In metal continuous casting process is important to estimate the temperature evolution of casted section along machine from meniscus (point in which liquid metal is poured) to cutting machine where product is cut at commercial length. Particularly in the case of large sections, a convenient approximated model to achieve this goal with a feasible computational effort, is the so called travelling slice: the transversal section of casted product is subjected to different thermal boundary conditions (e.g. thermal flux, radiation, convection) that are found during the movement at constant speed from meniscus to the end of machine. In the case of an axisymmetric section, a comparison with the exact solution can be easily achieved. The article will show pros and cons of both, namely the far lower computational cost of travelling slice model without losing precision. Results confirm the validity of the travelling slice approach also at low casting speed and huge dimensions.

We present functionalization of AISI 316L surfaces by nanosecond Nd:YAG laser texturing in order to modify the surface morphology with crosshatch and dimple patterns. We performed tribological analysis under lubrication with sunflower and jojoba oil with and without addition of solid lubricant, MoS2 nanotubes. In connection to friction/wear response we analysed laser-textured surface wettability, oil spreadability and oil retention capacity. We have shown, that the crosshatch pattern generally exhibited lower friction than the dimples pattern, with the addition of MoS2 nanotubes not having any significant effect on the coefficient of friction under the investigated contact conditions. This was additionally with better oil spreadability and oil retention capacity results of crosshatch textured surface. Furthermore, texturing reduced wear of the stainless steel surfaces but led to approximately one order of magnitude larger wear rate of the steel counter-body, primarily due to the presence of hard bulges around the textured patterns. Overall, the crosshatch pattern showed better oil retention capacity and lower friction in combination with different vegetable oils, thus making it a promising choice for improving tribological performance in various environmentally friendly applications.

To weaken the harm of Al-Si coating and increase the strength of welded joint, variable thickness of Ni foil (Ni, an austenitic formation element) was added into the lap laser welding Al-Si coated 22MnB5 hot stamping steel/galvanized steel joints. The joints' weld appearance, microstructure, and mechanical properties were explored. The weld altered from X-shape to Y-shape with the increased thickness of Ni foil. During welding, Al-Si coating was melted and diluted into the welding pool, forming δ-ferrite (a rich-Al phase with low toughness and strength) in FZ and FB. This phase deteriorated the strength of the joints. After adding Ni, the amount and size of the δ-ferrite phase decreased. With a significant thickness of Ni foil, δ-ferrite would disappear. However, a new phase (FM, rich-Ni phase) probably formed except PM(a no or negligible Ni phase). The heat-affected zone (HAZ) on the side of 22MnB5 comprised a coarse martensite zone, refined martensite zone, martensite+ferrite zone, and tempered martensite zone from the FZ to the basic material. HAZ on the side of galvanized steel mainly contained ferrite and pearlite. After adding Ni foil, the strength of the joint was more than that without Ni. The maximum strength of the joint can be up to 679MPa because of the disappearance of δ-ferrite. Meanwhile, the toughness of the joint increased. The fracture mode was from three mixed fractures(cleavage, quasi-cleavage, and dimple) to one fracture(dimple).

In view of the limitations of the existing optimization method of suspender cable force, in order to improve the stress of suspender under completion state and avoid frequent adjustment of cable force and grid beam elevation during construction, a new method of cable force optimization is proposed. The article takes the longest large span arch bridge in the world, Pingnan Third Bridge, a Concrete-filled steel tube (CFST) arch bridge with a span of 575m as the engineering background combined with the finite element analysis and multi-objective optimization method. One cable force optimization method that suspender “Real-time correction during construction, in the process variable optimal and results reliable” during panel girder lifting of long span CFST arch bridges is clarified. Taking the panel girder weight and displacement during the construction as parameter variables, the displacement and unevenness of the panel girder under completion state as constraint conditions, the displacement and cable force during the hoisting construction as the objective equation, through the optimization of the objective equation, the suspender cable force and dis-placement of each hoisting section are calculated. The results show that it is feasible to introduce the optimization theory into the cable force optimization when lifting the panel girder. the segment displacement variation is minimized to meet the destination. The cable force distributed evenly under completion state of the bridge that further making sure the completion state satisfies the requirements. No repeating iteration is needed, thus avoiding cumberso me calculation, getting cable force once. With higher optimization efficiency and better effects, the method provides high value for the cable force calculation of same type bridge suspender construction and for guiding construction.

This paper offers a set of comprehensive guidelines aimed at facilitating the widespread adoption of hydrogen in the industrial hard-to-abate sectors. The authors begin by conducting a detailed analysis of these sectors, providing an overview of their unique characteristics and challenges. The paper delves into specific elements related to hydrogen technologies, shedding light on their potential applications and discussing feasible implementation strategies. By exploring the strengths and limitations of each technology, the paper offers valuable insights into its suitability for specific applications. Finally, through a particular analysis focused on the steel sector, the authors provide in-depth information on the potential benefits and challenges associated with hydrogen adoption in this particular context. By emphasizing the steel sector as a focal point, the authors contribute to a more nuanced understanding of hydrogen's role in decarbonizing industrial processes and inspire further exploration of its applications in other challenging sectors.

This study investigated the mechanical properties and fatigue behavior of FH36 steel plate rolled in different directions. By adopting a sequential rolling process in the rolling direction (RD) and transverse direction (TD), the differences in properties between RD and TD were eliminated, resulting in nearly identical tensile properties. The steel plate exhibited a yield strength of approximately 420 MPa, a tensile strength of approximately 506 MPa, and an elongation of approximately 25%. Fatigue tests conducted at room temperature and -60℃ showed a fatigue limit of the maximum stress of 488 MPa at room temperature and 500 MPa at -60℃, indicating improved low-temperature fatigue performance. The fracture surfaces displayed distinct characteristics, such as oblique shearing fractures for high-cycle fatigue and cup-cone shape fractures for low-cycle fatigue. The fatigue source zone were both on the surface of the specimens. As the maximum stress increased, the area of the crack propagation zone for high-cycle fatigue decreased, while the area of the final fracture zone, the number of dimples and the proportion of the LAGBs increased.

The welding and construction processes of H-type thick-plate-bridge steel involve complex multi-pass welding processes, which is difficulty to ensure its welding performance. Accordingly, it is crucial to explore the inherent correlation among the welding processes parameters and welding quality, and applied it into the welding robots, eliminating the instability from manual welding. In order to improve the welding quality, the GMAW (Gas Metal Arc Welding) welding process parameters are simulated using the Q345qD bridge steel flat joint model. Four welds with X-shaped grooves are designed to optimize the parameters of welding current, welding voltage, and welding speed. The optimal welding process parameters are investigated through thermal-elastic-plastic simulation analysis and experimental verification. The results indicate that when the welding current is set to 230A, the welding voltage to 32V, and the welding speed to 0.003m/s, the maximum deformation of the welded plate is 0.52mm, with a maximum welding residual stress of 345MPa. Both the simulation results of multi-pass welding and experimental tests meet the welding requirements, as they show no excessive stress or strain. These parameters can be applied into building large steel frame bridges with welding robots, improving the quality of welded joints.

Currently, the design of the concrete mix is an important part of the environmental problem. In front of this question, engineers face a major challenge that is addressed in two ways. On one hand, how do they use its component materials to improve its mechanical properties, on the other hand how do they use less polluting materials? Hence, in an environmental and economical view, laboratory tests were carried out on samples of concrete reinforced with smooth steel fiber extracted from the waste tires, in order to assess its impact and to prove its mechanical feasibility for these purposes. Consequently, laboratory results have shown satisfactory improvement in the behavior of concrete under compression loads in the elastic stage and an increase in ductility and toughness of the matrix in the plastic stage. Besides, taking into account the discontinuity and the structural disturbances observed during the loading of samples in the post-elastic state, a method has been proposed to calculate "the effective toughness and toughness Index of fiber concrete; on the other hand, this method has helped to better optimize length and slenderness of fibers for better use of this recycled material

Limited availability of expensive alloying elements elevates low-alloyed steels to a unique position in the field of lightweight construction and mass production. Quenching and partitioning (Q&P) heat treatments of low-alloyed steels with exceptional property combinations are particularly promising. In this study, we characterize for the first time a new low-alloyed steel to be processed by Q&P heat treatments. In combined experimental and numerical studies, we design a novel approach that effectively combines the short cycle times of press hardening with the excellent property profiles of Q&P-treated steels. We identify appropriate transformation parameters for Q&P heat treatments by dilatometric studies and we adjust a number of reference conditions with different isothermal holding times. By means of SEM analysis and XRD measurements, we show that different fractions of retained austenite result in different mechanical properties. Initial numerical designs of the process can identify varying temperature profiles and cooling rates depending on the position in the die. The results show that the geometry of the part plays a minor role, but the die temperature is the dominant factor for successful partitioning directly in the press hardening process.

Current conventional methods of evaluating microstructures are characterized by a high degree of subjectivity and a lack of reproducibility. Modern machine learning (ML) approaches have already shown great potential in overcoming these challenges. Once trained with representative data in combination with an objective ground truth, the ML model is able to perform a task properly in a reproducible and automated manner. However, in highly complex use cases, it is often not possible to create a definite ground truth. This study addresses this problem using the underlying showcase of microstructures of highly complex quenched and quenched and tempered (Q/QT) steels. A patch-wise classification approach combined with a sliding window technique provides a solution for segmenting entire microphotographs where pixel-wise segmentation is not applicable due to the problem of reproducibly creating unambiguous training masks. Using correlative microscopy, consisting of light optical microscope (LOM) and scanning electron microscope (SEM) micrographs as well as corresponding data from electron backscatter diffraction (EBSD), a training dataset of reference states that covers a wide range of microstructures was acquired in order to train accurate and robust ML models. Despite the enormous complexity associated with the steels treated here, classification accuracies of 88.8% in the case of LOM images and 93.7% for high-resolution SEM images were achieved. These high accuracies are close to super-human performance, especially in consideration of the reproducibility of the automated ML approaches compared to conventional methods based on subjective evaluations through experts.

The possibility of increasing the resource of steel fingers working in tandem with bronze bushings by plasma-electrolytic nitrocarburizing of the surface of medium carbon steel is shown. The phase composition, microhardness, morphology and surface roughness were studied. Tribological tests were carried out under dry friction conditions according to the shaft-pad scheme. It has been established that plasma-electrolytic nitrocarburizing of the surface of medium carbon steel at a temperature of 700 °C for 5 minutes leads to a decrease in a friction coefficient by 2.3 times, weight wear of steel by 24.9 times, and bronze counterbody by 5.9 times. At the same time, the contact stiffness increases 2.6 times. The type of wear is fatigue with dry friction and plastic contact. Changes in tribological characteristics are associated with the high hardness of the hardened steel surface together with the influence of dispersed nitrides and iron carbonitrides distributed in it.

The materials used as corrosion inhibitors are [Zn-Al-Cl], [Mg-Al-Cl], [Ni-Fe-Cl], and [Co-Fe-Cl] layered double hydroxides (LDHs). They were synthesized by coprecipitation and characterized by X-ray diffraction (XRD), Fourier transforms infrared spectroscopy (FTIR), and thermal anal-yses. The efficiency of these corrosion inhibitors on mild steel in concentrated hydrochloric acid (18.5%) at 60°C (chemical pickling conditions of steel) was studied using electrochemical and gravimetric methods for different concentrations. The surface morphology and composition were examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The inhibitory efficiency in the case of 1.2 g.L-1 LDH was found to be 83.33%, 83.65%, 68.38%, and 74.73% for [Ni- Fe-Cl], [Zn-Al-Cl], [Co-Fe-Cl], and [Mg-Al-Cl], respectively.

The effects of partial replacement of Si by Al on the microstructure, tensile properties, and Charpy impact toughness were investigated using 0.2%C-Si/Al-Mn-Cr-B TRIP-aided martensitic steels. The impact toughness was related to the microstructural and mechanical properties. The partial re-placement decreased the volume fraction of retained austenite and increased the mechanical stabil-ity, accompanied by softening and an increase in the volume fraction of the primary martensite. Resultantly, the partial replacement decreased strength and ductility. The impact absorbed energy (value) at 25 C was slightly increased by the partial replacement. The increased impact absorbed energy was mainly caused by high crack/void propagation energy due to the softened primary martensite and a small contribution of the stabilized retained austenite. The 50% shear fracture ductile-to-brittle transition temperature was marginally raised by the partial replacement. The raised transition temperature was mainly associated with an increase in a unit crack path of qua-si-cleavage/cleavage fracture.

