Over the last decades, the coated glass products, and especially the low-emissivity coatings have become a common building material used in modern architectural projects. More recently, these material systems became common in specialized glazing systems featuring solar energy harvesting. Apart from achieving the stability of optical parameters in multilayer coatings, it is also important to have improved control over the design of visual color properties of the coated glass. We prepare metal-dielectric composite (MDC) based multilayer thin-film structures using the RF-magnetron sputtering deposition and report on their optical and chromaticity properties in comparison with these obtained using pure metal-based Dielectric/Metal/Dielectric (DMD) trilayer structures of similar compositions. Experimentally achieved Hunter L, a, b values of MDC-based multilayer building blocks of coatings provide a new outlook on the engineering of future-generation optical coatings with better color consistency and developing approaches to broaden the range of achievable color coordinates and better environmental stability.

Dynamic mechanical analysis (DMA) is a versatile technique that complements the information given by the more traditional thermal analysis techniques such as differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and thermal mechanical analysis (TMA). Dynamic constants such as storage modulus, loss modulus, and loss factor are temperature dependent and provide information about interfacial bonding between reinforced fibre and polymer matrix of composite material. To study the above mentioned properties at the glass transition region, for unidirectional fibrous composites reinforced with continuous fibers a reliable model was applied. In particular, the composite material was considered as composed of three phases with the intermediate phase between matrix and fibres, the interphase, to have variable properties depending on those of main phases and the mode of preparation of the overall material. The glass transition temperature is defined as the point at which the specific volume versus temperature curve changes abruptly slope marking the region between rubbery polymer and glassy polymer nature. Hence, the behaviour of unidirectional fibrous composites was investigated at this region. Examination of the glass transition temperature, which constitutes an upper limit for the structurally important glassy region through the loss factor, was performed by its consideration as a combination of glass transition temperature of matrix and interphase.

The article describes the study of the properties of polytetrafluoroethylene, modified using natural layered silicates—serpentinite. It is shown that the introduction of a small amount of layered silicates significantly increases the tribological characteristics of the material. The additional introduction of magnesium nano-spinels facilitated the formation of an intercalated polymer-silicate nanocomposite.

Filament wound composite pipes are frequently used in the field were transmission of high pressured chemical fluids, disposal of industrial wastes, oil and natural gas transmission takes place. In oil and gas industry, the pipelines transporting heavy crude oil are subjected to variable pressure waves causing fluctuating stress levels in the pipes. Computational Fluid Dynamics Analysis was performed using Ansys 15.0 Fluent software to study the effects of these pressure waves on some specified joints in the pipes. Depending on the type of heavy crude oil being used, the flow behavior indicated a considerable degree of stress levels in certain connecting joints, causing the joints to become weak over a prolonged period of use. In this research comparison of various pipe joints was done by using different material and the output result of the stress levels of the pipe joints were checked so that the life of the pipe joints can be optimized by the change of material.

Polyhydroxyalkanotes (PHA) are bio-based microbial biopolyesters with stiffness, elasticity, crystallinity and degradability tunable by the monomeric composition, bio-production strategy and post-synthetic processing; they display biological alternatives for diverse technomers of petrochemical origin. This, together with the fact that their monomeric and oligomeric in vivo degradation products do not exert any toxic or elsewhere negative effect to living cells or tissue of humans or animals, makes them highly stimulating for various applications in the medical field. The article provides an overview of PHA application in the therapeutic, surgical and tissue engineering area, and reviews strategies to produce PHA at purity levels high enough to be used in vivo. Tested applications of differently composed PHA and advanced follow-up products as carrier materials for controlled in vivo release of anti-cancer drugs or antibiotics, as scaffolds for tissue engineering, as guidance conduits for nerve repair or as enhanced sutures, implants or meshes are discussed from both a biotechnological and a material-scientific perspective. Particular attention is devoted to the adaptation of traditional polymer processing techniques for production of medicine-related devices based on PHA, such as melt-spinning, melt extrusion, or solvent evaporation, and to emerging processing techniques like 3D-printing, computer-aided wet-spinning, laser perforation, or electrospinning.

The awareness of the existence in plants of bioactive compounds namely phytochemicals (PHYs), having health properties is progressively expanding. Therefore, their massive introduction in the normal diet, in food supplements, and their use as natural therapeutics to treat several diseases are increasingly emphasized by several sectors. Particularly, most PHYs possessing antifungal, antiviral, anti-inflammatory, antibacterial, antiulcer, anti-cholesterol, hypoglycemic, immunomodulatory, and antioxidant properties have been isolated from plants. Additionally, their secondary modification with new functionalities, to further improve their intrinsic beneficial effects, is extensively investigated. Unfortunately, although the idea of exploiting PHYs as therapeutics is amazing, its realization is far from simple, and the possibility of exploiting them as effective orally administrable drugs is almost utopic. Most PHYs are insoluble in water and, when introduced orally, they scarcely reach the site of action in therapeutic concentrations. Degradation by enzymatic and microbial digestion, occurring in the mouth, stomach, and intestine, as well as fast metabolism and rapid excretion via the kidney, biliary, or lung, strongly limit their in vivo activity. To overcome these drawbacks, several nanotechnological approaches have been used and many PHYs-loaded delivery systems with dimensions of nanometers have been developed. This paper, also by reporting various recent case studies, reviews the foremost nano-suspension and nano-emulsion-based techniques developed for formulating the most relevant PHYs in more bioavailable nanoparticles (NPs), suitable or promising for clinical application. Also, the acute and chronic toxic effects due to the exposure to NPs reported so far, the possible nanotoxicity which could derive by their massive employment, as well as the ongoing actions to improve the knowledge in the field were discussed. The state of the art concerning the actual clinical application of both PHYs and the nanotechnologically engineered PHYs was also reviewed.

Recently perovskite solar cells have been paying attention of researchers. This comes from their high efficiency and stability. In this work, the change of some Optical and Electrical Properties of BaxFe(1-x)TiO4 thin films due to the change of the nanocrystal spacing and size were studied. A simple theoretical model based on the string theory was utilized to explain some of these empirical relations. The empirical results obtained indicated that an increase in the efficiency of the nano solar cell requires the energy gap to be narrow. Decreasing the nanocrystal size and spacing caused the energy gap to become narrower. The energy gap decreases also upon increasing the absorption coefficient and decreasing the transmission. This also requires increasing the conductivity and the magnetic permeability. The increase of the nanocrystal spacing decreases the absorption coefficient, electrical conductivity, and magnetic permeability, while it causes the transmission to increase. All these changes are explained using a simple string model beside Newton's laws. The capability of the string theory to explain this Nano quantum behavior comes from the fact that the string theory, like quantum theory, recognizes both the particle and the wave nature of the Nano system.

Oral bone defects occur as a result of trauma, cancer, infections, periodontal diseases, and caries. Autogenic and allogenic grafts are the gold standard used to treat and regenerate damaged or defective bone segments. However, these materials do not possess the antimicrobial properties necessary to inhibit the invasion of the numerous deleterious pathogens present in the oral microbiota. In the present study poly(ε-caprolactone) (PCL), nano-hydroxyapatite (nHAp), and a commercial extract of Humulus lupulus L. (hops) were electrospun into polymeric matrices to assess their po-tential for drug delivery and bone regeneration. The fabricated matrices were analyzed by scanning electron microscopy (SEM), tensile analysis, thermogravimetric analysis (TGA), FT-IR assay, and in vitro hydrolytic degradation. The antimi-crobial properties were evaluated against the oral pathogens Streptococcus mutans, Porphyromonas gingivalis, and Aggregatibacter actinomycetemcomitans. The cytocompatibility was proved by the MTT assay. SEM analysis proved the nanostructured matrices have suitable fiber size. The present research provides new information about the interaction of natural compounds with ceramic and polymeric biomaterials. The hop extract and other natural or synthetic medicinal agents can be effectively loaded into PCL fibers and has the potential to be used in biomedical applications.

The goal of this article is to provide a review of the experimental techniques and procedures using vibration methods for the Structural Health Monitoring (SHM) of Polymer-Matrix Composites (PMC). It aims to be a guide for any researchers to carry out vibration experiments. The linear methods are first introduced. But as PMC is a complex material, these classic methods showed some limits, such as low accuracy for small damages, and a high environmental dependency. This is why the nonlinear methods are secondly studied, considering that the complexity of PMC induces a nonlinear behavior of the structure after damage occurrence. The different damage mechanisms are well explained in order to evaluate the potential of each vibration method to detect them.

In this study, sodium alginate (SA) was oxidized with potassium periodate to produce an alginate-based tanning agent. Using OSA as a biodegradable tanning agent and a nano-hydroxyapatite (nano-HAp) low concentration suspension to give flame retardancy to leather, eco-design concepts were applied to establish a chrome-, aldehyde-, and phenol-free tanning process. Micro-DSC, 1H NMR, attenuated total reflection mode Fourier transform infrared spectroscopy (FTIR-ATR), and scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS) were used to investigate the complex matrix collagen-OSA-nano-HAp. Micro-differential scanning calorimetry (micro-DSC) was used to assess OSA's ability to interact with collagen and stabilize the collagen-OSA matrix, while 1H unilateral nuclear magnetic resonance (NMR) was used to investigate the aqueous environment and limitations around collagen molecules caused by their association with OSA and nano-HAp. Industrial standard tests were used to assess mechanical properties and fire resistance of the new leather prototype. The findings reported here indicate that both OSA and nano-HAp are suitable alternatives for cleaner tanning technologies and more sustainable leather.

In recent years, frequent occurrences of low temperature disasters due to global climate change have significantly impacted the normal growth of crops. Research has indicated that inorganic selenium (which is more toxic) can not only enhance the effects of low temperature stress but also increase selenium content on plants; however, there is a scarcity of studies investigating the impacts of organic selenium and nano-selenium on crops. In order to investigate whether organic selenium and nano-selenium can enhance low-temperature tolerance and increase selenium content in pak choi (Brassica chinensis var. pekinensis. cv. ‘Suzhouqing’), different concentrations (0, 5, 10, 20 mg L-1) of exogenous selenium were applied in this experiment to assess their effects on plant growth, nutritional quality and antioxidant properties. RNA-Seq technology was used to sequence the transcriptome of the leaves. Based on the transcriptome data, a Weighted Gene Co-expression Network Analysis (WGCNA) was employed to construct a network that associates with physiological traits related to stress resistance. Two highly correlated gene co-expression modules were identified, and within them, nine hub genes associated with endocytosis, antioxidant stress, absorption, transport, and metabolism of selenium were discovered. The results indicated that the beneficial effects on yield and total selenium content under low temperature were attributed to (1) protection of photosynthetic pigments for enhancing photosynthetic capacity by the up-regulation of LHca2, LHcb1, LHca1, LHcb4 in KEGG pathway: photosynthesis-antenna proteins; (2) activation of antioxidant system for efficient ROS homeostasis such as SOD, POD and CAT by the genes such as Superoxide dismutase, Monodehydroascorbate and (3) selenium absorption by endocytosis, seleninum transportation by ABC transporter gene family and selenium metabolism related genes such as Cysteine synthase, Glutaredoxin. These findings provide a foundation for further investigation into the molecular mechanisms underlying the effects of organic selenium and nano-selenium on cyanochloride production at low temperatures.

The creation of nano-zero-valent iron (nZVI) by implementing plant extracts is an environmentally friendly process. High antioxidant capacity and phenol content indicated the possibility of oak-nZVI synthesis using oak leaf extract as a stable material with minimal agglomeration. Simultaneously removal of Cd and phosphates and Ni and phosphates was optimized by a statistically designed experiment with a definitive screening design. In terms of significance, 4 input parameters on process productivity were monitored: initial metal concentration (1 - 9 mgL-1), initial ion concentration (1- 9 mgL-1), pH value (2 - 10) and oak-nZVI dosage (2 - 16 ml). Phosphate removal efficiency, in the presence of cadmium, was the most influenced by oak-nZVI dose and cadmium concentration, while pH gave three statistically significant interactions with oak-nZVI dosage, cadmium concentration, and phosphate concentration. Phosphate removal efficiency, in the presence of Ni, is the most influenced by nickel concentration, phosphate concentration, pH, two-factor interaction between nZVI dose and Ni concentration, and quadratic phosphate interaction. The process optimization yielded the highest simultaneous removal efficiency of 98.99% and 87.30% for cadmium and phosphate ions, respectively. Also, the highest simultaneous removal efficiency of nickel and phosphates ion was 93.44% for 96.75%, respectively. The optimization process fits into the confidence intervals, confirming the assumption that the adopted regression model describes the process well. This work demonstrated an enormous potential and prosperous application for the Cd(II), Ni(II), and phosphate removal from water matrices.

Using analysis methods such as Rutherford backscattering Spectrometry, scanning electron microscopy, X-ray diffraction, and Raman spectroscopy, the diffusion behavior of iodine in micro/nano-porous graphite under high-temperature conditions was studied. The results indicate that iodine diffusion leads to the contraction of graphite microcrystals, a decrease in interlayer spacing, and an increase in defect density, resulting in a reduction in microcrystal size. Upon diffusion of iodine out of iodine-loaded graphite, the microcrystal size of the graphite increases, the interlayer spacing appears to return to the initial state, and the defect density decreases. By comparing the iodine diffusion performance of nanoporous graphite G400 and G450 with microporous graphite G500, it was determined that nanoporous graphite exhibits better inhibition of iodine diffusion compared to microporous graphite. Studying the diffusion behavior of iodine in micro/nano-porous graphite has significant academic significance and engineering value for the screening, design, and performance optimization of nuclear graphite.

