Solar energy is derived from photons of light coming from the sun in a form called radiation. Solar energy finds extensive application in air and water heating, solar cooking, as well as electrical power generation, depending on the way of capturing, converting and distribution. To enable such application, it is necessary to analyze the horizontal tilt angle of horizontal surfaces – in order that when the solar energy reaches the earth surface to be completely absorbed. This paper tends to describe the availability of solar radiation for south-facing flat surfaces. The optimal monthly, seasonal, and annual tilt angles have been estimated for Pristina. The solar radiation received by the incident plane is estimated based on isotropic sky analysis models, namely Liu and Jordan model. The annual optimum tilt angle for Pristina was found to be 34.7°. The determination of annual solar energy gains is done by applying the optimal monthly, seasonal and annual tilt angles for an inclined surface compared to a horizontal surface. Monthly, seasonal and annual percentages of solar energy gains have been estimated to be 21.35%, 19.98%, and 14.43%. Losses of solar energy were estimated by 1.13 % when a surface was fixed at a seasonal optimum tilt angle, and when it was fixed at an annual optimum tilt angle, those losses were 5.7%.

Solar pavement technology has numerous benefits for advanced life and environmental protection, including reduced fossil fuel usage, reduction harmful emissions from conventional electricity generation and handy reliable electricity via solar energy. This paper aims to find an alternative for cost effective renewable energy sources is in conjunction with the principles of sustainability. This research studies whether the application of thermal energy harvesting road pavement using sustainable conductive piping such as stainless steel, copper, and aluminium are feasible in Malaysia. The scope of the paper is to optimize the suitable parameters for different materials of thermal energy harvester such as pipe material, pipe depth inserted into pavement, types of pipe arrangement, pipe spacing, and flow rate for maximum thermal energy extraction using numerical simulation. The simulation is testing under engineering software ANSYS Workbench 19.2 (Fluent) and Solidworks 2020 to develop project prototype from optimize thermal energy harvester. Thus, serpentine copper pipe shows the highest heat efficiency which is 32.22% with the temperature outlet of 327.35K (54.21°C) at the pipe located at 50 mm from the surface pavement with the pipe spacing of 80 mm centre-to-centre.

In the context of the French tertiary decree, it is crucial to reduce the energy consumption of buildings by first addressing the design of the electrical architecture. Implementing Direct Current (DC) nanogrids in buildings could offers a promising advantage for energy efficiency, significantly impacting overall energy consumption and sustainability goals. For an insulated area with a subtropical climate, such as La Réunion island, DC nanogrids could also facilitate the insertion of local renewable energy sources, especially solar energy. This article presents the deployment and efficiency evaluation of an end-to-end Low Voltage Direct Current (LVDC) nanogrid, from conception to real-world installation within a company. The nanogrid consists of a photovoltaic power plant, a Lithium-Iron-Phosphate (LFP) battery, and DC end-use equipment such as LED lighting and DC fans for two individual offices. An innovation is provided for the power supply and energy management of terminal equipment using the Power Over Ethernet (PoE) standard IEEE 802.3bt. The efficiency of the nanogrid is measured to be 40% higher than the efficiency of an installation powered by PV and distributed at 230 VAC. These results are obtained under certain deployment conditions, which are discussed in this article, in order to enhance the energy efficiency of buildings by using 48VDC. The nanogrid hardware and software infrastructure, the methodology employed for efficiency quantification and the measurement results are described in the paper.

The rapid industrial growth in solar energy is gaining increasing interest in renewable power from smart grids and plants. Anomaly detection in photovoltaic (PV) systems is a demanding task. In this sense, it is vital to utilize recent advances in machine learning to accurately and timely detect different anomalies and condition monitoring. This paper addresses this issue by evaluating different machine learning techniques and schemes and showing how to apply these approaches to solve anomaly detection and detect faults on photovoltaic components. For this, we apply distinct state-of-the-art machine learning techniques (AutoEncoder Long Short-Term Memory (AE-LSTM), Facebook-Prophet, and Isolation Forest) to detect faults/anomalies and evaluate their performance. These models shall identify the PV system's healthy and abnormal actual behaviors. Our results provide clear insights to make an informed decision, especially with experimental trade-offs for such complex solution space.

Accurately predicting the power of solar power generation can greatly reduce the impact of the randomness and volatility of power generation on the stability of the power grid system, which is beneficial for the balanced operation and optimized dispatch of the power grid system, and reduces operating costs. Solar PV power generation depends on weather conditions, which are prone to large fluctuations under different weather conditions. Its power generation is characterized by randomness, volatility and intermittency. Recently, the demand for further investigation and effective use on the uncertainty of short-term solar PV power generation prediction has been getting increasing attention in many application of renewable energy sources. In order to improve the predictive accuracy of output power of solar PV power generation and develop a precise predictive model, the authors worked predictive algorithms for the output power of a solar PV power generation system. Moreover, since short-term solar PV power forecasting is one of the important aspects for optimizing the operation and control of renewable energy systems and electricity markets, this review focuses on the predictive models of solar PV power generation, which can be verified in the daily planning and operation of a smart grid system. In addition, the predictive methods in the reviewed literature are classified according to the input data source used for accurate predictive models, and the case studies and examples proposed are analyzed in detail. The contributions, advantages and disadvantages of the predictive probabilistic methods are compared. Finally, the future studies of short-term solar PV power forecasting is proposed.

This article has been developed to assess the economic feasibility of a roof-top photovoltaic installation of industrial self-consumption. Numerical models that enable an interested person to obtain the main expected parameters will be generated. To do this, a calculation methodology will be generated through which the reader, knowing the location of the facility and dimensions of the roof, will be able to calculate the maximum installable power, the main parameters related to production, the cost of the installation, and the LCOE of the plant. The use of actual costs will be facilitated in case they are known, but it will remain possible to apply the costs of the major equipment (modules, inverter, and structure) considered throughout the article. This developed calculation methodology will also allow a quick comparison of the forecasts of production, CAPEX, and LCOE of plants designed with different inclinations and different types of modules. Consequently, it will be especially useful for decision-making before developing the plant's basic engineering. Moreover, the calculations used for modeling the LCOE will be analyzed in depth. This analysis will allow evaluating how the different technical variables affect the profitability of a photovoltaic installation, such as the selected tilt, the location, the module's technology, or the available area.

The result of the multidisciplinary collaboration of researchers from different areas of knowledge to validate a solar radiation model is presented. The MAPsol is a 3D local-scale adaptive solar radiation model that allows to estimate direct, diffuse and reflected irradiance for clear sky conditions. The model includes the adaptation of the mesh to complex orography and albedo, and considers the shadows cast by the terrain and buildings. The surface mesh generation is based on surface refinement, smoothing and parameterisation techniques and allows the generation of high quality adapted meshes with a reasonable number of elements. Another key aspect of the paper is the generation of a high-resolution digital elevation model (DEM). This high-resolution DEM is constructed from LiDAR data and its resolution if two times more accurate than the publicly available DEMs. The validation process uses direct and global solar irradiance data obtained from pyranometers at the University of Salamanca located in an urban area affected by systematic shading from nearby buildings. This work provides an efficient protocol for studying solar resources, with particular emphasis on areas of complex orography and dense buildings where shadows can potentially make solar energy production facilities less efficient.

Evaluating of long-term satellite-derived ocean color products using in-situ measurements is essential to ensure data quality and integrity. In this study, the Visible Infrared Imaging Radiometer Suite (VIIRS) remote sensing reflectance (Rrs) products were evaluated and analyzed by using long-term OC-CCI in-situ data from 2012 to 2021. The results demonstrate that the root mean square difference of VIIRS Rrs product accuracy in most bands is better than 0.002 (sr-1) when considering its average life span of 12 years. However, the VIIRS Rrs products in shorter wavelength bands (e.g., at 412 nm) had significantly lower accuracy in general and a long-term bias over the recent years. The annual precision of VIIRS Rrs products showed a declining trend especially in coastal or eutrophic waters. This accuracy deterioration of the VIIRS Rrs products suggests a strong need for continuous monitoring of its performance and further efforts on improving the atmospheric correction algorithm to specifically deal with satellite records at high SZAs and OZAs.

Rooftop solar (RTS) projects have the potential to contribute to climate change mitigation and sustainable development objectives. In India, grid-connected RTS capacity has been targeted at 40 GW by the end of the year 2022 however, the installed capacity is limited to 8.2 GW only. As a result, the country missed its 2022 target of installing 100 GW of solar power capacity, largely due to inadequate uptake of RTS. The prevailing practices of RTS implementation is observed to be complex, repetitive, tedious, and time-consuming for potential consumers and there is a lack of coordination among implementing agencies. Therefore, even with vast potential, supportive measures, dedicated policies, and regulations the penetration of RTS systems is far below their respective potential. The introduction of information technology (IT) intervention in the RTS sector would integrate key stakeholders at a single platform so as to reduce the administrative burden of implementing agencies, optimization of processing time, handle multiple consumers simultaneously, and connect consumers with authentic vendors, etc. This would help them to understand and perform their shared roles and responsibilities and enhance the RTS implementation across the state. In this study, the scope for IT interventions in the existing RTS implementation process of the Odisha Renewable Energy Development Agency (OREDA) has been assessed and a simplistic approach has been developed for the execution of the RTS projects in relatively lesser time with the least human interface as well as resources. This approach has been successfully demonstrated with OREDA and a cumulative capacity of around 5 MWp (individual project of 1-2 kWp) residential grid-connected RTS projects implemented through the web platform. Currently, other state nodal agencies are also adopting the model for RTS execution and consumer proliferation through IT interventions.

In this paper, the experimental results of the thermal sub-system of a reliable and cost-effective polygeneration solar system are presented. This polygeneration system produces heating, cooling and electricity from solar energy, which are used in an existing test-building. Heat is generated in four evacuated tube solar collectors (ETC). The heat may be used for space cooling, through a variable geometry ejector (VGE) heat pump. In order to reduce the mismatches between generation and consumption, two thermal storage tanks were added. The performance of a new thermal storage, with 400 l, able to storage both sensible and latent heat, was tested. Heating performances of the test-building were assessed. Ejector cycle tests were also performed.

The aim of this work is to provide a full description of how air temperature and solar radiation induce changes in the land cover over an Antarctic site. We use shortwave broadband albedo (albedo integrated in the range 300-3000 nm) from a spaceborne sensor and from field surveys to calculate the monthly relative abundance of landscape units. Field albedo data were collected using a portable albedometer over seven landscape units: clean fresh snow; clean old snow; rugged landscape composed of dirty snow with disperse pyroclasts and rocky outcrops; dirty snow; stripes of bare soil and snow; shallow snow with small bare soil patches; bare soil. MODIS MCD43A3 daily albedo product was downloaded using the Google Earth Engine API from the 2000-2001 season to the 2020-2021 season. Each landscape unit was characterized by an albedo normal distribution. The monthly relative abundance of the landscape units were calculated by fitting a linear combination of the normal distributions to the histogram of the MODIS monthly mean albedo. The monthly relative abundance of the landscape unit consisting of rugged landscape composed of dirty snow, with dispersed clasts and small rocky outcrops exhibits a high linear positive correlation with the monthly mean albedo (R2=0.87) and a high linear negative correlation with the monthly mean air temperature (R2= 0.69). The increase of the solar radiation energy flux from September to December coincides with the decrease of the relative abundance of the landscape unit composed of dirty snow with dispersed clasts and small rocky outcrops. We propose a mechanism to describe the evolution of the landscape: uncovered pyroclasts act as melting centres favouring the melting of surrounding snow. Ash does not play a decisive role in the melting of the snow. The results also explain the observed decreasing of the thaw depth of the permafrost on the island in the period 2006-2014, resulting from an increase in the snow cover over the whole island.

