Hydrogen storage in general is an indispensable prerequisite for the introduction of a hydrogen energy based infrastructure. In this respect, high-pressure metal hydride (MH) tank systems appear to be one of the most promising hydrogen storage techniques for automotive applications using proton exchange membrane (PEM) fuel cells. These systems bear the potential of achieving a beneficial compromise of comparably large volumetric storage density, a wide working temperature range, comparably low liberation of heat, and increased safety. The debatable term unstable metal hydride stands in the literature short for metal hydrides with high dissociation pressure at comparably low temperature. Such compounds may help to improve the merit of high-pressure MH tank systems. Consequently, in the last few years, some materials for possible on-board applications in such tank systems have been developed. This review summarizes the state-of-the-art developments of these metal hydrides, mainly including intermetallic compounds and complex hydrides and gives some guidelines for future developments. Since typical laboratory hydrogen uptake measurements are limited to 200 bar, a possible threshold for defining unstable hydrides could be a value of their equilibrium pressure of peq > 200 bar for T < 100°C. However, these values would mark a technological future target and most current materials, and those reported in this review, do not fulfill these requirements and need to be seen as current stages of development towards the intended target. For each of the aforementioned categories in the review, special care was taken not only to covers the pioneering and classical research, but also to portrait the current status and latest advances. For intermetallic compounds, key aspects focus on the influence of partial substitution on absorption/desorption plateau pressure, hydrogen storage capacity and hysteresis properties. For complex hydrides, the preparation procedures, thermodynamics and theoretical calculation are presented. Besides, challenges, perspectives, and development tendency of this field are also discussed.

Inorganic chemistry has contributed to the progress of human civilization in several different ways. Its activities at the interface with other scientific disciplines has led to emergence of several new fields like organometallic chemistry, bio-inorganic chemistry, solid-state chemistry, environmental chemistry, etc. In the past few decades, it has made inroads in yet another dimension of immense relevance, i.e. nano-science and –technology. In this assay an attempt has been made to present an overview of utility of inorganic and organometallic compounds as precursors for the synthesis of nano-materials with reference to catalysis and materials science. Applications of metal nanoparticles (NPs) and metal chalcogenide NPs, generated through molecular precursor route, in catalysis have been discussed. Synthesis of ternary and quaternary metal chalcogenide nano-materials by molecular precursor route has been reviewed.

With the ever-growing geopolitical tensions across borders arising, ultimately from the eternal energy needs, it is the peak time for humanity to put its reliance on a more quasi-perpetuity source of energy, such as the Sun. Even though current photovoltaics are the frontier of solar power harvesting, their efficiencies are reaching a state of stasis sooner or later. The efficiencies of single-junction solar cells are capped by the Shockley-Quiesser limit of 33.7%. Researchers are racing toward a way to beat this limit while keeping the Levelized Cost of Energy (LCE) to its minimum. Amongst all contenders, rectenna (or rectifying antenna), which was invented only a decade after the first practical PV cell by the Bells lab [1], is the most promising technology to take the forefront in quenching the energy needs, not only because of the absence of any such theoretical limit but also a lower cost of production. This report will review three state-of-the-art architectures for optical rectification developed by the leading groups worldwide. The review will compile a concise discussion on Metal-Double-Insulator-Metal diodes, CNT-Insulator-Metal diodes, and Point-contact-Metal-Insulator-Metal diodes, with an elaborative focus on their fabrication methods and results obtained.

In this article, metallic additive manufacturing (AM) processes were classified and demonstrated. AM technology can be applied to a wide range of industrial areas because of its great feasibility in the design and manufacturing of various complex parts. The main factor that distinguishes various metallic AM processes from each other is the deposition method. Deposited metal can be imported in the form of melt or semi-solid. AM technology also covers a wide range of materials like aluminum, titanium, and many other alloys. Some of the common applications of metallic AM processes are the quick manufacturing of the parts which utilized in various industries like medical, automotive, aerospace, and jewelry industries. AM can help to fabricate parts that are impossible to be manufactured by other processes.

Novel Ca3(BTC)2 metal-organic frameworks with different sizes and shapes constructed by Ca2+ and trimesic acid as metal center and ligands respectively were synthesized by a surfactant-assisted method. The relationship between the quantity of surfactant and the particle morphology of the product have been further studied. The samples were characterized by scanning electron microscope, powder X-ray diffraction and Inductively coupled plasma mass spectrometry. The results indicated that the size and shape of Ca3(BTC)2 could be regulated by changing the quantity of surfactant. Rod- and sheet-like Ca3(BTC)2 MOFs have been readily availabled. The removal kinetics of heavy metals of Pb(II) were also studied by rod-like Ca3(BTC)2. The results showed that as-synthesized Ca3(BTC)2 could effectively remove heavy metals of Pb(II) from the sewage.

Dimers and oligomers of alkenes represent a category of compounds that are in great demand for diverse industrial sectors. Among the developing synthetic methods, the catalysis of alkene dimerization and oligomerization using transition metal salts and complexes is of undoubted interest for practical application. This approach demonstrates substantial potential, offering not only elevated reaction rates but also precise control over the chemo-, regio-, and stereoselectivity of the reactions. In this review, we discuss the data on catalytic systems for alkene dimerization and oligomerization. Our focus lies in the analysis of how the activity and chemoselectivity of these catalytic systems are influenced by various factors, such as the nature of the transition metal, the ligand environment, the activator, and substrate structure. Notably, the review particularly discusses the reaction mechanisms, encompassing metal complex activation, structural and dynamic features, and the reactivity of hydride intermediates, which serve as potential catalytically active centers in alkene dimerization and oligomerization.

Metal/metal composites represent a particular class of materials showing innovative mechanical and electrical properties. Conventionally, such materials are produced by severely plastically deforming two ductile phases via rolling or extruding, swaging, and wire drawing. This study presents the feasibility of producing metal/metal composites via a capacitive discharge-assisted sintering process named electro-sinter-forging. Two different metal/metal composites with CP-Ti/AlSi10Mg ratios (20/80 and 80/20 %vol) are evaluated, and the effects of the starting compositions on the microstructural and compositional properties of the materials are presented. Bi-phasic metal/metal composites constituted by isolated α-Ti and AlSi10Mg domains with a microhardness of 113 ± 13 HV_0.025 for the Ti20-AlSi and 244 ± 35 HV_0.025 for the Ti80-AlSi are produced. The effect of the applied current is crucial to obtain high theoretical density, but too high currents may result in Ti dissolution in the Ti80-AlSi composite. Massive phase transformations due to the formation of AlTiSi based intermetallic compounds are observed through thermal analysis and confirmed by morphological and compositional observation. Finally, a possible explanation for the mechanisms regulating densification is proposed accounting for current and pressure synergistic effects.

Herein, a novel cavity design of racetrack integrated circular cavity established on metal-insulator-metal (MIM) waveguide is suggested for refractive index sensing application. Over the past few years, we have witnessed several unique cavity designs to improve the sensing performance of the plasmonic sensors created on the MIM waveguide. The optimized cavity design can provide the best sensing performance. In this work, we have numerically analyzed the device design by utilizing the finite element method (FEM). The small variations in the geometric parameter of the device can bring a significant shift in the sensitivity and FOM of the device. The best sensitivity and FOM of the anticipated device are 1400 nm/RIU and ~12.01, respectively. We believe that the sensor design analyzed in this work can be utilized in the on-chip detection of biochemical analytes.

In a constantly changing environment brought about by the climate crisis and escalated anthropogenic perturbations driven by the growing population, harmful algal bloom dynamics and their impacts are expected to shift, necessitating adaptive management strategies and comprehensive research efforts. Similar to primary productivity, HABs have been thought to be driven primarily by major nutrients such as N, P, and Si. However, recent investigations on the role and importance of micronutrients as limiting factors in aquatic environments have been highlighted. This paper provides a review of metal and phytoplankton interactions, with a specific emphasis on pertinent information on the influence of trace nutrients on growth, toxin production, and other underlying mechanisms related to the dynamics of HABs. Low to near-depleted levels of essential nutrients including Fe, Cu, Zn, Se, Mn, Co, and Mo, negatively impact cell growth and proliferation of various marine and freshwater HAB species. However, evidence shows that at elevated levels, these trace elements along with other non-essential ones, could still cause toxic effects to certain HAB species manifested by decreased photosynthetic activities, oxidative stress, ultrastructure damage, and cyst formation. Interestingly, while elevated levels of these metals mostly result in increased toxin production, Co (i.e., yessotoxins, gymnodimine, and palytoxins) and Mn (i.e., isodomoic acid, okadaic and diol esters) enrichments revealed otherwise. In addition to toxin production, releasing dissolved organic matter (DOM) including dissolved organic carbon (DOC) and humic substances was observed as an adaptation strategy, since these organic compounds have been proven to chelate metals in the water column, thereby reducing metal-induced toxicity. Whilst current research center on free metal toxicity of specific essential elements such as in Cu and Zn, a comprehensive account of how trace metals contribute to the growth, toxin production, and other metabolic processes under conditions reflective of in-situ scenarios of HAB-prone areas, would yield new perspectives on the roles of trace metals in HABs. With the growing demands of the global population for food security and sustainability, substantial pressure is exerted on the agriculture and aquaculture sector, highlighting the need for effective communication of information regarding the interactions of macro- and micronutrients with HABs to improve existing policies and practices.