The response of structures under pulse-like ground motions is characterized by the large amount of energy input in a few cycles. Consequently, structures with insufficient strength may suffer severe damage owing to excessive deformation. In a previous paper, the energy-based prediction procedure for the peak and cumulative response of a reinforced concrete (RC) frame building with steel damper columns was proposed (Fujii and Shioda, 2023). Although this procedure was verified by comparison to the nonlinear time-history analysis (NTHA) results, the performance of the proposed procedure with pulse-like ground motion records has not been verified yet. In this study, the accuracy of the energy-based prediction procedure for an RC frame building with steel damper columns was investigated by considering pulse-like ground motions. The numerical analysis results reveal that the accuracy of the predicted peak response is satisfactory, which agrees with the results of the author’s previous study. However, the accuracy of the predicted total input energy to the building model depends on the ratio of the pulse period of the ground motion to the effective fundamental period of the building model. The reasons for this underestimation of the total input energy are discussed in this paper.

The microstructure and hardness along the thickness direction of a water quenched, high-strength thick plate with a thickness of 40 mm were investigated with three specimens from the thick plate: surface, 1/4t, and 1/2t (center) thickness, and the phase transformation behavior of the thick plate according to the cooling rate was analyzed through dilatometric experiments. Finally, the cooling rate for each thickness of the thick plate was estimated by comparing the microstructure and hardness of the thick plate along the thickness with those of the dilatometric specimens. Martensite microstructure was observed on the surface of the water quenched thick plate due to the fast cooling rate. On the other hand, an inhomogeneous microstructure was transformed inside the thick plate due to the relatively slow cooling rate and central segregation of Mn. A small fraction of bainite was shown at 1/4t thickness. A banded microstructure with martensite and bainite resulting from Mn segregation was developed at 1/2t; that is, the full martensite microstructure was transformed in the Mn-enriched area even at a slow cooling rate due to high hardenability, but a bainite microstructure was formed in the Mn-depleted area owing to relatively low hardenability. A portion of martensite with fine cementite at the surface and 1/4t was identified as auto-tempered martensite with a Bagaryatskii orientation relationship between the ferrite matrix and cementite. The microstructure and hardness as well as dilatation were investigated at various cooling rates through a dilatometric experiment, and a continuous cooling transformation (CCT) diagram was finally presented for the thick plate. Comparing the microstructure and hardness at the surface, 1/4t, and 1/2t of the thick plate with those of dilatometric specimens cooled at various cooling rates, it was estimated that the surface of the thick plate was cooled at more than 20 oC/s, whereas the 1/4t region was cooled at approximately 5 ~ 10 oC/s during water quenching.

Damage assessment is one of the most crucial issues for bridge engineers, especially for existing steel bridges. Among several methodologies, the vibration measurement test is a typical approach in which the natural frequency variation of the structure is monitored to detect the existence of damage. However, locating and quantifying the damage is still a big challenge. In this regard, the artificial intelligence (AI)-based approach seems a potential way to accomplish those obstacles. This study deploys a comprehensive campaign to determine all dynamic parameters of a pre-damage steel truss bridge structure. Based on the results of mode shape, natural frequency, and damping ratio, a finite element model (FEM) is created and keeps updating. The artificial intelligence network's input data will be analyzed and evaluation from damage cases. The trained artificial neural network model will be curated and evaluated to confirm the approach's feasibility. During the actual operational stage of the steel truss bridge, this damage assessment system is showing good performance in terms of monitoring the structural behavior of the bridge under some unexpected accidents.

Nitriding has long been used to engineer the surfaces of engineering steels to improve their surface and subsurface properties. The role of the surface compound layer (’-Fe4N and/or -Fe2-3N) in improving the tribological and corrosion resistant properties of nitrided steels has been established. However, there have been very few studies on the response of the compound layer to tribocorrosion in corrosive environments. In this work, the tribocorrosion behaviour of a 5 m thick ’-Fe4N nitride layer produced on mild steel (MS) by plasma nitriding has been studied in a NaCl containing solution under various electrochemical conditions. The results show that at a cathodic potential, where mechanical wear is predominant, the total material removal (TMR) from the ’-Fe4N layer is 37% smaller than that from the untreated MS, and at open circuit potential, TMR from the layer is 35% smaller than that from the untreated MS, while at an anodic potential, the ’-Fe4N layer can reduce TMR from mild steel by 87%. The beneficial effect of the ’-Fe4N nitride layer in improving the tribocorrosion behaviour of mild steel is derived from its high hardness and good corrosion resistance in the test solution and its ability to resist both mechanical wear and chemical wear.

This paper proposed a time two-mesh (TT-M) finite difference numerical scheme to improve the efficiency of solving the symmetric regularized long wave (SRLW) equation. The TT-M Crank-Nicolson discretization and finite difference method are employed in time and space approximation respectively. The scheme involves three main steps: firstly, the time interval is divided into coarse and fine time meshes, then the nonlinear system is solved on the coarse time mesh; secondly, coarse numerical solutions on the fine time mesh are computed using an interpolation formula based on the solutions derived in the step one; lastly, the TT-M finite difference numerical solutions can be obtained through constructing the linearized fine time mesh system using Taylor’s formula. Compared to the currently existing TT-M numerical methods, the novelty of this study is that the nonlinear term including derivatives is linearized by Taylor’s formula for a function with three variables, whose error analysis is more complex. Finally, some numerical examples, including computational time and accuracy, preservation of conservation laws, are given to verify the efficiency of the scheme. By comparing it with the standard nonlinear finite difference scheme, this method can reduce CPU time without sacrificing accuracy.

Improper lifting measures of long-span spatial steel structures during construction process may delay the construction period and even cause safety accidents. Few studies on long-span spatial steel structures considered time-varying mechanical characteristic during construction process. In order to achieve safe and efficient installation in a long-span spatial steel structure, this research presents a time-varying mechanical analysis of the synchronous and asynchronous integral lifting and a single and interlaced point’s asynchronous integral lifting analysis method of a long-span spatial steel structure. The results showed that in the case of asynchronous lifting of single point, the displacement influence on other members is related to the distance. The closer the distance from the lifting point, the greater the influence. In asynchronous integral lifting, the lifting point with large lifting force is first installed to the specified position, and the lifting point with small lifting force is installed to the specified position.

In this paper, through high-temperature tensile tests of 55NiCrMoV7 steel, the high-temperature fracture behavior, microstructure evolution and carbide distribution characteristics of both thermal-mechanical coupling zone (fracture zone) and thermal stress zone (clamping zone) at different temperatures were studied. Intrinsic relationship between high temperature fracture and carbides types, distribution and size were revealed and evolution mechanism of microstructure near cracks in 55NiCrMoV7 hot-working die steel during high temperature deformation was clarified. Samples were stretched at different temperatures from 25 °C to 700 °C, and microscopic examinations were carried out by using SEM and TEM. The results showed that: With the increase of temperature, tensile strength and yield strength decreased, elongation and reduction of area increased, and fracture mode changed from brittle fracture to ductile fracture by transition temperature at about 400℃. During high temperature deformation, the grain dislocation density decreased, the tempered martensite decomposed, recovered, recrystallized, and then grain grew. M7C3 and M23C6 carbides precipitated and grew along the grain boundary, and a small amount of fine granular MC carbides were dispersed in the grain. The work done by the external force on the deformation zone would cause the temperature of it to be higher than tensile temperature, which provides thermodynamic conditions for the re-dissolution of small carbides near the fracture zone and the grain growth of large carbides, resulting in the decrease of small carbides and increase of large carbides in thermal-mechanical coupling zone.

A reliable finite element procedure to simulate shear-dominated ductile fracture in large-scale, thin-walled steel structures is still evolving due primarily to the challenges in determining the fracture criterion of steel materials under complex stress states. This paper aims to examine the accuracy of the modified Gurson-Tvergaard-Needleman (GTN) model considering the shear failure in simulating ductile fracture of steel plate structures under quasi-static punch loading. The modified GTN damage models are performed by ABAQUS user defined material subroutine (VUMAT). The void related parameters and shear damage parameters of Xue’s and N-H modified GTN models are calibrated from test specimens with various geometries corresponding to different stress triaxiality and shearing conditions. The damage evolution associated with the shearing of voids in the modified GTN models has strong influences on the stress triaxiality versus equivalent plastic strain under complex stress states, especially for the shear dominated loading conditions. Based on the original GTN model, Xue’s model, and N-H modified GTN model with calibrated material parameters, a numerical comparative study examines the ductile fracture of steel non-stiffened plate and stiffened plate under punch loading. Benchmarked against the experimental studies, the numerical simulations demonstrate that the shear driven void evolution in the modified GTN model imposes significant effects on the load-displacement responses, as well as the onset and extension of ductile fracture in steel plates under punch actions. The N-H modified model with calibrated shear damage parameters shows a better correlation with the ductile fractures in steel plates observed in the experiment, than the original GTN model and Xue’s modified GTN model. As a result of this study, the modified GTN model considering the shear failure can be applied for practical applications in the crashworthiness assessment of ship collision and grounding.

Objective:Over the last two decades one of the main surgical treatment for stress urinary incontinence (SUI) and pelvic organ prolapse (POP) surgery was the insertion of non-absorbable mesh to restore continence and prolapse respectively. Over time complications arose including mesh-associated pain syndrome (MAPS), mesh exposure, mesh-erosion, chronic bladder/vaginal infections, and dyspareunia. Consequently, women chose surgical mesh removal to counter these problems. However, little is known about the demographics, medical co-morbidities, mesh types involved and the timing from mesh insertion to mesh removal. This retrospective study will look at which of these factors may be closely associated with mesh removal surgery.Design:Retrospective studySetting:Female Pelvic Medicine and Reconstructive Surgery (FPMRS) Clinic at University College London Hospitals NHS Foundation Trust.Population:All patients presenting to the FPMRS Clinic between June 2011 to December 2019, requesting mesh removal surgery with a history of MAPS and other mesh complications were included in this study. Methods:Patient demographics including age, ethnicity, obstetric history, and medical co-morbidities; type of mesh/anatomical route used; onset of symptoms; and time from insertion to removal were recorded. Main Outcome Measures:Determination of correlation coefficients between patient demographics, patient reported symptoms and mesh removal surgery. Results:Three hundred and forty-five women with a history of MAPS were included in the study. Women in the 40-60 year old cohort accounted for 54.4% of mesh removal surgery; 54.8% had a BMI under 30 and almost 90% were Caucasian. 96.5% had had children, with over 77% having had a vaginal delivery. 91.9% of patients reported other health conditions including 18.8% with a concomitant history of mental health problems and 15.4% with a history of heart disease. Over 80% of women undergoing mesh removal surgery had a continence mesh (49% retropubic and 32% obturator continence mesh) removed, whereas 20% had an abdominal prolapse and/or vaginal prolapse mesh removed. The average time from mesh insertion to mesh removal was seven years, with the prevalence of mesh removal surgery averaging 85% (range 50 - 100%) depending on the comorbidity determined. Conclusions:All women presented to the clinic with a history of MAPS and other comorbidities which may have influenced their decision to pursue mesh removal surgery. There were no specific predictors, other than chronic pain associated with mesh, determining which women underwent surgery, though those with continence mesh were more likely to do so.

Elastic properties of materials and their changes with temperature are important for their applications in engineering. A study on the influence of phase composition of AISI 4130 alloy on Young's modulus (Ed), shear modulus (Gd), and damping (Q-1) was carried out by Impulse Excitation Technique (IET). The material characterization was carried out using confocal microscopy, XRD, MET, HV, and dilatometry. A stable structure, composed of ferrite (BCC) and pearlite (α-Fe+Fe3C), was obtained by annealing. Metastable structure of martensite (BCT) was obtained by quenching. The Ed, Gd, and Q-1 were measured, varying the temperature from RT to 900 °C. The values of Ed and Gd, at RT, were determined as 201.5 and 79.2 GPa (annealed), and 190.13 and 76.5 GPa (quenched), respectively. In the annealed steel, the values Ed and Gd decrease linearly on heating up to 650 °C, with the thermal expansion. In the quenched steel, weak changes in the dilatometric curve, Ed, Gd, and Q-1, in the range of 350-450 °C, indicated decompositions of the martensitic phase. Sharp decrease in the moduli and high peak of Q-1, was observed for both samples around 650-900 °C, revealing low lattice elastic stability of the phases during transformations α(BCC)+Fe3C↔γ(FCC).

