The fundamental challenge for the structural design of complicated shapes and lightweight structures such as Tensile Membrane Structures (TMS) is a reliable estimation of lateral loading such as wind load. Wind pressure coefficients can’t be correctly calculated by standards for a large range of intricate forms of structures. Computational Fluid Dynamics (CFD), a strong computational technique for evaluating wind pressure distribution on complicated geometry, can be used to determine wind-related parameters. The average wind related-distributions for the tensile membrane surface are validated with a few contributions from prior studies, which are important to validate with benchmarks in experimental wind tunnel experiments. For the double-curved surface, the results show good agreement between experimental tests and CFD simulations. In this study, CFD simulation was used to calculate the mean surface pressure coefficient (Cp) for generic shapes and tensile membrane forms using the steady Reynolds-Averaged Navier-Stokes (RANS) technique. Wind force coefficients and the effect of wind directions are also explored across a wide range of classical and tensile forms. The purpose of the current research is to look at the effect of wind assault angle on the Cp distribution for tensile membrane structures and general shapes.

Satellite measurements are one of the main sources of data on the state of the marine environment. To obtain information about the sea brightness coefficient , it is needed to correctly carry out atmospheric correction. In the presence of dust aerosol over the Black Sea, physically incorrect values of the spectral brightness coefficient often occur, and specifically negative values in the IR region of the spectrum. The main objective of the study is to evaluate the influence of dust aerosol on the spectral dependence of sea brightness, based on analytical calculations from the transfer theory using the principle of plane-parallel layers and results of validation of AERONET-OC field and remote sensing data. The work analyzes spectral dependence of the first error eigenvector of the standard atmospheric correction in the presence of dust aerosol. As result it is given that with an absorbing aerosol, the atmospheric correction error is described by the spectral course of molecular scattering, i.e. close to

Lipid mesophases are being intensively studied as potential candidates for drug-delivery purposes. Extensive experimental characterization has unveiled a wide palette of release features depending on the nature of the host lipids and of the guest molecule, as well as on the environmental conditions. However, only few simulation works have addressed the matter, which hampers a solid rationalization of the richness of outcomes observed in experiments. Particularly, to date there are no theoretical works addressing the impact of hydropathy on the transport of a molecule within lipid mesophases, despite the significant fraction of hydrophobic molecules among currently-available drugs. Similarly, the high heterogeneity of water mobility in the nanoscopic channels within lipid mesophases has also been neglected. To fill this gap, we introduce here a minimal model to account for these features in a lamellar geometry, and systematically study the role played by hydropathy and water-mobility heterogeneity by Brownian-dynamics simulations. We unveil a fine interplay between the presence of free-energy barriers, the affinity of the drug for the lipids, and the reduced mobility of water in determining the net molecular transport. More in general, our work is an instance of how multiscale simulations can be fruitfully employed to assist experiments in release systems based on lipid mesophases.

Light travels in a moving medium through densities that differ from the density of that medium at rest. This study derives a formula for light velocity through a moving medium for any direction of light propagation in that medium that, applied to the Fizeau experiment, gives a fringe shift of 0.23541. The Fresnel drag coefficient applied to the Fizeau experiment offers a fringe shift of 0.20466. The mean of the fringe shift observations in the Fizeau experiment of 0.23016 confirms both expectations.

The unique properties and morphology of liquid marbles (LMs) make them potentially useful for various applications. Non-edible hydrophobic organic polymer particles are widely used to prepare LMs. It is necessary to increase the variety of LM particles to extend their use into food and pharmaceuticals. Herein, we focus on hydrophobically modified gelatin (HMG) as a base material for the particles. The surface tension of HMG decreased as the length of alkyl chains incorporated into the gelatin and the degree of substitution (DS) of the alkyl chains increased. HMG with a surface tension of less than 37.5 mN/m (determined using equations based on the Young-Dupré equation and Kaelble-Uy theory) successfully formed LMs of water. The minimum surface tension of a liquid in which it was possible to form LMs using HMG particles was approximately 53 mN/m. We also showed that the liquid-over-solid spreading coefficient S_(L/S) is a potential new factor for predicting if particles can form LMs. The HMG particles and the new system for predicting LM formation could expand the use of LMs in food and pharmaceuticals.

Competition between cotton, winter, and summer crops is the greatest obstacle for plant breeders in Egypt. Breeders are thus seeking early maturing, high-yielding cultivars that are suited for planting following winter crops. This study was conducted during the 2016 and 2018 growing seasons at the Sakha agriculture research station, Egypt's agricultural research facility. This research used breeding material from the F2, F3, and F4 generations that resulted from crossing Giza 94 and Uzbekistan. During the 2016 growing season, the F2 population was cultivated, and the top 5% of the F2 population (75 plants) were chosen based on the selection criteria. In the summer of 2017, the F3 families were cultivated, and 5% of the superior F3 families were chosen to become the F4 fam-ilies, which were planted in the summer of 2018 at the single plant and bulk studies in a randomised full block design with three replications. The average performance of the characteristics boll weight, seed cotton yield, lint percentage, and lint index increased as generations passed from F2 to F4. In the meanwhile, the characteristic value of the first flower to open decreased, showing the accu-mulation of advantageous alleles. For all examined characteristics, the phenotypic coefficient of variance was greater than the genotypic coefficient of variation. In addition, the data demonstrated that heritability in a broad sense was greater in F4 populations than in F3 and F2 populations. With a few exceptions, the phenotypic and genotypic associations for all investigated characteristics were positive and very significant. According to the data, initial opening flowering and boll weight had a substantial impact on seed cotton output per feddan. In general, five superior families No. 9, 13, 18, 19, and 20 were chosen from the F4 population, which were more significant for yield and yield component than the commercial variety, and these genotypes may be promising for the breeding programme to develop new genotypes with superior yield.

Usually in quantum optics, the theory of large- and small-scale waveguide beam splitters is the same. In this paper it is shown that the theory of the nanoscale waveguide beamsplitter has a significant difference from a similar device, but of a larger scale. It is shown that the previously known theory of the waveguide beam splitter is a particular case of the theory presented here. The wave function at the output ports of the nanoscale beam splitter is analyzed. The results obtained are sensitive to the size of the beam splitter, the coupling parameter of the two waveguides, and the degree of nonmonochromaticity of the photons entering the first and second ports of the beam splitter. The results are important for quantum technologies using a nanosized beam splitter.

Using the 2011-2020 digital inclusive finance data released by Peking University and the index system constructed by the Blue Book of China Rural Revitalization and Development Index (2018), this paper analyzes the dynamic evolution of the digital inclusive finance and the rural revitaliza-tion from time and space dimensions with the help of kernel density estimation, Markov chain and Moran index. Using The Gini coefficient decomposition method to analyze the source of differ-ences in digital inclusive finance, and then using the spatial autoregressive (SAR) model and ge-ographically weighted regression (GWR) model to study the boosting effect of digital inclusive finance on rural revitalization from the perspective of spatial aggregation and spatial differentia-tion, respectively. The results show that: (1) The growth rate of China's digital inclusive finance slows down year by year, and the inter-provincial differences increase year by year and show gradient characteristics, indicating that there may be a trend of multipolar differentiation. The overall level of Rural Revitalization shows an increasing trend, and the gap between provinces is still apparent. (2) The evolution of digital inclusive finance and rural revitalization is a slow ad-justment process, and there has been no cross-level jump in the past ten years. In digital inclusive finance, the liquidity from the highest and lowest levels to the medium level is high. However, the liquidity in the states of rural revitalization development level is not high. (3) Rural revitalization has a positive spatial spillover effect. The level of rural revitalization in the western area is signif-icantly lower than in the eastern area. At the same time, there is no significant difference between the east and central areas. The depth of the use of digital inclusive finance has a significant positive impact on the revitalization and development of rural areas, indicating that the further promotion of digital inclusive finance business in rural areas can substantially boost the revitalization of rural areas. (4) The boosting effect of digital inclusive finance on rural revitalization shows prominent spatial differentiation characteristics. The depth of use and the degree of digitization generally show a positive impact. The central and eastern coastal cities have the highest impact, decreasing toward the southwest and northeast. The areas with the lowest usage depth impact are clustered in the northeast, and the areas with the lowest digitization impact are clustered in the southwest.

The object of this work is to determine the correlation on the Nusselt number on the individual rows of a four-row tubular finned heat exchanger with continuous fins with a staggered tube arrangement using CFD modelling. Correlations for calculating Darcy-Weisbach friction factors on individual tube rows were also determined. Relationships for the Nusselt number and friction factor derived for the entire exchanger based on CFD modelling were compared with those available in the literature determined using experimental data. The maximum relative differences between the Nusselt number for a four-row exchanger determined experimentally and by CFD modelling are in the range from 22% for a Reynolds number based on a tube's outside diameter of 1,000 to 30% for a Reynolds number of 13,000. The maximum relative differences between the friction factor for a four-row exchanger determined experimentally and by CFD modelling are in the range of 50% for a Reynolds number based on a tube outer diameter of 1,000 to 10% for a Reynolds number of 13,000. The CFD modeling performed shows that in the range of Reynolds numbers based on hydraulic diameters from 150 to 1,400, the Nusselt number for the first row in a four-row finned heat exchanger is about 22% to 15% higher than the average Nusselt number for the entire exchanger. In the range of Reynolds number changes based on hydraulic diameter from 2,800 to 6,000, the Nusselt numbers on the first and second rows of tubes are close to each other. Correlations on Nusselt numbers and friction factors derived for individual tube rows can be used in the design of plate-fin and tube heat exchangers used in equipment such as air-source heat pumps, automotive radiators, air-conditioning systems and in air hot-liquid coolers. In particular, the correlations can be used to select the optimum number of tube rows in the exchanger.

Open-cell metallic foams used as catalyst supports exhibit excellent transport properties. In this work, a unique application of metallic foam, as pelletized catalyst in a packed bed reactor, is examined. By using a wall-segment Computational Fluid Dynamics (CFD) setup, parametric analyses are carried out to investigate the influence of foam morphologies (cell size ϕ=0.45-3 mm and porosity ε=0.55-0.95) and intrinsic conductivity on flow and heat transport characteristics in a slender packed bed (N=Ddp=6.78) made of cylindrical metallic foam pellets. The transport processes have been modeled using an extended version of conventional particle-resolved CFD, i.e., flow and energy in inter-particle spaces are fully resolved, whereas porous-media model is used for the effective transport processes inside highly-porous foam pellets. Simulation inputs include the processing parameters relevant to Steam Methane Reforming (SMR), analyzed for low (Rep~100) and high (Rep~5000) flow regimes. The effect of foam morphologies on packed beds has shown that the desired requirements contradict each other, i.e., increase in cell size and porosity favor the reduction in pressure drop, however lowering the heat transfer efficiency. A design study is also conducted to find the optimum foam morphology of a cylindrical foam pellet at higher Rep~5000, which yields ϕ = 0.45, ε = 0.8. Suitable correlations to predict the friction factor and the overall heat transfer coefficient in a foam packed bed have been presented, which considers the effect of different foam morphologies over a range of particle Reynolds number, 100≤Rep≤5000.

The health of the landing gear retraction and extension hydraulic system may be assessed using fuzzy comprehensive evaluation (FCE), however the traditional FCE method depends solely on human assessment by specialists, which is excessively subjective. To address the issue of excessive human subjective variables in the assessment, an improved FCE model based on enhanced risk coefficient is provided, which includes four consideration indexes: failure probability, failure severity, failure detection difficulty, and failure repair difficulty. To reduce subjective human judgment errors entirely due to expert experience, the improved FCE takes into account the likelihood of failure using a statistical method, the severity of failure using a fault simulation analysis based on the LMS Imagine.Lab AMESim simulation platform, and the difficulty of fault detection and repair using the aircraft manufacturer's professional maintenance information. As part of the evaluation model, the range of health assessment values and accompanying treatment methods are included, making it easier to implement on a daily basis in aircraft maintenance. As a final step, the simulation is evaluated and the simulated faults are calculated.

Trade of agricultural products has gained importance with the development of global trade. Cherries has a crucial place in Turkish agricultural exports. Fresh cherries are in the scope of this study. The aim of this study is to examine Turkey’s position and competitiveness in cherry trade. Trade Intensity Analysis Method which represents the course of trade flow among countries is used in the study. The study indicates that European countries which are Turkey’s tradition trade partner has a biggest trade share with Turkey and that share did not much change in years. By the way, Asia market especially China, became a game changer in cherry trade and Turkey should prepare itself for this situation.

