To investigate the structural behavior of simply supported concrete beams with steel and polypropylene fiber under low velocity impact loading. In all twenty-four beams (150X200X1800 mm) with simply supported boundary condition were modeled and analyzed using ABAQUS software. Steel and polypropylene fibers of aspect ratio of 60 and 231 respectively are used. The total volumes of fibers are maintained at 1% by volume of specimen. A 100 kg hammer with tip diameter 16 mm (hemispherical contact area = 201 mm2) with four different velocities (3.13 m/s, 4.42 m/s, 5.43 m/s and 6.11 m/s) were used in the analysis. It is observed that with the addition of hybrid fibers the deflection in beams was reduced. The beams with 1% PP and 0% steel fiber shows the maximum deflection values due to low modulus of elasticity. Beams with 0.9% steel and 0.1% polypropylene fibers was less affected in terms of deflection as compared to all other beams, it is due to presence of high tensile strength fibers.

Urban floods are typical urban disasters that threaten the economy and development of cities. Sponge cities can improve the flood resistance ability and reduce the floods by setting low-impact development measures (LID). Evaluating the floods reduction benefits is the basic link in the construction of sponge cities. Therefore, it is of great significance to evaluate the benefits of sponge cities from the perspective of different rain patterns. In this study, we investigated the urban runoff of various rainfall patterns in Mianyang city using the Strom Water Management Model (SWMM). We employed 2–100-year return periods and three different temporal rainfall downscaling methods to evaluate rain patterns and simulate urban runoff in Mianyang, with and without the implementation of sponge city measures. After calibration, model performance was validated using multi-source data concerning flood peaks and inter-annual variations in flood magnitude. Notably, the effects of peak rainfall patterns on historical floods were generally greater than the effects of synthetic rainfalls generated by temporal downscaling. Compared to the rainfall patterns of historical flood events, the flood protection capacities of sponge cities tended to be overestimated when using the synthetic rainfall patterns generated by temporal downscaling. Overall, an earlier flood peak was associated with better flood sponge city protection capacity.

Air pollution has created a lot of problems in the developed and developing countries. To avoid or reduce these problems, constant monitoring of the air should be ensured. The conventional techniques is costly because it requires a lot of money and time consuming. Biomonitoring has been the alternative method. Moss, lichens and plants are biomonitors available to entrap air pollutants. The aim of this paper is to discuss one of the ways of monitoring air pollution – Moss bag technique. To do this, types, choice, preparation, handling of bags after preparation of moss were discussed. From the literatures consulted, it was discovered that there were differences in the techniques used by the researchers. In all, the use of mosses with emphasis on the employment of moss bag have proved to be a powerful tool in airborne particulate and toxic elements. To conclude, developing countries should focus more on this technique because it will reduce cost of air monitoring.

Amidst escalating environmental concerns, short natural fiber thermoplastic (SNFT) biocomposites have emerged as sustainable materials for the eco-friendly production of mechanical components. However, their limited durability has prompted research into the experimental evaluation of the deterioration of the mechanical characteristics of SNFT biocomposites, particularly under the influence of ultraviolet rays. However, conducting tests to evaluate the mechanical properties can be time-consuming and expensive. In this study, an artificial neural network (ANN) model was employed to predict the mechanical properties (tensile strength) and the impact performance (resistance and absorbed energy) of polypropylene reinforced with 30 wt.% short flax or wood pine fibers (referred to as PP30-F or PP30-P, respectively). Eight parameters were collected from experimental studies. The ANN input parameters comprised nondestructive test results, including mass, hardness, roughness, and natural frequencies, while the output parameters were the tensile strength, the maximum impact load and absorbed energy. The model was developed using the ANN toolbox in MATLAB. The linear coefficient of correlation and mean squared error were selected as the metrics for evaluating the performance function and accuracy of the ANN model. They calculate the relationship and the average squared difference between the predicted and actual values. The data analysis conducted by the models demonstrated exceptional predictive capability, achieving an accuracy rate exceeding 96%, which was deemed satisfactory. For both the PP30-F and PP30-P biocomposites, the ANN predictions deviated from the experimental data by 3, 5, and 6% about the impact load, absorbed energy, and tensile strength, respectively.

Structural vibration induced by dynamic load or natural vibration is a nonnegligible factor in failure analysis. Based on vibrating boundary condition, impact resistance of shape memory alloy reinforced composites is investigated. In this investigation, modified Hashin’s failure criterion, Brinson’s model and visco-hyperelastic model are implemented into the numerical model to charactering the mechanical behavior of glass fiber/epoxy resin laminates, SMAs and interphase, respectively. First, fixed boundary condition is maintained in simulation to verify the accuracy of material parameters and procedures by comparing with experimental data. Then, a series of vibrating boundaries with different frequencies and amplitudes are applied during the simulation process to reveals the effect on impact resistances. The statistics of absorbed energy and contact force indicate that impact resistance of the composite under high frequency and large amplitude is lower than that under low frequency and small amplitude, and summarized by a mathematical expression.

The existence of insecurity in a state necessitates immediate government attention and action as it poses a risk to human life and property and impedes socio-economic development. The study aims to evaluate insecurity and its impact on socio-economic development in Oyo state. It will also determine the major causes of insecurity problems and offer data that can help develop effective security strategies and policies. The study population consisted of residents who were randomly selected from the Ibarapa North Local Government Area of Oyo State, Nigeria. The descriptive survey method was adopted and analyzed with the Chi-square technique. According to this research, there is a negative correlation between insecurity and the state's socio-economic development. The study recommends good governance and inclusive government policies to curb insecurity and ensure the state's socio-economic development.

In the process of use and manufacture, carbon fiber foam sandwich structures were often damaged by low-energy impact, resulting in performance degradation. Therefore, it was necessary to study the damage caused by low-speed impact of composite sandwich structures. In this paper, based on Hashin failure criterion, an equivalent finite element model of carbon fiber foam sandwich panel under low velocity impact was established. The model was used to simulate the damage of foam sandwich panel with [±45°/±45°/ (core) /±45°/±45°] ply structure under the impact energy of 10.58J, 21.17J, 31.75J and 42.34J. The simulation results of impact damage depth were compared with the experimental results. The error was less than 10%, which proved the rationality of the impact equivalent model. The model was used to predict and analyze the damage of foam sandwich panels with [±45°/ (core) /±45°], [±45°/ (0°, 90°) / (core) /±45°] and [±45°/ (0°, 90°) (core) / (0°, 90°) /±45°] ply structures under 21.17J impact energy. By comparing and analyzing the damage situation, impact force response time and impact velocity response time, the low energy impact resistance was analyzed. The results showed that increasing the number of ply structure of [±45°] can reduce the impact damage degree and improve the bearing capacity of sandwich panels.

When bone substitutes materials are used, the increased risk of infection due to the none-autogenic graft is often discussed. The treatment of large bone defects in geriatric patients, often with osteoporotic bone, often presents major challenges to surgery. Bone substitutes materials are available indefinitely without the risk of additional surgery in each patient. Can bone substitutes materials be used without hesitation in the geriatric patient?Eighty-three patients suffered traumatic fractures of the distal radius, proximal humerus, and proximal tibia. The defect zones were filled with bone substitute material based on nanocrystalline hydroxyapatite (NHA) or calcium phosphate (CP). For comparison, a reference group without the void filling with a bone graft substitute (void defects, ED) was studied. All patients over the age of 64 years were retrospectively evaluated for complications and radiological outcomes. Results: 106 patients sustained traumatic fractures of the distal radius (68.9%), proximal humerus (5.7%), and proximal tibia (22.6%). No differences in infections were found when comparing the groups (p=1.0). retrospectively evaluated. The KEM group had a nonsignificantly lower rate of pseudarthrosis (p=0.09). A relative risk (RR) reduction of complications of 32.64% was observed when bone grafting material was used. The NNT for the prevention of complications was 5.99. When bone healing was assessed by radiological images, some follow-up studies showed significant differences in fracture bridging (p<0.001).Conclusions: In contrast to previous studies, bone substitutes materials can support the healing process in geriatric patients without relevant disadvantages. With an NNT of 6 regarding complications, many patients could benefit from bone graft augmentation. No increased infection rate was observed.

When bone substitutes materials are used, the increased risk of infection due to the none-autogenic graft is often discussed. The treatment of large bone defects in geriatric patients, often with osteoporotic bone, often presents major challenges to surgery. Bone substitutes materials are available indefinitely without the risk of additional surgery in each patient. Can bone substitutes materials be used without hesitation in the geriatric patient? Eighty-three patients suffered traumatic fractures of the distal radius, proximal humerus, and proximal tibia. The defect zones were filled with bone substitute material based on nanocrystalline hydroxyapatite (NHA) or calcium phosphate (CP). For comparison, a reference group without the void filling with a bone graft substitute (void defects, ED) was studied. All patients over the age of 64 years were retrospectively evaluated for complications and radiological outcomes. Results: 106 patients sustained traumatic fractures of the distal radius (68.9%), proximal humerus (5.7%), and proximal tibia (22.6%). No differences in infections were found when comparing the groups (p=1.0). retrospectively evaluated. The KEM group had a nonsignificantly lower rate of pseudarthrosis (p=0.09). A relative risk (RR) reduction of complications of 32.64% was observed when bone grafting material was used. The NNT for the prevention of complications was 5.99. When bone healing was assessed by radiological images, some follow-up studies showed significant differences in fracture bridging (p<0.001). Conclusions: In contrast to previous studies, bone substitutes materials can support the healing process in geriatric patients without relevant disadvantages. With an NNT of 6 regarding complications, many patients could benefit from bone graft augmentation. No increased infection rate was observed.

This mixed-methods research article explores the influence of ChatGPT, a state-of-the-art AI language model, on the development of maladaptive learning habits in users. The study combines quantitative and qualitative data to provide a comprehensive understanding of how engaging with ChatGPT may inadvertently foster detrimental learning behaviors. Findings suggest that while ChatGPT can be a valuable learning tool, it has the potential to exacerbate or create bad learning habits if not used mindfully.

Most of the fishing currently practiced in Japan is done by small vessels with a small number of fishermen (one or two). One of the most common fishing methods is longline fishing. However, this method requires the vessel to operate at a constant low speed because the depth of the hook must be kept constant while adjusting the speed of the fishing boat to the tidal current. In addition, because the vessel must maneuver and fish at the same time, automation is desired. Thus, we propose a robotic system that can control the depth of the trap at a constant depth even when the speed of the vessel and the current change, and that can successfully fish without the need for skilled fishermen. Fishing can be conducted regardless of the speed of the vessel, whereas currently it is controlled by the speed of the vessel and the tidal current. Therefore, it may contribute to proposing new fishing methods as well as the existing ones. This can contribute to the shortage of successors to the fishing industry and to the revitalization of the fishing industry.

This article introduces the design and analysis of a slope detection circuit tailored for on-chip sensing of the load current in DC-DC converters. The novel indirect sensing approach is grounded in measuring the output voltage slope across the filtering capacitor during discharge phases. Consequently, this slope data can be effectively harnessed to control the converter switches. The slope detector circuit was designed in standard 65 nm CMOS technology using the nominal supply voltage of 1.2 V and can be used for current sensing within the range from one to hundreds of mA. Since the proposed circuit has mainly digital character, the robustness to process, temperature and supply voltage variations can be ensured rather conveniently.

Cultural routes are a composite set of heritage, referring to any ancient routes of human communication. As one of the key products of cultural tourism, they providing visitors with a rich cultural experience across regions. We systematically review reports and studies related to the tourism development of 38 cultural routes cases around the world, with a special focus on their distribution, typology, planning patterns and tools for cultural tourism. We summarized eight tools, there are some differences in how often these eight tools are used by the different types of routes and different planning patterns for routes tourism. The study also made an evaluation system based on the conservation principles of cultural routes to find out how different tools of tourism affect the conservation and development of the historical region. It was found that although many efforts have been made by tourism decision-makers to protect and develop cultural routes there are still many problems and challenges in the process of tourism development along cultural routes. We close the paper by making a few recommendations for decision makers and researchers concerning future routes’ tourism planning and study.

