Most of the existing studies conducted on FRP-confined concrete considered circular and square concrete columns, while limited studies were on columns with rectangular sections. The studies have confirmed that the circular cross-sections exhibited higher confinement effectiveness, whereas in the case of non-circular cross-sections the efficiency of FRP confinement decreases with an increase of the sectional aspect ratio and there is no significant increase, particularly for columns with the aspect ratio of 2.0. As recently suggested by the researchers, to significantly increase the effectiveness of FRP-confinement for these columns is by modifying a rectangular section to an elliptical or oval section. According to the literature, most of the existing confinement models for FRP-confined concrete under axial compression have been proposed for columns with circular and rectangular cross-sections. However, modeling the axial strength and strain of concrete confined with FRP in elliptical cross-sections under compression is most limited. Therefore, this paper provides new expressions based on limited experimental data available in the literature. For a sufficient amount of FRP-confinement, the threshold value was proposed to be 0.02. Finally, the accuracy of the proposed model was verified by comparing its predictions with the same test database, together with those from the existing models.

The first detection of gypsum (CaSO4.2H2O) by the Mars Science Laboratory (MSL) rover Curiosity in the Gale Crater, Mars created a profound impact on planetary science and exploration. The unique capability of plasma spectroscopy involving in situ elemental analysis in extraterrestrial environments, suggesting the presence of water in the red planet based on phase characterization and providing a clue to Martian paleoclimate. The key to gypsum as an ideal paleoclimate proxy lies in its textural variants, and in this study terrestrial gypsum samples from varied locations and textural types have been analyzed by Laser Induced Breakdown Spectroscopy (LIBS) technique. Petrographic, sub-microscopic and powder X-ray diffraction characterizations confirm the presence of gypsum (hydrated calcium sulphate; CaSO4.2H2O), bassanite (semi-hydrated calcium sulphate; CaSO4.1/2H2O) and anhydrite (anhydrous calcium sulphate; CaSO4) along with accessory phases (quartz and jarosite). The principal component analysis of LIBS spectra from texturally varied gypsums can be differentiated from one another because of the chemical variability in their elemental concentrations. The concentration of gypsum is determined from the partial least-square regressions model. Rapid characterization of gypsum samples with LIBS is expected to work well in extraterrestrial environments.

Cancer stem cells (CSCs) have been identified in many cancer types. This study identified and characterized CSCs in head and neck metastatic malignant melanoma (HNmMM) to regional lymph nodes using induced pluripotent stem cell (iPSC) markers. Immunohistochemical (IHC) staining performed on 20 HNmMM tissue samples demonstrated expression of iPSC markers OCT4, SOX2, KLF4 and c-MYC in all samples while NANOG was expressed at low levels in two samples. Immunofluorescence (IF) staining demonstrated an OCT4+/SOX2+/KLF4+/c-MYC+ CSC subpopulation within the tumor nests (TNs) and another within the peritumoral stroma (PTS) of HNmMM tissues. IF also showed expression of NANOG by some OCT4+/SOX2+/KLF4+/c-MYC+ cells within the TNs in an HNmMM tissue sample that expressed NANOG on IHC staining. In situ hybridization (n=6) and reverse-transcription quantitative polymerase chain reaction (n=5) on the HNmMM samples confirmed expression of all five iPSC markers. Western blotting of four primary cell lines derived from four of the 20 HNmMM tissue samples showed expression of SOX2, KLF4, and c-MYC but not OCT4 and NANOG, and three of these cell lines formed tumorspheres in vitro. We demonstrate the presence of two putative CSC subpopulations within HNmMM, which may be a novel therapeutic target in the treatment of this aggressive cancer.

There are numerous hazards found on the farms. Most of them are ignored, which might cause the farmer to pay later in terms of his ill health, potential injuries or death. The current article discusses some of the common issues such as dust and air quality concerns; environmental (weather) stressors and psychological stressors; noise and hearing protection; and tractor safety and seatbelt use. And finally, the recommendations to overcome the hazards are discussed.

Maintenance of integrity and function of the gastric mucosa (GM) requires a high regeneration rate of epithelial cells during the whole life span. The health of the gastric epithelium highly depends on redox homeostasis, antioxidant defense and activity of detoxifying systems within the cells as well as robustness of blood supply. Bioactive products of lipid peroxidation, in particular second messengers of free radicals, the bellwether of which is 4-hydroxynonenal (HNE), are important mediators in physiological adaptive reactions and signaling but they are also thought to be implicated in the pathogenesis of numerous gastric diseases. Molecular mechanisms and consequences of increased production of HNE and its protein adducts in response to stressors during acute and chronic gastric injury are well studied. However, several important issues related to the role of HNE in gastric carcinogenesis, tumor growth and progression, the condition of GM after eradication of Helicobacter pylori, or the relevance of antioxidants for HNE-related redox homeostasis in GM still need more studies and new comprehensive approaches. In this regard, preclinical studies and clinical intervention trials are required, which should also include the use of state-of-the-art analytical techniques such as HNE determination by immunohistochemistry and ELISA as well as modern mass-spectroscopy methods.

Background: In hepatocytes and alcohol-metabolizing cultured cells, Golgi undergoes ethanol (EtOH)-induced disorganization. Periniclear and organized Golgi is important in liver homeostasis, but how the Golgi remains intact is unknown. Work from our laboratories showed that EtOH-altered cellular function could be reversed after alcohol removal; we wanted to determine whether this recovery would apply to Golgi. Methods: We used alcohol-metabolizing HepG2 (VA-13) cells (cultured with or without EtOH for 72 h) and rat hepatocytes (control and EtOH-fed (Lieber-DeCarli diet). For recovery, EtOH was removed and replenished with control medium (48 hours for VA-13 cells) or control diet (10 days for rats). Results: EtOH-induced Golgi disassembly was associated with de-dimerization of the largest Golgi matrix protein giantin, along with impaired transport of selected hepatic proteins. After recovery from EtOH, Golgi regained their compact structure, and alterations in giantin and protein transport were restored. In VA-13 cells, when we knocked down giantin, Rab6a GTPase or non-muscle Myosin IIB, minimal changes were observed in control conditions, but post-EtOH recovery was impaired. Conclusions: These data provide a link between Golgi organization and plasma membrane protein expression and identify several proteins whose expression is important to maintain Golgi structure during the recovery phase after EtOH administration.

Spatially resolved, line-of-sight measurements of aluminum monoxide emission spectra in laser ablation plasma are used with Abel inversion techniques to extract radial plasma temperatures. Contour mapping of the radially deconvolved signal intensity shows a ring of AlO formation near the plasma boundary with the ambient atmosphere. Simulations of the molecular spectra were coupled with the line profile fitting routines. Temperature results are presented with simultaneous inferences from lateral, asymmetric radial, and symmetric radial AlO spectral intensity profiles. This analysis indicates that we measured shockwave phenomena in the radial profiles, including a temperature drop behind the blast wave created during plasma initiation.

Type 1 diabetes affects millions of people globally and requires careful management to avoid serious long-term complications, including heart and kidney disease, stroke, and loss of sight. The present standard-of-care for type 1 diabetes is exogenic insulin substitutional therapy. The most advanced stretegies in this area is the development of hybrid-closed loop system and the producing of long-acting insulins. Progresses in stem cell therapies have started to revolutionize the care of patients with type 1 diabetes; however, significant challenges remain including the limited islets availability, difficulties in maintaining the viability, the heterogeneity within a complex pathology and in patients’ responses to treatment. On the way, a considerable amount of efforts in maximizing the islet transplantation effectiveness by controlling the advantageous of different stem cell approaches. With the availability and the use of big data, the concept of precision medicine is gaining wide attention worldwide and could bring the dream of “presonlaized” therapies as a reality in the near future. Here we review the current range of treatments available as well as recent pre-clinical breakthroughs in the field of personlaized medicine for type 1 diabetes.

This study numerically analyzed the effect of composition and temperature and oxygen concentration changes on the selfignition characteristics of n-heptane/methane blended fuels in order to cope with development of alternative fuels and international environmental regulations. CHEMKIN-PRO is used as the analysis program and the LLNL model is used as the reaction model. The numerical results revealed that on autoignition and ignition delay time were sensitive to changes in fuel composition and oxygen concentration. As the methane ratio increases, OH radicals causing ignition are delayed in generation and the concentration is lowered, thus longer the ignition timing. The oxygen concentration in the mixed fuels are changed to simulate the exhaust gas recirculation and a numerical analysis in then performed. As the oxygen concentration decreases, the ignition delay time longer because the nitrogen gas acts as a thermal load in the combustion chamber.

Introduction: Valproic acid (VPA) is an antiepileptic drug extensively used for treating partial and generalised seizures, acute mania and as prophylaxis for bipolar disorder. Drug-induced liver injury (DILI) persists as a significant issue related to fatal outcomes by VPA. The aim of this study was to increase our knowledge about this condition and to better identify patients affected. Methods: We conducted an observational retrospective case-control study that identified cases of DILI by VPA from the Pharmacovigilance Programme from our Laboratory Signals at La Paz University Hospital from January 2007 to December 2019. From the Therapeutic VPA Monitoring Programme, two control groups were assigned, VPA-tolerant patients and the other with patients who developed mild VPA-related hepatitis but who did not meet the DILI criteria, matched for date, age and sex. Results: A total of 60 patients were included in the study: 15 cases of DILI, 30 VPA-tolerant controls and 15 controls with mild hepatitis. Mean age for the cases was 45.7 years, 4(26.7%) were women and 5(33.34%) were children under 18 years, of them 3(20%) were fatal. Polytherapy with other antiepileptic drugs (p=0.047) and alcohol consumption (p<0.001) were associated with a greater risk of developing DILI by VPA. A diagnosis of epileptic seizure was more frequently related to DILI when compared with the VPA-tolerant controls (p<0.001). The cases developed hepatocellular hepatitis (p<0.001), while the mild hepatitis controls had a higher rate of cholestatic hepatitis (p<0.001). The laboratory lactate dehydrogenase values were statistically higher (even at baseline) in patients with DILI than in both control groups (p= 0.033 and p=0.039). Conclusions: VPA hepatotoxicity remains a considerable problem. This study offers interesting findings for characterising VPA-induced liver injury and at-risk patients.

The segmentation and de-noising are basic operations, required in every signal processing and classification system. The classical segmentation and de-noising approaches are time-invariant. Consequently, it results in the post processing of an unnecessary information and causes an increase in the system processing activity and power consumption. In this context, an efficient event-driven segmentation and de-noising technique is proposed. It is founded on the principles of level crossing and activity selection. Therefore, it can adapt its sampling frequency, segmentation window length and position along with the filter order by analyzing the input signal local characteristics. As a result, the computational complexity and the power consumption of the proposed system is reduced compared to the counter ones. The suggested system performance is compared with the classical one. It is done for the case of a multi-channel Electroencephalogram (EEG) signals. Results show a noticeable compression gain with an effective adaptation of the de-noising filters order. It aptitudes a significant computational gain, transmission data rate reduction and power consumption reduction of the proposed technique, compared to the counter ones. It shows that the proposed solution is an attractive candidate to embed in the new generation EEG wearables.

In intermediary metabolism, enzymes are mainly for the specific provision of one small molecule from another, B from A, for its further use. But there are also decades of work relating to another evolved purpose, which is to prevent untoward effects of odd compounds of various origins, and of ordinary intermediates, whose improper concentrations may be avoided by hydrolases and other activities of metabolic correction.