This review summarises the main numerical models of fuel droplet heating and evaporation (DHE) in combustion engines across the different scales by accessing the nano/micro, meso and macroscopic fluid elements. The phenomena of multi-physics, multi-scale and multi-phase fluid flow and heat transfer are fully investigated when the fuel droplet (dodecane) is heating and evaporated into a background gas (nitrogen) crossing the liquid-vapour (LV) interface, kinetic region (i.e., Knudsen layer) and the bulk regions of liquid and gas in terms of molecular dynamics (MD) simulations, kinetic theory modelling (i.e., direct numerical solutions of Boltzmann equations) and convectional fluid dynamics approach, respectively. The evaporation coefficient of fuel evaporating molecules and their velocity distributions at the LV interface derived from MD simulations formulate a new kinetic boundary condition (KBC). Moreover, a novel kinetic model considering the inelastic collision between fuel molecules alongside the new KBC enables us to describe the non-equilibrium gas dynamics of fuel vapour and gas mixture in Knudsen layer (KL). Heat and mass flux analysis of the fuel droplet under combustion engine conditions can be accurately assessed by implementing the inelastic collision between fuel molecules in KL and a temperature-dependent evaporation coefficient at the LV interface into DHE. The surface temperature of fuel droplet and its evaporation time, which play a significant role in resolving the ignition delay and hence the combustion phasing in engines, can also be well estimated. The multi-scale modelling of fuel DHE will make significantly potential input into the cleaner engine targeting the low-carbon emissions and enhance the capability of the existing computational fluid dynamics (CFD) solvers.

Nowadays, energy saving is considered a key issue worldwide, as it brings a variety of benefits: reducing greenhouse gas emissions, reducing demand for energy imports, and lowering costs on a household and economy-wide level. Researchers and building designers are looking to optimize building efficiency by means of new energy technologies. Changes in existing buildings can also be made to reduce energy consumption and costs. These may include the usage of new heat transfer fluids based on nanofluids. In this work, an extended experimental campaign (from February 2020 to March 2021) has been carried out on an educational building in the Campus of University of Salento, Lecce – Italy, in order to evaluate the increase in performance of the HVAC system, due to the usage of a nanofluid. The results show that, under optimal operating conditions, plant performance improves more than 10%, with average daily peaks of about 15%.

Using an original method for measuring weak radiothermal electromagnetic signals, experimental data were obtained on the analysis of dispersions of noise attractors of the radiobrightness temperature of aqueous solutions of NaCl, Al (NO₃)₃ at dilutions C1 (1:100) – C12 (12:100). The values of dispersions of noise attractors significantly differ from those for the control experiment with water. On the basis of the changed values of the noise attractors of the radiobrightness temperature, the values of the absorption coefficients of the solutions are calculated. The difference between the values of the solutions absorption coefficients and those for water is shown with a successive increase in their values with an increase in the degree of dilution. The difference between the values of the absorption coefficients of solutions of high dilutions and those for water is interpreted as a mechanism of cooperative interaction of ions with water molecules located outside the first hydration shell. A network of water molecules perturbed by ions contributes to the dielectric permittivity was obtained due to new properties at supramolecular interactions on the basis of dispersion interaction.

This article describes the methodology used to identify the mathematical model that describes the correlations between the input parameters of an experiment and the parameters being followed. As a technological process, the aerodynamic separation was chosen, respectively, the behavior of a solid particle within an ascending vertical airflow. The experimental data obtained were used to identify two parameters, the average linear velocity, and the angular velocity, and through the Table Curve 3D program was developed a mathematical model which describes the dependence between the input parameters (the shape and size of the solid particle and the velocity of the airflow) and the monitored parameters. In order to determine a single mathematical equation that describes as accurately as possible the correlation between the input variables and those obtained, a pyramid-type analysis was designed. The determination of the mathematical equation started from the number of equations generated by the Table Curve 3D program, then the equations with a correlation coefficient greater than 0.85 were chosen, and finally, the common equations were identified. Respecting the working methodology was identified one equation which has for the average linear velocity a correlation coefficient r2 between 0.88-0.99 and 0.86-0.99 for the angular velocity.

Default aerosol extinction coefficient profiles are commonly used instead of measured profiles in radiative transfer modelling, increasing the uncertainties in the simulations. The present study aims to determine the magnitude of these uncertainties and contribute towards the understanding of the complex interactions between aerosols and solar radiation. Default, artificial and measured profiles of the aerosol extinction coefficient are used to simulate the profiles of different radiometric quantities in the atmosphere for different surface, atmospheric, and aerosol properties and for four spectral bands: ultraviolet-B, ultraviolet-A, visible, and near infrared. Case studies are performed over different areas in Europe and North Africa. Analysis of the results shows that under cloudless-skies, changing the altitude of an artificial aerosol layer has minor impact on the levels of shortwave radiation at the top and the bottom of the atmosphere, even for high aerosol loads. Differences up to 30% were however detected for individual spectral bands. Using measured instead of default profiles for the simulations leads to more significant differences in the atmosphere, which become very large during dust episodes (10 – 60% for actinic flux at altitudes between 1 and 2 km, and up to 15 K/day for heating rates depending on site and solar elevation).

The aim of the studies was to test the hydraulic pressure losses along the length, local pressure losses, absolute and relative roughness values of the pipeline walls made of modern polymer material. The article presents the results of the experimental studies of hydraulic resistance of pipelines from modern polymer materials, the method of theoretical determination of resistance coefficients in the VALTEC ISO 21003 metal polymer pipeline, the classification and method of determining the values of local hydraulic resistance coefficients of T-Junctions are given, the dependence for determining the Darcy λ hydraulic friction coefficient associated with the value of the equivalent hydraulic roughness coefficient of the inner surface of pipes and the Reynolds number. The experimental data of the hydraulic coefficient of friction Darcy λ was compared with the known theoretical relationships of A.D. Altschul, Colbrooke for smooth pipes, Colbrooke and White, an alternative to the Colbrooke-White, Offengenden equation for low-shear pipes and pipes from polymer materials with Reynolds numbers Re>10^4. Dependence of hydraulic coefficient of friction on relative equivalent roughness of pipeline walls and Reynolds number, specific energy loss per one linear meter on total flow rate in system of hydraulically short pipeline is obtained. The empirical dependence of values of coefficients of local resistance ζ=f(Q2/Q3) from a ratio of the divided expenses of Q2/Q3 of the equal-pass T-Junction α=90 the pipeline to a branch up, on pass in the direct T-Junction and division of streams at various internal pipeline diameters of VALTEC.

Currently, the design and construction of embankments of roads, railroads and hydraulic structures are based on regulatory documents developed 25-30 years ago. For the construction of granite massifs it is necessary to use sandy soils, the distribution of which in the Arctic zone of Siberia in the areas of construction is not more than 1.5%. In this case, the range of transport of sand in the alluvial area is 35 kilometers, in the rest of the area - an average of 60 kilometers. Large volumes of soil massifs require large amounts of transportation units, fuel consumption and are accompanied by large emissions of hydrocarbons into the atmosphere. Over the past 15 years, the authors have developed designs and technologies that significantly reduce the energy consumption during the construction of soil embankments. Combined structures are cages made of geosynthetic materials filled with unsuitable melted and frozen overmoistened clay and peaty soils. This allowed the use of soils within the construction sites and thereby reduce the range of transportation from 0.2 to 2.0 kilometers. As an example, when reducing the range of transportation from 25 km to 1 km, the energy consumption is reduced by a factor of 21. The use of geosynthetics made it possible to set the initial parameters of the water-heat regime control process, which increased the life cycle of the embankment from 2 to 5 times in comparison with traditional soil massifs and reduced the consumption of energy for repair and maintenance of linear transport structures. This article gives a theoretical substantiation of water-heat regime management, based on which new designs and technologies have been proposed and tested in Siberia in 2008-2013. The results of the tests confirm the theoretical research. Thus, the use of combined constructions of geosynthetics and inapplicable soils not only reduces the distance of transportation, but also reduces the volume of earthworks. It reduces the consumption of energy by 1.5-2 times.

The effect of the communication channel size on the transport and subsequent detection of chemical messengers is investigated on millimetric and micrometric channels. The transport of the information carriers, being characterized by an advective and a diffusive contribution, was simulated by varying the flow velocity and the diffusion coefficient. Then, to evaluate the information quality, the Intersymbol Interference (ISI) between two consecutive signals at a specific release delay was estimated. This allowed us to verify that operating under micrometric channel conditions has a larger flow velocity range to obtain completely separated successive signals and smaller release delays can be used between signals. The theoretical results were confirmed by developing a prototype molecular communication platform operating under microfluidic conditions, which enables communication through fluorescent nanoparticles, namely Carbon Quantum Dots (CQDs).

The European Power Exchange has introduced day-ahead auctions and continuous trading spot markets to facilitate the insertion of renewable electricity. These markets are designed to balance excess or lack of power in short time periods, which leads to a large stochastic variability of the electricity prices. Furthermore, the different markets show different stochastic memory in their electricity price time series, which seem to be the cause for the large volatility. In particular, we show the antithetical temporal correlation in the intraday 15 minutes spot markets in comparison to the day-ahead hourly market. We contrast the results from Detrended Fluctuation Analysis (DFA) to a new method based on the Kramers–Moyal equation in scale. For very short term (< 12 hours), all price time series show positive temporal correlations (Hurst exponent H > 0.5) except for the intraday 15 minute market, which shows strong negative correlations (H < 0.5). For longer term periods covering up to two days, all price time series are anti-correlated (H < 0.5).

Industrial green technology innovation has become an important content in achieving high-quality economic growth and comprehensively practicing the new development concept in the new era. This paper measures the efficiency of industrial green technology innovation and regional differences based on Chinese provincial panel data from 2005 to 2018, using a combination of the super-efficient SBM model for considering undesirable outputs and the Dagum Gini coefficient method, and discusses and analyses the factors influencing of the industrial green technology innovation efficiency by constructing a spatial econometric model. The results show that: firstly, the industrial green technology innovation efficiency in China shows a relatively stable development trend, going through three stages: " stationary period", " recession period " and "growth period ". However, the efficiency gap between different regions is obvious, specifically in the eastern > central > western regions of China, and the industrial green technology efficiency innovation in the central and western regions is lower than the national average. Secondly, regional differences in the efficiency of industrial green technology innovation in China are evident but tend to narrow overall, with the main reason for the overall difference being regional differences. In terms of intra-regional variation, variation within the eastern region is relatively stable, variation within the central region is relatively low and shows an inverted 'U' shaped trend, and variation within the western region is high and shows a fluctuating downward trend. Thirdly, the firm size, government support, openness to the outside world, environmental regulations and education levels contribute to the efficiency of industrial green technology innovation. In addition, the industrial structure hinders the efficiency of industrial green technology innovation, and each influencing factor has different degrees of spatial spillover effects.

Next generation in-to-out-of body biomedical applications have adopted optical wireless communications (OWCs). However, by delving into the published literature, a gap is recognised in modeling the in-to-out-of channel, since most published contributions neglect the particularities of different type of tissues. Towards this direction, in this paper we present a novel pathloss and scattering models for in-to-out-of OWC links. Specifically, we derive extract analytical expressions that accurately describe the absorption of the five main tissues’ constituents, namely fat, water, melanin, oxygenated and de-oxygenated blood. Moreover, we formulate a model for the calculation of the absorption coefficient of any generic biological tissue. Next, by incorporating the impact of scattering in the aforementioned model we formulate the complete pathloss model. The developed theoretical framework is verified by means of comparisons between the estimated pathloss and experimental measurements from independent research works. Finally, we illustrate the accuracy of the theoretical framework in estimating the optical properties of any generic tissue based on its constitution. The extracted channel model is capable of boosting the design of optimized communication protocols for a plethora of biomedical applications.

The key concepts in symmetry detection and similarity, identity measures are automorphism and isomorphism respectively. Therefore, methods for symmetry detection and similarity, identity measures should be functionally bijective, inverse, and invariance under a set of mathematical operations. Nevertheless, few or no existing method is functional for these properties. In this paper, a new methodological paradigm, called optinalysis, is presented for symmetry detections, similarity, and identity measures between isoreflective or autoreflective pair of mathematical structures. The paradigm of optinalysis is the re-mapping of isoreflective or autoreflective pairs with an optical scale. Optinalysis is characterized as invariant under a set of transformations and its isoreflective polymorphism behaves on polynomial and non-polynomial models.

Evidence-based medicine (EBM) is in crisis, in part due to bad methods, which are understood as misuse of statistics that is considered correct in itself. This article exposes two related common misconceptions in statistics, the effect size (ES) based on correlation (CBES) and a misconception of contingency tables (MCT). CBES is a fallacy based on misunderstanding of correlation and ES and confusion with 2 × 2 tables, which makes no distinction between gross crosstabs (GCTs) and contingency tables (CTs). This leads to misapplication of Pearson’s Phi, designed for CTs, to GCTs and confusion of the resulting gross Pearson Phi, or mean-square effect half-size, with the implied Pearson mean square contingency coefficient. Generalizing this binary fallacy to continuous data and the correlation in general (Pearson’s r) resulted in flawed equations directly expressing ES in terms of the correlation coefficient, which is impossible without including covariance, so these equations and the whole CBES concept are fundamentally wrong. MCT is a series of related misconceptions due to confusion with 2 × 2 tables and misapplication of related statistics. The misconceptions are threatening because most of the findings from contingency tables, including CBES-based meta-analyses, can be misleading. Problems arising from these fallacies are discussed and the necessary changes to the corpus of statistics are proposed resolving the problem of correlation and ES in paired binary data. Since exposing these fallacies casts doubt on the reliability of the statistical foundations of EBM in general, we urgently need to revise them.

