The anthropogenic deterioration of aquatic ecosystems affects water resources due to agricultural malpractices, pollution from domestic septic tanks, recreational activities, and poor watershed management, among others. This study examines the management of Las Curias Reservoir (176,974 m2), San Juan, Puerto Rico, post the 2016 arrival of the invasive aquatic fern Salvinia molesta. In December 2019, a community-led initiative introduced the Cyrtobagous salviniae weevil, an effective biological control agent for S. molesta, and commenced a mechanical removal campaign using an aquatic harvester. Limnological sampling (September 2019 to March 2022) and drone flights were employed to measure physicochemical and floating plant cover changes, respectively, in the reservoir. Monitoring of weevils in the reservoir demonstrated a rapid establishment and dispersal, which resulted in visible damage including browning of plants and eventually sinking of entire mats. By January 29, 2021, 71% (125,652 m2) of the reservoir surface was covered by salvinia. In 2022, the reservoir recorded an average dissolved oxygen concentration of 2.38 mg/L -1 (± 0.021, n = 144), the highest in the study period and indicative of ecosystem recovery. After three years of control efforts, dissolved oxygen, pH, and specific conductance returned to levels recorded prior to Salvinia molesta introduction. This ecosystem recovery, a first in Puerto Rico, could be attributed to an early use of mechanical control and a long-term impact of biological control.

Groundwater use for domestic and agricultural purposes is every day in rural communities. However, groundwater quality in those communities is still being determined due to the lack of water quality monitoring programs. The purpose of this study was to evaluate groundwater quality in rural communities using physiochemical parameters. Eight communities using communal boreholes were selected. Water samples were analysed for temperature, pH, electrical conductivity, total dissolved solids (TDS), ammonia, nitrate, and nitrite as Nitrogen. The pH means ranged from 6.6 to 8.1, whereas high TDS levels of 1390 mg/L and 1470 mg/L were observed in two boreholes. Three boreholes had higher electrical conductivity. Two boreholes had elevated nitrate levels of 15 and 21.5 mg/L. The high nitrate level correlates with the pH, EC, and TDS values. Our results suggest that high nitrate levels measured in communities’ boreholes pose ill health to the community, especially children, infants, and elders. Prenatal exposure to high nitrate has been found to have acute health effects in infants. Therefore, there is a need for further longitudinal studies on health risks among vulnerable groups in these communities.

In the Yucatán Peninsula, anthropogenic activities such as urbanization and final dispose of solid and wastewaters critically impact aquatic systems. Here, we evaluated the anthropogenic-related environmental alteration of Lake La Sabana, located in the northern limit of one of the main cities of the Mexican Caribbean. We evaluate lake water quality using physical, chemical, and microbiological indicators, and heavy metals in surficial sediments and fish tissue to evaluate the potential environmental risk. Multivariate analyses reveal that environmental conditions in La Sabana are spatial and temporal heterogeneous. Medium to bad water quality was determined within basins by the NSFWQI, related with the degree of anthropogenic influence. The center-south zones display critical microbiological values largely exceeding national standards. Heavy metals in sediments (Zn>Hg) and fish tissue (Hg) were relatively low, but Hg concentration threat the ecological environment. Incipient wastewater treatment and final dispose in La Sabana is the main responsible of changes in the trophic status and nutrients availability, which in turn may have promoted changes in the biological structure and aquatic plant invasions. Lake La Sabana can be considered a model of the potential sequential effects of the anthropogenic alterations in oligotrophic karts tropical aquatic systems in Yucatán Peninsula.

Abstract: The aim of this study was to evaluate the effects of solids accumulation on greenhouse gas (GHG) emissions, substrate, plant growth and performance of a horizontal flow (HF) treatment wetland (TW) planted with Phragmites australis (Cav.) Trin. ex Steud. sub sp. australis. The study was carried out in an eight-year-old full-scale HF-TW located in the Mediterranean region (Sicily, Italy). To collect data inside the HF unit, nine observation points (besides the inlet and the outlet) along three 8.5 m long transects (T1, T2, and T3) were identified. The first transect (close to the inlet zone) showed hydraulic conductivity (Ks) reduction of about one order of magnitude higher than the other two. Results highlighted GHG emissions increasing during the summer when temperature and solar radiation were higher than in the rest of the year. Carbon dioxide (CO2) emis-sions decreased from T1 to T3, with maximum monthly values in T1 (21.4 g CO2 m-2 d-1) about double with respect to T2 (12.6 g CO2 m-2 d-1) and T3 (10.7 g CO2 m-2 d-1) observed in July. The CO2 seasonal trend was similar to that of P. Australis growth. Theoretical me-thane (CH4) emissions followed the trend of volatile solids (VS), which was about 3.5 and 4 times in T1 to T2 and T3. The highest CH4 emissions in T1 were probably due to anaerobic bacteria (methanogens) that proliferated in the waterlogged, anoxic part of TW. The pore-clogging affected the chemical oxygen demand (COD) removal efficiency which de-creasing from T1 to T3 for the observation period. Notwithstanding this behaviour, the final effluent quality was very satisfactory with the average value of COD removal efficiency above 90%.

Stream chemistry effectively integrates watershed ecosystem processes on both spatial and temporal scales. Streams of coastal areas integrate a more homogeneous, flat topography wherein there can be interactions between the stream and the body of water into which it drains, especially where tidal fluxes occur. The present study assessed water quality of Thompson Bayou, which comes to the campus of the University of West Florida in a wetland after flowing through 4 km of commercial and private property with associated impacts on water quality. Sampling was carried out for one year at eight discrete sites along Thompson Bayou from the UWF campus to the Escambia River. We used a portable field meter to measure temperature, pH, dissolved O2 (DO), and specific conductivity (SC). Except for temperature, all variables exhibited a spatial pattern of significant variation with distance, with consistent increases in DO and SC as the stream approached the river. These variables also exhibited a temporal pattern of significant seasonal variation, including—and especially—temperature. Data suggest that spatial and temporal patterns of water quality of Thompson Bayou are determined by (1) processing of water by the wetland, (2) interactions of the stream channel with upland forest stands, and (3) the tidal hydrology of the Escambia River.

The shrimp industry in the Philippines play a vital role in the local and national economy through exports with markets abroad such as in South Korea, Japan, the USA, and others. This study aimed to describe the various cultural and operational characteristics of small-holder and commercial shrimp farms (P. vannamei) in the Davao region. It also evaluated the current risks and challenges faced by the shrimp farmers. A semi-structured questionnaire that focused on shrimp farmers, and operators in the region was used to collect data with N=41 farmers and operator. The results showed that respondents were engaged in small-holder farming activities which had an average yield of 10 tons/ha. On the other hand, the commercial farms that operate intensively had an average yield of 24 tons/ha. Most small-holder operators used electric generator machines to conduct aeration in their farms using paddlewheels and blowers. For the commercial farms, more paddlewheels and blowers were employed per pond compared to small-holder farms. Generally, the income of a farm was related to the yield of farms or the number of fries rather than social factors or size of farms cultivated. In terms of input costs, feeds were found to have the highest input costs, followed by the fry, fuel, labor, and others (fertilizers and water treatment chemicals). Most of the farmers mentioned that they are affected by diseases such as white spot syndrome (60%), black gills (35%), and red tail (5%). They perceived that the main contamination come from the water source (31%). The main threats mentioned are declining shrimp prices in the market, source of fry, water disposal, and overstocking, and water quality. Based on this study, farmers should follow good shrimp aquaculture practices and there is a need for them to regularly monitor their water quality.

Keenjhar Lake is the main source of drinking water for the metropolitan city of Karachi. The release of untreated wastewater from Kotri industrial area and other sources have made the lake water polluted. This study was subjected to determine the impacts of such pollutant sources on the water quality of Keenjhar Lake. The study involves the analysis of water quality parameters of Keenjhar Lake and its Feeding source (KB Feeder). The sampling sites were selected based on the sources of contamination. The water samples are tested for physical, chemical and microbiological parameters. The result of water analysis indicates the contamination level of the lake is quite alarming for the sites of Kotri effluent and WAPDA colony where Total Dissolved Solids (TDS), Chloride and other ionic metals were quite higher in concentration than other sites. These sites are also contaminated with Fluoride and Arsenic which are carcinogenic elements. The study reveals that the contamination level of feeding source is causing big non-reversible damage to the lake if continued to be uncontrolled. This contamination is mainly due to the release of toxic metals and ions in the KB feeder caused by human carelessness.

The Agricultural Policy/Environmental eXtender (APEX) model is widely used for evaluating agricultural conservation efforts and their effects on soil and water. A key component of APEX application in Korea is simulating water quality impacts of rice paddies because rice agriculture claims the largest cropland area in the country. In this study, a computational module called APEX-Paddy is developed to simulate water quality with considering pertinent paddy management practices such as puddling, flood irrigation management. Data collected at two experimental paddy sites in Korea were used to calibrate and validate the model. Results indicate that APEX-Paddy performs well in predicting runoff discharge rate and nitrogen yield while the original APEX highly overestimates runoff rates and nitrogen yields on large storm events. With APEX-Paddy, simulated and observed flow and mineral nitrogen yield (QN) are found to be highly correlated after calibration (Nash & Sutcliffe Efficiency (NSE) = 0.87 and Percent Bias (PBIAS) = −14.6% for flow; NSE = 0.68 and PBIAS = 2.1% for QN). Consequently, the APEX-Paddy showed a greater accuracy in flow and QN prediction than the original APEX modeling practice using the SCS-CN method.

This study addresses the prediction of recurring failures in water supply networks, a complex and costly task, but essential for the effective maintenance of these vital infrastructures. Using historical failure data provided by Companhia de Água e Esgotos da Paraíba (CAGEPA), the research focuses on predicting the time until the next failure at specific points in the network. The authors divided the failures into two categories: Occurrences of New Faults (ONF) and Recurrences of Faults (RF). To make the predictions, they used predictive models based on Machine Learning, more specifically on MLP (Multi Layer Perceptron) neural networks. The study revealed that, by analyzing data from past failures and considering factors such as altitude, number of failures on the same street and days between failures, it is possible to achieve an accuracy greater than 80% in predicting failures within a 90-day interval. This demonstrates the feasibility of using fault history to predict future water supply outages with significant accuracy. These forecasts allow water utilities to plan and optimize their maintenance, minimizing inconvenience and losses. The article contributes to the field of water infrastructure management by suggesting that the data-driven approach can be applied in other cities or in networks of different types, such as energy or communication networks. The conclusions highlight the importance of data collection and analysis in preventing failures and optimizing water utilities’ resources.

This paper deals with the design, simulation and implementation of shunt hybrid compensator to maintain the power quality in 3-phase distribution networks feeding different types balanced and unbalanced nonlinear loads. The configuration of the compensator consists of a selective harmonic elimination passive filter, a series connected conventional 6-pulse IGBT inverter, acting as the active filter terminated with a dc link capacitor. The theory and modelling of the compensator based on current harmonic components at the load end and their decomposition in d-q axis frame of reference are utilized in the reference current generation algorithm. Accordingly, the source current waveform is made to follow the reference current waveform using a high frequency carrier based controller. Further, this inner current control loop is supported by a slower outer voltage control loop for sustaining desirable dc link voltage. Performance of the compensator is evaluated through MATLAB simulation covering different types of loads and reduction of harmonic currents and THD at the supply side along with excellent regulation of dc link voltage are confirmed. The performance of a hybrid compensator designed and fabricated using the above principles is evaluated and corroborated with the simulation results.

Dental healthcare providers, staff and patients are constantly exposed to the risk of infection or cross-infection in the dental office, particularly due to the formation of biofilms within Dental Unit Waterlines (DUWLs). Good water quality, achieved with environmentally friendly means, is essential in ensuring the safe operation of the clinic. The aim of this study was to evaluate the practices and protocols used in dental offices of Metropolitan Athens in Greece with regards to water quality in DUWLs. The questionnaire about water quality was distributed to dental practitioners in 2022 and was completed by 206 dentists. Water supplied to dental units was mainly from the public network (65.0%), with 55.8% using in-office filtration. Most dentists (71.8%) do not know the active substance of the antiseptic used for the DUWLs, while 96.1% reported having an antiseptic reservoir embedded in the dental unit. Daily flushing with a small and a large amount of fluid was practiced in approximately 83% and 61% of dental offices, respectively. Dental associations should raise awareness regarding water quality and maintenance of DUWLs in dental offices, investing in lifelong learning, while implementing protocols and green strategies.

A discharge mixing zone (DMZ) is a defined geographical area or volume of water in the receiving environment of a discharge where initial dilution of the effluent occurs and where exceedance of water quality criteria may be permitted. DMZs are essential to inform determination of discharge consent conditions and an important element of risk management frameworks to reduce any effects of the discharges on the environment and human health. In this review, we describe the principles and technical application of DMZs. We present an overview of the physical processes that govern the dispersion and dilution of wastewater discharges and the fate of contaminants in coastal environments and define key criteria for determining the size of DMZs. We summarize DMZ requirements in international legislation and guidance and exemplify their application to different types of discharges by means of case studies. The selected case studies illustrate different modelling tools for defining DMZs and different monitoring approaches to assess their effectiveness in achieving ecological and human health objectives.

