The mass of a direct-drive generator is often defined by the requirements for structural stiffness to meet the magnetic stiffness between the rotor and stator surfaces. This paper analyses this magnetic stiffness and estimates the structural stiffness of direct-drive generators for different modes of deflection. The magnetic stiffness modelling is based on an analytical model of the airgap closing forces. The final models are verified using Finite Element analysis and carried out for both permanent magnet and wound rotor generators. It shows that wound rotor machines have higher stiffness requirements than permanent magnet machines. The structural stiffness of the generator rotor and stator are evaluated for different modes by applying spatially-varying forces and finding the associated deflections. Structural stiffnesses for the rotor, stator and bearing are then combined. Finally, the magnetic and structural stiffnesses are combined and a stiffness margin can be found. For the airgap not to close, this combined stiffness must be greater than 0. This method is applied to a relatively stiff and a relatively compliant set of generator structures in a case study in order to find the optimum and more sustainable configuration.

Rare-earth tetraborides RB4 are of great interest due to the occurrence of geometric magnetic frustration and corresponding unusual magnetic properties. While the Gd3+ spins in GdB4 align along the ab plane, Er3+ spins in the isomorphic ErB4 are confined to the c–axis. The magnetization in the latter exhibits a plateau at the midpoint of the saturation magnetization. Therefore, solid solutions of (Gd, Er)B4 provide an excellent playground for exploring the intricate magnetic behavior in these compounds. Single crystals of Gd(1-x)Erx B4 (x = 0, 0.2, and 0.4) were grown in aluminum flux. X-ray diffraction scans revealed single phase materials, and a drop in the unit cell volume with increasing Er content, suggesting the partial substitution of Er at the Gd sites. Heat capacity measurements indicated a systematic decrease of the Néel temperature (TN) with increasing Er content. The effective magnetic moment determined from the magnetization measurement agreed with the calculated free-ion values for Gd3+ and Er3+, providing further evidence for the successful substitution of Er for Gd. The partial substitution resulted in an anomalous ferromagnetic phase below TN, exhibiting significant anisotropy, predominantly along the c-axis. This intriguing behavior merits further studies of the magnetism in the Gd(1-x)ErxB4 borides.

The 11 system in iron-based superconducting family has become one of the most extensively studied materials in the research of high-temperature superconductivity due to their simple structure and rich physical properties. However, the research on 11 iron-based superconductors faces numerous obstacles, mainly stemming from the challenges associated with producing high-quality single crystals. Since the discovery of FeSe superconductivity in 2008, researchers have made significant progress in crystal growth, overcoming the hurdles that initially impeded their studies. Consequently, they have successfully established the complete phase diagrams of 11 iron-based superconductors, including FeSe1-xTex, FeSe1-xSx and FeTe1-xSx. In this paper, we aim to provide a comprehensive summary of the preparation methods employed for 11 iron-based single crystals over the past decade. Specifically, we will focus on hydrothermal, chemical vapor transport (CVT), self-flux, and annealing methods. Additionally, we will discuss the quality, size, and superconductivity properties exhibited by single crystals obtained through different preparation methods. By exploring these aspects, we can gain a better understanding of the advantages and limitations associated with each technique.

This brief commentary challenges the use of the term "energy deficiency" in nutrition and metabolism, providing a critical examination of its scientific and philosophical aspects. It emphasizes the need to consider rare diseases associated with actual energy deficiency, which extend beyond the scope of everyday tiredness or fatigue. By analyzing energy balance and its complexities, this critique underscores the oversimplification associated with the term and its potential for misleading implications. It highlights the dynamic nature of energy metabolism and the intricate mechanisms involved in maintaining energy equilibrium, including the impact of rare genetic and physiological abnormalities. In addition to the discussion on energy balance, this commentary explores the manifestation of rare diseases that disrupt energy production, utilization, or hormonal regulation. Conditions such as mitochondrial diseases, glycogen storage diseases, adrenal insufficiency, and Prader-Willi syndrome are examined, shedding light on their profound impact on individuals' energy levels and overall health. The distinct time courses, underlying mechanisms, and clinical implications of protein deficiency, energy deficiency, and vitamin C deficiency are also compared, further emphasizing the complexity of energy metabolism and its relationship with various nutrient deficiencies. To foster a more comprehensive understanding of energy metabolism and enhance clarity in communication within the field, the commentary proposes the adoption of alternative terminology, such as "energy flux," to capture the multifaceted nature of energy balance more accurately. By reevaluating the terminology employed, researchers and healthcare professionals can better convey the intricate dynamics of energy metabolism and address the unique challenges faced by individuals with rare diseases causing actual energy deficiency. In conclusion, this commentary serves as a thought-provoking exploration of the concept of energy deficiency in nutrition and metabolism. It highlights the limitations of the term in capturing the complexities of energy balance, particularly in the context of rare diseases. By broadening the discussion to include these rare conditions, it encourages a more comprehensive understanding of energy metabolism and calls for precise and nuanced terminology to facilitate effective communication and advancements in the field.

Space instable target simulator (SITS) is a vital actuator for ground verification of on-orbital capture technology, the motion performance of which directly affects simulation credibility. Different delays reduce the stability of SITS and ultimately lead to its divergence. In order to achieve high fidelity simulation, the impact of force measurement delay, discrete control cycle, and simulator response delay on stability is analyzed firstly. Then, the dynamic equation and transfer function identification model of hybrid simulator is constructed, and the necessary and sufficient conditions of its stability and convergence are obtained using the Routh criterion. After that, a switching compensator with variable gain is proposed, the compensation principle diagram of which is build, and its mathematical model including the energy observer and tracking differentiator is also established. Finally, three sets of numerical simulations are conducted to validate the correctness of the stability analysis and effectiveness of proposed compensation method. Simulation results show that all three types of delay can cause SITS to lose stability under critical stable motion state, and the delay in force measurement has the greatest impact, followed by the influence of control cycle. Compared with the force applied to simulated target, velocity and its recovery coefficient of space instable target using fixed gain and linear gain compensation, the proposed compensator has significantly better performance.

Nasal cavity is a primary checkpoint for the invasion of several respiratory pathogens. Numerous pathogens including SARS-CoV-2, S. pneumonia, S. aureus, etc., adhere to the nasal epithelium or mucus to invade and trigger an infection. IgA serves as the first line of defense against foreign antigens and pathogens. They exhibit cross-reactivity against a diverse variety of antigens through immune exclusion, which intercepts the invasion of pathogens through the mucosal lining. Advances in intranasal immunization technology underscore the elevated neutralizing IgA levels at local and distal mucosa in contrast to the parenteral vaccines. This review highlights the adjuvants that induce IgA class switching and the challenges of maintaining nominal IgA levels at the mucosal surface. Finally, the review features the paradigm-shifting of conventional immunization techniques to IgA-inducing vaccines to enhance protection against homologous and heterologous pathogens.

In the paper, a coordinated control methodology of single-phase (1-P) end-users switching oper-ations on the phases of an active electric distribution network (AEDN) has been proposed to ob-tain a minimum unbalance degree at the coupling common point (CCP) level with the main dis-tribution system. The phase load balancing (PLB) process considers the smart devices that switch from one phase to another phase the 1-P end-users (consumers and prosumers) to compensate for the phase load unbalance. The proposed methodology has been tested successfully in an AEDN belonging to a Romanian Distribution Network Operator (DNO) containing 114 end-users (104 consumers/10 prosumers) integrated into the Smart Metering System (SMS). The op-timal solution leads to a value of the objective function by 1.00004, represented by the unbalance factor, very close to the ideal target, 1.00. A comparative analysis was conducted considering other possible PLB cases (the consumer-level PLB and prosumer-level PLB), obtaining similar values of the UF (1.027 vs. 1.028), slightly higher than in the hybrid-level PLB. Also, the signifi-cant technical benefits were quantified through an energy-saving of 58.73% and decreasing the phase voltage unbalance rate by 91 % compared to the initial case (without PLB). These results emphasized the positive impact of the proposed coordinated control methodology on the PLB process and evidenced its effectiveness and applicability in the AEDNs.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

In this study, the hybrid biological ion exchange (BIEX) resin and gravity-driven membrane (GDM) process was employed for the treatment of coloured and turbid river water. The primary objective was to investigate the impact of both physical and chemical cleaning methods on ceramic and polymeric membranes in terms of stabilised flux, flux recovery after physical/chemical cleaning, and permeate quality. To address these objectives, two types of MF and UF membranes were utilised (M1 = polymeric MF, M2 = polymeric UF, M3 = ceramic UF, and M4 = lab-made ceramic MF).Throughout extended operation, the resin functioned initially in the primary ion exchange (IEX) region (NOM displacement with pre-charged chloride) and progressed to a secondary IEX stage (NOM displacement with bicarbonate and sulphate), while membrane flux remained stable. Subsequently, physical cleaning involved air/water backwash with two different flows and pressures, and chemical cleaning utilised NaOH at concentrations of 20 and 40 mM, as well as NaOCl at concentrations of 250 and 500 mg Cl2/L. These processes were carried out to assess flux recovery and identify fouling reversibility. The results indicated an endpoint of 1,728 bed volumes (BV) for the primary IEX region, while the secondary IEX continued up to 6,528 BV. At the end of the operation, DOC and UVA254 removal in the effluent of the BIEX columns were 68% and 81%, respectively, compared to influent water. This was followed by 30% and 57% DOC and UVA254 removal by M4 (ceramic MF). The stabilised flux remained approximately 3.8 – 5.2 LMH both before and after the cleaning process, suggesting that membrane materials do not play a pivotal role. The mean stabilised flux of polymeric membranes increased after cleaning, whereas that of ceramics decreased. Enhanced air–water backwash flow and pressure resulted in increased removal of hydraulic reversible fouling, which was identified as the dominant fouling type. Ceramic membranes exhibited higher removal of reversible hydraulic fouling than polymeric membranes. Chemical cleaning had a low impact on flux recovery; therefore, we recommend solely employing physical cleaning.

