiviral properties. Among the heterocyclic compounds with remarkable therapeutic properties, benzimidazoles and triazoles stand out, possessing antimicrobial, antiviral, antitumor, anti-Alzheimer, anti-inflammatory, analgesic, antidiabetic, or anti-ulcer activities. In addition, the literature of the last decade reports benzimidazole-triazole hybrids with improved biological properties compared to the properties of simple mono-heterocyclic compounds. This review aims to provide an update on the synthesis methods of these hybrids, along with their antimicrobial and antiviral activities, as well as the structure–activity relationship reported in literature.

Advanced Nano structural hard coatings are thin materials films that range in thickness from a few nanometers to a few micrometers and are applied to different surfaces to increase their hardness and wear resistance. Physical vapor deposition (PVD) or chemical vapor deposition (CVD) methods are frequently used to deposit these coatings. These coating’s distinctive characteristics result from their microstructure, which is made up of material columns or grains with a diameter of only a few nanometers. Increased hardness, higher wear resistance, and improved tribological properties result from these short dimensions. In applications with significant wear and/or high contact pressures, such as cutting tools, bearings, and engine parts, the usage of sophisticated Nano structural hard coatings is crucial. Advanced Nano structural hard coatings include, 1. Amorphous carbon coatings with high hardness, low friction, and exceptional wear resistance are known as diamond-like carbon (DLC) coatings. DLC coatings are frequently used in a variety of industries, including the automotive, aerospace, and biomedical ones. 2. Coatings made of titanium nitride (TiN): These metallic coatings have high hardness and wear resistance. Cutting tool, machining, and aerospace industries frequently use TiN coatings. 3. Chromium nitride (CrN) coatings: These coatings have great corrosion resistance, good wear resistance, and high hardness. Cutting tools, gears, and bearings are just a few of the objects that use CrN coatings. 4. Tungsten carbide (WC) coatings: These coatings, which have a high degree of hardness and wear resistance, are frequently employed in cutting tools and other applications that require wear resistance. Advanced Nano structural hard coatings provide many advantages over conventional coatings, including better hardness, increased wear resistance, and improved tribological qualities. The automotive, aerospace, and biomedical industries are just a few that could use these coatings. In this paper the author will explain about the design synthesis and applications of advanced Nano structural hard coating in aerospace and automotive applications.

Two-dimensional (2D) materials have been a research hot topic in the passed decades due to their unique and fascinating properties. Among them, mechanical properties plays an important role for their application. However, there lacks an effective tool for high-throughput calculating, analysing and visualizing the mechanical properties of 2D materials. In this work, we present, mech2d package, a highly automated toolkit for calculating and analysing second-order elastic constants (SOECs) tensor and relevant properties of 2D materials with considering their symmetry. In the mech2d, the SOECs can be fitted by both strain-energy and stress-strain approach, where the energy or strain can be calculated by first-principles engine, such as VASP. As a key feature, the mech2d package can automatically submit and collect the tasks from local or remote machine with robust fault-tolerant ability, make it suitable for high-throughput calculation. The present code has been validated by several common 2D materials, including graphene, black phosphorene, GeSe2 and so on.

In this study, cement is used as the component that provides the stabilizing effect in order to evaluate the hardness and stability of loess soil. To assess the strength characteristics of loess soil reinforced with cement, samples were created with four different cement contents and three different curing times. The materials were put through a series of tests to determine their flexural strength, direct shear strength, indirect tensile strength, and unconfined compressive strength. An appropriate cement dosage was found, in addition to a durability index that could be used to quantify the effect of water absorption investigations on cement-stabilized loess. Both of these discoveries were made simultaneously. Analyses of investigations such as scanning electron microscopy (SEM) and energy dispersive X-ray fluorescence spectrometry (XRF) examinations were carried out so that the fundamental mechanics of the materials could be comprehended. According to the findings, the cohesion of cement-stabilized loess is significantly more sensitive to structure than the friction angle of the material, and the cohesion is responsible for the increase in shear strength after remolding. To get the desired level of strength, it is necessary to adjust the cement's proportions. In addition, as the curing period progresses, we see an increase in the cement-stabilized loess's resistance and stiffness. This is because of the interactions that take place between the structure and the mineral composition. It is believed that this event was caused by the cementation that occurs naturally. As a consequence of this reaction, the production of new cementitious materials takes place. The cation exchange that causes the hydration and pozzolanic reaction that leads to the creation of aggregates and interparticle flocculation is responsible for their production. These findings suggest that cement may be utilized as a simple and effective method of loess stabilization, which will ultimately result in improved performance of the loess.