Three-dimensional (3D) facies and petrophysical models were generated from previously published data of carbonate strata in the Dam Formation (eastern Saudi Arabia) to quantitatively investigate, describe, understand, model, and predict the permeability anisotropy of tidal flat carbonate within a sequence stratigraphic framework. The resulting 3D models were used to conduct fluid flow simulations to demonstrate how permeability anisotropy influences the production of hydrocarbons and ultimately affects decisions concerning future drilling in the exploration and development of carbonate reservoirs that have tidal flat strata. The constructed 3D facies model consists of four lithofacies associations, two of which were grain-dominated associations and two of which were mud-dominated associations. These lithofacies associations varied spatially in four reservoir zones (zones 1 to 4), which represent two fourth-order sequences in the uppermost part of the Dam Formation. Zones 1 and 3 consist of transgressive parasequences, and zones 2 and 4 consist of the regressive parasequences of these sequences. The 3D porosity and permeability models have a coherent match with the distribution of the lithofacies and the stratigraphic framework of the Dam Formation. The results suggested that the permeability anisotropy in zones 1 and 3 is controlled by the occurrence of the grain-dominated lithofacies associated with tidal flat channels. This lithofacies association overlies the sequence boundaries of sequences 1 and 3, forms reservoir bodies with relatively high permeability values, and is elongated perpendicular to the shoreline of the depositional environments. In contrast, permeability anisotropy in zones 2 and 4 is thought to be controlled by the occurrence of the grain-dominated lithofacies associated with the oolitic shoal. This lithofacies association overlies the maximum flooding surface of sequences 2 and 4, forms reservoir bodies with relatively high permeability values, and is elongated parallel to the shoreline of the depositional environments. Fluid flow simulation results suggested that the trend in hydrocarbon production from the constructed 3D models depends on permeability anisotropy in each reservoir zone. Thus, recognizing trends in permeability anisotropy, which might be predicted using sequences stratigraphy, could help to identify potential areas for future drilling.

Abstract: Peptide pools composed of short amino acid sequences have proven to be versatile tools in various research areas and clinical applications. They are powerful tools for epitope mapping, immunotherapy, and vaccine development. Their importance lies in their ability to map complex protein structures, enabling a comprehensive understanding of immune responses and facilitating the identification of potential therapeutic agents. The application of peptide pools also extends to the field of personalized medicine, offering tailored solutions for diseases such as cancer and infectious diseases. Peptide pools are complex mixtures of immunostimulatory antigens primarily intended for T-cell stimulation. They are commercially available in many different compositions and variants. However, unlike other reagents that consist of only one or a few compounds, peptide pools are highly complex products with limited stability. This makes their quality control a major challenge. Quantitative peptide analysis usually requires sophisticated methods, in most cases isotope-labeled standards and reference materials. None of these are routinely available for these products. Synthesis and purification of all labeled peptides might be required. Usually, this approach would be prohibitively laborious and expensive. Therefore, an approach is needed to provide a practical and feasible method for quality control of peptide pools. With insufficient quality control, the use of such products could lead to incorrect experimental results, which would worsen the well-known reproducibility crisis in the biomedical sciences. Here we propose the use of ultra-high performance liquid chromatography (UHPLC) with two detectors, a standard UV detector (at 214 nm) for quantitative analysis and a high-resolution mass spectrometer (HRMS) for identity confirmation. To be cost-efficient and fast, quantification and identification are performed in one chromatographic run. An optimized protocol is shown, and different peak integration methods are compared and discussed. This work was performed using a peptide pool known as CEF, which consists of 32 peptides derived from cytomegalovirus (CMV), Epstein-Barr virus (EBV) and influenza virus, ranging from 8 to 12 amino acids in length.

This paper presented a two-dimensional, well-balanced hydrodynamic and sediment transport model based on the solutions of variable density shallow water equations (VDSWEs) for sediment-laden flows, and the Exner equation for bed changes. Those equations are solved in a coupled way by the first-order Godunov-type finite volume method. The Harten-Lax-van Leer-Contact (HLLC) Riemann solver is extended to find the local Riemann fluxes in order to maintain the exact balance between the momentum term and the bed slope term. The advantage of a well-balanced scheme over an unbalanced scheme is demonstrated by the synthetic standing contact-discontinuity test case. Then, the model is employed to simulate two laboratory experiments. At last, a field case, the 1996 Lake Ha! Ha! flood event (Canada), is simulated. Results of cross sectional geometries and profiles of longitudinal thalweg agree well with measurements. The accuracy and simplicity of the numerical model, together with the robust implementation, make the model a good candidate for practical engineering applications.

The effective integration of aerial remote sensing data and ground multi-source data has always been one of the difficulties of quantitative remote sensing. A new monitoring mode is designed which installs the hyperspectral imager on the UAV and places a buoy spectrometer on the river. Water samples are collected simultaneously to obtain in situ assay data of total phosphorus, total nitrogen, COD, turbidity and chlorophyll during data collection. The cross correlogram spectral matching (CCSM) algorithm is used to match the data of the buoy spectrometer with the UAV spectral data to reduce the UAV data noise significantly. An absorption characteristics recognition algorithm (ACR) is designed to realize a new method for comparing UAV data with laboratory data. This method takes into account the spectral characteristics and the correlation characteristics of test data synchronously. It is concluded that the most accurate water quality parameters can be calculated by using the regression method under five scales after the regression tests of multiple linear regression method (MLR), support vector machine method (SVM) and neural network (NN) method. This new working mode of integrating spectral imager data with point spectrometer data will become a trend in water quality monitoring.

Urban rivers and waterfronts play a vital role in the ecological, social, and economic fabric of cities, providing not only aesthetic value but also serving as important ecosystems that contribute to the overall well-being of urban environments. However, many urban rivers, including the Beirut River in Lebanon, face challenges such as pollution, neglect, and the loss of recreational and ecological value due to urbanization and industrialization. According to the Lebanese MOE (Ministry of Environment), almost 70% of Lebanese rivers are polluted due to untreated waste management systems and which leads to undrinkable water and possible flooding disasters if not treated. This study addresses the problem of abandoned and degraded spaces along the Beirut River riverside through the application of urban acupuncture, a strategic approach that targets specific points in the urban environment to stimulate positive change and regeneration. The aim of the study is to assess the effectiveness of implementing small-scale ‘sensitive urban points’ known as urban acupuncture as the method for regenerating the Beirut River riverside, with the hypothesis that targeted interventions through Blue Urban Acupuncture or Aqua-puncture- can lead to significant improvements in the ecological, social, and economic aspects of the area that re-connect the people of Beirut with its river. The methodology involves a multidisciplinary approach that integrates urban design, and community engagement, and analysing similar examples of different approaches through creating a comparative table. Data collection includes environmental assessments of water quality, biodiversity, and ecosystem health, as well as social surveys to understand community needs and perceptions. By applying urban acupuncture principles to the Beirut River riverside, this study seeks to demonstrate how strategic interventions can lead to the regeneration of abandoned spaces, improve the overall quality of the urban environment, and create sustainable and inclusive riverside landscapes that benefit both the environment and the community.

The phytoplankton community in 66 reservoirs ubicated at the hydrographic basin of the Ebro River (Spain) was analyzed. Samples were collected in the summer season during the period 2010-2015, with the main purpose of evaluate the Trophic State and Ecological Potential according to the Water Framework Directive of the European Union. In this work we presented a representative overview of several consecutive years of the state of the reservoirs and their associated trophic status; methodology was to obtain statistically significant relationships between the phytoplankton community and main physicochemical water quality variables (water transparency, pH, chlorophyll a, total and soluble phosphorus, anoxic zone depth, nitrite, nitrate and ammonium concentrations). We provide data for retrospective comparative of the state of the reservoirs with previous and current studies in order to improve the management of these reservoirs, and to serve as data reference for future works in a context of global change (climate and pollution).

Saudi Arabia consists mainly of desert land. However, it has big and small natural wetlands and artificial wetlands. Most of these wetlands are seen along the Red Sea and the Arabian Gulf coastal regions. Al-Asfar Lake, located in the Eastern Region of Saudi Arabia, is one of the historical landmarks of Al-Ahsa province. The primary lake water source is agricultural drainage water, which some refer to as an artificial lake. This paper mainly aims to reflect shade on the wetlands in Saudi Arabia in general and to show in detail the environmental impacts of Al-Asfar Lake on the ecosystem and biodiversity of the study area. The analytical review of the previous studies conducted in Al-Asfar Lake was adopted in this article. Hence, the impact of the lake on the land-use system, water quality and biodiversity was illustrated as the main outputs of the review analysis. However, the sustainable management of Al-Asfar Lake requires the stakeholders to adopt the wetland ecosystem health concept, which might lead to improving the lake's environmental conditions.

In the context of freshwater ecosystems, turbidity and suspended solids play crucial roles, with their levels significantly influenced by anthropogenic activities. This study focuses on assessing and monitoring these parameters in Albufera de Valencia using Sentinel-2 imagery. The primary aim is to establish reliable estimation algorithms that can contribute to effective ecosystem management. The study calibrated and validated algorithms for estimating turbidity and suspended solids. The R783×R705/R490 model proved to have the best performance for estimating turbidity and total solids in the Albufera. However, R783/R490 obtained a higher coefficient of de-termination for the organic part, while the R705 band was selected for the inorganic part. However, to achieve better estimates of turbidity and inorganic matter, more research is needed in the future. The implications of excessive suspended solids are underscored, including the depletion of dissolved oxygen, and reduced primary productivity due to limited light penetration and habitat availability. Collaboration between disciplines such as limnology, optics and water chemistry are crucial to advance water quality estimation models in lakes and lagoons such as Albufera. By integrating expertise and approaches from these diverse fields, new knowledge can be gained and the basis for more effective management and conservation strategies can be laid.

This research aims to develop an inexpensive ocean observation instrument with a project name is NOBEL (Nusantara Oceanography Backdoor Experiment Laboratory)-BOX. The device can be installed on all types of vessels and placed in a specific area to map the water conditions, providing accurate data for managing a marine area specifically to water quality. The principle of NOBEL-BOX is to attach sensors in a container connected to a microcontroller and then measure directly. The method employed includes experimental design, laboratory and field tests, and data evaluation to produce the necessary system and instruments. The design process involves the construction of the instrument and the fabrication of the device. This process includes creating three-dimensional sketches/drawings, designing microcontrollers and data transmission systems, and power capacity. The sensors attached to this device are surface water temperature, air temperature, salinity, dissolved oxygen, pH, and TDS. The testing phase includes data validation, testing of the device in the laboratory, and field testing. The laboratory and field tests showed that the device worked and provided data that can be used to analyze the seawater condition spatially and over time.

Water quality assessments are crucial for human health and environmental safeguards. The utilization of a subset of artificial intelligence such as Machine Learning (ML) presents significant impacts to enhance the prediction and classification of water quality. In this research, a set of diverse ML algorithms was evaluated to handle a comprehensive dataset of water quality measurements over an extended period. The aim was to develop a robust approach for accurately forecasting water quality. This approach employed machine learning classifiers such as Logistic Regression (LR), Support Vector Machine (SVM), Stochastic Gradient Descent (SGD), K-Nearest Neighbors (KNN), Gaussian Process Classification (GPC), Gaussian Naive Bayes (GNB), Random Forest (RF), Decision Tree (DT), XGBoost, and Multilayer Perceptron (MLP). The water quality parameters assessed for pH, hardness, solids, chloramines, sulfate, conductivity, organic carbon, trihalomethanes and turbidity. The XGBoost model exhibited the highest accuracy of 89.47% among the classifiers and Stacked Ensemble Classifiers (SEC) improved the prediction further to 92.98%. The findings suggest that XGBoost and the SEC hold promise as reliable approaches for water quality assessments in contrast of artificial intelligence.

Despite a growing concern over sustainability in tourism, research on this domain regarding, specifically, lake destinations, is still scarce. Although perceptions on lake destinations have been studied, no study is known that analyses the impact of visitors’ perceptions on satisfaction and behavioral intentions. Thus, this paper aims to develop and test a model to analyse the effect of lake visitors’ perceptions of destination’s sustainability on both satisfaction and loyalty towards lake destinations. A questionnaire survey was conducted in the Shchuchinsk-Burabay resort area, an important lake destination in northern Kazakhstan. The results support the proposed lake destination loyalty model, tested using partial least squares structural equation modelling (PLS-SEM). Sustainability proved to be decisively influential, with water quality being the dimension with the highest impact on satisfaction with the lakes, along with a positive key impact of the absence of congestion. In addition, both water quality and lack of congestion had a significant indirect impact on satisfaction with the lake destination, and on loyalty. Based on the research findings, theoretical conclusions and practical implications are drawn.

A complete halt on all anthropogenic activities and human movement due to COVID-19 lockdown has provided a great opportunity to assess the impact of human activities on coastal marine ecosystems. The current study assessed the concentration of the metals in water samples of the largest brackish water lagoon of Asia; the Chilika lagoon in the state of Odisha, India between pre-COVID-19 and post-COVID-19 lockdown scenarios. Monthly water samples (n=30 stations) from 0.3 m depth were collected from three sectors of the lagoon seasonally; pre-monsoon, monsoon, and post-monsoon. In addition to various physical parameters [pH, salinity, alkalinity, (DO) dissolved oxygen, (TDS) total dissolved solids, and (EC) electrical conductivity] the collected water samples were analysed for 18 trace metals (Al, As, Ba, Be, Cd, Co, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Sr, Th, Tl, U, V). Most of the physical parameters showed a significant variation between pre-and post-COVID-19 scenarios, except for pH and DO. The concentration of five metals (Be, Cd, Co, Ni, and Pb) remained below detection limits in all water samples. The impact of COVID-19 lockdown on the concentration of the metal in the water samples was noticed along with the three sectors of the lagoon. However, eight metals (Al, As, Cr, Fe, Mn, Th, U, and V) were significantly different between the COVID-19 scenarios and the remaining five metals were not statistically significant. The mean concentration of Al, As, Fe, Th, and V were higher in the pre-COVID-19 scenarios, whereas only Cr and Mn were higher in the post-COVID-19 scenarios. The mean concentration of U was similar among both COVID-19 scenarios, even though there were seasonal and sectoral differences. The seasonal influence of riverine influx was more evident on metal concentration during the monsoon season, whereas the difference between sectors was more prominent during the post-monsoon season. An increased number of correlations between physical parameters and metal concentration were observed in the post-monsoon season and post-COVID-19 scenario. This study provides evidence that the imposition of COVID-19 lockdown reduced metal influx in the water column and improved the water quality of the Chilika lagoon. Our results can be used as baseline for metal concentration in surface waters of the lagoon.