Nitrile butadiene rubber (NBR) and its various composites are extensively studied as matrix materials for oil-free lubricated mechanical friction surfaces. While numerous macroscopic friction experiments can compare the frictional performance of different NBR composites, the complex material preparation and low experimental efficiency pose challenges. Nanoscale molecular dynamics (MD) simulations can help develop materials with improved friction properties, but they cannot directly provide the friction coefficients of actual macroscopic friction surfaces. Therefore, it is important to integrate the advantages of macroscopic and nanoscale friction studies and perform a synergistic analysis to modify the friction properties of composite materials. In this study, a multi-scale approach is proposed to simulate the frictional characteristics of carbon nanotube (CNT)-reinforced NBR by combining the MD friction simulation， micromechanical bridging model, and macroscopic finite element analysis (FEA) methods. The results of the multi-scale friction simulation of copper (Cu)-CNT/NBR composites show that the addition of CNTs significantly improves the frictional properties of NBR, and the extent of the improvement is related to the mass fraction of CNTs. As the mass fraction of CNTs increases (0%, 1.25%, 2.5%, 5%), the coefficient of friction decreases from 0.50 to 0.38. The results are validated by ring-block friction experiments at the same scale as the simulations.

In this work the effect of recycled concrete aggregate modified with mineral admixtures and Nano-silica on the mechanical properties and performance of the concrete was investigated after curing in tap water for 28 and 90 days. The compressive, ƒc, indirect tensile, ƒt, and flexural, ƒb, strengths for cured concrete specimens were measured and concrete strength ratios were analyzed. The water and rapid chloride permeability were measured. SEM analysis of microstructure was, also, investigated. The coarse aggregates used were dolomite (control) and recycled concrete aggregate with the incorporation of different mineral admixtures including ground granulated blast slag and granite as well as Nano-silica. It was found that, the slump values of the dolomite concrete decreases compared with recycle aggregate concrete. The results indicate that, the concrete mix containing recycle aggregate have the highest compressive strength, tensile strength and flexural strength compered to concrete mix containing dolomite aggregate. As far as the compressive strength is concerned, the addition 1 % NS and 15 % of slag improved the physico-mechanical properties of the recycled aggregate concretes compared to the other mixes after curing in tap water.

There is an international concern for reducing energy consumption and protecting environment by application of circular economy principles in the construction industry. The thermal resistance of concrete plays a significant role in the energy efficiency of a building, and this can be improved by using concrete products with high thermal resistance. This study analyzes the influence of perlite, as an addition, on the physico-mechanical properties of concrete, with the aim of identifying perlite concrete products that will respond to the improvement of the heat transfer resistance of the building envelope. The study examines the effect of replacing different amounts of concrete aggregates with perlite in percentages of 10%, 20%, 30% and 100%. The results show that the replacement of sand with perlite improves the thermal performance of concrete, but its mechanical properties are negatively affected. The research carried out highlighted that perlite can be successfully introduced in the production of concrete blocks used for external non-bearing walls pannels, the outstanding feature being the reduction of energy consumption in buildings. Overall, the paper identifies an efficient and environmentally friendly way of using perlite in the construction industry, improving the energy performance of buildings, and reducing the environmental impact of construction wastes.

There is a growing need for an area-wide knowledge of SOC contents in agricultural soils at field scale for food security, monitoring long-term changes related to soil health and climate change. In Germany, large-scale SOC maps are mostly available with a spatial resolution of 250 m to 1 km2. The nationwide availability of both digital elevation models at various spatial resolutions and multi-temporal satellite imagery enables the derivation of multi-scale terrain attributes and Landsat-based multi-temporal soil reflectance composites (SRC) as explanatory variables. On the example of an Bavarian test of about 8000 km2, the scale-specific dependencies between the representativeness of 220 soil samples and different aggregation levels of the explanatory variables were analyzed for their scale-specific predictive power. The aggregation levels were generated by applying a region-growing segmentation procedure, the SOC content prediction was realized by the Random Forest algorithm. In doing so, established approaches of (geographic) object-based image analysis (GEOBIA) and machine learning were combined. The modeling results revealed scale-specific differences. Compared to terrain attributes, the use of SRC parameters lead to a significant model improvement at large field-related scale levels. The joint use of both terrain attributes and SRC parameters resulted in further model improvements. The best modeling variant is characterized by an accuracy of R2=0.84 and RMSE=1.99.

The present decade has witnessed numerous investigations focussed on the determination of the mechanical properties of Fly ash composites. These composites have attracted attention, especially in the form of reinforcements owing to their excellent tensile and compressive properties coupled with impact and hardness response. A number of techniques viz. in-situ deposition, hand-up lay and compo-casting techniques have been reported to fabricate these composites. However, in the context of these composites, a systematic structure-property correlation has not been established till date. The present review is aimed at highlighting the current state of research in the avenue of Fly ash composites from two different viewpoints, viz. (i) fabrication technique and (ii) mechanical properties of the fabricated composites. Moreover, the necessity of establishing systematic structure-property correlation in these materials has also been briefly discussed from the author’s viewpoint.

Bone tissue engineering has been developed in the past decades, with the engineering of bone substitutes on the vanguard of this regenerative approach. PCL based scaffolds are fairly applied for bone regeneration, and several composites have been incorporated, as to improve the devices’ mechanical properties and tissue ingrowth. In this study, HA was incorporated on PCL based scaffolds with two different proportions, 80:20 and 60:40. Devices were produced with two different techniques, SC and MB, and further investigated with regards to their mechanical characteristics and in vitro cytocompatibility. Results show the MB devices to present more promising mechanical properties, along with the incorporation of HA. The latter is also related to an increase in osteogenic activity and promotion. Overall, this study suggest PCL:HA scaffolds to be promising candidates for bone tissue engineering, particularly when produced by the MB method.

The authors of this paper use an original method of diatomaceous earth fractionation, which allows for obtaining a filler with a specific particle size distribution. The method makes it possible to separate small, disintegrated and broken diatom frustules from those which maintained their original form in diatomaceous earth. The study covers a range of tests conducted to prove that such a separated diatomic fraction shows features different from the base diatomite used as an epoxy resin filler. We have examined mechanical properties of a series of diatomite/resin composites considering the weight fraction of diatoms and the parameters of the composite production process. The studied composites of Epidian 601 epoxy resin cross-linked with amine-based curing agent Z-1 contained 0 to 70% vol. of diatoms or diatomaceous earth. Samples were produced by casting into silicone moulds in vacuum degassing conditions and, alternatively, without degassing. The results have shown that the size and morphology of the filler based on diatomaceous earth affects mechanical and rheological properties of systems based on epoxy resin.

Tissue engineering and regenerative medicine has gradually evolved as a promising therapeutic strategy to the modern healthcare of the aging and diseased population. In this study, we developed a novel nano-fibrous scaffold and verified its application in the critical bone defect regeneration. The metformin-incorporated nano-gelatin/hydroxyapatite fibers (NGF) was produced by electrospinning, cross-linked, and then characterized by XRD and FTIR. Cytotoxicity, cells adhesion, cell differentiation, and quantitative osteogenic gene and protein expression were analyzed by bone marrow stem cells from rat. Rat forearm critical bone defect model was performed for the in vivo study. The nano-gelatin/hydroxyapatite fibers (NGF) were characterized by their porous structures with proper interconnectivity without significant cytotoxic effects; the adhesion of bone marrow stem cells on the nano-gelatin/hydroxyapatite fibers (NGF) could be enhanced. The osteogenic gene and protein expression were upregulated. Post implantation, the new regenerated bone in bone defect was well demonstrated in the NGF samples. We demonstrated that the metformin-incorporated nano-gelatin-hydroxyapatite fibers greatly improved healing potential on the critical sized bone defect. Although metformin-incorporated nano-gelatin/hydroxyapatite fibers had advantageous effectiveness during bone regeneration, further validation is required before it can be applied to clinical applications.

Phytophthora. infestans is a well known late blight causing oomycetes pathogen. It evolves and adapts to the host background and new fungicide molecules rapidly within a few years of their release, may be due to the predominance of transposable elements in its genome. Frequent and huge applications of fungicides cause environmental concerns. Here we developed target specific RNA interference based molecules, that are capable of effectively reducing the late blight infection. cDNA microarray expression data was used for the selection of genes involved in the early stage of infection process, sporulation etc. The in vitro synthesis of double stranded RNA molecule, targeting SDH, EF-1α, GPI-HAM344, PLD-3 and HSP-90 encoding genes revealed the reduction in growth, sporulation and symptom expression, which were subsequently assessed by culture bioassay, detached leaf assay and topical application methods. The multiple genes targeted dsRNA nano clay sprayed plants showed enhanced disease resistance (4% disease severity) and least sporulation (<1x103), compared to naked dsRNA spray. Use of nano clay was assumed to be involved in the effective delivery, protection and boosting the action of RNAi in potato plants. A significant difference in the growth, sporulation count, disease severity and reduced expression of the genes and confocal microscopy imaging authenticates the effects of SIGS on late blight disease progression. Our research demonstrated that topical dsRNA nano clay spray under the open-air environment could be an alternative to chemical fungicides and transgenic approaches as a novel plant protection strategy for late blight in an environmentally friendly manner.

As the field of nanoscience is rapidly evolving, interest for novel, upgraded nanomaterials with combinatory features is also inevitably increasing. Hybrid composites, offer simple, budget-conscious and environmental-friendly solutions that can cater multiple needs at the same time and be applicable in many nanotechnology-related and interdisciplinary studies. The physicochemical idiocrasies of dendritic polymers have inspired their implementation as sorbents, active ingredient carriers and templates for complex composites. Ceramics are distinguished for their mechanical superiority and absorption potential that render them ideal substrates for separation and catalysis technologies. The integration of dendritic compounds to these inorganic hosts can be achieved through chemical attachment of the organic moiety onto functionalized surfaces, impregnation and absorption inside the pores, conventional sol-gel reactions or via biomimetic mediation of dendritic matrices, inducing the formation of usually spherical hybrid nanoparticles. Alternatively, dendritic polymers can propagate from ceramic scaffolds. All these variants are covered in detail. Optimization techniques as well as established and prospected applications are also presented.

The use of cow bones for biomaterial is still limited; accordingly, the cow bones waste has low economic value. Basically, a human’s and a cow’s bones are the same in terms of their forming compound. Aluminum (Al) has the potential to combine with hydroxyapatite (HAp) to make metal matrix composites (MMC) that have the potential for biomaterials. Compatible elements to be combined with Al and HAp are magnesium (Mg), titanium (Ti), and Copper (Cu), used self-high propagating temperatures synthesis (SHS). MMC can be processed to be a useful, solid product. Applying pressure to the SHS reaction and heating process may result in biomaterial composite product consisting of some matrix materials such as Al come from cans materials used in the experiment was HAp that was processed from cow bones calcination, added by can that contained aluminum and wetting agent, namely magnesium. The exothermic temperature was 800-900°C. The compaction process was done to allow materials to be bound. Based on the ASTM F138 standard for element of biomaterials, the porosity value was below 30% and hardness level above 40 HV. Cow bones and can-based composite sample with the composition of HAp-Al-Mg: 85%-10%-5% met the standard since the hardness value was: 73.3 HV with a porosity value of 29.88%.

Currently, metal nanoparticles have varied uses for different medical, pharmaceutical, and agricultural applications. Nano-biotechnology combined with green chemistry has great potential for the development of novel and necessary products that benefit human activities, while encourages the reduction of hazardous reagents for nanoparticle production. Green chemistry has an important role due to its contribution to unconventional synthesis methods of gold and silver nanoparticles from plant extracts, which have exhibited antimicrobial potential among other outstanding properties. Biodiversity-rich countries need to collect and convert knowledge from biological resources into processes, compounds, methods, and tools, which need to be achieved along with sustainable use and exploitation of biological diversity. Therefore, this review focuses on the importance of metal nanoparticles, the use of plant extract for their synthesis as well as other available methods, and the relevant antimicrobial activity that can be exploited in a sustainable model of agricultural management through a modern nanotechnological approach.

Hot deformation at elevated temperature is essential to densify the particle reinforced Aluminum matrix composites (AMCs) and improve their performance. However, hot deformation behavior of the AMCs is sensitive to the variation of hot processing parameters. In this paper, optimal processing parameters of the dual-scale SiCp/A356 composites was determined to explore the control strategy of the microstructure. Hot compression tests were conducted at the temperature ranging from 460 to 520℃ under strain rates from 0.01 to 5 s−1. Constitutive equation and processing maps were presented to determine the hot processing parameters. Microstructure evolution of the dual-scale SiCp/A356 composites was analyzed. The strain rate of 0.62 ~ 5s-1 and deformation temperature of 495 ~ 518℃ is suitable for the hot processing. The number of DRX grains in the “safe” domains is larger and the dislocation density is lower compared to those of instability domains. DRX particles mainly occurred around SiC particles. The presence of SiC particles can promote effectively the DRX nucleation, which result in that the dynamic softening mechanism of the dual-scale SiCp/A356 composites is dominated DRX.