Mass mortality events and anthropogenic impacts were increasingly documented affecting Paramuricea clavata (Risso, 1826) during the last decades. These impacts enhance the settling of epibiontic organisms on the injured colonies. The epibiosis was studied by photographic sampling carried out on the granitic outcrops of the Tavolara Channel within the Tavolara-Punta Coda Cavallo Marine Protected Area (NE Sardinia) between 2017-2023 at 35-55 m. The number of colonies and percent surface involved in epibiosis, the specific richness of the epibiontic community and the temporal evolution of the phenomenon were investigated. Almost all the investigated gorgonians (93%) showed parts involved in epibiosis, with a high percentage of covering (one-third of the surface). Out of the 37 epibiontic species recorded, the most recurrent described an ecological succession dominated by hydrozoans, sponges, bryozoans, serpulids and the parasitic soft coral Alcyomiun coralloides. Nevertheless, single colonies studied through time revealed the unpredictability of the colonization process. The peculiar habitat of a high naturalistic value of the granitic outcrops hosting the P. clavata forests demonstrates a widespread suffering condition, supported both by environmental and anthropogenic sources of stress. Such considerations make it necessary to review the current zonation of the area, where the actual vulnerability and usability evaluations are based on obsolete information.

Low Emission Zone (LEZ) is an important mechanism to limit the negative environmental impact of traffic pollution in an urban area. Car traffic in the zone is strictly regulated to meet certain technical and environmental criteria. Such solutions of urban environment protection are gaining popularity, especially in European conurbations. Nowadays there are above 300 zones in Europe, mostly established in Italy and Germany. So far there are no LEZs in Eastern and Central European countries. However, the Warsaw authorities are just discussing launching of a LEZ in the city in 2024. According to the ongoing project, the zone is to be launched gradually, in five phases between 2024 and 2032, with the traffic criteria being tightened accordingly. The progressive emission reductions of the predominant pollutants in LEZ in consecutive phases were estimated on the basis of the Real Driving Emissions (RDE) test, carried out in 2020 by the ICCT. The gradually reduced emissions of NOx and PM were subsequently utilized as the input dataset for the regional CALPUFF model predictions, to calculate concentrations of these main traffic-induced pollutants within the LEZ area. The direct effect of the zone activation is reduction of air pollution in the urban center, which is mostly exposed to the pollution risk due to heavy traffic. Computer simulations reveal that implementation of the zone in the case of Warsaw will result in a quite significant reduction of NOx concentrations within the LEZ, such that its mean concentration in the zone becomes comparable to the rest of the conurbation. However, it will bring only a slight reduction of PM2.5 concentrations. This situation is due to the long-standing dominance of coal combustion in the Polish economy, which also applies to the urban municipal sector. As a consequence, particulate matter emissions of this sector are clearly predominant over the road traffic contribution. Balance can be achieved once the ongoing de-carbonization of the national economy has been completed.

Background: Simulations have historically aided training programs by providing a realistic and holistic replication of professional scenarios and procedures. Simulations have developed over the past 40 years to include varying fidelities and modalities of simulation. Learning in a simulation-centered environment has benefits, ranging from improved patient care to specific skills acquisition while catering to students’ numerous and varied learning approaches. Simulation is a multifaceted field that benefits all parties, the teachers, the learners, and the patients. The application of simulation to medical education and its amalgamation with other modes and substitutes allows for a more integrated learning and testing curriculum that advances the current trajectory of medical education. Such developments, however, are limited to resource rich areas, leaving behind low-middle income countries to use traditional, less evolved methodologies and practices. This review aimed to explore different aspects of simulation and focus specifically on low-cost task trainers and their accessibility. Method: The purpose of the study was to assess the accessibility of low-cost task trainers in terms of cost-effectiveness, distribution, validation, and frequency within specific specialties. To do so, 84 PubMed publications have been screened, and 39 filtered research studies have collected the necessary data. After analyzing the papers, we classified the following information – process, specialization, validation (y/n), costs, development location, and year of publication. Results: After carefully analyzing the accumulated data from the selected 39 publications, we found that most studies (i.e., 6 out of 39) were published in 2020. Emergency Medicine was the most common specialty for which low-cost trainers were developed (9 out of 39 procedural simulators); Otolaryngology followed this with 8 out of 39 trainers and general surgery with 7/39 of the task-trainers. The price ranges fluctuated and fell within the price bracket of USD 0 to USD 400 collectively. Our review also uncovered the concentration of development of such innovations solely in high income countries (HICs). Conclusion: Simulation is an invaluable tool applicable to a diverse range of phases of medical education. Future conjunction of simulation with low-cost substitutes along with increased encouragement and enthusiasm towards developing cost effective simulation-based learning environments (SBLEs) with the reserves and requirements of these areas in mind may prove to be a reliable option for low and middle resource settings

The development effect of water flooding in ultra-low permeability reservoir was poor due to its poor physical property and high shale content, the experimental study of air flooding which help to complement producing energy was carried out. Based on the Accelerating Rate Calorimeter experimental results, the crude oil of N block in L oilfield can produce low-temperature oxidation reaction, which was the basic condition of air flooding. Three groups of experiment natural cylinder core were designed for oil displacement, water flooding and air flooding were used respectively, and the relationship of differential pressure, oil recovery, injection capacity with injection volume was investigated. It has been showed on the result that the recovery efficiency improved sharply than water flooding, the effect of depressurization and augmented injection was obvious, and the air displacement was validation.

To mitigate the adverse impacts of urban stormwater on streams, watershed managers are increasingly using low impact development and green infrastructure (LID-GI) stormwater control measures such as rain gardens—vegetated depressional areas that collect and infiltrate runoff from rooftops and driveways. Their catchment-scale performance, however, can vary widely, and few studies have investigated the cumulative performance of residential rain gardens for event runoff control in intermediate-sized (i.e., 1-10 km2) suburban catchments. We modeled three years of continuous rainfall-runoff from a 3.1 km2 catchment in Columbia, MD, USA, using the Storm Water Management Model (SWMM). Various extents of rain garden implementation at residential houses were simulated (i.e., 25%, 50%, 75%, and 100% coverage) to determine the effects on peak flow, runoff volume, and lag time. On average, treating 100% of residential rooftops in the catchment reduced peak flows by 14.3%, reduced runoff volumes by 11.4%, and increased lag times by 3.2% for the 223 rainfall events during the simulation period. Peak flow reductions were greater for smaller storm events (p&lt;0.01). Our results show that residential rain gardens can significantly improve the runoff response of suburban catchments, and that they represent an effective and relatively low-cost option for urban watershed management and restoration.

This research aims to develop an inexpensive ocean observation instrument with a project name is NOBEL (Nusantara Oceanography Backdoor Experiment Laboratory)-BOX. The device can be installed on all types of vessels and placed in a specific area to map the water conditions, providing accurate data for managing a marine area specifically to water quality. The principle of NOBEL-BOX is to attach sensors in a container connected to a microcontroller and then measure directly. The method employed includes experimental design, laboratory and field tests, and data evaluation to produce the necessary system and instruments. The design process involves the construction of the instrument and the fabrication of the device. This process includes creating three-dimensional sketches/drawings, designing microcontrollers and data transmission systems, and power capacity. The sensors attached to this device are surface water temperature, air temperature, salinity, dissolved oxygen, pH, and TDS. The testing phase includes data validation, testing of the device in the laboratory, and field testing. The laboratory and field tests showed that the device worked and provided data that can be used to analyze the seawater condition spatially and over time.

The main aspects of material research: material synthesis, material structure, and material properties, are interrelated. Acquiring atomic structure information of electron beam sensitive materials by electron microscope, such as porous zeolites, organic-inorganic hybrid perovskites, metal-organic frameworks, is an important and challenging task. The difficulties in characterization of the structures will inevitably limit the optimization of their synthesis methods and further improve their performance. The emergence of integrated differential phase contrast scanning transmission electron microscopy (iDPC-STEM), a STEM characterization technique capable of obtaining images with high signal-to-noise ratio under lower doses, has made great breakthroughs in the atomic structure characterization of these materials. This article reviews the developments and applications of iDPC-STEM in electron beam sensitive materials, and provides an outlook on its capabilities and development.

Developing a low-cost wireless energy meter with power quality measurement for smart grid applications represents a significant advancement in efficient and accurate electrical energy monitoring.In increasingly complex and interconnected electrical systems, this device is essential in various applications, such as smart grids, enabling real-time energy usage monitoring. In such a context, smart meters expand the possibilities for sustainable and efficient energy use and promote better utilization of energy sources, especially non-renewable ones. According to the 2020 International Energy Agency (IEA) research, non-renewable energy sources represent 65% of the global total. The smart meter developed in this work is built based on the ESP32 microcontroller and easily accessible components, using a user-friendly development platform that offers a cost-effective solution while ensuring reliable performance. The main objective of the smart meter development was to enhance the software and simplify the hardware. Unlike traditional meters that perform electrical parameter calculations using complex hardware circuits, this project performed the calculations directly on the microcontroller. This approach reduced the complexity of the hardware, simplifying the meter’s design. With the high-performance processing capability of the microcontroller, efficient and accurate calculations of electrical parameters were achieved without the need for additional circuits. This software-driven approach with simplified hardware brought benefits such as reduced production costs, lower energy consumption, and increased meter development and updates flexibility. Furthermore, the integrated wireless connectivity in the microcontroller enables the transmission of collected data to remote monitoring systems for later analysis. The developed smart meter offers cost, energy efficiency, and flexibility benefits. It represents an innovative, efficient, and versatile solution for smart grid applications.

Stormwater management is a key urban issue in the world, in line with the global issues of urban sprawl and climate change. It is urgent to investigate the effectiveness in managing stormwater with different strategies for maintain urban resilience. A method based on a storm water management model (SWMM) was developed for assessing the control of stormwater runoff volume and the percentage removal of suspended solids by implementing a Sponge City strategy. An interdisciplinary approach was adopted incorporating Low Impact Development (LID) with urban Green Infrastructure and Gray Infrastructure paradigms in a typical old residential community in Suzhou, China. Four types of sponge facilities for reducing stormwater runoff were bio-retention cells, permeable pavements, grassed pitches, and stormwater gardens. The simulation results indicate that the stormwater pipe system can meet the management standard for storms with a five-year recurrence interval. The volume capture ratio of annual runoff is 91% and the reduction rate of suspended solids is 56%. This study demonstrates that Sponge City strategy is an effective approach for managing stormwater, particularly in old and densely populated urban areas. Implementing spongy facilities with a LID strategy for stormwater management can significantly enhance urban water resilience and increase ecosystem services.

The C/N ratio is an extremely important parameter in the composting process, which is directly responsible for the growth of microorganisms. A low C/N ratio contributes to higher emissions of greenhouse gases and odorous substances, such as ammonia (NH3), which is formed by nitrogen mineralization. Due to the highly toxic effects of ammonia, it is a particularly unwanted by-product that can disrupt the composting process because it poisons microorganisms and cause environmental issues. The activity of anammox bacteria, so far analyzed only in wastewater treatment processes, is a particularly efficient method of nitrogen removal, having an advantage over the conventional methods used previously. Our study proofs the presence of anammox bacteria during composting, what gives an opportunity to improve the process and reduce its impact on atmospheric pollution. Despite the aerobic nature of this process, the composted mass of waste presents conditions conducive to the development of these ammonia oxidizing bacteria, as well as other strains of microorganisms cooperating with them. This makes it possible to compost at a low C/N ratio; in addition, there is no need for additional energy supply through aeration, as the processes carried out by anammox bacteria do not require oxygen.

Low-frequency audible noise generated by the magnetostriction effect inherent to the operation of power transformers has become a major drawback, especially in cases where the electrical substation is located in urban areas subject to strict environmental regulations that imposes sound pressure limits, differing for day and night periods. Such regulations apply a +5 dB penalty if a tonal component of noise is present, which is clearly the case of magnetostriction noise, typically concentrated at twice the industrial frequency (50 Hz or 60 Hz, depending on the country). The strategy used to eliminate the tonal characteristics, therefore contributing to establish compliance with the applicable regulation and to alleviate the discomfort it causes to the human ear, consisted in superimposing to the substation noise a masking sound synthesized from “sounds of nature” with suitable intensities, to flatten the noise spectrum while enhancing the soundscape. The masking system (heavy-duty speakers powered by a microprocessor platform) was validated at an already judicialized urban scenario. Measurement results confirmed that the masking solution was capable of flattening the tonal frequencies, whose beneficial effect yielded the cancellation of the public civil action filed by the neighbors. The proposed solution is ready to be replicated to other scenarios.