Appropriate estimation of soil settlement is of significant importance since it directly influences the performance of building and infrastructures that are built on soil. In particular, the settlement of fine-grained soils is critical because of low permeability and continuous settlement with time. Coefficient of consolidation (C_c) is a key parameter to estimate settlement of fine-grained soil layers. However, estimation of this parameter is time consuming, needs skilled technicians, and specific equipment. In this study, C_c was estimated using several soil parameters such as liquid limit (LL), plastic limit (PL), and initial void ratio (e₀). Estimating such parameters in laboratory is straight forward and needs substantially less time and cost compared to conventional tests to estimate C_c such as oedometer test. This study presents a novel prediction model for C_c of fine-grained soils using gene-expression programming (GEP). GEP is a biologically inspired technique capable of offering closed-form solution for the optimal solution. A database consisted of 108 different data points was used to develop the model. A closed-form equation solution was derived to estimate C_c based on LL, PL, and e₀. The performance of developed GEP-based model was evaluated through coefficient of determination (R²), root mean squared error (RMSE), and mean average error (MAE). High R² and low error values indicated the descent performance of the model. Furthermore, the model was evaluated using the additional performance measures and met all the suggested criteria. Furthermore, the model had a better performance in terms of R², RMSE, and MAE compared to most of existing models. It is expected that the developed model will decrease the time and cost associate with determining C_c of fine-grained soils.Keywords: evolutionary model, gene-expression programming (GEP), prediction, soil compression index, estimation, soil engineering, soil informatics, civil engineering, machine learning, data science, big data, soft computing, deep learning, forecasting, subject classification codes, construction informatics, computational intelligence (CI), artificial intelligence (AI), estimation

The connection of two phenomena - non-conservative friction forces and dissipation-induced instability can lead to many interesting engineering problems. The paper studies general material-dependent damping influence on dynamical instability of disc brake systems leading to brake squeal. The effect of general damping is demonstrated on a minimal and complex model of a disc brake. A complex system including material-dependent damping is defined in the commercial finite element software. The finite element model validated by experimental data on the brake-disc test bench is used to compute the influence of a pad and a disc damping variations on system stability by complex eigenvalue analysis. Analyzes show a significant sensitivity of the experimentally verified unstable mode of the system to the ratio of the damping between the disc and the friction material components.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article's main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

Human pluripotent stem cells (hPSCs) have widespread potential biomedical applications. There is a need for large-scale in vitro production of hPSCs, and optimal culture methods are vital in achieving this. Physiological oxygen (2% O2) improves key hPSCs attributes, including genomic integrity, viability, and clonogenicity, however, its impact on hPSC metabolism remains un-clear. Here, Selected Ion Flow Tube-Mass Spectrometry (SIFT-MS) was used to detect and quantify metabolic Volatile Organic Compounds (VOCs) in the headspace of hPSCs and their differentiated progeny. hPSCs were cultured in either 2% O2 or 21% O2. Media was collected from cell cultures and transferred into glass bottles for SIFT-MS measurement. The VOCs acetaldehyde and dimethyl sulfide (DMS)/ethanethiol were significantly increased in undifferentiated hPSCs compared to their differentiating counterparts, and these observations were more apparent in 2% O2. Pluripotent marker expression was consistent across both O2 concentrations tested. Transcript levels of ADH4, ADH5, and CYP2E1, encoding enzymes involved in converting ethanol to acetaldehyde, were upregulated in 2% O2, and chemical inhibition of ADH and CYP2E1 decreased acetaldehyde levels in hPSCs. Acetaldehyde and DMS/ethanethiol may be indicators of altered metabolism pathways in physiological oxygen culture conditions. The identification of non-destructive biomarkers for hPSC characterization has the potential to facilitate large-scale in vitro manufacture for future biomedical application.

The induced draft (ID) fan is important auxiliary equipment in the thermal power plant. It is of great significance to monitor the operation of the ID fan for safe and efficient production. In this paper, an adaptive warning model is proposed to detect early faults of ID fans. First, a non-parametric monitoring model is constructed to describe the normal operation states with the multivariate state estimation technique (MSET). Then, an early warning approach is presented to identify abnormal behaviors based on the results of the MSET model. As the performance of the MSET model is heavily influenced by the normal operation data in the historic memory matrix, an adaptive strategy is proposed by using the samples with a high data quality index (DQI) to manage the memory matrix and update the model. The proposed method is applied to a 300 MW coal-fired power plant for early fault detection, and it is compared with the model without an update. Results show that the proposed method can detect the fault earlier and more accurately.

In this paper, we proposed a novel saddle type FinFET (S-FinFET) to effectively solve problems occurring under the capacitor node of dynamic random-access memory (DRAM) cell and showed how its structure was superior to conventional S-FinFETs in terms of short channel effect (SCE), subthreshold slope (SS), and gate-induced drain leakage (GIDL). The proposed FinFET exhibited 4 times lower Ioff than modified S-FinFET called RFinFET with more improved DIBL characteristics while minimizing Ion reduction compared to RFinFET. Our results also confirmed that the proposed device showed improved DIBL and Ioff characteristics as gate channel length decreased.

Compressive sensing (CS) is a technique that allows a signal vector to be reconstructed with a number of linear measurements far fewer than its size. In this study, optical hybrid cryptography with simultaneous compressive sensing based on orthogonal matching pursuit (OMP) is proposed as an alternative solution to the two important problems in communications, namely, effective / efficient / signal processing and secure encryption/decrypton. The whole system is able to both compress and encrypt data with attack immunity.

Nine variants of regular lattice structures with different relative densities have been designed and successfully manufactured. The produced structures have been subjected to geometrical quality control, and the manufacturability of the implemented selective laser melting SLM technique has been assessed. It was found that the dimensions of the produced lattice struts differ from those of the designed struts. These deviations depend on the direction of geometrical evaluation. Additionally, the microstructures and phase compositions of the obtained structures were characterized and compared with those of conventionally produced 316L stainless steel. The microstructure analysis and X-Ray Diffraction XRD patterns revealed a single austenite phase in the SLM samples. Both a certain broadening and a displacement of the austenite peaks were observed due to residual stresses and a crystallographic texture induced by the SLM process. Furthermore, the mechanical behavior of the lattice structure material has been defined. It was demonstrated that under both quasi-static and dynamic testing, lattice structures with high relative densities are stretch-dominated, whereas those with low relative densities are bending-dominated. Moreover, the linear relationship between the energy absorption and relative density under dynamic loading conditions has been defined

Granular superconductivity at high temperatures in graphite can emerge at certain two-dimensional (2D) stacking faults (SFs) between regions with twisted (around the c-axis) or untwisted crystalline regions with Bernal (ABA...) and/or rhombohedral (ABCABCA...) stacking order. One way to observe experimentally such 2D superconductivity is to measure the frozen magnetic flux produced by a permanent current loop that remains after removing an external magnetic field applied normal to the SFs. Magnetic force microscopy was used to localize and characterize such a permanent current path found in one natural graphite sample out of ∼50 measured graphite samples of different origins. The position of the current path drifts with time and roughly follows a logarithmic time dependence similar to the one for flux creep in type II superconductors. We demonstrate that a ≃10nm deep scratch on the sample surface at the position of the current path causes a change in its location. A further scratch was enough to irreversibly destroy the remanent state of the sample at room temperature. Our studies clarify some of the reasons for the difficulties of finding a trapped flux in remanent state at room temperature in graphite samples with SFs.

Keywords: Chemical Intolerance, Drug Intolerance, Food Intolerance, QEESI, BREESI, Multiple Chemical Sensitivity, Toxicant-induced Loss of Tolerance, Prevalence

Since the discovery of the aggregation-induced emission effect in 2001, diaminodicyanoquinone derivatives (DADQs) have presented interesting fluorescence properties, allowing them to be considered fluorescent dyes capable of showing quantum yields above 90%. Besides, the diaminodiacyanoquinone core represents a versatile building block propense either to modification or integration into different systems to obtain and provide them unique photophysical features. Herein, we carried out a theoretical study on the fluorescence properties of three different diaminodicyanoquinodimethane systems. Therefore, time-dependent density functional theory (TD-DFT) was used to obtain the values associated with the dipole moments, oscillator strengths, and the conformational energies between the ground and the first excited states of each molecule. The results suggest that only two of the three studied systems possess significant luminescent properties. In a further stage, the theoretical insights were confirmed by means of experimental measurements, which not only retrieved the luminescence of the DADQs, but also suggest a preliminary and promising antibacterial activity of these systems.

This paper discusses approaches to the numerical integration of the coupled nonlinear Schrödinger equations system in case of few-mode wave propagation. The wave propagation assumes the propagation of up to nine modes of light in an optical fiber. In this case, the light propagation is described by the non-linear coupled Schrödinger equation system, where propagation of each mode is described by own Schrödinger equation with other modes interactions. In this case, the non-linear coupled Schrödinger equation system solving becomes increasingly complex, because each mode affects the propagation of other modes. The suggested solution is based on the direct numerical integration approach, which is based on a finite-difference integration scheme. The well-known explicit finite-difference integration scheme approach fails, due to the non-stability of the computing scheme. Due to this fact, the combined explicit/implicit finite-difference integration scheme, based on the implicit Crank–Nicolson finite-difference scheme, is used. It allows ensuring the stability of the computing scheme. Moreover, this approach allows separating the whole equation system on the independent equation system for each wave mode at each integration step. Additionally, the algorithm of numerical solution refining at each step and the integration method with automatic integration step selection are used. The suggested approach has performance gains (or resolutions) up to three or more orders of magnitude in comparison with the split-step Fourier method due to the fact that there is no need to produce direct and inverse Fourier transforms at each integration step. The main advantage of the proposed method is the ability to calculate the propagation of an arbitrary number of modes in the fiber.

In the present study, field observation wind data from the time of the wind turbine blade damage accident on Shiratakiyama Wind Farm were analyzed in detail. In parallel, high-resolution LES turbulence simulations were performed in order to examine the model’s ability to numerically reproduce terrain-induced turbulence. The comparison of the observed and simulated time series (1 second average values) from a 10 minute period from the time of the accident led to the conclusion that the settings of the horizontal grid resolution and time increment are important to numerically reproduce the terrain-induced turbulence that caused the wind turbine blade damage accident on Shiratakiyama Wind Farm. A spectral analysis of the same set of observed and simulated data revealed that the simulated data reproduced the energy cascade of the actual terrain-induced turbulence well.

Introduction: Wound healing is a multifaceted biological process, and diabetic wounds add more complexity to it. In diabetic wounds, the combination of chloroform fractions of Achyranthes aspera L. (A.aspera) leaves with β-Glucans has not been investigated. The additive effect of these two (A.aspera + β-Glucans) would benefit the inflammatory phase of diabetic wounds, as improper treatment will lead to chronic injuries. Therefore, the goal of this research work was to assess the in-vivo wound healing and anti-inflammatory effects of a combination of chloroform fractions of A.aspera leaves and β-Glucans in a variety of wound models in STZ-induced diabetic rats. Methods: Preliminary phytochemical analyses of A.aspera were conducted to identify various phytoconstituents in the test extract. Acute and sub-acute dermal toxicity tests of A.aspera were carried out on mice and rats, respectively, to see whether there were any abnormalities. Excision and incision wound models, cotton pellet-induced granuloma models, rat paw edema and burn wounds were used to test wound healing and anti-inflammatory actions. To induce diabetes, streptozotocin (STZ) was administered intraperitoneally at a dosage of 65 mg/kg (i.p.). A.aspera (10% w/w) and β-Glucans (2% w/w) ointments were tested separately and in combination for wound healing activities. Silver sulfadiazine (1 % w/w) ointment was used to treat the positive control groups. Excision wound model rats that had been treated with basic ointment were used as negative controls, as were incision wound model rats that had not been treated. A.aspera (400 mg/kg, po) and β-Glucans (30 mg/kg, po) were tested separately and in combination for anti-inflammatory efficacy. Positive control groups were given indomethacin (10 mg/kg, po) for cotton pellet-induced granuloma and rat paw oedema models. Negative controls for both anti-inflammatory activity models were provided 2% Tween 80. The groups were made up of six rats, and the treatments were given topically and orally to assess wound healing and anti-inflammatory effects. The levels of hydroxyproline and hexosamine and the antioxidant enzymes (SOD and CAT) in the granulation tissue were measured in excision wound model. Healed excision wound skin was examined histopathologically. Results: The A.aspera and β-Glucans combination resulted in a significant percentage of wound contraction and a shorter epithelialization time (P<0.01). The combination was found to be the most effective, with the highest percentage of edema reduction (55 %; p<0.01). The combination also exhibited favourable hydroxylamine, hexosamine and anti-oxidant profiles supported by histopathology data. Conclusion: This research showed that the immunomodulatory effect of β-Glucans had significantly enhanced the wound healing, anti-inflammatory, and anti-oxidant potential of A.aspera in diabetic wounds.

Individual plant cells are the building blocks for all plantae and artificially constructed plant biomaterials, like biocomposites. Secondary cell walls (SCWs) are a key component for mediating mechanical strength and stiffness in both living vascular plants and biocomposite materials. In this paper, we study the structure and biomechanics of cultured plant cells during the cellular developmental stages associated with SCW formation. We use a model culture system that induces transdifferentiation of Arabidopsis thaliana cells to xylem vessel elements, upon treatment with dexamethasone (DEX). We group the transdifferentiation process into three distinct stages, based on morphological observations of the cell walls. The first stage includes cells with only a primary cell wall (PCW), the second covers cells that have formed a SCW, and the third stage includes cells with a ruptured tonoplast and partially or fully degraded PCW. We adopt a multi-scale approach to study the mechanical properties of cells in these three stages. We perform large-scale indentations with a micro-compression system and nanoscale indentations through atomic force microscopy (AFM), in three different osmotic conditions. We introduce a spring-based model to deconvolve the competing stiffness contributions from turgor pressure, PCW, SCW and cytoplasm in the stiffness of differentiating cells. Prior to triggering differentiation, cells in hypotonic pressure conditions are significantly stiffer than cells in isotonic or hypertonic conditions, highlighting the dominant role of turgor pressure. Plasmolyzed cells with a SCW reach similar levels of stiffness as cells with maximum turgor pressure. The stiffness of the PCW in all of these conditions is lower than the stiffness of the fully-formed SCW. Our results provide the first experimental characterization of the mechanics of SCW formation at single cell level.