Porosity in plasma sprayed coatings is vital for most engineering applications. It is either advantageous or disadvantageous depending on the functionality of the coating and the immediate working environment. Consequently, the formation mechanisms and development of porosity has been extensively explored to find out modes of controlling porosity in plasma sprayed coatings. In this work, a comprehensive review of porosity on plasma sprayed coatings is established. The formation and development of porosity on plasma sprayed coatings are governed by set spraying parameters. Optimized set spraying parameters have been used to achieve the most favorable coatings with minimum defects. Even with the optimized set spraying parameters, defects like porosity still occur. Here, we discuss other ways that can be used to control porosity in plasma sprayed coating with emphasis to atmospheric plasma sprayed chromium oxide coatings. Techniques like multi-layer coatings, nano-structured coatings, doping with rare earth elements, laser surface re-melting and a combination of the above methods have been suggested in adjusting porosity. The influences of porosity on properties of plasma sprayed coatings and the measurement methods of porosity have also been reviewed.

Traditional silicon binary circuits continue to face challenges such as high leakage power dissipation and large area of interconnections. Multiple-Valued Logic (MVL) and nano-devices are two feasible solutions to overcome these problems. In this paper, we present a novel method to design ternary logic circuits based on Carbon Nanotube Field Effect Transistors (CNFETs). The proposed designs use the unique properties of CNFETs, e.g., adjusting the Carbon Nanotube (CNT) diameters to have the desired threshold voltage and have the same mobility of P-FET and N-FET transistors. Each of our designed logic circuits implements a logic function and its complementary via a control signal. Also, these circuits have a high impedance state which saves power while the circuits are not in use. We show a more detailed application of our approach by designing a two-digit adder-subtractor circuit. We simulate the proposed ternary circuits using HSPICE via standard 32nm CNFET technology. The simulation results indicate the correct operation of the designs under different process, voltage and temperature (PVT) variations. Moreover, we designed a two-digit adder/subtractor and a power efficient ternary logic ALU based on the proposed gates. Simulation results show that the two-digit adder/subtractor using our proposed gates has 12X and 5X lower power consumption and PDP (power delay product) respectively, compared to previous designs.

Metal and alloy toughening was the core and long-term research direction in materials filed. As grain size had bimodal distribution, micro/nano-structured alloys presented excellent comprehensive mechanical properties, and this had become one of the research hotspots and developing trends in the field of nanotechnology. In-situ tensile test was a direct and effective method to study the deformation mechanism of materials, which revealed the multiple mechanisms responding to feature grain sizes and provided reliable experimental means and research technique. Research on development of in-situ technique and its applications in mechanical properties was reviewed in this paper according to the recent advances on the modern mechanical properties for high strength and high plasticity alloy at home and abroad. The disadvantages of the present study of preparation methods and investigation techniques for high-performance alloy had been concluded. Finally, the development prospects of high strength and high plasticity alloy materials were analyzed.

Due to the difficult metallurgical conditions during production, advanced processing techniques are required to produce functionally graded metal matrix composites. In this study, we explored a novel approach by using a combination of two different methods to produce Functionally Graded 7075 Al / SiCp composites. First process was direct semi-solid stirring that was used to prevent particle agglomeration, brittle reaction products, floating or settling of the reinforcements and poor wettability for the production of SiCp (wt. 5-20%) reinforced aluminum matrix composites. In the direct semi-solid mixing process, the matrix material remains in a semi-solid state until the reinforcement addition process is completed. The second novel process was sequential squeeze casting to provide liquid diffusion between two composite layers that were used to produce functionally graded aluminum matrix composite. The microstructure and interlayer zones were characterized by using optical microscopy and scanning electron microscopy. The resulting functionally graded material was subjected to spectrometer analyses, density measurements, and metallographic examinations in order to determine the characteristics of its layers and interfacial zones, as well as to assess the formation of the graded structure. The results obtained from this research provide the potential to use this new combined manufacturing method, which is relatively inexpensive, efficient and easily applicable, in order to produce functionally graded SiCp reinforced aluminum composites.

This comprehensive review explores recent advancements in heavy metal remediation techniques, focusing on the utilization of cellulose-silica composites and tailored surface modification techniques. We examine the synthesis strategies and properties of cellulose-silica adsorbents, highlighting their enhanced adsorption capacities and structural robustness for removing heavy metal pollutants from aqueous environments. The review investigates various surface modification approaches, including thiol-functionalization, amino acid grafting, and silane coupling agents, for optimizing the surface chemistry and morphology of cellulose-silica composites. Mechanistic insights into the adsorption processes and kinetics of modified adsorbents are discussed, along with considerations for optimizing adsorption performance under different environmental conditions. This review provides valuable perspectives on the development of effective adsorbent materials for sustainable heavy metal remediation applications.

With the increasing demand for energy worldwide, researchers from different fields have been striving to improve the sustainability and proper utilization of energy resources. Passive radiative cooling, as a natural energy transport method, can achieve cooling without additional external energy input. This review provides a comprehensive examination of passive radiative cooling, including its fundamental theories and latest development. A particular emphasis is placed on the diverse range of fields where passive radiative cooling has been applied, notably including but not limited to construction and architecture. The current state of applications, potential challenges that may arise with wider adaption and promising research directions for each field are thoroughly discussed. This review underscores the universal applicability and feasibility of passive radiative cooling and contributes to its future development by identifying promising areas for further exploration.

Thermoplastic composites are continuously replacing thermosetting composites in lightweight structures. However, the accomplished work on the fatigue behavior of thermoplastics is quite limited. In the present work, we propose a numerical modeling approach for simulating fatigue delamination growth and predicting the residual tensile strength of quasi-isotropic TC 1225 LM PAEK thermoplastic coupons. The approach is supported and validated by tension and fatigue (non-interrupted and interrupted) tests. Fatigue delamination growth is simulated using a mixed-mode fatigue crack growth model, which is based on the cohesive zone modeling method. All interfaces between the thermoplastic plies were modelled using cohesive elements. Quasi-static tension analyses on pristine and fatigued coupons were performed using a progressive damage model implementing a set of Hashin-type strain-based failure criteria and a damage mechanics-based material property degradation module. Using the fatigue model, delamination growth was predicted as a function of number of cycles at all interfaces. The results agree well with C-scan images taken on fatigued coupons during interruptions of fatigue tests. An unequal and unsymmetric delamination growth was predicted due to the quasi-isotropic lay-up. Moreover, the combined models capture the decrease in the residual tensile strength of the coupons. In the quasi-static tension analysis of the fatigued coupons, the driving failure mechanisms are the fast propagation of the pre-existing delamination and the severe matrix cracking.

An effective approach to fabricate large-scale of conducting polyaniline (PANI) by an in situ anodic electrochemical polymerization on the nickel foam, which coated by a novel aryl diazonium salt (ADS)-functionalized graphene (ADS-G). In present work, ADS-G was used as a high surface area support material for electrochemical polymerization of PANI. Electrochemical performances of the ADS-G/PANI composites exhibited better suitability as supercapacitor electrode materials than that of the PANI. The ADS-G/PANI composites achieved the specific capacitance of 528 F g-1, which was higher than that of PANI (266 F g-1) due to the excellent electrode-electrolyte interaction and synergistic effect of electrical conductivity between ADS-G and PANI in the composites. These findings suggested that the ADS-G/PANI composites were a suitable composite for the potential supercapacitor applications.

Complex-structured polymeric microparticles hold significant promise as advance in next-generation medicine mostly due to demand from developing targeted drug delivery. However, the conventional methods for producing these microparticles of defined size, shape and sophisticated composition often face challenges in scalability, reliance on specialized components such as micro-patterned templates, or have limited control over particle size distribution and cargo release kinetics. In this study, we introduce a novel and reliably scalable approach for manufacturing microparticles of defined structures and sizes with variable parameters. The concept behind this method involves the deposition of a specific number of polymer layers on a substrate with low surface energy. Each layer can serve as either the carrier for cargo or a programmable shell-former with predefined permeability. Subsequently, this layered structure is precisely cut into desired-sized blanks using a laser. The manufacturing process is completed by applying of heat to the substrate what results on sealing the edges of the blanks. The combination of the high surface tension of the molten polymer and the low surface energy of the substrate enables the formation of discrete particles, each possessing semi-spherical or other designed geometries determined by their internal composition. Such anisotropic microparticles are envisaged versatile applications.

This study investigates the contribution of nano-alumina (nA: 1-3wt.% binder) to the performance of silica fume (SF-10%) blended mortar in ternary blended mortar. The fresh (workability, setting time) and hardened properties (compressive strength and thermal resistance (300 °C for 1 h)), were examined. Nano alumina (nA) contributed positively to the consistency of SF blended mortar such that similar workability could be achieved with OPC when 3% nA was added. The initial and final setting time of 180 and 220 mins were recorded in SF blended mortar and reduced by 18.4 and 21.8%, respectively by adding 3%nA. The optimum mixture that contained 10%SF and 2%nA had 3-d and 28-d compressive strengths of 28 and 43.2 MPa. In the absence of nA, this reduced by 14.3% and 29.4% while it reduced by 25.2% and 16.7%, respectively in OPC mortar. The main products characterizing SF-nA ternary blended binder with dense microstructural density were nepheline and tobermorite. Besides, it is more susceptible to carbonation despite its superior performance in thermal resistance when compared to SF blended and OPC mortars.

With a view to sustainable development and circular economy, this work focused on the possibility to valorize a secondary waste stream of recycled carbon fiber (rCF) to produce a 3D printing usable material with PA6,6 polymer matrix. The reinforcing fibers implemented in the present research are the result of a double recovery action: starting with pyrolysis from which long fibers are obtained, used to produce non-woven fabrics and, subsequently, fiber agglomerate wastes obtained from this last process are ground in a ball mill. The effect of a different amount of reinforcement at 5% and 10% by weight on the mechanical properties of 3D printed thermoplastic composites was investigated. Although the recycled fraction was successfully integrated in the production of filaments for 3D printing and therefore in the production of specimens via Fused Deposition Modeling technique, the results showed that fibers did not improve the mechanical properties as expected, due to an unsuitable average size distribution and the presence of a predominant dusty fraction ascribed to the non-optimized ball milling process. PA6,6 + 10 wt.% rCF composites exhibited a tensile strength of 59.53 MPa and a tensile modulus of 2.24 GPa, which correspond to an improvement in mechanical behavior of 21 5 % and 5 21 % compared to the neat PA6,6 specimens, respectively. The printed composite specimens loaded with the lowest content of rCF provided the greatest improvement in strength (+ 9% over the neat sample). Then, a prediction of the “optimum” critical length of carbon fibers was proposed that could be used for future optimizations of the recycled fiber processing.

In this study various samples were fabricated by increasing the amount of CNT from 0% to 5%. The bulk mechanical properties of the samples were measured using DMA. Alternatively, the local mechanical properties were assessed using nanoindentation technique. There is a clear trend that the behavior of the material is dependent of carbon fillers before, during and after percolation threshold. The bulk mechanical properties were reduced after the percolation threshold due to CNT agglomeration. Then the samples were exposed to acid solution for one week and one month. Regardless the amount of CNT in the matrix, there is always a gradient of properties from the skin to the core of the sample. There is a net reduction of in physical properties. However, the level of degradation was a dependent of the amount of CNT in the host polymer. At higher concentration the CNTs behave as a barrier. However due to the formation of porosity around the CNT agglomerates, the acid diffusion encounters preferential path ways. . Both techniques lead to the same observation..

Polyhedral oligomeric silsesquioxane (POSS) is a suitable nanoscale reinforcement for thermosetting polymers, such as epoxy resin systems in order to modify its mechanical, thermal, and chemical properties. The inclusion of POSS in the epoxy resin at higher loading (greater than 1 wt.%), however, introduces the ductility during the fracture behavior of these nanocomposites. Consequently, the J-integral is used to quantify the fracture behavior of these materials and characterize the crack growth resistance curve against stable crack growth. A range of nanocomposites is prepared by adding 0.5, 1, 3, 5, and 8 wt.% of glycidyl POSS into DGEBF epoxy resin cured with an amine-based curing agent. From the fracture toughness experiment the load-displacement result confirms that when the POSS reinforcement is greater than 1 wt.%, the fracture behavior of the nanocomposite changes from brittle to ductile. For both brittle and ductile nanocomposites, the addition of POSS molecules improves the crack initiation toughness. The development of POSS–POSS compliant domains are reported previously, is attributed for this change in the failure behavior. The fractured images of POSS–epoxy nanocomposites, obtained using scanning electron microscopy, show that the increase in fracture resistance at higher values of POSS loading occurs due to the extensive shear yielding. Meanwhile, the increased fracture toughness at lower values of POSS loading occurs due to crack pinning and crack deflection.

