Here is shown method for the hydraulic solution of a looped gas-pipeline networks. Calculation of presented network is done according to principles of Hardy Cross method. The optimization was carried out by iteration of the pipes diameters, node consumptions are known and flow velocities through pipes have to stand below certain values. Accent is on determination of appropriate friction factor, and on selection of representative equation for natural gas flow under presented conditions in the network. Inappropriate usage of friction factor, equally as inappropriate usage of gas flow equation can lead to inaccurate final results. Here is shown new facts in comparison to previous calculation of gas distribution network in Kragujevac, Serbia which is done in 1994. After the implementation, measurements in situ have performed, and real measured values deviate from calculated. Causes for these errors are investigated, and improved and more accurate procedure is shown.

Pneumatic nebulizers (as variations based on the Collison nebulizer) have been widely used for producing fine aerosol droplets from a liquid material. The basic working principle of those nebulizers has been qualitatively described as utilization of the negative pressure associated with an expanding gas jet to syphon liquid into the jet stream, then to blow and shear into liquid sheets, filaments, and eventually droplets. Detailed quantitative analysis based on fluid mechanics theory is desirable, to gain in-depth understanding of the liquid aspiration mechanism among other aspects of the Collison nebulizer behaviour. The purpose of present work is to investigate the nature of negative pressure distribution associated with compressible gas jet flow in the Collison nebulizer by a computational fluid dynamics (CFD) analysis, using an OpenFOAM® compressible flow solver. The value of the negative pressure associated with a gas jet flow is examined by varying geometric parameters of the jet expansion channel adjacent to the outlet of jet orifice. Such an analysis can provide valuable insights into fundamental mechanisms for liquid aspiration, helpful for designing improved pneumatic atomizer in the Aerosol Jet® direct-write system for micro-feature, high-aspect-ratio material deposition

The main objective of this paper is to continue the development of activities of basic and applied research related to wind energy and to develop methods of optimal control to improve the performance and production of electrical energy from wind. A new control technique of Double fed induction generator for wind turbine is undertaken through a robust approach tagged nonlinear sliding mode control (SMC) with exponential reaching law control (ERL). The SMC with ERL proves to be capable of reducing the system chattering phenomenon as well as accelerating the approaching process. A nonlinear case numerical simulation test is employed to verify the superior performance of the ERL method over traditional power rate reaching strategy. Results obtained in Matlab/Simulink environment show that the SMC with ERL is more robust, prove excellent performance for the control unit by improving power quality and stability of wind turbine.

Leaf temperature (T_leaf) influences photosynthesis and respiration. Currently, there is a growing interest on including lianas in productivity models due to their increasing abundance, and their detrimental effects on net primary productivity in tropical environments. Therefore, understanding the differences of T_leaf between lianas and trees is important for future of forest on whole ecosystem productivity. Here we determined the displayed leaf temperature (T_d= T_leaf – ambient temperature) of several species of lianas and their host trees during ENSO and non-ENSO years to evaluate if the presence of lianas affects the T_d of their host trees, and if leaves of lianas and their host trees exhibit differences in T_d. Our results suggest that close to midday, the presence of lianas does not affect the T_d of their host trees; however, lianas tend to have higher values of T_d than their hosts across seasons, in both ENSO and non-ENSO years. Although lianas and trees tend to have similar physiological-temperature responses, differences in T_d could lead to significant differences in rates of photosynthesis and respiration based temperature response curves. Future models should thus consider differences in leaf temperature between these life forms to achieve robust predictions of productivity.

We propose a wave-like design on the surface of cathode channels (wave form cathode channels) to improve oxidant delivery to gas diffusion layers (GDLs) [1-2]. We performed experiments using PEMFCs combined with wave form surface design on cathodes. We varied the factors of the distance between wave-bumps (the Adhesive distance, AD), and the size of the wave-bumps (the Expansion ratio, ER). The ADs are 3, 4, and 5 times the size of the half-circle bump’s radius, and the ERs are 1/1.5, 1/2, and 1/3 times the channel’s height. We evaluated the performances of the fuel cells, and compared the current-voltage (I-V) relations. For comparison, we prepared PEMFCs with conventional flat-surfaced oxygen channels. Our aim in this work is to identify fuel cell operation by modifying the surface design of channels, and ultimately to find the optimal design of cathode channels that will maximize fuel cell performance.

Transport biofuels derived from biogenic material are used for substituting fossil fuels, thereby abating greenhouse gas (GHG) emissions. Numerous competing conversion options exist to produce biofuels, with differing GHG emissions and costs. In this paper analysis and modelling of the long-term development of GHG abatement and relative GHG abatement cost competitiveness between crop-based biofuels in Germany is carried out. Presently dominant conventional biofuels and advanced liquid biofuels were found not to be competitive compared to the substantially higher yielding options available: sugar beet based ethanol for the short to medium term least-cost option and Substitute Natural Gas (SNG) for the medium to long term. The competitiveness of SNG was found to depend highly on the emissions development of the power mix. Silage maize based biomethane was found competitive on a land area basis, but not on an energetic basis. Due to land limitations as well as cost and GHG uncertainty, a stronger focus on the land use of crop-based biofuels should be laid in policy.

Energy harvesting from wind turbines has been explored by researchers for more than a century from conventional turbines up to the latest bladeless turbines. Amongst these bladeless turbines, vortex bladeless wind turbine (VBT) harvests energy from oscillation of a turbine body. Due to the novelty of this science and the widespread researches around the world, one of the most important issues is to optimize and predict produced power. To enhance the produced output electrical power of VBT, the fluid-solid interactions (FSI) were analyzed to collect a dataset for predicting procedure. Long short-term memory (LSTM) method has been used to predict the produced power of VBT from the collected data. The reason of choosing LSTM from various artificial neural network methods is that the parameters of VBT study are all time- dependent and the LSTM is one of the most accruable algorithms for predicting time series data. In order to find the relationship between the parameter and the variables used in this research, a correlation matrix was presented. According to the value of 0.3 for the root mean square error (RMSE), a comparative analysis between the simulation results and its prediction shows that the LSTM method is very accurate for these types of research. Furthermore, the LSTM method has significantly reduced the computation time so that the prediction time of desired values has been reduced from an average of 2 and a half hours to two minutes. Also, one of the most important achievements of this study is to suggest a mathematical relation of VBT output power which helps to extend it in a different size of VBT with a high range of parameter variations.

Conservation Agriculture (CA) alters soil properties and microbial processes compared to conventional agriculture. These changes can affect soil-atmosphere greenhouse gas (GHG) fluxes. In this overview, we summarized the results of global literature and the gaps in measuring and understanding of GHG fluxes in CA systems and conventional agriculture. Some studies compared soil carbon sequestration and soil respiration in conservation agriculture and no-tillage system with conventional agriculture and the results were not consistent in all experiments. Interactions between CA pillars and soil factors such as soil moisture, temperature, texture can determine the rate of respiration rate and soil-atmosphere CO₂ fluxes. The majority of studies reported larger N₂O emissions in no-tillage treatment compared with conventional tillage while some other studies reported no difference between no-tillage and conventional tillage systems. In the majority of CA studies, there is lack of required information which is necessary to understand the mechanisms and processes that affect soil GHG fluxes. Determining factors like climate, amount of plant residues, soil type, crop types included in crop rotation and cover crops and duration of the study are not considered. Static chamber method was used for measuring soil-atmosphere GHG fluxes in the majority of studies. Spatial and temporal changes in GHG flux rates are high and missing part of highly episodic events by using static chamber method may result over- or under-estimation in flux balance calculation. Applying standard techniques for measuring continuous fluxes can help to calculating accurate GHG balance.

This paper presents the super-twisting algorithm (STA) direct power control (DPC) scheme for the control of active and reactive powers of grid-connected DFIG. Simulations of 5 KW DFIG has been presented to validate the effectiveness and robustness of the proposed approach in the presence of uncertainties with respect to vector control (VC). The proposed controller schemes with fixed gains are effective in reducing the ripple of active and reactive powers, effectively suppress sliding-mode chattering and the effe This paper presents a comparative study of two approaches for the direct power control (DPC) of doubly-fed induction generator (DFIG) based on wind energy conversion system (WECS). Vector Control (VC) and Sliding Mode Control (SMC). The simulation results of the DFIG of 5 KW in the presence of various uncertainties were carried out to evaluate the capability and robustness of the proposed control scheme. The (SMC) strategy is the most appropriate scheme with the best combination such as reducing high powers ripple, diminishing steady-state error in addition to the fact that the impact of machine parameter variations does not change the system performance. cts of parametric uncertainties not affecting system performance.

The use of wind energy has been developing fast over the last years. The global cumulative wind power capacity increased by 10.5% in 2019, most of which comes from onshore wind farms. One of the consequences of this continuous increase is the use of land for onshore wind farms. There are already cases worldwide where lack of well-established plans and strategies have caused delays in projects. The need for efficiently using land for wind farms will be mandatory in the short term. In this work, we present a numerical analysis to evaluate wind farm land-use. By defining the ratio between mechanical output power over an area as a parameter called land-use ratio, this work focused on comparing several cases of aligned and staggered layouts. Mechanical output power was estimated using a validated code based on Blade Element Momentum code, and the wake velocities and wake interaction effects were estimated using a validated wind turbine CFD model. In terms of output power, staggered designs are more efficient than aligned designs. However, the results showed that even though staggered designs produced higher output power, aligned farms with tight lateral spacing could be as efficient as staggered ones in terms of land-use but using fewer turbines. In summary, tightly aligned designs should be a tendency in the future towards efficient use of land in wind farms.

Gas flaring is a disposal process widely used in the oil extraction and processing industry. It consists in the burning of unwanted gas at the tip of a stack and due to its thermal characteristic and the thermal emission it is possible to observe and to quantify it from space. Spaceborne observations allows us to collect information across regions and hence to provide a base for estimation of emissions on global scale. We have successfully adapted the Visible Infrared Imaging Radiometer Suite (VIIRS) Nightfire algorithm for the detection and characterisation of persistent hot spots, including gas flares, to the Sea and Land Surface Temperature Radiometer (SLSTR) observations on-board the Sentinel- satellites. A hot event at temperatures typical of a gas flare will produce a local maximum in the night-time readings of the shortwave and mid-infrared (SWIR and MIR) channels of SLSTR. The SWIR band centered at 1.61 mmis closest to the expected spectral radiancemaximumand serves as the primary detection band. The hot source is characterised in terms of temperature and area by fitting the sum of two Planck curves, one for the hot source and another for the background, to the radiances from all the available SWIR, MIR and thermal infra-red channels of SLSTR. The flaring radiative power is calculated from the gas flare temperature and area. Our algorithm differs from the original VIIRS Nightfire algorithm in three key aspects: (1) It uses a granule-based contextual thresholding to detect hot pixels, being independent of the number of hot sources present and their intensity. (2) It analyses entire clusters of hot source detections instead of individual pixels. This is arguably a more comprehensive use of the available information. (3) The co-registration errors between hot source clusters in the different spectral bands are calculated and corrected. This also contributes to the SLSTR instrument validation. Cross-comparisons of the new gas flare characterisation with temporally close observations by the higher resolution German FireBIRD TET-1 small satellite and with the Nightfire product based on VIIRS on-board the Suomi-NPP satellite show general agreement for an individual flaring site in Siberia and for several flaring regions around the world. Small systematic differences to VIIRS Nightfire are nevertheless apparent. Based on the hot spot characterisation, gas flares can be identified and flared gas volumes and pollutant emissions can be calculated with previously published methods.

Gas turbine engines are widely used in various industries such as aviation, power generation, and marine propulsion due to their high efficiency and reliability. The combustion chamber of a gas turbine engine design contains a number of elements, including as the chamber's size and form, the fuel injection system, the ignition system, and the cooling system and it plays a critical role in the performance and efficiency of the engine. This research discusses the fabrication of a combustion chamber model for a gas turbine engine. The aim of this research is to develop a combustion chamber that is cost-effective, easily available, and can be fabricated in less time. The research covers the different types of combustion chambers used in gas turbine engines and compares their advantages and disadvantages. It then selects the best type of combustion chamber for the gas turbine engine based on its cost, availability, and fabrication time, Efficiency and high power to fuel ratio. The report also describes the fabrication process involved, including the techniques and materials used, along with safety precautions and environmental protection measures. Lastly, the research suggests future improvements and potential applications for the fabricated combustion chamber model.