Appropriate estimation of soil settlement is of significant importance since it directly influences the performance of building and infrastructures that are built on soil. In particular, the settlement of fine-grained soils is critical because of low permeability and continuous settlement with time. Coefficient of consolidation (Cc) is a key parameter to estimate settlement of fine-grained soil layers. However, estimation of this parameter is time consuming, needs skilled technicians, and specific equipment. In this study, Cc was estimated using several soil parameters such as liquid limit (LL), plastic limit (PL), and initial void ratio (e0). Estimating such parameters in laboratory is straight forward and needs substantially less time and cost compared to conventional tests to estimate Cc such as Oedometer test. This study presents a novel prediction model for Cc of fine-grained soils using gene-expression programming (GEP). GEP is a biologically inspired technique capable of offering closed-form solution for the optimal solution. A database consisted of 108 different data points was used to develop the model. A closed-form equation solution was derived to estimate Cc based on LL, PL, and e0. The performance of developed GEP-based model was evaluated through coefficient of determination (R2), root mean squared error (RMSE), and mean average error (MAE). High R2 and low error values indicated the descent performance of the model. Furthermore, the model was evaluated using the additional performance measures and met all the suggested criteria. Furthermore, the model had a better performance in terms of R2, RMSE, and MAE compared to most of existing models. It is expected that the developed model will decrease the time and cost associate with determining Cc of fine-grained soils.

Seismic monitoring in areas where induced earthquakes could occur is a challenging topic for seismologists due to generally very low signal to noise ratio. Therefore, the seismological com-munity is devoting several efforts to the development of high-quality networks around the areas where fluid injection and storage and geothermal activities take place, also following the national induced seismicity monitoring guidelines. The use of advanced data-mining strategy, such as template matching filters, auto-similarity search and deep-learning approaches is recently further fostering such a monitoring enhancing the seismic catalogues and lowering the magnitude of completeness of these areas. In this framework, we carried out an experiment where a small-aperture seismic array was installed around the gas reservoir of Collalto, in North Italy. The continuous velocimetric data, acquired for 25 days, were analysed through the application of the optimized auto-similarity search technique FAST. The array was conceived as a cost-effective network, aimed at integrating, right above the gas storage site, the permanent high-resolution Collalto Seismic Network. The analysis allowed to detect micro-events down to magnitude Ml=-0.4 within a distance of ~15km from the array. Our results confirmed that the system based on the array installation and the FAST data-analysis might contribute to lower the magnitude of completeness around the site of about 0.7.

Aberrant neutrophil extracellular trap (NET) formation and the loss of barrier integrity in inflamed intestinal tissues have long been associated with inflammatory bowel disease (IBD). However, whether NETs alter intestinal epithelium permeability during colitis remains elusive. Here, we demonstrated that NETs promote the breakdown in intestinal barrier function for the pathogenesis of intestinal inflammation in mouse models of colitis. NETs were abundant in the colon of mice with colitis experimentally induced by dextran sulfate sodium (DSS) or 2,4,6-trinitrobenzene sulfonic acid (TNBS). Analysis of the intestinal barrier integrity revealed that NETs impaired gut permeability, enabling the initiation of luminal bacterial translocation and inflammation. Furthermore, NETs induced the apoptosis of epithelial cells and disrupted the integrity of tight junctions and adherens junctions. Intravenous administration of DNase I, an enzyme that dissolves the web-like DNA filaments of NETs, during colitis restored the mucosal barrier integrity which reduced the dissemination of luminal bacteria, and attenuated intestinal inflammation in both DSS and TNBS models. We conclude that NETs serve a detrimental factor in the gut epithelial barrier function leading to the pathogenesis of mucosal inflammation during acute colitis.

Meteorites represent the recoverable portions of asteroids occurring between Mars and Jupiter within the solar system that reach the surface of the Earth. Meteorites are rare extraterrestrial objects studied extensively to improve understanding of planetary evolution. In this work, calibration-free laser-induced breakdown spectroscopy (CF-LIBS) evaluates quantitative elemental and molecular analysis of the Dergaon meteorite, an H 4-5 chondrite fall sample, Assam, India. Spectral signatures of H, N, O, Na, Mg, Al, Si, P, K, Ca, Ti, Cr, Mn, Fe, Co, Ni, Ir, are measured. Along with the atomic emission, this work reports as well molecular emission from FeO molecules. The concentration of the measured elements obtained using CF-LIBS are in close agreement with earlier reports. The elements H, N and O and their concentrations are estimated using CF-LIBS for the first time. This study applies laser spectroscopy to establish presence of Ni, Cr, Co, and Ir in meteorites. Elemental analysis forms the basis for establishment of potential molecular composition of the Dergaon meteorite. Moreover, the elemental analysis approach bodes well for in-situ analyses of extraterrestrial objects including applications in planetary rover missions.

Chemotherapy-induced peripheral neuropathy (CIPN) develops as a challenging nerve-damaging adverse effect of anticancer drugs used in chemotherapy. The disorder may require a dose reduction of chemo-therapy and its most common sensory symptoms are severe pain, tingling, and numbness in the hands and feet. CIPN affects dramatically the patient's quality of life (QoL). Pain and sensory abnormalities may occur for months, or even years after the termination of chemotherapy. This disease has complicated pathophysiology featured by underlying mechanisms not completely known. Although many pharmaco-logical and non-pharmacological therapeutic approaches have been tested to overcome these symptoms, there is currently no standardized cure to prevent or treat CIPN. According to current guidelines, Duloxe-tine is the only recommended agent for painful neuropathic symptoms. Therefore, finding effective thera-pies for CIPN is mandatory. The purpose of this review is to dissect CIPN, the target and immunothera-py-based approaches to this disorder, as well as to offer new insights for novel therapeutic perspectives.

In this article, we investigate limitations of importing methods based on algorithmic information theory from monoplex networks into multidimensional networks (such as multilayer networks) that have a large number of extra dimensions (i.e., aspects). In the worst-case scenario, it has been previously shown that node-aligned multidimensional networks with non-uniform multidimensional spaces can display exponentially larger algorithmic information (or lossless compressibility) distortions with respect to their isomorphic monoplex networks, so that these distortions grow at least linearly with the number of extra dimensions. In the present article, we demonstrate that node-unaligned multidimensional networks, either with uniform or non-uniform multidimensional spaces, can also display exponentially larger algorithmic information distortions with respect to their isomorphic monoplex networks. However, unlike the node-aligned non-uniform case studied in previous work, these distortions in the node-unaligned case grow at least exponentially with the number of extra dimensions. On the other hand, for node-aligned multidimensional networks with uniform multidimensional spaces, we demonstrate that any distortion can only grow up to a logarithmic order of the number of extra dimensions. Thus, these results establish that isomorphisms between finite multidimensional networks and finite monoplex networks do not preserve algorithmic information in general and highlight that the algorithmic information of the multidimensional space itself needs to be taken into account in multidimensional network complexity analysis.

We developed two human induced pluripotent stem cell (hiPSC)/human embryonic stem cell-specific glycan-recognizing mouse antibodies, R-10G and R-17F, using the Tic (JCRB1331) hiPSC line as an antigen. R-10G recognizes a low-sulfate keratan sulfate, and R-17F recognizes lacto-N-fucopentaose-1. To evaluate the general characteristics of stem cell glycans, we used the hiPSC line 201B7 (HPS0063), a prototype iPSC line. Using an R-10G affinity column, an R-10G-binding protein was isolated. The protein yielded a single but very broad band from 480 to 1,236 kDa by blue native gel electrophoresis. After trypsin digestion, the protein was identified as podocalyxin by liquid chromatography/mass spectrometry. According to Western blotting, the protein reacted with R-10G and R-17F. The R-10G positive band was resistant to digestion with glycan-degrading enzymes, including peptide N-glycanase, but the intensity of the band was decreased significantly by digestion with keratanase, keratanase II, and endo-β-galactosidase, suggesting the R-10G epitope to be a keratan sulfate. These results suggest that keratan sulfate-type epitopes are shared by hiPSCs. However, the keratan sulfate from 201B7 cells contained a polylactosamine disaccharide unit (Galβ1-4GlcNAc) at a significant frequency, whereas that from Tic cells consisted mostly of keratan sulfate disaccharide units (Galβ1-4GlcNAc(6S)). In addition, the abundance of the R-10G epitope was significantly lower in 201B7 cells than in Tic cells.

The statistical analysis of impact of the top 50 solar flares of X-class (1997-2023) on the global seismic activity, as well as on the earthquake preparation zones located in illuminated part of the globe and in the area of 5000 km radius around the subsolar point was carried out. It is shown by a method of epoch superposition that for all cases the increase of seismicity is observed, especially in the region around the subsolar point (up to 38%) during 10 days after the solar flare in comparison with preceding 10 days. The case study of aftershock sequence of strong M=9.1 earthquake (Su-matra-Andaman Islands, 26.12.2004) after the solar flare of X7.2 class (20.01.2005) demonstrated that the number of aftershocks with magnitude M≥2.5 increases more than 20 times after the solar flare with a delay of 7 days. For the case of the Darfield earthquake (M=7.1, 04.09.2010, New Zealand) it was shown that strong solar flares of class X and M probably triggered two strong aftershocks (M>6) with the same delay of 6 days on the Port Hills fault, which is the most sensitive to external electromagnetic impact from point of view of the fault electrical conductivity and orientation. Based on the obtained results the possible application of natural electromagnetic triggering of earthquakes is discussed for a short-term earthquake prediction using confidently recorded strong external electromagnetic triggering impacts on the specific earthquake preparation zones, as well as ionospheric perturbations due to aerosol emission from the earthquake sources recorded by satellites.

MiRNAs are 20-22 nucleotide long single-stranded non-coding RNA sequences, which can regulate post transcriptional activity of mRNA by binding with it at 3’UTR region (untranslated region). Thus deregulation of miRNA expression is responsible for dysregulating mRNA function which contributes in developing various diseases as well as cancerous phenotypes. Alteration of single nucleotide in miRNA sequence is one of the reasons behind deregulation of miRNA expression. The most frequent carcinoma in current day is breast cancer which causes a high mortality among women around the world as well as India. Despite of the advancement of diagnostic tools, strategies and treatment, the cases of breast cancer is increasing every year. There are plenty of biomarkers like ER, PR, Her2, Ki-67, etc available which are frequently used in diagnosis and treatment of breast cancer. After the discovery of MiRNA in 1993 in Caenorhabiditis elegans, it is attracting all the limelight in diagnosis and treatment of different carcinomas as well as breast cancer. In this review we will discuss on involvement of different types of MiRNAs and miR SNPs in breast cancer occurrence and susceptibility in a detailed manner.

Adult stem cells (ASCs) can be cultured with difficulty from most tissues, often requiring chemical or transgenic modification to achieve adequate quantities. We show here that mouse primary fibroblasts grown in suspension change from the elongated and flattened morphology observed under standard adherent culture conditions generating rounded cells with large nuclei and scant cytoplasm expressing the mesenchymal stem cell (MSC) marker (Sca1; Ly6A) within 24hrs. Based on this initial observation, we describe here a suspension culture method that, irrespective of the lineage used, mouse fibroblast, primary human somatic cells (fibroblasts, hepatocytes and keratinocytes), is capable of generating a high yield of cells in spheroid form which display expression of ASCs surface markers, circumventing the anoikis which often occurs at this stage. Moreover, mouse fibroblasts-derived spheroids can be differentiated into adipogenic and osteogenic lineages. Analysis of single cell RNA sequence data identified 8 distinct cell clusters with one in particular comprising approximately 10% of the cells showing high levels of proliferative capacity expressing high levels of genes related to MSCs and self-renewal as well as extracellular matrix (ECM). We believe the rapid, high-yield generation of proliferative, multi-potent ASC-like cells by the process we term suspension-induced stem cell transition (SIST) could have significant implications for regenerative medicine.

Limb girdle muscular dystrophies (LGMD), caused by mutations in 29 different genes, are the fourth most prevalent group of genetic muscle diseases, leading to progressive weakness and atrophy of the skeletal muscles. Although the link between LGMD and their genetic origins has been determined, LGMD still represent an unmet medical need. In this paper, we describe a platform for modeling LGMD based on the use of human induced pluripotent stem cells (hiPSC). Thanks to the self-renewing and pluripotency properties of hiPSC, this platform provides an alternative and renewable source of skeletal muscle cells (skMC) to primary, immortalized or overexpressing cells. We report that skMC derived from hiPSC express the majority of the genes and proteins causing LGMD. As a proof of concept, we demonstrate the importance of this cellular model for studying LGMDR9 by evaluating disease-specific phenotypes in skMC derived from hiPSC obtained from four patients.

Abstract: High-dose-rate interstitial brachytherapy (HDR-ISBT) has recently come to be considered one of the most effective treatments for oral cancer. On the other hand, it is important to note that radiation therapy has some side effects. Especially, radiation-induced malignancy is probably the most serious complication affecting long-term survivors. We report a case of a radiation-induced undifferentiated spindle cell sarcoma that developed following HDR-ISBT for tongue squamous cell carcinoma (SCC). A 39-year-old woman with right tongue SCC underwent HDR-ISBT (60 Gy, 10 fractions, 8 days) treatment. Five years and one month later, a tumor had developed at the primary site. Surgery was performed for the tumor, which was histopathologically diagnosed as an undifferentiated spindle cell sarcoma. That was distinct from the squamous cell origin of the primary cancer. According to recently established criteria for radiation-induced malignancy, this case was classified as a radiation-induced sarcoma. A search of the literature revealed no previous report of radiation-induced malignancy following HDR-ISBT for tongue cancer.