The knowledge of the optical properties of biological tissues in a wide spectral range is highly important for the development of noninvasive diagnostic or treatment procedures. The absorption coefficient is one of those properties, from which various information about tissue components can be retrieved. Using transmittance and reflectance spectral measurements acquired from ex vivo rabbit brain cortex samples, allowed to calculate its optical properties in the ultraviolet to the near infrared spectral range. Melanin and lipofuscin, the two pigments that are related to the ageing of tissues and cells were identified in the cortex absorption. By subtracting the absorption of these pigments from the absorption of the brain cortex, it was possible to evaluate the true ratios for the DNA/RNA and hemoglobin bands in the cortex – 12.33 fold (at 260 nm), 12.02 fold (at 411 nm) and 4.47 fold (at 555 nm). Due to the fact that the accumulation of melanin and lipofuscin increases with the ageing of the brain tissues and are related to the degeneration of neurons and their death, further studies should be performed to evaluate the evolution of pigment accumulation in the brain to prevent the development of Alzheimer, Parkinson and stroke pathologies in the brain.

We evaluate some binomial cubic Fibonacci sums.

Around the world, every year, about 17 million people death cause happen due to CardioVascular Diseases (CVD). As per clinical records, primarily sufferers exhibit myocardial infarctions and Heart Failures (HF). Creatinine is a Musculo - skeletal waste product. The kidneys filter creatinine from the blood and excrete it through the urine in a healthy body. High creatinine levels can suggest renal problems. Elevated Serum Creatinine (SC) has been well established in the HF. Patients’ electronic medical records can be used to quantify symptoms and other related clinical laboratory test values, which would then be utilized to direct biostatistics exploration to uncover patterns and associations that doctors would otherwise miss. The latest American Heart Association guidelines for 1500 mg/d sodium tend to be sufficiently relevant for patients with stage A and B with HF. In this article, we used a dataset of the year 2015 of heart patients records of 299 patients. The present paper used the data analytic and statistical tools to verify the significant differences between alive and dead patients’ SC and Serum Sodium (SS). It also demonstrates the impact of significant features on abnormal SC and SS on the Survival-Status levels. The Age-Group feature, which is derived from age attribute and, Ejection Fraction (EF), anemia, platelets, Creatinine Phosphokinase (CPK), Blood-Pressure (BP), gender, diabetes, and smoking-status were utilized to determine the potential contributing features to mortality with Cox regression model. The Kaplan Meier plot was used to investigate the overall pattern of survival concerning age-group. During pre-processing of the dataset, Age and SS were removed due to multicollinear features during performing machine learning algorithms experiments. This paper also predicted patients’ survival, age group, and gender using supervised machine learning classifiers. Detection of significant features would help in making informed decisions to balance the lifestyle of heart patients. The author revealed that the patient’s follow-up months, as well as SC, EF, CPK, and platelets, are sufficient key features to predict heart patient survival using Random Forest (RF) stratified 10-fold CV method with accuracy (96%) with 5% Standard Deviation (SD) from medical records dataset. We identified the age-group and gender of the patient, and the RF model outperformed others with the best accuracy 96% and 94% in both cases having 11% SD. Also, prominent features such as CPK, SC, follow-up month, platelets, and ejection were found to be significant factors in predicting the patient’s age-group. Smoking habits, CPK, platelets, follow-up month, and SC of each patient were discovered to be significant predictors of patient gender. The hypothetical study proved that SC and SS making substantial differences in the survival of patients (p &lt; 0.05) and failed to reject that anemia, diabetes, and BP making a significant impact on the creatinine and sodium of each patient (p &gt; 0.05). With χ2(1) = 8.565, the Kaplan Meier plot revealed that mortality was high in the extremely elder age-group. The finding has possible effects on clinical practice and becomes a new medical support system when predicting whether a patient can survive a heart attack or not. The doctor should primarily concentrate on follow-up month, SC and EF, CPK, and platelet count since the aim is to understand whether a patient survives after HF.

Herein, we report on a giant thermoelectric figure of merit of a non-degenerate fluorine-doped single-walled carbon nanotube (FSWCNT) using a tractable analytical approach and the phonon lattice Boltzmann model (LBM). We investigate the influence of the doping concentration, and the overlapping integrals on the ZT. The ZT and the temperature range of operation can be tuned using the doping (impurity) concentration and the overlapping integrals, respectively. The lattice thermal conductivity obtained using the phonon LBM was calculated to be 107.2 W/mK which yielded a ZT greater than 20. Interestingly, the ZT obtained is higher than what has been reported in superlattices, (ZT~1.4) and superlattice nanowire, (ZT~ 4) at 300 K, making FSWCNT a potential candidate for thermoelectric applications.

Camptothecin (CPT) is a potent anticancer drug, and its putative oral administration is envisioned although difficult due to physiological barriers that must be overcome. A comprehensive biophysical analysis of CPT interaction with biointerface models can be used to predict some pharmacokinetic issues after oral administration of this or other drugs. To that end, different models were used to mimic the phospholipid composition of normal, cancer, and blood-brain barrier endothelial cell membranes. The logD values obtained indicate that the drug is well distributed across membranes. CPT-membrane interaction studies also confirm the drug’s location at the membrane cooperative and interfacial regions. The drug can also permeate membranes at more ordered phases by altering phospholipid packing. The similar logD values obtained in membrane models mimicking cancer or normal cells imply that CPT has limited selectivity to its target. Furthermore, CPT binds strongly to serum albumin, leaving only 8.05% of free drug available to be distributed to the tissues. The strong interaction with plasma proteins, allied to the large distribution (VDSS=5.75 ± 0.932 L·Kg-1) and tendency to bioaccumulate in off-target tissues, were predicted to be pharmacokinetic issues of CPT, implying the need to develop drug delivery systems to improve its biodistribution.

We evaluate various binomial sums involving the powers of Fibonacci and Lucas numbers.

The design flood concept (DF) provides for an essential tool in designing the hydraulic works, in defining the reservoir operation programs and for a reliable flood hazard identification. Under a simplified approach, the maximum discharge and the floods volume are statistically processed to reasonably define the DF. Yet, the integral hydrograph provides additional key temporal and quantitative details of important significance for flood management and particularly for the res-ervoirs operation and associated risks of failures. The procedure presented in this paper (as applied on a set of compatibly shaped hydrographs) involves the following key stages: (i) normalize the floods, (ii) define similar flood shape classes and (iii) evaluate the average dimensionless flood (ADF) for each class. The ADFs are finally transformed into a set of (DF)s. Many statistical distributions approximate acceptably the frequent values of the maximum discharges or the flood volumes, yet displaying a significant spread for medium or rare probabilities of exceedance (PE). This scattering, which can be explained by the epistemic uncertainty, defines an area of uncertainty both for measured and extrapolated values. In considering upper and lower values of the uncertainty in-tervals as limits for maximum discharges and flood volumes, then by combining them compatibly, a set of DFs - as completely defined hydrographs, with different shapes - results for each PE. The herein proposed procedure defines both one peak DF and multi-peaks DF. Subsequently, such DFs do assist water managers in examining and establishing tailored approaches for a variety of input hydrographs. Among the DFs that would correspond to a same PE, the most compact floods arise a special interest, for they are basic in defining the set of safe operation rules for hydraulic structures.

During the conceptual and preliminary design stage of a ship, designers need to ensure that the selected principal dimensions and parameters are good enough to deliver a stable ship (statically and dynamically) besides deadweight and speed. To support this, the initial intact stability of the proposed ship is required to be calculated, and in doing so, the lightship weight and its detailed breakdown are necessary to be known. After hull steel weight, machinery weight, mainly, marine propulsion and power generation machinery, play a vital role in the lightship weight estimate of a ship due to its robustness. The correct estimation of respective weights improves the accuracy of calculating a ship's initial stability typically to be designed and built. Hence, it would be advantageous for the designer to convince the ship owner. A total of 3006 marine propulsion (main marine diesel) engines and 348 power generation (auxiliary marine diesel) engines/generators of various power output (generators output for auxiliary engines), engine RPM and cylinder number of different engine makers are collected. These are analyzed and presented in both tabular and graphical forms to demonstrate the possible relationship between marine propulsion engine weight and power generation engine weight, and their respective power output, RPM, cylinder number, power-RPM ratio and power-RPM ratio per cylinder.In this article, the authors have attempted to investigate the behavior of marine propulsion engine weight and power generation engine/generator weight regarding engine power output, generator power output, engine RPM and cylinder number (independent variables). Further attempts have been made to identify those independent variables that influence the weight of the marine propulsion engine and power generation engine/generator (dependent variables), and their interrelationships. A mathematical model has thus been developed and proposed, as a guiding tool, for the designer to estimate the weight of main and auxiliary engines more accurately during the conceptual and preliminary design stage.

The continuing development of industrialization and increasing population density has led to the emergence of noise as an increasingly common problem, requiring various types of sound absorption and insulation methods to address it. Meanwhile, the recycling of resources to ensure a sustainable future for the planet and mankind is also required. Therefore, this study investigates the potential of corrugated cardboard as a resource for noise reduction. The sound absorption and insulation performance of non-perforated corrugated cardboard (NPCC) were measured, and modified corrugated boards were fabricated by drilling holes either through the surface of the corrugated board alone or through the corrugated board in its entirety. The sound absorption/insulation performance both of perforated corrugated cardboard (PCC), and perforated corrugated cardboard with multi frequency resonators (PCCM) were measured using the transfer function method and the transmission matrix method. To determine the effectiveness of NPCC, PCC, and PCCM in noise reduction, the sound pressure level was analyzed by applying it to a home blender. The results showed PCCM’s sound absorption and insulation performance to be excellent. On the basis of these findings, we propose the use of PMMC as an eco-friendly noise reduction material.

Air change rate is an important parameter for quantification of ventilation heat losses and also affects the indoor climate of buildings. Indoor air quality is significantly associated with ventilation. If air change isn't sufficient, trapped allergens, pollutants and irritants can degrade the indoor air quality and affect the well-being of a building's occupants. Many studies on ventilation and health have concluded that lower air change rates can have a negative effect on people’s health and low ventilation may result in an increase in allergic diseases. Quantification of air change rate is complicated, since it is affected by a number of parameters, of which the one of the most variable is the air-wind flow. This study aims to determination and comparison of values of the air change rate in two methods - by quantifying of aerodynamic coefficient Cp = Cpe - Cpi – so called aerodynamic quantification of the building and the methodology based on experimental measurements of carbon dioxide in the selected reference room in apartment building.

Complex modeling has received significant attention in recent years and is increasingly used to explain the statistical phenomenon with increasing and decreasing fluctuations such as the similarity or difference of spike protein charge patterns of coronaviruses. Different from the existing covariance or correlation coefficient methods in traditional integer dimension construction, this study proposes a simplified novel fractional dimension derivation with the exact Excel tool algorithm. It involves the fractional center moment extension to covariance, which ends up a complex covariance coefficient that is better than the Pearson correlation coefficient, in the sense that the nonlinearity relationship can be further depicted. The spike protein sequences of coronaviruses were obtained from the GenBank and GISAID database, including the coronaviruses from pangolin, bat, canine, swine (three variants), feline, tiger, SARS-CoV-1, MERS, and SARS-CoV-2 (including the strains of Wuhan, Beijing, New York, German, and UK variant B.1.1.7) were used as the representative examples in this study. By examining the values above and below the average/mean based on the positive and negative charge patterns of the amino acid residues of the spike proteins from coronaviruses, the proposed algorithm provides deep insights into the nonlinear evolving trends of spike proteins for understanding the viral evolution and identifying the protein characteristics associated with viral fatality. The calculation results demonstrate that the complex covariance coefficient analyzed by this algorithm is capable of distinguishing the subtle nonlinear differences in the spike protein charge patterns with reference to Wuhan strain SARS-CoV-2 for which the Pearson correlation coefficient may overlook. Our analysis reveals the unique convergent (positive correlative) to divergent (negative correlative) domain center positions of each virus. The convergent or conserved region may be critical to the viral stability or viability; while the divergent region is highly variable between coronaviruses suggesting high frequency of mutations in this region. The analyses show that the conserved center region of SARS-CoV-1 spike protein is located at amino acid residues 900, but shifted to the amino acid residues 700 in MERS spike protein, and then to amino acid residues 600 in SARS-COV-2 spike protein, indicating the evolvement of the coronaviruses. Interestingly, the conserved center region of the spike protein in SARS-COV-2 variant B.1.1.7 shifted back to amino acid residues 700, suggesting this variant is more virulent than the original SARS-COV-2 strain. Another important characteristic our study reveals is that the distance between the divergent mean and the maximal divergent point in each of the viruses (MERS>SARS-CoV-1>SARS-CoV-2) is proportional to viral fatality rate. This algorithm may help to understand and analyze the evolving trends and critical characteristics of SARS-COV-2 variants, other coronaviral proteins and viruses.

