Several factors, such as internal algorithm, sensor technology, and obsolescence might skew outcomes when comparing different gas analysers measurements during CPET. Besides aerosol borne infectious disease are a source of contamination during cardiopulmonary exercise tests (CPET). Thus, the main aim of this study was to determine the agreement degree between the Quark RMR and the Jaeger Oxycon Pro, using an antibacterial filter with the latter. Forty-two participants (19-54 years old) performed two non-consecutive maximal graded exercise tests on a cycle-ergometer on two counterbalance and different days using the Oxycon Pro and the Quark RMR in a randomized order. Differences between devices were tested using a generalized linear model adjusted by Bonferroni, and correlation and agreement was assessed using Pearson’s correlation coefficient (R), intraclass coefficient correlation (ICC), Lin’s concordance correlation coefficient (CCC) and Bland-Altman plots. No significant differences were found between devices in any of metabolic or ventilatory parameters for cardiorespiratory fitness assessment (VO_2max: 3131.3±882.1 vs. 3189.8±894.8, p=0.071, VCO_2max: 3436.3±936.0 vs. 3550.3±1043.2, p=0.071, for Quark RMR and Oxycon Pro, respectively). However, Bland-Altman plots showed a trivial tendency towards Oxycon Pro overestimation relative to Quark RMR as air flow volume increases. Both devices showed strong correlation and high level of agreement during maximal and submaximal exercise intensities (Pearson’s R: 0.974 & 0.977; ICC: 0.985 & 0.987; Lin’s CCC: 0.971 & 0.974, for VO₂ and VCO₂, respectively). Therefore, providing consistency to CPET data comparison between both devices, and insight into whether the use of these metabolic carts could be interchangeable or combined when a single device cannot be used for CPET assessment.

Among all Brazilian economic sectors, the livestock sector stands out due to its large production and high export volume. However, beef production is associated to significant environmental impacts, such as deforestation and greenhouse gas (GHG) emission. The Paris Agreement was settled to avoid that global mean temperature rise up to 1.5 – 2º C by 2100. In 2020, Brazil committed in its nationally determined contribution (NDC) to reduce its GHG emission by 43% until 2030. This study aims to identify the association of beef production and beef cattle emissions, as well as assess predictive GHG emission scenarios for 2030 and value these emissions. To translate the environmental impacts of beef production into economic impacts, and thus amplify the discussion, we valued GHG emissions using the social cost of carbon (SCC). The results showed that the business as usual (BAU) GHG emission derived from beef production would range between 0.423 and 0.634 GtCO₂e in 2030, whereas the maximum emission estimated to meet the NDC should be 0.257 GtCO₂e. The SCC revealed the opportunity to reduce between US $18.8 and $42.6 billion in the cost of BAU emissions from beef production in 2030 if the NDC is met. Lastly, assessing a scenario where climate targets and beef exports are prioritized, between 2-10 kg of beef per capita would be available in the domestic market in 2030. Our results reveal the need and urgency of changes in livestock production to emit less GHG per kg of beef produced, and the avoided monetary cost of reducing emissions.

Rotary drilling for oil and natural gas uses drilling fluid for lubrication of the bit, to seal off unstable shale layers, and floating out rock cuttings. Drilling fluid is a water-clay chemical mixture. Produced water is a water-sand chemical mixture. Land farming is a common disposal technique of drilling fluid and produced water. In the land farming process, amendments of fluid are repeatedly applied to the soil surface. Plant growth and soil chemical properties may be altered by additions of drilling fluid, because of alkalinity, salinity, trace elements, and petroleum residue contained in waste. The objective of this study was to determine the change in soil pH, electrical conductivity (EC), total nitrogen and carbon, and extractable nutrient levels following the land application of drilling fluid and produced water. The study was a comparison of three plots with similar soil properties and conditions. The three study plots had various levels of drilling fluid and produced water applications. The data show a major difference from field-to-field for EC, Na, and Cl levels. The EC and salt levels increased with additional applications of drilling fluid and produced water. The percent total nitrogen values and plant available P levels were very low in all fields. High EC and salt values, coupled with low N and P levels, would be detrimental to plant growth and development. To successfully vegetate this land-farm site, application of N and P fertilizer would be required. This study will help to give a better understanding of practical ways to land-farm drilling fluid and produced water in a fashion that both minimizes environmental issues and is economically feasible. Salinity changes to soil were expected to be high; there are excessive amounts of sodium and chloride in spent drilling fluid and produced water.

In the increasingly complex environment of downhole working conditions such as frequent opening and closing of oil and gas wells, acidification/multi-stage fracturing, steam huff and puff, and strong injection and production, the traditional casing string design method standards based on strength design have gradually highlighted their limitations. It is necessary to formulate string design method standards that consider the full life cycle of wells such as drilling and completion, fracturing, and production operations. Starting from the analysis of the advantages and disadvantages of traditional casing string design methods, this paper presents the characteristics of the strain design methods and seal design methods that have been formulated for the life cycle of the string. The strain design method breaks through the traditional design concept and allows the design concept of controllable deformation of the pipe string. The sealing design method is currently the only standard method for the design of tubing strings. At the same time, it further proposes to consider the trend of pipe strength deterioration and establish a time dimension-based life cycle pipe string design method standard, which effectively solves the safety problem of pipe string design in production and operation.

The expansion of unconventional oil and gas development (UD) across the US continues to be at the center of debates regarding safety to health and the environment. This study evaluated the water quality of private water wells in the Eagle Ford Shale within the context of community members’ perceptions. Community members (n=75) were surveyed regarding health status and perceptions of drinking water quality. Water samples from respondent volunteers (n=19) were collected from private wells and tested for a variety of water quality parameters. Of the private wells sampled, 8 had exceedances of MCLs for drinking water standards. Geospatial descriptive analysis illustrates the distributions of the well exceedance as well as the well owners’ overall health status. Surveys showed that the majority of respondents received their water from a municipal source and were significantly more distrustful of their water source than of those on private wells. In many cases, there are statistically significant differences between self-reported, provider undiagnosed conditions and self-reported, provider diagnosed conditions. Attitudes and perceptions of water quality may play an important role in the overall perceived health status of community members in high fracking regions.

This article should examine ideas of how a chatbot can support decision making processes by col-lecting general opinion about the certain topics. The ChatGPT is tested in this article in respect of natural gas security of supply of the Republic of Serbia in the context of the current political situation in the world. The author first describes its own stance on the topic and then the ChatGPT is asked for its opinion (which most probably collects and compiles phrases from English speaking sources to build a text in a smart way). The topic is ort only about security of gas supply of Serbia but also political and highly sensitive, so it is examined if the ChatGPT can be useful tool to reach a balance between less on more favorable options in the process of policy making.

Two-dimensional (2D) transition metal dichalcogenides (TMDCs) nanosheets have shown extensive applications due to their excellent physical and chemical properties. However, the low light absorption efficiency limits their application in optoelectronics. By rolling up 2D TMDCs nanosheets, the one-dimensional (1D) TMDCs nanoscrolls are formed with spiral tubular structure, tunable interlayer spacing and opening ends. Due to their increased thickness of scroll structure, the light absorption is enhanced. Meanwhile, the rapid electron transportation is confined along the 1D structure. Therefore, the TMDCs nanoscrolls show improved optoelectronic performance compared to 2D nanosheets. In addition, the high specific surface area and active edge site from bending strain of basal plane make them promising materials for catalytic reaction. Thus, the TMDCs nanoscrolls have attracted intensive attention in recent years. In this review, the structure of TMDCs nanoscrolls is firstly demonstrated and followed by various preparation methods of the TMDCs nanoscrolls. Afterwards, the applications of TMDCs nanoscrolls in the fields of photodetection, hydrogen evolution reaction, and gas sensing are discussed.

Flammability was evaluated and the results showed the values of critical flux at extinguishment (CFE) as 49.5kW/㎡ on average, total heat release (Qt) as 0.21MJ on average, and peak heat release rate (Qp) as 0.66kW on average, which satisfied all of the thresholds presented by the IMO. Therefore, flame-retardant plywood, of which the flame-retardant performance was evaluated, was determined to be an applicable finishing material that satisfies fire safety standards.

ZnO thin films with a thickness of 300 nm were deposited on Si and Al2O3 substrates using electron beam evaporation technique with the aim to be tested as low cost and low power consumption gas sensors for ozone (O3). To characterize the surface roughness and the grain size, which are the main parameters recognized to enhance gas sensitivity since they directly influence the effective sensing area, surface morphology and roughness analyses of the films were performed using scanning electron microscopy and atomic force microscopy, respectively. The crystalline structure and elemental composition were studied through Raman spectroscopy and X-ray photoelectron spectroscopy. Gas tests were conducted at room temperature and zero-bias voltage to assess the sensitivity and response as a function of time of the films to O3 pollutant. The results indicate that the films deposited on Al2O3 exhibit promising characteristics, such as high sensitivity and a very short response time (< 2 s) to the gas concentration. Additionally, it was observed that the films display pronounced degradation effects after a significant exposure to O3.

Researchers have been exploring seaweed to reduce methane (CH4) emissions from livestock. This study aimed to investigate the potential of a red alga, Bonnemaisonia hamifera, as an alternative to mitigate CH4 emissions. B. hamifera, harvested from the West coast of Sweden, was used in an in vitro experiment using a fully automated gas production system. The experiment was a ran-domized complete block design consisting of a 48-h incubation that included a control (grass si-lage) and B. hamifera inclusions at 2.5%, 5.0% and 7.5% of grass silage OM mixed with buffered rumen fluid. Predicted in vivo CH4 production and total gas production were estimated by ap-plying a set of models to the gas production data and in vitro fermentation characteristics were evaluated. The results demonstrated that the inclusion of B. hamifera reduced (P = 0.01) predicted in vivo CH4 and total gas production, and total gas production linearly decreased (P = 0.03) with higher inclusion of B. hamifera. The molar proportion of propionate increased (P = 0.03) while isovalerate decreased (P = 0.04) with inclusion of B. hamifera. There was a tendency for increased (0.06 ≤ P ≤ 0.10) total volatile fatty acid production, as well as lower proportions of butyrate, isobutyrate, and 2-methylbutyrate. Chemical analyses revealed that B. hamifera had moderate concentrations of polyphenols. The iodine content was low and there was no detectable bromo-form, suggesting quality advantages over Asparagopsis taxiformis. Additionally, B. hamifera exhib-ited antioxidant activity comparable to the positive control Resveratrol. The findings of this study indicated that B. hamifera harvested from temperate waters in Sweden possesses capacity to mitigate CH4 in vitro.

Inert gas asphyxiation is a rarely observed form of suffocation in which the decedent breathes in an inert chemical, such as helium or nitrogen, in the absence of oxygen. The ultimate cause of death is not a result of the chemical itself, but rather from the oxygen starvation as the inert gas displaces vital oxygen. In this case report, a 66-year-old Caucasian female with a history of gastroparesis, degenerative disc disease, and chronic pain was found deceased with a plastic bag secured around her head. Plastic tubing terminated inside the bag and connected to a nearby canister of nitrogen gas. This case study discusses the challenges in determining inert gas asphyxiation as the cause of death in a postmortem setting and emphasizes the importance of understanding the decedent’s history and context of the environment in which they were found.

Gas embolism is a medical condition leading to the blockage of blood flow in the microvasculature by gas bubbles. While reported as rare, gas embolism often has devastating, fatal physiological consequences. Despite this acute importance, the genesis and evolution of air bubbles in blood vessels under different physiological conditions, such as blood viscosity and blood flow rate, is still understudied, largely because of difficult experimentation and in situ visualization. The objective of this work was to study the gas embolism phenomenon in vitro, using a microfluidic system that mimicked the architecture of microvasculature. The microfluidic systems comprised linear channels with two different air inlet types, namely, T- and Y-junctions with three different widths (20 µm, 40 µm, and 60 µm), and a 30 µm width honeycombed network with three bifurcation angles (30°, 60°, and 90°). Three synthetic liquids equivalent to 0%, 20%, and 46% hematocrit that mimicked the physiological blood viscosity and hematocrit concentrations were used. Our results show that: (i) 20 µm and 40 µm width channels had an elevated risk of gas embolism due to wide fluctuations in the total slug sizes; (ii) the resistance to the flow of air bubbles increased with the increase in the equivalent concentration of hematocrit; (iii) gas bubbles causing blockages and dampening of the flow velocity were frequently observed in 20 µm channels, and lastly (iv) increased risk of gas embolism was observed in the honeycomb architecture with 60° and 30° bifurcations. This work suggests that in vitro experimentation using microfluidic devices with microvascular tissue-like structures opens the possibility of studying this medical condition with high reproducibility and impacts the fact-based medical guidelines for preventing or mitigating iatrogenic occurrences.

Accurate prediction of mercury content emitted from fossil-fueled power stations is of utmost importance for environmental pollution assessment and hazard mitigation. In this paper, mercury content in the output gas of power stations’ boilers was predicted using an adaptive neuro-fuzzy inference system (ANFIS) method integrated with particle swarm optimization (PSO). The input parameters of the model include coal characteristics and the operational parameters of the boilers. The dataset has been collected from 82 power plants and employed to educate and examine the proposed model. To evaluate the performance of the proposed hybrid model of ANFIS-PSO model, the statistical meter of MARE% was implemented, which resulted in 0.003266 and 0.013272 for training and testing, respectively. Furthermore, relative errors between acquired data and predicted values were between -0.25% and 0.1%, which confirm the accuracy of the model to deal nonlinearity and representing the dependency of flue gas mercury content into the specifications of coal and the boiler type.

The hydrodynamic results obtained from the permeability of porous materials not only affect the assessment of the stream of the gas flow through those materials but they also refer to the loss of pressure energy in that flow. The direct measure of that loss is flow resistances.The results of experimental research upon the assessment of the flow resistances of porous materials with respect to gas flow. The research conducted applied to natural materials with an anisotropic gap-porous structure. The tests were carried out on a gas permeability measuring system, adapted to different shapes of porous material samples. The process issue of the total pressure drop on a porous deposit was considered in the Reynolds number category. The coefficient of flow resistance for anisotropic materials was defined and the value of this coefficient was compared to the gas stream and the total pressure drop on the porous bed was experimentally evaluated.