Degenerative spinal cord (SC) compression is a frequent pathological condition with increasing prevalence throughout aging. Initial non-myelopathic cervical SC compression (NMDC) might progress over time into potentially irreversible degenerative cervical myelopathy (DCM). While quantitative MRI (qMRI) techniques demonstrated the ability to depict intrinsic tissue properties, longitudinal in-vivo biomarkers to identify NMDC patients who will eventually develop DCM are still missing. Thus, we aim to review the ability of qMRI techniques (such as diffusion MRI, diffusion tensor imaging (DTI), magnetization transfer (MT) imaging, magnetic resonance spec-troscopy (1H-MRS)) to serve as prognostic markers in NMDC. While DTI in NMDC patients con-sistently detected lower fractional anisotropy and higher mean diffusivity at compressed levels caused by demyelination and axonal injury, MT and 1H-MRS along with advanced and tract-specific diffusion MRI recently revealed microstructural alterations also rostrally pointing to Wallerian degeneration. Recent studies also disclosed significant relationship between micro-structural damage and functional deficits, assessed by qMRI and electrophysiology, respectively. Thus, tract-specific qMRI in combination with electrophysiology critically extend our under-standing of the underlying pathophysiology of degenerative SC compression and may provide predictive markers of DCM development for accurate patient management. However, the prog-nostic value must be validated in longitudinal studies.

Background: Strong indicators of inflammation, such as C-reactive protein (CRP), hypersensitive CRP (hs-CRP), and a series of hematological indices, including platelet to lymphocyte ratio (PLR), neutrophil to lymphocyte ratio (NLR), hematocrit (HCT) and red blood cell distribution width (RDW), are regarded related with the incidence of contrast induced nephropathy (CIN) closely. Whereas, it remains unclear whether they can function as predictors of CIN onset. The objective of this meta-analysis was to determine the relationship between above indicators and CIN incidence among patients receiving coronary intervention. Methods: Clinical studies were retrieved from the electronic databases of PubMed, EMBASE, Google Scholar, Clinical Trials, and science direct from their inception to June 3rd, 2020. Meta-analysis was performed on pool eligible studies. Two reviewers screened all titles and abstracts and independently assessed all articles. Results: A total of 26 studies involving 29,454 patients were included in the meta-analysis. Pooled analysis results revealed that patients with higher CRP (odds ratio [OR]=1.06, 95% confidence interval [CI]: 1.01–1.12, P=0.02), hs-CRP (OR=1.03, 95% CI: 1.01–1.06, P=0.004), NLR (OR=1.11, 95% CI: 1.01–1.20, P=0.02), RDW (OR=1.35, 95% CI: 1.19–1.53, P<0.00001), and lower HCT (OR=0.94, 95% CI: 0.92–0.97, P=0.0003) all exhibited significantly higher CIN rates, but there was no significant association between PLR and CIN risk (OR=1.12, 95% CI: 0.99–1.26, P=0.07). Conclusion: The meta-analysis reported here demonstrates that pre-angiography CRP/hs-CRP and some hematological indices are associated with CIN.

Although lithium-ion batteries have extensively been used in various applications because of their high energy capacity, fracture and failure, the by-products of large strains and stresses caused by fast charging and discharging need yet to be addressed. The size effects on the mechanical behavior of the nano-sized structures are significant; however, the classical elasticity theory may not consider such effects. On the other hand, surface stress theory, as a robust and potential theory, is suitable in considering size effects in nano-scale structures. Therefore, in this paper, in order to involve the surface stress effects on the fracture behavior of Li-ion batteries, the following steps are taken. Firstly, a phase-field model is used to determine the evolution of the concentration profile. Subsequently, the stress distribution is obtained by using the surface stress theory combined with chemical equations for a planar electrode. Afterward, by using the weight function method for an edge crack in the plate, the stress intensity factor is derived for all time steps and possible crack lengths during the process. It is found that with increasing phase boundary thickness parameter or decreasing phase-separation phenomenon, the surface mechanics parameters become more influential. Furthermore, in the presence of positive surface stress, the diffusion-induced stress distribution decreases, which in turn reduces the stress intensity factor. In addition, in this paper, the two states of surface stress are compared either for elastic or total strain. Concerning stresses and concentrations, the results indicate a big difference at the beginning of the deintercalation process showing, in particular, 2% for stresses, but the differences diminish gradually.

China historically exhibits spatial differentiation from population distribution to ecological or economic development, and the forest pest control work is an epitome of this tendency. In recent times, global warming, man-made monoculture tree plantations, increasing human population density and intensified international trade aggravate forest pest outbreaks. Although Chinese government has complied with the internationally recommended practices, few stones remain unturned due to existing differential regional imbalance of forest pest distribution and control abilities. Evidence shows that the high-income provinces in the south have taken advantage of economic and technological superiority, resulting in the adoption of more efficient pest-control measures. To the contrary, in economically underdeveloped provinces of the northwest, a paucity of financial support has led to serious threats of pest damage that almost mirrored the demarcations of the Hu Huanyong Line. In this paper, we propose introducing public-private partnership (PPP) model into forest pest control and combining the national strategies to enact regional prevention measures in order to break the current spatially differentiated trends in China.

This article discusses laser-induced laboratory-air plasma measurements and analysis of hydroxyl (OH) ultraviolet spectra. New experiments with Q-switched laser pulses illustrate occurrence of molecular recombination spectra for time delays of the order of several dozen of microseconds after plasma initiation. The computation of the emission spectra utilizes line strength data that are communicated as a supplementary file. Applications of detailed OH computations include laser-induced plasma and combustion analyses, to name but two applications.

NASA’s ICESat-2space-borne photon-counting lidar mission is providing global elevation measurements that will provide significant benefits to a variety of bio-geoscience research applications. Given the novelty of elevation and the derived data products from the ICESat-2 mission, the research community needs software tools that can facilitate photon-level analyses to support product validation and development new analysis methods. Here, we describe PhotonLabeler, a free graphic user interface (GUI) for manual labeling and visualization of ICESat-2 Geolocated Photon data (ATL03). Developed in MATLAB, the GUI facilitates the reading and display of ATL03 Hierarchical Data Format (HDF) files, the manual labeling of individual photons into target classes of choice using a number of point selections tools and enables eventual saving of labeled data in ASCII format. Other capabilities include saving and loading of labeling sessions to manage labeling tasks over time. We expect labeled data generated using the application to serve two main purposes. First, serve as ground truth for validating various products from ICESat-2 mission, especially for study sites around the world that do not have existing reference datasets such as airborne lidar. Second, serve as training and validation data in the development of new algorithms for generating various ICESat-2 data products. We demonstrate the first use case through a validation case study for the land and vegetation product (ATL08), which provides canopy and terrain height estimates, over two sites. For the first site, located in northwestern Zambia, we used ICESat-2 ATL03 data acquired at night and for our second site in Texas, US, we used ATL03 data acquired during the day. The PhotonLabeler application is freely available as a compiled MATLAB binary to enable free access and utilization by interested researchers.

Calcareous sand deposits are widely distributed along the shoreline in ropical and subtropical regions. Microbially induced calcite precipitation treatment (MICP) is a relatively new method to improve the stiffness and strength of the soil. Little is known about the small-strain shear modulus and damping ratio of MICP-treated calcareous sand, which are two crucial parameters for the prediction of the dynamic behavior of soil. A series of resonant column tests are performed to investigate the dynamic performance of MICP-treated calcareous sand, with special attention paid to the influence of treatment duration and confining stress on the stiffness and damping characteristics. The relationship between the initial dynamic shear modulus and unconfined compressive strength is analyzed. Additionally, the empirical equations of the reference shear strain between treatment duration and confining stress are given. The G/G0 of MICP-cemented calcareous sand presents a higher strain sensitivity than that of untreated sand, and its attenuation pattern can be described by Hardin-Drnevich model. The σc has an apparent effect on the degradation characteristics of the dynamic shear modulus of MICP-treated calcareous sand with a low cementation level, however, its effect decreases with the increasing treatment duration. The relationship between the reference shear strain and the treatment duration and confining stress can be described by a power and a linear formula, respectively.

In this paper, we synthesized MC(BeA-co-MMA) copolymer microcapsules through suspension polymerization. The pendent n-behenyl group of BeA is highly crystalline, and it acts as the side-chain in the structure of BeA-co-MMA copolymer. The highly crystalline n-behenyl side-chain provides BeA-co-MMA copolymer thermal-energy-storage capacity. In order to investigate the correlation between thermal properties and crystal structure of BeA-co-MMA copolymer, the effects of monomer ratio, temperature changing and changing rate, as well as synthesis method were discussed. The monomer ratio influenced crystal transition behavior and thermal properties greatly. The DSC results proved that when the monomer ratio of BeA and MMA was 3:1, MC(BeA-co-MMA)3 showed the highest average phase change enthalpy ΔH (105.1 J·g–1). It indicated that the n-behenyl side-chain formed relatively perfect crystal region, which ensured a high energy storage capacity of copolymer. All the DSC and SAXS results proved that the amount of BeA had a strong effect on the thermal-energy-storage capacity of copolymer and the long spacing of crystals, but barely on the crystal lamella. It was found that MMA units worked like defects in the n-behenyl side-chain crystal structure of BeA-co-MMA copolymer. Therefore, a lower fraction of MMA, that is, a higher fraction of BeA contributed to a higher crystallinity of BeA-co-MMA copolymer for providing a better energy storage capacity and thermoregulation property. ST(BeA-co-MMA) copolymer sheets with the same ingredients as microcapsules were also prepared through light-induced polymerization aiming at clarifying the effect of synthesis method. The results proved that synthesis method mainly influenced the copolymer chemical component, but lightly on the crystal packing of n-behenyl side-chain.

We report on space-selective crystallization of congruent and polar Sr2TiSi2O8 crystals in a stoichiometric SrO-TiO2-SiO2 glass induced by (1030 nm, 300 fs) femtosecond laser irradiation. This allows us to compare with non-congruent laser induced crystallization of polar LiNbO3, in non stoichiometric Li2O-Nb2O5-SiO2 glass and gain information on the mechanism of nanocrystals orientation with the laser polarization that we pointed out previously. Using scanning electron microscopy (SEM), Second-harmonic generation (SHG) and electron backscattered diffraction (EBSD), we studied the laser induced crystallization according to the laser processing parameters (pulse energy, pulse repetition rate, scanning speed). We found 1) a domain where the laser track is filled with crystals not perfectly textured (low energy), 2) a domain where an amorphous volume remain surrounded by a crystallized shell (high energy). This arises from Sr out-diffusion and may gives rise to crystallization of both SrTiO3 and Sr2TiSi2O8 phases at low speed. In the one-phase domain (at higher speed), it is found the possibility to elaborate a tube with a perfect fresnoite texture. Significant difference in size and morphology whereas crystallization threshold remains similar are discussed based on glases thermal propeties. Contrarily to Li2O-Nb2O5-SiO2 (LNS) glass, no domain of oriented nanocrystallization controlled by the laser polarization has been found in SrO-TiO2-SiO2 (STS) glass, which is attributed to the larger crystallization speed in STS glass. No nanogratings have also been found that is likely due to the congruency of the glass.

Solar assisted hybrid cooling systems are promising for the energy saving of refrigeration systems. In most cases, the solar thermal gain is only able to power the heat-driven process of facilities in part of the working period. Therefore, the reduction of compressor power strongly depends upon the duration of heat-driven processes, which has not been addressed properly. Motivated by such knowledge gap, the thermodynamic understanding of solar assisted hybrid cooling systems is deepened through considering the duration in heat-driven processes. Three absorption-compression integrated cooling cycles were taken as examples. It is found that optimal parameters, e.g., inter-stage pressure and temperature, corresponding to various performance indicators trend to be identical, as the duration of heat-driven processes is taken into account. Furthermore, the optimal parameter for different working conditions was obtained. It is displayed that the dimensionless optimal intermediate temperature of layout with the cascade condensation process varies slightly, e.g., 4%, for different conditions. Moreover, the fall of compressor power in entire working periods is nearly independent upon the intermediate temperature. The paper is favorable for the efficient design and operation of solar assisted hybrid cooling systems.

The QBIT theory is an attempt toward solving the problem of consciousness in the light of Quantum mechanics, Biology, Information theory, and Thermodynamics. “Internal representation” is a key concept in the QBIT theory of consciousness. An internal representation is defined as a pack of information (within a cognitive system) that represents an external stimulus.The QBIT theory suggests that when robustness of an internal representation exceeds a certain threshold, a conscious experience (or a quale) is generated. In this paper, the concept of internal representation and its relation with consciousness is explored.

In this work, we have developed a non-ordinary state-based peridynamic model for multiple crack initiation and propagation due to compression-compression fatigue load. In each loading cycle, the fatigue loading is redistributed among the peridynamic solid body, leading to the progressive fatigue damage initiation and propagation in an autonomous fashion. The proposed fatigue model parameters are firstly validated by 3D numerical benchmark tests, and then it is applied to simulate widespread fatigue damage evolution of the aircraft wing corner box. The modified constitutive damage model has been implemented into the peridynamics framework at finite strain. Furthermore, the criterion algorithm from multiple initiation to propagation is discussed. It is shown that the numerical results obtained from peridynamics simulations are in general agreement with those from the experiment data. The comparison of experimental and numerical results indicates that the proposed non-ordinary state-based peridynamics fatigue model has the ability to capture the multiple crack initiation and propagation and other features of the aluminium alloy material.