The load on the top of a slope is an important cause of slope failure, and it is of great significance to study the relationship between the load and the stability of the slope. This paper uses elastic theory and Moore Coulomb's theory as transformation conditions to obtain the slope stability coefficient expression under slope top load based on the Swedish slice method. In view of the actual engineering, the corresponding slope model structure was established, and 5 sliding surfaces were set with the crack on the top of the slope as the shear outlet. According to the slope stability coefficient expression, the stability coefficient of the set sliding surface is solved. The result shows that the slope is unstable under the load. The judgment result is consistent with the GEO-STUDIO check calculation result. This method can provide reference for theory and engineering practice.

We calculate the hydrodynamic forces exerted on an oscillating circular cylinder when it moves translationally perpendicular to its axis in the infinitely deep water covered by compressed ice. The cylinder can oscillate both horizontally and vertically. In the linear approximation, we find a solution for the steady wave motion generated by the cylinder within the hydrodynamic set of equations for the incompressible ideal fluid. We show that depending on the rate of ice compression, the normal and anomalous dispersion can occur in the system. In the latter case, the group velocity can be opposite to the phase velocity in a certain range of wavenumbers. We investigate the dependences of the hydrodynamic loads (added mass, damping coefficients, wave resistance, and lift force) exerting on the cylinder on the translational velocity and frequency of oscillation. It is shown that there is a possibility of the appearance of negative values for the damping coefficients at the relatively big cylinder velocity; then the wave resistance decreases with increasing of cylinder velocity. The theoretical results are underpinned by the numerical calculations for the real parameters of ice and cylinder motion.

The paper presents attribute based characterization of nanomaterials method for computer storage and retrieval as knowledgebase. The knowledgebase permits indepth understanding and comparison between nanomaterials available with the scientists and product developers to satisfy their research and development (R & D) needs. Techniques for order preference by similarity to ideal solution (TOPSIS) is proposed to evaluate nanomaterials in the presence of multiple attributes. The method normalizes attributes to nullify the effect of different units and their values in the range of 0 to 1. The relative importance of different attributes for different applications is considered. The weight vector is derived using Eigen value formulation. The positive and negative benchmark solutions are derived. Euclidean distance of alternatives from these best and worst solution leads to the development of proximity /goodness/suitability index for ranking. Final decision is taken by decision makers by SWOT analysis and short and long term strategies of the organisation. The methodology is illustrated with the help of an example and step-by-step procedure. Results, discussion and conclusion highlights the importance and practical application.

This paper presents results on tribological characteristics for polymer blends made of polybutylene terephthalate (PBT) and polytetrafluoroethylene (PTFE). This blend is relatively new in research as PBT has restricted processability because of its processing temperature near the degradation one. Tests were done block-on-ring tribotester, in dry regime, the variables being the PTFE concentration (0%, 5%, 10% and 15%wt) and the sliding regime parameters (load: 1 N, 2.5 N and 5 N, the sliding speed: 0.25 m/s, 0.5 m/s and 0.75 m/s, and the sliding distance: 2500 m, 5000 m and 7500 m). Results are encouraging as PBT as neat polymer has very good tribological characteristics in terms of friction coefficient and wear rate. SEM investigation reveals a quite uniform dispersion of PTFE drops in the PBT matrix.

Bohrnstedt’s (1969) attempt to derive a formula to compute the partial correlation coefficient and simultaneously correct for attenuation sought to simplify the process of performing each task separately. He suggested that his formula, developed from algebraic and psychometric manipulations of the partial correlation coefficient, produces a corrected partial correlation value. However, an algebraic error exists within his derivations. Consequently, the formula proposed by Bohrnstedt does not appropriately represent the value he intended it to estimate. By correcting the erroneous step and continuing the derivation based upon his proposed procedure, the steps outlined in this paper ultimately produce the formula that Bohrnstedt desired.

The general coupling between particle transport and ionization-recombination processes in hot plasma is considered on the key concept of equilibrium charge state (CS) transport. A theoretical interpretation of particle and CS transport is gained in terms of a two-dimensional (2D) Markovian stochastic (random) processes, a discrete 2D Fokker-Plank-Kolmogorov equation (in charge and space variables) and generalized 2D coronal equilibrium between atomic processes and particle transport. The basic tool for analysis of CS equilibrium and transport is the equilibrium cell (EC) (two states on charge and two on space), which presents (i) a unit phase volume, (ii) the characteristic scale of local equilibrium, (iii) a comprehensive solution for the simplest nonlinear relations between transport and atomic processes. The approach opens up new perspectives on transport studies: (i) the direct modelling of equilibrium and transport of impurity using the atomic data base, (ii) recovery of the complete recombination rate profile based on knowledge of density profiles and ionization rate profiles, (iii) the local transport analysis, based on the reduction of the equilibrium set to the single EC (in particular, central or edge), (iv) analysis of the reduced transport coefficients (diffusion and convection) on the density profile measurements.

Information overload is the biggest challenges nowadays for any website, especially the e-commerce website. However, this challenge arises for the fast growth of information on the web (WWW) with easy access to the internet. Collaborative filtering based recommender system is the most useful application to solve the information overload problem by filtering relevant information for the users according to their interests. But, the existing system faces some significant limitations like as data sparsity, low accuracy, cold-start and malicious attacks. To alleviate the mentioned issues, the relationship of trust incorporates in the system where it can be between the users or items, and such system is known as the trust-based recommender system (TBRS). From the user perspective, the motive of the TBRS is to utilize the reliability between the users to generate more accurate and trusted recommendations. However, the aim of the paper is to present a comparative analysis of different trust metrics in the context of the type of trust definition of TBRS. Also, the study accomplishes on twenty-four trust metrics in terms of the methodology, trust properties &amp; measurement, validation approaches, and the experimented dataset.

We consider the inverse function $z=g(w)$ of a (normalized) starlike function $w=f(z)$ of order $\alpha$ on the unit disk of the complex plane with $0<\alpha<1.$ Krzy{\. z}, Libera and Z\l otkiewicz obtained sharp estimates of the second and the third coefficients of $g(w)$ in their 1979 paper. Prokhorov and Szynal gave sharp estimates of the fourth coefficient of $g(w)$ as a consequence of the solution to an extremal problem in 1981. We give a straightforward proof of the estimate of the fourth coefficient of $g(w)$ together with explicit forms of the extremal functions.

Metallic substrates and polymer adhesive in composite-metal joints have a relatively large coefficient of thermal expansion (CTE) mismatch, which is a barrier in the growing market of electric vehicles and their battery structures. It is reported that adding carbon nanotubes (CNTs) to the adhesive reduces the CTE of the CNT enhanced polymer adhesive multi-material system, therefore when used in adhesively bonded joints it would, theoretically, result in low CTE mismatch in the joint system. The current article presents the influence of two specific mass ratios of CNTs on the CTE of the enhanced polymer. It was observed that the addition of 1.0 wt% and 2.68 wt% of multi-walled CNTs (MWCNTs) decreased the CTE of the polymer adhesive from 7.5e-5 1/C (pristine level) to 5.87e-5 1/C and 4.43e-5 1/C, respectively by 22% and 41% reduction. The reduction in the CTE was predicted, theoretically, which showed that CTE should have been reduced to 3.6e-5 1/C (52% reduction) and 1.4e-5 1/C (81% reduction). This may be due to the fact that, Raman spectroscopy of the MWCNTs identified defects in the raw material, and scanning electron microscopy (SEM) identified agglomeration of MWCNTs on the surface and cross-section of the modified polymers.

The study of the optical properties of biological tissues for a wide spectral range is necessary for the development and planning of noninvasive optical methods to be used in clinical practice. In this study, we propose a new method to calculate almost all optical properties of tissues as a function of wavelength directly from spectral measurements. Using this method and with the exception of the reduced scattering coefficient, which was obtained by traditional simulation methods, all the other optical properties were calculated in a simple and fast manner for human and pathological colorectal tissues. The obtained results are in good agreement with previous published data, both in magnitude and in wavelength dependence. Since this method is based on spectral measurements and not on discrete-wavelength experimental data, the calculated optical properties contain spectral signatures that correspond to major tissue chromophores such as DNA and hemoglobin. Analysis of the absorption bands of hemoglobin in the wavelength dependence of the absorption spectra of normal and pathological colorectal mucosa allowed to identify differentiated accumulation of a pigment in these tissues. The increased content of this pigment in the pathological mucosa may be used for the future development of noninvasive diagnostic methods for colorectal cancer detection.

There is an accelerating requirement for ocean sensing where autonomous vehicles can play an essential role in assisting engineers, researchers, and scientists with environmental monitoring and collecting oceanographic data. This paper is performed to develop a rigid sail for the autonomous sailing drone. Our study aims to numerically analyze the aerodynamic characteristics of curvy twin sail and compare it with wing sail. Because racing regulations limit the sail shape, only the two-dimensional geometry was open for an optimization. Therefore, this study’s first objective was to identify the aerodynamic performance of such curvy twin sails. Simultaneously, a secondary objective was to estimate the effect of the sail’s spacing and shapes. A viscous Navier-Stokes flow solver is used for the numerical aerodynamic analysis. The 2D aerodynamic investigation is a preliminary evaluation. The results have shown that the curvy twin sail designs have improved lift, drag, and driving force coefficient compared to the wing sails. The spacing between the port and starboard sails of curvy twin sail is an important parameter. The spacing is 0.035L, 0.07L, and 0.14L shows the lift coefficient reduction because of dramatically stall effect, while flow separation is improved with spacing is 0.21L, 0.28L, and 0.35L. Significantly, the spacing 0.28L shows the maximum high pressure at the lower area and the small low pressure area at leading edges, so the highest lift is generated.

This document makes a comprehensive analysis of the inequality of the water market in Chile, measured by the Gini coefficient method. The situation of water rights in Chile is of particular interest because it is a completely privatized system, where rights are traded in the market and therefore water is presented as a commodity. This privatization of water in Chile occurred as part of the process of neoliberalization since the 1981 Water Code. The results of this study indicate that both the concentration and the inequality in the distribution of water rights is very high. It proposes a profound revision of applying a mercantile logic to a scarce basic resource for life such as water and exploring the importance of its role as a national good for public use.

Electrode is a key component in a microbial electrolysis cell (MEC) and it needs significant improvement for practical implementation of MEC. For effective development of electrode technology, accurate and reproducible analytical methods are very important. Linear sweep voltammetry (LSV) is an essential analytical method for evaluating electrode performance; however, it has not been firmly established yet in the MEC field. In this study, biological brush (BB), abiotic brush (AB), Pt wire (PtW), stainless steel wire (SSW) and mesh (SSM)) were tested to explore the most suitable counter electrode in different medium conditions. Coefficient of variation (CV) for Imax of LSV were comparatively analyzed. In BB-anode LSV, SSW (0.48%) and SSM (2.17%) showed higher reproducibility as a counter electrode. In SSM-cathode LSV, BB (1.76%) and PtW (2.01%) produced more reproducible results. In the Ni-AC-SSM-cathode LSV, PtW (3.54%) and BB (8.81%) produced more reproducible result. It shows electrode used in the operation is an appropriate counter electrode in the acetate-added condition. However, in the absence of acetate, PtW (1.24%) and BB (1.71%) produced more reproducible results in SSM cathode and PtW (0.61%) and SSW (1.21%) did in the Ni-AC-SSM-cathode, showing PtW is an appropriate counter electrode. These results also shows that PtW is an appropriate counter electrode in cathode LSV.

Determining disability prevalence is an important area for population statistics, especially among young adolescents. The Washington Group on Disability Statistics is one source of reporting disabilities through functional difficulties. However, young adolescents self-reporting this measure is in its infancy. The purpose of this study was to carry out an intra-rater test-retest reliability study on a modified set of items for self-reporting functional difficulties. Young adolescents (n=74; boys=64%; age m=13.7, SD=1.8) completed a self-reported version of the child functioning module in a supervised classroom. The second administration took place two weeks later. Intraclass correlation coefficient (ICC) and Kappa (k) statistics were used to test reliability of the items, and interpretation through Landis &amp; Koch, and Cohen, respectively. The majority of items had substantial or moderate agreement, although there was only fair agreement for self-care (ICC=0.59), concentration (ICC=0.50), and routine (ICC=0.54). Kappa statistics of behaviour were interpreted to be large (k=0.65), and seeing (k=0.49), walking (k=0.49), and speaking (k=0.49) difficulties were moderate. The majority of the items in the self-reported version of the child functioning module can be used in a scale format, although some caution may be required on items of self-care and concentration when used as a dichotomous variable.

The main goal of our work is the revealing of problematic issues related to estimates of the absorption coefficient of colored organic matter in the northern seas from data of the Ocean and Land Color Instrument (OLCI) on the Sentinel-3 satellites. In particular, a comparison of the OLCI standard error estimates ADG443_NN_err., relating to the measurement and retrieval of the geophysical products, with the uncertainties in the real situation of the northern seas, where the natural conditions are extremely unfavorable (first of all, frequent cloudiness, low Sun heights). We conducted a comprehensive multi-sensor study of the uncertainties using various approaches, first at all, directly comparing the data from satellite (OLCI Sentinel-3 and four other ocean color sensors) and field measurements in five sea expeditions 2016-2019, by using the different processing algorithms. Our analysis has shown that the real uncertainties of the final product are significantly higher than the calculated errors of the ADG443_NN_err., which is 100% and ~10%. The main reason for that is the unsatisfactory atmospheric correction. We present the results of the analysis of the different effecting factors (satellite sensors, processing algorithms, use of the other parameters), and formulate the tasks of future work.