In this paper, a non-destructive test to diagnose wear of blade´s compressor of a gas turbine is reported. Gas turbine was operating in Campeche City, Mexico, in a very aggressive environment, where the entry of solid particles is unavoidable. The objective was to reduce cost of maintenance in this equipment. Analysis on a blade of gas turbine was performed, which was in operation on an offshore platform. Compressor blade was exposed to a severe damage by the impact of particles and environmental pollutants such as salts, sands and sulphurs. In first stage of this analysis, a visual inspection with a borescope was performed, which has the ability to illuminate dark internal areas, with a bright light for visual examination and/or make a photographic reproduction in semi-annual maintenance cycles. Images analysis was used to determine the typical failure modes. In a second stage, a tribological characterization was carried out. Chemical composition of the material of blades was obtained. Scanning electron microscopy (SEM) was used to measure roughness and evaluate degradation of surfaces of blades after 30,000 service hours. The points, where peak stresses were calculated, correspond to those places in witch corrosion and some irregular scratches similar to plowing action, was observed. These are the points in which failures take place. Results showed wear modes were originated by a severe stinging action. Also, large craters, similar to those observed in solid particle erosion, were developed by at normal impact. In the same way it could be found some localized areas with a witch corrosion and irregular scratches similar to plowing action, was observed. These are the points in which failures take place.

Fuel gas network (FGN) synthesis is a systematic method for reducing fresh fuel consumption in a chemical plant. In this work, we address the synthesis of fuel gas network using block superstructure originally proposed for process design and intensification (Demirel et.al. [1]). Instead of a classical source-pool-sink superstructure, we consider a superstructure with multiple feed and product streams. These blocks interact with each other through direct flows that connect a block with its adjacent blocks and through jump flows that connect a block with all blocks. The blocks with feed streams are viewed as fuel sources and the blocks with product streams are regarded as fuel sinks. Addition blocks can be added as pools when there exists intermediate operations among 9 source blocks and sink blocks. These blocks can be arranged in a I × J two-dimensional grid with I = 1 for problems without pools, or I = 2 for problems with pools. J is determined by the maximum number of pools/sinks. With this representation, we formulate fuel gas network synthesis problem as a mixed-integer nonlinear (MINLP) problem to optimally design a fuel gas network with minimal total annul cost. We present a real-life case study from LNG plant to demonstrate the capability of the proposed approach.

Coalbed Methane(CBM) production enhancement for single wells is a big problem to CBM industrialization. Low production is due to insufficient gas generation by thermogenic. Luckily, Biogenic gas was found in many areas and its supply is assumed to improve coalbed methane production. Therefore, microbial simulation experiment will demonstrate the effectiveness of the assumption. From microbial simulation experiment on different coal ranks, it is found that microbes can use coals to produce biogas under laboratory conditions. With different temperatures for different experiments, it turns out that the gas production at 35 ℃ is greater than that at 15℃,indicating that 35℃ is more suitable for microbes to produce gas. According to quantitative experiments, adding exogenous nutrients or exogenous bacteria can improve CBM production. Moreover, the production enhancement ratio can reach up to 115% under the condition of adding exogenous bacterial species, while the ratio for adding nutrients can be up to 144%.

The crack in the blade is the most common type of fatigue damage for Francis turbines. However, the crack sometimes is difficult to be detected in time using the current monitoring system even when the crack is very large. To better monitor the crack, it is imperative to research the effect of a crack on the dynamic behavior of a Francis turbine. In this paper, the dynamic behavior of a Francis turbine runner model with a crack was researched numerically. The intact numerical model was first validated by the experimental data available. Then, a crack was created at the intersection line between one blade and the crown. The change in dynamic behavior with increasing crack length was investigated. Crack-induced vibration localization theory was used to explain the dynamic behavior changes due to the crack. Modal analysis showed that the adopted theory could basically explain the modal behavior change due to the crack. The FFT results of the modal shapes and the localization factors (LF) were used to explain the forced response changes due to the crack. Based on the above analysis, the challenge of crack monitoring was analyzed. This research can also provide some references for more advanced monitoring technologies.

Shale gas reservoirs (SGR) are important replacements for conventional energy resources and have been widely exploited by hydraulic fracturing technologies. On the one hand, due to the inherent ultra-low permeability and porosity, there is stress sensitivity in the reservoirs generally. On the other hand, hydraulic fractures and the stimulated reservoir volume (SRV) generated by the massive hydraulic fracturing operation have contrast properties with the original reservoirs. These two phenomena bring huge challenges in SGR transient pressure analysis. Although some works in the literatures have been done on the transient pressure analysis of multi-fractured horizontal wells in SGR, unfortunately, none of them has taken the stress sensitivity and spatially varying permeability of SRV zone into consideration simultaneously. To fill this gap, this paper first idealizes the SGR to be four linear composite regions. What’s more, SRV zone is further divided into sub-sections on the basis of non-uniform distribution of proppant within SRV zone which easily yields spatially varying permeability away from the main hydraulic fracture. The stress sensitivity is characterized by the varying permeability depended on the pore pressure. By means of perturbation transformation and Laplace transformation, an analytical multi-linear flow model (MLFM) is obtained and validated by the comparison with the previous model. On the basis of our model, the flow regimes are identified and the sensitivity analysis of critical parameters are conducted to further understand the transient pressure behaviors. The research results provided by this work are of significance for well test interpretation and production performance analysis of SGR.

Atmospheric stability affects wind turbine wakes significantly. High-fidelity approaches such as large eddy simulations (LES) with the actuator line (AL) model which predicts detailed wake structures, fail to be applied in wind farm engineering applications due to its expensive cost. In order to make wind farm simulations computationally affordable, this paper proposes a new actuator disk model (AD) based on the blade element method (BEM) and combined with Reynolds-averaged Navier–Stokes equations (RANS) to model turbine wakes under different atmospheric stability conditions. In the proposed model, the upstream reference velocity is firstly estimated from the disk averaged velocity based on the one-dimensional momentum theory, and then is used to evaluate the rotor speed to calculate blade element forces. Flow similarity functions based on field measurement are applied to limit wind shear under strongly stable conditions, and turbulence source terms are added to take the buoyant-driven effects into consideration. Results from the new AD model are compared with field measurements and results from the AD model based on the thrust coefficient, the BEM-AD model with classical similarity functions and a high-fidelity LES approach. The results show that the proposed method is better in simulating wakes under various atmospheric stability conditions than the other AD models and has a similar performance to the high-fidelity LES approach however in much lower computational cost.

In this work, we develop a self-consistent physical model of bubbles in a gas solid two-phase flow. Using the Peng-Robonson state equation and a detailed specific heat ratio equation of bubbles, we obtain the kinetic equations of the bubbles on the basis of the Ergun equation, thermodynamic equations, and kinetic equations. It is found that the specific heat ratio of bubbles in such systems strongly depends on bubble pressures and temperatures, which play an important role in the characteristics of the bubbles. The theoretical studies show that with increasing height in the systems, the gas flow rate shows a downward trend. Moreover, the larger particles in the gas solid flows are, the greater the gas velocity is. The bubble sizes increase with the increasing heights of the gas solid systems, and then decrease. The bubble velocity is affected by the gas velocity and the bubble size, which gradually increase and eventually quasi-stabilize. This shows that gas and solid phases in a gas solid two-phase flow interact with each other and a self-consistent system comes into being. The theoretical results have exhibited important value as a guide for understanding the properties and effects of bubbles in gas solid two-phase flows.

A laser-based hydrogen (H₂) sensor using wavelength modulation spectroscopy (WMS) was developed for contactless measurements of molecular hydrogen. The sensor uses a distributed feedback (DFB) laser to target the H₂ quadrupole absorption line at 2121.8 nm. The H₂ absorption line exhibits weak collisional broadening and strong collisional narrowing effects. Both effects were investigated by comparing measurements of the absorption linewidth with detailed models using different line profiles that include collisional narrowing effects. The collisional broadening and narrowing parameters were determined for pure hydrogen as well as for hydrogen in nitrogen and air. Performance of the sensor was evaluated and the sensor applicability for H₂ measurements in a range of 0- 10 %v of H₂ was demonstrated. A precision of 0.02 %v was achieved with 1 meter of absorption pathlength (0.02 %v∙m) and 1 s of integration time. For the optimum averaging time of 20 s a precision of 0.005 %v∙m was achieved. A good linear relationship between H₂ concentration and the sensor response was observed. A simple and robust transmitter-receiver configuration of the sensor allows in-situ installations in harsh industrial environments.

In this contribution, a method based on a solid solution theory of clathrate hydrate for multiple cage occupancy, host lattice relaxation and guest-guest interactions has been presented to estimate hydrate formation conditions of binary and ternary gas mixtures. We have performed molecular modeling of structure, guest distribution, and hydrate formation conditions for the CO₂ + CH₄, and CO₂ + CH₄ + N₂ gas hydrates. In all considered systems with and without N₂, at high and medium content of CO₂ in the gas phase we have found that CO₂ is more favorable to occupy clathrate hydrate cavities than CH₄ or N₂. Addition of N₂ to the gas phase increases ratio concentration CO₂ in compressing with concentration CH₄ in clathrate hydrates and makes gas replacement more effective. The mole fractions of CO₂ in CO₂ + CH₄ + N₂ gas hydrate rapidly increases with the growth of its content in the gas phase. And the formation pressure of CO₂ + CH₄ + N₂ gas hydrate rises in comparison with the formation pressure of CO₂ + CH₄ gas hydrate. Obtained results agree with the known experimental data for simple CH₄, CO₂ gas hydrates and mixed CO₂ + CH₄ gas hydrate.

The article discusses the validation process of a certain method of balancing gas contained in the pore space of rocks. The validation was based upon juxtaposition of the examination of rocks' porosity and the effects of comminution in terms of assessing the possibility of opening the pore space. The tests were carried out for six dolomite samples taken from different areas of the 'Polkowice-Sieroszowice’ copper mine in Poland. Before the rock material was ground, it was examined using the porosimetric method and subsequently subjected to the SEM analysis. After grinding, the research material was subjected to the granulometric analysis. Prior to the grinding process, the rocks' porosity fell in the range of 0.3-14.8%, while the volume of the open pores was included in the 0.01-0.06 cm3/g range. The research material was also characterized by inhomogeneous distribution of the pore volume. The grinding process was performed using an original device – the GPR analyzer. The ground samples were characterized by similar particle size distribution and mean diameters D_3.2 of about 4.0-4.5 µm. The SEM analysis revealed pores of various size and shape on the surface of the rock cores, while at the same time demonstrating lack of pores following the grinding process. The grain size distribution curves were compared with the cumulative pore volume curves of the cores before grinding. The resulting intersection points of both curves were seen as testifying to the presence of openings in the rock pores and release of the accumulated gas. The opening percentage of the pore space was associated with the coordinates of the curves' intersections. In order to confirm the argument put forward in this paper – i.e. that comminution of a rock to grains of a size comparable with the size of the rock's pores results in the release of gas contained in the pore space – the amount of gas released as a result of the comminution process was studied. The results of gas balancing demonstrated that the pore space of the investigated dolomites was filled with gas in amounts from 3.19 cm3/kg to 45.86 cm3/kg. The obtained results of the rock material comminution to grains comparable – in terms of size – to the size of the pores of investigated rocks, along with asserting the presence of gas in the pore space of the studied dolomites, were regarded as a proof that the method of balancing gas in rocks via rock comminution is correct.

Metal oxide p-n heterojunction nanofibers (NFs) are among the most promising approaches to enhancing the efficiency of gas sensors. In this paper, we report the preparation of a series of p-NiO-loaded n-ZnO NFs, namely (1 − x) ZnO-xNiO (x = 0.03, 0.05, and 0.1 wt%), for hydrogen gas sensing experiments. Samples were prepared through the electrospinning technique followed by a calcination process. The sensing experiments showed that the sample with 0.05 wt% NiO loading resulted in the highest sensing performance at an optimal sensing temperature of 200 °C. The sensing mechanism is discussed in detail and contributions of the p-n heterojunctions, metallization of ZnO and catalytic effect of NiO on the sensing enhancements of an optimized gas sensor are analyzed. This study demonstrates the possibility of fabricating high-performance H₂ sensors through the optimization of p-type metal oxide loading on the surfaces of n-type metal oxides.

There is great importance and need of improving existing carbon materials fabrication methods. As such, this work proposes to discuss, interrogate, and propose viable hydrothermal, solvothermal, and other advanced carbon materials synthetic methods. The advanced carbon materials to be interrogated will include the synthesis of carbon dots, carbon nanotubes, nitrogen/titania-doped carbons, graphene quantum dots, and their nanocomposites with solid/polymeric/metal oxide supports. This will be done with special mind to microwave-assisted solvothermal and hydrothermal synthesis due to their favourable properties such as rapidity, low cost, and green/environmentally-friendliness. Thus, these methods are important during the current and future synthesis and modification of advanced carbon materials for application in energy, gas separation, sensing, and water treatment. Simultaneously, the work will pay special cognizance to methods reducing the fabrication costs and environmental impact while enhancing the properties as a direct result of the synthesis methods. As a direct result, the expectation is to impart a significant contribution to the scientific body of work regarding the improvement of the said fabrication methods.

