African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

By this contribution we would like to briefly highlight the problems in conceiving the “Hydrogen Bond” (HB) as a real short-range, directional, electrostatic, attractive interaction and to reframe its nature through the non-approximated view of condensed matter offered by a Quantum Electro-Dynamic (QED) perspective. We focus our attention on water, as the paramount case to show the effectiveness of this 40-years’ old theoretical background, which depicts water as a two-fluid system (where one of the two phases is coherent). The HB emerge to be the result of the electromagnetic field gradient in the coherent phase of water, whose vacuum level is lower than the non-coherent (gas-like) fraction. Thus, the HB can be properly looked at, i.e. no more as a “dipolar force” among molecules, but as the phenomenological effect of their collective thermodynamic tendency to occupy a lower ground-state, compatibly with temperature and pressure. This perspective allows to account for many “anomalous” behaviours of water and to understand why the calculated energy associated to HB should change when considering two molecules (water-dimer), or the liquid state, or the several kinds of ice. The emergence of a condensed, liquid, phase at room temperature is indeed the consequence of the boson condensation as described in the framework of spontaneous symmetry breakings (SSB). The switch from a still semi-classical Quantum Mechanical (QM) in the 1st quantization to a Quantum Field Theory (QFT) view embedded in the 2nd quantization is advocated for a more realistic and authentic description of water, condensed matter and living systems.

This article addresses the need to know the thermal conductivity in different filaments that this FDM technology uses. Because there are multiple applications that these additive manufacturing products play in the field of thermal insulation. For the study of thermal conductivity, the DTC-25 commercial conductivity measurement bench is used, where the tests will be carried out on a set of seven different materials with 100% fabrication density. From base materials such as acrylonitrile butadiene styrene (ABS) or polylactic acid (PLA), materials of high mechanical and thermal resistance, polyether ether ketone (PEEK) and high-performance polyetherimide thermoplastic (ULTEM), to materials with metal inclusions (aluminum 6061) that would later be subjected to thermal aftertreatments. The study shows how the parts manufactured with aluminum inclusion have a higher thermal conductivity, 0.40 ±0.05 W/m·K, compared to another material, such as TPU, of high mechanical and thermal resistance, with a conductivity of 0.26 ±0.05 W/m·K.

In this paper, the effect of microstructure on the thermal conductivity of plasma-sprayed Y₂O₃ stabilized ZrO₂ (YSZ) thermal barrier coatings (TBCs) is investigated. Nine freestanding samples deposited on aluminum-base superalloy are studied. Cross-section morphology such as pores, cracks, m-phase content, grain boundary density of the coated samples are examined by scanning electron microscopy (SEM) and electron back-scattered diffraction (EBSD). Multiple linear regressions are used to develop quantitative models which describe the relationship between the particle parameters, m-phase content and the microstructure such as porosity, crack-porosity, the length density of small-angle-crack and the length density of big-angle-crack. Moreover, the relationship between microstructure and thermal conductivity is investigated. Results reveal that the thermal conductivity of the coating is mainly determined by the microstructure and grain boundary density at room temperature (25 ℃) and by the length density of big-angle-crack, monoclinic phase content and grain boundary density at high temperature (1200 ℃).

Polymer nanocomposites are composed of polymer materials reinforced with nano fillers. In the present study the effective thermal conductivity of the composites filled with nanofillers has been investigated using commercially available finite element software ABAQUS 6.11. The nanofillers used were alumina particles and multi-walled carbon nanotubes (MWNTs) and the matrix was considered to be made of epoxy. For the analysis 2D and 3D Representative Volume Elements (RVEs) were generated using Random Sequential Adsorption (RSA) algorithm using MATLAB and Python scripts. Thermal conductivity was found out for 2D and 3D RVEs for different area and weight fractions respectively. Two different shapes of the alumina nanoparticles were considered: spherical (circular) and ellipsoidal (elliptical) for 3D (2D) analysis. It was found that the thermal conductivity was increased with the addition of nanofillers. The increase in thermal conductivity was approximately same for both types of inclusions at corresponding area or weight fractions in 2D or 3D analysis. The results showed that addition of MWNTs to the composites lead to a significant increase in thermal conductivity than spherical or ellipsoidal inclusions.

Thermal interface material (TIM) that can exist as liquid at the service temperature enables efficient heat transfer across two adjacent surfaces in electronic applications. In this work, the thermal conductivities of different phase regions in the Ga-In system at various compositions and temperatures are measured for the first time. A modified comparative cut bar technique is used for the measurement of the thermal conductivities of In_xGa_1-x (x=0, 0.1, 0.214, 0.3, and 0.9) alloys at 40, 60, 80, and 100^oC that are the temperatures commonly encountered in consumer electronics. The thermal conductivity values for the liquid and semi-liquid (liquid+β) Ga-In alloys are higher than the TIM currently used in consumer electronics. These measured quantities, along with the available experimental data from the literature, served as input for the thermal conductivity parameter optimization using the CALPHAD (CALculation of PHase Diagram) method for the pure elements, solution phase, and two-phase region. A set of self-consistent parameters for the description of the thermal conductivity of the Ga-In system is obtained. There is good agreement between the measured and calculated thermal conductivity values for all the phases. Hence, it can be envisaged that liquid/semi-liquid Ga-In alloys can be considered as a potential TIM in consumer electronics due to its high thermal conductivity.

Flexibility of polymers defined by an equation in 2019 is related here to thermal conductivity, using reliable data for both properties found in the literature. The resulting equation is simple, it has the form of a quadratic polynomial. The goodness of the fit represented by R² = 0.975, while R² = 1 represents a perfect fit. Thus, knowledge of one of these properties can be used for calculation of the other one. The present results are a part of a larger program enabling obtaining by calculation pertinent properties of polymers from other properties for which data are available.

Accumulative roll bonding (ARB) is one of methods of severe plastic deformation which is relevant for industrial production of sheets. While mechanical properties of several magnesium alloys subjected to ARB process have been studied, the physical properties have been reported only for some magnesium alloys. These properties are influenced by the texture developed during the ARB process and the temperature load. In the presented contribution, we studied thermal diffusivity and thermal conductivity of an AZ31 magnesium alloy after 1 and 2 passes through the rolling mill. Thermal diffusivity was measured with the laser-flash method in the temperature range between 20 and 350 °C. Thermal conductivity depends on the number of rolling passes. The microstructure and texture of sheets are significant factors influencing the thermal properties.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

A study on the dependence of the thermal conductivity of the percolation network of carbon nanotubes (or CNTs) on the type and degree of functionalization has been carried out. The study was focused on the influence of the more commonly used -COOH, -OH and -СОNH2 groups. A non-linear dependence of the conductivity on the number of functional groups has been revealed. A small number of functional groups can improve conductivity, and a large one can impair it. We presuppose the existence of competing processes that increase thermal conductivity (changes in the CNT geometry, improvement of the contact between them) and enhance photon scattering (emergence of defects and scattering centers). The data can be used for controlling the thermophysical properties of the CNTs as well as determining the optimal degree of functionalization during the development of composites and nanodevices.

The internet of things and growing demand for smaller and advanced devices has created the problem of high heat production in the electronic equipment which greatly reduces the work performance and life of the electronic instruments. Thermal interface materials (TIMs) are placed in between heat generating micro-chip and the heat dissipater to conduct all the produced heat to the heat sink. Development of suitable TIMs with excellent thermal conductivity (TC) in both in-plane and through-plane directions is a very important need at present. For efficient thermal management, polymer composites are potential candidates. But in general their thermal conductivity is low compared to that of metals. The filler integration into the polymer matrix is one of the two approaches used to increase the thermal conductivity of polymer composites and is also easy to scale up for industrial production. Another way to achieve this is to change the structure of polymer chains, which fall out of the scope of this work. In this review, considering the first approach, the authors have summarized recent development in many types of fillers with different scenarios by providing multiple cases with successful strategies to improve through-plane thermal conductivity (TPTC) (K⊥). For better understanding of TC the comprehensive background is also presented. In the end, it is given a detailed conclusion which provides drawbacks of some filler, multiple significant routes recommended by other researchers to build Thermally Conductive Polymer Composites, future aspects along with direction so that the researchers can get a guideline to design an effective polymer based Thermal interface materials. A number of methods to improve the effective (out-plane) thermal conductivity of polymer composites are also discussed.

Efficient thermal management of modern electronics requires the use of thin films with highly anisotropic thermal conductivity. Such films enable the effective dissipation of excess heat along one direction while simultaneously providing thermal insulation along the perpendicular direction. In this study, we investigate the thermal conductivity of bilayer graphene (BLG) sheets using non-equilibrium molecular dynamics, examining both in-plane and cross-plane thermal conductivities. The in-plane thermal conductivity of 10 nm × 10 nm BLG with zigzag and armchair edges at room temperature is found to be around 204 W/m.K and 124 W/m.K, respectively. The in-plane thermal conductivity of BLG increases with sheet length. For all sizes, BLG with a zigzag edge exhibits higher thermal conductivity than that of the armchair edge, with this difference becoming more pronounced as the lengths of the sheets increase. In addition, increasing temperature from 300 K to 600 K decreases the in-plane thermal conductivity of a 10 nm× 10 nm zigzag BLG by about 34%. Similarly, the application of a 12.5% tensile strain induces a 51% reduction in its thermal conductivity compared to the strain-free values. Armchair configurations exhibit similar responses to variations in temperature and strain, but with less sensitivity. Furthermore, the cross-plane thermal conductivity of BLG at 300 K is estimated to be 0.05 W/m·K, significantly lower than the in-plane results by approximately four orders of magnitude. The cross-plane thermal conductance of BLG decreases with increasing temperatures, specifically, at 600 K, its value is almost 16% of that observed at 300 K.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

In recent years, it has been found in engineering practice that the service life of cemented carbide shield machine tools used in uneven soft and hard strata is substantially reduced. The study found that thermal stress is the main reason for the failure of cemented carbide shield tunneling tools when shield tunneling is carried out in uneven soft and hard soil. To maintain the hardness of cemented carbide, improving the thermal conductivity of the shield machine tool is of great importance for prolonging its service life and reducing engineering costs. In this paper, graphene and carbon nanotubes were mixed with WC-Co powder and sintered by SPS (Spark Plasma Sintering). The morphology was observed by using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). A Rockwell hardness tester and bending strength tester were used to test hardness, bending strength and thermal conductivity. The results show that adding trace graphene or carbon nanotubes can increase the bending strength of the cemented carbide by approximately 50% while keeping the hardness of the cemented carbide unchanged. The thermal conductivity of the cemented carbide can be increased by 10% with the addition of 0.12% graphene alone.