: Two-dimensional instability of a horizontal layer of boiling liquid with a finite height is experimentally studied. In this layer, “vapor columns” rose at the corners of a square rectangular grid. The symmetry of “vapor column” location on the heating surface is considered. The model considers the approach to the boiling crisis in terms of both developed nucleate boiling and transitional boiling (the Zuber problem). When dealing with developed nucleate boiling, the layer of boiling liquid is considered in calculations as an isotropic homogeneous system (foam). It is shown how the conditions on the heating surface (capillary-porous coating) affect external hydrodynamics of the liquid layer and, ultimately, the value of the critical heat flux. The calculation ratio obtained by approaching the boiling crisis with regard to developed nucleate boiling takes into account the dependence of the critical heat flux on the void fraction of the boiling liquid layer. A new solution to the boiling crisis problem is proposed when approaching the crisis from the point of transitional boiling (the Zuber problem). This new solution eliminates some shortcomings of the classical problem (in particular, the void fraction of the layer corresponds to the experiments).

All living cells maintain a charge distribution across their cell membrane (membrane potential) by carefully controlled ion fluxes. These bioelectric signals regulate cell behavior (such as migration, proliferation, differentiation) as well as higher-level tissue and organ patterning. Thus, voltage gradients represent an important parameter for diagnostics as well as a promising target for therapeutic interventions in birth defects, injury, and cancer. However, despite much progress in cell and molecular biology, little is known about bioelectric states in human stem cells. Here, we present simple methods to simultaneously track ion dynamics, membrane voltage, cell morphology, and cell activity (pH and ROS), using fluorescent reporter dyes in living human neurons derived from induced neural stem cells (hiNSC). We developed and tested functional protocols for manipulating ion fluxes, membrane potential, and cell activity, and tracking neural responses to wounding and re-innervation in vitro. Finally, using morphology sensor, we tested and quantified the ability of physiological actuators (neurotransmitters and pH) to manipulate nerve wound re-innervation. These methods are not specific to a particular cell type and should be broadly applicable to the study of bioelectrical controls across a wide range of combinations of models and endpoints.

Inverse problems of recovering surface fluxes on the boundary of a domain from pointwise observations are considered. Sharp conditions on the data ensuring existence and uniqueness of solutions in Sobolev classes are exposed. They are smoothness conditions on the data, geometric conditions on the location of measurement points, and the boundary of a domain. The proof relies on asymptotics of fundamental solutions to the corresponding elliptic problems and the Laplace transform. The problem is reduced to a linear algebraic system with a nondegerate matrix.

To clarify the relationships among critical temperature, critical magnetic field, and critical current density, this paper describes many-body interactions of quantum magnetic fluxes (i.e., vortices) and calculates pinning-related critical current density. All calculations are analytically derived, without numerical or fitting methods. Afteralculating a magnetic flux quantum mass, we theoretically obtain the critical temperature in a many-body interaction scenario (which can be handled by our established method). We also derive the critical magnetic field and inherent critical current density at each critical temperature. Finally, we determine the pinning-related critical current density with self-fields. The relationships between the critical magnetic field and critical temperature, inherent critical current density and critical temperature, and pinning critical current density and temperature were consistent with experimental observations. From the critical current density and critical magnetic field, we clarified the magnetic field transition. It appears that a magnetic flux quantum collapses when the lattice of magnetic flux quanta melts. Our results, combined with our previously published papers, provide a comprehensive understanding of the transition points in high-T_c cuprates.

Spinal and bulbar muscular atrophy (SBMA), also known as Kennedy’s disease, is a debilitating neuromuscular disease characterized by progressive muscular weakness and neuronal degeneration, affecting 1-2 individuals per 100,000 globally. While SBMA is relatively rare, recent studies have shown a significantly higher prevalence of the disease within the indigenous population of Western Canada compared to the general population. The disease is caused by a pathogenic expansion of polyglutamine residues in the androgen receptor protein, which acts as a key transcriptional regulator for numerous genes. SBMA has no cure, and current treatments are primarily supportive and focused on symptom management. Recently, a form of precision medicine known as antisense therapy has gained traction as a promising therapeutic option for numerous neuromuscular diseases. Antisense therapy uses small synthetic oligonucleotides to confer therapeutic benefit by acting on pathogenic mRNA molecules, serving to either degrade pathogenic mRNA transcripts or helping to modulate splicing. Recent studies have explored the suitability of antisense therapy for the treatment of SBMA, primarily focused on antisense-mediated mRNA knockdown approaches. Advancements in understanding the pathogenesis of SBMA and the development of targeted therapies offer hope for improved quality of life for individuals affected by this debilitating condition. Continued research is essential to optimize these genetic approaches, ensuring their safety and efficacy.

As a critical transmitter, the compact 532 nm lasers operating on high repetition and narrow pulse widths have been used widely for airborne or space-borne laser active remote sensing. We developed a free space pumped TEM₀₀ mode sub-nanosecond 532 nm laser that occupied a volume of less than 125 mm × 50 mm × 40 mm (0.25 liters). The fundamental 1064 nm laser consists of a passively Q-switched composite crystal microchip laser and an off-axis, two-pass power amplifier. The pump sources were two single-emitter semiconductor laser diodes (LD) of 808 nm with a maximum continuous wave (CW) power of 10 W each. The average power of fundamental 1064 nm laser was 1.26 W with the laser operating at 16 kHz repetition rates, and 857ps pulse widths. Since the beam distortion would be severe in microchip lasers in terms of the increase in heat load, for obtaining a high beam quality of 532 nm, the beam distortion was compensated by adjusting the distribution of pumping beam in our experiment of fundamental amplification. Furthermore, better than 0.6 W average power, 770 ps, beam quality of M² ＜1.2, and 16 kHz pulse output at 532 nm was obtained by a Type I LiB₃O₅ (LBO) crystal in the critical phase matching (CPM) regime for second harmonic generation (SHG).

Wall–stabilized arcs dominated by nozzle–ablation are key elements of self–blast circuit breakers. In the present study, high–current arcs were investigated using a model circuit breaker (MCB) in CO2 as gas alternative to SF6 and in addition a long polytetrafluoroethylene nozzle under ambient conditions for stronger ablation. The assets of different methods for optical investigation were demonstrated, e.g. high-speed imaging with channel filters and optical emission spectroscopy. Particularly the phase near current zero (CZ) crossing was studied in two steps. In the first step using high-speed cameras, radial temperature profiles have been determined until 0.4 ms before CZ in the nozzle. Broad temperature profiles with a maximum of 9400 K have been obtained from analysis of fluorine lines. In the second step, the spectroscopic sensitivity was increased using an intensified CCD camera, allowing single-shot measurements until few microseconds before CZ in the MCB. Ionic carbon and atomic oxygen emission were analyzed using absolute intensities and normal maximum. The arc was constricted and the maximum temperature decreased from >18000 K at 0.3 ms to about 11000 K at 0.010 ms before CZ. The arc plasma needs about 0.5-1.0 ms after both the ignition phase and the current zero crossing to be completely dominated by the ablated wall material.

This paper presents a control algorithm for soft-switching series LC converters. The conventional voltage-to-voltage controller is split into a master and a slave controller. The master controller implements constant-current-constant-voltage (CCCV) control, required for demanding applications, i.e. lithium battery charging or laboratory power supplies. It defines the set-current for the open-loop current slave controller, which generates the PWM parameters. The power supply achieves fast large-signal responses, e.g. from 5 V to 24 V, where 95% of the target value is reached in less than 400 µs. The design is evaluated extensively in simulation and on a prototype. A consensus between simulation and measurement is achieved.

COVID-19 is one of the deadliest respiratory diseases, and its emergence caught the pharmaceutical industry off guard. While vaccines have been rapidly developed, treatment options for infected people remain scarce, and COVID-19 poses a substantial global threat. This study presents a novel workflow to predict robust druggable targets against emerging RNA viruses using metabolic networks and information of the viral structure and its genome sequence. For this purpose, we implemented pymCADRE and PREDICATE to create tissue-specific metabolic models, construct viral biomass functions and predict host-based antiviral targets from more than one genome. We observed that pymCADRE reduces the computational time of flux variability analysis for internal optimizations. We applied these tools to create a new metabolic network of primary bronchial epithelial cells infected with SARS-CoV-2 and identified enzymatic reactions with inhibitory effects. The most promising reported targets were from the purine metabolism, while targeting the pyrimidine and carbohydrate metabolisms seemed to be promising approaches to enhance viral inhibition. Finally, we computationally tested the robustness of our targets in all known variants of concern, verifying our targets’ inhibitory effects. Since laboratory tests are time-consuming and involve complex readouts to track processes, our workflow focuses on metabolic fluxes within infected cells and is applicable for rapid hypothesis-driven identification of potentially exploitable antivirals concerning various viruses and host cell types.

