The effect of Localized Surface Plasmon (LSP) of 5 nm mean size Au particles deposited on TiO2 P25 was investigated during the photo-thermal water gas shift reaction (WGSR). The effects of CO concentration, excitation light flux and energy, and molecular oxygen addition during the reaction were investigated. The photocatalytic WGSR rate under light excitation with wavelengths extending from 320 to 1100 nm was found to be higher than the thermal reaction alone at the same temperature (85 oC). A ratio H2/CO2 of near unity was found at high concentrations of CO. Addition of molecular oxygen during the reaction resulted in a slight decrease of molecular hydrogen production while the rates of CO2 formation and that of CO consumption changed by one order of magnitude. More important, it was found that the WGSR rates were still high under only visible light excitation (600 - 700 nm). The results prove that Au LSP alone triggers this chemical reaction without the need to excite the semiconductor on which they are deposited.

As a photo-catalytic titanium oxide film deposition process, thermal spray is hoped to be utilized practically on the condition that it is relatively easy to deposit anatase rich films. However, because of its high equipment and feedstock powder costs, it is very difficult to introduce thermal spray equipment into small companies. In this study, to develop a low cost thermal spray system, low power atmospheric suspension plasma spray equipment with titanium hydroxide suspension created by hydrolysis of titanium tetra iso butoxide using Ar, N2 as working gases. For avoiding sedimentation of the hydroxide particles in the suspension, mechanical milling of the suspension was conducted to create colloidal suspension before using it as feedstock. Moreover, an Ultrasonic wave container was used to keep the suspension particles moving while the spray process was conducted. After the film deposition, with As for the coating, anatase rich TiO2 film could be obtained. For characterization of the film, microstructure observation by optical microscope and X-ray diffraction was carried out. Consequently, by creation of colloidal suspension, deposition could be conducted without sedimentation of the hydroxide particle in the suspension during operation. Besides, it was proved the film had enough photo-catalytic property to decolor methylene-blue droplet

Shale gas production is associated with significant usage of fresh water and discharge of wastewater. Consequently, there is a necessity to create the proper management strategies for water resources in shale gas production and to integrate conventional energy sources (e.g., shale gas) with renewables (e.g., solar energy). The objective of this study is to develop a design framework for integrating water and energy systems including multiple energy sources, cogeneration process, and desalination technologies in treating wastewater and providing fresh water for shale gas production. Solar energy is included to provide thermal power directly to a multi-effect distillation plant (MED) exclusively (to be more feasible economically) or indirect supply through a thermal energy storage system. Thus, MED is driven by direct or indirect solar energy, and excess or direct cogeneration process heat. The proposed thermal energy storage along with the fossil fuel boiler will allow for the dual-purpose system to operate at steady-state by managing the dynamic variability of solar energy. Additionally, electric production is considered to supply a reverse osmosis plant (RO) without connecting to the local electric grid. A multi-period mixed integer nonlinear program (MINLP) is developed and applied to discretize operation period to track the diurnal fluctuations of solar energy. The solution of the optimization program determines the optimal mix of solar energy, thermal storage, and fossil fuel to attain the maximum annual profit of the entire system. A case study is solved for water treatment and energy management for Eagle Ford Basin in Texas.

By planting LEDs on the surfaces of orifice baffles, a novel batch oscillatory baffled photoreactor (OBPR) together with polymer-supported Rose Bengal (Ps-RB) beads are used to investigate reaction kinetics of a photo-oxidation reaction between α-terpinene and singlet oxygen (1O2). In the widely used NMR data analysis for this reaction, α-terpinene and ascaridole are treated as a reaction pair, assuming kinetically singlet oxygen is in excess or constant. We have, for the first time, examined the validity of the method, discovered that increasing α-terpinene initially leads to an increase of ascaridole, indicating that the supply of singlet oxygen is in excess. Applying kinetic analysis, a pseudo first order reaction kinetics is confirmed, supporting this assumption. We have subsequently initiated a methodology of estimating the 1O2 concentrations based on the proportionality of ascaridole concentrations with respect to its maximum under these conditions. With the help of the estimated singlet oxygen data, the efficiency of 1O2 utilization and the photo efficiency of converting molecular oxygen to 1O2 are further proposed and evaluated. We have also identified conditions where further increase of α-terpinene has caused decreases in ascaridole, implying kinetically that 1O2 has now become a limiting reagent, the method of treating α-terpinene and ascaridole as a reaction pair in the data analysis would no longer be valid under those conditions.

We experimentally investigate power-sensitive photo-thermal tuning (PTT) of two-dimensional (2D) graphene oxide (GO) films coated on integrated optical waveguides. We measure the light power thresholds for reversible and permanent GO reduction in silicon nitride (SiN) waveguides integrated with 1 and 2 layers of GO. Raman spectra at different positions of a hybrid waveguide with permanently reduced GO are characterized, verifying the inhomogeneous GO reduction along the direction of light propagation through the waveguide. The differences between the PTT induced by a continuous-wave laser and a pulsed laser are also compared, confirming that the PTT mainly depend on the average input power. These results reveal interesting features for 2D GO films coated on integrated optical waveguides, which are of fundamental importance for the control and engineering of GO’s properties in hybrid integrated photonic devices.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

By this contribution we would like to briefly highlight the problems in conceiving the “Hydrogen Bond” (HB) as a real short-range, directional, electrostatic, attractive interaction and to reframe its nature through the non-approximated view of condensed matter offered by a Quantum Electro-Dynamic (QED) perspective. We focus our attention on water, as the paramount case to show the effectiveness of this 40-years’ old theoretical background, which depicts water as a two-fluid system (where one of the two phases is coherent). The HB emerge to be the result of the electromagnetic field gradient in the coherent phase of water, whose vacuum level is lower than the non-coherent (gas-like) fraction. Thus, the HB can be properly looked at, i.e. no more as a “dipolar force” among molecules, but as the phenomenological effect of their collective thermodynamic tendency to occupy a lower ground-state, compatibly with temperature and pressure. This perspective allows to account for many “anomalous” behaviours of water and to understand why the calculated energy associated to HB should change when considering two molecules (water-dimer), or the liquid state, or the several kinds of ice. The emergence of a condensed, liquid, phase at room temperature is indeed the consequence of the boson condensation as described in the framework of spontaneous symmetry breakings (SSB). The switch from a still semi-classical Quantum Mechanical (QM) in the 1st quantization to a Quantum Field Theory (QFT) view embedded in the 2nd quantization is advocated for a more realistic and authentic description of water, condensed matter and living systems.

The heat generated during the startup process of dry gas seals, such as the friction heat of the asperities, viscous shear heat, and the expansion heat of the gas film, easily leads to seal failure and endangers the stable operation of turbomachinery. This study combines the statistically modified contact model and the average Reynolds equation by considering the adiabatic index and the microscale effects of dry gas seals to explore the heat generation characteristics of dry gas seals formed in series at multiple times. In particular, the change laws and influencing factors among the components, including the friction heat of asperities and the shear heat and expansion heat of the gas film and total heat, are investigated. A comparative analysis indicates that the slip flow effect increases the total heat during the startup process. The friction heat is much greater than expansion heat and shear heat. Despite constant acceleration, exponential acceleration, or Harrision acceleration, the heat changes are uneven during the startup process. In particular, the heat changes sharply in the early stage and gently in the later stage. The Harrision acceleration mode is the most conducive to sealing stability.

The objective of the prototype is to eliminate the polluting contamination of water sources, due to the leak of industrial waste without any kind of treatment, mainly generated by the industries and home sector. In this project, a prototype of water purification by plasma technology has been designed. The prototype will convert contaminated water into the plasma stream and eliminate the pathogens from the water by exposing it to ultraviolet radiation and plasma sterilisation. The polluted water will be accelerated at high speed using a water pump in order to convert it into a liquid-gas mixture for ease plasma generation. This process will be achieved when the electric supply from a source of alternating current (AC) is applied to the water by means of high voltage electrodes. After which, the mixture slows down to return into liquid form and the clean water is obtained. The whole process takes place without significantly raising the temperature also knows as non-thermal plasma. The device also has an automatic flow and pressure control system. Finally, a short feasibility study has been conducted on the water samples collected and report obtained from Chennai Metropolitan Water Supply and Sewage boards are reported. It has been concluded that this new plasma-based water treatment system will be more efficient and cheaper than the current wastewater treatment techniques and can be used in the future as the replacement of current secondary and tertiary treatments of industrial wastewater.

As one of the most promising ablative fillers, multi-walled carbon nanotubes (MWCNTs) have been used to improve the ablative resistance of Ethylene-Propylene-Diene Monomer (EPDM) insulators by facilitating the carbothermal reduction reaction of silica. However, the contribution of MWCNTs to char layer structure of the insulators was unclear. In this work, the effects of MWCNTs on char layer structure and ablative resistance were investigated in different EPDM-based insulators with and without silica. The results showed that adding only 3 phr MWCNTs can reduce the linear ablation rate of EPDM-based insulators without silica by 31.7%, while 6 phr MWCNTs are required to obtain similar results in EPDM-based insulators with silica. Both the char layer morphology of the two insulators gradually evolved into dense porous structure as MWCNTs content increasing, but their formation mechanisms are different. The XRD and Raman spectrum showed that different physicochemical reactions occurred around MWCNTs under different charring components. The proposed ablation mechanism was further verified by designing alternating multilayer distribution of MWCNTs and silica. This work can guide the construction of desirable char layer structure for increasing ablative resistance of EPDM-based insulators.

The research work explores the impact of temperature on Silicon photovoltaic (PV) panels considering Nigeria as case study. It is found that high solar radiation in Nigeria increases surface temperature of PV panel above 25oC of optimal operating temperature of PV panels. Redundant energy gain from incident solar energy is dissipated at the rear of PV panels as heat, which reduces the efficiency of PV panel. Cooling mechanism is needed to cool the PV panels to increase the efficiency. In this study we demonstrated a unique design of a bifunctional photovoltaic-thermal (PVT) system by employing heat exchanger at the rear of PV panel and water is used as a working fluid that is circulated through the heat exchanger to remove the excess heat. It is observed from the simulation results that Maiduguri peak annual electrical power output gives 1907kWh/kWp which is the highest, because of high solar radiation average of 727W/m2 in a year. And for Makurdi the peak annual electrical power output of 1542kWh/kWp while for Port Harcourt the peak power output of 1355kWh/kWp respectively. Interestingly, Polycrystalline Si-PV surface temperature decrease from 49.25oC to 38.38oC. Electrical power increased from 1526.83W to 1566.82W in a day and efficiency increase from 13.99% to 15.01%.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

Ultrafast chip nanocalorimetry opens up remarkable possibilities in materials science by allowing samples to be cooled and heated at extremely high rates. Due to heat transfer limitations, controlled ultrafast cooling and heating can only be achieved for tiny samples in calorimeters with a micron-thick membrane. Even if ultrafast heating can be controlled under quasi-adiabatic conditions, ultrafast controlled cooling can be performed if the calorimetric cell is located in a heat-conducting gas. It was found that the maximum possible cooling rate increases as 1/r0 with decreasing radius r0 of the hot zone of the membrane. The possibility of increasing the maximum cooling rate with decreasing r0 was successfully implemented in many experiments. In this regard, it is interesting to answer the question: what is the maximum possible cooling rate in such experiments if r0 tends to zero? Indeed, on submicron scales, the mean free path of gas molecules lmfp becomes comparable to r0, and the temperature jump that exists at the membrane/gas interface becomes significant. Considering the limitation associated with thermal resistance at the membrane/gas interface and considering the transfer of heat through the membrane, we show that the controlled cooling rate can reach billions of K/s, up to 1010 K/s.

Droughts occurring more and more frequently in recent years are usually associated with progressive climate changes. Modern monitoring methods is mainly associated with agricultural use due to the high market demand for services protecting against agricultural losses. In natural wetland ecosystem this problem is neglected which is probably due to fact that this are ecosystems rich in water by definition. Nevertheless this droughts might become a problem of wetlands, whose good condition depends on adequate hydration. Therefore this study focused on determination Crop Water Stress Index (CWSI) for natural heterogeneous wetland habitats. CWSI based on remotely sensed land surface temperature and associated basic meteorological (air temperature and humidity) measurements. CWSI was calculated based on high resolution LST measurements from UAV platform and compare with on ground measurements of soil moisture, CCI, fAPAR and meteorological conditions. Results shows that CWSI properly shows water condition of plants in measured habitats and revels high importance of metrological conditions during data acquisition.