We investigate the tunneling of quasiparticles through a potential barrier of finite height and width, in a system with a band structure consisting of a quadratic band crossing point (QBCP). We compute the results of the transmission coefficient at various incident angles, and also the conductivity and the Fano factor. We discuss the distinguishing signatures of these transport properties in comparison with other semimetals, as well as electrons in normal metals.

Construction and demolition waste (CDW) represents 1/3 of the weight of all-waste produced. Increasing their recycling and reutilization with recycled aggregates (RA) means closing the life cycle of construction materials. Research has been carried out on artificial aggregates from the exclusive crushing of structural concrete waste in selective demolitions (CDWRConc). This study analyses the use of recycled concrete as graded aggregate (GARConc) and in cement soil (CSRConc). The material complies with the requirements as a road base, although due to the low values of resistance to fragmentation these materials are adequate for use in sensitive road systems and other places such as urban roads and car parks. The sensitive road systems are infrastructures in places of great natural wealth and low traffic intensity, with an annual average of heavy vehicle traffic (AADTh) below 50 vhp/d. As soluble salt contents have been detected, additional waterproofing or drainage measures must be adopted to prevent water infiltration into the layers made up of CDWRHorm. Finally, the high initial values of UCS allow the temporary passage of light vehicles over CSRConc after 3 days.

In social sciences, a plethora of studies utilize nominal data to establish the relationship between the variables. This, in turn, requires the correct use of correlation technique. The choice of correlation technique depends upon the underlying assumptions and power of the test of significance. The objective of the research is to explore the best measure of association for nominal data in terms of size, power and bias in estimation. Monte Carlo simulations reveal that the Phi and Pearson correlation statistics performs equally well in terms of size, power, and bias for naturally dichotomous variables. When both variables are artificially dichotomized, the Tetrachoric statistic has an edge in terms of bias to Pearson correlation statistic. If one variable is continuous and other is artificially dichotomized, the Biserial correlation measure turns out to be less biased as compared to Pearson statistic although both statistics exhibit similar power and size properties. If one variable is continuous and other is naturally dichotomized, it is hard to choose between the Point Biserial and Pearson correlation measures. Finally, if one variable is naturally dichotomous and other is artificially dichotomized, correlation coefficient V is compared with Pearson, Phi and Tetrachoric correlation techniques in terms of bias in estimate. The results indicate that the Tetrachoric statistic considerably overestimates the correlation value against non-normal distributions. Pearson and Phi correlation slightly underestimate the correlation value. In contrast, the correlation statistic V perform well.

Background: Malaria is one of the most common diseased conditions across most developing countries caused by one of four species of Plasmodium. P. falciparum and P.vivax are the main agents responsible for malaria in Nigeria. Malarial infection has been shown to be associated with abnormalities in fluids, electrolytes and acid base balances. Electrolyte imbalance and mineral disturbances are majorly identified clinical symptoms in various infectious diseases including malaria. Electrolyte imbalance in malarial infection is capable of enhancing disease severity. The aim of this study was to investigate the effects of malarial infection on electrolytes parameters. Methods: Finger prick blood samples, Thick and Thin Giemsa-stained blood smears, were collected from 100 malaria-suspected individuals representing all age groups. The Giemsa-stained blood smears were examined microscopically. Demographic information was obtained using structured questionnaires. The electrolytes levels (Na, K, Cl^- and HCO_3-) in malarial patients were analyzed using standard procedures, Pearson's Correlation Coefficient correlation technique was used to investigate the relationship, and the strength of association between the variables. Results: The mean bound of patients’ sodium level was observed to fall within the specified normal limits of 125mmol/L – 145mmol/L; except for positive malaria patients belonging to the MP-(++) which will fall below the 125mmol/L (i.e. 126.25mmol/L – 1.77mmol/L = 124.48mmol/L). The spread of the sodium data taken from the patients were observed to fall within the normal limits leaving only the boxplot’s lower whisker out, that is, observations falling within the first quartile, except for MP-(++) patients with observations in the first to second quartile spreading outside the normal lower limit, in contrast for the negative tested patients, the box and its whiskers were almost engulfed within the normal limits. Conclusion: In our study we found that Plasmodium falciparum altered more in electrolytes parameters than Plasmodium vivax. The biochemical markers can be used as biomarkers to confirmation of malaria. This study discovered a significant linear relationship based on the Pearson product-moment correlation between creatinine and urea, potassium and chloride, potassium and creatinine, potassium and urea. The mean sodium and chloride level of positive malaria [MP-(++)] patients were observed to fall outside the normal limit.

The steering performance according to the steering angle control was tested by using the active steering bogie developed to reduce excessive wheels and rail wear and noise generated when the railway vehicle run in a curved section. As a result of the test of increasing the steering angle in accordance with the target steering angle in the 300m radius of curvature, the bogie is gradually aligned in the radial steering position, and when the control is carried out to 100% of the target steering angle, the bogie angles of the front and rear bogies appeared almost the same. As the steering angle increased, wheel lateral force and derailment coefficient also decreased. Therefore, the validity of the radial steering position control method applied in this paper was confirmed experimentally. This test results will be used for future research on active steering bogie commercialization.

Aims: The lack of information about the inter variability of the test results obtained by CLSI and EUCAST requires further clarifications to interpret antimicrobial susceptibility patterns better. This study aimed to compare the CLSI and EUCAST interpretations of the antimicrobial susceptibility test results of the ESBL–producing uropathogenic Escherichia coli and Klebsiella pneumonia strains. Methods: After obtaining 157 ESBL-producing E. coli and 95, ESBL-producing K. pneumonia isolates from the urine specimens of the patients, Kirby-Bauer’s disc diffusion method was used for conducting antimicrobial susceptibility test. The test procedures and the interpretation of the results were carried out according to the year 2017 versions of both of the two guidelines. For the statistical comparison of concordance between the two guidelines, the Kappa coefficients and the concordance rates were calculated. Results: The results were graded in the range from perfect to poor agreement. For E. coli, interpretations of the AST results revealed a moderate to perfect agreement between both methods. Weighted Kappa agreement scores in the range from 0.42 to 1. The agreement for AMC, TPZ30/6, ceftazidime 10, meropenem, and aztreonam was poor without any inconsistencies. For Klebsiella, the kappa agreement score was in the range from 0.25 to 1. It was incompatible with AMC, TPZ 30/6, ceftazidime 10, aztreonam; there was poor agreement for cefepime, amikacin and ertapenem. Conclusions: Our results showed agreement between the two guidelines for uropathogenic extended-spectrum ß-lactamase producing Escherichia coli and Klebsiella pneumoniae but also showed inconsistencies between two guidelines. Therefore, the results of our study contribute to the comparison of these guidelines for interpreting antibiotic susceptibilities.

The ongoing outbreak of the novel coronavirus pneumonia (also known as COVID-19) has triggered a series of stringent control measures in China, such as city closure, traffic restrictions, contact tracing and household quarantine. These containment efforts often lead to changes in the contact pattern among individuals of the population. Many existing compartmental epidemic models fail to account for the effects of contact structure. In this paper, we devised a pairwise epidemic model to analyze the COVID-19 outbreak in China based on confirmed cases reported during the period February 3rd--17th, 2020. By explicitly incorporating the effects of family clusters and contact tracing followed by household quarantine and isolation, our model provides a good fit to the trajectory of COVID-19 infections and is useful to predict the epidemic trend. We obtained the average of the reproduction number $R=1.494$ ($95\%$ CI: $1.483-1.507$) for Hubei province and $R=1.178$ ($95\%$ CI: $1.145-1.158$) for China (except Hubei), suggesting that some existing studies may have overestimated the reproduction number by neglecting the dynamical correlations and clustering effects. We forecasted that the COVID-19 epidemic would peak on February 13th ($95\%$ CI: February $9-17$th) in Hubei and 6 days eariler in the regions outside Hubei. Moreover the epidemic was expected to last until the middle of March in China (except Hubei) and late April in Hubei. The sensitivity analysis shows that ongoing exposure for the susceptible and population clustering play an important role in the disease propagation. With the enforcement of household quarantine measures, the reproduction number $R$ effectively reduces and epidemic quantities decrease accordingly. Furthermore, we gave an answer to the public concern on how long the stringent containment strategies should maintain. Through numerical analysis, we suggested that the time for the resumption of work and production in China (except Hubei) and Hubei would be the middle of March and the end of April, 2020, respectively. These constructive suggestions may bring some immeasurable social-economic benefits in the long run.

This paper proposes a model based on gene expression programming for predicting discharge coefficient of triangular labyrinth weirs. The parameters influencing discharge coefficient prediction were first examined and presented as crest height ratio to the head over the crest of the weir (p/y), crest length of water to channel width (L/W), crest length of water to the head over the crest of the weir (L/y), Froude number (F=V/√(gy)) and vertex angle () dimensionless parameters. Different models were then presented using sensitivity analysis in order to examine each of the dimensionless parameters presented in this study. In addition, an equation was presented through the use of nonlinear regression (NLR) for the purpose of comparison with GEP. The results of the studies conducted by using different statistical indexes indicated that GEP is more capable than NLR. This is to the extent that GEP predicts the discharge coefficient with an average relative error of approximately 2.5% in such a manner that the predicted values have less than 5% relative error in the worst model.

Temporary changes in precipitation may lead to sustained and severe drought or massive floods in different parts of the world. Knowing variation in precipitation can effectively help the water resources decision-makers in water resources management. Large-scale circulation drivers have a considerable impact on precipitation in different parts of the world. In this research, the impact of El Niño-Southern Oscillation (ENSO), Pacific Decadal Oscillation (PDO), and North Atlantic Oscillation (NAO) on seasonal precipitation over Iran was investigated. For this purpose, 103 synoptic stations with at least 30 years of data were utilized. The Spearman correlation coefficient between the indices in the previous 12 months with seasonal precipitation was calculated, and the meaningful correlations were extracted. Then the month in which each of these indices has the highest correlation with seasonal precipitation was determined. Finally, the overall amount of increase or decrease in seasonal precipitation due to each of these indices was calculated. Results indicate the Southern Oscillation Index (SOI), NAO, and PDO have the most impact on seasonal precipitation, respectively. Also, these indices have the highest impact on the precipitation in winter, autumn, spring, and summer, respectively. SOI has a diverse impact on winter precipitation compared to the PDO and NAO, while in the other seasons, each index has its special impact on seasonal precipitation. Generally, all indices in different phases may decrease the seasonal precipitation up to 100%. However, the seasonal precipitation may increase more than 100% in different seasons due to the impact of these indices. The results of this study can be used effectively in water resources management and especially in dam operation.

Understanding of reflection characteristics of coastal seawalls is crucial for design. Wave reflection can cause difficulties to small vessel manoeuvring at the harbour entrance and constitute damaging scouring at the toe of coastal structures. Previous studies have considered reflection characteristics of coastal seawalls under wind-generated random waves without paying attention to the effects of wave bimodality created by the presence of swell waves. The present study focuses on the influence of random wave bimodality on reflective characteristics of coastal seawalls. More than eight hundred experimental tests have been conducted to examine the reflection performance of impermeable sloping seawalls under bimodal waves. Reflection coefficients were computed from each test. Analysis of results suggests that both unimodal and bimodal waves give similar reflection characteristics. However, the reflection coefficient in bimodal sea states seems to be more prolonged than in the unimodal sea states. It was found that the reflection coefficient of coastal seawalls is strongly influenced by the seawall slope, the wave steepness, relative water depth, and the surf similarity parameters. A new empirical reflection equation to describe the influence of wave bimodality on the reflection characteristics of coastal seawalls has been formulated based on this study.

The World Health Organization(WHO) in 2016 considered mHealth as: “the use of mobile wireless technologies including smart devices such as smartphones and smartwatches for public health” as an important resource for health services delivery and public health given their ease of use, broad reach and acceptance. WHO emphasizes the potential of this technology to increase access to health information, services and skills as well as promoting positive changes in health behaviors and management of diseases. In this regard, the capability of smartphones and smartwatches for m-health monitoring as well as verification of the patient the signal has become an important component of mHealth system. Most of the smartwatches could extract more than one bioelectrical signal therefore, therefore they provide suitable platform for extracting health data for e-monitoring. The existing approaches have not considered the integrity of data obtained from these smart devices. Therefore, it is important that the integrity of the collected data be verified continuously through user authentication. This could be done using any of the bioelectrical signals extracted and transmitted for e-monitoring. In this article, a smartwatch is used for extracting bioelectrical signal before decomposing the signal into sub-bands of Detail and Approximation Coefficient for user authentication. To select suitable features using biorthogonal wavelet decomposition of signal from a non-intrusive extraction, a detailed experiment is conducted extracting suitable statistical features from the bioelectrical signal from 30 subjects using different biorthogonal wavelet family. Ten features are extracted using Biorthogonal wavelet to decompose the signal into three levels of sub-band Detail and Approximation Coefficient and features extracted from each level the decomposed Detail and Approximation Coefficients. Comparison analysis is done after the classification of the extracted features based on the Equal Error Rate (EER). Using Neural Network (NN) classifier, Biorthogonal Wavelet Detail Coefficient Sub-band level 3 of bior1.1 achieved the best result of EER 13.80% with the fusion of the best sub-band three levels of bior1.1 achieving a better result of 12.42% EER.