The energy transition to wind and solar opens opportunities for green hydrogen as the wind and solar generation tends to bring electricity prices down to very low levels. This paper evaluates whether green hydrogen can integrate well with wind and solar PV to help with improved management of the South Australian electricity grid. Green hydrogen can use membrane electrolysis plants during surplus renewable energy periods. This hydrogen can then be electrified or used in industry. The green hydrogen system was analysed to understand the financial viability and technical impact of integrating green hydrogen. We also used systems engineering techniques to understand the system holistically, including the technical, social, environmental, and economic impacts. The results show opportunities for the system to provide seasonal storage, grid firming, and reliability services. Financially, it would need changes to electricity rules to be viable, but without those changes, our modelling suggested it would be financially viable within this decade

One of the most important sources of energy is the sun. Taiwan is located at north 22-25° latitude. Due to its proximity to the equator, it experiences only a small angle of sunlight incidence. Its unique geographical location which can obtain sustainable and stable solar resources. This study takes research on the forecast of solar radiation to maximize the benefits of solar power generation, and develops methods that can predict the future solar radiation pattern to help reduce the costs of solar power generation. This study builds supervised machine learning models, known as deep neural network (DNN) and long short-term memory neural network (LSTM). The hybrid supervised and unsupervised model, namely cluster-based artificial neural network (k-means clustering and fuzzy C-means clustering-based models), was developed. After establishing these models, the study evaluated their prediction results. For different prediction periods, the study selected the best-performing model based on the results and proposed combining them to establish a real-time updated solar radiation forecast system capable of predicting the next 12 hours. The study area covered Kaohsiung, Hualien, and Penghu in Taiwan. Data from ground stations of the Central Weather Administration, collected between 1993 and 2021, as well as the solar angle parameters of each station, were used as input data for the model. The results of this study show that different models have their advantages and disadvantages in predicting different future times. Therefore, the hybrid prediction system can predict future solar radiation more accurately than a single model.

Solar concentration is the ability to harness solar radiation to increase the temperature of a receiver. The receiver is the component into which a heat transfer fluid can be flowed for an ORC system and produce electricity, or it can be used for high-temperature thermal storage, or even to implement thermochemical cycles. The choice of material is critical to ensure optimal performance and long-lasting operation. It is also essential that such material can operate at high temperatures and high thermal gradients. In short, material identification involves high thermal stresses that result in structural deformation. Different metal alloys were used to verify that the yield strength limit was not exceeded due to thermal stress induced by concentrated solar radiation. The problem was implemented in Matlab starting from the general heat equation. The purpose is to test whether thermal stress exceeds the yield strength, which is the condition in which elastic bonds in the material are changed, causing deformation. The best material identified was Inconel 740H, which had a high yield strength value and the lowest temperature difference. Under extreme working conditions, it can withstand thermally induced shocks.

Concentrator photovoltaic (CPV) technology offers an alternative to conventional photovoltaic systems, focusing on the concentration of solar radiation through the optics of the system onto smaller and more efficient solar cells. However, the surface on which the solar beam is incident must remain oriented towards the position of the sun, which requires the use of large and heavy external elements known as solar trackers. In addition to their size, these elements must be as accurate as possible to avoid misalignment. To avoid the need of these solar trackers, the concept of tracking-integrated concentrating systems has been developed. This technology has been researched to make CPV systems accessible in places where conventional systems are not viable, such as building roofs or agrivoltaic fields. This review presents a detailed classification of the existing designs in the literature and providing an overview of this type of system. By eliminating the need for external solar trackers, tracking-integrated CPV systems offer a promising solution to increase the adoption of this technology. Therefore, it is expected that these systems will be a viable and effective option for solar power generation.

The power conversion efficiency (PCE) of polymer solar cells (PSCs) are strongly depended on the bulk-heterojunction active layer. Here, the 1,8-diiodooctane (DIO) additives have been added into the PCDTBT: PC70BM blend PSCs. Based on the higher boiling point than host solvent ODB and better solubility of PC71BM, the device photovoltaic properties with DIO additive were changed obviously. The investigations of EQE indicate that the DIO can influence the charge recombination and transportation process, and absorption studies demonstrate that the charge carriers generation process can also be affected by DIO. The overall impact reflected on the decreased equivalent resistant. With 3% v/v DIO, the Jsc, Voc and FF are both increased. Correspondingly, a highest PCE is achieved of 6.15%, while the reference device without DIO only has a PCE of 5.23%. Hence, adding DIO solvent additive is a effective method for the photovoltaic properties improving of PCDTBT: PC70BM blend PSCs.

Due to increased energy intensive human activities resulting accelerated demand for electric power coupled with occurrence of natural disasters with increased frequency, intensity, and duration, it becomes essential to explore and advance renewable energy technology for sustainability of the society. Addressing the stated problem and providing a radical solution has been attempted in this study. To harvest the renewable energy, among variety of solar cells reported, a composite a-Si/CZTS photovoltaic devices has not yet been investigated. The calculated parameters for solar cell based on the new array of layers consisting of a-Si/CZTS are reported in this study. The variation of i) solar cell efficiency as a function of CZTS layer thickness, temperature, acceptor, and donor defect concentration; ii) variation of the open circuit current density as a function of temperature, open circuit voltage; iii) variation of open circuit voltage as a function of the thickness of the CZTS layer has been determined. There has been no reported study on a-Si/CZTS configuration-based solar cell, analysis of the parameters, and study to address the challenges imped efficiency of the photovoltaic device and the same has been discussed in this work. The value of the SnO2/a-Si/CZTS solar cells obtained from the simulation is 23.9 %.

We revisit the argument that link the efficiency of a solar cell to its reverse operation as a LED, in the case where the material is organic. In organic cells, exciton transport is an intermediate process between sunlight absorption and the generation of electric current. We show that quenching exciton radiation can be beneficial to cell efficiency, without contradicting the general rule prevailing for semiconductor cells. Our treatment allows us to discuss both bulk heterojunction and planar junctions.

One of the major problem of photovoltaic grid integration is limiting the solar-induced imbalances since these can undermine the security and stability of the electrical system. Improving the forecast accuracy of photovoltaic generation is becoming essential to allow a massive solar penetration. In particular, improving the forecast accuracy of large solar farms generation is important both for the producers/traders to minimize the imbalance costs and for the Transmission System Operators to insure stability. In this article, we provide a benchmark for the day-ahead forecast accuracy of utility scale PV plants in 1325 locations spanning the country of Italy. We then use these benchmarked forecasts and real energy prices to compute the economic value of forecast accuracy and accuracy improvement in the context of the Italian energy market regulatory framework. Through this study, we further point out some several important criticisms of the Italian “single pricing” system that brings to paradoxical and counterproductive effects regarding the need to reduce the imbalance volumes. Finally, we propose a new market-pricing rule and innovative actions to overcome these undesired effects of the current dispatching regulations.

The Photovoltaic modules are usually installed on the ground which exposes it to surface deposition of foreign particles. In the Middle East and North Africa region, the primary culprit is dust and sand. They form an insulating and opaque layer on the surface of the glass, which obstructs its heat transfer and optical properties, thereby reducing the overall yield efficiency of the solar panel. Cleaning of this layer is critical to the operation of the solar panel and often requires great effort and energy on a large-scale solar array. In this paper, we propose a novel self-cleaning mechanism for solar panels, with an understanding of the structural integrity of the Photovoltaic laminate and application of external mechanical vibration. By applying an external source of vibration, the solar panels vibrate, excites its fundamental frequencies and cleans by its own. The method is analyzed using finite element analysis method and tested using experiments. Our simulation results based on IEC 61215 show that the maximum principal stress and deformation in the critical layers is within limits. Our experimental results prove the proposed theory is feasible and can be extended to large scale solar arrays. Our proposed method is retrofittable and could save money, energy and effort in cleaning the solar arrays, which can replace current techniques.

The fact that Thailand’s energy policy has set a new renewable energy target of 30% of total final energy consumption by 2036. It also has the potential of solar energy and community demands in remote areas. However, most of the renewable energy technology will still be able to achieve renewable energy goals, similar to the case of the national policy that promotes Solar Home System (SHS) in remote areas, lack of good handling. Therefore, achieving the goal of the renewable energy policy should be in position using the right strategy. This article presents the result of a case study in the Akha upland community, northern Thailand, where we used the mixing method and factor analysis to analyze strategies for SHS related criteria. The key scopes and challenge included bottom-up planning concepts and subsidies from expert persons, while contributions to factors have an impact on developing sustainable SHS, include the creating approval of SHS technologies, developing of SHS management, promoting of SHS technologies, and supporting of SHS policies, respectively. Mainly, social factors provide positive effects, which thus influence the sustainable development of process SHS in terms of the creation of approval. Furthermore, there should be managed appropriately for each community, for the positive imagery of solar power.

Band-gap alignment engineering has now been extensively studied due to its high potential application. Here we demonstrate a simple route to synthesize two metal oxide layers and align them together according to their bandgaps on surface of crystalline silicon (c-Si) solar cells. The metal oxide layers can not only extend absorption spectrum to generate extra carriers but also serve to separate electron-hole pairs more efficiently. As a consequence, the photovoltaic performance of SnO₂/CdO /Si double-layer solar cell (DLSC) is highly improved compared to CdO/Si and SnO₂/Si single-layer solar cells(SLSCs) and SnO₂/CdO/Si double-layer solar cell (DLSC). By the alignment engineering, the SnO₂/CdO/Si DLSC produces a short circuit photocurrent (J_sc) of 38.20 mA/cm², an open circuit photovoltage (V_oc) of 0.575 V and a fill factor (FF) of 68.7%, corresponding to a light to electric power conversion efficiency (η) of 15.09% under AM1.5 illumination. These results suggest that with the use of metal oxide layers by band-gap alignment engineering, new avenues have been opened for developing high-efficiency and cost-effective c-Si solar cells.

The reckless use of non-replenishable fuels by the growing population for energy and the resultant incessant emission of hazardous gases and waste products into the atmosphere insisted scientists to fabricate materials capable of managing these global threats at once. In recent studies, photo-catalysis employed focus on utilizing renewable solar energy to initiate chemical processes with the aid of semiconductors and highly selective catalysts. A wide range of nanoparticles have showcased promising photocatalytic properties. Ultrasmall metal nanoclusters (MNCs) with sizes below 2 nm, stabilized by ligands shows discrete energy levels, exhibits unique optoelectronic properties which are vital to photocatalysis. In this review, we intend to compile information on varying photocatalytic efficiency of metal NCs with respect to changes in their properties. Review discusses about the photocatalytic activity of atomically precise ligand-protected MNCs and its hybrids in the domain of in energy conversion processes like photodegradation of dyes, Oxygen Evolution Reaction (ORR), Hydrogen Evolution Reaction (HER) and CO2 Reduction Reaction (CO2RR), and photosensitizer in solar cell.

The use of vitamin D (VitD) supplements has become widespread in the last decade due not only to the dissociation between the blood levels recommended as "optimal" and those shown by the healthy population, but also to its presumed beneficial effects on multiple disorders. This work evaluated the levels of 25-hydroxyvitamin D [25(OH)D] in a healthy population of European origin living in a region with high solar irradiation. In serum samples from a population-based study conducted in the Canary Islands, levels of 25(OH)D were analyzed. In 876 individuals who had no history of kidney or malabsorption disorders and who had not been treated with calcium and/or VitD supplementation, the median 25(OH)D level was 26.3 (5th;95th percentile, 14.3;45.8)ng/mL. Notably, 65.4% of the population had 25(OH)D blood levels below 30ng/mL, 23.4% below 20ng/mL and 6.4% below 15ng/mL. Based on the lack of evidence supporting causality between 25(OH)D levels below what is recommended as optimal (≥20ng/mL, or even ≥30ng/mL) and major skeletal and non-skeletal diseases, and in light of the distribution of the concentration of this vitamin in healthy adults living under optimal conditions of solar irradiation, it seems reasonable to consider 25(OH)D levels below 20ng/mL and close to 15ng/mL as adequate for the general population.

