Photovoltaic (PV) technologies are developing rapidly as a result of their ability to reduce energy consumption from conventional sources as well as the growth of global energy expenditures. Nevertheless, several impact categories during the PV panel life cycle occur and some principal sectors are affected. These impact categories are assessed by applying life cycle analysis (LCA) techniques through various software programs, databases and methods. Such analyses of energy technologies are crucial, as they can reveal the occurrence of hazardous emissions at distinct life cycle stages. In the present paper, a PV panel impact assessment through life cycle analysis is carried out. More precisely, a combination of PV technologies—monocrystalline, multicrystalline, copper indium gallium selenide (CIGS), amorphous, and ribbon—is studied. The impact categories of ozone depletion, human toxicity, particulate matter, ionising radiation, photochemical ozone formation, acidification, eutrophication, and ecotoxicity, as well as the sectors of human health, ecosystem quality, and environment, are assessed using the openLCA software, the ecoinvent database, the eco-indicator 99, IMPACT 2002+, ReCiPe, and TRACI methods.

Life cycle assessment (LCA) is being included formally in EcoDesign regulations. Especially product carbon footprint will be mandatory in Europe. However, life cycle impact assessment including global warming potential (GWP) in LCA is hampered by several challenges. One of these is lack of water vapor characterization indexes for GWP. A life cycle inventory profile for air transport fuel including water vapor emissions is evaluated with state-of-the-art practice, i.e. EF Method and ILCD 2011 Midpoint+ and neglecting water vapors high altitude GWP compared to carbon dioxide. Then the characterization factor in GWP100 for water vapor and alternate normalization for particulates are introduced. The results are compared. The main findings are that the EF method and ILCD both generate rather realistic results for Particulate Matter and Respiratory Inorganics mid-point indicators, respectively, but the amount of premature deaths should be better allocated to different specific emissions, and that water vapor may dominate the GWP100 result over the usual carbon dioxide. LCIA mid-points need measurable and understandable bases. The common knowledge of water vapor’s GWP100 should not be neglected in LCIA for air transport and beyond where relevant.

Certain services can help avoid environmental impact in larger contexts. However, there is no commonly agreed bottom-up methodology for calculation of the total net reduction effect of specific digital services. Life Cycle Assessment (LCA) is a common denominator for most methodologies. The most common method is the Attributional LCA (ALCA), and recently the emerging handprint ALCA estimating so-called positive environmental impacts. Moreover, Consequential LCA (CLCA) can be used to capture market effects. The third conceptual approach is Input-Output LCA. The purpose is to propose and test a new method based on some of the existing ones. The existing concepts are compared and a synthesis is made to create a practical but still useful method. The new method is applied to two illustrative cases in the Information and Communication Technology (ICT) domain; the introduction of a 5G enabled drone for pipe inspection and the 5G enabled health consultation. Compared to simplified ALCA, the difference between the absolute score for the baseline system and the target system changes up to 15% when the proposed simplified CLCA (SCLCA) method is used. The results show that SCLCA, when combined with analytical methods for expressing digital ICT services’ own impact, is a fruitful approach which is both practical and feasible.

Gas turbine installations (GTIs) are widely used to generate electrical and thermal energy mainly by burning gaseous fuels. The use of GTIs to burn hydrogen as part of the development of hydrogen energy technology is currently of particular interest. In order to assess the prospects of using GTIs in such a way, it is necessary, among other things, to understand the carbon footprint of the gas turbine as part of the carbon footprint of the entire life cycle of hydrogen. The article provides an overview of the results of previously published studies on life cycle assessment (LCA) of technically complex devices associated with the production and consumption of fuel and energy, which, from the point of view of the complexity of LCA, are most similar to gas turbine installation. The characteristics of the considered stages and resources used in the assessment of the stages of the life cycle of technically complex equipment are presented, including an analysis of the amount of materials used in production and construction. Taking into account its specific application in Russia, an assessment of greenhouse gas emissions at the stages of the GTI life cycle per MWh of produced capacity was carried out.

The global construction sector contributes a significant share of total greenhouse gas (GHG) emissions. In Australia, infrastructure activity alone generates 18% of the GHG emissions budget. The use of low-embodied carbon building materials is crucial to achieving sustainability in the construction sector and to fulfill national and international climate goals. Industrial hemp (Cannabis sativa L.) is considered a promising feedstock for sustainable construction materials because of its biogenic carbon content, fast-growing cycles with low agricultural input requirements, and technical functionality which is comparable to traditional materials. This study has applied the life cycle assessment (LCA) guideline of ISO 14040:2006 to estimate the carbon footprint (CF) expressed in carbon dioxide equivalent (CO2eq) emissions of hemp-based building materials in Western Australia. The functional unit is 1 m2 of hemp-based board, and the system boundary includes cradle-to-gate stages, i.e., pre-farm, on-farm, and post-farm activities. The production of 1 m2 of hemp-based board is estimated to be - 2.302 kgCO2eq. Electricity from the public grid for lignin extraction during the post-farm stage is the main contributor to total CO2eq emissions (26%), followed by urea production (14%) during the pre-farm stage. Overall, the use of electricity from the SWIS during the post-farm stage accounts for 45% of total emissions. Sensitivity analysis shows that the CF of hemp-based boards is highly sensitive to the source of energy, i.e., total replacement of the SWIS by solar power decreases the CF from - 2.30 to -6.07 kgCO2eq (164%). The results suggest that hemp-based boards exhibit lower embodied GHG emissions compared to traditional materials, such as gypsum plasterboards.

Life Cycle Assessment (LCA) is a widely recognized tool used to evaluate environmental impacts of a product or process, based on the environmental inventory database and bills of material. Data quality is one of the most significant factors affecting the analysis results. However, currently most datasets in inventory databases are generic i.e., they may represent material and energy flow of a process at market average, instead of a specific process used by a manufacturer. As a result, stockholders are unable to track their supply chain to find out the actual environmental impact from each supplier and to compare the environmental performance of alternative options. In this paper, we developed a new framework i.e., blockchain based LCA (BC-LCA), where block-chain technology is adapted to secure and transmit inventory data from upstream suppliers to downstream manufacturers. With BC-LCA, more specific data can be acquired along the supply chain in a real-time manner. Moreover, the availability, accuracy, privacy, and automatic update of inventory data can be improved. A case study is provided based on an industrial supply chain, to demonstrate the utilization of BC-LCA.

Life cycle assessment (LCA) is used frequently as a decision support tool for evaluating different design choices of products based on their environmental impacts. A life cycle usually comprises several phases of varying timespan. The amount of emissions generated from different life cycle phases of a product could be significantly different from one another. In conventional LCA, the emissions generated from the life cycle phases of a product are aggregated at the inventory analysis stage, which is then used as an input for life cycle impact assessment. However, when the emissions are aggregated, the temporal variability of inventory data is ignored, which may result in inaccurate environmental impact assessment. Besides, the conventional LCA does not consider the environmental impact of circular products with multiple use cycles. It poses difficulties in identifying the hotspots of emission-intensive activities with the potential to mislead conclusions and implications for both practice and policy. To address this issue and to analyse the embedded temporal variations in inventory data in a CE context, the paper proposes to calculate the emission intensity for each life cycle phase. It is argued that calculating and comparing emission intensity, based on the timespan and amount of emissions for individual life cycle phases, at the inventory analysis stage of LCA offers a complementary approach to the traditional aggregate emission-based LCA approach. In a circular scenario, it helps to identify significant issues during different life cycle phases and the relevant environmental performance improvement opportunities through product, business model and supply chain design.

Agriculture is an important sector of European Union in societal , economic and environmental dimensions. Sustainability of the sector require improvements in its key operations. Weeding is one of the crucial operation having impact on farms’ productivity, safety for farmers, food security and environmental state. To achieve EU policy goals of sustainable agriculture there are needed new technical and organizational solutions. One of the advanced techniques are laser based weeding technique. It is important to understand well the impacts of introduction of these tech-niques to the markets and agricultural practice in sustainability context. For that reason Social Life Cycle Assessment was performed. The method was based on participatory approach. The as-sessment was carried in three perspectives: general society, farmers, and business perspective re-lated to agriculture. Expert interviews based on questionnaires and workshops were realized to get the opinions on the impacts of a new laser technique on particular aspects of its implementation. The results show generally positive impact in all perspectives, especially in the perspective of farmers.

Contemporary architects and the construction industry are trying to cope with increasing requirements concerning energy efficiency and environmental impact. One of the available options is the active utilization of energy gains from the environment, specifically solar energy gains. These gains can be utilized by, for example, solar walls and facades. The solar façade concept has been under development for more than a century. However, it hasn’t achieved widespread use for various reasons. Rather recently the concept was enhanced by the application of transparent insulation materials that have the potential to increase the efficiency of such façades. The presented study evaluates the environmental efficiency of 10 solar façade assemblies in the mild climate of the Czech Republic, Central Europe. The evaluated façade assemblies combine the principles of a solar wall with transparent insulation based on honeycomb and polycarbonate panels. The study applies Life-Cycle Assessment methodology to the calculation of environmental impacts related to the life cycle of the evaluated assemblies. The results indicate that even though there are several limiting factors, façade assemblies with transparent insulation have lower environmental impacts compared to a reference assembly with standard thermal insulation. The highest achieved difference is approx. 84% (in favour of the assembly with transparent insulation) during a modelled 50-year façade assembly service life.

Talking about sustainable development refers mainly to the environmental sphere, but the concept is much broader and also takes into account the social and economic conditions. The concept of sustainability, in this sense, is linked to the compatibility between the development of economic activities, the related social phenomena, and the protection of the environment. Therefore, the ability to balance social, economic and environmental sustainability is the very meaning of the concept of sustainable development. Firms that choose to develop policies and strategies to enhance and pursue sustainable development in the medium to long term have the burden of having to quantitatively document the improvements in production processes with the aim of sustainable development. As a result, one of the biggest challenges for European industry is to introduce sustainability principles into business models leading to competitive advantage. This is particularly important in raw material and energy intensive manufacturing sectors such as the ceramic industry. The present state of knowledge lacks a comprehensive operational tool for industry to support decision-making processes geared towards sustainability. In the ceramic sector, the economic and social dimensions of the product and processes have not yet been given sufficient importance. Moreover, the traditional research on industrial districts lacks an analysis of the relations between firms and the territory with a view to sustainability. Finally, the attention of scholars in the field of economic and social sustainability, has not yet turned to the analysis of the Sassuolo district. Therefore, in this paper we introduce the Life Cycle Sustainability Assessment (LCSA), as a method that can be a suitable tool to fill this gap, because through a mathematical model it is possible to obtain the information useful for decision makers to integrate the principles of sustainability both at the microeconomic level in enterprises, and at the meso-economic level for the definition of economic policies and territorial governance. Environmental and socio-economic analysis was performed from the extraction of raw materials to the packaging of the product on different product categories manufactured by the Italian ceramic industries of the Sassuolo district (northern Italy). For the first time the LCSA model, usually applied to unitary processes, is extended to the economic and industrial activities of the entire district, extending the prospect of investigation from the enterprise and its value chain to the integrated network of district enterprises.

Keywords: Biomass pyrolysis, Chemical Looping Combustion, Life Cycle Assessment, Environmental Impacts, Carbon Footprint.

The response of building elements during earthquakes has been an area of concern for different researchers around the world. The NSEs are the first elements to attain failure, the buildings after damages in safety priority are classified as in “Life Safety” mode, but in reality, they are in “Collapse Safety” mode and the occupants inside the buildings are in a state of “Non-Life Safety” as a result of falling of the hazardous NSE’s like cladding's, partitions, hanging objects. In addition to the Life Cycle Cost Assessment (LCCA), the Social Life Cycle Assessment (SLCA) is overlooked by the majority of the researchers, the community must be prepared to respond to an event more efficiently without any major casualties or loss of life. It is expected that by the end of 2050, almost double the construction will take place, the embodied energy during the pre-construction, post-construction and demolition generates a lot of CO2s into the environment, hence sustainability should be given due importance, helping in the achievement of Sustainable Developmental Goals (SDGs).

CONTEXT– Energy is widely involved in human activity and corresponding emissions of SOX, NOX and CO2 from energy generation processes affect global climate change. Clean fuels are desired by society because of their reduced greenhouse gas emissions. Hydrogen is once such candidate fuel. Much hydrogen is produced from fossil fuel, with biomass being an alternative process. OBJECTIVE– The project compared the environmental impact of hydrogen production by natural gas steam reforming vs. biomass gasification. METHOD–Environmental impact was calculated from the input and output data from life cycle inventory analysis. The impact assessment was focused on greenhouse gas emission, acidification, and eutrophication. Models of the two processes were developed and analysed in OpenLCA. The agribalyse database was used to connect inventory flow data to environmental impacts. FINDINGS– For all three metrics, biomass gasification had lower impacts than natural gas steam reforming, sometimes by large margins. For biomass gasification the silica sand production contributes most to all three impact categories, whereas for natural gas steam reforming it is the LPG extraction.