Electroless etching of semiconductors was elevated to an advanced micromachining process by the addition of a structured metal catalyst. Patterning of the catalyst by lithographic techniques facilitates the patterning of crystalline and polycrystalline wafer substrates. Galvanic deposition of metals on semiconductors has a natural tendency to produce nanoparticles rather than flat uniform films. This characteristic makes possible the etching of not only wafers but also particles with arbitrary shape. While it has been widely recognized that spontaneous deposition of metal nanoparticles can be used in connection with etching to porosify wafers, it is also possible to produced nanostructured powders. MACE can be controlled to produce (1) etch track pores with shapes and sizes closely related to the shape and size of the metal nanoparticle, (2) hierarchically porosified substrates exhibiting combinations of large etch track pores and mesopores, and (3) nanowires with either solid or mesoporous cores. This review discussed the mechanisms of porosification, processing advances and the properties of the etch product with special emphasis on the etching of silicon powders.

Serum transferrin (sTf) plays a pivotal role in regulating iron biodistribution and homeostasis within the body. The molecular details of sTf Fe(III) binding, blood transport, and cellular delivery through transferrin receptor-mediated endocytosis are generally well-understood. Emerging interest exists in exploring sTf complexation of nonferric metals as it facilitates the therapeutic potential and toxicity of several of them. This review explores recent X-ray structural and physiologically relevant metal speciation studies to understand how sTf partakes in the bioactivity of key non-redox active hard Lewis acidic metals. It challenges preconceived notions of sTf structure function correlations that were based exclusively on the Fe(III) model by revealing distinct coordination modalities that nonferric metal ions can adopt and different modes of binding to metal-free and Fe(III)-bound sTf that can directly influence how they enter into cells and, ultimately, how they may impact human health. This knowledge informs on biomedical strategies to engineer sTf as a delivery vehicle for metal-based diagnostic and therapeutic agents in the cancer field. It is the intention of this work to open new avenues for characterizing the functionality and medical utility of nonferric-bound sTf and to expand the significance of this protein in the context of bioinorganic chemistry.

This article will briefly review the progress of h-BN based solid-state metal semiconductor metal (MSM) neutron detectors. In the last decade, several groups have been working on hexagonal boron nitride (h-BN) based solid-state neutron detectors. Recently, the detection efficiency of 59% has been reported. Efficient, low-cost neutron detectors made from readily available materials are essential for various applications. Neutron detectors are widely used to detect fissile materials and nuclear power plants for security applications. The most common and widely used neutron detectors are 3He based, which are sometimes bulky, difficult to transport, have high absorption length, need relatively high bias voltage (>1000 V), and have low Q-value (0.764 MeV). Also, 3He is not readily available material. Thus, there is a strong need to find an alternative detection material. 10B isotope has a high neutron absorption cross-section, and it has been tested as a coating on the semiconducting materials. Due to the two-step process, neutron capture through 10B, and then electron-hole pair generation in a typical semiconducting material, the efficiency of these devices is not up to the mark. The progress in h-BN based detectors requires a review to envision the further improvement in this technology.

Using two metal insulated metal waveguides (MIM) and five resonator (a quadrilateral cavity and three rings with different dimensions), we design a plasmonic refractive index sensor. Using the time domain finite difference method, we examine and analyze the sensor performance (numerical analysis) and using the transmission line model method, we theoretically examine the performance of the sensor By summarizing these two methods and calculating the sensitivity coefficient S, quality coefficient Q and figure of merit (FOM), a plasmonic sensor with good performance is obtained. Using the supermods of the resonators, we will achieve a stable wavelength spectrum and a suitable and stable sensitivity coefficient spectrum. Challenges and changes that occur in different modes of this sensor will lead to a balanced and relatively good structure. This designed sensor can be useful in the development of integrated optical circuits.

In this paper, a plasmonic refractive index sensor based on metal insulated metal waveguide (MIM) with three rings and a resonant cavity is first proposed and numerically evaluated. Next, we add four teeth to the sensor structure. We study and simulate the resonant wavelengths and refractive index of resonators using the time difference finite difference method. Given that the sensor and the conduction characteristics of plasmonic waves are influenced by the structure parameters,Therefore, by changing the refractive index and changing the dimensions and coordinates of the cavity and rims, we can change the passage coefficient in the resonant modes and measure the sensor performance. As a result, we obtain the sensitivity coefficient, the figure of merit (FOM) and the quality factor Q of the sensor. We modulate the resonance wavelength FWHM using the generated modes and reach a sensitivity of 2166 nm / RIU. These plasmonic sensors with a simple framework and balanced performance and high optical resolution can be used to measure the refractive index in the medical, chemical and food industries.

In this study, we seek to analyze and numerically evaluate a plasmonic sensor. To form the sensor structure, we use several amplifiers, such as two rings attached to each other and a cavity, as well as two metal insulating metal waveguides (MIM). At the beginning of this simulation, we must examine the resonant wavelengths and the refractive index of the resonators using the finite difference time domain method. By changing the refractive index and changing the dimensions of the cavity and the rims, we seek to investigate the sensor performance and the conduction characteristics of the plasmonics and to obtain the effect of these parameters. To evaluate the sensor performance, we calculate the three factors of sensitivity coefficient S, quality factor Q and figure of merit (FOM), here we reach the sensitivity of 987.6 nm / RIU. Such a plasmonic sensor with a simple framework and high optical resolution can be very useful for sensor systems on optical circuits.

In recent years, many researchers have begun to shift their focus onto the synthesis of nanomaterials as this field possesses immense potential that may provide incredible technological advances in the near future. The downside of conventional synthesis techniques, such as co-precipitation, sol-gel and hydrothermal methods, is that they necessitate the use of toxic chemicals, produce harmful by-products and require a considerable amount of energy; therefore, more sustainable fabrication routes are sought after. Biological molecules have been previously utilised as precursors to nanoparticle synthesis, thus eliminating the negative factors involved in traditional methods. In addition, transition-metal nanoparticles possess a wide scope of applications due to their multiple oxidation states and large surface areas; thereby allowing for a higher reactivity when compared to their bulk counterpart and rendering them an interesting research topic. However, this field is still relatively unknown and unpredictable. Therefore, this review aims to obtain a better understanding on the plant-mediated synthesis process of the major transition-metal and transition-metal oxide nanoparticles, and how different parameters affect their unique properties.

Metal additive manufacturing (AM) has gained much attentions in recent years due to its advantages including geometric freedom and design complexity, appropriate to a wide range of potential industrial applications. However, conventional metal AM methods have high-cost barriers due to the initial cost of the capital equipment, support and maintenance, etc. This study presents a unique low-cost metal material extrusion (MME) technology. The filaments used have polylactic acid (PLA) as the matrix and metal powders (copper, bronze, stainless steel, high carbon iron, and aluminum) as reinforcements. Using the proposed fabrication technology, test specimens were built by extruding polymer/metal composite filaments, which were then sintered in an open-air furnace to produce solid metallic parts. In this research, the mechanical and thermal properties of the built parts are examined using tensile tests, thermogravimetric-, thermomechanical- and microstructural analysis.

Metals are particularly sensitive to some pollutant gases. Many museum showcases and store rooms present atmospheres that can corrode cultural heritage artefacts containing metals. Whilst numerous strategies have been reported to mitigate such situations, avoiding them is preferable. Several approaches to testing materials used in construction, fitting out or dressing are used. The relative merits and drawbacks will be discussed. Several parameters of the most widely used, the accelerated corrosion ‘Oddy’ test have been investigated. The influence of abrasive on subsequent corrosion of lead and copper coupons have been assessed. Quantification methods for tested coupons are reviewed. The influence of test duration and temperature were assessed through comparison with real life, long term experience of materials behaviour. Direct contact tests with the material tested touching the test material has been investigated. Several materials present in artefacts are known to potentially cause corrosion when enclosed with metals in other artefacts. A number of situations have been investigated with pollution and RH and some corrosion rate measurements. Ways to isolate artefacts or mitigate are explored and a decision support model has been developed.