In this paper, a new method by combining cold drawing and martensitic transformation was proposed to produce ultrahigh-strength steel wire, and the effect of austenitizing heating rate on microstructure and mechanical properties was studied. Compared with Muffle furnace heating, salt bath heating has a much higher austenitizing heating rate, which is beneficial to obtain ultrafine-grained martensite for steel wire with a larger section. By salt bath hardening and low-temperature tempering, an ultrahigh strong (strength of 2.48 GPa) and tough (elongation of 6.0%) steel wire was produced. Moreover, to explore whether is it possible to replace long-time low-temperature tempering with short-time tempering at elevated temperatures to improve the tempering efficiency, the effect of tempering time on the evolution of microstructure and mechanical properties of the steel wires tempered at 350 °C was systematically studied. The results demonstrate that tempering at 350 °C for 30 s can endow the steel wire with comparable mechanical properties to that of the one tempered at 250 °C for 2 h. With tempering time prolonging, the strength decreases gradually with the precipitated phase transition from χ-Fe5C2 carbide into θ-Fe3C carbide and coarsening, which plays a major role in the strength decrease.

To achieve the required mechanical properties in the heat treatment of steel, it is necessary to have an adequate cooling rate and to achieve the desired final temperature of the product. This should be achieved with one cooling unit for different product sizes. In order to provide high variability of the cooling system, different types of nozzles are used in modern cooling systems. Designers often use simplified, inaccurate correlations to predict the heat transfer coefficient, resulting in oversizing of the designed cooling or failure to provide the required cooling regime. This typically results in longer commissioning times and higher manufacturing costs of the new cooling system. Accurate information about the required cooling regime and the heat transfer coefficient of the designed cooling is critical. This paper presents a design approach based on laboratory measurements. Firstly, the way to find or validate the required cooling regime is presented. The paper then focuses on nozzle selection and presents laboratory measurements that provide accurate heat transfer coefficients as a function of position and surface temperature for different cooling configurations. Numerical simulations using the measured heat transfer coefficients allow the optimum design to be found for different product sizes.

In this study, the Bohler K 190 steel was used. The steel was manufactured by the powder metallurgy (PM) process. The boronizing process was carried out in the range of 1173 to 1323 K, for 1-10 h. The samples were boronized in solid medium, called the Durborid powder mixture. For the microstructural observations, the scanning electron microscopy was utilized for determining the morphology of interfaces and measuring the layers’ thicknesses. The phase composition of boride layers was also determined with X-ray diffraction analysis. To investigate the redistribution of chemical elements redistribution during the boronizing process, the EDS mapping and EDS point analysis were used. The boride layers were constituted by FeB and Fe2B phases except for 1173 K for 1 h. The values of Vickers microhardness of Fe2B, FeB and transition zone were estimated. Finally, to assess the boron activation energies in FeB and Fe2B, the so-called integral method was applied and the results in terms of activation energies were confronted with the literature data.

A large amount of steel slag (SS) and CO2 are generated in the steelmaking process. The indirect CO2 capture using SS is a promising way for co-treatment of the wastes. Ammonium salt solution is widely used to extract Ca2+ from the SS since it is recyclable. Several works have focus on improving the carbonation rate by adjusting various parameters (e.g., temperature and pH). However, there is little detail information about the associating behaviors and interaction strength between the various ions in the ammonia solution during the carbonation process. In this work, the Ca2+–CO32-–NH4+–Cl-–H2O system was established by using Material studio software. The effects of temperature and concentration of CO32- on CaCO3 growth were explored at the atomic scale by calculating the binding energy, mean square displacement, and diffusion coefficient between particles. Furthermore, the microstructure, bonding characteristics, and occurrence behavior of each particle were studied though molecular dynamics simulation methods. The results showed that with the increase of temperature (20–80 ℃), the binding ability and diffusion coefficients of Ca2+ and CO32- increase in the system, which is beneficial to the formation of CaCO3 clusters. With the increase of the concentration of CO32- (15–25 vol.%), the binding ability and diffusion coefficient of Ca2+ and CO32- in the system are enhanced, which is beneficial to the formation of CaCO3 clusters.

This paper presents the results of an experimental and analytical study on the behavior of cold-formed thick-walled steel plates connected by a single bolt under double shear. Experimental studies were conducted on a total of 54 bolted connections fabricated from two thickness of cold-formed thick-walled steel plates with the nominal thickness of 6 mm and 10 mm. The effects of end distance, edge distance and steel plate thickness were investigated on the bolt bearing behavior. Codes of (modified) ANSI/AISC 360-16 and EN1993-1-8 were applied to predict failure modes and bearing resistance of connections and the predictions were compared with that of measurements. A method was proposed to calculate the elongation of bolt hole at ultimate load. The studies show that fractures occurred on shear planes of specimens failed by shear out due to reduced ductility caused by cold forming process. The modified ANSI/AISC gives the most accurate predictions of failure modes and bearing resistance. However, the bearing resistance will be overestimated if the reduction in area of shear planes caused by occurrence of fracture is ignored for specimens with end distance being higher than 2.0d0 and a reduction factor is needed for calculating bearing resistance of connections. The method proposed in our paper can predict the elongation of bolt hole very well.

There is a fast-growing interest in the use of selective laser melting (SLM) for metal/alloy additive manufacturing. Our current knowledge of SLM printed 316 stainless steel (SS316) is limited and sometimes appears sporadic, presumably due to the complex interdependent effects of a large number of process variables of the SLM processing. This is reflected from the discrepant findings in the crystallographic textures and microstructures in this investigation with those reported in the literatures, which also vary itself. The as-printed material is macroscopically asymmetric in both the structures and crystallographic textures. The <101> and <111> crystallographic directions align parallel with the SLM scanning direction (SD) and build direction (BD), respectively. Like-wise, some characteristic low angle boundary features are reported crystallographic, while this investigation unequivocally proves them non-crystallographic since they always maintain an identical alignment with the SLM laser scanning direction irrespective of the matrix material’s crystal orientation. There is also 500±200 nm columnar or cellular features, depending on the cross-section, generally found all over the sample. These columnar or cellular features are formed with walls made of dense packing of dislocations entangled with Mn, Si and O enriched amorphous inclusions. They remain stable after the ASM solution treatments at 1050 °C temperatures, and therefore, are capable of hindering boundary migration events of recrystallization and grain growth. Thus, the nanoscale structures can be retained at high temperatures. Large 2-4 µm inclusions form during the solution treatment, within which the chemical and phase distribution are heterogeneous.

Hyper duplex stainless steels, HDSS, are a new alloy group of duplex stainless steels with the highest corrosion resistance and mechanical properties among the existing modern stainless steel. Due to the addition of extra high content of alloying elements, e.g. Cr, Ni, Mo, etc., the crystallization behavior of the δ-ferrite from the liquid is of vital importance for controlling the steel properties. In this work, the effect of cooling rate (i.e. 4°C/min and 150 °C/min) on the growth process of δ-ferrite in S33207 during the solidification process was investigated using high-temperature confocal scanning laser microscopy (HT-CLSM) in combination with electron microscopes and thermodynamic calculation. The results showed that the solidification mode of S33207 steel was a ferrite-austenite type (FA mode). L→δ transformation occurred at a certain degree of supercooling, and merging occurred during the growth of δ phase dendrites. Similar microstructures were observed after solidification under these two different cooling rates. The variation of area fraction of δ ferrite at the free surface and temperature as well as time during solidification of S33207 steels were calculated at different cooling rates of 4 °C/min and 150 °C/min, respectively. The current HT-CLSM study provides in-situ experimental evidence to confirm that a low cooling rate favored the growth of primary δ-ferrite, whereas a high cooling rate favored the nucleation of primary δ-ferrite during the solidification process. The post-microstructure as well as composition evolution is also briefly investigated. This work shed light on the real time insights for the crystallization behavior of hyper duplex stainless steels during solidification, which aims to contribute to the process control of manufacturing of this steel grade.

This paper mainly used database technology, machine learning, thermodynamic calculation, experimental verification, etc., on integrated computational materials engineering. The interaction between different alloying elements and the strengthening effect of precipitated phases are investigated mainly for martensitic ageing steels. Modelling and parameter optimization were performed by machine learning, and the highest prediction accuracy was 98.58%. Investigated the influence of composition fluctuation on performance and correlation tests to analyze the influence of elements from multiple perspectives. Furthermore, screen out the three-component composition process parameters with composition and performance with high contrast. Thermodynamic calculations studied the effect of alloying element content on the nano-precipitation phase, Laves phase, and austenite in the material. The heat treatment process parameters of the new steel grade were also developed based on the phase diagram. A new type of martensitic ageing steel was prepared by selected vacuum arc melting. The sample with the highest overall mechanical properties had a yield strength of 1887 MPa, a tensile strength of 1907 MPa, and a hardness of 58 HRC. The sample with the highest plasticity had an elongation of 7.8%. The machine learning process for the accelerated design of new ultra-high tensile steels was found to be generalizable and reliable.

In this study, we investigated the inhibiting effect of Dioscorea spp leaf extracts on the corrosion of mild steel in selected media using the weight loss method. The mild steel samples were pre-weighed and immersed in NaOH, NaCl and H₂SO₄ solutions respectively containing the leaf extracts, with the control samples immersed in solutions of the media containing no extract. The samples were allowed to stand for 672 hours, with a set of samples from each environment withdrawn at intervals of 168 hours for corrosion characterization. The results obtained from all the environments indicate that the corrosion rate increased as concentrations of Dioscorea spp increased. Results also confirmed that the extract was an effective and excellent inhibitor in the alkaline, salt, and acidic media. Conclusively it was proven that the higher concentration of Dioscorea spp leaf extracts in the media had the best inhibition characteristic on the mild steel in the selected environments. The results show good potential for application in manufacturing industries. The microstructure analysis of the various test coupons in the test media should be carried out to reveal the influence of adding the leaf extracts to the stimulated media on the grain structure distribution of the mild steel.

The organic coating of bridge steel girders is subjected to physical scratches, corrosion, and aging in natural weathering. The breakdown of the coating may cause serviceability and safety problems if left unnoticed. A hyperspectral imaging method is proposed to detect the condition of steel coatings based on coating-responsive features in reflectance spectra. A field test was conducted on the real-world bridge which shows obvious signs of degradation. The hyperspectral signature enables an assessment of the coating health and defect severity. The results indicated that the coating scratch can be effectively located in the domain of a hyperspectral image and the scratch depth can be determined by mapping a scratch depth indicator (SDI=R532nm / R641nm). Rust sources and products in steel girders can be identified by the unique spectral signatures and the rust stains (and thus stain areas) scattered on the coating can be pinpointed at pixel level by the corrosion rust indicators. The chemical integrity of a topcoat is demonstrated by the short-wave infrared spectroscopy and the topcoat degradation can be evaluated by the absorption at 8000 cm-1 and 5850 cm-1.

The paper focuses on two unconventional magnetic field-based treatment regimes applied to an alloyed steel before applying a thermochemical treatment. This study was conducted in order to improve the behavior of the chosen material during the wear process. Increasing the wear resistance and the micro-hardness of the superficial layer obtained from the treatments are a priority, as well as improving the mechanical properties of a Cr-Mo alloyed steel. Thermomagnetic treatment, applied before plasma nitriding treatment, improves the mechanical properties of the base material, especially in the case of a steel with a considerable chromium content (1,02%). This paper is a review of my own researches in the last years.

Super duplex stainless steel (SDSS) is used for manufacturing large valves and pipes in offshore plants because of its excellent strength and corrosion resistance. Large valves and pipes are manufactured by forging after casting, and the outside and inside microstructures are different owing to the difference in the cooling rate caused by the thermal conductivity. This microstructural variation causes cracks during solution annealing, which breaks the materials. To study toe corrosion resistance of the SDSS forged material, the microstructure was conducted based on the difference in the cooling rate between the inside and outside of the cast SDSS. To analyze the effects of the secondary phase fraction before solution annealing on the solution and corrosion resistance, the corrosion resistance with and without solution annealing was measured using the potentiodynamic polarization test and critical temperature test after the precipitation of the secondary phase. In the potentiodynamic polarization test, the secondary phase decreased the activation polarization and increased the corrosion rate. The critical pitting temperature exhibited the effect of the secondary phase.