As the first initiative of its kind in Algeria, here is presented a solar-powered mobile “Ultraviolet Germicidal Irradiation” disinfection unit (UVGI) based on a special germicidal ultraviolet-C (UVC) radiator. The system was designed to disinfect several objects such as: medical tools, reusable masks, face-shields, gloves, phones, laptops, keys, money and many other portable devices that need to be disinfected/sterilized. It offers the advantage of complete autonomy through the built-in photovoltaic (PV) system that includes a solar panel, a gel battery, a charge controller and a power inverter. The system provides an extra 220V-50Hz outlet with 375VA maximum power to be used when energy is needed. The system is easily scalable to generate higher ultraviolet dosages by adding more UVC lamps. The chemical-free germicidal UVC sanitizing method employed by this device effectively disactivates a very wide range of microorganisms (microbes, bacteria and fungi and viruses including the actual SARS-CoV-2 that causes COVID-19 respiratory disease) and it has several advantages in comparison to chemical-based sanitizing methods. The total cost to make this open source device is below 1000 € and is easily customizable and scalable. This device is an open source, secure and fast equipment for objects and surface disinfection. The device will be fully automated by adding PIR sensors or remote control after further funding will be received.

The power system has rapidly grown and expanded over the past decades and has been experiencing major changes and challenges. The increase in energy demand and the modern advancements in the smart grid, such as solar and wind energies and electric vehicles, have led to complexity and complications for utilities. A further layer of complexity and difficulty was added by the rapid expansion of behind-the-meter (BTM) photovoltaic (PV) systems with various designs and characteristic features. The rapid increase and the invisible solar power (BTM) have led to fluctuations in power grid stability and reliability and to inefficiency. Accurate forecasting of load generation will help to assure optimal planning, minimize the negative effects of the PV systems, and minimize the operational and maintenance costs. The authors propose a solution that uses combinations of K-means clustering with neural network machine learning models, AMI real-world PV load generation, and weather data to forecast the generation load at customer locations to achieve a 2.49% error between actual and predicted generation load.

Chinese investors are easily affected by hot topics on the media and Internet and likely take irrational behavior. They tend to consume rationally and invest emotionally. This research aims to analyze the Baidu index’s effect on share price of solar power industry in China. Three main models are established to identify the correlation between Baidu index and stock price of solar industry. The media index and searching index of Baidu are chosen as an independent variable to measure the influence from media and Internet, and stock price as the dependent variable. To improve and complete the analysis, Hexun index is taken into consideration as mediator variable. This study applied Multiple Linear Regression Model and VAR (Vector auto-regression) Model. The research mainly uses the tools of SPSS, Eviews and Excel to conduct data analysis. The test is based on the theories of Granger Causality, unit root test, F-test, and t-test. The research proves the relationship between the close price of stock and Baidu index, and it also created a model for further forecasting.

Compound parabolic concentrators are relevant systems used in solar thermal technology. With adequate tailoring, they can be used as an efficient and low-cost alternative in residential water applications. This work presents a simulation study using a ray tracing methodology. With this technique we simulate the interaction between solar rays and solar concentrator to quantify the amount of energy that impinges on the receiver at a particular time. Energy availability is evaluated in a comparison of two configurations: stationary at 21° throughout the year and multi position setup; tilted with respect to the horizontal depending on three seasonal positions: 0° for summer, 16° for spring / autumn and 32° for winter, with the objective of increasing the amount of available energy in each season. The fact that a tracking system can be dispensed with also represents an economical option for the proposed application. The results showed that at 21°, the proposed system works satisfactorily; however, by carrying out the selected angular adjustments, the overall energy availability increased by 22%, resulting in a more efficient option. The methodology developed herein proved to be a valuable tool for prototype design and performance evaluation.

Well-intentioned regulations to protect Canada’s most productive farmland restrict large-scale so-lar photovoltaic (PV) development. The recent innovation of agrivoltaics, which is the co-development of land for both PV and agriculture, makes these regulations obsolete. Burgeoning agrivoltaics research has shown agricultural benefits including increased yield for a wide range of crops, plant protection from excess solar energy and hail, improved water conservation while maintaining agricultural employment and local food supplies. In addition, the renewable electricity generation decreases greenhouse gas emissions while increasing farm revenue. As Canada in general, and Ontario in particular, is at a strategic disadvantage in agricultural without agrivoltaics, this study investigates the policy changes necessary to capitalize on the benefits of using agrivoltaics in Ontario. Land use policies in Ontario are reviewed. Then, three case studies (peppers, sweet corn and winter wheat) are analyzed for agrivoltaic potential in Ontario. These results are analyzed in conjunction with potential policies that would continue to protect the green-belt of the Golden Horseshoe, while enabling agrivoltaics in Ontario. Four agrivoltaic policy areas are discussed: increased research and development, enhanced education/public awareness, mechanisms to support Canada’s farmers converting to agrivoltaics and using agrivoltaics as a potential source of trade surplus with the U.S.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

The adsorption of surfaces exposed to sunlight results in increased temperature that can cause physical damage and increase in energy consumption. The infrared reflective coatings that keep objects cooler have significant benefits in a wide variety of application by reflecting the infrared lights, reducing the operating costs, improving energy efficiency of buildings and vehicles (roofs, walls and windows), extend the objects’ lifespan. Our research focused on the elaboration of coatings with minimum adsorption in the infrared wavelength range. This was achieved by production of coatings that have infrared transparent and infrared reflective ability. The infrared reflection and surface warm up was investigated in the function of concentration and composition of pigments in the coatings. With investigation of different coating compositions the pigments and the binding systems were optimized. The coatings with different compositions were characterized by total solar reflection in the UV, visible and infrared wavelength range as well as by infrared reflection. Different coatings were produced in RAL7016 anthracite green color but with much better infrared reflectance, transparency as well as with heat reflectance.

This study advances the field of solar irradiance nowcasting by introducing a discrete-level classification approach, diverging from traditional continuous measurement methods. Grounded in a need for cost-effective and modular solutions, the research employs high-resolution computer vision coupled with a deep learning framework to predict Direct Normal Irradiance (DNI). By harnessing the capabilities of a Logitech C900 1080p HD camera and an NVIDIA Jetson module, the study achieves real-time data processing, pivotal for CSP systems' operational efficiency. The core of the methodology is the ResNet-50 convolutional neural network, refined via transfer learning on a bespoke dataset, culminating in a predictive accuracy of 85.78%. This discrete classification model contrasts with conventional, costly instruments like the MS-57, offering a novel and accessible alternative for DNI estimation. Such innovation not only demonstrates high predictive accuracy but also signifies a shift towards less resource-intensive and more adaptable solar energy forecasting tools, contributing a significant leap towards optimizing renewable energy systems.

This paper, we examined the technology to maximize the use of renewable energy. The passive ventilation system is expected to reduce the energy consumption of the fan power and the maintenance burden. In addition, the wall-mounted solar air heater can supply thermal energy without using any energy at all. Therefore, we propose a "passive ventilation system with a solar air heater" that combines a passive ventilation system with solar air heater to preheat the air supply and reduce the ventilation load. To evaluate the solar air heater performance in a real environment, we developed a simulation for calculating the heat collection capacity of the solar air heater, and then implemented the system in a real building for verification. Based on the measurement results, the effects of heating load reduction and prediction methods are presented.

Solar3D is an open-source software application designed to interactively calculate solar irradiation at three-dimensional (3D) surfaces in a virtual environment constructed with combinations of 3D city models, digital elevation models (DEMs), digital surface models (DSMs) and feature layers. The GRASS GIS r.sun solar radiation model computes solar irradiation based on two-dimensional (2D) raster maps for given day, latitude, surface and atmospheric conditions. With the increasing availability of 3D city models and demand for solar energy, there is an urgent need for better tools to computes solar radiation directly with 3D city models. Solar3D extends GRASS GIS r.sun from 2D to 3D by feeding the model with input, including surface slope, aspect and time-resolved shading, that is derived directly from the 3D scene using computer graphics techniques. To summarize, Solar3D offers several new features which, as a whole, distinguish itself from existing 3D solar irradiation tools: (1) the ability to consume massive heterogeneous 3D city models, including massive 3D city models such as oblique airborne photogrammetry-based 3D city models (OAP3Ds or integrated meshes); (2) the ability to perform near real-time pointwise calculation for duration from daily to annual; (3) the ability to integrate and interactively explore large-scale heterogeneous geospatial data. (4) the ability to calculate solar irradiation at arbitrary surface positions including at rooftops, facades and the ground. Solar3D is publicly available at https://github.com/jian9695/Solar3D.

The cutting-edge photovoltaic cells are an indispensable part of the ongoing progress of earth-friendly plans for daily life energy consumption. However, the continuous electrical demand that extends to the night time requires a prior deployment of efficient real-time storage systems. In this regard, metal-air batteries have presented themselves as the most suitable candidates for solar energy storage, combining extra lightweight with higher power outputs and promises of longer life cycles. Scientific research over non-precious functional catalysts has always been the milestone and still contributing significantly to exploring new advanced materials and moderating the cost of both complementary technologies. Metal-organic frameworks (MOFs) derived functional materials have found their way to the application as storage and conversion materials, owing to their structural variety, porous advantages, as well as the tunability and high reactivity. In this review, we provide a detailed overview of the latest progress of MOF-based materials operating in metal-air batteries and photovoltaic cells.

We report on the field testing datasets and performance evaluation results obtained from a commercial property-based visually-clear solar window installation site in Perth-Australia. This installation was fitted into a refurbished shopping centre entrance porch, and showcases the potential of glass curtain wall-based solar energy harvesting in built environments. In particular, we focus on photovoltaic (PV) performance characteristics such as the electric power output, specific yield, day-to-day consistency of peak output power, and the amounts of energy generated and stored daily. The dependencies of the generated electric power and stored energy on multiple environmental and geometric parameters are also studied. An overview of the current and future application potential of high-transparency, visually-clear solar window-based curtain wall installations suitable for practical building integration is provided.

Several studies have shown that changes in incoming solar radiation and variations of the diffuse fraction can significantly modify the vegetation carbon uptake. Hence, monitoring the incoming solar radiation at large scale and with high temporal frequency is crucial for this reason along with many others. The EUMETSAT Satellite Application Facility for Land Surface Analysis (LSA SAF) operationally disseminates in near real time estimates of the downwelling shortwave radiation at the surface since 2005. This product is derived from observations provided by the SEVIRI instrument onboard the Meteosat Second Generation series of geostationary satellites, which covers Europe, Africa, the Middle East, and part of South America. However, near real time generation of the diffuse fraction at the surface level has only recently been initiated. The main difficulty towards achieving this goal was the general lack of accurate information on the aerosol particles in the atmosphere. This limitation is nowadays less important thanks to the improvements in atmospheric numerical models. This study presents an upgrade of the LSA-SAF operational retrieval method, which provides the simultaneous estimation of the incoming solar radiation and its diffuse fraction from satellite every 15 minutes. The upgrade includes a comprehensive representation of the influence of aerosols based on physical approximations of the radiative transfer within an atmosphere-surface associated medium. This article explains the retrieval method, discusses its limitations and differences with the previous method, and details the characteristics of the output products. A companion article will focus on the evaluation of the products against independent measurements of solar radiation. Finally, the access to the source code is provided through an open access platform in order to share with the community the expertise on the satellite retrieval of this variable.

We consider the restrictions on photovoltaic (PV) capacity that are caused by limitations on where panels can be sited, and find quantitative evidence for the need for high efficiencies. We define 15% of the UK’s energy consumption as a “significant” contribution and, with London as an exemplar, we perform an idealised calculation that makes the most optimistic possible assumptions about the capabilities of future PV technologies, and use published surveys of energy usage, dwelling type and insolation. We find that covering every UK domestic roof with the highest power-conversion efficiency (PCE) solar panels currently commercially available, could produce up to 9% of the UK's energy. A 15% contribution would require PV technologies with >37% PCE, more than the theoretical Shockley-Queisser limit. Replacing the idealising assumptions with more realistic estimates increases this by 2-3 times. Alternatively, a solar farm using the currently available PCEs would require a politically challenging ~1200km2 of new land, roughly the area of Greater London, for this 15% contribution. We conclude that PCEs must be driven higher even than the Shockley-Queisser limit for PV to play a significant part in carbon mitigation.