This paper presents a methodology for predictive and prescriptive analytics of complex engineering systems. The methodology is based on a combination of physics-based and data-driven modeling using machine learning techniques. Combining these approaches results in a set of reliable, fast, and continuously updating models for prescriptive analytics. The methodology is demonstrated with a case study of a jet-engine power plant preventive maintenance and diagnostics of its flame tube.

The Life Cycle Analysis (LCA) was used to assess the impact of biomethane plant of the “La Católica” in Pedregal-Majes-Arequipa farm, fed with cow manure and holding a production of 60 Nm3/day of purified biogas. Life cycle inventory, impact assessment and interpretation were performed. The functional unit established was 1 MJ of energy produced; the study was modeled with SimaPro software, Ecoinvent Database and ReCiPe Midpoint (H) impact assessment methodology, according to the impact categories of climate change and fossil resource depletion. The impact analysis was limited to the Well to Tank (WTT) approach, which involves feedstock transport, substrate mixed, anaerobic digestion, biogas purification, storage and injection of the fuel into transport vehicles. The digestion process generated the highest amount of CO2 emissions (1.79E-02 kg CO2 eq/MJ-biomethane) and the highest depletion of fossil resources (6.58E-03 kg oil eq/MJ-biomethane), compared to the other fuel production, due to energy consumption and transport infrastructure. Biomethane was then compared to fossil fuels, resulting in natural gas generating the least amount of CO2 emissions, followed by diesel and finally biomethane. For the fossil resource depletion category, biomethane presented the lowest amount of fossil fuel consumption (1.37E-02 kg oil eq/MJ-biomethane), followed by natural gas and diesel.

Accent is on determination of appropriate friction factor of the pipes and on selection of the representative equation for water or natural gas flow which is valuable for existing conditions in the looped network of pipelines. Note that in a municipal gas pipeline, natural gas can be treated as incompressible fluid (liquid) i.e. as water or oil. Even under this circumstance, calculation of water pipelines cannot be literary copied and applied for calculation of gas pipelines. Inappropriate friction factor, equally as e.g. inappropriate usage of water flow equations for calculation of gas networks can lead to inaccurate final results. Few iterative methods for determining the optimal hydraulic solution of water- and gas- looped pipeline networks, such as, Hardy Cross, modified Hardy Cross, node-loop method, node and M.M. Andrijashev method, will be shown. Speed of convergence will be compared and discussed using a simple network with three loops.

Oleylamine capped WS2 nanostructures were successfully formed at 320 °C via a relatively simple colloidal route. SEM and TEM analyses showed that the 3D nanoflowers that were initially formed disintegrated into 2D nanosheets after prolonged incubation. XPS and XRD analyses confirmed oxidation of WS2 into WO3. Sensors based on these oleylamine capped WS2 nanoflowers and nanosheets still showed a change in electrical response towards various concentrations of NH3 vapour at room temperature in a 25% relative humidity background despite the oxidation. The nanoflowers exhibited n-type response while the nanosheets displayed a p-type response towards NH3 exposure. The nanoflower based sensors showed better response to NH3 vapour exposure than the nanosheets. The sensors showed a good selectivity towards NH3 relative to acetone, ethanol, chloroform and toluene. Meanwhile, a strong interference of humidity to the NH3 response was displayed at high relative humidity levels. The results demonstrated that oleylamine limited the extent of oxidation of WS2 nanostructures. The superior sensing performance of the nanoflowers can be attributed to their hierarchical morphology which enhances the surface area and diffusion of the analyte.

Tributyltin (TBT) is one of the most toxic anthropogenic compounds introduced into the marine environment. Despite its global ban in 2008, TBT is still a problem of great concern due to its high affinity for particulate matter, providing a direct and potentially persistent route of entry into benthic sediments. Bioremediation strategies may constitute an alternative approach to conventional physicochemical methods, benefiting from the microorganism’s potential to metabolize anthropogenic compounds. In this work, a simple, precise and accurate static headspace gas chromatography method was developed to investigate the ability of TBT degrading microbes in sedimentary microcosms over a period of 120 days. The proposed method was validated for linearity, repeatability, accuracy, specificity, limit of detection and limit of quantification. The method was subsequently successfully applied for the detection and quantification of TBT and degrading compounds in sediment samples on day 0, 30, 60, 90 and 120 of the experiment employing the principles of green chemistry. On day 120 the concentration of TBT remaining in the microcosms ranged between 91.91 ng/g wet wt for the least effective microbial inoculant to 52.73 ng/g wet wt for the most effective microbial inoculant from a stating concentration of 100 ng/g wet wt.

This paper reassesses the detrimental effect on fatigue performance due to thicker sections based on extensive fatigue strength test database, taken from research program worldwide over the past half of a century in offshore oil & gas and renewable industry. The data entries in the database have been evaluated to ensure its data integrity. Statistical analyses on these S-N data are performed with or without the thickness correction at different exposure level to corrosive environment, in order to re-evaluate the suitability of current standards in regard to the thickness effect. The study has concentrated on T-joint, transverse butt welded joint and tubular joint as these are the most commonly used joint types in the offshore wind industry. The analysis indicates general agreement of fatigue strength with the thickness effects in current standard for in air conditions but great conservatism for corrosive environment.

The development of an underground gas storage (UGS) project and its subsequent management must ensure technical feasibility, commercial value and long-term efficiency. The UGS industry has borrowed much of its knowledge from other disciplines (primarily oil and gas reservoir engineering), but it has also developed its own technology. This paper provides a methodological approach based on current practices and available methods for designing and safely operating a UGS (including the so-called “delta-pressure” option to enhance UGS performance) and highlights what is special in UGS compared to oil and gas reservoirs.

In this work, a tailored extreme learning machine (ELM) algorithm to enhance the overall robustness of gas analyzer based on the tunable diode laser absorption spectroscopy (TDLAS) method is presented. The ELM model is tailored through activation function selection, input weight and bias searching, and cross validation method to address the analyzer robustness issues for industrial process analysis field application. The two particular issues are the inaccurate gas concentration measurement caused by the process gas background components variation, and the inaccurate spectra shift calculation caused by spectral interference. By using our algorithm, the concentration error is reduced by one order of magnitude over a much larger stream pressure and component range compared with that obtained by classical least square (CLS) fitting methods based on reference curves. Additionally, it is shown that with our algorithm, the wavelength shift accuracy is improved to less than 1 count over 1000 counts spectra length. In order to test the viability of our algorithm, a trace ethylene (C₂H₄) TDLAS analyzer with coexisting methane was implemented, and its experimental measurements support analyzing robustness enhancement effect.

It is often difficult to extract data on material and energy wates and related costs in the value chain of conventional production units. Many organizations are not fully aware of the actual cost of material and energy waste. For this purpose, advanced costing methods should be used. This study uses material and energy flow cost accounting to determine material costs, losses, and waste management. The case study of this research is the construction of turbine blades in Iran Power Plant Company. In this study, using the extracted data, the construction costs of turbine blades have been studied. The conventional method of making a turbine blade is the machining method, which we will see has a huge amount of wastes of materials and energy. By studying different methods, we will find that there is an alternative method called forging, which reduces losses and costs. Finally, the costs of the two methods are compared. Engineering economics techniques have also been used to compare two methods on a long-term planning horizon.

Indoor air quality and public health have always been an area of prime interest across the globe. The significance of low-cost air quality sensing and indoor public health practices spikes during the time of pandemic and epidemics when indoor air pollution becomes a threat to living beings especially human beings. Indoor diseases are hard to diagnose if they are due to the indoor environmental conditions. A major challenge was observed in establishing a baseline between the indoor air quality sensors and associated diseases. In this work, 10,000+ articles from top literature databases were reviewed using bibliometric analysis to formulate indoor air quality sensors and diseases correlation rubrics to critically review 500+ articles. A set of 200+ articles were selected based on for detailed study based on seven bibliometric indices for publications that used WHO, NIH, US EPA, CDC, and FDA defined principles. This review has been conducted to assist end-users, public health facilities, state agencies, researchers, scientists and air quality protection agencies.

Hydrogen plays a key role in the transition to a carbon-free economy. One of the areas of hydrogen use is the substitution of hydrocarbon fuel in gas turbine engines and power plants. This review article discusses the features of hydrogen combustion and their influence on the characteristics of combustion chambers in comparison with methane. The paper presents both the results of a study of pure hydrogen or methane and methane-hydrogen mixtures with different hydrogen content. Among the main features, it is worth noting a smaller ignition delay time and higher laminar flame speed with a shift in its maximum value to a rich mixture, which significantly affects on flashback inside burners premixer, especially at elevated air temperatures. Another feature is the increased temperature of the flame, which can lead to an increase in the rate of nitrogen oxides formation. However, wider combustion concentration ranges contribute to the stable combustion of hydrogen at temperatures lower than those of methane. Along with this, it was shown that even at the same adiabatic temperature, more nitrogen oxides are formed in a hydrogen flame than in a methane flame, which indicates an additional mechanism for NOx formation in addition to the Zeldovich mechanism. The article also summarizes some of the results of a study on the effect of hydrogen on the occurrence of thermoacoustic instability, which depends on the initial nature of pulsations during methane combustion. The presented data will be useful both to engineers who are engaged in solving the problems of designing hydrogen combustion devices, and to scientists in this field of study.

Doubly Fed Induction Generator (DFIG) has a stator winding directly coupled with grid. Whereas, rotor winding is connected via a fault-prone back to back power converters. DFIG is known to be vulnerable to the grid faults. In early times, when a fault occurred, these generators were required to disconnect from the grid to secure the generator and power converters. However, due to the increased penetration of wind turbines into the power system, grid operators demanded that the wind turbines remain connected to the grid, as disconnecting them would further disrupt the grid. When a fault at the grid terminal occur, a high stator current is induced which further result in high rotor current. This current will trigger the DC-link voltage to rise. This high currents and DC-link voltage will cause harm to the converters. Thus, in this paper work, the crowbar protection system is employed for protecting the converters against excess energy. Furthermore, the analysis of DFIG is rendered by integrating the crowbar protection with the Battery Energy Storage System (BESS) for a much effective outcome in enhancing machine to drive the fault. MATLAB-Simulink software is used for modeling and simulation. All system parameters are obtained from ADAMA-II Wind Farm.

The assessment of caprock integrity for underground storage of CO2 and/or enhanced oil recovery (EOR) systems is a multiscale endeavor. Caprock sealing behavior depends on coupled processes that operate over a broad range of length and time scales including nanoscale heterogeneity in capillary and wettability properties to depositional heterogeneity that is basin wide. Larger-scale sedimentary architecture, fractures, and faults can govern properties of potential “seal-bypass” systems that may be difficult to assess. We present a multiscale investigation of geologic sealing integrity of the caprock system that overlies the Morrow B sandstone reservoir, Farnsworth Unit, Texas, USA. The Morrow B sandstone is the target geologic unit for an on-going combined CO2 storage–EOR project by the Southwest Regional Partnership on Carbon Sequestration (SWP). Methods and/or data encompass small-to-large scales, including: petrography using electron and optical microscopy; mercury porosimetry; core examinations of sedimentary architecture and fractures; well logs; a suite of geomechanical testing; and a noble gas profile through sealing lithologies into the reservoir, as preserved from fresh core. The combined data set allows a comprehensive examination of sealing quality by scale, by primary features that control sealing behavior, and an assessment of sealing behavior over geologic time.

A modified free-wake vortex ring model is proposed to compute the dynamics of a floating horizontal-axis wind turbine. The model is divided into two parts. The near wake model uses a blade bound vortex model and trailed vortex model, which is developed based on vortex filament method. By contrast, the far wake model is based on the vortex ring method. The proposed model is a good compromise between accuracy and computational cost, for example when compared with more complex vortex methods. The present model is used to assess the influence of floating platform motions on the performance of a horizontal-axis wind turbine rotor. The results are validated on the 5MW NREL rotor and compared with other aerodynamic models for the same rotor subjected to different platform motions. It was found that the results from the proposed method are more reliable than the results from BEM theory especially at small angles of attack in the region of low wind speeds, on the one hand, and high wind speeds with blade pitch motions, on the other hand. And also the proposed method is less time consuming and has similar accuracy when comparing with more advanced vortex based methods.