Main purposes and research question: Wheat is the second largest grain crop by tonnage in the world and the largest in Denmark. Given the observed, adverse impacts on wheat yields of climate change and the importance of wheat in the human diet, the purpose of this study was to use life cycle assessment to compare conventional wheat farming with indoor vertical farming using hydroponics. Methods: Life Cycle Assessment was used to assess the base case systems up to the “farm gate” for 1 tonne of wheat grain. The processes contributing most of the impacts were identified, and scenarios were assessed to determine how much the impacts could be reduced. Results: The conventional system outperformed the base case vertical system in every impact category, due to the electricity consumption in the lighting system. The scenarios included increasing the efficiency of the LED lighting and using 100% wind energy, but the conventional system still outperformed the vertical system by significant margins in all impact categories. This was due to the low photosynthetic conversion efficiency and the high energy density of wheat. Conclusions: Until significant improvements are made to lighting efficiency, the photosynthesis conversion efficiency of wheat, new wheat variants designed for vertical gardens and the sustainability of electricity supply, conventional wheat production will be environmentally preferable and vertical gardens would be advised to focus on food products with low energy densities.

Building carbon footprint analysis is a key instrument for assessing the impact of different constructions on climate change. Several standards and methodologies are available to calculate the footprint of buildings, including standards and norms, life cycle assessment (LCA), and dedicated software tools. The use of BIM software for these calculations is both scientifically justified and very practical. This scientific publication focusses on the application of a BIM-based research methodology for the analysis of the carbon footprint of a single-family house. The research process included the following steps: (i) design of a single-family house with timber frame construction using Archicad BIM software, (ii) simulation of the building energy performance using the EcoDesigner Star plug-in, (iii) life cycle assessment (LCA) using the plug-in for Archicad, (iv) preparation of a second model with traditional masonry construction for comparison, and (v) comparative analysis of the single-family house models with timber frame and masonry construction. Analysis of the results highlights significant differences in CO2e emissions between masonry and timber buildings and the varying impact of individual elements on the total CO2e emissions of the buildings studied. These findings are relevant for future work on sustainable building design and construction, which aims to minimise negative environmental impacts. The goal of minimising the cumulative carbon footprint of buildings is critical to achieving the Sustainable Development Goals and combating climate change.

Purpose – The paper aims to view how researchers have operationalized social impact assessment for construction projects over the last ten years. Design/methodology/approach – A systematic review was used to investigate case studies in the Social Life-Cycle Assessment (S-LCA) to analyze the application of the methodology. A qualitative study of 19 articles published between 2012 and 2022 was used to collect content on multiple categories impeding S-LCA through case studies in the construction industry. Findings – Our results showed the existence of limitations on the qualitative and quantitative aspects in measuring the social indicators. They were associated with the scoring method and the lack of data in some articles. Social implications – From this review, we understood that S-LCA has flaws in terms of the quality of the measurement, scoring method, and the lack of social data. Lack of social data means social impacts are being neglected and not assessed properly since there are several challenges pointed out throughout literature Originality/value – The originality of this research is that it focuses on case studies in the construction industry. It studies the operationalization of the S-LCA in this specific industry showing the different characteristics and challenges in the last 10 years.

Considering the manufacturing of automotive components, there exists a dilemma around the substitution of traditional Cast Iron (CI) with lighter metals. Nowadays, aluminium alloys, being lighter compared to traditional materials, are considered as a more environmentally friendly solution. However, the energy required for the extraction of the primary materials and manufacturing of components is usually not taken into account in this debate. In this study, an extensive literature review has been performed to estimate the overall energy required for the manufacturing of an engine cylinder block using (a) cast iron and (b) aluminium alloys. Moreover, data from over 100 automotive companies, ranging from mining companies to consultancy firms, have been collected in order to support the soundness of this investigation. The environmental impact of the manufacturing of engine blocks made of these materials is presented with respect to the energy burden; the “cradle-to-grave approach” has been implemented to take into account the energy input of each stage of the component lifecycle starting from the resource extraction and reaching to the end-of-life processing stage. Our results indicate that although aluminium components contribute towards reduced fuel consumption during their use phase, the vehicle distance needed to be covered in order to compensate for the up-front energy consumption related to the primary material production and manufacturing phases is very high. Thus, the substitution of traditional materials with lightweight ones in the automotive industry should be very thoughtfully evaluated.

Qualtra, an innovative 10 MW geothermal power plant proposal, employs a closed-loop design to mitigate emissions, ensuring no direct release into the atmosphere. A thorough assessment utilizing energy and exergy analysis, Life Cycle Assessment (LCA), Exergo-economic and Exergo Environmental Analysis (EevA) was conducted. The LCA results, utilizing the ReCiPe 2016 midpoint methodology, encompass all the spectrum of environmental indicators provided. The technology implemented makes it possible to totally avoid direct atmospheric emissions from the Qualtra plant, so the environmental impact is mainly due to indirect emissions over the life cycle. The results obtained for the Global Warming Potential indicator is about 6.6 g CO2/kWh, notably lower compared to other conventional systems. Contribution analysis reveals that the construction phase dominates, accounting for over 90% of the impact in all LCA MidPoint categories. At the component level, a single score calculation incorporating normalization and weighting was executed. The resulting single score is then used into Exergo-Environmental Analysis (EEvA), highlighting the well system as the most impactful contributor, constituting approximately 45% of the total impact. Other substantial contributions to the environmental impact include the condenser (21%), the turbine (17%), and the HEGeo (14%). The Exergo-Economic analysis assesses cost distribution across major plant components, projecting an electricity cost of about 8.3 c€/kWh.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

Since the energy sector is the main source of greenhouse gases, it has the highest potential for improvement. Improvements can be achieved by generating energy from renewable sources. Combined with thermal energy storage, concentrating solar power plants represent a promising technology for dispatchable renewable energy, ensuring a stable energy supply even in remote areas without contributing to greenhouse gas emissions during operation. However, it is important to note that greenhouse gases and other polluting emissions may occur during the manufacturing process of concentrating solar power plant components. This work analyses the design of the receiver to produce thermal energy for the existing solar dish CSP plant at the Energy Center of the Politecnico di Torino. The objective of this plant is to produce hot water for a small case study. Considering the average solar irradiance for Turin equal to 800 W/m2, the surface heat flux was obtained from the first part of the analysis, which was used to obtain the maximum internal temperature in the receiver equal to 873.7 °C. The maximum temperature obtained was a constraint for the selection of the material for the solar receiver. Of the various possibilities, copper was chosen. In the second part of the work, a Life Cycle Assessment was carried out to compare the emissions generated during the production of the main components of the CSP plant with the emissions generated by the methane-fuelled water heater that produces the same amount of water as the CSP plant. It can be concluded that the manufacture of the main components of the CSP plant results in lower greenhouse gas emissions than the operational phase of a conventional natural gas-fired water heater (1.6 kg CO2/day).

The civil construction industry is one of the sectors that most consume natural resources in the world and, consequently, one of that generate more waste. Thinking about constructive techniques that generate less impact on the environment is vital to ensure sustainable development. In this scenario, the Life Cycle Assessment (LCA) has been presented as an internationally recognized approach, that assesses the potential impact of products and services on human health and the environment, throughout its entire life cycle. Aimed to identify construction techniques and vertical closing systems that generate less impact and consumption of natural resources, the impacts generated by the life cycle of the three vertical closing systems most applied in construction sites in Brazil were compared: ceramic brick masonry system (CBr); concrete block masonry system (CBk); and structural blocks masonry system (SBk). The SBk proved to be the least impacting to the “Resource Scarcity”, “Damage to Human Health”, and “Damage to the diversity of Ecosystems” interesting areas. This performance is directly related to the use of cement CPIII type and also by the fact that the SBk consumes less concrete and mortar than the others. Already the "Water Consumption" area, the CBk was the least impacting due to the lower consumption of electricity during its life cycle. The reliability of the results was proven through a sensitivity analysis of the normalization and characterization factors, which consisted of comparing the results obtained by applying two different methodologies. It is believed that the LCA study carried out can assist in the decision-making process regarding the choice of the most sustainable construction method.

As the world attempts to decarbonise the food industry and limit greenhouse gas (GHG) emissions, plant-based meat analogues (PBMAs) have emerged as a sustainable alternative to traditional meat. This study implemented a life cycle assessment (LCA) to rigorously compare the environmental impacts of a beef burger (BB), produced with British beef, against a meat analogue (MA) equivalent with a publicly available recipe. For the LCA, a cradle-to-fork system boundary was utilised, alongside a functional unit of a single 100 g burger patty. Results from the LCA revealed that the BB patty had more than double the total environmental impact than the MA equivalent, as well as possessing a global warming impact that was 62% higher. A simple extrapolation illustrated that if the UK population switched from beef to meat analogue patties, 3 million tonnes of CO2e could be saved annually, corresponding to 0.74% of the country’s yearly territorial GHG emissions. Scenario analyses displayed how the environmental impact of the MA patty remained stable regardless of changes in exportation, ingredient origin or soy protein sourcing. Moreover, sensitivity analysis conducted with an alternative characterisation method corroborated initial findings, whilst uncertainty analysis ensured that nearly all conclusions generated from the original comparison were robust. Future studies should conduct peer-reviewed LCAs on PBMA patties with commercial recipes based on other plant-based proteins, as well as fully understanding any potential health implications of long-term PBMA consumption.

Construction project management and cost management is a difficult process that affects the overall success of construction projects. The success of a construction project can be assessed according to key performance indicators (KPIs). Cost savings and cost optimization over the life of a construction project is one of these KPIs. Cost management is largely performed through intelligent information technology in the construction industry. Information systems and information technologies have seen an increase in use in the management of construction projects. The same goes for cost management. Several studies mentioned in the paper point to this increase in use in recent years also in the management of costs at various stages. Many studies point to the use of information technology and software applications in the field of cost management. Still, to a large extent, there are no surveys focused on the analysis of the impact and impact factor of information technology on cost savings or cost optimization in various phases of construction projects. The research discusses the issue of the impact of information technology on cost management in various phases of a construction project. The main goal of the research is to analyze the influence of information technology factors on cost savings and optimization in individual phases of a construction project. Several statistical methods were used in the research. The resulting model of information technology impact factor was created based on data processing and the use of the AHP method.

Nowadays, consumers have growing expectations for healthier and higher-quality food, and sustainable food choices are also taking on an increasingly central role. This paper assesses the environmental loads and energy resources of vegan, semi-vegetarian, and traditional restaurant soups and main dishes, focusing on preparation and cooking phases based on the life cycle assessment. The optimal menu samples were selected based on statistical methods. Mann-Whitney and Krus-kal-Wallis tests were applied to investigate restaurant products' distribution and carbon footprint. Based on the results, the preparation phases have a more significant impact. The environmental loads for the life cycle of vegan and semi-vegetarian menus are lower. Furthermore, a sustainability assessment model was developed by integrating lean and life cycle assessment approaches called "GreenCycLEAN." Research results are helpful for the sustainability of catering establishments.

The purpose of this paper was to analyze the development trend of hazardous chemical packaging towards low carbon economy from both qualitative and quantitative perspectives. Four types of relatively small volume packaging with volume/weight less than 450L/400kg, respectively, and three intermediate bulk containers (IBCs), which are widely used for hazardous chemicals were studied to calculate the carbon footprint (CF) from cradle to grave using life cycle assessment (LCA) method and to predict the future carbon emission of hazardous chemical packaging in the next five years (2016-2020), based on the export data of Tianjin Port in China. Grey model (GM) was adopted in the prediction. The results showed that majority of IBCs have lower carbon footprint than other types when the packaging contained same amount of same hazardous chemical. With the development of international trading, the demand of hazardous chemicals will increase as well. As the result, carbon emission generated by hazardous chemical packaging will increase accordingly. However, based on GM simulation result, increasing the amount of IBC use will effectively reduce the relative amount of carbon emission.

Nutrient depletion in Tanzanian sisal production has led to yield decreases over time. We use nutrient mass balances embedded within a life cycle assessment to quantify the extent of nutrient depletion for different production systems, then used circular economy principles to identify potential cosubstrates from within the Tanzanian economy to anaerobically digest with sisal wastes. The biogas produced is then used to generate bioelectricity and the digestate residual can be used as a fertilizer to address the nutrient depletion. If no current beneficial use of the cosubstrate was assumed, then beef manure and marine fish processing waste were the best cosubstrates. If agricultural wastes were assumed to have a current beneficial use as fertilizer, then marine fish processing waste and human urine were the best cosubstrates. The largest reduction in environmental impacts resulted from bioelectricity replacing electricity from fossil fuels in the national electricity grid and improved onsite waste management practices. There is significant potential to revitalize Tanzanian sisal production by applying circular economy principles to sisal waste management and bioenergy production.