The growing urgency for sustainable energy solutions necessitates a deeper understanding of the environmental impacts of renewable technologies. This article aims to synthesize and analyze Life Cycle Assessments (LCA) in this domain, providing a comprehensive perspective. We systematically categorize 2,923 articles into four communities: (1) Photovoltaic systems, (2) Wind energy systems, (3) Materials for auxiliary industry of photovoltaic and wind systems, and (4) Solar thermal systems. A comparative analysis is conducted to identify methodological consistencies and disparities across these communities. The findings reveal diverse methodological approaches and a range of environmental impacts, highlighting the complexities in assessing renewable energy systems. The article underscores the significance of material selection in photovoltaic and wind systems, providing a critical overview of the current state of LCA research in renewable energy and stressing the need for standardized methodologies. It also identifies gaps in recent research, offering insights for future studies focused on integrating environmental, economic, and social considerations in renewable energy assessments.As a case study, an LCA was used to evaluate two energy supply methods for a sensor network: one connected to the public grid and another powered by a photovoltaic panel. The off-grid system, while more environmentally friendly by reducing reliance on non-renewable energy sources, posed challenges due to the high environmental impact of battery production and disposal. Integrating environmental assessments provides a robust framework for making informed decisions on sustainable technologies. The findings are critical for projects that balance technological needs with sustainability goals.

The present study describes the development and application of a computer model of the national electricity system for the Caribbean dual-island nation of Antigua and Barbuda to investigate the cost-optimal mix of solar photovoltaics (PV), wind, and in the most novel contribution, concentrating solar power (CSP). These technologies, together with battery and hydrogen energy storage, can enable the aim of achieving 100% renewable electricity and zero carbon emissions. The motivation for this study was that while most nations in the Caribbean rely largely on diesel fuel or heavy fuel oil for grid electricity generation, many countries have renewable resources beyond wind and solar energy. Antigua and Barbuda generates 93% of its electricity from diesel-fueled generators and has set targets of becoming a net-zero nation by 2040 and having 86% renewable energy generation in the electricity sector by 2030, but the nation has no hydroelectric or geothermal resources. The modeled, optimal mix of renewable energy technologies presented here was found for Antigua and Barbuda by assessing the levelized cost of electricity (LCOE) for systems comprising various combinations of energy technologies and storage. Other factors were also considered, such as land use and job creation. It was found that 100% renewable electricity systems are viable and significantly less costly than current power systems, and that there is no single defined pathway towards a 100% renewable energy grid, but several options are available.

Excess energy from photosynthesis can be collected through biophotovoltaic platforms to generate green electrical power. This research evaluated the in-situ performance of different CAM (Crassulaceae acid metabolism) plants from Calama city located in the Atacama Desert for energy recovery as biophotovoltaic cell (BPV) using AISI 316L and Cu as electrodes. The species evaluated were Aloe perfoliata, Cereus jamacaru, Austrocylindropuntia subulata, Agave potatorum, Malephora crocea, and Kalanchoe daigremontiana. The results indicate that K. daigremontiana can be used as in-situ BFV because it has a maximum cell potential of 0.248 V and a minimum of 0.139 V with a recurrence close to 89% in the ranges [0.2 - 0.25] V. This is one of the few investigations that evaluate the potential of native CAM plants as BFV energy sources, providing new knowledge for the development of sustainable alternatives for horticultural crop production systems.

The pointing accuracy of large radio telescopes is affected by antenna structure errors, installation errors, servo errors, gravity, and varying environmental factors. It is hard to estimate the pointing error of radio telescopes under solar radiation via the traditional multi-parameter static pointing models, due to the time-varying characteristics of the dynamic pointing error. There is still no effective way to estimate the dynamic pointing error of large radio telescopes under solar radiation up to now. To estimate the dynamic pointing error of large radio telescopes under solar radiation, a new way based on digital twin(DT) is tried in this paper. The operational framework of the DT system of large radio telescopes is introduced first. Then, the Wuqing 70-m radio telescope(WRT70) is taken as the research object, the digital models of which are created. Finally, the reliability of the WRT70's DT system is verified and the dynamic pointing error of WRT70(staying at the position of the elevation angle of 90° and the azimuth angle of 180°) on two sunny days in different seasons is estimated by the created DT system. The research results show that the pointing error of large radio telescopes under solar radiation fluctuates greatly and the seasonal differences are very striking. The maximum elevation pointing error of WRT70 under solar radiation around the winter solstice is over 40 arcsec, which should never be ignored. The way is feasible to estimate the dynamic pointing error of large radio telescopes staying at a specific position under solar radiation via constructing a DT system in this paper, but it is not yet able to estimate effectively the dynamic pointing error of large radio telescopes being in action. It is expected to establish a dynamic pointing error model and calibrate the dynamic pointing errors of large radio telescopes being in action by DT technology in the future.

Technological advancements must keep pace with earth’s rising demand for energy, while minimizing the carbon footprint on earth. One such option is using space based solar (SBS) radio frequency (RF) microwave power beaming. This innovative and novel technology is currently being explored to address terrestrial photovoltaic (PV) intermittency and provide a method to transmit power to other spacecraft in various orbits. This modality of power generation and distribution presents a new way to power terrestrial off-grid applications and earth orbiting spacecraft. In 1968, Dr. Peter Glaser published "Power from the Sun: Its Future", which serves as the foundation of this paper to revitalize scientific interest and efforts in this topic. This paper will primarily focus on the reliance of SBS initiatives on reusable launch vehicles (RLV) to place SBS spacecraft in a designated orbit, as well as the technological, economic, and operational challenges associated with power beaming to earth and other spacecraft. This includes a discussion of the variables from the operational environment that contribute or accelerate spacecraft end of life.

The transition region is a very thin but most peculiar layer in the solar atmosphere, located between the solar chromosphere and the corona. It is a key region for understanding the coronal heating, the solar eruptions triggering, and the origin of solar winds. Here, the gradients of all physical parameters are very high, including plasma density, ionization degree, temperature, and magnetic fields, etc. Therefore, the transition region should be highly dynamic, such as fast energy releasing and transporting, plasma heating, and even particle accelerating. They include two physical aspects: thermal and non-thermal processes. The thermal processes can be observed from the ultraviolet (UV) and extreme ultraviolet (EUV) emission by multi-wavelength images. The non-thermal processes, however, should be related to radio emissions especially at millimeter wavelengths, and the frequency range should span from several GHz to beyond 300 GHz, and the emission mechanism should be highly related to the magnetic fields and variations. The ultra-wide broadband spectral observations at millimeter wavelengths with high spectral resolutions may provide rich dynamic information about the transition region, such as non-thermal energy release and transmission, the flows of plasma and energetic particles, the magnetic fields and their variations, the generation and transportation of various waves, and the formation and evolution of the source regions of solar eruptions. Here, we discussed the spectral characteristics of millimeter-wave emission from the transition region and proposed a new conception of ultra-wide broadband millimeter-wave spectrometers to observe them.

This paper is devoted to the analysis of fluctuations in the solar wind plasma and interplanetary magnetic field parameters observed by Solar Orbiter and WIND spacecraft at different scales, ranging from ~10^3 to 10^7 km. We investigated two long observation intervals when the spacecraft were near the Sun-Earth line, during which the distance between the spacecraft was 0.1 and 0.5 AU respectively. It is analyzed how the fluctuation properties in different types of SW, associated with quasi-stationary and transient solar phenomena, transform on the way from the Sun to the Earth. It is shown that the time series behavior of the bulk speed subject to the least change even at the large distance between the observation points, while the time series of the IMF magnitude, components and proton density were significantly transformed even at the relatively short distance. Regardless of the assumed change in the absolute value of the parameters, the conducted statistical analysis shows that the characteristics of their fluctuations (including the level of intermittency) remains near constant regardless of the distance between the observation points and depends mostly on the type of the solar wind.

Currently there are strong and sustained growth trends observed in multi-disciplinary industrial technologies such as building-integrated photovoltaics and agrivoltaics, where renewable energy production is featured in building envelopes of varying degrees of transparency. Novel glass products can provide a combination of thermal energy savings and solar energy harvesting, enabled by either patterned-semiconductor thin-film energy converters on glass substrates, or by using luminescent concentrator-type approaches to achieve high transparency. Significant progress has been demonstrated recently in building integrated solar windows featuring visible light transmission of up to 70%, with electric power outputs of up to Pmax ~ 30-33 Wp/m2. Several slightly different designs were tested during 2021-2023 in a greenhouse installation at Murdoch University in Perth, Western Australia. The objective of this paper is to report on the field performance of these PV windows in the context of agrivoltaics, and to provide some detail of the performance differences measured in several solar window designs related to their glazing structure materials. Methods for the identification and quantification of long-term field performance differences and energy generation trends in solar windows of marginally different design types are reported. The paper also aims to outline the practical application potential of these transparent construction materials in built environments, focussing on the measured renewable energy figures and seasonal trends observed during the long-term study.

Electric energy is one of the driving forces in every country. The supply of electrical energy continues to present various challenges, such as high costs associated with procuring raw materials for generation, sparsely populated areas that are not connected to the main grid, and the need for infrastructure to support generation and network delivery. These challenges have contributed to the growing adoption of renewable energy sources, particularly solar photovoltaics (PV).In this study, we have developed a practical method to assess the spatial PV potential in a selected urban area. The methodology combines data collected from an unmanned aerial vehicle (UAV) photogrammetry, Geographic Information System (GIS), and the energy output from three remote photovoltaic systems installed at different locations. The results obtained from this approach not only provide the energy generated per square meter, per year (kWh m-2 yr-1), but also provides a base to calculate the potential distance that electric cars could travel based on the energy generated. To illustrate the application of this method, two practical cases were selected: Senglea, Malta, and Munxar, Gozo. These examples highlight the versatility and effectiveness of our approach for evaluating and harnessing solar energy through photovoltaic panels in different contexts.

Herein we foremost detailed the numerical modeling of the double absorber layer- methyl ammonium lead iodide– carbon nitride layer solar cell and subsequently provided in-depth insight on the active layer associated with dominant radiative and non-radiative recombination losses limiting the efficiency ( ) of the solar cell. Under recombination kinetics phenomena, we explored the influence of Radiative recombination, Auger recombination, Shockley Read Hall recombination, the energy distribution of defects; Band Tail recombination (Hoping Model), Gaussian distribution, metastable defect states including single donor (0/+), single acceptor (-/0), Double Donor (0/+/2+), double acceptor (2/-/0-), and the interface layer defects on the output characteristics of the solar cell. Setting defect (or trap) density to with uniform energy distribution of defects for all the layers, we achieved the of 24. 16 %. A considerable enhancement in power conversion efficiency was perceived as we reduced the trap density to for the absorber layers. Further, it was observed that for the absorber layer with double donor defect states, the active layer should be carefully synthesized to reduce crystal order defects to keep the total defect density as low as to achieve efficient device characteristics

: Solar sails use radiation from the sun to generate thrust without any fuel or propellant. Since this is a form of propulsion that has theoretically infinite use, we would like to test its capability on long-term missions by simulating a spacecraft equipped with solar sails to the Sun-Earth L5 Lagrange point. To control the sail angle, which is the main form of control we have over the sail’s performance, we will devise a form of optimal control based on Pontryagin’s Minimum Principle. Simulating the dynamics in MATLAB SIMULINK, we find that such a control method relies on iterating over initial conditions for the co-states to find the necessary parameters for the trajectory to reach the desired point. Therefore, an autonomous control scheme that uses this form of optimal control will need a way to numerically find said initial conditions in order to find the control angle needed at any point in time, which may be computationally intensive.