In this paper, an icosahedral non – body centered model to simulate the periodic structure of homogeneous particulate composites, by predicting the particle arrangement, is presented. This model has yielded three different variations which correspond at three different deterministic particle configurations. In addition, the concept of boundary interphase between matrix and inclusions was taken into account. Thus, the influence of particle vicinity was examined in parallel with the interphase concept on the thermomechanical properties of the overall material. Next, by the use of this model the authors derived a closed – form expression to estimate the thermal conductivity of this type of composites. To test the validity of the model, the theoretical values arising from the proposed formula were compared with other theoretical predictions obtained from several accurate formulae found in the literature and an adequate accordance was observed.

The thermal conductivity of the products of the interaction of molten core with concrete was derived using number theory. A formula has been found that describes the thermal conductivity of ZrO₂, ZrSiO₄, (U,Zr)SiO₄ and UO₂ over a wide temperature range. Formula is expressed in terms of the atomic numbers of elements, their valencies, the crystal structure of substances, and the thermal conductivities of individual chemical elements of the corium.

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

Using number theory, a formula is obtained that describes the thermal conductivities of ZrC, UC, UN, ThN, ZrN and Th_xU_1-xN at x = 0.2 and 0.5 with temperature change. This formula contains the atomic numbers of the elements, the thermal conductivities of the individual elements of the substance, and the structural parameter. There is no direct dependence on temperature in the formula, since it is hidden in the thermal conductivities of each element and in the structure parameter. In some temperature ranges, the structural parameter is constant; therefore, the thermal conductivity of some carbides and nitrides is expressed through summing the thermal conductivities of individual elements.

Media thermal conductivity is important in various heat-transfer processes. Many conventional fluid conductors suffered low conductivity and environmental issues. Therefore, researchers developed efficient aqueous nanofluid conductors. Carbon nanotubes (CNTs) are widely studied to reach efficient, stable, low-cost and environmentally-friendly aqueous-nanofluids. This review provides a clear understanding of how CNTs improve thermal conductivity of aqueous nanofluids. A qualitative model is presented to explain literature mechanisms behind improvement. CNT type effects are discussed with other factors such as aspect ratio, Reynold number, dispersion quality, composition, temperature and additives. CNT functionalization is described. Relations to estimate nanofluid thermal conductivity are discussed. The model will help specialists to tailor CNT aqueous nanofluids as desired.

The manuscript reported the synthesis of Al2O3 nano-coating onto quartz fiber by plasma electrolysis spray for enhanced thermal conductivity and stability. The nano- and micro-sized clusters were partially observed on the coating, while most coating was relatively smooth. It was suggested that the formation of a ceramic coating was followed as the nucleation-growth raw, that is, the formation of the coating clusters was dependent on the fast grow-up partially, implying the inhomogeneous energy distribution in the electrolysis plasma. The deposition of the Al2O3 coating increased the annealing tensile strength from 19.2 MPa to 58.1 MPa. The thermal conductivity of the coated quartz fiber was measured to be 1.17 W m-1 K-1, increased by ~45% compared to the bare fiber. The formation mechanism of the Al2O3 coating was preliminarily discussed. We believe that the thermally conductive quartz fiber with high thermal stability by plasma electrolysis spray will find a wide range of applications in industries.

Copper mine tailings are the residual products after the purification of precious copper from copper ores, and their storage can create numerous environmental problems. Many researchers have used copper mine tailings for preparation of geopolymer. This paper studies the enhancement of the cementitious activity of copper mine tailings in geopolymer system. First, copper mine tailings are activated through a mechanical grinding activation. Afterward, the mechanically activated copper mine tailings are further processed through thermal activation and alkaline roasting activating. The cementitious activity index of copper mine tailings is characterized through the degree of concentration of alkali leaching silicon and aluminum. It was observed that the Si and Al alkali leaching concentration of mechanical activated tailings was increased by 26.03% and 93.33%, respectively. The concentration of Si and Al was increased by 54.19% and 119.92%, respectively. For alkaline roasting activating, roasting time, temperature and (C/N ratio) were evaluated through the orthogonal test, and the best condition was activation for 120 min at 600℃ with C/N ratio is 5:1. In this study, the SEM, XRD and IR analysis show that mechanically activation, thermal activation and alkaline roasting activating can improve the cementitious activity index of copper mine tailings.

Experimental measurement of porous polypropylene (PP) using the DTC-25 TA laboratory equipment and hot box test has been compared. The thermal conductivity of materials indicates the insulation capability of building materials. Excellent building materials will have a lower thermal conductivities value as well as other building insulator performance metrics. While results show that increasing the volume fraction of fluid in the porous PP has an inverse association with the thermal conductivity of the material as predicted by porous media theories, there is a marked difference in the measured values of the thermal conductivity using the two methods. The thermal conductivity values of porous from DTC-25 and hot box test were 0.21 and 0.0033 W/mK, respectively. The difference in the thermal conductivity values was due to the misapplication of the Fourier’s guarded heat flow model in the DTC-25 device to a convective fluid porous medium material.

in order to enhance the separation performance and to reduce the heat loss of the transmembrane for membrane distillation, the thermal efficiency and hydrophobicity of the membrane distillation should be simultaneously enhanced. In this work, a PVDF/PET hydrophobic/hydrophilic membrane is prepared by non-solvent phase inducing method. Nanosized silica aerogel (SiAG) with high porosity is added to the composite membranes. The modifying effects and operating conditions on permeate flux and thermal efficiency in direct contact membrane distillation (DCMD) are investigated. Furthermore, the latent heat of vaporization and the heat transfer across the membranes are compared for SiAG addition, which indicates that the composite PVDF@SiAG/PET membranes display a great potential for distillation-separation application with high heat efficiency.

Due to the complexity of the microstructure of porous media, it is of great significance to explore the heat transport mechanism in porous media in many engineering applications. In this study, an expression for effective thermal conductivity（ETC） of porous media with randomly distributed damaged tree-like bifurcation networks is derived based on the theory of thermodynamics and fractal features of tree-like bifurcation networks. We investigate the effect of heat conduction and heat convection in porous media with randomly distributed damaged tree-like bifurcation networks on the ETC of the porous media. It is found that our fractal model is in good consistency with the existing available experimental data. In addition, the influence of the micro-structural parameters of the model on heat transfer in the porous media have been analyzed in detail. The research results can provide significant theoretical guidance for the development and design of heat transfer systems.

Theory of the Thermal Response Testing (TRT) is a well-known part of sizing process of the geothermal exchange system. Multiple parameters influence accuracy of effective ground thermal conductivity measurement; like testing time, variable power, climate interferences, groundwater effect etc. To improve accuracy of the TRT we introduced procedure to additionally analyze falloff temperature decline after power test. Method is based on a premise of analogy between TRT and petroleum well testing, since origin of both procedures lies in diffusivity equation with solutions for heat conduction or pressure analysis during radial flow. Applying pressure build-up test interpretation technique to the borehole heat exchanger testing, greater accuracy could be achieved since ground conductivity could be obtained from this period. Analysis was conducted on coaxial exchanger with five different power steps, and with both direct and reverse flow regime. Each test was set with 96hr of a classical TRT, followed by 96hr of temperature decline, making it almost 2000 hours of cumulative borehole testing. Results showed that ground conductivity value could vary as much as 25% depending on test time, seasonal period and power fluctuations while thermal conductivity obtained from a falloff period gives more stable values with only 10% value variation.

The objective of the prototype is to eliminate the polluting contamination of water sources, due to the leak of industrial waste without any kind of treatment, mainly generated by the industries and home sector. In this project, a prototype of water purification by plasma technology has been designed. The prototype will convert contaminated water into the plasma stream and eliminate the pathogens from the water by exposing it to ultraviolet radiation and plasma sterilisation. The polluted water will be accelerated at high speed using a water pump in order to convert it into a liquid-gas mixture for ease plasma generation. This process will be achieved when the electric supply from a source of alternating current (AC) is applied to the water by means of high voltage electrodes. After which, the mixture slows down to return into liquid form and the clean water is obtained. The whole process takes place without significantly raising the temperature also knows as non-thermal plasma. The device also has an automatic flow and pressure control system. Finally, a short feasibility study has been conducted on the water samples collected and report obtained from Chennai Metropolitan Water Supply and Sewage boards are reported. It has been concluded that this new plasma-based water treatment system will be more efficient and cheaper than the current wastewater treatment techniques and can be used in the future as the replacement of current secondary and tertiary treatments of industrial wastewater.

In this experimental report the biocompatibility of elastomeric scaffold structures made via stereolithography employing table-top 3D printer (Ember, Autodesk) and commercial resin FormLabs Flexible (FormLabs) was studied. The samples were manufactured using standard printing and development protocol, which is known to inherit cytotoxicity due to remaining non-polymerized remaining monomers, despite the polymerized material being fully biocompatible. Additional steps were taken to remedy this problem: the fabricated structures were soaked in isopropanol and methanol for different conditions (temperature, duration) in order to leach out the non-polymerized monomers. Also printed structures were UV exposed to assure maximum polymerization degree of the material. Post-processed structures were seeded with myogenic stem cells and the number of live cells was evaluated as an indicator for the material biocompatibility. The straightforward post-processing protocol enhances the biocompatibility by 7 times after 7 days soaking in isopropanol and methanol and is comparable to control (glass and polystyrene) samples. This proposes the approach as a novel and simple method to be widely applicable for dramatic cytotoxicity reduction of optically 3D printed micro-/nano-scaffolds for biomedical applications.