This research was conducted to analyze the content of Fe, Cu, Cd, Cr, and Pb in several species of fish taken from three lakes that is closely to disposal of industrial waste in Indonesia. The fish samples were taken from three lakes, namely, Muara Angke, Weda, and Morowali. The samples from Morowali were analyzed in April 2019, those from Weda from November to December 2019, and those from Muara Angke in June 2018. All the samples were then analyzed at the chemistry laboratory of the Department of Chemistry, Faculty of Mathematics and Natural Science, University of Indonesia, and the Integrated Laboratory of IPB. The results showed that all types of fish from Morowali and Weda were no longer safe to consume because they contained Fe, Cu, Cd, and Cr exceeding the threshold of metal contamination. Meanwhile, all types of fish from Muara Angke, except for ayam-ayam, are still safe for consumption. The results of this study can be a source of information regarding metal content in fish and fish feed for safe consumption. Several studies have been done to determine the metal pollutants contained by fish. Given the high consumption rate of fish and the hazards of heavy metals on humans’ health, such research must be furthered

Gasca D herbal formulation is an antidiabetic medicine for the management of diabetes mellitus produced exclusively from natural ingredients. The level of some essential elements (Copper, chromium, Cobalt, Iron, Manganese, Nickel and zinc) and toxic (Cadmium, Arsenic, Mercury, and Lead) heavy metals were determined using microwave plasma-atomic emission spectrometry (MP-AES). The aim of this study is to evaluate the levels of essential and toxic heavy metals and also identify bioactive compounds present in Gasca D herbal formulation. The result shows no traces of Lead, Mercury, Zinc, Arsenic and Zinc, Iron was found to have highest concentration 67.16 + 7.5 µg/g and Cadmium lowest concentration 0.4 + 0.03µg/g. GC-MS analysis of Gasca D herbal formulation revealed the presence of 14 biologically active compounds which include N-Formyl-beta-alanine, Paromomycin, 3,4-Altrosan, Benzamide, 1,3,4-Thiadiazol-2-amine, Carbamodithioic acid, Carbonic acid, alpha-D-Glucopyranoside, Ethyl isocyanide, 2-Propanesulfinic acid, Propanamide, 2-Butenenitrile, Dicyclopropyl carbinol, Isoxazolidine, 1,5-Hexadiene 10-Azido-1-decanethiol. Conclusion: The result indicates that the mean levels of toxic metals in Gasca D herbal formulation were below WHO permissible levels. Gasca D herbal formulation also contains various bioactive compounds that can have various medicinal application which can be used for the treatment of various diseases.

Based upon Maxwell's equations, it has long been established that oscillating electromagnetic (EM) fields incident upon a metal surface decay exponentially inside the conductor, leading to a virtual EM vacuum at sufficient depths. Magnetic resonance imaging (MRI) utilizes radiofrequency (r.f.) EM fields to produce images. Here we present the first visualization of a virtual EM vacuum inside a bulk metal strip by MRI, amongst several novel findings. We uncover unexpected MRI intensity patterns arising from two orthogonal pairs of faces of a metal strip, and derive formulae for their intensity ratios, revealing differing effective elemental volumes (voxels) underneath these faces. Further, we furnish chemical shift imaging (CSI) results that discriminate different faces (surfaces) of a metal block according to their distinct nuclear magnetic resonance (NMR) chemical shifts, which holds much promise for monitoring surface chemical reactions noninvasively. Bulk metals are ubiquitous, and MRI is a premier noninvasive diagnostic tool. Combining the two, the emerging field of bulk metal MRI can be expected to grow in importance. The fundamental nature of results presented here may impact bulk metal MRI and CSI across many fields.

The cutting-edge photovoltaic cells are an indispensable part of the ongoing progress of earth-friendly plans for daily life energy consumption. However, the continuous electrical demand that extends to the night time requires a prior deployment of efficient real-time storage systems. In this regard, metal-air batteries have presented themselves as the most suitable candidates for solar energy storage, combining extra lightweight with higher power outputs and promises of longer life cycles. Scientific research over non-precious functional catalysts has always been the milestone and still contributing significantly to exploring new advanced materials and moderating the cost of both complementary technologies. Metal-organic frameworks (MOFs) derived functional materials have found their way to the application as storage and conversion materials, owing to their structural variety, porous advantages, as well as the tunability and high reactivity. In this review, we provide a detailed overview of the latest progress of MOF-based materials operating in metal-air batteries and photovoltaic cells.

A useful and increasingly common additive manufacturing (AM) process is the selective laser melting (SLM) or direct metal laser sintering (DMLS) process. SLM/DMLS can produce full-density metal parts from difficult materials, but it tends to suffer from severe residual stresses introduced during processing. This limits the usefulness and applicability of the process, particularly in the fabrication of parts with delicate overhanging and protruding features. The purpose of this study was to examine the current insight and progress made toward understanding and eliminating the problem in overhanging and protruding structures. To accomplish this, a survey of literature was undertaken, focusing on process modeling (general, heat transfer, stress and distortion, and material models), direct process control (input and environmental control, hardware-in-the-loop monitoring, parameter optimization, and post-processing), experiment development (methods for evaluation, optical and mechanical process monitoring, imaging, and design-of-experiments), support structure optimization, and overhang feature design; approximately 140 published works were examined. The major findings of this study were that a small minority of the literature on SLM/DMLS deals explicitly with the overhanging stress problem, but some fundamental work has been done on the problem. Implications, needs, and potential future research directions are discussed in-depth in light of the present review.

Composite polymolecular separation membranes were prepared by combining multi-branched ZIF-L with high porosity electrospinning nanofibers PI. Meanwhile, PDA and PEI were introduced into the membrane in order to improve its adhesion. The new membrane is so called “PI@PDA@PEI/ZIF-L-4” composite membrane; compared with PI@PDA@PEI/ZIF-8 composite membrane, the new membrane’s filtration rates for heavy metal ions such as Cd2+, Cr3+ and Pb2+ were increased by 7.0%, 6.6% and 9.3%, respectively. Furthermore, the new membrane has a permeability up to 1,140.0 L·m−2·h−1·bar−1, and were presenting a very stable performances after four repeated uses. The separation mechanism of PI@PDA@PEI/ZIF-L composite membranes was further analyzed in order to provide a base support for producing separation membranes with high barrier rate and high flux.

The transferability of structure-property relationships for laser-pretreated metal adhesive joints to laser-pretreated metal – carbon fiber reinforced plastic (CFRP) bonds is investigated. Single-lap shear tests were performed on hybrid AW 6082-T6 – CFRP specimens pretreated with the same pulsed laser surface parameter sets on the metal surface as previously tested AW 6082-T6 – E320 metal adhesive joints. The fracture surfaces were characterized to determine the type of failure and elucidate differences and commonalities in the link between surface structures and single-lap shear strengths. Digital image analyses of the hybrid specimens fractured surfaces were used to quantify remaining CFRP fragments on the metallic joint side. The results indicate that high surface enlargements and the presence of undercut structures leads to single-lap shear strengths exceeding 40 MPa and 35 MPa for unaged and aged hybrid specimens respectively. While for the metal-polymer joints the trend from high strength to weakly bonded specimens was largely continuous with the degree of surface structuring, hybrid metal – CFRP joints exhibit a drastic drop in joint performance after aging if the laser-generated surface structures are less pronounced with low surface enlargements and crater depths. Surface features and hydrothermal aging determine whether the specimens fail cohesively or adhesively.

Peptides, both natural and synthetic, are well suited for a wide range of purposes and offer versa-tile applications in different fields such as biocatalysts, injectable hydrogels, tumor treatment, and drug delivery. The rising prominence of therapeutic peptides encompasses anticancer, antiviral, antimicrobial, and anti-neurodegenerative properties. The metals Na, K, Mg, Ca, Fe, Mn, Co, Cu, Zn, and Mo are ten of the twenty elements that are considered essential for life. Crucial for under-standing the biological role of metals is the exploration of metal-bound proteins and peptides. Aside from essential metals, there are other, non-essential metals that also interact biologically, exhibiting either therapeutic or toxic effects. Irregularities in metal binding contribute to diseases like Alzheimer’s, neurodegenerative disorders, Wilson's, and Menkes disease. Certain metal com-plexes have potential applications as radiopharmaceuticals. The examination of these complexes was done by preforming UV-Vis, IR, EPR, NMR spectroscopy, and X-ray analysis.