Interface solar steam generation (ISSG) are charming for its applications in desalination and wastewater treatment. Biomass is an attractive substrate for utilizing solar vapor evaporators because of its natural pore structure and water transportability. Polymers like polydopamine (PDA) and polypyrrole (PPy) with broadband spectrum absorption are fascinating in photothermal materials (PTMs). Herein, PDA coated daikon-based (PDA-DK) and PPy coated daikon-based (PPy-DK) PTMs have been exploited for solar steam generation. When polyethylene foam (PEF) was used as an insulating layer to limit heat loss from the PTMs to bulk water, the evaporation rate of PDA-DK and PPy-DK was raised from 0.82 kg m–2 h–1 and 0.96 kg m–2 h–1 to 1.50 kg m–2 h–1 and 1.60 kg m–2 h–1, respectively. Meanwhile, the corresponding photothermal conversion efficiency was increased to 89.01% and 98.97%, which was increased by nearly 40% under 1-sun irradiation. In addition, PDA-DK and PPy-DK exhibited remarkable stability for the solar steam generation without significant change through 15 cycles. Furthermore, PDA-DK and PPy-DK could effectively desalt seawater and purify dyeing wastewater. All the results indicate that PDA-DK and PPy-DK have great potential in real-world applications for solar steam generation.

Developing new technologies is essential for advancement in solar cell technologies due to their ability to only absorb light mainly in the visible light spectrum. Super crystals Nd³⁺- Eu³⁺ optical characteristics display higher absorption of light waves than single crystals of Eu³⁺ and Nd³⁺ due to a two-photon absorption energy transfer mechanism known as upconversion. Super crystals Nd³⁺- Eu³⁺ display higher absorption due to fewer light waves being transmitted through materials as reported in spectra data. Transmission spectra data reflects that Nd³⁺- Eu³⁺ nanoparticles are great candidates to enhance light absorption in solar cell devices.

This study aimed to focus on how to design a low-cost greenhouse for the cultivation of crops, to propose the cost-effectiveness analysis of small agribusiness, and to promote sustainable agricultural production during and after the COVID-19 crisis for helping grassroots and anyone who lost their job. This article is qualitative engineering research, studying of literature reviews of greenhouse farming concept and Micro, Small and Medium Enterprises, then, designing low-cost greenhouse model which was preliminarily adapted for hot climate countries. Three plants that were selected as representative plants of this model include sunflower, water spinach, and wheat. The greenhouse model, measuring 5 x 7 x 4 m (W x L x H), was designed for this mission. The total cost of one building is approximately 97,994 THB. For the worthiness of the investment, farmers should build at least three greenhouse buildings, which will return total income to farmers approximately 34,666.09 THB per month. The suggestion includes further knowledge and financial supports from the government sectors among farmers, then, boost them up using high-level technology and also planting high-price agribusiness production to promote the local economy to be strong and sustainable.

Solar Insolation is the major contributor of earth’s radiation and energy budget. The insolation reaching the surface is a prime input for eco-physiological processes such as evapotranspiration and photosynthesis. Therefore, it is as critical component to assess bio-energy and bio-fuel resources. It is also a crucial input to crop simulation model for yield forecasting and its further applications in solar energy solutions. Although ground observations are better for accuracy purpose, they have challenges of maintenance, regular calibration and upkeeping etc. This call for the continuous spatio-temporal satellite based observations barring the acceptable accuracy. In case of INSAT3D/3DR, Bhattacharya et al. (2015) have derived the surface insolation product which is being used widely. We propose a method of improvement in this product. It is envisaged that a correction applied with the help of ground truth estimates may enhance the utilization of insolation products derived from INSAT3D/3DR datasets. In the present study, surface insolation product derived from INSAT 3D/3DR data at an interval of 30 minutes each (collectively 15 minutes interval) with 4 km spatial resolution was used for duration from May-2017 to Apr-2019 over Nagpur. Ground truth observations for same duration were carried out with CNR4, which were used to correct the INSAT 3D/3DR surface insolation product using the statistical best-fit method. Corrected INSAT 3D/3DR products are found correlating with the ground values well with differences of approximately < 1 W/m2. Best-fit parameters evolved in the present study uses only 2 years of simultaneous ground and satellite data which can be further improved by multi-year data base. We propose better utilization of INSAT 3D/3DR based surface insolation products in the assessment of solar resource mapping over Nagpur (and possibly other regions, such as Bhandara) with the help of best-fit parameters as assessed in the present study.

Perovskite based solar cells have achieved tremendous progress reaching record efficiency in the past 5 years. Numerous new processes and chemistry have been reported and contribute to the perovskite rapid progress. Continuous efficiency improvements are still necessary for perovskite solar cells, and an exploratory data analysis on devices performance over multiple studies could boost the technology development. Such analysis could identify patterns or provide insights that are not obvious in a single study. Here we present a high quality dataset containing only independently certified Pb-based perovskite solar cells summarizing their efficiency, relevant I-V metrics, manufacturing processes and materials used. Analysis over the dataset provides insights on how aperture size, perovskite deposition methods and materials used in each functional layer affect the final solar cell efficiency and I-V metrics. Future directions are also suggested for efficiency improvements.

The high environmental impact of conventional methods of cooling and heating has increased the need for renewable energy deployment for covering thermal loads. Towards that direction, the proposed system aims at offering an efficient solar powered alternative, coupling a zeolite-water adsorption chiller with a conventional vapor compression cycle. The system is designed to operate under intermittent heat supply of low-temperature solar thermal energy (<90 °C) provided by evacuated tube collectors. A prototype was developed and tested in cooling mode operation. The results of separate components testing showed that the adsorption chiller was operating efficiently, achieving a maximum coefficient of performance (COP) of 0.65. With respect to the combined performance of the system, evaluated on a typical week of summer in Athens, the maximum reported COP was approximately 0.575, mainly due to the lower driving temperatures at a range of 75 °C. The corresponding mean energy efficiency ratio (EER) obtained was 5.8.

Universitas Gadjah Mada (UGM) is implementing the concept of green campus by various means including through elements in its sustainable campus development plan. With regards to several factors related to Energy and Climate Change indicators set by UI GreenMetric, this research examined the existing condition of the area of UGM which belongs to academic zone in order to construct a proposal based on a building mass reconfiguration. This proposal was aimed to improve the implementation of energy-specific green campus concept within the Forestry cluster area as a sample case study. This selection was based on the average value of the Building Coverage Ratio (BCR) values in all of the clusters; thus, the scenario was relevant for generalization and could be replicated in other clusters in the university. The study was done in three stages of simulation, and was based on a series of digital simulation of sunlight hour and solar radiation run in Grasshopper using Lady Bug environmental analysis plug-in for a period of five summer months during the building office hours. Following the reconfiguration, results had shown a similar downtrend between the amount of sunlight hour and solar radiation in the area (up to 49% and 45% respectively on building envelopes, and up to 44% and 42% respectively on landscaping surfaces). This reduction indicated a potential of energy efficiency by applying selective building mass reconfiguration as a passive design strategy that goes hand in hand with the campus’s development policy to optimize the use of BCR for a greener UGM campus through its many undergoing and upcoming redevelopment projects.

In this paper, by developing a mathematical model, the operating temperature of perovskite solar cells (PSCs) under different operating conditions has been calculated. It is found that by reducing the density of tail states at the interfaces, acting as recombination centres, through some passivation mechanisms, the operating temperature can be reduced significantly at higher applied voltages. The results show that if the density of tail states at the interfaces is reduced by three orders of magnitude through some passivation mechanisms, then the active layer may not undergo any phase change up to an ambient temperature 300 K and it may not degrade up to 320 K. The calculated heat generation at the interfaces at different applied voltages with and without passivation shows that the heat generation can be reduced by passivating the interfaces. It is expected that this study may provide a deeper understanding of the influence of interface passivation on the operating temperature of PSCs.

Two region asymmetric polymers PR2F and PR1F with three repeat units of A-D-A, π-D-A, and π-D-π along the polymer backbone were attained by polymerizing different fluorinated benzothiadiazole-thiophene units, FBT-T and 2FBT-T units (A–π), with benzodithiophene unit (D), respectively. Here, the new region asymmetric polymers were in contrast to the traditional polymers featuring a D–A or D–π–A–π backbone. Both the region asymmetric polymers showed a low lying of HOMO energy level in relation to that of the PC61BM acceptor and then obtained the high open-circuit voltage of ~1 V in both PR2F and PR1F devices. Bulk-heterojunction devices based on PR2F with difluorinated BT exhibited an appreciable power conversion efficiency (PCE) of 4.73% due to the relatively high and balanced charge carrier mobilities, while the mono-fluorinated BT polymer PR1F-based devices gave a lower PCE of 2.92%. These results indicate that the region asymmetric conjugated polymer is a promising class of materials for polymer solar cell applications, and it is significant to further understand the influence of polymer structure on optoelectronic properties.

Today with enhancement in technology, sciences, there is also an increase in global heating rate. There is an urgent need of any alternate efficient source to reduce the wastage of energy and to utilize it efficiently. The advanced preparation of Expanded graphite ,lauric acid, stearic acid as shape stabilized phase change material deals with different energy harvesting applications. The main reason behind the need for synthesis of this matrix is to prepare a material that can be used in low temperature energy storage applications. Mixture of lauric acid , stearic acid impregnated in expanded graphite through vacuum impregnation followed by Vacuum Drying and Microwave acid treatment serves as novel shape stabilized phase change material of its type. The microwave acid treatment was done in order to increase the removal of moisture from the sample thus initiating proper bonding of its constituents. The mixture was produced in 1:1:1 ratio where all expanded graphite, lauric acid , stearic acid has one proportions of each other. The product obtained after microwave acid treatment was subjected to SEM, DSC analysis

The focus of this research is to improve the performance of dye-sensitized solar cells (DSSC) through the adoption of high-quality FTO thin films and incorporation of graphene with DSSC photoanode to enhance its electrical transport. In this research, nanostructured FTO films were first grown with homemade Streaming Process for Electroless and Electrochemical Deposition technology (SPEED) using Tin (II) chloride dihydrate and ammonium fluoride and other chemical formulations. The FTO structural property was measured by X-ray diffraction (XRD); the films’ optical property was determined with transmittance spectra to curve over the wavelength range of 200-1000 nm measured with a spectrophotometer while scanning electron microscope (SEM) was used to determine the morphological properties of the samples. The electrical transport was evaluated by Hall Effect measurements at room temperature with a four-point probe. The FTO samples with the best structural, optical and electrical properties were employed as electrodes and counter electrodes of DSSC along with titanium dioxide. Thus, effect of graphene on the efficiency of DSSC was investigated. It was shown that a graphene-based DSSC showed an efficiency of 7.98% which is slightly higher than that of DSSC prototype without graphene (6.02%). The higher efficiency obtained with graphene can be credited to the ultrahigh surface area and thermal conductivity of graphene which tend to enhance the charge mobility and photovoltaic performance of DSSC. More research is however required to determine the exact amount of graphene that could achieve optimal DSSC performance. Further studies will also offer an adequate clarification for starting point of the better incorporation of graphene in DSSCs.

In this paper, a method of charging lead acid battery with solar power by flyback converter is proposed. The basic system consists of a buffer circuit, auxiliary power circuit, control circuit, voltage feedback circuit and current feedback circuit. The system is capable of monitoring battery voltage and the current, charging the coupling inductor and automatic control of output duty cycle, overcharging and over-discharging protection. The experiment proves that the charging efficiency is improved by about 83% at full load.