Lead-free ferroelectric perovskite N-methyl-N'-diazabicyclo[2.2.2]octonium)–ammonium triio-dide, MDABCO-NH₄I₃, nanocrystals are embedded in three different polymer fibers fabricated by the electrospinning technique. The nanofibers, which are very flexible and have a high Young modulus, behave as active piezoelectric energy harvesting sources that produce a piezoelectric voltage coefficient up to geff = 3.6 VmN-1 and show a blue intense luminescence band at 325 nm. In this work, the pyroelectric coefficient is reported for the MDABCO-NH₄I₃ perovskite inserted in electrospun fibers. At the ferroelectric-paraelectric phase transition, the embedded nanocrystals display a pyroelectric coefficient as high as 194×10-6 Cm-2k-1, within the same order of magnitude as that reported for the state-of-the-art bulk ferroelectric triglycine sulfate (TGS). The perovskite nanocrystals embedded into the polymer fibers remain stable, and no degradation is caused by oxidation.

The interfacial interface between the fibers and the matrix plays a key role for epoxy matrix composites and short recycled randomly arranged fibres. This study used short recycled carbon fiber (RCF) as a filler. Plasma treatment was used for carbon fiber surface treatment. This treat-ment was performed using radio (RF) and microwave (MW) frequencies at the same pressure and atmosphere. Appropriate chemical modification of the fiber surfaces helps to improve the wettability of the carbon fibers and, at the same time, allows the necessary covalent bonds to form between the fibers and the epoxy matrix. The effect of the plasma treatment was analyzed and confirmed by XPS analysis, Raman microscopy, SEM, TEM and wettability measurements. Composite samples filled with recycled carbon fibers with low concentrations (1 wt%, 2.5 wt% and 5 wt%) and high concentrations (20 wt% and 30 wt%) were made from selected treated fi-bers. The mechanical properties (impact toughness, 3PB) were analyzed on these samples. It was found that the modulus of elasticity and bending stress increase with the increasing content of recycled carbon fibers. A more significant change in impact strength occurred in samples with low concentration.

This paper describes the packaging models that are fundamental for the design of ultra-high-performance concrete (UHPC), and their evolution. They are divided into two large groups: continuous and discrete models. The latter are those that provide the best answer in obtaining an adequate simulation of the packing of the particles up to nanometric size. This includes the interaction among the particles by means of loosening and wall coefficients, allowing a simulation of the virtual and real compactness of such particles. In addition, a relationship between virtual and real compactness is obtained, through the compaction index, which may simulate the energy of compaction that the particles undergo in their placement in the mold. The use of last-generation additives allows such models to be implemented with water-cement (w/c) ratios close to 0.18. However, the premise of maximum packing as a basic pillar for the production of UHPC should not be the only one. The cement hydration process affected by nanoadditions and the ensuing effectiveness in the properties in both fresh and hardened state according to the respective percentages in the mixture should also be studied. An adequate ratio and proportion of these additions may lead to an obtaining of better results even with lower levels of compactness.

Recently, significant events took place that added immensely to the sociotechnical pressure for developing sustainable composite recycling solutions, namely (1) a ban on composite landfilling in Germany in 2009, (2) the first major wave of composite wind turbines reaching their End-of-Life (EoL) and being decommissioned in 2019-2020, (3) the acceleration of aircraft decommissioning due to the COVID-19 pandemic, and (4) the increase of composites in mass production cars, thanks to the development of high volume technologies based on thermoplastic composites. Such sociotechnical pressure will only grow in the upcoming decade of 2020s as other countries are to follow Germany by limiting and banning landfill options, and by the ever-growing number of expired composites EoL waste. The recycling of composite materials will therefore play an important role in the future, in particular for the wind energy, but also for aerospace, automotive, construction and marine sectors to reduce environmental impacts and to meet the demand. The scope of this manuscript is a clear and condensed yet full state-of-the-art overview of the available composite recycling technologies of both low and high Technology Readiness Levels (TRL). TRL is a framework that has been used in many variations across industries to provide a measurement of technology maturity from idea generation (basic principles) to commercialization. In other words, this work should be treated as a technology review providing guidelines for the sustainable development of the industry that will benefit the society. The authors propose that one of the key aspects for the development of sustainable recycling technology is to identify the optimal recycling methods for different types of composites. Why is that the case can be answered with a simple price comparison of E-glass fibers (~2 $/kg) versus a typical carbon fiber on the market (~20 $/kg) – which of the two is more valuable to recover? However, the answer is more complicated than that – the glass fiber constitutes about 90% of the modern reinforcement market, and it is clear that different technologies are needed. Therefore, this work aims to provide clear guidelines for economically and environmentally sustainable End-of-Life (EoL) solutions and development of the composite material recycling.

At present, the world is now passing a very far different time than normal situation due to the COVID-19 pandemic crisis. The global life-style and human civilization is currently progressing with down-stream that affecting almost every sectors necessary for human civilizations except the current environmental situation. To control the COVID-19 spreading, most of the countries are following lockdown process that reduces human mobility, thus reducing the CO2 emission to the environment. Though the COVID-19 pandemic is a blessing for the present environment, however, the post-COVID world will face a massive thrust of energy and only conventional energy resources may not be enough to mitigate the energy demands. Solar power generation technology mainly the photovoltaic (PV) systems and their advancement can be the leading possibilities to minimize the gap between the power demand and generation. It is now time to think how we can improve the PV power generation in future and the post-COVID world. In this encyclopaedia communication, we report on Nano-technological approach to improve the conversion efficiency of GaAs solar cells. We have designed and optimized several types of nano-structured assemblies that can be implemented to reduce the front surface incident light reflection losses thus can assist to improve the conversion efficiency of GaAs solar cells.

The extrusion-based additive manufacturing is a popular fabrication method, which has attracted the attention of various industries due to its simplicity, cheapness, ability to produce complex geometric shapes, and high production speed. One of the effective parameters in this process is the feed of filament that is presented in the production G-code. The feed of filament is calculated according to the layer height, the extrusion width and the length of printing path. All the required motion paths and filling patterns created by commercial software are a set of straight lines or circular arcs that are placed next to each other at a fixed distance. In special curved paths, the distance of adjacent ones is not equal at different points, and due to the weakness of common commercial software, it is not possible to create curved paths for proper printing. Therefore, making a special computer code that can be used to create various functions of curved paths is investigated in this research, and also the feed of filament parameter is studied in detail. Next, by introducing a correction technique, the feed of filament is changed during the curved path to distribute the polymer material uniformly. Finally, composite samples (which have variable stiffness) consisting of curved fibers are produced with the proposed method, and the high quality of printed samples confirm the suggested code and technique.

The loss of integrity and adverse effect on mechanical properties can be concluded as attributing miro/macro-mechanics damage in structures, especially in composite structures. Damage as a progressive degradation of material continuity in engineering predictions for any aspects of initiation and propagation requires to be identified by a trustworthy mechanism to guarantee the safety of structures. Besides the materials design, structural integrity and health are usually prone to be monitored clearly. One of the most powerful methods for the detection of damage is machine learning (ML). This paper presents the state of the art of ML methods and their applications in structural damage and prediction. Popular ML methods are identified and the performance and future trends are discussed.

The science on the anthropogenic airborne aerosols impacting upon the World Heritage marble monument, the Taj Mahal, at Agra has been studied in the light of modern physico-chemical approaches. The study is an effort to understand yet unrecognized airborne species which were found on the surface of the Taj Mahal monument. These species have been analyzed in the light of current analytical methods to impart characterization features and their possible impacts on the surface of the marble. Chemical constituents of these substrates which were incorporated over the top surface of the monument have been identified. Interestingly, the carbon particulates which were thought in the micro level, popularly called “particulate matters” has now been identified even in the nano domain entity, which are chemically more reactive, have been found on the surface of the monument. Because of their high chemical activity these nano carbons do play newer chemistry in the presence of air and sunlight generating several reactive oxygen species (ROS).These ROS are capable to respond to complicated chemical reactions on the surface of the marble in association with deposited cyanophyceae and other deposits of plant origin causing rapid degradation. This study provides the nature of onslaught borne out by such monument exposed under the prevalent smoggy environmental scenario.

The effect of γ-ray irradiation on surface plasmon resonance (SPR) sensing capability of refractive index (n = 1.418–1.448) of the silica glass optical fiber comprised of germano-silicate glass cladding embedded with Au nano-particles (NPs) was investigated. As the γ-ray irradiation increased from 1 hour to 3 hours with the dose rate of 1,190 Gy/h, the morphology of the Au NPs and the SPR spectrum were found to change. The average diameter of Au NPs increased with the aspect ratio from 1 to 2 and the nano-particles became grown to the clusters. The SPR peak wavelength shifted towards longer wavelength with the increase of total dose of γ-ray irradiation regardless of the corresponding refractive indices. The SPR sensitivities (wavelength/refractive index unit, nm/RIU) also increased from 407 nm/RIU to 3,553 nm/RIU, 1,483 nm/RIU, and 2,335 nm/RIU after the γ-ray irradiation at the total dose of 1,190 Gy, 2,380 Gy, and 3,570 Gy, respectively.

Hydroiodic acid (HI) treated - reduced graphene oxide (rGO) ink/conductive polymeric composites are considered as promising cold cathodes in terms of high geometrical aspect ratio and low field emission (FE) threshold devices. In this study, four simple, cost-effective, solution-processed approaches for rGO-based field effect emitters were developed, optimized and compared; rGO layers were coated on a) n+ doped Si substrate, b) n⁺-Si/P3HT:rGO, c) n⁺-Si/PCDTBT:rGO and d) n⁺-Si/PCDTBT:PC₇₁BM:rGO composites, respectively. The fabricated emitters were optimized by tailoring the concentration ratios of their preparation and field emission characteristics. In a critical composite ratio, FE performance was remarkably improved compared to the pristine Si, as well as n⁺-Si/rGO field emitter. In this context, the impact of various materials, such as polymers, fullerene derivatives, as well as different solvents on rGO function reinforcement and consequently on FE performance upon rGO-based composites preparation was investigated. The field emitter consisted of n⁺-Si/PCDTBT:PC₇₁BM(80%):rGO(20%)/rGO displayed a field enhancement factor of ∼2850, with remarkable stability over 20h and low turn-on field in 0.6V/μm. High-efficiency graphene-based FE devices realization paves the way towards low-cost, large-scale electron sources development. Finally, the contribution of this hierarchical, composite film morphology was evaluated and discussed.

The effect of hybrid carbon fillers of multi-walled carbon nanotubes (CNT) and carbon black (CB) on the electrical and morphological properties of polystyrene (PS) nanocomposites were systematically investigated in microinjection molding (μIM). The polymer nanocomposites with three different filler concentrations (i.e. 3, 5 and 10 wt%) at various weight ratios of CNT/CB (100/0, 30/70, 50/50, 70/30, 0/100) were prepared by melt blending, then followed by μIM under a defined set of processing conditions. A rectangular mold insert which has three consecutive zones with decreasing thickness along the flow direction was adopted to study abrupt changes in mold geometry on the properties of resultant microparts. The distribution of carbon fillers within microparts was observed by scanning electron microscope, which was correlated with electrical conductivity measurements. Results indicated that there is a flow-induced orientation of incorporated carbon fillers and this orientation increased with increasing shearing effect along the flow direction. High structure CB is found to be more effective than CNT in terms of enhancing the electrical conductivity, which was attributed to the good dispersion of CB in PS and their ability to form conductive networks via self-assembly. Morphology observations indicated that there is a shear-induced depletion of CB particles in the shear layer, which is due to the marked difference of shear rates between the shear and core layers of the molded microparts. Moreover, an annealing treatment is beneficial to enhance the electrical conductivity of CNT-containing microparts.

To improve the interfacial bonding of sisal fiber reinforced polylactide biocomposites, polylactide (PLA) and sisal fibers (SF) were melt-blended to fabricate bio-based composites via in situ reactive interfacial compatibilization with the addition of an epoxy-functionalized oligomer (ADR). The FTIR analysis and SEM characterization demonstrated that PLA molecular chain was bonded to the fiber surface and epoxy-functionalized oligomer played a hinge-like role between sisal fibers and PLA matrix, which resulted in improved interfacial adhesion between fibers and PLA matrix. The interfacial reaction and microstructures of composites were further investigated by thermal and rheological analyses, which indicated that the mobility of the PLA molecular chain in composites was restricted because of the introduction of ADR oligomer, which in turn reflected the improved interfacial interaction between SF and PLA matrix. These conclusions were further investigated by the calculated activation energies of glass transition relaxation (△Ea) of composites via dynamic mechanical analysis. The mechanical properties of PLA/SF composites were simultaneously reinforced and toughened via addition of ADR oligomer. The interfacial interaction and structure-properties relationship of composites are key points of this study.

Biocompatible polymeric materials with potential to form functional structures in association with different therapeutic molecules have a high potential for biological, medical and pharmaceutical applications. Therefore, the protective capability of the inclusion nano-Complex formed between the sodium salt of poly(maleic acid-alt-octadecene) and a β-lactam drug (ampicillin trihydrate) on the chemical, enzymatic and biological degradation was evaluated. PAM-18Na was produced and characterized as reported previously. The formation of polymeric hydrophobic aggregates in aqueous solution was determined, using pyrene as a fluorescent probe. Furthermore, the formation of polymer-drug nano-complexes was characterized by Differential Scanning Calorimetry-DSC, viscometric, ultrafiltration/centrifugation assays, zeta potential and size measurements by dynamic light scattering-DLS. The PAM-18Na capacity to avoid the chemical degradation was studied through stress stability tests. The enzymatic degradation was evaluated from a pure β-lactamase, while the biological degradation was determined by different β-lactamase producing Staphylococcus aureus strains. When ampicillin was associated with PAM-18Na, the half-life time in acidic conditions increased, whereas both the enzymatic degradation and the minimum inhibitory concentration decreased to a 90 and 75%, respectively. These results suggest a promissory capability of this polymer to protect the β-lactam drugs against chemical, enzymatic and biological degradation.