To address three important issues related to extraction of water features from Landsat imagery, i.e., selection of water indexes and classification algorithms for image classification, collection of ground truth data for accuracy assessment, this study applied four sets (ultra-blue, blue, green, and red light based) of water indexes (NWDI, MNDWI, MNDWI2, AWEI_ns, and AWEI_s) combined with three types of image classification methods (zero-water index threshold, Otsu, and kNN) to 24 selected lakes across the globe to extract water features from Landsat-8 OLI imagery. 1440 (4x5x3x24) image classification results were compared with the extracted water features from high resolution Google Earth images with the same (or ±1 day) acquisition dates through computing the Kappa coefficients. Results show the kNN method is better than the Otsu method, and the Otsu method is better than the zero-water index threshold method. If the computational cost is not an issue, the kNN method combined with the ultra-blue light based AWEI_ns is the best method for extracting water features from Landsat imagery because it produced the highest Kappa coefficients. If the computational cost is taken into account, the Otsu method is a good choice. AWEI_ns and AWEI_s are better than NDWI, MNDWI and MNDWI2. AWEI_ns works better than AWEI_s under the Otsu method, and the average rank of the image classification accuracy from high to low is the ultra-blue, blue, green, and red light-based AWEI_ns.

Optinalysis, as a method of symmetry detection, is a new algorithm that intrametrically (within elements or variables) or intermetrically (between elements or variables) computes and compares two or more univariate or multi-clustered or multivariate sequences as a mirror-like reflection of each other (optics-like manner), hence the name is driven. Optinalysis is based by the principles of reflection and moment about a symmetrical line which detects symmetry that reflects a similarity measurement. This proposed methodology was validated in comparison with Pearson method of skewness detection, and also with some algorithms for pairewise alignment and comparison of genomic sequences (Needle, Stretcher, Water, Matcher) on EMBL-EBI website. A results comparison shows that optinalysis is more advance, more sensitive, more inferential and simple alternative approach of skewness detection and pairewise sequence comparison.

The effect of sensitivity points (sequence order and position of every element) of sequences following comparative optinalysis under two proposed mechanisms, the paranodic and synodic skewization, was studied to develop a modeling approach to comparative optinalysis of sequences. The results show that the outcomes of comparative optinalysis (similarity measurement) in a set of paranodically skewed sequences can be modeled deterministically by suitable line regression functions. The sensitivity points (nodes) of a sequence display two important and distinct zones, the K-zones and the B-zones. Continues paranodic skewization within these zones (KB zones) operates within probability space, but at hyperskewization level and at the K-zones only, the outcomes of comparative optinalysis operate outside the probability space. Moreover, the outcomes of comparative optinalysis by synodic skewization can be modeled deterministically by some regression line functions, but a general regression function cannot be identified. At certain limit of skewization value space, following paranodic and synodic skewization, the outcomes of comparative optinalysis at the left-sided sequence form a similar pattern with the right-sided sequence.

The diffusion coefficients of ions are measured in a microchip filled with a cationic charged 3D hydrogel in order to study the effect of cationic charged 3D hydrogel on the diffusivity of ions. In this study, poly-diallyl-dimethyl-ammoniumchloride (poly-DADMAC) is used to produce a 3D hydrogel. Four different fluorophores are used in the 3D hydrogel rhodamine 6G, rhodamine-BSA, fluorescein isothio-cyanate (FITC) and FITC-BSA. The rhodamine 6G and rhodamine-BSA are positively charged (cations), while fluorescein isothio-cyanate (FITC) and FITC-BSA are negatively charged (anions). Two widely used techniques which are short time diffusivity measurement technique and long time diffusivity measurement techniques are used to measure the diffusion coefficients. For the short time measurement, Fluorescence recovery after photo-bleaching (FRAP) is used by a 3D confocal microscope. For the long time measurement, fluorescence images are taken for 11 days to observe a pure diffusivity without any convective movement. As a result, the diffusivity of the cations was found to be lower than that of the anions in the cationic charged hydrogel.

The basic equation for estimating the aerodynamic power captured by an Anderson Vertical Axis Wind Turbine (AVAWT) is a solution of the Navier-Stokes(N-S) equations for a baroclinic, inviscid flow. In a nutshell, the pressure difference across the AVAWT is derived from Bernoulli’s equation; an upshot of the integration of the N-S momentum equation for a baroclinic inviscid flow, Euler’s momentum equation. The resulting expression for the pressure difference across the AVAWT rotor is plotted as a function of freestream speed. Experimentally determined airstream speeds at the AVAWT inlet and outlet, coupled with corresponding freestream speeds are used in estimating the aerodynamic power captured. The aerodynamic power is subsequently used in calculating the aerodynamic power coefficient of the AVAWT. The actual power coefficient is calculated from the power generated by the AVAWT at various free stream speeds and plotted as a function of the latter. Experimental results show that, at all free stream speeds and tip speed ratios, the aerodynamic power coefficient is higher than the actual power coefficient of the AVAWT. Consequently, the power generated by the AVAWT prototype is lower than the aerodynamic power captured, given the same inflow wind condition.

In South Korea, landslides are caused by localized heavy rainfall and typhoons, which often occur in the summer season at natural slopes in mountainous areas and artificial slopes in urban surroundings. Flow-type landslides frequently occur in mountainous areas. To evaluate flow-type landslides, it is essential to identify the physical characteristics of soil, giving focus to the soil on the top layers of various types of slope. This study conducts a survey and an analysis of the characteristics of landslides that occurred in the study area with different geological conditions of granite and gneiss. The characteristics of soil in the area and its surroundings that have or have not undergone landslides for every geological condition is also evaluated. Based on these characteristics and a statistics method, it extracts the triggering factors, permeability coefficients (k), and shearing strength with cohesion (c) and internal friction angel (φ) of soils that are highly related to landslides around weathered soil layers. As a result, the permeability coefficients show significant relevance with void ratio (e), the effective size of grains (D10), and uniformity coefficient (cu), while the shearing strength with the proportion of fine-grained soil (Fines), uniformity coefficient (cu), degree of saturation (S), dry weight density (rd), and void ratio (e). By obtaining this result, the study uses the regression analysis to suggest models to estimate the permeability coefficients and shearing strength. For the gneiss area, the statistics-based estimation model (SEM) is proposed as k_gn = (1.488 × 10^-02 × e) + (1.076 × D₁₀) + (-1.629 × 10^-04 × c_u) - (1.893 × 10^-02) for permeability coefficients; cgn = (-0.712 × Fines) + (-0.131 × c_u) + 15.335 for cohesion; and φgn = (27.01 × r_d) + (-12.594 × e) + 6.018 for internal frictional angle of soils. For the granite area, the statistics-based estimation model (SEM) is proposed as kgr = (8.281 × 10^-03 × e) + (0.639 × D₁₀) + (-2.766 × 10^-05 × c_u) - (9.907 × 10^-03) for permeability coefficients; c_gr = (-0.689 × Fines) + (-0.0744 × S) + 18.59 for cohesion; and φ_gr = (33.640 × r_d) + (-0.875 × e) - 9.685 for internal frictional angle of soils. The use of statistics-based estimation models (SEMs) for landslide-triggering factors that trigger landslides will support the simple calculation of permeability coefficient and shearing strength (cohesion and internal frictional angle), only requiring information about the physical properties of soil at the natural slopes that have different geological features such as gneiss and granite areas.

This study tries to focusing on applying information communication technology for economic importance of Mid Oil Company (MDOC), which is among contemporary oil companies in Iraq. Since ICT forms a significant aspect of achieving organizational economic objectives, most of public and private bodies seek to utilize ICT tool and techniques to improve work efficiencies. The emerging growth in ICT has made it process and service automation possible in managing organizational activities. To determine this effect of ICT on organizations, this study formulated statistical research model at MDOC through using fifteen questionnaires, which were distributed on three axes. The outcome of the questionnaire analysis revealed that there is inadequate comprehensive infrastructure to suitably support ICT within the selected organization management. In addition, it revealed that there are no ideal standards to maintain and sustain internet networks. Based on these revelations, the study presents recommendation for the adoption of ICT with the aim of minimizing cost, enhancing communication and managing infrastructure. Also recommends the need to support IT department within an organization, with essential equipment, in terms of man and machine, for better efficiency to employ the key of ICT Impact in Iraqi governmental oil companies.

The deterioration of soil-cement in corrosive environment leads to the reduction of strength and the increase of permeability. Effective methods of determining deteriorated layer permeability coefficient of soil-cement are currently lacking. A laboratory test method for permeability coefficient of deteriorated layer was proposed using the modified permeability coefficient testing apparatus. According to the proposed method, the permeability coefficient of deteriorated layer can be obtained after testing the permeability coefficient of the soil-cement specimen in curing room and the equivalent permeability coefficient and deterioration depth of the soil-cement specimen in corrosion environment. Taking the marine dredger fill of Jiaozhou Bay for example, the deteriorated layer permeability coefficients of soil-cements with different cement contents were tested. It turned out that the permeability of deteriorated layer increases with the increase of age. At the beginning of curing age, larger cement content leads to smaller permeability coefficient of the deteriorated layer of soil-cement. As the curing age increases, the deteriorated layer permeability coefficient of the soil-cement with larger cement content becomes larger. The evolution of the permeability coefficient of deteriorated layer with age can be formulated as the Logistic function. This study provides a support for anti-permeability designs of soil-cement structures in corrosive environment.

A practical method is presented to estimate rare earth elements (REE) concentrations in magmatic vapour phase (MVP) in equilibrium with water-saturated granitic melts based on empirical fluid-melt partition coefficients of REE (k_P^REE). The values of k_P^REEcan be calculated from a set of new polynomial equations linking to the chlorine molality (m_Cl^v) of the MVP associated with granitic melts, which are established via a statistical analysis on the existing experimental dataset. These equations may be applied to the entire pressure range (0.1 to 10.0 kb) within the continental crust, suggesting that light REEs behave differently in magmatic fluids, i.e. either being fluid compatible with higher m_Cl^v or fluid incompatible with lower m_Cl^v values. In contrast, heavy REEs are exclusively fluid incompatible and partition favourably into granitic melts. Consequently, magmatic fluids tend to be rich in LREE relative to HREE, leading to REE fractionation during the evolution of magmatic hydrothermal systems. Maximum k_P^REEvalue for each element is predicted and presented in a REE distribution diagram constrained by the threshold of m_Cl^v. REE contents of the granitic melt is approximated by whole-rock analysis, so that REE concentrations in the associated MVP would be estimated from the value of k_P^REE given chemical equilibrium retains. Two examples are provided respectively, to show the use of this method as a REE tracer to fingerprint the source of ore-fluids responsible for the Lake George intrusion-related Au-Sb deposit in New Brunswick (Canada), and for the Bakircay Cu-Au (-Mo) porphyry systems in northern Turkey.

The node position information is critical in the wireless sensor network (WSN). However, the existing positioning algorithms commonly have low positioning accuracy because of noise interferences in communication. To solve this problem, this paper presents an iterative positioning model based on distance correction to improve the positioning accuracy of the target node in WSN. First, the log-distance distribution model of received signal strength indication (RSSI) ranging is built and the noise impact factor is derived based on the model. Second, the initial position coordinates of the target node are obtained based on the triangle centroid localization algorithm, thereby calculating the distance deviation coefficient under the influence of noise. Then, the ratio of the distance measured by the log-normal distribution model to the median distance deviation coefficient is taken as the new distance between the anchor node and the target node. Based on the new distance, the triangular centroid positioning algorithm is used again to calculate the target node coordinates. Finally, the iterative positioning model is constructed, and the distance deviation coefficient is updated repeatedly to update the positioning result until the set number of iterations is reached. Experiment results show that the proposed iterative positioning model can improve positioning accuracy effectively.

Inequality of health service for different specialty categories not only occurs in different areas inequality of health service for different specialty categories in the world, but also happens in the online service platform. In the online health community (OHC), health service was often of inequality for different specialty categories, including both online views and medical consultation for offline registered service. Moreover, how the factor city-level impacts the inequality of health service in OHC is still unknown. We designed a causal inference study with data on distributions of serviced patients and online views in over 100 distinct specialty categories on one largest OHC in China. To derive the causal effect of the city-levels (two levels inducing 1 and 0) on the Gini coefficient, we matched the focus cases in cities of rich healthcare resources with the potential control cities. For the Gini coefficient of serviced patients in over 100 specialty categories, the average treatment effect of level-1 cities is 0.470, which is 0.029 higher than that of the matched group. Similarly, for the Gini coefficient of online views, the average treatment effect of Level-1 cities is 0.573, which is 0.016 higher than that of the matched group. For each of the specialty categories, we also estimated the average treatment effect the specialty category’s Gini coefficient ( ) with the balanced covariates. The results support the argument that the total Gini coefficient of all the doctors in OHC shows that the inequality of health service is still very serious. This study contributes to the development of the theoretically grounded understanding of the causal effect of city-level on the inequality of health service in an online to offline healthcare service setting.