The shield tunnels inevitably endure various damage with the service time increasing. Meanwhile, steel corrugated plate has been used extensively in multiple conditions and proved effective to strengthen the segmental joints by full-scale tests. A numerical model is proposed to probe the feasibility of using new Stainless Steel Corrugated Plate (SSCP) to reinforce the shield tunnel segments. A new method, called virtual tracking element technology, is employed to achieve the simulation of realistic stress state of the segmental joint. Moreover, the segmental joint component analysis and parametric study are conducted based on the numerical model. The results demonstrate that: (1) the virtual tracking element technology proves valid and efficient to simulate the secondary stress state of segmental joint; (2) SSCP reinforcement is not fully utilized when the grade of segmental concrete is C50 and it has abundant safety margin for potential overload; (3) SSCP reinforcement is well-performed regardless of the burial depth and reinforcement in advance is recommended.

This research is aimed to develop the method for damage degree evaluation in metals and alloys during their deformation and destruction based on acoustic emission (AE) technique. Experimental studies were carried out on tensile specimens of high-strength steel with simultaneous registration of AE signals in tested material. It was shown that the time-dependent AE primary parameters, such as the AE signal maximum amplitudes and AE activity, do not have a clear relationship with the material damage degree. This fact makes it difficult to use standard methods for assessing the damage degree of acoustic signal sources, including defects. It was proposed to use the Kolmogorov-Smirnov criterion to differ the processes of metal plastic deformation and crack propagation during the rupture. The possibility of estimating the material damage degree by high-energy AE hits share was shown. Besides, a particular expression was obtained for evaluating the damage degree for the material under study.

Aiming to diminish the defects caused by high-speed pulsed GMAW welding, such as non-penetration, non-fusion, humping and undercut, the paper proposed an improved twin-wire double-pulsed high-speed welding process by introducing the impact of additional shielding gas on the welding pool and the effects of different shielding gas flowrates on the microstructure and mechanical properties of the welded seam was investigated. The 2205 duplex stainless steel plate was used as the base material for the butt welding test, and the welded seams were subjected to tensile test, metallographic analysis, hardness analysis, and nondestructive testing. The results indicate that as the flowrate of additional shielding gas increases in the range of 8 L/min~16 L/min, the width of the welded seam increases and the height of reinforcement decreases gradually. However, a grooved seam with a lower middle region and higher sides will appear when the gas flowrate becomes excessively large. The test results indicate that the jet impact force is relatively moderate when the flowrate of the additional shielding gas is 12 L/min and thus, is optimal for the welded seam.

Features of nanosecond discharge development in a non-uniform electric field are studied experimentally. High spatial resolution imaging showed that thin luminous tracks of great length with a cross-section of a few microns are observed against the background of discharge glow in air and argon. It has been established that the detected tracks are adjacent to brightly luminous white spots on the electrodes or to the vicinity of these spots, and are associated with the flight of small particles. It is shown that the traces have various shapes and change from pulse to pulse. The particle tracks may look like curvy or straight lines. In some photos, they can change the direction of movement to the opposite. The particle trace was found to abruptly cut off and a bright flash is visible at the trail break point. The color of the tracks differs from that of the spark leaders, while the bands of the second positive nitrogen system dominate in the gap spectra during the existence of a diffuse discharge. Areas of blue light are evident near the electrodes, as well. Development of glow in the gap during its breakdown is revealed using an ICCD camera. Physical reasons for the observed phenomena are discussed.

This paper analyzed the main diseases of the friction high-strength bolt (FHSB) joints in order to study the characteristics of the corrosion products of the joints in steel bridge and the influence factors. Seven representative FHSB connection pairs and eight steel plate samples were selected from the Dongying Shengli Yellow River Bridge, which has been in operation for 33 years. Then Scanning Electron Microscope (SEM), Energy Dispersive Spectroscopy (EDS) and X-Ray Diffraction (XRD) were used to analyze the microscopic morphology and chemical composition of the corroded surface of the samples. Finally, this paper discussed the relationship between the corroded sample surface and the environmental corrosion. The research results showed that construction quality problems, such as non-standard hole expansion, segmental slab joint dislocation and contact surface pollution, accelerated corrosion of the contact surface. With the increase of corrosion degree of joints, the contact surface of aluminum spraying layer gradually changed from a rugged and dense state to a smooth and porous powder state. With the corrosion of the steel plate substrate, the contact surface gradually changed from a fluffy stratified state to a surface bonding state. It was inferred that the friction coefficient of the FHSB connection node on the corroded aluminum sprayed contact surface first decreased and then increased. The corroded node samples detected not only a large number of S and Cl elements, but also the oxides of Mn, Si and other elements as well as FeS. It was speculated that node corrosion was also related to atmospheric (acid rain) and industrial dust and other corrosive environments. Almost all samples detected the component SiO2 of the Yellow River soil, as well as Mg, Ca, K, Na and other elements at the same time, which is basically consistent with the component elements of the Yellow River soil. Therefore, it was inferred that it was related to the inclusion of the Yellow River soil.

The accumulation of steel slag and other industrial solid wastes has caused serious environmental pollution and resource waste. The resource utilization of steel slag is imminent. In this paper, alkali activated materials ultra-high performance concrete (AAM-UHPC) was prepared by replacing GGBFS powder with different proportions of steel slag powder, and its workability, mechanical properties, curing condition, microstructure, and pore structure were investigated. The results illustrate that the incorporation of steel slag powder can significantly delay the setting time and improve the flowability of AAM-UHPC, making it possible for engineering applications. The mechanical properties of AAM-UHPC showed a tendency to increase and then decrease with the increase of steel slag dosing, and reached the best performance at 30% dosage of steel slag. The maximum compressive strength and flexural strength are 157.1 MPa and 16.32 MPa, respectively. High temperature steam or hot water curing at early age was beneficial to the strength development of AAM-UHPC, but continuous high temperature hot and humid curing would lead to strength inversion. When the dosage of steel slag is 30%, the average pore diameter of the matrix is only 8.43nm, and the appropriate steel slag dosage can reduce the heat of hydration and refine the pore size distribution, making the matrix more dense.

Near-neutral pH and low redox potentials (EH) are considered favorable conditions for radionuclides immobilization in deep repository systems in clay geological formations. Cigeo is a future Industrial Centre for Geological Disposal for Nuclear Waste (NW) for high-level and intermediate level long-lived radioactive waste, to be built in France, at 500 m depth within the Callovo-Oxfordian clay formation. Deep knowledge of the mechanisms and kinetics of corrosion occurring at the external surface of tubings made of API 5L X65 carbon steel (CS-X65) in contact with COx pore water, is essential for a reversible NW management of the Cigeo site. By using robust handmade electrodes and electrochemical and gravimetric techniques, this work aimed to determine the corrosion phenomenology and kinetics of CS-X65 in contact with COx pore water flowing continuously through a Multi-Parameter Probe (MPP) device, placed at 500 m depth, for more than 180 days. It also aimed at demonstrating the reliability and the robustness of the measurement methodology for the corrosion evaluation of the metallic liner of the future nuclear waste disposal site. Two iron oxidants were encountered, oxygen, who was depleted, and proton, who was accompanied by hydrogen sulfide. Corrosion mechanisms and kinetics were well established for two CS-X65, electrochemically perturbed and not. The corrosion thickness loss rates stand between 0.016 and 0.032 mm/y.

Long-span steel structure trusses are widely used in factory buildings, but with the growth of service time and the increase of dynamic load fatigue, a considerable part of the long-span truss with dynamic load appears serious transverse cracks at the bottom of the middle span and oblique deformation of the abdomen in the operation process. The U-shaped cracks at the bottom and belly, as well as the mid-span down deflection of the main truss, reduced the functional function of the factory building truss structure, and had to limit the original crane load, which affected the normal safety and durability of the structure. Therefore, the application principle of the variable axial force cable system in the long-span factory building truss structure and 3D3S software modeling [1] were used. Analyzing and studying the reinforcement method of large-span powerhouse truss can provide practical experience for subsequent similar projects. In view of the above phenomenon, the large-span powerhouse trusses of Hongcheng Powerhouse 1 and No.2 located in Tonglu, Zhejiang Province are used as the research object, and the variable axial force cable method is proposed to strengthen and lift the load. Considering the span of large-span powerhouse truss, the cable system with 22m controlling force of 400kN is proposed to be selected for powerhouse 1, and the cable system with variable axial force of 24m is proposed to be selected for Powerhouse 2. The force model of large-span truss is established by using the finite element method commonly used to analyze the force of truss. Under two working conditions, The influence of reinforcement effect is analyzed and compared from three aspects: stiffness, bearing capacity and stability. And the phenomenon of uneven stress distribution is analyzed. The stress distribution characteristics of each node are understood by simulating the most disadvantageous node plates with the greatest internal force before and after reinforcement.

The literature has well established prestressing in concrete beams and its calculation procedures. However, its use in composite steel-concrete beams has increased despite main normative codes lacking a specific approach for it. Designers must, in most cases, combine the available criteria to calculate the standards of steel and reinforced concrete structures. This study aimed to formulate this optimization problem and analyze CO2 emissions for the optimal design of composite steel-concrete beams with external prestressing. The design variables for the optimization problem include cross-section of laminated or welded profiles, slab height, characteristic strength of concrete to compression, and number of tendons. We obtained a solution for the optimization problem via a genetic algorithm (GA) and a particle swarm optimization one (PSO). Comparative analysis with experimental example and with optimization problem of prestressed steel beam are performed. An parametric analysis to several spams is performed, which enabled to evaluate the factors that most impact CO2 emissions. According to results, the chosen algorithms effectively obtained solutions for the problem, and PSO usually provided better results than GA. Regarding the final solution composition, steel contributes the most to emissions, welded profiles provided better solutions than laminated ones, and laminated spans of up to 17.5m and welded ones up to 27.5m dispensed with tendons.

This article reports on the comparative study of the hot deformation behaviour of virgin (steel A) and rejuvenated heat treatment creep-exhausted (steel B) P91 steels. Hot uniaxial compression tests were conducted on the two steels at the deformation temperature range of 900°C-1050°C and a strain rate range of 0.01-10s-1 to 0.6 strain using Gleeble® 3500 equipment. The results showed that the flow stress largely depends on the deformation conditions. The flow stress for the two steels increased with an increase in strain rate at a given deformation temperature and vice versa. The flow stress-strain curves exhibited a dynamic recovery as the softening mechanism. The material constants determined using Arrhenius constitutive equations were: stress exponent was: steel A (5.76) and steel B (6.67), and the apparent activation energy was: steel A (473.1 kJ mol-1) and steel B (564.5 kJmol-1). From these results, steel A exhibited better workability than steel B. Statistical parameters analyses showed that the flow stress for the two steels had a good correlation between the experimental and predicted data. Pearson’s correlation coefficient (R) was: steel A (0.97) and steel B (0.98). The Average Absolute Relative Error (AARE) values were: 7.62% (steel A) and 6.54% (steel B). The study shows that the Arrhenius equations can effectively describe the flow stress behaviour of P91 steel, and this method is applicable to the industrial metalworking process.

Cold gas dynamic spray (CS) is a unique technique to deposit material using high strain rate solid state deformation. A major challenge for this technique is its dependence on the powder properties and lack of standards to assess them between lots and manufacturers. The motivation of this research was to understand the variability in powder atomization techniques for stainless steel powders and their subsequent properties for their corresponding impact on CS. A drastic difference (~30%) was observed in deposition efficiencies (DE) of unaltered, spherical, and similar sized stainless steel (316) powders produced using centrifugal (C.A) and traditional gas atomization (G.A) techniques. The study highlights more on differences on precursor level. Using recent advancements in large scale statistical measurements like laser diffraction shape analysis, µCT scanning, traditional methods like EBSD, nano-indentation, an attempt is made to understand the powder property. Insights on powder size and shape are documented. Significant differences were observed between C.A and G.A powders in terms of grain size, fraction of higher angle grain boundaries (HAGB) and nano hardness. The outcomes of this study would be helpful to understand the commercialization of the cold-spray process for bulk manufacturing of powder precursors

A steel damper column is an energy-dissipating member that is suitable for reinforced concrete (RC) buildings and multistory housing. To assess the seismic performance of buildings with steel damper columns, the peak displacement of the whole building and the energy dissipation demand of the dampers must be evaluated. This article proposes an energy-based prediction procedure for the peak and cumulative response of an RC frame building with steel damper columns. The proposed procedure considers two energy-related seismic intensity parameters, namely the maximum momentary input energy and the total input energy. The peak displacement is predicted considering the energy balance during a half cycle of the structural response, using the maximum momentary input energy. The energy dissipation demand of the dampers is then predicted considering the energy balance during a whole response cycle using the total input energy. The local responses (e.g., peak drift, maximum plastic rotation of beams, maximum shear strain, and energy dissipation demand of dampers) are predicted using pushover analysis. Numerical analysis results for 8- and 16-story RC buildings show that the proposed prediction method achieves satisfactory accuracy.