The pursuit of more efficient transport has led engineers to develop a wide variety of 1 aircraft configurations with the aim of reducing fuel consumption and emissions. However, these 2 innovative designs introduce significant aeroelastic couplings that can potentially lead to structural 3 failure. Consequently, aeroelastic analysis and optimization has become an integral part of modern 4 aircraft design. In addition, aeroelastic testing of scale models is a critical phase in aircraft devel- 5 opment, requiring accurate prediction of aeroelastic behaviour during scale model construction to 6 reduce costs and mitigate risks associated with full-scale flight testing. Achieving a high degree of 7 similarity between the stiffness, mass distribution and flow field characteristics of scaled models 8 and their full-scale counterparts is of paramount importance. However, achieving similarity is 9 not always straightforward due to the variety of configurations of modern lightweight aircraft, as 10 identical geometry cannot always be directly scaled down. This configuration diversity has a direct 11 impact on the aeroelastic response, necessitating the use of computational aeroelasticity tools and 12 optimization algorithms. This paper presents the development of an aeroelastic scaling framework 13 using multidisciplinary optimization. Specifically, a parametric Finite Element Model (FEM) of the 14 wing is created, incorporating parameterisation of both thickness and geometry, primarily using 15 shell elements. Aerodynamic loads are calculated using the Doublet Lattice Method (DLM) em- 16 ploying twist and camber correction factors, and aeroelastic coupling is established using infinite 17 plate splines. The aeroelastic model is then integrated within an Ant Colony optimization (ACO) 18 algorithm to achieve static and dynamic similarity between the scaled model and the reference wing. 19 A notable contribution of this work is the incorporation of internal geometry parameterisation into 20 the framework, increasing its versatility and effectiveness.

Wheat gluten contains epitopes that trigger celiac disease (CD). A life-long strict gluten-free diet is the only treatment accepted for CD. However, very low-gluten wheat may provide an alternative treatment to CD. Conventional plant breeding methods are not sufficient to produce celiac-safe wheat. RNA interference technology, to some extent, succeeded in the development of safer wheat varieties. However, these varieties had multiple challenges in their implementation. Clustered Regularly Interspaced Short Palindromic Repeats-associated nuclease 9 (CRISPR/Cas9) is a versatile gene-editing tool that has the ability to edit the immunogenic gluten genes. So far, only a few studies have applied CRISPR/Cas9 to modify the wheat genome. In this article, we reviewed published literature that applied CRISPR/Cas9 in wheat genome editing to investigate the current status of the CRISPR/Cas9 system to produce a low-immunogenic wheat variety. We found that in recent years, the CRISPR/Cas9 system has been continuously improved to edit the complex hexaploid wheat genome. Although some reduced immunogenic wheat varieties have been reported, CRISPR/Cas9 has still not been fully explored in editing the wheat genome. We conclude that further studies are required to apply the CRISPR/Cas9 gene-editing system efficiently for the development of celiac-safe wheat variety and to establish it as a “tool to celiac safe wheat.”

This paper reports an experimental investigation on compression after low-velocity impact response for two lay-up configurations of symmetric CFRP laminated composite specimens obtained by reversing their angle-ply orientation, namely [0/-45/45/90]s versus [90/45/-45/0]s, the impact velocity of the projectile up to the BVID level being subsequently considered. To this aim, a modified Compression-After-Impact (CAI) test device is proposed that involves clamping the specimen's upper and lower edges between two adjustable wide and flat anti-buckling plates through a removable bolt-nut assembly. Such a solution relies on the fact that the specimen's active length is shortened, reducing the risk of global buckling. Besides, the bolts carry part of the load with minor localized bearing damage, provided that the metallic plates act as washers by supporting the bolt-bearing region laterally, thus avoiding crashing failures at the specimens’ loaded edges. With these settings, roughly the same percent decrease in the average values of maximum compression load (i.e., 22%) was recorded for both lay-up configurations impacted up to their BVID threshold, whereas in terms of compressive stiffness behavior, a reduction of 17 % was found for [0/-45/45/90]s specimens compared to 6 % obtained for [90/45/-45/0]s specimens.

In Data Science we are concerned with the integration of relevant sciences in observed and empirical contexts. This results in the unification of analytical methodologies, and of observed and empirical data contexts. Given the dynamic nature of convergence, described are the origins and many evolutions of the Data Science theme. The following are covered in this article: the rapidly growing post-graduate university course provisioning for Data Science; a preliminary study of employability requirements, and how past eminent work in the social sciences and other areas, certainly mathematics, can be of immediate and direct relevance and benefit for innovative methodology, and for facing and addressing the ethical aspect of Big Data analytics, relating to data aggregation and scale effects. Associated also with Data Science is how direct and indirect outcomes and consequences of Data Science include decision support and policy making, and both qualitative as well as quantitative outcomes. For such reasons, the importance is noted of how Data Science builds collaboratively on other domains, potentially with innovative methodologies and practice. Further sections point towards some of the most major current research issues.

Green infrastructure systems are often overdesigned. This may be a byproduct of static sizing (e.g., accounting for a design storm’s runoff volume but not exfiltration rates) or may be deliberate (e.g., buffering against performance loss through time). Regardless, overdesign may compromise plants’ access to water in systems where soil pits are embedded in infiltration beds. It could raise the storm size required for water to reach soil pits, reducing water availability between storms, which could ultimately induce plant physiological stress. This study investigated the hydrological dynamics and water relations of a tree trench system suspected to have been overbuilt and identified factors contributing to, compounding, and mitigating the risk of plant stress. Results provided strong evidence that the abovementioned processes played out. Water in the infiltration bed reached soil pits only once in three years, with that event occurring during a hydrant release. Moreover, minimal water was retained in the soil pit during the event due to the hydraulic properties of the soil media. Through a growing season, one of the two tree types frequently experienced water stress, while the other did so only rarely. These contrasting responses can likely be attributed to roots either being largely confined to the soil pits or reaching a deeper water source. Implications of these results for green infrastructure design are considered.

At least one ultrasound is recommended to predict fetal growth restriction and low birthweight earlier in pregnancy. However, in low-income countries imaging equipment and trained manpower are scarce. Hence, we developed and validated a model and risk score to predict low birthweight using maternal characteristics during pregnancy, for use in resource limited settings. We conducted a prospective cohort study among 379 pregnant women in South Ethiopia. A step-wise multivariable analysis was done to develop the prediction model. To improve clinical utility, we developed a simplified risk score to classify pregnant women at high- or low-risk of low birthweight. The accuracy of the model was evaluated using the area under the receiver operating characteristics curve (AUC) and calibration plot. We evaluated the clinical impact of the model using a decision curve analysis across various threshold probabilities. Age at pregnancy, underweight, anemia, height, gravidity, and presence of comorbidity remained in the final multivariable prediction model. The area under the receiver operating characteristics curve (AUC) of the model was 0.83 (95% confidence interval: 0.78 to 0.88). The decision curve analysis shows the model provides a higher net benefit across ranges of threshold probabilities. In general, this study showed the possibility of predicting low birthweight using maternal characteristics during pregnancy. The model could help to identify those at higher risk of having a low birthweight baby. This feasible prediction model would offer an opportunity to reduce obstetric-related complications and thus improving the overall maternal and child healthcare in low- and middle-income countries.

Community co-creation is increasingly crucial to the building of sustainable societies. Communities must proactively and independently create value chains in the face of many wicked problems. However, practical frameworks and tools for facilitating community co-creation require further development. As such, for this paper, we propose a theoretical framework for analyzing community co-creation value chain mechanisms based on a narrative review of literature on Collective Impact, social impact assessment, and Community Capital from the perspective of collective impact, a framework with a fair amount of previous research. We argue for the importance of applying knowledge of social impact assessment, particularly for the collective impact conditions of common agenda and shared measurement system. We discuss its relationship with the Theory of Change and the use of systems thinking to mitigate the subjectivity and arbitrariness of design thinking. Furthermore, we emphasize the value of employing the community capital concept as a framework for analyzing interrelationships among elements. By integrating multiple concepts, we enhance the collective impact framework and outline potential avenues for future research on analyzing and effectively implementing co-creation value chain mechanism in a community-based approach.

This paper provides an overview of current literature on community-led development initiatives in urban contexts, their role in addressing urban inequality, and the challenges they face. This study examines effective strategies of community-led initiatives, such as empowering communities, building partnerships, mobilizing resources, focusing on local needs, and participatory design methods. Case studies from around the world demonstrate how successful community-led development initiatives have been able to overcome obstacles to create more inclusive and equitable urban environments. Institutional support, including technical assistance, capacity building, and regulatory frameworks, are crucial for promoting the success and sustainability of these initiatives. Challenges to community-led initiatives include limited resources, capacity building needs, inadequate infrastructure, lack of institutional support, and lack of trust among community members. Therefore, the paper suggests that it is essential to address these challenges to enable the success of community-led development initiatives. Furthermore, this study recommends that future research should explore how emerging technologies and innovative approaches can effectively support community-led development initiatives and advance more just and sustainable urban development.

Developing new energy is critical to China's green and low-carbon development. And the New Energy Demonstration City Policy (NEDCP) is a vital innovation policy that inspires the development of new energy. Is the NEDCP facilitating green and low-carbon development, if so, how? Employing unbalanced panel data from 2003 to 2017, the impact of NEDCP on green and low-carbon development was studied by using the "difference in difference" (DID) model. We find that this policy can take significantly role. After various robustness tests, our results are still valid. According to the heterogeneity analysis, non-resource and non-old industrial base cities have a greater positive impact from this policy. The mechanism analysis denotes that the positive policy effect works through upgrading the industrial structure and stimulating urban innovation. The substantial empirical evidence presented in this article supports the continued promotion and implementation of new energy demonstration cities.

With technological transformations such as big data, blockchain, artificial intelligence, and cloud computing, digital techniques are penetrating the field of finance. Digital finance is a resource-saving and environmentally friendly innovative financial service. It shows great green attributes and can drive the flow of financial resources towards environmentally friendly enterprises, thereby promoting green and low-carbon development. This paper investigates the effects of digital finance on green and low-carbon cyclic development and the mechanism. First, the level of green and low carbon cyclic development in China is estimated from multiple aspects based on the panel data of 31 provinces by using the spatio-temporal range entropy weight method. Then, the working mechanism of digital finance on green and low carbon cyclic development is revealed by performing empirical tests based on panel regression models, mediating effect models, and threshold models. Finally, the effects of digital finance and conventional variables on green and low-carbon cyclic development are investigated by using a random forest model and a CatBoost model in based on the machine learning. The results show that digital finance has significant positive effects on green and low-carbon cyclic development, and technological innovation plays a key role in the effects of digital finance on green and low-carbon cyclic development; meanwhile, the driving effect of digital finance on green and low carbon cyclic development shows nonlinear features with increasing “marginal effect”; besides, both digital finance and conventional factors have significant impacts on green and low carbon cyclic development. This study provides an empirical basis and path reference for digital finance to achieve “carbon peak, carbon neutralization” in China.

Abstract: Mass spectrometry research laboratories reported multiple probes for ambient ionization in the last years. Combining them with a mechanical moving stage enables automated sampling and imaging applications. We developed a robotic platform, which is based on RepRap 3D-printer components, and therefore easy to reproduce and to adopt for custom prototypes. The minimal step width of the Open LabBot is 12.5 μm, and the sampling dimensions (x, y, z) are 18 × 15 × 20 cm. Adjustable rails in an aluminium frame construction facilitate the mounting of additional parts such as sensors, probes, or optical components. The Open LabBot uses industry-standard G-code for its control. The simple syntax facilitates the programming of the movement. We developed two programs: 1) LABI-Imaging, for direct control via a USB connection and the synchronization with MS data acquisition. 2) RmsiGUI, which integrates all steps of mass spectrometry imaging: The creation of G-code for robot control, the assembly of imzML files from raw data and the analysis of imzML files. We proved the functionality of the system by the automated sampling and classification of essential oils with a PlasmaChip probe. Further, we performed an ambient ionization mass spectrometry imaging (AIMSI) experiment of a lime slice with laser desorption low-temperature plasma (LD-LTP) ionization, demonstrating the integration of the complete workflow in RmsiGUI. The design of the Open LabBot and the software are released under open licenses to promote their use and adoption in the instrument developers’ community.