The transport sector in Germany causes one-quarter of energy-related greenhouse gas emissions. One potential solution to reduce these emissions is the use of battery electric vehicles. Although a number of life cycle assessments have been conducted for these vehicles, the influence of a transport system wide transition has not been researched sufficiently. Therefore, we developed a method which combines life cycle assessment with an agent-based transport simulation and synthetic electric, diesel and gasoline powered vehicle models. We use the transport simulation to obtain the number of vehicles, their lifetime mileage and road-specific consumption. Subsequently we analyze the product systems’ vehicle production, use phase and End-of-Life. The results are scaled depending on the covered distance, the vehicle weight and the consumption for the whole life cycle. The results indicate that the sole transition of drive trains is insufficient to significantly lower the greenhouse gas emissions. However, sensitivity analyses demonstrate that there is a considerable potential to reduce greenhouse gas emissions with higher shares of renewable energies, a different vehicle distribution and a higher lifetime mileage. The method facilitates the assessment of the ecological impacts of the complete car based transportation in urban agglomerations and is able to analyze different transport sectors.

China's implementation of public-private partnerships projects has been quite effective, involving infrastructure and other livelihood projects, a total of 19 industries, and an investment of nearly 1.5 trillion yuan. The characteristics of PPP projects such as long construction period and large investment amount determine the risks of PPP projects are also great, and the PPP projects of comprehensive environmental governance are also the same. The government and social capital use the PPP model to cooperate, and use the principal component analysis method to assess the risks of the entire life cycle of the comprehensive environmental governance PPP project. Therefore, it plays an important role in ensuring the smooth implementation of projects and reducing the losses caused by risks. According to the risk factors of the whole life cycle of the comprehensive environmental governance PPP project, an indicator system of 5 first-level indicators, 18 second-level indicators, and 43 third-level indicators has been established. Principal component analysis is used to analyze the influence weight of risk factors at each stage. The analysis shows that among the four stages, environmental pollution risk, project approval delay risk, completion risk, interest rate and financial fluctuation risk, and franchise life risk are the most influential risks in the implementation of PPP projects. Therefore, suggestions are made through the risk factors of each stage in the comprehensive environmental governance PPP project. For example, strengthen the response to the external environment risks of the comprehensive environmental governance PPP project, standardize the bidding and procurement of the comprehensive environmental governance PPP project, and strengthen the subsequent management of the transfer of the comprehensive environmental governance PPP project. In this way, the ability to resist risks of comprehensive environmental governance PPP projects is improved; the smooth implementation of the project is guaranteed, and the long-term development of comprehensive environmental governance PPP projects is promoted.

The construction industry is responsible for 40 to 45% of primary energy consumption in Europe alone. Therefore, it is essential to find new materials with a lower environmental impact in order to attain sustainable housing. This study aims to determine and compare the environmental impact of two clay samples forming a basis for the manufacture of traditional brick, a standard material in building construction; traditional red clay brick and a brick based on clay mixed with a biological ingredient. The samples of fired clay were manufactured at the laboratory scale, the results being valid exclusively as indicators for the extrapolation of the analysis to other studies. The results of the environmental impact of these formulations have been examined through an evaluation of life-cycle analysis (LCA), observing that the incorporation of biological pore forming agents led to a decrease of around 15 to 20% of all impact categories studied. Thus, the suitability of using biological-based additives in clay bricks was confirmed both for their constructive characteristics (lighter material) and increased energy efficiency (better thermal insulation) considering the environmental point of view.

Wind technology is considered to be among the most promising types of renewable energy sources, and due to high oil prices and growing concerns about climate change and energy security, it has been the subject of extensive considerations in recent years, including questions related to the relative sustainability of electricity production when the manufacturing, assembly, transportation and dismantling processes of these facilities are taken into account. The present article evaluates the environmental impacts, carbon emissions and water consumption, derived from the production of electric energy of the Villonaco wind farm, located in Loja-Ecuador, during its entire life cycle, using the Life Cycle Analysis method. Finally, it is concluded that wind energy has greater environmental advantages, since it has lower values of carbon and water footprints than other energy sources. Additionally, with the techniques Cumulative Energy Demand and Energy Return on Investment, sustainability in the production of electricity from wind power in Ecuador is demonstrated; and, that due to issues of vulnerability to climate change, the diversification of its energy mix is essential considering the inclusion of non-conventional renewable sources such as solar or wind, this being the only way to reduce both the carbon footprint and the water supply power.

The publication presents the assessment of the influence of surface treatment such as shot-peening on the fatigue life of a compressor blade exposed to resonant vibrations. As part of the work, a geometric model of the blade was developed and a numerical modal and fatigue analysis were performed. The fatigue analysis was based on the Manson-Coffin-Basquin and Ramberg-Osgood models. As part of the work, the influence of different values of residual stresses on the results of fatigue life was determined. Additionally, the location of the highest equivalent stresses was established. The obtained results of the numerical analyzes were compared with the results presented in the scientific literature. An additional aim of the study was to determine the size of the grains at various points of the blade as well as the thickness of the layer plasticized as a result of peening. The obtained results are presented in the form of tables and charts. The relationship between the location of the highest values of equivalent stresses and the thickness of the plasticized layer was determined. The explanation of the effect of shot peening on the increase in fatigue life of the blade was proposed.

In this paper we analyze the relationship between bankruptcy risk and the corporate life cycle in Pakistan from 2005 to 2014. For this purpose, we run a Hierarchical Linear Mixed Model (HLM) for a sample of 301 non-financial listed firms in 12 different sectors. The empirical outcomes reveal that firms during introduction, growth and, decline stages (mature stage) of life-cycle experience higher (lower) bankruptcy risk. Moreover, in juxtaposition with growth stage, bankruptcy risk is higher at the introduction stage of life-cycle. These findings suggest that financial managers should be cautious about the financial fragility of the firm at each stage of corporate life-cycle. The results also entail that Pakistani firms do not follow a sequential pattern in their life-cycle rather they have the tendency to revert to a previous stage or jump to the next stage of life-cycle. This is the first study that empirically examines the association between firm life-cycle stage and corresponding bankruptcy risk and asserts that managers must incorporate the life-cycle effects into their financial planning and decision making for sustainable working of an enterprise.

This study explores the pivotal biofilm life cycle, essential for comprehending intricate processes in biofilm formation and dispersal. With profound implications for medicine, environmental science, and industrial applications, the life cycle involves initial attachment, irreversible attachment, maturation, and dispersion. Employing bibliographic analysis, the paper unravels critical aspects, unveiling key keywords, prominent research countries/regions, and significant research organizations. This comprehensive approach provides insights into the current biofilm research landscape, identifying gaps for future exploration. Biofilm's influence extends to medical conditions, environmental ecosystems, and industrial challenges, accentuating the urgency of understanding its life cycle. The study also delves into global research distribution and influential organizations, guiding collaborative efforts. As a forward-looking initiative, it proposes future research opportunities, aiming to steer advancements and address challenges in biofilm science. Ultimately, this analysis contributes to the ongoing progress of biofilm research, fostering interdisciplinary collaboration and inspiring future initiatives.

Flax fiber appears as a suitable feedstock in the endeavor of deploying a sustainable biobased economy. Its environmental performance as reinforcement in composite materials has been studied in previous Life Cycle Assessments (LCAs). However, these studies only present a coarse Life cycle Inventory (LCI) and often fail to detail all processes of the supply chain or to represent the co-products. This paper aims to bridge this gap and provide data for future LCAs on flax fiber production and transformation.The study focuses on the impacts of producing a bio-based reinforcement material (a fabric product for non-aesthetic purposes) with a system expansion perspective. The functional unit is defined as the production of 2400 m² flax-based technical textile per year, this corresponds to one hectare of cultivated land. The geographical scope considers that the production occurs in France and that some manufacturing process are outsourced in China. A Sensitivity Analysis was carried out to assess the influence of the electricity mix in the various countries involved in the manufacturing cycle.A detailed life cycle inventory for flax fiber production and transformation was built and the environmental performance of a flax technical textile was assessed as a cradle-to-gate LCA. The fate of co-products was documented and was shown to contribute to the reduction of the generated environmental impacts. Through a cradle-to-gate LCA, a broader understanding of the environmental performance of a flax-based technical textile was presented by including the valorization of co-products and a wider set of analyzed impact categories, going therefore beyond the existing state-of-the-art. Results show agricultural activities and electricity production to be the biggest contributors to the environmental impacts of flax technical textile; contributions due to land use changes were minor in comparison. Very specifically for this case study, a sensibility analysis showed the influence of an all-French production to be more efficient from an environmental point of view.

Typhulaceae Jülich is one of the cold-adapted fungal families in basidiomycetes. Typhula (Pers.) Fr. and Pistillaria Fr. representing the family are distinguished from the morphology of a stipe to a hymenium (Fries 1821). The hymenium of Typhula is distinguishable from the stipe, but indistinguishable and consecutive in the genus Pistillaria. This taxonomic criterion is ambiguous, and consequently the opinion of Karsten (1882) has been widely accepted; I the genus Typhula, basidiomata develop from sclerotia, while basidiomata develop directly from substrata in the genus Pistillaris. But, Corner (1970) observed basidiomata of Pistillaria petasitis S. Imai in Hokkaido, Japan, from sclerotia. We collected irregular sclerotia of Typhula hyperborea H. Ekstr. from Upernavik, West Greenland. This specimen had a stipe-like structure on a Poaceae plant, and sclerotia developed on its tip. In August, P. petasitis in Hokkaido, Japan, formed basidiomata directly from substrates on the ground. Similar phenomena were found from other Typhula spp. in Japan. All of these fungi had the potential to produce sclerotia in culture, and as well as the capacity of mycelial growth at ambient air temperatures in each locality when samples were collected. These findings suggest that Typhula spp. developed basidiomata not only from the sclerotia dispersed by the basidiospores but also mycelia generated by the spore germination formed basidiomata multiple times depending on their growth environments.

Modern experimental astroparticle physics features large-scale setups measuring different messengers, namely high-energy particles generated by cosmic accelerators (e.g. supernova remnants, active galactic nuclei, etc): cosmic and gamma rays, neutrinos and recently discovered gravitational waves. Ongoing and future experiments are distributed over the Earth including ground, underground/underwater setups as well as balloon payloads and spacecrafts. The data acquired by these experiments have different formats, storage concepts and publication policies. Such differences are a crucial issue in the era of big data and of multi-messenger analysis strategies in astroparticle physics. We propose a service ASTROPARTICLE.ONLINE in the frame of which we develop an open science system which enables to publish, store, search, select and analyse astroparticle physics data. The cosmic-ray experiments KASCADE-Grande and TAIGA were chosen as pilot experiments to be included in this framework. In the first step of our initiative we will develop and test the following components of the full data life cycle concept: (i) describing, storing and reusing of astroparticle data; (ii) software for performing multi-experiment and multi-messenger analyses like deep-learning methods; (iii) outreach including example applications and tutorial for students and scientists outside the specific research field. In the present paper we describe the concepts of our initiative, and in particular the plans toward a common, federated astroparticle data storage.

Reassessment of the fatigue life for wind turbines structural components is typically performed using deterministic methods with the same partial safety factors as used for the original design. However, in relation to life extension, the conditions are generally different from the assumptions used for calibration of partial safety factors; and using a deterministic assessment method with these partial safety factors might not lead to optimal decisions. In this paper, the deterministic assessment method is compared to probabilistic and risk-based approaches, and the economic feasibility is assessed for a case wind farm. Using the models also used for calibration of partial safety factors in IEC61400-1 ed. 4 it is found that the probabilistic assessment generally leads to longer additional fatigue life than the deterministic assessment method. The longer duration of the extended life can make life extension feasible in more situations. The risk-based model is applied to include the risk of failure directly in the economic feasibility assessment and it is found that the reliability can be much lower than the target for new turbines, without compromising the economic feasibility.