The research work explores the impact of temperature on Silicon photovoltaic (PV) panels considering Nigeria as case study. It is found that high solar radiation in Nigeria increases surface temperature of PV panel above 25oC of optimal operating temperature of PV panels. Redundant energy gain from incident solar energy is dissipated at the rear of PV panels as heat, which reduces the efficiency of PV panel. Cooling mechanism is needed to cool the PV panels to increase the efficiency. In this study we demonstrated a unique design of a bifunctional photovoltaic-thermal (PVT) system by employing heat exchanger at the rear of PV panel and water is used as a working fluid that is circulated through the heat exchanger to remove the excess heat. It is observed from the simulation results that Maiduguri peak annual electrical power output gives 1907kWh/kWp which is the highest, because of high solar radiation average of 727W/m2 in a year. And for Makurdi the peak annual electrical power output of 1542kWh/kWp while for Port Harcourt the peak power output of 1355kWh/kWp respectively. Interestingly, Polycrystalline Si-PV surface temperature decrease from 49.25oC to 38.38oC. Electrical power increased from 1526.83W to 1566.82W in a day and efficiency increase from 13.99% to 15.01%.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

Modelling water vapour flow, heat transfer and porosity in porous adsorbent is somewhat challenging simulation problem. Primary macroscopic water vapour flow models, such as Darcy's law, fail to predict the pressure drop entirely correctly for the reason that many of flow parameters not considered because of the simplifications that remain made for the multi-scale structure of the porous adsorbents. For one to develop a good physical understanding of such water vapour flows and the accuracy of existing 3D simulation models, there is a need for some accurate 3D geometry to be studied. This present work describes two-phase water vapour flow and adsorption/ desorption performed on porous adsorbent by a Dynamic vapour sorption (DVS). The CFD simulation results are associated with experiments results. It is decided that for such complex porous adsorbent CFD simulation problems the use of COMSOL Multiphysics and SolidWorks flow simulation will be utilised.

In this paper, the experimental results of the thermal sub-system of a reliable and cost-effective polygeneration solar system are presented. This polygeneration system produces heating, cooling and electricity from solar energy, which are used in an existing test-building. Heat is generated in four evacuated tube solar collectors (ETC). The heat may be used for space cooling, through a variable geometry ejector (VGE) heat pump. In order to reduce the mismatches between generation and consumption, two thermal storage tanks were added. The performance of a new thermal storage, with 400 l, able to storage both sensible and latent heat, was tested. Heating performances of the test-building were assessed. Ejector cycle tests were also performed.

Based on PVDF (piezoelectric sensing techniques), this paper attempts to study the propagation law of shock waves in brittle materials during the process of three-wavelength laser irradiation of polysilicon, and discusses the formation mechanism of thermal shock failure. The experimental results show that the vapor pressure effect and the plasma pressure effect in the process of pulsed laser irradiation lead to the splashing of high temperature and high density melt. With the decrease of the laser wavelength, the laser breakdown threshold decreases and the shock wave is weakened. Because of pressure effect of the laser shock, the brittle fracture zone is at the edge of the irradiated area. The surface tension gradient and surface shear wave caused by the surface wave are the result of coherent coupling between optical and thermodynamics. The average propagation velocity of laser shock wave in polysilicon is 8.47×103m/s, and the experiment has reached the conclusion that the laser shock wave pressure peak exponentially distributes attenuation in the polysilicon.

The cell case temperature versus time profiles of a multistage fast charging technique (4C-1C-CV)/fast discharge (4C) in a 2.3 Ah cylindrical lithium-ion cell are analyzed using a 1D thermal model. Heat generation is dominated by the irreversible component associated to cell overpotential, although evidences of the reversible component are also observed, associated to the heat related to entropy from the electrode reactions. The final charging stages (i.e., 1C-CV) significantly reduce heat generation and cell temperature during charge, resulting in a thermally safe charging protocol. Cell heat capacity was determined from cell specific heats and cell materials thickness. The 1D model adjustment of the experimental data during the 2 min. resting period between discharge and charge allowed us to calculate both the time constant of the relaxation process and the cell thermal resistance. The obtained values of these thermal parameters used in the proposed model are almost equal to those found in the literature for the same cell model, which suggests that the proposed model is suitable for its implementation in thermal management systems.

Droughts occurring more and more frequently in recent years are usually associated with progressive climate changes. Modern monitoring methods is mainly associated with agricultural use due to the high market demand for services protecting against agricultural losses. In natural wetland ecosystem this problem is neglected which is probably due to fact that this are ecosystems rich in water by definition. Nevertheless this droughts might become a problem of wetlands, whose good condition depends on adequate hydration. Therefore this study focused on determination Crop Water Stress Index (CWSI) for natural heterogeneous wetland habitats. CWSI based on remotely sensed land surface temperature and associated basic meteorological (air temperature and humidity) measurements. CWSI was calculated based on high resolution LST measurements from UAV platform and compare with on ground measurements of soil moisture, CCI, fAPAR and meteorological conditions. Results shows that CWSI properly shows water condition of plants in measured habitats and revels high importance of metrological conditions during data acquisition.

In this study, fibers were extracted from different parts of the okra plant (Abelmoschus esculentus) via water- and dew-retting methods. The fibers were subjected to physical and thermal analyses. The fibers obtained from the upper part of the okra plant show higher breaking strength and lower linear density. Fibers obtained via water-retting exhibited higher breaking strength, elongation at break rates, and lower linear density values. The paper also presents the results of thermogravimetric analysis of the okra fibers. Tests were carried out in oxygen and inert gas atmospheres. The temperature range of the main thermal decomposition stage was in the 275–400°C for range thermo-oxidation and 300–425°C for pyrolysis investigation. Slight differences were found in the thermal resistances of the tested fibers, which was confirmed by an analysis using the alpha s- alpha r methodology. The calculated activation energy values show a large-spread range.

With permafrost degenerating caused by climate change, water accumulation increases in permafrost regions during last decades. Water accumulation will deteriorate existing status of engineering in cold regions. Water accumulation can make a thermal effect on permafrost under construction, even result in failure of the subgrade. Moreover, the thermal effect is related to water temperature. However, temperature variation of water accumulation is complex, and its influence factors include air temperature, environment, scope of water accumulation and so on. In order to make analysis of the damage mechanism of water accumulation on permafrost, it is necessary to explore the internal temperature change of water accumulation. This paper proposes a review about temperature calculation method of water accumulation in cold environment. The thermal calculation method between air and water boundary of water accumulation is summarized. Water temperature change of water accumulation with various type is analyzed. The thermal calculation considering phase transformation in water accumulation is discussed, and heat transfer from the bottom of water accumulation to the underlying soil is further studied. Finally, the key factors which are advantageous to make research about the thermal effect of water accumulation in permafrost is proposed to optimize calculation method.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

Shale gas production is associated with significant usage of fresh water and discharge of wastewater. Consequently, there is a necessity to create the proper management strategies for water resources in shale gas production and to integrate conventional energy sources (e.g., shale gas) with renewables (e.g., solar energy). The objective of this study is to develop a design framework for integrating water and energy systems including multiple energy sources, cogeneration process, and desalination technologies in treating wastewater and providing fresh water for shale gas production. Solar energy is included to provide thermal power directly to a multi-effect distillation plant (MED) exclusively (to be more feasible economically) or indirect supply through a thermal energy storage system. Thus, MED is driven by direct or indirect solar energy, and excess or direct cogeneration process heat. The proposed thermal energy storage along with the fossil fuel boiler will allow for the dual-purpose system to operate at steady-state by managing the dynamic variability of solar energy. Additionally, electric production is considered to supply a reverse osmosis plant (RO) without connecting to the local electric grid. A multi-period mixed integer nonlinear program (MINLP) is developed and applied to discretize operation period to track the diurnal fluctuations of solar energy. The solution of the optimization program determines the optimal mix of solar energy, thermal storage, and fossil fuel to attain the maximum annual profit of the entire system. A case study is solved for water treatment and energy management for Eagle Ford Basin in Texas.

Abstract: Currently, thermal power is the largest source of power in the world. Although the impacts of climate change on cooling water sufficiency in thermal power plants have been extensively assessed globally and regionally, their economic consequences have seldom been evaluated. In this study, the Asia-Pacific Integrated Model Computable General Equilibrium model (AIM/CGE) was used to evaluate the economic consequences of projected future cooling water insufficiency on a global basis, which was simulated using the H08 global hydrological model. This approach enabled us to investigate how the physical impacts of climate change on thermal power generation influence economic activities in regions and industrial sectors. To account for the uncertainty of climate change projections, five global climate models and two representative concentration pathways (RCPs 2.6 and 8.5) were used. The ensemble-mean results showed that the global gross domestic product (GDP) loss in 2070–2095 due to cooling water insufficiency in the thermal power sector was −0.21% (−0.12%) in RCP8.5 (RCP2.6). Among the five regions, the largest GDP loss of −0.57% (−0.27%) was observed in the Middle East and Africa. Medium-scale losses of −0.18% (−0.12%) and −0.14% (−0.12%) were found in OECD90 (the member countries of the Organization for Economic Co-operation and Development as of 1990) and Eastern Europe and the Former Soviet Union, respectively. The smallest losses of −0.05% (−0.06%) and −0.09% (−0.08%) were found in Latin America and Asia, respectively. The economic impact of cooling water insufficiency was non-negligible and should be considered as one of the threats induced by climate change.