In this work, the parameters of plasma (electron temperature (T_e), electron density n_e, plasma frequency (f_p) , Debye length (λ_D) and Debye number (N_D)) have been studied by using the spectrometer that collect the spectrum of Laser produce Cadmium telluride plasma at different energies. The results of electron temperature for CdTe range 0.93-1.18 eV also the electron density 5 × 10¹⁰ – 3.8 × 10¹¹ cm^-3 have been measured under vacuum reaching 2.5 × 10^-2 mbar .Optical properties of CdTe were determined through the optical transmission method using ultraviolet visible spectrophotometer within the range 190 – 1100 nm.

Nowadays, information security is a challenge especially when transmitted or shared in public clouds. Many of researchers have been proposed technique which fails to provide data integrity, security, authentication and another issue related to sensitivity data. The most common techniques were used to protect data during transmission on public cloud are cryptography, steganography, and compression. The proposed scheme suggests an entirely new approach for data security on public cloud. Authors have suggested an entirely new approach that completely makes secret data invisible behind carrier object and it is not been detected with the image performance parameters like PSNR, MSE, entropy and others. The details of results are explain in result section of paper. Proposed technique have better outcome than any other existing technique as a security mechanism on a public cloud. Primary focus of suggested approach is to minimize integrity loss of public storage data due to unrestricted access rights by uses. To improve reusability of carrier even after data concealed is really a challenging task and achieved through suggested approach.

The cuttlebone-like structure is a complex porous bionic structure with asymmetric sinusoidal S-shaped wall structure connecting laminar septa, and studies have shown that the cuttlebone-like structure has light weight, high strength and excellent energy absorption capability. It has become an important research to investigate the mechanical mechanism of cuttlebone-like structure and to design a bionic structure beyond nature structure based on it. In order to investigate the mechanical properties of the static compression and shearing processes of the cuttlebone-like structure, this paper establishes theoretical formulas and analyzes the influence of dimensionless parameters such as height-to-thickness ratio $\lambda$, period-to-thickness ratio $\xi$ and amplitude to period ratio $\eta$ on the compression and shearing processes with the help of ABAQUS finite element software.The parameter sensitivity analysis method was used to compare the important influence degree of each dimensionless parameter on the mechanical properties of the structure and to determine the relative optimal parameters of the structural mechanical properties under compression and shearing. Based on the relatively optimal parameter of the cuttlebone-like structure, the cross-sectional geometry of the structure is improved to build a new cuttlebone-like structure.The experimental results showed that the new cuttlebone-like structure with revised cross-section improved the mechanical properties of the cuttlebone-like structure.The study results are of theoretical guidance to enhance the mechanical properties and geometric design of cuttlebone-like structures.

Exercise induced bronchoconstriction (EIB) is a common complication of athletes and individuals who exercise regularly. It is estimated that about 90% of patients with underlying asthma experience EIB. Sex differences in the prevalence of asthma have been widely reported, with higher rates in boys vs. girls before puberty, and higher rates in women than men after puberty. Because atopy has been reported to occur at higher rates in athletes than in non-athletes, in this study we investigated sex differences in EIB and atopy in athletes. A systematic literature review identified 60 studies evaluating EIB and/or atopy in post-pubertal adult athletes (n=7501). Collectively, these studies reported: 1) a 23% prevalence of EIB in athletes; 2) a higher prevalence of atopy in male athletes vs. females; 3) a higher prevalence of atopy in athletes with EIB; and 4) a significantly higher rate of atopic EIB in male vs. female athletes. Our analysis indicates that the physiological changes that occur during exercise may differentially affect male and female athletes, and suggest an interaction between male sex, exercise, and atopic status in the course of EIB. Understanding these sex differences is important to provide personalized management plans to athletes with underlying asthma and/or atopy.

The soil-borne pathogens, particularly Fusarium oxysporum f. sp. niveum (FON) and southern root-knot nematode (RKN, Meloidogyne incognita) are the major threat to watermelon production in the south-eastern United States. The role of soil micronutrients on induced resistance (IR) to plant diseases is well-documented in soil-based mediums. However, soil-based mediums limit the determination of the role(s) of individual micronutrients in IR. In this manuscript, we utilized hydroponics to assess the effect of controlled application of micronutrient, including iron (Fe), manganese (Mn), and zinc (Zn) on the expression of some IR genes (PR1, PR5, and NPR1 from salicylic acid (SA) pathway, and VSP, PDF, and LOX genes from jasmonic acid (JA) pathway) in watermelon seedlings upon inoculation with either FON or RKN or both. Plants were treated with higher (3X) or lower (0.5X) concentrations of micronutrients in Steiner solution (X= standard dose of micronutrient) for 7 days in a hydroponics system under greenhouse conditions. A subset of micronutrient-treated plants was inoculated (on the 8th day of micronutrient application) with FON and RKN (single and mixed). The expression of the IR genes in treated and control samples were evaluated using qRT-PCR. Although, significant phenotypic differences were not observed with respect to the severity of wilt symptoms or RKN galling with any of the micro-nutrient treatments within the 30 day-experimental-period, differences in the induction of IR genes were observed. However, the level of gene expression varied with sampling period, type and concentration of micro-nutrients ap-plied, and pathogen-inoculation. In the absence of pathogens, no significant changes were observed in the expression level of IR genes on 7th day of micronutrient treatment. However, pathogen inoculation affected the expression levels of the IR genes at 3-day post-inoculation. In FON inoculated plants, PDF was upregulated in high Fe treatment, whereas in RKN inoculated plants, low Mn treatment resulted in up-regulation of VSP. In the case of mixed inoculation with FON and RKN, the plants with low Zn treatment resulted in the upregulation of PR1. These observations suggest that the type and concentration of micronutrients in watermelon may potentially induce systemic resistance against FON and RKN through SA and JA pathways.

Centromeres, the chromosomal loci where spindle fibers attach during cell division to segregate chromosomes, are typically found within satellite arrays in plants and animals. Satellite arrays have been difficult to analyze because they comprise megabases of tandem head-to-tail highly repeated DNA sequences. Much evidence suggests that centromeres are epigenetically defined by the location of nucleosomes containing the centromere-specific histone H3 variant cenH3, independently of the DNA sequences where they are located; however, the reason that cenH3 nucleosomes are generally found on rapidly evolving satellite arrays has remained unclear. Recently, long read sequencing technology has clarified the structures of satellite arrays and sparked rethinking of how they evolve, while new experiments and analyses have helped bring both understanding and further speculation about the role these highly repeated sequences play in centromere identification.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

Age-related macular degeneration is a progressive retinal disease that is associated with factors such as oxidative stress, decreased phagocytic activity, and inflammation. In this study, we evaluated the protective effects of SIG-1451, a non-steroidal anti-inflammatory drug developed for treating atopic dermatitis and known to inhibit toll-like receptor 4, on light-induced photoreceptor degeneration. SIG-1451 was intraperitoneally injected into rats once a day before exposure to 1000 lx light for 24 h; one day later, optical coherence tomography showed a decrease in retinal thickness, and electroretinogram (ERG) amplitude was also found to have decreased 3 d after light exposure. Moreover, SIG-1451 protected against this decrease in retinal thickness and increase in ERG am-plitude. One day after light exposure, upregulation of inflammatory response-related genes was observed, and SIG-1451 was found to inhibit this upregulation. Iba-1, a microglial marker, was suppressed in SIG-1451-injected rats. To investigate the molecular mechanism underlying these effects, we used lipopolysaccharide (LPS)-stimulated rat immortalised Müller cells. The upregu-lation of C-C motif chemokine 2　by LPS stimulation was significantly inhibited by SIG-1451 treatment, and western blot analysis revealed a decrease in phosphorylated I-κB levels. These results indicate that SIG-1451 protects photoreceptor cells by attenuating light damage progression through inhibiting inflammatory responses.

Plasmodium falciparum dihydroorotate dehydrogenase (PfDODH) is one of the enzymes currently explored in the treatment of malaria. Although there is currently no clinically approved drug targeting PfDODH, many of the compounds in clinical trials have [1, 2, 4,] triazolo [1, 5-a] pyrimidin-7-amine backbone structure. This study sought to design new compounds from the fragments of known experimental inhibitors of PfDODH. Nine experimental compounds retrieved from Drug Bank online were downloaded and broken into fragments using Schrodinger power shell; the fragments were recombined to generate new ligand structures using BREED algorithm. The new compounds were docked with PfDODH crystal structure, after which the compounds were filtered with extensive drug-likeness and toxicity parameters. A 2D-QSAR model was built using the multiple linear regression method and externally validated. The compounds electronic behaviours were studied using DFT calculations. Structural investigation of the six designed compounds, which had lower binding energies than the standard inhibitors, showed that five of them had [1, 2, 4,] triazolo [1, 5-a] pyrimidin-7-amine moieties and interacted with essential residues at the PfDODH binding site. In addition to their drug-like and pharmacokinetic properties, they also showed minimal toxicities. The externally validated 2D-QSAR model with R² and Q² values of 0.6852 and 0.6691, confirmed the inhibitory prowess of these compounds against PfDODH. The DFT calculations showed regions of the molecules prone to electrophilic and nucleophilic attack. The current study thus provides insight into the development of a new set of potent PfDODH inhibitors.

The cold-formed steel sections are becoming popular for different steel structures because it has a high resistance against the different straining actions with minimum weight compared with hard steel sections. Recently, the perforated cold-formed steel (PCFS) sections are used in many applications such as storage perforated uprights racks. Experimental research into the behaviour of steel storage rack uprights subjected to axial compression is presented in this paper. The material qualities of cold-formed steel uprights were determined by tensile tests. The seventeen perforated specimens were examined under axial compression, with five different cross-sections, three different web heights and thicknesses, and varying lengths. The study's goals are to find out how perforations affect the performance and failure mode of steel storage rack uprights, discuss the interaction of distortional and global buckling, and verify the accuracy of using the Direct Strength Method (DSM) for predicting the ultimate strength of uprights failing in buckling interactions for perforated uprights. It is found that the failure modes of perforated specimens with stiffeners generally cannot be well predicted by the Direct Strength Method. But when the modifications proposed by Xianzhong Zhao etc. al. are used, their accuracy is acceptable.

Large-area nanostructuring of glasses using intense laser beam remains a difficult task due to the extreme non-linear absorption of the laser energy by the material. Precise optimization of the process parameters is essential for fabricating nanostructures with large area coverage. In this study, we report the findings on creating high spatial frequency LIPSS (HSFL) on borosilicate glass through direct laser writing, using a femtosecond laser with a wavelength λ = 800 nm, pulse duration τ = 35 fs, and repetition frequency frep = 1 kHz. The orientation of the HSFL was found to be parallel to the electric field vector. We measured the single pulse ablation threshold (Fth=3.87±0.26 J/cm2) and incubation factor (S=0.68±0.03) of Borosilicate glasses for precise control for large area surface structuring. Single-spot experiments indicate that uniform LIPSS formation is limited by melt formation inside the irradiated area for higher fluence and a larger number of irradiated laser pulses. The orientation of the scan axis with the laser beam polarization is found to be significantly influencing the uniformity of the large area processing. We found that the orientation of the scan axis with the laser beam polarization significantly affects the uniformity of large-area processing, with redeposition and melt formation being higher when the scan axis is perpendicular to the laser beam polarization. Large-area processing of the borosilicate glass surface is done by line-by-line scanning over the surface with a scan orientation parallel to the laser beam polarization. The optical characterization reveals that the transmittance and reflectance of the borosilicate glass decreased significantly after processing. Also, the wettability of the surface has been changed from hydrophilic to super hydrophilic after processing. These chemical contamination-free and uniformly distributed structures have potential applications in optics, microfluidics, photovoltaics, and biomaterials.

This research aims to study the ultimate limit state (ULS) behaviour of stiffened panel under longitudinal compression by non-linear finite element method (NLFEM). There are different types of stiffeners being used in shipbuilding i.e. T-bar, flat-bar and angle-bar. However, this research focuses on the ultimate compressive strength behaviour of flat-bar stiffened panel. A total of 420 of reliable scenarios of flat-bar stiffened panel are selected for numerical simulation by ANSYS NLFEM. The ultimate strength behaviours obtained were used as data for the development of closed form shape empirical formulation. Recently, Kim et al. [1] proposed for advanced empirical formulation for T-bar stiffened panel and the applicability of the proposed formulation to flat-bar stiffened panel will be confirmed by this study. The accuracy of the empirical formulation obtained for flat-bar stiffened panel has been validated by FE simulation results of statistical analysis (R2 = 0.9435). The outcome obtained will be useful for ship structural designers in predicting the ultimate strength performance of flat-bar type stiffened panel under longitudinal compression.