The one-dimensional gas of bosons interacting via a repulsive contact potential was solved long ago via Bethe's ansatz by Lieb and Liniger [Phys. Rev. {\bf 130}, 1605 (1963)]. The low energy excitation spectrum is a Luttinger liquid parametrized by a conformal field theory with conformal charge $c=1$. For higher energy excitations the spectral function displays deviations from the Luttinger behavior arising from the curvature terms in the dispersion. Adding a corrective term of the form of a mobile impurity coupled to the Luttinger liquid modes corrects this problem. The ``impurity'' term is an irrelevant operator, which if treated non-perturbatively, yields the threshold singularities in the one-particle and one-hole hole Green's function correctly. We show that the exponents obtained via the finite size corrections to the ground state energy are identical to those obtained through the shift function.

High-throughput screening of samples is the strategy of choice to detect occupational exposure biomarkers, yet it requires user-friendly apparatus that gives relatively prompt results while ensuring high degrees of selectivity, precision, accuracy and automation, particularly in preparation processes. In the last 10 years, miniaturization has attracted much attention in analytical chemistry and has driven solvent and sample savings and easier automation, the latter thanks to the introduction on the market of three axis autosampler. In light of the above, this contribution describes a novel user-friendly solid-phase microextraction (SPME) off- and on-line platform coupled with gas chromatography triple quadrupole-mass spectrometry to determine urinary 1- and 2-hydroxy-napthalene, 9-hydroxy-phenantrene, 1-hydroxy-pyrene, 3- and 9-hydroxy-benzoantracene and 3-hydroxy-benzo[a]pyrene, metabolites of the related polycyclic aromatic hydrocarbons. In this new procedure chromatography’s sensitivity is combined with the user-friendliness of N-tert-butyldimethylsilyl-N-methyltrifluoroacetamide on-fiber SPME derivatization previous direct immersion sampling, to which is added the quantitative accuracy afforded using specific isotope-labelled internal standards. The detection limits for the seven OH-PAHs were ranged from 0.28 to 1.87 ng/L. Intra-(from 2.5 to 3.0%) and inter-session (from 2.4 to 3.9%) repeatability was also evaluated. This method serves to identify suitable risk-control strategies for occupational hygiene conservation programs

This research was conducted with the aim of knowing how to compare the financial performance of the oil and gas trading industry with cross-sectional analysis techniques. The type of research conducted in this research is qualitative research with research objects at several companies, namely PT Radiant Utama Interinsco Tbk, PT Elnusa Tbk, PT AKR Corporindo Tbk, and PT Aneka Gas Industri Tbk. The data used in this study comes from secondary data, namely the internet in the form of company financial reports for the 2019-2021 period obtained from the Indonesia Stock Exchange. The results of this study indicate that PT Radiant Utama Interinsco Tbk has the best financial performance on inventory turnover ratio and average age, PT Elnusa Tbk has good inventory performance on current ratio, quick ratio, DAR, and DER., PT AKR. Corporindo Tbk has performed well on the ratios of TIE, FCC, Dividend Payout, Dividend Yield, and PER. PT Aneka Gas Industri Tbk has performed well on the ratio of Receivables Turnover Ratio and Average Age of Receivables.

Large ruminant production in developing countries is inefficient with low growth rates and likely high greenhouse gas emissions (GHGe) per unit of meat or milk produced. Trials conducted in Lao PDR from 2017-2020, studied ad-libitum supplementation for 12 weeks with 20kg high quality molasses nutrient blocks (MNB; Four Seasons Pty Ltd, Brisbane, Australia), that were either: non-medicated (NMB); fenbendazole-medicated (FMB5, Panacur100®, Coopers Australia, @ 5g/kg); triclabendazole-medicated (TMB5 or TMB10, Fasinex®, Novartis Australia, @ 5g/kg or @ 10g/kg, respectively); or formulated with urea (UMB8 or UMB10 @ 8% or 10% urea, respectively). Average daily gains (ADG) were determined for access to all MNB’s and compared with access to NMB’s, no supplementation, or previously determined free-grazing baseline ADG’s (55–84g in cattle; 92–106g in buffalo). ADGs were significantly improved following access to all MNBs for periods up to 12wks. ADGs following access to UMB8 or NMB were calculated for three age cohorts of cattle: young calves <8m (238-298g), growing cattle (143-214g) and lactating cows (179-191g). Modelling using IPCC Inventory software model V 2.69 of published data demonstrated a conservative net abatement of 350kg CO2e was achievable over a 200 day feeding period. An additional trial of Emissions control blocks (EMB’s, n = 200) distributed to farmers (n = 60) and two educational institutions, was conducted. Consumption rates (156g/day) and farmer and institutional acceptance of EMB’s were similar to published findings with other MNB’s, confirming all MNB’s and EMB’s improved animal productivity and body condition score, with healthier animals that were easier to manage. Modelling of changes in GHGe intensity identified an abatement of 470kg CO2e per EMB consumed, delivering a total project emissions abatement of 94t CO2e. Provision of MNBs and EMBs in smallholder large ruminant production systems is likely to achieve impressive abatement of GHGe due to improved efficiency of rumen fermentation and productivity.

Gas flaring is commonly used by industrial plants for processing oil and natural gases in the atmosphere, and hence is an important anthropogenic source for various pollutants including CO₂, CO, and aerosols. This study evaluates the feasibility of using satellite data to characterize gas flaring form space by focusing on the Khanty Mansiysk Autonomous Okrug in Russia, a region that is well known for its dominatingly gas flaring activities. Multiple satellite-based thermal anomaly data products at night are inter-compared and analyzed, including MODIS (Moderate Resolution Imaging Spectroradiometer) Terra level-2 Thermal Anomalies product (MOD14), MODIS Aqua level-2 Thermal Anomalies product (MYD14), VIIRS (Visible Infrared Imaging Radiometer Suite) Active Fires Applications Related Product (VAFP), and VIIRS level-2 data based Nightfire product (VNF). The analysis compares and contrasts the efficacy of these sensor products in detecting small, hot sources like flares on the ground in extremely cold environments such as Russia. We found that the VNF algorithm recently launched by NOAA has the unprecedented accuracy and efficiency in characterizing gas flares in the region owing primarily to the use of Shortwave Infrared (SWIR) bands. Reconciliation of VNF’s differences and similarities with other nighttime fire products is also conducted, indicating that MOD14/MYD14 and VAFP data are only effective in detecting those gas flaring pixels that are among the hottest in the region. Validation of VNF product of gas flaring location with Google Earth images are made. It is shown that that VNF’s estimates of gas flaring area (the area of gas flaming) agree well the counterparts from Google images with a linear correlation of 0.91, highlighting its potential use for routinely monitoring emissions of gas flaring from space.

This article provides a comprehensive analysis of the global gas and liquefied natural gas (LNG) markets. The article begins by discussing the increasing demand for gas and LNG, particularly in Asia, as countries aim to transition to cleaner sources of energy. It explores how market volatility has led to energy security interventions and lasting economic and emissions impacts. It then explores the global supply and demand dynamics, highlighting the structural change expected in the market and the competition between Europe and Asia for limited new LNG supply. The article also focuses on Europe's increased flexibility and dependence on LNG imports, which have risen by 60% to 121 million tonnes, offsetting lower Russian pipeline imports. Furthermore, the article delves into global supply and demand dynamics, how the market is expected to remain tight, and how record gas and LNG prices have led to demand reductions. Additionally, it analyzes the future outlook and investment needs, highlighting the continued uptake of gas in heavy-duty transport and the need for further investment to avoid a supply-demand gap. The article concludes with an analysis of the implications for the future of the global gas and LNG markets.

The Life Cycle Analysis (LCA) was used to assess the impact of biomethane plant of the “La Católica” in Pedregal-Majes-Arequipa farm, fed with cow manure and holding a production of 60 Nm3/day of purified biogas. Life cycle inventory, impact assessment and interpretation were performed. The functional unit established was 1 MJ of energy produced; the study was modeled with SimaPro software, Ecoinvent Database and ReCiPe Midpoint (H) impact assessment methodology, according to the impact categories of climate change and fossil resource depletion. The impact analysis was limited to the Well to Tank (WTT) approach, which involves feedstock transport, substrate mixed, anaerobic digestion, biogas purification, storage and injection of the fuel into transport vehicles. The digestion process generated the highest amount of CO2 emissions (1.79E-02 kg CO2 eq/MJ-biomethane) and the highest depletion of fossil resources (6.58E-03 kg oil eq/MJ-biomethane), compared to the other fuel production, due to energy consumption and transport infrastructure. Biomethane was then compared to fossil fuels, resulting in natural gas generating the least amount of CO2 emissions, followed by diesel and finally biomethane. For the fossil resource depletion category, biomethane presented the lowest amount of fossil fuel consumption (1.37E-02 kg oil eq/MJ-biomethane), followed by natural gas and diesel.

Chemical analysis of the organic components in beers has applications to quality control, authenticity and improvements to the flavor characteristics and brewing process. This study aims to show the complementary nature of two instrumental techniques which in combination can identify and quantify the majority of organic components in a beer sample. Nuclear Magnetic Resonance (NMR) was used to provide concentrations of twenty five different organic compounds including alcohols, organic acids, carbohydrates, and amino acids. Calorie content was also estimated for the samples. NMR data for ethanol concentrations were validated by comparison to a Fourier Transform Infrared Spectrometry (FTIR) method. Headspace Solid-Phase Microextraction (SPME) Gas Chromatography Mass Spectrometry (GCMS) was used to identify a range of volatile compounds such as alcohols, esters and hop derived aroma compounds. A simple and inexpensive conversion of a Gas Chromatography Flame Ionization Detector (GC FID) instrument to allow the use of Solid-Phase Microextraction was found to be useful for the quantification of volatile esters.

The versatility of metal complexes of corroles raised the interest in the use of these molecules as element of chemical sensors. The tuning of the macrocycle properties by synthetic modification of the different components of the corrole ring, such as functional groups, molecular skeleton, and coordinated metal, allows the creation of a vast library of corrole-based sensors. However, the scarce conductivity of most of aggregates of corroles limits the development of simple conductometric sensors and requires the use of optical or mass transducers that are rather more cumbersome and less prone to be integrated in microelectronics systems. To compensate the scarce conductivity, corroles are often used to functionalize the surface of conductive materials such as graphene oxide, carbon nanotubes, or conductive polymers. Alternatively, they can be incorporated in heterojunction devices where they are interfaced with a conductive material such as a phthalocyanine. Herewith, we introduce two heterojunction sensors made of junctions of lutetium bisphthalocyanine (LuPc2) with either 5,10,15-tris(pentafluorophenyl) corrolato Cu (1) or 5,10,15-tris(4-methoxyphenyl)corrolato Cu (2). Optical spectra show that after forming the heterojunction, corroles maintain their original structure. The conductivity of the devices reveals an energy barrier for interfacial charge transport, which is larger in the 1/LuPc2 device. The different interfacial barriers is also manifested by the opposite response respect to ammonia: with a 1/LuPc2 behaving as a n-type conductor and 2/LuPC2 as a p-type conductor. Furthermore, the sensors show a high sensitivity respect to relative humidity with a reversible and fast response in the range 30-60%.

The paper presents the results of modeling the problem of injecting liquid sulfur dioxide into a porous reservoir initially saturated with methane and ice. The model presented in the paper assumes the formation of three different regions, namely, the near one, saturated with liquid SO2 and its hydrate; the far one, containing methane and ice, and the intermediate one, saturated with methane and water. The effects of various parameters of the porous medium and injected SO2 on the nature of the course of the hydrate formation process have been studied. It is shown that with a decrease in reservoir permeability or injection pressure, the length of the intermediate region decreases, which in the limiting case means the formation of SO2 hydrate in the mode without the formation of an extended region saturated with methane and water. It is shown that such a regime is also typical for the case of high initial injection pressures, as well as low values of the initial reservoir temperature and injection temperature.

Three polyimides and six inorganic fillers in a form of nanometer-sized particles were studied as thick film solution cast mixed matrix membranes (MMMs) for transport of CO₂, CH₄ and H₂O. Gas transport properties and electron microscopy images indicate good polymer-filler compatibility for all membranes. The only filler type which demonstrated good distribution throughout the membrane thickness at 10 wt. % loading was BaCe_0.2Zr_0.7Y_0.1O₃ (BCZY). The influence of this filler on MMM gas transport properties was studied in detail for 6FDA-6FpDA in a filler content range from 1 to 20 wt.% and for Matrimid^® and P84^® at 10 wt. % loading. The most promising result was obtained for Matrimid^® - 10wt% BCZY MMM, which showed improvement in CO₂ and H₂O permeabilities accompanied by increased CO₂/CH₄ selectivity and high water selective membrane at elevated temperatures without H₂O/permanent gas selectivity loss.

Understanding the impact of drought stress on Arabica coffee physiology and metabolism is essential in the pursuit of developing drought-resistant varieties. In this study, we explored the physiological and metabolite changes in coffee genotypes exhibiting varying degrees of tolerance to drought—namely, the relatively tolerant Ca74110 and Ca74112, and the sensitive Ca754 and CaJ-19—under well-watered conditions and during terminal drought stress periods over two-time intervals (0 and 60 days following the onset of stress). The Metabolites profiling conducted uncovered significant associations between growth and the physiological characteristics of coffee genotypes with distinct drought tolerance behaviors. Initially, no marked differences were observed among genotypes or treatments. However, at the 60-day post-drought onset, notable increases in shoot growth, biomass, CO2 assimilation, pigments, and various physiological parameters were evident, particularly in the relatively tolerant genotypes. Metabolite profiling revealed elevations in glucose, maltose, amino acids, organic acids, and decreases in other metabolites, more pronounced in drought-tolerant genotypes. These alterations were more pronounced in the drought-tolerant genotypes, indicating a correlation with enhanced compatible solutes and energy-associated metabolites crucial for drought tolerance mechanisms. This research introduces GC-MS based metabolome profiling to Ethiopian coffee, shedding light on the intricate responses to drought stress and paving the way for the potential development of drought-resistant coffee seedlings in intensified agro-ecological zones.