The A.C.Q.U.A. (Advisable Conscious Quality Use from Assisi) project, promoted by the Climate and Energy and Heritage Design courses of the Planet Life Design Master Program, addresses the theme of the recovery and regeneration of ancient wash-houses in the context of energy, environmental sustainability and innovation, a way of understanding cultural heritage in the wider sense of heritage community through the active participation of all the actors involved: universities, institutions, businesses, students and citizens. The proposal, tested in the municipalities of Assisi and Ruviano (ITALY), involves the creation of a "Community Wash House", a new way of carrying out the usual domestic act of washing clothes in the open air, next to the places where this rite was traditionally performed, in technologically innovative constructions that use renewable energy sources and encourage a reduction in household consumption of water and energy. This project is part of the training of professionals in the new inter-university course that combines knowledge of the tools of technical and scientific design with historical and cultural perspectives in a perspective of sustainable redevelopment of existing structures in the area and the use of alternative energy sources with low climate impact, calculated using the statistics of the Copernicus CDS.

As a rapidly growing coastal megacity, Shanghai is continuously threatened with land subsidence issues since 1920s. Land subsidence was controlled in 1960s, however in 1990s, unconscious and dangerous urban underground space (UUS) exploration and tunneling development are causing further land subsidence. It is imperative to study previous relations towards future adaptive and resilient scenario modelling and planning. There are multiple cause-effect factors determined in the urban built environment of Shanghai megacity. This paper presents the current evidence based on the relations of the multifactor of the spectrum. Methods consist of understanding the cause-effect relations and spatiotemporal from the crucial period of 1960-2020. Data are collected secondarily from multiple open sourced databases. The results determine Shanghai are highly influenced by the UUS development induced-subsidence, tunneling leakage and weak spatial modelling. Spatiotemporal pattern has shown a mixed positive-negative impact: population, land subsidence is growing in parallel distribution (positive) with tunneling leakage, construction of tunneling, metro system, UUS development, building price, reconstruction area, GDP growth, land price, arable land decrease and further tunnel settlement in Urban City Centre, Pudong New Area, Minhang, Baoshan and Songjiang districts. These results are useful for further adaptive and resilient scenario modelling and spatial planning.

Smart farm is a technology that greatly helps improve the productivity and quality of crops and is being actively introduced into indoor environments such as green houses. However, it has not yet been distributed to field-grown crops. The main reason is that, unlike indoor environments, it is very difficult to collect sensor data for monitoring the growth environment of crops in open fields where weather conditions change significantly and power supply is difficult. Additionally, because various sensors are used, the data formats of the devices are different, making it difficult to process. This paper presents a field crop growth environment monitoring and big data analysis system. The proposed system first solves power supply and data communication problems using solar power generation and LPWA technology. Additionally, based on the oneM2M architecture, data from various sensors is transmitted to the server using standardized technology. The transmitted data is stored and managed on the server as big data, and can be used to predict the production and quality of field-grown crops and take appropriate measures. The proposed system is expected to create an environment optimized for the growth of field crops and help prevent and manage diseases.

Osteoporotic spinal fractures represent an increasingly widespread health problem in our aging society. We aimed to investigate the treatment options for low-energy spinal fractures in the el-derly and their impact on mortality, focusing on surgical stabilization using minimally invasive and open techniques. We evaluated 1356 patients over 50 years of age with compression frac-tures sustained due to low energy trauma treated at a single trauma center. We compared the mortality of patients following stable and operated/non-operated unstable compression frac-tures and the eligibility to surgery using the open and minimally invasive approach. The pa-tients received surgical or conservative care according to severity and eligibility to surgery. The mortality hazard ratio of patients who underwent screw fixation was 1.02 (P > .91), of patients who refused surgery was 1.68 (P < .001) and that of patients with anesthesiological contraindica-tion was 1.57 (P = .08), compared to conservatively treated patients with stable fractures. The dif-ference in mortality between open and minimally invasive surgeries was not significant, but the number of patients eligible for surgery with the minimally invasive procedure was significantly higher (OR: 0.25; P < .001). Spinal stability after fractures may be an important predictor of sur-vival in patients with low-impact fractures.

This paper examines the Business Model (BM) from a socioeconomic system perspective to discern key factors, and understand its interactions resulting in the Scaling of Social Impact (SSI) in Social Entrepreneurship (SE). Previously, studies have explained the importance of BM in relation to SE. However, there is a lack of empirical studies on how BM’s transitions through participation of various actors result in SSI. This research applies qualitative analysis on a single case study of a Japanese social startup, “mymizu”, the first water refill application platform in Japan. The findings show that collaboration amongst different stakeholders on the initial phase of the BM could increase awareness of responsible consumption, convert into actual users for sustainability, and change their behavior. Secondly, members of the society could take on dual roles, both as users and collaborators in the BM, which results in an exponential scaling effect of the social impact. This paper contributes towards adding a participatory stakeholder (PS) to the ecosystem of SSI and building a “regenerative” BM that is relevant in SE towards sustainability.

Concurrent waves of Coronavirus disease, Ebola virus disease, avian influenza A and black fungus are jeopardizing the lives in some parts of Africa and Asia. From this point of view, this review aims to summarize both socio-economic and public health implications of these parallel outbreaks along with their best possible management approaches. Various online databases were used to collect the necessary information regarding these outbreaks. Based on the reports published and analyses done so far, the long-lasting damages caused by these simultaneous outbreaks on global socio-economical and public health status can be conceived from the past experiences of outbreaks, especially the COVID-19 pandemic. Moreover, prolonged restrictions by the local government may lead to food insecurity, global recession, and an enormous impact on the mental health of people of all ages, specifically in developing countries. Such overwhelming effects already have been reported to be declining national growth of the economy as well as increasing political insecurity and shortage of basic needs. Although various actions have already been taken including vaccination, clinical management, and further research, social distancing, and lockdown, etc. to improve the situation, the emerging variants and associated genetic mutations may make the containment difficult worsening the situation again. Considering the current mutational dynamics of the pathogens and the past experiences, perpetual preparedness along with updated clinical management backed by epidemiological studies and innovating scientific effort are inevitable to combat the simultaneous waves of multiple infectious diseases.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

NUSES is a planned space mission aiming to test innovative observational and technological approaches related to the study of low-energy cosmic rays, gamma rays and high-energy astrophysical neutrinos. Two scientific payloads will be hosted onboard the NUSES space mission: Terzina and Zirè. Terzina will be an optical telescope readout by SiPM arrays, for the detection and study of Cerenkov light emitted by Extensive Air Showers generated by high-energy cosmic rays and neutrinos in the atmosphere. Zirè will focus on the detection of protons and electrons up to a few hundred MeV and to 0.1-10 MeV photons and will include the Low Energy Module (LEM). The LEM will be a particle spectrometer devoted to the observation of fluxes of low-energy electrons in the 0.1-7 MeV range and protons in the 3-50 MeV range along the Low Earth Orbit (LEO) followed by the hosting platform. The detection of Particle Bursts (PBs) in this Physics channel of interest could give new insight into the understanding of complex phenomena such as eventual correlations between seismic events or volcanic activity with the collective motion of particles in the plasma populating van Allen belts. With its compact sizes and limited acceptance, the LEM will allow the exploration of hostile environments such as the South Atlantic Anomaly (SAA) and the inner van Allen belt, in which are expected electron fluxes of the order of 106−7 cm−2 sr−1 s−1. Concerning the vast literature of space-based particle spectrometers, the innovative aspect of the LEM resides in its compactness, within 10x10x10 cm3, and in its “active collimation” approach dealing with the problem of multiple scattering at these very low energies. In this work, the geometry of the detector, its detection concept, its operation modes and the hardware adopted will be presented. Some preliminary results from the Monte Carlo simulation (Geant4) will be shown.

The problem of normal impact of a rigid sphere onto a Maxwell viscoelastic solid half-space is considered. The first-order asymptotic solution is constructed in the framework of Hunter’s model of viscoelastic impact [Hunter, S. C., 1957. Energy absorbed by elastic waves during impact. Journal of the Mechanics and Physics of Solids, 5(3), 162–171.]. In particular, simple analytical approximations have been derived for the maximum contact force and the time to achieve it. A linear regression method is suggested for evaluating the instantaneous elastic modulus and the mean relaxation time from a set of experimental data collected for different impactors and impact velocities.

Floor mats are commonly used to improve the impact sound performance of existing homes, but the actual reduction does not consistently appear depending on the test-bed conditions used to determine it. Therefore, this study evaluated the effects of the environmental conditions of the test-bed on the impact sound reduction performance of different floor mats. The Korean Industrial Standard, KS F 2865, specifies the measurement method in the test room and sets the thickness range of the available target floor structure from bare slab 120 mm to 210 mm. The evaluation method is ∆?, which is the difference in standardized impact sound levels before and after the installation of the floor finishing material. In this study, a total of eight types of floor mats were tested in four different test-beds according to KS F 2865. The impact sources used were tapping, bang machines and a rubber ball to consider both light-weight and heavy-weight impact sounds. The results were derived as impact sound reduction performance for each frequency band and a single number quantity. The results showed that light impact sound had a similar minimum reduction characteristic of at least 38 dB, regardless of the floor structure on which the mat was installed. However, the heavy-weight impact sound showed different tendencies depending on the floor mat and the characteristics of the floor structure of the test-bed when a bang machine and a rubber ball were used. In particular, the reduction by the bang machine showed less than half the tendency of the reduction by the rubber ball, and the tendency of the heavy-weight impact sound to be reduced depending on the floor mat was maintained, but the reduction differed depending on the test bed. The reduction was larger in the box-type test room than in the real-life type test room, and among the box-type test rooms, the one with a thicker bare slab showed a relatively larger reduction. In addition, the reliability of the measurement results was discussed through the correlation analysis between the single number quantities depending on the thickness of the bare slab of the test-beds.

Considering that a fair coin has two sides and a cylindrical edge, the probability that it would fall on its edge is calculated, yielding the probability of heads or tails less than 50%. Theoretical models for a static case and for five dynamic cases, without and with rebounds, show that there is a small probability that the coin does not fall on its head or tail, depending on initial toss conditions, the coin geometry and conditions of the coin and landing surfaces. For the dynamic model with rebounds, it is found that the probability that a 50 Eurocent coin thrown from a normal height with common initial velocity conditions and appropriate surface conditions will end up on its edge is in the order of one against several thousand.

We have modelled the energy consumption of prototype and real buildings under present and future climatic conditions with the EnergyPlus model to develop a better understanding of the relationship between changing climate conditions and energy demand. We have produced detailed meteorological information with 50 meters of spatial resolution through dynamical downscaling process combining regional, urban and computational fluid dynamics models which include the effects of the buildings on urban wind patterns. The city of Madrid has been chosen for our experiment. The impact on energy demand and their respective economic cost are calculated for year 2100 versus 2011 based on two IPCC climate scenarios, RCP 4.5 (stabilization of emissions) and RCP 8.5 (not reduction of emissions). Findings show that climate change will have a significant impact on the energy demand for buildings. Space heating demand will be increased by the RCP 4.5 and cooling demand will be increased for the RCP 8.5 in the analysed buildings.