Inertial focusing conditions of fluorescent polystyrene spherical particles are studied at the pointwise level along their pathlines. This is accomplished by an algorithm that calculates a de-gree of spreading function of the particles' trajectories taking streaklines images as raw data. Different confinement ratios of the particles and flow rates are studied and the results are pre-sented in state diagrams showing the focusing degree of the particles in terms of their position within a curve of an asymmetric serpentine and the applied flow rate. In addition, together with numerical simulation results, we present empirical evidence that the preferred trajectories of inertially focused spheres are contained within Dean vortices' centerlines. We speculate about the existence of a new force, never postulated before, to explain this fact.

In this work, the recently proposed cracking elements method (CEM) is used for simulating the damaging processes of structures with initial imperfections. CEM is built in the framework of conventional FEM which is formally like a special type of finite element. The disconnected piecewise cracks are used for representing crack paths. Taking the advantages of CEM that both the initiations and propagations of cracks can be naturally captured, we numerically study the uni-axial compression tests of specimens with multiple joints and fissures, where the cracks may propagate from the tips, or from some other unexpected positions. Though uni-axial compression tests are considered, mainly tensile damage criteria are used in the numerical model. On one hand, the results demonstrate the robustness and effectiveness of the CEM while on the other hand, some drawbacks of the present model are demonstrated, showing the future work.

It is important to distinguish between natural earthquakes and those induced by CO2 injection at carbon capture and storage sites. For example, the 2004 Mw 6.8 Chuetsu earthquake occurred close to the Nagaoka CO2 storage site during gas injection, but we could not quantify whether the earthquake was due to CO2 injection or not. Here we simulated changes of pore pressure during CO2 injection at the Nagaoka site and compared them with estimated natural seasonal fluctuations of pore pressure due to rainfall and snowmelt as well as estimated pore pressure increases related to remote earthquakes. We clearly distinguished changes of pore pressure due to CO2 injection from those due to rainfall and snowmelt. The simulated local increase in pore pressure at seismogenic fault area was much less than the seasonal fluctuations related to precipitation and increases caused by remote earthquakes, and the lateral extent of pore pressure increase was insufficient to influence seismogenic faults. We also demonstrated that pore pressure changes due to distant earthquakes are capable of triggering slip on seismogenic faults. The approach we developed could be used to distinguish natural from injection-induced earthquakes and will be useful for that purpose at other CO2 sequestration sites.

Here, I introduce a concept called autonomous selection to refer to a source of selection that is part of the individuals upon which it acts. The concept is motivated by a set of phenomena with the following characteristics: Natural selection shaped a variant (e.g., gene, epigenetic mark, or combination thereof) to act in a manner that reduces the frequency of one or more heritable traits of the individual in which it is located if those traits are detrimental to individual or group fitness. Phenomena with these characteristics are peculiar to traditional evolutionary theory but have been identified rather frequently in recent decades. They are also relevant to adaptive evolution: By reducing the frequency of a trait detrimental to fitness, the variant accelerates the evolution of adaptations, which allows its holders to adapt better to constantly changing environments. The variant is shaped by (natural) selection, but also does (autonomous) selection. Several phenomena with these characteristics have been invoked by proponents of the extended evolutionary synthesis (EES). The concept of autonomous selection helps resolve some of the controversy surrounding the EES: EES proponents call attention to the incompleteness of contemporary theory, emphasizing individuals’ processes that influence which adaptations those individuals evolve. I argue for the special importance of individuals’ processes that do not just influence those individuals’ adaptations, but also accelerate the adaptive evolution of those individuals. All known phenomena that fit this description are examples of autonomous selection. Other phenomena raised by EES proponents do not meet this threshold.

Objective: To assess the functionality of the affected upper limb in children diagnosed with hemiplegia aged between 4 and 8 years after applying low-intensity modified constraint-induced movement therapy(mCIMT). Methods: Prospective case series study. A mCIMT protocol was applied for five weeks, with two hours of containment per day. The study variables were: quality of movement of the upper limb, spontaneous use, participation of the affected upper limb in activities of daily living, dynamic joint position, grasp-release action, grasp strength, supination and extension elbow movements. Four measurements were performed, using the QUEST scale, the SHUEE Evaluation, a hand dynamometer and a goniometer. Results: The sample was composed of 8 children with moderate manual ability. Statistically significant differences were detected in all the studied variables (p&lt;0.05). The greatest increase occurred in spontaneous use from assessment 1-4 (p = 0.01), reaching 88.87% active participation in bimanual tasks. The quality of movement of the upper limb obtained a significant value due to the increase in dissociated movements and grasp (p = 0.01). Conclusion: A low dose (50 hours) of mCIMT increased the functionality of children diagnosed with congenital hemiplegia between 4 and 8 years of age with moderate manual ability.

Embryoid bodies (EBs) are multicellular three-dimensional (3D) aggregates generated from induced pluripotent stem cells (iPSCs) in suspension and serve as useful biological sources for many downstream applications. Imaging of live EBs has been hampered mainly due to the inherent limitations of the imaging techniques applied to date. This study aimed to image human iPSC (hiPSC) derived EBs to obtain their 3D volume, determining size, morphology, and cell viability from day 7 to 14 using Light Sheet Fluorescence Microscopy (LSFM). Furthermore, chromosomal stability was assessed using Multicolor fluorescence in situ hybridization (M-FISH) from day 8 to 14. EB volume increased from day 7 to 13 which, decreased at day 14. From day 7 to 11, the EBs mainly appeared spherical and morphed into an ellipsoidal shape by day 13. All EBs showed varied external morphologies and larger cavities at day 14. The EB karyotype was diploid 46XY at day 8 and exhibited a low level of aneuploidy from day 10 to 14. This study shows that an increase in cell death affects the morphology and chromosomal stability in EBs derived from hiPSC. We demonstrate that the combination of LSFM and M-FISH helps characterize EBs that will assist future stem cell therapies.

The steady streaming (SS) phenomenon is gaining increased attention in the microfluidics community, because it can generate net mass flow from the zero-mean vibration. We developed numerical simulation and experimental measurement tools to analyze this vibration induced flow, which has been challenging due to its unsteady nature. Validity of these analysis methods is confirmed by comparing the three-dimensional (3D) flow field induced around a cylindrical micropillar under circular vibration. In the numerical modeling, we directly solved the flow in the Lagrangian frame so that the substrate with a micropillar becomes stationary, and the result was converted to the Eulerian frame to compare them with the experimental results. The present approach enables to avoid the introduction of moving boundary or small perturbation approximation. The flow field obtained by the micro particle image velocimetry (PIV) measurement supported the three-dimensionality observed in the numerical results, which could be important for controlling the mass transport and manipulating particulate objects in the microfluidic systems.

Drug induced liver injury (DILI) is the most common cause of acute liver failure and 5-10% of patients hospitalized for jaundice are diagnosed with DILI. For a diagnosis of DILI to be made, there should be exclusion of other etiologies of liver injury and the use of a precipitator drug, latency of symptoms, and resolution of liver injury once the offending drug is identified and discontinued. In our case report, we present a patient with idiosyncratic hepatocellular pattern DILI after two doses of ocrelizumab for treatment of multiple sclerosis. Ocrelizumab was given 16 and 27 days prior to the onset of icterus, jaundice, and fatigue, in a patient without the evidence of prior exposure to hepatitis B virus. At presentation labs revealed severe acute hepatocellular liver injury with R factor of 30.42, marked hyperbilirubinemia, and transient hypoalbuminemia. No evidence of latent or active hepatitis B infection was detected. Drug dechallenge led to return of liver chemistries to near-normal levels 31 days after the onset of her symptoms. This case indicates DILI diagnosis associated with the use of ocrelizumab, and warrants careful monitoring of liver functions in patients even in the absence of hepatitis B.

This article reports new measurements of laser-induced plasma hypersonic expansion measurements of diatomic molecular cyanide (CN). Focused, high-peak power 1064-nm Q-switched radiation of the order of 1 TW/cm² generates optical breakdown plasma in a cell containing a 1:1 molar gas mixture of N₂ and CO₂ at a fixed pressure of 1.1 × 10⁵ Pascal and in a 100 ml/min flow of the mixture. Line-of-sight (LOS) analysis of recorded molecular spectra indicate the outgoing shockwave at expansion speeds well in excess of Mach number 5. Spectra of atomic carbon confirm an increased electron density near the shock wave, and equally, molecular CN spectra reveal higher excitation temperature near the shockwave. The results are consistent with corresponding high-speed shadow graphs obtained by visualization with an effective shutter speed of five n anosecond. In addition, LOS analysis and application of integral inversion techniques allow inferences about the spatio-temporal distribution of the plasma.

Rubble stone masonry walls are widely diffused in most of the cultural and architectural heritage of historical cities. The mechanical response of such material is rather complicated to predict due to their composite nature. Vertical compression tests, diagonal compression tests, and shear-compression tests are usually adopted to experimentally investigate the mechanical properties of stone masonries. However, further tests are needed for the safety assessment of these ancient structures. Since the relation between normal and shear stresses plays a major role in the shear behavior of masonry joints, governing the failure mode, triplet test configuration was here investigated. First, the experimental tests carried out at the laboratory (LPMS) of the University of L'Aquila on stone masonry specimens were presented. Then, the triplet test was simulated by using the Total Strain Crack Model, which reflects all the ultimate states of quasi-brittle material such as cracking, crushing and shear failure. The goal of the numerical investigation was to evaluate the shear mechanical parameters of the masonry sample, including strength, dilatancy, normal and shear deformations. Furthermore, the effect of (i) confinement pressure and (ii) bond behavior at the sample-plates interfaces were investigated, showing that they can strongly influence the mechanical response of the walls.

Disruptive technologies (DT) have featured prominently in almost every human activity since the advent of computerization. The likely effects of DT on economic processes and human professions have and continue to generate fears and debates which spurred this investigation. To break away from the traditional approach the operational breakeven theory and the discriminant analysis techniques of Altman’s Z-score, and Enyi’s Relative Solvency Ratio were used to examine the relationship between firms’ market-induced-survival-ratio (MISR) and the disruptive technology gains index (DTGI) of seventy-three firms drawn from Nigeria and India. Descriptive and inferential statistics were used to analyze the data generated. The results showed that a sizeable number of firms has profited from the introduction of disruptive technologies with MISR and DTGI returning a 10% significant relationship while others are still struggling to measure up to the requirements of disruptive technologies in their chosen economic fields. The implication of this is that businesses must brace up and embrace digital transformation if they must stay afloat in this era of disruptive technologies. This study recommends a revolutionary approach to digital transformation in view of the fast pace of global integration while managers and business owners should adopt more pragmatic approach in appraising the operations and finances of a firm for effective results and timely responses to potential business challenges.

Multiagent technologies give a new way to study and control complex systems. Local interactions between agents often lead to group synchronization also known as clusterization, which usually is a more rapid process in comparison with relatively slow changes in external environment. Usually, the goal of system control is defined by the behaviour of a system on long time intervals. When these time intervals are much longer than the time of cluster formation, clusters may be considered as new variables in a ``slow'' time model. We call such variables ``mesoscopic'' to emphasize their scale laying between the level of the whole system (macroscopic scale) and the level of individual agents (microscopic scale). Thus, it allows us to reduce significantly the dimensionality of a system by omitting considerations of each separated agent, so that we may hope to reduce the required amount of control inputs. Thus, we are often able to consider a system as a collection of ``flowing'' (morphing) clusters emerged form behaviour of a huge amount of individual agents. In this paper, we contrast such approach to the one where a system is considered as a network of elementary agents. We develop a mathematical framework for analysis of cluster flows in multiagent networks and use it to analyze the Kuramoto model as an attracting example of a complex networked system. In this model, a clusterization leads to sparse representation of dynamic trajectories in the whole quantized state space. With that in mind, compressive sensing allows to restore the trajectories in a high-dimensional discrete state space based on significantly lower amount of randomized integral mesoscopic observations. We propose a corresponding algorithm of quantized dynamic trajectory compression. It could allow us to efficiently transmit the state space data to a data center for further control synthesis. The theoretical results are illustrated for a simulated multiagent network with multiple clusters.

Mesoscale imperfections, such as pores and voids, can strongly modify the properties and the mechanical response of materials under extreme conditions. Tracking the material response and microstructure evolution during void collapse is crucial for understanding its performance. In particular, imperfections in ablator materials, such as voids, can limit the efficiency of the fusion reaction and ultimately hinder ignition. To characterize how voids influence the response of materials during dynamic loading and seed hydrodynamic instabilities, we have developed a tailored fabrication procedure for designer targets with voids at specific locations. Our procedure uses SU-8 as a proxy for ablators materials and hollow silica microspheres as proxy for voids and pores. By using photolithography to design the targets’ geometry, we demonstrate precise and highly reproducible placement of a single void within the sample, which is key for a detailed understanding of its behavior under shock compression. This fabrication technique will benefit high-repetition rate experiments at x-ray and laser facilities. Insight from shock compression experiments will provide benchmarks for the next generation of microphysics modelling.