1) Background: Recently, illegal abuse of γ-hydroxybutyric acid (GHB) has increased in drug-facilitated crimes, but determination of GHB exposure and intoxication is difficult due to rapid metabolism of GHB. Its biochemical mechanism has not been completely investigated. And metabolomic study by polyamine profile and pattern analyses was not performed in rat urinefollowing intraperitoneal injection with GHB. 2) Methods: Polyamine profiling analysis by gas chromatography-mass spectrometry combined with star pattern recognition analysis was performed in this study. Multivariate statistical analysis was used to evaluate discrimination between control and GHB administration groups. 3) Results: Six polyamines were determined in control, single and multiple GHB administration groups. Star pattern showed distorted hexagonal shapes with characteristic and readily distinguishable patterns for each group. N¹-Acetylspermine (p < 0.001), putrescine (p <0.006), N¹-acetylspermidine (p <0.009), and spermine (p < 0.027) were significantly increased in single administration group but were significantly lower in the multiple administration group than in the control group. N¹-Acetylspermine was the main polyamine for discrimination between control, single and multiple administration groups. Spermine showed similar levels in single and multiple administration groups. 4) Conclusions: The polyamine metabolic pattern was monitored in GHB administration groups. N¹-Acetylspermine and spermine were evaluated as potential biomarkers of GHB exposure and addiction.

The Smart Energy Research Lab (SERL) Observatory dataset described here comprises half-hourly and daily electricity and gas data, SERL survey data, Energy Performance Certificate (EPC) input data and 24 local hourly climate reanalysis variables from the European Centre for Medium-Range Weather Forecasts (ECMWF) for over 13,000 households in Great Britain (GB). Participants were recruited in September 2019, September 2020 and January 2021 and their smart meter data are collected from up to one year prior to sign up. Data collection will continue until at least August 2022, and longer if funding allows. Survey data relating to the dwelling, appliances, household demographics and attitudes was collected at sign up. Data are linked at the household level and UK-based academic researchers can apply for access within a secure virtual environment for research projects in the public interest. This is a data descriptor paper describing how the data was collected, the variables available and the representativeness of the sample compared to national estimates. It is intended as a guide for researchers working with or considering using the SERL Observatory dataset, or simply looking to learn more about it.

The interest on the use of renewable energy resources is increasing, especially towards wind and hydro powers, which should be efficiently converted into electric energy via suitable technology tools. To this aim, self--tuning control techniques represent viable strategies that can be employed for this purpose, due to the features of these nonlinear dynamic processes working over a wide range of operating conditions, driven by stochastic inputs, excitations and disturbances. Some of the considered methods were already verified on wind turbine systems, and important advantages may thus derive from the appropriate implementation of the same control schemes for hydroelectric plants. This represents the key point of the work, which provides some guidelines on the design and the application of these control strategies to these energy conversion systems. In fact, it seems that investigations related with both wind and hydraulic energies present a reduced number of common aspects, thus leading to little exchange and share of possible common points. This consideration is particularly valid with reference to the more established wind area when compared to hydroelectric systems. In this way, this work recalls the models of wind turbine and hydroelectric system, and investigates the application of different control solutions. The scope is to analyse common points in the control objectives and the achievable results from the application of different solutions. Another important point of this investigation regards the analysis of the exploited benchmark models, their control objectives, and the development of the control solutions. The working conditions of these energy conversion systems will be also taken into account in order to highlight the reliability and robustness characteristics of the developed control strategies, especially interesting for remote and relatively inaccessible location of many installations.

The development of sensors for monitoring Carbon Monoxide (CO) in a large range of temperature is of crucial importance in areas as monitoring of industrial processes or personal tracking using smart objects. Devices integrating GaN/Ga₂O₃ core/shell nanowires (NWs) is a promising solution allowing combining the high sensitivity of the electronic properties to the states of GaN-core surface; and the high sensitivity to CO of Ga₂O₃-shell. Because the performances of sensors primarily depend on the material properties composing the active layer of the device, it is essential to control these properties and in first time its synthesis. In this work, we investigate the synthesis of GaN/Ga₂O₃ core-shell NWs with a special focus on the formation of the shell. The GaN NWs grown by Plasma-assisted molecular beam epitaxy, are post-treated following thermal oxidation to form Ga₂O₃-shell surrounding the GaN-core. We establish that the Ga₂O₃-shell thickness can be modulated from 1 up to 14 nm by changing the oxidation conditions, and follows the diffuse-controlled reaction. By combining XRD-STEM and EDX analysis, we also demonstrate that the oxide shell formed by thermal oxidation is crystalline and presents the β-Ga₂O₃ crystalline phase, and is synthesized in epitaxial relationship with the GaN-core.

During the extraction of hard coal in Polish conditions, methane is emitted, which is referred to as mine gas. As a result of the desorption of methane, a greenhouse gas is released from coal seams. In order to reduce atmospheric emissions, methane from coal seams is captured by a methane drainage system. On the other hand, methane, which has been separated into underground mining excavations, is discharged into the atmosphere with a stream of ventilation air. For many years, Polish hard coal mines have been capturing methane to ensure the safety of the crew and the continuity of mining operations. As a greenhouse gas, methane has a significant potential, as it is more effective at absorbing and re-emitting radiation than carbon dioxide. The increase in the amount of methane in the atmosphere is a significant factor influencing global warming, however, it is not as strong as the increase in carbon dioxide. Therefore, in Polish mines, the methane-air mixture captured in the methane drainage system is not emitted to the atmosphere, but burned as fuel in systems, including cogeneration systems, to generate electricity, heat and cold. However, in order for such use to be possible, the methane-air mixture must meet appropriate quality and quantity requirements. The article presents an analysis of changes in selected parameters of the captured methane-air mixture from one of the hard coal mines in the Upper Silesian Coal Basin in Poland. The paper analyses the changes in concentration and size of the captured methane stream through the methane capturing system. The gas captured by the methane drainage system, as an energy source, can be used in cogeneration, when the methane concentration is greater than 40%. Considering the variability of CH4 concentration in the captured mixture, it was also indicated which pure methane stream must be added to the gas mixture in order for this gas to be used as a fuel for gas engines. The balance of power of produced electric energy in gas engines is presented. Possible solutions ensuring constant concentration of the captured methane-air mixture are also presented.

Recent studies have reported shallow and deep seep areas offshore Mocha island. Gas hydrate occurrences along the Chilean margin could explain seeps presence. Gas phases (gas hydrate and free gas) and geothermal gradients were estimated analysing two seismic sections. Close to Mocha island (up to 20 km) were detected high (up to 1900 m/s) and low (1260 m/s) velocities associated with high gas hydrate (up to 20 % of total volume) and free gas (up to 1.1% of total volume) concentrations respectively. These values are in agreement with a variable and high geothermal gradient (65 to 110 °C/km) related to high supply deep fluids canalised by faults and fractures. Faraway from Mocha island (more than 60 km), free gas concentrations decrease to 0.3 % of total volume and low geothermal gradient (from 35 to 60 °C/km) are associated with low fluids supply. Finally, we propose gas hydrate dissociation processes as the main supply source for seeps in the vicinity of Mocha island. These processes can be triggered by ancient sliding reported in literature.

For the past few decades, researchers have been intrigued with glassy polymers, which have applications ranging from gas separations to corrosion protection to drug delivery systems. The techniques employed to examine the sorption and diffusion of small molecules in glassy polymers are the subject of this review. Diffusion models in glassy polymers are regulated by Fickian and non-Fickian diffusion, with non-Fickian diffusion being more prevalent. The characteristics of glassy polymers are determined by sorption isotherms, and different models have been proposed in the literature to explain sorption in glassy polymers during the last few years. This review also includes the applications of glassy polymer. Despite having so many applications, current researchers still have difficulty in implementing coating challenges due to issues like as physical ageing, which is briefly discussed in the review.

Inert gas asphyxiation is a rarely observed form of suffocation in which the decedent breathes in an inert chemical, such as helium or nitrogen, in the absence of oxygen. The ultimate cause of death is not a result of the chemical itself, but rather from the oxygen starvation as the inert gas displaces vital oxygen. In this case report, a 66-year-old Caucasian female with a history of gastroparesis, degenerative disc disease, and chronic pain was found deceased with a plastic bag secured around her head. Plastic tubing terminated inside the bag and connected to a nearby canister of nitrogen gas. This case study discusses the challenges in determining inert gas asphyxiation as the cause of death in a postmortem setting and emphasizes the importance of understanding the decedent’s history and context of the environment in which they were found.

This paper consists of the design and implementation of a simple conditioning circuit to optimize the electronic nose performance, where a temperature modulation method was applied to the heating resistor to study the sensor’s response and confirm whether they are able to make the discrimination when exposed to different volatile organic compounds (VOC’s). This study was based on determining the efficiency of the gas sensors with the aim to perform an electronic nose, improving the sensitivity, selectivity and repeatability of the measuring system, selecting the type of modulation (e.g., pulse width modulation) for the analytes detection (i.e., Moscatel wine samples (2% of alcohol) and ethyl alcohol (70%)). The results demonstrated that by using temperature modulation technique to the heating resistors, it is possible to realize the discrimination of VOC’s in fast and easy way through a chemical sensors array. Therefore, a discrimination model based on principal component analysis (PCA) was implemented to each sensor, with data responses obtaining a variance of 94.5% and accuracy of 100%.

Parmigiano Reggiano cheese is one of the most appreciated and consumed food worldwide, especially in Italy, for its high content of nutrients and for its taste. However, these characteristics make this product subject to counterfeiting in different forms. In this study, a novel method based on an electronic nose has been developed in order to investigate the potentiality of this tool to distinguish rind percentage in grated Parmigiano Reggiano packages that should be lower than 18%. Different samples in terms of percentage, seasoning and rind working process were considered to tackle the problem at 360°. In parallel, GC-MS technique was used to give a name to the compounds that characterize Parmigiano and to relate them with sensors responses. Data analysis consisted of two stages: multivariate analysis (PLS) and classification made in a hierarchical way with PLS-DA ad ANNs. Results are promising in terms of correct classification of the samples. The classification rate is higher for ANNs than PLS-DA, reaching also 100% values.

Environmental assessment is a concept that has been designed to facilitate the present generation to meet their needs without compromising the ability of future generations to meet their own needs as well. Thus, this concept has drawn significant attention from various scholars, researchers and industrial practitioners around the world over the past three decades. Life Cycle Environmental Assessment (LCEA) is a widely metric used to assess the potential ecological impacts, which can be caused by electricity generating supply systems or by other systems than power production plants. However, the current LCEA model is biased and ineffective. Because, its omits factors that are increasingly contributing to the ecological degradation. This study has identified the omitted factors through a critical analysis of a set of previous journal articles conducted in the energy sector. In light of this, this study has developed a novel LCEA framework addressing those blind spots. The framework developed in this study is holistic in nature including all the life cycle stages of a power supply system such as Extraction of the Raw Material (ERM), Transport of Raw Material (TRM), Conversion of Raw into Electricity (CRE), and Transmission and Distribution of Electricity (TDE) to the end users. The novel developed LCEA model has been tested and applied to nine power generation plants such as coal, gas, nuclear, biomass, geothermal, hydro, solar thermal, wind onshore and wind offshore. The results have demonstrated that of conventional technologies including coal, gas, and nuclear, coal energy generating source has got the highest life cycle greenhouse gas Grid Emission Factor (GEF) of 2866 kg CO2e/MWh, followed by gas with 728 kg CO2e/MWh, and nuclear has got the least GEF of 35 kg CO2e/MWh. Whereas of renewable energy sources biomass has got the highest GEF of 1508 kg CO2e/MWh, followed by solar thermal with 46.6 kg CO2e/MWh, hydro 39 kg CO2e/MWh, wind offshore 25.25 kg CO2e/MWh, wind onshore 10.1 kg CO2e/MWh, and geothermal closes the ranking with 6.23 kg CO2e/MWh.

The aim of this paper is the presentation of an analytical model of insulator flashover and its application for air at atmospheric pressure and pressurized SF6. After a review of the main existing models in air and compressed gases, we develop a relationship of flashover voltage on the basis of an electrical equivalent circuit and the thermal properties of the discharge. The model includes the discharge resistance, the insulator impedance, and the gas interface impedance. The application of this model to a cylindrical resin-epoxy insulators in air medium and SF6 gas with different pressures gives results close to the experimental measurements.

The basic equation for estimating the aerodynamic power captured by an Anderson Vertical Axis Wind Turbine (AVAWT) is a solution of the Navier-Stokes(N-S) equations for a baroclinic, inviscid flow. In a nutshell, the pressure difference across the AVAWT is derived from Bernoulli’s equation; an upshot of the integration of the N-S momentum equation for a baroclinic inviscid flow, Euler’s momentum equation. The resulting expression for the pressure difference across the AVAWT rotor is plotted as a function of freestream speed. Experimentally determined airstream speeds at the AVAWT inlet and outlet, coupled with corresponding freestream speeds are used in estimating the aerodynamic power captured. The aerodynamic power is subsequently used in calculating the aerodynamic power coefficient of the AVAWT. The actual power coefficient is calculated from the power generated by the AVAWT at various free stream speeds and plotted as a function of the latter. Experimental results show that, at all free stream speeds and tip speed ratios, the aerodynamic power coefficient is higher than the actual power coefficient of the AVAWT. Consequently, the power generated by the AVAWT prototype is lower than the aerodynamic power captured, given the same inflow wind condition.