To provide carbon steel a long corrosion protection effect in NaCl solution with various pH, a pH-controlled intelligent inhibitor based on poly-acrylamide (PAM) and oleate imidazoline (OIM) was synthesized. SEM, FT-IR and TGA results indicating the OIM inhibitor was successfully loaded into PAM hydrogel with a very high content (39.64 wt%). The OIM release behavior from hydrogel structure have two stages, quickly release and sustained release. The pH of solution could affect the initial release kinetics of OIM inhibitor and the diffusion path in hydrogel structure. Weight loss measurement of L80 steel in different pH solution with OIM@PAM proved the inhibitor responsive release mechanism and an-ti-corrosion performance. The inhibition efficiency of OIM@PAM can maintain over 80% after long term immersion in harsh corrosive environment (pH 3), which is much higher than the inhibition efficiency of inhibitor in moderate corrosive solution.

In the field of metallurgy, there are many factors that influence the final quality of cast iron. These are mainly charge materials, chemical composition, metallurgical preparation up to the final casting process. Even small deviations from metallurgical processing lead to fluctuations in melt quality and the occurrence of casting defects. Charge materials has a significant impact on the quality of cast iron, especially steel scrap, which is increasingly used from an economic and ecological point of view, especially when melting cast iron in electric furnaces. Cast iron produced from a higher proportion of steel scrap in the charge has higher hardness and tensile strength. On the other side, these cast irons has a higher tendency to chillout, brittleness, shrinkage, pearlitic microstructure, stresses and higher purity due to the difference in hardness at different wall thicknesses of the castings. It is the high hardness that is the problem in the final machining of castings. These negative properties are recorded mainly in heavy thick-walled castings with higher tensile strength and hardness. This negative effect is mainly due to the nitrogen content in the steel scrap. Based on these knowledges, operating melts were realized in the foundry's operating conditions. The influence of steel scrap in the charge and the possibility of eliminating its negative effects on the properties of cast iron were investigated.

The most common long-term complication of silicone breast implants (SMI) remains capsular fibrosis. The etiology of this exaggerated implant encapsulation is multifactorial but primarily induced by the host response towards the foreign material silicone. Identified risk factors included specific implant topographies. Of note, breast implant-associated anaplastic large cell lymphoma (BIA-ALCL), has only been observed in response to textured surface implants. We hypothesize that reduction of SMI surface roughness causes less host response hence better cosmetic outcome with fewer complications for the patient. A total of 7 patients received the routinely used CPX®4 breast expander (~60 µM Ra) and the novel SmoothSilk® (~ 4 µM Ra), fixed prepectoral with a titanised mesh pocket and randomized to the left or right breast after bilateral prophylactic NSME (nipple-sparing mastectomy). We aimed to compare the postoperative outcome regarding capsule thickness, seroma formation, rippling, implant dislocation as well as comfortability and practicability. Our analysis shows that surface roughness is an influential parameter in controlling fibrotic implant encapsulation. First time intra-individually compared in patients, our data confirm an improved biocompatibility with minor capsule formation around SmoothSilk® implants with an average shell roughness of 4 µM and in addition an amplification of host response by titanised implant pockets.

Developing detailed Finite Element Models related to aerospace, automobile, civil, material science etc could be a very challenging task, especially generating a mesh that could produce accurate results. This review article provides an overview of different types of structural mechanics problems which are of interest to researchers and recent developments in meshing methodology related to each type of problems. The article also describes an automatic 2D mesh generation framework leverag- ing the capabilities of commercial FEA software MSC.PATRAN

CO₂ emissions have been identified as the main driver for climate change, with devastating consequences for the global natural environment. The steel industry is responsible for ca. 8%-11% of global CO₂ emissions, due to high fossil-fuel and energy consumption. The onus is therefore on industry to remedy the environmental damage caused and to decarbonise production. This desk research report follows a two-tiered route: 1) exploring the Bio Steel Cycle; 2) proposing a seven-step strategy to overcome the challenges within the iron and steel industry. The true levels of CO₂ emissions in the steelmaking process, during the blast-furnace/basic-oxygen-furnace operation, will be detailed first, at 4.61t of CO₂ emissions/t of steel produced. The manuscript proposes a solution for reduced carbon emissions steelmaking with the Bio Steel Cycle components and detail on how to reach net-zero carbon emissions steel production. The 7-step-implementation-strategy as a potential solution to achieve net and true zero carbon emissions steel production in the short to medium-term. The findings of this are pointing towards the conclusion that CO₂ emissions seem to have been under-reported and under-estimated in the past, but the emission can be addressed if the correct scenarios for net-zero steel manufacturing are implemented by 2050.

Steel slag is a co-product of the steelmaking industry, this material is rarely used as a binder due to its low cementitious properties. Thus, it´s believed that the alkaline activation of steel slag can enable its use as a cementitious material. This work has the objective of making a systematic bibliographic review on the theme "slag melt as a precursor in activated alkali binders". To this end, the ProKnow-C method was used for the selection and analysis of relevant research on the topic. The portfolio resulted in 71 texts, mostly journals paper. Bibliometrics showed that the country with the most publications is China and the journal with the most publications is Construction and Building Materials. The critical analysis concluded that the XRD, XRF, and compressive strength tests are the most used for the characterization of the material. It is possible to establish that there are some knowledge gaps on the subject, such as better mechanical characterization and greater production of works with dosing by the one-part method.

Groundwater (GW) flooding mechanisms differ from river flooding both spatially and temporally, and preventative methods against groundwater flooding must take this into account. Although groundwater flooding caused by river water rise occurs seldom, it can occasionally become severe and last for a long time if the river is significantly flooded. In the southwest portion of the research domain, Friedrichshafen with a few urban communities, the level of the groundwater table was discovered to be roughly 1 m below the surface. It was discovered that the urban settlement area only has one-story buildings. In the study region, it is typical for the single-story building's foundation bottom level to extend up to a depth of about 1.5 meters. Therefore, flood mitigation methods are taken into account for the southwest portion of the study region. The installation of a pumping well, drainage, and a barrier in the affected area are three different flood control strategies that are taken into consideration for the study area. From a technical and cost-benefit perspective, installing a pumping well that withdraws water and lowers the groundwater table was found to be the most effective flood control measure locally in a small region (e.g., 1km x 1km). By contrast, removing groundwater by building drainage and barriers was also shown to be ineffective to lower the groundwater table over an extended region and was significantly more expensive than the installation of wells. Additionally, when river flooding is taken into account compared to the default scenario where no intake of water from the river is included along the western border of the study area, it is discovered that the spread of pollution is significantly greater.

Background: Stoma closure is a widely performed surgical procedure, with 6295 undertaken in England in 2018 alone. This procedure is associated with significant complications; incisional hernias are the most severe, occurring in 30% of patients. Complications place considerable financial burden on the NHS; hernia costs are estimated at GBP 114 million annually. As recent evidence (ROCSS, 2020) found that prophylactic meshes significantly reduce rates of incisional hernias following stoma closure surgery, an evaluation of this intervention vs. standard procedure is essential. Methods: A cost-utility analysis (CUA) was conducted using data from the ROCSS prospective multi-centre trial, which followed 790 patients, randomly assigned to mesh closure (n=394) and standard closure (n=396). Quality of life was assessed using mean EQ-5D-5L scores from the trial, and costs in GBP using UK-based sources over a 2-year time horizon. Results: The CUA yielded an incremental cost-effectiveness ratio (ICER) of GBP 128,356.25 per QALY. Additionally, two univariate sensitivity analyses were performed to test the robustness of the model. Conclusion: The results demonstrate an increased benefit with mesh prophylaxis, but at an increased cost. Although the intervention is cost-ineffective and greater than the ICER threshold of GBP 30,000/QALY (NICE), further investigation into mesh prophylaxis for at risk population groups is needed.

Today's major challenge for smart Microgrids is to ensure the security of communications in a large number of changing data sets that are vulnerable to attacks by denial of services in constant evolution. The Internet Protocol Traceback defines a set of methods that help identify the source of an attack with minimal requirements for memory and processing. However, the concept of Traceback is not yet being used in smart Microgrids. As a result, the main challenge of this article is to incorporate a new Traceback approach into the cybernetic system of a smart mesh Microgrid, which can be tested using a network simulator (NS-3) based on delay, debit, and packet loss rate parameters. In fact, the simulation results show the efficacy of this approach compared to others existing in the literature. Furthermore, using the proposed Traceback technique and the mesh nodes, we were able to create a smart meshed Microgrid. Moreover, using the Traceback approach given for merging Intel Galileo Gen.1 nodes with the Compex WLE200NX.11a/b/g/n to establish a secure test bench, which is deployed as a prototype at the Sfax Digital Research Center in Tunisia, we were able to create an intelligent Microgrid. In fact, by identifying all attack vectors and revealing their origins, we could boost the efficiency of our operation by 100%.

This paper presents a computational approach designed to construct and query a literature-based knowledge graph for predicting novel drug therapeutics. The main objective is to offer a platform that discovers drug combinations from FDA-approved drugs and accelerates their investigations by domain scientists. Specifically, the paper introduced the following algorithms: (1) an algorithm for constructing the knowledge graph from drug, gene, and disease mentions in the biomedical literature; (2) an algorithm for vetting the knowledge graph from drug combinations that may pose a risk of drug interaction; (3) and two querying algorithms for searching the knowledge graph by a single drug or a combination of drugs. The resulting knowledge graph had 844 drugs, 306 gene/protein features, and 19 disease mentions. The original number of drug combinations generated was 2,001. We queried the knowledge graph to eliminate noise generated from chemicals that are not drugs. This step resulted in 614 drug combinations. When vetting the knowledge graph to eliminate the potentially risky drug combinations, it resulted in predicting 200 combinations. Our domain expert manually eliminated extra 54 combinations which left only 146 combination candidates. Our three-layered knowledge graph, empowered by our algorithms, offered a tool that predicted drug combination therapeutics for scientists who can further investigate from the viewpoint of drug targets and side effects.

Steel fibres provides ductility to concrete structures. This in turn gives possibility to replace or reduce conventional reinforcement in structural elements. In this study the focus is on structural walls and the fibres as potential replacement for horizontal reinforcement in areas where vertical re-bars are needed. An experimental study was conducted, in which prismatic specimens with longitudinal re-bars were subjected to centric loading. Ten samples with 12 specimens in each were tested. The parameters considered were: fibre content, concrete cover for the longitudinal bars, and presence of stirrups. Self-compacting concrete with 30 and 60 kg/m3 steel fibres was used. The influence of fibres on maximum load, stiffness, and ductility of the specimens is evaluated. The results show that fibres eliminated brittle collapse and spalling of concrete at failure. Samples with fibres tend to have reduced maximum force and stiffness but increased ductility. The specimens with fibre content of 60 kg/m3 showed more ductile behaviour than the ones with minimum amount of conventional stirrups. The study suggests that combination of steel fibres and conventional re-bars can lead to less qualitative compactness of the self-compacting concrete, which in turn may reduce load bearing capacity and stiffness of the structure.

This study is follow-up of the steel shot transformation under the influence of environmental factors research (Lisin et al., 2022) and is the initial stage of investigating the iron behavior in soils during steel shot corrosion under a number of factors: the metallic lead in soils, atmospheric precipitation, excess organic matter. The results obtained show that corrosion of steel ammunition is a continuous process, including the formation of a poorly soluble rust crust on the surface of the steel and the mineralization of the metal until it is destroyed. As a result, the metal transformed into rust form, is a constant source of iron ions and dispersed rust particles migrating in soil waters and accumulating in soils. In addition, the aggregation of corrosion products of steel ammunition is the cause of a change in physical and mechanical properties of soils, which leads to a violation of the air and water migration regime of soils and an increase in surface runoff from the territories of shooting activity. The highest environmental risks are observed when steel ammunition is used on shooting areas where metallic lead intensifies steel shot corrosion rate, while the deposited steel shot activates the deterioration of previously encapsulated metal and — if steel and lead ammunition are used at the same time — slows down the encapsulation of newly deposited metallic lead, which catalyses the accumulation and migration of lead in environmental components.