Excessive nutrient discharge to tropical island coastlines drives eutrophication and algal blooms with significant implications for reef ecosystem condition and provision of ecosystem services. Management actions to address nutrient pollution in coastal ecosystems include setting water quality standards for discharging surface waters. However, these standards do not account for the effects of groundwater discharge, variability in flow, or dilution, all of which may influence assessment of true nutrient impacts on nearshore reef habitats. We developed a method to estimate dissolved inorganic nitrogen (DIN) loads to coastal zones by integrating commonly available datasets within a geospatial modeling framework for Tutuila, American Samoa. The DIN loading model integrated an open-source water budget model, water sampling results, and publically available streamflow data to predict watershed-scale DIN loading to the island’s entire coastline. When compared to surface water pathways, submarine groundwater discharge (SGD) was determined to be the most important coastal delivery mechanism of terrigenous DIN, which supports findings from other tropical islands. Onsite wastewater disposal systems were also found to be the primary anthropogenic sources DIN to coastal waters. Our island-wide DIN loading model provides a simple and robust metric to define spatially-explicit sources and delivery mechanisms of nutrient pollution to nearshore reef habitats. Understanding the sources and primary transport modes of inorganic nitrogen to nearshore reef ecosystems can have significant implications for place-based management interventions aimed at increasing the adaptive capacity of unique island ecosystems to environmental variation and disturbances.

The semi-enclosed estuary is very susceptible to changes in the physical and environmental characteristics of the inflow from the land and the coastal sea weather and so the continuous and comprehensive monitoring is necessary for managing the estuary. Nevertheless, the standard procedure or schematic framework has not been proposed appropriately to determine how many instruments are necessary and where they need to be deployed to detect critical changes. Therefore, the present work proposes a systematical strategy for the deployments of the monitoring array by using the combination of the graphical optimization with the objective mapping technique. In order to reflect the spatiotemporal characteristics of the bay, the representative variables and eigenvectors are determined by the Empirical Orthogonal Function (EOF), and the cosine angle among them are calculated for a design index of optimization. At the recommended locations, the sampled representative variables are interpolated to reconstruct their spatiotemporal distribution and compared with the distributions of the true values. Analysis confirms that the selected locations, even with a small number of points, can be used for on-site monitoring. Also, the present framework suggests how to determine installable regions for real-time monitoring stations, which reflect the global and local characteristics of the semi-enclosed estuary.

Pit lakes can represent significant liabilities at mine closure. However, pit lakes also present opportunities to provide significant regional benefit and address residual closure risks of both their own and overall project closure, and even offset the environmental costs of mining by creating new end uses. Unfortunately, many pit lakes have continued to be abandoned without repurposing for an end use. We reviewed published pit lake repurposing case studies of abandoned mine pit lakes. We found beneficial end use type and outcome varied dependent upon climate and commodity; but equally important social and political dynamics that manifest as mining company commitments or regulatory requirements. Many end uses have been realized: passive and active recreation, nature conservation, fishery and aquaculture, drinking and industrial water storage, greenhouse carbon fixation, flood protection and waterway remediation, disposal of mine and other waste, mine water treatment and containment, and education and research. Common attributes and reasons that led to successful repurposing of abandoned pit lakes as beneficial end uses are discussed. Recommendations are given for all stages of mine closure planning to prevent pit lake abandonment and to achieve successful pit lake closure with beneficial end uses.

Water, soil/sediment, and 36 fish samples were collected at three major sites along Flint Creek in 2015-2016 and analyzed for total organic carbon (TOC), dissolved organic carbon (DOC), total mercury (tHg), and other water quality indicators. This study was a follow-up to a 2012 study that revealed elevated tHg levels in fish, resulting in a public health advisory. This study revealed tHg concentrations in water below the detection limit (0.0002 ppm); while, tHG in soil/sediment ranged from < 0.0133 ppm to 0.0682 ppm dry weight. No temporal trends existed, but tHG tended to increase with TOC. Mercury levels in sediment were below the threshold effects level suggested as a preliminary screening level by the National Oceanic and Atmospheric Administration (acute = 1.4, chronic = 0.77 ppb). In summary, tHg levels were low; posing little risk to drinking water. Soil/sediment levels were generally higher and could pose risk to aquatic species.

The sustainability of irrigated agriculture depends on the quality of irrigation water used. The electrolyte concentration (EC) of irrigation water may lead to the accumulation of salts in the root zone layers and affect the physiological functions of the crop by osmotic and ion toxicity effects. Further, the cationic and anionic composition of the water may alter the exchangeable cation composition of the soil and as well as its pH. Because of the dominance of sodium salts in many sources of irrigation water, parameters related to sodium such as exchangeable sodium percentage (ESP) of soils and sodium adsorption ratio (SAR) of soil solutions have been commonly used to study the effects of sodium in irrigation water on soil structural stability. Quirk and Schofield concept of ‘threshold electrolyte concentration’ (TEC) has shown the importance of electrolytes in preventing the effects of sodium on soil structure. Based on this concept, several models have been proposed to relate ESP or SAR with EC to predict the possible impacts of irrigation water on soil structural stability. However, many research reports indicate that this relationship varies with soils and a given model is not suitable for all types of soils. Further, the effects of potassium and magnesium in the processes leading to clay dispersion are disregarded in these models. This essay analyses all the factors involved in the structural failure of soils with different cationic composition, identify the defects in these TEC models and re-defines TEC on the basis of new insights on dispersive and flocculating charges of soils. This review does not deal with EC effects on crops and also the role of contaminant ions not involved with soil structural stability.

The Umbulan Water Supply Project is categorized by the Shipping Infrastructure Acceleration Committee in the list of Accelerated National Strategic Projects through Presidential Regulation Number 3 of 2016 concerning the Acceleration of the Implementation of National Strategic Projects, targeted to operate in mid-2019. This is what will be the focus of the stakeholders of the Umbulan Water Supply Project. This study was to identifying and analyzing networks among stakeholders. Method: This study used a qualitative approach with exploratory methods combined with meta-analysis identification design Identification of stakeholder mapping in the context of early detection of stakeholder involvement in the implementation of the Umbulan Water Supply Project at various levels starting from the National, Provincial (East Java), District/City (Pasuruan, Sidoarjo, Surabaya, to Gresik), Sub-District (Winongan, Gondang Wetan, and Pohtjentrek). The conclusion of this study was based on in-depth interviews and focus group discussions in describing the determination of stakeholders which were divided into two, namely primary stakeholder and secondary stakeholder, and outline the result of the indicators analysis on the stakeholder network of Umbulan Water Supply Project.

Elevated indoor CO2 levels might have adverse effects on human health. However, the introduction of outdoor air to lower indoor CO2 concentrations results in significant HVAC energy consumption. Aligning with office hours and the natural light cycle, the utilization of photosynthesis in living walls offers an energy-efficient and sustainable solution for the mitigation of high CO2 levels in office spaces. This study experimentally investigates the impacts of the carbon fixation pathways, light intensity, and substrate moisture content on the CO2 removal rate of living walls at the room scale. Furthermore, the fresh air energy-saving effects of living walls under different scenarios are accurately simulated in EnergyPlus. The results demonstrate that choosing C3 plants over CAM plants in living walls yields higher CO2 removal efficiency. In a 30-m2 office room accommodating 2-3 occupants, living walls can reduce the demand for fresh air by 12.3%-27.8% and decrease fresh air energy consumption by 11.2%-28.2%. The city with the highest energy savings has energy savings that are 4.5 times greater than those of the city with the lowest energy savings. The findings of this research promote the application and development of living walls, thus providing a viable solution for improving indoor air quality.

Based on the engineering background of Daliuta mining area, the fracture distribution and water movement within the weakly cemented overlay strata are studied through liquid-solid coupling physical simulation and COMSOL numerical simulation test. 3D fracture network of overburden strata in mining is plotted based on the result of the physical simulation test. The results showed that the ‘fractured zone’ of the weakly cemented overburden strata in the western area develops more evidently than that in the eastern area ---- wide-opened fractures form at both ends of the working area and this leads to a wide distribution of fractures in the overlying strata.After the initial caving of the roof, height of the penetrating fractures increases rapidly and the separated strata space becomes the main channel for water flow. Under the action of water flow and rock strata movement, mining-induced fractures in overlying rock display cyclic change of expansion, penetration and closure. When the working face is fully mined, the penetrating fractures in the overlying strata and mining-induced fractures up in the working face become the main passages for water flow. The experimental result provides a reference for underground reservoirs layout and maintenance and water-conserved mining in western China.

This research was conducted to analyze the content of Fe, Cu, Cd, Cr, and Pb in several species of fish taken from three lakes that is closely to disposal of industrial waste in Indonesia. The fish samples were taken from three lakes, namely, Muara Angke, Weda, and Morowali. The samples from Morowali were analyzed in April 2019, those from Weda from November to December 2019, and those from Muara Angke in June 2018. All the samples were then analyzed at the chemistry laboratory of the Department of Chemistry, Faculty of Mathematics and Natural Science, University of Indonesia, and the Integrated Laboratory of IPB. The results showed that all types of fish from Morowali and Weda were no longer safe to consume because they contained Fe, Cu, Cd, and Cr exceeding the threshold of metal contamination. Meanwhile, all types of fish from Muara Angke, except for ayam-ayam, are still safe for consumption. The results of this study can be a source of information regarding metal content in fish and fish feed for safe consumption. Several studies have been done to determine the metal pollutants contained by fish. Given the high consumption rate of fish and the hazards of heavy metals on humans’ health, such research must be furthered

Paving blocks are concrete pieces placed in exposed places to the weather, which are sub-jected to loads and wear. Hence, quality control in the manufacture of paving blocks is es-sential to guarantee the properties and durability of the product in construction projects. In Ecuador, the requirements are described in the Ecuadorian technical standard "NTE INEN 3040", and tensile splitting strength is a fundamental requirement to guarantee product quality. It is analyzed using quality control measurements such as dimensions, the weight of the fresh paving block in the vibro-compacted process, and the percentage of water absorption in order to know how the variables influence and manage to predict the tensile splitting strength to avoid product non-conformity in advance, having a timely and better control of the manufacturing process. The data was obtained from a company that can produce 30 000 units per day of rectangular paving blocks with 6 cm thickness. Mul-tivariate models such as multiple linear regression, regression trees, random forests and neural networks are performed to predict the tensile splitting strength variable through two groups of predictors; the first group is the thickness mm, width mm, length mm, mass of fresh paving block g and percentage of water absorption %. The second group of pre-dictor variables is the density of the fresh paving block kg/m3 and the percentage of water absorption %. It is concluded that the multiple linear regression method performs better in predicting the first group of predictor variables with a mean square error (MSE) of 0.110086, followed by the neural network without hidden layers resulting in an MSE of 0.112198. The best method for the second set of predictors was the neural network with-out hidden layers with a mean square error ( MSE ) of 0.112402, closely followed by the multiple linear regression model with an MSE of 0.115044.

Quality of Service (QoS) metrics deal with network quantities, e.g. latency and loss, whereas Quality of Experience (QoE) provides a proxy metric for end-user experience. Many papers in the literature have proposed mappings between various QoS metrics and QoE. This paper goes further in providing analysis for QoE versus bandwidth cost. We measure QoE using the widely accepted Mean Opinion Score (MOS) rating. Our results naturally show that increasing bandwidth increases MOS. However, we extend this understanding by providing analysis for internet access scenarios, using TCP, and varying the number of TCP sources multiplexed together. For these target scenarios our analysis indicates what MOS increase you get by further expenditure on bandwidth. We anticipate that this will be of considerable value to commercial organizations responsible for bandwidth purchase and allocation.

In the pursuit of energy efficiency and reduced environmental impact, adequate ventilation in enclosed spaces is essential. This study presents a hybrid neural network model designed for real-time monitoring and prediction of environmental variables. The system comprises two phases: An IoT hardware-software platform for data acquisition and decision-making, and a hybrid model combining short-term memory and convolutional recurrent structures. The results are promising and hold potential for integration into parallel processing AI architectures.

In recent decades, as eutrophication in inland and coastal waters (ICWs) has increased due to anthropogenic activities and global warming, so has the need for timely monitoring. Compared with traditional sampling and laboratory analysis methods, satellite remote sensing technology can provide macro-scale, low-cost, and near real-time water quality monitoring services. The Geostationary Ocean Color Imager (GOCI), integrated onboard the Communication Ocean and Meteorological Satellite (COMS) from the Republic of Korea, was the first geostationary ocean color observation satellite and was operational from April 1, 2011 to March 31, 2021. Over ten years, GOCI has observed oceans, coastal waters, and inland waters within its 2,500 km×2,500 km target area centered on the Korean Peninsula. The most attractive feature of GOCI, compared with other commonly used watercolor sensors, was its high temporal resolution (1h, eight times daily from 0 UTC to 7 UTC), providing the opportunity to monitor the quality of ICWs, where optical properties can change rapidly throughout the day. This systematic review aims to comprehensively review GOCI features and applications in ICWs, analyzing progress in atmospheric correction algorithms and water quality monitoring. Analyzing 123 articles from the Web of Science and China National Knowledge Infrastructure (CNKI) through a bibliometric quantitative approach, we examined GOCI’s strength and performance with different processing methods. These articles reveal that GOCI played an essential role in monitoring the ecological health of ICWs in its observation area in East Asia. GOCI has led the way to a new era of geostationary ocean satellites, providing new technical means for monitoring water quality in oceans, coastal zones, and inland lakes. We also discuss the challenges encountered by geostationary satellites in monitoring water quality and provide suggestions for improvements.