In this paper a novel type of a highly sensitive gas sensor device based on the surface photovoltage effect is described. The developed surface photovoltage gas sensor is based on a reverse Kelvin probe approach. As the active gas sensing electrode the porous ZnO nanostructured thin films are used deposited by the direct current (DC) reactive magnetron sputtering method exhibiting the nanocoral surface morphology combined with an evident surface nonstoichiometry related to the unintentional surface carbon and water vapor contaminations. Among others, the demonstrated SPV gas sensor device exhibits a high sensitivity of 1 ppm to NO₂ with a signal to noise ratio of about 50 and a fast response time of several seconds under the room temperature conditions.

The present study explores the effect of using two porous deflectors on the performance of the Savonius wind turbine compared to only one porous deflector. The numerical simulation is performed to solve the unsteady Navier-Stokes equations using the SST k-

Some wind farms have implemented automated camera\textendash based monitoring systems e.g. IdentiFlight to mitigate the impact of wind turbines on protected raptors. These systems have effectuated the collection of large amounts of data that can be used to describe flight behavior in a novel way. This data uniquely provides both flight trajectories and images of individual birds throughout their flight trajectories. The aim of this study was to evaluate how this unique data could be used to create a robust quantitative behavioral analysis, that could be used to identify risk prone flight behavior and avoidance behavior thereby in the future assess collision risk. This was attained through a case study at a wind farm on the Swedish island Gotland, where golden eagles (Aquila chrysaetos), white-tailed eagles (Haliaeetus albicilla), and red kites (Milvus milvus), were chosen as the selected bird species. The results demonstrate that flight trajectories and bird images can be used to identify high risk flight behavior and thereby also used to evaluate collision risk and avoidance behavior. This study presents a promising framework for future research, demonstrating how data from camera\textendash based monitoring systems can be utilized to quantitatively describe risk prone behavior and thereby assess collision risk and avoidance behavior.

When attempting to quantify future harms caused by carbon emissions and to set appropriate energy policies, it has been argued that the most important metric is the number of human deaths caused by climate change. Several studies have attempted to overcome the uncertainties associated with such forecasting. In this article, approaches to estimating future human deaths tolls from climate change are compared and synthesized, and implications for energy policy are considered. Several studies are consistent with the “1000-ton rule,” according to which a future person is killed every time 1000 tons of fossil carbon are burned (order-of-magnitude estimate). If warming reaches or exceeds 2°C this century, mainly richer humans will be responsible for killing roughly 1 billion mainly poorer humans through anthropogenic global warming. Such mass manslaughter is clearly unacceptable. On this basis, relatively aggressive energy policies are summarized that would enable immediate and substantive decreases to carbon emissions. The limitations to such calculations are outlined and future work is recommended to accelerate the decarbonization of the global economy while minimizing the number of sacrificed human lives.

The vegan diet excludes animal-derived products consumption. The objective of the present study is to analyze dietary lipid intake, nine plasmatic fatty acids concentrations (from C14:0 [lauric acid] to C20:4 [arachidonic acid]), and conventional clinical lipid profile among vegan individuals with omnivore controls. A case-control and cross-sectional study was performed between 2016 and 2017. Vegans were paired in a 1:1 ratio with omnivores from Merida, Mexico. A 150-item Semi-Quantitative Food Frequency Questionnaire was conducted to evaluate eating patterns. Serum fatty acids were determined from total blood with a gas chromatography assay. Lower cholesterol, stearic, arachidonic and trans fatty acids intake, but higher consumption of lauric acid were observed in the vegan group (p= <0.001, 0.014, <0.001, 0.005, respectively). Decreased plasma concentrations of stearic, arachidonic and linoleic acids were found (p= 0.017, <0.001 and 0.026, respectively). Following a vegan diet for more than three years generate modifications in serum concentrations of saturated and polyunsaturated ω-6 fatty acids, which could lower inflammatory markers’ biosynthesis. Potential benefits regarding cardiovascular risk may be assumed in favor of vegan individuals.

Biomarkers have the potential to aid in the study of Alzheimer’s disease (AD); unfortunately, AD biomarker values often have a high degree of overlap between healthy and AD individuals. This study investigates the potential utility of a series of novel AD biomarkers, the sixty second ¹²⁹Xe retention time, and the xenon washout parameter, based on the washout of hyperpolarized ¹²⁹Xe from the brain of AD participants following inhalation. The xenon washout parameter is influenced by cerebral perfusion, T1 relaxation of xenon, and the xenon partition coefficient, all factors influenced by AD. Participants with Alzheimer’s disease (n=4) and healthy volunteers (n=4) were imaged using hyperpolarized ¹²⁹Xe magnetic resonance imaging (MRI) and magnetic resonance spectroscopy (MRS) to determine the amount of retain xenon in the brain. At 60 sec post breath hold, AD patients retained significantly higher amounts of ¹²⁹Xe compared to healthy controls. Data was fit to a pharmacokinetic model and the xenon washout parameter was extracted. Xenon washout in white and grey matter occurs at a slower rate in Alzheimer’s participants (¹²⁹Xe half-life time of 42s and 43s, respectively) relative to controls (20s and 16s, respectively). Following larger scale clinical trials for validation, the xenon washout parameter has the potential to become a useful biomarker for the support of an AD diagnosis.

A growing number of companies in the brewery industry have made commitments to measure and reduce their greenhouse gas (GHG) emissions. However, many brewers, particularly craft brewers with relatively low rates of production, have struggled to meet these commitments. The purpose of this research was to investigate the challenges and benefits of measuring and reducing GHG emissions in the craft brewery industry. The research was conducted in Ontario, Canada, which has seen strong recent growth in the craft brewery industry. A case study and semi-structured interviews among Ontario Craft Brewers were conducted. The case study found that indirect (scope 3 emissions under the WBCSD & WRI GHG Protocol) GHG sources accounted for 46.4% of total GHGs, with major sources from barley agriculture, malted barley transportation, and bottle production. Direct emissions (scope 1) accounted for only 14.9% of GHGs, while scope 2 emissions, comprised mainly of energy consumption, accounted for 38.7% of GHGs. The case study and interviews found that the main challenges in calculating brewery GHGs are secondary data availability, technical knowledge, and finances. The study also found that the main benefits for Ontario breweries to measure their GHGs include sustainability marketing and preserving the environment. The interviews also found a poor understanding of carbon regulation among Ontario Craft Brewers, which is interesting considering that Ontario implemented a provincial cap and trade program in 2017.

Low pasture biomass production and fodder scarcity are among the major challenges affecting productivity of dairy cattle farms in Sri Lanka. As a potential solution to this, two Napier hybrid cultivars CO-5 and Sampoorna were recently introduced and a field experiment was conducted to evaluate their growth, dry matter production and nutritional composition during May to September 2020. Plant measurements and samples were collected at five harvest intervals (4, 6, 8, 10 and 12 weeks after planting), with the plant samples subjected to biomass and nutritional assessments. The number of tillers and leaf length differed (P=0.01) between the two cultivars at 4 weeks harvesting interval (HI) whilst number of leaves differed at 12 HI respectively. Dry matter yield increased (P=0.16) almost linearly whilst crude protein declined exponentially with CO-5 greater than Sampoorna (P=0.057; 9.3% vs 8.7%), with increasing harvesting intervals respectively. In-vitro Organic Matter Digestibility and In-vitro Metabolizable Energy contents were similar across weeks 4, 6 and 8 but then decreased. This study demonstrates that higher dry matter yields (12.54 t/ha) can be obtained by harvesting both cultivars at 12 HI, but from a nutritional perspective harvesting at 6 HI during Yala season of the year would be optimum for farmers.

The Virtual Blade Model (VBM) is the implementation of the Blade element model (BEM). This was done by coupling the Blade Element Momentum theory equations to simulate rotor operation with the Reynolds Averaged Navier-Stokes (RANS) equation to simulate rotor wake and the turbulent flow field around it. Exclusion of actual geometry of blades causes lower computational cost (about 10 to 100 times). Also, due to simplifications in the meshing procedure, VBM is easier to set up than the models that consider the actual geometry of blades. One of the main unaddressed limitations of the VBM code was the constraint of modeling up to ten rotor zones within one computational domain. This paper provides a detailed and well-documented general methodology to develop a virtual blade model for simulation of ten-plus turbines within one computational domain to remove the limitation of this widely used and robust code. It is strongly believed that the technical contribution of this paper, combined with the current sky-rocketing advancement of available computational resources and hardware, would open the gates to simulate various engineering problems in the field of aerospace, clean energy, and many more.

Vanadium titano-magnetite is a significant resource in China, and in this study, we characterize its isothermal reduction mechanisms in the mixture of H₂, CO, and N₂ where the variables considered here include reduction time, reduction temperature, gas composition, and pellet size. The kinetics of the reduction process are mainly studied, which follows a shrinking core model. The results indicate that the reduction degree of oxidized VTM pellets increases with the increase of reduction time, reduction temperature but decreases with the increase of pellet size. Moreover, we found that an increase of H₂/(H₂+CO) ratio induces an increase of the reduction degree. Then the transformation of main Ti-bearing mineral phases is discussed, and the most probable reaction mechanism is revealed. In the whole reduction process, the kinetic results confirm the existence of an early stage and a latter stage, which are controlled by interface chemical reaction and diffusion, respectively. Furthermore, the results show that the diffusion-control step can be observably shortened with the decrease of pellet size because a thinner product layer is formed during the reduction process. Our study thus provides a valuable technical basis on the VTM industrial application.

Due to failure of the continuum hypothesis for higher Knudsen numbers, rarefied gases and microflows of gases are particularly difficult to model. Macroscopic transport equations compete with particle methods, such as DSMC to find accurate solutions in the rarefied gas regime. Due to growing interest in micro flow applications, such as micro fuel cells, it is important to model and understand evaporation in this flow regime. Here, evaporation boundary conditions for the R13 equations, which are macroscopic transport equations with applicability in the rarefied gas regime, are derived. The new equations utilize Onsager relations, linear relations between thermodynamic fluxes and forces, with constant coefficients, that need to be determined. For this, the boundary conditions are fitted to DSMC data and compared to other R13 boundary conditions from kinetic theory and Navier-Stokes-Fourier (NSF) solutions for two one-dimensional steady-state problems. Overall, the suggested fittings of the new phenomenological boundary conditions show better agreement to DSMC than the alternative kinetic theory evaporation boundary conditions for R13. Furthermore, the new evaporation boundary conditions for R13 are implemented in a code for the numerical solution of complex, two-dimensional geometries and compared to NSF solutions. Different flow patterns between R13 and NSF for higher Knudsen numbers are observed.

Here we investigate how the local properties of particles in a thermal bath may influence the thermodynamics of the bath, and consequently alter the statistical mechanics of subsystems that comprise the bath. We are guided by the theory of small-system thermodynamics, which is based on two primary postulates: that small systems can be treated self-consistently by coupling them to an ensemble of similarly small systems, and that a large ensemble of small systems forms its own thermodynamic bath. We adapt this “nanothermodynamics” to investigate how a large system may subdivide into an ensemble of smaller subsystems, causing internal heterogeneity across multiple size scales. For the semi-classical ideal gas, maximum entropy favors subdividing a large system of “atoms” into an ensemble of “regions” of variable size. The mechanism of region formation could come from quantum exchange symmetry that makes atoms in each region indistinguishable, while decoherence between regions allows atoms in separate regions to be distinguishable by their distinct locations. Combining regions reduces the total entropy, as expected when distinguishable particles become indistinguishable, and as required by a theorem in quantum mechanics for sub-additive entropy. Combining large volumes of small regions gives the usual entropy of mixing for a semi-classical ideal gas, resolving Gibbs paradox without invoking quantum symmetry for atoms that may be meters apart. Other models presented here are based on Ising-like spins, which are solved analytically in one dimension. Focusing on the bonds between the Ising-like spins we find similarity in the equilibrium properties of a two-state model in the nanocanonical ensemble and a three-state model in the canonical ensemble. Thus, emergent phenomena may alter the thermal behavior of microscopic models, and the correct ensemble is necessary for fully-accurate predictions. Another result using Ising-like spins involves simulations that include a nonlinear correction to Boltzmann’s factor, which mimics the statistics of indistinguishable states by imitating the dynamics of spin exchange on intermediate lengths. These simulations exhibit 1/f-like noise at low frequencies (f), and white noise at higher f, similar to equilibrium thermal fluctuations found in many materials.