This paper comprehensively reviews sensors and sensing devices developed or/and proposed so far utilizing two smart materials: electrorheological fluids (ERFs) and magnetorheological materials (MRMs) whose rheological characteristics such as stiffness and damping can be controlled by external stimuli, an electrical voltage for ERFs and a magnetic field for MRMs, respectively. In this review article, the MRMs are classified into magnetorheological fluid (MRF), magnetorheological elastomer (MRE) and magnetorheological plastomer (MRP). To easily understand the history of sensing research using the two smart materials, the order of this review article is organized in a chronological manner of ERF sensors, MRF sensors, MRE sensors and MRP sensors. Among many sensors fabricated from each smart material, one or two sensors or sensing devices are adopted to discuss on the sensing configuration, working principle and specifications such as accuracy and sensitivity. Some sensors adopted in this article include force sensor, tactile device, strain sensor, wearable bending sensor, magnetometer, display device and flux measurement sensor. After briefly describing what have been reviewed in a conclusion, several challenging future works, which should be done for practical applications as sensors or sensing devices, are remarked in terms of new technologies such as artificial intelligence neural network in which several parameters affecting the sensor signals can be precisely tuned or controlled. It is sure that this review article is very helpful to make creative sensors using not only the proposed smart materials but also several different types of smart materials including shape memory alloys and active polymers.

The effects of anisotropic properties (wettability and roughness) on microgroove surfaces in pool boiling heat transfer using Novec-7100 as a working fluid were experimentally investigated. The idea of introducing the concept of anisotropic wettability in boiling experiments draws inspiration from biphilic surfaces. The investigation is also motivated by two-phase immersion cooling, which involves phase-change heat transfer by using dielectric liquid as a working fluid. Very few studies have focused on the effects of surfaces with anisotropic properties on boiling performance. Thus, this study aims to examine the pool boiling heat transfer performance on surfaces with microgroove-induced anisotropic properties under the saturation condition. A femtosecond laser–texturing method was employed to create microgroove surfaces with different groove spacing. The results indicated that anisotropic properties affected the heat transfer coefficient and critical heat flux. Relative to the plain surface, microgroove surfaces enhanced the heat transfer performance due to the increased number of bubble nucleation sites and higher bubble detachment frequency. An analysis of bubble dynamics under different surface conditions was conducted with the assistance of high-speed images. The microgroove surface with groove spacing of 100 μm maximally increased the BHTC by 37% compared to the plain surface. Finally, the CHF results derived from experiments were compared with related empirical correlations. Good agreement was achieved between the results and the prediction correlation.

Experimental measurement of porous polypropylene (PP) using the DTC-25 TA laboratory equipment and hot box test has been compared. The thermal conductivity of materials indicates the insulation capability of building materials. Excellent building materials will have a lower thermal conductivities value as well as other building insulator performance metrics. While results show that increasing the volume fraction of fluid in the porous PP has an inverse association with the thermal conductivity of the material as predicted by porous media theories, there is a marked difference in the measured values of the thermal conductivity using the two methods. The thermal conductivity values of porous from DTC-25 and hot box test were 0.21 and 0.0033 W/mK, respectively. The difference in the thermal conductivity values was due to the misapplication of the Fourier’s guarded heat flow model in the DTC-25 device to a convective fluid porous medium material.

In this work, we demonstrate the preparation of easy-to-fabricate nanogranular, strontium ferromolybdate/strontium molybdate core-shell ceramics and examine their properties including tunnel magnetoresistance, magnetic field sensitivity and temperature coefficient of the tunnel magnetoresistance. The tunnel magnetoresistance of nanogranular, strontium ferromolybdate/strontium molybdate core-shell ceramics was modeled yielding values suitable for magnetoresistive sensor application. Such structures possess a narrow peak of magnetic flux sensibility located at about 125 mT. For magnetic flux measurement, single domain granules with superparamagnetic behavior should be applied. The predicted TMR magnetic flux sensitivities for granules with superparamagnetic behavior amount to about 7.7 % per T and 1.5 % per T for granules sizes of 6.8 nm and 4 nm, respectively. A drawback of the tunnel magnetoresistance of such nanogranular core-shell ceramics is the unacceptable large value of the temperature coefficient. Acceptable values, lower than 2 % per K, are obtained only at low temperatures (less than 100 K) or large magnetic flux densities (exceeding 6 T). Therefore, a Wheatstone bridge configuration should be adopted for magnetoresistive sensors design to compensate the effect of temperature.

The effect of high temperature (HT) stress on nicotine biosynthesis in Nicotiana attenuata was examined. Nicotine content was measured in mature leaves, young sink leaves and in roots from well-watered plants grown at 25 °C as controls and from plants exposed to 38 °C and 43 °C temperatures applied for 24, 48, 72 and 96-hr duration. At 38 °C, all leaf nicotine levels were significantly less than control plants for up to 72-hr exposure but rose sharply thereafter to levels significantly greater than controls with 96-hr exposure. In contrast, plants exposed to 43 °C never exhibited a reduction in leaf nicotine content and showed a significant increase in content with just 48-hr exposure. When radioactive 11CO2 was administered to plants, HT stress significantly reduced fixation. Furthermore, radiocarbon flux analysis revealed that ‘new’ C partitioning (as 11C) into the [11C]-amino acid pool was significantly reduced with HT stress as were yields of [11C]-aspartic acid, an important amino acid in nicotine biosynthesis, and its beta-amido counterpart [11C]-asparagine significantly reduced. In contrast, [12C]-aspartic acid levels appeared unaffected at 38 °C but were significantly elevated at 43 °C relative to controls. Additionally, [12C]-asparagine levels were significantly elevated at both stress temperatures. Finally, leaf total soluble protein (TSP) was reduced 39% with long exposures to both stress temperatures. However, Ribulose-1,5-bisphosphate carboxylase/oxygenase (Rubisco) which was 41% TSP appeared unaffected by HT stress. Altogether, these results support the theory that plant proteins other than Rubisco degrade at elevated temperatures freeing up essential amino acids supporting the nicotine biosynthetic machinery, and while feedback might downregulate de novo amino acid synthesis from ‘new’ C resources, more than likely plant C/N rebalancing caused by HT reductions in C input restricted N uptake, which in turn, limited this process.

The meshless Petrov-Galerkin (MLPG) method is developed to analyse 2-D problems for flexoelectricity and thermoelectricity. Both problems are multiphysical and scale dependent. The size-effect is considered by the strain- and electric field-gradients in the flexoelecricity and higher-grade heat flux in the thermoelectricity. The variational principle is applied to de-rive the governing equations considered constitutive equations. The order of derivatives in governing equations is higher than in equations obtained from classical theory. The coupled governing partial differential equations (PDE) are satisfied in a local weak-form on small fic-titious subdomains with a simple test function. Physical fields are approximated by the mov-ing least-squares (MLS) scheme. Applying the spatial approximations in local integral equa-tions a system of algebraic is obtained for the nodal unknowns.

A topological quantum interplay between the magnetic flux and the mass has been investigated, for the case of an electron, by evaluating a gauge-invariant phase factor (a Wilson loop) linked to the electromagnetic gauge field of the particle. In particular, from this phase factor and the quantization of the magnetic flux variations, a relationship between the mass at rest of the electron and its self-energy , arising from radiative corrections, has been obtained also within a QED approach. Besides, a formulation of an energy scale comparable to the energy at rest of an electron-positron pair is proposed. Remarkably, a reckoning of the Bohr energy of a W⁺ W^- pair is compatible with constants and parameters usually employed within the electroweak theory and comparable to the energy at rest of an electron-positron pair.

Channel bends are one of the most important characteristic features of natural streams. These bends often create the conditions for a hyporheic zone, which has been recognized as a critical component of stream ecosystems. The streambed vertical hydraulic conductivity (K_v), vertical hydraulic gradient (VHG) and Darcian flux (DF) in the hyporheic zone were estimated at 61 locations along a channel bend of the Beiluo River during July 2015 and January 2016. All the streambed attributes showed great spatial variability along the channel bend. Both upward fluxes and downward fluxes occurred during the two test periods, most of studied stream sections were controlled by downwelling, indicating stream water discharge into the subsurface. The average downward flux was higher at the downstream side than at the upstream side of the channel bend, especially in July 2015. The distribution of streambed sediment grain size has a significant influence on the variability of K_v; high percentages of silt and clay sediments generally lead to low K_v values. Higher K_v at the depositional left bank at the upstream site shifted toward the erosional right bank at the downstream site, with K_v values positively correlated with the water depth. This study suggested that the variabilities of K_v and VHG were influenced by the stream geomorphology and that the distribution of K_v was inversely related, to a certain extent, to the distribution of VHG across the channel bend. K_v and VHG were found to have opposite effects on the DF, and the close relationship between K_v and DF indicated that the water fluxes were mainly controlled by K_v.

Active front-end (AFE) rectifiers have been becoming widely employed in power systems to achieve unity power factor and harmonic mitigations. The typical modeling approaches applied for AFE rectifiers in the literature mostly relied on two baselines named the detailed model and the time average model. The former approach deals with the switching element model (SEM) leads to significant harmonics in currents with distorted waveforms. The latter approach uses the average-value model (AVM) to overcome the currents’ harmonics as well as provide fast responses. However, even the AVM baseline has contained problems during the starting stage (lack of control signals) and over the dead-time periods which causes serious issues in the implementation process. This paper presents an improved dynamic AVM for AFE rectifiers by precisely considering the issues mentioned above along with the practical starting procedure and desirable initialization. The studied AFE rectifier is developed using the voltage-oriented control (VOC) technique based on the different modeling methodologies including SEM, Conventional AVM, and the proposed AVM. The performance of all models is analyzed and compared using simulation results with MATLAB/Simulink R2023a Function blocks for all the algorithm parts and SimScape elements for the electrical circuit model. The simulation results illustrate that the performance of the proposed AVM approach can closely resemble the behavior of the SEM baseline with low harmonic distortion.