To meet the International Maritime Organization’s requirements for carbon dioxide emissions from ships, a cost-effective and practical ship decarbonization tower was autonomously designed based on the marine diesel engine model 6135G128ZCa. The tower is internally filled with structured packing, and a slot-type liquid distributor at the top of the packing evenly distributes the NaOH solution to absorb carbon dioxide from the ship’s exhaust gas. Experimental research was conducted to investigate the influence of factors such as liquid-to-gas ratio and NaOH concentration on the performance of the decarbonization tower. The results confirmed that the use of NaOH solution can effectively absorb CO2 from ship exhaust gas, reducing CO2 emissions by more than 81.59% and meeting the EEDI (Energy Efficiency Design Index) requirements specified by the IMO.

Selecting drought-tolerant and more water-efficient wheat genotypes is a research priority, spe-cifically in regions with irregular rainfall or areas where climate change is expected to result in reduced water availability. The objective of this work was to use high-throughput measurements with morphophysiological traits to characterize wheat genotypes in relation to water stress. Field experiments were conducted from May to September 2018 and 2019, using a sprinkler bar irriga-tion system to control water availability to eighteen wheat genotypes: BRS 254; BRS 264; CPAC 01019; CPAC 01047; CPAC 07258; CPAC 08318; CPAC 9110; BRS 394 (irrigated biotypes) and Aliança; BR 18_Terena; BRS 404; MGS Brilhante; PF 020037; PF 020062; PF 120337; PF 100368; PF 080492; TBIO Sintonia (rainfed biotypes). The water regimes varied from 22 to 100% of the crop evapotranspiration replacement. Water stress negatively affected gas exchange, vegetation indices and grain yield. High throughput variables TCARI, NDVI, OSAVI, SAVI, PRI, NDRE and GNDVI had higher correlation with yield and morphophysiological measurements. The drought re-sistance index indicated that genotypes Aliança BRS 254, BRS 404, CPAC 01019, PF 020062, and PF 080492 were more drought tolerant.

Several sun models suggest the radioactive balance where the concentration of greenhouse gases and the albedo effect are related to the Earth's surface temperature. There is a considerable increment of greenhouse gases due to anthropogenic activities. Climate change correlates with this alteration in the atmosphere and an increase in surface temperature. Efficient forecasting of climate change and its impacts of 1.5°C global warming above pre-industrial levels could be helpful to respond to the threat of c.c. and develop sustainably. Many studies have predicted the temperature change in the coming years. The global community has to create a model that can realize good predictions to ensure the best way to deal with the warming. Thus, we propose a finite-time thermodynamic (FTT) approach in the present work. The FTT can solve problems such as the faint young sun paradox. In addition, we use different machine learning models to evaluate our method and compare the experimental prediction and results.

Tackling global warming and the consequent climate change in our planet is of urgent importance to our society. Renewable biomass derived carbons have been studied as promising adsorbents, but marine biomass derived carbons have not been explored extensively. S and N double-doped porous carbons were obtained from a marine biomass related precursor. Adding carbon nanoparticles (CNP) graphene oxide (GO), or carbon nanotubes (CNTs), in an early stage of the synthesis leads to a modified porous texture and surface chemistry. The carbons retained 2-4.5 at% nitrogen and 1.1 at% sulfur. The best GO and CNT added carbons had an apparent surface area 1780 m2/g and 1170 m2/g, respectively, compared to 1070 m2/g of the CNP-free matrix. The Dubinin-Radushkevich (DR) and Henry models were used to assess the strength of the interactions between various gases and the surface. The N2/H2 and CO2/CH4 selectivities were estimated with ideal adsorbed solution theory (IAST). While the CNPs, particularly GO, had a remarkable effect both on the porous texture and the surface chemistry, their influence on selectivity is more modest.

The offshore oil and gas working environment is an inherently dangerous one, with risks posed to physical safety on a daily basis. One neglected field of research is the added psychosocial stressors present in this environment. This research examined the experiences of offshore oil and gas workers through one-on-one online interviews which were recorded and transcribed. Transcripts were analysed through qualitative software NVivo, which generated themes and patterns for the responses given to questions which were developed through a focus group. The results of the analysis showed that multiple psychosocial stressors are present for this population, such as fear of speaking up, unsatisfactory company-provided facilities, work-life interference, work status, micromanaging, gender harassment and bullying. In addition, interviews identified that production and time pressures along with fatigue can influence accidents and mistakes. Climate factors also cause discomfort, however these are managed according to best practice by organisations. Due to the timing of the study, COVID-19 was a significant stressor for some, but not all, employees. In conclusion, offshore oil and gas workers face multiple stressors in a dangerous environment that may lead to devastating consequences.

In offshore drilling, accidents such as gas invasion, overflow, and kicks are inevitable, and they can escalate into blowouts and other catastrophic events that result in casualties and substantial economic losses. Therefore, maintaining drilling safety requires accurate monitoring of gas invasion and overflow. The majority of overflow monitoring methods currently utilized at drilling sites are threshold-based. However, monitoring parameters acquired during actual drilling operations frequently contain noise signals, making it difficult for threshold-based methods to strike a balance between improving accuracy and minimizing false positives. In this paper, Pattern Recognition-based Kick Detection (PRKD) is proposed as a novel method for diagnosing overflow in offshore drilling. This method utilizes the overflow evolution process by integrating multi-phase flow calculations, data filtering theory, pattern recognition theory, the Bayesian framework, and other theoretical models. The PRKD effectively detects and monitors gas intrusion and overflow based on single parameters by analyzing the shape and wave characteristics of the curves. The case analysis demonstrates that the proposed method for monitoring drilling overflow achieves high precision while maintaining a low false positive rate. By combining advanced computational techniques with pattern recognition algorithms, the PRKD improves the accuracy and reliability of kick detection, enabling proactive responses to potential risks, protecting the environment and human lives, and optimizing drilling operations.

This work presents the dynamics of forest clearing in the Brazilian Amazon during the period 2006–2019 in which includes the approval of the new Brazilian Forest Code in 2012. The study was carried out in the Brazilian Amazon, Pará State and in the municipality of Novo Progresso (Pará State). The analysis was based on deforestation and fire hotspot datasets issued by the Brazilian Institute for Space Research (INPE), produced based on optical and thermal sensors onboard different satellites. Deforestation data was also used to assess greenhouse gas (GHG) emissions from the slash-and-burn practices. The work showed a good correlation between the occurrence of fires in the newly deforested area in the municipality of Novo Progresso and the slash-and-burn practices. The same trend was also observed in the Pará State, suggesting a common practice along the deforestation arch. The study indicated positive coefficients of determination of 0.72 and 0.66 between deforestation and fire occurrences for the municipality of Novo Progresso and Pará State, respectively. The increased number of fire occurrences in the primary forest suggests possible ecosystem degradation. Deforestation reported for 2019 surpassed 10,000 km2, a significant intensification comparatively higher than the previous ten years which was on an average of 6,760 km2. The steady increase of deforestation in the Amazon after 2012 has been a worldwide concern because of the forest loss itself as well as the massive GHG emitted in the Brazilian Amazon (295 million tons of net CO2 equivalent in the year 2019). Better correlation of deforestation and fires occurrences reported from satellite images confirmed the slash-and-burn practice and the secondary effect of deforestation, which degrades primary forest surrounding the deforested areas.

Leaf temperature (T_leaf) influences photosynthesis and respiration. Currently, there is a growing interest on including lianas in productivity models due to their increasing abundance, and their detrimental effects on net primary productivity in tropical environments. Therefore, understanding the differences of T_leaf between lianas and trees is important for future of forest on whole ecosystem productivity. Here we determined the displayed leaf temperature (T_d= T_leaf – ambient temperature) of several species of lianas and their host trees during ENSO and non-ENSO years to evaluate if the presence of lianas affects the T_d of their host trees, and if leaves of lianas and their host trees exhibit differences in T_d. Our results suggest that close to midday, the presence of lianas does not affect the T_d of their host trees; however, lianas tend to have higher values of T_d than their hosts across seasons, in both ENSO and non-ENSO years. Although lianas and trees tend to have similar physiological-temperature responses, differences in T_d could lead to significant differences in rates of photosynthesis and respiration based temperature response curves. Future models should thus consider differences in leaf temperature between these life forms to achieve robust predictions of productivity.

Multinuclear NMR studies of the gaseous mixtures that involve volatile compounds and ³He atoms are featured in this review. Precise analyses of the ³He and other nuclei resonance frequencies show linear dependences on the gas density. Extrapolation of the gas phase results to the zero-pressure limit gives ν₀(³He) and ν₀(ⁿX) resonance frequencies of nuclei in a single 3-helium atom and nuclei in molecules at a given temperature. The NMR frequency comparison method provides an approach for determining different nuclear magnetic moments. Application of quantum chemical shielding calculations which include a more complete and careful theoretical treatment allows the shielding of isolated molecules to be achieved with great accuracy and precision. They are used for evaluation of nuclear moments without shielding impact on bare nuclei: ^10/11B, ¹³C, ¹⁴N, ¹⁷O, ¹⁹F, ²¹Ne, ²⁹Si, ³¹P, ³³S, ^35/37Cl, ³³S , ⁸³Kr, ^129/131Xe, and ¹⁸³W. On the other hand, new results of nuclear moments were used for reevaluation of absolute nuclear magnetic shielding in molecules under study. Additionally, ³He gas in water solutions of lithium and sodium salts was used for measurements of ^6/7Li and ²³Na magnetic moments and reevaluation of shielding parameters of Li⁺ and Na⁺ water solvated cations. In this paper, guest ³He atoms that play a role in probing the electron density in many host macromolecules are presented as well.

In this field pot study, effect of drainage method (e.g., intermittent drainage (ID) and continuous flooding (CF)) on greenhouse gas (GHGs: CO2 and CH4) emission was determined from three Korean paddies (BG, MG, and JS series), varying soil properties such as soil texture, labile carbon, and mineral types. Emission of GHGs was evidently influenced by the irrigation, to a different extent, depending on paddy’s redox (Eh) shift upon flooding events. The Eh decline upon flooding was slower in JS pot, where pore-water concentration of ferric and sulfate ions is the highest (~ up to 3-fold) among three paddies. MG pot was 2- to 3-fold percolative than others and the Eh drop during flooding period was the smallest (staying above -50 mV). In ID treatment, CH4 emission (t CO2-eq ha-1 yr-1) was reduced in a wide range by 5.6 for JS pot, 2.08 for BG pot, and 0.29 for MG pot relative to CF, whereas CO2 emissions (t CO2-eq ha-1 yr-1) was increased by 1.25 for JS pot, 1.07 for BG pot, and 0.48 for MG pot due to the enhanced oxidation of labile carbon. Grain yield and aboveground biomass production from ID were no less than those from CF (p &lt; 0.05). Consequently, gain of global warming potential (S GWP) by ID varied as the order of JS (37%) &gt; BG (14%) &gt; MG (~0 %) pots, and negligible effect observed for MG pot is due to the equivalent trade-off between CO2 and CH4. Our findings suggest that the efficacy of ID practice on GHGs emission can be further improved by the consideration of redox response of paddy system.

Switzerland, a wealthy country, has a cutting-edge healthcare system, yet per capita, it emits over one ton of CO2, ranking among the world's most polluting healthcare systems. To estimate the carbon footprint of the healthcare system of Geneva’s canton, we collected raw data on the activities of its stakeholders. Our analysis shows that when excluding medicines and medical devices hospitals are the main greenhouse gas emitter by far, accounting for 48% of the healthcare system’s emission, followed by nursing homes (20%), private practice (18%), analysis laboratories (7%), dispensing pharmacies (4%), the homecare institution (3%) and the ambulance services (

A Natural gas is increasingly being sought after as a vital source of energy, given that its production is very cheap and does not cause the same environmental harms that other resources, such as coal combustion, do. Understanding and characterizing the behavior of natural gas is essential in hydrocarbon reservoir engineering, natural gas transport, and process. Natural gas compressibility factor, as a critical parameter, defines the compression and expansion characteristics of natural gas under different conditions. In this study, a simple second-order polynomial model based on the group method of data handling (GMDH) is presented to determine the compressibility factor of different natural gases at different conditions, using corresponding state principles. The accuracy of the model evaluated through graphical and statistical analyses. The results show that the model is capable of predicting natural gas compressibility with an average absolute error of only 2.88%, a root means square of 0.03, and a regression coefficient of 0.92. The performance of the developed model compared to widely known, previously published equations of state (EOSs) and correlations, and the precision of the results demonstrates its superiority over all other correlations and EOSs.

For the past few decades, researchers have been intrigued with glassy polymers, which have applications ranging from gas separations to corrosion protection to drug delivery systems. The techniques employed to examine the sorption and diffusion of small molecules in glassy polymers are the subject of this review. Diffusion models in glassy polymers are regulated by Fickian and non-Fickian diffusion, with non-Fickian diffusion being more prevalent. The characteristics of glassy polymers are determined by sorption isotherms, and different models have been proposed in the literature to explain sorption in glassy polymers during the last few years. This review also includes the applications of glassy polymer. Despite having so many applications, current researchers still have difficulty in implementing coating challenges due to issues like as physical ageing, which is briefly discussed in the review.