We studied surface enhanced Raman spectra of amino acids D-alanine and DL-serine and their mixture on silver nanoisland films (SNF), immersed in phosphate buffer saline solution at millimolar amino acid concentrations. It is shown that the spectra from the amino acid solutions differ from the reference spectra for microcrystallites due to electrostatic orientation of amino acid zwitterions by the metal nanoisland film. Moreover, non-additive peaks are observed in the spectrum of the mixture of amino acids adsorbed on SNF, which means that intermolecular interactions between adsorbed amino acids are very significant. The results indicate the need for a thorough analysis of the Raman spectra from amino acid solutions in the presence of a nanostructured metal surface, and may also be of interest for studying molecular properties and intermolecular interactions.

In this work, a ZIF-67/MWCNTs/Nafion sensor platform was constructed based on the good adsorption capacity of ZIF-67, the electrical conductivity of multiwalled carbon nanotubes (MWCNTs) and the excellent chemical stability of Nafion for the detection of Cu2+ in water. Meanwhile, the modified materials were characterized by scanning electron microscopy (SEM), Transmission electron microscopy (TEM), BET specific surface area test, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and Fourier transform infrared spectrometry (FT-IR). Cyclic voltammetry (CV), electrochemical impedance (EIS), and square wave solvation voltammetry (SWSV) electrochemical methods were used to perform applied test studies on ZIF-67/MWCNTs/Nafion/GCE. The results show that ZIF-67/MWCNTs/Nafion/GCE has high sensitivity (57.5 μA/μM) and a low limit of detection (15.0 nM) for the electrochemical detection of Cu2+ ions in an electrochemical sensing system. It has high adsorption selectivity for Cu2+, and the recovery of Cu2+ in real water reached 98.6%-103%. The modified electrode has good repeatability, reproducibility, anti-interference, and stability, which makes this sensing platform can be practically applied to the detection of domestic water.

Dendrite growth and parasitic reactions with liquid electrolyte are the two key factors that restrict the practical application of the lithium metal anode. Herein, a bis(benzene sulfonyl)imide based single-ion polymer artificial layer for lithium metal anode is successfully constructed, which is prepared via blending the as-prepared copolymer of lithiated 4, 4’-dicarboxyl bis(benzene sulfonyl)imide and 4,4’-diaminodiphenyl ether on the surface of lithium foil. This single-ion polymer artificial layer enables compact structure with unique continuous aggregated Li+ clusters, thus reducing the direct contact between lithium metal and electrolyte, and ensuring Li+ transport fast and homogeneous simultaneously. Based on which, the coulombic efficiency of the Li|Cu half-cell is effectively improved, and the cycle stability of the Li|Li symmetric cell can be prolonged from 160 h to 240 h. Surficial morphology and elemental valence analysis confirm that the bis(benzene sulfonyl)imide based single-ion polymer artificial layer effectively facilitates the Li+ uniform deposition and suppresses parasitic reactions between lithium metal anode and liquid electrolyte in the LFP|Li full-cell. This strategy provides a new perspective to achieve steady lithium metal anode, which can be a promising candidate in practical application.

With this article, impact of effluent mixed water with the quality of the Mansagar Lake has been established by evaluating the physico-chemical parameters and the heavy-metal contents experimentally. The process of calculating water quality and the metal pollution quality indices is also explained in brief with respect to selected sample locations and varied environmental conditions (Pre- and Post-Monsoon season). Distribution trends of Pearson‘s correlation factor have also been discussed to establish their relation among the physico-chemical parameters and the heavy-metal contents for varied environmental conditions. In the end, detailed discussion on observations made during this study and useful recommendations are also elaborated in details. With this article, we intend to present a document for better understanding of the water quality of this lake in view of futuristic management strategies to be adopted to maintain it heritage values.

The efficiency of cold sheet and strip rolling of steels and non-ferrous metals in the main depends on the quality of the technological lubricant and its cost. In this regard, it is important to develop new compositions of effective metal-working coolants (MWC) having low cost and providing the maximum reduction in the friction coefficient. We developed and tested the new compositions of the MWC on basis of chicken fat, and mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 260 mm during steel 08Kp rolling. The efficiency of the coolants was determined by the factor of metal stretch forming λ and the coefficient of friction μ in the deformation zone which was found by forward slip method. We found the metal-working coolant with 100 % concentration of boric acid esters of mono- and diglycerides is the most effective in steel rolling. Thus the new MWC on basis of boric acid esters of mono- and diglycerides synthesized from the wastes of sunflower oil production can be recommended for use in rolling of structural steels on account of availability, high efficiency, and a low cost.

Metal additive manufacturing (AM), commonly referred to as 3D printing with metals, is an innovative technology with significant potential to transform industries such as aerospace, automotive, and healthcare. Despite its promise, the field faces several challenges that impact both its technical feasibility and economic viability. This paper explores the primary technical challenges, including material properties and processing complexities, such as the need for precise control of thermal gradients and the mitigation of defects like porosity and residual stresses. Additionally, it addresses the economic barriers, including high initial equipment costs, the need for specialized knowledge, and the relatively slow build speeds compared to traditional manufacturing methods. By examining these challenges, this paper aims to provide a comprehensive overview of the current state of metal additive manufacturing and suggest potential pathways for overcoming these obstacles to facilitate wider adoption and technological advancement in the field.

Toxic metal wastewater is a challenge for exposed terrestrial, aquatic environments and the recyclability of the water, prompting inputs for the development of promising treatment methods. Consequently, the rGO/ZnONP nanocomposite was synthesized at room temperature for four hours and was tested for adsorption of cadmium and lead in wastewater. The optimized nanocomposite had the lowest band gap energy (2.69 eV) and functional group interactions were at 516, 1220, 1732, 3009, and 3460 cm-1. The nanocomposite showed saturation of ZnO nanoparticles on rGO with a weight percentage of zinc (60.02 %), oxygen (22.96 %), and carbon (16.58 %), and the micrograph showed slight agglomeration on the sheet surface. The nanocomposite’s D and G band intensities were almost the same constituting the ZnO presence on rGO from the raman spectrum. The adsorption equilibrium time for cadmium and lead was reached within 10 and 90 minutes with efficiencies of ~ 100 %. Sips and Freundlich were best fitting the cadmium and lead adsorption data (R2 ~ 1), therefore the adsorption was a multilayer coverage for lead and a mixture of heterogenous and homogenous coverage for cadmium adsorption. Both adsorptions were best fitted by the pseudo first order model, suggesting the multilayer coverage dominance. The adsorbent was reused for three and seven times for cadmium and lead. The nanocomposite showed selectivity towards lead (95 %) and cadmium (100 %) in the interfering wastewater matrix. Conclusively, the nanocomposite may be embedded within upcoming lab-scale treatment plants which could lead to further upscaling and serving as industrial wastewater treatment material.

Wastewater contaminated with antibiotics is a major environmental challenge. We developed here the green synthesis of bio-graphenes by using natural precursors (Xanthan, Chitosan, Boswellia, Tragacanth). The use of these precursors can act as templates to create 3D doped graphene structures with special morphology. Also, this method is a simple method for in-situ synthesis of doped graphenes. The elements present in the natural polymers (N) and other elements in the natural composition (P, S) are easily placed in the graphene structure and improve the catalytic activity due to the structural defects, surface charges, increased electron transfers, and the high absorption. In this mechanism, O2 dissolved in water absorbs onto the positive charged C in doped graphenes to create oxygenated radicals, which enables the degradation of antibiotic molecules. Light irradiation increases the amounts of radicals and rate of antibiotic removal. The results have shown that the hollow cubic Chitosan-derived graphene has shown the best performance due to the doping of N, S, and P. The Boswellia-derived grapheme shows the highest surface area, but lower catalytic performance, which indicates the more effective role of doping in the catalytic activity. The effect of oxygen and light were also studied to accelerate the degradation process.

: AlF3 has interesting electrophysical properties, due to which the material is promising for applications in supercapacitors, UV coatings with low refractive index, excimer laser mirrors, and photolithography. The formation of AlF3-based nano- and micro-wires can bring new functionalities to AlF3 material. AlF3 nanowires be used, for example, in functionally modified microprobes for scanning probe microscopy. In this work, we investigate the AlF3 samples obtained by the reaction of initial aluminum with aqueous hydrofluoric acid solution of different concentrations. All the samples were obtained under normal conditions. The morphology of the nanowire samples is studied by scanning electron microscopy. Quantitative energy-dispersive x-ray spectroscopy (EDS) spectra are obtained and analyzed with respect to the feedstock and each other.