This paper investigates whether currency risk is priced differently in the different sectors (industrial, financial, and basic materials) of equity markets in a sample of developed United States of America (USA) and developing economies (Brazil, India, Poland, and South Africa). The paper makes use of the following techniques: (i) Univariate Autoregressive Fractionally Integrated Moving Average and Exponential General Autoregressive Conditional Heteroskedastic (ARFIMA-EGARCH), (ii) the Markov-Switching method (MS), and (iii) the Canonical Vine Copulas (C-Vine) techniques. Using a sample of daily data made of the foreign exchange rate against the domestic currency and equity market sectors; our findings show that there is an asymmetry effect between equities markets and the foreign exchange rate: there is a heterogeneous, strong, and positive dependence between the two. Higher equities prices are associated with depreciation of local currencies, according to US dollar (USD) exchange rates. In addition, we find that the selected emerging economies are pricing a positive and considerable currency risk. The pricing of currency risk has a varied effect in both regimes representing the states of the economy. In fact, when currency risk pricing has a beneficial impact on certain sectors of the economy, investors predict better returns.

This work presents a heat transfer and boiling model that computes the evolution of the temperature field in a representative steel workpiece quenched from 850 or 930°C by immersion in water flowing at average velocities of 0.2 or 0.6 m/s, respectively. Under these conditions, all three boiling regimes were present during cooling: stable vapor film, nucleate boiling, and single-phase convection. The model was based on the numerical solution of the heat conduction equation coupled to the solution of the energy and momentum equations for water. The mixture phase approach was adopted using the Lee model to compute the rates of water evaporation-condensation. Heat flux at the wall was calculated for all regimes using a single semi-mechanistic model. Therefore, evolution of boiling regimes at every position on the wall surface was automatically determined. Predictions were validated using laboratory results, namely: a) Videorecording the upward motion of the wetting front along the workpiece wall surface, and b) cooling curves obtained with embedded thermocouples in the steel probe. Wall heat flux calculations were used to determine the importance of the simultaneous presence of all three boiling regimes on the heat flux distribution. It was found that this simultaneous presence leads to high heat flux variations that should be avoided in production lines.

In this work,the wave behaviour propagation of single-walled fluid conveying carbon nanotubes (SWCNT) under longitudinal magnetic fields and elastic foundations is studied, based on the nonlocal strain gradients theory(NSGT). With considertion of surface effect, the governing differential equation are obtained utilising Timoshenko beam theory and Hamilton's variational principle. The influence of small-scale parameters, fluid density, magnetic flux, surrounding elastic medium and surface effects on wave behaviour characteristics of carbon nanotubes are discussed in detail. The numerical results illustrated that with the magnetic flux increase，the phase velocities of the carbon nanotube will increase. When the fluid effects inside the carbon nanotube, the wave frequencies of the system reduces with increase in the non-local coefficient, while promotes with increase in the strain gradient coefficient. In addition, fluid density, surrounding elastic medium and surface effects have meaningful influence on the phase velocity of the system.

Recently, the demand for electric vehicle is increasing worldwide due to eco-friendly policies and stricter emission regulations. As a traction motor for electric vehicle, interior permanent magnet synchronous motors are mainly used. For the design of the interior permanent magnet synchronous motor, the magnetic equivalent circuit method, which is a method of lumped constant circuit, and the finite element method, which is a method of distributed constant circuit, mainly are used. Magnetic equivalent circuit method is useful for simple design through fast and intuitive parameters, but it cannot derive the distribution of magnetic field. The finite element method can derive an accurate magnetic field distribution, but it takes a long time to analyze and it is difficult to analyze intuitive design parameters. In this paper, magnetic equivalent circuit method and Carter coefficient are mixed for rotor structure design. This design method will be called the hybrid magnetic equivalent circuit method. Intuitive design parameters are derived through this hybrid magnetic equivalent circuit method. We will derive the Air gap flux density distribution according to rotor shape, no-load induced voltage, and cogging torque, and compare and verify it with the finite element method.

Soil CO2 efflux (FCO2) plays a dominant role in the terrestrial carbon (C) cycle but interpreting constraints on local observations is impeded by challenges in disentangling belowground CO2 sources. Trees contribute most C to forest soils, so linking aboveground properties to FCO2 could open new avenues to study plant-soil feedbacks and facilitate scaling; furthermore, FCO2 responds dynamically to meteorological conditions, complicating predictions of total FCO2 and forest C balance. We tested for proximity effects of individual Acer saccharum Marsh. trees on FCO2, comparing FCO2 within 1 m of mature stems to background fluxes before and after an intense rainfall event. Wetting significantly increased background FCO2 (6.4±0.3 vs. 8.6±0.6 s.e. μmol CO2 m-2s-1), with a much larger enhancement near tree stems (6.3±0.3 vs. 10.8±0.4 μmol CO2 m-2s-1). FCO2 varied significantly among individual trees and post-rain values increased with tree diameter (with a slope of 0.058 μmol CO2 m-2s-1 cm-1). Post-wetting amplification of FCO2 (the ‘Birch effect’) in root zones often results from the improved mobility of labile carbohydrates and further metabolization of recalcitrant organic matter, which may both occur at higher densities near larger trees. Our results indicate that plant-soil feedbacks change through tree ontogeny and provide evidence for a novel link between whole-system carbon fluxes and forest structure.

Antimony (Sb) Substitution less than 10 % is examined on a single crystal of a layered superconductor NdO_0.7F_0.3BiS₂. Superconducting transition temperature of the substituted samples decreases with increasing Sb concentration. A lattice constant along the c axis showed a large decrease compared with that along the a axis. Since in-plane chemical pressure monotonically decreases with increasing Sb concentration, the suppression of the superconductivity is well described in terms of the decrease in in-plane chemical pressure.

Background: Metabolic flux analysis (MFA) is an indispensable tool in metabolic engineering. The simplest variant of MFA relies on an overdetermined stoichiometric model of the cell’s metabolism under the pseudo-steady state assumption, to evaluate the intracellular flux distribution. Despite its long history, the issue of model error in the overdetermined MFA, particularly misspecifications of the stoichiometric matrix, has not received much attention. Method: We evaluated the performance of statistical tests from linear least square regressions, namely Ramsey RESET test, F-test and Lagrange multiplier test, in detecting model misspecifications in the overdetermined MFA, particularly missing reactions. We further proposed an iterative procedure using the F-test to correct such an issue. Result: Using Chinese hamster ovary and random metabolic networks, we demonstrated that: (1) a statistically significant regression does not guarantee high accuracy of the flux estimates, (2) the removal of a reaction with a low flux magnitude can cause disproportionately large biases in the flux estimates, (3) the F-test could efficiently detect missing reactions, and (4) the proposed iterative procedure could robustly resolve the omission of reactions. Conclusion: Our work demonstrated that statistical analysis and tests could be used to systematically assess, detect and resolve model misspecifications in the overdetermined MFA.

The paper deals with one new property of the linear time-optimal control problems with real eigenvalues of the system, no matter of the number of eigenvalue multiplicity. This property unveils a prospective of synthesizing the time-optimal control without the need of describing the switching hyper-surfaces. The already chrestomathy example of the time-optimal control of a double integrator is resolved by the new technique and compared with the classical synthesis.

RNA polymerase III (RNAP III) holoenzyme activity and its products processing have been linked to several metabolic dysfunction in lower and in higher eukaryotes. Alterations in the activity of RNAP III driven synthesis of non-coding RNA, causes extensive changes in the glucose metabo-lism. Increased RNAP III activity in S.cerevisiae maf1Δ strain, manifests with lethality when grown on non-fermentable carbon source. This lethal phenotype is suppressed by reducing tRNA syn-thesis. The cause for the lack of growth neither the underlying molecular mechanism has not been deciphered and has been awaiting a scientific explanation for a decade. Our previous proteomics data suggested mitochondrial dysfunction of the strain. Using model mutant strains maf1Δ (with increased tRNA abundance) and rpc128-1007 (with reduced tRNA abundance) we collected data showing major changes in TCA cycle metabolism of the mutants that explain the phenotypic ob-servations. The present study, based on 13C flux data and analysis of TCA enzymes activities, identifies the flux constraints in the mitochondrial metabolic network. The lack of growth is associated with the de-crease in TCA cycle activity and downregulation of the flux towards glutamate, aspartate and phosphoenolopyruvate (PEP), the metabolic intermediate feeding gluconeogenic pathway. rpc128-1007, the strain that is unable to increase tRNA synthesis due to a mutation in C128 subunit, has increased activity of TCA cycle under non-fermentable conditions. To summarize, cells with non-optimal activity of RNAP III, undergo substantial adaptation to a new metabolic state, that make them vulnerable under specific growth conditions. Our results strongly suggest that balanced, non-coding RNA synthesis that is coupled to glucose signaling is a fundamental requirement to sustain cell’s intracellular homeostasis and flexibility under changing growth conditions. Presented results provide insight into the possible role of RNAP III in mito-chondrial metabolism of other cell types.