Thermal-expandable microcapsules (TEMs) for water-based coatings were synthesized with co-polymer of Acrylonitrile (AN) - Methyl methacrylate (MMA) - Ethylhexyl acrylate (EHA) - Divinylbenzene (DVB) as shell and toluene-p-sulfonyl hydrazide as core by suspension polymerization method. It was found that the microcapsules with desirable thermal expansion property and good heat stability could be obtained with a shell monomers composition of 70% AN /20% MMA /9% EHA /1% DVB. When 2% styrene-maleic acid copolymer (SMC) as emulsifier and 3% poly (vinyl pyrrolidone) (PVP) as dispersing agent were used, well defined spherical and more uniform microcapsules could be prepared. It was also found that when the shell/core mass ratio was 3:1, an encapsulation efficiency of ca. 94.5% could be achieved. Beyond this ratio, the increase of encapsulation efficiency reached a plateau. The 100 μm thickness film of water-based coating containing 5% microcapsules could be expanded to the thickness of 450 μm after exposed at 150 °C for 2 minutes. TG analysis revealed the mass loss start temperature of coating increased by more than 30 °C when 5% microcapsules were added to water-based coatings, which demonstrated the flame-retardant function of the coatings.

In this work commercial 18650 lithium-ion cells with LiMn₂O₄, LiFePO₄ and Li(Ni_0.33Mn_0.33Co_0.33)O₂ cathodes were exposed to external heating in an Accelerating Rate Calorimeter (es-ARC, THT Company) to investigate the thermal behavior under abuse conditions. New procedures for measuring external and internal pressure change of cells were developed. The external pressure was measured utilizing a gas-tight cylinder inside the calorimeter chamber in order to detect venting of the cells. For internal pressure measurements, a pressure line connected to a pressure transducer was directly inserted into the cell. During the thermal runaway experiments, three stages (low rate, medium rate and high rate reaction) have been observed. Both pressure and temperature change indicated different stages of exothermic reactions, which produced gases or/and heat. The onset temperature of thermal runaway was estimated according to temperature and pressure changes. Moreover, the different activation energies for the exothermic reactions could be derived from Arrhenius plots.

This study investigates the land surface temperature (LST) distribution from thermal infrared data for analyzing the characteristics of surface coverage using the Vegetation-Impervious-Soil (VIS) approach. A set of ten images, obtained from Landsat-5 Thematic Mapper, between 2001 and 2010, were used to study the urban environmental conditions of 47 neighborhoods of Porto Alegre city, Brazil. Porto Alegre has had the smallest population growth rate of all 27 state capitals in the last two decades in Brazil, with an increase of 11.55% in inhabitants from 1,263 million in 1991 to 1,409 million in 2010. We applied the environmental Kuznets curve (EKC) theory in order to test the influence of the economically-related scenario on the spatial nature of social-environmental arrangement of the city at neighborhood scale. Our results suggest that the economically-related scenario exerts a non-negligible influence on the physically driven characteristics of the urban environmental conditions as predicted by EKC theory. The linear inverse correlation R2 between household income (HI) and LST is 0.36 and has shown to be comparable to all other studied variables. Future research may investigate the relation between other economically-related indicators to specific land surface characteristics.

The thermal degradation behaviour of 10:90 and 90:10 blends of Polyethylene Terephthalate (PET) and petroleum coke has been investigated using mechanical alloying (milling) at 300 rpm and for periods up to 1-10 hours. Milled specimens were characterised using SEM and x-ray diffraction; their thermal degradation behaviour was investigated using thermo-gravimetric analyser (TGA) for temperatures up to 1200°C. Whereas PET specimens showed a tendency towards flattening out and increased surface area during collisions in ball mills, petroleum coke particles tended to break down into smaller particles. 10:90 and 90:10 blends of PET and coke showed significant microstructural evolution with increasing speeds and time including fracture, strain hardening and re-welding. X-ray diffraction results showed clear evidence for increasing amorphous component in petroleum coke without much influence on PET crystallinity. Thermo-gravimetric results showed a significant increase in the overall degradation and much higher weight losses associated with mechanical alloying. This study has shown that mechanical alloying could be used to modify the degradation behaviour of coke/plastic blends and corresponding yield during pyrolysis with implications for plastic waste management.

The development of offshore wind farms requires robust bonding solutions that can withstand harsh marine conditions for the easy integration of secondary structures. This paper investigates the durability performance of two adhesives: Sikadur 30 adhesive and Loctite UK 1351 B25 for use in offshore wind environments. Tensile tests on adhesive samples and accelerated aging tests were carried out under a variety of temperature and environmental conditions, including both dry and wet conditions. The long-term effects of aging on adhesive integrity are investigated by simulating the operational life of offshore installations. The evolution of mechanical properties, studied under accelerated aging conditions, provides an important indication of the longevity of structures under normal conditions. The results show significant differences in performance be-tween the two adhesives, highlighting their suitability for specific operating parameters. It should also be noted that for both adhesives, their exposure to different environments (seawater, distilled water, humid climate) over a prolonged period has shown that i) Loctite adhesive has a slightly faster initial uptake than Sikadur adhesive, but the later reaches an asymptotic plateau with a lower maximum absorption rate than Loctite adhesive; and ii) a progressive deterioration in the tensile properties following an exponential function. Therefore, aging behavior results showed a clear correlation with Arrhenius' law, providing a predictive tool for the aging process. Thus, the aging process of the two adhesives follows Arrhenius kinetics.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

Every simplification has the potential to add a systematic error to the measured value. Sometimes, the addition does not render the measurement useless. In the case of oil well flow measurements based on the thermal properties of the fluid in the well, the addition of a systematic error of up to 20% can occur if the variation in the internal energy of the fluid and, most importantly, the transient nature of heat transfer in the completion are not taken into account. This error is a mathematical consequence of the simplifications chosen. To work within the first hours of good operation, given the need for immediate application in a prototype water injection well developed and installed at the UFRN, this article presents an analytical solution for calculating the flow rate by solving the differential equations obtained by applying the principles of mass and heat transfer. As a result, at the cost of greater complexity, the systematic error drops to values of less than 1% in the first two hours of operation of the well, as seen throughout this document.

The problem of water drinking supply is very important in the world, especially for developing countries, in particular Algeria. In this work we propose to study a distillation system based on solar energy process using an artificial intelligence approach in order to enhance the performance and the daily production. For this purpose, a conventional solar still and capillary film solar still was used. The operating parameters of the two distilleries are analyzed and the neural network approach was used to predict the performance through the amount of distillate, solar radiation and ambient temperature. The sensitivity between the operating parameters of the solar still for two case have been studied through the artificial neuron network model. The obtained results are promising, analyzed and discussed.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

Black soldier fly larvae (BSFL) can use food by-products or residues as a growth substrate, and their use is considered a strategic solution to improve the sustainability and efficiency of animal production. BSFL need to be reared under controlled environmental conditions, as temperature can affect the welfare of the larvae and the efficiency of their bioconversion. The goal of this experiment was to test different diets: control, vegetable, carnivorous, omnivorous and to assess their effect on larval growth performance, chemical composition, and substrate temperature. BSFL (6-days-old) were randomly selected and allocated to one of the four diets for the entire experiment (8 days). The temperature in each container was measured twice daily using a thermal imaging camera. The vegetable diet led to significantly lower growth performance (p

This article provides insight into flow measurement techniques in water injection wells in oil production fields, with a particular focus on the initial phases of operation. Consequently, the method created by Ramey in 1962, originally intended for estimating the temperature of the injection fluid, has been adapted to calculate the flow rate. In this technique, the calculation This procedure is based on the correlation between the thermal flux formed in the well. The discrepancy between the temperatures of the injected liquid and the geothermal temperature of the reservoir is the main source of the systematic errors in Ramey’s technique. To a lesser extent, but still significant, failure to observe the injection time in a fluid variation also results in an error problem that needs the failure to adhere to the scheduled injection time for a fluid alteration also yields a notable error dilemma that needs to be fixed. The reduction of listed systematic errors is the product of the main part of this article.

Utilizing NCEP/NCAR monthly reanalysis data alongside precipitation observations from 1936 monitoring stations across China spanning from 1966 to 2022, this study establishes a location index for the thermal low-pressure center situated over the Qinghai–Tibet Plateau. Temporal variations in the location index and summer (July) precipitation patterns in China were studied. Over the past six decades, thermal low-pressure centers have been predominantly positioned near 90°E and 32.5°N on the plateau, with their distribution extending from east to west rather than from south to north. The longitudinal and latitudinal position indices exhibit contrasting linear trends, with a positive trend observed during the 1970s and early 21st century and a negative trend in subsequent decades. Mutation analysis highlights pronounced weakening mutations occurring in 1981 and 1973, with the longitudinal index transitioning from an inter-annual cycle of approximately 6-8 years, while the latitudinal index displays quasi-cyclic oscillations of 5 and 8 and 12-14 years. Strong negative correlations are evident between the location indices and precipitation along the southeastern edge of the Qinghai–Tibet Plateau and in Southern China, contrasting with the positive correlations observed in the central-eastern plateau, northwest China, North China, and the Huang-Huai region. The influence of southerly airflow predominates over much of China east of the plateau, while northwest China experiences convergence between northerly and southerly airflow. Higher location indices correspond to weaker surface cold air masses and strengthened Western Pacific Subtropical and South Asian Highs south of the Yangtze River Basin, resulting in significantly reduced rainfall in the southern Yangtze River region and increased rainfall in northwest China.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

Two heating surfaces with longitudinal fins are located within the closed channel inside the housing made of thermal insulation material. The air flow inside the channel was carried out by an axial fan. The heating of the fins is established by using two positive temperature coefficient heating elements (PTC). Air flows circularly from one finned surface to another, and after reaching the required temperature, it leaves the housing. In the heating system conceived in this way, a methodology based on transient thermal irreversibility of heating sources and circular air flow has been established. Volumetric air flow and circulation time within the channel were varied. The total entropy generated does not include hydraulic irreversibility, but transient thermal irreversibility of the air and heat sources. For conducting analytical modeling, the temperature of the PTC heater was considered constant at 423K and 473K. Volumetric air flow varied in the interval from 0.00001m3s-1 to 0.00006m3s-1. The experimental determination of the transient thermal entropy was performed at a much higher air flow rate of 0.005m3s-1 inside the closed channel. Due to the continuous increase in air temperature, the temperatures of both PTC heaters increased within the examined time interval of 300s. According to experimental testing, the total transient thermal entropy of the described heating system has a minimum after 175s from the start of the circular heating of the air. The minimum of transient entropy also implies the optimal time of channel opening and exit of heated air.