The opportunities and advantages of implementing Artificial Intelligence (AI) and Machine Learning (ML) to optimize the process control of wastewater treatment in the Oil and Gas industry are discussed in this work. Discussion is centered around five major points: 1) Various types of Oil and Gas wastewater (Sour, Oily, Produced) and industry standards/methods for treatment, including specific case studies and challenges when treating certain wastewater. This section aims at the common types of wastewater in the Oil and Gas industry and how they are generally treated. 2) How AI/ML has been implemented in wastewater treatment in various industries; summary of which AI/ML languages were used along with a brief overview of how they work. This article focused on an understanding of the specific case studies and AI explanations to understand the effectiveness of wastewater treatment using AI/ML. 3) AI that is currently implemented in Oil and Gas such as personal protective equipment (PPE), smartwatches radiofrequency identification etc. This showed that AI/ML already plays a successful role in the Oil and Gas industry and has proven to help optimize many processes and components. Many of these AI/ML implementations are now industry standards and have greatly benefitted the industry. This section demonstrates that the implementation and the use of AI/ML have been proven to be a successful endeavor and that expanding the role of AI/ML would be beneficial. 5) Using the established points from the previous sections the paper outlines why AI/ML is ideal for Oil and Gas wastewater treatment; this argument centers around fit-for-purpose treatment, and the possible uses of the treated water. A determination of the best-suited AI languages, possible implementation scenarios, and how this would shift the way Oil and Gas industries treat and approach wastewater is presented to the reader.

To study the oil and gas distribution law in the slope area of the hydrocarbon-bearing basin, the distribution of the effective dominant path of sand bodies transporting oil and gas is a fundamental subject. In this paper, we introduced an effective way to predict such transport paths and applied the method to study the sand bodies of the lower first member of the Shahejie Formation (E3s1L) in the southern area of the Qikou Depression in the Bohai Bay Basin (Qinan). We first define the dominant hydrocarbon transport paths of the sand body as the superimposed area of the contiguously distributed area of the sand body and the paleotectonic ridges at the top of the formation where the sand body is located. Then we define the oil and gas supply area of the oil source fault as the overlapped area of the favorable transport path of oil source faults and the width of the associated fracture zone. Stacking the two areas, we can delineate the distribution of the effective dominant transport paths of the sand bodies. The results from our case study of the Qinan area show that the effective dominant paths of sand bodies transporting oil and gas in the E3s1L Formation in the Qinan area are distributed throughout the region with better development in the west than in the east. The paths in the eastern part extend from north to south, while the paths in the western part extend from northeast to southwest, which is favorable for the convergence of oil and gas generated from the source rocks of the third member of Shahejie Formation (Es3) in the Northeastern main depression of Qikou and the formation of oil and gas accumulations in the l E3s1L Formation. The results are consistent with the fact that oil and gas discovered in the E3s1L Formation in the Qinan region are mainly distributed in the central and western regions, with a small amount in the southeast. Therefore, the suggested method is feasible to predict the effective dominant path of sand bodies transporting oil and gas.

Thermoelectric (TE) waste heat recovery has attracted significant attention over the past decades, owing to its direct heat-to-electricity conversion capability and reliable operation. However, methods of system-level TE design optimization for specific application systems have not been thoroughly investigated. This work theoretically studies the performance optimization and exergy analysis of TE systems for recovering waste heat from the exhaust ducts of a gas turbine power plant. A numerical tool has been developed to solve the coupled charge and heat current equations with temperature-dependent material properties and convective heat transfer at the interfaces. Our calculations show that at the optimum design with 50 % fill factor and 6-mm leg thickness made of state-of-the-art Bi2Te3 alloys, the proposed system can reach power output of 10.5 kW for the TE system attached on a 2 m-long, 0.5 x 0.5 m2-area exhaust duct with system efficiency of 5 % and material cost per power of 0.23 $/W. Moreover, our extensive exergy analysis reveals that only 1 % of the exergy content of the exhaust gas is exploited in this heat recovery process and the exergy efficiency of the TE system can reach 8 % with improvement potential of 85 %.

Due to their excellent physicochemical properties, fluorinated greenhouse gases (F-gases), including hydrofluorocarbons (HFCs), perfluorocarbons (PFCs), sulfur hexafluoride (SF6), and nitrogen trifluoride (NF3), are used in a variety of applications, but they are potent greenhouse gases. Therefore, they have been blanketed into the list of phase-out under the international protocols or treaties. In this work, the updated statistics of the Taiwan’s national inventory report (NIR) were used to analyze the trends of F-gases (i.e., HFCs, PFCs, SF6 and NF3) emissions during the period of 2000-2020. Furthermore, the regulatory strategies and measures for reducing the emissions of the four F-gases will be summarized to be in accordance with the national and international regulations. With the progressive efforts by the regulatory requirements and the industry’s voluntary reduction, the total F-gases emissions indicated a significant increase from 2,462 kilotons of carbon dioxide equivalents (CO2eq) in 2000 to the peak value (i.e., 12,643 kilotons) of CO2eq in 2004, but sharply decreased from 10,284 kilotons of CO2eq in 2005 to 3,906 kilotons of CO2eq in 2020. It was also found that the most commonly used method for controlling the emissions of F-gases from the semiconductor and optoelectronic industries was based on the thermal destruction-local scrubbing technology.

There are many pollution and environment problem in the human ecosystem. There are different methods are used to removal of sulfur from sour gases for example Basic Claus process and Modified Claus process . There are different chemical software are used for simulation and optimization of Claus process for example Aspen Plus and Chemcad ECT. The Gibbs free energy method is introduced and model of Claus process. There are new parameter are introduced in reaction furnace to reduce the error from 33% to 7 %. The waste heat boiler is installed at the reaction furnace in which high pressure stream is produced and study the decomposition the hydrogen sulphide. The new rate of reaction is introduced of the enhancement of H2 production in chemical process. The simulation of reaction furnace in Aspen plus software is the maximum utilization of process. Due to suitable operating condition of reaction furnace is caused the maximum destruction of ammonia gas in the reactor. When we are increasing the oxygen concentration and temperature of feed is causing decreasing the ammonia production in reaction furnace. It is below than acceptance value of ammonia is 150 ppm in the reaction furnace. The presence of oxygen components, Sulfur oxide, hydroxide components are effect on decreasing the amount of ammonia in furnace and temperature is about at 1350⁰C. It is noted that when the production of sulfur recovery is decrease in Claus process and the production of carbon monoxide is increase in the thermal section at the existence. Now we are work on parametric studies of furnace that could be causes the production of ammonia destruction and CO emission in the Claus process. Due to optimize the reaction furnace parameter are help to get large of sulfur production, ammonia gas destruction, increased the catalyst life and decreased of dangerous gases.

Sorption of pure CO2 and CH4 and CO2/CH4 binary gas mixtures in amorphous glassy Poly(2,6-dimethyl-1,4-phenylene) oxide (PPO) at 35°C up to 1000 Torr is investigated. Sorption experiments were carried out using an approach that combines barometry with FTIR spectroscopy in the transmission mode to quantify the sorption of pure and mixed gases in polymers. The pressure range is chosen to prevent any variation of the glassy polymer density. The solubility within the polymer of the CO2 present in the gaseous binary mixtures is practically coincident with the solubility of pure gaseous CO2, up to a total pressure of the gaseous mixtures equal to 1000 Torr and for CO2 mole fraction of ~0.5 mol mol-1 and ~0.3 mol mol-1. The Non-Equilibrium Thermodynamics for Glassy Polymers (NET-GP) modelling approach has been applied to the Non-Random Hydrogen Bonding (NRHB) lattice fluid model to fit the solubility data of pure gases. We have assumed here that no specific interactions are occurring between the matrix and the absorbed gas. The same thermodynamic approach has been then used to predict the solubility of CO2/CH4 mixed gases in PPO resulting in a deviation lower than 9.5% from the experimental results for CO2 solubility.

Radon (²²²Rn) is the second most common type of lung cancer after smoking. As radon poses a significant risk to human health, radon-affected areas should be to ensure people’s awareness of risk and remediation. The primary goal of this research was to investigate the local natural radioactivity (in soils, water and indoors) because of the presence of tuff outcrops (from middle lower Pleistocene volcanic activity) that naturally produce radioactive gas radon at Cerveteri (Rome, Central Italy). The study area is characterized by the presence of several funerary sites pertaining to the Etruscan Necropolis of Cerveteri, which extends over a volcanic rock plateau. The results of the radon survey highlighted moderate (>16000 Bq/m³) but localized anomalies in soils and medium low (< 200 Bq/m³) values of indoor radon excepting some cases exceeding the threshold (> 300 Bq/m³) recommended by 2013/59 Euratom Directive. Although for thoron (²²⁰Rn) effects on human health, there exist no clinical data, the study of ²²⁰Rn average activity concentration in the soil gas survey has revealed new insights for the interpretation of radon sources that can affect dwellings, even taking into account the considerable difference in the half-lives of the ²²²Rn and ²²⁰Rn.

We present a generic and open-source framework for the numerical modeling of the expected transport and storage mechanisms in unconventional gas reservoirs. These unconventional reservoirs typically contain natural fractures at multiple scales. Considering the importance of these fractures in shale gas production, we perform a rigorous study on the accuracy of different fracture models. The framework is validated against an industrial simulator and is used to perform a history-matching study on the Barnett shale. This work presents an open-source code that leverages cutting-edge numerical modeling capabilities like automatic differentiation, stochastic fracture modeling, multi-continuum modeling and other explicit and discrete fracture models. We modified the conventional mass balance equation to account for the physical mechanisms that are unique to organic-rich source rocks. Some of these include the use of an adsorption isotherm, a dynamic permeability-correction function, and an embedded discrete fracture model (EDFM) with fracture-well connectivity. We explore the accuracy of the EDFM for modeling hydraulically-fractured shale-gas wells, which could be connected to natural fractures of finite or infinite conductivity, and could deform during production. Simulation results indicates that although the EDFM provides a computationally efficient model for describing flow in natural and hydraulic fractures, it could be inaccurate under these three conditions: 1. when the fracture conductivity is very low. 2. when the fractures are not orthogonal to the underlying Cartesian grid blocks, and 3. when sharp pressure drops occur in large grid blocks with insufficient mesh refinement. Each of these results are very significant considering that most of the fluids in these ultra-low matrix permeability reservoirs get produced through the interconnected natural fractures, which are expected to have very low fracture conductivities. We also expect sharp pressure drops near the fractures in these shale gas reservoirs, and it is very unrealistic to expect the hydraulic fractures or complex fracture networks to be orthogonal to any structured grid. In conclusion, this paper presents an open-source numerical framework to facilitate the modeling of the expected physical mechanisms in shale-gas reservoirs. The code was validated against published results and a commercial simulator. We also performed a history-matching study on a naturally-fractured Barnett shale-gas well considering adsorption, gas slippage & diffusion and fracture closure as well as proppant embedment, using the framework presented. This work provides the first open-source code that can be used to facilitate the modeling and optimization of fractured shale-gas reservoirs. To provide the numerical flexibility to accurately model stochastic natural fractures that are connected to hydraulically-fractured wells, it is built atop other related open-source codes. We also present the first rigorous study on the accuracy of using EDFM to model both hydraulic fractures and natural fractures that may or may not be interconnected.

Culture systems for 3-dimensional tissues, such as multicellular spheroids, are indispensable for high-throughput screening of primary or patient-derived xenograft (PDX)-expanded cancer tissues. Oxygen supply to the center of such spheroids is particularly critical for maintaining cellular functions as well as avoiding the development of a necrotic core. In this study, we evaluated 2 methods to enhance oxygen supply: (1) using culture plate with gas-permeable polydimethylsiloxane (PDMS) membrane at its bottom and (2) embedding hydrogel beads in the spheroids. Culturing spheroids on PDMS increased cell growth and affected glucose/lactate metabolism and CYP3A4 mRNA expression and subsequent enzyme activity. The spheroids comprised 5000 Hep G2 cells and 5000 20 µm-diameter hydrogel beads did not develop a necrotic core for 9 days when cultured on a gas-permeable sheet. In contrast, central necrosis in spheroids lacking hydrogel beads was observed after day 3 of culture, even when using PDMS. These results indicate that the combination of gas-permeable culture equipment and embedded hydrogel beads improves culture 3D spheroids produced from primary or PDX-expanded tumor cells.

Large amounts of gas hydrate are present in marine sediments offshore Taitao Peninsula, near the Chile Triple Junction. Here, marine sediments on the forearc contain carbon that is converted to methane in a zone of very high heat flow and intense rock deformation above the downgoing oceanic spreading ridge separating the Nazca and Antarctic plates. This regime enables vigorous fluid migration. Here we present an analysis of the spatial distribution, concentration, estimate of gas phases (gas hydrate and free gas) and geothermal gradients in the accretionary prism and forearc sediments offshore Taitao (45.5° - 47° S). Velocity analysis of Seismic Profile RC2901-751 indicates gas hydrate concentration values <10% of the total rock volume, and extremely high geothermal gradients (<190 °Ckm^-1). Gas hydrates are located in shallow sediments (90-280 meters below the seafloor). The large amount of hydrate and free gas estimated (7.21x10¹¹ m³ and 4.1x10¹⁰ m³, respectively), the high seismicity, the mechanically unstable nature of the sediments, and the anomalous geothermal conditions, set the stage for potential massive releases of methane to the ocean mainly through hydrate dissociation and/or migration directly to the seabed through faults. We conclude that the Chile Triple Junction is an important methane seepage area and should be the focus of novel geological and ecological research.

This paper deals with the techno-economic study of the hybrid renewable energy system based on energy storage aspect under the form of hydrogen and methane. Indeed, with the intermittency of the renewable energy sources such as photovoltaic and wind energy, several problems of produced energy injection to the power system network can be encountered due to the shortage or the excess of these sources. This situation appeals the use of systems that ensure the stability of network based on the storage of energy surplus into gas using electrolyzer systems, which will be used afterward to cover the eventual shortage. In the present paper, the study of performance of each pathway of methane and hydrogen storage has been performed by the treatment of multiple scenarios via different architecture case studies in an Algerian location. Whereas, the energy produced by the photovoltaic system, the wind energy and the gas micro turbine sources are considered similar in each case. The modeling and simulation of the studied system operation under optimization criteria has been performed in this work, where the main aim is to define the appropriate configuration taking into account the different with low costs of investment, maintenance operation and immediate reactivity with a big storage capacity.