The detection of dopamine in a highly sensitive and selective manner is crucial for the early diagnosis of a number of neurological diseases/disorders. Here, a report on a new platform for the electrochemical detection of dopamine with a considerable accuracy that comprises a 3D porous graphene oxide (pGO)/gold nanoparticle (GNP)/pGO composite-modified indium tin oxide (ITO) is presented. The pGO was first synthesized and purified by ultrasonication and centrifugation, and it was then further functionalized on the surface of a GNP-immobilized ITO electrode. Remarkably, owing to the synergistic effects of the pGO and GNPs, the 3D pGO-GNP-pGO-modified ITO electrode showed a superior dopamine-detection performance compared with the other pGO- or GNP-modified ITO electrodes. The linear range of the newly developed sensing platform is from 0.1 μM to 30 μM with a limit of detection (LOD) of 1.28 μM, which is more precise than the other previously reported GO-functionalized electrodes. Moreover, the 3D pGO-GNP-pGO-modified ITO electrodes maintained their detection capability even in the presence of several interfering molecules (e.g., ascorbic acid, glucose). The proposed platform of the 3D pGO-GNP-pGO-modified ITO electrode could therefore serve as a competent candidate for the development of a dopamine-sensing platform that is potentially applicable for the early diagnosis of various neurological diseases/disorders.

The sound and heat insulation are among the most important concerns in modern life and nonwoven composite structures are highly effective in noise reduction and heat insulation. In this study, three layered nonwoven composite structures composed of recycled polyester (r-Pet) based thermo bonded nonwoven outer layer and meltblown nonwovens from PP and PBT as inner layers were formed to provide heat and sound insulation. Fiber fineness and cross section of thermo bonded outer layer, fiber type (PP/PBT), areal weight (100/200g/m2) and process conditions (calendared/non-calendared) of meltblown inner layer have changed systematically and the influence of these parameters on thickness, bulk density, air permeability, sound absorption coefficient and thermal resistance of composite structures were analyzed statistically. Also; the results were compared with composite structures including electrospun nano fiber web inner layer and with structures without inner layer. It was determined that sound absorption coefficients ranging between 0.77-0.98 for moderate sound frequencies and 0.99-1 for higher sound frequencies were acquired with developed nonwoven composite structures. Besides, higher sound absorption coefficients were obtained as 0.71 and 0.74 for low sound frequencies such as 800 and 1000Hz, respectively. As a result of this study it can be concluded that developed nonwoven composite structures that provides better sound absorption coefficients and similar thermal conductivity values compared to previous studies and materials in the market can be used as insulation material in required areas.

Development of load-bearing polymer composite constructions in civil engineering, such as industrial chimneys and gas ducts, requires filling some research gaps. These gaps are related to long-term behavior under mechanical and temperature loads, cyclic ones as well. Such conditions mean that viscoelasticity should be considered. First of all, viscoelastic parameters should be calculated, based on the used inner structure model. Then, due to the high working temperatures, thermal aging should be considered as well. This research is devoted to effects of thermal aging on viscoelastic behavior of polymers. Two sets of experiments were conducted: creep tensile tests and cyclic heating in constrained state. The Kelvin-Voigt viscoelasticity model was used to determine the rheological parameters of binder from experimental creep curves. Thermally-aged binder turned out to lose its viscous properties and became elastic. Cyclic heating was used to compare the behavior of normal and thermally-aged binder and to evaluate the possibility of temperature stress accumulation. Similar to creep tests, cyclic heating showed that aged binder lost viscosity and worked almost perfectly elastic. Non-aged binder was prone to stress accumulation much more. As a result, the rheological behavior of aged and non-aged binder was compared and showed a significant difference. In addition, the influence of temperature stress accumulation on stress—strain state was evaluated and turned out to be significant as well. The obtained results can be further used to predict the mechanical behavior of structures made of polymer composites operating for a long time at elevated temperatures, including those exceeding the glass transition temperature.

Optimizing input parameters not only improves production efficiency and processing quality but also plays a crucial role in the development of green manufacturing engineering practices. The aim of the present study is to conduct a comparative evaluation at cutting performance and machinability process during the turning of AISI 4340 steel under different cooling conditions. The study analyses cutting operations during turning using dry, minimum quantity lubrication (MQL), and nano-MQL. As control parameters in the experiments, three different cooling types, cutting speed (100, 150, 200 m/min), and feed rate (0.1, 0.15, 0.20 mm/rev) levels were applied. The experiment results present that the optimal output values are found as Vb=0.15 mm, Ra=0.81µm, 88.1 dB for sound intensity, and I=4.18 A for current. Moreover, variance analysis (ANOVA) was performed to determine the effects of input parameters on response values. Under dry, MQL, and nano-MQL processing conditions, parameters affecting tool wear, surface roughness, current by the motor shaft, and sound level were examined in detail, along with the chip morphology. The responses obtained were optimized according to the Taguchi S/N method. As a result of optimization, it was concluded that the optimum values for cutting conditions (A3B1C1) were nano-MQL cooling and V=100 m/min, f=0.1 mm/rev cutting. Last but not least, it was observed that there was a 13% improvement in tool wear, 7% in current, 9% in surface roughness, and 8% in sound intensity compared to the standard conditions. In conclusion, it was determined that nano-MQL and the lowest level of cutting and feed rate values provided the optimum results.

Extracellular vesicles (EV) such as exosomes, are newly recognized fundamental, natural and physiologic particles of life that seemingly are involved all biologic processes and clinical diseases. Due to their universal involvements, understanding the nature and the potential therapeutic uses of these nano-vesicles requires innovative experimental approaches, in virtually every field. Of the EV group, exosome nano-vesicles and larger companion extracellular micro vesicles (MV) can mediate completely new phenomena dependent on intercellular transfer of proteins and selected RNAs; particularly miRNAs, between donor and targeted cells to elicit epigenetic alterations inducing functional cellular changes. These recipient acceptor cells are nearby (paracrine transfers) or far away after distribution via the circulation (endocrine transfers). The major properties of such vesicles seem to have been conserved over eons, suggesting that they may have ancient evolutionary origins arising perhaps even before cells in the primordial soup from which life evolved. Their potential ancient evolutionary attributes may be responsible for the ability of some modern day exosomes to withstand unusually harsh conditions; perhaps due to unusual membrane lipid compositions. This is exemplified by maternal milk exosome survival of the neonatal acid/enzyme rich stomach. It is postulated that this also applies to their durable presence in phagolysosomes; suggesting unique intracellular release of contents. A major issue discussed is the generally poorly realized superiority of these naturally evolved nano vesicles to therapies compared human engineered artificial nanoparticles; say for treatment of cancers.

A new type of low cost, environmentally friendly wood-plastic composites (WPC) containing carbon nanotubes(CNT)of low content 0%, 0.05wt%, 0.1wt% and 0.15wt%, wood fibers of 14wt% and polymer PES of 86wt% was manufactured by the selective laser sintering (SLS) approach of 3D printing. The experimental results showed that the incorporating of CNTs could obviously increase the mechanical properties of the wood/PES composites material. The tensile strength, bending strength and elasticity modulus were 76.3%, 227.9% and 128.7% higher with 0.1wt% CNTs than without CNTs. And the mechanical properties of specimens firstly increased and then decreased with the increasing contents of CNTs. The SEM results of the specimens’ fracture morphology indicated that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons to explain why the composites possessed the superior mechanical properties: CNTs could facilitate the laser sintering process of wood plastic composites due to their thermal conductivities; also, CNTs could directly reinforce the WPC composites as reinforcement.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

The first paper of this two-part series paper discussed the development of a novel lightweight 3D wood dowel-reinforced glass epoxy hybrid composite material (3DdrFRP) and its manufacturing procedures. It also experimentally compared the performance of scaled utility poles made from conventional 2D E-glass epoxy and 3DdrFRP materials. In the second part, we developed robust finite element (FE) models in LS-DYNA, calibrated them based on experimental results, and used them to simulate the performance of equivalent 2D and 3D poles, proving the integrity of the numerical model. Additionally, we developed a simplified analytical calculation method for engi-neers to determine the stiffness of 3D-DrFRP poles accurately and quickly.

This work deals with the analysis of phase composition of sintered Ti-Al-C composite materials under high voltage electrical discharge. The samples of Ti-Al-C powder composites were tested by SEM, Raman spectroscopy and XRD. It was determined that the treatment of the powder by high voltage electrical discharge (HVED) and further sintering at high temperatures using the method of spark plasma sintering (SPS) encourages the formation of the intermetallic reinforcing phases, carbides and different nanocarbon structures like graphene and fullerenes, as well as pure graphite. Intermetallic phases and nanocarbon structures improve mechanical and physical properties of the composites. By using experimental methods mentioned above, the phase composition of Ti-Al-C powder composites obtained at different sintering temperatures was determined.

Biomass exploitation is a global trend due to the circular economy and the environmentally friendly spirit. Numerous applications are now based on the use of biomass derived products. Hydrogen sulfide (H2S) is a highly toxic and environmentally hazardous gas, which emitted from various processes. Thus, the efficient removal of this toxic hazardous gas following cost effective processes is an essential requirement. In this study, we present the synthesis and characterization of biomass-derived activated-carbon/zinc-oxide (ZnO@AC) composites from different biomass sources as potential candidates for H2S sorption. The synthesis involved a facile method for activated carbon production via pyrolysis and chemical activation of biomass precursors (spent coffee, Aloe-Vera waste leaves, and corncob). Activated carbon production was followed by the incorporation of zinc oxide nanoparticles into the porous carbon matrix using a simple melt impregnation method. The synthesized ZnO@AC composites were characterized using X-ray diffraction (XRD), infrared spectroscopy (IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and nitrogen porosimetry. The H2S removal performance of the ZnO@AC composites was evaluated through sorption experiments using a handmade apparatus. Our findings demonstrate that the Aloe-Vera, Spent-coffee, and Corncob derived composites exhibit superior H2S sorption capacity up to 106 mgH2S/gads., 66 mgH2S/gads., and 47 mgH2S/gads. respectively.

This research examines the fire resistance of geopolymer composites (GCs), formulated using alka-li-activated metakaolin and aluminum powder. The production method involves spray-coating carbon steel plates with fresh GCs, followed by a 28-day curing period at room temperature. Sub-sequently, fire performance and aging tests are conducted to evaluate fire resistance. The study investigates GC properties, including apparent density, bending strength, compression strength, thermal conductivity, porosity, and production cost. Morphological changes before and after fire and aging tests are analyzed using scanning electron microscopy (SEM). Results demonstrate GC foams' outstanding thermal insulation, providing up to 75 minutes of fire resistance with a 6 mm coating, reducing temperatures by 300 °C compared to uncoated steel. GCs exhibit a density of 670 kg/m³, thermal conductivity of 0.166 W/m·K, 68% porosity, and cost efficiency at 250 dollars per cubic meter. This study underscores the potential of foamed geopolymer coatings for effective and economical surface protection.

To study the strengthening effect on recycled concrete columns by carbon fiber composite materials (CFRP) under different levels of seismic damage, four column specimens were designed for pseudo-static tests. The four specimens were respectively non-destructive without strengthening (prototype), non-destructive strengthening, medium seismic damage strengthening and severe seismic damage strengthening, according to the replacement rate of recycled aggregates and the level of seismic damage. The characteristics of the deformation damage and seismic performance indicators of each specimen were compared and analyzed. A decrease was observed in the initial stiffness of the seismically damaged recycled concrete column specimens strengthened with CFRP, while the ductility, peak bearing capacity and energy dissipation capacity of the specimens were improved. On the other hand, with the reduction of seismic damage and the increase of recycled aggregate replacement rate, the ductility and energy dissipation capacity of the reinforced seismic damaged recycled concrete column specimens were enhanced to different levels. In particular, the cumulative energy consumption of the strengthened specimens under medium seismic damage increased most significantly by 32.5%. In general, the hysteretic curves of the strengthened specimens were full, and the average ductility coefficients were 4.1–6.8. CFRP strengthening was more effective in restoring and enhancing the performance of the recycled concrete column specimens with medium and lower seismic damage levels (displacement ratio ≤ 3%).

Two different silica conformations (Xerogels and Nanoparticles) both formed by the mediation of dendritic poly (ethylene imine) were tested at low pHs on the problematic uranyl cation sorption. The effect of crucial factors i.e., temperature, electrostatic forces, adsorbent composition, accessibility of the pollutant to the dendritic cavities and MW of the organic matrix was investigated to conclude the optimum formulation for water purification under these conditions. This was attained with the aid of UV-Visible and FTIR spectroscopy, dynamic light scattering (DLS), ζ-potential; Brunauer–Emmett–Teller (BET) porosimetry, Thermo Gravimetric Analysis (TG) and Scanning Electron Microscopy (SEM) Results highlighted that both adsorbents have extraordinary sorp-tion capacity. Xerogels are cost-effective since they approximate the performance of na-noparticles with much lesser organic content. Furthermore, they are more practicable materials since they may penetrate the pores of a metal or ceramic solid substrate in the form of a precursor, gel-forming solution.