Environmental monitoring programs rely on periodic spot sampling at specific locations, followed by laboratory analysis, aiming at the evaluation of water quality at a catchment scale. For this purpose, automatic telemetric stations for specific parameters have been installed by the Institute of Marine Biological Resources and Inland Waters of Hellenic Centre for Marine Research (IMBRIW-HCMR) within several Greek rivers and lakes, providing continuous and temporal monitoring possibilities. Nevertheless, the employment of unmanned surface vehicles (USV) equipped with integrated sensors represents a tool valuable to several monitoring strategies, offering enhanced temporal and spatial coverage over specific timeframes, allowing for targeted examination of sites or events of interest. The USVs have been deployed by Athens Water and Sewerage Company (EYDAP) as a cost-effective tool for the environmental monitoring of surface water bodies of interest, with emphasis on the spatial fluctuations of chlorophyllα, electrical conductivity, dissolved oxygen and pH, observed in Koumoundourou Lake and rivers Acheloos, Asopos and Kifissos. The effectiveness of an innovative heavy metal (HM) system installed in the USV for thein situ determination of copper and lead was also evaluated herewith. The results obtained demonstrate that both the timely detection of potential pollution from both anthropogenic activities and natural processes as well as the monitoring of inland waters are made feasible through the employment of USV.

Food and nutrition insecurity, affecting 30% of the global population in 2020, poses a significant challenge to achieving Sustainable Development Goal (SDG) 2 - Zero Hunger. Urbanization, particularly in sub-Saharan African cities e.g. Lagos, Nigeria, exacerbates these issues, impacting resources and contributing to informal settlements. There is emphasis on innovative solutions in urban farming, with Recirculating Aquaculture Systems (RAS) emerging as one of the promising approach due to its efficiency in space and capital utilization. However, maintaining optimal conditions in RAS, crucial for SDG 2 and 11, requires robust water quality monitoring. This study explores the availability of digital tools for water quality monitoring in small-scale urban RAS, evaluating handheld devices and IoT sensors' reliability through t-test statistical method. The results aim to guide practitioners in selecting effective monitoring tools, contributing valuable insights for sustainable aquaculture in urban areas, particularly in sub-Saharan Africa, where access to affordable digital solutions is pivotal for success and can attract youth to agri-food technologies.

Abstract: The species composition, the structure of phytoplankton communities, hydrochemical parameters in the artificial cooling reservoir of one of the largest thermal power plants (TPP) in the north-east of Europe in the Pechora River basin, Komi Republic were studied in the ice-open period in June and August. Altogether 81 species of algae and cyanobacteria was revealed with the last one predominated. Among cyanobacteria and algae (Bacillariophyta, Chlorophyta), indicators of water quality were found. Assessment of water quality according to the species composition and abundance of indicator phytoplankton species showed that the waters of the Pechorskoe Reservoir can be at-tributed to the III class of water quality, beta-mesosaprobic self-purification zone, with water quality of satisfactory purity, retaining the ability to self-purify. An increase in the diversity of plankton communities and high values of their abundance and biomass under the influence of the warming effect of TPP water outlet were noted and revealed its spatial distribution over the reservoir surface. The plankton of the northern reservoir under the influence of warm waters indicates a slight in-crease in the trophic status of the studied water body, which is also confirmed by the data of hydrochemical analysis. Ecological mapping for the chemical and biological variables as well as pollution indices over the water area of the reservoir was carried out. The results obtained can be used to make forecasts of changes in the phototrophic biota of small northern water bodies under the conditions of climate change.

The Yamuna River in Delhi is a prevalent epitome of the depleted ecosystem that has transformed into a sewage drain due to intense pollution and blooming anthropogenic pressure. As a leading polluter, Delhi contributes to more than 70% of Yamuna's pollution load. Its drains discharge a massive B.O.D. load daily into the river, making it severely polluted, as reflected by the water quality index. The paper uses secondary data to analyze the parameters to determine the water quality of Yamuna at different monitoring sites. It performs correlation analysis to determine the relationship among factors contributing to river water pollution. The results of correlation analysis suggest a highly significant association between parameters COD-BOD, but the association is mild to a minimum among other parameters such as BOD-DO, BOD-pH, COD-DO, COD-pH and DO-pH. Most parameters were observed to be above the hazardous level acceptable for using river water. The analysis of S.T.P.s indicates the need to increase the capacity in terms of treatment, storage, reopening of closed plants and efficient operation to meet the increasing demand for fresh Water. Also, there is a need to create demand for wastewater in different sectors of urban areas like construction, horticulture, industrial coolants, etc.

Coastal marine ecosystems worldwide, like Florida Bay, are increasingly affected by tide alteration and anthropogenic disturbances which affect water quality imbalance leading to algal blooms. Increased bloom persistence is a serious threat due to the long-lasting impact on processes like carbon cycle and services like species presence. However, exploring eco-environmental feedback patterns of algal blooms remains challenging and poorly investigated, also due to the paucity of data. Florida Bay, taken as an epitome, has long experienced algal blooms in its central and western regions, and in 2006 an unprecedented bloom occurred in the eastern habitats. We analyzed the occurrence of blooms from three perspectives: (1) the spatial spreading networks of chlorophyll-a (CHLa) that pinpoints source and unbalanced habitats; (2) the fluctuations of water quality factors pre- and post-bloom outbreaks to in assess environmental impacts of ecological dysbiosis and target prevention and control of algal of blooms; and (3) the biogeochemical-spreading network topological co-evolution to quantify ecosystemic stability and ecological shift likelihood in long-term. Here, we propose Transfer Entropy (TE) to quantify dynamical interactions between spatial areas and biogeochemical factors (ecosystem connectome) underpinning bloom emergence and spreading, as well as environmental effects; the Pareto principle is defined for identifying the salient eco-environmental interactions of CHLa. We quantified the spatial dynamics of algal blooms, and thus obtained areas in need for ecological monitoring and potential bloom control. Results show that algal blooms are increasingly persistent over space with long-term negative effects on water quality factor. A dichotomy is reported between spatial ecological corridors of spreading and biogeochemical networks as well as divergence from the optimal eco-organization: randomization of the former due to nutrients' overload and temperature increase leads to scale-free CHLa spreading and extreme outbreaks a posteriori. Subsequently this increases bloom persistence, turbidity and salinity with potentially strong ecological effects on highly biodiverse and vulnerable areas such as tidal flats and marshes. Algal blooms are important ecosystem regulators of nutrient cycles; however, beyond limit chlorophyll-a outbreaks cause aquatic species mortality due to their effect on water turbidity, nutrient balance (nitrogen and phosphorus in particular), salinity and temperature. Beyond compromising local environmental quality, socio-ecological services are also compromised at large scales, yet ecological assessment models like the one presented are in need of application in subtropical and tropical bays worldwide.

Drought and high temperature often occur simultaneously will eventually affect rice (Oryza sativa L.) yield and seed quality. The objective of the study was to compare the effects of high temperature (HT) and water limitation (WL) during seed development and maturation on yield component, seed quality, and amylose content in aerobic rice cv. MRIA. Two experiments were conducted concurrently in greenhouse with ⁓35/26℃ subjected to elevated HT and/or WL; 5 days 38/28°C at 10, 15, 29 DAA and/or HT; 7 days at 40/28℃ at 8 and 21 DAA with 12h photoperiod in control environment growth chamber. Both experiments were respectively harvested at physiological maturity of 31 and 35 DAA. Grain yielded from the irrigated plant declined from over 27% to below 18% between 15 and 29 DAA. Combination stresses resulted in greater reduction of grain yield than single stress. Late seed development (29 DAA) had no effect either on yield component or seed quality as well as produce a high concentration in amylase content (16.7%) with greater germination capacity (91%). The non-stress plant harvested at 21 DAA resulted the highest percentage of germinated seeds (97%) whereas the vigour index (VI) was reduced to 70.3% and 58.9% at 8 and 21 DAA respectively. Extended plant stress to 7 consecutive days incurred the highest VI with low concentration of amylose content. There was a linear relationship incurred between seed amylase content with germination capacity and VI, however, there was an inverse relationship (R2 = 0.19) between amylase content with VI from plant treated with (HT and/or WL) for 7 days. The present results confirmed that the avoidance HT and WL during early (10 DAA) and mid (15 DAA) seed development with short duration of stress (5 days) obtained better in yield component, enhanced the seed quality and amylose concentration. The combined HT and WL damaged seeds’ quality were more than each stress alone. Therefore, avoiding HT and WL can be practically applied by farmers by irrigating throughout the rice plant during histodifferentiation to save water usage during seed maturation.

This paper investigated the effectiveness of natural wetlands (Phragmites australis) along Wadi Zomer in reducing the organic and inorganic pollution loads from diverse industrial discharges including occasional emergency discharges from Nablus West Sewage Treatment Plant (NWSTP), Palestine. We monitored physical and chemical parameters at four selective sampling stations (S1-S4) along Wadi Zomer with a length of 5 km downstream of NWSTP to assess the purification capacity of Wadi Zomer treatment wetlands (water, sediment, and vegetation) with Phragmites australis in pollution loads reduction. The results showed that S2 (0+0.5 km) and S3 (0+3.0 km) reflected an increase in pollution loads due to illicit industrial discharge and sewer overflow discharge from NWSTP during emergency conditions. BOD values varied significantly along the sampling sites from 6.64 mg/l (S1) to 437.10 mg/l (S3). The BOD at S1 and S2 in water samples were below the Palestinian Water Standard (PWS) compared to S3 and S4 with 437.1 and 333.9 mg/l, respectively. Water samples from all sites (S1-S4) showed a decreasing tendency in heavy metals concentrations (Fe>Cu>Zn>Cr >Ni) and were below the PWS limits, sediment samples followed the same decrease pattern for Zn, Cr, and Ni content with Wadi Zomer flow course. The concentration of Fe (6687 mg/kg) and Cu (1384.7 mg/kg) were highest in the sediment samples (S1-S4); this might be due to non-point sources of pollution. The research demonstrated that phytoremediation is a sustainable nature-based technology for the restoration of heavily polluted surface water bodies in Palestine.

Water quality retrieval for small urban waterbodies by remote sensing get used to be difficult due to coarse spatial resolution of the remote sensing imagery. The recently launched Sentinel-2 produces imagery with a spatial resolution of 10 m. It provides an opportunity to solve the problem of retrieving water quality for small waterbodies. Additionally, many water management issues also require fine resolution of imagery, e.g. illegal discharge to an urban waterbody. Since illegal discharges are an important issue for urban water management, chemical oxygen demand (COD), total phosphorous (TP), and total nitrogen (TN) were chosen as the target parameters for water quality retrieval in this study. COD, TP and TN, however, are non-optically active parameters. There were limited studies in the past to retrieve these parameters in comparison with optically active parameters, e.g. Chlorophyll-A etc. This study compared three machine learning models, namely Random Forest (RF), Support Vector Regression (SVR), and Neural Networks (NN), to investigate the opportunity to retrieve the above non-optically active parameters. Results showed that R² of TP, TN, and COD by NN, RF and SVR were 0.94, 0.88, and 0.86, respectively. The performances of water quality retrieval for these non-optically active parameters were significantly improved by the optimized machine learning models. These models hence solved the problem to use remote sensing data to retrieve these non-optically active water quality parameters and provided a new monitoring strategy for small waterbodies. Water quality mapping obtained by Sentinel-2 imagery provided a full spatial coverage of the water quality characterization for the entire water surface. Compared with water samples collecting and testing, it greatly reduced labor cost, reagents cost, and waste treatment cost. It also may help identify illegal discharges to urban waterbodies. The method developed in this research provides a new practical and efficient water quality monitoring strategy in managing water with consideration of environmental sustainability.

This study used double-bounded dichotomous-choice to estimate and analyze the factors affecting households’ willingness to pay (WTP) for water quality improvement. This study notes that households with higher income, living near polluted water source, using tap water instead of natural water, who are handicraft producers, and who have more members are willing to pay more. However, households who rarely hear about environmental pollution issues and who are offered a higher bid are more likely to refuse to pay. Solutions to improve water quality are suggested such as to raise people's awareness through communication channels and social organizations; to increase income associated with environmental protection policies; to construct wastewater treatment plants; to encourage the relocation of production establishments to industrial parks and industrial complexes; to put regulations on collection, payment and sanctions in case of not declaring and paying fees into village conventions; to promulgate circulars, and bylaws to concretize and simplify regulations and policies of the Government, Ministry of Natural Resources and Environment.

Unmanned Aerial Vehicles (UAVs) have gained significant attention in recent times due to their suitability to a wide variety of civil, military and societal missions. Development of an unmanned amphibious vehicle integrating the features of a multi-rotor UAV and a hovercraft is focus of the present study. Components and subsystems of the amphibious vehicle are developed with due consideration on aerodynamic, structural and environmental aspects. Finite element analysis (FEA) on static thrust conditions and skirt pressure are performed to evaluate the strength of structure. For diverse wind conditions and angles of attack (AOA), computational fluid dynamic (CFD) analysis is carried out to assess the effect of drag and suitable design modification is suggested. A prototype is built with a 7 kg payload capacity and successfully tested for stable operations in flight and water-borne modes. Internet of Things (IoT) based water quality measurement is performed in a typical lake and water quality is measured using pH, dissolved oxygen (DO), turbidity and electrical conductivity (EC) sensors. The developed vehicle is expected to meet functional requirements of disaster missions catering to the water quality monitoring of large water bodies.

The goods and services produced by forest vegetation ecosystem are the driving force for the rapid, high-quality and sustainable development of human society. In history, with the increase of population and economic development, there is an increasing demand for the quantity and variety of forest vegetation ecosystem products and services in a country or a region. To meet the demands, most of the original forest has become farmland, plantation and grass and crops land. As a result, the plant water relationship changed from equilibrium to non-equilibrium, which easily led to soil drought, soil degradation and vegetation decline in dry years or waste of soil water in rainy years in most of water-limited regions. In order to solve the question and realize the sustainable utilization of soil water resources and the high-quality sustainable development of forest, it is necessary to apply the limit theory of plant utilization of soil water resources and the vegetation carrying capacity theory in the critical period of plant-water relationship regulation to adjust the relationship between plant growth and soil moisture to obtain the maximum yield and benefit and realize high-quality and sustainable development.