A number of experimental and numerical studies point out that incorporating a rotating cylinder can superiorly enhance the aerofoil performance, especially for higher velocity ratios. Yet, there have been less or no studies exploring the effects of lower velocity ratio at a higher Reynolds number. In the present study, we investigated the effects of Moving Surface Boundary-layer Control (MSBC) at lower velocity ratios (i.e. cylinder tangential velocity to free stream velocity) and higher Reynolds number on a symmetric aerofoil (e.g. NACA 0021) and an asymmetric aerofoil (e.g. NACA 23018). In particular, the aerodynamic performance with and without rotating cylinder at the leading edge of the NACA 0021 and NACA 23018 aerofoil was studied on the wind tunnel installed at Aerodynamics Laboratory. The aerofoil section was tested in the low subsonic wind tunnel, and the lift coefficient and the drag coefficient were studied for different angles of attack. The experiments were conducted for two Reynolds numbers: 200000 and 250000 corresponding to two free stream velocities: 20 m/s and 25 m/s, respectively, for six different angle of attacks (-5°, 0°, 5°, 10°, 15° and 20°). This study demonstrates that the incorporation of a leading edge rotating cylinder results in an increase of lift coefficient at lower angle of attacks (maximum around 33%) and delay in stall angle (from 10° to 15°) relative to the aerofoil without rotating cylinder.

Longitudinal dispersion coefficient (LDC) plays an essential role in modeling the transport of pollution and sediment in the natural rivers. As a result of transportation processes, the concentration of pollution changes along the river. Different studies have been conducted to provide simple equations for estimating LDC. In this study, Support Vector Regression (SVR), Gaussian Process Regression (GPR), M5P and Random Forest (RF) examined to predict the LDC in the natural streams. The hydraulic and geometric features of different rivers gathered for developing the mentioned models for LDC estimation and various statistical criteria were utilized to scrutinize of the models. Furthermore, the Taylor chart was used to evaluate the models and achieved results showed that among machine learning models, M5P displayed the superior performance with CC of 0.823, SI of 0.812, NS of 0.577 and WI of 0.879. As well, S-D model with CC of 0.795 SI of 0.827, NS of 0.558 and WI of 0.890 had more precise results than other empirical models. The results indicates that the developed M5P model with simple formulations was superior to other machine learning models and empirical models and therefore, it can be used as a proper tool for estimating LDC in natural rivers.

Although different assessments and evaluations of Dual-Miller cycle performed, specified output power and thermal performance associated with engine determined. Besides, multi objective optimization of thermal efficiency, Ecological Coefficient of performance ( ) and Ecological function ( ) by the mean of NSGA-II technique and thermodynamic analysis performed. The Pareto optimal frontier obtaining the best optimum solution is chosen by fuzzy Bellman-Zadeh, LINMAP, and TOPSIS decision-making techniques. Based on the results, performances of dual-Miller cycles and their optimization are improved.

Immersion in salt-lake solution was adopted to periodically test the concrete chloride-ion diffusion coefficient. The regression analysis was also completed. Also investigated was the time-dependent law of concrete chloride-ion diffusion coefficient with time. The influence of chloride-ion concentration in solution, water-to-cement ratio, and corrosion time on the largeness and accumulation rate of the concrete chloride-ion diffusion coefficient was also analyzed. Test results show that the concrete chloride-ion diffusion coefficient gradually decreased with increasing time and increased with increasing chloride-ion concentration in a salt lake . Taking into account the influence of factors such as water–binder ratio, chloride-ion concentration, and time-varying characteristics, a multi-factor calculation model for the concrete chloride-ion diffusion coefficient was established. Combining the prediction results and the measured data reported in this paper, the effectiveness and applicability of the established concrete chloride-ion diffusion coefficient calculation model were compared and verified, and the durability design and service life of a concrete structure under cool chlorine were compared. The results of analysis provide important boundary conditions.

The diffusion coefficient--a measure of dissipation, and the entropy--a measure of fluctuation are found to be intimately correlated in many physical systems. Unlike the fluctuation dissipation theorem in linear response theory, the correlation is often strongly non-linear. To understand this complex dependence, we consider the classical Brownian diffusion in this work. Under certain rational assumption, i.e. in the bi-component fluid mixture, the mass of the Brownian particle $M$ is far greater than that of the bath molecule $m$, we can adopt the weakly couple limit. Only considering the first-order approximation of the mass ratio $m/M$, we obtain a linear motion equation in the reference frame of the observer as a Brownian particle. Based on this equivalent equation, we get the Hamiltonian at equilibrium. Finally, using canonical ensemble method, we define a new entropy that is similar to the Kolmogorov-Sinai entropy. Further, we present an analytic expression of the relationship between the diffusion coefficient $D$ and the entropy $S$ in the thermal equilibrium, that is to say, $D =\frac{\hbar}{eM} \exp{[S/(k_Bd)]}$, where $d$ is the dimension of the space, $k_B$ the Boltzmann constant, $\hbar $ the reduced Planck constant and $e$ the Euler number. This kind of scaling relation has been well-known and well-tested since the similar one for single component is firstly derived by Rosenfeld with the expansion of volume ratio.

Aim: The aim of the paper is to assess the usefulness of sectoral means in financial analyses of enterprises. Research methods: The article uses an inductive-deductive approach to assess the suitability of sectoral means used in analyses of financial standings of enterprises. The method of analysis and logical construction was used for literature review. The methods of descriptive statistics such as, arithmetic means, standard deviation and coefficient of variation were used in order to analyze the data and draw conclusions based on the results. Contribution: The assessment of the usefulness of sectoral means in the context of their variability seems to be a crucial aspect for the analysis of a company’s financial situation. When assessing the financial standing of an enterprise, it is necessary to use a comparative analysis method, based on, inter alia, a comparison in space. This type of comparison requires the use of sectoral means, whose assessment is extremely important to drawing reliable and correct conclusions of the financial situation of a company.

Human resources are the major input of health systems therefore the equitable distribution of human resources in health care remain critical in making progress towards the goal of universal health coverage and thus to sustainable development. The purpose of this study is to evaluate the health care human resources distribution across regions of Poland between 2010 and 2017 and estimate the level of equity. This research by applying to Polish conditions will allow to fill in the gap in existing literature. Data was derived from the Knowledge Database Health and Health Care of Statistic Poland and Polish Statistical Yearbook. In purpose to examine the distribution of health resources against population size and geographic size in Poland, the Gini coefficient calculated based on the Lorenz Curve was engaged. This study has several major findings. The amount of most types of human resources – as apart from internist, obstetrics and gynecology, occupational medicine - when expressed as number of them per 10,000 population or 1 square km increased in 2017 compared to 2010. Moreover, for most types of health care human resources the level of access slightly changed during analysied period as Gini coefficients decreased. However, the geographical distribution of all types of human resources is less equitable then in case of population distribution. The most troublesome is relatively lower equity in case of oncologist, family medicine and occupational medicine and cardiologist in both population and geographical distribution. Thus this research provides some implications for policy and practice. As the main reason to establish National Health Fund (which meant the centralization of the system) in Poland was to to eliminate regional differences in access to health care, thus this research confirms that still some more corrective actions, in this field, should be undertaken.

Atmospheric correction is a necessary step in image processing data and spectra recorded by spaceborne sensors for pure cloudless atmosphere, primarily in the visible and near-IR spectral range. We have present a fast and sufficiently accurate method of atmospheric correction based on the proposed analytical solutions describing with high accuracy the spectrum of outgoing radiation at the top boundary of the cloudless atmosphere. This technique includes the model of the atmosphere and its optical parameters that are important in terms of radiation transfer. The solution of the inverse problem for finding unknown parameters of the model is carried out by the method of non-linear least squares (Levenberg-Marquardt algorithm) for an individual selected pixel of the image (its spectrum), taking into account the adjacency effects. Using the found parameters of the atmosphere and the average surface albedo, assuming homogeneity of the atmosphere within a certain area of the hyperspectral image (or the whole frame), the spectral albedo at the Earth's surface is calculated for all other pixels. It is essential that the procedure of the numerical simulation with non-linear least squares of the direct transfer problem is based on using analytical solutions, which provides a very short calculation time of the atmospheric parameters (seconds or less) and the ability to perform atmospheric correction "on-fly." Testing methods of atmospheric correction was performed using the synthetic outgoing radiation spectra at the top of the atmosphere (TOA), obtained by numerical simulation in the LibRadTran code, as well as spectra of real space images of the Hyperion hyperspectrometer. A comparison with the results of atmospheric correction in module FLAASH of ENVI package has been performed. Finally, to validate our data obtained by the SHARK method, a comparative analysis with ground-based measurements of Radiometric Calibration Network (RadCalNet) was carried out.

Three-temperature heating systems consist of a heat engine and a heat pump, enabling thus maximum usage of the primary thermal source for the heating of buildings. This analysis has revealed obvious advantages and disadvantages that the combining of thermodynamic systems has in future development, also with respect to environmental and economic issues. It appears that the combination of a Stirling engine or a similar heat drive with a heat pump is especially suitable. In order to analyze the effectiveness of such a system, a comprehensive calculation procedure is used: its basis lies in accounting for all types of energy and their relationship to the original natural resource. The present paper aims to point out that the combination of Stirling engine and a heat pump is a useful solution thanks to the most favorable resultant economic impact if compared to the usage of a diesel, four-stroke gas, or, most commonly used, electric drive.

In this paper, we derive and prove, by means of Binomial theorem and Faulhaber's formula, the following identity between $m$-order polynomials in $T$ $$\sum_{k=1}^{\ell}\sum_{j=0}^m A_{m,j}k^j(T-k)^j=\sum_{k=0}^{m}(-1)^{m-k}U_m(\ell,k)\cdot T^k=T^{2m+1}, \ \ell=T\in\mathbb{N}.$$

This paper focuses on the non-destructive dielectric measurement for low-loss planar materials with a thickness of less than 3 mm using a large coaxial probe with an outer diameter of 48 mm. The aperture probe calibration procedure required only to make a measurement of the half-space air and three offset shorts. The reflection coefficient for the thin material is measured using a Keysight E5071C network analyzer from 0.3 MHz to 650 MHz and then converted to a relative dielectric constant and tangent loss via closed form capacitance model and lift-off calibration process. Measurement error of dielectric constant, Δε_r is less than 2.5 % from 1 MHz to 400 MHz and the resolution of loss tangent, tan δ measurement is capable of achieving 3×10^-3.

Nowadays energy saving is a topical issue due to increasing fuel costs and this aspect is amplified by more stringent emissions regulations that impact on vehicle development. A recent study conducted by the U.S. Department of Energy shows that about five percent of the U.S. energy consumption is transmitted by fluid power equipment. Nevertheless, this study also shows that the efficiency of fluid power averages 21 percent. This offers a huge opportunity to improve the current state-of-the-art of fluid power machines, in particular to improve the energy consumption of current applications. These facts dictate a continuous strive toward improvements and more efficient solutions: to accomplish this objective a strong reduction of hydraulic losses and better control strategies of the hydraulic systems are needed. In fluid power, there exist many techniques to reduce/recover energy losses of the conventional layouts, e.g. load sensing, electrohydraulic flow matching, independent metering, etc. One of the most efficient ways to analyze these different layouts and identify the best hydraulic solution is done through virtual simulations instead of prototyping, since the latter involves higher investment costs to deliver the product into the market. However, to build a fluid power machine virtual model, some problems arise relative to different aspects, for instance: loads on actuators (both linear and rotational) are not constant and pumps are driven by a real engine whose speed depends on required torque. Furthermore, it is important to achieve higher level of detail to simulate each component in the circuit: the greater detail, the better the machine behavior is portrayed, but it obviously entails heavy impact on simulation time and computational resources. Therefore, there is a need to create mathematical model of components and systems with sufficient level of detail to easily acquire all those phenomena necessary to correctly evaluate machine performance and make modifications to the fluid power component design. In this context, a hydraulic proportional valve PVG 32 by Danfoss is taken as an object of study, its performance is analyzed with suitable mathematical model and simulation is done to observe closeness of a model to the laboratory experiment.