The advent of remote work has ushered in a new era of economic transformation, redefining the dynamics of local economies, and unleashing the multiplier effect on a national scale. This abstract explores the profound implications of remote work on local economies, dissecting how the multiplier effect operates within a nation's economic landscape. The multiplier effect is a fundamental economic concept that highlights how changes in spending and investment can create a ripple effect, leading to a magnified impact on an economy. This concept gains new significance in the context of remote work, as it triggers a chain reaction of economic activities that radiate from remote workers to their local communities. The increased flexibility and reduced geographical constraints of remote work have reshaped the allocation of resources. The continued reliance on remote work may lead to a reduction in demand for commercial real estate in urban centers, necessitating adaptive urban planning strategies. In conclusion, the rise of remote work has initiated a transformative era for local economies, driven by the multiplier effect. By amplifying the impacts of spending and investment, remote work fosters job diversification, innovation, and infrastructure development within communities. As remote work continues to reshape the landscape of work and life, understanding and harnessing its multiplier effect remains paramount for policymakers, businesses, and local communities alike. The multiplier effect is a concept in economics that illustrates how changes in spending can lead to larger impacts on a nation's economy through a chain reaction of economic activities. It demonstrates that an initial injection of spending, whether from government expenditure, investment, or consumption, doesn't just have a one-time impact. Instead, it sets off a series of interconnected spending and income-generation processes that result in a larger overall increase in economic activity. t's important to note that the multiplier effect can work in reverse as well. If there's a decrease in spending, it can lead to a decrease in economic activity and income through the same chain reaction process. This concept highlights the interconnected nature of economic activities and emphasizes the significance of changes in spending patterns on a nation's overall economic health. The magnitude of the multiplier effect is influenced by factors such as the marginal propensity to consume (the proportion of additional income that households spend), leakages (savings and taxes that reduce the multiplier effect), and the extent to which additional spending creates additional production capacity within the economy. Understanding the multiplier effect is essential for policymakers, as it helps them gauge the potential impacts of changes in fiscal and monetary policies on the economy.

Climate change represents a major threat to lotic freshwater ecosystems and their ability to support the provision of ecosystem services. England’s chalk streams are in a poor state of health, with significant concerns regarding their resilience, the ability to adapt, under a changing climate. This paper aims to quantify the effect of climate change on hydroecological response, the health of the river, for the River Nar, a SSSI in the south-east of England. To this end, we apply a coupled hydrological and hydroecological modelling framework, with the UKCP09 probabilistic climate projections serving as input (A1B high emissions scenario). Results show that, from 2021 to the end of the century, hydroecological response becomes more heterogeneous. Despite the limited range of the functional feeding groups on the baseline, the River Nar has been able to adapt to extreme events due to inter-annual variation. In the future, this variation is greatly reduced, raising real concerns over the resilience of the river ecosystem under climate change. These new insights into the health of the River Nar, and chalk streams more generally, highlights the necessity of further study and the real need to for changed river management practices.

An extended classification of active RC- and RLC- filters with Sallen-Key architectures, including those created in the last three years, is proposed. This makes it possible to formulate new design directions for an extended family of active RC- and RLC- Sallen-Key filters (PF, LPF, HPF, RF) for the tasks of high-speed and ultra-fast analog-to-digital signal conversion.

The German government's ambitious goal of achieving CO2-neutrality by 2045 has prompted a focus on improving building insulation as a vital step toward energy efficiency. However, in this process, existing radiators and boilers are often left unchanged, leading to inefficiencies due to oversized heating systems. This paper presents various approaches to reduce the required radiator inlet temperature, drawing on data from 100 multifamily buildings. The approaches include heat reserve reduction, heat power shifting, uniform radiator usage, and heat requirement analysis. These approaches collectively aim to lower flow temperatures and decrease peak heat loads, reducing energy consumption, and minimizing waste in compliance with the user comfort temperature. The findings reveal that the application of these methods can lead to substantial temperature reductions, with an average decrease of 20.82 K and 7.28 K for the highest necessary flow temperature in the provided example. Furthermore, peak load reductions of 21.07% and 13.65% were achieved, demonstrating the potential to enhance energy efficiency. While each approach can be applied individually, their synergistic implementation can highly increase the efficiency of water to x heat pumps, due to the lower required flow temperatures.

Construction Design Management (DM) involves the coordination of design process and activity to ensure quality project design, yet it involves many challenges. This work reports on a collaborative Knowledge Transfer Project (KTP) that tackled several challenges faced by construction design management practitioners. Employing a design science research methodology (DSRM), qualitative analysis of semi-structured interviews with purposively identified design managers first uncovered real world concerns around design coordination, and designer performance monitoring. Then to address these concerns, a web-based design management prototype dashboard was developed which uses typical project data to aid the management of design coordination activity and facilitate design management task prioritization and reporting functionalities. By digitalizing selected design management processes to improve efficiency, and productivity, the visual reporting capability of the dashboard enables design production to be monitored at project and portfolio levels; trends in designer performance to be assessed and focus to be retained on technical queries (TQs) and requests for information (RFIs). By reporting on the development of this web-based Design Management prototype dashboard and illustrating how it can enhance design management productivity in construction firms, this work also provides further evidence of how employing a design science research methodology in construction can produce practical solutions that address real world construction concerns.

Climate change is increasing air temperatures and altering the precipitation and hydrological re-gime on a global scale. Challenges arise when assessing the impacts of climate change on the local scale for water resources management proposes, especially for low mountain headwater catch-ments that not only serve as important water towers for local communities, but also have distinct hydrological characteristics. Until now, no low flow or hydrological drought studies have been carried out on the Lauter River. This study is unique in that it compares the Lauter River, a transboundary Rhine tributary with a nearby station on the River Rhine just below its confluence at the French-German border. The Lauter catchment is a mostly natural, forested catchment, however, its water course has been influenced by past and present cultural activities. Climate change disturbances cascade through the hydrologic regime right down to the local scale. As we are expecting more low flow events, the decrease in water availability could cause conflicts be-tween different water user groups in the Lauter catchment. However, the choice of different methods for identifying low flow periods may cause confusion for local water resources manag-ers. Using flow rate time series of the Lauter River between 1956 and 2022 we compare for the first time three low flow identification methods: the variable threshold method (VT), the fixed threshold method (FT), and the Standardized Streamflow Index (SSI). Similar analyses are applied and compared to the adjacent Maxau station on the Rhine River for the same time period. This study aims at 1) interpreting the differences amongst the various low flow identification methods and 2) revealing the differences in low flow characteristics of the Lauter catchment compared to the Rhine River. It appears that the FT reacts faster to direct climate or anthropogenic impacts whereas VT is more sensitive to indirect factors such as decreasing subsurface flow which is typical for small headwater catchments, such as the Lauter where flow dynamics react faster to flow disturbances. Abnormally low flow during the early Spring in tributaries such as the Lauter can help predict low flow conditions of the Rhine River during the following half year and espe-cially for the summer. The results could facilitate Early Warning of hydrological droughts and drought management for water users in the Lauter catchment and further downstream along some of the Rhine.

As the PCIe 6.0 specification places higher requirements on signal integrity and transmission la-tency, it becomes especially important to improve signal transmission performance at the physical layer of the transceiver interface. Retimer circuit as a key component of high-speed serial interface, its delay and jitter size directly affect the overall performance of PCIe. For the conventional Retimer circuit with large latency and low jitter performance, this paper proposes a low latency and low jitter Retimer circuit based on CDR+PLL architecture for PCIe 6.0, using a jitter canceling filter circuit to eliminate the frequency difference between the retiming clock and data, reduce the retiming clock jitter, and improve the quality of Retimer output data; The data is sampled using the retiming clock and then output, avoiding the problem of large penetration latency of con-ventional Retimer circuits. The circuit is designed using CMOS 28nm process. Simulation results show that when 112Gbps PAM4 data is input to the Retimer circuit, the Retimer penetration la-tency is 27.3 ps, which is 83.5% lower than the conventional Retimer structure; the output data jitter is 741 fs, a 31.4% reduction compared to the conventional Retimer structure.

Objective: To analyze the clinical and economic impact of community-onset urinary tract infections (UTI) caused by extended-spectrum beta-lactamase (ESBL)-producing Klebsiella pneumoniae requiring hospitalization. Methods: A retrospective cohort study included all adults with UTI caused by K. pneumoniae admitted to a tertiary care hospital in Barcelona, Spain, between 2011 and 2015. Demographic, clinical and economic data were analyzed. Results: One hundred and seventy-three episodes of UTI caused by K. pneumoniae were studied; 112 were non-ESBL-producing and 61 ESBL-producing. Multivariate analysis identified ESBL production, acute confusional state associated with UTI, shock, and time to adequate treatment as risk factors for clinical failure during the first 7 days. Economic analysis showed differences between ESBL-producing and non-ESBL-producing K. pneumoniae for the total cost of hospitalization per episode (mean 6,718 € vs 3,688 € respectively). Multivariate analysis of the higher costs of UTI episodes found statistically significant differences for ESBL production and time to adequate treatment. Conclusion: UTI caused by ESBL-producing K. pneumoniae requiring hospitalization, and time to adequate antimicrobial therapy are associated with worse clinical and economic outcomes.

Fixed offshore wind turbines continue to be developed for high latitude areas where not only wind and wave loads need to be considered, but also moving sea ice. Current rules and regulations for the design of fixed offshore structures in ice-covered waters do not adequately consider effects of ice loading and its stochastic nature on fatigue life of the structure. Ice crushing on such structures results in ice-induced vibrations, which can be represented by loading the structure using a variable-amplitude loading (VAL) sequence. Typical offshore load spectra are developed for wave and wind loading. Thus, a combined VAL spectrum is developed for wind, wave, and ice action. To this goal, numerical models are used to simulate the dynamic ice-, wind-, and wave-structure interaction. The stress time-history at an exemplarily selected critical point in an offshore wind energy monopile support structure is extracted from the model and translated into a VAL sequence, which can then be used as a loading sequence for the fatigue assessment or fatigue testing of welded joints of offshore wind turbine support structures. This study presents the approach to determine combined load spectra and standardized time series for wind, wave, and ice action.

As we are aware Information Technology had its cutting-edge lifestyle from the overdue sixties of the remaining century whilst the Arpanet become introduced, funded with the aid of using the branch of protection of the USA. After that, the IT enterprise has come a protracted manner to its cutting-edge form in which its miles gambling a dominant function in each sphere of life. It has made innovative modifications in facts amassing and dissemination and worldwide communication. It is growing into a surely paperless painting environment. Also, we can now ship a message very without difficulty to everywhere withinside the international in seconds. From a schooling factor of view, we can have a digital elegance in which the teacher ought to take a seat down in any part of the arena and his college students scattered in all exceptional elements of the arena via video convention with the presentation of look at substances in addition to query and solution sessions. A health practitioner now sitting in any part of the arena ought to carry out a surgical procedure in which the affected person is mendacity in some other part of the arena. These work examples display where we stand these days compared to what has become 1/2 of a century back. But as we recognize, nothing on this international is only correct as the whole thing has a darkish side. In this paper, we might speak about the deserves and demerits of enforcing IT globally and in which we are heading withinside the future.

The effect of the COVID-19 pandemic in a developing country like Bangladesh is enormous. A research conducted by South Asian network of Economic Modelling predicted that the pandemic could double the poverty. But it is not that only the socioeconomic condition is dropping in Bangladesh, the impact of COVID-19 pandemic is manifold. The poor condition of Bangladesh's health sector has also been exposed due to the pandemic. People are not getting proper treatment due to lack of isolation beds, oxygen, ICU etc. The health sector of Bangladesh is not much developed and now with this pandemic it has become impossible to provide treatment facility for all the patients. Education sector, which is the backbone of a country,has also been greatly affected by the pandemic. We know that different types of cultural occasions are an inherited tradition of Bangladesh, COVID-19 have not even spared these traditions, all the cultural programes and festivals have been cancelled due to this pandemic.In this paper, our aim is to present the present status of all these sectors.

The aim of this study was to examine the post-injury psychological impact looking for to avoid sources of health issues. We have analyzed differences in the stress, anxiety and depression levels between male and female football players who have suffered at least one injury during the last season played respect to similar players who have not been injured. A descriptive cross-sectional design was used. The participants were 187 football players and data on the player’s injuries were collected. A Self-reported Questionnaire collected number, type and severity of injuries sustained during the previous sports season (twelve months), and also the player’s current situation being injured or not injured. To evaluate the psychological variables, the DASS-21 questionnaire was used. Results indicated that the male injured players presented anxiety levels higher than those who were non-injured. When we observe the female players’ data, the stress levels of the non-injured ones are higher than those of the injured players. Regarding the non-injured athletes, results showed that the female non-injured players presented values in anxiety higher than those corresponding to the non-injured male players. Thus, sport injury affects mental health issues such as anxiety and stress, and in a different way regarding gender.