This paper reports an experimental investigation on compression after low-velocity impact response for two lay-up configurations of symmetric CFRP laminated composite specimens obtained by reversing their angle-ply orientation, namely [0/-45/45/90]s versus [90/45/-45/0]s, the impact velocity of the projectile up to the BVID level being subsequently considered. To this aim, a modified Compression-After-Impact (CAI) test device is proposed that involves clamping the specimen's upper and lower edges between two adjustable wide and flat anti-buckling plates through a removable bolt-nut assembly. Such a solution relies on the fact that the specimen's active length is shortened, reducing the risk of global buckling. Besides, the bolts carry part of the load with minor localized bearing damage, provided that the metallic plates act as washers by supporting the bolt-bearing region laterally, thus avoiding crashing failures at the specimens’ loaded edges. With these settings, roughly the same percent decrease in the average values of maximum compression load (i.e., 22%) was recorded for both lay-up configurations impacted up to their BVID threshold, whereas in terms of compressive stiffness behavior, a reduction of 17 % was found for [0/-45/45/90]s specimens compared to 6 % obtained for [90/45/-45/0]s specimens.

The plant immunity system is more and more revisited and new elements and roles are attributed to participate in the response to biotic stress. New terminology is also applied trying to identify different players in the whole scenario of immunity: Phytocytokines are one of those elements that are gaining more attention due the characteristics of processing and perception, and showing they are part of a big family of compounds that can amplify the immune response. This review aims to highlight the last findings about the role of phytocytokines in the whole immune response on biotic stress, including basal and adaptive immunity, and to expose the complexity in their action in plant perception and signaling events.

Electrical properties of the thin films of poly(arylene ether ketone) copolymers (co-PAEKs) with the fraction of phthalide-containing units of 3, 5 and 50 mol% in the main chain were investigated by using radiation induced conductivity (RIC) measurements. Transient current signals and current-voltage (I-V) characteristics were obtained under exposing 20÷25 thick films of the co-PAEKs to monoenergetic electron pulses of the energy ranged from 3 to 50 keV in the electric field ranged from 5 to 40 V/μm. The Rose-Fowler-Vaisberg semi-empirical model based on a multiple trapping formalism was used for an analysis of the RIC data and the parameters of the highly dispersive charge carrier transport were evaluated. The analysis revealed that charge carriers moved in isolation from each other and the applied electric fields were below the threshold field triggering the switching effect (a reversible high-to-low resistivity transition) in the co-PAEK films. It was also found that the co-PAEK films due to the super-linear I-V characteristics are highly resistant to electrostatic discharges arising from the effects of ionizing radiation. This property is important for the development of protective coatings for electronic devices.

Model understanding is critical in many domains, particularly those involved in high-stakes decisions, i.e., medicine, criminal justice, and autonomous driving. Explainable AI (XAI) methods are essential for working with black-box models such as Convolutional Neural Networks. This paper evaluates the traffic sign classifier of Deep Neural Network (DNN) from the Programmable Systems for Intelligence in Automobiles (PRYSTINE) project for explainability. The results of explanations were further used for the CNN PRYSTINE classifier vague kernels` compression. After all, the precision of the classifier was evaluated in different pruning scenarios. The proposed classifier performance methodology was realised by creating the original traffic sign and traffic light classification and explanation code. First, the status of the kernels of the network was evaluated for explainability. For this task, the post-hoc, local, meaningful perturbation-based forward explainable method was integrated into the model to evaluate each kernel status of the network. This method enabled distinguishing high and low-impact kernels in the CNN. Second, the vague kernels of the classifier of the last layer before the fully connected layer were excluded by withdrawing them from the network. Third, the network's precision was evaluated in different kernel compression levels. It is shown that by using the XAI approach for network kernel compression, the pruning of 5% of kernels leads only to a 1% loss in traffic sign and traffic light classification precision. The proposed methodology is crucial where execution time and processing capacity prevail.

Axial compression tests were carried out on 6 square steel tube confined concrete short columns and 6 BFRP square pipe confined concrete axial compression tests. The concrete strength grades were C30, C40, and C50. The test results show that the failure modes of steel pipe and BFRP pipe are obviously different, and the BFRP pipe undergoes brittle failure. Compared with the short columns of concrete confined by BFRP pipes, the ultimate bearing capacity of axial compression is increased by -76.46%, -76.01%, and -73.06%, and the ultimate displacements are -79.20%, -80.78%, -71.71%.

In recent years, laser engraving has received widespread attention as a convenient, efficient, and programmable method, which has enabled the obtaining of high-quality porous graphene from various precursors. Laser engraving is often used to fabricate the dielectric layer with micro-structure for capacitive pressure sensors, however, the usual choice of electrodes remains poorly flexible metal electrodes, which greatly limits the overall flexibility of the sensors. In this work, we propose a flexible capacitive pressure sensor made entirely of thermoplastic polyurethane (TPU) and laser-induced graphene (LIG) derived from wood. The capacitive pressure sensor consisted of a flexible LIG/TPU electrode (LTE), a LIG/TPU electrode with micro hole array, and dielectric layer of TPU with micro-cone array molded from laser-engraved hole array on wood, which provided high sensitivity (0.11 kPa-1), ultra-wide pressure detection range (100Pa to 1.4MPa), fast response (~300 ms) and good stability (&gt;4000 cycles, at 0-35 kPa). We believe that our research makes a significant contribution to the literature because the easily available materials derived from wood and overall consistent flexibility meet the requirements of flexible electronic devices.

Viroids are known the smallest plant pathogens, and although their genome sequences do not encode proteins, they can cause disease in economically important crops. In order to control viroid diseases and mitigate their damage, genetic resources used for breeding of the viroid-resistant crop have been searched, but the practical resistant trait has not been found in almost all viroid-crop combinations, as well as the tolerant trait. Due to the difficulty in exploiting naturally occurring resistance or tolerance, various effective strategies have been devised to control viroid diseases using non-transforming or transforming techniques. Meanwhile, extensive findings related to viroid resistance and tolerance may lead to confer resistance or tolerance to viroid infection by combining with the recently emerged new technologies (e.g., spray-induced gene silencing and genome-editing technologies), which are believed to be more environmentally viable and acceptable to the general public than previously reported approaches. In particular, some genome-modified crops produced by the latter technology are already on the market. In this review, we comprehensively summarize the current status about investigation of naturally occurring genetic traits for viroid resistance and tolerance, accumulating knowledge about host factors involved in viroid pathogenicity, and various basic technologies developed to try to possible viroid disease control strategies. Furthermore, we discuss prospects and challenges for the achievement of more effective, practical, and sustainable disease control of viroid.

The theory of electron spin has been proposed for a century, but the study of quantum effects in biological molecules is still in its infancy. Chirality-induced spin selectivity (CISS) is a very modern theory that can explain many biochemical phenomena. In this paper, we propose a new theoretical model based on CISS theory and quantum chemistry theory, which can well explain the theoretical explanation of the chiral selectivity of chiral proteins. Moreover, this theory can predict the spin state of corresponding chiral molecules. Taking L-DOPA and AADC enzyme as examples, this theoretical model solves the theoretical explanation of AADC enzyme's chiral catalysis selectivity problem and successfully predicts the spin state of L-DOPA and D-DOPA's valence electrons.

Axial compression tests were carried out on 6 square steel tube confined concrete short columns and 6 BFRP square pipe confined concrete axial compression tests. The concrete strength grades were C30, C40, and C50. The test results show that the failure modes of steel pipe and BFRP pipe are obviously different, and the BFRP pipe undergoes brittle failure. Compared with the short columns of concrete confined by BFRP pipes, the ultimate bearing capacity of axial compression is increased by -76.46%, -76.01%, and -73.06%, and the ultimate displacements are -79.20%, -80.78%, -71.71%.

The tri-trophic interactions between plants, insects, and insect predators and parasitoids are often mediated by chemical cues. The attraction to Herbivore-Infested Plant Volatiles (HIPVs) has been well documented for arthropod predators and parasitoids, and more recently for insectivorous birds. The attraction to plant volatiles induced by the exogenous application of methyl jasmonate (MeJA), a phytohormone typically produced in response to an attack of chewing herbivores, have provided controversial results, both in arthropod and avian predators. In this study, we aimed to examine whether potential differences in the composition of bouquets of volatiles produced by Herbivore-infested and MeJA-treated Pyrenean oak trees (Quercus pyrenaica) were related to differential avian attraction, as results from a previous study suggested. Results showed that the overall emission of volatiles produced by MeJA-treated and Herbivore-infested trees did not differ, and were higher than emissions of Control trees, although MeJA treatment showed more significant reaction and released several specific compounds in contrast to Herbivore-induced trees. These slight differences in the volatile composition may explain why avian predators were not so attracted to MeJA-treated trees as observed in a previous study in this plant-herbivore system. Unfortunately, the lack of avian visits to the experimental trees in the current study does not allow us to confirm this result and points out the need to perform more robust predator studies.

The development of gamma rays mutant rice lines would be a solution for introducing variability in already farmer using varieties. In vitro gamma (60Co) mutagenesis reduces chimeras and allows a faster selection of desired traits but requires laboratory process optimization. The objective of the present work was the in vitro establishment of a recalcitrant rice embryogenic calli, the determination of its sensitivity to gamma radiation (Co-60), sequencing MATK and Rubisco for identification purposes, as well as generation optimization. The radiosensitivity of embryogenic calli resulted in an LD50 of 110Gy, while the 20% lethal dose was 64Gy. All sequenced genes matched perfectly with already reported MATK and Rubisco O. sativa genes with a clear SNP that identifies the local variety related to the southeast Asia Region. Callus induction improves with an MS with 2mg/L 2,4D, and the regeneration was achieved with an MS medium with 3mg/L BAP and 0,5mg/L NAA. The optimized radiation condition was 60Gy with an 83% regeneration in a semisolid medium, allowing a balance between mutation and regeneration. When increased to 80Gy, the regeneration rate falls to 29%. An immersion system (RITA®) of either 60 or 120 seconds every 8hours allowed a systematic and homogeneous total regeneration of the recalcitrant line, in contrast with the semisolid medium that resulted in positive but irregular regeneration. Other well-known recalcitrant cultivars, CR1821, CR1113 also had an improving regeneration in the immersion system, demonstrating its potential use for recalcitrant materials. To our knowledge, this is the first report on using an immersion system to allow regeneration of gamma-ray mutants from recalcitrant rice materials.

The polygenic and multifactorial nature of many psychiatric disorders has hampered the personalized medicine approach implementation in clinical practice. However, induced pluripotent stem cell (iPSC) technology has emerged as an innovative tool for patient-specific disease modeling to expand the pathophysiology knowledge and treatment perspectives in the last decade. Current technologies enable adult human somatic cell reprogramming into induced pluripotent stem cells (iPSCs) to generate neural cells and direct neural cell conversion to model organisms that exhibit phenotypes close to human diseases, thereby effectively representing relevant aspects of neuropsychiatric disorders. iPSCs reflect patient pathophysiology and pharmacological responsiveness, particularly when cultured under conditions that recapitulate spatial tissue organization in brain organoids. Recently, the application of iPSCs has been frequently associated with gene editing that targets the disease-causing gene to deepen the illness pathophysiology and conduct drug screening. Moreover, gene editing has provided a unique opportunity to repair the putative causative genetic lesions in patient-derived cells. Here, we review the use of iPSC technology to model and potentially treat neuropsychiatric disorders by illustrating the key studies on a series of mental disorders, including schizophrenia, major depression disorder, bipolar disorder, and autism spectrum disorder. The future perspective will involve the development of organ-on-a-chip platforms that control the microenvironmental conditions to reflect individual pathophysiological by adjusting physiochemical parameters according to personal health data. This strategy could open new ways to build a disease model that considers individual variability and tailors personalized treatments.

Genetic sensorineural hearing loss and Meniere disease have been associated with rare variations in the coding and non-coding region of the human genome. Most of these variants are classified as likely pathogenic or variants of unknown significance and require functional validation in cellular or animal models. Given the difficulties to obtain human samples and the raising concerns about animal experimentation, human induced pluripotent stem cells emerge as cellular models to investigate the interaction of genetic and environmental factors in the pathogenesis of inner ear disorders. The generation of human sensory epithelia and neuron-like cells carrying the variants of interest may facilitate a better understanding of their role during differentiation. These cellular models will allow us to explore new strategies for restoring hearing and vestibular sensory epithelia as well as neurons. This review summarizes the use of human induced pluripotent stem cells in sensorineural hearing loss and Meniere disease and proposes some strategies for its application in clinical practice.

Here we investigated the acute effects of an exhaustive intermittent exercise session on immunological parameters of the elderly and the subsequent incidence of upper respiratory tract infections and compare with the moderate-intensity. To do so, ixty-three old subjects were divided into three groups HIIT (n=21) submitted at one High-intensity interval training, SCG (n=21) kept in a sedentary state, and MICT (n=21) submitted at moderate intensity walking. Blood were collected at 5 time points, before, immediately after, 2h, 24h, and 48h after the intervention. In result the IL-6 and TNF-α were overexpressed immediately after the IL-10 stood overexpressed and correlated with IL-17, denoting an inflammatory process, and evidencing an immunologic competence without enhancement of the prevalence of upper respiratory infection tract (URTIs). So a modulation in the balance of Th1/Th2/Th17 cytokines and leukocytes, these modifications did not cause the effect characterized as an immunological window. Perhaps, the typical inflammation process, with IL-10 and IL-17 participation could also produce benefits to combat infections, a pertinent discussion during a post-pandemic time; we consider it a safe exercise program for older adults.