We show that the van der Waals gas does not exhibit just the celebrated liquid-gas 1 transition but also a quantum-classical one. We study the issue with reference to the LMC statistical 2 complexity and in relation to the order-disorder contrast.

Salvia ceratophylloides (Ard.) is an endemic, rare, threatened plant species recently rediscovered in very few individuals in two different sites of South Italy. The study of within-plant variation more than among-plant one is fundamental to understand the plant adaptation to the local conditions, especially in rare species, and consequently to preserve plant biodiversity. Here, we reported the variation of the morpho-ecophysiological and metabolic traits between the sessile and petiolate leaf of S. ceratophylloides plants in two different sites for understanding the adaptation strategies for surviving in these habitats. The S. ceratophylloides individuals exhibited different net photosynthetic rate, maximum quantum yield, light intensity for the saturation of the photosynthetic machinery, stomatal conductance, transpiration rate, leaf area, fractal dimension and some VOCs between the different leaf types. This within-plant morpho-physiological and metabolic variation was depended on the site. These results provide empirical evidence of sharply within-plant variation of the morpho-physiological traits and VOCs profiles in S. ceratophylloides which could be because of adaptation to the local conditions.

Cellulose-based carbon (CBC) has been widely concerned with its porous structure, high specific surface area, and is liable to adsorb gas molecules and macromolecular pollutants. However, the application of CBC in gas sensing has been little studied. In this paper, ZnO/CBC heterojunction was formed by means of simple co-precipitation and high temperature carbonization. As a new ammonia sensor, the prepared ZnO/CBC sensor can detect ammonia compared with that of the previous pure ZnO ammonia sensor can not at room temperature. It has great gas sensing response, stability and selectivity to ammonia concentration at 200 ppm. This study provides a new idea for the design and synthesis of biomass carbon-metal oxide composites.

Methane is the main cause of sewer explosion accidents, and the available monitoring methods mainly use portable gas sensors for on-site detection. However, these methods cannot grasp the dynamic changes in methane in a sewer in real time or make better predictions of methane explosion accidents. Here, we present a low-power online monitoring system for sewer methane in order to ensure the safety of urban sewers. A low-power ultrasonic gas sensor was used to monitor the methane content in biogas. Due to the impacts of changes in CO2, temperature, and humidity in the sewer on the ultrasonic methane measurement results, a corresponding compensation method was proposed. The effectiveness of the compensation method was verified through experiments, which measured the methane concentration under different influences, and the methane values measured before and after compensation were compared. The power consumption was only 1.28 mW if the system worked in intermittent operation mode, and it could operate for about 1.5 years by selecting a lithium battery with a capacity of 5 A · H. The experimental results showed that the gas detection accuracy could meet the commercial requirements and had a high compensation for the impacts of carbon dioxide, temperature, and humidity.

This investigation was conducted to determine the chemical composition and nutritional value of five plant species commonly used as ruminant feeds namely: Artemisia herba-alba, Acer monspessulanum, Amygdalus lycoides, Amygdalus scoparia, and Atriplex leucoclada. After the collecting samples, the chemical compositions of plants included dry matter (DM), organic matter (OM), crude protein (CP), ether extract (EE), ash (CA), cell wall (NDF), and non-lignin cell wall (ADF) were determined according to standard methods. For degradation testing, the nylon bag technique was applied using three native Sistani fistula calves. Organic matter digestibility (OMD) and metabolisable energy (ME) were determined through the gas production technique. The CP value ranged from 5.30 (Amygdalus scoparia) to 11.72% (Atriplex leucoclada) while NDF value ranged from 52.62 (Amygdalus lycoides) to 69.05% (Amygdalus scoparia). The range of OMD, DOMD, and ME was from 36.67 to 53.27%, 34.67 to 49.11%, and 5.57 to 8.08 (MJ/kg), respectively. The results showed a positive correlation between cell wall composition and dry matter digestibility in plant species. The nutritional value of Amygdalus lycoides, Atriplex leucoclada, Acer monspessulanum, and Artemisia herba-alba was acceptable composition and digestibility.

Background: Qazvin province has suffered a lot of natural disasters (earthquakes) for a long time. so, the establishment of the first industrial city in Iran, has always been a source of concern. One of these problems is the possibility of chlorine gas leaking from the chlorination system of drinking water and treatment plant the existing ones are on the health of the inhabitants of this region.Material and method: This analytical study was carried out in Novorossiysk district of Alborz in December 2012. Initially, chlorine gas leakage scenarios from these facilities were simulated by ALOHA and WISER software, and then using the Emergency Level System, according to the CCPS Consultative Center's Chemical Process Safety Advice, the Emergency Response Program was presented. Results: ALOHA software, in comparison with WISER software, has more precision to identify and address the consequences of chlorine gas leakage hazards and according to the simulation of this software in the event of a leak from the well and water resources unit at 8240 m from the area and at night 7520 meters will be affected. Due to the speed of delivering results through the WISER software, this software can be used at times when the operating speed is considered (incident time).Conclusion: According to the CCPS model, the emergency conditions were classified at levels 3 and 4, therefore, the relevant crisis management agencies (Qazvin Crisis Management Committee, Alborz City Health Center, Red Crescent and Firefighting Authority) should provide training maneuvers At Alborz city level, and informing people of cities and industrial companies, many efforts have been made to reduce human and environmental damage in case of possible leakage.

The aim of the study was to examine the biogas and methane yield of maize silage, a wastes in agricultural point of view and compare it to the biogas productivity of commonly used mixture of maize silage and mixed fodder with water. The experimental study was carried out into 2 parts. Firstly, the batch experiment was conducted in Mesophilic conditions (35°C), at five different hydraulic retention times (HRT): 6 DAT, 11 DAT 20 DAT 29 DAT and 41 DAT. The results revealed that maize silage was generated the highest biogas yield of 537 mL /241 mL at the HRT of 6days /41 days. Mixed fodder produced the highest biogas yield of 421 mL at the HRT of 6th days and the lowest one was 252 mL at the HRT of 20th days. Finally, the methane, carbon dioxide and hydrogen sulphide of biogas produced from maize silage and mixed fodder were analyzed using a gas chromatography. The results shown that biogas from maize silage precedes the gas less than the mixed fodder. In the field level experiment proved that from mixed fodder produced gas which would be enough for 7 member’s family used 3 months for the purpose of their cooking.

Gas membrane-based separation is considered one of the furthermost effective technology to address energy efficiency and large footprint challenges. Various classes of advanced materials including polymers, zeolites, porous carbons and metal–organic frameworks (MOFs) were attempted as membranes for gas separation. MOFs, among other porous materials, possess uniquely tunable nature, in which the pore size and environment can be controlled by connecting metal ions (or metal ion clusters) with organic linkers with various functionalities. This feature makes them attractive for thin membrane fabrication, as both diffusion and solubility components of permeability can be altered. It is interesting to notice that numerous reports have addressed the synthesis of different MOFs, fabrication of their corresponding thin films and their applications, nonetheless, relatively limited studies addressed their gas separation application as membranes. In this review, we provide a synopsis of the various MOF-based membranes that were fabricated in the last decade. In this review we propose a short introduction touching on the gas separation membrane technology and we shed light on (i) the various techniques developed for the fabrication of MOF as membranes and (ii) challenges and application for MOF thin film membranes in various important gas separation applications.

Due to failure of the continuum hypothesis for higher Knudsen numbers, rarefied gases and microflows of gases are particularly difficult to model. Macroscopic transport equations compete with particle methods, such as DSMC to find accurate solutions in the rarefied gas regime. Due to growing interest in micro flow applications, such as micro fuel cells, it is important to model and understand evaporation in this flow regime. Here, evaporation boundary conditions for the R13 equations, which are macroscopic transport equations with applicability in the rarefied gas regime, are derived. The new equations utilize Onsager relations, linear relations between thermodynamic fluxes and forces, with constant coefficients, that need to be determined. For this, the boundary conditions are fitted to DSMC data and compared to other R13 boundary conditions from kinetic theory and Navier-Stokes-Fourier (NSF) solutions for two one-dimensional steady-state problems. Overall, the suggested fittings of the new phenomenological boundary conditions show better agreement to DSMC than the alternative kinetic theory evaporation boundary conditions for R13. Furthermore, the new evaporation boundary conditions for R13 are implemented in a code for the numerical solution of complex, two-dimensional geometries and compared to NSF solutions. Different flow patterns between R13 and NSF for higher Knudsen numbers are observed.

The article discusses the validation process of a certain method of balancing gas contained in the pore space of rocks. The validation was based upon juxtaposition of the examination of rocks' porosity and the effects of comminution in terms of assessing the possibility of opening the pore space. The tests were carried out for six dolomite samples taken from different areas of the 'Polkowice-Sieroszowice’ copper mine in Poland. Before the rock material was ground, it was examined using the porosimetric method and subsequently subjected to the SEM analysis. After grinding, the research material was subjected to the granulometric analysis. Prior to the grinding process, the rocks' porosity fell in the range of 0.3-14.8%, while the volume of the open pores was included in the 0.01-0.06 cm3/g range. The research material was also characterized by inhomogeneous distribution of the pore volume. The grinding process was performed using an original device – the GPR analyzer. The ground samples were characterized by similar particle size distribution and mean diameters D_3.2 of about 4.0-4.5 µm. The SEM analysis revealed pores of various size and shape on the surface of the rock cores, while at the same time demonstrating lack of pores following the grinding process. The grain size distribution curves were compared with the cumulative pore volume curves of the cores before grinding. The resulting intersection points of both curves were seen as testifying to the presence of openings in the rock pores and release of the accumulated gas. The opening percentage of the pore space was associated with the coordinates of the curves' intersections. In order to confirm the argument put forward in this paper – i.e. that comminution of a rock to grains of a size comparable with the size of the rock's pores results in the release of gas contained in the pore space – the amount of gas released as a result of the comminution process was studied. The results of gas balancing demonstrated that the pore space of the investigated dolomites was filled with gas in amounts from 3.19 cm3/kg to 45.86 cm3/kg. The obtained results of the rock material comminution to grains comparable – in terms of size – to the size of the pores of investigated rocks, along with asserting the presence of gas in the pore space of the studied dolomites, were regarded as a proof that the method of balancing gas in rocks via rock comminution is correct.

The air in subterranean karst cavities is often depleted in methane (CH₄) relative to the atmosphere. Karst is considered a potential sink for the atmospheric greenhouse gas CH₄ because its subsurface drainage networks and solution-enlarged fractures facilitate atmospheric exchange. Karst landscapes cover about 14% of earth’s continental surface, but observations of CH₄ concentrations in cave air are limited to localized studies in Gibraltar, Spain, Indiana (USA), Vietnam, Australia, and by incomplete isotopic data. To test if karst is acting as a global CH₄ sink, we measured the CH₄ concentrations, δ¹³C_CH4, and δ²H_CH4 values of cave air from 33 caves in the USA and three caves in New Zealand. We also measured CO₂ concentrations, δ¹³C_CO2, and radon (Rn) concentrations to support CH₄ data interpretation by assessing cave air residence times and mixing processes. Among these caves, 35 exhibited subatmospheric CH₄ concentrations in at least one location compared to their local atmospheric backgrounds. CH₄ concentrations, δ¹³C_CH4, and δ²H_CH4 values suggest that microbial methanotrophy within caves is the primary CH₄ consumption mechanism. Only 5 locations from 3 caves showed elevated CH₄ concentrations compared to the atmospheric background and could be ascribed to local CH₄ sources from sewage and outgassing swamp water. Several associated δ¹³C_CH4 and δ²H_CH4 values point to carbonate reduction and acetate fermentation as biochemical pathways of limited methanogenesis in karst environments and suggest that these pathways occur in the environment over large spatial scales. Our data show that karst environments function as a global CH₄ sink.

Hyperbaric oxygen therapy (HBOT) is a well-established treatment for carbon monoxide (CO) poisoning. HBOT is performed in a hyperbaric chamber, which increases the atmosphere absolute (ATA) and oxygen concentration in the chamber. To ensure patient safety during HBOT, a gas monitoring system is used to monitor the oxygen levels, ATA, and other parameters. This study aims to perform the safety evaluation of the monoplace hyperbaric chamber compared to a gas monitoring system in the treatment of CO poisoning. In addition, it examined the clinical characteristics of the patients diagnosed with CO poisoning who performed HBOT. In the safety evaluation of the monoplace chamber, it was compared the values of oxygen (O2), carbon dioxide (CO2), humidity, and temperature were measured in the hyperbaric chamber and gas monitoring system when operating at 2.0 ATA and 3.0 ATA. Moreover, in the clinical characteristics of patients with CO poisoning who performed HBOT, 1,006 patients were analyzed by using the data registry. Under the condition at 3.0 ATA, the average CO2 was higher in the hyperbaric chamber than in the gas monitoring system (p&lt;0.001). Also, the average humidity was higher in the hyperbaric chamber than in the gas monitoring system (p=0.004). Under the condition at 2.0 ATA, the average humidity was higher in the hyperbaric chamber than in the gas monitoring system (p&lt;0.001). Also, the average temperature was lower in the hyperbaric chamber than in the gas monitoring system (p&lt;0.001). The mean age of the 1,006 CO poisoning patients who received HBOT was 44.93±19.78 years. According to the source of CO, 680 patients (67.6%) visited ER most commonly due to charcoal. The median maximal CO exposure time and time from rescue to ER were 4.0 hours and 3.09 hours, respectively. The median GCS score at the scene or ER was 15. According to the underlying comorbidities, psychiatric diseases (19.5%) were the most common, followed by hypertension (18.1%) and diabetes mellitus (11.5%). In the emergency room, some patients had appeared symptoms such as loss of consciousness (59.8%), shock (6.7%), or seizure (8.3%). The results of this study could be expected that HBOT can be effectively performed by monitoring the gas concentration change inside the hyperbaric chamber.