: AlF3 has interesting electrophysical parameters, due to which the material is promising for applications in supercapacitors, UV coatings with low refractive index, excimer laser mirrors, and photolithography. The formation of AlF3-based nano- and micro-wires can bring new functionalities to AlF3 material. AlF3 nanowires be used, for example, in functionally modified microprobes for scanning probe microscopy. In this work, we investigate the AlF3 samples obtained by the reaction of initial aluminum with aqueous hydrofluoric acid solution of different concentrations. All the samples were obtained under normal conditions. The morphology of the nanowire samples is studied by scanning electron microscopy. Quantitative energy-dispersive x-ray spectroscopy (EDS) spectra are obtained and analyzed with respect to the feedstock and each other.

Antioxidants are molecules that neutralize free radicals. In general, the reaction mechanisms of antioxidants are well known. The main reaction mechanisms of antioxidants are electron transfer (ET), proton transfer (PT), H atom transfer (HAT) and radical adduction (RAF). The study of these mechanisms is helpful to understand how antioxidants control high free radical levels on the cell. There are many studies focused on determine the main mechanism of an antioxidant to neutralize a wide spectrum of radicals, mainly reactive oxygen species (ROS) type radicals. Most of these antioxidants are polyphenols type compounds. Some esters, amides and metal-antioxidants have shown antioxidant activity. There are few experimental and theoretical studies about the antioxidant reaction mechanism of the aforementioned compounds. In this work, we shown the reaction mechanism proposed of an amide and its metal-antioxidant counterpart. We show how the presence of the metal increase the electron transfer on polar media and the H transfer in non-polar media. Even though, esters and amides are non-polar compound, the scavenger activity is good for the metal-antioxidant compound in no-polar media

Using agronomic measures to remediate heavy metals on farmland is the main measure to achieve the safe utilization of crops. Investigating the effects of applying different fertilizers on the uptake, and translocation of Chromium (Cr) in maize and on the effectiveness of Cr in soil under Cr contamination of farmland is of great theoretical and practical significance to achieve the safe utilization of arable land and safe production of agricultural products. Under field trial conditions, different fertilizer types were set up, including ammonium sulfite, calcium-magnesium phosphate, and diammonium phosphate. locally formulated fertilizers (urea-ammonium phosphate-potassium chloride) serving as the control, with Biochar and conditioner PX5B were chosen to compare the impacts of each. To study the effects of different fertilizer types on maize yield, Cr content in the plant, bioconcentration factor, translocation factor and available content of Cr in the soil. The results showed that Compared with the formulated fertilizer, all treatments could improve pH, soil organic matter (SOM） and reduce the effective state of Cr content in the soil by 15.05% to 42.66%. While the Cr content of maize grains treated with biochar and conditioner PX5B was 0.80 mg·kg-1 and 0.88 mg·kg-1 with reduction rates of 39.95% and 33.83%, respectively. The Cr content of maize grains treated with various fertilizer treatments ranged from 0.82 to 1.32 mg·kg-1 with reduction rates of 0.75% to 38.19%. The Cr content of maize grains could be brought down to below the national food safety standards of China(1.0 mg·kg-1) using urea – calcium magnesium phosphate - potassium chloride, urea - diammonium phosphate - potassium chloride, ammonium sulfite – calcium magnesium phosphate - potassium chloride and ammonium sulfite, urea – calcium magnesium phosphate - potassium chloride and the two conditioner treatments. Among the different fertilizer treatments, the best fertilizer treatment for reducing the effective state Cr content of soil and the Cr content of maize grains was ammonium sulfite-calcium-magnesium-phosphate fertilizer-potassium chloride, which could achieve similar reductions as the two conditioners, while it also had a certain reduction effect on the Cr content in maize roots and straws and on the aboveground bioconcentration factor（BCF） and the root-to-straw translocation factor（PTF） of maize for Cr. Therefore, the combination of ammonium sulfite and calcium magnesium phosphate is the best fertilizer combination to block the absorption of Cr by maize and has some implications for the fertilization of farmland under acidic soil conditions of Cr contamination.

Heavy metals toxicity is a grave environmental issue in contemporary times. Phytoremediation is economic, effective and ecofriendly approach to decontaminate and remediate metal contaminated areas. Phenolic and Flavonoid content are important abiotic stress markers. The individual and combined impacts of toxiferous metals Arsenic (As), Cadmium (Cd) and (Copper) Cu were employed in recent studies to investigate their effect on Total flavonoids content (TFC) and total phenolic content (TPC) in various parts of Hydrocotyle umbellata L. to explore the role of plant in abating metal contamination. Folin- ciocalteu and AlCl 3 methods were used for investigating TPC and TFC respectively. Two-way ANOVA and CART model were employed for statistical analysis. Highest TPC was examined in decreasing order as leaf &amp; gt; stem &amp; gt; root in case of all the metals. Whereas highest TFC was found in all plant parts when subjected to As toxicity, and the lowest TFC was found in stem of the plant in respect to Cu toxicity. There was significant effect on TPC on plant part when subjected to Cu and As stress, but so significance was observed in plant part in case of Cd and combined metal stress. Treatment concentration had no significant effect on TPC when subjected to unique impact of all the three metals but had significant effect in case of combined metal stress. Similarly, in case of TFC no significant effect was recorded in case of plant part in all the stress types. But treatment amount has significant impact on Cd and combined metal stress. Metal type has significant effect on TPC and TFC. Whereas plant part has significant impact on TPC but non-significant values were observed on TFC in this case. This study epitomizes TPC and TFC in plants as effective and viable tool to pertain their role in phytoremediation against metal contamination. Therefore H. umbellata L. can be exerted for successful assemblage and decontamination of Cd, Cu and As in different plant parts.

Sequential reactions of aminoalkynes represent a powerful tool to easily assembly biologically important polyfunctionalized nitrogen heterocyclic scaffolds. Metal catalysis often plays a key role in terms of selectivity, efficiency, atom economy and green chemistry of these sequential approaches. This review examines the existing literature on the applications of reactions of aminoalkynes with carbonyls which are emerging for their synthetic potential. Aspect concerning the features of the starting reagents, the catalytic systems, alternative reaction conditions and the pathways as well as the possible intermediates are provided.

Abstract: Heavy metals (HMs) contamination is one of the main among abiotic factors affecting crop productivity and also threatens human health via consuming metal contaminated crops as a food source. Over the past few years, HMs have drawn a lot of attention due to their increased use for commercial purposes and their harmful effects on plants and other life forms, thus threatening human survival. However, in recent years, several methods have been adopted to combat the harsh effects of HMs. After phytohormones, use of mineral nutrients such as selenium (Se) in the prevention of HM stress has been explored by the researchers more recently. Selenium is an important micronutrient widely known for its antioxidant properties in both plants and animals. Exogenous Se inhibits metal uptake and its translocation and also improves the antioxidant system, thus imparts resistance to HM toxicity in plants. Moreover, Se also regulates the production of various osmolytes in cells that helps in developing cell osmolarity. Selenium also induces the production of different types of secondary metabolites (SMs) that are also involved in plant's secondary defense mechanisms to different stresses. Uptake of mineral nutrients is a vital process for plant growth and development, which is also positively correlated with Se under metalloid toxicity. However, in order to understand the exact mechanism of Se in HM tolerance, different metabolic processes stimulated by Se and their pathways need to be explored. Hence, this review focuses on the role of Se on nutritional status, antioxidants metabolism, interaction with phytohormones and its role in the regulation of various genes involved in Se induced HM tolerance. Thus, this study will help researchers in the future for the improvement of HM tolerance via Se application in plants.

Co-based catalysts have gained significant attention in recent years due to their excellent ability to activate C-H bonds and high selectivity towards olefins, despite being a non-noble and environmentally unfriendly metal. However, further improvements are necessary for practical utilization, particularly in terms of activity and anti-carbon deposition capacity. In this study, we synthesized Al₂O₃ nanorods with abundant pentacoordinated Al³⁺ (Al³⁺_penta) sites. The supported Co on the Al₂O₃ nanorod (Co/Al₂O₃-NR) exhibited higher selectivity (&gt;96% propylene selectivity) and stability (deactivation rate 0.15 h^-1), compared to Co supported on an Al₂O₃ nanosheet with fewer pentacoordinated Al³⁺ sites. Various characterizations confirmed that Co(II) mainly exists as CoAl₂O₄ rather than Co₃O₄ in the form of Co/Al₂O₃-NR, which inhibits the reduction of Co(II) to Co0 and improves catalyst stability accordingly.