Despite significant advances in metallurgy and the potential to create high and very high-strength steel, all international specifications for steel design provided little information about the limits of slenderness for high-strength steel sections (HSSs) and didn’t give anything about the design of very high-strength steel sections (VHSSs). The American structural steel design specification covers circular hollow sections (CHS) of steel grades up to S690, while it isn't in ANSI/AISC 360-16 and ASTM A514/A514M. Euro code EN 1993-1-1 can be applicable only to steel grades up to S460. EN 1993-1-3 and EN 1993-1-12 contain supplementary rules for cold-formed members and HSS (S460- S700), respectively. Though ductility requirements for (HSS) are specifically established in EN 1993-1-12, it is largely a continuation of the normal-strength-steel design procedures standardized in EN 1993-1-1, where (HSSs) are largely treated as normal-strength steels in these rules, and the same design approaches are used. The behavior of high and very high-strength steel circular hollow sections under axial compression load is studied in this research. A total of 16 nonlinear finite-element (FE) models were generated to replicate stub column tests that were experimentally tested by others in previous research. Hence, a parametric study is conducted using forty FE models developed to investigate the local buckling behavior under various slenderness ratios comprehensively. The developed models cover slenderness ratios ranging from 20 to 1226 and steel grades S460 and S1100 with yield stress equal 460 MPa and 1152 MPa, respectively. The FE results were combined with 105 previously collected experimental results to assess the applicability of existing codified design methodologies in the Euro code and the North American codes of cold-formed CHS. Based on the results of this study, new cross-sectional slenderness limits and new design equations for more efficient simple designs were presented for high and very-high strength steel circular hollow sections and Compared with the results of experimental tests and FE models.

The cold-formed steel sections are becoming popular for different steel structures because it has a high resistance against the different straining actions with minimum weight compared with hard steel sections. Recently, the perforated cold-formed steel (PCFS) sections are used in many applications such as storage perforated uprights racks. Experimental research into the behaviour of steel storage rack uprights subjected to axial compression is presented in this paper. The material qualities of cold-formed steel uprights were determined by tensile tests. The seventeen perforated specimens were examined under axial compression, with five different cross-sections, three different web heights and thicknesses, and varying lengths. The study's goals are to find out how perforations affect the performance and failure mode of steel storage rack uprights, discuss the interaction of distortional and global buckling, and verify the accuracy of using the Direct Strength Method (DSM) for predicting the ultimate strength of uprights failing in buckling interactions for perforated uprights. It is found that the failure modes of perforated specimens with stiffeners generally cannot be well predicted by the Direct Strength Method. But when the modifications proposed by Xianzhong Zhao etc. al. are used, their accuracy is acceptable.

Zinc protection of galvanized steel is initially dissolved in alkaline solutions. However, passive layer is formed over time which protects the steel from corrosion. The behavior of galvanized steel exposed to strong alkaline solutions (pH values of 12.7) with a fixed concentration of sulfate ion of 0.04M is studied. Electrochemical measurement techniques such as corrosion potential, linear polarization resistance and electrochemical impedance spectroscopy are used. Synergistic effect of sulfate ion is also studied together with other anions such as chloride Cl- or bicarbonate ion HCO3- and with other cations such as calcium Ca2+, ammonium NH4+ and magnesium Mg2+. Presence of sulfate ions can depassivate the steel, leading to corrosion density of 0.3 µA/cm2 at the end of the test. The presence of other ions in the solution increases this effect. The increase in corrosion density caused by cations and anions responds to the following order (greater to lesser influence): NH4+&gt;Ca2+&gt;Mg2+ and HCO3- &gt;Cl- &gt;SO42-.

Particle deposition on the surface of the drying chamber poses the main drawback in the spray drying process, which reduces the product recovery and affects the quality of the product. In view of this, the potential application of chemical surface modification to produce a hydrophobic surface that reduces the powder adhesion (biofouling) on the wall of the drying chamber was investigated in this study. The hydrophobic Polydimethylsiloxane (PDMS) solution was used in the vertical dipping method at room temperature to determine the optimum coating parameters on borosilicate glass and stainless-steel substrates, which were used to mimick the wall surface of the drying chamber, to achieve highly hydrophobic surfaces. A single-factor experiment was used to define the range of the PDMS concentration and treatment duration using the Response Surface Methodology (RSM). The Central Composite Rotatable Design (CCRD) was used to study the effects of the concentration of the PDMS solution (X1, %) and the treatment duration (X2, hr) on the contact angle of the substrate (°), which reflected the hydrophobicity of the surface. A three-dimensional (3D) response surface was constructed to examine the influence of the PDMS concentration and treatment duration on the contact angle readings, which serve as an indicator of the surface's hydrophobic characteristic. Based on the optimisation study, the PDMS coating for the borosilicate glass achieved an optimum contact angle of 99.33° through the combination PDMS concentration: X1 = 1% (w/v) and treatment time X2 = 4.94 hr, while the PDMS coating for the stainless-steel substrate achieved an optimum contact angle of 98.31° with PDMS concentration: X1 = 1% (w/v) and treatment time X2 = 1 hr. Additionally, the infrared spectra identified several new peaks that appeared on the PDMS-treated surfaces, which represented the presence of Si-O-Si, Si-CH3, CH2, and CH3 functional groups for the substrates coated with PDMS. Furthermore, the surface morphology analysis using the Field Emission Scanning Electron Microscopy (FESEM) showed the presence of significant roughness and uniform nanostructure on the surface of PDMS-treated substrates, which indicated the reduction of wettability and the potential effect on unwanted biofouling on the spray drying chamber.

The steel damper column is an energy-dissipating member that is suitable for reinforced concrete (RC) buildings, and those used for multistory housing in particular. However, the effectiveness of steel damper columns may be affected by the behavior of surrounding members, and this effect can be severe in the case of seismic sequences. This article investigates the nonlinear response of building models having an RC moment-resisting frame (MRF) with and without steel damper columns under seismic sequences. The applicability of the concept of the momentary energy input to the prediction of the peak response of RC MRFs with damper columns under seismic sequences is also investigated. The main findings of the study are summarized as follows. (1) The peak response of RC MRFs with damper columns subjected to sequential accelerations is similar to the peak response obtained considering only the mainshock, whereas the cumulative strain energy of RC MRFs accumulates more for sequential accelerations. (2) The steel damper column is effective in reducing the peak and cumulative responses of RC MRFs in the case of sequential seismic input. (3) The relation of the hysteretic dissipated energy during a half cycle of the structural response and the peak displacement of the first modal response can be properly evaluated using the simple model proposed in this study.

Martensitic steels are used at a wide range of strength levels in environments which expose them to hydrogen or water vapor over a large range of partial pressures and temperatures. Hydrogen can cause catastrophic failures under many seemingly benign conditions. The effect of hydrogen on the dimension stability of high strength martensitic steels under such conditions has been poorly understood, and existing models do not seem to adequately account for it. Experiments were conducted to measure the variation in volume due to the uptake of hydrogen of such steels under near-ambient conditions, and the results were compared to theoretical estimates derived from the density of defects acting as hydrogen traps. Based on these results a new model for hydrogen embrittlement was developed. The hydrogen lattice dilation (HLD) model isolates volume expansion as a primary driver of hydrogen embrittlement. It provides and distinguishes two modes of failure acceleration: the fast, brittle, stress-intensity independent cracking under higher static crack loading, and a slower, highly stress-intensity dependent tearing mode at lower stress intensity. The relationship between the two is explained, as is how hydrogen absorption by defects accounts for the crack threshold and crack velocity of each.

The paper contains the results of the 100-hour test campaign of the Additive Manufactured (AM) spare part (retainer – slipper) dedicated for an exact axial piston pump. The material of the retainer-slipper has been identified by using energy dispersive spectroscopy and replaced by other – with similar material properties as the original one. The obtained spare part had been subjected to only one postprocessing type (sandblasting) to analyze the influence of the rough part after the AM process. The whole test campaign has been divided into stages, where after each stage microscopic measurements have been made. During microscopical investigation roughness and geometrical measurements were conducted. The results revealed that it is possible to replace parts in hydraulic pumps with the use of AM. 100-hour test campaign caused about 500% increase in the surface roughness of the pump’s original part which was cooperated with the AM spare retainer-slipper, without any damages to the test system.

An experimental study was carried out to evaluate the ductility of reinforced concrete beams longitudinally reinforced with hybrid FRP-Steel bars. The specimens were fourteen reinforced concrete beams with and without hybrid reinforcement. The test variables were bars position, the ratio of longitudinal reinforcement, and the type of FRP bars. The beams were loaded up to failure using a four-point bending test. The performance of the tested beams was observed using the load-deflection curve obtained from the test. Numerical analysis using the fiber element model was used to examine the growth of neutral axis depth due to the effect of test variables. The neutral axis curves were then used to further estimate the neutral axis angle and neutral axis displacement index. The test results show that the position of the reinforcement greatly influences the flexural behavior of the beam with hybrid reinforcement. It was observed from the test that the flexural capacity of beams with hybrid reinforcement is 4% to 50% higher than that of the beams with conventional steel bars depending on bars position and the ratio of longitudinal reinforcement. The ductility decreases as the hybrid reinforcement ratio (Af/As) increases. This study also showed that a numerical model developed can predict the flexural behavior of beams with hybrid reinforcement with reasonable accuracy.

This paper presents the results of an experimental study of the patterns of steel and lead shot transformation under the impact of environmental factors (two types of shot exposed alone and in combination with each other). The analyzed environmental factors include atmospheric precipitation of various acidity and soil solutions with a higher content of organic acids. This research demonstrated that steel shot is characterized by a high transformation rate that is an order of magnitude higher on average than the transformation rate of lead under the same conditions. The prevalence of the suspended iron form (excluding the interaction with organic acids) presents risks for such environmental components as soils and sediments and may be hazardous to the ambient air and natural waters in case of wind erosion and surface runoff from the catchment area. Furthermore, the joint presence of steel and lead shot mutually accelerates the corrosion of both metals, thus increasing the environmental risks.

This paper presents an algorithm for the fully automatic mesh generation for the finite element analysis of ships and offshore structures. The quality requirements on the mesh generator are imposed by the acceptance criteria of the classification societies as well as the need to avoid shear locking when using low degree shell elements. The meshing algorithm will be generating quadrilateral dominated meshes (consisting of quads and triangles) and the mesh quality requirements mandate that quadrilaterals with internal angles close to $90\degree$ are to be preferred. The geometry is described by a dictionary containing points, rods, surfaces and openings. The first part of the proposed method consist of an algorithm to automatically clean the geometry. The corrected geometry is then meshed by the frontal Delaunay mesh generator as implemented in the gmsh package. We present a heuristic method to precondition the cross field of the frontal quadrilateral mesher. Also the influence of the order in which the plates are meshed will be explored as a preconditioning step.

The demand for efficient processes through a comprehensive understanding and optimization of welding conditions continues to grow in the manufacturing industry. This study involves heat-resistant 2.25 Cr-1 Mo V-groove steel welding using the square-waveform alternating cur-rent. Experiments were conducted to build the relationship between input variables—such as current, frequency, electrode negativity ratio, and welding speed—and process performance, such as penetration, bay area, deposition rate, melting efficiency, percentage dilution, flux–wire ratio, and heat input. The process was analyzed in light of the defect-free high-deposition weld groove weld, the sensitivity to process parameters, and the optimization and development of the process map. The study proposes an innovative approach to reducing the cost and time of optimizing the one-pass-each-layer V-groove welding process using bead-on-plate welds. Square waveform welding creates a metallurgical notch in the form of a bay at the fusion boundary that can be minimized by selecting appropriate welding conditions. The square waveform submerged arc welding is more sensitive towards changes in current and welding speed than the frequency and electrode negativity ratio; however, the electrode negativity ratio and frequency are minor but helpful parameters to achieve optimal results. The proximity of the planned and experimental results to within 3% confirms the validity of the proposed approach. The investigation shows that 90% of the maximum deposition rate is possible for one-pass-each-layer V-groove welds within heat input and weld width constraints.