Shear thickening fluids (STF) are a class of fluids whose viscosity significantly rises under external loads. The research on these fluids has been advancing in recent years regarding prospective practical applications, including developing impact-absorbing composites. Following the green agendas governments and legislators advocate, this study investigates the combination of STF and other sustainable materials. Cork is a naturally occurring cellular material with a negative carbon footprint and superior energy absorption properties. With varying concentrations of STF material, cork agglomerates were formed. Notably, the analysed blends are homogeneous, contrasting with previous literary works. A series of experiments were conducted in quasi-static and dynamic conditions to determine the various mechanical responses. STF appears to influence the mechanical behaviour of cork agglomerates by providing softer deceleration rates and dispersing more energy through disaggregation mechanisms.

The use of additive manufacturing in fabricating composite components has been gaining traction in the past decade. However, some issues with mechanical perfor-mance still need to be resolved. The issue of material porosity remains a pertinent one that needs more understanding to be able to determine viable solutions. Different re-searchers have examined the subject of porosity issues in AM-fabricated CFRP compo-sites. However, more research to quantitatively determine the effects of fabrication temperatures at the micro-scale is still needed. This study employed micro CT scan analysis to quantitatively compare the effects of fabrication temperatures at 230°C, 250°C, 270°C, and 290°C for CF-PA and CF-ABS composites. This followed an SEM evaluation which was used to determine the effects of the temperatures on interlayer and intralayer porosity generation. The porosity volume was related to the mechanical properties results in which it was determined how deposition temperatures affect the porosity volumes. It was also determined that semicrystalline composites are generally more affected by fabrication temperatures than amorphous composites, with the rela-tionship between porosity and mechanical properties also established. The overall po-rosity volume from the interlayer and intralayer voids was also determined, with the interlayer voids found to play a more determinant role in influencing the mechanical properties.

A facile and novel synthesis of thirteen 2-amino-3-cyanopyridine derivatives 5(a-m), by a one-pot multicomponent reaction (MCRs), is described for the first time, starting from aromatic aldehydes, malononitrile, methyl ketones, or cyclohexanone and ammonium acetate in the presence of the nanostructured diphosphate Na2CaP2O7 (DIPH) at 80 °C, under solvent-free conditions. These compounds were synthesized in short reaction times with good to excellent yields (84-94%). The diphosphate Na2CaP2O7 is used as an efficient catalyst, environmentally, easy handling, non-toxic, stable, and reusable. Our study was strengthened by the synthesis of five new pyrido[2,3-d]pyrimidine derivatives 6(b, c, g, h, j) by intramolecular cyclization of 2-amino-3-cyanopyridines 5(b, c, g, h, j), with formamide. The synthesized products were characterized by FT-IR, SEM, XRD, TEM, 1H NMR, 13C NMR, TLC, and BET. The operating conditions were optimized using a model reaction in which the catalyst amount, temperature, time, and solvent effect were evaluated. The antibacterial activity was tested against Gram-positive and Gram-negative strains for the synthesized compounds.

The utilisation of the industrial residual products to develop new value-added materials and to reduce footprint is one of the critical challenges of science and industry. Development of the new multifunctional and bio-based composites materials is an excellent opportunity for the effective utilisation of industrial residual products. Keeping the different issues in mind, in this work, we describe the manufacturing and characterisation of the three-phases bio-based composites. The key components are bio-based binder made of peat, devulcanised crumb rubber (DCR) from used tires and part of the fly ash, i.e. the cenosphere (CS). The three-phase composite prepared in the form of a block were investigated for their mechanical properties and density. The three-phase composite was prepared in the form a) of a block were investigated for their mechanical properties, and density and b) a form of granules for determination of the water and oil products sorption were investigated. We have also investigated the dependence of the properties on the DCR and CS fraction. It has been found, that maximum compression strength (in block form) observed for composition without CS and DCR addition was- 79.3 MPa, while the second-highest value of compression strength is 11.2 MPa for composition with 27.3 wt% of CS. For compositions with bio binder content from 17.4 to 55.8 wt% and with DCR contents in range from 11.0 to 62.0 wt%, the compression strength is in the range from 1.1 to 2.0 MPa. Liquid sorption analysis (water and diesel) showed that the maximum saturation of liquids in both cases is set after 35 minutes and ranges from 1.05 to 1.4 g·g -1 for water and 0.77 to 1.25 g·g-1 for diesel. It was noted that 90% of the maximum saturation with diesel fuel comes after 10 minutes and for water after 35 minutes.

In this study, the corrosion performances of ammonium copper quat (ACQ) and boric acid (BA) wood preservatives were investigated, with micronized copper quat (MCQ) and nano boron (NB) used as reference materials. In the study, Scots pine (Pinus sylvestris L.) wood samples were impregnated according to the full-cell process method with ACQ at 2.4% concentration, BA at 4% and MCQ and NB at 1%. The ACQ- and BA-impregnated samples were then impregnated for a second time using five different water-repellent materials: tall oil, linseed oil, sodium silicate, methyl hydrogen silicone and N'-N- (1, 8-Naphthalyl) hydroxylamine. Polyethylene glycol (PEG) 600 and aluminum sulfate were introduced as single impregnations in the form of homogeneous mixtures with the ACQ and BA. The corrosion properties of the impregnated and control samples, including metal weight loss (MWL) and corrosion depth, were examined. As a result, the MWL values of the ACQ-impregnated samples showed an increase compared to the control group. The MWL values of the MCQ-impregnated samples were lower than those of the samples impregnated with ACQ, whilst the MWL values of the BA-impregnated samples were higher than those of the samples impregnated with NB.

The swift progress in low-dimensional nanocarbons, specifically in the realm of the authentic one-dimensional carbon chain featuring sp¹ hybridization, has unveiled exciting prospects for integrating them into cutting-edge technologies across diverse industries. To fully harness their potential, precise control over the growth process is necessary to obtain desired nanostructure and functionality. However, optimizing properties through traditional approaches has been challenging due to complex interactions. To address this, we implement a focused data-driven strategy for nanocarbon inverse design by leveraging a state-of-the-art data-driven nanocarbon genome approach (NCGA). By uncovering relationships between growth parameters and resultant traits, this serves as an expedient catalyst in engineering nanostructures with tailored attributes. We introduce an extensive array of technological approaches aimed at precisely controlling the growth process. These methods encompass stimulating and precisely adjusting synergistic effects, coordinating atomic vibrations at a collective level through the implementation of multilayer nano-interfaces, harnessing the potential of active screen plasma surface engineering, utilizing nano-patterning and allotropic phase transformations, incorporating heteroatom doping, and effectively directing self-assembly. These aim to unlock nanomaterials' latent potential and reveal novel neural pathways within the data-driven NCGA, enhancing its predictive capabilities. Specifically, triggering self-organization during growth can potentially unlock previously unexplored neural pathways. The data-driven NCGA offers a paradigm shift, accelerating discovery and design of nanocarbons with optimized, application-specific properties.

.Various synthetic nematicides are currently used effectively in the control of plant parasitic nematodes. However, these nematicides have adverse effects on humans and the environment. Neem oil is eco-friendly alternatives to synthetic nematicides. The effectiveness of repeated neem oil application in suppressing the root-knot nematodes infestation in figs seedlings was therefore examined in this study, both in its natural form (10 ml/L) and in its nano-emulsion form (5 and 7 ml/L). The recorded reduction parameters of M. incognita were J2/250g soil, galls and egg masses / 5g roots of infected fig seedlings were measured at that time, and the effects of these natural additives were compared with the Fosthiazate (Krenkel 75%EC). The impact of such soil amendments on some typical plant parameters, the total microbial count of soil, and the overall enzymatic activity of the fig rhizosphere were also included. Obtained results revealed that the soil population density of root knot nematode suppressed by 80.3% , reduction of nematode egg masses (60.4%) due to the application of nano-emulsion of neem oil (at 7ml/L). Present work recommend the use of nano-emulsion of neem oil as one of the effective and eco-friendly means to reduce the root- knot nematode on fig .

Numerous structures at the nano- and microscale manifest distinctive properties with far-reaching implications across diverse fields, including electronics, electricity, medicine, and surface engi-neering. Established methods such as nanoimprint lithography, photolithography, and self-assembly play crucial roles in the fabrication of nano- and microstructures; however, they exhibit limitations in generating high-aspect-ratio structures when utilizing high-viscosity pho-tocurable resins. In response to this inherent challenge, we propose a highly cost-effective ap-proach facilitating the direct replication of high-aspect-ratio structures, specifically nanowires, through the utilization of anodized aluminum substrates. This study elucidates the streamlined fabrication process for multiscale porous surfaces achieved through the evaporation-induced in-tegration of solid nanowires printed with high-viscosity photocurable resin.

Natural Fibre Composites (NFC) are eco-friendly, sustainable alternatives to synthetic polymers. However, some intrinsic natural fillers´ properties hinder their widespread implementation as re-inforcement in polymeric matrices and require further investigation. In the scope of this study, the thermal, rheologic, mechanical (tension and flexural modes), morphological properties, water ab-sorption and dimensional stability of the NF polypropylene (PP) based injection moulded compo-sites with the rice husk (rh) and olive pits (op) of 20 wt% and 30% wt%, were investigated. The results suggest that the higher content of the rice husk and olive pits led to a similar reduction of the Melt Flow Index (MFI), independent of the additive type compared to virgin polypropylene (PPv). The melting and crystallization temperatures of the PPrh and PPop composites did not change with statistical significance. The composites are stiffer than the PP matrix by up to 49% and possess higher mechanical strength in what concerns the tension mode at the expense of de-creased ductility. PPrh and PPop have superior flexural modulus in the bending mode, while the flexural strength improvement was accomplished for the PP30%rh. The dimensional stability of the composites was improved as the linear shrinkage in the flow direction was decreased by 49% for PPrh and 30% for PPop, positively correlating with an increase in the filler content and stiff-ness. PPop was less susceptible to water sorption than PPrh due to fibres' composition and larger surface-to-area volume ratios.

In this paper, an intelligent blind guide system based on 2D LiDAR and RGB-D camera sensing is proposed, and the system is mounted on the smart cane. The intelligent guide system relies on 2D LiDAR, RGB-D camera, IMU, GPS, Jetson nano B01, STM32 and other hardware. The main advantage of the intelligent guide system proposed by us is that the distance between the smart cane and obstacles can be measured by 2D LiDAR based on Cartographer algorithm, thus achieving Simultaneous localization and mapping (SLAM). At the same time, through the improved yolov5 algorithm, pedestrians, vehicles, pedestrian crosswalks, traffic lights, warning posts, stone piers, tactile paving and other objects in front of the visually impaired can be quickly and effectively identified. Laser SLAM and improved yolov5 obstacle identification tests were carried out inside a teaching building on the campus of Hainan Normal University and on a pedestrian crossing on Longkun South Road in Haikou City, Hainan Province. The results show that the intelligent guide system developed by us can drive the wheels and omnidirectional wheels at the bottom of the smart cane, and give the smart cane a self-leading blind guide function like a "guide dog", which can effectively guide the visually impaired to avoid obstacles and reach the predetermined destination, and can quickly and effectively identify the obstacles on the way out. The laser SLAM speed of this system is 25~31FPS, which can realize the short-distance obstacle avoidance and navigation function both in indoor and outdoor envionments. The improved yolov5 helps to identify 86 types of objects, the recognition rate for pedestrian crosswalks and for vehicles are 84.6% and 71.8%, respectively; the overall recognition rate for 86 types of objects is 61.2%, and the obstacle recognition rate of the intelligent guide system is 25-26FPS.

The human body contains 60-70% of water, depending on age. As a body fluid, it is not only a medium in which physical and chemical processes take place, but it is also one of the active mediators. Water is the richest substance with non-covalent hydrogen bonds. Water molecules, by themselves (in vacuum), are diamagnetic, but when organized into clusters, become diamagnetic or paramagnetic. Also, biomolecules (DNA, collagen, clathrin, and other proteins) have non-covalent hydrogen bonds in their structure. The interaction, as well as signal transmission, between water and biomolecules is achieved through the vibrations of covalent and non-covalent hydrogen bonds, which determine the state and dynamics of conformational changes of biomolecules. Disruptive conformational changes of biomolecules, cells, and tissues lead to their dysfunctionality, so they are a frequent cause of many disorders and diseases. For example, the rearrangement of hydrogen bonding due to mitochondrial disease mutation in cytochrome bc1 disturbs heme bH redox potential and spin state. In order to prevent and repair the dysfunctional conformational changes, a liquid substance was developed based on the second derivative of the C₆₀ molecule (SD-C₆₀), which has classical and quantum properties. Characterization of SD-C₆₀ by UV-VIS-NIR, FTIR, TEM, and AFM/MFM was done and it is shown that SD-C₆₀ water layers generate vibrations with near-zero phase dispersion which are transmitted through the Fibonacci’s water chains to biomolecules. In comparison to previously published SD-C₆₀ derivate (3HFWC, size until 10 nm, and 1-5 water layers), improved formulation (3HFWC-W, size 10-25 nm, and 6-9 water layers) showed multiplied cytotoxic activity against melanoma cell lines of different aggressiveness. Apart from this, the mode of action was preserved and based on induction of senescence rather than cell death. Importantly, high selectivity toward malignant phenotype was detected. Observed effects can be ascribed to a machinery of hydrogen bonds, which are generated in SD-C₆₀ and transmitted through water to biomolecules. This approach may open a new field in science and healthcare - a “water-based nanomedicine”.