Iron, a crucial element in our environment, plays a vital role in numerous natural processes. Understanding the presence and concentration of iron in the environment is very important, as it impacts various aspects of our planet’s health. On-site detection and speciation of iron are significant for several reasons. In this context, the present work aims to evaluate the applicability of voltammetry for on-site determination of iron and its possible speciation using a portable voltammetric analyzer. Voltammetry offers the advantage of convenience and cost-effectiveness. For iron (III) determination a modification of a glassy carbon electrode (GCE) with an antimony-bismuth film (SbBiFE) using acetate buffer (pH=4) as supporting electrolyte was used. The technique adopted was Square Wave Adsoptive Cathodic Stripping Voltammetry (SW-AdCSV) and we used 1-(2-piridylazo)-2-naphthol (PAN) as iron (III) ligand. Linearity, repeatability, detection limit and accuracy were determined using synthetic solutions, then a Standard Reference Material (SRM) 1643f - Trace Elements in Water was used for validation measurements in real matrix. The procedure was finally applied to real samples (tap, lake and sea water) and the results obtained were compared by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). The results obtained demonstrated the excellent applicability of the proposed on-site voltammetric procedure for the determination of iron and its speciation in water.

In Mexico, the evaluations of environmental flows are regulated by the Mexican Norm NMX-AA-159-SCFI-2012 and they warrant the establishment of water reserves for the environment. Yet, the pressure for water use limits the establishment of said reserves. This research aimed to evaluate the changes through time of the variables that serve as a basis for the implementation strategy by the Mexican government. A geographical information system was built with updated variables, the desired conservation status was analyzed, and the potential reserves were estimated based on the reference values for all basins nationwide. The results were examined according to their historical, current, and potential contribution to the conservation of natural protected areas and their connectivity. The outcomes point towards an administrative implementation strategy with positive outcomes despite the growing pressure for water use, with a change rate higher than the one for the creation of new protected areas. Currently, basins with low pressure and high conservation value have the potential to contribute to 86–88% of the goal set by the present administration without affecting water availability. Finally, reserving water in the priority basins would guarantee the legal protection of the flow regime in 48–50% of the hydrographic network in a desired conservation status, 45–49% of wetlands of international importance, and other natural protected areas in 85–89% of the global ecoregions represented in Mexico.

Water management can improve the quality of valuable ecosystem services but can be costly to implement and the management costs are covered by national taxes collected by water users. Based on 30 valuation studies of water quality improvement from the Environmental Valuation Information System (EVIS) database provided by Korea Environment Institute (KEI), a meta-regression analysis was employed to measure the benefits that major river basins provided to the society. We compare these benefits to the costs, namely River Management Funds (RMFs) which are financial resources to support a variety of projects for managing and improving upstream water quality. Based on benefit-cost comparison, this study evaluates the efficiency of water resource management in South Korea. This study also provides policy options that are helpful to maintain the sustainability of water resource by improving the planning and performance of water management in the long run.

Legionnaires’ disease is normally acquired by inhalation of legionellae from a contaminated environmental source. Water systems of large buildings, such as hospitals, are often contaminated with legionellae and therefore represent a potential risk for the hospital population. In this study, we demonstrated the constant presence of Legionella in water samples from the water system of a large university hospital in Messina (Sicily, Italy) consisting of 11 separate pavilions during a period of 15 years (2004-2018). In total, 1346 hot water samples were collected between January 2004 and December 2018. During this period, to recover Legionella spp. from water samples the standard procedures reported by the Italian Guidelines emanated in 2000 were adopted; from May 2015 to 2018 Italian Guidelines revised in 2015 (ISS, 2015), were used. The most water samples (72%) were positive to L. pneumophila serogroups 2-14 whereas L. pneumophila serogroup 1 accounted for the 18% and Legionella spp. for the 15%. Most of the positive samples were found in the buildings where are situated critical wards as ICU, Neurosurgery, Surgeries, Pneumology and Neonatal Intensive Unit Care. We highlighted the importance of a continuous monitoring of hospital water samples to prevent the potential risk of nosocomial legionellosis.

The success of source protection in ensuring safe drinking water is centered around being able to understand the hazards present in the catchment then plan and implement control measures to manage water quality risk to levels which can be controlled through downstream barriers. The programs in place to manage source protection are complex sociotechnical systems involving policy, standards, regulators, technology, human factors and so on. This study uses System Theoretic Process Analysis (STPA) to analyze the operational hazards of a typical drinking water source protection (DWSP) program and identify control measures to ensure safe operations. To validate the results a questionnaire was developed and distributed to specialists in DWSP in Taiwan, Australia and Greece. Using Principle Components Analysis (PCA) of the questionnaire responses, the study identified four critical success factors (CSFs) for DWSP. The four factors identified are ‘Policy and Government Agency Support of Source Protection’, ‘Catchment Risk Monitoring and Information’, ‘Support of Operational Field Activities’ and ‘Response to Water Quality Threats’. The results of this study provide insight into the approach of grouping of source protection measures to identify a series of targeted CSF for operational source protection programs. Using CSF can aide catchment management agencies in ensuring that the risk level in the catchment is managed effectively and that threats to public health from drinking water are managed appropriately.

The RMA11 water quality model, which has been previously calibrated and validated, was coupled with the RMA10 3D hydrodynamic model to evaluate sanitation scenarios in Buenaventura Bay. The bay receives direct discharge of untreated wastewater from 500,000 people through 695 outlets along the coast. Five different effluent reduction scenarios were proposed and compared based on fecal coliform concentration as an indicator. The areas where values exceed the standard for primary contact were also used to evaluate the scenarios. The model results indicate poor water quality in the bay and how that the situation will become even more severe if immediate action is not taken. The proposed reduction in discharges in stages will have temporarily more severe effects than the current situation, but these will end when the treatment plant becomes operational. However, even with the plant in operation, complete sanitation of the bay cannot be achieved, and further measures must be considered.

The monitoring of surface-water quality followed by water-quality modeling and analysis is essential for generating effective strategies in water-resource management. However, worldwide, particularly in developing countries, water-quality studies are limited due to the lack of a complete and reliable dataset of surface-water-quality variables. In this context, several statistical and machine-learning models were assessed for imputing water-quality data at six monitoring stations located in the Santa Lucía Chico river (Uruguay), a mixed lotic and lentic river system. The challenge of this study is represented by the high percentage of missing data (between 50% and 70%) and the high temporal and spatial variability that characterizes the water-quality variables. The competing algorithms implemented belonged to both univariate and multivariate imputation methods (inverse distance weighting (IDW), Random Forest Regressor (RFR), Ridge (R), Bayesian Ridge (BR), AdaBoost (AB), Hubber Regressor (HR), Support Vector Regressor (SVR), and K-nearest neighbors Regressor (KNNR)). According to the results, more than 76% of the imputation outcomes are considered satisfactory (NSE > 0.45). The imputation performance shows better results at the monitoring stations located inside the reservoir than the ones positioned along the mainstream. IDW was the most chosen model for data imputation.

Riparian restoration is an important objective for landscape managers seeking to redress the widespread degradation of riparian areas and the ecosystem services they provide. This study investigated the long-term outcomes of ‘one-off’ restoration activities undertaken in the Upper Murrumbidgee Catchment, NSW, Australia. The objective of the restoration was to protect and enhance riparian vegetation and control erosion, and consequently reduce sediment and nutrient delivery into the Murrumbidgee River. To evaluate the outcomes 10 years after restoration, rapid riparian vegetation and geomorphological assessments were undertaken at 29 sites spanning the four different restoration methods used (at least five replicates per treatment), as well as at nine comparable untreated sites. We also trialed the use of aerial imagery to compare width of riparian canopy vegetation and projective foliage cover prior to restoration with that observed after 10 years. Aerial imagery demonstrated the width of riparian canopy vegetation and projective foliage cover increased in all restored sites, especially those with native plantings. The rapid assessment process indicated that 10 years after riparian restoration, the riparian vegetation was in a better condition at treated sites compared to untreated sites. Width of riparian canopy vegetation, native mid-storey cover, native canopy cover and seedling recruitment were significantly greater in treated sites compared to untreated sites. Geomorphological condition of treated sites was significantly better than untreated sites, demonstrating the importance of livestock exclusion to improve bank and channel condition. Our findings illustrate the value of ‘one-off’ restoration activities in achieving long-term benefits for riparian health. We have demonstrated that rapid assessments of the vegetation and geomorphological condition can be undertaken post-hoc to determine the long-term outcomes, especially when supported with analysis of historical aerial imagery.

This study reports multivariate statistical techniques applied including cluster analysis to evaluate and classify the river pollution level in Taiwan, and principal component analysis-multiple linear regression (PCA-MLR) to identify the possible pollution source. Water quality and heavy metal monitoring data from Taiwan Environmental Protection Administration (EPA) was evaluated for 14 rivers in the four regions of Taiwan. The Erren River was classified as the most polluted River in Taiwan. Biochemical oxygen demand, ammonia, and total phosphate concentration in this river were the highest of the 14 rivers evaluated. In addition, heavy metal levels of the following rivers exceeded the Taiwan EPA standard limit: lead - in the Dongshan, Jhuoshuei, and Xinhuwei Rivers; copper - in the Dahan, Laojie, and Erren Rivers; and manganese - in all rivers. Water pollution in the Erren River was estimated to originate 72% from industrial sources, 16% from domestic black water, and 12% from natural sources and runoff from other tributaries. Our research showed that PCA-MLR and the cluster analysis model accomplished our study objectives and will be helpful tools to evaluate water quality in rivers and we suggest that the continuous monitoring should be conducted to monitor water pollution from anthropogenic activities.

Lake Chapala is a natural ecosystem of Mexico, declared Ramsar site, currently, is an area with importance in the agricultural sector, tourism, and important source of drinking water in the Metropolitan area of Guadalajara, considered as a thermo regulatory body. This study used tools such as Rhtest, as well as analyzing extreme climate indices using RClimdex. In addition, the relationship with the change in water surface of Lake Chapala was assessed through the NDWI index, using Landsat images, between 1985 and 2018. According to the obtained results, the signs of climatic variability are detected in the study region, which, directly affects the basin runoff and water levels in the lake, as well as, the factor of water overexploitation in the basin, so it is considered that the lake conditions mostly depend on the type of management that is given to the resource. Finally, the results will help the understanding of climate variability and its water resources influence of the Lerma Chapala basin, which will assist in future research.

In a Water-Cooled Lithium-Lead (WCLL) Breeding Blanket (BB), the heat generated by the plasma thermal radiation and nuclear reactions is removed mainly by two components; namely, the First Wall (FW) and the Breeding Zone (BZ). The FW faces the neutrons and charged particles fluxes generated by the fusion reactions and the thermal radiation coming from the plasma. The present work takes into account the FW cooling system inspired by the WCLL BB 2018 design of DEMO 2017 baseline. Unlike the baseline where a Pressurized-Water Reactor (PWR) setup is used for the coolant, various setup between the Boiling Water Reactor (BWR) and the High-Pressure (HP) BWR are studied in the present work operating in the Two-Phase Flow (TPF) regime. The 3D model of the FW in the WCLL BB 2018 design is simplified into a 1D model and a steady state analysis is carried out to optimize the mass flow rate of the water and the number of parallel channels at the BB cells at different poloidal locations of the reactor, which helps not only in reducing the used coolant but also in improving the Tritium Breeding Ratio (TBR). The present work takes into account forced convection in the liquid only region, the subcooled boiling region, and the saturated boiling region using suitable empirical or semi-empirical models from the literature. The results are validated against the existing results in the literature. In the end, related conclusions are made regarding the pros and cons of the studied operating conditions.

The reliability analysis allows to estimate the system's probability of detecting and identifying outlier. Failure to identify an outlier can jeopardise the reliability level of a system. Due to its importance, outliers must be appropriately treated to ensure the normal operation of a system. The system models are usually developed from certain constraints. Constraints play a central role in model precision and validity. In this work, we present a detailed optical investigation of the effects of the hard and soft constraints on the reliability of a measurement system model. Hard constraints represent a case in which there exist known functional relations between the unknown model parameters, whereas the soft constraints are employed for the case where such functional relations can slightly be violated depending on their uncertainty. The results highlighted that the success rate of identifying an outlier for the case of hard constraints is larger than soft constraints. This suggested that hard constraints should be used in the stage of pre-processing data for the purpose of identifying and removing possible outlying measurements. After identifying and removing possible outliers, one should set up the soft constraints to propagate the uncertainties of the constraints during the data processing. This recommendation is valid for outlier detection and identification purpose.

To understand how the thinning strategies impacts on wood quality and quantity for different purposes is of interest, considering that the management of plantations is carried out with parameters that have yet to be validated for different growth conditions. This work evaluated contrasting thinning regimes applied early at two moments of the crop cycle. With an initial population of 840 trees.ha-1, two thinning with populations ranging from 700 to 400, and from 400 to 100 trees.ha-1 were applied at 1.5 and 7.3 years, respectively. Growth analyses were carried out from the ages of 1.5 to 20.8 years considering: total height, diameter at breast height, individual volume, total and commercial volume per hectare, mean annual increase and current annual increase. At final age, contrasting populations of 100, 250 and 400 trees.ha-1 were sampled to assess wood density, and mechanical properties (bending and compression on small scale clear samples). The values of individual growth and wood properties are related to a Stand Density Index to understand the effect of competition on those values. The results allow us to identify the thinning schemes that record the most significant individual and per-hectare growth (both in thinning and clear felling) and the optimal harvest time under specific growth conditions. We assessed the proportions of commercial logs for sawmill and pulp uses, providing valuable inputs for a subsequent economic analysis of thinning regimes seeking for the most convenient combination of wood products. Wood's physical and mechanical properties assessed were barely affected by contrasting levels of competition between trees, therefore the decision of the silvicultural system to implement will depend on production and economic criteria.