Despite a global push in the development and implementation of widespread alternative energy use, significant disparities exist across given nation-states. These disparities reflect both technical and economic factors, as well as the social, political, and ecological gaps between how communities see energy development and national/global policy goals. Known as the “local-national gap,” many nations struggle with fostering meaningful conversations about the role of alternative energy technologies within communities. Mitigation of this problem first requires understanding the distribution of existing alternative energy technologies at the local level of policymaking. Using the State of Georgia, U.S.A. as a case study, we present a model for analyzing how existing adoption trends enable/limit conversation at the scale of local governance (i.e., county governments). Leveraging existing work on the Gini Coefficient as a metric for measuring energy inequity, we argue these tools can be applied to analyze where gaps exist in ongoing solar adoption trends. As we demonstrate, communities that adopt solar tend to be concentrated in a few counties, indicating existing conversations are limited to a circumscribed set of social networks. This information and the model we demonstrate can enable focused qualitative analyses of existing solar trends, not only amongst high-adoption areas but within communities where little to no adoption has occurred.

Gas-liquid reactors pose transfer difficulties due to diffusion effects. It is necessary to master the aeration and hydrodynamics of the medium to conduct the reaction well and get a good performance. For this purpose, a study in a submerged membrane bioreactor with a useful volume of 30L, consisting of a microfiltration membrane with an average pore size of 0.14 mm having an effective surface area of 0.2 m2 and a PVC cylindrical air diffuser of radius 4 cm has been studied. The saline tracing method associated with a conductimetric follow-up made it possible to determine the residence times and the mixing time in the reactor at 4 different points both in recirculation and in the absence of recirculation. Gas retention was measured by the manometric method. The experiments were carried out at different temperatures of 25 ° C, at 45 ° C, with a variable air flow rate of 0.5 to 16 mL / s and different solutions (osmosis water, ammonium formate solution, solution ammonium formate + salt, synthetic rubber effluent). The results show that the mixing time varies from one point to another and the recirculation of the mixture reduces the mixing time. One of the positions is limiting, the transfer is done most by diffusion with a mixing time of 115 min without circulation and 65 min with circulation. Gas retention increases with aeration rate and temperature. On the other hand, the more the medium becomes rich in organic substances, the more the gaseous retention decreases. The homogeneous fine-bubble regime is obtained for an air flow rate of between 3 and 10 mL / s of aeration. Beyond this flow rate, the regime becomes heterogeneous without a transition phase for ammonium formate and formate ammonium + salt solutions.

The unique porous crystal structure of zeolite offers various important utilizations, it is one of the considerations in selecting zeolite at this study as component of composite for restraining noise. It so happens, previous experiments show that banana stem has porous structure, fibrous, high flexibility and can be applied as material for many various products including as component of acoustic material. The combination of both is alleged that it has capability in absorbing noise. This paper presents an investigation on the composite that it was synthesized of Activated Zeolite and Banana Stem Fibre in various weight for determining its sound absorption coefficient alpha (a). Activating natural zeolite was conducted by using 6M HCl in order for enlarging zeolite pores. The sound absorption coefficient was measured in the frequency range between 125 Hz up to 6000 Hz. The results show that the different weight of banana stem fibre as component of the synthesized composite affects the value of alpha and shifts the frequency area.

Free volume is an extremely important intrinsic defect in polymers. Structurally, the free volume is the randomly distributed holes in the polymer molecular chain segments. From the perspective of molecular movement, it is also the space needed for the movement of molecular segments. In proton exchange membrane fuel cells, the free volume is also the space needed for the directional conduction of protons. Irradiation grafting sulfonated polyvinylidene fluoride (PVDF) is one of the methods to produce proton exchange membrane with good proton channel rate. Using the LYS-1 program, based on the linear absorption coefficient and backscatter coefficient models, the percentage of annihilated positrons in PVDF in the two-layer model and the three-layer model was studied, and comparing the two fitting results it is determined that the model closest to the positron annihilation percentage required by the PALS experiment is the two-layer model, which allows the percentage of positrons that are annihilated in PVDF films with a thickness of 100 μm to reach 46% using the high energy positron source ⁴⁴Ti without using the positron moderator. Using positron annihilation lifetime spectrum (PALS) analysis methods, based on Eldrup's classical model of free volume, the influence of absorbed doses of α particles on the free volume and crystallinity of PVDF was investigated, respectively. Based on the two test results the model of cross-linking and degradation of polyvinylidene fluoride irradiated by α particles was determined. Afterwards, X-ray diffraction (XRD) methods was used to study the change of PVDF crystal area before and after irradiation. The XRD results are consistent with the results measured by PALS.

Abstract Due to the relatively low efficiency of thermoelectric (TE) generators, they have mostly been used in niche applications where the unique properties of TE generators outweigh their lack of efficiency, or conditions where it is more reasonable to base the optimal design on maximum generated power rather than maximum efficiency. The aim of this work is to investigate how the different fundamental transport properties (Seebeck coefficient, thermal conductivity and electrical resistivity) in materials with equal figure of merit (ZT) impact TE module design and maximum power output. Further, we discuss and review the strategies to enhance material properties and the latest studies on the TE module performance. It is shown, that by increasing the power factor by a factor of 15 and decreasing the thermal conductivity by 13.33 in order to maintain ZT=1, power output is increased by 45%. This effect is stronger in lower module fill factor and thermal resistance of the heat source and heat sink.

This algorithm is designed to perform Discrete Fourier Transforms (DFT) to convert temporal data into spectral data. This algorithm obtains the Fourier Transforms by studying the Coefficient of Determination of a series of artificial sinusoidal functions with the temporal data, and normalizing the variance data into a high-resolution spectral representation of the time-domain data with a finite sampling rate. What is especially beneficial about this DFT algorithm is that it can produce spectral data at any user-defined resolution.

Water quality monitoring was an important objective in the surroundings. In this study, we investigated the sensing characteristics of the arrayed flexible chloride sensor with XBee wireless sensing system. The sensitivity and linearity of the wireless chloride sensing devices were 91.6 mV/pCl and 0.988, respectively. The hysteresis voltages were 50.14 mV and 36.71 mV during the cycles of 1 M → 10⁻¹ M → 1 M → 10⁻³ M → 1 M and 1 M → 10⁻³ M → 1 M → 10⁻¹ M → 1 M, respectively. The selectivity coefficients of the ClO⁻ ion, ClO₄⁻ ion, NO₃⁻ ion and I⁻ ion for Cl⁻ ion were 5.0 × 10⁻², 1.0 × 10⁻¹, 5.9 × 10⁻³ and 5.6×10⁻¹, respectively. The sensing characteristics of real time measurement were investigated for dynamic microfluidic. The arrayed flexible chloride sensor was integrated with the microfluidic device, syringe pump and wireless sensing system. The sensitivity and linearity were 273.1 mV/pCl and 0.978 at 35 μL/min, respectively.

The transmission of light is one of the key optical processes in the terrestrial environment (the atmosphere and underlying surfaces). The dependence of light transmittance on the illumination/observation conditions and optical properties of the atmosphere–underlying system can be studied using the integro-differential radiative transfer equation. However, for numerous applications a set of analytical equations is needed to describe the transmitted light intensity and flux. In this paper, we describe various analytical techniques to study light transmittance through light scattering and absorbing media. A physical significance and improved mathematical accuracy of approximations are provided using the analytical models for the diffusion exponent, average cosine of the light field, spherical and plane albedos. The accuracy of various approximations is studied using exact radiative transfer calculations with various scattering phase functions, single-scattering albedos, observational conditions, and optical depths.

Soil erosion seriously affects vineyards. In this study, the influence of two plant covers on soil moisture and the effect of different physiographic conditions on runoff and sediment yields were evaluated in a rainfed vineyard formed by four fields (NE Spain) during 15 months. One field had spontaneous vegetation as plant cover and three fields had a cover crop of common sainfoin. The vineyards’ rows were dry and stable, whereas the inter-row areas were wet although very variable, and the corridors were wet and very stable. Soil moisture in the inter-row areas with Common sainfoin was much higher than in the rows (62% - 70%) whereas this difference was lower with spontaneous vegetation (40%). Two runoff and sediment traps (STs) were installed in two ephemeral gullies, and 26 time-integrated surveys (TIS) done. The mean and maximum runoff yields were 9.8 and 30.7 l TIS^–1 in ST2 and 13.5 and 30.2 l TIS^–1 in ST3. The mean turbidity was 333 and 19 g l^–1, and the maximum sediment yields were 41,260 and 2,778 g TIS^–1 in ST2 and ST3. Changes in the canopy covers (grapevines and plant covers) and rainfall parameters explained the runoff and sediment dynamics.

The grain size of CVD (Chemical Vapor Deposition) graphene was controlled by changing the precursor gas flow rates, operation temperature, and chamber pressure. Graphene of average grain sizes of 4.1 µm, 2.2 µm, and 0.5 µm were synthesized in high quality and full coverage. The possibility to tailor the thermoelectric conversion characteristics of graphene has been exhibited by examining the grain size effect on the three elementary thermal and electrical properties of σ, S, and k. Electrical conductivity (σ) and Seebeck coefficients (S) were measured in a vacuum for supported graphene on SiO₂/Si FET (Field Effect Transistor) substrates so that the charge carrier density could be changed by applying a gate voltage (V_G). Mobility (µ) values of 529~1042, 459~745, and 314~490 cm²/V·s for the three grain sizes of 4.1 µm, 2.2 µm, and 0.5 µm, respectively, were obtained from the slopes of the measured σ vs. V_G graphs. The power factor (PF), the electrical portion of the thermoelectric figure of merit (ZT), decreased by about one half as the grain size was decreased, while the thermal conductivity (k) decreased by one quarter for the same grain decrease. Finally, the resulting ZT increased more than two times when the grain size was reduced from 4.1 µm to 0.5 µm.

The present article is dealing with the state of question about building-energy monitoring systems used for data collection to estimate the Heat Lost Coefficient (HLC) with existing methods and so determinate buildings’ Envelope Energy Performance (EEP). In addition, the data requirements of HLC estimation methods are related with commonly used methods for fault detection, calibration and supervision of energy monitoring systems in buildings. Based on an extended review of experimental tests since 1978, a qualitative and quantitative analysis of Monitoring and Controlling System (MCS) specifications has been carried out. Although most actual Buildings Automation Systems (BAS) may measure the required parameters, further research is still needed to ensure that these data are accurate enough to rigorously apply the HLC estimation methods.

Colostrum is a natural product, issued by both mammals and humans in first week of lactation. Among different species, donkey colostrum is considered as having, besides a valuable composition in nutrients and immune factors, an outstanding similitude with human colostrum. In this context, and taking into account the scarcity of available data concerning the interaction between climate factors and colostrum quality, a trial was conducted aiming to identify the possible influence of environmental factors on donkey colostrum nutritional traits. A stock of 16 jennies from 2 farms located in the County of Cluj, during a 7 days postpartum period was analyzed. During experimental period the daily temperature, humidity, and wind velocity data were collected. Strong positive correlations may be reported between fat and lactose, and fat and protein respectively, while moderate to strong correlation is emphasized between lactose and protein content of donkey colostrum. Testing the influence of environmental temperature, relative humidity, and wind velocity influence upon nutritional content of donkey colostrum, results the neglectable influence of the wind velocity, the negative influence of the heat stress upon all studied colostrum components, and complex influence of relative humidity, which has positive influence on fat and lactose increase when it increases, while its increase has negative influence on protein content of donkey colostrum.

In this paper described numerical expansion of natural-valued power function xⁿ, in point x = x_0, where n; x₀ - positive integers. Applying numerical methods, the calculus of nite dierences, particular pattern, that is sequence A287326 in OEIS, which shows the expansion of perfect cube n as row sum over k; 0 ≤ k ≤ n − 1 is generalized, obtained results are applied to show expansion of monomial n^2m+1; m = 0; 1; 2; ..., N. Additionally, relation between Faulhaber's sum ∑_n^m and nite dierences of power are shown in section 4.

The efficiency of cold sheet and strip rolling of steels and non-ferrous metals in the main depends on the quality of the technological lubricant and its cost. In this regard, it is important to develop new compositions of effective metal-working coolants (MWC) having low cost and providing the maximum reduction in the friction coefficient. We developed and tested the new compositions of the MWC on basis of chicken fat, and mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 260 mm during steel 08Kp rolling. The efficiency of the coolants was determined by the factor of metal stretch forming λ and the coefficient of friction μ in the deformation zone which was found by forward slip method. We found the metal-working coolant with 100 % concentration of boric acid esters of mono- and diglycerides is the most effective in steel rolling. Thus the new MWC on basis of boric acid esters of mono- and diglycerides synthesized from the wastes of sunflower oil production can be recommended for use in rolling of structural steels on account of availability, high efficiency, and a low cost.

We have recently solved the tumbling-snake model for concentrated polymer solutions and entangled melts in the presence of both steady-state and transient shear and uniaxial elongational flows, supplemented by a variable link tension coefficient. Here, we provide the transient and stationary solutions of the tumbling-snake model under biaxial elongation both analytically, for small and large elongation rates, and via Brownian dynamics simulations, for the case of planar elongational flow over a wide range of rates, times, and the model parameters. We show that both the steady-state and transient first planar viscosity predictions are similar to their uniaxial counterparts, in accord with recent experimental data. The second planar viscosity seems to behave in all aspects similarly to the shear viscosity, if shear rate is replaced by elongation rate.