This paper presents laboratory devices on which experimental measurements were carried out to prove the validity of the assumption about the reduction of vibrations transmitted to the conveyor belt structure generated by the impact forces of falling material grains in the places of transfer or on the hoppers of conveyor belts. In order to limit damage to the conveyor belts caused by the impact of the sharp edges of material grains, conveyor belts are supported by impact rollers or impact rubber rods in the places of transfers and on the hoppers of belt conveyors. The flattened ends of the impact rollers are inserted into the grooves of steel brackets installed on the supports of the fixed conveyor idlers of a conventional design. In this paper, a special modification of the fixed conveyor idler is presented, which consists of inserting plastic brackets into the structurally modified roller axle holders of the fixed conveyor idler. Measurements were carried out on the first laboratory device, which showed that the specially modified fixed conveyor idler resulted in a higher damping of up to 15% of the impact forces of the falling weight on the rubberized hoop of the impact roller shell compared to the conventional fixed conveyor idler design. Measurements carried out on the second laboratory device show that the effective vibration velocity values detected at the points where the impact roller axis fits into the fixed roller table holder, i.e. points B and D, are higher than when using plastic brackets, up to 6% for a 108 mm diameter roller, compared to steel impact roller brackets.

As the increase threat of flood risk and environmental safety due to the urbanization, Sponge city research has been attracting extensive attention both in practical and theoretical research field. To date, there are only scattered studies about Sponge city. Moreover, vary names of Sponge city prevalent in different countries, which leads to disconnection of literature in the same field of Sponge city. In this paper, a thorough systematic literature mining of Sponge city is presented. A literature analysis system is created, which includes literature export from Web of Sciences and systematic analysis via NoteExpress and CiteSpace. Some literature statistical results are derived. Challenges and opportunities for future research are anticipated. Our goals are to promote this promising thought, summarize past research, and identify issues for future research to create impacts on the practice of Sponge city.

Continuous rigid frame bridges across valleys are often at the risk of rockfalls caused by heavy rainfalls, earthquakes and debris flows in a mountainous country. Hollow thin-walled bridge piers (HTWBP) in valleys are exposed to the threat of the impact of accidental rockfalls. In the current research, ANSYS/LS-DYNA is used to establish a high-precision rockfall-HTWBP model. The rockfall-HTWBP model is verified against a scaled impact test of a previous research. A mesh independence test is also performed to obtained an appropriate mesh size. Based on the rockfall-HTWBP model, the impact force, damage and dynamic response characteristics of HTWBP under the rockfall impact are studied. In addition, a damage assessment criteria is proposed based on the response surface model combined with Central Composite Design method and Box-Behnken Design method. The main conclusions are as follows: 1）The impact force of rockfall has a substantial impulse characteristic, and the duration of the impulse load is approximately 0.01s. 2）The impacted surface of the pier is dominated by the final elliptic damage with the conical and strip damage areas as the symmetry axis. The cross-sectional damage mode is compression failure in the impact area and shear failure at the corner. 3）The maximum displacement occurs in the middle height of the pier. The maximum displacement increases with impact height, impact velocity and rockfall diameter and decreases with the uniaxial compressive strength of the concrete. 4) The initial impact velocity and diameter of the rockfall are the most significant parameters affecting the damage indices. In addition, a damage assessment method with a damage zoning diagram based on the response surface method is established for the fast assessment of the damage level of impacted HTWBP.

Recently, more and more countries are entering the global race for university competitiveness. On the one hand, global rankings are a convenient tool for quantitative analysis. On the other hand, their indicators are often difficult to quickly calculate, they often contradict each other. We thought about using widely available indicators for a quick analysis of the University's publication strategy. We opted for the normalized citation indicators available in SciVal analytical tool, i.e. Source Normalized Impact per Paper (SNIP) and Field-Weighted Citation Impact (FWCI). We have demonstrated the possibility of applying the correlation analysis to the impact indicators of a document and a journal on the sample of the social and humanitarian fields at Peoples' Friendship University of Russia. Particular attention was paid to the application of the results in practice.

African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

A novel low-power MOS-only voltage reference is presented. The Enz-Krummenacher-Vittoz (EKV) model is adopted to provide a new perspective on the operating principle. The normalized charge density, introduced as a new variable, serves as an indicator when trimming the output temperature coefficient. The proposed voltage reference consists of a specific current generator and a 5-bit trimmable load. Thanks to the well-match between the current source stage and the output stage, the non-linear temperature dependence of carrier mobility is automatically canceled out. The circuit is designed in 55 nm COMS technology. The operating temperature ranges from -40 ∘C to 120 ∘C. The average temperature coefficient of the output voltage can be reduced to 21.7 ppm/∘C by trimming. The power consumption is only 23.2 nW with a supply voltage of 0.8 V. The line sensitivity and the power supply rejection ratio at 100 Hz are 0.011 %/V and -89 dB respectively.

Patients with chronic (CM) and high frequency episodic migraine (HFEM) report cognitive complaints that contribute to migraine burden. Although, there is little evidence about the ef-fects of migraine treatments on these symptoms. Objective: To evaluate the effect of preventive treatment on the impact of cognitive symptoms, specifically the ability to concentrate, in individuals with CM and HFEM. Methods: Prospective cohort study in patients with CM and HFEM initiating treatment with botulinum toxin (BT) or anti-CGRP/R monoclonal antibodies (mAbs). Patients were evaluated at baseline and after 3 months of treatment, using a headache diary and a question about the im-pact of migraine attacks on concentration (never, rarely, sometimes, often, and always). Results: 108 patients (105 females, 44.3 years of age on average), 75% with CM and 27% with HFEM were included, 55 received a first session of BT and 53 received 3 injections of a monthly mAb. In both groups, there was a significant decline on the impact of migraine in concentration (related samples Wilcoxon signed rank test <0.001) compared to baseline. Reduction in monthly headache days was the main predictor of any concentration improvement, while treatment group, age, ongoing medication with topiramate or baseline medication overuse were not sig-nificant. Conclusion: Preventive treatment of HFEM or CM with drugs not acting on central nervous sys-tem is associated with a decrease of the impact of migraine attacks on concentration, predicted by the decline in headache days. These results indicate that migraine preventive treatment also improves non-pain symptoms, which is relevant given the contribution of cognitive complaints to the impact of headache attacks

Globally 703 000 people commit suicide (4th leading cause of mortality among 15-29 year-olds, 1.4% of all deaths globally) every year, which have a negative effect on families, colleagues, and societies. India accounts for 36.6 percent of global suicide in women and 24.3 percent among men, while having only 17.8 percent of the global population, also remarkable fact is that the suicide ratio for female is 14.7 per 100,000 compared to 21.2 per 100,000 of male which is 2.1 times the global average in female, while 1.4 times higher for men. COVID-19 (coronavirus disease-2019) pandemic has certainly affected the physical, mental, economical and social well being of global population directly or indirectly in different ways. Deteriorating physical, mental, economical and social health of an individual could increase the suicidal tendency, leading to accidents and suicide. This study tried to find out the COVID-19 pandemic situation impact on accidental death as well as suicide rates in India. The study period is from 1st January 1967 to 31st December 2021, to assess the effect of the COVID-19 pandemic situation on suicide and accidental death rates. This study revealed that the suicide deaths percentage among males increased significantly in comparison to females in COVID-19 era and actual count and incidence also increased. This study revealed that the mean accidental death and suicide both increased during COVID period of study as compared to pre-pandemic whole period from 1967 by 25.47 % and 30.61% respectively. Alternatively we can say that the accidental death and suicides increased significantly in India, which is largely preventable.

The thermal insulation properties of building walls are critical to the overall energy efficiency and comfort of a building. One important factor that can affect these properties is the type of bricks used in construction. Bricks can vary in their geometry and thermal coefficient, which can impact their ability to transfer heat through the wall. The geometry of a brick can affect its thermal properties by altering the amount of air trapped within it and the surface area available for heat transfer. Hollow bricks or those with complex geometries may have lower thermal conductivity than regular solid bricks due to the air pockets trapped within them. Conversely, larger surface areas on the exterior of the brick can increase heat transfer. The thermal coefficient of clay, a common material used in brick production, is another important factor. Clay has a relatively low thermal conductivity, meaning it is a poor conductor of heat. However, the quality of the clay, as well as the firing temperature and duration used in brick production, can impact its thermal coefficient. Higher firing temperatures and longer firing times can result in a more compact and dense clay brick, which can improve its thermal properties. In summary, the thermal insulation properties of building walls can be significantly affected by the type of bricks used in their construction. It is important to consider the geometry and thermal coefficient of the bricks when designing a building to achieve the desired level of thermal insulation. By selecting bricks with appropriate properties, designers can help to improve the energy efficiency and comfort of the building while reducing its environmental impact.

This study aims to examine households' perceptions of the socio-cultural, economic, and environmental impacts of ecotourism in the protected area, focusing on Simien Mountain National Park, North west Ethiopia. Using a mixed research approach with a sequential explanatory design, we collected data through a single-round cross-sectional survey, interviews, focus groups, discussions, and secondary sources of information. Three districts were selected using a multi-stage sampling method, and 397 respondents were surveyed. We analyzed the quantitative data using percentages, averages, t-tests, ANOVA, and regression models, and examined the qualitative data using thematic analysis. Our findings suggest that households living in the park generally perceived the social, economic, and environmental impacts of ecotourism as favorable. However, the study also revealed that the benefits of tourism are not being fully utilized, indicating the potential for further development. We found significant differences in how people perceived ecotourism based on their gender, education, and residence location. Specifically, men and respondents with higher levels of education were more likely to perceive ecotourism positively. The logistic regression model revealed a statistically significant direct cause-and-effect relationship between three demographic factors of household respondents' participation in ecotourism (dependent variable) and gender (B = 1.85, p = 0.023), educational attainment (B = 0.23, p = 0.003), and location (B = 0.42, p = 0.041). In light of these findings, the authors recommend that the local government and the Ethiopian Wildlife Conservation Agency should develop sustainable plans for tourism that will benefit nearby communities and improve living conditions in the park.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), also known globally as COVID-19, originated in December 2019 in Wuhan, Hubei province in China and has rapidly spread across the globe ever since. The first recorded case in sub-Saharan Africa was in Nigeria, on the 25th February, 2020. The virus continues to spread, and new variants of the disease have emerged, the number of deaths and new infections in the countries of sub-Saharan Africa has been relatively low compared to predictive models. This could be due to several factors, such as slower transmission dynamics of the virus, a lower-case fatality rate, or a lack of testing or reliable data. Whilst this may also, in part, be due to the robustness of the nations' public health responses, there is scarce reporting on the specifics of this. However, emerging research has demonstrated that various environmental factors could influence virus transmission. The study adopted collected meteorological data that was critically analysed and discussed. The impact of three factors in the context of sub-Saharan African nations: temperature, ultraviolet (UV) exposure and pre-existing infection with Plasmodium (malaria) were discussed. These factors were discussed critically in light of the reduced rates of transmission and mortality observed.

Tourism may not sustainably support territories with limited natural resource stock as islands. The volume in visitor arrivals and the industry investments can increase the pressure even beyond sustainable levels. There is an evident and unresolved tension between these two great polarities, sustainability and economic growth driven by tourism. The aim for policymakers is to find an acceptable equilibrium between these two dimensions. This paper investigates the tourism evolution between 2007 and 2019 in 15 Mediterranean islands, comparing the tourism pressures through statistical indicators. The analysis will compare tourism demand and supply trends in these contexts. The performances will be evaluated to identify the Islands positioning between sustainability needs and tourism development opportunities considering post-covid-19 challenges.

Abstract Mastitis is a common disease of dairy animals. The source of mastitis infection may be regarded as contagious or environmental. A wide range of pathogens including bacteria, viruses, fungi, and the toxins of these pathogens can cause the disease. Mastitis is generally associated with poor hygienic and husbandry practices. The primary reservoir of infection is the mammary gland. The infectious agent enters through the milk canal, interacts with the mammary tissue/cells and multiplies. Most contagious mastitis causing pathogens are spread during milking. Most other species are opportunistic invaders from the cow's environment.