Almost all single-family detached house in Canada consume huge electricity for space heating and domestic hot water (DHW) purposes. There are many possibilities to design an energy-efficient house. A solar water heating system can be used for domestic water and space heating. Water temperature can be kept constant always by connecting a heat pump or oil burner because solar energy is intermittent. Proper and optimized solar photovoltaic and collector design, tank design, heat pump selection, house insulation, total demand calculation in each section are essential. Energy-Efficient house design has been proposed with water heating and space heating system and compared with the existing system, solar PV based systems, and solar collector based system. The tracking and non-tracking based solar thermal collector based and the solar photovoltaic based system has been compared in this paper and investigate the suitable one for practically applicable and acceptable by the people. Simulation has been done by using the PolySun software. It found that by implementing the proposed PV based system with tracking is highly suitable considering lower cost, high output power, flexibility, easy installation.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

The research carried out concerned the laboratory assessment of the applicability of the Crop Water Stress Index (CWSI) as a practical tool for assessing the risk of desiccation for selected wetland habitats: transition mires and quaking bogs as well as alkaline fens. The analysis was carried out on 3 soil samples with a vegetation cover (with the dimensions of 40×40×30 cm) collected during the full vegetation season for each mentioned habitat, with a characteristic species composition. Experimental research was carried out between 17^th May 2018 and 19^th June 2018. Thermal, RGB and multispectral images, chlorophyll content, volumetric soil moisture, air temperature and relative humidity measurements were taken for each sample every two days. The obtained results clearly indicate the dependence between CWSI and plant condition parameters in the first phase of desiccation. At the same time, as a result of the observations taken, thresholds have been set, indicating different desiccation phases.

The purpose of this paper is to describe a new way of producing renewable energy based on fjords as a water heater. We will call this system the Water-thermal Energy Production System (WEPS), because the basic idea is to extract heating and cooling energy from water. Although a prototype of WEPS has existed in Norway for more than ten years, a WEPS currently in operation has not been financially analyzed in the literature. Coastal parts of Norway have a potential of 5 TWh of profitable WEPS-facilities [9], due to convenient access to fjords containing water with stable all-season temperatures of about 4–12C when the depth of the water is about 50 meters. This stability of the water temperature makes it possible to extract energy from the fjord in a very efficient way. The potential for economically-profitable WEPS in other parts of the world has not been estimated. In order to answer such a question, more research is required. We have conducted a case study of a WEPS located in the Norwegian municipality of Eid. This is the first full-scale Norwegian WEPS, and it has been operating since 2006. The nascent years have passed, and the technology has been in operation for some years. In this paper, we have made an estimate of the business profitability and the external effects based on past empirical evidence and some assumptions about future development in some key figures. The results suggests that WEPS-Eid has been a profitable investment carrying a positive internal rate of revenue, even if the present underutilization in production capacity will continue in the future. Stability in energy prices for heating purposes has also gained customers compared to the more volatile prices of alternative renewable energy, like hydropower or wind turbines. The negative, external effects in the operating phase from WEPS-Eid are insignificant. Despite the significant profitability of the WEPS facility in Eid, there are two main obstacles for new entrants. There is a lack of relevant operational information for potential investors due to few facilities. This leads to uncertainty, and investments in WEPS appear as a risky business. Secondly, construction of a WEPS requires both big financial investments in digging and facilitating long trenches for a pipeline system and time and effort spent on acquiring the licenses needed for doing this work. A coordinating unit is probably required in order to get the necessary public and private licenses and to reduce fixed costs by coordinating other tasks in the same trenches, like pipes for water and sewer, fiber cables and tele-cables. In Eid, the local municipal administration was the coordinating unit.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

The physicalchemistry properties and crystal structure of were nano-ZrO₂+3mol.%Y₂O₃ determined. The kinetics of the formation of H₂ as a result of the decomposition of H₂O on the surface of nano-ZrO₂+3mol.%Y₂O₃ was studied. Effects of adsorption and desorption process on ZrO₂+3 mol.%Y₂O₃ nanoparticles were studied at different (T=400÷1000⁰C) temperature. The study of H₂ in thermal processes at nano-ZrO₂+3 mol.%Y₂O₃ system increased. Such an increase in H₂ generation in comparison with a pure H₂O as thermal processes had formedactive centers for H₂O decomposition on the surface of the catalyst at the expense of δ-electrons emitted on the surface of nano-ZrO₂+3 mol.%Y₂O₃. This showed that the dimensions of the studied nanoscale particles systems are comparable to the free running distance of energy carriers generated by of nano-ZrO₂+3 mol.%Y₂O₃ as a result of thermal processes. These results are promising for hydrogen generation by waer spliting in near future.

Compact solar-powered plasma water generator: enhanced on-site aged seed germination with the corona dielectric barrier discharger

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Ultralong carbon nanotubes (UCNTs) are highly demanded for nanocomposites applications because of their magnificent physical and chemical properties. UCNTs are synthesized by catalytic chemical vapor deposition (CCVD) method and, before using as fillers in nanocomposites, should be purified from residual catalyst and non-CNT particles without significant destruction or scissoring of UCNTs. The role of water vapor for purification of UCNTs is investigated, the importance of water assistance in this process is confirmed. It was shown that wet air treatment of products of UCNTs CCVD synthesis under mild conditions can be used to decrease sufficiently residual catalyst content without significant carbon losses in comparison with the results obtained with dry air, while the residual iron content was shown to influence heavily on the subsequent oxidation of different forms of carbons, including UCNTs. The increasing of D/G ratio of Raman spectra after wet air treatment of products of UCNTs CCVD synthesis makes it possible to conclude that iron catalyst particles transform into iron oxides and hydroxides that caused inner structural strains and destruction of carbon shells improving removal of the catalyst particles by subsequent acid treatment. UCNTs purification with water assistance can be used to develop economically and ecologically friendly methods for obtaining fillers for nanocomposites of different applications.

In this study, we successfully synthesized a novel branched polyamide 6 with ε-caprolactam(CPL) and α-Amino-ε-caprolactam(ACL) through hydrolytic ring-open co-polymerization. The NMR characterization and rheological test result proved the existence of branched chain structure additionally. The branched chain structure caused a remarkable enhancement in the rheological properties. The met index(MFR),zero shear rate viscosity and storage modulus at low frequency region had a remarkable increase.The shear thinning phenomenon became more obvious. The thermal properties test determined by differential scanning calorimetry(DSC) showed that the melting point and crystallinity of co-polymers decreased with the increase of ACL addition.However, the crystal structure of the samples remained unchanged. The appropriate addition amount of ACL can improve the tensile mechanical properties of the co-polymers. When the amount of ACL was 1%, the tensile strength and fracture elongation rate of the co-polymers had the most significant increase.

This research is a preliminary phase of a general effort to develop a generic-data transferring capability via human haptic thermal sensation (generic-data refers to a coded language like Morse or Braille). For the capability to be effective, it must include a large variety of short recognizable cues. Hence, we propose the concept of cues based on sequences of thermal pulses, i.e., combinations of warm and cool pulses with several levels of intensity. The objective of this study was to determine the feasibility of basing a generic-data-transfer capability on thermal cues composed of sequences of short pulses. The research included defining the basic characteristics of the stimuli parameters and developing practical methods for generating and measuring them. Several sequences were designed in light of the relevant data known to date, and tests were conducted. The thermal cues presented to the participants were sensed and recognized by touch. The results indicate high feasibility for a capability that is applicable in various scenarios. In addition, the low impact on human skin temperature due to short stimuli duration represents an inherent advantage for later implementation. This report presents promising findings and offers insights for further investigation.

The development of photocurable compositions is in high demand for the manufacture of func-tional materials for electronics, optics, medicine, energy, etc. The properties of the final pho-to-cured material are primarily determined by the initial mixture, which needs to be tuned for each application. In this study we propose to use simple systems based on di(meth)acrylate, polyimide and photoinitiator for the preparation of new photo-curable compositions. It was es-tablished that a fluorinated cardo copolymide (FCPI) based on 2,2-bis-(3,4-dicarboxydiphenyl)hexafluoropropane dianhydride, 9,9-bis-(4-aminophenyl)fluorene and 2,2-bis-(4-aminophenyl)hexafluoropropane (1.00:0.75:0.25 mol) has excellent solubility in di(met)acrylates. This made it possible to prepare solutions of FCPI in such monomers, to study the effect of FCPI on the kinetics of their photopolymerization in situ and the properties of the resulting polymers. According to the obtained data, the solutions of FCPI (23 wt.%) in 1,4-butanediol diacrylate (BDDA) and FCPI (15 wt.%) in tetraethylene glycol diacrylate were tested for the formation of the primary protective coatings of the silica optical fibers. It was found that the new coating of poly(BDDA–FCPI23%) can withstand prolonged annealing at 200°C (72 h), which is comparable or superior to the known most thermally stable photo-curable coatings. The proposed approach can be applied to obtain other functional materials.

This paper offers a theoretical and experimental examination of the concurrent production of electricity and heat using photovoltaic thermal (PV/T) technology. The efficiency performance of the PV/T system is meticulously analyzed using MATLAB/Simulink software environments. Notably, the proposed PV/T system shows reliable performance, and its validity is confirmed through experimental validation on a test stand with a single PV/T panel positioned at a 45-degree angle to the horizontal and a 0-degree azimuth angle.