Leather waste was carbonized at 800 °C in inert atmosphere. The resulting biochar was coated in situ with polypyrrole nanotubes produced by the oxidation of pyrrole in the presence of methyl orange. The composites of carbonized leather with deposited polypyrrole nanotubes of various composition were compared with similar composites based on globular polypyrrole. Their molecular structure was characterized by infrared and Raman spectra. Both conducting components formed a bicontinuous structure. The resistivity determined by four-point van der Pauw method was monitored as a function of pressure applied up to 10 MPa. The typical conductivity of composites was of the order of tenths to units S cm−1 and it was always higher for polypyrrole nanotubes than for globular polypyrrole. The conductivity decreased by 1–2 orders of magnitude after treatment with ammonia but still maintained a level acceptable for applications operating under non-acidic conditions. The composites were tested for dye adsorption, viz. cationic methylene blue and anionic methyl orange, using UV-spectroscopy. The composites are designed for the future use as functional adsorbents controlled by the electrical potential.

The main objective of the paper is to investigate the wave propagation behaviour in composites using numerical and experimental methods. Specifically, the study focuses on the actuation of waves by two PZT transducers placed on the surface and embedded at different positions within the composites, namely the quarter and middle positions. The numerical analysis provides simulated results, while the experimental analysis involves practical testing. The paper demonstrates that the numerical results are consistent with the experimental findings. It is observed that when the PZT transducers are placed at deeper positions within the composites, the peak amplitude of the first wave packet for the A0 mode decreases. Overall, the paper contributes to the understanding of wave propagation in composites by comparing the effects of different positions of PZT transducers, both on the surface and embedded within the material. The findings highlight the influence of transducer placement on wave characteristics, particularly the reduction in peak amplitude with deeper transducer positioning.

The rapid advancements in gene therapy have opened up new possibilities for the treatment of genetic disorders, including Duchenne muscular dystrophy, Thalassemia, cystic fibrosis, Hemophilia, and Familial hypercholesterolemia. The utilization of the clustered regularly interspaced short palindromic repeats (CRISPR) - CRISPR-associated protein (Cas) system has revolutionized the field of gene therapy by enabling precise targeting of genes. In recent years, CRISPR/Cas9 has demonstrated remarkable efficacy in treating cancer and genetic diseases. However, the susceptibility of nucleic acid drugs to degradation by nucleic acid endonucleases, necessitates the development of functional vectors capable of protecting the nucleic acids from enzymatic degradation, while ensuring safety and effectiveness. This review aims to explore the biomedical potential of non-viral vector-explore CRISPR/Cas9 systems for the treatment of genetic diseases. Furthermore, it provides a comprehensive overview of recent research advances in viral and non-viral vector-based gene therapy for genetic disorders, including insights from preclinical and clinical studies. Additionally, the review analyzes the current limitations of these delivery systems and proposes avenues for the development of novel nano-delivery platforms.

This paper presents results of the magnetic dynamics study (the microwave power absorptions at the fixed frequencies, during magnetic field sweeping) in samples of Y3Fe5O12 single crystals in the form of plates and spheres of various sizes, at frequencies exceeding 30 GHz, in magnetic fields up to 18 kOe, at room temperature and T=77 K. It was found, that in this case, the inhomogeneity’s of the magnetic state manifested itself in the Y3Fe5O12 samples in as 2D local phase separation regions. These 2D phase separation regions formed inside domain walls representing superlattices with size’s 700 – 900 Å. Landau diamagnetism or de Haas van Alphen oscillations observed in the 2D phase separation regions at room temperature and T=77 K, depending on the shape and size of the studied plates and spheres.

In its 8th Malaysia Plan (MP*), the Malaysian government has given nanotechnology development a high priority and has been made a Strategic Research (SR) programme. Consequently, an exhaustive and long-term approach is essential. Additionally, specific laws are required to provide an optimal health and safety environment for workers. Consequently, the current study intends to assist Malaysian policymakers in promoting improved safety, risk assessment, and management for nanotechnology workplaces, as well as drafting a comprehensive policy for the recently released DOSH guideline in 2018. Utilizing a unique methodology, this study evaluated the assessment and management of nanotechnology health and safety risks in Malaysia using the international risk governance council (IRGC) framework. In addition to document analysis, n = 20 semi-structured interviews were conducted with representatives of several nanotechnology platforms to collect data that was then analyzed thematically. The research evaluated current workplace safety regulations and laws. Consequently, we propose a future dynamic strategy for Malaysian nanotechnology with more favourable upgrades supported by increased concentrations in the following areas: I policy creation, ii) comprehensive management system, iii) knowledge transfer, and iv) infrastructure management. In addition, the findings highlight the need of cross-sectional communication in bridging existing gaps. This study laid the groundwork for a more systematic and comprehensive health and safety strategy.

A comparative analysis of the features of UV- stimulated emission (SE) of various types of disorder active materials based on ZnO crystallites for a random laser (RL) was carried out. The superlinear increase in the intensity of the UV photoluminescence (PL) band of polydisperse nano- microcrystalline (PNMC) ZnO powder at a wavelength of λ = 387 nm and some narrowing of its half-width in the range of 20-15 nm with increasing pump intensity indicate random lasing with incoherent feedback (FB). Properties of similar UV PL bands under the same conditions from a thin film containing hexagonal ZnO microdisks, as well as samples of monodisperse ZnO nanopowder indicate stimulated emission with coherent feedback. It is shown that, among the studied materials, the PNMC ZnO powder with crystallites contained nano-grains with is the most suitable for creating a laser with incoherent feedback at room temperature. The dominant factor of UV SE in PNMC ZnO powder is radiation transitions under exciton - exciton scattering conditions. The possible mechanisms of this random emission with the continuous spectrum are discussed. The average optical gain coefficient αg at λ = 387 nm in this RL system is estimated, as αg ~ 150 cm-1.

Biochar is a carbon allotrope obtained by pyrolysis of biomass, usually agro-waste. Owing to the demand for sustainable development, biochar is continuously raising much hope in the scientific community. However, in order to impart it with new properties, its modification is required, either in situ during pyrolysis, or after the carbonization process. Herein, we propose a new direct approach to obtain bimetallic copper/nickel nanoparticle-loaded on olive stone biochar. The bimetallic-coated biochar and the reference materials bare biochar, copper-loaded and nickel-loaded biochar were prepared at 400 °C under a stream of dinitrogen from olive pit powder particles impregnated first with citric acid (CA), and then with copper and nickel nitrates. We have employed citric acid in the process in order to check its effect on the structural and textural properties of biochar supporting the metallic nanoparticles. Surprisingly, citric acid induced the formation of agglomerated or even raspberry-shaped, bimetallic copper/nickel nanoparticles. Large 450-500 nm-sized agglomerates of ~80 nm bimetallic CuNi NPs were noted for B-CA@CuNi. Interestingly, for biochar material prepared with initial Cu/Ni=10 molar ratio (B-CA@CuNi10/1), the bimetallic NPs formed unusual nano-raspberries (1748 nm in size) which are agglomerates of individual 10-20 nm-sized CuNi10/1 nanoparticles. The B-CA@CuNi and reference materials were characterized by Raman spectroscopy, scanning electron microscopy (SEM)/energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) and magnetometry. The B-CA@CuNi and B-CA@Ni materials could be attracted efficiently with a magnet, but not B-CA@CuNi10/1 due to a low nickel loading. B-CA@CuNi was tested as a catalyst for the degradation of methyl orange (MO). Discoloration was noted within 10 min, much faster than a similar material prepared in the absence of CA. B-CA@CuNi could be recycled at least 3 times with exhibit as fast discoloration catalysis performance. This paper stresses the important role of citric acid in shaping the bimetallic nanoparticles loaded in situ on biochar during the slow pyrolysis process and to enable faster catalysed discoloration of organic dye solution.

The process of water treatment by nanoparticles is one of the most considerable subjects in the cross-field of hydrodynamics, chemistry and mathematics. This paper is dedicated to the case of the flows that appear when squeezing and stretching a spongy with a mix of water with nanoparticles and contaminants. It is assumed that fluid is homogeneous at the starting moment, the parameters of the nanoparticles and contaminants are known, and there is a constant non-homogeneous magnetic field applied to the system. The flow starts moving when the walls of the channel shift to each other. Exact and numerical solutions of the system of ordinary differential equations are used to receive the results. The article gives an answer to the question about stability of the flow and proposes the technique to evaluate the essential characteristics of the system to achieve the treatment process efficiency. The main result is that the considered system shows excellent treatment properties during some part of squeezing stage. This effect does not appear without magnetic field.

The structure of self-reinforced composites (SRCs) based on ultra-high molecular weight 21 polyethylene (UHMWPE) was studied by means of Wide-Angle X-Ray Scattering (WAXS), X-Ray 22 tomography, Raman spectroscopy, Scanning Electron Microscopy (SEM) and in situ tensile testing 23 in combination with advanced processing tools like Avizo, ImageJ, and Ncorr to determine the cor-24 relation between the processing conditions, on the one hand, and the molecular structure and 25 mechanical properties, on the other. SRCs were fabricated by hot compaction of UHMWPE fibers at 26 different pressure and temperature combinations without addition of polymer matrix or softener. 27 It was found by WAXS that higher compaction temperatures led to more extensive melting of 28 fibers with the corresponding reduction of the Herman’s factor reflecting the degree of molecular 29 orientation, while the increase of hot compaction pressure suppressed the melting of fibers within 30 SRCs at a given temperature. X-Ray tomography proved the absence of porosity while polarized 31 light Raman spectroscopy measurements for both longitudinal and perpendicular fiber orienta-32 tions showed qualitatively the anisotropy of SRC samples. SEM revealed that the matrix was 33 formed by interlayers of molten polymer entrapped between fibers in SRCs. Moreover, in situ 34 tensile tests demonstrated the increase of Young’s modulus and tensile strength with increasing 35 temperature.

Lamellar eutectic structure of Al_0.7CoCrFeNi high-entropy alloy (HEA) is emerging as a promising candidate for structural applications because of its high strength-ductility combination. The alloy consists of a fine-scale lamellar fcc+B2 microstructure with high flow stresses >1500 MPa under quasi-static conditions. The response to shear loading was not investigated so far. This is the first report on the shear deformation of an eutectic structured HEA and effect of precipitation on shear deformation. The dynamic shear response (DSR) of the eutectic HEA was examined in two microstructural conditions, with and without the presence of L1₂ precipitates. A split-Hopkinson pressure bar (SHPB) was used to compress the hat-shaped specimens to study the local DSR of the alloy. The adiabatic shear bands (ASBs) in two different microstructural conditions were characterized after deformation at dynamic strain rates. The adiabatic shear localization occurs at low strains for the high strength material, and the eutectic microstructure does not delay cracking. The width of ASBs and the extent of plastic deformation around them has been correlated with the rate of straining. Dynamic recrystallization within ASBs and profuse twinning around it was observed. Local mechanical response of individual lamellae before and after shear deformation was examined using nano-indentation.

A multiscale (micro-macro) approach is proposed for the establishment of the full thermal and induced stress fields in cracked composites that are subjected to heat flow. Both the temperature and stresses distributions are determined by the solution of a boundary value problem with one-way coupling. In the micro level and for combined thermomechanical loading, a micromechanical analysis is employed to determine the effective moduli, coefficients of thermal expansion and thermal conductivities of the undamaged composite. In the macro level, the representative cell method is employed according to which the periodic damaged composite region is reduced, in conjunction with the discrete Fourier transform, to a finite domain problem. As a result, a boundary value problem is obtained in the Fourier transform domain which is appropriately discretized and solved. The inverse transform and an iterative procedure provide the full thermal and stress fields. The proposed method is verified by comparisons with exact solutions. Applications are given for the determination of the thermal and stress fields in cracked fiber-reinforced polymeric composite, cracked porous ceramic material and cracked periodically layered ceramic composite caused by the application of heat flow. The presented formulation admits however the application of a combined mechanical and heat flux on cracked composites.

This paper introduces an innovative nanotechnology-based approach that provides a pathway to enhance the energy release efficiency of nanoenergetic materials (nEMs) by harnessing self-synchronized collective atomic vibrations and phonon wave resonance within the transition domains between nanocomponents, without altering the material composition. The key innovation involves incorporating finely-tuned 2D-ordered linear-chain carbon-based multilayer nano-enhanced interfaces as programmable nanodevices into the transition domains using advanced multistage processing and assembly techniques. These programmable nanodevices enable precise control over self-synchronized collective atomic vibrations and phonon wave propagation, leading to synergistic effects. To activate and optimize these effects, a combination of various methods is employed, including energy-driven initiation of allotropic phase transformations, surface acoustic wave-assisted micro/nano-manipulation, heteroatom doping, directed self-assembly using high-frequency electromagnetic fields, and data-driven inverse design approaches. By leveraging a data-driven inverse design strategy and uncovering hidden structure-property relationships, we maximize energy release efficiency using the carbon nano-materials genome approach derived from multifactorial neural network-based predictive models. This approach not only unlocks new functionalities in nEMs but also improves environmental performance and safety levels. By pioneering transformative pathways for nEMs through harnessing phonon wave resonance in low-dimensional nanocarbon transition interfaces, this research brings significant advancements in the field.