The COVID-19 has caused gigantic negative effects on populace wellbeing, society, education, and the economy in Bangladesh. The aim is to deliver a comprehensive overview of the observed and the possible impacts that could appear in the coming days. The study is based on secondary information. During the early period, due to a lack of accurate facts about the case affected and death tension up-and-down among the nations. The total number of confirmed cases is increasing following geometric patterns in Bangladesh. Dairy farmers, vegetable producers, pharmaceuticals, poultry farmers are in deep crisis due to lower prices. Also, the pandemic has seriously affected educational systems, banking, FDI, ready-made garments, remittances, etc Finally, it is not possible to mitigate the effects of pandemic individually but the integrated effort from the state authority as well as concern people of all sectors need to come forward.

Aflatoxins are a known cause of primary liver cancer in Mozambique since pre-independence epidemiological studies. However, their impact goes beyond the public health, affecting the country’s economy and raising legal concerns. As a developing country endemic for Aspergillus, the nation has been struggling to keep pace with external trade quality demands, delicate policy making, still dealing with the farmers’ limitations to control the contamination. The contamination shows variations over time, space and the different commodities. Considering the recommendations of the Codex Alimentarius, the major crops will be highly implicated unless there is major intervention from the authorities to control the toxins.

This article describes the POTENTIALS project, which aimed to develop business models for the reuse of former industrial and mining sites in different regions. The project focused on the creation of eco-industrial parks as a result to enable sustainable energy production and reduce waste and pollution. A key aspect was the Territorial Impact Assessment (TIA), a new and complex policy assessment tool. Therefore, the TEQUILA (Territorial Efficiency Quality and Identity Layer Assessment) approach is used to describe the TIA and emphasizes its application in assessing the impact of EU policies and projects on territorial cohesion. It underlines the need for a differentiated understanding of the regional characteristics and potential impacts of policies; and stresses the importance of regionalized impact models for the assessment. Furthermore, the process and results of applying the TEQUILA methodology to assess the territorial impact of different scenarios of business models within the POTENTIALS project is given.

The European Green Deal has set a concrete strategic plan to increase farm sustainability. At the same time, the current global challenges, due to climate change and fuels and commodity market crisis, combined with the Covid-19 pandemic and the ongoing war in Ukraine, comprise the need for quality food, but also the reduction of negative external effects of agricultural production, with fair remuneration for the farmers. In response, precision agriculture has great potential to contribute to the sustainable development. Precision agriculture is a farming management that provides a holistic system approach to managing the spatial and temporal crop and soil variability within a field to improve the farm’s performance and sustainability. However, farmers are still hesitant to adopt it. On these premises, the study aims to evaluate the impacts of precision agriculture technologies on farm profitability, agronomic and environmental management by farmers adopting (or not) these technologies, using the case study method. In detail, the work focuses on the period 2014-2022 for two farms that cultivate durum wheat in Central Italy. The results suggest that the implementation of precision technologies can guarantee economic and agri-environmental efficiency. Results could serve as a basis for developing a program to start training in farms as well as suggest policy strategies.

This paper identifies the characteristics of the farmer that affect the degree of farmer’s perceived-impact of climate change (CC). We use data from the Indonesian Rice Farm Household survey consisting of 87,330 farmers. An ordered probit regression model was used to estimate the effect of each variable on the degree of perceived-impact of CC. The results of this study confirm the previous empirical studies. Several variables that have been identified as having a positive effect on farmer adaptation practices such as farmer education, land tenure, irrigation infrastructure, cropping system, chemical fertilizer application, access to extension services and participation in farmer group affect the degree of CC perceived-impact negatively. However, a different result was found in the estimation of the gender variable. We found that female farmer has a higher resilience toward CC than the male farmer does. Furthermore, the female farmer has a more positive perception about future farming conditions than the male does. Finally, we suggest that the implementation of national adaptation policy should prioritize more to the farmer with insecure land tenure and utilize and expand the channel of agricultural extension services to deliver the planned adaptation policy.

Covid-19 pandemic lockdown has slow down the world economic system. The pandemic has cleared the roads, close factories and grounded planes causing severe economic challenges. The damaging impact of the pandemic amid lockdown has been a blessing in guise for the environment because of significant drop in pollution level as transport and industrial sectors shutdown. Transport and industrial sectors are major contributors to environmental degradation through various emissions as a result of fossil fuel consumption. Energy consumed by transport and industrial sectors will have to shift to viable, readily available, economically and environmentally friendly with no carbon build up post Covid-19 pandemic. Hydrogen energy remains the best alternative option technologies containing green house gas emission and pollutions of several forms. Hydrogen holds the potential to provide a clean, reliable, renewable and economical source of energy for meeting the growing and unending global energy needs post pandemic. The present paper explores the economic feasibility and potential of hydrogen to serve as a competitive fuel option post pandemic. In this paper, the role of hydrogen as an energy carrier hydrogen economy structure, potential of hydrogen economy, hydrogen production methods, hydrogen application and the economic and environmental importance of hydrogen as a viable fuel option post covid-19 pandemic were discussed. There will be a surge in demand and investment for hydrogen economy post Covid-19.

Low volatility ETFs have become popular in recent year because investors are starting to understand the advantages involved in investing in those ETFs compared to traditional index investment. In this research I have examined the performance of six popular low volatility ETFs, four of them invest in U.S stocks and the other two invest in other developed and emerging markets. Results have pointed out that not only five of the low volatility ETFs have exposed their investors to lower risk, four of them have also produced higher returns. The advantage of investing in low volatility ETFs is prominent in the U.S stock market. All three sizes of stocks categories (Large, Mid and Small Capitalization) low volatility ETFs have outperformed their indexes bench marks in terms of risk and returns. For the non U.S stock investing, while no advantage have been found for investing in low volatility ETFs for developed countries, significant lower risk was found for emerging markets.

Logistics industry has been found to be among the key sources of carbon emission. In Vietnam logistics industry, there is a considerable difference between the number of foreign and Vietnamese firms as well as the proportion of markets that they are taking. This study is to research the low-carbon emission measures conducted by domestic and foreign invested logistics service providers (LSPs) and compare the results of the two groups. Both qualitative and quantitative approaches are applied. Literatures in relevant fields are reviewed and expert opinions are taken for structuring a questionnaire which was later distributed to 279 LSPs, with 166 returned and 159 being valid for data calculation. The results imply that there are differences in extension of applications of low-carbon practices between foreign and domestic firms. Except for transport mode switch and energy-saving lighting, the other practices witness that adoption levels of foreign LSPs are higher than their counterparts, which is possibly thanks to their global operation, more comfortable capital resources and awareness level of green initiative necessity. In conclusion, a comparison between the application conducted by foreign-invested firms and domestic ones, which has not been investigated before, was made.

The rise of fintech in the financial sector presents a transformative shift towards digitalization and sustainability, leveraging technologies like AI to minimize environmental footprint. Neobanks not only challenge traditional banking models but also offer innovative solutions that align with sustainable objectives. The purpose of this paper is to analyze the impact of neobanks on global sustainability, from economic, environmental, and social point of view. A comprehensive literature review of existing literature and current sustainable practices of neobanks was conducted. We have found that neobanks significantly positively contribute towards environmental sustainability with reduced paper use and logistics requirements of banking services. By offering more accessible and affordable banking services they importantly contribute towards higher financial inclusion, and with innovative products towards more competitive and innovative financial markets. AI-based tools they employ are increasing financial literacy and social inclusion. We also highlight concerns regarding electronic waste management, potential high energy consumption, required digital literacy and cybersecurity risks. We conclude that despite the mentioned risks, neobanks importantly contribute to global sustainability in many ways, and will even more in the future. Our findings can help neobanks shape sustainable practices and guide policymaking, as well as spread awareness of sustainable impact of banking services.

Depressions containing partially molten rocks were investigated in Quaternary pebbly sedi-ments in Alpine foreland in Bavaria, Germany. Ruins of limekilns from 18-19th centuries are abundant around Seeshaupt. They are usually associated with earthworks for fuel feeding and protection from wind. Depressions contain partially molten stones from furnace walls, with lime and burnt loam remnants. On the surface of pebbles (typically gneisses), green glass formed with chemical composition possibly affected by moderately volatile components of wood biomass, mainly K and Cu. Thermoplastic deformation of pebbles is limited and the sur-face melt deformation points to slow flow. At Emmerting, on the other hand, two walled circu-lar depressions which lack additional earthworks have been identified as possible impact cra-ters. Thermally affected pebbles show much more intense deformation. Colorless to greenish glass, also K and Cu enriched, usually forms only thin surface coatings, in places covered by younger melt extruded from pebble interior. Burnt loam is missing. At Grabenstätt-Kaltenbach, a depression of unclear origin was investigated. Morphologically, it matches craters rather than limekilns, but anthropogenic contamination (brick-like material) is probable. The rare molten samples do not display extreme deformation features. The thermally affected stones, mainly those from Emmerting, have elevated magnetic susceptibility.

This analyses the impact of competition on liquidity creation in the banking industry of the United States. For the purposes of this paper panel data of US banks for the period of 1976-2000 is chosen as a sample. The plausible endogeneity issue is addressed by employing instrumental variables and then implementing two stages least squares method. Besides this, crisis period of 1990-1992 is also analyzed to compare effect with in “normal times”. The results show that decrease in the level of competition negatively affects the liquidity creation ability of banks in the US and this impact is even more negative during the crisis period.

This article seeks to understand how the incorporation of new scientific articles in the field of urban studies on topics related to housing, manage to impact specialized media. In other words, it seeks to identify whether social science that publishes findings on housing has become less relevant over time, as occurs in other areas of knowledge. To do this, data is collected from the Web of Science of the urban studies categories, using as a filter that either in the title, keywords or abstract contain the word "housing". With this database, all the DOIs of the indexed articles are taken and it is reviewed whether those new DOIs incorporated into the knowledge database have impacted in relation to new citations that of said DOIs that are added in the future. More than looking for the impact of an article for the particular, it is sought to review added values. It is identified that the only disruptive moment occurred after the 2008 real estate crisis. This finding emphasizes the importance of looking for new paths for the production of knowledge on housing that is novel and original, that manages to break with an apparent trend of scarce innovation or lack of knowledge among peers of what is being published in the matter.

The advent of artificial intelligence has ushered in a new era of digital tools, including chatbots and virtual assistants, for educational purposes. ChatGPT, an advanced language model, has gained popularity as an educational aid. However, concerns have emerged regarding its potential negative impact on student learning behavior. This experimental research study investigates the influence of ChatGPT on student learning behavior and offers insights into its potential drawbacks.

This study examines the impact of alcohol concentration on the precision of unmanned aerial vehicle (UAV) operations. While the impact of alcohol impairment on various activities is well documented, its specific influence on drone piloting accuracy remains less studied. To address this, we carried out empirical research using an original methodology and a real-world environment. The study involved a group of 35 participants performing a series of flights using a selected drone (DJI Mavic2 Pro) on a bespoke obstacle route. Between each flight series, participants consumed a measured amount of alcohol, designed to incrementally increase their blood alcohol concentration monitored via breath tests. The precision of the drone pilot was evaluated by comparing various parameters from successive test flights, such as time, distance, average speed, and incident frequency, against a baseline trial executed with zero alcohol concentration. Our results indicate a noticeable decline in UAV piloting precision corresponding with increasing alcohol concentration. Parameters such as flight time, distance, speed, and incident frequency all demonstrated this trend. We conclude that alcohol consumption detrimentally affects the accuracy of drone operations. These findings underscore the need for clear policies and guidelines regarding the operation of UAVs under the influence of alcohol.

Artificial Intelligence (AI) stands as an emerging technology poised to reshape various facets of our daily lives, with a particularly noteworthy influence on the labor market. In Morocco, AI adoption has commenced in diverse sectors, including finance, insurance, and telecommunications, opening up fresh avenues for employment. Nevertheless, this technological shift also ushers in challenges for Moroccan workers, necessitating training and upskilling to effectively engage with AI-driven systems. Within this article, we delve into the burgeoning impact of AI on the Moroccan economy and job landscape, delving into both the opportunities and obstacles that accompany its proliferation. Furthermore, we explore strategies that authorities and businesses can employ to harness the benefits of AI while mitigating its potential adverse effects on Morocco's workforce.