This review paper explores the innovative realm of transparent solar panels, investigating their properties, applications, challenges, and recent advancements. Transparent solar panels, designed to harvest solar energy while allowing visible light to pass through, have gained significant attention due to their potential to revolutionize renewable energy technologies. The paper delves into the working mechanisms of various types of transparent solar panels, including Organic Photovoltaic (OPV) panels, Dye-Sensitized Solar Cells (DSSC), Perovskite Solar Cells, and Transparent Thin-Film Silicon Solar Cells. It discusses their integration into diverse applications, such as building-integrated photovoltaics, consumer electronics, the automotive industry, and aerospace. The review identifies challenges, including low efficiency, durability concerns, production costs, and integration hurdles, that currently hinder their widespread adoption. Moreover, the paper emphasizes the transformative potential of transparent solar panels in shaping the future of renewable energy, not only as energy generators but also as aesthetically pleasing and multifunctional components of our built environment. Finally, the paper underscores the need for continued research and development efforts to enhance efficiency, improve stability, and address integration challenges, paving the way for transparent solar panels to play a central role in the transition toward a more sustainable and energy-efficient future.

The shape memory alloys belong to the smart materials thanks to their thermomechanical proprieties' reply to thermal or to mechanical loading. These materials can change shape, stiffness, displacement, natural frequency, and many mechanical characteristics in response to stress or to heat such as conduction, convection or radiation. However, heating by convection or conduction are the most useful and studied methods unlike radiation. Therefore, this paper aims to study the radiation effect on the shape memory alloy behavior

The perovskite solar cells (PSCs) have been significantly improved by utilizing inorganic hole transporting layer (HTL), such as nickel oxide. Despite the promising properties, there are still limitations due to defects. Recently, research on self-assembled monolayers (SAM) is being actively conducted, which show promise in reducing defects and enhancing device performance. In this study, we successfully engineered a p-i-n perovskite solar cell structure utilizing HC-A1 and HC-A4 molecules. These SAM molecules were found to enhance the grain morphology and uniformity of the perovskite film, which are critical factors in determining optical properties and device performance. Notably, HC-A4 demonstrated superior performance due to its distinct hydrophilic properties with a contact angle of 50.3°, attributable to its unique functional groups. Overall, the HC-A4 applied film exhibited efficient carrier extraction properties, attaining a carrier lifetime of 117.33 ns. Furthermore, HC-A4 contributed the superior device performance with its favorable band alignment, achieving the highest device efficiency of 20%.

This review proposes an overview on the use of organic functionalized carbon nanostructures (CNSs) into solar energy conversion schemes. Our attention has focused in particular on the contribution given by organic chemistry to the development of new hybrid materials that find application in dye sensitized solar cells (DSSC), organic photovoltaics (OPV), perovskite solar cells (PSC) and also in photocatalytic fuel production, focusing in particular on the most recent literature. The request for new materials able to accompany the green energy transition that are abundant, low cost, with low toxicity, from renewable sources has further increased the interest in CNSs that meet all these requirements. The inclusion of an organic molecule, thanks to both covalent and non-covalent interactions, into a CNS, leads to the development of a completely new hybrid material able of combining and improving the properties of both starting materials. Besides the numerical data, which unequivocally state the positive effect of the new hybrid material, we hope that these examples can be inspiring for further research in the field of photoactive materials from an organic point of view.

Arctic ozone amount in winter to spring shows large year-to-year variation. This study investigates Arctic spring ozone in relation to the phase of quasi-biennial oscillation (QBO)/the 11-year solar cycle, using satellite observations, reanalysis data, and outputs of a chemistry climate model (CCM) during the period of 1979–2011. For this duration, we found that the composite mean of the Northern Hemisphere high-latitude total ozone in the QBO-westerly (QBO-W)/solar minimum (Smin) phase is slightly smaller than those averaged for the QBO-W/Smax and QBO-E/Smax years in March. An analysis of a passive ozone tracer in the CCM simulation indicates that this negative anomaly is primarily caused by transport. The negative anomaly is consistent with a weakening of the residual mean downward motion in the polar lower stratosphere. The contribution of chemical processes estimated using the column amount difference between ozone and the passive ozone tracer is between 10–20% of the total anomaly in March. The lower ozone levels in the Arctic spring during the QBO-W/Smin years are associated with a stronger Arctic polar vortex from late winter to early spring, which is linked to the reduced occurrence of sudden stratospheric warming in the winter during the QBO-W/Smin years.

Multilayer absorbers based on Cr2O3 and Cr, designed to improve the Solar-to-thermal conversion efficiency at mid temperatures in high vacuum flat thermal panel, are fabricated via sputtering deposition on bulk copper substrates and characterized by thermal and optical analysis. The refractive index of the single layers has been measured and used to estimate absorber thermal efficiency at the operating temperatures. Multilayers have been produced via sputtering deposition on bulk copper substrates. The absorber multilayers can be 10% more efficient than the commercial alternative at 250 °C operating temperatures, reaching 380 °C stagnation temperature without Sun concentration. The thermal stability has been checked at temperature of 400 °C in vacuum for four hours. High vacuum flat thermal collectors, equipped with the produced selective solar absorbers can obtain unprecedented performances and can give important contribution to the energy transition from fossil fuels to renewable energy for efficient heat production.

Solar flares are characterized by sudden bursts of electromagnetic radiation from the Sun’s surface, and caused by the changes in magnetic field states in solar active regions. Earth and its surrounding space environment can suffer from various negative impacts caused by solar flares ranging from electronic communication disruption to radiation exposure-based health risks to the astronauts. In this paper, we address the solar flare prediction problem from magnetic field parameter-based multivariate time series (MVTS) data using multiple state-of-the-art machine learning classifiers that include MINImally RandOm Convolutional KErnel Transform (MINIROCKET), Support Vector Machine (SVM), Canonical Interval Forest (CIF), Multiple Representations SEQuence Learner (Mr-SEQL), and Long Short-Term Memory (LSTM)-based deep learning model. Our experiment is conducted on the on the Space Weather ANalytics for Solar Flares (SWAN-SF) benchmark data set, which is a partitioned collection of MVTS data of active region magnetic field parameters spanning over 9 years of operation of the Solar Dynamics Observatory (SDO). The MVTS instances of the SWAN-SF dataset are labeled by GOES X-ray flux-based flare class labels, and attributed to extreme class imbalance because of the rarity of the major flaring events (e.g., X and M). As a performance validation metric in this class-imbalanced dataset, we used the true skill statistic (TSS) score. Finally, we demonstrate the advantages of the MVTS learning algorithm MINIROCKET, which outperformed the aforementioned classifiers without the need for essential data preprocessing steps such as normalization, statistical summarization, and class imbalance handling heuristics.

Solar energy adoption worldwide has expanded exponentially due to a surge in international interest in producing clean energy and the declining cost of solar power plants and their technology. It is anticipated that by 2050, solar will have surpassed fossil fuels to become the primary source of energy. However, one of the main challenges associated with solar energy production is the instability of photovoltaic (PV) power generation because of weather changes. Short-term forecasting of the power output of photovoltaic systems is essential for efficient management of the power grid and energy markets. This paper aims to evaluate the ability of deep learning (DL) models to provide accurate forecasting of hourly global horizontal irradiance (GHI) using different sets of features, including weather and aerosol variables along with solar radiation components. The results show that the best forecast skills are achieved by the long short-term memory autoencoder (LSTM-AE) model.

A widely used material for the photovoltaic (PV) arrays is crystalline silicon. The PV conversion losses of a power plant as a yearly average, include: light reflection losses (3,1%), low radiation and shadowing losses (3,2%), DC board losses (1,2%), DC/AC conversion losses (4%), mismatching losses (5,7%), temperature losses (7,6%), it can be stated that the major fraction of losses is related to the temperature increase of the sili-con solar cells. In real operating conditions, solar cells and modules operate at different temperatures, either due to changes in ambient temperature (atmospheric conditions changing with the seasons) and cooling rate, depending on wind speed and insolation, rain, snow, etc., or due to changes in the amount of heat (electrical power lost on the internal resistance of the cell), emitted during their operation. The possibility of operation of these devices in ground applications in the temperature range from -20 to +70C should be taken into account. The given range, of course, does not apply to work in the tropics. The detailed studies of the temperature on the electrical parameters of crystalline silicon solar cells have been presented. The theoretical justification of the temperature influence mechanism on the exploitation parameters of the silicon solar cells was submitted. Photovoltaic cells and modules are of better quality, the lower the value of temperature coefficients, in particular, attention should be paid to the decrease in maximum power with increasing temperature.The experimental results were compared with the theoretical predictions and the results, obtained by other authors and producers.

Currently, the Israeli energy industry faces the challenge of a considerable increase in solar electricity production. Being a relatively isolated system, the significant expansion of solar electricity may cause problems with electricity quality. The electrical storage installation can resolve this problem. In Israel's situation, the optimal solution can be the creation of a channel between the Mediterranean and the Dead Sea. The channel can solve three closely related problems: the increased production of desalinated water for domestic, industrial, and agricultural needs; the prevention of a permanent Dead Sea level decline and its imminent disappearance; the development of hydro-pumping electrical storage stations; and the creation of numerous PV facilities in the Negev area for national electricity generation. However, a detailed analysis should be done for the estimation of the possible increase of solar electric generation with the consideration of a stochastic PV outcome and a potential ability to use the Dead Sea for the brine discharge from electrical hydro-storage plants.

The current revolution in communication and information technology is facilitating the Internet of Things (IoT) infrastructure. Wireless Sensor Networks (WSN) are a broad category of IoT applications. However, power management in WSN poses a significant challenge when the WSN is required to operate for a long duration without the presence of a consistent power source. In this paper, we develop a batteryless, ultra-low-power Wireless Sensor Transmission Unit (WSTx) depending on the solar-energy harvester and LoRa technology. We investigate the feasibility of harvesting ambient indoor light using polycrystalline photovoltaic (PV) cells with a maximum power of 1.4mW. The study provides comprehensive power management design details and a description of the anticipated challenges. The power consumption of the developed WSTx was 21.09µW during the sleep mode and 11.1mW during the operation mode. The harvesting system can harvest energy up to 1.2mW per second, where the harvested energy can power the WSTx for six hours with a maximum power efficiency of 85.714%.

The organic solar cells (OSCs) have drawn attention in the past decade due to its cynosure in industrial manufacturing because of its promising properties such as low weight, highly flexible and low cost production. However, low η restricts the utilization of OSCs for potential application such as low cost energy harvesting devices. In this paper, OSCs structure based on triple junction tandem scheme is reported with three different absorber materials with the objective to enhance the absorption of photons which in turn improves the η, as well as its correlating performance parameters. The investigated structure gives the higher value of η = 14.33% with Jsc=16.87 (mA/m2), Voc=1.0 (V), and FF=84.97% by utilizing a stack of three different absorber layers with different band energies. The proposed structure is tested under 1.5 (AM) with 1 sun (W/m2). The impact of top, middle and bottom sub cells thickness on η is analyzed with a terse to find the optimum thickness for three sub cells to extract high η. The optimized structure is then tested with different electrode combination and the highest η is recorded with FTO/Ag. Moreover, the influence of upsurge temperature is also demonstrated on the proposed structure and observed that the upsurge temperature has greatly affected the electrical parameters of the device and η decreases from 14.33% to 11.40% when the temperature of the device rises from 300-400 K.

Due to the high solar irradiance or energy price, certain regions in the U.S. may reach 100% PV penetration and experience degradation of frequency response greater than the interconnection as a whole. Therefore, in this section, the 100% PV penetration region in each interconnection is simulated to study the local high PV penetration effects. The study was performed by quantifying RoCoF, frequency nadir, and settling frequency at different regional PV penetration levels. The impact of high regional PV penetration on the compliance of grid code on frequency response is also studied.

The question of building sustainable in a geographical locality is inexorably linked to cost. In 2011, one of the authors built a sustainable house that was (at the time) the highest certified sustainable home based on the National Association of Home Builder’s standards for sustainable construction. This Texas house has been used for residential and research purposes for the past decade. In this case study, the authors evaluate components of the construction and their effectiveness as well as unseen secondary and tertiary effects. Some of the specific components discussed are home site placement; rainwater harvesting (100% of residential requirements); aerobic septic system; grid-tied solar array power; electric car charging; geothermal heating and cooling; reclaimed wood framing; spray foam installation; selection of windows, fixtures, and appliances; on-demand electric water heaters for guest areas; generator backups; and use of local items. Electric bills and water system improvements are discussed in detail, as improvements were made as part of residential and research requirements. This case study suggests that the financial outlay is worth the extra up-front costs if residents in this geographical area and climate will occupy the residence 7 years.