Medical institutions, where several patients are treated and medical workers engaged, are always exposed to secondary viral and bacterial infections. It is critical to prevent infection transmission by indirect as well as direct contact through air or splash. The infections of most diseases can be transmitted through the air. HEPA filters installed in air conditioning equipment are used to prevent infection transmission through air in medical institutions, but air circulation takes a long time in a large space. Virus and bacteria smaller than 0.3 μm cannot be removed by the HEPA filter; hence, those microbes remain alive throughout the air ventilation. A plasma sterilizer has the capability to provide environmental friendly sterilization by employing reactive oxide species and reactive nitrogen species at a low cost. We developed an excellent plasma sterilizer by using a non-thermal atmospheric-pressure biocompatible plasma (NBP). Ozone concentration in plasma sources has been derived by Kuhn et al. [1]. The diffusion coefficients inside (D₀) and outside (D₁) the plasma sterilizer have been calculated to be 0.0641 m² s^-1 and 0.717 m² s^-1, respectively. To sustain high O₃ concentrations over 121 ppm inside the plasma source and low O₃ concentrations below 0.05 ppm outside the sterilizer, it is necessary to keep O₃ concentrations at the exit of plasma sterilizer below 0.28 ppm. so that diffusion coefficient D₁ has been designed to be as large as 11 times of D₀.

Nowadays, with smartphones people can easily take photos, post photos to any social networks and use the photos for some purposes. This leads to a social problem that unintended appearance in photos may threaten the privacy of photographed person. Some solutions to protect facial privacy in photos have already been proposed. However, most of them rely on different techniques to de-identify photos which can be done only by photographers, giving no choice to photographed person. To deal with that, we propose an approach that allows photographed person to proactively detect whether someone is intentionally/unintentionally trying to take pictures of him/her. Thereby, he/she can have appropriate reaction to protect the privacy. In this approach, we assume that the photographed person uses a wearable camera to record the surrounding environment in real-time. The skeleton information of likely photographers who are captured in the monitoring video is then extracted to be put into the calculation of dynamic programming score which is eventually compared with a threshold for recognition of photo-taking behavior. Experimental results demonstrate that by using the proposed approach, the photo-taking behavior is precisely recognized with high accuracy of 92.5%.

Instead of simplified steady-state models, with modern computers, one can solve the complete aero-thermodynamics happening in gas turbine engines. In the present article, we describe a mathematical model and numerical procedure to represent the transient response of a PT6A gas turbine engine operating at off-design conditions. The aero-thermal model consists of a set of algebraic and ordinary differential equations that arise from the application of the mass, linear momentum, angular momentum, and energy balances in each engine's component. The solution code has been developed in Matlab-Simulink using a block-oriented approach. Transient simulations of the PT6A engine start-up have been carried out by changing the original Jet-A1 fuel with biodiesel blends. Time plots of the main thermodynamic variables are shown, especially those regarding the structural integrity of the burner. Numerical results have been validated against reported experimental measurements and GasTurb simulations. The computer model has been capable to predict acceptable fuel blends, such that the real PT6A engine can be substituted to avoid the risk of damaging it.

The problem of water drinking supply is very important in the world, especially for developing countries, in particular Algeria. In this work we propose to study a distillation system based on solar energy process using an artificial intelligence approach in order to enhance the performance and the daily production. For this purpose, a conventional solar still and capillary film solar still was used. The operating parameters of the two distilleries are analyzed and the neural network approach was used to predict the performance through the amount of distillate, solar radiation and ambient temperature. The sensitivity between the operating parameters of the solar still for two case have been studied through the artificial neuron network model. The obtained results are promising, analyzed and discussed.

In this study, fibers were extracted from different parts of the okra plant (Abelmoschus esculentus) via water- and dew-retting methods. The fibers were subjected to physical and thermal analyses. The fibers obtained from the upper part of the okra plant show higher breaking strength and lower linear density. Fibers obtained via water-retting exhibited higher breaking strength, elongation at break rates, and lower linear density values. The paper also presents the results of thermogravimetric analysis of the okra fibers. Tests were carried out in oxygen and inert gas atmospheres. The temperature range of the main thermal decomposition stage was in the 275–400°C for range thermo-oxidation and 300–425°C for pyrolysis investigation. Slight differences were found in the thermal resistances of the tested fibers, which was confirmed by an analysis using the alpha s- alpha r methodology. The calculated activation energy values show a large-spread range.

Abstract: Currently, thermal power is the largest source of power in the world. Although the impacts of climate change on cooling water sufficiency in thermal power plants have been extensively assessed globally and regionally, their economic consequences have seldom been evaluated. In this study, the Asia-Pacific Integrated Model Computable General Equilibrium model (AIM/CGE) was used to evaluate the economic consequences of projected future cooling water insufficiency on a global basis, which was simulated using the H08 global hydrological model. This approach enabled us to investigate how the physical impacts of climate change on thermal power generation influence economic activities in regions and industrial sectors. To account for the uncertainty of climate change projections, five global climate models and two representative concentration pathways (RCPs 2.6 and 8.5) were used. The ensemble-mean results showed that the global gross domestic product (GDP) loss in 2070–2095 due to cooling water insufficiency in the thermal power sector was −0.21% (−0.12%) in RCP8.5 (RCP2.6). Among the five regions, the largest GDP loss of −0.57% (−0.27%) was observed in the Middle East and Africa. Medium-scale losses of −0.18% (−0.12%) and −0.14% (−0.12%) were found in OECD90 (the member countries of the Organization for Economic Co-operation and Development as of 1990) and Eastern Europe and the Former Soviet Union, respectively. The smallest losses of −0.05% (−0.06%) and −0.09% (−0.08%) were found in Latin America and Asia, respectively. The economic impact of cooling water insufficiency was non-negligible and should be considered as one of the threats induced by climate change.

With permafrost degenerating caused by climate change, water accumulation increases in permafrost regions during last decades. Water accumulation will deteriorate existing status of engineering in cold regions. Water accumulation can make a thermal effect on permafrost under construction, even result in failure of the subgrade. Moreover, the thermal effect is related to water temperature. However, temperature variation of water accumulation is complex, and its influence factors include air temperature, environment, scope of water accumulation and so on. In order to make analysis of the damage mechanism of water accumulation on permafrost, it is necessary to explore the internal temperature change of water accumulation. This paper proposes a review about temperature calculation method of water accumulation in cold environment. The thermal calculation method between air and water boundary of water accumulation is summarized. Water temperature change of water accumulation with various type is analyzed. The thermal calculation considering phase transformation in water accumulation is discussed, and heat transfer from the bottom of water accumulation to the underlying soil is further studied. Finally, the key factors which are advantageous to make research about the thermal effect of water accumulation in permafrost is proposed to optimize calculation method.

As a new kind of highly compact and efficient micro-channel heat exchanger, printed circuit heat exchanger (PCHE) is a promising candidate satisfying the heat exchange requirements of liquefied natural gas (LNG) vaporization at low and high pressure. The effects of airfoil fin arrangement on heat transfer an flow resistance were numerically investigated using supercritical liquefied natural gas (LNG) as a working fluid. The thermal properties of supercritical LNG were tested by utilizing a REFPROF software database. Numerical simulation was performed using FLUENT. The inlet temperature of supercritical LNG was 121 K,and its pressure was 10.5MPa. The reference mass flow rate of LNG was set 1.22 g/s for the vertical pitch L_v = 1.67 mm and the staggered pitch L_s = 0 mm, with the Reynolds number of about 3750. The SST k-ω model with enhanced wall treatment was selected by comparing with the experimental data. The airfoil fin PCHE had better thermal-hydraulic performance than that of the straight channel PCHE. Moreover, the airfoil fins with staggered arrangement displayed better thermal performance than that of the fins with parallel arrangement. The thermal-hydraulic performance of airfoil fin PCHE was improved with increasing L_s and L_v. Moreover, L_v affected on the Nusselt number and pressure drop of airfoil fin PCHE more obviously. In conclusion, a sparser staggered arrangement of fins showed a better thermal-hydraulic performance in airfoil fin PCHE.

Thermal-expandable microcapsules (TEMs) for water-based coatings were synthesized with co-polymer of Acrylonitrile (AN) - Methyl methacrylate (MMA) - Ethylhexyl acrylate (EHA) - Divinylbenzene (DVB) as shell and toluene-p-sulfonyl hydrazide as core by suspension polymerization method. It was found that the microcapsules with desirable thermal expansion property and good heat stability could be obtained with a shell monomers composition of 70% AN /20% MMA /9% EHA /1% DVB. When 2% styrene-maleic acid copolymer (SMC) as emulsifier and 3% poly (vinyl pyrrolidone) (PVP) as dispersing agent were used, well defined spherical and more uniform microcapsules could be prepared. It was also found that when the shell/core mass ratio was 3:1, an encapsulation efficiency of ca. 94.5% could be achieved. Beyond this ratio, the increase of encapsulation efficiency reached a plateau. The 100 μm thickness film of water-based coating containing 5% microcapsules could be expanded to the thickness of 450 μm after exposed at 150 °C for 2 minutes. TG analysis revealed the mass loss start temperature of coating increased by more than 30 °C when 5% microcapsules were added to water-based coatings, which demonstrated the flame-retardant function of the coatings.

The research carried out concerned the laboratory assessment of the applicability of the Crop Water Stress Index (CWSI) as a practical tool for assessing the risk of desiccation for selected wetland habitats: transition mires and quaking bogs as well as alkaline fens. The analysis was carried out on 3 soil samples with a vegetation cover (with the dimensions of 40×40×30 cm) collected during the full vegetation season for each mentioned habitat, with a characteristic species composition. Experimental research was carried out between 17^th May 2018 and 19^th June 2018. Thermal, RGB and multispectral images, chlorophyll content, volumetric soil moisture, air temperature and relative humidity measurements were taken for each sample every two days. The obtained results clearly indicate the dependence between CWSI and plant condition parameters in the first phase of desiccation. At the same time, as a result of the observations taken, thresholds have been set, indicating different desiccation phases.

The purpose of this paper is to describe a new way of producing renewable energy based on fjords as a water heater. We will call this system the Water-thermal Energy Production System (WEPS), because the basic idea is to extract heating and cooling energy from water. Although a prototype of WEPS has existed in Norway for more than ten years, a WEPS currently in operation has not been financially analyzed in the literature. Coastal parts of Norway have a potential of 5 TWh of profitable WEPS-facilities [9], due to convenient access to fjords containing water with stable all-season temperatures of about 4–12C when the depth of the water is about 50 meters. This stability of the water temperature makes it possible to extract energy from the fjord in a very efficient way. The potential for economically-profitable WEPS in other parts of the world has not been estimated. In order to answer such a question, more research is required. We have conducted a case study of a WEPS located in the Norwegian municipality of Eid. This is the first full-scale Norwegian WEPS, and it has been operating since 2006. The nascent years have passed, and the technology has been in operation for some years. In this paper, we have made an estimate of the business profitability and the external effects based on past empirical evidence and some assumptions about future development in some key figures. The results suggests that WEPS-Eid has been a profitable investment carrying a positive internal rate of revenue, even if the present underutilization in production capacity will continue in the future. Stability in energy prices for heating purposes has also gained customers compared to the more volatile prices of alternative renewable energy, like hydropower or wind turbines. The negative, external effects in the operating phase from WEPS-Eid are insignificant. Despite the significant profitability of the WEPS facility in Eid, there are two main obstacles for new entrants. There is a lack of relevant operational information for potential investors due to few facilities. This leads to uncertainty, and investments in WEPS appear as a risky business. Secondly, construction of a WEPS requires both big financial investments in digging and facilitating long trenches for a pipeline system and time and effort spent on acquiring the licenses needed for doing this work. A coordinating unit is probably required in order to get the necessary public and private licenses and to reduce fixed costs by coordinating other tasks in the same trenches, like pipes for water and sewer, fiber cables and tele-cables. In Eid, the local municipal administration was the coordinating unit.