The wastewater circular economy (WW-CE) promises a solution to improve water and sanitation management worldwide. However, the transition from conventional to circular wastewater treatment plants (WWTPs) requires facilitation to aid in decision makers understanding of integral sustainability impacts of alternative WW-CE configurations. This research implemented Life Cycle Sustainability Assessment (LCSA), combining Life Cycle Assessment, Social Life Cycle Assessment and Life Cycle Costing with a Multi-criteria Decision Making (MCDM) model to quantify environmental, socio-cultural, and economic impacts of conventional WWTPs with the WW-CE. Two real WWTPs in Chile have embraced the WW-CEs and adopting the title of Biofactories. These were considered as case studies, compared under three scenarios to demonstrate the sustainability trade-offs of the transition from no sanitation to conventional WWTPs and Biofactory WW-CE configurations. Results demonstrated that the transition to WW-CEs improved integral sustainability according to the LCSA model implemented in both WWPTs. This study highlights the urgent need to adopt sustainable decision-making models to not only improve sanitation coverage, but also improve sustainability performance of the sanitation industry across the globe.

Today, the digital economy has pursued the required social and economic development, and enterprises can achieve long-term sustainability by relying on the digital platform ecosystem. However, the development of the digital economy and the rapid growth of platform ecosystems have also generated some problems. To study effective digital platform ecosystem governance, this study used the tripartite evolutionary game method and analyzed the changes and effects of platform regulation under different development stages from the perspectives of government, platforms, and enterprises. The results indicate that in the early stages, digital platforms primarily relied on the government’s obligation to regulate. With the digital platform ecosystem’s evolution, the platform organization and settled enterprises’ governance effects gradually appeared, establishing the three common constraints of governance mode. Finally, when the digital platform ecosystem is in its self-renewal period, the government effect is reduced, with the platform itself and settled enterprises taking primary supervisory roles. This study provides reasonable methods for effective platform governance at different stages and enriches the theoretical basis and management practices of platform ecosystems.

Energy storage systems (ESSs) are the key elements to improve the operation of power systems. On the other hand, these elements challenge the power system planners. The difficulties arise as a result of the ESSs' economic and technological features. The cycle life of ESSs is a critical aspect that influences the choices made during expansion planning processes. In this manuscript, we have focused on a new model for the expansion planning of ESSs considering the impacts of technical properties, such as the cycle life and depth of discharge. For this purpose, the proposed model consists of the hourly operation planning of ESSs in the sample days of year. A new indicator is proposed to determine the daily charging/discharging cycles of ESSs. Numerical results show the ability of the proposed model to determine the optimal technology and capacity of ESSs.

Having as objective to reach a circular economy, it is important to maximize the Physical Asset’s Life Cycle. The evaluation of Physical Assets Life Cycle may have several approaches which may provide different results. These differences may not be very significant, but must be taken into consideration, because they have consequences in the manager decision. This permits to have a wider time interval to decide when to withdrawal the Physical Asset or to renewal it, and or if this ought to continue functioning because the profits are higher than the expenses, what allows to diminish waste and increase sustainability. These are some aspects that are discussed in this paper, which presents several models to evaluate the Physical Assets Life Cycle, considering the market value, devaluations methods and a more generalized way of Fisher’s Equation, which can include the Risk tax, among others. The results are discussed supported in data for simulation, which are used for each Econometric Model aiming to evaluate the differences among them. In all Models they are considered not only the expenses, namely of Investment and Functioning, but also the Profits, which permit to evaluate the Physical Asset Life Cycle in a holistic way. The models are very versatile, allowing to evaluate quantitatively the changing in the maintenance policies, the energy prices variations, the risk evaluation, the variation of profits according to the real market, and so on. The results demonstrated the robustness of the approach described and that maximize the Physical Assets Life Cycle allowing to minimize the consumption of world resources and, by consequence, it contributes for a more sustainable world.

Purpose Prospective life cycle assessment (pLCA) is a key method for providing environmental decision support for future technologies. The specific technology under study is often modeled by the practitioner (the so-called foreground system), whereas data for supply chains are sourced from life cycle inventory databases (the so-called background system). Within pLCA, it is paramount to consider possible future developments for both foreground and background systems to avoid a temporal mismatch between the specific technology under study and the wider economy, which could lead to incorrect conclusions. Therefore, and given the importance of future-oriented environmental decision support, efforts to develop prospective life cycle inventory (pLCI) databases have recently increased. However, there is still much to be improved to realize the widespread use of these databases and to have a stronger real-world effect on how future technology is designed. Methods This paper summarizes recent developments and structures the information chain behind pLCI databases. We then discuss conditions for the broad application of pLCI databases, and we propose priorities and ways forward to overcome existing challenges to foster the use of pLCI databases. Results The conditions are scientific integrity, usefulness to LCA practitioners, accessibility, usability, interpretability, and a continuous improvement process in which core stakeholders coordinate efforts to streamline the generation, sharing, and use of pLCI databases. Conclusions Priority should be given to installing a continuous process to improve the coverage and consistency of pLCI databases, to improve related guidance and documentation, and to remove practical barriers relating to the access and usability of pLCI databases in LCA software.

The framework of product life cycle (PLC) cost analysis is one of the most important evaluation tools for a contemporary high-tech company in an increasingly competitive market environment. The PLC-purchasing strategy provides the framework for a procurement plan and examines the sourcing strategy of a firm. The marketing literature emphasizes that ongoing technological change and shortened life cycles are important elements in commercial organizations. From a strategic viewpoint, the vendor has an important position between supplier, buyer and manufacturer. The buyer seeks to procure the products from a set of vendors to take advantage of economies of scale and to exploit opportunities for strategic relationships. However, previous studies have seldom considered vendor selection (VS) based on PLC cost (VSPLCC) analysis. The purpose of this paper is to solve the VSPLCC problems considering the situation of a single-buyer-multiple-supplier. For this issue, a new VSPLCC procurement model and solution procedure are derived by this paper to minimize net cost, rejection rate, late delivery and PLC cost subject to vendor capacities and budget constraints. Moreover, a real case in Taiwan is provided to show how to solve the VSPLCC procurement problem.

For a long time, a company's Product Development Process (PDP) was seen as supporting the operations department, although PDP decisions and mistakes have a considerable impact on market performance. This is critical even in agriculture where bad habits and practices in the PDP can lead rural producers to great losses. Therefore, this research investigated the effect on the market performance of rural products (banana) in the southern region of Brazil, based on two analyses: (i) how sustainability practices support the PDP phases and (ii) how the phases of the Product Life Cycle Assessment (LCA) mediate sustainability practices and PDP phases. This study presents a quantitative analysis using Confirmatory Factor Analysis (CFA) and hierarchical ordinary least squares (OLS) regression of data obtained from a survey of 110 rural producers who directly participate in the banana production and planning process in southern Brazil. Our results shows that sustainability practices support the PDP, and we confirm that the product development and post-development phase has an effect on market performance. In addition, we identified that in the pre-development phase of the PDP, dealing with rural products (bananas), the maturity stage of the LCA mediates sustainability. In the PDP development phase, we concluded that rural families that develop economic and environmental practices with their products in the market growth phase may have reduced results. As for the post-development phase of the PDP, we conclude that when companies invest in environmental and social practices, there is a complete mediation of the effect, where these practices lose strength if the product is in the introduction and maturity phases in the market. As originality, our study contributed to demonstrate value on the product life cycle for the product development process in agriculture using sustainability practices through a systemic approach, filling the gap in the literature due to the lack of research on these areas seen in an integrated way.

This work aims at improving surface integrity and LCF life of machined Inconel 718. The correlation between the LCF life of Inconel 718 and various states of machined surface integrity is explored. In this paper, the surface integrity of Inconel 718 specimens is enhanced by low plasticity burnishing (LPB). The LCF life with different surface integrity specimens is predicted by micro-macro finite element method (FEM). Firstly, the LCF specimens with different surface integrity are machined by turning (turned specimen), polishing (matrix specimen) and LPB process (LPBed specimen). Secondly, the LCF experiment is carried out to reveal the effect of surface integrity on LCF life. Finally, the LCF micro-macro FEM model is proposed to predict the LCF of machined Inconel 718 specimens. The representative volume element (RVE) model is established based on the measured surface integrity and microstructure of Inconel 718 specimens. The effect of surface integrity on LCF life is transformed to equivalent load. The micro-macro FEM model combined with Tanaka-Mura dislocation crack initiation theory and extended finite element method (XFEM) is applied to predict the LCF life the machined specimens. The study results show that the LCF life of LPBed specimens can be improved by 90.5% and 36.1% compared with that of turned specimens and polished matrix specimens, respectively. The errors between FEM prediction results and experimental results are 13.1%, 9.2% and 12.2%, respectively. The proposed micro-macro FEM model could be utilized to predict the LCF life of Inconel 718 with different surface integrity, and further to apply the LCF life prediction in industry.

The study examines the relationship between corporate social responsibility (CSR) and the corporate life cycle (CLC) of the Chinese pharmaceutical listed companies for the duration of 2010 to 2018. The firm cash flow pattern is used as a proxy for the CLC. The study results indicate that the relationship between CSR and CLC is positive and linear in all the phases of the CLC including, the introduction, growth and maturity stage. Although the relationship is smaller and more significant at the maturity phase. The research further shows that investors incorporating social responsibilities values play a key role in the firm cash flow performance (CFP) across all the firm stages. Whilst, employees espousing social responsibility tenets can only improve CFP in the decline or shakeout stages. Likewise, embedding CSR into the customers group only improves CFP at the maturity stage. Applying the lag effects lead to the same study results. The finding for the bi-directional causality indicates that although CSR can positively influence CFP, CFP is ultimately more associated with the firm unobservable characteristics rather than performance attributed to CSR. On the whole, our study results point to positive causality between CSR and CFP across all the firm life stages and the CSR has a mediating effect on each life cycle.

Concrete condition assessing penetrometers need to be able to distinguish between making contact with a hard (concrete) surface as opposed to a semi-solid (corroded concrete) surface. If a hard surface is mistaken for a soft surface, concrete corrosion may be over-estimated, with the potential for triggering unnecessary remediation works. Unfortunately, the variably-angled surface of a concrete pipe can cause the tip of a force-sensing tactile penetrometer to slip and thus to make this mistake. We investigated whether different shaped tips of a cylindrical penetrometer were better than others at maintaining contact with concrete and not slipping. We designed a range of simple symmetric tip shapes, controlled by a single superellipse parameter. We performed a finite element analysis of these parametric models in SolidWorks before machining in stainless steel. We tested our penetrometer tips on a concrete paver cut to four angles at 20∘ increments. The results indicate that penetrometers with a squircle-shaped steel tip (a=b=1,n=4) have the least slip, in the context of concrete condition assessment.

Additive Manufacturing (AM) has been proving suitable to support or even replace traditional manufacturing in several industries, offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and greenhouse gas (GHG) emissions. This study aimed to carry out a comparative assessment of the life cycle, from gate to gate, in the production of a low alloy carbon steel flange part using ER-90 wire. The methods utilized were Wire and Arc Additive Manufacturing (WAAM) and conventional manufacturing (CM) by forging, and comparative factors were energy demands, GHG emissions and generated solid waste. The total energy consumption in WAAM was 10,239.40 MJ, total carbon footprint in CO2 equivalent (CO2e) was 714.1 kgCO2e kg-1, and generated solid waste was 68.6 kg, respectively, 90%, 95% and 76% lower than consumption calculated in conventional manufacturing.

The effects of environmental media on the corrosion fatigue fracture behavior of 25CrMo steel were investigated. The media include air, and a 3.5 wt.% and a 5.0 wt.% NaCl solutions. Experimental results indicate that the media induces the initiation of corrosion fatigue cracks at multiple sites. The multi-cracking sites cause the changes in the crack growth directions, the crack growth rate during the coupling action of the media and the stress amplitude. The coupling effects are important for engineering applications and research. The probability and predictions of the corrosion fatigue characteristic life can be estimated using the 3-parameter Weibull distribution function.

The Life Cycle Analysis (LCA) was used to assess the impact of biomethane plant of the “La Católica” in Pedregal-Majes-Arequipa farm, fed with cow manure and holding a production of 60 Nm3/day of purified biogas. Life cycle inventory, impact assessment and interpretation were performed. The functional unit established was 1 MJ of energy produced; the study was modeled with SimaPro software, Ecoinvent Database and ReCiPe Midpoint (H) impact assessment methodology, according to the impact categories of climate change and fossil resource depletion. The impact analysis was limited to the Well to Tank (WTT) approach, which involves feedstock transport, substrate mixed, anaerobic digestion, biogas purification, storage and injection of the fuel into transport vehicles. The digestion process generated the highest amount of CO2 emissions (1.79E-02 kg CO2 eq/MJ-biomethane) and the highest depletion of fossil resources (6.58E-03 kg oil eq/MJ-biomethane), compared to the other fuel production, due to energy consumption and transport infrastructure. Biomethane was then compared to fossil fuels, resulting in natural gas generating the least amount of CO2 emissions, followed by diesel and finally biomethane. For the fossil resource depletion category, biomethane presented the lowest amount of fossil fuel consumption (1.37E-02 kg oil eq/MJ-biomethane), followed by natural gas and diesel.