In this work a solution-annealed AISI 316H grade austenitic stainless steel was studied in terms of investigating the electrolytic hydrogen charging effects on the resulting Charpy impact toughness and dry sliding tribological behavior. Conventional Charpy impact bending tests were employed to study the mechanical response of the investigated material to dynamic loading conditions, whereas dry linear sliding tribological tests were used to study the material friction and wear behavior. The obtained mechanical and tribological properties were correlated with corresponding fracture and tribological mechanisms determined from morphological observations of fracture surfaces and tribological tracks. The applied testing procedures were individually carried out for the non-hydrogenated, hydrogen-charged, and dehydrogenated material conditions. The observed changes of individual properties due to applied hydrogen charging were rather small which indicated good resistance of the solution-annealed AISI 316H steel against material degradation in currently used electrolytic hydrogenation conditions.

Impact force and maximum velocity are important indicators of kick efficiency in fighting activities. Therefore, this systematic review compared the front kick (FK) and roundhouse kick (RK), including maximal and impact force, maximum velocity, maximum angular velocity, and execution time, at different target types and experience levels. The Web of Science, SportDiscus, and PubMed were systematically searched from January 1982 to May 2022, according to PRISMA guidelines. The normalized kicking values were compared using one-way ANOVA. Eighteen articles, including FK with a pooled sample of 113 elite men, 109 sub-elite men, and 46 novices, and 25 articles, including RK with a sample of 238 elite men, 143 sub-elite men, and 27 novice men, fulfilled the inclusion criteria. The primary findings were that the impact forces of FK were higher than RK for the novice, sub-elite, and elite groups by 47% (p<0.01), 92% (p<0.01), and 120% (p<0.01), respectively. Moreover, the maximum foot velocity of RK was faster than FK for the sub-elite and elite groups by 44% (p<0.01) and 48% (p<0.01), respectively. The Elite group had 65% (p<0.01) higher knee extension angular velocity within RK than FK, and 138% (p<0.01) higher hip extension angular velocity within FK than RK.

Metal fabrications experience complex physical metallurgical processes during additive manufacturing, leading to residual stress and coarse microstructure with directional growth. It significantly affects the comprehensive performance of the fabrications, which limits the application of additive manufacturing. Ultrasonic impact treatment (UIT), as a strengthening means to assist additive manufacturing, can effectively improve the stress state and refine the microstructure and the comprehensive performance. This paper introduces the effect of UIT on AM metal fabrications on microstructure morphology, stress distribution, surface roughness, internal defects, and comprehensive performance to gain a deeper understanding of the role of UIT on additively manufactured metal fabrications, which is based on the working principle and effect of process parameters. In addition, the strengthening mechanism of UIT in additive manufacturing is described from the perspective of surface plastic deformation and substructure formation, providing support for the shape and property control of metal fabrications in the process of additive manufacturing assisted by UIT. Finally, the issues that need to be studied in depth on UIT in additive manufacturing are summarized, and an outlook on future research directions is taken.

Engineers make things, make things work, and make things work better and easier. This kind of knowledge is crucial for innovation, and much of the explicit knowledge developed by engineers is embodied in scientific publications. In this paper, we analyze the evolution of publications and citations in Engineering in a middle-income country such as Mexico. Using a database of all Mexican publications in Web of Science from 2004 to 2017, we explore the characteristics of publications that tend to have the greatest impact; this is the highest number of citations. Among the variables studied are the type of collaboration (no collaboration, domestic, bilateral, or multilateral), the number of coauthors and countries, the language of the article, controlling for a coauthor from the USA and the affiliation institution of the Mexican author(s). Our results emphasize the overall importance of joint international efforts and suggest that publications with the highest number of citations are those with multinational collaboration (coauthors from three or more countries), written in English, and when one of the coauthors is from the USA.

The suppression of natural spaces due to the urban sprawl and increase of the built and agricultural environments has impacted the water resources quality, especially in areas with high population density, as the metropolitan regions. Considering the advance in Brazilian environmental legal framework, the present study aims to verify whether land use has still significantly affected water quality, through a case study in the Stones River watershed, a peri-urban river basin at a metropolitan region, Brazil. Analysis of physical-chemical indicators, collected at several sample points with different land-use (urban areas, commercial forestry, riparian forestry, mixed vegetation, pasture, and sugar cane plantation) at different seasons of the year (dry and rainy) were carried out. As a result, it was verified some statistically significant spatiotemporal effects on the of water quality caused associated to the land-use. In conclusion, in spite of the advances in the Brazilian law, land-use has still significantly affected the water quality, demanding public policies and decisions, so that effective compliance with legal guidelines is ensured.

We present the prototype and analytical model of a miniaturized impact actuation mechanism, providing a fast out-of-plane displacement to accelerate objects against gravity, allowing for freely moving objects and hence for large displacements without the need of cantilevers. To achieve the necessary high speed, we chose a piezo electric stack actuator driven by a high-current pulse generator, connected to a rigid support and a rigid three-point contact with the object. We describe this mechanism with a spring-mass model and compare various inertial masses, all of them spheres, from different diameters and materials. As expected, we found that larger flight heights are achieved by harder projectiles, achieving, e.g., approx. 3 mm displacement for a 3 mm steel sphere using a 3x3x2 mm³ piezo stack.

[Research Objective] In the context of the rapid development of digital governance, understanding and analyzing the burden level of digital tools in the process of serving digital governance from multiple perspectives is an important prerequisite for improving the capacity and accuracy of government digital governance, promoting sustainable public participation, and maximizing digital value in the new era. [Research Method] By constructing a model of the burden of digital tools caused by technical, organizational and environmental factors on the public based on the TOE framework, using SPSS for data testing based on 275 research questionnaires, and using fuzzy set qualitative comparative analysis (fsQCA) to explore the linkage ways and paths of the burden-increasing effect of digital tools in a holistic perspective. [Research findings] does not constitute a necessary condition for high levels of digital tool affordances under a single condition, but improving users' digital literacy plays a more general role in optimising the efficiency of digital tool use. According to the results, there are five dominant patterns that have a significant impact, i.e. the driving paths that lead to high levels of digital tool affordability are characterised by a "homogeneous approach". In the cross-group study, significant differences were found in the driving paths of high digital tool affordability by group, depending on the level of digital tool mastery. This paper suggests that the government should continue to pay attention to affordability levels, rationalise the use of financial resources, improve the level of digital tool adaptation, and innovate the existing performance evaluation system for digital governance indicators.

The monitoring of river discharge is vital for the correct management of water resources. A worldwide facility used for measuring discharge are flat-V gauging weirs. These structures consist of a small weir, with a triangular cross-section and a flat “V”-shaped notch. Their extensive use is a consequence of their utility in the measurement of both low and high flow conditions. However, depending on their size, local morphology and river discharge can act as full or partial hydraulic barriers to fish migration. To give answer to this question, the present work studies fish passage performance over flat-V weirs considering their hydraulic performance. For this, radio-tracking and video monitoring observations were combined with computational fluid dynamics (CFD) models in two flat-V weirs, using Iberian barbel (Luciobarbus bocagei) as target species. Results show that fish passage is conditioned by both hydraulic and behavioral processes, providing evidences about the scenarios where flat-V weirs may act as full or partial barriers to upstream movements. For the studied flat-V weirs, a discharge range of 0.27-8 m3/s, with a water drop difference between upstream and downstream water levels lower than 0.7 m and a depth downstream the weir higher than 0.30 m can be considered as an effective passage situation for barbels. These findings are of interest to quantify flat-V weir impacts, for engineering applications and to establish managing or retrofitting actions when required.

Based on the total scholarly article output of Norway, we investigated the coverage and degree of openness according to three bibliographic services 1) Google Scholar, 2) oaDOI by Impact Story and 3) 1findr by 1science. According to Google Scholar, we find that more than 70% of all Norwegian articles are openly available. However, degrees are profoundly lower according to oaDOI and 1findr, respectively 31% and 52%. Varying degrees are mainly caused by different interpretations of openness, with oaDOI being most restrictive. Furthermore, open shares vary considerably by discipline, with the Medcine and Health sciences at the upper and the Humanities at the lower end. We also determined the citation frequencies using Cited-by values as of Google Scholar, applying year and subject normalization. We find a significant citation advantage for open articles. However, this is not the case for all types of openness. In fact, the category Open Access journals was by far lowest cited, indicating that young journals with a declared open access policy still lack recognition.

Ecosystem services (ES) are increasingly recognized as a means to adapt to the ongoing impact of climate change and associated impacts. However, these ES itself are facing adverse impact of climate change especially in developing countries where most of the people are dependent on these services for their livelihood. Very little is known about the relationship between the climate change and ES. Here we assess the impact of climate change on ecosystem services in ES rich landscape of Panchase Mountain Ecological Region of western Nepal. The study area was divided into three ecoregions from lowland through midland to the upland region. Focus group discussion, and key informant interview were used to elicit the required data for the study, which was further supported by transect walk, field observation and secondary source of information. Major impacts of climate change were observed are, reduced availability of water, reduced food production, forest ecosystem, shifting species composition in forest ecosystem, farmland abandonment, and their associated ecosystem services. We recommend to initiate the management actions to help ES adapt to climate change, and which in return could support the ecosystem itself and people dependent on the ES in adaptation to climate change by providing various goods and services.

We are experiencing an unprecedented urbanization process that alongside with physical, social and economic developments is having a significant impact on population’s health. Due to higher apprehensions of pollution, violence and poverty, our modern cities no longer ensure a good quality of life so they become unhealthy environments. This study aims to measure the socio-environmental and hematologic profile of residents of Santo André’s landfill – “Bairro Espírito Santo” by using the contextualization of the studied area. The research method is Observational type and from Retrospective cohort and by convenience sampling in Santo André in the Greater ABC region. The study determined a socio environmental profile and the hematologic diseases screening related to a close location to the landfill. The disease manifests itself within a broad spectrum of symptoms that causes changes in blood count parameters. The full blood counts analysis was performed, indicating that the blood counts of residents living near the landfill led to positive hematological changes and diseases like Leukopenia, Anemia, Neutropenia and lymphocytosis were the most common changes. However it is considered that the proof of the relation of cause- effect to environmental exposures that may trigger chronic manifestations in humans requires specific studies that are often complicated.

Mercury contamination in the Amazon is a significant public health concern arising from both natural sources and intensive mining activities in the region. This metal is used to separate Au from sediments, forming an amalgam that facilitates the extraction of precious metals. Accordingly, this study aimed to address the following question: What is the impact of mining on mercury contamination in the animal and human populations of the Amazon? The overall objective of this study was to conduct a systematic review of the existing literature to identify gaps in geographic coverage and assess the impact of Hg contamination on human and animal populations in the Amazon region. Our hypothesis was that higher mercury concentrations in tissue samples would be found closer to the mining areas. We employed the PECO and PRISMA-ScR protocols to collect articles published between 2017 and 2023, selected based on criteria representing projected points on a map within the biogeographic boundaries of the Amazon. Mercury concentrations increase with trophic levels, reaching high values of 3.7 µg/g in the muscles of predatory fish and 34.9 µg/g in human hair. The average level of mercury in humans exceeds 6 µg/g, surpassing tolerance levels. Although mining regions show high concentrations of Hg, the highest incidence was observed among populations with fish-based diets. Research on fish is crucial for assessing the risk to human health, given that fish are the main source of protein in the region.

Globalized in 1995 through the TRIPs Agreement, humanity’s dominant mechanism for encouraging innovations involves 20-year product patents, whose monopoly features enable innovators to reap large markups or licensing fees from early users. Exclusive reliance on this reward mechanism in the pharmaceutical sector is morally problematic for two main reasons. First, it imposes a great burden on poor people who cannot afford to buy patented treatments at monopoly prices and whose specific health problems are therefore neglected by pharmacological research. Second, it discourages pharmaceutical firms from fighting diseases at the population level with the aim of slashing their incidence. These problems can be much alleviated by establishing a supplementary alternative reward mechanism that would enable pharmaceutical innovators to exchange their monopoly privileges on a patented product for impact rewards based on the actual health gains achieved with this product. Such an international Health Impact Fund (HIF) would create powerful new incentives to develop remedies against diseases concentrated among the poor, rapidly to provide such remedies with ample care at very low prices, and to deploy them strategically to contain, suppress, and ideally to eradicate the target disease. By promoting innovations and their diffusion together, the HIF would greatly enlarge the benefits, and thereby also the cost-effectiveness, of the pharmaceutical sector, in favor of the world’s poor especially.