Laboratory experiments and investigations into natural phenomena in this research series have unveiled the presence of a gravitational repulsion force that permeates our environment on both microscopic and macroscopic scales, contingent upon the thermal energy present. This paper presents a study exploring novel properties of gravitational forces among gas molecules, employing principles of thermodynamics. A model has been devised based on the interactions between pairs of gas molecules. While traditional models treat gravitational interaction as a singular force, our experimental approach validates it as the composite of two distinct forces: gravitational repulsion and attraction. By utilizing established experimental data on gas thermodynamics, our model demonstrates robust performance both analytically and experimentally. It verifies the coexistence of gravitational repulsion and attraction forces among gas molecules, showcases their Inverse-Cube relationship with distance, and elucidates the direct proportionality of the repulsion force to absolute temperature. This bridges a crucial gap between energy and fundamental forces. The order of magnitudes of gravitational repulsion and attraction forces are found to be considerably large, contrasting with the low values predicted by classical theory, which results from their amalgamation. Recognizing these forces as substantial in magnitude promises unprecedented outcomes and advancements.

This study evaluates the production of biohydrogen from agro industrial waste. The worldwide energy demand is increasing exponentially and the reserves of fossil fuels are depleting, the combustion of fossil fuels has the effect on environment because of CO2 emission. Hydrogen generation market size is forecast to cross 180 billion by 2024, according to a new research report by global market. For the production of biohydrogen. we had chosen groundnut shell as our source, using Tween80 as a surfactant we had undergone pre-treatment studies for (10min,20min,30min,40min,50min) we had estimated the content of cellulose, protein, carbohydrates at (1%,2%,3%,4%,5%) and obtained the optimum value in the form of graph. The production of hydrogen is done by using the rumen fluid of the cow and the quantity of the hydrogen produced by this process is identified by using the analytical instrument Gas Chromatography.

Bio-devices are designed to allow biological matter to perform in vitro almost the same functions it performs in vivo. Therefore, they can benefit from the specificities of such materials and are expected to perform better than traditional devices. On the other hand, the integration of biological material with electronic/electrochemical instrumentation requires careful attention and can produce unconventional results. In this paper, we describe the impedance response of an electrochemical cell that converts sunlight into electrical power. It uses the photosynthetic system known as Reaction Center, which is the core of photosynthesis in several living beings. Under illumination, an abrupt transformation drives the cell electrical response from insulator to conductor and a photocurrent is observed. The impedance spectrum shows a peculiar shape which significantly modifies with the protein activation. It has been analyzed by means of a graphical/analytical/ numerical procedure. The modelling identifies an analogue electrical circuit, whose parameters give quantitative information about the underlying process. Finally, an appropriate normalization of data is proposed which validates data in dark and light and can be useful as a fast screening of measurements.

Since a large amount of sewage sludge (WSS) has been generated daily, it is necessary to explore effective methods for utilizing WSS. Although a photo-fermentation system sometimes alters the characteristics of microbial functions, there are no attempts to perform the photo-fermentation using WSS which is regularly treated under a dark-fermentation style. In this study, the effect of photo-fermentation (photo-irradiation) on anaerobic digestion using WSS was revealed. Photo-irradiation during the anaerobic digestion of WSS significantly reduced the amount of organic acids and hydrogen sulfide and methane production was also suppressed. However, it was shown that the activity of sulfate-reducing bacteria in WSS under the light treatment increased. Photo-irradiation also stimulated the growth of green-sulfur bacteria and induced anoxygenic photosynthesis, by which the fermented samples turned green linking with the consumption of hydrogen sulfide. Finally, a dark/light switching fermentation was able to reduce only hydrogen sulfide while methane production remained the same.

Compact solar-powered plasma water generator: enhanced on-site aged seed germination with the corona dielectric barrier discharger

Every simplification has the potential to add a systematic error to the measured value. Sometimes, the addition does not render the measurement useless. In the case of oil well flow measurements based on the thermal properties of the fluid in the well, the addition of a systematic error of up to 20% can occur if the variation in the internal energy of the fluid and, most importantly, the transient nature of heat transfer in the completion are not taken into account. This error is a mathematical consequence of the simplifications chosen. To work within the first hours of good operation, given the need for immediate application in a prototype water injection well developed and installed at the UFRN, this article presents an analytical solution for calculating the flow rate by solving the differential equations obtained by applying the principles of mass and heat transfer. As a result, at the cost of greater complexity, the systematic error drops to values of less than 1% in the first two hours of operation of the well, as seen throughout this document.

We present the results on photothermal (PT) and heat conductive properties of nanogranular silicon (Si) films synthesized by evaporation of colloidal droplets (drop-casting) of 100 ± 50 nm sized crystalline Si nanoparticles (NP) deposited on glass substrates. Finite difference time domain (FDTD) and finite element mesh (FEM) modeling of absorbed light intensity and photo-induced spatial temperature distribution across the Si NP films were well correlated with the local temperatures measured by micro-Raman spectroscopy and used for determination of heat conductivities in the films of various thicknesses. Cubic-to-hexagonal phase transition in these films caused by laser heating was found to be heavily influenced by the film thickness and heat conductive properties of glass substrate, on which the films were deposited. Heat conductivities across the drop-casted Si nanogranular films were found to be in the range of lowest heat conductivities of other types of nanostructurely voided Si films due to enhanced phonon scattering across inherently voided topology, weak NP-NP and NP-substrate interface bonding within nanogranular Si films.

This article provides insight into flow measurement techniques in water injection wells in oil production fields, with a particular focus on the initial phases of operation. Consequently, the method created by Ramey in 1962, originally intended for estimating the temperature of the injection fluid, has been adapted to calculate the flow rate. In this technique, the calculation This procedure is based on the correlation between the thermal flux formed in the well. The discrepancy between the temperatures of the injected liquid and the geothermal temperature of the reservoir is the main source of the systematic errors in Ramey’s technique. To a lesser extent, but still significant, failure to observe the injection time in a fluid variation also results in an error problem that needs the failure to adhere to the scheduled injection time for a fluid alteration also yields a notable error dilemma that needs to be fixed. The reduction of listed systematic errors is the product of the main part of this article.

In recent years, the genesis of natural gas and the definition of major gas source rocks in the Baiyun Sag of the Pearl River Mouth Basin have attracted extensive attention from scholars. There is still considerable controversy over the genesis and the main gas source rocks of natural gas. In this study, the chemical kinetics method of natural gas generation and carbon isotope fractionation was used to study the generation history and isotope evolution history of Paleogene natural gas in the Y5 well area located on the north slope of Baiyun Sag. And other geochemical discriminant methods were applied simultaneously to determine the type and source rocks of natural gas. The results show that the natural gas in the Y5 well area on the northern slope of Baiyun Sag is mainly kerogen degradation gas, mixed with a small amount of oil cracking gas. The mixture of kerogen degradation gas and a small amount of crude oil cracking gas caused the inversion of the carbon isotope sequence of ethane and propane. The natural gas in the Y5 well area mainly comes from delta–shallow lacustrine facies source rock. The high–quality reservoirs in the shallower strata accumulate natural gas generated in the early stage, and the tight reservoirs in the deeper strata mainly accumulate natural gas generated in the late stage.

This work aims to investigate the effect of catalyst content and reaction time by catalytic upgrading from pyrolysis vapors of residual fat at 450 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, refractive index, and acid value) and chemical composition of organic liquid products (OLP), over a catalyst fixed bed reactor, in semi pilot scale. Pellets of Red Mud chemically activated with 1.0 M HCl were used as catalysts. The experiments were carried out at 450 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) Red Mud pellets activated with 1.0 M HCl, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 40, 50, 60, 70 and 80 min in order to analyze the process kinetics. The physicochemical properties (density, kinematic viscosity, acid value, and refractive index) of OLP were determined by official methods. The chemical functions present in OLP determined by FT-IR and the chemical composition by GC-MS. The thermal catalytic cracking of residual fat show OLP yields from 54.4 to 84.88 (wt.%), aqueous phase yields between 2.21 and 2.80 (wt.%), solid phase yields (coke) between 1.30 and 8.60 (wt.%), and gas yields from 11.61 to 34.22 (wt.%). The yields of OLP increases with increasing catalyst content while those of aqueous, gaseous and solid phase decreases. For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of OLP decreases with increasing reaction time. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the thermal and thermal catalytic cracking experiments, the hydrocarbon content within OLP increases with reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties (density, kinematic viscosity, and acid value) and the maximum hydrocarbon content of OLP were obtained at 450 °C and 1.0 atmosphere, using a catalyst fixed bed reactor, with 5.0% (wt.) Red Mud pellets activated with 1.0 M HCl as catalyst.

Almost all single-family detached house in Canada consume huge electricity for space heating and domestic hot water (DHW) purposes. There are many possibilities to design an energy-efficient house. A solar water heating system can be used for domestic water and space heating. Water temperature can be kept constant always by connecting a heat pump or oil burner because solar energy is intermittent. Proper and optimized solar photovoltaic and collector design, tank design, heat pump selection, house insulation, total demand calculation in each section are essential. Energy-Efficient house design has been proposed with water heating and space heating system and compared with the existing system, solar PV based systems, and solar collector based system. The tracking and non-tracking based solar thermal collector based and the solar photovoltaic based system has been compared in this paper and investigate the suitable one for practically applicable and acceptable by the people. Simulation has been done by using the PolySun software. It found that by implementing the proposed PV based system with tracking is highly suitable considering lower cost, high output power, flexibility, easy installation.

The fabrication and characterisation of photo-anodes based on black-Si (b-Si) are presented using a photo-electrochemical cell in NaOH solution. Black-Si was fabricated by maskless dry plasma etching and was conformally coated by tens-of-nm of TiO2 using atomic layer deposition (ALD) with a top layer of CoO_x cocatalyst deposited by pulsed laser deposition (PLD). Low reflectivity R < % of Black-Si over the entire visible and near-IR (λ < 2 µm) spectral range is favourable in better absorption of light while an increased surface area facilities larger current densities. Photoelectrochemical performance of the heterostructured photoanode is discussed in terms of n-n junction between b-Si and TiO₂.

In this paper, first the Self-Written Waveguide (SWW) process in wet photopolymer media (liquid solutions), are examined for three examples: single-, counter-, and co-fibers exposure. Then the SWWs formed inside solid material are examined including the effects of manipulating the alignment of the fibers. In all cases high precision measurements are used to position the fiber optic cables (FOCs) before exposure using a microscope. The self-writing process is indirectly monitored by observing (imaging) the light emerging from the side of the material sample during SWW formation. In this way the optical waveguide trajectories formed in an Acrylamide/Polyvinyl Alcohol (AA/PVA) a photopolymer material (sensitized at 532 nm) are examined. First the transmission of light by this material is characterized. Then the bending and merging of the waveguides which occur are investigated. The predictions of our model are shown to qualitatively agree with the observed trajectories. The largest index changes taking place at any time during the exposure, i.e. during SWW formation, are shown to take place at the positions where the largest exposure light intensity is present. Typically, such maxima exist close to the input face and the first maximum is referred to as the location of the Primary Eye. Other local maxima also appear further along the SWW and are referred to as Secondary Eyes, i.e. deeper within the material.

Groundwater contamination by nitrate and organic chemicals (e.g. 1,4-dioxane) is a growing worldwide concern. This work presents a new approach for simultaneously treating nitrate and 1,4-dioxane, which is based on UV sensitization of nitrate and sulfite, and the production of reactive species. Specifically, water contaminated with nitrate and 1,4-dioxane is irradiated by a UV source (< 250 nm) at relatively high doses, to sensitize in-situ nitrate and generate HO•. This leads to the oxidation of 1,4-dioxane (and other organics), and the (undesired) production of nitrite as an intermediate. Subsequently, sulfite is added at an optimized time-point, and its UV sensitization produces hydrated electrons which reacts and reduces nitrite. Our results confirmed the effectivity of the proposed treatment: UV irradiation of nitrate (at > 5 mg N/L) efficiently degraded 1,4-dioxane, while producing nitrite at levels higher than 1 mg N/L (its MCL in drinking water). Adding sulfite to the process after 10 minutes of irradiation reduced the concentration of nitrite, without affecting the degradation rate of 1,4-dioxane. The treated water contained elevated levels of sulfate; albeit at much lower concentration than its MCL. Treating water contaminated with nitrate and organic chemicals (often detected concomitantly) typically requires several (expensive) treatment processes. The proposed approach may present a cost-effective alternative, employing a single system for the treatment of nitrate and organic contaminants

In a world where conventional sources of energy are fast depleting, the quest for alternative energy sources may hold the key for the survival of humanity. In the present work, emphasis has been given to the idea of producing energy from perovskite based solar cells. In order to bring this idea into fruition, a unique and novel nano structured perovskite material n-propyl ammonium lead chloride (C₃H₇NH₃⁺PbCl₃⁻) was prepared through a unique co-precipitation route using n-propyl amine (n-C₃H₇NH₂) and hydrochloric acid as the starting precursors with aqueous solution of Pb(CH₃COO)₂3H₂O. Finally acetic acid was added to the solution and this solution was allowed to concentrate and then gradually cooled down to room temperature. After math, the synthesized material was spin-coated on TiO₂ film to fabricate the solar cell. The device was then undergone systematic analysis using XRD, SEM, UV and Photo Conversion to get a transparent idea regarding its structural, electrical and optical properties. When experimentally applied, this perovskite-based solar cell has shown energy conversion efficiency (η) of around 6.01 % which is noticeably good. Thus it can be concluded that this material is promising for fabrication of vastly efficient solar cells. This technology can be tried in large scale as an alternative of conventional energy in the near future.