The application of diffusion dialysis using various types of ion-exchange membranes for the separation of sulfuric acid and nickel sulfate has been evaluated. The process of dialysis separation of a real waste solution from an electroplating facility containing 252.3 g/L of sulfuric acid, 20.9 g/L of nickel ions and small amounts of zinc, iron, copper ions, etc. has been studied. Heterogeneous cation-exchange membrane containing sulfo groups and heterogeneous anion-exchange membranes with different thicknesses (from 145 μm to 550 μm) and types of fixed groups (4 samples with quaternary amino groups and 1 sample with secondary and tertiary amino groups) are used. The diffusion fluxes of sulfuric acid, nickel sulfate, and the total and osmotic fluxes of the solvent are determined. The use of a cation-exchange membrane does not allow separation of the components, since the fluxes of both components are low and comparable in magnitude. The use of anion-exchange membranes makes it possible to efficiently separate sulfuric acid and nickel sulfate. At the same time, the thin dialysis membrane turns out to be the most effective, as well as the membranes with quaternary amino groups, and the membrane with secondary and tertiary amino groups proved to be the least effective.

This paper presents a new implementation of a 2-box absolute flow model, enabling the calculation of CO₂ transfer between the atmosphere and a mixing reservoir representing the combined effect of the terrestrial and ocean regions. The model uses published values of anthropogenic CO₂ fossil fuel emissions (CO2ff), atmospheric CO₂ mixing ratio and nuclear weapons bomb yields, to compute atmospheric d¹³C and Δ¹⁴C time-series. The level of agreement between the calculated values and the accepted values for d¹³C is within ± 0.05 ‰, and for Δ¹⁴C is within ± 3‰, spanning 200 years. The model contains only seven internal parameters; these are varied to optimize the fit, leading to reasonable parameter values, indicating the validity of the method. In addition, the model shows how a rising CO₂ exchange influx fluctuating with surface temperature is compatible with a nett atmospheric CO₂ sink. The study demonstrates that a single CO₂ residence time applies to both the ¹⁴C bomb pulse and the anthropogenic flux, contrary to the conventional view that "bomb radiocarbon and anthropogenic CO₂ do not behave identically." [Joos 1994 Nature 370, 181–182]. It is shown that the difference in behaviour, claimed to be due to seawater chemistry, is not significant in practice since fluctuating bulk carbon dominates fluctuating isotopic ratio. A new analysis of the airborne fraction indicates that the assumption of a time-dependent exchange influx results in a similar residence time for bulk CO₂ as for ¹⁴C in the nuclear bomb pulse, reinforcing the view that the ¹²C, ¹³C and ¹⁴C carbon isotopic forms of CO₂ behave similarly in the carbon cycle.

In this paper consider the circuitry of voltage followers (VF) with unity-gain, intended for practical use in active Sallen-Key RC-filters (LPF, HPF, BPF, RF). The results of research and computer modeling of radiation-resistant and low-temperature VF in the LTSpice environment on models of CJFET transistors operating under the influence of neutron flux up to 10e14 n/cm2 and cryogenic temperatures up to -197°C are presented.

This work aimed to assess and characterize the air quality in what concerns particulate pollution in urban-industrial environments. The main objectives were to study the spatial variability of the deposition flux of particulate pollution identifying areas with higher deposition, associate the variability with climatological variables and with possible surrounding emitting sources. The method for collecting the deposited particles was based on the standard NF X 43-007. Sampling for particulate pollution took place between April 2015 and February 2016, through seven sampling campaigns. Maps of the spatial dispersion for the particulate pollution were obtained through statistics and geostatistics techniques. Elemental identification by scanning electron microscopy (SEM) was also used but only in two sampling campaigns. The results show that the sampling campaigns that took place during hot and dry periods, 2nd and 3rd, present higher deposition flux: 2.04 g/(m2 x month) and 1.72 g/(m2 x month), respectively. Lower deposition fluxes were registered in the 6th and 7th campaigns: 0.23 g/(m2 x month) and 0.24 g/(m2 x month), respectively. It was also observed a recurrent high deposition at specific sampling points which may be due to both the nearby road traffic and the presence of chimneys. SEM analysis allowed to associate repetitive element deposition, at the same sampling point, to the same emitting source.

The separation of sister chromatids during anaphase is the culmination of mitosis and one of the most strikingly beautiful examples of cellular movement. It consists of two distinct processes: Anaphase A, the movement of chromosomes toward spindle poles via shortening of the connecting fibers, and anaphase B, separation of the two poles from one another via spindle elongation. I focus here on anaphase A chromosome-to-pole movement. The chapter begins by summarizing classical observations of chromosome movements, which support the current understanding of anaphase mechanisms. Live cell fluorescence microscopy studies showed that poleward chromosome movement is associated with disassembly, or ‘melting’ of the kinetochore-attached microtubule fibers that link chromosomes to poles. Microtubule-marking techniques established that kinetochore-fiber disassembly often occurs through a ‘pac-man’ mechanism, where tubulin subunits are lost from kinetochore-attached plus ends and the kinetochore appears to consume its microtubule track as it moves poleward. In addition, kinetochore-fiber disassembly in many cells occurs partly through ‘flux’, where the microtubules flow continuously toward the poles and tubulin subunits are lost from minus ends. Molecular mechanistic models for how load-bearing attachments are maintained to disassembling microtubule ends, and how the forces are generated to drive pac-man and flux-based movements, are discussed.

Transformer models have emerged as frontrunners in the field of natural language processing, primarily due to their adept use of self-attention mechanisms to grasp the semantic linkages between words in sequences. Despite their strengths, these models often face challenges in single-task learning scenarios, particularly when it comes to delivering top-notch performance and crafting strong latent feature representations. This challenge is more pronounced in the context of smaller datasets and is particularly acute for under-resourced languages such as Arabic. In light of these challenges, this study introduces a novel methodology for text classification of Arabic texts. This method harnesses the newly developed Reverse Positional Encoding (RPE) technique. It adopts inductive-transfer learning (ITL) framework combined with a switching self-attention shared encoder, thereby increasing the model's adaptability and improving its sentence representation accuracy. The integration of Mixture of Experts (MoE) and Reverse Positional Encoding (RPE) techniques empowers the model to process longer sequences more effectively. This enhancement is notably beneficial for Arabic text classification, adeptly supporting both the intricate five-point and the simpler ternary classification tasks. The empirical evidence points to its outstanding performance, achieving accuracy rates of 87.20% for the HARD dataset, 72.17% for the BRAD dataset, and 86.89% for the LABR dataset, as evidenced by the assessments conducted on these datasets.

Digital agricultural technology extension service and sustainable food production have attracted attention from academia. However, the association between digital agricultural technology extension service and sustainable food production has not yet been fully investigated. This research investigates the average and heterogeneous impacts of digital agricultural technology extension service use on eco-efficiency among 1302 maize producing farmers from Northeast China major maize producing area in 2022 to fill this knowledge gap. The slack-based measure model with undesirable outputs is applied to calculate the eco-efficiency of maize production. To obtain an unbiased estimation of the average effect, the self-selection problem generated by observable and unobservable factors is solved by the endogenous switching regression model. Quantile regression is utilized to analyze the heterogeneous effect. Notably, the mediated effects model is utilized to examine the potential mechanism between them. Our findings indicate that digital agricultural technology extension service use can increase maize production's eco-efficiency. Digital agricultural technology extension service users would reduce eco-efficiency by 0.148 (21.11%) if they had not used the digital agricultural technology extension service. Digital agricultural technology extension service nonusers would improve eco-efficiency by 0.214 (35.20%) if they had used it. The robustness check reconfirms the results. Moreover, digital agricultural technology extension service use is more helpful to maize farmers who have lower eco-efficiency than those who have higher eco-efficiency. Digital agricultural technology extension service use can improve eco-efficiency of maize production through the application of organic fertilizers, green pesticides and biodegradable agricultural films.

We have suggested earlier a new sustainable method for permafrost thermal stabilization that combines passive screening of solar radiation and precipitation with active solar-powered cooling of the near-surface soil layer thus preventing heat penetration in depth. Feasibility of this method has been shown by calculations, but needed experimental proof. In this article, we are presenting the results of soil temperature measurements obtained at the experimental implementation of this method outside of the permafrost area which actually meant higher thermal loads than in Polar Regions. We have shown that near-surface soil layer is kept frozen during the whole summer, even at air temperatures exceeding +30°C. Therefore, the method has been experimentally proven to be capable of sustaining soil frozen even in more extreme conditions than expected in permafrost areas. In addition to usual building and structure thermal stabilization, the method could be used to prevent the development of thermokarst, gas emission craters, and landslides; greenhouse gases, chemical, and biological pollution from the upper thawing layers at least in the area of human activities; protection against coastal erosion; and permafrost restoration after wildfires. Using commercially widely available components, the technology can be scaled up for virtually any size objects.

The circuitry of the summarized "floating" differential stages (FDS) based on complementary field-effect transistors with a control p-n junction (CJFET), intended for use in low-noise analog microcircuits, for example, operational amplifiers. The results of modeling the flow characteristics of one of the CJFET FDSs in the LTSpice XVII environment at low temperatures (down to -197 ⁰С) and exposure to a neutron flux in the range of 1e13 ÷ 1e15 n / cm² are presented.