We report on the study of energy-harvesting performance in medium-size (400 cm²) glass-based semitransparent solar concentrators employing edge-mounted photovoltaic modules. Systems using several different types of glazing system architecture and containing embedded diffractive structures are prepared and characterized. The technological approaches to the rapid manufacture of large-area diffractive elements suitable for use in solar window-type concentrators are described. These elements enable the internal deflection and partial trapping of light inside glass-based concentrator windows. We focus on uncovering the potential of pattern-transfer polymer-based soft lithography for enabling both the improved photon collection probability at solar cell surfaces, and the up-scaling of semitransparent solar window dimensions. Results of photovoltaic characterization of several solar concentrators employing different internal glazing-system structure and diffractive elements produced using different technologies are reported and discussed.

Limonene epoxide (1,2 limonene oxide) readily reacts with carbon dioxide in a ring opening copolymerization reaction with insertion of CO₂ and formation of polycarbonates of exceptional chemical and physical properties. Both poly(limonene carbonate) and poly(limonene dicarbonate) can be synthesized using low cost Zn or Al homogeneous catalysts. This study addresses selected relevant questions concerning the technical and economic feasibility of limonene and carbon dioxide polymers en route to the bioeconomy.

In this study, the efficiencies of flat-plate and U-tube solar collectors were investigated experimentally when an Al₂O₃ nanofluid was used as a working fluid and compared to those of solar collectors using water. The energy saving and CO₂ and SO₂ generated were calculated and compared to those of solar collectors using water. In addition, based on the experimental results, an economic analysis of the use of solar collectors in various countries was performed. As the concentration of the Al₂O₃ nanofluid increased, the performance of the solar collector improved. The highest efficiency for the solar collectors was shown at the concentration of 1.0 vol% with the nanoparticle size of 20 nm. The maximum efficiencies of the flat-plate and U-tube solar collectors using 1.0 vol%-Al₂O₃ nanofluid with 20-nm nanoparticles was 74.9% and 72.4%, respectively, when the heat loss parameter was zero. The efficiencies of the flat-plate and U-tube solar collectors using Al₂O₃ nanofluid were 14.8% and 10.7 higher, respectively, than those using water. When 50 EA flat-plate solar collectors were operated for one year using Al₂O₃ nanofluid, the coal use, generated CO₂, and generated SO₂ were 189.99 kg, 556.69 kg, and 2.03 kg less than those of solar collectors using water, respectively. In addition, the largest electricity cost reduction was in Germany.

Solar and wind resources available for power generation are subject to variability due to meteorological factors. Here, we use a new global climate reanalysis product, Version 2 of the NASA Modern-Era Retrospective Analysis for Research and Applications (MERRA-2), to quantify interannual variability of monthly-mean solar and wind resource from 1980 to 2016 at a resolution of about 0.5 degrees. We find an average coefficient of variation (CV) of 11% for monthly-mean solar radiation and 8% for windspeed. Mean CVs were about 25% greater over ocean than over land, and, for land areas, were greatest at high latitude. The correlation between solar and wind anomalies was near zero in the global mean, but markedly positive or negative in some regions. Both wind and solar variability were correlated with values of climate modes such as the Southern Oscillation Index and Arctic Oscillation, with correlations in the Northern Hemisphere generally stronger during winter. We conclude that reanalysis solar and wind fields could be helpful in assessing variability in power generation due to interannual fluctuations in the wind and solar resource. Skillful prediction of these fluctuations seems to be possible, particularly for certain regions and seasons, given persistence or predictability of climate modes with which these fluctuations are associated.

Glacial meltwater has been lifeline of agriculture in Gilgit-Baltistan for centuries which is being effected by the climatic changes and associated challenges. The government line institutions and development agencies have been investing to sustain and further extend the cultivated areas by leveraging the available glacial meltwater source. However, approximately 13% arable land, laying mainly along river banks, has limited access to glacial meltwater. Moreover, already cultivated areas also need alternate and sustainable irrigation water supplies to insurefood security. Hence, there is need to explore more potential options to address these challenges and bringing arable land under irrigation for regional prosperity and environmental gains. The International Centre for Integrated Mountain Development (ICIMOD) and its partners piloted solutions for aforementioned issues in Gojal, District Hunza. These solutions included river water lifting through solar and Hydraulic Ram Pumps, uphill water storages and application through drip irrigation systems. In order to assess the technical and economical viabilities of these piloted systems, a semi-structured questionnaire survey, field observation visits to collect data and economic assessment studies were carried out in Morkhun and Khyber. Both piloted systems have been proven as climate resilient, adaptable, environment friendly and economically viable. The cost to benefit ratio for solar powered drip irrigation and Hydraulic Ram Pump drip irrigation systems are 2.96 and 4.21 respectively, with payback period of 9.21 and 8.25 years respectively. The drip irrigation systems at Khyber and Morkhun sites have exhibited excellent hydraulic performance with Coefficient of Uniformity 92.61 and 93 % respectively. However, the field application efficiency of drip irrigation systems estimated for Khyber and Morkhun sites are 85.24 and 88.88% which are lower than the optimal value mainly due to lesser water holding capacity. The Hydraulic Ram Pump can lift four times more water to greater height, while comparing to solar pump of approximately similar capacity and higher capital costs. Both water lifting systems have some limitations and requires local customization for sustainable use.

Tomatoes, one of the most appreciated vegetables consumed, are crops well adapted for cultivation in arid and semi-arid conditions, the success of large yields is guaranteed by covering water consumption through irrigation. Solar Pumps - SP are driven by Photovoltaic Panels - PV (SPAPV), eliminating the dependence on electricity or diesel; they are environmentally friendly because they generate carbon-free electricity and the cost of operation and maintenance is lower. In order to preserve the water administered by drip to the tomato crop grown in solariums, mulching is used. In Husasău de Tinca, in the Crișurilor Plain, cultivation of tomato varieties without mulching (WM) and with mulching with black foil (MBF) were studied. To answer the question "How effective are water conservation measures in terms of energy independence?", two variants of SPAPVs, direct pumping (ADP) and storage tank (AST) were simulated. Considering the conditions in the solariums, tomato crops do not benefit from the contribution of precipitation, therefore it is proposed to determine the water consumption of tomatoes (ETRo), using the temperatures inside the solarium. In 2016, the average temperatures during the vegetation period were observed with an insurance of over 20 %, the irrigation norms were 6945.7 m3 ha-1, for the WM variant and 6594.0 m3 ha-1 for the MBF variant, respectively. Specific Investment (SI) is 214,795 Euro ha-1 in case of ADP and respectively 202,990 Euro ha-1 in case of ATS. The payback period (IPT) is between 2.68 years and 2.53 years for the ADP variant and between 1.63 years and 1.54 years for the ATS variant, respectively. The indications for water use and irrigation water use show that in the MBF variant the water administered by localized irrigation is better utilized than in the WM variant. In the conditions of Crișurilor Plain, the best solution for the distribution of water in solariums, with the help of SPAPVs is the mulching system of tomatoes grown in solariums (MBF) and the arrangement of the drip irrigation system with a water storage tank (ATS).

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

The feasibility of replacing the toxic chlorobenzene antisolvent with the environmentally friendly anisole in the fabrication of planar triple cation perovskite solar cells was explored. The successful integration of anisole not only ensures comparable device performance but also contributes to the development of more sustainable and green fabrication processes for next-generation photovoltaic technologies. Nevertheless, to ensure the possibility to achieve well-functioning unencapsulated devices, at any time of the year, with changed temperature and relative humidity, several batches with different cesium concentration were realized. We found that 10% of CsI in the precursor solution makes devices with low hysteresis index and sustained performance stability over a 90-day period both with cholorobenzene and anisole antisolvent. However the use of anisole as a green antisolvent ensures enhanced performance.

We study strong optical coupling of metal nanoparticle arrays with dielectric substrates. Based on the Fermi Golden Rule, the particle-substrate coupling is derived in terms of the photon absorption probability assuming a local dipole field. An increase in photocurrent gain is achieved through the optical coupling. In addition, we describe light-induced, mesoscopic electron dynamics via the nonlocal hydrodynamic theory of charges. At small nanoparticle size (<20nm), the impact of this type of spatial dispersion becomes sizable. Both absorption and scattering cross section of the nanoparticle are significantly increased through the contribution of additional nonlocal modes. We observe a splitting of local optical modes spanning several tenths of nanometers. This is a signature of semi-classical, strong optical coupling via the dynamic Stark effect, known as Autler-Townes splitting. The photocurrent generated in this description is increased by up to 2%, which agrees better with recent experiments than compared to identical classical setups with up to 6%. Both, the expressions derived for the particle-substrate coupling and the additional hydrodynamic equation for electrons are integrated into COMSOL for our simulations.

Depending on human body conditions and environmental conditions, it is sometimes difficult to conduct subject experiments. In such cases, it is effective to use a thermal manikin. There are few studies that investigate the effect of the non-uniform and asymmetric outdoor thermal environment on the mean skin temperature. The purpose of this study is to clarify the influence of the non-uniform and asymmetric thermal radiation of short-wavelength solar radiation in an outdoor environment on the calculation of the mean skin temperature. The skin temperature of the front of the coronal surface, which was facing the sun and where the body received direct short-wavelength solar radiation, and the skin temperature of the rear of the coronal surface, which was in the shadow and did not receive direct short-wavelength solar radiation were respectively measured. The feet, upper arm, forearm, hand and lower leg, which are susceptible to short-wavelength solar radiation in a standing posture, had a noticeable difference in skin temperature between sites in the sun and in shade. The mean skin temperature of sites facing the sun was significantly higher than the mean skin temperature of those in the shade.

The coronavirus disease 2019 (COVID-19) pandemic is the defining global health and socioeconomic crisis of our time and represents the greatest challenge faced by the world since the end of the Second World War. The academic literature indicates that climatic features, specifically the temperature and absolute humidity, are very important factors affecting infectious pulmonary disease epidemics (e.g., SARS, MERS); however, the influence of climatic parameters on COVID-19 remains extremely controversial. The goal of this study is to quantify the existing relationship between several daily climate parameters (temperature, relative humidity, accumulated precipitation, solar radiation, wind direction and intensity, and evaporation), local morphological parameters, and new daily positive swabs for COVID-19, which represents the only parameter that can be statistically used to quantify the pandemic. The daily deaths parameter was not considered because it is not reliable due to frequent administrative errors. Daily data on meteorological conditions and new cases of COVID-19 were collected for the Lombardy area from March 1, 2020, to April 20, 2020. This region in Italy exhibited the largest number of official deaths in the world per million inhabitants, with a value of approximately 1700 per million on june 30, 2020. Moreover, the apparent lethality was approximately 17% in this area, mainly due to the considerable housing density and the extensive presence of industrial and craft areas. The Mann-Kendall test and multivariate statistical analysis showed that none of the considered climatic variables exhibited statistically significant relationships with the epidemiological evolution of COVID-19, at least in the spring months in temperate subcontinental climate areas, with the exception of solar radiation, which was directly related and showed an otherwise low explained variability of approximately 20%. Furthermore, the average temperatures of two highly representative meteorological stations of Molise and Lucania, the most weakly affected by the pandemic. The temperatures at these stations were approximately 1.5°C lower than that in the cities in Lombardy of Bergamo and Brescia, again confirming that a significant relationship between the increase in temperature and decrease in virology from COVID-19 was not evident, at least in the Italian peninsula.