This article deals primarily with the problem of determining the cutting force when machining hardened steels. Secondary issues are focused on the evaluation of surface quality on machined samples and the recommendation of cutting conditions. A wide variety of components are used in engineering, the final heat treatment of which is hardening. These components are usually critical in a particular product. The quality of these components determines the correct functioning of the entire technical equipment and ultimately its service life. In our case, these are the core parts of thrust bearings, specifically the rolling elements. The subject of the experiment is machining these components in the hardened state with cubic boron nitride tools and continuous measurement of the cutting force using a dynamometer. The following evaluation assesses the surface quality by both touch and non-touch methods. A structural equation with appropriate constant and exponents was then constructed from the data obtained using the dynamometer.

H-adaptivity is an effective tool to introduce local mesh refinement in FEM-based numerical simulation of crack propagation. The implementation of h-adaptivity could benefit the numerical simulation of fatigue or accidental load scenarios involving large structures such as ship hulls. In engineering applications, the element deletion method is frequently used to represent cracks. However, the element deletion method has some drawbacks such as strong mesh dependency and loss of mass or energy. In order to mitigate this problem, the element splitting method could be applied. In this study, a numerical method called ‘h-adaptive element splitting’ (h-AES) is introduced. The h-AES method is applied in FEM programs by combining h-adaptivity with the element splitting method. Two examples using the h-AES method to simulate cracks in large structures under linear-elastic fracture mechanics scenario are presented. The numerical results are verified against analytical solutions. Based on the examples, the h-AES method is proven to be able to introduce mesh refinement in large-scale numerical models that consist of structured coarse meshes. By employing the mesh refinement introduced in this paper, very small cracks are well represented in large structures.

Three-dimensional reconstruction plays an important role in assisting doctors and surgeons in diagnosing bone defects’ healing progress. Common three-dimensional reconstruction methods include surface and volume rendering. As the focus is on the shape of the bone, volume rendering is omitted. Many improvements have been made on surface rendering methods like Marching Cubes and Marching Tetrahedra, but not many on working towards real-time or near real-time surface rendering for large medical images, and studying the effects of different parameter settings for the improvements. Hence, in this study, an attempt towards near real-time surface rendering for large medical images is made. Different parameter values are experimented on to study their effect on reconstruction accuracy, reconstruction and rendering time, and the number of vertices and faces. The proposed improvement involving three-dimensional data smoothing with convolution kernel Gaussian size 0.5 and mesh simplification reduction factor of 0.1, is the best parameter value combination for achieving a good balance between high reconstruction accuracy, low total execution time, and a low number of vertices and faces. It has successfully increased the reconstruction accuracy by 0.0235%, decreased the total execution time by 69.81%, and decreased the number of vertices and faces by 86.57% and 86.61% respectively.

The present study utilizes a metal inert gas welding (MIG) to make a dissimilar weld joint of different stainless steel grades AISI 304, 314, 316L, 420 and a standard structural steel S355MC to estimate the correlation of a microstructure and the mechanical properties. The microstructure of the base metals (BM), the heat affected zone (HAZ), the fusion zone (FZ) and the weld seam were analyzed using optical microscopy. Optical microscopy did not reveal any presence of weld defects such as porosity or cracks. The analysis of microstructure showed that both the austenitic and martensitic stainless steel weld structures contain some retained delta ferrite and coarse Me23C6 carbides in the HAZ, while the FZ exhibits delta ferrite and some retained austenite. The hardness profiles revealed difference between austenitic and martensitic steel welds that the later showed extremely high values in the HAZ (~500 HV/0.1) which causes fracture in this zone. The welds of all austenitic steel grades withstood tensile test, showing the average tensile strength of 472 MPa with fracture observed in the base metal zone. It made clear that the use of a filler rod 308LSI is suitable only for the austenitic stainless and structural steel dissimilar welds, and not appropriate for martensitic-structural steel welds. The achieved results revealed that the higher hardness of the martensitic phase in the HAZ of AISI 420 is closely related with the formation of untempered coarse martensitic structure and higher carbon content.

Fires are complex multi-physics problems that span wide spatial scale ranges. Capturing this complexity in computationally affordable numerical simulations for process studies and “outer-loop” techniques (e.g., optimization and uncertainty quantification) is a fundamental challenge in reacting flow research. Further complications arise for propagating fires where a priori knowledge of the fire spread rate and direction is typically not available. In such cases, static mesh refinement at all possible fire locations is a computationally inefficient approach to bridging the wide range of spatial scales relevant to fire behavior. In the present study, we address this challenge by incorporating adaptive mesh refinement (AMR) in fireFoam, an OpenFOAM solver for simulations of complex fire phenomena involving pyrolyzing solid surfaces. The AMR functionality in the extended solver, called fireDyMFoam, is load balanced, models gas, solid, and liquid phases, and allows us to dynamically track regions of interest, thus avoiding inefficient over-resolution of areas far from a propagating flame. We demonstrate the AMR capability and computational efficiency for fire spread on vertical panels, showing that the AMR solver reproduces results obtained using much larger statically refined meshes, but at a substantially reduced computational cost. We then leverage the computational efficiency of the AMR solver to demonstrate an optimization framework for fire suppression based on the open-source Dakota toolkit.

This paper reviews how dynamically adaptive wavelet methods can be designed to simulate atmosphere and ocean dynamics in both flat and spherical geometries. We highlight the special features that these models must have in order to be valid for climate modelling applications. These include exact mass conservation and various mimetic properties that ensure the solutions remain physically realistic, even in the under-resolved conditions typical of climate models. Particular attention is paid to the implementation of complex topography in adaptive models. Using \textsc{wavetrisk} as an example, we explain in detail how to build a semi-realistic global atmosphere or ocean model of interest to the geophysical community. We end with a discussion of the challenges that remain to developing a realistic dynamically adaptive atmosphere or ocean climate models. These include scale-aware subgrid scale parameterizations of physical processes, such as clouds. Although we focus on adaptive wavelet methods, many of the topics we discuss are relevant for adaptive mesh refinement (AMR).

The article presents a modified finite element (FE) based algorithm for nonlinear analysis of 2D beam structures, which takes into account the influence of the shear forces. The method proposed enables using complex materials with nonlinearities without the need of implementing advanced constitutive models in FE routines. It can be directly integrated with commonly available FE software for linear analysis of beam structures, so its functionality can be easily extended also with material nonlinearities. The presented approach adopts the generalized constitutive law algorithm to iteratively modify the stiffness of beam element. To address an influence of a shear stiffness, a Timoshenko beam element was used. The methodology was implemented and its performance was verified on several numerical examples. For validation, the displacements and the ultimate loads were compared with the values from a commercial FE software. The results shown a good correlation between the reference model and the method proposed.

The corrosion morphology in grade 2205 duplex stainless steel wire has been studied to understand the nature of pitting and the causes of the ferrite phase's selective corrosion in acidic NaCl solution. It is shown that the corrosion mechanism is always pitting, which either manifests lacy cover perforation or densely-arrayed selective cavities developing on the ferrite phase. Pits with a lacy metal cover form in concentrated chloride solutions, whereas the ferrite phase's selective corrosion develops in diluted electrolytes, showing dependency on the chloride-ion concentration. The pit perforation is probabilistic and occurs on both austenite and ferrite grains. The lacy metal covers collapse in concentrated solutions but remain intact in diluted electrolytes. The collapse of the lacy metal cover happens due to hydrogen embrittlement. Pit evolution is deterministic and occurs selectively in the ferrite phase in light chloride solutions.

Multiaxial fatigue experiments under asynchronous loadings with four different loading frequency ratios were carried out on 30CrMnSiA steel. The experimental results show that the fatigue life decreases when the axial or torsion frequency increases from 1 to 2, while there is no significant change when the axial or torsion frequency increases from 2 to 4. The surface crack paths are observed and show that cracks initiate on the maximum shear stress amplitude planes, propagate approximately tens of microns, and then turn to propagate along the maximum normal stress planes. The number of secondary cracks increases when the axial or torsion frequency increases. Subsequently, the Bannantine-Socie and Wang-Brown cycle counting methods along with various multiaxial fatigue criteria and Palmgren-Miner’s cumulative damage rule were used for fatigue life prediction. The experimental results are consistent with the fatigue life predicted by the Bannantine-Socie method with the section critical plane criterion for 30CrMnSiA steel under asynchronous loading paths.

The change in the value of the breaking energy is discussed here for selected steel grades used in building structures after subjecting the samples made of them to episodes of heating in the steady-state heating regime and then cooling in a simulated fire conditions. These changes were recorded based on the instrumented Charpy impact tests, in relation to the material initial state. The S355J2+N, 1H18N9T steels and also X2CrNiMoN22-5-3 duplex steel were selected for detailed analysis. The fire conditions were modelled experimentally by heating the samples and then keeping them for a specified time at a constant temperature of: 600°C (first series) and 800°C (second series), respectively. Two alternative cooling variants were investigated in the experiment: slow cooling of the samples in the furnace, simulating the natural fire progress, without any external extinguishing action, and cooling them in water mist simulating an extinguishing action by a fire brigade. The temperature of the tested samples was set at the level -20oC and alternatively at the level + 20oC. The conducted analysis is aimed at assessing the risk of sudden, catastrophic fracture of load-bearing structure made of steel degraded as a result of a fire previously occurred with different development scenarios.

High-strength low-alloy steels (HSLAs) are widely used in the structural body components of many domestic motor vehicles owing to their better mechanical properties and greater resistance. The real production process of HSLA steelmaking can be regarded as a model that builds on the relationship between process parameters and product quality attributes. A surrogate modeling method is used, and the resulting production process model can be applied to predict the optimal manufacturing process parameters. We used different methods in this paper to build such a surrogate model, including linear regression, random forests, support vector regression, multilayer perception, and a simplified VGG model. We then applied three bio-inspired search algorithms, namely particle swarm optimization, the artificial bee colony algorithm, and the firefly algorithm, to search for the optimal controllable manufacturing process parameters. Through experiments on 9,000 test samples used for building the surrogate model, and 299 test samples for making the optimal process parameter selection, we found that the combination of a simplified VGG model and the firefly algorithm was the most successful at reaching a success rate of 100%—in other words, when the product quality attributes of all test samples satisfy the mechanical requirements of the end products.

The article presents results of research consisting in an attempt to assess the influence of temperature, heating time and cooling method on microstructure and residual strength properties of steel previously tempered during the production process. Simulated environmental conditions to which high-strength bolts, commonly used in steel construction, were subjected, were intended to reflect conditions of a natural fire that may occur in public facilities where the obligation to ensure safety of users and rescue teams is of key importance, also required by law. Furthermore, the tests carried out also comprised a simulated effect of a rescue and firefighting operation using shock, rapid cooling of some of the heated bolts. Samples cut out from the tested bolts, after they were properly prepared, were subjected to microstructural tests using light microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), phase analysis with the use of an X-ray diffractometer (XRD) and quantitative analysis of the microstructure involving, inter alia, measuring the surface area of grains, their equivalent diameter and mean diameter. As a result of the tests, considerable microstructure changes were identified occurring in the bolt material as a result of exposing it to fire conditions, leading to a change in key, from the point of view of structural safety, mechanical properties. The results of the microstructure tests were compared with the results of previous strength tests, including hardness of the material after the heat treatment and the residual tensile strength of the material Rm. A conducted comparative analysis showed a significant effect of all such factors as the temperature level of the simulated fire, its duration and the fire-fighting method on the mechanical properties of bolts. Results obtained were provided with required comments and the concept of using the microstructure for the post-fire assessment of steel structures was referred to.

The energy transfer process of laser selective melting is very complex. To study the effect of la-ser selective melting on the microstructure and properties of 18Ni-300 martensitic steel, ABAQUS was used to simulate the temperature of laser cladding 18Ni-300 martensitic steel at different time points and different laser power. The results show that the cross-section shape of the molten pool changes from round to oval With the increase of laser power, the higher the peak value of temperature time curve, the greater the temperature gradient; and the laser clad-ding experiment of 18Ni-300 martensitic steel was carried out, and the microstructure and me-chanical properties of the samples under different laser power were analyzed. The results show that with the increase of laser power, the grain size of the cladding layer becomes smaller and the microstructure becomes more compact; the hardness of the side surface of the sample is higher than that of the upper surface, and the tensile strength and elongation show a trend of first increasing and then decreasing.