The main objective of the paper is to provide a thorough analysis of currently used modulation control schemes for single phase bidirectional dual active bridge DC/DC converter. In this article, it will be shown that single phase shift, extended phase shift and Dual phase shift modulation schemes are special cases of triple phase shift (TPS) modulation scheme. The article aims to highlight six TPS switching modes and their complements with the operational constraints. Unlike previous studies that regarded TPS as a complex scheme, this paper simplifies the analysis of each mode and aims to standardize the understanding of TPS modulation in DAB converters. Power equations, range of power transferred and zero voltage switching (ZVS) are derived for all the modes under TPS without assuming fundamental component analysis. Additionally, a generic optimization algorithm is developed to show the advantages of TPS modulation and thus, detailed analysis presented in this paper provides valuable insights for single phase DAB converter designers in identifying a wide range of optimization algorithms to achieve higher efficiency under TPS modulation. This analysis contributes to the advancement of bidirectional DAB converter technology and facilitates its application in various power electronic systems.

Evapotranspiration (ET) is a major component of water budget in Bottomland Hardwood Forests (BHF) and is driven by a complex intertwined suite of meteorological variables. The understanding of these interdependencies leading to seasonal variations in ET is crucial in better informing water resource management in the region. We used a structural equation modeling approach to analyze the drivers of ET using Eddy covariance water and heat flux data collected from a BHF, located in the Russel Sage Wildlife Management Area (RSWMA). It consists of mature closed-canopy deciduous hardwood trees with an average canopy height of 27 m. Factor analysis was used to characterize the shared variance among drivers and path analysis was used to quantify independent contributions of individual drivers. In our results, ET and net radiation (Rn) showed similar variability patterns with Vapor Pressure Deficit (VPD) and temperature in Spring, Summer, and Autumn seasons while they differ in Winter season. The path analysis shows that Rn has the strongest influence on ET variations via direct and indirect pathways. In the deciduous forests like BHFs, our results suggest ET is more energy-dependent during growing season (Spring and Summer) and early non-growing season (Autumn) while more temperature-dependent during winter season.

The current view of the mitochondrial respiratory chain complexes I, III and IV foresees the oc-currence of their assembly in supercomplexes providing additional functional properties as compared with randomly colliding isolated complexes. According to the plasticity model, these two structural states of the respiratory chain may interconvert influenced by the intracellular prevailing conditions and in previous studies we candidated the mitochondrial membrane po-tential as a factor controlling their dynamic balance. Here, we extended those studies investigating if and how the cAMP/PKA-mediated signalling influences the aggregation state of the respiratory complexes. Analysis of inhibitory-titration profiles of the endogenous oxygen consumption rates in intact HepG2 cells with specific inhibitors of the respiratory complexes was performed to quantify, in the framework of the metabolic flux theory, the corresponding control coefficients. The results attained inhibiting pharmacologically either PKA and sAC indicate that the reversible phosphorylation of the respiratory chain complexes/supercomplexes influences their assembly state in response to the membrane potential. This conclusion is supported by scrutiny of the available structure of the CI,CIII2,CIV respirasome enabling to map several PKA-target serine residues exposed to the matrix side of the complexes I, III and IV at the contact interfaces of the three complexes.

The flux growth of InVO4 bulk single crystals has been explored for the first time. The reported eutectic composition at a ratio of V2O5:InVO4 = 1:1 could not be used as a self-flux, since no sign of melting was observed up to 1100 °C. Crystals of InVO4 of typical size 0.5×1×7 mm3 were obtained using copper pyrovanadate (Cu2V2O7) as a flux, using Pt crucibles. XRD confirmed the orthorhombic Cmcm structure. Rests of flux material were observed on the sample surface, with occasional traces of Pt indicating some level of reaction with the crucible. X-ray absorption spectroscopy showed that oxidation states of indium and vanadium ions are +3 and +5, respectively. The size and high quality of the obtained InVO4 crystals makes them excellent candidates for the further study of their physical properties.

The survey findings reveal that rivers worldwide carry an annual sediment load of 15 billion tons into the sea, and the Yellow River basin alone contributes 1.6 billion tons of sand. Therefore, understanding the science of wind and sand in the Yellow River is crucial to ensuring the safe development of similar basins across China and the world. This study examines the midstream wind and sand area of the Xiliugou tributary, a part of the upper Yellow River. The researchers used a stepped sand collector combined with an anemometer to measure the sand transport flux at 0-50 cm height on various underlying surfaces of the basin. Then, they estimated the amount of wind and sand entering the Yellow River using a function model based on the measured factors. Furthermore, the team analyzed the particle size composition of wind-eroded sand to better understand the principles of wind and sand erosion and accumulation in the basin. The results of the study show that the sand transport flux per unit area varies significantly across different underlying surfaces. Moreover, the contribution of moving sandy land, semi-fixed sand, and fixed sand to wind and sand deposition in the Yellow River basin was 77.08%, 15.30%, and 7.62%, respectively. The vertical change of sand transport rate on the basin's surface demonstrates that the total sand transport rate is an exponential function of wind speed. Based on this relationship, the researchers estimated that the total annual average wind and sand entering the Yellow River basin via the Xiliugou tributary is approximately 8.09×105t. Due to the basin's unique geography and sand source, the particle size composition of wind-eroded sand differs between the east and west sides of the river channel. On the west side, desert sand, mainly fine sand, and very fine sand constitutes the sand source. Conversely, on the east side, sand collected in the riverbed by secondary wind erosion is the primary sand source. Furthermore, human activities have disturbed the grain composition, mainly comprising powder and clay particles. This phenomenon, known as "wind-blown mud and water-washed sand," is evident in this geographical unit. In conclusion, the Yellow River basin still faces significant ecological security hazards. Understanding the coupling relationship between desert-basin-sand and wind is the foundation for effectively controlling wind and sand flow into the Yellow River basin.

Plasmonic nanocomposites have the ability to enhance light-matter interaction due to the plasmonic effects leading to promising potential applications. In this paper, we theoretically study the group index of the silver nanoparticle-gold nanoparticle-quantum dot plasmonic hybrid system in the optical region of the electromagnetic spectrum using the density matrix approach. The quantum dot is considered to be a three-level atomic system of a lambda configuration, interacting with strong control and weak probe fields. We find that the plasmonic hybrid system exhibits at near resonance a strong switching between slow and fast light, which can be controlled by the inclination angle of the gold nanoparticle and the size of the metals nanoparticles, in addition to the strength and detuning of the control field. Thus, the silver nanoparticle-gold nanoparticle-quantum dot could potentially be used in optoelectronic devices.

Humankind has entered a new era wherein a main characteristic is the convergence of various technologies providing services exerting major impact upon all aspects of human activity, be it social interactions as well as interactions with the natural environment. Fixed networks are about to play a major role in this convergence, since they form, along with mobile networks, the backbone that provides access to a broad gamut of services, accessible from any point of the globe. It is for this reason that we introduce a forward-looking approach for fixed networks, particularly focused on Fixed 6th Generation (F6G) networks. First, we adopt a novel classification scheme for the main F6G services, comprising six categories. This classification is based on the key service requirements, namely latency, capacity and connectivity. F6G networks differ from those of previous generations (F1G-F5G) in that they concurrently support multiple key requirements. We then propose concrete steps towards transforming the main elements of fixed networks, such as optical transceivers, optical switches etc. such that they satisfy the new F6G service requirements. Our study categorizes the main networking paradigm of optical switching into two categories namely ultra-fast and ultra-high capacity switching, tailored to different service categories. With regard to the transceiver physical layer, we propose: a) use of all-optical processing to mitigate performance barriers of analog to digital and digital to analog converters (ADC/DAC); b) exploitation of optical multi-band transmission, space division-multiplexing and adoption of more efficient modulation formats.

Antisense oligonucleotide (ASO)-mediated exon skipping has become a valuable tool for investigating gene function and developing gene therapy. Machine learning-based computational methods such as eSkip-Finder have been developed to predict the efficacy of ASOs via exon skipping. However, these methods are computationally demanding, and the accuracy of predictions remains suboptimal. In this study, we propose a new approach to reduce computational burden and improve prediction performance by using feature selection within machine learning algorithms and ensemble learning techniques. We evaluated our approach using a dataset of experimentally validated exon skipping events, dividing it into training and testing sets. Our results demonstrate that using a 3-way voting approach with random forest, gradient boosting, and XGBoost can significantly reduce computation time to under ten seconds while improving prediction performance, as measured by R2 for both 2’-O-methyl nucleotides (2OMe) and phosphorodiamidate morpholino oligomers (PMOs). Additionally, the feature importance ranking derived from our approach is in good agreement with previously published results. Our findings suggest that our approach has the potential to enhance the accuracy and efficiency of predicting ASO efficacy via exon skipping. It could also facilitate the development of novel therapeutic strategies. This study could contribute to the ongoing efforts to improve ASO design and optimize gene therapy approaches.

Antisense oligonucleotide (ASO)-mediated exon skipping has emerged as a powerful tool for examining the function of genes and exons in basic research, as well as gene therapy. Computational methods, such as eSkip-Finder, have been developed to predict the efficacy of ASOs via exon skipping using machine learning. However, these methods can be computationally demanding and the prediction accuracy of the tool is not yet optimal. In this study, we propose an approach to reduce computational burden and improve prediction performance by utilizing feature selection within machine learning algorithms and employing ensemble learning techniques. The method was evaluated using a dataset of genes with experimentally validated exon skipping events. The dataset was divided into training and testing sets to assess the accuracy of the algorithm. Our results demonstrate that using a 3-way voting approach with random forest, gradient boosting, and XGBoost can significantly reduce computation time to under ten seconds while improving prediction performance, as measured by R2 for both 2’-O-methyl nucleotides (2OMe) and phosphorodiamidate morpholino oligomers (PMOs). Additionally, the feature importance ranking derived from our approach is in good agreement with previously published results. These findings suggest that this approach has the potential to enhance the efficiency and accuracy of predicting ASO efficacy via exon skipping, facilitating the development of novel therapeutic strategies.