Coral recruitment is an important factor to coral reefs in maintaining their health. Currently, numerous coral reefs are facing extreme degradation, which protection and therefore rehabilitation practices are required to reverse. The present study explores the potential role of coral recruitment assessment by citizen scientists about the impacts of human influences towards coral reefs through measurement of coral recruitment values. Only a very small number of studies use forms of pre-launch assessment prior to reef restoration. These methods are able to properly guide vital decision-making information for reef rehabilitation methods and locations. In this initial study we observe significant relationships between reefs with higher coral recruitment values and their health. As compared to other average coral reef values, the reef we measured had higher recruitment values on average. Two sections of the reef had noticeably higher mean corals per square meter compared to average values, while a third section of the reef had a lower frequency. This section has been brought to concern through the pre-launch assessment, and has potential for rehabilitation through coral transplantation and a reduction of anthropogenic actions within the area.

A Life Cycle Analysis was performed considering three existing power plants of comparable size operating with different sources of renewable energy: geothermal, solar and wind. Primary data were used for building the life cycle inventories. The geothermal power plant includes emissions treatment for removal of hydrogen sulfide and mercury. The scenario about the substitution of natural emissions from geothermal energy, with specific reference to the greenhouse effect, is also investigated performing a sensitivity analysis. The results are characterized employing a wide portfolio of environmental indicators employing the Recipe 2016 and the ILCD 2011 Midpoint+ methods; normalization and weighting are also applied using the Recipe 2016 method at endpoint level. The results demonstrate a good eco-profile of geothermal power plant with respect to other renewable energy systems and allow for a critical analysis to support potential improvements of the environmental performances.

The environmental safety of a car is currently one of the most important indicators of the vehicle competitiveness and quality in the consumer market. Currently, the assessment of the ecological properties of vehicles can be made based on various criteria. In the case of combustion-powered cars, the most attention is usually paid to the values characterizing their use, and in the environmental assessment, first of all to pollutant emissions and operational fuel consumption. The proposed article considers the possibility of using the life cycle assessment to analyze the ecological properties of a passenger car during its operation. A simplified LCA method of the vehicle was presented, which in strictly defined cases can be used for the analysis of environmental impacts and the assessment of the energy analysis related to its operation. For this purpose, a vehicle life cycle model was developed. Data on the operation of 33 passenger cars of different manufacturers with similar operational characteristics, coming from different production periods, were analyzed in detail. The obtained results were found to be highly sensitive to the assumptions made in the article.

The railway industry focus in the past years was to research, find and develop methods to mitigate noise and vibration resulted from wheel/rail contact along track infrastructure. This resulted in a wide range of abatement measures that are available for the professionals of the industry today. However, although there are many options in the market, their practical implementations depend upon general constraints that affect most technological application in the engineering world. The progression of these technologies have facilitated the selection of more adequate methods for each best case scenario, but further studies are ought to be made to proper assess if each one is fit for their purpose. Every method implementation must be analyzed through budget and timeframe limitations, which includes building, maintenance and inspection costs and time allocation, while also aiming to meet different benefits, such as environmental impact control and wear of the whole infrastructure. There are several situations and facilities in a railway project design that need noise and vibration mitigation methods and each design allocates different priorities for each one of them. Traditionally the disturbance caused by railways to the community are generated by wheel/rail contact sound radiation that expresses in different ways, depending on the movement of the rolling stock and track alignment, such as rolling noise, impact noise and curve noise. More specifically, in special trackworks such as turnouts, the main area of this study, there are two noises types that must be evaluated: impact noise and screeching noise. With respect to the second, it is similar to curve squeals and, being such, its mitigation methods are to be assigned as if it was to abate curve squeal in turnouts and crossings. The impact noise on the other hand, emerges from the sound made by the rolling stock moving through joints and discontinuities (i.e. gaps) that composes these special components of a railway track. A life cycle analysis is therefore substantial for this reality and in this case will be applied to Squeal and Impact Noise on Special Trackwork. The evaluation is based on a valid literature review and the total costs were assumed by industry reports to maintain coherency. The period for a life cycle analysis is usually of 50 years, hence it was the value assumed. As for the general parameters, an area with high density of people was considered to estimate the values for a community with very strict limits for noise and vibration.

The preparation of sulfur-single walled carbon nanohorns active material via a simple and sustainable evaporation method for application as cathode in lithium-sulfur batteries is reported. We show that the synthesis process enables the infiltration of elemental sulfur within the carbon nanohorns thus obtaining a morphology responsible for the ameliorating of the shuttle effect. The sulfur-carbon composite is characterized in terms of structure, morphology, and composition through x-ray diffraction, transmission electron microscopy, and thermogravimetric analyses. From the electrochemical point of view, cyclic voltammetry, rate capability, and galvanostatic cycling tests are performed employing a solution of bis(trifluoromethane)sulfonimide lithium salt and lithium nitrate in a mixture of 1,2-dimethoxyethane and 1,3-dioxolane in order to evaluate the electrode design applicability within lithium-sulfur cells. In this respect, further insights are provided by the estimation of the lithium-ion diffusion coefficient through the Randles-Sevcik equation, and by electrochemical impedance spectroscopy. The obtained results reveal a remarkable cycle life lasting around 800 cycles with a stable capacity of 520 mA h g-1 for the first 400 cycles at C/4, while reaching a value around 300 mA h g-1 at the 750th cycle. These results suggest sulfur-carbon nanohorns active material as a potential candidate for the next-generation battery technology.

The article presents an original method to assess the sustainability of concrete. The method uses three parameters, namely: performance, lifetime and environmental impact, to calculate a sustainability index. The originality and the simplicity of the proposed method presented in the article consists in the fact that by applying the relation to determine the sustainability index, the first two factors service life and performance are constant. This approach is possible in the context of the new proposals to specify the durability of structural concrete in EN 1992 and EN 206. That allows classification of concrete according to its performance, through Environmental action Resistance Classes (ERC). For this purpose, specific experimental methods were used in order to determine the performance of concrete exposed to carbonation. The concretes were prepared with two cement types with additions (CEM II / A-S and CEM II / A-M (S-LL)). Based on the carbonation resistance classes (the first constant - the performance) and exposure classes, the thickness of the concrete cover layer was determined to ensure a certain service lifetime (second constant - the service lifetime). Finally, the global warming potential was calculated for each composition, consequently allowing the users of the method, to select the compositions with the lowest impact on the environment.

This article presents a method to assess the sustainability of concrete based on three elements: service life, performance and environmental impact. The method proposes - to achieve similar performance and service life times, regardless of the component materials used, so that the sustainability assessment ultimately depends on the environmental impact criterion. To this end, specific experimental methods are used to determine the performance of concrete in terms of compressive strength and carbonation resistance for concrete cast with two blended cement types. The procedure needed to classify the concrete through carbonation resistance is detailed, in relationship with the performance obtained for compressive strength. The obtained results highlight the concrete formulations to be used to ensure similar performances regardless of the cement type used. In conclusion, the simplicity in the application of the method, which is closely related to the performance approach on concrete durability in the revision proposals of the European standards, is highlighted. The method is also a useful tool to encourage the widespread use in concrete formulation of blended cements with low environmental impact, without reducing the performance or service life time of the constructions.

End-of-life electric vehicle (EV) batteries can be reused to reduce their environmental impact and economic costs. However, the growth of a second-life market is limited by the lack of information on the characteristics and performance of these batteries. As the volume of end-of-life EVs may exceed the amount of batteries needed for stationary applications, investigating the possibility of repurposing them in mobile applications is also necessary. This article presents an experimental test that can be used to collect the data necessary to fill a battery passport. The proposed procedure can facilitate the decision making process regarding the suitability of a battery for reuse at the end of its first life. Once the battery passport has been completed, the performance and characteristics of the battery are compared with the requirements of several mobile applications. Mobile charging stations and forklift trucks were identified as relevant applications for the reuse of high capacity prismatic cells. Finally, a definition of a state of health (SoH) is proposed to track the suitability of the battery during use in the second life application considering not only energy but also power and efficiency of the battery. This SoH shows that even taking into account accelerated ageing data, a repurposed battery can have an extended life of 11 years at 25~°C. It has also been shown that energy fade is the most limiting performance for lifetime and that cell-to-cell variation should be tracked as it has been shown to have a significant impact on battery life.

The study investigated the impact of traditional medicine on life expectancy in Nasarawa State, Nigeria. The study adopted a quantitative research approach. Purposive or judgmental sampling was used to elucidate the data set used for the study. Cross-sectional data were gathered with the help of a well-designed questionnaire from a total of three hundred and fifty-seven (357) respondents who were available for the survey. The data set collected was analysed using descriptive and linear regression using Ordinary Least Squares (OLS). From the results, 53%, 87%, and 56% were male, below 50 years old, and in the low-income class, respectively, suggesting that the bulk of the respondents under investigation were male, young, and had rather modest incomes. Also, 53% were married, and all had one form of formal education. 67% of respondents acknowledge using traditional medicine; however, the majority of respondents preferred Orthodox medical care over alternative kinds of care. Traditional medicine (TM) and factors that contribute to the advancement of traditional medicine (FITM) have a negative impact on life expectancy, according to the regression analysis. On the other hand, TM has no statistically significant impact on life expectancy, despite FITM having a statistically significant effect at the 5% level. All available data, however, indicates that TM and FITM have an impact on life expectancy, either directly or indirectly. Based on the results, this study concluded that traditional medicine has the potential to significantly increase life expectancy in Nasarawa State and throughout Nigeria. The study recommends that traditional health professionals, stakeholders, and concerned government agencies should put efforts in place to improve and promote modern traditional medicine among the people, especially its effectiveness and medicinal quality, increase its accessibility to people, and efficiently regulate its prices to increase its affordability for low-income earners

A proposed low-temperature forging method aims to enhance stainless steel bearings by creating a martensitic subsurface layer, significantly boosting bearing fatigue life due to increased surface hardness. This technique induces beneficial residual stresses, particularly in axial bearings, streamlining their construction and improving machine elements. Challenges persist, especially with radial bearings, but simplicity in axial bearing forging promotes compact, resource-efficient facility construction. Future research will focus on applying this technique to axial bearing washers, potentially replicating success in other bearing components. Despite the energy ex-penditure for cooling during forging, the substantial increase in bearing fatigue life offsets this, enhancing overall longevity and reliability of critical machine components. Integration of this forging technique into bearing fabrication appears seamless, offering a promising trade-off be-tween energy use and enhanced performance.

The evaluation of geometric defects is necessary in order to maintain the integrity of structures over time. These assessments are designed to detect damages of structures and ideally help inspectors to estimate the remaining life of structures. Current methodologies for monitoring structural systems, while providing useful information about the current state of a structure, are limited in the monitoring of defects over time and in linking them to predictive simulation. This paper presents a new approach to the predictive modeling of geometric defects. A combination of segmented from point clouds are parametrized using the convex hull algorithm to extract features from detected defects, and a stochastic dynamic model is then adapted to these features to model the evolution of the hull over time. Describing a defect in terms of its parameterized hull enables consistent temporal tracking for predictive purposes, while implicitly reducing data dimensionality and complexity as well. In this study, 2D point clouds analogous to information derived from point clouds were first generated over simulated life-cycles. The evolutions of point cloud hull parameterizations were modeled as stochastic dynamical processes via autoregressive integrated moving average (ARIMA) and vectorized autoregression (VAR) and compared against ground truth. The results indicate that this convex hull approach provides consistent and accurate representations of defect evolution across a range of defect topologies and is reasonably robust to noisy measurements, however assumptions regarding the underlying dynamical process play a significant the role in predictive accuracy. The results were then validated on experimental data from fatigue testing with high accuracy. Longer term, the results of this work will support finite element model updating for predictive analysis of structural capacity.

This paper presents the life cycle assessment results of a study of plastic recycling via hydrothermal upgrading (HTU), a chemical recycling technology. It was investigated due to its potential to address current gaps in the plastic recycling system, largely due to several plastic packaging materials and formats that cannot be processed by traditional mechanical recycling technologies (primarily due to technoeconomic reasons). As society transitions towards a net-zero-based circular economy, assessments should be conducted with a futuristic outlook, preventing costly mistakes by employing the right technologies in the right areas. HTU can generate up to 76% reduction in climate change impacts when compared with comparable end-of-life treatment technologies whilst conserving material with the system. Additionally, further reductions could be achieved by changes in electricity consumption within the study. This represents a new insight to chemical recycling of polymers by establishing a prospective life cycle assessment study that looks to introduce a step-change in the recycling system. By creating a transparent cut-off model with consistent allocation, it highlights the benefits of introducing this technology as opposed to the current model of disposal through incineration or landfill.