Inverse gas chromatography at infinite dilution was used to determine the surface thermodynamic properties of silica particles and PMMA adsorbed on silica, and more particularly, to quantify the London dispersive energy γsd, the Lewis acid γs+ and base γs- polar surface energies of PMMA/silica composites as a function of the temperature and the recovery fraction θ of PMMA. The polar acid–base surface energy γsAB and the total surface energy of the different composites were then deduced as a function of the temperature. In this paper, the Hamieh thermal model was used to quantify the surface thermodynamic energy of poly methyl methacrylate (PMMA) adsorbed on silica particles at different recovery fractions. A comparison of the new results was carried out with those obtained by applying other molecular models of the surface areas of organic molecules adsorbed on the different solid substrates. An important deviation of these molecular models from the thermal model was proved. The determination of γsd, γs+, γs-, and γsAB of PMMA in both bulk and adsorbed phases showed an important non-linearity variation of these surface parameters as a function of the temperature. The presence of maxima in the curves of γsd(T) highlighted the second order transition temperatures in PMMA showing beta-relaxation, glass transition and liquid-liquid temperatures. These three transition temperatures depended on the adsorption rate of PMMA on silica. The proposed method gave a new relation between the recovery fraction of PMMA and its London dispersive energy showing an important effect of the temperature on the surface energy parameters of adsorption of PMMA on silica. A universal equation relating γsd(T,θ) of the systems PMMA/silica to the recovery fraction and the temperature was proposed.

The physicalchemistry properties and crystal structure of were nano-ZrO₂+3mol.%Y₂O₃ determined. The kinetics of the formation of H₂ as a result of the decomposition of H₂O on the surface of nano-ZrO₂+3mol.%Y₂O₃ was studied. Effects of adsorption and desorption process on ZrO₂+3 mol.%Y₂O₃ nanoparticles were studied at different (T=400÷1000⁰C) temperature. The study of H₂ in thermal processes at nano-ZrO₂+3 mol.%Y₂O₃ system increased. Such an increase in H₂ generation in comparison with a pure H₂O as thermal processes had formedactive centers for H₂O decomposition on the surface of the catalyst at the expense of δ-electrons emitted on the surface of nano-ZrO₂+3 mol.%Y₂O₃. This showed that the dimensions of the studied nanoscale particles systems are comparable to the free running distance of energy carriers generated by of nano-ZrO₂+3 mol.%Y₂O₃ as a result of thermal processes. These results are promising for hydrogen generation by waer spliting in near future.

The multitarget therapeutic strategy, as opposed to the more traditional ‘one disease-one tar-get-one drug’, may hold promise in treating multifactorial neurodegenerative syndromes, such as Alzheimer’s disease (AD) and related dementias. Recently, combining a photopharmacology approach with the multitarget-directed ligand (MTDL) design strategy, we disclosed a novel donepezil-like compound, namely 2-(4-((diethylamino)methyl)benzylidene)-5-methoxy- 2,3-dihydro-1H-inden-1-one (1a), which in the E diastereomeric form (and about tenfold less in the UV-B photo-induced isomer Z) showed the best activity as dual inhibitor of the AD-related targets acetylcholinesterase (AChE) and monoamine oxidase B (MAO-B). Herein, we investigated further photoisomerizable 2-benzylideneindan-1-one analogs 1b-h with the unconjugated tertiary amino moiety bearing alkyls of different bulkiness and lipophilicity. For each compound the thermal stable E diastereoisomer, along with the E/Z mixture as produced by UV-B light irradia-tion in the photostationary state (PSS, 75% Z), was investigated for the inhibition of human ChEs and MAOs. The pure E-diastereoisomer of the N-benzyl(ethyl)amino analog 1h achieved low nanomolar AChE and high nanomolar MAO-B inhibition potencies (IC50s 39 and 355 nM, re-spectively), whereas photoisomerization to the Z isomer (75% Z in the PSS mixture) resulted in a decrease (about 30%) of AChE inhibitory potency, and not in the MAO-B one. Molecular docking studies were performed to rationalize the different E/Z diastereoselectivity of 1h toward the two target enzymes.

Bioelectrocatalysis has become one of important research fields in electrochemistry and provided a firm base for an important technology for application to various bioelectrochemical devices such as biosensors, biofuel cells, and biosupercapacitors. The understanding and technology in bioelectrocatalysis have been greatly improved by introducing nanostructured electrode materials and protein-engineering methods over the last few decades. Recently, the electro-enzymatic production of renewable energy resources and useful organic compounds (bioelectrosynthesis) also attracts worldwide attention. In this review, we summarize recent progress in applications of enzymatic bioelectrocatalysis.

The chlorophyll is one of the most important natural pigments used extensively in the food industry. Two important factors for the production of chlorophyll are the use of plants rich in chlorophyll and efficiency of extraction method. Present investigation was performed to compare the extraction of photosynthetic pigments by using solvents of different chemical nature. The purslane plants with different growth behavior viz. Scrollable and standing were grown under shade and sunshine stress condition. Different solvents including diethyl ether, 5% ethanol, pure acetone, 20% acetone, pure methanol and 10% methanol were used to extract chlorophyll and carotenoids from the purslane plant. The results indicated that stress, growth type and different solvents had a significant effect on the extraction of chlorophyll and carotenoids. Different trend was observed in extraction rate for chlorophylls and carotenoids. Among the solvents, pure methanol was the best for extraction of chl a. Methanol and acetone were appropriate solvents to achieve the highest amount of chlorophyll from plant tissues. Among different solvents, pure methanol for chl a, pure acetone and methanol for carotenoids were best solvent for purslane plant with a growing type scrollable of under shade.

Ultralong carbon nanotubes (UCNTs) are highly demanded for nanocomposites applications because of their magnificent physical and chemical properties. UCNTs are synthesized by catalytic chemical vapor deposition (CCVD) method and, before using as fillers in nanocomposites, should be purified from residual catalyst and non-CNT particles without significant destruction or scissoring of UCNTs. The role of water vapor for purification of UCNTs is investigated, the importance of water assistance in this process is confirmed. It was shown that wet air treatment of products of UCNTs CCVD synthesis under mild conditions can be used to decrease sufficiently residual catalyst content without significant carbon losses in comparison with the results obtained with dry air, while the residual iron content was shown to influence heavily on the subsequent oxidation of different forms of carbons, including UCNTs. The increasing of D/G ratio of Raman spectra after wet air treatment of products of UCNTs CCVD synthesis makes it possible to conclude that iron catalyst particles transform into iron oxides and hydroxides that caused inner structural strains and destruction of carbon shells improving removal of the catalyst particles by subsequent acid treatment. UCNTs purification with water assistance can be used to develop economically and ecologically friendly methods for obtaining fillers for nanocomposites of different applications.

This research is a preliminary phase of a general effort to develop a generic-data transferring capability via human haptic thermal sensation (generic-data refers to a coded language like Morse or Braille). For the capability to be effective, it must include a large variety of short recognizable cues. Hence, we propose the concept of cues based on sequences of thermal pulses, i.e., combinations of warm and cool pulses with several levels of intensity. The objective of this study was to determine the feasibility of basing a generic-data-transfer capability on thermal cues composed of sequences of short pulses. The research included defining the basic characteristics of the stimuli parameters and developing practical methods for generating and measuring them. Several sequences were designed in light of the relevant data known to date, and tests were conducted. The thermal cues presented to the participants were sensed and recognized by touch. The results indicate high feasibility for a capability that is applicable in various scenarios. In addition, the low impact on human skin temperature due to short stimuli duration represents an inherent advantage for later implementation. This report presents promising findings and offers insights for further investigation.

This paper constitutes an original and new methodology for the determination of the surface properties of carbon fibers in the two oxidized and untreated forms by inverse gas chromatography technique at infinite dilution based on the effect of the temperature on the surface area of the various organic molecules adsorbed on the carbon fibers. The studied thermal effect proved a large deviation of the classical methods or models relative to the new determination of the surface properties of carbon fibers, such as the dispersive component of their surface energy, the free surface energy, the free specific energy, the enthalpy and entropy of adsorption of molecules on the carbon fibers. The obtained specific enthalpy and entropy of adsorption for the polar solvents led to the determination of the Lewis’s acid-base constants of carbon fibers. Different molecular models and chromatographic methods were used to quantify the surface thermodynamic properties of carbon fibers and compared to the thermal model. The obtained results proved that the oxidized carbon fibers gave more specific interaction energy and greater acid-base constants than that of the untreated carbon fibers and thus highlighting the important role of the oxidization on the acid-base of fibers. The determination of the specific acid-base surface energy of the two carbon fibers showed greater values of the oxidized carbon fibers relative to the untreated carbon fibers. An important basic character was highlighted for the two studied carbon fibers, larger than the acidic character. It was observed that the Lewis’s acid-base constants of the oxidized carbon fibers are larger than that of the untreated fibers with more accentuated basic charterer. This result was confirmed by all molecular models and chromatographic methods.

Applied electrostatic engineering can be used to construct greenhouses that prevent entry of insect pests. Two types of electric field screen were used to exclude pests from the greenhouse: single- and double-charged dipolar electric field screens (S- and D-screen, respectively). The S-screen consisted of iron insulated conductor wires (ICWs) arrayed in parallel (ICW-layer), a grounded metal net on either side of the ICW-layer, and a direct current voltage generator. S-screens were attached to the side windows of the greenhouse to repel whiteflies (Bemisia tabaci) that approached the nets. The D-screen was installed in a small anteroom at the greenhouse entrance to capture whiteflies entering through it. The ICW-layers of the D-screen were oppositely charged with equal voltages and arrayed alternately, and an insulator board or grounded metal net was placed on one side of the ICW-layer. The ICW-layers captured whiteflies entering the electric field of the double-charged dipolar electric field. Three screens equipped with yellow or gray boards or a grounded metal net were installed in the anteroom based on the airflow inside the room, as most whiteflies were brought in by air when the door was opened. Two D-screens with boards were useful for directing the airflow toward the wall with the netted D-screen. This screen eliminated the insects and the pest-free air was circulated inside the greenhouse. The D-screen with the yellow board attracted the whiteflies and was effective for trapping them when there was no wind. Our method kept the greenhouse pest-free throughout the entire period of tomato (Solanum lycopersicum) cultivation.

In this work, the solar light-induced redox photoactivity of the ZnO semiconductor material was used to prepare at room temperature CuxO-ZnO composite catalysts with a control of the chemical state of the copper oxide phase. The preparation of Cu2(I)O-ZnO and Cu(II)O-ZnO composite catalysts was achieved by using Cu(acac)2 in THF-water and Cu(NO3)2 in water as metallic precursor, respectively. Prior to the implementation of the photo-assisted synthesis method, the most efficient photoactive ZnO material was selected among different ZnO materials prepared by the low temperature polyol method and through the precipitation method with carbonates and carbamates as precipitation agent, by taking the photocatalytic degradation of the 4-chlorophenol compound in water under simulated solar light as model reaction. The ZnO support materials were characterized by XRD, BET, TGA, SEM and TEM, and the synthesis method was strongly influencing their photoactivity in terms of 4-chlorophenol degradation and of total organic carbon removal. The most photoactive ZnO material was prepared by precipitation with carbonates and calcined at 300°C, and was taking advantage of a high specific surface area and a small mean crystallite size for achieving a complete 4-chlorophenol mineralization within 70 min of reaction, with a minimum Zn2+ released to the solution due to surface photocorrosion. Beside thermal catalysis applications, this work opened a new route for the facile synthesis of Cu2O-ZnO heterojunction photocatalysts, that could take advantage under solar light of the heterojunction built between the p-type semi-conductor Cu2O with direct visible light band gap and the ZnO semiconductor phase.