The effect of Localized Surface Plasmon (LSP) of 5 nm mean size Au particles deposited on TiO2 P25 was investigated during the photo-thermal water gas shift reaction (WGSR). The effects of CO concentration, excitation light flux and energy, and molecular oxygen addition during the reaction were investigated. The photocatalytic WGSR rate under light excitation with wavelengths extending from 320 to 1100 nm was found to be higher than the thermal reaction alone at the same temperature (85 oC). A ratio H2/CO2 of near unity was found at high concentrations of CO. Addition of molecular oxygen during the reaction resulted in a slight decrease of molecular hydrogen production while the rates of CO2 formation and that of CO consumption changed by one order of magnitude. More important, it was found that the WGSR rates were still high under only visible light excitation (600 - 700 nm). The results prove that Au LSP alone triggers this chemical reaction without the need to excite the semiconductor on which they are deposited.

We introduce a series of twisted donor-acceptor (D-A) carbazole-benzophenone based electroactive bipolar derivatives that were synthesized through the reaction of 4-fluorobenzophenone with various partially alkylated 3,3’-bicarbazoles. The comprehensive structural characterization of these compounds is provided. These amorphous materials exhibit suitable glass transition temperatures ranging from 57 to 102 °C and demonstrate high thermal stability, with decomposition temperatures reaching 400 °C. Moreover, the developed materials exhibit elevated photoluminescence quantum yields (PLQY) of up to 75.5% and favorable HOMO-LUMO levels, along with suitable triplet-singlet state energy values. Due to their good solubility and suitable film-forming properties, all the compounds were evaluated as blue emitters dispersed in 4,4’-bis(N-carbazolyl)-1,10-biphenyl (CBP) host for the fabrication of organic light-emitting diodes (OLEDs) in concentration dependent experiments. Among these experiments, the device containing 15 wt% of the guest 4-(9’-{2-ethylhexyl}-[3,3’]-bicarbazol-9-yl)benzophenone demonstrated the best characteristics, achieving maximum brightness of 3581 cd/m2, current efficiency of 5.7 cd/A, power efficiency of 4.1 lm/W and external quantum efficiency of 2.7%.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

A compact Mach-zehnder interferometer with a novel design of directional couplers and a phase shifter has been presented as a thermo-optical sensor. With the aim of reducing device size to micro and nano dimension silicon-on-insulator technology was employed. That allowed miniaturization of device size through the reduction of its cross sectional area to 0.066 µm² and the radius of curvature of both the arms of the directional coupler and S-bends of the phase shifter to 5 µm and C-bends to 3 µm. These nano size device dimensions made it possible to reduce the coupling gap to 0.2 µm, which resulted in a significant reduction in the coupling length. The device geometry and its performance characteristics were analyzed and optimized using coupled mode analysis and finite difference time domain simulation tools, respectively. The wavelength dependent transmission loss of the device was measured at different temperature to verify and validate its performance characteristics. Tested devices showed a remarkable temperature dependent transmission characteristic offering significant changes in transmission loss band – with as low as 0.45 ⁰C change in substrate temperature. The extinction ratio and the free spectral range of the device were 26 dB and 0.26 nm respectively in the wavelength range of 1549.5 nm – 1550.5 nm. These results imply that the devices presented here can be used as compact and highly sensitive thermal sensors and optical switches.

This paper introduces a new adaptation of the enthalpic lattice Boltzmann method (LBM) tailored to simulate the intricate dynamics of conjugate heat transfer in non-homogeneous media, showcasing considerable potential for enhancing heat exchanger designs. This approach expands upon the conventional enthalpic LBM framework by seamlessly incorporating tailored source terms, enabling precise representation of local and transient variations in the medium’s thermophysical properties. The resulting LBM model comprehensively captures the energy conservation equation, with exceptions made only for flow compressibility and viscous dissipation, thereby significantly augmenting its versatility in analyzing heat exchanger configurations. Verification tests, comprising assessments of both transient and steady-state solutions, unequivocally validate the accuracy of the proposed model, further bolstering its reliability for analyzing heat exchange processes within intricate heat exchanger geometries. To demonstrate its efficacy, simulations of conjugate heat transfer processes involving fluid natural convection within structured cavities were performed, imposing both Dirichlet and Neumann boundary conditions to emulate scenarios encountered in practical heat exchanger operations. The findings yield compelling insights, particularly in the transient regime, revealing the beneficial impact of structured cavities on enhancing heat transfer processes. These insights inform potential design optimizations for heat exchangers. The results emphasize the potential of the modified enthalpic LBM approach to elucidate complex heat transfer phenomena in non-homogeneous media and structured geometries, offering valuable implications for heat exchanger engineering and optimization.

The thermoelectric generator (TEG) has much potential as a renewable energy technology that could be used in ocean thermal energy conversion (OTEC). This technique employs TEGs and heat exchangers as substitutes for the intricate elements found in conventional OTEC systems, including pressure valves, evaporators, condensers, and turbine generators. By harnessing the temperature difference between warm surface seawater and cold deep seawater, it facilitates the conversion of this thermal gradient into electrical energy. This study used computer simulations to look at and compare three different types of heat exchangers: a cavity-type heat exchanger, a heat exchanger with flat fins, and a heat exchanger with longitudinal vortex generators (LVGs). The objective was to evaluate the influence of these designs on the thermoelectric conversion performance when implemented in OTEC systems. The study's findings indicate that using heat exchanger configurations featuring flat fins, or LVGs, enhances the efficiency of thermal energy transfer from warm seawater to TEGs, resulting in a notable enhancement in the output power of TEGs. Furthermore, the efficiency of TEG thermoelectric conversion is influenced by varying seawater flow rates in relation to the performance of flat fins and LVGs. In contrast to the cavity-type heat exchanger, the utilization of a heat exchanger equipped with flat fins has been found to yield a notable enhancement in the output power of TEGs by approximately 22.92%. Furthermore, this configuration demonstrates a substantial improvement in thermoelectric conversion efficiency, exhibiting an increase of around 40.01%. These improvements are observed under certain conditions pertaining to flow rates and fin heights. Utilizing heat exchangers equipped with LVGs has been found to enhance the output power of TEGs by 13.02% and improve the overall thermoelectric conversion efficiency by 17.72%. These improvements are observed under certain conditions, including specific flow rates, LVG tilt angles, and locations.

The well-being and sociability of individuals have always been part of modernity. The development of new technologies that meet these aspirations is receiving increasing attention. Thus, strengthening the desired objectives of these tools and minimizing their undesirable side effects is the subject of a growing commitment. The present contribution aims, in this context, to evaluate and analyze the desired and undesirable effects of the interaction of electromagnetic fields with living tissues in general. This involves routines reinforcing expected functions as well as those controlling and protecting against undesirable effects. First, the interactions of electromagnetic fields with tissues are analyzed, involving their thermal biological effects of desired and undesired exposures. The roles of blood and sap fluids in bio-affected tissues are then analyzed. Secondly, the governing electromagnetic, bio-heat equations, and their coupled solution are studied. Third, the thermal behavior of tissues and the exposure adverse effects are examined. Next, monitoring and defending of the effects of exposures are discussed. This contribution illustrates and discusses mathematical modeling routines based on a generalized interaction of electromagnetic fields with living tissues.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

Ultra-large cold-water pipes (CWP) may present structural instability phenomenon under complex and variable operating conditions, and the current theoretical analysis rarely takes into account the influence of multiple key parameters at the same time, resulting in some errors between the prediction results and the actual deformation behavior of the pipe. Considering this issue, this paper establishes a computational analysis model of the mechanical performance of the CWP based on the Euler-Bernoulli beam theory, considering the effect of waves, the clump weight at the bottom, internal flow and sea current, and gives a time-dependent solution of the mechanical response of the pipe with the action of multiple key parameters using the differential quadrature method (DQM). Additionally, the correctness and validity of the theoretical model are well verified by comparing the numerical solution with the theoretical results. Finally, to study the effects of operating conditions on the mechanical response of the pipe, the effects of waves, the clump weight, internal flow and sea current on the lateral deflection and maximum bending moment of the pipeline are discussed based on numerical simulation and orthogonal experimental method. The results show that changing the wave strength and internal flow velocity has little effect on the lateral deflection of the CWP, and the clump weight at the bottom can effectively suppress the lateral deflection of the pipeline, but increasing the current velocity can significantly increase the lateral deflection of the pipeline, which can lead to the instability of the pipe. Nevertheless, the effects of waves, the clump weight, internal flow and sea current on the maximum bending moment of the pipeline are basically the same, all of them increase sharply at first, and then decrease gradually until they level off, and the differences in the effects are mainly reflected in the different locations of the pipe sections. This paper suggests the design guidance of CWP in aspect of dynamic response depending on the operating condition.

The subject of the conducted study was focused on the development of new type of technical blends reinforced with natural fillers. The study was divided into two parts, where in the firsts stage of the research unmodified POM was reinforced with different types of natural fillers: cellulose, wood flour and husk particles. In order to select the type of filler intended for further modification, the mechanical characteristics was assessed. The 20% wood flour (WF) filler system was selected as the reinforcement. The second stage of research involved the use of combination of polyoxymethylene POM and poly(lactic acid) PLA. POM/PLA blend (ratio 50/50 %) were modified with elastomeric compound (EBA) and chain extender as reactive compatibilized (CE). The microscopic analysis revealed that for POM/PLA system the filler-matrix interface is characterized by better wettability, which might suggest higher adhesion. The mechanical performance revealed that for POM/PLA-based composites the properties were very close to the results for POM-WF composites; however, there is still large difference in thermal resistance in favor of POM-based materials. The increase in thermomechanical properties for POM/PLA composites occurs after heat treatment. The increasing crystallinity of the PLA phase allows for an significant increase of the head deflection temperature (HDT), even above 125 °C.