Molecule radiation can be used as a tool to study colder regions in switching arc plasmas like arc fringes in contact to walls and ranges around current zero (CZ). This is demonstrated in the present study for the first time for the case of ablation-dominated high–current arcs as key elements of self–blast circuit breakers. The arc in a model circuit breaker (MCB) in CO2 with and an arc in a long nozzle under ambient conditions with peak currents between 5 and 10 kA were studied by emission and absorption spectroscopy in the visible spectral range. The nozzle material was polytetrafluoroethylene (PTFE) in both cases. Imaging spectroscopy was carried out either with high-speed cameras or with intensified CCD cameras. A pulsed high-intensity Xe lamp was applied as background radiator for the broad-band absorption spectroscopy. Emission of Swan bands from carbon dimers was observed at the edge of nozzles only or across the whole nozzle radius with highest intensity in the arc center, depending on current and nozzle geometry. Furthermore, absorption of C2 Swan bands and CuF bands were found with the arc plasma serving as background radiator. After CZ, only CuF was detected in absorption experiments.

Electrical properties of the thin films of poly(arylene ether ketone) copolymers (co-PAEKs) with the fraction of phthalide-containing units of 3, 5 and 50 mol% in the main chain were investigated by using radiation induced conductivity (RIC) measurements. Transient current signals and current-voltage (I-V) characteristics were obtained under exposing 20÷25 thick films of the co-PAEKs to monoenergetic electron pulses of the energy ranged from 3 to 50 keV in the electric field ranged from 5 to 40 V/μm. The Rose-Fowler-Vaisberg semi-empirical model based on a multiple trapping formalism was used for an analysis of the RIC data and the parameters of the highly dispersive charge carrier transport were evaluated. The analysis revealed that charge carriers moved in isolation from each other and the applied electric fields were below the threshold field triggering the switching effect (a reversible high-to-low resistivity transition) in the co-PAEK films. It was also found that the co-PAEK films due to the super-linear I-V characteristics are highly resistant to electrostatic discharges arising from the effects of ionizing radiation. This property is important for the development of protective coatings for electronic devices.

In computer networks, loss of data packets is inevitable, in particular, because of the buffer memory overflow of at least one of the nodes located on the path from the source to the receiver, including the latter. Such losses associated with overflows are hereinafter referred to as congestion of network nodes. There are many ways to prevent and eliminate overloads; these methods, in the majority, are based on the management of data flows. A special place is taken by the maintenance of packages, taking into account their priorities. The article considers a number of original technical solutions to improve the quality of control and reduce the required amount of buffer memory of network nodes. The ideas of these solutions are quite simple for their implementation in the development of appropriate software and hardware for telecommunication devices.

Wetlands, which is composed of soil, vegetation and water, has sufficient water supply and is sensitive to climate change. This study analyzed the coupling degree between wetlands and atmosphere, and discussed the influence of environmental factors (solar radiation and water vapor pressure deficit) on latent heat flux by using the experimental data from the Maduo Observatory of Climate and Environment of the Northwest Institute of Eco-Environment and Resource, CAS and WRF model. The results showed, during the vegetation growthing season, the average value of Ω (decoupling factor) is 0.38 in alpine wetlands, indicating the coupling between wetlands and atmosphere is poor; Solar radiation is the main factor influencing the latent heat flux in the results of both observation data analysis and model simulation, and solar radiation and water vapor pressure deficit still have an opposite reaction to latent heat flux; when solar radiation and water vapor pressure deficit increase by 30%, the average daily amount of latent heat flux increases from 5.57 MJ·m-2 to 7.50 MJ·m-2 and decreases to 5.17 MJ·m-2, respectively. This study provides a new research approach for the study of the parameterization of latent heat flux and evapotranspiration under the context of global climate change.

This note makes available five years of data gathered in a measurement site equipped with a micrometeorological station and two monitoring wells. Series of data of hydrological and atmospheric variables allow to estimate the flux of water across the atmosphere-land interface and to calculate the water budget, that are crucial topics in climate and environmental sciences. The measures of water-table began during 2017, one of the driest year of the whole instrumental period of climate history for the Central Mediterranean. Data from the micrometeorological station have been used to construct two more datasets of daily and monthly cumulative values of different terms of the surface water budget, from which the groundwater infiltration has been estimated. A significant decreasing trend characterizes both the data time series of piezometric heights and estimated infiltration in the considered period. All the data are collected in 2017-2022 datasets that are available in the supplementary material.

Manipulating autophagy is a promising strategy for treating cancer as several autophagy inhibitors shown to induce autophagic cell death. One of these, autophagonizer (APZ), induces apoptosis-independent cell death by binding an unknown target via an unknown mechanism. To identify APZ targets we used a label-free drug affinity responsive target stability (DARTS) approach with a liquid chromatography/tandem mass spectrometry (LC-MS/MS) readout. Of 35 protein interactors, we identified Hsp70 as a key target protein of unmodified APZ in autophagy. Either APZ treatment or Hsp70 inhibition attenuates integrity of lysosomes, which leads to autophagic cell death exhibiting an excellent synergism with a clinical drug, temozolomide, in vitro, in vivo, and orthotropic glioma xenograft model. These findings demonstrate the potential of APZ to induce autophagic cell death and its development to combinational chemotherapeutic agent for glioma treatment. Collectively, our study demonstrated that APZ, a new autophagy inhibitor, can be used as a potent antitumor drug candidate to get over unassailable glioma and revealed a novel function of Hsp70 in lysosomal integrity regulation of autophagy.

A simple approach to enable water-management agencies employing free data to achieve the goal of using a single set of predictive equations for water-quality retrievals with satisfactory accuracy is proposed. Multiple regression-derived equations based on surface reflectance, band ratios, and environmental factors as predictor variables for concentrations of Total Suspended Solids (TSS), Total Nitrogen (TN), and Total Phosphorus (TP) were derived using a hybrid forward-selection method that considers Variance Inflation Factor (VIF) in the forward-selection process. Landsat TM, ETM+, and OLI/TIRS images were jointly utilized with environmental factors, such as wind speed and water surface temperature, to derive the single set of equations. The coefficients of determination of the best-fitting resultant equations varied from 0.62 to 0.79. Among all chosen predictor variables, ratio of reflectance of visible red (Band 3 for Landsat TM and ETM+, or Band 4 for Landsat OLI/TIRS) to visible blue (Band 1 for Landsat TM and ETM+, or Band 2 for Landsat OLI/TIRS) has a strong influence on the predictive power for TSS retrieval. Environmental factors including wind speed, remote sensing-derived water surface temperature, solar altitude, and time difference (in days) between the image acquisition and water sampling were found important in water-quality parameter estimation.

The nucleation and dynamics of Josephson and Abrikosov vortices determine the critical currents of layered high-T_c superconducting (HTS) thin films, grain boundaries, and coated conductors, so understanding their mechanisms is of crucial importance. Here we treat pair creation of Josephson and Abrikosov vortices in layered superconductors as a secondary Josephson effect, in which each full vortex is viewed as a composite fluid of micro-vortices, such as pancake vortices, which tunnel coherently via a tunneling matrix element. We introduce a two-terminal magnetic (Weber) blockade effect that blocks tunneling below a threshold current, and simulate time-correlated vortex tunneling above threshold. The model shows nearly precise agreement with voltage-current (V-I) characteristics of HTS cuprate grain boundary junctions, which becomes more concave rounded as temperature decreases, and also explains the piecewise linear V-I behavior observed in iron-pnictide bicrystal junctions and other HTS devices. When applied to either Abrikosov or Josephson pair creation, the model explains a plateau seen in plots of critical current vs. thickness of HTS coated conductors. The observed correlation between theory and experiment strongly supports the proposed quantum picture of vortex nucleation and dynamics in layered superconductors.

A review is here provided about the thermal effects on the optical chirality. To this goal, chiral objects dispersed in an embedding fluid are examined for their magnetoelectric coupling. Thermal effects on several chiral meta-atoms and their ensembles are examined. To this goal, DNA-like helical structures are examined in detail. Mechanical aspect of thermo-elasticity is reviewed along with transverse deformations, while drawing analogies from condensed-matter physics. In this respect, chirality-induced spin selection is reviewed along with the temperature-mediated elec-tron-phonon interactions. A wide range of materials such as polymers and biological cells are also examined for temperature effects. A transition temperature delineating a sign flip in the chirality parameter is identified as well. Chirality-associated functionalities such as ratchet motions, switching, and modulations are investigated for their respective thermal effects. Issues of fabri-cating chiral meta-atoms are also discussed.

A review is here provided on the thermal effects on the optical chirality. To this goal, chiral objects dispersed in an embedding fluid are examined for their magnetoelectric coupling. Archetypal twisted-Omega particles are examined with respect to electron transport, phonon dynamics, and temperature effects. Continuum-mechanical aspect of thermo-elasticity is reviewed along with transverse deformations. A transition temperature delineating a sign flip in the chirality parameter is identified as well.