Ultra-large cold-water pipes (CWP) may present structural instability phenomenon under complex and variable operating conditions, and the current theoretical analysis rarely takes into account the influence of multiple key parameters at the same time, resulting in some errors between the prediction results and the actual deformation behavior of the pipe. Considering this issue, this paper establishes a computational analysis model of the mechanical performance of the CWP based on the Euler-Bernoulli beam theory, considering the effect of waves, the clump weight at the bottom, internal flow and sea current, and gives a time-dependent solution of the mechanical response of the pipe with the action of multiple key parameters using the differential quadrature method (DQM). Additionally, the correctness and validity of the theoretical model are well verified by comparing the numerical solution with the theoretical results. Finally, to study the effects of operating conditions on the mechanical response of the pipe, the effects of waves, the clump weight, internal flow and sea current on the lateral deflection and maximum bending moment of the pipeline are discussed based on numerical simulation and orthogonal experimental method. The results show that changing the wave strength and internal flow velocity has little effect on the lateral deflection of the CWP, and the clump weight at the bottom can effectively suppress the lateral deflection of the pipeline, but increasing the current velocity can significantly increase the lateral deflection of the pipeline, which can lead to the instability of the pipe. Nevertheless, the effects of waves, the clump weight, internal flow and sea current on the maximum bending moment of the pipeline are basically the same, all of them increase sharply at first, and then decrease gradually until they level off, and the differences in the effects are mainly reflected in the different locations of the pipe sections. This paper suggests the design guidance of CWP in aspect of dynamic response depending on the operating condition.

Low-cost miniature hyperspectral and thermal cameras onboard lightweight unmanned aerial vehicles (UAV) bring new opportunities for monitoring land surface variables at unprecedented fine spatial resolution with acceptable accuracy. This research applies hyperspectral and thermal imagery from a drone to quantify upland rice growth and water use efficiency (WUE) after biochar application in a Costa Rican dry region. The field flights were conducted over two experimental groups with bamboo biochar and sugarcane biochar amendments and one control group without biochar application. Rice canopy biophysical variables were estimated by inversion of a canopy radiative transfer model on hyperspectral reflectance. Variations in gross primary production (GPP) and WUE across treatments were estimated from the normalized difference vegetation index (NDVI), canopy chlorophyll content (CCC), and evapotranspiration. We found that GPP was increased by 41.9±3.4 % when using bamboo biochar and 17.5±3.4 % when using sugarcane biochar, which was probably due to higher soil moisture in the biochar-amended plots and led to significantly higher WUE by 40.8±3.5 % in bamboo biochar and 13.4±3.5 % in sugarcane biochar. This study demonstrated the use of hyperspectral and thermal imagery from drone to provide indicators for quantifying biochar effects on tropical dry cropland by integrating with ground point samples and physical models.

This paper reports the overall thermal performance of a cylindrical parabolic concentrating solar water heater (CPCSWH) with inserting nail type twisted tape (NTT) in the copper absorber tube for the nail twist pitch ratios 4.787, 6.914 and 9.042 respectively. The experiments are conducted for a constant volumetric water flow rate and during the time period 9:00 h to 15:00 h. The useful heat gain, hourly solar energy collected and hourly solar energy stored of this solar water heater are found higher for nail twist pitch ratio 4.787. The above said parameters are found to be a peak at noon and observed to follow the path of variation of solar intensity. At the starting of the experiment, the value of charging efficiency is observed to be maximum. Whereas the maximum value of instantaneous efficiency and overall thermal efficiency are observed at noon. The key finding is that the nail twist pitch ratio enhances the overall thermal performance of the CPCSWH.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

The quartz tuning fork used as an acoustic sensor in Quartz-Enhanced Photo-Acoustic Spectroscopy gas detection systems is usually read-out by means of a transimpedance preamplifier, based on a low-noise operational amplifier closed in a feedback loop. The gain-bandwidth product of the operational amplifier used in the circuit is a key parameter which must be properly chosen to guarantee that the circuit works as expected. Here we demonstrate that, if the value of this parameter is not sufficiently large, the response of the preamplifier exhibits a peak at a frequency which does not coincide with the series resonant frequency of the quartz tuning fork. If this peak frequency is selected for modulating the laser bias current and is also used as reference frequency of the lock-in amplifier, a penalty results in terms of signal to noise ratio at the output of the QEPAS sensor. This worsens the performance of the gas sensing system in terms of ultimate detection limits. We show that this happens when the front-end preamplifier of the quartz tuning fork is based on some amplifier models that are typically used for such application, both when the integration time of the lock-in amplifier filter is long, to boost noise rejection, and when it is short, in order to comply with a relevant measurement rate.

Following the occurrence of a typhoon, quick damage assessment related to residents can facilitate quick dispatch of house repair and disaster insurance works. Employing a deep learning method, this study used aerial photos of the Chiba prefecture obtained following the Typhoon Faxai in 2019 to automatically detect and evaluate the roof damage. This study comprised three parts: training deep learning model, detecting the roof damage using trained model, and classifying the level of roof damage. The detection object comprised roof outline, blue tarps, and roof completely destroyed. The roofs were divided into three categories: roof without damage, roof with blue tarps and roof completely destroyed. the F value obtained using the proposed method was higher than those obtained using other methods. In addition, it can be further divided into 5 levels from level 0 to 4. Finally, the spatial distribution of the roof damage was analyzed using ArcGIS tools. The proposed method is expected to provide certain reference for the real-time detection of the roof damage after the occurrence of a typhoon.

This article presents, for the first time, the kinetics and the general conversion features of free radical polymerization (FRP) in a 3-component system (A/B/N), with [A] being the initiator, and [B] and [N] are additives, based on the proposed mechanism of Rahal et al. Higher FRP can be achieved by additives [B] and [N], via the dual function of (i) regeneration [A], and (ii) generation of extra radicals (R) via the radicals (S' and S) produced by N.The initiator (coumarin) shows a dual photo-oxidation and photo-reduction character for high efficacy. The FRP conversion efficacy (CE) depends not only on the property of the initiator [A], the additives [B] and [N}, but also the types of monomers. For example, when [A]=CoumC, [A]/NPG is more efficient than [A]/Iod, but revserse trend occurs in some monomers. However, 2-component systems (with CE=0% to 80%) are always less efficient than that of 3-component systems (with CE=70% to 86%, in TMPTA). Specific systems with [A]=coumarins, [B]=Iodonium salt, and N=NPG are analyzed. Analytical formulas for the role of each component concentration, light intensity and coupling rates on the conversion efficacy are derived.

Structural perturbations in the Mn4CaO5 cluster site, an oxygen-evolving complex of photosystem II, such as those induced by Ca2+/Sr2+ exchanges or Ca/Mn-removal have been known to induce long-range positive shifts (+30 mV to +150 mV) in the redox potential of the primary quinone electron acceptor plastoquinone A (QA) located 40 Å distant from the OEC. Here, we reanalyzed the crystal structure of Sr-PSII solved at 2.1 Å and compare it with the native Ca-PSII of 1.9 Å with focus on the acceptor site and report on the possible long-range interactions between the donor, Mn4Ca(Sr)O5 cluster, and acceptor sites.

The growing interest in heat-conducting nanofluids requires highly sensitive methods for analyzing thermal properties. Thermal-lens spectrometry, despite its advantages over classical methods, does not have a general approach to measuring and interpreting results for dispersed systems. In this paper, by the example of nanofluids of silicon oxide in water in a wide range of concentrations and sizes, the selection of measurement parameters for transient and steady-state thermal lensing is justified, and the interpretation of the results of thermal diffusivity measurements is substantiated. The features of measurements of thermal diffusivity by thermal lens spectrometry under stationary state for dispersed systems are considered. Using this approach, it is possible to detect and distinguish thermal effects with high accuracy. For dispersions of silicon oxide, with increasing concentration, the thermal diffusivity passes through a minimum. Silicon oxide dispersions can be used both as a coolant or as a heat-removing liquid by selecting the particle size and concentration.

Steam boiler has a significant role in the industrial sector. The failure in boiler tubes significantly reduces the availability of the plant. Furthermore, deposits on the inner tube wall contribute to such failure by changing the thermal resistance of the wall, which causes a significant increase in the tube wall's temperature and, consequently, lower allowable stress. The presented thermal-fluid model is developed for the water tube. The model is implemented using ANSYS FLUENT to estimate the wall maximum water tube wall temperature considering the deposits layer and then determine the minimum thickness of the tube wall via ASME standards to assure safe operation. The model is verified via a mesh independence test. The minimum tube thickness is recommended and justified given the thermo-mechanical performance of the water tubes at several operating loads of 50, 75, and 100 %. These loads are implemented by different convective heat transfer coefficients of flue gases under different deposit thicknesses, thermal conductivity, and flue gas temperature. The present work contributes to the literature by recommending the minimum thickness of the water wall tubes and highlighting the thermo-mechanical effect of the deposits on water tube resilience under different operating conditions.

Using structured light to drive colloidal motors, due to its advantages of remote manipulation, energy tunability, programmability, and controllability of spatiotemporal distribution, has been attracting much attention in the fields of targeted drug delivery, environmental control, chemical agent detection, and smart device design. Here, we focus on studying the group control of colloidal made from a photo-responsive organic polymer molecule NO-COP (N,O-Covalent organic polymer). These colloidal motors mainly respond to the light intensity patterns. We chose a digital micromirror device (DMD) to modulate the structured light field shining on the sample, by considering its merit of fast refreshing speed, good programmability, and high-power threshold. It is found that under ultraviolet or green light modulation, such colloidal motors exhibit various group behaviors including group diffusion, group patterning, and group migration. The qualitative interpretation is also provided for these observations.

Biopolymers are of growing interest, but to improve some of their poor properties and performance, it is required the formulation of bio-based blends and/or adding of nanoparticles. For this purpose, in this work, two different metal oxides, such as zinc oxide (ZnO) and titanium dioxide (TiO2), at different concentrations (0.5, 1 and 2 %wt.) have been added in polylactic acid (PLA) and polylactic acid/polyamide 11 (PLA/PA11) blends to establish their effects on solid-state properties, morphology, melt behaviour, and photo-oxidation resistance. It seems that the addition of ZnO in PLA leads to a significant reduction of its rigidity probably due to an inefficient dispersion in the melt state, while the addition of TiO2 does not penalise PLA rigidity. Interestingly, the addition of both ZnO and TiO2 in PLA/PA11 blend has a positive effect on the rigidity because of blend morphology refinement and leads to a slight increase in film hydrophobicity. The photo-oxidation resistance of neat PLA and PLA/PA11 blend is significantly reduced due to the presence of both metal oxides, and this must be considered when designing the potential applications. The last results suggest that both metal oxides could be considered as photo-sensitive degradant agents for biopolymer and biopolymer blends.

Land degradation monitoring and assessment in the Sahel zone has relied substantially on temporal trends of remote sensing-based vegetation indices, which are proxies for the bioproductivity of the land. However, prior studies have shown that negative or positive trends in bioproductivity are not necessarily associated with degradation or improvement of land condition. In this short communication, while acknowledging the contributions of remote sensing-based indices and global-scale datasets to dismantling an outdated desertification narrative, we argue that local land users have much to contribute to our understanding of land degradation, and particularly to ensuring that scientific assessments of degradation capture variables relevant to them. We used the participatory photo elicitation method in three sites in the Senegalese Ferlo in order to elicit local pastoralists’ perspectives on land degradation and identify the indicators that they use to characterize pasture quality, while empowering them to lead the discussion. The discussion revealed indicators far beyond bioproductivity, including livestock performance as well as composition and quality of the herbaceous and woody vegetative cover, invasive species, soil quality and water availability. We found that the pastoralists’ knowledge and interest in the issue could potentially be harnessed more systematically, and at larger scales, in order to build a spatially explicit field-based knowledge base of land degradation complementary to remote sensing-based maps of trends in bioproductivity. Such a dataset could serve as a standalone product or as a reference dataset for development and validation of remote sensing-based indicators.