Laboratory experiments and investigations into natural phenomena in this research series have unveiled the presence of a gravitational repulsion force that permeates our environment on both microscopic and macroscopic scales, contingent upon the thermal energy present. This paper presents a study exploring novel properties of gravitational forces among gas molecules, employing principles of thermodynamics. A model has been devised based on the interactions between pairs of gas molecules. While traditional models treat gravitational interaction as a singular force, our experimental approach validates it as the composite of two distinct forces: gravitational repulsion and attraction. By utilizing established experimental data on gas thermodynamics, our model demonstrates robust performance both analytically and experimentally. It verifies the coexistence of gravitational repulsion and attraction forces among gas molecules, showcases their Inverse-Cube relationship with distance, and elucidates the direct proportionality of the repulsion force to absolute temperature. This bridges a crucial gap between energy and fundamental forces. The order of magnitudes of gravitational repulsion and attraction forces are found to be considerably large, contrasting with the low values predicted by classical theory, which results from their amalgamation. Recognizing these forces as substantial in magnitude promises unprecedented outcomes and advancements.

In Mexico viticulture represents the second source of employment in the agricultural area after the fruit and vegetable sector. In developed countries, remote sensing is widely used for vineyard monitoring, however, this tool is barely used in developing countries of Iberoamerica. In this re-search, our overall objective is to characterize two vineyards in the state of Queretaro (Mexico) using Sentinel-2 and meteorological data, specifically spectral and thermal indices. Results showed that spectral indices obtained from Sentinel-2 bands have characterized adequately the phenolog-ical evolution of the different varieties of the vineyards. The Modified Soil-Adjusted Vegetation Index (MSAVI) was adequately used to discriminate the first stages of vineyards, while the Nor-malized Difference Vegetation Index (NDVI) was useful to monitor vineyards during the rest stages of vineyards. Thermal indices have shown that the best grape varieties were those that can adapt to both cooler and warmer temperatures, have a reasonable ripening period, and can produce wines with balanced acidity and flavors. In conclusion, the combination of meteorological (including thermal indices) and remote sensing data (NDVI and MSAVI) provide information for choosing the suitable grape variety for this region.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

The growing interest in heat-conducting nanofluids requires highly sensitive methods for analyzing thermal properties. Thermal-lens spectrometry, despite its advantages over classical methods, does not have a general approach to measuring and interpreting results for dispersed systems. In this paper, by the example of nanofluids of silicon oxide in water in a wide range of concentrations and sizes, the selection of measurement parameters for transient and steady-state thermal lensing is justified, and the interpretation of the results of thermal diffusivity measurements is substantiated. The features of measurements of thermal diffusivity by thermal lens spectrometry under stationary state for dispersed systems are considered. Using this approach, it is possible to detect and distinguish thermal effects with high accuracy. For dispersions of silicon oxide, with increasing concentration, the thermal diffusivity passes through a minimum. Silicon oxide dispersions can be used both as a coolant or as a heat-removing liquid by selecting the particle size and concentration.

Climate warming is expected to have pronounced effects on Arctic and Subarctic ecosystems, especially regions underlain by discontinuous and relatively warm permafrost. The main goal of this research is to evaluate the vulnerability and dynamics of permafrost under climate warming across the various ecotypes in respect of ecosystem stability, socioeconomic impact, and for better understanding possible future environmental changes. We suggested the new version of the spatially distributed permafrost dynamics model (GIPL2-MPI), which is developed in the Geophysical Institute, University of Alaska Fairbanks. This model is based on the ecosystem approach to simulate the permafrost dynamics, which we are discussing in this paper. We combined ground-based observations and numerical freeze/thaw modeling using climate-ecosystem-permafrost interactions to understand the physical processes and mechanisms controlling permafrost physical state. We predict the changes in permafrost conditions using output from two GCMs (NCAR-CCSM4 and GFDL-CM3) and Five-Model Average Ensemble for the RCP-4.5 and RCP-8.5 scaled down to 1 by 1 km spatial resolution (https://uaf-snap.org/) across entire Alaska. Our result shows that by the end of the current century widespread near-surface permafrost degradation could begin everywhere in Alaska southward of the Brooks Range as well as across some spots at the North Slope Alaska.

Steam boiler has a significant role in the industrial sector. The failure in boiler tubes significantly reduces the availability of the plant. Furthermore, deposits on the inner tube wall contribute to such failure by changing the thermal resistance of the wall, which causes a significant increase in the tube wall's temperature and, consequently, lower allowable stress. The presented thermal-fluid model is developed for the water tube. The model is implemented using ANSYS FLUENT to estimate the wall maximum water tube wall temperature considering the deposits layer and then determine the minimum thickness of the tube wall via ASME standards to assure safe operation. The model is verified via a mesh independence test. The minimum tube thickness is recommended and justified given the thermo-mechanical performance of the water tubes at several operating loads of 50, 75, and 100 %. These loads are implemented by different convective heat transfer coefficients of flue gases under different deposit thicknesses, thermal conductivity, and flue gas temperature. The present work contributes to the literature by recommending the minimum thickness of the water wall tubes and highlighting the thermo-mechanical effect of the deposits on water tube resilience under different operating conditions.

The Planetary Roller Screw Mechanisms (PRSMs), alongside Ball Screw Mechanisms (BSMs) and Electromechanical Actuators (EMAs), occupies a pivotal role in advancing the precision and efficiency of various industrial applications, including aerospace, automotive, and high-precision machining tools. Despite their critical advantages such as high load capacity, superior precision, and extended lifespan, the deployment of PRSMs in complex operational conditions reveals a landscape rife with challenges and opportunities for further research. This comprehensive review endeavors to dissect the multifaceted aspects of PRSMs, focusing on their mechanics and dynamics, tribology and thermal behavior, and the paramount importance of reliability and condition monitoring. By synthesizing current research findings, this paper highlights the significant advancements in understanding the static and dynamic characteristics of PRSMs, the intricate interplay between lubrication conditions and wear mechanisms, and the critical role of thermal effects on operational performance. Moreover, it delves into the dynamic models that address the impact of manufacturing imperfections, such as waviness and defects, on the reliability of these mechanisms. Despite the strides made, the review identifies critical gaps in the existing literature, particularly under conditions of extreme temperatures, large deformations, and multifaceted loads, advocating for a holistic approach to research. By proposing integrated thermo-mechanical models and emphasizing the need for empirical validations, this paper outlines a roadmap for future studies aimed at facilitating the development of more robust and reliable PRSMs, capable of meeting the demands of complex operational scenarios and advancing the field of high-precision applications in aerospace, robotics, and beyond.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

This paper reports the overall thermal performance of a cylindrical parabolic concentrating solar water heater (CPCSWH) with inserting nail type twisted tape (NTT) in the copper absorber tube for the nail twist pitch ratios 4.787, 6.914 and 9.042 respectively. The experiments are conducted for a constant volumetric water flow rate and during the time period 9:00 h to 15:00 h. The useful heat gain, hourly solar energy collected and hourly solar energy stored of this solar water heater are found higher for nail twist pitch ratio 4.787. The above said parameters are found to be a peak at noon and observed to follow the path of variation of solar intensity. At the starting of the experiment, the value of charging efficiency is observed to be maximum. Whereas the maximum value of instantaneous efficiency and overall thermal efficiency are observed at noon. The key finding is that the nail twist pitch ratio enhances the overall thermal performance of the CPCSWH.

In urban area, one of the great problem is the rise of temperature, which leads to form the urban heat island effect. This paper refers to the trend of the urban surface temperature extracted from the Landsat images from which to consider changes in the formation of surface urban heat island for the north of Ho Chi Minh city in period 1995-2015. Research has identified land surface temperature from thermal infrared band, according to the ability of the surface emission based on characteristics of normalized difference vegetation index NDVI. The results showed that temperature fluctuated over the city with a growing trend and the gradual expansion of the area of the high-temperature zone towards the suburbs. Within 20 years, the trend of the formation of surface urban heat island with two typical locations showed a clear difference between the surface temperature of urban areas and rural areas with space expansion of heat island in 4 times in 2015 compared to 1995. An extreme heat island located in the inner city has an area of approximately 18% compared to the total area of the region. Since then, the solution to reduce the impact of urban heat island has been proposed, in order to protect the urban environment and the lives of residents in Ho Chi Minh City becoming better

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

There are several challenges on how to attain energy efficiency while maintaining balance among factors affecting energy consumption such as power rating and temperature setpoints of cooling units, room temperature and humidity, and indoor air quality (IAQ). A real-time energy and IAQ monitoring system were installed in an educational building to profile the operational power consumption of inverter-based air condition unit (ACU) installed in each room. Polynomial curve and neural fitting regression analysis were applied to the real-time power consumption, indoor temperature and humidity, and carbon dioxide (CO2) level data. The derived models were able to provide the stabilizing indoor thermal and air conditions of the room to reach steady state ACU power consumption. These collected data and calculated parameters can be used to define rules in automating control of cooling appliances for an efficient energy utilization. The regression approaches, using real-time data, have determined the influence of indoor heat conditions and carbon dioxide levels on ACU power consumption. These parameters were utilized to establish consistent values for temperature, humidity, and carbon dioxide levels under stable settings of inverter-based air conditioning units.

Abstract: : 2,3-dihydro-5,6,7,8-tetranitro-1,4-benzodioxine (TNBD), molecular formula =C8H4N4O10 is a completely nitrated in aromatic ring 1,4-benzodioxane derivative. The con-venient method of TNBD synthesis was developed (yield=81 %). The detailed structure of this compound has been investigated by X-ray crystallography. The results of differential thermal analysis (DTA) obtained with twice re-crystallized material showed onset at 247 and isoterm at 288 0C, with further total degradation at 300 0C. The experimental density 1,85 g/cm3 of TNBD was determined by X-ray crystallography. The spectral properties of TNBD (NMR, FT-IR, Ra-man) were explored. The detonation properties of TNBD calculated by EXPLO 5 code was slightly superior in comparison to standard high energy material - tetryl (detonation velocity of TNBD - 7727 m/s; detonation pressure - 278 kbar; tetryl – 7570 m/s and 226.4 kbar at 1.614 g/cm3, or 260 kbar at higher density - 1.71 g/cm3. The obtained preliminary results might suggest TNBD can be a potential thermostable high energy and density material (HEDM).