Fixed offshore wind turbines continue to be developed for high latitude areas where not only wind and wave loads need to be considered, but also moving sea ice. Current rules and regulations for the design of fixed offshore structures in ice-covered waters do not adequately consider effects of ice loading and its stochastic nature on fatigue life of the structure. Ice crushing on such structures results in ice-induced vibrations, which can be represented by loading the structure using a variable-amplitude loading (VAL) sequence. Typical offshore load spectra are developed for wave and wind loading. Thus, a combined VAL spectrum is developed for wind, wave, and ice action. To this goal, numerical models are used to simulate the dynamic ice-, wind-, and wave-structure interaction. The stress time-history at an exemplarily selected critical point in an offshore wind energy monopile support structure is extracted from the model and translated into a VAL sequence, which can then be used as a loading sequence for the fatigue assessment or fatigue testing of welded joints of offshore wind turbine support structures. This study presents the approach to determine combined load spectra and standardized time series for wind, wave, and ice action.

Mandibular advancement devices (MAD) are an effective alternative treatment to CPAP. However, different maneuvers have been performed during the performance of drug sleep-induced endoscopy (DISE) to mimic the effect of MAD. Using the Selector Avance Mandibular (SAM) device, we aimed to identify MAD candidates during DISE using a titratable, reproducible, and measurable maneuver. This DISE-SAM protocol may help to find the relationship between the severity of the respiratory disorder and the degree of response, and to determine the advancement required to improve the collapsibility of the upper airway. Explorations were performed in 161 patients (132 males; 29 females) with a mean age of 46.81 (SD = 11.42) years, a BMI of 27.90 (SD = 4.19) kg/m2 and a mean AHI of 26.51 (SD = 21.23). Results showed no relationship between severity and MAD recommendation. Also, there was a weak positive relationship between the advancement required to obtain a response and the disease severity. Using the DISE-SAM protocol, the response and the range of mandibular protrusion were assessed, avoiding the inter-examiner bias of the jaw thrust maneuver. We suggest prescribing MAD as a single, alternative, or multiple treatment approaches following the SAM recommendations in a personalized design.

Thrombosis is the pathological clot formation under abnormal hemodynamic conditions, which can result in vascular obstruction, causing ischemic strokes and myocardial infarction. Thrombus growth under moderate to low shear (<1000 s^-1) relies on platelet activation and coagulation. Thrombosis at elevated high shear rates (>10,000 s-1) is predominantly driven by unactivated platelet binding and aggregating mediated by von Willebrand factor (VWF), while platelet activation and coagulation are secondary in supporting and reinforcing the thrombus. Given the molecular and cellular level information it can access, multiscale computational modelling informed by biology can provide new pathphysiological mechanisms that are otherwise not accessible experimentally, holding promise for novel first-principle-based therapeutics. In this review, we summarize the key aspects of platelet biorheology and mechanobiology, focusing on the molecular and cellular scale events and how they build up to thrombosis through platelet adhesion and aggregation in the presence or absence of platelet activation. In particular, we highlight recent advancements in multiscale modeling of platelet biorheology and mechanobiology and how they can lead to better prediction and quantification of thrombus formation, exemplifying the exciting paradigm of digital medicine.

The microstructure of oil pipeline steels is polycrystalline due to the presence of a complex grain boundary (GB) network in them. The performance of them when exposed to stresses in corrosive environments is largely dictated by the interplay between the hydrogen (H) diffusion, the dislocation slip, and their interactions with the GBs. However, the slip-GB interaction in the presence of H and the subsequent cracking along the GBs remains not fully understood up to date. It is challenging to simultaneously resolve the collective dislocation motions away from the GBs together with the H diffusion near the atomically structured GBs using single-scale techniques. To address this challenge, taking bcc iron as a model material, here we present a a concurrent atomistic-continuum (CAC) computational analysis of the interaction between dislocation slip and a H-charged GB. With the large number of dislocations-mediated plastic flow away from the GB together with the atomistic structure evolution at the GB being simultaneously retained, several main findings from our simulations are: (i) the large number of dislocation-mediated pileup-induced internal stress nearby the H-charged GB can be as high as 3GPa; (ii) the more dislocations accumulated nearby the GB, the slower H diffusion ahead of the slip-GB intersection; (iii) H atoms diffuse fast behind the pileup tip, get trapped within the GB, and diffuse slow ahead of the pileup tip; (iv) the local stresses nearby the pileup tip exhibits a strong heterogeneity along the dislocation line direction. This differs from the common wisdom in many existing 2D theories/models. The buildup of such a high local stress heterogeneity leads to inhomogeneous H diffusion within the GB plane. The CAC simulation-predicted local H diffusivity, Dpileup−tip, and local stresses, σ, nearby the GB are then correlated with each other and consolidated into a mechanics model by considering the dislocation pileup as an Eshelby inclusion. These findings will provide researchers with opportunities to: (a) characterize the coupled dynamics between plasticity, H diffusion, and crack initiation underlying the hydrogen-induced cracking (HIC); (b) develop mechanism-based constitutive rules to be used in diffusion-plasticity coupling models for understanding the interplay between mechanical and mass transport in materials at the continuum level; and (c) connect the atomistic deformation physics of polycrystalline materials with their overall performance in aqueous environments, which is currently difficult to achieve in laboratory experiments.

The present overview of spin-dependent phenomena in nonmagnetic semiconductor microparticles (MPs) and nanoparticles (NPs) with interacting nuclear and electron spins is aimed at covering a gap between the basic properties of spin behavior in solid-state systems and a tremendous growth of the experimental results on biomedical applications of those particles. The first part of the review represents modern achievements of spin-dependent phenomena in the bulk semiconductors from the theory of optical spin orientation under indirect optical injection of carriers and spins in the bulk crystalline silicon (c-Si) – via numerous insightful findings in the realm of characterization and control through the spin polarization – to the design and verification of nuclear spin hyperpolarization in semiconductor MPs and NPs for magnetic resonance imaging (MRI) diagnostics. The second part of the review is focused on the electron spin-dependent phenomena in Si-based nanostructures, including the photosensitized generation of singlet oxygen in porous Si and design of Si NPs with unpaired electron spins as prospective contrast agents in MRI. The experimental results are analyzed by considering both the quantum mechanical approach and several phenomenological models for the spin behavior in semiconductor/molecular systems. Advancements and perspectives of the biomedical applications of spin-dependent properties of Si NPs for diagnostics and therapy of cancer are discussed.

The aim of the present work is to explore a different non-traditional approach to higher dimensional spacetime which differs from the usual approaches such as large extra space dimensions, warped extra space dimensions and multiple extra time dimensions. This approach will be referred to as "Dynamic" higher dimensional spacetime. By this term will be introduced a new kind of higher dimensional spacetime (more than the usual 3+1 dimensions), which behaves dynamically in the sense that time is not a fixed dimension but is the extra plus one dimension to the spatial dimensions of the phenomenon we are studying. For a higher dimensional phenomenon, the lower dimensional time will behave as space and the new time will be a plus one dimension, meaning if we study a 3-dimensional phenomenon then time is the usual 4th dimension but if we are studying a 4-dimensional phenomenon then its time will be an extra 5th dimension and for this phenomenon the 4th dimension will behave as space. All spatial dimensions are indistinguishable from each other and behave in the exact same way, which means that the important parameter is not the dimension we are studying (for example the 4th or the 5th) but the number of dimensions in which a phenomenon can interact and how higher dimensional phenomena interact with lower ones. This non-traditional approach to higher dimensional spacetime may appear confusing at first but will become clearer in the rest of the paper. For this reason, we will first associate the time dimension with propagation relative to space dimensions and change orthogonal to them in order to give the reader a better intuition. Following that, we will describe how higher - dimensional phenomena would appear to us, the 3 - dimensional observer and try to set some guidelines on how we should mathematically model higher - dimensional phenomena in order for us to make accurate predictions of their behaviour. Then we will express the general framework of a "Dynamic" higher - dimensional spacetime and turn our gaze to 4+1 – dimensional phenomena. We will explore how a mass term arises for 4 – dimensional waves by generalizing the frequency – speed – wavelength relation of 3D waves and give a basic description on a possible way to describe a 4+1 – dimensional disturbance in a scalar Energy Field in order to make accurate predictions on our 3+1 dimensional plane. In this framework we will derive the Klein – Gordon equation by generalizing the wave equation and ignoring all lower than 4+1 - dimensional disturbances and compere our mass term findings with the Klein – Gordon equation mass term and with results from gravity – induced quantum interference experiments. Lastly, we will describe how a "Dynamic" 5 - dimensional spacetime would appear in a 3D observer and examine whether our findings are compatible with quantum mechanics and the special theory of relativity.

Alloys based on TiNi are widely used in various fields of technology and medicine. In the present work, we report on preparation of TiNi-alloy based wire with the shape memory effect, which was used for compression clips for surgery. Composition and structure of the wire, and its martensitic and physical-chemical properties were studied using SEM, TEM, optic microscopy, profilometry, mechanical tests, etc. The TiNi alloy was found to consist of B2 and B19' and secondary-phase particles of Ti2Ni, TiNi3 and Ti3Ni4. Its matrix was slightly enriched in Ni (50.3 at. % of Ni). Homogeneous grain structure was revealed (an average grain size of 19±0.3 μm) with equal quantities of grain boundaries of special and general types. Surface oxide layer provide improved biocompatibility and promote adhesion of protein molecules. Overall, the obtained TiNi wire was concluded to exhibit martensitic, physical and mechanical properties suitable for its use as an implant material. The wire was then used for manufacturing compression clips with the shape memory effect and applied in surgery. The medical experiment that involved 46 children demonstrated that the use of such clips in children with double-barreled enterostomies permitted to improve the results of surgical treatment.

Movement disorders can be associated with various drugs and systemic diseases, posing diagnostic challenges for clinicians. This review explores the spectrum of movement disorders associated with pharmacological agents and medical conditions. Drug-induced movement disorders encompass a broad range of conditions resulting from exposure to medications that affect several neurotransmitters. Neuroleptic medications can lead to tardive dyskinesia, characterized by involuntary, repetitive movements. Antipsychotics and antiemetics, including metoclopramide, may induce acute dystonic reactions. Other drugs, such as dopamine receptor-blocking agents, can contribute to drug-induced parkinsonism. Beyond medications, movement disorders can also arise secondary to systemic diseases. Metabolic disorders like Wilson's disease, characterized by copper accumulation, may manifest as chorea or dystonia. Inflammatory conditions such as rheumatoid arthritis and systemic lupus erythematosus can result in secondary movement disorders due to autoimmune-mediated processes affecting the central nervous system. Movement disorders linked to drugs or systemic diseases often necessitate a thorough clinical evaluation, including detailed medication histories and comprehensive systemic assessments. Neuroimaging, laboratory investigations, and, in some cases, cerebrospinal fluid analyses and electrodiagnostic studies help in establishing accurate diagnoses. Management involves addressing the underlying cause, modifying medications, and employing symptomatic treatments.

The inherent trace quantity of primary fatty acid amides found in biological systems presents challenges for analytical analysis and quantitation, requiring a highly sensitive detection system. The use of microfluidics provides a green sample preparation and analysis technique through small-volume fluidic flow through micron-sized channels embedded in a PDMS device. Microfluidics provides the potential of having a micro total analysis system where chromatographic separation, fluorescent tagging reactions, and detection are accomplished with no added sample handling. This study describes the development and optimization of a microfluidic-laser indued fluorescence (LIF) analysis and detection system that can be used for the detection of ultra-trace levels of fluorescently tagged primary fatty acid amines. A PDMS microfluidic device was designed and fabricated to incorporate droplet-based flow. Droplet microfluidics have enabled on-chip fluorescent tagging reactions to be performed quickly and efficiently, with no additional sample handling. An optimized LIF optical detection system provided fluorescently tagged primary fatty acid amine detection sub-fmol (436 amol) LODs. The use of this LIF detection provides unparalleled sensitivity, with detection limits several orders of magnitude lower than currently employed LC-MS techniques and might be easily adapted for use as a complementary quantification platform for parallel MS-based -omics studies.

Laser Direct Writing (LDW), also known as 3D multi-photon laser lithography of resins, is a promising technique for fabricating complex free-form elements, including micro-optical functional components. Regular organic or hybrid (organic-inorganic) resins are often used, with latter exhibiting better optical characteristics, as well as having the option to be heat-treated into inorganic glass-like structures, particularly useful for resilient micro-optics. While this work is a continuation of SZ2080™ calcination development , the Laser-Induced Damage Threshold (LIDT) of such sol-gel-derived glass micro-structures, particularly those that undergo heat treatment, has not been well-characterized. In this pilot study, we investigated the LIDT using the Series-on-One (S-on-1) protocol of functional micro-lenses produced via LDW and subsequently calcinated. Our results demonstrate that the LIDT can be significantly increased, even multiple times, by this approach, thus enhancing the resilience and usefulness of these free-form micro-optics. This work represents the first investigation in terms of LIDT into the impact of calcination on LDW produced sol-gel-derived glass micro-structures, and provides important insights for the development of robust micro-optical devices.