The kinetics and optimal efficacy conditions of photoinitiated polymerization are theoretically presented. Analytic formulas are derived for the crosslink time, crosslink depth and efficacy function. The roles of photosensitizer (PS) concentration, diffusion depth and light intensity on the polymerization spatial and temporal profiles, for both uniform and non-uniform cases, are presented . For optimal efficacy, a strategy via controlled PS concentration is proposed, where re-supply of PS in high light intensity may achieve a combined-efficacy similar to low light intensity, but has a much faster procedure. A new criterion of efficacy based on the polymerization (crosslink) [strength] and [depth] is introduced.

Stimuli-responsive polymeric materials have attracted significant attentions in a variety of high-value-added and industrial applications during the past decade. Among various stimuli, light is of particular interest as a stimulus due to its unique advantages such as precisely spatiotemporal control, mild conditions, ease of use, and tunability. In recent years, a lot of effort toward synthesis of biocompatible and biodegradable polypeptide has resulted in many examples of photo-responsive nanoparticles. Depending on the specific photochemistry, those polypeptide derived nano-assemblies are capable of crosslinking, disassembling, or morphing into other shapes upon light irradiation. In this mini-review, we aim to assess the current state of photo-responsive polypeptide based nanomaterials. First, those “smart” nanomaterials will be categorized by their photo-triggered events (i.e., crosslinking, degradation, and isomerization) which are inherently governed by photo-sensitive functionalities including o-nitrobenzyl, coumarin, azobenzene, cinnamyl, and spiropyran. In addition, the properties and applications of those polypeptide nanomaterials will be highlighted as well. Finally, the current challenges and future directions of this subject will be evaluated.

In the presented paper, a comprehensive study will be done on shape factor analysis of MoS2-GO in H2O-C2H6O2 based hybrid nanoliquids associated with effect and influence of transverse magnetic field and thermal radiation. The effect of variation in different parameters and nanoliquids shapes under temperature and velocity distribution is explored and also non-linear thermal radiation will be analyzed. Algorithms are introduced in proportion to mathematical modeling based on their numerical results and comparative curves for further explanation. In addition, it will be done research for influence and effect of new significant parameters emerged to the model to do sensitivity analysis and also their output results are demonstrated, examined and compared together by presenting graphs and tables. Based on detailed discussions, authentication of attained results designates the high accuracy of applied methods deployed to solve presented model in the paper. Our results satisfy that our used approach is accurate, highly reliable and also effective. All mentioned steps will be described throughout the literature.

The coombs (in Catalan comes) form an integral part of the landscape. These are small valleys, with the deepest and flattest part cultivated for agriculture. They are predominantly found in the most arid regions of Catalonia, particularly around the cities of Tarragona and Lleida. They are generally dry land areas. We propose that these coombs gained significance in the early centuries of the Middle Ages, a period marked by intense erosion. It is important to identify their locations and establish connections with medieval written documents, the settlements that thrived throughout the Middle Ages, archaeological sites such as necropolises, and the valuable data derived from to-ponymy studies. We think that understanding these coombs can greatly contribute to under-standing how the territory was organized in the Middle Ages, the extent of cultivated lands that were established, and the distribution of many settlements. Ultimately, this knowledge can aid in acquiring better understanding of the current landscape.

Due to an increase of the monocrystalline PV systems installations, for a drive towards the sustainable smart cities in the hot arid developing country such as Pakistan, pose challenges of the performance and degradation issues. Monocrystalline PV module efficiencies are declining and damaging under the continuous exposure to higher surface day-time temperatures in the different parts of the country. A MATLAB simulations were performed based on the validated mathematical approach. This paper investigates the hot arid surface temperature impacts on the performance of PV modules during the summer and winter seasons in Pakistan. The investigations are performed examining the power generating efficiency of the PV system. This paper also investigates the influence of installations of PV-system in the North, South, East and West regions of Pakistan. It was examined that the northern areas of Pakistan are more suitable for maintaining the long-term durability of the PV system. Investigations are performed for the peak summer and peak winter days. During summer months, cooling strategies have to be implemented to overcome the heating effects whilst reducing degradation effect on installed PV-system.

In this research paper a novel Ultra Violet Photo Catalyst Oxidation (UVPCO) sensor for air and surface sanitization using Common Source (CS) amplifier is presented. The ultra violet photo catalysis is the process in which the highly reactive radicals like H+, OH-and peroxides ions are produced from air in the presence of the ultra violet radiation and photo catalyst. In this process, the free radicals outbreaks the bio aerosols like bacteria, fungus and volatile organic compounds (VOCs) and destroy them. The proposed system is relies on the fast operation of PCS which operates under sub-threshold conditions and reduced computation time. The properties of common source amplifier like very high voltage gain and input output resistance increased the sensitivity as well as stability of the circuit. The system is more user friendly and the outcomes of simulation are fairly in agreement with the theoretical estimation. Keywords: bio aerosol, Photo Catalytic Oxidation (PCO), hydroxyl, hydrogen peroxide, SPICE, surface sanitizer.

In the present paper, the effect of the non-linear thermal radiation on the neutral gas mixture in the unsteady state is investigated for the first time. The unsteady BGK technique of the Boltzmann kinetic equations for a neutral non-homogenous gas is solved. The solution of the unsteady case makes the problem more general significance than the stationary one. For this purpose, the moments' method, together with the traveling wave method, is applied. The temperature and concentration are calculated for each gas component and mixture for the first time.Furthermore, the study is held for aboard range of temperatures ratio parameter and a wide range of the molar fraction. The distribution functions are calculated for each gas component and the gas mixture. The significant non-equilibrium irreversible thermodynamic characteristics the entire system is acquired analytically. That technic allows us to investigate the consistency of Boltzmann's H-theorem, Le Chatelier principle, and thermodynamics laws. Moreover, the ratios among the different participation of the internal energy alteration are evaluated via the Gibbs formula of total energy. The final results are utilized to the argon-helium non-homogenous gas at different magnitudes of radiation force strength and molar fraction parameters. 3D-graphics are presented to predict the behavior of the calculated variables, and the obtained results are theoretically discussed.

The aim of this study is to analyse problems related to thermal mapping obtained from thermal data acquired from Unmanned Aerial Systems (UAS) equipped with thermal cameras. We focused on an accurate analysis of uncertainties introduced by the PIX4D Mapper software used to obtain the surface temperature maps of thermal images acquired by the UAS. To achieve this aim, we used artificial thermal reference during the surveys, as well as natural hot targets, i.e. thermal anomalies in the Pisciarelli hydrothermal system in Campi Flegrei caldera (CFc). Artificial thermal targets, expressly created and designed for this goal, are a prototype here called “developed thermal target” (DTT) made by the drone Laboratory at Istituto Nazionale di Geofisica e Vulcanologia - Osservatorio Vesuviano (INGV-OV). We show the results obtained by three surveys during which thermal targets were positioned on land at different flight heights of the UAS. Different heights were also necessary to test spatial resolution of the DTT with the used thermal camera as well as possible temperature differences between the raw images acquired by UAS with the thermal mapping obtained from the PIX4D Mapper software. In this work we have estimated the uncertainty that may be introduced by the mosaic procedure and furthermore we find an attenuation of the measured temperatures introduced by the different distances between the thermal anomaly and sensor. These results appear to be of great importance for the subsequent calibration phase of the thermal maps especially in cases where these methodologies are applied for monitoring purposes of volcanic/geothermal areas.

In recent years, several alternatives for improving the thermal comfort conditions inside buildings have been proposed. Among these alternatives, Thermally Activated Building Systems (TABS) have become of interest due to the benefits this technology brings to the building sector. The TABS are embedded in different building components and exchange heat with building envelope to improve the indoor air temperature. This review presents relevant results presented in the literature on the thermal behavior of TABS, the different types of TABS configurations, and the main parameters of TABS studied such as pipe separation, fluid inlet temperature, fluid velocity, and volumetric flow rate. The potential of TABS to improve thermal comfort conditions and provide energy savings is also discussed. Further, this study presents the different modes of application.

Carbohydrate and menthol mouth-swilling have been used to enhance exercise performance in the heat. However, these strategies differ in mechanism and subjective experience. Participants (n=12) sat for 60 min in hot conditions (35°C; 15±2%), following a 15 min control period, participants undertook three 15 min testing blocks. A randomised swill (Carbohydrate; Menthol; Water) was administered per testing block (one swill every three minutes within each block). Heart rate, tympanic temperature, thermal comfort, thermal sensation and thirst were recorded every three minutes. Data were analysed by ANOVA, with carbohydrate intake controlled for via ANCOVA. Small elevations in heart rate were observed after carbohydrate (ES: 0.22 ± 90% CI: -0.09 to 0.52) and water swilling (0.26; -0.04 to 0.54). Menthol showed small improvements in thermal comfort relative to carbohydrate (-0.33; -0.63 to 0.03) and water (-0.40; -0.70 to -0.10), and induced moderate reductions in thermal sensation (-0.71; -1.01 to -0.40 and -0.66; -0.97 to -0.35, respectively). Menthol reduced thirst by a small to moderate extent. These effects persisted when controlling for dietary carbohydrate intake. Carbohydrate and water may elevate heart rate, whereas menthol elicits small improvements in thermal comfort, moderately improves thermal sensation and may mitigate thirst; these effects persist when dietary carbohydrate intake is controlled for.

In this paper, the effect of microstructure on the thermal conductivity of plasma-sprayed Y₂O₃ stabilized ZrO₂ (YSZ) thermal barrier coatings (TBCs) is investigated. Nine freestanding samples deposited on aluminum-base superalloy are studied. Cross-section morphology such as pores, cracks, m-phase content, grain boundary density of the coated samples are examined by scanning electron microscopy (SEM) and electron back-scattered diffraction (EBSD). Multiple linear regressions are used to develop quantitative models which describe the relationship between the particle parameters, m-phase content and the microstructure such as porosity, crack-porosity, the length density of small-angle-crack and the length density of big-angle-crack. Moreover, the relationship between microstructure and thermal conductivity is investigated. Results reveal that the thermal conductivity of the coating is mainly determined by the microstructure and grain boundary density at room temperature (25 ℃) and by the length density of big-angle-crack, monoclinic phase content and grain boundary density at high temperature (1200 ℃).

Graphene and borophene are highly attractive two-dimensional materials with outstanding physical properties. In this study we employed a combined atomistic continuum multiscale modeling to explore the effective thermal conductivity of polymers nanocomposites made of PDMS polymer as the matrix and graphene and borophene as nanofillers. We first conduct classical molecular dynamics simulations to investigate the interfacial thermal conductance between graphene/PDMS and borophene/PDMS interfaces. Acquired results confirm that the interfacial thermal conductance between nanosheets and polymer increases from the single-layer to multilayered nanosheets and finally converges. The data provided by the atomistic simulations were then used in the finite element method simulations to evaluate the effective thermal conductivity of polymer nanocomposites at continuum level. We explore the effects of nanofillers type, their volume content, geometry aspect ratio and thickness on the nanocomposites effective thermal conductivity. As a very interesting finding, we show that borophene nanosheets, despite almost two orders of magnitude lower thermal conductivity than graphene, can yield very close enhancement in the effective thermal conductivity in comparison with graphene, particularly for low volume content and small aspect ratios and thicknesses. We conclude that for the polymer-based nanocomposites, significant improvement in the thermal conductivity can be reached by improving the bonding between the fillers and polymer or in another word enhancing the thermal conductance at the interface. By taking into account the high electrical conductivity of borophene, our results suggest borophene nanosheets as promising nanofillers to simultaneously enhance the polymers thermal and electrical conductivity.

What proportions should a thermally massive building have? How should the thermal mass be distributed? Should the "massing" change with the choice of material? This paper shows how to optimize the physical proportions of a building so that it synchronizes ambient heat exchanges in a natural feedback cycle. The internal mass is thermally coupled with buoyancy ventilation; the cycle is driven by the daily swing of outdoor temperature. Tripling up functions in this way—so that structural materials can reliably cool and power the ventilation for buildings—could help decarbonize the construction industry and provide an effective strategy for adapting to life-threatening heatwaves. Based on harmonic analysis, the method allows designers to thermally tune the form and mass of a building to meet chosen targets for temperature and ventilation in free-running mode. Once the optimal balance of exchange rates is known, design teams can proportionally vary the building height and ventilation openings against the surface area and thickness of an internal thermal mass. The possible permutations are infinite but parametrically constrained, allowing teams to fairly compare the functional and environmental credentials of different construction materials while they produce and evaluate preliminary options for organizing the exterior form and interior spaces of a building. An example study suggests that thin-shell structures of minimum weight, and even timber buildings, may be optimally tuned to produce ample ventilation and temperature attenuation.