The subject of the conducted study was focused on the development of new type of technical blends reinforced with natural fillers. The study was divided into two parts, where in the firsts stage of the research unmodified POM was reinforced with different types of natural fillers: cellulose, wood flour and husk particles. In order to select the type of filler intended for further modification, the mechanical characteristics was assessed. The 20% wood flour (WF) filler system was selected as the reinforcement. The second stage of research involved the use of combination of polyoxymethylene POM and poly(lactic acid) PLA. POM/PLA blend (ratio 50/50 %) were modified with elastomeric compound (EBA) and chain extender as reactive compatibilized (CE). The microscopic analysis revealed that for POM/PLA system the filler-matrix interface is characterized by better wettability, which might suggest higher adhesion. The mechanical performance revealed that for POM/PLA-based composites the properties were very close to the results for POM-WF composites; however, there is still large difference in thermal resistance in favor of POM-based materials. The increase in thermomechanical properties for POM/PLA composites occurs after heat treatment. The increasing crystallinity of the PLA phase allows for an significant increase of the head deflection temperature (HDT), even above 125 °C.

Fire is a significant threat to human life and civil infrastructures. Builders and architects are hankering for safer and sustainable alternatives of concrete that do not compromise with their design intent or fire safety requirements. The aim of the present work is to improve the residual compressive performance of concrete in the post-fire exposure, by incorporating by-products from urban residues. Based on sustainability and circular economy motivations, the attention is focused on rubber tire fly ash, aged brick powder, and plastic (PET) bottle residuals used as partial sand replacement. The selected by-products from urban residues are used for the preparation of Cement-Based Composites (CBCs) in two different proportions (10 % and 15 %). The thermal CBC behaviour is thus investigated under realistic fire scenarios (i.e., Direct Flame (DF) for 1 hour (1h)), by following the ISO 834 standard provisions, but necessarily resulting in non-uniform thermal exposure for the cubic specimens. The actual thermal exposure is further explored with a Finite Element (FE) model, giving evidence of thermal boundaries effects. The post-fire residual compressive strength of heated concrete and CBC samples is hence experimentally derived, and compared to unheated specimens in ambient conditions. From the experimental study, the enhanced post-fire performance of CBCs with PET bottle residual is generally found superior to other CBCs or concrete. The structure-property relation is also established, with the support of Scanning Electron Microscopy (SEM) micrographs. Based on existing empirical models of literature for the prediction of the compressive or residual compressive strength of standard concrete, newly developed empirical relations for both concrete and CBCs are assessed.

This paper addresses investigation of guided-wave excitation by angle-beam wedge piezoelectric transducers in multi-layered composite plate structure with orthotropic symmetry of the material. The aim of the present study is to determine the capability of such actuators to provide the controlled generation of an acoustic wave of a desirable type with the necessary wavelength, propagation distance and directivity. The studied CFRP panel is considered as homogenous with effective elastic moduli and anisotropic structural damping, whose parameters were determined experimentally. According to the results of dispersion analysis and taking into account the data of wave attenuation in a highly damping CFRP composite, the two types of propagating waves A0 and S0 were considered theoretically and experimentally in the frequency range 10 - 100 kHz. Using the results of a previous study, the structure of the wedge actuator was reconstructed to develop its finite element (FE) model, and a modal analysis was carried out, which revealed the most intense natural vibration modes and their eigenfrequencies within the used frequency range. Both experimental and numerical studies of the generation, propagation, directivity and attenuation of waves in the orthotropic composite panel under study revealed the influence of the angular orientation of the actuator on the formation of wave patterns and allowed to determine the capabilities of the wave's directivity control.

The capacity and the mechanism of the adsorption of aqueous barium (Ba), cobalt (Co), strontium (Sr) and zinc (Zn) by Ecuadorian (NatAllo) and synthetic (SynAllo-1 and SynAllo-2) allophanes were studied as a function of contact time, pH and metal ion concentration using kinetic and equilibrium experiments. The mineralogy, nano-structure and chemical composition of the allophanes were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy and specific surface area analyses. The evolution of adsorption fitted to a pseudo-first-order reaction kinetics, where equilibrium between aqueous metal ions and allophane was reached within < 10 min. The metal ion removal efficiencies varied from 0.7 to 99.7 % at pH 4.0 to 8.5. At equilibrium, the adsorption behavior is better described by the Langmuir model than by the Dubinin-Radushkevich model, yielding sorption capacities of 10.6, 17.2 and 38.6 mg/g for Ba^(2+), 12.4, 19.3 and 29.0 mg/g for HCoO_2^-, 7.2, 15.9 and 34.4 mg/g for Sr^(2+) and 20.9, 26.9 and 36.9 mg/g for Zn^(2+), respectively, by NatAllo, SynAllo-2 and SynAllo-1. The uptake mechanism is based on a physical adsorption process. Allophane holds great potential to remove aqueous metal ions and could be used instead of zeolites, montmorillonite, carbonates and phosphates for wastewater treatment.

This work is concerned with studying the change of some Optical and Electrical Properties of Ba_xFe_(1-x)TiO₄ thin films due to the change of the nano crystal size. Simple theoretical explanation based on the string theory was developed. The empirical results obtained indicated that the absorption coefficient, electrical conductivity, and the magnetic permeability increase upon decreasing the nano crystal size. However, the transmission coefficient, and the refractive index increase upon increasing the nano crystal size. All these changes are explained using a simple string model with the aid of Newton's laws. The capability of the string theory to explain this nano quantum behavior comes from the fact that the string theory recognize both the particle and the wave nature of the nano system. This is similar of course to the quantum approach which is based mainly on the dual wave particle nature of atomic systems and entities.

Control of autonomous robot motion in radial mass density field is presented. In that sense the robot motion is described as the function of the radial mass density parameters. The radial mass density field is between the maximal radial mass density and the minimal radial mass density. Between these two limited values one can use n points (n = 1, 2, . . . nmax) and calculate the related radial mass density for each point. The radial mass density is maximal at the minimal gravitational radius and minimal at the maximal gravitational radius. This conclusion is valid for Planck scale, but also for the scales that are less or higher of that one. Using the ratio of the Planck mass and Planck radius it is generated energy conservation constant with value κ = 0.99993392118. Further, in this theory it is possible to connect Planck’s and gravitational parameters as functions of the maximal (or minimal) radial mass density. In that sense the autonomous robot motion in radial mass density field is important for the control of the robot motion at micro and nano scales.

Erosion caused by the repeated impact of particles on a substance surface is a usual wear method resulting in gradual and continual loss of objects. It is a crucial problem in several modern industries because their surfaces are frequently subjected to destructive erosive situations. Polymers and their hybrid materials include several applications to be used as a coating in the form of powder for different applications. This review paper aims to provide extensive information on the erosion behavior of thermoset and thermoplastic neat resin and their hybrid materials composites. Focus is specifically paid to highlight the influence of properties of selected materials, impingnation parameters such as incident Angle of erodent, impact velocity of erodent, erodent nature, and the erosion mechanism. The review further extends the information about the erosion techniques and numerical simulation methods used for wear studies of surfaces. An investigation has been carried out for researchers to explore the selection of materials and methods in terms of conditions and parameters to meet the current and future needs and challenges for the protection of surfaces of the advanced industries. During review according to the findings achieved from the literature of the past fifty years, it has been noted that the thermoplastic nature of the composite is a key component to determine the anti-wear properties, the composites with lower glass transition, higher ductility, and greater crystallinity can provide better protection to erosion in advance surface applications.

Biosensors are measurement devices that can sense several biomolecules, and are widely used for the detection of relevant clinical pathogens such as bacteria and viruses, showing outstanding results. Because of the latent existing risk of facing another pandemic like the one we are living due to COVID-19, researchers are constantly looking forward to developing new technologies for diagnosis and treatment of infections caused by different bacteria and viruses. Regarding that, nanotechnology has improved biosensors design and performance through the development of materials and nanoparticles that enhance their affinity, selectivity, and efficacy in detecting these pathogens, such as employing nanoparticles, graphene quantum dots, and electrospun nanofibers. Therefore, this work aims to present a comprehensive review that exposes how biosensors work in terms of bacterial and viral detection, and the nanotechnological features that are contributing to achieving a faster yet still efficient COVID-19 diagnosis at the point-of-care.

The paper is aimed to develop an improved acoustic-based Structural Health Monitoring (SHM) and Non-Destructive Evaluation (NDE) techniques, which provide the waves directivity emitting by the angle-beam wedge actuators in the thin-walled structures made of plastic materials and polymeric composites. Our investigation includes the dispersive analysis of the waves that can be excited in the studied plastic panel. Its results allowed to find two kinds of the generated acoustic waves - anti-symmetric Lamb waves A0 and shear horizontally polarized SH waves SS0. The bounds of the chosen frequency range for the experimental and numerical studies were accepted as a compromise between the desire to obtain high defects resolution by generating short waves, their adjustable directivity and maximum propagation length. The finite element model for the transducer was built by using the results of actuator structure experimental study. The frequency response functions for the actuator current and oscillation amplitude of the footprint surface demonstrated good agreement. The found eigenfrequencies of actuator's structure were used for the numerical and experimental study of the Lamb and SH wave generation and propagation in a thin-walled plastic panel. Our results convincingly demonstrated the satisfactory directivity of the actuated waves at their excitation on the frequencies that corresponded to the natural modes of the actuator oscillation. The authors assume that an efficient use of the proposed technique for other analyzed quasi-isotropic materials and applied actuators can be provided by a preliminary research using the similar approach and methods presented in this article.

Direct laser writing three-dimensional nano-lithography is an established technique for manufacturing functional 3D micro- and nano-objects via non-linear absorption induced polymerization process. In this Chapter an underlying physical mechanisms taking place during nano-confined polymerization reaction, induced by tightly focused ultra-short laser pulses, are reviewed and discussed. The special attention is paid on the effects that directly impact structuring resolution and minimum achievable feature size. Analysis of possible photo-initiation mechanisms as contributing multi-photon absorption and avalanche ionization in pre-polymers under diverse exposure conditions (wavelength, pulse duration) is presented. Feasible structuring of pure (non-photosensitized) and functional nanoparticles doped polymer precursors is justified and benefits of such materials/structures for microoptics, photonics and cell scaffolds are highlighted. The influence of temperature effects (induced by writing process itself or determined by ambient conditions) on polymerization process, observed in different pre-polymers under diverse exposure regimes is outlined. The further adjustment of the structuring resolution is possible via precise control of light polarization and diffusion assisted radical quenching. The work is concluded with a brief outlook on future challenges and perspectives related to refinement of 3D ultra-fast laser lithography fabrication process in the means of application of diverse post-processing methods and research into novel photo-curable materials including inorganic ones.

Given the rise in the number of cases and their recurrences, Urinary Tract Infections (UTI) are one of the major burdens on public healthcare worldwide. Rapid, inexpensive and selective detection of Uropathogenic E. coli (UPEC), a major contributor to UTIs, is the need of the hour for effective treatment, given the rise of antibiotic-resistant bacteria due to improper diagnosis. Here we present a rapid, real-time, selective and label-free detection of UPEC using an integrated sensing platform based on Crossed Surface Relief Gratings (CSRGs) as nanoplasmonic sensors. Detection is achieved due to the unique Surface Plasmon Resonance (SPR)-based light energy exchange attributed to the CSRGs, allowing real-time sensing in a very narrow bandwidth of the incident light to pass where the SPR energy conversion occurs. The sensing ability of the platform is experimentally demonstrated by the detection of bulk Refractive Index (RI) changes, with a bulk sensitivity of 382.2 nm/RIU and a resolution in the order of 10-6 RIU. We demonstrate selective capture and detection of clinical concentration of UPEC, as opposed to other gram-negative bacteria, in real-time, a first for CSRGs. This work is particularly important for effective treatment of UTIs, allowing point-of-care diagnosis for economically disadvantaged regions around the world.

A new generation of nano-technologies is expanding solid propulsion capabilities and increasing their relevance for versatile and manoeuvrable micro-satellites with safe high-performance propulsion. We propose the innovative concept, connected with application of new synergistic effect of the energetic materials performance enhancement and reaction zones programming for the next generation small satellite multimode solid propulsion system. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon, by the properties of the energetic materials reaction zones and by localization of the energy release areas. This synergistic effect can be provided through application of the functionalized carbon-based nanostructured metamaterials as a nano-additives along with simultaneous manipulating by their properties through the electrostatic field. Mentioned effect will be controlled through predictive programming both by the spatial structure and physics-chemical properties of the functionalized carbon-based nano-additives and through the electromagnetic control of the self-organized wave pattern excitation and micro- and nano- scale oscillatory networks in the energetic material reaction zones. Suggested new concept makes it possible to increase the energetic material regression rate and increase the thrust of the solid propulsion system with minimal additional energy consumption.