Land Surface Temperature (LST) is routinely retrieved from remote sensing instruments using semi-empirical relationships between top of atmosphere (TOA) radiances and LST, using ancillary data such as total column water vapor or emissivity. These algorithms are calibrated using a set of forward radiative transfer simulations that return the TOA radiances given the LST and the thermodynamic profiles. The simulations are done in order to cover a wide range of surface and atmospheric conditions and viewing geometries. This work analyses calibration strategies, considering some of the most critical factors that need to be taken into account when building a calibration dataset, covering the full dynamic range of relevant variables. A sensitivity analysis of split-windows and single channel algorithms revealed that selecting a set of atmospheric profiles that spans the full range of surface temperatures and total column water vapor combinations that are physically possible seems beneficial for the quality of the regression model. However, the calibration is extremely sensitive to the low-level structure of the atmosphere indicating that the presence of atmospheric boundary layer features such as temperature inversions or strong vertical gradients of thermodynamic properties may affect LST retrievals in a non-trivial way. This article describes the criteria established in the EUMETSAT Land Surface Analysis – Satellite Application Facility to calibrate its LST algorithms applied both for current and forthcoming sensors.

In recent years, several alternatives for improving the thermal comfort conditions inside buildings have been proposed. Among these alternatives, Thermally Activated Building Systems (TABS) have become of interest due to the benefits this technology brings to the building sector. The TABS are embedded in different building components and exchange heat with building envelope to improve the indoor air temperature. This review presents relevant results presented in the literature on the thermal behavior of TABS, the different types of TABS configurations, and the main parameters of TABS studied such as pipe separation, fluid inlet temperature, fluid velocity, and volumetric flow rate. The potential of TABS to improve thermal comfort conditions and provide energy savings is also discussed. Further, this study presents the different modes of application.

QSO B0218+357 is a blazar located at a cosmological redshift of 0.944. The source is gravitationally lensed by a spiral galaxy located at the redshift of 0.68. Strong gravitational lensing splits the signals emitted by the source into two components separated by 10-12 days, as observed in radio and gamma-ray bands. In July 2014 a GeV flare was observed by Fermi-LAT, triggering follow-up observations with the MAGIC telescopes at energies above 100 GeV. The expected time delay between the components allowed us to plan broad band MWL observations before, during and after the trailing component of the emission. The MAGIC observations at the expected time of arrival of the trailing component resulted in the first detection of QSO B0218+357 in Very-High-Energy (VHE, >100 GeV) gamma rays. It is both the farthest known VHE object and one of only a few Flat Spectrum Radio Quasars detected in this energy range. We report here the observed multiwavelength spectral and temporal properties of the emission during the 2014 flare.

The aim of this study is to analyse problems related to thermal mapping obtained from thermal data acquired from Unmanned Aerial Systems (UAS) equipped with thermal cameras. We focused on an accurate analysis of uncertainties introduced by the PIX4D Mapper software used to obtain the surface temperature maps of thermal images acquired by the UAS. To achieve this aim, we used artificial thermal reference during the surveys, as well as natural hot targets, i.e. thermal anomalies in the Pisciarelli hydrothermal system in Campi Flegrei caldera (CFc). Artificial thermal targets, expressly created and designed for this goal, are a prototype here called “developed thermal target” (DTT) made by the drone Laboratory at Istituto Nazionale di Geofisica e Vulcanologia - Osservatorio Vesuviano (INGV-OV). We show the results obtained by three surveys during which thermal targets were positioned on land at different flight heights of the UAS. Different heights were also necessary to test spatial resolution of the DTT with the used thermal camera as well as possible temperature differences between the raw images acquired by UAS with the thermal mapping obtained from the PIX4D Mapper software. In this work we have estimated the uncertainty that may be introduced by the mosaic procedure and furthermore we find an attenuation of the measured temperatures introduced by the different distances between the thermal anomaly and sensor. These results appear to be of great importance for the subsequent calibration phase of the thermal maps especially in cases where these methodologies are applied for monitoring purposes of volcanic/geothermal areas.

Low-cost miniature hyperspectral and thermal cameras onboard lightweight unmanned aerial vehicles (UAV) bring new opportunities for monitoring land surface variables at unprecedented fine spatial resolution with acceptable accuracy. This research applies hyperspectral and thermal imagery from a drone to quantify upland rice growth and water use efficiency (WUE) after biochar application in a Costa Rican dry region. The field flights were conducted over two experimental groups with bamboo biochar and sugarcane biochar amendments and one control group without biochar application. Rice canopy biophysical variables were estimated by inversion of a canopy radiative transfer model on hyperspectral reflectance. Variations in gross primary production (GPP) and WUE across treatments were estimated from the normalized difference vegetation index (NDVI), canopy chlorophyll content (CCC), and evapotranspiration. We found that GPP was increased by 41.9±3.4 % when using bamboo biochar and 17.5±3.4 % when using sugarcane biochar, which was probably due to higher soil moisture in the biochar-amended plots and led to significantly higher WUE by 40.8±3.5 % in bamboo biochar and 13.4±3.5 % in sugarcane biochar. This study demonstrated the use of hyperspectral and thermal imagery from drone to provide indicators for quantifying biochar effects on tropical dry cropland by integrating with ground point samples and physical models.

A thermal-oxidative aging test at 120°C was condutcted on Ethylene Propylene Diene Monomer (EPDM) vulcanizates of the semi-efficient vulcanization system. The effect of thermal-oxidative aging on EPDM vulcanizates was systematically studied by curing kinetics, aging coefficient, cross-linking density, macroscopic physical properties, contact angle, Fourier Transform Infrared Spectrometer (FTIR), Thermogravimetric analysis (TGA) and thermal decomposition kinetics. The results show that the content of hydroxyl and carbonyl groups as well as the carbonyl index increased with increasing aging time, indicating that EPDM vulcanizates are gradually oxidized and degraded. As a result, the EPDM vulcanized rubber chains were cross-linked, and its conformational transformation was limited and its flexibility was weakened. The thermogravimetric analysis demonstrates the thermal degradation of EPDM vulcanizates had competitive reactions of cross-linking and degradation, and the thermal decomposition curve can be divided into three stages, meanwhile the thermal stability of EPDM vulcanizates gradually decreases with the increase of aging time. The introduction of antioxidant in the system can promote the cross-linking speed and reduce the cross-linking density of EPDM vulcanizates, while inhibiting the surface thermal and oxygen aging reaction. This is attributed to the fact that the antioxidant can reduce the thermal degradation reaction level, but it is not conducive to the formation of a perfect crosslinking network structure and reduce the activation energy of thermal degradation of the main chain.

A variety of factors ranging from ethnicity and occupants’ lifestyles to local climatic characteristics of any studied location and people’s age factors can affect thermal comfort assessment globally. Due to the detrimental impact of climate change, the building industry has started to implement energy efficiency schemes while considering the thermal comfort of vulnerable population both for the society and any sphere of economy. Although, considering human-based approaches have been neglected by other scholars in thermal comfort studies. This paper reviews energy effectiveness of state-of-the-art passive systems in providing neutral adaptive thermal comfort for elderly people, through exploring passive design strategies in four distinct climates namely, Canada, India, Abu Dhabi and the South-eastern Mediterranean basin. The aim of the study is to analyze the available data provided by the ASHRAE Global Thermal Comfort Database II version record 2.1. The main objective of the study is to develop an effective methodological framework for the on-going development of adaptive thermal comfort theory. To this extend, this study presents a comprehensive review on the assessment of energy effectiveness of passive design systems. To accomplish this, the impact of climate change factor in passive design systems was investigated. The meta-analysis method was adopted to determine the input variables for the statistical analysis. Cramer’s V and Fisher’s Exact tests were used to assess occupants’ thermal sensation votes (TSVs). The findings revealed that there are discrepancies detected between the in-situ field experiments and the data recorded in the ASHRAE Global Thermal Comfort Database II. According to the Köppen-Geiger climate classification, it was found from the study that the slightly high temperature fluctuations were identified in India where the weather is dry and savanna climate. The study findings contribute to the development of adaptive thermal comfort theory by reviewing the existing methodologies globally. Furthermore, a critical review on the significance of occupants’ age differences should be conducted in the identification of neutral adaptive thermal comfort.

The study sought to determine solar irradiation in Homa Bay County which can be tapped and utilized in improving lives of residents of the region by converting the solar thermal energy in Home Bay to other forms of energy such as electric form, mechanical form and light. The study was done by assessing the local atmospheric conditions which included sunshine duration data and air temperature records for the period of two years and the data obtained subjected to statistical analysis to determine the localized characteristics of the resource. The characteristics that were examined include; seasonal and annual power expectations as well as resource reliability. The solar irradiance of Home County was found to be 768.0 W/m².

What proportions should a thermally massive building have? How should the thermal mass be distributed? Should the "massing" change with the choice of material? This paper shows how to optimize the physical proportions of a building so that it synchronizes ambient heat exchanges in a natural feedback cycle. The internal mass is thermally coupled with buoyancy ventilation; the cycle is driven by the daily swing of outdoor temperature. Tripling up functions in this way—so that structural materials can reliably cool and power the ventilation for buildings—could help decarbonize the construction industry and provide an effective strategy for adapting to life-threatening heatwaves. Based on harmonic analysis, the method allows designers to thermally tune the form and mass of a building to meet chosen targets for temperature and ventilation in free-running mode. Once the optimal balance of exchange rates is known, design teams can proportionally vary the building height and ventilation openings against the surface area and thickness of an internal thermal mass. The possible permutations are infinite but parametrically constrained, allowing teams to fairly compare the functional and environmental credentials of different construction materials while they produce and evaluate preliminary options for organizing the exterior form and interior spaces of a building. An example study suggests that thin-shell structures of minimum weight, and even timber buildings, may be optimally tuned to produce ample ventilation and temperature attenuation.