Due to the accumulation of pesticides in the environment, the development of efficient strategies for their removal is of utmost importance. Activated carbons are currently seen as excellent candidates for adsorptive pesticide removal based on several beneficial properties, like a large surface area, developed porosity, and low price. However, a deep link between materials' properties and performance is still elusive. Here we focus on the kinetics of three organophosphate pesticides removal, aliphatic dimethoate and malathion and aromatic chlorpyrifos, using a series of carefully prepared activated carbon fibers. Used adsorbents have a wide range of specific surface areas, pore size distributions, and elemental content, allowing the establishment of the link between physicochemical properties and their performance as adsorbents. We use data analysis tools to link these properties and discuss their different roles in the removal of three structurally different yet extremely dangerous pesticides. The obtained results can guide the synthesis of novel adsorbents or rationally select adsorbents for specific target pollutants based on the physicochemical properties of adsorbents and the chemical structure of pollutants.

In contrast to the traditional fillers, clay, in particular, natural smectite clay represents an environmentally significant alternative to improve the properties of polymers. Compared to con-ventional nanofillers, smectite clay can effectively enhance the physical and mechanical properties of polymer nanocomposites with a relatively small amount of addition (< 5 wt%). The present study focuses on investigating the reinforcing efficiency of different amounts (up to 5 wt%) of a natural Brazilian smectite clay on the mechanical and thermal properties of poly(butylene terephthalate) (PBT) nanocomposites. Natural Brazilian clay modified by addition of quaternary salt and sodium carbonate (MBClay) was infused into the PBT polymer by melt extrusion, using a twin-screw extruder. It was found that the best properties for PBT were obtained at 3.7 wt% of modified BClay. Tensile strength at break exhibited an increase of about 60 %, flexural strength increased by 24 % and flexural modulus increased by 17 %. In addition, an increase in the crystallinity percentage of PBT/BClay nanocomposite was confirmed by DSC and XRD analysis, and a gain of about 45 % in HDT was successfully achieved due to incorporation of 3.7 wt% of MBClay.

Good estimators are characterized as robust, unbiased, efficient, and consistent. However, the commonly used estimators are weak or lack one or more of these properties. In this article, eight (8) estimators for statistical and geometrical estimations of symmetry/asymmetry, similarity/dissimilarity, identity/unidentity, and feature transformation were proposed following Kabirian-based optinalysis and other operations. The proposed estimators are characterized as invariant (robust) under scaling, location shift, and rotation or reflection. A computing code was written in python language for each of the proposed estimators so that peers can have working codes for application and performance evaluation.

Alternating TiB2-dcMS and Cr-HiPIMS layers are used to fabricate TiB2/Cr multilayer films. In-troducing a 5-nm-thick Cr interlayer deposited under a substrate bias of -60 V produces slight increases of both film hardness and elastic modulus. The TEM observation indicates that the Cr grains favor epitaxially growth on TiB2 interlayer, forming a coherent TiB2/Cr interface. This produces the hardness increasement. Mechanic measurement by using AFM illustrates that the coherent interface increases the elastic modulus of the Cr up to ~280 GPa, which is significantly higher than bulk material.

With the increase in occupation-specific risks of lip cancer associated with solar radiation, there is a need for developing photoprotective lipsticks to protect skin against harmful effects of UV radiation. Considering the unique chemical and physical properties of low-molecular-weight organogelators (LMOGs), the present study intended to assess the UV protective properties of LMOGs-based lipstick formulations. In this study, dibenzylidene-D-sorbitol (DBS) and 12-hydroxystearic acid (12-HSA) were used to formulate lipsticks : L1 (1% DBS), L2 (10% 12-HSA), L3 (1.5% DBS) and L4 (control, no LMOGs). The lipstick formulations were tested for in vitro sun protection factors (SPF), UVA protection factor (UVA-PF), thermal, mechanical and texture analyses. Lipsticks with LMOGs exhibited higher UVA-PF and SPF, and more particularly 12-HSA-based lipstick. Results showed also the viscoelastic and heat-resistant properties of LMOGs and their effect of increasing pay-off values. In general, texture analysis indicating that 12-HSA-based lipstick was significantly harder to bend compared to control, while other formulations became softer and easier to bend throughout the stability study. Finally, sensorial and instrumental analyses permitted to classify lipsticks into two groups. This work suggests the potential use of LMOGs as a structuring agent for lipsticks paving the way towards more photoprotective and sustainable-derived alternatives.