Traditional graphene-based films normally possess high thermal conductivity (TC) only along single direction, which is not suitable for thermal interface materials (TIMs). Here, a graphene film with excellent bidirectional TC and mechanical properties was prepared by hot-pressing super-elastic graphene aerogel (SEGA). Thermal annealing at 1800℃ improves the further restacking of graphene sheets, bring the SEGA high structure stability for enduring the hot-pressing process. The junctions and nodes between the graphene layers in the hot-pressed SEGA (HPSEGA) film provide bidirectional heat transport paths. The in-plane TC and through-plane TC of HPSEGA film with thickness of 101μm reach 740 Wm-1K-1 and 42.5 Wm-1K-1, respectively. In addition, HPSEGA film with higher thickness still maintains excellent thermal transport properties due to the interconnected structure reducing the effect of the defects. The infrared thermal images visually manifest the excellent thermal-transfer capability and thermal dissipation efficiency of the HPSEGA films, indicating the great potential as advanced bidirectional TIMs.

A variety of factors ranging from ethnicity and occupants’ lifestyles to local climatic characteristics of any studied location and people’s age factors can affect thermal comfort assessment globally. Due to the detrimental impact of climate change, the building industry has started to implement energy efficiency schemes while considering the thermal comfort of vulnerable population both for the society and any sphere of economy. Although, considering human-based approaches have been neglected by other scholars in thermal comfort studies. This paper reviews energy effectiveness of state-of-the-art passive systems in providing neutral adaptive thermal comfort for elderly people, through exploring passive design strategies in four distinct climates namely, Canada, India, Abu Dhabi and the South-eastern Mediterranean basin. The aim of the study is to analyze the available data provided by the ASHRAE Global Thermal Comfort Database II version record 2.1. The main objective of the study is to develop an effective methodological framework for the on-going development of adaptive thermal comfort theory. To this extend, this study presents a comprehensive review on the assessment of energy effectiveness of passive design systems. To accomplish this, the impact of climate change factor in passive design systems was investigated. The meta-analysis method was adopted to determine the input variables for the statistical analysis. Cramer’s V and Fisher’s Exact tests were used to assess occupants’ thermal sensation votes (TSVs). The findings revealed that there are discrepancies detected between the in-situ field experiments and the data recorded in the ASHRAE Global Thermal Comfort Database II. According to the Köppen-Geiger climate classification, it was found from the study that the slightly high temperature fluctuations were identified in India where the weather is dry and savanna climate. The study findings contribute to the development of adaptive thermal comfort theory by reviewing the existing methodologies globally. Furthermore, a critical review on the significance of occupants’ age differences should be conducted in the identification of neutral adaptive thermal comfort.

A thermal-oxidative aging test at 120°C was condutcted on Ethylene Propylene Diene Monomer (EPDM) vulcanizates of the semi-efficient vulcanization system. The effect of thermal-oxidative aging on EPDM vulcanizates was systematically studied by curing kinetics, aging coefficient, cross-linking density, macroscopic physical properties, contact angle, Fourier Transform Infrared Spectrometer (FTIR), Thermogravimetric analysis (TGA) and thermal decomposition kinetics. The results show that the content of hydroxyl and carbonyl groups as well as the carbonyl index increased with increasing aging time, indicating that EPDM vulcanizates are gradually oxidized and degraded. As a result, the EPDM vulcanized rubber chains were cross-linked, and its conformational transformation was limited and its flexibility was weakened. The thermogravimetric analysis demonstrates the thermal degradation of EPDM vulcanizates had competitive reactions of cross-linking and degradation, and the thermal decomposition curve can be divided into three stages, meanwhile the thermal stability of EPDM vulcanizates gradually decreases with the increase of aging time. The introduction of antioxidant in the system can promote the cross-linking speed and reduce the cross-linking density of EPDM vulcanizates, while inhibiting the surface thermal and oxygen aging reaction. This is attributed to the fact that the antioxidant can reduce the thermal degradation reaction level, but it is not conducive to the formation of a perfect crosslinking network structure and reduce the activation energy of thermal degradation of the main chain.

Thermal infrared imagery provides temperature information on target objects, and has been widely applied in non-destructive testing. However, thermal infrared imagery is not always able to display detailed textures of inspected objects, which hampers the understanding of geometric entities consisting of temperature information. Although some commercial software has been developed for 3D thermal model displays, the software requires the use of expensive specific thermal infrared sensors. This study proposes a cost-effective method for 3D thermal model reconstruction based on image-based modeling. Two smart phones and a low-cost thermal infrared camera are employed to acquire visible images and thermal images, respectively, that are fused for 3D thermal model reconstruction. The experiment results demonstrate that the proposed method is able to effectively reconstruct a 3D thermal model which extremely approximates its corresponding entity. The total computation time for the 3D thermal model reconstruction is intensive while generating dense points required for the creation of a geometric entity. Future work will improve the efficiency of the proposed method in order to expand its potential applications to in-time monitoring.

Modelling water vapour flow, heat transfer and porosity in porous adsorbent is somewhat challenging simulation problem. Primary macroscopic water vapour flow models, such as Darcy's law, fail to predict the pressure drop entirely correctly for the reason that many of flow parameters not considered because of the simplifications that remain made for the multi-scale structure of the porous adsorbents. For one to develop a good physical understanding of such water vapour flows and the accuracy of existing 3D simulation models, there is a need for some accurate 3D geometry to be studied. This present work describes two-phase water vapour flow and adsorption/ desorption performed on porous adsorbent by a Dynamic vapour sorption (DVS). The CFD simulation results are associated with experiments results. It is decided that for such complex porous adsorbent CFD simulation problems the use of COMSOL Multiphysics and SolidWorks flow simulation will be utilised.

Laser-induced functionalisation using excimer laser irradiation has been widely applied to transparent conductive oxide films. However, exploring suitable irradiation conditions is time-consuming and cost-ineffective as there are numerous routine film fabrication and analytical processes. Thus, we herein explored a real-time technique to monitor the laser-induced functionalisation of transparent conductive oxide films. We developed two types of monitoring apparatus, electrical and optical, and applied them to magnetron-sputtered Sn-doped In2O3 films grown on glass substrates and hydrogen-doped In2O3 films on glass or plastic substrates using a picosecond Nd:YAG pulsed laser. Both techniques could monitor the functionalisation from a change in properties of the films on glass substrates by laser irradiation, but electrical measurement was unsuitable for plastic samples because of a laser-induced degradation of the underlying plastic substrate, which harmed proper electrical contact. Instead, we demonstrated that the optical properties in the near-infrared region were suitable for the monitoring and the changes in the optical properties were visually detected in real-time by using a near-infrared camera.

The performance of ground heat exchangers systems depends on the knowledge of the thermal parameters of the ground like thermal conductivity, thermal capacity and diffusivity. The knowledge of these parameters often requires quite accurate experimental analysis, known under the name of Thermal Response Test (TRT). In this paper, after a general analysis of the various available types of TRT and the study of the theoretical basics of the method, the perspective of the definition of a simplified routine method of analysis based on the combination of a particular version of TRT and the routine geotechnical tests for the characterization of soil stratigraphy and of the ground characteristics, mandatory before the construction of a new buildings, even if limited to quite short drilling depth (lower than 30 m). The idea of developing TRT in connection with geotechnical test activity has the objective of promoting a widespread use of in-situ experimental analysis and of reducing TRT costs and time duration of the experimental analysis. The considerations exposed in the present paper lead to reconsider a particular variety of the TRT in particular the version known as Thermal Response Test while Drilling (TRTWD).

The internet of things and growing demand for smaller and advanced devices has created the problem of high heat production in the electronic equipment which greatly reduces the work performance and life of the electronic instruments. Thermal interface materials (TIMs) are placed in between heat generating micro-chip and the heat dissipater to conduct all the produced heat to the heat sink. Development of suitable TIMs with excellent thermal conductivity (TC) in both in-plane and through-plane directions is a very important need at present. For efficient thermal management, polymer composites are potential candidates. But in general their thermal conductivity is low compared to that of metals. The filler integration into the polymer matrix is one of the two approaches used to increase the thermal conductivity of polymer composites and is also easy to scale up for industrial production. Another way to achieve this is to change the structure of polymer chains, which fall out of the scope of this work. In this review, considering the first approach, the authors have summarized recent development in many types of fillers with different scenarios by providing multiple cases with successful strategies to improve through-plane thermal conductivity (TPTC) (K⊥). For better understanding of TC the comprehensive background is also presented. In the end, it is given a detailed conclusion which provides drawbacks of some filler, multiple significant routes recommended by other researchers to build Thermally Conductive Polymer Composites, future aspects along with direction so that the researchers can get a guideline to design an effective polymer based Thermal interface materials. A number of methods to improve the effective (out-plane) thermal conductivity of polymer composites are also discussed.

The manufacturing method influences the properties of the produced components. This work investigates the influence of manufacturing methods such as fused filament fabrication (3D printing) and injection molding on water absorption, mechanical and thermal properties of the specimens produced from neat biobased poly(lactic acid) (PLA) polymer and poly(lactic acid)/wood composites. Acrylonitrile butadiene styrene (ABS) acts as the reference material due to its low water absorption and good functional properties. The printing layer thickness is one of the factors that affects the properties of a 3D printed specimen. The investigation includes two different layer thicknesses (0.2 mm and 0.3 mm) while maintaining uniform overall thickness of the specimens across two manufacturing methods. 3D printed specimens absorb significantly higher amounts of water than the injection molded specimens, and the increase in the layer thickness of the 3D printed specimens contributes to further increased water absorption. However, the swelling due to water absorption in 3D printed specimens decreases on increased layer thickness. Tensile, flexural and impact properties of all the specimens decrease after water absorption while the properties improve on decreasing the layer thickness. Higher porosity on increasing the layer thickness is the predominant factor. The results from dynamic mechanical analysis and microscopy validate the outcomes.

The study sought to determine solar irradiation in Homa Bay County which can be tapped and utilized in improving lives of residents of the region by converting the solar thermal energy in Home Bay to other forms of energy such as electric form, mechanical form and light. The study was done by assessing the local atmospheric conditions which included sunshine duration data and air temperature records for the period of two years and the data obtained subjected to statistical analysis to determine the localized characteristics of the resource. The characteristics that were examined include; seasonal and annual power expectations as well as resource reliability. The solar irradiance of Home County was found to be 768.0 W/m².

The main development direction of energy efficiency technologies in construction is the creation of various materials with a complex structure and unique strength, thermal and other properties. The aerogel is a material with high porosity and excellent thermal insulation properties. This paper provides the state-of-the-art of aerogel applications for the additive manufacturing of energy efficient buildings. This work provides the experimental and numerical assessment results of thermal conductivity of aerogel-enhanced blanket, the experimental assessment results of thermal performance of aerogel-enhanced building structure, the experimental assessment results of the aerogel application as mixture powder component of the concrete mixture to printing building and the experimental assessment results of the aerogel application as parget powder component. Experimental results show the effect of aerogel powder component application: thermal conductivity decreased by 25%.

The paper presents theoretical, experimental and numerical studies on the thermal behavior of mineral wool used in sandwich panels. The aim of this study is to investigate the thermal properties of mineral wool at elevated temperatures and provide a simple model that would allow to determine the heat propagation in sandwich panels during fire. The paper proposes a new method to experimentally evaluate thermal diffusivity, derived from theoretical premises. Experiments are conducted in a laboratory furnace, where specimens are placed and temperatures inside specimens are measured. Different methods are used to process the test results and calculate the thermal diffusivity of mineral wool. Finally, a numerical analysis of heat transfer using finite element method (FEM) is performed to validate the obtained thermal properties.