Metal halide perovskites (MHPs), in particular lead-based halide perovskites have earned a recognized fame in several fields for their outstanding optoelectronics properties including direct generation of free charge carriers, optimal ambipolar charge carrier transport properties, high absorption coefficient, point-defect tolerance, and compositional versatility. Nowadays, this class of materials represents a real and promising alternative of silica for the photovoltaic technologies. This worthy success led to a growing interest in the exploration of MHP materials in other hot research fields such as the solar-driven photocatalytic water splitting towards hydrogen production, CO2 reduction to CO and CH4, useful organic reactions such as organic synthesis (formation of C-C, C-N, and C-O bonds), and pollutants and dye degradation. Nevertheless, many of these perovskite materials showed air and moisture instability problems that considerably hinder their practical application for photocatalytic water splitting and photodegradation of CO2. Moreover, if the chemical instability is a problem that can be in part mitigated by the optimization of the lattice structure, the presence of lead represents a real problem for the practical application of these type of materials in commercial devices. To successfully overcome this problem, lead-free metal halide perovskites (LFMHPs) have gained increasing interest thanks to their promising optoelectronic properties, comparable to lead-based materials, and their eco-friendly nature. Among all the lead-free perovskite alternatives, this mini review will focus the attention on the bismuth-based perovskites and perovskite derivatives with specific focus on solar-driven photocatalysis application for H2 evolution.

Heavy metals contamination in groundwater often occurs in various industrial processes. Stud-ies have confirmed that polysulfide could reduce hexavalent chromium to trivalent chromium, achieving the effect of in-situ stabilization. For other heavy metals contamination in groundwa-ter, whether polysulfide also had a stabilizing ability to achieve in-situ remediation. This re-search focused on heavy metals except for chromium that often contaminated in groundwater, including lead, nickel, zinc, copper, and cadmium to explore the feasibility of using calcium polysulfide (CaSx) as an in-situ stabilization technology for these heavy metals contamination groundwater. Results showed that CaSx had a great removal efficiency for heavy metals lead, nickel, zinc, copper, and cadmium. However, for nickel, zinc, copper and cadmium, when CaSx was added excessively, complexes would be formed, causing the result of re-dissolve and this would also reduce the removal efficiency. Since it is difficult to accurately control the dosage of agents for in-situ groundwater remediation, the concentration of re-dissolved nickel, zinc, cop-per, and cadmium may not be able to meet the groundwater control standards. CaSx had high lead removal efficiency, and it would not cause re-dissolution due to excessive CaSx dosing. CaSx can be used as an in-situ stabilization technique for lead contaminated groundwater.

The purpose of this study was to arrange a green roof on a sheet metal house to achieve winter heat preservation and summer thermal insulation using different plants and soil media, and to maintain the advantage of cost-saving and quick installation of sheet metal houses. In terms of the research method, the roof insulation, heat preservation and plant growth index were tested. Plants were grown in 10 container-type green roofs on the sheet metal house roof, and the physical environment of the building was monitored for one year. Five containers of commercially-available culture soil and five containers of sustainable composite were used as the media for growing five kinds of plants, respectively. The control group only had a sheet metal house roof. There were 11 experimental modules for testing whether the green roofs had thermal insulation, heat preservation and plant growth effects on a general sheet metal house. The results showed that, regarding the thermal insulation benefit assessment, the Sedum acre cv. robustum of green roof Groups B to D caused the temperature to be 38.29°C lower than the surface of the simple sheet metal house roof in August, showing a temperature difference of 54%.

This review analyzes the preparation and characterization of metal organic frameworks (MOFs) and their application as photocatalysts for water purification. The study begins by highlighting the problem of water scarcity and the different solutions for purification, including photocatalysis with semiconductors such as MOFs. It also describes the different methodologies that can be used for the synthesis of MOFs, paying attention to the purification and activation steps. The characterization of MOFs and the different approaches that can be followed to learn on the photocatalytic processes are also detailed. Finally, the work reviews literature focused on the degradation of contaminants from water using MOF-based photocatalysts under light irradiation.

The Anderson insulating states in Au nanoparticle assembly are identified and studied under the application of magnetic fields and gate voltages. When the inter-nanoparticle tunneling resistance is smaller than the quantum resistance, the system showing zero Mott gap can be insulating at very low temperature. In contrast to Mott insulators, Anderson insulators exhibit great negative magnetoresistance, inferring charge de-localization in a strong magnetic field. When probed by the electrodes spaced by ~200 nm, they also exhibit interesting gate-modulated current similar to the multi-dot single electron transistors. These results reveal the formation of charge puddles due to interplay of disorder and quantum interference at low temperatures.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

The cement industry has significant environmental impacts, stemming from natural resources extraction and fossil fuels combustion. Notably, carbon dioxide (CO2) emissions are a major concern associated with cement production. The cement industry emits 0.6 tons of CO2 per ton of cement production, which is around 8 % of the total CO2 emissions in the world. Meeting the 13th United Nations Sustainable Goals, cement plants aim to achieve carbon neutrality by 2050, resulting from reduction in CO2 emissions (change in the composition of cementitious materials) and the adoption of carbon capture and utilisation (CCU) technologies. A promising approach involves converting CO₂ into valuable chemicals and fuels, such as methanol (MeOH) through the power-to-liquid (PtL) technologies. In this process, CO2 captured from cement industry flue gas with hydrogen generated from renewable sources through electrolysis of water, catalytically transformed into renewable methanol (e-MeOH), offering a sustainable solution. To achieve this, it is crucial to advance the development of novel, highly efficient catalysts specifically designed for direct CO2 hydrogenation. In this sense, this review discusses recent developments and improvements in CO2 catalytic conversion, emphasizing catalyst performance, selectivity, and stability.

Methyl Mercaptan is a sulfur-based chemical found as a co-product in produced natural gas and causes corrosion in pipelines, storage tanks, catalysts, and solid adsorption beds. To improve the quality of methane produced, researchers studied the use of metal oxides and aluminum silicates as catalysts for removing mercaptan. However, there are restricted limitations on the efficiency of metal oxides or aluminum silicates as adsorbents for this particular application. Therefore, this study investigated the performance of these materials in a fixed-bed reactor with simulated natural gas streams under various operating conditions. The testing procedure includes a detailed assessment of the adsorbent/catalysts by several techniques, such as Braeuer-Emmett-Teller (BET), Scanning Electron Microscope (SEM), Energy-Dispersive X-ray Spectrometry (EDS), and X-ray Photoelectron Spectroscopy. The result revealed that metal oxides such as copper, manganese, and zinc performed well in methyl mercaptan elimination. The addition of manganese, copper, and zinc oxides to the aluminum silicate surface resulted in a sulfur capacity of 1226 mg S/g of catalyst. These findings provide critical insights for the development of catalysts that combine metal oxides to increase adsorption while reducing the production of byproducts like dimethyl sulfide (DMS) and dimethyl disulfide (DMDS) during methyl mercaptan removal.

Anthropogenic activity like Industrialization has unleashed vast quantities of organic pollutants, including heavy metals. The hazardous heavy metals can cause cancer, neurocognitive defects and wide-ranging health problems. The pollutants resist environmental degradation and can often accumulate in the environment. Microbial degradation of pollutants is a potentially efficient solution for pollution remediation. Amongst the heavy metals, lead contamination resulting from anthropogenic activity have resulted in tragic consequences since the advent of human civilization, even in 21^st century as demonstrated by the Flint water crisis in the US. Bioremediation of lead from the environment could be attempted by various strategies, including mitigation of human activity that causes it in the first place. Microbiome, specifically bacteria, mediated bioremediation can serve as a potent platform for remediating environmental pollution with heavy metals such as lead. Herein we will review the mechanisms and methods of microbial bioremediation of environmental heavy metals with a focus on lead and highlight the challenges and opportunities.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage application of automotive field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for trolleybus. The novelty of this work is the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for electrical current collector heads, as well as the character-istics obtained for this material. All 4 obtained materials have been characterized from structural (by optical microscopy), mechanical (density, electrical resistivity, hardness) and functional point of view (wear after 1000 working hours, electric discharge and electric load) and it was determined that the material which uses chemically copper covered graphite is the most suitable of them and has been chosen to be further developed by the end beneficiary.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage applications of automotive and/or aviation field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for electric engines. The novelty of this work is the presentation of the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for current collector heads, as well as the characteristics obtained for this material. All 4 obtained materials have been characterized from structural, mechanical and functional point of view and the most suitable of them has been chosen to be further developed by the end beneficiary.

In this study, Al-Al4C3 compounds were manufactured by mechanical milling followed by heat treatment. To analyze the microstructural evolution, the composites were sintered at 550°C during different sintering times of 2, 4 and 6 hours. The mechanical results suggest that dislocation density and crystallite size primary contribute to hardening before the sintering process, with a minimal contribution from particle dispersion in this condition. The compound exhibited a significant 75% increase in hardness after 2 hours of sintering, primarily attributed to the nucleation and growth of Al4C3 nanorods. The HRTEM analysis, combined with ge-ometric phase analysis (GPA) at and near the Al-Al4C3 interface of the nanorods, revealed strain field distributions primarily associated with partial screw dislocations and the presence of closely spaced dislocation dipoles. These findings are consistent with the microstructural parameters determined from X-ray diffraction pattern analysis using the convolutional multi-ple whole profile (CMWP) method. This analysis showed that the predominant dislocation character is primarily of the screw type, with the dislocation dipoles being closely correlated. Based on these results, it is suggested that samples with a lower weight percentage of rein-forcement and longer sintering times may experience reduced brittleness in Al/Al4C3 compo-sites. Strengthening contributions were calculated using the Langford–Cohen and Taylor equations.