Background: Music therapy (MT) is a non-pharmacological treatment increasingly used to reduce stress and anxiety in hospitalized children affected by cancers. The aim of this study was to eval-uate the impact of MT on quality of life of children with cancer. Methods: We have conducted a quasi-experimental study between April 1 and August 31, 2021 at Bechir Hamza children's Hos-pital in Tunis, including children treated for cancer. The child or the parent completed PedsQL Module Cancer french version 3.0 questionnaires before and after four weekly music therapy ses-sions. Child's respiratory and heart rate were measured before and after each session. Results: We included 20 children whose mean age was 7 ± 4.5 years [2-14]. The median value of the total questionnaire score increased from 57 [46; 70] to 72 [67; 85] (p < 10-3) with a significant reduction in pain (p = 0.02), nausea (p = 0.009), anxiety related to medical procedures (p = 0.009) and worry about the future (p = 0.005). We highlighted a significant decrease in respiratory and heart rate after MT (p<0,05). Conclusions: MT has positive impact of on quality of life of children with cancer.

Today’s purchasing companies demand an advanced buyer equal of enactment from their supplier while the two parties maintain a respectful connection. Although the supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. In this study, we applied two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology comapny; this cloud make company decision–makers focus on low PLCC and select better supplier.

Physical activity is especially important of children's everyday life with chronic disease. The aim of the study was to show whether asthma is a barrier to physical activity in our society. The correlation between the severity of the disease, body mass index, and physical activity were analyzed, and, parents' opinion whether children should participate in active sports was assessed. Physical activity of children with asthma was analyzed by questionnaires and activity-measuring armbands. 93 parents and their children were involved in the survey, while 20 children were wearing the armband. The age of children was 12.6±3.5 years (mean±SD), 69.9% were boys, 30.1% were girls. 93.4% of the respondents participated in physical education program and 56.5% also attended sporting activities on a regular basis. 61.2% of the children had mild, 37.6% moderate, and 1.2% severe asthma. 6.5% of the respondents stated that their illness had been consistently or frequently limiting the performance concerning their school or home duties over the past 4 weeks. Twelve percent of parents felt that physical activity was not appropriate in the context of this disease. We conclude, that fear of the consequences of physical activity depends largely on education which should involve their parents, teachers and coaches.

Supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. In this study, we applied two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology company; this cloud makes company decision–makers focus on low PLCC and select a better supplier in sustainable supply chains goal.

In recent years, due to the low energy utilization of the whole life-cycle of buildings and the di-minished indoor and outdoor comfort of buildings and the impact on the surrounding environ-ment caused by the carbon emissions of the building life-cycle, the establishment of a whole life- cycle carbon emission model for buildings to improve their energy utilization at all stages of their life-cycle has received unprecedented attention. In China, the construction industry has become a major carbon emitter, and traditional houses, as a green development building type, are an effec-tive way to achieve carbon neutrality in buildings, but the existing green building evaluation system lacks quantitative indicators of carbon emissions in the building life-cycle. The exclusive evaluation indexes for regional and characteristic buildings, such as traditional houses, are ne-glected; This study explored the formula for calculating the life-cycle carbon emissions model of traditional residential houses under a carbon emission intervention and used real measurements of the physical environment and comparative analysis of the limitations of existing local stand-ards; The results showed that the carbon emission calculation formulas for each stage of the life-cycle of traditional residential houses must be established by combining the selection of local building materials, and the materials for sustainable energy and carbon sinks of green systems. Based on the results of indoor and outdoor heat and humidity environmental tests of residential houses and an analysis of the limitations of existing evaluation indexes due to locality, four im-portant factors affecting locality green buildings in terms of energy utilization, site ecology and landscape, land saving and material saving were extracted; on this basis, the whole life-cycle carbon emission model of traditional residential houses is constructed by combining the existing green building evaluation standards with the carbon emission indexes of the life-cycle of tradi-tional residential houses.

Using the PLCC advantages generates revenue and lowers costs more than might be anticipated. It ensures better decisions by using a more perfect and practical assessment of revenues and costs. Although the supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. In this study, we applied two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology company; this cloud make company decision–makers focus on low PLCC and select better supplier.

Hearing loss that arises from various causes at different stages of life has a direct impact on individuals' physical and mental well-being. This paper aimed to evaluate the employment, workplace adaptation, productivity, and professional success of individuals who have hearing loss and whose hearing loss is corrected with a cochlear implant. In this cross-sectional study, the data was collected between November 2022 and March 2023 with the participation of individuals with cochlear implants living in several settlements in all regions of Türkiye. A total of 142 participants with severe hearing loss who were corrected with a cochlear implant were included in this study. The survey method was used to collect data for the study. The questionnaire consisted of 32 questions and was distributed to the participants online. In the first part of the questionnaire (1-10 questions), general characteristics of implant patients were investigated. In the second part (11-32 questions), the positive or negative effects of implantation on the work life of the participants were evaluated. Almost half of the research group (49.3%, n = 70) consisted of women, and the mean age of the participants was determined to be 35.8 ± 14.8. There was no significant difference between gender, educational status, implanted side, working time, working style (physical, desk), and factors affecting work life (p > 0.05). Professional satisfaction and success at work increased significantly more in those with acquired hearing loss (p = 0.010). Post-implantation workplace compliance, success, and productivity were found to be higher in those with acquired hearing loss (p = 0.013). It was observed that hearing loss had a greater negative impact on the work life of married people (p = 0.006). Cochlear implantation greatly enhances workplace satisfaction, increases self-confidence, and has a positive impact on the future of profoundly deaf individuals.

The Glasgow Declaration called for scientifically based measurements of CO2 emissions in the tourism industry to achieve the goals of the Paris Agreement. Despite the economic and employment downturn caused by COVID-19, there are limited cases of environmental assessments related to tourism. This study estimates the carbon footprint of the tourism industry in major G20 countries before and after COVID-19. Understanding the characteristics of inbound tourism and domestic tourism is important as they impact different markets. GHG emissions from tourism mainly stem from transportation, but the type of travel and country differences also make souvenirs, accommodation, and food and beverages significant emission factors. The pandemic has greatly impacted the tourism industry. In 2020, GHG emissions from both domestic and inbound tourism significantly decreased, affecting the number of tourists. In some countries, measures against COVID-19 influenced these figures, and although signs of recovery were observed in 2021, the reduction rates varied by country. These emission reductions should be the goals pursued by the tourism industry in the post-COVID-19 era, requiring efforts to achieve sustainable tourism.

Supplier selection (SC) continues to be a crucial component in manufacturing procurement. Using the PLCC advantages generates revenue and lowers costs more than might be anticipated. Supplier selection (SC) product life cycle cost (SCPLCC) is an important consideration among corporations, SCPLCC problem has become associated with deciding how one supplier should be selected from possible alternatives. Past literature on this topic is limited. We try to close this gap in knowledge. In this study, we attempt to apply two types of goal programming, multiobjective linear programming and revised multichoice goal programming to develop a PLCC-based concept to solve the SCPLCC problem and construct a decision-making tool for application to a case of supply chain management in a Taiwanese light-emitting diode company in the high-tech industry. Our study main contribution Company managers can easily use the two approaches of the SCPLCC model with different parameters to solve SCPLCC model problems. Finally, we are comparing five models found RMCGP with weighted linear goal programming had an adequate effect for application to the PLCC concept for high-technology Company; this cloud makes company decision–makers focus on low PLCC and select a better supplier in sustainable supply chains development.

The colpodellids consist of free-living predatory protists phylogenetically related to pathogenic Apicomplexan parasites such as Plasmodium species, Cryptosporidium sp. and Toxoplasma gondii. Among the colpodellids, Colpodella species prey on bodonids, algae, and ciliates. Voromonas pontica preys on Percolomonas species. In the past decade, Colpodella species have been reported to cause opportunistic infections in humans and animals, and having the potential for zoonotic infections in humans due to the presence of Colpodella species in ticks. In the reported cases, transmission and pathogenic stages of Col-podella were not identified by light microscopy. In the colpodellid V. pontica, cyst stages of both the pred-ator and its prey Percolomonas cosmopolitus have not been identified by light microscopy. In this study we evaluated the dye components used for Sam-Yellowe’s trichrome staining, from different major vendors to determine the consistency and reproducibility of the staining protocol to aid the use of the staining proto-col for diagnosis. We show that although slight variations in the color of the stained cells are obtained, life cycle stages of Colpodella ATCC 50594 could be clearly identified, regardless of the vendor used. For the first time, Sam-Yellowe’s trichrome staining series, could identify cysts of V. pontica and its prey, demonstrating that the staining protocol can identify life cycle stages of other colpodellids. Sam-Yellowe's trichrome staining will aid molecular diagnosis of infections caused by colpodellids in human and ani-mals, identify colpodellids in ticks and flies and from environmental samples, when used for staining.

Municipal solid waste management is a major concern for developing countries all over the world. The collection and transportation accounts for major portion of expenditure in developing country like India. The compaction of waste is being practiced in some major cities of India as they provide economical benefit but the environmental benefits of compaction are not very clear. The preset study evaluates the environmental impacts due to transportation of non-compacted and compacted waste from the transfer station to the landfill site using life cycle assessment approach. The study compared transportation of non-compacted waste with the waste compacted by the truck mounted refuse compactor and portable stationary compactor. The functional unit defined was the amount of waste generated per day in the study area taken as Patna city and GaBi 10.5 used for impact assessment. The study found that the transportation of waste compacted by truck mounted refuse compactor had the least environmental impacts on all impact categories. The study recommends the compaction of waste by the truck mounted refuse compactor and then proceed for transportation. Also, the compaction of waste is recommended as it improve the overall environment performance of municipal solid waste management.

Banana plantation is an important type of agro-ecosystem in the tropics, and it is important to carry out a quantitative assessment of the carbon footprint of the banana growing process for the development of low-carbon agriculture to cope with global warming. The carbon footprint of two banana cultivation processes was assessed using the life cycle assessment method through field trials and farmer surveys in Chengmai County, Hainan Province, China. The results showed that: (1) N2O emissions caused by the application of nitrogen fertilizers and compound nitrogen fertilizers were the largest source of carbon emissions from banana plantation farmland, and the production and transportation of common compound fertilizer were the second largest source of carbon emissions. Banana fruits and plants were the main contributors to carbon fixation in banana plantation ecosystems, with about 24.72 t CO2 eq hm-2 for Musa paradisiaca AA, and 34.66 t CO2 eq hm-2 for M. AAA Cavendish var. Brazil. (2) The annual carbon emissions of Musa paradisiaca AA and M. AAA Cavendish var. Brazil farmland systems were 35.40 t CO2 eq·hm-2 and 43.83 t CO2 eq·hm-2, respectively, and the annual carbon fixation was 38.23 CO2 eq·hm-2 and 48.17 CO2 eq·hm-2, respectively. The banana plantations had a negative carbon footprint per unit area, showing a net carbon sink function. (3) Banana is a plant with high carbon emission and strong carbon fixation capacity. Scientific management in the field can achieve the decrease of agricultural inputs, high quality and abundant agricultural products, and the reduction of carbon footprint of farmland.

This paper establishes a prognosis of the long term environmental impact of various car subsidy concepts. The CO2 emissions of the German car fleet impacted by the purchase subsidies are determined. A balance model of the CO2 emissions of the whole car life cycle is developed. Consideration of production-, use- and End-of-Life processes are taken into account. The implementation of different subsidy scenarios directly affects the forecasted composition of the vehicle population and therefore the resulting life cycle assessment. All scenarios compensate the additional emissions required by the production pull-in within the considered period and hence reduce the accumulated CO2 emissions until 2030. The exclusive funding of BEVs is most effective with a break-even in 2025.

Autism Spectrum Disorder (ASD) is a neurodevelopmental condition, characterized by persistent deficits in communication/social interaction and restricted and repetitive patterns of behavior, interests or activities. It is usually identified in childhood, despite late diagnoses in cases of greater functionality. Havighurst proposes a set of fundamental tasks throughout the life cycle, whose achievement is probably compromised in the ASD, even though it lacks scientific evidence. This study innovates, as it is based on Havighurst's theoretical model for understanding the development process of three adults and one young person, diagnosed with ASD level I, at different life stages. Through the methodology of life histories, interviews were subject to content analysis. Results pointed out the early detection and interventions importance, minimizing adversities, above all by those who had late diagnoses. Self-perceived success, not expected, was found in some development tasks (e.g. conscience and morality development). Also were noticed expected limitations related to ASD (e.g. difficulties in relationships with peers and in the labor market inclusion). Probably, in cases of greater severity and less functionality/autonomy, there would be greater failure in development tasks. It is crucial to improve research on this developmental model and on the factors that delay the diagnosis, including cases of different levels of severity.