This work shows the potential of a new way of co-treatment of domestic wastewater (DWW) and a liquid stream coming from the thermal hydrolysis of the organic fraction of municipal solid waste (OFMSW) mediated by a mixed culture of purple phototrophic bacteria (PPB) capable of assimilating carbon and nutrients from the medium. The biological system is an open single-step process operated under microaerophilic conditions at an oxidative reduction potential (ORP) &lt; 0 mV with a photoperiod of 12/24 h and fed during the light Stage only, so the results can be extrapolated to outdoors open ponds operation by monitoring the ORP. The effluent mostly complies with the discharge values of the Spanish legislation in COD and P values (&lt;125mg/L &lt;2 mg/L), respectively, and punctually on values in N (&lt;15mg/L). Applying an HRT of 3 d and a ratio of 100:7 (COD:N), the presence of PPB in the mixed culture surpassed 50% of 16S rRNA gene copies, removing 78% of COD, 53% of N and 66% of P. Furthermore, increasing the HRT to 5 d, removal efficiencies of 83% of COD, 65% of N and 91% of P were achieved. In addition, the reactors were further operated in a membrane bioreactor, thus separating the HRT from the SRT to increase the specific loading rate. Very satisfactory removal efficiencies were achieved by applying HRT and SRT of 2.3 and 3 d, respectively: 84% of COD, 49% of N and 93% of P despite low presence of PPB due to more oxidative conditions, which anyway step-by-step re-colonized the mixed culture until reaching &gt;20% of 16S rRNA gene copies after 49 d of operation. These results open the door to scale up the process in open photobioreactors capable of treating urban wastewater and municipal solid waste in a single stage and under microaerophilic conditions by controlling the ORP of the system. This novel urban biorefinery allows reducing treatment costs of two urban wastes and embed them in the circular bioeconomy through water recycling and valorizing PPB biomass as a source of carbon, nitrogen and phosphorus.

Verteporfin, a free base benzoporphyrin derivative monoacid ring A, is a photosensitizing drug for photodynamic therapy (PDT) used in the treatment of the wet form of macular degeneration and activated by red light of 689 nm. Here, we present the first direct study of its photofragmentation channels in the gas-phase, conducted using a laser interfaced mass spectrometer across a broad photoexcitation range from 250-790 nm. The photofragmentation channels are compared with the collision-induced dissociation (CID) products revealing similar dissociation pathways characterized by the loss of the carboxyl and ester groups. Complementary solution-phase photolysis experiments indicate that photobleaching occurs in verteporfin in acetonitrile; a notable conclusion, as photoinduced activity in Verteporfin was not thought to occur in homogenous solvent conditions. These results provide unique new information on the thermal break-down products and photoproducts of this light-triggered drug.

The diffusion coefficients of ions are measured in a microchip filled with a cationic charged 3D hydrogel in order to study the effect of cationic charged 3D hydrogel on the diffusivity of ions. In this study, poly-diallyl-dimethyl-ammoniumchloride (poly-DADMAC) is used to produce a 3D hydrogel. Four different fluorophores are used in the 3D hydrogel rhodamine 6G, rhodamine-BSA, fluorescein isothio-cyanate (FITC) and FITC-BSA. The rhodamine 6G and rhodamine-BSA are positively charged (cations), while fluorescein isothio-cyanate (FITC) and FITC-BSA are negatively charged (anions). Two widely used techniques which are short time diffusivity measurement technique and long time diffusivity measurement techniques are used to measure the diffusion coefficients. For the short time measurement, Fluorescence recovery after photo-bleaching (FRAP) is used by a 3D confocal microscope. For the long time measurement, fluorescence images are taken for 11 days to observe a pure diffusivity without any convective movement. As a result, the diffusivity of the cations was found to be lower than that of the anions in the cationic charged hydrogel.

Carbon nanotubes have been attracting considerable interest among material scientists, physicists, chemists and engineers for almost 30 years. Owing to their high aspect ratio, coupled with remarkable mechanical, electronic and thermal properties, carbon nanotubes have found application in diverse fields. In this review, we will cover the work on carbon nanotubes used for sensing applications. In particular, we will see examples where carbon nanotubes act as main players in devices sensing biomolecules, gas, light or pressure changes. Furthermore, we will discuss how to improve the performance of carbon nanotube-based sensors after proper modification.

In this investigation, polymethyl methacrylate (PMMA) was mixed with cyclic olefin copolymer (COC) because of its hardness, strength, and transparency properties. The results of thermal analysis through TGA and DTG showed that the thermal properties of the alloy are improved using 40% cyclic olefin copolymer. Kinetics of thermal degradation (pyrolysis) of polymers have been studied and analyzed and thermal pyrolysis of polymethyl methacrylate and cyclic olefin copolymer thermoplastic polymer was conducted. The computation of kinetic analysis is measured along with the different methods used to study the kinetics. The activation energy (E) of degradation of studied materials was estimated using Ozawa Flynn and Wall (OFW), Starink and Kissinger’s methods, and evaluation of three kinetic parameters taken appropriate kinetic model in terms of percent change for both types of polymers have been proposed, and finally, simulated curves were compared with the experimental curves. Both mechanisms of degradation for COC and PMMA under nitrogen atmosphere will reflect intramolecular transfer and random scission of the main chain.

Polymer composites with high thermal conductivity have a great potential for applications in modern electronics due to their low cost, easy process, and stable physical and chemical properties. Nevertheless, most polymer composites commonly possess unsatisfactory thermal conductivity, primarily because of the high interfacial thermal resistance between inorganic fillers. Herein, we developed a novel method through silver functionalized graphene nanosheets (GNS) and multiwalled carbon nanotube (MWCNT) composites with excellent thermal properties to meet the requirements of thermal management. The effects of composites on interfacial structure and properties of the composites were identified, and the microstructures and properties of the composites were studied as a function of the volume fraction of fillers. An ultrahigh thermal conductivity of 12.3 W/mK for polymer matrix composites was obtained, which is an approximate enhancement of 69.1 times compared to the polyvinyl alcohol (PVA) matrix. Moreover, these composites showed more competitive thermal conductivities compared to untreated fillers/PVA composites applied to the desktop central processing unit, making these composites a high-performance alternative to be used for thermal management.

In the present work, three different atmospheric plasma sprayed (APS) alumina coatings were fabricated using three fused and crushed alumina powders of different particle size fine, medium and coarse. The influence of the particle size on thermal properties and micro-structural features of the produced coating were investigated by thermal insulation test and detailed image analysis technique, respectively. The analyzed micro-structural features include the total porosity, pore size (fine, medium, and large) and cracks. All types of cracks were considered in calculations as voids and were evaluated according to their sizes as pores. All spray parameters except the particle size were fixed throughout the spraying process. The results revealed that the fine starting powder has produced the densest coating with the lowest total porosity and that the total porosity increases with an increasing particle size. This was expected as powders of smaller particle size will reach a higher in-flight temperature and velocity than powders of bigger particle sizes as long as the same spray parameters are applied. However, a detailed image analysis investigation on the three produced coatings showed that the fraction of fine pores and cracks versus the total porosity is substantially higher in coatings produced by using fine starting powders than those produced using medium and coarse powders. In this work, a connection between the thermal insulation and the porosity fraction, which includes fine pores and cracks, was revealed.

This article presents, for the first time, the efficacy and curing depth analysis of photo-thermal dual polymerization in metal (Fe) polymer composites for 3D printing of a 3-component (A/B/M) system based on the proposed mechanism of our group, in which the co initiators A and B are Irgacure-369, and charge-transfer complexes (CTC), respectively; and the monomer M is filled by Fe. Our formulas show the depth of curing (Zc) is an increasing function of the light intensity, but a decreasing function of the Fe and photoinitiator concentrations. Zc is enhanced by the additive [B] which produces extra thermal radical for polymerization under high temperature. The heat (or temperature) increase in the system has two components : (i) due to the light absorption of Fe filler, and (ii) heat released from the exothermic photopolymerization of the monomer. The heat is transported to the additive (or co-initiator) [B] to produce extra radical R' and enhance the monomer conversion function (CF). The Fe filler leads to temperature increase, but also limits the light penetration leading to lower CF and Zc, which could be overcome by the additive initiator [B] in thick polymers. Optimal Fe for maximal CF and Zc are explored theoretically.

BODIPY dyes have recently raised attention as potential photosensitizers. In this work, commercial and novel photosensitizers (PSs) based on BODIPY chromophores (haloBODIPYs and orthogonal dimers strategically designed with intense bands in the blue, green or red region of the Visible spectra and high singlet oxygen production) were covalently linked to mesoporous silica nanoparticles (MSNs) further functionalized with PEG and folic acid (FA). MSNs of approximately 50 nm in size with different functional groups were synthesized to allow multiple alternatives of PS-PEG-FA decoration of their external surface. Different combinations varying the type of PS (commercial Rose Bengal, Thionine and Chlorine e6 or custom-made BODIPY-based), the linkage design and the length of PEG are detailed. All the nanosystems were physicochemically characterized (morphology, diameter, size distribution and PS loaded amount) and photophysically studied (absorption capacity, fluorescence efficiency, and singlet oxygen production) in suspension. For the most promising PS-PEG-FA silica nanoplatforms, the biocompatibility in dark conditions and the phototoxicity under suitable irradiation wavelengths (blue, green, or red) at regulated light doses (10-15 J/cm2) were compared with PSs free in solution in HeLa cells in vitro.

People counting applications have been used in diverse applications. The ability and accuracy of thermal imaging over conventional image cameras has led to the implementation of thermal cameras in people counting applications. This paper present a thermal people counting smart glass windows. The people counting application would be remotely monitored from a single centralized PC station as it’s connected to a multiplex of mass monitoring of 20 thermal camera, all embedded into different glass windows. The thermal cameras would then be able to detect body temperatures of all individuals who pass through any of the camera range and also count the numbers of people who passed through the camera range. The data gotten can then be further utilized in various ways, example is in the control of air conditioning and lightening.

When designing the battery of an electric vehicle, different parameters must be considered to obtain the safest arrangement of the battery/modules/cells from the mechanical and thermal point of view. In this study, the thermal runaway propagation mechanism of lithium-ion cells is analyzed as a function of their arrangement within a battery pack in case of a fire propagation of a battery pack in which a thermal runaway has occurred. The objective is to identify which cell/module arrangement is most critical within the battery pack by microscopic analysis of the structure and chemical composition of the most damaged cells, both horizontally and vertically, of a battery belonging to a burnt vehicle. And their final condition has been compared with the condition of new cells of the same type. In this way the structure and chemical composition of the anode, cathode and separator after Thermal Runaway has been compared. This research has been carried out to obtain information to understand the mechanical properties of lithium-ion cells and their behavior after thermal runaway heating leading to the propagation of a fire. Through the analysis carried out, it is concluded that cells placed in a vertical arrangement have worse behavior than cells in a horizontal arrangement. Regarding the safety of the battery, the results of this study will allow to determine which arrangement and structure of the cells within the battery pack is safer against thermal runaway due to thermal failure.

Light-colored and transparent polyimide (PI) films with good high-temperature dimensional stability are highly desired for advanced optoelectronic applications. However, in practice, the simultaneous achievement of good optical and thermal properties in one PI film is usually difficult due to the inter-conflicting molecular design for the polymers. In the present work, a series of PI-SiO2 nanocomposite films (ABTFCPI) were developed based on the PI matrix derived from hydrogenated pyromellitic anhydride (HPMDA) and an aromatic diamine containing benzanilide and trifluoromethyl substituents in the structure, 2,2'-bis(trifluoromethyl)-4,4'-bis[4-(4-aminobenzamide)]biphenyl (ABTFMB). The inorganic SiO2 fillers were incorporated into the nanocomposite films with the form of colloidal nanoparticles dispersed in the good solvent of N,N-dimethylacetamide (DMAc) for the PI matrix. The derived ABTFCPI nanocomposite films showed good film-forming ability, flexible and tough nature, good optical transparency, and good thermal properties with the loading amounts of SiO2 up to 30 wt% in the system. The ABTFCPI-30 film with the SiO2 content of 30 wt% in the film showed the optical transmittance of 79.6% at the wavelength of 400 nm (T400) with a thickness of 25 μm, the yellow index (b*) of 2.15, and the 5% weight loss temperatures (T5%) of 491 oC, which are all comparable to those the pristine ABTFCPI-0 matrix without filler (T400=81.8%; b*=1.77; T5%=492 oC). Meanwhile, the ABTFCPI-30 film exhibited obviously enhanced high-temperature dimensional stability with the linear coefficients of thermal expansion (CTE) of 25.4×10-6/K in the temperature range of 50 to 250 oC, which is much lower than that of the AMTFCPI-0 film (CTE=32.7×10-6/K).