The important sampling parameters of a headspace solid phase microextraction-gas chromatography-mass spectrometry (HS-SPME-GC-MS) procedure, extraction temperature, extraction time and sample volume were optimized to quantify 23 important impact odorants in reduced alcohol red and white wines. A three-factor design of Box-Behnken experiments was used to determine optimized sampling conditions for each analyte, and a global optimized condition at every ethanol concentration of interest determined using a desirability function that accounts for a low signal response for compounds. Shiraz and Chardonnay wines were dealcoholized from 13.7 and 12.2% v/v ethanol respectively, to 8 and 5% v/v, using a commercially available membrane-based technology. A sample set of the reduced alcohol wines were also reconstituted to their natural ethanol level to evaluate the effect of ethanol content reduction on volatile composition. The three-factor Box-Behnken experiment ensured an accurate determination of the headspace concentration of each compound at each ethanol concentration, allowing comparisons between wines at varying ethanol levels to be made. Overall, the results showed that the main effect of extraction temperature was considered the most critical factor when studying the equilibrium of reduced alcohol wine impact odorants. The impact of ethanol reduction upon the concentration of volatile compounds clearly resulted in losses of impact odorants from the wines. The concentration of most analytes decreased with dealcoholization compared to that of the natural samples. Significant differences were also found between the reconstituted volatile composition and 5% v/v reduced alcohol wines, revealing that the dealcoholization effect is the result of a combination between the type of dealcoholization treatment and reduction in wine ethanol content.

The present study was carried out at the north-eastern part of Bangladesh to investigate organochlorine pesticide (OCP) residues and microbiological quality of dried barb (Puntius sophore). Samples were collected from both producers and retailers from December 2016 to April 2017. A control sample was also prepared with the same raw fish used by the producers in the laboratory to compare the result. Gas Chromatography with Electron Capture Detector (GC-ECD) was used to detect and quantify OCP residues. Around 22 % (6) samples out of 27 were found contaminated with OCP residues. Among these six adulterated samples, four were from retailers and two from producers. Only Aldrin was detected in four samples and rest two samples were detected with both Aldrin + Dieldrin and Aldrin + Endrin. Aldrin was found between 0.332 to 0.967 ppm, Dieldrin 0.762 ppm, and Endrin 0.828 ppm. All these values were much higher than the Maximum Residual Limit (MRL) 0.1 ppm. Aerobic Plate Count (APC) of producer samples were ranged between log5.3 ± 0.02 to log5.4 ± 0.03, log6.2 ± 0.02 to log6.4 ± 0.02 for retailer samples and log5.0 ± 0.03 to log5.2 ± 0.04 for control samples. While fungal count was ranged between log3.2 ± 0.04 to log3.5 ± 0.04, log3.4 ± 0.04 to log3.6 ± 0.03 and log2.2 ± 0.05 to log2.5 ± 0.03 for producer, retailer and control samples respectively. All the producer and retailer samples and one-third of the control samples were found contaminated with Escherichia coli. Whereas, Salmonella sp. was detected as 13.3% in producer samples, 20% in retailer samples except for the control. In case of Vibrio sp., maximum count was found for retailer samples (13.3%), whereas, producer and control samples showed no detection. The finding of the present study revealed the presence of pesticides and poor microbiological quality of dried barb are alarming for the consumers of Bangladesh and which may cause chronic disease and potential long-term risk for human health.

Nowadays, the imidazolium-based ionic liquids containing acetate counter-ions are attracting much attention as both highly selective absorbents of the acidic gases and CO₂ carriers in the supported ionic liquid membranes. In this regard, the investigation of the gas transport properties of such membranes may be appropriate for better understanding of various factors affecting the separation performance and the selection of the optimal operating conditions. In this work, we have tested CH₄, CO₂ and H₂S permeability across the SILM impregnated by 1-butyl-3-methylimidazolium acetate (bmim[ace]) with the following determination of the ideal selectivity in order to compare the facilitated transport membrane performance with the SILM that dissolves acidic gases physically, namely, containing 1-butyl-3-methylimidazolium tetrafluoroborate (bmim[BF₄]). Both SILMs have showed modest individual gases permeability and ideal selectivity of CO₂/CH₄ and H₂S/CH₄ separation that achieves values up to 15 and 32, respectively. The effect of the feed gas mixture composition on the permeability of acidic gases and permeselectivity of the gas pair was investigated. It turned out that the permeation behavior for the bmim[ace]-based SILM toward the binary CO₂/CH₄, H₂S/CH₄ and ternary CO₂/H₂S/CH₄ mixtures was featured with high acidic gases selectivity due to the relatively low methane penetration through the liquid phase saturated by acidic gases.

This research paper presents a new application of electroactive polyimide doped with gold nanoparticles (PI/AuNPs) as a chemiresistor sensor for detecting hydrogen sulfide gas. The synthesis of PI/AuNPs was done in a simple 3-step process of polymerization using the as prepared amine-capped aniline trimer (ACAT), followed by imidization, and doping. Spectral analyses via FTIR, LC-MS and ¹H-NMR confirmed the formation of amine-capped aniline trimer with a MW of 288 g mol^-1. Comparison of ACAT, BSAA, and PI FTIR spectra showed successful polymerization of the last, while XRD validated the incorporation of metal nanoparticles onto the polymer matrix showing characteristic diffraction peaks corresponding to gold. Furthermore, TEM, and FE-SEM revealed the presence of well-dispersed Au nanoparticles with an average diameter of about 60nm. The electroactive PI/AuNPs-based sensor showed a sensitivity of 0.29% ppm^-1 H₂S at a linear concentration range of 50 to 300 ppm H₂S (r = 0.9777). The theoretical limit of detection was found at 0.142 ppm or 142 ppb H₂S gas. The sensor provided a stable response reading at an average response time of 43±5 seconds, which was easily recovered after an average time of 99±5 seconds. The sensor response was highly repeatable and reversible with RSD values of 8.88%, and 8.60%, respectively. Compared with the performance of the conventional conducting polyaniline also doped with gold nanoparticles (PANI/AuNPs), the fabricated electroactive PI/AuNPs exhibited improved sensing performance making it a potential candidate in monitoring H₂S in the environment and for work-related safety.

In reservoir engineering, one of the main sources of information for the characterization of reservoir and well parameters is well testing. Among the unconventional well testing methodologies, Harmonic Well Testing (HPT) is appealing from an economic standpoint because it could provide well performance and reservoir behavior monitoring without having to interrupt field production. Recorded pressure analysis is performed in the frequency domain by adopting a derivative approach similar to conventional well testing. To this end, pressure and rate data must be decomposed into harmonic components. Test interpretability can be significantly improved if pressure data are detrended prior to interpretation, filtering out non periodic events such as discontinuous production from neighboring wells and flow regime variations which did not respect the designed test periodicity. Therefore, detrending offers the possibility of overcoming the limitation of HPT applicability due to the difficulty of imposing a regularly pulsing rate for the whole test duration (typically lasting several days). This makes HPT attractive for well performance monitoring, especially in gas storage fields. In this paper, the application of different detrending methodologies to synthetic HPT pressure data generated in different reservoir and operational scenarios is presented and discussed. Moreover, a real case application is also presented.

In April 2019, a team of Keio University and Bucknell University students was assembled to participate in Ericsson Innovation Awards with a novel concept for generating renewable energy. This conceptual system consists of a vertical axis wind turbine, a crossflow marine hydrokinetic turbine, a floating platform integrated with a quadcopter system, and three to four temporary mooring lines with ship-type anchors. The proposed designed aims to offer solutions to two current problems of floating offshore wind energy: high construction cost of floating platforms and difficulties in maintenance of mooring lines. The combination of two vertical-axis turbines into a single floating platform would enable the system, namely ESwift, to extract energy from both wind and current resources. Additionally, due to the utilization of vertical axis turbines, the center of gravity of the proposed concept is significantly lower with respect to water level, compared to that of existing floating horizontal axis wind turbines, which would potentially reduce the floater's size and construction cost. Lastly, the integrated quadcopter mechanism would assist the floater in terms of stability and mobility, and enables an array of ESwifts to automatically rearrange for maximal energy generation. The authors hope that readers would find the idea described in this open access letter worth pursuing and would further develop and commercialize the ESwift concept.

This study investigated the evolution of density, gas permeability and thermal conductivity of sugar maple wood during the thermo-hygro-mechanical densification process. The results suggested that the oven-dry average density of densified samples was significantly higher than that of the control samples. However, the oven-dry density did not show a linear increase with the decrease of wood samples thickness. The radial intrinsic gas permeability of the control samples was 5 to 40 times higher than that of densified samples, which indicated that the void volume of wood was reduced notably after the densification process. The thermal conductivity increased by 0.5 - 1.5% per percent increase of moisture content for densified samples. The thermal conductivity of densified wood was lower than that of the control samples. The densification time had significant effects on the oven-dry density and gas permeability. Both the densification time and the moisture content had significant effects on thermal conductivity, but their interaction effect was not significant.

The overall cost of a hydropower plant is mainly due to the expenses for civil works, mechanical equipment (turbine and control units) and electrical components. The goal of a new draft tube design is to obtain a geometry that reduces investment costs, especially the excavation ones, but the primary driver is to increase the overall machine efficiency allowing for reduced payback time. In the present study, an optimization study of the elbow-draft tube assembly of a Kaplan turbine was conducted. A CFD model for the complete turbine has been developed and validated; next, an optimization of the draft tube alone was performed using a Design of Experiments technique; finally, several optimum solutions for the draft tube were obtained using a Response Surface technique aiming at maximizing pressure recovery and minimizing flow losses. A selection of optimized geometries was subsequently post-checked using the validated model of the entire turbine and a detailed flow analysis on the obtained results could make it possible to provide insight into the improved designs. It was observed that efficiency could be improved by 1% (in relative terms), and the mechanical power increased by 1,8% (in relative terms) with respect to the baseline turbine.

Volatile organic compounds (VOCs) are among the most abundant air pollutants. Their high concentrations can adversely affect the human body and therefore, early detection of VOCs is of outmost importance. Among the different VOCs, in this review paper, we have focused our attention on the monitoring of acetaldehyde by chemiresistive gas sensors using nanostructured semiconducting metal oxides. These sensors not only can provide a high sensing signal for detection of acetaldehyde, but also high thermal and mechanical stability and low price. This review paper is divided into three major sections. First, we will introduce acetaldehyde as the target gas and the importance of its detection. Then, the fundamentals of chemiresistive gas sensors will be briefly presented and, in the last section, a survey of literature on acetaldehyde gas sensors will be discussed. Acetaldehyde sensors working mechanism, their structures and configurations are reviewed. Finally, the future development outlook and potential applications are discussed, giving a complete panoramic view for researcher working and interested in acetaldehyde detection for different purposes in many fundamentals and applicative fields.

The conversion of C1 gas feedstock, such as carbon monoxide (CO), into useful platform chemicals has attracted considerable interest in industrial biotechnology. One conversion method is electrode-based electron transfer to microorganisms using bioelectrochemical systems (BESs). In this BES system, acetate is the predominant component of various volatile fatty acids (VFAs). To appropriately separate and concentrate the produced acetate, a BES type electrodialysis cell with an anion exchange membrane was constructed and evaluated under various operational conditions, such as the applied external current. The higher acetate flux of 23.9 mmol/m2∙hr was observed under -15 mA current in an electrodialysis-based bioelectrochemical system. In addition, the initial acetate concentration affects the separation efficiency and transportation rate. The maximum flux appeared at 48.6 mmol/m2∙hr when the acetate concentration was 100mM, whereas the effect of the initial pH of the anolyte was negligible. The acetate flux was 14.9 mmol/m2∙hr when actual fermentation broth from BES based CO fermentation, was used as a catholyte. A comparison of the synthetic medium with the actual fermentation medium suggests that unknown substances and metabolites in the actual medium interfere with electrodialysis in the BES. These results provide information on the separation and optimal concentration for VFAs produced by C1 gas fermentation through electrodialysis, and a combination of a BES and electrodialysis.

In this paper, the active front-end (AFE) converter topology for the total harmonic distortion (THD) reduction in a wind energy system (WES) is used. A higher THD results in serious pulsations in the wind turbine (WT) output power and in several power losses at the WES. The AFE converter topology improves capability, efficiency and reliability in the energy conversion devices; by modifying a conventional back-to-back converter, from using a single voltage source converter (VSC) to use pVSC connected in parallel the AFE converter is generated. The THD reduction is done by applying a different phase shift angle at the carrier of digital sinusoidal pulse width modulation (DSPWM) switching signals of each VSC. To verify the functionality of the proposed methodology, the WES simulation in Matlab-Simulink® is analyzed, and the experimental laboratory tests using the concept of rapid control prototyping and the real-time simulator Opal-RT® Technologies is achieved. The obtained results show a type-4 WT with total output power of 6MVA, generating a THD reduction up to 5.5 times at the WES.