The dilatometer curves of continuous cooling transformation of 12Mn steel were measured with Formastor-FⅡthermal mechanical simulator．The steel's undercooled austenite phase continuous cooling transformation curves ( CCT curves) were established by means of the dilatometer method and the metallographic-hardness measurement method． The effect of cooling rate on microstructure and hardness of the steel was studied． CCT curve of test steel was simulated by JMatPro. The results show that the Ac1 and Ac3 of the experimental steel are 692 ℃ and 855 ℃ ; the microstructure obtained is made of ferrite，pearlite and bainite．The ferrite transformation and pearlite transformation occur at a slower cooling rate，in which the ferrite is dominant. When the cooling rate is greater than 4.25 ℃ / s bainite transformation happens．As the cooling rate increases，microstructure or grains become finer．The hardness of the tested steel with increasing cooling rate shows a trend of first fast increase and soon decrease．The simulation results are consistent with the measured CCT law. The high temperature mechanical properties of 12mn steel round billet were tested by gleeble-1500d thermal / mechanical simulator. The tensile strength, reduction of area and stress-strain curves of the billet were obtained in the range of 600-1300 ℃.

In this study, the effect of hot stamping forming process on the properties change of compound layer in Al–Si coated high-strength steel sheet with different thickness was investigated. The coating layer in hot stamped high-strength steel sheet was composed of a diffusion layer and a compound layer. As the hot stamping temperature and holding time for forming increased, the thickness of the compound layer in the Al–Si coated high-strength steel sheet increased. The thickness of coating layer with the hot stamping for 500 sec at 890, 910 and 950 °C was obtained 8.9, 11.8, and 20.6 micrometer, respectively. The thickness of coating layer with hot stamping for 180, 500 and 550 sec at 910 ^oC was obtained 5.7, 11.8, and 17.8 micrometer, respectively. The compound layer in hot stamped high-strength steel sheet with Al–Si coating layer consists of Al_5.4Fe₂ and Fe₂Si phases. In the compound layer, Al and Si were irregularly distributed.

Turbulent flow is the first and fundamental physical phenomena to evaluate when optimising cost and reducing emissions from an Anode Baking Furnace (ABF). Gas flow patterns, velocity field, pressure drop, shear stress, and turbulent dissipation rate variables are the main operational parameters to be optimised, considering a specific geometry. Computational Fluid Dynamics (CFD) allows simulating physical phenomena using numerical methods with computer resources. In particular, the finite element method is one of the most used methods to solve the flow equations. This method requires a discretisation of the geometry of the ABF, called mesh. Hence, mesh is the main input to the finite element method. A suitable mesh for applying a discretisation method determines whether the problem can be simulated or not. Generating an appropriate mesh remains a challenge to perform accurate simulations. In this work, a comparison between meshes generated using two mesh generation tools is presented. Results of different study cases are included.

Keyhole laser beam welding (LBW) of stainless steel sheets with a gap in between is numerically simulated with a three-dimensional, transient multi-physical model for laser material processing. At first, the model’s ability to reproduce experimental results on a relatively coarse computational mesh within reasonable computing time, so as to serve as process optimization tool, is presented. An example of process optimization, where a given set of weld seam quality criteria is fulfilled by iteratively optimizing a secondary laser beam, is shown. The relatively coarse mesh, in combination with a good model calibration to the experimental conditions, allows for sufficiently fast simulations to use this approach for optimization tasks. Finally, using a finer spatial and temporal discretization, the dynamic processes in the vicinity of the keyhole leading to the formation of pores are investigated. The physical phenomena predicted by the simulation are coherent with experimental observations found in literature.

The preservation of the authenticity of a building artefact is a responsible practice. On the other side, the need to save the building artefact from the natural and anthropic degradation, to ensure the structural reliability to the different actions, to define an efficient maintenance program are big challenges, that involves the cooperation of several professionals, responsible use of innovative techniques and materials that are nowadays available. This paper focuses on a specific design approach for the rehabilitation works of ancient constructions in archaeological sites. The proposed conceptual design approach implies different steps that allow the optimization of the design at an increasing level of knowledge on the existing structures and their materials. The design procedure on historical constructions generally includes the following steps: the collection of data, the structural identification, hazard, and vulnerability analysis, damage and risk analysis, a cost-benefit analysis, so only at the end of the process, the final design is achieved. In the archaeological area, some important design aspects cannot be defined before the execution work phase, since some elements could be revealed and identified during work execution, as a consequence, the final design has been often optimized after all this information has been acquired. A studied case in the archaeological site of Pompeii is herein presented to prove the efficiency of the proposed approach.

Currently, one of the biggest issues when developing an ODS alloy is the competition established between the different oxide precursors during the precipitation of oxides which nature depends on their chemical composition. In the presence of various precursors, usually the one with the highest affinity to oxygen leads to the absence of the other oxides. In this work, a new process to equilibrate the local concentration of species and to decrease the competition among them is explained. A unique compound, containing the diverse oxide precursors as one complex oxide, is introduced in a prealloyed 14Cr Steel powder via mechanical alloying. Thus, generating environments enriched in Y, Ti and Zr which, after consolidation, refine the oxides precipitation improving the thermal stability of the alloy. SPS were used as consolidation technique to guarantee shorter sintering times and to maintain the nanostructure obtained. Mechanical properties were tested by tensile tests and Vickers microhardness.

This paper deals with a non-standard finite difference scheme defined on a quasi-uniform mesh for approximate solutions of the Magneto-Hydro Dynamics (MHD) boundary layer flow of an incompressible fluid past a flat plate for a wide range of the magnetic parameter. We show how to improve the obtained numerical results via a mesh refinement and a Richardson extrapolation. The obtained numerical results are favourably compared with those available in the literature.

The purpose of this study is to analyse the feasibility of using waste from granite gang saws (GCW-GS) to manufacture ultra-high performance, steel-fibre reinforced concrete (UHPFRC). These machines cut granite blocks by abrasion using a steel blade and slurry containing fine steel grit. The waste generated by gang saws (GCW-GS) contains up to 15% Fe2O3 and up to 5% CaO. This is the main difference from the waste produced by diamond saws (GCW-D). Consequently, the second objective of this study is to compare the results of the waste obtained with gang saws with that from diamond saws, in order to determine the influence of iron and calcium oxides. The waste from cutting granite with gang saws was used in different percentages to replace micronized quartz powder of natural origin in the manufacture of UHPRFC. All the test specimens were analysed to determine their compressive strength, elasticity modulus, flexural strength and indirect tensile strength. The final conclusion is that wastes from both gang saws and diamond saws can be used to manufacture UHPFRC with an improvement in the mechanical properties up to a 35% replacement. The results for GCW-GS are better, mainly due to the pozzolanic effect of the iron dioxide. For higher percentage replacements the mechanical properties are close to the control concrete with small decreases.

Selective laser melting (SLM) is a commonly used laser powder bed technique where the final properties are influenced by many different powder related properties, such as particle size distribution, chemical composition and flowability. In applications where high hardness, wear resistance, strength and good heat properties are required, high speed steels (HSS) are widely used today. HSS has high carbon content and are therefore considered as unweldable. The rapidly growing implementation of AM technologies has led to a growing range of new applications and demands for new alloys and properties. The interest in being able to manufacture HSS by SLM without cracking is therefore increasing. In SLM, it is possible to preheat the base plate to a few hundred degrees Celsius which has been used for HSS and proved successful due to reduced thermal gradients. In this study, the properties of SLM produced high speed steel PEARL Micro®2012 with a carbon content of 0.61 wt.-% have been investigated and compared to those of a forged and rolled PM-HIP counterpart ASP®2012.

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.

This study addresses an alternative use of viscous dampers (VDs) associated with buckling restrained braces (BRBs) as the innovative seismic protection devices. For this, 4, 8 and 12 storey steel frames were designed with 6.5 m equal span length and 4 m storey height. Thereafter, the VDs and BRBs were placed over the height of each frame considering three different configurations. The structures were modeled using SAP2000 finite element program and evaluated by the nonlinear time history analyses subjected to the six natural accelerograms (1976 Gazlı, 1978 Tabas, 1987 Superstition Hills, 1992 Cape Mendocino, 1994 Northridge and 1999 Chi-Chi). The structural response of the structures with and without VDs and BRBs were studied in terms of variation in the displacement, interstorey drift, absolute acceleration, maximum base shear, time history of roof displacement. The results clearly indicated that the application of VDs and BRBs had remarkable improvement in the earthquake performance of the case study frames by reducing the local/global deformations in the main structural systems and satisfied the serviceability.

This article discusses the issue of hardened steel machining. Many components in the engineering industry use hardening as the final heat treatment. These components usually occupy a significant position in a given assembly unit. They guarantee the correct operation of the entire technical equipment in total cooperation with other components. The quality of these components depends on the integrity of their surface. The production of these parts is usually carried out by traditional technological procedures. An example of such a technology is clearly grinding. However, this article discusses the application of other finishing technologies using tool material made of cubic boron nitride (CBN). The technology used is finishing turning with subsequent tumbling technology. The subject of the evaluation is the integrity of the surface. In this part of the experiments, there are mainly individual parameters of surface roughness. Compared components are bearing rings, in this case the inner surface of the housing ring.

A phosphate/molybdate and cerium-modified phosphate/molybdate conversion coatings were deposited on a carbon steel surface and their protective and self-healing abilities were evaluated. Surface morphology and inner structure of the coatings were examined using FE-SEM-FIB and TEM techniques, chemical composition and element distribution depth profiles in conversion layers were determined using EDX measurements, whereas XPS was applied for the analysis of Mo and Ce oxidation states. Voltammetric measurements and EIS were performed to assess the corrosion behavior of the samples. The higher protective and stronger self-healing abilities were found for phosphate/molybdate/cerium conversion coating deposited in a sulphate-containing solution. This was attributed to higher values of both: total cerium and Ce(IV) content in the conversion layer as well as to lower number of structural defects in the coating. It was demonstrated that the micro-structural characteristics of protective coatings are also important in determining self-healing abilities.

The effect of rare earth Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results showed that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites, and significantly improve the toughness of weld metal. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. However, excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties, and the corresponding values were 835MPa of tensile strength and 72 J of impact toughness. These findings suggest that the control of Pr6O11 can be an effective way to improve the impact toughness of weld metal.

The effect of Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results demonstrate that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites in the weld metal, and significantly improve the toughness. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. Excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties.

The aim of this work was to investigate the microstructure and the mechanical properties of la-ser-welded joints combined of DP800 and DP1000 high strength thin steel sheets. The welded joints (WJ) comprised of similar/dissimilar steels with similar/dissimilar thickness were consisted of different zones and exhibited similar microstructural characteristics. The trend of microhard-ness for all WJs was consistent, characterized of the highest value at hardening zone (HZ) and lowest at softening zone (SZ). The degree of softening was more severe and the size of SZ was wider in the WJ combinations of DP1000 than DP800. The tensile test fractures were located at the base material (BM) for all DP800 weldments, while the fractures occurred at the fusion zone (FZ) for the weldments with DP1000 and those with dissimilar sheet thicknesses. The DP800-DP1000 weldment presented similar yield strength (YS) and ultimate tensile strength (UTS) values but lower elongation (EI) in comparison with the DP800-DP800 weldment, which showed similar strength properties as the BM of DP800. However, the EI of DP1000-DP1000 weldment was much lower in comparison with the BM of DP1000. The DP800-DP1000 weldment with dissimilar thicknesses showed the highest YS and UTS values compared with the other weldments, but with the lowest EI. The fatigue fractures occurred at the WJ for all types of weldments. The DP800-DP800 weldment had the highest fatigue limit and DP800-DP1000 with dissimilar thick-nesses had the lowest fatigue limit. The fatigue crack initiated from the weld surface.

Three kinds of Ni based alloy cladding coatings were prepared on 316L stainless steel at different power. The microstructure of the cladding layer was observed and analyzed by XRD, metallographic microscope and SEM. The hardness of the cladding layer was measured, and the wear resistance of the cladding layer was tested by friction instrument. The results show that the effect of laser cladding is good and the cladding layer has a good metallurgical bonding with the substrate. Different microstructures such as dendritic and equiaxed grains can be observed in the cladding layer. With the increase of laser power, more equiaxed and columnar dendrites can be observed. The phase composition of the cladding layer is mainly composed of γ - Ni solid solution and some intermetallic compounds such as Ni3B, Cr5B3 and Ni17Si3. The results of EDS show that there are some differences in the distribution of C and Si between dendrites. The hardness of the cladding layer is about 600 HV0.2, which is about three times of the substrate (~ 200 HV0.2). Through the analysis of the wear morphology, the substrate wear is serious, there are serious shedding, mainly adhesive wear and abrasive wear. However, the wear of cladding layer is slight, which is abrasive wear, and there are some grooves on the surface.