The cutting of difficult-to-machine materials, including their preconditioning, often requires specialised tools and machinery. An alternative processing technology can be cutting materials with a water jet. From the initial stage, the selection of appropriate technological parameters will influence what further finishing treatments will be applied. Vibrations occurring during this process can negatively affect the quality of the cutting edges and surfaces. Therefore, this study analysed vibrations during water-jet cutting with variable technological parameters (speed vfi and pressure pi). To measure the vibrations, a three-axis accelerometer from SEQUOIA was used in water-jet cutting of three materials: aluminum alloy, titanium alloy, and steel. Based on the study, it was found that the maximum value of vibration amplitude reaches the lowest value of vibration acceleration for aluminum alloy (not exceeding 5 m/s2), regardless of the value of pressure during the cutting process. This, taking into account the material properties, indicates that aluminum alloy is the material most susceptible to the cutting process while maintaining a high quality of the cutting surface. Significantly higher values of vibration acceleration amplitude (reaching up to 60 m/s2) during cutting were registered for steel and titanium alloy in all zones and phases of the process (entry zone, cutting zone, and exit zones).

This paper presents a robust method based on graph topology to find the topologically correct and consistent subset of inter-robot relative pose measurements for multi-robot map fusion. However, the absence of good prior gives a severe challenge to distinguish the inliers and outliers, and wrong loop closures can seriously corrupt the fused global map. Existing works mainly rely on the consistency of spatial dimension to select inter-robot measurements, which does not always hold. In this paper, we propose a fast inter-robot loop closure selection method that integrates the consistency and topology relationship of measurements, which both conform to the continuity characteristics of similar scenes and spatiotemporal consistency. The traditional high-dimensional consistency matrix is decomposed into the sub-matrix blocks corresponding to the overlapping trajectory area. Building on this logic, a clustering method involving topology correctness of inter-robot loop closures is introduced to split the entire measurement set into multiple clusters. We define the weight function to find the maximum cardinality subset with topologically correct and consistent, then convert the weight function to a maximum clique problem in the graph and solve it. We evaluate the performance of our method in a simulation and in a real-world experiment. Compared to state-of-the-art methods, the results show that our method can achieve competitive performance in accuracy while reducing computation time by 75%.

Numerical modeling of sedimentation and erosion in reservoirs is an active field of reservoir research. However, simulation of bed-load transport phenomena has rarely been applied to other water bodies, in particular, the fluctuating backwater area. This is because the complex morphological processes between hydrodynamics and sediment transport are generally challenging to accurately predict. In this study, the refinement and application of a two-dimensional shallow-water and bed-load transport model to the fluctuating backwater area is described. The model employs the finite volume method of the Godunov scheme and saturated sediment transport equations. The model was verified against experimental data of a scaled physical model. It was then applied to actual reservoir operation, including reservoir storage, reservoir drawdown and continuous flood process, to predict the morphology of reservoir sedimentation and sediment transport rates and bed level changes in the fluctuating backwater area. It was found that the location and morphology of sedimentation effected by the downstream water level results in random evolution of the river bed, and bed-load sedimentation is transported from upstream to downstream with the slope of the longitudinal section of the river bed generally reduced. Moreover, the sediment is mainly deposited in the main channel and the elevation difference between the riverbank and channel decreases gradually.

The computational model that is able to estimate the temperature distribution inside a solid specimen during the film boiling phase of immersion quenching (water entry) process has been presented in paper, and it is based on the prescribed initial temperatures of the solid specimen and the liquid quenchant. In addition, the turbulence effects have to be considered using the assumed turbulence kinetic energy value, i.e., the “frozen turbulence” approach, that remains constant thorough the simulation. The studied material is nickel alloy, Inconel 600, for which the extensive experimental data is available. The work has been carried out using ANSYS Fluent computational fluid dynamics software and the methods for solution of Stefan problem by Eulerian two fluid VOF model.. A satisfactory agreement between the experimental and the calculated data has been achieved, yielding thereby the computationally obtained data that fits to a great extent to the prescribed error band of ± 10 % during the estimated film boiling phase of the immersion quenching process itself.

Agricultural crops productivity is heavily influenced by the strength of their seeds. Current methods for testing seed vigor, such as the germination rate and tetrazolium test, rely on time-consuming human visual inspections. Computer Vision, a crucial technology in smart production processes, offers an automated alternative and is increasingly applied in digital agriculture processes. Here we propose a method that combines YOLOv8 and morphological analysis of seeds using X-ray images to aid seed quality analysts in classifying seed lots based on their physiological potential. We examined the internal morphology of three seed lots and generated X-ray images to train a YOLOv8-based model with a post-segmentation module. This model assessed various parameters such as the total seed area, area filled by the embryo and endosperm, length, width, and calculated the percentage occupied by the embryo and endosperm in relation to the total seed area. Subsequently, seeds were classified into four categories based on the internal area occupied by the endosperm and embryo. Our findings reveal the robust performance of the YOLOv8 model in segmenting and classifying despite the challenges posed by a relatively small dataset. Notably, the proposed model achieved an impressive accuracy of up to 95.6% in identifying and segmenting the endosperm over 1,500 epochs with just 15 training images. The endosperm/seed area ratio, particularly within the 50-60% range covering over 50% of the samples, emerged as a significant metric for evaluating the viability of seed batches.

One of the main challenges in geodetic deformation analysis is to infer whether the geometry of some engineering structures or zones of natural hazards has changed from their initial state or not. The pillar that supports such an analysis is tightly based on the fundamentals of statistical hypothesis testing. The null hypothesis model indicates that no displacement has occurred. It is tested against a class of alternative models, which stipulate different displacement patterns. In this contribution, we present an innovative geodetic displacement detection which integrates combinatorial analysis and likelihood ratio tests into a sequential procedure for the case where the differences between observations of two epochs are in play. This framework is applied and investigated to two test scenarios: a synthetic and a real simulated trilateration network. From a statistical point of view, our approach is rigorous, because the alternative model can identify simultaneously more than one unstable point. In addition, the relationship between the unknown parameters and the observations is always linear, even if the problem manifests itself as non-linear. Consequently, we avoid a potential loss of statistical test power due to the model linearization. In addition, the proposed method controls the false positive rate efficiently. One of the problems that arise here is also related to the selection of the maximum number of points to be considered in the test procedure ( ). Here, we provide an innovative methodology based on rank computation of the design matrices to define , which can even be extended to the problem of outlier detection. Determining avoids the problem of having non-separable models in identifying unstable points. The algorithms and data are available in the repository.

Hospitals are perpetually challenged by the dual requirements of concurrently improving the quality of healthcare and maintaining financial solvency. Both issues are among the top concerns for hospital executives across the United States, yet some have questioned if the efforts to enhance quality are financially sustainable. led us to examine if improving quality in the hospital setting impacts revenue. Using multivariate regression, we assessed if numerous quality measures were associated with our targeted measure of hospital profitability: the net patient revenue per adjusted discharge. The independent variables included the HCAHPS Summary Star Rating, Hospital Compare Overall Rating, All-Cause hospital-wide Readmission Rate, Total Performance Score, Clinical Outcomes Domain Score, Safety Domain Score, Person and Community Engagement Domain Score, and the Efficiency and Cost Reduction Score. Our results indicated that improving quality was significantly associated with improved net patient revenue per adjusted discharge for seven of the eight of these quality measures at the hospital level. It is clear that failing to address quality and patient safety issues is costly for US hospitals, thus we believe our findings support the premise that increased attention to the quality of care delivered as well as patients’ perceptions of care may allow hospitals to accentuate profitability and advance a hospital’s financial position.

Embryo quality evaluation during in vitro development is vital for the success of assisted reproductive technologies (ART). However, the subjective morphological assessment by embryologists may result in inconsistencies that affect the selection of the best embryo for transfer. To provide a more comprehensive evaluation of embryo quality, we performed the integration of embryo metabolomics with standardized morphokinetic classification. The culture medium of 55 embryos (from 21 couples undergoing ICSI) was collected at two timepoints (day 3 and 5). Samples were split into Good (n=29), Lagging (n=19) and Bad (n=10) according to embryo morphokinetic evaluation. Embryo metabolic performance was assessed by 1H-NMR, monitoring the variation of specific metabolites (pyruvate, lactate, alanine, glutamine, acetate, formate). Adjusted metabolite differentials were observed during the first three days of culture and found to be discriminative of embryo quality at the end of day 5. Pyruvate, alanine, glutamine, and acetate were major contributors to this discrimination. Good and Lagging embryos were found to export and accumulate pyruvate and glutamine in the 3 first days of culture, while Bad embryos consumed them. This suggests that Bad embryos have a less active metabolism than Good and Lagging embryos and these two metabolites as putative biomarkers for embryo quality. This study provides a more comprehensive evaluation of embryo quality and can lead to improvements in ART by enabling the selection of the best embryos. By combining morphological assessment and metabolomics, the selection of high-quality embryos with the potential to result in successful pregnancies may become more accurate and consistent.

Eutrophication is a major environmental issue with many negative consequences, such as hypoxia and harmful cyanotoxins production. Monitoring coastal eutrophication is a crucial, especially for island countries like the Republic of Cyprus, which are economically dependent on the touristic sector. Additionally, the open-sea aquaculture industry in Cyprus has been exhibiting an increase in the last decades and environmental monitoring to identify possible signs of eutrophication is mandatory according to the legislation. Therefore, in this modelling study, two different types of Artificial Neural Networks (ANNs) are developed based on in situ-data collected from stations located in the coastal waters of Cyprus. Theses ANNs aim to model the eutrophication phenomenon based on two different data-driven modelling procedures. Firstly, the self-organizing map (SOM) ANN examines several water quality parameters (specifically water temperature, salinity, nitrogen species, ortho-phosphates, dissolved oxygen and electrical conductivity) interactions with the Chlorophyll-a parameter. The SOM model enables us to visualize the monitored parameters relationships and to comprehend complex biological mechanisms related to Chlorophyll-a production. A second feed-forward ANN model is also developed for predicting the Chlorophyll-a levels. Based on this ANN model, several scenarios associated to the eutrophication-related water quality parameters can be extracted. The combination of these two ANNs models is considered a holistic modelling approximation for the identification of eutrophication scenarios, since it enables not only the prediction of the Chlorophyll-a parameter levels, but also the “capturing” of hidden biological mechanisms associated with algal production.

Soil water loss by evaporation influences the sodium adsorption ratio (SAR) of irrigation drainage water. Evaporation concentrates sodium and magnesium but calcite precipitation has a more complicated effect on soluble calcium and alkalinity. Here we propose a revised sodicity hazard assessment that quantifies the impact of evaporative water loss and calcite precipitation on drainage water SAR. This paper shows sodicity hazard is determined by the initial composition of irrigation water as originally suggested by previous researchers, and provide a simple, accurate way to identify the potential sodicity hazard of any irrigation water. In particular, the initial equivalent concentration of alkalinity and calcium determine the salinization pathway followed during evaporation. If the irrigation water alkalinity exceeds soluble calcium expressed as equivalent concentrations, drainage water SAR approaches an upper limit determined by the initial relative concentration of sodium and magnesium. If irrigation water alkalinity is less than soluble calcium, drainage water SAR approaches a lower limit determined by the initial calcium, magnesium and sodium. In both cases the SAR is scaled by the square root of the concentration factor √Fc quantifying soil water loss. To assess the impact of evaporation and calcite precipitation on the SAR and test the accuracy of the new sodicity hazard assessment, we evaluated data from previously published lysimeter studies. We plotted water composition boundaries for each source water, comparing these boundaries to the drainage water composition recorded in the lysimeter studies. As salinity increased by evaporation, each drainage water followed a distinct salinization path.

Easy to use satellite-based water quality visualizations are needed for monitoring and understanding coastal and inland waters, but to date, no publicly accessible real-time global visualization system was in place. Here we introduce the Ulyssys Water Quality Viewer (UWQV), a Sentinel Hub EO Browser Custom script designed for qualitative views of aquatic chlorophyll and suspended sediment concentrations. The viewer avoids unmixing of the chlorophyll and suspended sediment spectral signal by visualizing these parameters together, with high concentrations of suspended sediment obscuring chlorophyll if present. Cloud masking uses the Hollstein and Braaten algorithms (existing EO Browser custom script code), additionally water surfaces are masked using the Normalized Differential Water Index. Chlorophyll is estimated using reflectance line height-based indicators such as fluorescence line height and maximum chlorophyll index. Suspended sediment is visualized based on single-band reflectances at 620 or 700 nm. Data sources are Sentinel-2 and Sentinel-3 images, allowing either 20 m spatial resolution or up to daily imaging. This visualization system is easy to operate and interpret, and combined with the data service capacity of the Sentinel Hub, it is expected that UWQV will contribute to monitoring of remote water bodies and to our overall understanding of physical limnology and aquatic ecology.

Polluted rivers are a primary problem in Changhua County, Taiwan, due to rapid and massive developments in agriculture and industry. In this study, samples consisted of water influent from the Yangzi-Cuo River, Ci-Tong Jiao, Changhua County. Ecology technology, a combination of gravel contact oxidation and surface flow constructed wetlands, was employed to enhance the water quality. Ecology technology is a useful and ordinary process that focuses on original treatment of pollution through chemical, physical, and biological procedures based on the mediums of soil, plant, water, and microorganisms from pure environments. Moreover, this study aimed to minimize the river pollution index (RPI) of the Yangzi-Cuo River by using combinations of gravel contact oxidation and surface flow constructed wetlands. The inflow volume of the water samples in situ was found to be 1534–2261 cubic meters per day (CMD). The pollution in the water sample mostly involved suspended solid (SS), ammoniacal nitrogen (NH₃–N), total phosphorus (TP), total nitrogen (TN), and biochemical oxygen demand (BOD), and the values of the above indexes were found to be 10.0–26.7 mg/L, 0.9–14.0 mg/L, 1.2–14.1 mg/L, 11.1–18.2 mg/L, and 0.5–3.6 mg/L, respectively. Efficiencies of pollution elimination in SS, NH₃–N, TP, TN, and BOD were found to be 24.2–93.1%, 58.3–86.2%, 5.2–85.0%, 59.4–77.2%, and 46.3–76.4%, correspondingly, after purification treatment via ecology technology. Thus, ecology technology is a valid means of purification treatment for polluted rivers.