Quantity-intensity characteristics are among conventional approaches for studying potassium dynamics and its availability; this was assessed to determine availability in four districts: namely, Sodo Zuria, Damot Gale, Damot Sore, and Boloso Sore at three different land use type viz., enset-coffee, crop land, and grazing land. There was water soluble, ammonium acetate, nitric acid extractable potassium, exchangeable potassium, and non-exchangeable potassium studied in soil samples, which were collected from 0-20 cm depth of each land type. The study revealed that water soluble and ammonium acetate extractable potassium concentrations ranged from 0.04 to 0.42 cmolKg-1 soils enset-coffee and grazing land use types, respectively. The study showed that exchangeable potassium constituted the highest proportion of available potassium, while the proportion of water soluble potassium was found to be the lowest. In this study, non-exchangeable potassium concentrations varied from 0.10 to 0.04cmolKg-1soils for enset-coffee, and crop and grazing land use type. Furthermore, available potassium and exchangeable potassium concentrations were positively correlated with OC(r=0.95***), cation exchange capacity, and sand and clay(r=0.98***). In addition, the K dynamics as impacted by land use types found that the highest change in exchangeable potassium (0.31cmolkg-1soils) and potential buffering capacity (1.79cmolkg-1soils) were noted in crop land use types, whereas the lowest change(1.26cmolkg-1 soils) was observed in the enset-coffee system, The varying properties, potassium status, dynamic and land use type of soils identified in the study areas provided adequate information to design soil potassium management options and further research about the soil in each site. Therefore, application of site specific soil fertility management practices and research can improve soil potassium status and quantity intensity parameters to sustain crop productive soils.

The present study investigated the effects of alloying and nano-reinforcement on the mechanical properties (microhardness, tensile strength, and compressive strength) of Mg-based alloys and composites. Pure Mg, Mg-3Sn alloy, and Mg-3Sn+0.2GNP alloy-nanocomposite were synthesized by powder metallurgy followed by hot extrusion. The microstructural characteristics of the bulk extruded samples were explored using X-ray diffraction, field-emission scanning electron microscopy, and optical microscopy and their mechanical properties were compared. The microhardness, tensile strength, and compressive strength of the Mg-3Sn alloy improved when compared to those of monolithic Mg sample and further improvements were displayed by Mg-3Sn+0.2GNP alloy-nanocomposite. No significant change in the compressive strain to failure was observed in both the alloy and the alloy-nanocomposite with respect to that of the pure Mg sample. However, an enhanced tensile strain to failure was displayed by both the alloy and the alloy-nanocomposite.

The paper presents an analysis of the possibility of producing traction brushes from waste materials. Brushes are used to ensure good electrical contact between the rail and the pantograph. Slides are produced in the process of hot pressing, with parameters of heating up to max 175 ⁰C, at the minimal pressure value of 200 MPa. The developed brushes with a high (55-60%) content of recycled materials have comparable characteristics to commercial brushes, and some of the prototypes are even more durable and break-resistant.

There is an increasing interest in applying environmentally-friendly materials in wood protection technology. This include the use of less toxic active ingredients, as well as better fixation. This study investigates the formulation based on the combination of copper and Saqez resin on the physical and biological resistance properties of poplar wood. Samples were treated by either copper-ethanolamine (Cu/MEA) and/or Saqez resin at various treatment levels. A vacuum pressure procedure was applied. The retention, weight percent gain, water absorption, volumetric swelling, and decay resistance of the samples were then determined. The highest retention and weight percent gain were obtained at the samples treated with the combination of copper-based system and Saqez resin. Additionally, the combination of the copper and Saqez improved the physical properties and decay-resistance against white-rot fungus Trametes versicolor.

The research hypothesis states that the impregnation of the honeycomb paper core of lightweight sandwich panels with modified starch, sodium silicate and LiquidWood® resin has a significant effect on the elastic properties of it. In the study, a recycled paper was used in three thicknesses, seven types of cell shapes, including two after numerical optimization and three types of impregnating agents. The method of digital image analysis determined the elastic constants of manufactured paper cores, which were subjected to axial compression in two directions. Based on the experimental results, elastic constants of the cores were calculated and compared with the results of numerical calculations. It has been shown that each of the impregnating solutions used improves the stiffness of the paper core. The best results were obtained for LiquidWood® epoxy resin and modified starch. An important parameter of cell geometry affecting their rigidity is the angle of the cell wall φ, as well as the arrangement of the common cell wall in relation to the direction of load. The numerical models developed were positively verified.