Recently it was found from Cassini data that the mean recession speed of Titan from Saturn is v = 11.3 ± 2.0 cm/yr which corresponds to a tidal quality factor of Saturn Q ≈ 100 while the standard estimate yields Q ≥ 6 · 10⁴ . It was assumed that such a large speed v is due to a resonance locking mechanism of five inner mid-sized moons of Saturn. In this paper, we show that an essential part of v may come from a local Hubble expansion, where the Hubble-Lemaˆıtre constant H0 recalculated to the Saturn-Titan distance D is 8.15 cm/(yrD). Our hypothesis is based on many other observations showing a slight expansion of the Solar system and also of our Galaxy at a rate comparable with H0. We demonstrate that the large disproportion in estimating the Q factor can be just caused by the local expansion effect. [Accepted for publication in "Gravitation and Cosmology". The paper is to appear in Vol. 28, Issue 2 (2022) of the journal Gravitation and Cosmology.]

Access to reliable, clean, modern cooking enhances life chances. One option is photovoltaic cooking systems. Accurate solar data is needed to ascertain to what extent these can satisfy the needs of local people. This paper investigates how to choose the most accurate satellite derived solar irradiance database for use in Africa. This is necessary because there is a general shortage of ground measurements for Africa. The solar data is needed to model the output of solar cooking systems, for instance, a solar panel, battery and electric pressure cooker. Four easily accessible satellite databases are validated against ground measurements using a range of statistical tests. Results demonstrate the impact of the mathematical measure used and the phenomenon of balancing errors. Fitting of the satellite model to appropriate climate zone and/or nearby measurements improves accuracy, as does higher spatial and temporal resolution of input parameters. That said, all the four databases reviewed were found to be suitable for simulating PV yield in East Africa.

Stabilized un-doped Zinc Telluride (ZnTe) thin films were grown on glass substrates under vacuum using closed space sublimation (CSS) technique. A dilute copper nitrate solution (0.1/100 ml) was prepared for copper doping known as ion exchange process in the matrix of ZnTe thin film. The reproducible polycrystalline cubic structure of undoped and Cu doped ZnTe thin films with preferred orientation (111) was confirmed by X-rays diffraction (XRD) technique. Lattice parameter analyses verified the expansion of unit cell volume after incorporation of Cu species into ZnTe thin films samples. The micrographs of scanning electron microscopy (SEM) were used to measure the variation in crystal sizes of samples. The energy dispersive X-rays was used to validate the elemental composition of undoped and Cu-doped ZnTe thin films. The bandgap energy 2.24 eV of ZnTe thin film decreased after doping Cu to 2.20 eV may be due to the introduction of acceptors states near to valance band. Optical studies showed that refractive index was measured from 2.18 to 3.24 whereas thicknesses varied between 220 nm to 320 nm for un-doped and Cu doped ZnTe thin film respectively using Swanepoel model. The oxidation states of Zn⁺², Te⁺² and Cu⁺¹ through high resolution X-ray photoelectron spectroscopy (XPS) analyses was observed. The resistivity of thin films changed from ~10⁷ Ω-cm for undoped ZnTe to ~1 Ω-cm for Cu-doped ZnTe thin film, whereas p-type carrier concentration increased from to respectively. These results predicted that Cu-doped ZnTe thin film can be used as an ideal, efficient and stable intermediate layer between metallic and absorber back contact for the heterojunction thin film solar cell technology.

The global increase in population, the phenomenon of climate change, the issue of water pollution and contamination, and the inadequate management of water resources all exert heightened strain on freshwater reserves. The potential utilization of the interfacial solar steam generation (ISSG) system, which utilizes photothermal conversion to generate heat on material surfaces for wastewater purification and desalination purposes, has been successfully demonstrated. Textile materials based ISSG devices, including (woven, nonwoven and knitting) fabrics and electrospinning membranes, exhibit distinct properties such as rough surface texture, high porosity, significant surface area, exceptional flexibility, and robust mechanical strength. These characteristics, combined with their affordability, accessibility, and economic viability for widespread implementation, make them extremely attractive for applications in SSG. In this review, a comprehensive analysis of emerging concepts, advancements and applications of textile materials (woven, nonwoven, and knitting) fabrics and electro-spun membranes in the ISSG for wastewater purification and desalination is highlighted. We also emphasize significant obstacles and potential prospects in both theoretical investigations and real-world implementations, aiming to contribute to future advancements in the domain of textile based materials interfacial evaporation in wastewater purification and desalination. Furthermore, the drawbacks and the challenges of ISSG systems are also highlighted.

Solar cell layers technology has achieved global standing in the solar cell layers deposition process, and it covers the innovative methods and techniques in significant applications. Recent solar cell layers technology has an advanced interest in a refined approach to enhance performance and highlights the importance of recent proficient procedures for manufacturing. For example, the application is used to search for novel materials for solar cells' layers to clarify the current energy crisis. The technological process and various types of solar cells depend on climate change. Among them, layers of solar cells and silicon wafer solar cells are very encouraging. Solar cell layers technology has led to solar cells being a more reasonable active option in design and production. The productivities facilitated by new solar cells still need to be enhanced for the various processes involved in the additional enhancement from Copper Indium Gallium Selenide (CIGS) microfilms to solar cell crystal structure dye-sensitized solar cells. The hydrophobic coating works as an anti-dust coating, enhancing efficiency and decreasing the cost of cleaning solar cells. In Saudi Arabia Majmaah City, most solar projects are in dry regions, where the dusty weather reduces solar cell efficiency. Therefore, combining these two properties and applying an anti-reflective and superhydrophobic coating will increase solar cell efficiency by 20%. Solar cells' crystal structure results are substituted with layers or new materials to balance environmental impact and toxic nature.

In order to reach the theoretical efficiency limits of lead-based metal halide perovskite solar cells, the voltage should be enhanced because it suffers from nonradiative recombination. Perovskite materials contain intrinsic defects that can act as Shockley-Read-Hall recombination centers. Several experimental and computational studies have characterized such defect states within the band gap. We give a systematic overview of compositional engineering by distinguishing the different defect reducing mechanisms. Doping effects are divided into influences on: (1) Crystallization; (2) Lattice properties. Incorporation of dopant influences the lattice properties by: (a) Lattice strain relaxation; (b) Chemical bonding enhancement; (c) Band gap tuning. The intrinsic lattice strain in undoped perovskite was shown to induce vacancy formation. The incorporation of smaller ions, such as Cl, F and Cd, increases the energy for vacancy formation. Zn doping is reported to induce strain relaxation but also to enhance the chemical bonding. The combination of computational studies using (DFT) calculations quantifying and qualifying the defect reducing propensities of different dopants with experimental studies is essential for deeper understanding and unraveling insights, such as the dynamics of iodine vacancies and the photochemistry of the iodine interstitials, and can eventually lead to a more rational approach in the search for optimal photovoltaic materials.

The spectra and global distributions of the X-ray emissions generated by the solar wind charge-exchange (SWCX) process in the terrestrial magnetosheath are investigated based on a global hybrid model and a global geocoronal hydrogen model. The solar wind O6+ ions which are the primary charge state for oxygen ions in solar wind are considered. The line emissivity of the charge-exchange born O5+ ions are calculated by Spectral Analysis System for Astrophysical and Lab oratory (SASAL). It is found that the emission lines from the O5+ ranges from 105.607 to 118.291 eV with the strong line at 107.047 eV. We then simulated the magnetosheath X-ray emission intensity distributions with a virtual camera at two positions of north pole and dusk at six stages during the passing of a perpendicular interplanetary shock combined with a tangential discontinuity structure through the Earth’s magnetosphere. During this process, the X-ray emission intensity increases with time, and the maximum value is 27.11 keV cm-2 s-1 sr-1 on the dayside, which is 4.5 times that before the solar wind structure reaches the Earth. A clear shock structure can be seen in the magnetosheath and moves earthward. The maximum emission intensity seen at dusk is always higher than that seen at north pole.

This work deals with the performance evaluation of novel flat photovoltaic-thermal (PV-T) modules under vacuum. Through a 1D (dimensional) steady-state-energy-balance numerical model developed in MATLAB, two different layouts are studied: the first consisting of a photovoltaic (PV) cell installed just below the glass encapsulating the flat panel, and the second where the PV cell is placed on the selective solar absorber (SSA). In both cases the thermal and electrical efficiencies have been evaluated at different SSA operating temperatures, in the range of 323 K to 423 K. The analysis has been conducted at different energy bandgap (E_bg) of the PV cell and assuming a variable transmittance or emittance of the PV cell, depending on the design. The two systems efficiency comparison has been carried out at the same operating temperature. Overall, this work highlights the importance of high vacuum insulation, which guarantees the reduction of convective thermal losses, and shows that the maximum energy is produced for PV cells with E_bg ≈1.5-1.7 eV, depending on layout and operating temperature, by including the thermal output in the PV-T optimization. The energy and exergy efficiencies obtainable using the proposed PV-T systems are considerably improved compared to the results previously reported in the literature.

To enable net zero sustainable thermal building energy this study develops an open-source thermal house model to couple solar photovoltaic (PV) and heat pumps (HP) for grid-connected residential housing. The calculation of both space heating and cooling thermal loads and the selection of HP is accomplished with a validated Python model for air-source heat pumps. The capacity of PV required to supply the HPs is calculated using an System Advisor Model integrated Python model. Self-sufficiency and self-consumption of PV and the energy imported/exported to the grid for a case study are provided, which shows that simulations based on the monthly load profile have a significant reduction of 43% for energy sent to/from the grid compared to the detailed hourly simulation and an increase from 30% to 60% for self-consumption and self-sufficiency. These results show the importance of more granular modeling and also indicate mismatches of PV generation and HP load based on hourly simulation datasets. The back-calculation PV sizing algorithm combined with HP and thermal loads presented in this study exhibited robust performance. The results indicate this approach can be used to accelerate the solar electrification of heating and cooling to offset the use of fossil fuels in northern climates.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

Our analysis of previous studies shows that solar energy and wind can consume negligible amount of water to generate one megawatt of electricity.

Silver powder, as the primary component of solar silver paste, significantly influences various aspects of paste performance, including printing, sintering, and conductivity. Silver powders prepared using the liquid-phase reduction method exhibit different microstructures depending on whether the growth process is dominated by aggregation or crystalline growth. This study explores the impact of different silver powder microstructures on packing density and sintering activity. It is observed that polycrystalline aggregated silver powder possesses higher surface energy, lower packing density, and greater sintering activity. Investigation into the influence of different silver powders on the electrical conductivity, adhesion, and structural density of silver paste reveals that polycrystalline aggregated silver powder is more suitable for lower sintering temperature pastes, whereas crystalline growth-type silver powder is better suited for higher sintering temperature pastes, resulting in a denser sintered silver layer. Finally, an analysis of the impact of various silver powders on the aspect ratio and electrical performance of solar cell silver grid lines yields higher aspect ratios (0.40) and photoelectric conversion efficiency (19.26%).

Space exploration introduces astronauts to many challenges such as space radiation and microgravity. Researchers have investigated vitamin C as a potential radiation mitigator and antioxidants for sustaining astronaut health. Building on our own studies, which indicate vitamin C's life-saving radioprotective effects and its potential as a radiation mitigator, our research highlights its promise, even when administered 24 h post-exposure. This is particularly relevant in scenarios where astronauts may be exposed to sudden large solar particle events, potentially resulting in lethal doses of space radiation. The success of vegetable cultivation on the International Space Station using NASA's Veggie system offers fresh, vitamin C-rich food. While approved supplements address somatic function, further research is needed to optimize vitamin C's efficacy in humans and develop antioxidant cocktails for space missions. The variable vitamin C content in vegetables underscores the necessity for utilization of artificial intelligence (AI) to assist astronauts in selecting and cultivating vitamin C-rich vegetables that are best suited to combat high levels of space radiation and microgravity. Particularly, AI algorithms can be utilized in analyzing various factors such as nutritional content, growth patterns, and cultivation methods. In conclusion, vitamin C shows significant potential for mitigating space radiation, and ongoing research aims to enhance astronaut health through optimal dietary strategies.