The greater Wellington region, New Zealand, is highly vulnerable to large earthquakes because it is cut by active faults. Bulk water supply pipelines cross the Wellington Fault at several different locations, and there is considerable concern about severe disruption of the provision of reticulated water supplies to households and businesses in the aftermath of a large earthquake. A number of policy initiatives have been launched encouraging householders to install rainwater tanks to increase post-disaster resilience. However, little attention has been paid to potential health hazards associated with consumption of these supplies. To assess health hazards for householders in emergency situations, six 200-litre emergency water tanks were installed at properties across the Wellington region, with five tanks being allowed to fill with roof-collected rainwater and one tank being filled with municipal tapwater as a control. Such tanks are predominantly set aside for water storage, and once filled, feature limited drawdown and recharge. Sampling from these tanks was carried out fortnightly for one year, and samples analysed for E. coli, pH, conductivity, a range of major and trace elements, and organic compounds, enabling an assessment of the evolution of water chemistry in water storage tanks over time. Key findings were that the overall rate of E.coli detections in the rain-fed tanks was 17.7%, which is low in relation to other studies. We propose that low incidences of E.coli may be due to biocidal effects of high zinc concentrations in tanks, originating from unpainted galvanised steel roof cladding. Lead concentrations were high compared to other studies, with 69% of rain-fed tank samples exceeding the World Health Organisation’s health-based guideline of 0.01 mg/L. Further work is required to determine risks of short-term consumption of this water in emergency situations.

The water and wastewater sectors are energy-intensive, and so a growing number of utility companies are seeking to identify opportunities to reduce energy use. Though England’s water sector is of international interest, in particular due to the early experience with privatisation, for the time being very little published data on energy usage exists. We analyse telemetry data from Thames Water Utilities Ltd. (TWUL), which is the largest water and wastewater company in the UK and serves one of the largest mega-cities in the world, London. In our analysis, we (1) break down sectoral energy use into their components, (2) present a statistical method to analyse the long-term trends in use, as well as the seasonality and irregular effects in the data, (3) derive energy-intensity (kWh m³) figures for the system, and (4) compare the energy-intensity of the network against other regions in the world. Our results show that electricity use grew during the period 2009 to 2014 due to capacity expansions to deal with growing water demand and storm water flooding. The energy-intensity of the system is within the range of reported figures for systems in other OECD countries. Plans to improve the efficiency of the system could yield benefits in lower the energy-intensity, but the overall energy saving would be temporary as external pressures from population and climate change are driving up water and energy use.

Cyanobacteria are ubiquitous phototrophic bacteria that inhabit diverse environments across the planet. They dominate many eutrophic lakes impacted by excess nitrogen (N) and phosphorus (P) forming dense accumulations of biomass known as cyanobacterial harmful algal blooms or cyanoHABs. Their dominance in eutrophic lakes is attributed to a variety of unique adaptations including N and P concentrating mechanisms, N fixation, colony formation that inhibits predation, vertical movement via gas vesicles, and the production of toxic or otherwise bioactive molecules. While some of these molecules have been explored for their medicinal benefits, others are potent toxins harmful to humans, animals, and other wildlife known as cyanotoxins. In humans these cyanotoxins affect various tissues, including the liver, central and peripheral nervous system, kidneys, and reproductive organs among others. They induce acute effects at low doses in the parts-per-billion range and some are tumor promoters linked to chronic diseases such as liver and colorectal cancer. The occurrence of cyanoHABs and cyanotoxins in lakes presents challenges for maintaining safe recreational aquatic environments and the production of potable drinking water. CyanoHABs are a growing problem in the North American (Laurentian) Great Lakes basin. This review summarizes information on the occurrence of cyanoHABs in the Great Lakes, toxicological effects of cyanotoxins, and appropriate numerical limits on cyanotoxins in finished drinking water.

The study aimed to evaluate the after-effects of the COVID-19 pandemic on the sleep quality and patterns of women across different cultural settings within Iraq, spanning the period of 2022. A cross-sectional survey was administered to a diverse cohort of women from multiple provinces in Iraq. The survey measured various parameters, including sleep duration, onset latency, and disturbances. The post-pandemic period has seen a notable decline in sleep quality among the female population. Contributing factors include psychological stress, lifestyle changes due to the pandemic, and ongoing socio-economic challenges. The impact on sleep quality exhibited variation across different cultural groups, indicating a significant cultural influence on the pandemic's psychological aftermath. The study concludes that the post-pandemic phase has adversely affected the sleep health of women in Iraq, with cultural factors playing a critical role in these changes. There is a pressing need for culturally sensitive public health strategies to address sleep disturbances and mitigate their long-term effects on women's health. Public health initiatives should be tailored to address the specific cultural contexts within Iraq to improve sleep health among women. Further research is warranted to explore the long-term consequences of disturbed sleep patterns and the effectiveness of different intervention strategies.

A framework for the review of existing water management systems and their transformation into robust water sharing systems is offered. The framework focuses on the need to develop efficient and equitable ways to manage water scarcity and plan to deal with the tensions scarcity imposes on any community. The framework identifies a way to bring together traditional community-managed systems with those typically used to allocate water to large water users and more commonly found in developed countries. So that use can be kept within sustainable limits while optimizing use, the framework includes mechanisms that enable the reallocation of water as demand and supply conditions change. Non-consumptive uses are recognized and environmental objectives can be delivered efficiently. Compliance with well-established accounting and hydro-logical concepts. Ways to increase the value of existing entitlements, encourage innovation and protect investments are included as options. It is recognized that the governance and legal arrangements necessary to underpin successful implantation are context specific.

Water resources are threatened nowadays by pollution that comes from domestic, industrial and agricultural discharges without prior treatment. This pollution causes the degradation of water quality. Surface pollutants can seep through the soil into water tables. The objective of our work is to assess and control the physicochemical quality of the Chari Baguirmi groundwater, to protect human health. The quality of 83 boreholes was assessed, while performing analysis for 12 physicochemical parameters at the National Water Laboratory and at the Center for Quality Control of Foodstuffs in Chad. These parameters are: pH, EC, Ca2+, Mg2+, Na+, K+, Cl-, SO42-, NH4+ and NO3- , Fe2+ and HCO3-. Also, the results obtained were compared with WHO standards. The geochemical statistical approach has made it possible to characterize the hydro geochemical properties and to understand the major processes of the mineralization of groundwater resources in Chari Baguirmi region in Chad. Some of its waters are acidic and weakly mineralized, rich in Fe2+ and NH4+. The origin of the mineralization is due to the alteration of the host rocks and to the hydrolysis of silicate and ferromagnesian minerals as well as anthropogenic pollution. The ammonium concentrations in N’Djamena boreholes are higher than WHO standards, indicating the presence of pollution which may come from organic waste. These results constitute a preliminary step in understanding hydro geochemical functioning and a basis for monitoring the physicochemical quality of the water in the study area.

Studies have found critical software malfunctions responsible for some of the worst accidents in recent times. These malfunctions are often only minor defects that snowball into large problems; a few lines of code is all it takes. Complexity, safety, quality, and resilience are among the key attributes defining a software’s operational success. There are many leading factors for complexity, such as increases in the product size, the rate of requirement changes, and the number and type of stakeholders, and failure to manage these issues efficiently always has the same consequence, i.e., massive failure and sometimes technological catastrophe. This work analyzes some of the architecture, design, and implementation guidelines used as detection and mitigation techniques. It also discusses the safety considerations, as considering how the steam industry has handled safety issues could offer some guidance for ensuring safety. Complexity in such systems also causes some of the worst side effects from the quality auditor's perspective. While failures in the software are hard to predict, one of the most significant ways of showing preparedness is practicing software resilience. New mitigation areas, such as the fragility spectrum and failure obviation, and their usage for building a safer system are analyzed. Also discussed are various architecture styles in practice and the dramatic effect human factors can have on the success of the software being developed.

The aim of the study was to test the significance of the EPT index in the water quality assessment of three types of water bodies in hilly and mountainous region of Serbia. The aquatic macroinvertebrate community was dominated by the group of insects, of which 95 taxa represent the EPT group. We compared the obtained values of biological indices used for the assessment of water quality according to the national legislation with the overall status assessment represented by the ecological quality classes (EQC). The results of the Spearman correlation test showed a negative correlation of EQC with the EPT index, BMWP score, H', total number of taxa and number of sensitive taxa, while a positive correlation was observed for the values of SI and Tubificinae %. The values of EQC and biological indices were subjected to principal component analysis (PCA). The results showed that the parameters that contributed most to the differences were the EPT index, the BMWP score and the number of sensitive taxa. The results indicate that the EPT index is an excellent indicator of changes in water quality and an important tool for the ecological categorization of water bodies in mountain regions.

A paddle wheel aerator is developed in this research, which includes a wireless sensor network for measuring the water quality in the aquaculture of marine shrimp ponds. It can also move to the desired position to fill oxygen and measure water quality. A basic requirement is good standard water quality to prevent shrimp from epidemics and improve production. The water quality paddle wheel aerator applies a microcontroller and sensors to measure eight parameters of water quality. These water quality parameters are observed on the web application via an IoT module. The movement system of the water-quality paddle wheel aerator consists of a LiDAR, GPS, and remote RF signal. Each item of data is recorded immediately on the cloud server while the water-quality paddle wheel moves in the marine shrimp farm. The controlled paddle wheel aerator is harnessed automatically to enhance precisely the spatial monitoring resolution of the measurement system installed, which is needless for a multiple measurement system with high cost of investment. Also, farmers can access real data through the Line application. Hence, they are able to plan and control a good environment for aquaculture, preventing the occurrence of various epidemics and decomposing organic matter in the pond.

Irrigation and fertilization are indispensable links in the jujube planting industry in southern Xinjiang, China. However, the water and fertilizer integration effects on jujube growth and fruit quality remain unclear. A two-year water and fertilizer optimization coupling test was conducted to determine the optimal water- and nutrient-supply scheme. The three-factor randomized block experiment included water (W), nitrogen (N), and phosphorus (P). According to the principal component analysis of each index, each treatment’s comprehensive score was obtained. Using yield and economic regression models, the theoretical value and yield value of the optimal economic benefit are inferred. When W, N, and P were applied together, the fruit quality and yield of each treatment significantly differed, and the vitamin C, soluble sugar, and sugar–acid ratio increased significantly with an increase in nitrogen fertilizer. However, the titratable acid decreased. An increase in irrigation and nitrogen application significantly increased fruit yield. The comprehensive score was the highest in the N3P3W2 treatment, which improved fruit quality, and the lowest in the N4P3W2 treatment. When the amounts of N, P, and W were 275.56 kg·hm-2, 413.66 kg·hm-2, and 7278.19 m3·hm-2, respectively, the theoretical economic benefit was the best. The N4P3W2 treatment is the optimal treatment.

Water quality is the measure of chemical, physical and biological suitability of water in relation to natural effects and intended purpose which may affect human health and aquatic life. Assessment of water quality is very essential for the management of water resources and human health. Traditionally, in-situ measurements have been used to obtain the water quality parameters of the water bodies. However, with the availability of satellite images, researchers have shown that satellite images are a reliable tool that can be used to estimate water quality. Satellite image-derived water quality parameters provide extensive spatial extent and large temporal variations when compared to traditional in situ sample collection and laboratory measurements. The present work estimated several parameters for quality of water in the Kamuzu reservoir of Lilongwe River for the 2013-2020 period using Sentinel-2 and Landsat-8 satellite images. The band ratio algorithms were used to retrieve Chlorophyll a (Chl-a), Turbidity, Total Suspended Matter (TSM), Secchi depth, Coloured Dissolved Organic Matter (CDOM), and Cyanobacteria from the reservoir. Turbidity and TSM were compared with the in-situ data collected over the same period. The comparison indicated R² of 0.9 and 0.69 for TSM and Turbidity respectively from Sentinel-2 images whereas R² of 0.56 and 0.61 was obtained using Landsat 8 images which are quite encouraging. The other set of results included the spatial distribution maps of water quality parameters using Landsat-8 and Sentinel-2 satellite data. It was observed that the spatial distribution of water quality parameters, except for CDOM and Cyanobacteria, showed very good distribution and matches with the theoretical results. However, for CDOM and Cyanobacteria, the distribution was almost similar for the entire study area and the band ratio algorithm may not be able to estimate them quite reasonably. This research reiterates the need for the use of remote sensing in estimating the water quality parameters and may be a substitute to the in-situ data, in terms of spread and frequency, which is very common to most of the water bodies, across the globe.

The utilization for water resource has been of great concern to human life. To assess the natural water system in Kangding County, the integrated methods of hydrochemcial analysis, multivariate statistics and geochemical modelling were conducted on surface water, groundwater and thermal water samples. Surface water and groundwater were dominated by Ca-HCO₃ type, while thermal water belonged to Ca-HCO₃ and Na-Cl type. The analyzing results concluded the driving factors that affect hydrochemical components. Following the results of the combined assessments, hydrochemcial process was controlled by the dissolution of carbonate and silicate minerals with slight influence from anthropogenic activity. The mixing model of groundwater and thermal water was calculated using silica-enthalpy method, yielding cold-water fraction of 0.56-0.79 and estimated reservoir temperature of 130-199 ^oC, respectively. δD and δ¹⁸O isotopes suggested surface water, groundwater and thermal springs were of meteoric origin. Thermal water should have deep circulation through the Xianshuihe fault zone, while groundwater flows through secondary fractures where it recharges with thermal water. Those analytical results were used to construct a hydrological conceptual model, providing a better understanding of the natural water system in Kangding County.