Biomass-derived carbon dots (CDs) are gaining much interest in recent times as it is a sustainable option with abundant availability, low cost, and tunable luminescence. Herein, we report a simple green synthesis method to produce highly fluorescent CDs from Eucalyptus globulus leaves using the one-pot hydrothermal approach. The fabricated CDs exhibit strong blue fluorescence with an excitation and emission maxima of 340 nm and 442 nm respectively. The highest quantum yield (QY) obtained was 60.7%. Due to its promising optical properties and biocompatibility, CDs can be a potential candidate for biosensing applications. Moreover, we employed a life cycle assessment (LCA) cradle-to-gate approach to study the environmental impacts of the synthesis strategy used for the fabrication of CDs. The results point out that citric acid is a main hotspot in CDs synthesis, regarding environmental impacts in most categories. This justifies the introduction of biomass, which reduces the amount of citric acid, thus leading to a more sustainable synthesis strategy for fabricating CDs.

The purpose of this study was to model the impact of mentoring on women’s work-life balance. Indeed, this study considered mentoring as a solution to create a work-life balance of women. For this purpose, semi-structured interviews with both mentors and mentees of Tehran Municipality were conducted and the collected data were analyzed using constructivist grounded theory. Findings provided a model of how mentoring affects women's work-life balance. According to this model, role management is the key criterion for balancing work-life of women. In this model, antecedents of role management and the contextual factors affecting role management, the constraints of mentoring in the organization, as well as the consequences of effective mentoring in the organization are described. The findings of this research contribute to the mentoring literature as well as to the role management literature and provide recommendations for organizations and for future research.

Introduction: The majority of epidemiological reports focus on confirmed cases of COVID-19. In this study, we aim to assess the health and well-being of adults not infected with Covid-19 after two months of quarantine in Morocco. Materials and methods: Two months after the declaration of quarantine in Morocco following the Covid-19 epidemic, we carried out a descriptive cross-sectional study of 279 Moroccan citizens. We used the Short Form Health Survey (SF-12) as a determinant of quality of life, which is based on eight dimensions of health. The data were collected using an electronic questionnaire distributed online. The participants also indicated their socio-demographic data, their knowledge and practices regarding the Covid-19 pandemic and whether they had chronic health problems. Results: The quality of life of all participants was moderately disrupted during the Covid-19 pandemic with a mental health score (MCS) of 34.49 (± 6.44) and a physical health score (PCS) of 36.10 (± 5.82). Participants with chronic diseases scored lower with 29.28 (± 1.23) in mental health (MCS) and 32.51 (± 7.14) in physical health (PCS). The seriousness of COVID-19 has an impact on the quality of life and health well-being of people and this impact is more marked in people with chronic health problems. Conclusion: Our results confirm the need to pay attention to the health of people who have not been infected with the virus. Our results also point out that uninfected people with chronic illnesses may be more likely to have well-being problems due to quarantine restrictions.

This study investigated mortality discrepancies in Korea, 2000-2020, with a focus on age, gender, and preventable causes of death, and their impact on life expectancy at birth. The study utilized data from Korean Standard Classification of Diseases and OECD/Eurostat lists of preventable and treatable causes of death and employed Arriaga's method. Noteworthy findings revealed gender disparities in life expectancy increases, with male gaining an advantage over females from 2000-2020 (8.142 years for males versus 6.806 years for females). The most significant increase in life expectancy was found to be in males aged 70-74 and females aged 75-79. The gender gap in LEB is narrowing and that the main age group contributing to the gender gap are getting older. Reduced gains in life expectancy at birth resulted from avoidable mortality, contributing 57.3% to the increase. Cerebrovascular disease and transport accidents were positive contributors, whereas suicide and certain cancers were negative contributors. The changes in mortality for individuals aged 65 and over had an impact of 45.44% (males) and 71.01% (females) on life expectancy gains. This study offers a novel approach in evaluating avoidable mortality and life expectancy, having the potential to improve international health indicators and inform health policies.

This work can be considered as a first step of designing a future competitive data-driven approach for remaining useful life prediction of aircraft engines. The proposed approach is an ensemble of serially connected extreme learning machines. The results of prediction of the first networks are scaled and fed to the next networks as an additive features to the original inputs. This feature mapping allows increasing the correlation of training inputs with their targets by holding new prior knowledge about the probable behavior of the target function. The proposed approach is evaluated under remaining useful estimation using a set of “time-varying” data retrieved from the public dataset C-MAPSS (Commercial Modular Aero Propulsion System Simulation) provided by NASA. The prediction performances are compared to basic extreme learning machine and proved the effectiveness of the proposed methodology.

This paper focuses on quantifying the economic and financial viability of NB-IoT and LoRaWAN technologies, two low-power wide-area network (LPWAN) technologies with unique characteristics that make them suitable for IoT applications. The purpose of the study is to propose an artefact for performing life cycle cost analysis and demonstrate its application to these technologies. The methodology uses pragmatic computational tools to facilitate the analysis and considers all relevant economic and financial factors, such as operating costs, equipment costs, and revenue potential. The main finding of the study is that NB-IoT and LoRaWAN technologies have different cost structures and revenue potentials, which may affect their economic and financial viability for different IoT applications. Ultimately, the study concludes that a comprehensive life cycle cost analysis is critical to making informed decisions about technology adoption, and that the proposed methodology can be applied to other IoT technologies to gain insight into their economic and financial viability.

The fatigue life of concrete is affected by many interwoven factors whose effect is nonlinear. Be-cause of its unique self-learning ability and strong generalization capability, the Bayesian regu-larized backpropagation neural network (BR-BPNN) is proposed to predict concrete behavior in tensile fatigue. The optimal model was determined through various combinations of network parameters. The average relative impact value (ARIV) was constructed to evaluate the correla-tion between fatigue life and its influencing parameters (maximum stress level Smax, stress ratio R, static strength f, failure probability P). ARIV results were also compared with other factor as-sessment methods (weight equation and multiple linear regression analyses). Using BR-BPNN, S-N curves were then obtained for the combinations of R=0.1, 0.2, 0.5; f=5, 6, 7MPa; P=5%, 50%, 95%. The tensile fatigue results under different testing conditions were finally compared for compatibility. It was concluded that Smax has the most significant negative effect on fatigue life; the degree of influence of R, P, and f, which positively correlate with fatigue life, decreases suc-cessively. ARIV is confirmed as a feasible way to analyze the importance of parameters and could be recommended for future applications. The tensile fatigue performance of plain concrete under different stress states (flexural tension, axial tension, splitting tension) does not differ sig-nificantly. Besides utilizing the valuable fatigue test data scattered in the literature, insights gained from this work could provide a reference for subsequent fatigue test program design and fatigue evaluation.

The work presents the results of numerical fatigue analysis of a turbine engine compressor blade, taking into account the values of initial stresses resulting from surface treatment - shot-peening. The values of the residual stresses were estimated experimentally using X-ray diffraction. The paper specifies the values of the residual stresses on both sides of the blade and their reduction due to the cutting through the blade - relaxation. The obtained values of the residual stresses were used as initial stresses in the numerical fatigue analysis of the damaged compressor blade, which is subjected to resonant vibrations of known amplitude. Numerical fatigue ε-N life analysis was based on the several fatigue material models: Manson’s, Mitchell’s, Baumel-Seeger’s, Muralidharan-Manson’s, Ong’s, Roessle-Fatemi’s and Median’s, and also on the three models of cyclic hardening: Manson’s, Xianxin’s, and Fatemi’s. Because of this approach, it was possible to determine the relationship between the selection of the fatigue material ε-N model and the cyclic hardening model on the results of the numerical fatigue analysis. Additionally, the calculated results were compared with the results of experimental research, which allowed for a substantive evaluation of the obtained results. These results are of great scientific and practical importance. The problem of determining the fatigue life of blades with defects operating under resonance vibrations is one of the original tasks in the field of fracture mechanics and experimental mechanics. The results obtained are of great importance in the aviation industry and can be used during engine maintenance and inspections to assess the suitability of blades with defects in terms of the needs of further work. This aspect of engineering maintenance is of great importance from the aircraft safety point of view.

Background: Chronic disease is the leading cause of death and disability in children. Various complex stressors faced by children due to illness and a series of treatments can negatively impact children's welfare, which can negatively affect children's quality of life.Objectives: This literature aims to study the philosophy of spiritual-based care interventions to improve the quality of life of children with chronic diseases viewed from three philosophical perspectives, namely ontology, epistemology, and axiology.Methods: A literature search was performed on five databases, namely SCOPUS, PubMed, ProQuest, ScienceDirect, and SAGEPub. Population limitations and diagnoses in this literature of children with chronic disease. This research is a quantitative study focusing on publications between 2017-2021.Results: The philosophy of spiritual care intervention is humanistic, pragmatic, and religious intervention. Humanistic interventions are interventions in which nurses are actively involved in spiritual care. Pragmatic intervention is the activeness of a nurse in assessing the spiritual needs of patients. Meanwhile, religious intervention is an intervention that is directly related to the practice or ritual of a specific belief system. Spiritual care is an essential part of holistic care, which is considered an indicator of improving the quality of care. It will ultimately affect the optimal quality of life of children.Conclusion: Spiritual-based care interventions are essential to improve the quality of life of children with chronic diseases. Spiritual care given to children with chronic illnesses must consider all aspects such as developmental stage, life experience, and socio-cultural of the child.

In this follow-up study, we aimed to assess the effectiveness of the “I do not smoke, I exercise”, anti-smoking preventive health education program. The program was based on the Theory of Planned Behavior supplemented with life-skills teaching and targeted at high school students. The intervention comprised ten one-hour online sessions, administered by physical education instructors. The study cohort comprised 222 students (109 boys, 113 girls) from 11 secondary schools, with an average age of 16.42 ± 1.36 years. Data collection involved pre- and post-intervention self-assessment questionnaires. The examined variables included attitudes towards smoking, intention to smoke, subjective norm, perceived behavioral control (PBC), knowledge about smoking, smoking behavior, exercise behavior, attitudes toward the program's implementation, and satisfaction with the program. Separate paired samples t-test revealed a significant improvement in students' knowledge about smoking, perceived behavioral control, and overall program satisfaction following the intervention. However, no significant changes were observed in the remaining variables. These findings suggest that the health education smoking prevention intervention incorporates techniques and strategies that influence the Perceived Behavioral Control variable, emphasizing students' strong interest in educationally theorized programs integrating technology into their design. Future studies should consider further examination of tobacco control strategies within the high school context.

The treatment of cancer and associated healthcare procedures often impose a detrimental effect on patients’ quality of life. Symptoms stemming from treatment often hinder patients’ social interactions, emphasizing the crucial role of social support in preserving quality of life and alleviating stress. Moreover, patient resilience serves as a valuable asset in mitigating stress levels and upholding an optimal quality of life amidst the challenges posed by the illness. This study aims to explore the correlation between diverse sources and forms of social support, resilience, and their impact on the quality of life and stress levels among patients undergoing cancer immunotherapy. This study involved thirty patients undergoing immunotherapy at Costa del Sol Hospital in Marbella. Resilience correlated with improved cognitive functioning and diminished symptoms. Informational support from healthcare providers and emotional support from friends were linked to symptom alleviation, such as reduced appetite and insomnia. Moreover, emotional support from friends emerged as a predictor for decreased perceived stress. Interventions targeting the improvement of quality of life and reduction of stress among cancer patients should prioritize assessing support needs and involving the patient's social network, especially during the treatment phase.

Colorectal cancer remains one of the most commonly diagnosed cancers. Advanced rectal cancer patients receive neoadjuvant radiochemotherapy as well as surgery and suffer under reduced health-related quality of life due to various side effects. We were interested in the role of the COVID-19 pandemic and how it affected those patients’ quality of life. A total of 489 advanced rectal cancer patients from the University Hospital Erlangen in Germany were surveyed between May 2010 and March 2022 and asked to fill out the EORTC QLQ-C30 and QLQ-CR38 questionnaire over eight different time points: in the beginning, during and after radiochemotherapy, right before surgery and in yearly intervals after surgery for up to four years. Answers were converted to scores to compare the COVID-19 period to the time before March 2020 focusing on the follow-ups, the developments over time – including by sex and age - and the influence of the TNM cT-stage. Overall, a trend of impaired functional and symptom scores was found across all surveys with few significances (body image -10.6 percentage points (pp) after one year; defecation problems +13.5 pp, insomnia +10.2 pp and weight loss +9.8 pp after three years; defecation problems +11.3 pp after four years). cT4-stage patients lost significantly more weight than their cT1-3-stage counterparts (+10.7 to 13.7 pp). Further studies should be conducted to find possible causes and develop countermeasures for future major infectious diseases.