The ozonation reaction in a bubble column reactor (BCR) has been widely used in the removal of phenol from wastewater, but the phenol removal efficiency in this type of reactor is limited because of low ozone solubility and reactivity in the system. In the present study, the phenol degradation was enhanced using α-Al2O3 as a packing material and a ZnO nanocatalyst in the BCR. The reactor diameter and height were 8 cm and 180 cm, respectively. The gas distributor was designed to include 52 holes of 0.5-mm diameter. Also, the gas holdup, pressure drop, and bubble size were measured as a function of the superficial gas velocity (i.e., 0.5, 1, 1.5, 2, 2.5, and 3 cm/s). The evaluation of the hydrodynamic parameters provided a deep understanding of the ozonation process to select the optimal operating parameters in the reactor. It was found that the best superficial gas velocity was 2.5 cm/s. A complete (100%) phenol removal was achieved for phenol concentrations of 15, 20, and 25 ppm at reaction times of 80, 90, and 100 min, respectively, using α-Al2O3 packing material and a ZnO nanocatalyst in the BCR. Additionally, the results provided a clear reaction mechanism describing the ozonized BCR. Finally, the applied treatment method can be used efficiently to remove phenol from wastewater at a low cost, with little consumed energy, and a simple operation.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

The positive impact of nature on human health has been explored by researchers. Although studies have indicated that olfaction and odors have an impact on both memory and health, re-search on the odor perception in relation to perceived health is scarce. A recent study found that the naturenatural scent from stem cuttings and potted plants of a specific rose-scented geranium Pelargonium graveolens, ‘Dr. Westerlund,’Westerlund’ had positive effects on stress-related mental disorders. reduction. Essential oils from many Pelargonium species, in particular ‘Dr. Westerlund’, are known to have phytochemical properties and pharmacological activities. No study has, so far, explored and identified the chemical com-pounds and the sensory perception of these compounds in stem cuttings and the potted ´Dr. Westerlund´ plantplants. Such knowledge would be an important contribution forto an increased understanding of the effects of plants’ chemical odor properties on human well-being and link this to the expressed perceived scents. Resulting sensory profiles of P.This study aimed to identify the sensory profile and suggest responsible chemical compounds of Pelargonium graveolens ´Dr. Westerlund´ as a potted plant and as stem cuttings were reported, as well as´. The sensory and chemical analysis results revealed sensory profiles of Pelargonium graveolens ´Dr. Westerlund´s, and suggestions for the chemical compounds that are attributed to the sensory profiles. Further studies are recommended to investigate the odor experience of scented pelargonium species in relation to various levels ofcorrelation between volatile com-pounds and possible stress hormones. reduction in humans.

Elevated salinity is one of the major environmental limitation factors of plant growth and development and salinity stress compromises the production and survival of plantation and urban forests and agricultural crops in the arid, semi-arid, and intertidal zones. Ulmus pumila, a salt- indigenous tree species in Asia and is widely deployed in salt-affected areas in China, and U.pumila is promising for multi-varietal forestry in plantation and urban forests. The comprehensive mechanism of the intraspecific salt tolerance is still not clear yet. Here, we investigated the physiological responses of the salinity stress based on the antioxidant enzyme activities, osmotic adjustments, and gas exchange among salt-tolerant U. pumila genotypes for 100 days under five different NaCl levels (0%, 0.3%, 0.5%, 0.7%, and 0.9% w/v) with natural surroundings and rain shade at age-2. Salt stress decreased height (HR), ground diameter (DR), and dry weight (biomass) were significantly different among genotypes. HR and performance indices were positively correlated with photosynthesis rate (Pn), apparent mesophyll conductance (AMC), and chlorophyll (CHLL) with (r= 0.7 - 0.8 ***), but were negatively related to the free proline, sugar, and protein accumulation (r=-0.5 ~ -0.7***). We found that high accumulation of sugars and more activities of SOD enzyme in leaf tissue contribute to the osmotic adjustment and ROS scavenging system under salinity treatment; the sugar content and SOD activity play key roles in U. pumila’s tolerance to salt stress, and are promising indicators for U. pumila species ex vitro selections. The ex vitro selection results align with the previous in vitro studies [37] and is promising for the MVF development.

Solar photovoltaic (PV) technology is a cornerstone of the global effort to transition towards cleaner and more sustainable energy systems. This paper explores the pivotal role of PV technology in re-ducing greenhouse gas emissions and combatting the pressing issue of climate change. At the heart of its efficacy lies the efficiency of PV materials, which dictates the extent to which sunlight is transformed into electricity. Over the last decade, substantial advancements in PV efficiency have propelled the widespread adoption of solar PV technology on a global scale. The efficiency of PV materials is a critical factor, determining how effectively sunlight is transformed into electricity. Enhanced efficiency, achieved through a decade of progress, has driven the global expansion of solar PV. Multi-junction photovoltaic materials have now exceeded 40% efficiency in lab tests. China leads the world in solar PV installations, boasting over 253 GW of installed capacity by the end of 2021. Other prominent countries in this sector are the United States, Japan, Germany, and India. Supportive policies like feed-in tariffs, net metering, tax incentives, and cost reductions in PV modules have made solar PV increasingly competitive against fossil fuel-based power generation. Solar PV technology holds immense potential for creating a cleaner, reliable, scalable, and cost-effective electricity system. To expedite its deployment and foster a more sustainable energy future, continued investment in research and development, along with supportive policies and market mechanisms, is essential. This paper underscores the pivotal role of solar PV technology in the global energy transition and advocates for a concerted effort to unlock its full potential in achieving a more sustainable and resilient energy future.

The present study utilizes a metal inert gas welding (MIG) to make a dissimilar weld joint of different stainless steel grades AISI 304, 314, 316L, 420 and a standard structural steel S355MC to estimate the correlation of a microstructure and the mechanical properties. The microstructure of the base metals (BM), the heat affected zone (HAZ), the fusion zone (FZ) and the weld seam were analyzed using optical microscopy. Optical microscopy did not reveal any presence of weld defects such as porosity or cracks. The analysis of microstructure showed that both the austenitic and martensitic stainless steel weld structures contain some retained delta ferrite and coarse Me23C6 carbides in the HAZ, while the FZ exhibits delta ferrite and some retained austenite. The hardness profiles revealed difference between austenitic and martensitic steel welds that the later showed extremely high values in the HAZ (~500 HV/0.1) which causes fracture in this zone. The welds of all austenitic steel grades withstood tensile test, showing the average tensile strength of 472 MPa with fracture observed in the base metal zone. It made clear that the use of a filler rod 308LSI is suitable only for the austenitic stainless and structural steel dissimilar welds, and not appropriate for martensitic-structural steel welds. The achieved results revealed that the higher hardness of the martensitic phase in the HAZ of AISI 420 is closely related with the formation of untempered coarse martensitic structure and higher carbon content.

Essential oils are mixtures of compounds obtained from plants, including flowers, roots, bark, leaves, seeds,peel, fruits, wood, that have risen up in the last decades thanks to their beneficial properties as antibacterial, antifungal and anti-inflammatory agents. The aim of this study was to characterize and analyze 13 different commercial essential oils with two different techniques. The first is GC-MS, coupled with SPME, thanks to which 204 different VOCs have been identified. The results show that a total of 95 compounds was found only in one oil, while the others were found with different frequencies in many of them. The most represented class is that of terpenes, as widely reported in literature. The second technique is based on an array of chemical gas sensors. This system was used to investigate whether sensors are able to identify these products. It turned out that basil, cinnamon and carnation are the most identifiable oils with different number and typology of sensors, especially tin oxide and copper oxide nanowires, while cayeput and thyme are more mistakable samples. Thanks to this detailed study, it has been possible to reach and obtain novel insights for the future development of this type of research.

SPME analysis of the scent Ophrys orchids gave the following results: O. apifera: benzyl benzoate, -copaene, caryophyllene, and cyclosativene. O. crabronifera subsp. biscutella: pentadecene, pentadecane, heptadecane, nonadecane, and heinecosane. O. bertolonii subsp. bertolonii: pentadecane, heptadecane and nonadecane. O. passionis subsp. garganica: i-propyl palmitate, caryophyllene, pentadecane, and heptadecane. O. holosericea subsp. apulica: -copaene, pentadecane, caryophyllene, and heptadecane. O. lacaitae: -copaene, pentadecane, heptadecane, and caryophyllene. O. bombyliflora: cyclosativene, pentadecane, and ethyl dodecanoate. O. insectifera: 8-heptadecene, pentadecane, and heptadecane. O. lutea: heptadecane, 8-heptadecene, nonadecane, and docosane. O. tenthredinifera subsp. neglecta: -copaene, caryophyllene, and i-propyl palmitate.

The amount of heat transfer in gas turbine blades depends on cooling techniques and various flow phenomena. The effect of eddies, passing shock waves and free flow turbulence has been noticed by many researchers since the beginning. The focus of the upcoming work is on the numerical investigation of the effects of turbulence intensity and Reynolds number on the amount of heat transfer from the blade surface with internal cooling. The SST model has been used to solve this problem, which has been compared with the experimental work to ensure the correctness of the numerical simulation. In this regard, by changing the free flow turbulence intensity with values of 1, 5, 7, and 10% and at three Reynolds numbers of 150,000, 350,000, and 750,000, the changes in heat transfer coefficients have been investigated. The results show that with the increase of the turbulence intensity at different Reynolds numbers, due to the positive effect of the flow turbulence on the suppression of separation and promotion of the boundary layer transition, the blade surface heat transferincreases and this increase is more evident at higher Reynolds numbers.

Transforming Small-Scale LNG Business, Enhancing Efficiency and Resilience in an Evolving Supply Chain In various industries, innovative systems have proven their value due to their efficiency and adaptability. A prime example of this lies in the rapid growth of the liquefied natural gas (LNG) market. LNG, a fuel derived from natural gas, has gained significant traction in recent years. In light of this, we aim to explore optimal strategies for small-scale LNG businesses, with a focus on revolutionizing their supply chain to ensure adaptability and sustainability. Our objective is to enhance efficiency and sturdiness in this evolving sector. By devising innovative methods and implementing cutting-edge technologies, we aim to revolutionize the small-scale LNG market, paving the way for a more optimized and resilient supply chain. Through this transformation, we strive to create a sustainable and adaptable framework that will drive the growth and success of a small-scale LNG businesses.LNG' ability to be transported and stored more cost-effectively in its reduced volume compared to natural gas in its original state is a significant advantage. The distribution network for LNG starts at numerous supply terminals and extends to a diverse range of consumption centers, each with varying tank capacities. In the broader economic context, the establishment of efficient routes for LNG Truck tank plays a critical role.To tackle the challenge of selecting a pickup location and determining optimal destinations with specific unloading volumes for liquefied natural gas (LNG), this research presents an innovative solution utilizing state-of-the-art machine learning techniques. The proposed approach combines the power of reinforcement learning, recurrent neural networks, online learning, and graph theory. By leveraging these cutting-edge techniques, we aim to develop an intelligent system that can effectively determine the most efficient pickup location and sequence of destinations for LNG delivery. This system will take into account various factors such as transportation costs tank capacity, and demand fluctuations. Through the integration of reinforcement learning, the system will continuously learn and improve its decision-making process in real-time. The recurrent neural networks will allow for the analysis of historical aim to model and optimize the complex network of pickup and delivery routes, considering factors such as distance, capacity constraints, and operational efficiencies. With this innovative approach, we strive to revolutionize the selection and planning process for LNG pickup and delivery, ultimately enhancing efficiency and reducing cost within the LNG supply chain.Improving the distribution network offers several financial benefits, including cost reduction, faster delivery times, more affordable distribution, and enhanced efficiency in the utilization of tanker trucks for LNG transportation. By optimizing the distribution network, transit costs associated with LNG transportation can be significantly lowered. This can be achieved through intelligent route planning, taking into account factors such as distance, traffic conditions, and fuel consumption. Minimizing transit costs contributes to overall savings for businesses operating in the LNG market. Faster delivery times are another advantage of an enhanced distribution network. By designing efficient routes and eliminating unnecessary detours or delays, the time taken for LNG to reach its intended destinations can be reduced. This not only improves customer satisfaction but also allows for more frequent deliveries and better coordination of supply and demand. Cheaper distribution is a direct outcome of an optimized distribution network. By strategically planning pickup locations, destinations, and intermediate stops, the costs associated with transferring LNG between terminals and consumption centres can be minimized. This leads to savings in transportation expenses, ultimately benefiting both businesses and end-users. Efficient utilization of tanker trucks is crucial for maximizing profitability in the LNG industry. An improved distribution network enables better allocation of resources, ensuring that tanker trucks are utilized optimally. This includes reducing empty or underutilized trips, maximizing load capacities, and minimizing idle time. Such efficiency improvements translate to cost savings and increased revenue for businesses involved in LNG transportation. Overall, the financial gains from improving the distribution network are substantial. Lower transit costs, faster delivery times, cheaper distribution, and more efficient use of tanker trucks contribute to increased profitability, competitiveness, and sustainability in the LNG market.

The pre-chamber technologies can improve the ignition performance of IC engines by more than two orders in magnitude and thereby substantial economic benefits. Compared with the common pre-chamber, a plug-and-play passive scheme is suitable for quick retrofit, which is getting more attention from the automobile industry. Good scavenging is the precondition for improving turbulent jet ignition performance for a passive pre-chamber. Therefore, detailed evaluations of the scavenging process and turbulent jet ignition deserve investigations for new pre-chamber schemes. In this paper, the effects of design parameters on ignition processes of plug-and-play passive pre-chamber were numerically studied, allowing for the lateral angle, orifice diameter, and vertical angle design. Seven pre-chamber schemes were evaluated, and four optimal ones were selected for bench tests. The characteristics of the scavenging process, turbulent jet ignition, and main-chamber combustion were investigated and analyzed. The results show that allowing for the trade-off between ignition energy and scavenging efficiency, the volume ratio of the pre-chamber to clearance is recommended to be 0.2~0.7%, and the corresponding area-volume ratio is 0.003~0.006 mm-1. Compared with the original natural gas engine, the pre-chamber retrofit can save up to 13.2% fuel consumption, which presents a significant improvement in fuel economy.