Tidal stream energy, due to its high level of consistency and predictability, is one of the feasible and promising type of renewable energy for future development and investment. Applicability of Blade Element Momentum (BEM) method for modeling the interaction of turbines in tidal arrays has been proven in many studies. Apart from its well-known capabilities, yet there is scarcity of research using BEM for the modeling of tidal stream energy farms considering full scale rotors. In this paper, a real geographical site for developing a tidal farm in the southern coasts of Iran is selected. Then, a numerical methodology is validated and calibrated for the selected farm by analyzing array of turbines. A linear equation is proposed to calculate tidal power of marine hydrokinetic turbines. This methodology narrows down the wide range of turbine array configurations, reduces the cost of optimization and focuses on estimating best turbine arrangements in a limited number of positions.

A realistic implementation of an all-fiber CO₂ sensor, using 74 cm of hollow core PCF fiber as the cavity for light/gas interaction, has been implemented. It is based on CO₂ absorbance in the 2 μm region. The working range is from 2% to 100% CO₂ concentration at 1 atm total pressure. The response time obtained was 10 min. The use of an FBG tuned fiber ring laser, specifically designed for this application, is discussed and preliminary results with this laser are also presented.

The interest on the use of renewable energy resources is increasing, especially towards wind and hydro powers, which should be efficiently converted into electric energy via suitable technology tools. To this aim, data--driven control techniques represent viable strategies that can be employed for this purpose, due to the features of these nonlinear dynamic processes working over a wide range of operating conditions, driven by stochastic inputs, excitations and disturbances. Some of the considered methods, such as fuzzy and adaptive self--tuning controllers, were already verified on wind turbine systems, and similar advantages may thus derive from their appropriate implementation and application to hydroelectric plants. These issues represent the key features of the work, which provides some guidelines on the design and the application of these control strategies to these energy conversion systems. The working conditions of these systems will be also taken into account in order to highlight the reliability and robustness characteristics of the developed control strategies, especially interesting for remote and relatively inaccessible location of many installations.

Large amounts of gas hydrate are present in marine sediments offshore Taitao Peninsula, near the Chile Triple Junction. Here, marine sediments on the forearc contain carbon that is converted to methane in a zone of very high heat flow and intense rock deformation above the downgoing oceanic spreading ridge separating the Nazca and Antarctic plates. This regime enables vigorous fluid migration. Here we present an analysis of the spatial distribution, concentration, estimate of gas phases (gas hydrate and free gas) and geothermal gradients in the accretionary prism and forearc sediments offshore Taitao (45.5° - 47° S). Velocity analysis of Seismic Profile RC2901-751 indicates gas hydrate concentration values <10% of the total rock volume, and extremely high geothermal gradients (<190 °Ckm^-1). Gas hydrates are located in shallow sediments (90-280 meters below the seafloor). The large amount of hydrate and free gas estimated (7.21x10¹¹ m³ and 4.1x10¹⁰ m³, respectively), the high seismicity, the mechanically unstable nature of the sediments, and the anomalous geothermal conditions, set the stage for potential massive releases of methane to the ocean mainly through hydrate dissociation and/or migration directly to the seabed through faults. We conclude that the Chile Triple Junction is an important methane seepage area and should be the focus of novel geological and ecological research.

Background: Qazvin province has suffered a lot of natural disasters (earthquakes) for a long time. so, the establishment of the first industrial city in Iran, has always been a source of concern. One of these problems is the possibility of chlorine gas leaking from the chlorination system of drinking water and treatment plant the existing ones are on the health of the inhabitants of this region.Material and method: This analytical study was carried out in Novorossiysk district of Alborz in December 2012. Initially, chlorine gas leakage scenarios from these facilities were simulated by ALOHA and WISER software, and then using the Emergency Level System, according to the CCPS Consultative Center's Chemical Process Safety Advice, the Emergency Response Program was presented. Results: ALOHA software, in comparison with WISER software, has more precision to identify and address the consequences of chlorine gas leakage hazards and according to the simulation of this software in the event of a leak from the well and water resources unit at 8240 m from the area and at night 7520 meters will be affected. Due to the speed of delivering results through the WISER software, this software can be used at times when the operating speed is considered (incident time).Conclusion: According to the CCPS model, the emergency conditions were classified at levels 3 and 4, therefore, the relevant crisis management agencies (Qazvin Crisis Management Committee, Alborz City Health Center, Red Crescent and Firefighting Authority) should provide training maneuvers At Alborz city level, and informing people of cities and industrial companies, many efforts have been made to reduce human and environmental damage in case of possible leakage.

Gas-liquid reactors pose transfer difficulties due to diffusion effects. It is necessary to master the aeration and hydrodynamics of the medium to conduct the reaction well and get a good performance. For this purpose, a study in a submerged membrane bioreactor with a useful volume of 30L, consisting of a microfiltration membrane with an average pore size of 0.14 mm having an effective surface area of 0.2 m2 and a PVC cylindrical air diffuser of radius 4 cm has been studied. The saline tracing method associated with a conductimetric follow-up made it possible to determine the residence times and the mixing time in the reactor at 4 different points both in recirculation and in the absence of recirculation. Gas retention was measured by the manometric method. The experiments were carried out at different temperatures of 25 ° C, at 45 ° C, with a variable air flow rate of 0.5 to 16 mL / s and different solutions (osmosis water, ammonium formate solution, solution ammonium formate + salt, synthetic rubber effluent). The results show that the mixing time varies from one point to another and the recirculation of the mixture reduces the mixing time. One of the positions is limiting, the transfer is done most by diffusion with a mixing time of 115 min without circulation and 65 min with circulation. Gas retention increases with aeration rate and temperature. On the other hand, the more the medium becomes rich in organic substances, the more the gaseous retention decreases. The homogeneous fine-bubble regime is obtained for an air flow rate of between 3 and 10 mL / s of aeration. Beyond this flow rate, the regime becomes heterogeneous without a transition phase for ammonium formate and formate ammonium + salt solutions.

Biogas contains more than 40% CO2 that can be removed to produce high quality CH4. Recently, CH4 production from CO2 methanation has been reported in several studies. In this study, CO2 methanation of biogas was performed over a 20 wt% Ni-Mg-Al catalyst, and the effects of CO2 conversion rate and CH4 selectivity were investigated as a function of CH4, O2, H2O, and N2 compositions of the biogas. At a gas hourly space velocity (GHSV) of 30,000/h, the CO2 conversion rate was ~79.3% with a CH4 selectivity of 95%. In addition, the effects of the reaction temperature (200–450 °C), GHSV (21,000–50,000/h), and H2/CO2 molar ratio (3–5) on the CO2 conversion rate and CH4 selectivity over the 20 wt% Ni-Mg-Al catalyst were evaluated. The characteristics of the catalyst were analyzed using Brunauer-Emmett-Teller (BET) surface area analysis, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). The catalyst was stable for approximately 200 h at a GHSV of 30,000/h and a reaction temperature of 350 °C. CO2 conversion and CH4 selectivity were maintained at 75% and 93%, respectively, and the catalyst was therefore concluded to exhibit stable activity.

In the present work a novel, portable and innovative eNose composed of a surface acoustic wave (SAW) sensor array based ZIF-8, and ZIF-67 nanocrystals (pure and combined with gold nanoparticles) as sensitive layers has been tested as a non-invasive system to detect and differentiate disease markers, such as acetone, ethanol and ammonia, related with early diagnosis of diabetes mellitus through exhaled breath. The sensors have been prepared by spin coating, achieving continuous and homogenous sensitive layers. Low concentrations (5 ppm, 10 ppm and 25ppm) of the marker analytes were measured, obtaining high sensitivities, good reproducibility, short time response and fast signal recovery.

Inclusions in steels and alloys are known as factors that could lower deformation, mechanical, corrosion and other properties. Study of inclusions in nickel based alloys is important since these materials could suffer from corrosion degradation in harsh operational conditions, where inclusions could lead to a pitting initiation. For estimation of a harmful effect of different inclusions on corrosion resistance of Ni-based alloys, inclusion characteristics (such as composition, morphology, size, number and location) on film filter and dissolution of metal matrix around different inclusions on surfaces of metal samples after electrolytic extraction (EE) were investigated in two samples of industrial Ni-based alloys (alloy 718 and EP718). It was found that both Ni-based alloys have various inclusions: carbides (large size NbTi-C and small multicomponent carbides), nitrides TiNb-N and sulfides (TiNb-S in EP718 alloy). The higher harmful effect on corrosion resistance of metal was detected around sulfides and small carbides containing Mo, W, Cr. Dissolution effect was also observed around large carbides and nitrides, especially around inclusions having size more than 10 µm. Moreover, the dissolution of metal matrix around inclusions and clusters located on the grain boundaries is 2.1-2.7 times larger compared to that for those inclusions inside of grains of the given alloy samples.

In this study, we test the performance of a compact gas chromatograph with photoionization detector (GC-PID) and optimize the configuration to detect ambient (sub-ppb) levels of benzene, toluene, ethylbenzene, and xylene isomers (BTEX). The GC-PID system was designed to serve as a relatively inexpensive (~$10k) and field-deployable air toxic screening tool alternative to conventional benchtop GCs. The instrument uses ambient air as a carrier gas, and consists of a Tenax-GR trap preconcentrator, a gas sample valve, two capillary columns, and a photoionization detector (PID) with a small footprint and low power requirement. The performance of the GC-PID has been evaluated in terms of system linearity and sensitivity in field conditions. The BTEX-GC system demonstrated the capacity to detect BTEX at levels as high as 500 ppb with a linear calibration range of 0-100 ppb. A detection limit lower than 1 ppb was found for all BTEX compounds with a sampling volume of 1 L. No significant drift in the instrument was observed. A time-varying calibration technique was established that requires minimal equipment for field operations and optimizes the sampling procedure for field measurements. With an analysis time of less than 15 minutes, the compact GC-PID is ideal for field deployment of background and polluted atmospheres for near-real time measurements of BTEX. The results highlight the application of the compact and portable GC-PID for community monitoring and screening of air toxics.

The recent growing attention to energy saving and environmental protection issues has brought to attention the possibility of exploiting syngas from gasification of biomass and coal for the firing of industrial plants included the so called Integrated Gasification Combined Cycle ones. In order to improve the knowledge about the employ of syngas in lean premixed turbulent flames, a large scale swirl stabilized gas-turbine burner has been operated with a simplified model of H₂ enriched syngas from coal gasification. The experimental campaign has been performed at atmospheric pressure with operating conditions derived from scaling the real gas turbines ones. The results are here reported and consist of OH-PLIF measurements carried out at decreasing air equivalence ratio conditions and are analysed together with the mean aerodynamic characterisation of the burner flowfield in isothermal condition. The OH concentration distributions have been analysed statistically in order to obtain information about the location of the most reactive zones and an algorithm has been applied to the data in order to identify the flame fronts. In addition, the flame front locations have been successively interpreted statistically in order to obtain information about their main features and about their dependence on the air to fuel ratio behaviour.

Pyrolysis has been applied in the human economy for many years, and it has become a significant alternative to the production of chemical compounds, including biofuels. The article focuses mostly on recent achievements in the technical and processing aspects of pyrolysis. This review provides an overview of the recent advanced pyrolysis technology used in gas, bio-oil, and biochar production. The key parameters to maximize the production of specific chemical compounds were discussed and considered during the construction of the reactors. The emphasis is put on optimizing the process parameters, technical requirements, and renewable energy use in the process and conception to improve the efficiency of product production. The application of pyrolysis gas, oil, and biochar as valuable chemical compounds are related to the intensifying effects of climate change, biofuel production, and waste management in accordance with the principles of sustainable development.

Culture systems for 3-dimensional tissues, such as multicellular spheroids, are indispensable for high-throughput screening of primary or patient-derived xenograft (PDX)-expanded cancer tissues. Oxygen supply to the center of such spheroids is particularly critical for maintaining cellular functions as well as avoiding the development of a necrotic core. In this study, we evaluated 2 methods to enhance oxygen supply: (1) using culture plate with gas-permeable polydimethylsiloxane (PDMS) membrane at its bottom and (2) embedding hydrogel beads in the spheroids. Culturing spheroids on PDMS increased cell growth and affected glucose/lactate metabolism and CYP3A4 mRNA expression and subsequent enzyme activity. The spheroids comprised 5000 Hep G2 cells and 5000 20 µm-diameter hydrogel beads did not develop a necrotic core for 9 days when cultured on a gas-permeable sheet. In contrast, central necrosis in spheroids lacking hydrogel beads was observed after day 3 of culture, even when using PDMS. These results indicate that the combination of gas-permeable culture equipment and embedded hydrogel beads improves culture 3D spheroids produced from primary or PDX-expanded tumor cells.