Physical processes play important roles in controlling eutrophication and oligotrophication. In stratified lakes, internal waves can cause vertical transport of heat and nutrients without breaking the stratification, through boundary mixing events. Such is the case in tropical Valle de Bravo (VB) lake, where strong diurnal winds drive internal waves, boundary mixing and hypolimnetic warming during stratification periods. We monitored VB during 18 years (2001-2018) when important water-level fluctuations (WLF) occurred, affecting mixing and nutrient flux. Mean hypolimnetic temperature increase (0.06–1.04°C month-1) occurred in all the stratifications monitored. We analyzed temperature distributions and modeled the hypolimnion heat budget to assess vertical mixing between layers (26,618–140,526 m-3h-1), vertical diffusivity coefficient KZ (6.2x10-7–3.3x10-6 m2s-1) and vertical nutrient entrainment to epilimnion on monthly scale. Stability also varied as a function of WLF. Nutrient flux to the epilimnion ranged 0.36–5.99 mg m-2d-1 for soluble reactive phosphorus (SRP) and 5.8–97.1 mg m-2d-1 for dissolved inorganic nitrogen (DIN). During low water-level years, vertical nutrient fluxes increase and can account for up to >40% of the total external nutrients load to the lake. Vertical mixing changes related to WLF affect nutrient recycling, their flux to sediments, ecosystemic metabolic balance and planktonic composition of VB.

Electromagnetic actuation can support many fields of technology, such as robotics or biomedical applications. In this context, fully understanding the system behavior and proposing a low-cost package for feedback control is challenging. Modeling the electromagnetic force is particularly tricky because it is a nonlinear function of the actuated object’s position and coil’s current. Measuring in real time the position of the actuated object with the precision required for accurate motion control is also nontrivial. In this study, we propose a novel, cost-effective electromagnetic set-up to achieve position control via visual feedback. We actuate vertically and under different experimental conditions a 10 mm diameter steel ball hanging on a low-stiffness spring, demonstrating good tracking performance (the position error remains within ±0.5 mm with a negligible phase delay in the best scenarios). The experimental results confirm the feasibility of the proposed set-up, which is characterized by minimum complexity and realized with off-the-shelf and cost-effective components. For these reasons, such a contribution helps to understand and apply electromagnetic actuation even further.

Evaporating liquid sessile drop deposited on horizontal surface is an important object of applications (printing technologies, electronics, sensorics, medical diagnostics, hydrophobic coatings, etc.) and theoretical investigations (microfluidics, self-assembly of nanoparticle, crystallization of the solute, etc.). The arsenal of formulas for calculating the slow evaporation of an axisymmetric drop of capillary dimensions deposited on a flat solid surface is reviewed. Such characteristics as vapor density, evaporation flux density, total evaporation rate are considered. Exact solutions obtained in the framework of the Maxwellian model, in which the evaporation process of the drop is limited by vapor diffusion from the drop surface to the surrounding air, are presented. The summary covers both well-known results obtained during the last decades and new results published by us in the last few years, but practically unknown to the wide scientific community. The newest formulas, not yet published in refereed publications, concerning exact solutions for a number of specific contact angles are also presented. In addition, new approximate solutions are presented for the first time (total evaporation rate and mass loss per unit surface area per unit time in the whole range of contact angles ), which can be used in modeling without requiring significant computational resources.

This work deals with a numerical implementation of a fifth order CENTRAL WENO-TVD (\textit{Weighted Essentially Non-Oscillatory-Total Variation Dimimishing}) of Haschem (2006) scheme applied to the convective terms of some hyperbolic conservation laws problems, in a volume finite framework. The WENO-TVD scheme is used to solve the 1D advection and Burgers equations. For this case is implemented two different numerical fluxes: The Lax-Friedrichs and TVD fluxes. In the TVD fluxes the schemes applied are in flux-limiter form. The schemes implemented for this flux are: Van Albada-1 (van Albada et al.,1982), van Albada-2 (Kermani et al., 2003), van Leer (Hassanzadeh, 2009) and MINMOD (Hirsch, 2007). The WENO type schemes are characterized for their high order approximation, and do not produce spurious oscilations near discontinuities, shocks and higher gradients. A third order Runge-Kutta TVD for the temporal variable is used. Qualitative and quantitative comparison are presented. The numerical solutions are computed with an in-house computer code developed in MATLAB software. In future works, it will develope a paralelization of computer code for solving systems of conservation laws, e.g. Euler equations of gas dynamics.

One of the most destructive natural disasters is the earthquake which brings enormous risks to humankind. The objective of the current study was to determine the Earthquake’s remote sensing multiparameter (i.e. land surface temperature (LST), air temperature, specific humidity, precipitation and wind speed) spatiotemporal anomaly of many earthquake samples occurred during 2018 around the world. In this research 11 earthquake (M > 6:0) studied (4 samples selected in a land with transparent sky situations, 3 samples in land within cloudy situations and 4 samples in marine earthquakes). The interquartile range (IQR) and mean ± 2σ methods utilized to improve the efficiency of anomalous differences. As a result, based on the IQR method, negative anomaly before the event detected during the daytime in Mexico and during the nighttime in Afghanistan. In addition, a negative outlier of brightness temperature (BT) detected in Alaska before, after and during the event. In contrast, based on IQR and mean ± 2σ positive anomaly detected in precipitation before and after the event in all investigated examples. According to mean ± 2σ, negative anomaly LST, specific humidity, sea surface temperature (SST_100) and wind detected in most examined earthquake samples. In contrast, positive SST_0 anomaly observed in Fiji and Honduras after the earthquake. Our results suggested in marine earthquakes, for earthquake forecasting we can merge a prior negative anomaly in the wind speed and SST_100. Regarding the in land cloudy sky earthquakes, merging anomaly parameters could be the negative prior anomaly in BT, skin temperature, in contrast, a positive anomaly in precipitation. In land transparent sky earthquake, usually negative prior anomalies in air temperature, specific humidity and LST.

We investigate the shear quasinormal modes (QNMs) in the context of electron stars, focusing on the Lifshitz geometry and exploring the behavior in the small star limit. The study begins by analyzing the shear sector modes in the infrared (IR) Lifshitz limit, where the geometry approaches that of a pure Lifshitz space. We derive and solve the differential equations governing the shear modes, revealing the asymptotic behavior in terms of the Lifshitz exponent. In the special case of integer values of the exponent, we obtain analytic corrections to the solutions to extract hydrodynamical QNMs. We then explore the cases with a Lifshitz exponent equal to or greater than three, providing analytical corrections to the Lifshitz IR solutions. A special case with an exponent of two is also considered, leading to modified solutions. The study extends to finding hydrodynamical QNMs, emphasizing the role of the Lifshitz geometry. Further investigations involve the flux with real and complex frequencies, considering the off-shell Lagrangian and deriving conserved flux expressions. Our analysis focuses on the exterior of the star, modeled by the Reissner-Nordström-AdS geometry. The small star limit is examined, revealing interesting features in the behavior of fermionic excitations. In summary, we provide a detailed exploration of shear quasinormal modes in electron stars, shedding light on their behavior in Lifshitz geometry, small star limits, and the interplay between real and complex frequencies. Our findings contribute to our understanding of the dynamics of electron stars and their gravitational properties.

In our previous published papers, considering 3 large atomic gravitational constants assumed to be associated with weak, strong and electromagnetic interactions, we have proposed the existence of a nuclear charge of magnitude, e_n=2.95e and developed a nuclear mass formula associated with strong and weak interactions having 4 simple terms and only one energy coefficient. Two important assumptions are, there exists a weak fermion of rest energy 585 GeV and strong coupling constant is the squared ratio of electromagnetic charge and nuclear charge. The aim of this paper is associated with understanding the mystery of quantum of magnetic flux, Planck’s quantum radiation constant and Reduced Planck’s constant. Proceeding further, quark charges, strong coupling constant, nuclear stability, nuclear binding energy, medium and heavy atomic X-ray levels and celestial magnetic moments can be understood in a unified approach. It may also be noted that, by considering integral nature of elementary particle masses, it seems possible to understand the discreteness of angular momentum. Considering our proposed e_n=2.95e=3e as a characteristic nuclear charge, it seems possible to understand the integral nature of quarks electromagnetic charge. With this idea, neutron, proton and pions decay can be understood very easily. In all the cases, up quark of charge (±2e) seems to play a crucial role with the internal transformation of down quark of charge (±e) and external observable elementary basic elementary particles. It needs further study at fundamental level.

The current SARS-CoV-2 pandemic is still threatening humankind. Despite first successes in vaccine development and approval, no antiviral treatment is available for COVID-19 patients. The success is further tarnished by the emergence and spreading of mutation variants of SARS-CoV-2, for which some vaccines are not effective anymore. This highlights the urgent need for antiviral therapies even more. This article describes how the Genome-Scale Metabolic Model (GEM) of the host-virus interaction of human alveolar macrophages and SARS-CoV-2 was refined by incorporating the latest information about the virus’s structural proteins and the mutant variants B.1.1.7 and B.1.351. We confirmed the initially identified guanylate kinase as a potential antiviral target with this refined model and identified further potential targets from the purine and pyrimidine metabolism. The model was further extended by incorporating the virus’ lipid requirements. This opened new perspectives for potential antiviral targets in the altered lipid metabolism. Especially the phosphatidylcholine biosynthesis seems to play a pivotal role in viral replication. The guanylate kinase is even a robust target in all investigated mutation variants currently spreading worldwide. These new insights can guide laboratory experiments for the validation of identified potential antiviral targets. Only the combination of vaccines and antiviral therapies will effectively defeat this ongoing pandemic.