Basaltic activity is the most common class of volcanism on Earth, characterized by magmas of sufficiently low viscosities such that bubbles can move independently of the melt. Following exsolution, spherical bubbles can then expand and/or coalesce to generate larger bubbles of spherical-cap or Taylor bubble (slug) morphologies. Puffing and strombolian explosive activity are driven by bursting of these larger bubbles at the surface. Here, we present the first combined model classification of spherical-cap and Taylor bubble driven puffing and strombolian activity modes on volcanoes. We furthermore incorporate the possibility that neighboring bubbles might coalesce, leading to elevated strombolian explosivity. The model categorizes behavior in terms of the temporal separation between the arrival of successive bubbles at the surface and bubble gas volume or length, with the output presented on visually intuitive two-dimensional plots. The categorized behavior is grouped into the following regimes: puffing from a) cap bubbles; and b) non-overpressurised Taylor bubbles; and c) Taylor bubble driven strombolian explosions; each of these regimes is further subdivided into scenarios whereby inter-bubble interaction does/doesn't occur. The model performance is corroborated using field data from Stromboli (Aeolian Islands, Italy), Etna (Sicily, Italy) and Yasur (Vanuatu), representing one of the very first studies, focused on combining high temporal resolution degassing data with fluid dynamics, as a means of deepening our understanding of the processes which drive basaltic volcanism.

In this study, GC–IMS was used to analyze the volatile component and flavor profiles of Crassostrea gigas individuals of different ploidy and gender. Principal component analysis was used to explore overall differences in flavor profiles and a total of 54 volatile compounds were identified. The total volatile flavor contents in edible parts of tetraploid oysters were significantly higher than in diploid and triploid oysters. The concentrations of ethyl (E)-2-butenoate and 1-penten-3-ol were significantly higher of triploid oysters than in diploid and tetraploid oysters. In addition, the volatile compounds propanoic acid, ethyl propanoate, 1-butanol, butanal, and 2-ethyl furan were significantly higher in females than in males. The volatile compounds p-methyl anisole, 3-octanone, 3-octanone, and (E)-2-heptenal were present in higher levels in male than in female oysters. Overall, different ploidy and gender of oysters were being presented with different sensory characteristics, providing new insights for understanding the flavor characteristics of oysters.

Fabric phase sorptive extraction, an innovative integration of solid phase extraction and solid phase microextraction principles, has been combined with gas chromatography-mass spectrometry for the rapid extraction and determination of nineteen organochlorine pesticides in various fruit juices and water samples. FPSE consolidates the advanced features of sol-gel derived extraction sorbents with the rich surface chemistry of cellulose fabric substrate, which could directly extract target analytes from complex sample matrices and substantially simplifies the sample preparation operation. Important FPSE parameters including sorbent chemistry, extraction time, stirring speed, type and volume of back-extraction solvent and back-extraction time have been optimized. Calibration curves were obtained in the concentration range 0.1-500 ng/mL. Under the optimum conditions, the limits of detection were obtained in the range 0.007-0.032 ng/mL with satisfactory precision (RSD<6%). The relative recoveries obtained by spiking organochlorine pesticides in water and selected juice samples were in the range of 91.56–99.83%. The sorbent sol-gel poly(ethylene glycol)-poly(propylene glycol)-poly(ethylene glycol) was applied for the extraction and preconcentration of organochlorine pesticides in aqueous and fruit juice samples prior to analysis with gas chromatography-mass spectrometry. The results demonstrated that the present method is simple, rapid, and precise for the determination of organochlorine pesticides in aqueous samples.

In this paper we compare using computational fluid dynamics the aerothermal performance of two candidate casing manifolds for supplying an impingement-actuated active tip clearance control system for an aero-engine high-pressure turbine. The two geometries are (a) single-entry: an annular manifold fed at one circumferential location; (b) multiple-entry: a casing manifold split into four annular sectors, each sector supplied separately from an annular ring main. Both the single-entry and multiple-entry systems analysed in this paper are idealised version of active clearance control systems in current production engines. Aerothermal performance is quantitatively assessed on the basis of the heat transfer coefficient distribution, driving temperature difference for heat transfer between the jet and casing wall, and total pressure loss within the high-pressure turbine active clearance control system. We predict that the mean heat transfer coefficient (defined with respect to the inlet temperature and local wall temperature) of the single-entry active clearance control system is 77% greater than the multiple-entry system; primarily because the coolant in the multiple-entry case picks up approximately 40 K of temperature from the ring main walls, and secondarily because the average jet Reynolds number of impingement holes in the single entry system is 1.2 times greater than in the multiple entry system. The multiple-entry system exhibits many local hot and cold spots, depending on the position of the transfer boxes, while the single-entry case has a more predictable aerothermal field across the system. The multiple-entry feed system uses an average of 20% of the total available pressure drop, while the feed system for the single-entry geometry uses only 2% of the total available pressure drop. From the aerothermal results of this computational study, and in consideration of holistic aero-engine design factors, we conclude that a single-entry system is closer to an optimal solution than a multiple-entry system.

Introducing children to sustainable and healthy school meals can promote a long-term dietary shift to lower climate impact and improve population health. The aim of the OPTIMAT study was to optimize meals for minimum deviation from the current food supply while reducing greenhouse gases and ensuring nutritional adequacy without increasing cost. Optimized menus were tested in four primary schools in Sweden and effects on daily food consumption and waste evaluated. Pupils received their usual menu plan for three weeks and then the isocaloric optimized menu plan for another three weeks. Nutritional recommendations for a school lunch and a maximum of 500 grams of CO2eq/meal were applied as constraints during linear programming. Pulses, Cereals, Meat and Eggs increased, while Fats and Oils, Dairy, Sauces and Seasonings decreased. The amount of ruminant meat was reduced in favor of other meat products. The new menu was 28% lower in greenhouse gas emissions and slightly less costly than the original. No significant changes in mean food consumption or plate waste were found in interrupted time series analysis between the two periods. This pragmatic approach for combining linear optimization with meal planning could accelerate sustainable development of the meal sector in Sweden and abroad.

The present study was carried out at the north-eastern part of Bangladesh to investigate organochlorine pesticide (OCP) residues and microbiological quality of dried barb (Puntius sophore). Samples were collected from both producers and retailers from December 2016 to April 2017. A control sample was also prepared with the same raw fish used by the producers in the laboratory to compare the result. Gas Chromatography with Electron Capture Detector (GC-ECD) was used to detect and quantify OCP residues. Around 22 % (6) samples out of 27 were found contaminated with OCP residues. Among these six adulterated samples, four were from retailers and two from producers. Only Aldrin was detected in four samples and rest two samples were detected with both Aldrin + Dieldrin and Aldrin + Endrin. Aldrin was found between 0.332 to 0.967 ppm, Dieldrin 0.762 ppm, and Endrin 0.828 ppm. All these values were much higher than the Maximum Residual Limit (MRL) 0.1 ppm. Aerobic Plate Count (APC) of producer samples were ranged between log5.3 ± 0.02 to log5.4 ± 0.03, log6.2 ± 0.02 to log6.4 ± 0.02 for retailer samples and log5.0 ± 0.03 to log5.2 ± 0.04 for control samples. While fungal count was ranged between log3.2 ± 0.04 to log3.5 ± 0.04, log3.4 ± 0.04 to log3.6 ± 0.03 and log2.2 ± 0.05 to log2.5 ± 0.03 for producer, retailer and control samples respectively. All the producer and retailer samples and one-third of the control samples were found contaminated with Escherichia coli. Whereas, Salmonella sp. was detected as 13.3% in producer samples, 20% in retailer samples except for the control. In case of Vibrio sp., maximum count was found for retailer samples (13.3%), whereas, producer and control samples showed no detection. The finding of the present study revealed the presence of pesticides and poor microbiological quality of dried barb are alarming for the consumers of Bangladesh and which may cause chronic disease and potential long-term risk for human health.

The aim of this article is to review hydrogen combustion applications within the energy transition framework. Hydrogen blends are also included, from the well known hydrogen enriched natural gas (HENG) to the hydrogen and ammonia blends whose chemical kinetics is still not clearly defined. Hydrogen and hydrogen blends combustion characteristics will be firstly summarized, in terms of standard properties like the laminar flame speed and the adiabatic flame temperature, but also evidencing the critical role of hydrogen preferential diffusion in burning rate enhancement and the drastic reduction in radiative emission with respect to natural gas flames. Then, combustion applications in both thermo-electric power generation (based on internal combustion engines, i.e., gas turbines and piston engines) and hard-to-abate industry (requiring high temperature kilns and furnaces) sectors will be considered, highlighting the main issues due to hydrogen addition related to safety, pollutant emissions, and potentially negative effects on industrial products (e.g., glass, cement and ceramic).

In reservoir engineering, one of the main sources of information for the characterization of reservoir and well parameters is well testing. Among the unconventional well testing methodologies, Harmonic Well Testing (HPT) is appealing from an economic standpoint because it could provide well performance and reservoir behavior monitoring without having to interrupt field production. Recorded pressure analysis is performed in the frequency domain by adopting a derivative approach similar to conventional well testing. To this end, pressure and rate data must be decomposed into harmonic components. Test interpretability can be significantly improved if pressure data are detrended prior to interpretation, filtering out non periodic events such as discontinuous production from neighboring wells and flow regime variations which did not respect the designed test periodicity. Therefore, detrending offers the possibility of overcoming the limitation of HPT applicability due to the difficulty of imposing a regularly pulsing rate for the whole test duration (typically lasting several days). This makes HPT attractive for well performance monitoring, especially in gas storage fields. In this paper, the application of different detrending methodologies to synthetic HPT pressure data generated in different reservoir and operational scenarios is presented and discussed. Moreover, a real case application is also presented.

Faced with difficulties stemming from the complex interactions between tight gas sand bodies and fractures when describing and identifying reservoirs, a composite reservoir model was established. By setting the supply boundary to characterize the superposition characteristics of sand bodies, a mathematical model of unstable seepage in fractured vertical wells in tight sandstone gas reservoirs was constructed considering the factors such as stress sensitivity, fracture density and fracture symmetry. The seepage law and pressure response characteristics of gas well in tight sandstone discontinuous reservoir with stress sensitivity, semi-permeable supply boundary and complex fracture topology were determined, and the reliability of the model was verified. The research results more accurately depict the pressure characteristic curve of the superposed sand body complex fracture vertical well, and provide a more comprehensive model for tight gas production dynamic analysis and well test data analysis, which can more accurately guide the dynamic inversion of reservoir and fracture parameters.

A gas-hydrate method of CO₂ gas storage is one of the modern technology for reducing it emissions into the atmosphere. The breakup of gas bubbles by a shock wave is an actual area of scientific and technological research. However, it is little known that such research began in the late 1950s in the USSR. The article presents the main discoveries related to the destruction of gas bubbles in a liquid under the influence of a shock wave, made more than 60 years ago. Looking back: study the past to understand the present.

The increase in carbon dioxide emissions has a significant impact on human society and the global environment. As the most abundant and cheap C1 resource, the conversion and utilization of carbon dioxide has received extensive attention from researchers. In many methods of carbon dioxide conversion and utilization, the reverse water gas conversion reaction is considered to be one of the most effective ways. In this paper, the research progress of reverse water gas conversion reaction in recent years is introduced.

Soluble noble metal salts are widely used for loading noble metals as nano-catalysts in many applications. In this paper, Pt-SnO2 composite nanoceramics were prepared from SnO2 nanoparticles and H2PtCl6 using two Pt-loading methods separately: For the solution reduction method, the H2PtCl6 solution was added to a suspension of SnO2 and zinc powder to form Pt on SnO2 nanoparticles; and for the impregnation method, Pt was formed from H2PtCl6 in the course of sintering. Although a series of samples prepared using both Pt loading methods showed a strong response to H2 at room temperature, the ones prepared using the solution reduction method exhibited much better room temperature hydrogen sensing characteristics. For two samples of 0.5 wt% Pt and sintered at 825°C, the response value for the sample prepared using the solution reduction method was 5300 to 1% H2-20% O2-N2, which was much larger than that of 150 for the sample prepared using the impregnation method. Samples prepared using the two Pt loading methods have similar microstructures as characterized by XRD, FESEM, EDS, TEM, and HRTEM. However, the residual chlorine content in those using the impregnation method was found to be higher than that using the solution reduction method through analysis. It is proposed that the striking difference in the room temperature hydrogen sensing characteristics among samples prepared using these two different Pt loading methods separately resulted from their different chlorine removal process. This study demonstrates the importance of a proper method in loading noble metals from their soluble salts as nano-catalysts in many applications.