Using numerical software to establish a three-dimensional geological model of shield tunneling through fault fracture zones, considering the synchronous grouting effect at the shield tail, the disturbance of various geotechnical structures in the fault fracture zone under deep burial and high water pressure conditions is studied. According to the comparison between the numerical model analysis results and the on-site inspection results of the entire process of Shiziyang B3 section, synchronous grouting at the shield tail is the main reason for the changes in soil and water pressure in the fault fracture zone area. The soil and water pressure changes strongly during shield tunneling, and the maximum excess pore pressure value occurs when the shield tail passes. When the shield tunneling machine is far away, the soil and water stress shows a downward trend. The impact of synchronous grouting decreases with the increase of tunneling distance. Due to the difference in permeability, the variation law of pore pressure in the fault fracture zone is significantly different from the original rock, leading to a faster increase in pore pressure in the fracture zone area and a wider range of influence.

After the arrival of a new airborne virus to the world, science is aiming to develop solutions to withstand the spread and contagion of the SARS-CoV-2 coronavirus. The most severe among the adopted measures is to remain in home isolation for a significant number of hours per day, in order to avoid the spreading of the infection in an uncontrolled way through public spaces. Recent literature showed that the major route of transmission is via aerosols produced especially in poorly ventilated inner spaces. With regard to contagion rates, accumulated incidence or number of hospitalizations due to COVID-19, Spain has reached very high levels, therefore this article develops a quantitative and qualitative analysis of the requirements established in Spain with respect to the European framework in reference to ventilation parameters indoors. For this, a case study has been analyzed, representing a common residence in current Spanish residential developments. Results show that the criteria established in the applicable regulations are not sufficient to ensure health as well as to avoid contagion by aerosols indoors.

Three-phase AC electric arc furnace (EAF) is a typical non-linear load, causing many power quality problems. Most of the researches on the voltage problems of EAF mainly focus on the voltage fluctuation, and less on the transient voltage problems caused by EAF short circuit and open circuit. In this paper, the relationship between voltage and current of EAF is obtained by combining hyperbolic function and exponential function, then the white noise and chaotic circuit are added to establish the EAF model which is suitable for the study of voltage fluctuation and transient voltage. This paper analyzes the causes of the transient voltage problem of the EAF, calculates the short-circuit current, reactive impact and the influence on voltage at the point of common coupling (PCC) in the three-phase short-circuit of the EAF, and compares the calculation results with the simulation results to prove the accuracy of this model. The results show that the reactive impact of three-phase short circuit is about twice as much as that of normal operation of EAF, resulting in about 30% voltage sag at the PCC, which is very unfavorable to the power grid. This paper provides reference for transient power quality evaluation and dynamic reactive power compensation of EAF.

Dental implants provide a predictable treatment option for partial and complete edentulism via the placement of fixed permanent artificial root to support prosthetic dental crowns. Despite the high survival rates, long-term implant failures are still reported leading to implant removal and additional financial and health burdens. While extrinsic factors that improve survival rate of implants have been well explored, the impact of genetic factors on this matter is poorly understood. A systematic review and meta-analysis study was conducted to determine whether genetic factors contribute to increase the risk of dental implant failure. A comprehensive search for peer-reviewed articles on dental implants and genetics was performed using various literature database libraries. The study design was conducted according to PRISMA guidelines, and the obtained records were registered in PROSPERO database. According to the exclusion/inclusion criteria, 11 studies were eligible for this study out of 808 articles. The meta-analysis of the combined association studies of DNA variations and dental implants did not indicate an increase risk for implant failure due to DNA variations in IL-1B, IL-10 and TNF-α. This study emphasizes the need for larger randomized controlled clinical trails to inform clinicians and patients about the role of genetic factors on dental implant survival and success rate in healthy and compromised patients.

In recent years, Chinese manufacturing enterprises compete to chase the wave of "digital revolution", digital empowerment has become an important strategic path of technological reform for many manufacturing enterprises. Based on the micro data of listed companies, this paper investigates the impact of digital transformation of Chinese listed companies on the quality of their export products. It is found that digital transformation can significantly improve the quality of enterprises' export products. After a series of robustness tests, this conclusion is still valid, and there are two ways to improve innovation performance and total factor productivity. The export product quality enhancement effect of enterprise digital transformation also has the heterogeneity of ownership, region and industry. In the further study, this paper also examines the impact of digital transformation on the internal salary gap of enterprises, and finds that digital transformation may increase the internal salary gap of enterprises, and form a "masking effect" on the quality of export products. To a certain extent, this paper deepens the understanding of the study of enterprise digital transformation on the quality of export products and its differences, and provides certain guidance for enterprises to implement the strategy of digital transformation.

(1) Background: Most of the existing studies focus on the evaluation of technology finance; the relationship between technology finance and technology innovation. But there are few studies on the development of technology finance and the quality of economic development in our country; (2) Methods: Based on the panel data of 30 provinces in China, this paper constructs an index system to measure the development of technology finance through the improved entropy method, and tests the spatial correlation of the development of technology finance in China by Moran'I index. According to the test results, this paper constructs a spatial econometric model to empirically analyze the promoting effect of scientific, technological and financial development on high-quality economic development, and analyzes its promoting effect in different regions and different time periods; (3) Results: The results show that the quality of China's economic growth is spatially dependent, and the development of science, technology and finance can significantly promote the quality economic development in China. And the promotion coefficient of the central region is the largest, as well as the coefficient of the eastern region is the smallest. The promotion coefficient was small and not significant before 2015, and was significantly positive after 2015; (4) Conclusions: this paper puts forward the corresponding policy recommendations according to the research results.

In recent years, since flood disasters have brought immeasurable losses to the city, it is urgent to prevent and solve the flood of stagnant water. Considering the shortage of real-time and accuracy of hydrological analysis, Opencv technology is used in this paper to process the obtained data in real time. For improved Yolov5, BoTNet and GAMAttention Transformer are used to improve Yolov5 to enhance its ability of recognition and prediction to better identify surface gathered water. The prediction rate of the improved Yolov5 is 7.1% higher than that of Yolov7 and 1.7% higher than that of Yolov5.After that, contour preprocessing of the image is carried out through the cropping technology of the identification frame to eliminate relatively unstable factors. The principle of binocular distance measurement is used to measure the three-dimensional coordinates of the actual distance, better constrain the contour proportion of the picture, and then the Opencv technology is used to get the outline of the water, and HSV is combined with better color processing pictures for the identification of the water and contour generation, and the area is obtained to correspond to the corresponding parameters of flood to provide important help in flood prevention and storm drainage.

Based on NCEP FNL 1°*1° analysis data and Xinjiang meteorological bureau area numerical operation prediction, a local precipitation event in southern Xinjiang on June 26 was analyzed, and the results showed that the water vapor involved in this process originated from the northwestern Gangetic Plain and was transported along the Indus River plain and over the northwestern end of the mountains. Driven by the Iranian low-pressure trough, water vapor at 500 hPa was transported across the northwestern end of the Gangdise Mountains, past Georgoli Peak, and northwest over the Kunlun Mountains to arrive in southern Xinjiang.

Electrification coverage in Sarawak is the lowest at 78.74%, compared to Peninsular Malaysia at 99.62% and Sabah at 82.51%. Kapit, Sarawak with its 88.4% populations located in rural areas and mostly situated along the main riverbanks has great potential to generate electrical energy by hydrokinetic system. Yearly water velocity data is the most significant parameter to perform hydrokinetic analysis study. Nevertheless, the data retrieved from local river databases are inadequate for river energy analysis, thus hindering its progression. Instead, flow rates and rainfall data had been utilised to estimate the water velocity data. This signifies no estimation of water velocity in an unregulated river by using water level data had been made. Therefore, a novel technique of estimating the daily average water velocity data in unregulated rivers is proposed. The modelling of regression equation for water velocity estimation was performed and two regression model equations were generated to estimate both water level and water velocity on-site and proven to be valid as the coefficient of determination values had been R² = 87.4% and R²=87.9%, respectively. The combination of both regression model equations can be used to estimate long-term time series water velocity data for type-C unregulated river in remote areas.

The technique of obtaining information or data about any feature or object from afar, called in technical parlance as remote sensing, has proven extremely useful in diverse fields. In the ecological sphere, especially, remote sensing has enabled collection of data or information about large swaths of areas or landscapes. Even then, in remote sensing the task of identifying and monitoring of different water reservoirs has proved a tough one. This is mainly because getting correct appraisals about the spread and boundaries of the area under study and the contours of any water surfaces lodged therein becomes a factor of utmost importance. Identification of water reservoirs is rendered even tougher because of presence of cloud in satellite images, which becomes the largest source of error in identification of water surfaces. To overcome this glitch, the method of the shape matching approach for analysis of cloudy images in reference to cloud-free images of water surfaces with the help of vector data processing, is recommended. It includes the database of water bodies in vector format, which is a complex polygon structure. This analysis highlights three steps: First, the creation of vector database for the analysis; second, simplification of multi-scale vector polygon features; and third, the matching of reference and target water bodies database within defined distance tolerance. This feature matching approach provides matching of one to many and many to many features. It also gives the corrected images that are free of clouds.

Through the process of paradigm change (water as a resource towards water as a common), the authors examine, from a theoretic point of view, the water governability proposed by Agenda del Agua Cochabamba (AdA) – Cochabamba Water Agenda – in the Cochabamba Valley (Bolivia), identifying barriers and drivers to the process that could take place. The rise of Evo Morales in Government in 2006 suggested that policy making would somehow take a fundamental turn resulting in more poor environmental-oriented water policies. However, if that was indeed the case, the implementation of these policies remain controversial as strong power asymmetries still exist at a local level that interfere with national policies shaping the political area. The Cochabamba Water Agenda echoes this debate on the political arena and contributes a politically contested water management through a paradigm change envisaging the difficulties through its implementation. The question remains if this “political” solution to paradigm change in water management may reduce water conflicts.

Efforts to enhance quality control (QC) practices in chip seal construction have predominantly relied on single surface frictional metrics such as mean profile depth (MPD) or friction number. These metrics assess chip seal quality by targeting issues such as aggregate loss or excessive bleeding, which may yield low friction numbers or texture depths. However, aggregate loss particularly due to snowplow operations doesn't always result in slippery conditions and may lead to uneven surfaces. The correlation between higher MPD or friction number and superior chip seal quality isn't straightforward. This research introduces an innovative machine learning-based approach to enhance chip seal QC. Using a hybrid DBSCAN-Isolation Forest model, anomaly detection is conducted on a dataset comprising 183,794 20-meter MPD measurements from actual chip seal projects across six districts in Indiana. This results in typical 20 m-segment MPD ranges of [0.9, 1.9], [0.6, 2.1], [0.3, 1.3], [1.0, 1.7], [0.6, 1.9], and [1.0, 2.3] for the respective six districts in Indiana. A two-step QC procedure tailored for chip seal evaluation is proposed. The first step calculates outlier percentages across 1-mile segments, with an established limit of 25% outlier segments per wheel track. The second step assesses unqualified rates across projects, setting a threshold of 50% for 1-mile unqualified wheel track segments. While the results are data-specific, this framework offers pavement construction practitioners a foundational QC standard for chip seal projects.

Environmental monitoring is an important topic and serves a vibrant scientific role by revealing long-term trends that can lead to new knowledge and understanding. Globally, there is active development of photonic sensors incorporating multidisciplinary research. The ultimate objective is to develop small, low-cost, sensitive, selective, quick, durable, remote-controllable sensors that are resistant to electromagnetic interference. Different photonic sensor designs and advances in photonic frameworks have shown the possibility to realize these capabilities. In this review paper, the latest developments in the field of optical waveguide and fiber-based sensors which can serve for environmental monitoring are discussed. Several important topics such as toxic gas, water quality, indoor environment, and natural disaster monitoring are reviewed.

A milk drink flavored with dates syrup produced at a lab scale level was evaluated. The production process of date syrup involves a sequence of essential unit operations, commencing with the extraction, filtration, and concentration processes from two cultivars: Sukkary and Khlass. Date syrup was then mixed with cow’s and camel’s milk at four percentages to form a nutritious, natural, sweet, and energy milk drink. Sensory, physical, and chemical characteristics of the milk drinks flavored with date syrup were examined. The objective of this work was to measure physiochemical properties of dates fruits and milk drinks flavored with dates syrup, then to evaluate the physical properties of milk drinks utilizing a non-destructive NIR spectra. The study assessed the characteristics of the milk drink enhanced with date syrup by employing near-infrared spectra (NIR) spectra and analyzed utilizing partial least-square regression (PLSR) and artificial neural network (ANN) analysis. The NIR spectrum proved to be highly effective in estimating the physiochemical attributes of the flavored milk drink. The ANN model outperformed the PLSR model in this context. RMSECV is considered a more reliable indicator of a model's future predictive performance compared to RMSEC, R2 ranged between 0.946 and 0.989. Consequently, non-destructive NIR technology demonstrates significant promise for accurately predicting and contributing to the entire production process of the product's properties examined.

The presented results of simulations take into account the optical parameters of the selected sea region (from literature data on the southern Baltic Sea) and two optically extreme types of crude oil (from historical data) which exist in the form of a highly diluted oil-in-water emulsion (10 ppm). The spectral index was analyzed based on the results of modelling the radiance reflectance distribution for almost an entire hemisphere of the sky (zenith angle from 0 to 80o). The spectral index was selected and is universal for all optically different types of oil (wavelengths 650 and 412 nm). The possibility of detecting pollution in the conditions of the wavy sea surface (as a result of wind of up to 10 m/s) was studied. It has been also shown that if the viewing direction is close to a direction perpendicular to the sea surface, observations aimed at determining the spectral index are less effective than observation under the zenith angle of incidence of sunlight for all azimuths excluding the direction of sunlight specular reflection.