In this review we explore the recent progress in catalytic materials for ammonia synthesis that are based on metal nitrides and other catalytic surfaces. It comprises a detailed overlook of various techniques used in ammonia synthesis research and the state-of-the-art modeling techniques employed to investigate new reaction mechanisms and more efficient processes for sustainable ammonia synthesis production. The review is discussed in the context of reaction mechanisms developed and recent progress that has been made with respect to thermal, electrochemical and photocatalytic ammonia synthesis.

Sustainable soil quality management is one of the most important approaches in ensuring high agricultural productivity and safe quality produce. With the current rising application of inorganic fertilizers and chemical pesticides, degradation of agricultural soils is becoming a global phenomenon, attracting attention of many researchers. The present study hypothesized that with the increasing chemical pesticide and fertilizer application under various cropping systems, there is potential for increased toxicity of heavy metals residues above background concentrations and their associated complexes and intermedia transfer between environmental compartments in large-scale farms in Kenya. Using standard methods, 204 soil samples collected from five distinct cropping systems were analyzed for PH, Electrical Conductivity, exchangeable base cations (Na+, Mg2+, K+, Ca2+), Cu, Pb, Zn, Cd, Fe, Cr, Total Organic Carbon and Total N and data analyzed using Genstart, version 23.1. The concentrations of Zn, Cu, Pb and Fe were lower than the globally acceptable levels hence less soil pollution threat (NPI&lt;1). However, Cd concentration exceeded permitted levels (NPI&gt;1). Among the cropping systems considered, Maize and sugarcane cropping systems were the most susceptible to heavy metal pollution. In conclusion, the rank order of the pollution potential associated with heavy metal contamination in the study area is Cd&gt;Zn&gt;Pb&gt;Cu&gt;Cr&gt;Fe.

This study provides an in-depth review of the available literature on metal composite material machining, focusing on traditional machining operations such as turning, milling, shaping, drilling, and grinding. The motivation for the study is that this composite type has emerged as a vital material in applications requiring functionality, resilience, cost-effective operation, low consumption of energy and lightweight. Despite its superior characteristics, the manufacturing complexity and poor machinability of metal matrix composites have been the primary barriers to its adoption. Nevertheless, there is a reduction of exceptional efficiency, increase in surface roughness, tool wear and so on in metal matrix composites throughout machining. As a result, this review gives a comprehensive investigation of metal matrix composite machining and effect on process parameters and procedures. Furthermore, this study distinguishes metal matrix composites towards sustainable manufacturing and the metals employed by the researchers, as well as the gaps discovered for future recommendations in metal-based composites.

The indole nucleus is an important element of many natural and synthetic molecules with significant biological activity. Nonetheless, the co-presence of transitional metals in organic scaffold may represent an important factor in the development of effective medicinal agents. This review covers some of the relevant and recent achievements in the biological, chemical and pharmacological activity of important indole-based metal complexes in the area of drug discovery.

At this time, nanoparticles used to been considered for various biomedical applications due to their particular properties[1, 2]. It is already known that one of the major advances in the relative application of nanoparticles is the recognition of the steric stabilization which can increase the particle stability in the biological environment and provide the opportunities of the application of nanoparticles in the development of drug delivery systems (DDSs) for achieving drug targeting and controlled drug release. Nano crystalline silver particles (AgNPs) have major applications in biomolecular recognition of highly sensitive, anti-microbial treatment, catalysis and manufacture sensors [3-7]. The NPs for various applications medical like image quality, medicine, tissue, magnetic resonance imaging (MRI) of targeting tissues and cells styles. This is particularly the case of AgNPs significantly encompasses the whole a wide range of industrial and medical applications. In this study, we have been synthesized incorporated omeprazole and omeprazole sulfide drugs with AgNPs and the results was investigated with TEM, FT-IR, DRS and XRD. The particle size has been seen in imaging TEM about 80 nm. Moreover either Omeprazole@AgNPs or omeprazole sulfide@AgNPs are able to excrete bacteria. In this study, the antibacterial properties of drugs with silver nanoparticles also increased.

Hydrogen energy is regarded as an auspicious future substitute to replace fossil fuels, because of its environmentally friendly characteristics and high energy density. In the pursuit of clean hydrogen production, there has been a significant focus on the advancement of effective electrocatalysts for the process of water splitting. Although noble metals like Pt, Ru, Pd and Ir are superb electrocatalysts for the hydrogen evolution reaction (HER), they have limitations for large-scale applications, mainly high cost and low abundance. As a result, non-precious transition metals have emerged as promising candidates to replace their more expensive counterparts in various applications. This review focuses on recently developed transition metal phosphides (TMPs) electrocatalysts for the HER in alkaline media due to the cooperative effect between the phosphorus and transition metals. Finally, we discuss the challenges of TMPs for HER.

Early debridement and stabilization for pyogenic spondylodiscitis allow early mobilization of the patient and prevent subsequent spinal deformity. Tantalum (Ta) trabecular metal (TM) components have several potential advantages over conventional implant materials, such as its uniformity and structural continuity, strength, low stiffness, high porosity, high coefficient of friction and tantalum trabecular metal enhances the host defense mechanism by increasing leukocyte chemotaxis, phagocytosis, and the bacterial killing rate. A single-stage surgery with a tantalum trabecular metal cage combining two different approaches is sufficient to maintain vertebral stability. This retrospective cohort study included 57 patients, 31 (54%) patients were treated with single-stage debridement and reconstruction with trabecular metal cages, and 26 (45.6%) patients received spine surgery without trabecular metal cages received surgery between January 2018 and March 2021 in our tertiary academic teaching hospital. The CRP values dropped borderline significantly in the TM cage group compared with the non-TM cage group postoperatively. In patients with spondylodiscitis, it is advisable to perform single-stage debridement and reconstruction with a trabecular metal cage, which allows abscess drainage and rapid mobilization, prevents deformity.

The nature abundant sodium metal is proposed as ideal anode materials for advanced batteries due to its high specific capacity of 1166mAh g-1 and low redox potential of -2.71V. However, the uncontrollable dendritic Na formation and low coulombic efficiency are still major obstacles for applications. Notably, the unstable and inhomogeneous solid electrolyte interphase (SEI) is recognized to be the root cause. As SEI layer plays a critical role in regulating uniform Na deposition and improving cycling stability, researches on SEI modification, especially the artificial SEI modifications has been extensively investigated recently. In this regard, we discussed the advances on artificial interface engineering from the aspects of inorganic, organic and hybrid inorganic/organic protective layers. Finally, we also highlighted the conclusions and key prospects for further investigations. We hope this review can provide a new insight for sodium metal protection.

Coagulant lectin from Moringa oleifera seeds (cMoL) was characterized by potentiometry and scanning electron microscopy (SEM) using MOF, Metal-Organic Frameworks of [Cu3(BTC)2.H2O)3]n, to immobilize cMoL and construct biosensors. Developed aluminum-air batteries degraded indigo carmine dye formulated similar to a textile effluent; biosensors investigated cMoL interaction with specific galactose and monitored residual dye. SEM revealed components of electrode assembly steps. Oxide reduction reactions of batteries generated Al(OH)3 promoting dye electrocoagulation. Cyclic voltammetry showed differentiated redox peaks related to dye residue quantification by cMoL. Electrochemical systems evaluated cMoL interaction with ligand and efficiently degraded dye; biosensors could be used for lectin characterization and monitoring dye residues in environmental textile effluents.

The need to regulate the non-exhaust particulate emissions from vehicles has been discussed worldwide due to the toxicity to the human body as well as the atmosphere. In-depth studies have been conducted on precise analysis of the non-exhaust particulates, in particular, accurate measurement of tire-brake-road wear particles, and their proportion in the atmosphere. In this study, the influence of tire and road wear particles (TRWP) on particulate matter (PM) in the atmosphere was investigated through tire and PM samples. PM samples were collected from the atmosphere using a high-volume sampler equipped with a quartz filter. Additionally, polycyclic aromatic hydrocarbons (PAHs) and heavy metals in tire rubber were analyzed as markers by pyrolysis-gas chromatography/mass spectrometry (GC/MS), GC/MS, and inductively coupled plasma/mass spectrometry (ICP/MS). More vinylcyclohexene was detected than dipentene in the markers measured in the samples of tires equipped with vehicles driving on the road with the high-volume sampler installed, while more dipentene was detected in total suspended particles (TSP) samples. Among the PAHs measured in tire samples, pyrene exhibited the highest concentration. In TSP samples, benzo(b)fluoranthene showed the highest concentration. Among the heavy metals, zinc exhibited the highest concentration in all tire samples and calcium in TSP samples.