Some of Iran's gas resources are known as sour gas because one of the major by-products of this gas is water. In fact, natural gas is combined with water vapor in underground reservoirs. In some areas, the amount of water vapor in natural gas is so high that it can be used as a source of drinking water. However, it should be noted that water vapor in natural gas may exacerbate corrosion in pipes and industrial equipment, and the combustion of more natural gas produces high temperatures that can lead to the production of nitrogen oxides (NOx), which They are the cause of air pollution. This is while the processed gas has a standard percentage composition in which the amount of water has the lowest position. The removal of moisture from natural gas is due to the need to prevent the reduction of the calorific value of the gas and also to purify the gas in order to achieve the necessary standards for delivering gas to petrochemicals, industries and domestic uses. The main goal of this research is to investigate the influencing parameters on zeolite TiO2 nanocomposite membranes in order to absorb moisture from gas. For this reason, with the construction of a TiZ-V membrane as a standard membrane, the result of the initial evaluation of a suitable membrane for gas dehumidification was made, and this membrane was placed as a standard for measuring the effect of the manufacturing parameters in a way that in each stage of membrane construction It was found that it was different from standard TiZ-V membrane only in terms of one parameter. This type of investigation made it possible to determine the effect of various effective parameters in membrane construction on efficiency. The findings showed that increasing the concentration of SiO2 has the greatest effect on increasing the water flux of the membrane. According to the other findings of this study, the effect of increasing the reaction time of the vapor phase carrier has been to reduce the process of paternity selectivity loss at higher pressures. Although due to the safety limitation of the equipment to measure the efficiency of the membrane at pressures higher than 7 bar, this measurement was not carried out, but charts were presented regarding the state of the water in the water, which were a measure of the superiority of the water in the water in comparison to the gas in the water, which is the higher water in the water It is an indicator of the appropriateness of the membrane's efficiency at its corresponding pressure, so that the examination of the difference between these two graphs shows the possibility of using the membrane at higher pressures

This work presents an LC resonant passive wireless gas sensor with a novel structure designed to mitigate the negative impact of substrate. The LC sensor antenna with the new structure and the reader antenna were designed and optimized utilizing HFSS software to improve the transfer efficiency. The superiority of the designed structure compared with the general ones is highlighted and verified. The change in the substrate capacitance has essentially no interference with the parameters to be measured of the LC sensor. The sensor with the new structure was prepared by combining etching and sputtering methods. The structure of the ZnO nanowires (NWs) was characterized to confirm their high purity and wurtzite crystal structure. The LC gas sensors demonstrated excellent wireless sensing performance including a low detection limit of 0.5 ppm NO2, high response of 1.058 and outstanding stability at 180 °C. The developed new sensor structure not only prevented interference from the substrate during gas sensing testing, but also expanded the choice of sensor substrates, playing a critical role in the development of sensors based on LC resonance principle.

: We report on a direct correlation between macroscale structural variations and the gas sorption capacities of an ion gel. Here, we chose 1-ethyl-3-methylimidazolium bis(trifluoromethyl sulfonyl)imide ([Emim][TF2N]) and poly(vinylidene fluoride)-co-hexafluoropropylene (PVDF-HFP) as the ionic liquid and host polymer, respectively. The CO2 sorption in the thin films of IL-polymer was measured by the gravimetric method. The results of our experiment show that the trend of CO2 uptake of these mixtures is non-linearly correlated with the content of IL. Here we highlight the variation in the molecular structure of the polymers is the main reason behind the observed trend. The presented data suggest the possibility of using the composition of mixtures containing IL and polymers to realize a synergistic gain for gas sorption in these mixtures.

The previously developed models for fuel droplet heating and evaporation processes, mainly the Discrete Multi Component Model (DMCM), and Multi-Dimensional Quasi-Discrete Model (MDQDM) are investigated for the aerodynamic combustion simulation. The models have been recently improved, and generalised for a broad range of bio-fossil fuel blends so that the application areas are broadened with increased accuracy. The main distinctive features of these models are that they consider the impacts of species thermal conductivities and diffusivities within the droplets to account for the temperature gradient, transient diffusion of species and recirculation. A formulation of fuel surrogates is made, using the recently introduced model, referred to as ‘’Complex Fuel Surrogate Model (CFSM)’’ and analysing their heating, evaporation, and combustion characteristics. The CFSM is aimed to reduce the full composition of fuel to a much smaller number of components based on their mass fractions, and to formulate fuel surrogates. Such approach has provided a proof of concept with the implementation of the developed model into a commercial CFD code ANSYS-Fluent. A case study is made for the CFD modelling of gas-turbine engine using kerosene fuel surrogate. The surrogate is proposed using the CFSM. The model is implemented into ANSYS-Fluent via a user-defined function to provide the first full simulation of the combustion process. Detailed chemical mechanism is also implemented into ANSYS Chemkin for the combustion study.

Docked ships are a source of contamination for the city while they keep their engine working. Plumes emissions from large boats can carry a number of pollutants to the nearby cities causing a detrimental effect on the life quality and health of local citizens and ecosystems. A computational fluid dynamics model of the harbour area of Tromsø has been built in order to model the deposition of CO2 gas emitted by docked vessels within the city. The ground level distribution of the emitted gas has been obtained and the influence of the wind speed and direction, vessel chimney height, ambient temperature and exhaust gas temperature has been studied. The deposition range is found to be the largest when the wind speed is low. At high wind speeds, the deposition of pollutants along the wind direction is enhanced and spots of high pollutant concentration can be created. The simulation model is intended for the detailed study of the contamination in cities near the coast or an industrial pollutant source of any type of gas pollutants and can easily be extended for the study of particulate matter.

Solid porous materials, like zeolites, have been widely used in a variety of fields such as size and shape-selective absorption/separation and catalysis because of their porosity. But there are few liquid materials exhibit permanent porosity. Porous liquids are a novel material that combine the properties of fluidity and permanent porosity. It has potential applications in many fields such as gas separation, storage and transport. Herein, we report a novel Type 1 porous liquid prepared based on Silicalite-1. The pore size of this porous liquid was determined by positron annihilation lifetime spectroscopy (PALS), and the CO2 capacities was determined by the intelligent gravimetric analyser (IGA). The unique properties of this porous liquid can promote its application in many fields such as gas storage and transport.

Innovations and improvements in hydraulic fracturing and horizontal well technologies have contributed to the success of the shale gas industry; however, the industry is also challenged by freshwater use and environmental health issues. Increasing water impact makes precise quantification of water consumption important. The objective in this study was to better understand water sustainability and availability of the projected shale gas from 2018 to 2030 in the Weiyuan play, China. The water footprint framework was used to quantify the potential water use and environmental impacts on different time scales. The results showed that the water use per well ranged from 11351.3 to 60664.73 m3, with a median of 36013.94 m3, totaling ~3.44 Mm3 for 97 wells. Yearly evaluation results showed that the gray water footprint was the main contributor and accounted for 83.82% to 96.76%, which was dependent on different scenarios of treatment percentages. The monthly environmental impact results indicated that the annual streamflow statistics were more likely to prevent water withdrawal. Water quality issues may be alleviated through recycling and retreatment measures that improve current waste water management strategies. Resource regulators should manage their water resources by matching water demand to water availability or replenishment.

In this work, a tailored extreme learning machine (ELM) algorithm to enhance the overall robustness of gas analyzer based on the tunable diode laser absorption spectroscopy (TDLAS) method is presented. The ELM model is tailored through activation function selection, input weight and bias searching, and cross validation method to address the analyzer robustness issues for industrial process analysis field application. The two particular issues are the inaccurate gas concentration measurement caused by the process gas background components variation, and the inaccurate spectra shift calculation caused by spectral interference. By using our algorithm, the concentration error is reduced by one order of magnitude over a much larger stream pressure and component range compared with that obtained by classical least square (CLS) fitting methods based on reference curves. Additionally, it is shown that with our algorithm, the wavelength shift accuracy is improved to less than 1 count over 1000 counts spectra length. In order to test the viability of our algorithm, a trace ethylene (C₂H₄) TDLAS analyzer with coexisting methane was implemented, and its experimental measurements support analyzing robustness enhancement effect.

According to the operation conditions of time unlimited passive containment heat removal system (TUPAC), a separate effect experiment facility was established to investigate the heat transfer performance of steam condensation in presence of non-condensable gas. The effect of wall subcooling temperature, total pressure and mass fraction of the air on heat transfer process was analyzed. The heat transfer model was also developed. The results showed that the heat transfer coefficient decreased with the rising of subcooling temperature, the decreasing of the total pressure and air mass fraction. It was revealed that Dehbi’s correlation predicted the heat transfer coefficient conservatively, especially in the low pressure and low temperature region. The novel correlation was fitted by the data obtained in the following range: 0.20~0.45 MPa in pressure, 20% ~ 80% in mass fraction, 15°C ~ 45°C in temperature. The discrepancy of the correlation and experiment data was with ±20%.

Current education in biology is devoid of mathematics in many countries, probably because many relevant biological processes are explained from a qualitative point of view rather than addressing the quantitative aspects of these phenomena. Here, we employ a case study from the yeast physiology to illustrate the importance of numeracy skills for a deeper understanding of relevant biological problems. Yeast anaerobic growth on sugars is a widespread process as it is the basis for beer, bread, and winemaking and it is much akin to lactic acid fermentation in muscle cells in response to an increased energy demand. To study the physiology of yeasts under controlled conditions and being able to compare the results quantitatively, one ought to perform measurements and calculations involving concentrations of oxygen, biomass, and organic compounds. To set-up an “anaerobic” culture of Saccharomyces cerevisiae in a defined medium, one needs to calculate how much oxygen must enter the cultivation system, to meet the requirements for ergosterol and oleic acid biosyntheses, both of which require oxygen. Using basic physicochemical principles and simple mathematical skills, students will be able to compute the oxygen requirement for yeast growth under such “anaerobic” conditions.

Transport biofuels derived from biogenic material are used for substituting fossil fuels, thereby abating greenhouse gas (GHG) emissions. Numerous competing conversion options exist to produce biofuels, with differing GHG emissions and costs. In this paper analysis and modelling of the long-term development of GHG abatement and relative GHG abatement cost competitiveness between crop-based biofuels in Germany is carried out. Presently dominant conventional biofuels and advanced liquid biofuels were found not to be competitive compared to the substantially higher yielding options available: sugar beet based ethanol for the short to medium term least-cost option and Substitute Natural Gas (SNG) for the medium to long term. The competitiveness of SNG was found to depend highly on the emissions development of the power mix. Silage maize based biomethane was found competitive on a land area basis, but not on an energetic basis. Due to land limitations as well as cost and GHG uncertainty, a stronger focus on the land use of crop-based biofuels should be laid in policy.

Yellow nanorod Mg-MOF-74 was obtained by solvothermal synthesis method. XRD、N2 adsorption-desorption isotherms、SEM and TGA results suggest that the particle size of Mg-MOF-74 reaches 400 nm after the introduction of sodium acetate in the precursor of Mg-MOF-74. Besides, the morphology of Mg-MOF-74 was changed from cauliflower to rod particles. At the same time, the BET specific surface area and pore volume of Mg-MOF-74 were also increased a lot. Then the CO2 dynamic adsorption capacity of Mg-MOF-74 was measured by self-made fix bed under 30 ℃、0.1 bar CO2 partial pressure. The results show that the CO2 adsorption capacity of Mg-MOF-74-N2 reaches 3.67 mmol/g and its CO2 adsorption capacity remains unchanged after 10 times CO2 adsorption-desorption cycles.

To estimate The potential inventory of natural gas hydrates in the Levant Basin we correlated the gas hydrate stability zone (GHSZ), modeled with locally estimated thermodynamic parameters, with seismic indicators of gas. Compilation of oceanographic measurements define the deep-water temperature and salinity to 13.8°C and 38.8‰ respectively, predicting the top GHSZ at a water depth of 1250±5 m. Assuming beneath the seafloor a hydrostatic pore-pressure, the water body salinity, and geothermal gradients ranging between 20 to 28.5°C/km, yields a useful first-order base-GHSZ approximation. Our model predicts that the entire northwestern half of the Levant Basin lies within the GHSZ, with a median thickness of ~150 m. High amplitude seismic reflectivity (HASR) imaged on an extensive 3D seismic dataset, consistently correlates with verified active seafloor gas seepage and is pervasively distributed across the deep-sea fan of the Nile within the Levant. Two main trends observed for the distribution of HASR are suggested to represent: (1) shallow gas and possibly hydrates, within buried channel-lobe systems 25 to 100 m beneath the seafloor; and (2) a regionally discontinuous bottom simulating reflection (BSR) broadly matching the modeled base GHSZ. We therefore estimate the potential methane hydrates reserve within the Levant Basin at ~4 Tcf.

Biogas contains more than 40% CO2 that can be removed to produce high quality CH4. Recently, CH4 production from CO2 methanation has been reported in several studies. In this study, CO2 methanation of biogas was performed over a 20 wt% Ni-Mg-Al catalyst, and the effects of CO2 conversion rate and CH4 selectivity were investigated as a function of CH4, O2, H2O, and N2 compositions of the biogas. At a gas hourly space velocity (GHSV) of 30,000/h, the CO2 conversion rate was ~79.3% with a CH4 selectivity of 95%. In addition, the effects of the reaction temperature (200–450 °C), GHSV (21,000–50,000/h), and H2/CO2 molar ratio (3–5) on the CO2 conversion rate and CH4 selectivity over the 20 wt% Ni-Mg-Al catalyst were evaluated. The characteristics of the catalyst were analyzed using Brunauer-Emmett-Teller (BET) surface area analysis, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). The catalyst was stable for approximately 200 h at a GHSV of 30,000/h and a reaction temperature of 350 °C. CO2 conversion and CH4 selectivity were maintained at 75% and 93%, respectively, and the catalyst was therefore concluded to exhibit stable activity.

Gas leakage can occur for various reasons, including a gas leak in the distribution line, damaged regulators, service connection failures, fluctuations in inlet gas pressure, and other factors leading to millions in losses to the state. The objective is to develop a general and intelligent model for tracking and monitoring LPG distribution based on the Internet of Things and Business Intelligence technology. Devices such as sensors and actuators reduce risks and prevent accidents. IoT can also access automatic control of machines and infrastructure, and sensors’ data helps make intelligent decisions. The quantitative approach is used in the systematic review methodology based on the PRISMA statement; the architecture design is based on analytical research that studies the feasibility of a measure through empirical evidence; and the architecture description uses a qualitative approach. The Y.4908 Standard evaluates an IoT network’s interoperability, usability, and security. A targeted group of thirty IT professionals was surveyed to assess the Business Intelligence model. Forty scientific papers were selected for analysis. A model with IoT components and a four-level business intelligence system was found. At the overall average level, 49% strongly agree, 38% agree, 12% neither agree nor disagree, and 1% disagree. In other words, the model has an overall average approval rating of 87%.