Biochar application to soil has been proposed as a means for reducing soil greenhouse gas emissions and mitigating climate change. The effects, however, of interactions between biochar, moisture and temperature on soil CO₂ and N₂O emissions, remain poorly understood. Furthermore, the applicability of lab-scale observations to field conditions in diverse agroecosystems remains uncertain. Here we investigate the impact of a mixed wood gasification biochar on CO₂ and N₂O emissions from loess-derived soils using: (1) controlled laboratory incubations at three moisture (27, 31 and 35%) and three temperature (10, 20 and 30°C) levels, and (2) a field study with four cropping systems (continuous corn, switchgrass, low diversity grass mix, and high diversity grass-forb mix). Biochar reduced N₂O emissions under specific temperatures and moistures in the laboratory and in the continuous corn cropping system in the field. However, the effect of biochar on N₂O emissions was only significant in the field, and no effect on cumulative CO₂ emissions was observed. Cropping system also had a significant effect in the field study, with soils in grass and grass-forb cropping systems emitting more CO₂ and less N₂O than corn cropping systems. Observed biochar effects were consistent with previous studies showing that biochar amendments can reduce soil N₂O emissions under specific, but not all, conditions. The disparity in N₂O emission responses at the lab and field scales suggests that laboratory incubation experiments are not reliable for predicting the impact of biochar at the field scale.

Considering the high potential of hydrogen (H₂) as a clean energy carrier, the implementation of high performance and cost-effective biohydrogen (bioH₂) purification techniques is of vital importance, particularly in fuel cell applications. In this context, membrane technology is a potentially energy-saving solution to obtain high-quality biohydrogen. The most promising poly(ionic liquid) (PIL) - ionic liquid (IL) composite membranes previously studied by our group for CO₂/N₂ separation, containing pyrrolidinium-based PILs with fluorinated or cyano-functionalized anions, were chosen as starting point to explore the potential of PIL–IL membranes for CO₂/H₂ separation. The CO₂ and H₂ permeation properties at the typical conditions of biohydrogen production (T =308 K and 100 kPa of feed pressure) were measured and discussed. PIL–IL composites prepared with [C(CN)₃]^– anion showed higher CO₂/H₂ selectivities and H₂ diffusivities compared to those containing [NTf₂]^– anion. All the membranes revealed CO₂/H₂ separation performances above the upper bound for this specific separation, highlighting the composite incorporating 60 wt% of [C₂mim][C(CN)₃] IL.

The aim of this review is to provide a survey of the recent advances and the main remaining challenges related to the ultrananocrystalline diamond (UNCD) nanowires and other nanostructures which exhibit excellent capability as the core components for many diverse novel sensing devices, due to the unique material properties and geometry advantages. The doping introduced in the gas phase during deposition promotes p-type or n-type conductivity. With the establishment of the UNCD nanofabrication techniques, more and more nanostructure based devices are being explored in measuring basic physical and chemical parameters via classic and quantum methods, as exemplified by gas sensors, ultraviolet photodetectors, piezoresistance effect based devices, biological applications, and nitrogen-vacancy color center based magnetic field quantum sensors. Highlighted finally are some of the remaining challenges and future outlook in this area.

Original and improved version of the Hardy Cross iterative method with related modifications are today widely used for calculation of fluid flow through conduits in loops-like distribution networks of pipes with known node fluid consumptions. Fluid in these networks is usually natural gas for distribution in the municipalities, water in waterworks or hot water in district heating system, air in the case of ventilation systems in buildings or mines, etc. Since, the resistances in these networks depend of flow, problem is not linear like in electrical circuits, and iterative procedure must be used. In both version of the Hardy Cross method, in original and in the improved one, initial results of calculation in iteration procedure is not flow, but rather the correction of flow. Unfortunately, these corrections should be added to or subtracted from a flow calculated in previous iteration according to complicate algebraic rules. After the here presented node-loop method, final results in each of the iterations is flow directly rather than flow correction. In that way complex algebraic scheme for sign of flow correction is avoided, while the final results still remain unchanged. Numbers of required iterations for the same results are comparable with the improved Hardy Cross method.

We hypothesized possibility that inline registered reticulorumen pH can be as biomarker of cows reproduction and health status. Aim of this study was to evaluate the relationship of reticulorumen pH with biomarkers from automatic milking system (AMS) and some blood parameters and determinate reticulorumen pH as biomarker of cows reproduction and health status. According to cows reproductive status the cows were classified as belonging to the following four groups: 15-30 d. postpartum; 1-34 d. after insemination; 35 d. after insemination (non-pregnant); 35 d. after insemination (pregnant). According reticulorumen pH assay experimental animals were divided into four classes: 1) pH<6.22 (5.3% of cows), 2) pH - 6.22-6.42 (42.1% of cows), 3) pH - 6.42-6.62 (21.1% of cows), 4) pH >6.62 (10.5% of cows). Rumination time, body weight, milk yield, milk fat – protein ratio, milk lactose, milk somatic cell count (SCC), milk electrical conductivity of all quarters of udder were registered with the help of Lely Astronaut® A3 milking robots. The pH, temperature of the contents of cow reticulorumens and cow activity were measured using specific smaX-tec boluses. Blood gas parameters were analyzed using a blood gas analyzer (EPOC, Canada). We found that pregnant cows has higher reticulorumen pH during insemination time, comparing with non-pregnant. Cows with lower reticulorumen pH has lowest milk fat – protein ratio, and lactose concentration, and highest SCC. Cows with lowest reticulorumen pH has lowest blood pH. With increase reticulorumen pH, increases blood potasium and hematocrit, decreases CO2, saturation and sodium.

Hydraulic fracturing is the most effective method of stimulation for hydrocarbon reservoirs. However the use of water-based fracturing fluids, can be a problem in water-sensitive formations due to the permeability damage hazard caused by clay minerals swelling. For this reason, the foamed fracturing fluids with addition of natural, fast hydrating guar gum were examined. The rheology and filtration coefficients of foamed fracturing fluids were examined and compared to the properties of conventional water-based fracturing fluid. Laboratory results provided the input for numerical simulation of the fractures geometry for water-based fracturing fluids and 50% N₂ foamed fluids. The results show, that the foamed fluids were able to create shorter and thinner fractures compared to the fractures induced by the non-foamed fluid. The simulation proved that the concentration of proppant in the fracture and its conductivity are similar or slightly higher when using the foamed fluid. Moreover such fluids are able to significantly reduce the amount of water necessary for fracturing treatments, limiting clay minerals swelling, and reducing the reservoir permeability damage. The foamed fluids, when injected to the reservoir, provide additional energy, that allow for more effective flowback, and maintain the proper fracture geometry and proppant placing. The results of laboratory work in combination with the 3D simulation showed, that the foamed fluids have suitable viscosity which allows opening the fracture, and transport the proppant into the fracture, providing successful fracturing operation.

Gas hydrate provinces are present in at least in two areas along Brazil’s continental margin: (1) the Rio Grande Cone in the southeast, and (2) the Amazon deep-sea fan in the equatorial region. The occurrence of gas hydrates in these depocentres was first detected geophysically and has recently been proven by seafloor sampling of gas vents, detected as water column acoustic anomalies rising from seafloor depressions (pockmarks) and/or mounds, many associated with seafloor faults. The gas vents include typical features of cold seep systems, including shallow sulphate reduction depths (<4 m), authigenic carbonate pavements and chemosynthetic ecosystems. In both areas, gas sampled in hydrate and in sediments is dominantly formed by biogenic methane. Calculation of the methane hydrate stability zone for water temperatures in the two areas shows that gas vents occur along its feather edge (water depths between 510-760 m in the Rio Grande Cone and 500-670 m in the Amazon deep-sea fan) but also in deeper waters within the stability zone. Gas venting along the feather edge of the stability zone could reflect gas hydrate dissociation and release to the oceans, as inferred on other continental margins, or upward fluid flow through the stability zone facilitated by tectonic structures recording the gravitational collapse of both depocentres. The potential quantity of venting gas on the Brazilian margin under different scenarios of natural or anthropogenic change require further investigation. The studied areas provide a natural laboratory where these critical processes can be analysed and quantified.

The development and application of marine current energy are attracting more and more attention around the world. Due to the hardness of its working environment, it is important and difficult to study the fault diagnosis of a marine current generation system. In this paper, an underwater image is chosen as the fault-diagnosing signal, after different sensors are compared. This paper proposes a diagnosis method based on the sparse autoencoder (SA) and softmax regression (SR). The SA is used to extract the features and SR is used to classify them. Images are used to monitor whether the blade is attached by benthos and to determine its corresponding degree of attachment. Compared with other methods, the experiment results show that the proposed method can diagnose the blade attachment with higher accuracy.

In the steeply inclined and extremely thick coal seams (SIETCS) mined using the horizontal sublevel top-coal caving (HSTCC) method, the uncertainty of gas emission is a safety threat to the mining operations. In order to reduce the occurrence of accidents, the determination of gas emission is crucial. In this paper, we first proposed a prediction model for workers at the floor coalbed to calculate gas emission on site. We then put forward a finite element numerical simulation for researchers to predict gas emission from the floor coalbed. At last, we measured gas emitted from the floor coalbed of SIETCS in Wudong Coal Mine in a specific mining period and used the data to verify the applicability and accuracy of these two gas-emission prediction methods. The results showed that the gas emission from Wudong Coal Mine was 1.08 m³/min calculated based on the prediction model and 1.07 m³/min obtained using the user-defined integration method. Both methods have their own advantages, disadvantages and applicable objects, and are important in predicting gas emission from SIETCS mined using HSTCC method.

Recent maritime legislations demand the transformation of the sector to greener and more energy efficient transportation. Liquified Natural Gas (LNG) seems a promising alternative fuel solution that could replace the conventional fuel sources. Various studies have been focused on the prediction of LNG price, however, no previous work has been made on the forecast of spot charter rate of LNG carrier ships. An important knowledge for the maritime industries and companies when it comes to decision-making. Therefore, this study is focused on the development of a machine learning pipeline to address the aforementioned problem by: (i) forming a dataset with variables relevant to LNG; (ii) identifying the variables that impact on the freight price of LNG carrier; (iii) developing and evaluating regression models for short and mid-term forecast. The results showed that the General Regression Neural Network presented a stable overall performance for 2, 4 and 6 months forecast.

The differential gear train and speed regulating motor constitute the variable ratio transmission for grid-connected wind turbine with differential speed regulation. The synchronous generator in the system can accessing the power grid without frequency converter. The transmission can realize the mode of variable speed constant frequency that the wind rotor speed is varying and the generator rotor speed is constant. The power control method is studied under the different wind speed which is lower or higher than rated wind speed with using the relational expression of utilization rate of wind energy Cp, pitch angle β and the tip speed ratio λ. The SIMULINK software is used to build the 1500 kW wind turbine model with differential speed regulation. Some different wind speed is made as input. The feasibility of power control method for grid-connected wind turbine with differential speed regulation is verified by the comparison between the simulation results and the theoretical value of the key parameters.

Fabric phase sorptive extraction, an innovative integration of solid phase extraction and solid phase microextraction principles, has been combined with gas chromatography-mass spectrometry for the rapid extraction and determination of nineteen organochlorine pesticides in various fruit juices and water samples. FPSE consolidates the advanced features of sol-gel derived extraction sorbents with the rich surface chemistry of cellulose fabric substrate, which could directly extract target analytes from complex sample matrices and substantially simplifies the sample preparation operation. Important FPSE parameters including sorbent chemistry, extraction time, stirring speed, type and volume of back-extraction solvent and back-extraction time have been optimized. Calibration curves were obtained in the concentration range 0.1-500 ng/mL. Under the optimum conditions, the limits of detection were obtained in the range 0.007-0.032 ng/mL with satisfactory precision (RSD<6%). The relative recoveries obtained by spiking organochlorine pesticides in water and selected juice samples were in the range of 91.56–99.83%. The sorbent sol-gel poly(ethylene glycol)-poly(propylene glycol)-poly(ethylene glycol) was applied for the extraction and preconcentration of organochlorine pesticides in aqueous and fruit juice samples prior to analysis with gas chromatography-mass spectrometry. The results demonstrated that the present method is simple, rapid, and precise for the determination of organochlorine pesticides in aqueous samples.

Simulation programs contain Computational Fluid Dynamics - CFD codes and are a useful tool used for gas flow through porous materials. Conducting numerical simulations allows for detailed analysis of hydrodynamic phenomena. The results of numerical modeling should always be verifiable based on experimental data. Only their compliance with the results of experimental tests is a determinant of the correctness of the applied method. As part of the work, experimental studies of hydrodynamics of gas flow through an isotropic porous material were carried out and numerical simulation for material of the same shape was used. In the CFD modeling Kolmogorov's hypothesis for the transport of kinetic energy of turbulence k and transport of dissipation rate of kinetic energy of turbulence ε was used.