The aim of this paper is to analyze and evaluate Renewable Energy Sources (RES) usage and their contribution to citizens’ life quality. For this purpose, a survey was conducted, using a sample of 400 residents in an urban area of Attica region in Greece. The methods of Principal Components Analysis and Logit Regression were used on a dataset containing respondents’ views on various aspects of RES. Two statistical models were constructed for the identification of the main variables that are associated with RES’ usage and respondents’ opinion on their contribution to life quality. The conclusions that can be drawn show that the respondents are adequately informed about some of the RES’ types while most of them use at least one of the examined types of RES. The benefits that RES offer, were the most crucial variable in determining both respondents’ perceptions on their usage and on their contribution to life quality.

Ankylosing spondylitis (AS) is a chronic inflammatory arthritis that affects the axial skeleton, causing intense pain, progressive joint destruction, and a gradual reduction in physical function. It has been recognized not only as affecting the axial skeleton but as a systemic disease. Since it also causes an increase in the rates of inflammatory bowel disease, psoriasis, acute anterior uveitis, and mental disorders affecting the quality of life. Furthermore, an association with neurological and cardiovascular events is documented. With the advent of biologics, treating AS dramatically changed due to its high efficacy and tolerable safety. AS can be treated with various biological treatments. Nevertheless, there are differences in traits, including rapidity of onset, long-term efficacy, safety profile, and influence on comorbidities. A better understanding of such traits enables clinicians to make the best decision for each patient, increasing persistence, extending medication survival, enhancing patient satisfaction, and reducing the disease effect of ankylosing spondylitis. In this article, we emphasize biologics' efficacy and safety profile in patients with ankylosing spondylitis. In addition, we discuss the impact of biologics on comorbidities and health-related quality of life.

The ubiquity of amino acids in carbonaceous meteorites has suggested that amino acids are widespread in the Universe, serving as a common class of components for the emergence of life. However, parameters for modeling amino acid polymerization at mineral–water interfaces remain limited, although the interfacial conditions inevitably exist on planets with surface liquid water. Here, we present a set of extended triple-layer model parameters for aspartate (Asp) and aspartyl-aspartate (AspAsp) adsorptions on ferrihydrite, anatase, and γ-alumina determined based on the experimental adsorption data. By combining the parameters with the reported thermodynamic constants for amino acid polymerization in water, the impacts of these minerals on Asp dimerization are calculable over a wide range of environmental conditions. It was predicted, for example, that ferrihydrite strongly increases the AspAsp/Asp equilibrium ratio in neutral to acidic pH; the ratio in the adsorbed state reaches 40% even from a low Asp concentration (0.1 mM) at pH 4. This percentage is approximately 5 × 107 times higher than that attainable without mineral (8.5 × 10–6%). Our exemplified approach enables us to screen wide environmental settings for abiotic peptide synthesis from a thermodynamic perspective, thereby narrowing down the geochemical situations to be explored for life’s origin on Earth and Earth-like habitable planets.

In the present paper, we investigate the impact of the timescale factor on the quality of life index behavior on specific time intervals characterized by the presence of socio-economic, political, and/or health severe movements such as pandemics and crises. We essentially aim to show that effectively the quality of life measuring based on a single index in the existing studies may be described more adequately by a variable index due to the social, political, economic, and also healthy environment. The variability discovered is expressed by the existence and the estimation of a multi-index instead of a single one relatively to many factors. Our focus is mainly on the effect of the COVID-19 pandemic on the quality of life. Our model is applied empirically to a sample corresponding to Saudi Arabia as a case of study during the period from January 1990 to December 2021 as the main period affected by the COVID-19 pandemic. The sample is based on social media conversations and texts discussing and describing the satisfaction with the quality of life. The study confirms effectively that the role of the timescale factor is more described when considering a multi-index rather than measurement on the whole time interval.

The Sarcoma Assessment Measure (SAM) was developed as a sarcoma-specific patient-reported outcome measure to be used in clinical practice. We have reported in detail how SAM has been developed in collaboration with patients and healthcare professionals. The aim of this paper is to report the preliminary validation of SAM. The 22-item SAM was administered alongside a validated quality of life questionnaire and measure of activities of daily living. Linear modelling was used to build a measure, which had predictive validity in comparison to more established outcome measures. Of the 762 patients who participated in the study, 44.1% identified as male, and participant age ranged from 13-82 years. Clinically, participants presented with a range of soft tissue (82.2%) and bone (21.8%) sarcomas. Our preliminary analysis indicates that SAM accounts for 35% of the Global quality of life scale and 18% of the TESS so psychometrically it overlaps with quality of life and activities of daily living, but also measures distinct concerns. This demonstrates that this measure picks up issues that are important to patients with sarcoma that are not reflected in other measures. We have established the preliminary validity of SAM and believe it has utility as a patient-reported outcome measure both as a research tool and for assessing the impact of symptoms and dysfunction related to sarcoma as part of clinical care. Further validation using a larger and more clinically diverse sample is now needed.

Fossil-based emissions can be avoided through using wood in place of non-renewable raw materials as energy and materials. However, increasing wood harvest influences forest carbon stocks. This effect may reduce the overall climate benefit of wood use significantly but is widely overlooked. We carried out a systematic review of simulation studies and compared differences in forest carbon and amount of wood harvested between more and less intensive wood harvest scenarios for three different time perspectives; short (1-30 years), mid (31-70 years) and long (71-100 years). Out of more than 450 reviewed studies 44 provided adequate data. Our results show that increased harvesting reduced carbon stocks over 100 years in temperate and boreal forests roughly 1.6 (stdev 0.9) t_C per t_C harvested. The value proved to be robust when outliers explicitly influenced by other factors than change in harvest rate, such as increase in fertilization or forest area, were removed. Interestingly, no significant difference in carbon impacts was found for average values of boreal and temperate forests or between short and long time-horizons. However, impacts tend to be greatest in the mid-term. This carbon balance indicator that we estimated can be interpreted as carbon debit of wood harvest in forests. It is significant compared with the typical GHG credits in technosphere generated by avoiding fossil emissions in substitution and increase in carbon storage in harvested wood products, and should not be ignored. Our estimates provide default values that can directly be included in GHG balances of products or assessment of mitigation policies and measures related to wood use. However, more systematic scenarios and transparent data in which different factors influencing forest carbon stocks are separately studied are clearly required to provide better constrained estimates for specific forest types.

The aim of this study was to determine whether a rowing training program improved the quantity and quality of physical activity and quality of life in female breast cancer survivors (stage I - 4.35%; II - 30.43%; III - 52.17%; and IV - 8.7%) diagnosed 6.57 ± 5.02 years previously, who had undergone a subsequent intervention (preservation 53.52%; total mastectomy 39.13% and double mastectomy 4.35%) and had a current mean age of 53.70 ± 7.88 years. The participants (N = 30) engaged in a 12-week training program, each week comprising three sessions and each session lasting 60-90 minutes. An anthropometric evaluation was performed before and after the program. The short form of the International Physical Activity Questionnaire (IPAQ-SF) and the Short Form 36 Health Survey (SF-36) were also administered. The results showed statistically significant improvements in levels of physical activity and in the dimensions of quality of life. We can conclude that a 12-week rowing training program tailored to women who have had breast cancer increases physical activity levels, leading to improved health status and quality of life.

The aim of this study was to determine whether a rowing training program improved the quantity and quality of physical activity and quality of life in female breast cancer survivors (stage I - 4.35%; II - 30.43%; III - 52.17%; and IV - 8.7%) diagnosed 6.57 ± 5.02 years previously, who had undergone a subsequent intervention (preservation 53.52%; total mastectomy 39.13% and double mastectomy 4.35%) and had a current mean age of 53.70 ± 7.88 years. The participants (N = 30) engaged in a 12-week training program, each week comprising three sessions and each session lasting 60-90 minutes. An anthropometric evaluation was performed before and after the program. The short form of the International Physical Activity Questionnaire (IPAQ-SF) and the Short Form 36 Health Survey (SF-36) were also administered. The results showed statistically significant improvements in levels of physical activity and in the dimensions of quality of life. We can conclude that a 12-week rowing training program tailored to women who have had breast cancer increases physical activity levels, leading to improved health status and quality of life.

Caring for an ill or disabled relative can present significant challenges that may exceed the per-sonal resources of the caregiver. Young carers (YCs) often take on this role, providing support to family members or friends, which can have far-reaching effects on various aspects of their lives. This study involved 235 adolescents, 106 YCs and 129 non-carers (NCs), who completed ques-tionnaires assessing life satisfaction, social support, family functioning, academic functioning, and caring activities. Group effects measured with MANOVA and MANCOVA (controlling for age effects), showed YCs to have higher amounts of caregiving activities than NC (as expected) but lower satisfaction with life. Hierarchical regressions also found that, for YCs, academic func-tioning, social support and the negative impact of caregiving predicted satisfaction with life; and that the negative impact of caregiving on YCs is explained by their family functioning and the amount of their caregiving activities. For NCs, only academic functioning, social support and family functioning predicted satisfaction with life. In conclusion, caregiving has a negative im-pact on YC’s life satisfaction, but this effect is determined by their social support, academic func-tioning and negative impact of caring, which in turn depends on their familiar functioning and amount of caring activities.

COVID‑19 pandemic, also known as the coronavirus pandemic, has spread rapidly across the globe since the end of 2019 and brought impressive changes in our life and living through partial or full lockdown and reduced anthropogenic activities. Hence, it is imperative to investigate the impacts and consequences of COVID-19 on global eco-system and environment. The present study accordingly addresses the impacts and consequences of COVID-19 by ten environmental indicators; viz., global warming (or greenhouse gas emission), stratospheric ozone depletion, ozone formation (on human health), fine particulate matter formation, smog, ionizing radiation, human carcinogenic toxicity, human non-carcinogenic toxicity, water resource consumption, and effect on human health. The overall study has been performed in agreement with the standard principle and guidelines of life cycle assessment. Worldwide changes in consumption of fossil fuels, viz., petroleum, coal and natural gas, as a result of COVID-19 pandemic, has been the core theme of the study. Outcomes from the study show that COVID-19 has been a ‘blessing in disguise’ for the global environment with most of the above-mentioned indicators declining by approximately 20-30% in 2020 in comparison to the 2019 level.

Reversed Flow Gas Chromatography (R.F.G.C.) was employed to assess the impact of genetic modification on Saccharomyces cerevisiae yeast strains during the process of alcoholic fermentation, utilizing fig syrup. Multiple fermentations were carried out at various temperatures to evaluate the influence of genetic modifications on yeast strain efficiency. The study involved a wild-type yeast strain, W303, as a control, and two genetically modified strains, W_M4_533 and W_M4_558, sharing the same genetic background as the wild type. Notably, the genetic modifications in the Msn4p transcription factor involved the substitution of serine residues with alanine at positions 533 and 558, resulting in the development of psychrophilic or ethanol-resistant strains. Utilizing the R.F.G.C. method enabled the differentiation of the duration of alcoholic fermentation phases, providing insights correlated to the yeast cell life cycle. The values of rate constants (k) for each phase, conducted with both wild-type and genetically modified cells using RFGC, aligned with existing literature. Additionally, the calculation of activation energies for distinct phases revealed lower values for genetically modified strains compared to wild-type strains. This decrease in activation energies suggests enhanced efficiency in the alcoholic fermentation process for the genetically modified strains.

The research investigated the relationship between burnout syndrome and the variables of mental resilience and quality and enjoyment of life, in Greek private and public sector workers (N=112), with demographic differences. Data were collected through a structured questionnaire which was distributed in the form of an electronic Microsoft forms. The questionnaire contained demographic questions, the psychometric tool Burnout Assessment Tool version 2.0 (Schaufeli et al., 2019), the psychometric tool Brief Resilience Scale (BRS) (Smith et al., 2008), and the psychometric tool Quality of Life Enjoyment and Satisfaction Questionnaire (Q-LES-Q) (Endicott et al., 1993) which were used to measure the three variables examined by the research. For statistical analysis, Pearson and Spearman correlation coefficients were used to test the relationship between two quantitative variables, while linear regression analysis was used to find independent factors. The main research hypothesis was verified, finding a negative correlation between burnout and the variables of mental resilience and quality of life, while it was identified that employees experienced greater exhaustion and spiritual withdrawal compared to freelancers. Hypotheses regarding age, educational level, and public-private job data were not verified as there were no statistically significant differences in demographic results.