Over the centuries, honey is known for its superior usage in culinary, and for its rich nutrition and therapeutic values which are scientifically proven in the medical field. The chemical composition of honey varies depending on its botanical sources and environment. Therefore, the nutrition content in honey is highly likely to be affected by contaminants, such as heavy metals and pesticides. To ensure the quality of honey, parameters such as the heavy metal content should be within the safe range of total standard mineral and trace elements as defined by the International Food Standard (Codex Alimentarius), and pesticides should not be present at all. The high concentration of heavy metal and pesticides not only deteriorates the quality and quantity of honey, but also causes harm to the bee colony itself. In the agriculture sector, the excessive usage of pesticides and fertilizer negatively impacts the overall honey production process. Bees, a pollinating agent, bring the polluted nectar back to their beehives, eventually contaminating the honey and depreciating its value. Hence, this article will comprehensively review the activities that contribute to heavy metal and pesticide contamination, the interactions of bees as a pollinating agent, the impact of the pollutant to the colonies, and subsequently to the honey production.

The Katangese Copperbelt area (KCA) located south-eastern of D.R. Congo presents high concentration of metal trace elements (MTE) in several soils due to a rich natural geochemical background, and intense mining activities, causing serious health issues to humans and animals. However, the lack of data on specific baseline concentrations makes it difficult to properly assess and monitor the environmental quality of soils in the region. In this study, the baseline concentration of 11 potentially toxic MTE (i.e., Mn, Zn, Cu, Co, Cr, Pb, Cd, Ti, Ni, Al, and Fe) was assessed in topsoils of the KCA, and the possible influence of land uses (croplands, forest and mining areas) was examined. Results showed the following baseline concentrations, i.e. lower and upper limits (mg.kg^-1) in cropland soils : Al (18.4–162.0), Cd (0.0–0.1), Co (0.1–3.5), Cu (0.8–17.7), Cr (0.0–0.2), Fe (4.7–233.8), Mn (3.5–575.6), Ni (0.1–1.9), Pb (0.2–2.4), Zn (0.1–20.3), Ti (0.0–392.6); in forests: Al (18.8–1167.1), Cd (0.02–0.48), Co (0.20–18.1), Cu (3.6–42.7), Cr (0.1–33.7), Fe (86.4–283.3), Mn (4.9–1538.9), Ni (0.05–24.2), Pb (0.3–13.7), Zn (2.0–7.0), Ti (0.2–0.8); and in mining areas: Al (7.4–241.2), Cd (0.01–164.8), Co (0.2–211.3), Cu (2.4–5485.4), Cr (0.03–0.4), Fe (5.9–481.6), Mn (7.1–95.9), Ni (0.1–1.9), Pb (0.2–390.8), Zn (1.5–5629.3), Ti (0.1–1.3). Cu and Zn were highest in mining areas demonstrating a prevalent influence of mining activities in altering the natural background of metals concentrations in the region. By contrast, croplands and forest shared a similar trend of Al and Mn contents, suggesting a mild influence of agricultural activity. Intriguingly, higher Cu and Co contents were found in forest compared to croplands. For all the three studied land uses, no straightforward relation was found between metal concentrations and soil total acidity. This study is the first attempt to establish reference values of MTE contents in the KCA soils and thus provides valuable information for legislative purposes and for soil quality assessment.

Metal toxicity in soils, along with water runoff, are increasing environmental problems that affect agriculture directly and, in turn, human health. In light of finding a suitable and urgent solution, research on plant treatments with specific compounds that can help mitigate these effects has increased, and thus the exogenous application of melatonin (MET) and its role in alleviating the negative effects of metal toxicity in plants, have become more important in the last few years. MET is an important plant-related response molecule involved in growth, development, and reproduction, and in the induction of different stress-related key factors in plants. It has been shown that MET plays a protective role against the toxic effects induced by different metals (Pb, Cd, Cu, Zn, B, Al, V, Ni, La, As, and Cr) by regulating both the enzymatic and non-enzymatic antioxidant plant defense systems. In addition, MET interacts with many other signaling molecules, such as reactive oxygen species (ROS) and nitric oxide (NO), and participates in a wide variety of physiological reactions. Furthermore, MET treatment enhances osmoregulation and photosynthetic efficiency and increases the concentration of other important antioxidants such as phenolic compounds, flavonoids, polyamines (PAs), and carotenoid compounds. Some recent studies have shown that MET appeared to be involved in the regulation of metal transport in plants, and lastly, various studies have confirmed that MET significantly upregulated stress tolerance-related genes. Despite all the knowledge acquired over the years, there is still more to know about how MET is involved in the metal toxicity tolerance of plants.

Pollution by heavy metals is one of the most severe environmental issues that threaten global sustainability. This review presents a recent advance in electrochemical sensors for heavy metal detection Rotating Disk Platinum Electrode are discussed. This study on the production of a modern natural water electrochemical antimony (II) and cupper (II) test include the use of platinum electrode. Antimony and cupper were pre-concentrated on the modified electrode surface and adsorbed to the surface, oxidizing at E = 540 mV and E = 85 mV, respectively. After 20 min of accumulation, time the best-defined anodic peak was obtained of surface. The precision was tested by carrying out chronoamperometric measurements at a concentration of Sb⁺² and Cu⁺² 8.5x10^-8 M and 9.5x10^-7 M, respectively.

MDA, as a sign of oxidative stress, was increasing as a factor that changes the toxicity of responses in the workplace and causes male infertility etiology. This study aims to measure the MDA levels of workers in the casting industry metal. This type of research was analytical explanatory research with a cross-sectional design. This study's variables include the variables taken are MDA levels while the independent variables were age, years of service, type of work, IMT, marital status, and smoking habits. A saturated sampling technique took the research sample of 34 workers. Data analysis used univariate and bivariate methods. The results determined that respondents had MDA hormone levels below the average of 24 or 70.6%, while respondents who had MDA levels above an average of 10 or 29.4%. MDA levels relating to the length of work and marital status, while the type of work, IMT, and smoking habits are not associated with MDA levels in metal casting industry workers in the CV. Bonjor Jaya Klaten.

We report the production of metal oxide (TiFe₂O₄, ZnFe₂O₄) nanoparticles by pulsed laser ablation technique in liquid environment. We used nano second Nd: YAG laser systems working at 532 nm and 1064 nm of wavelength, the energy of the laser beam was kept constant at 80 mJ. Absorbance spectra, surface plasmon resonance, optical band-gap and nanoparticle morphology were investigated using ultraviolet-visible (UV-Vis) spectroscopy, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). Changing the wavelength of the laser for growth, nanoparticles shown shift between the absorbance and surface plasmon resonance peaks in their UV-Vis spectra, this implies that the optical properties of the colloid nanoparticles depends on laser parameters, this was confirmed with the variation of the band gap energy. Furthermore, red shift for the absorbance peak was observed for samples as-growth at 532 nm around the 150 nm as function of time preparation. Whereas, for the samples as-growth at 1064 nm there is no shift in the absorbance spectra, this can be due to agglomeration and formation of larger particles. The characterization results shown appropriate plasmonic photo-catalysts properties of the particles, hence the photo activation of the nanoparticles was examined on antibacterial effect using colonies of Staphylococcus Aureus and Escherichia coli.

An array of Ag nanowires has been prepared from a facile, templated approach on Cu(BTC) (1,3,5-benzenetricarboxylic acid) metal organic framework (MOF) micropillars. The Ag-deposited scaffolding material may be used to prepare electronic or optoelectronic devices for various applications.

Transition-metal-free synthesis of 4-pyrones via TfOH-promoted nucleophilic addition/cyclization of diynones and water has been developed. This transformation is simple, atom economical and environmentally benign, providing rapid and efficient access to substituted 4-pyrones.

Nanomaterials based on metal oxides (MexOy) are employed as catalysts and/or sorbents in processes undergoing conditions in supercritical water (scH2O), the “green” reaction medium used to obtain energy relevant products. Their properties are greatly affected by the synthesis method used to produce the active MexOy. Moreover, in order to maintain their performance, it is more practical and cost-effective to use supported MexOy nanoparticles. Within this context, the present work deals with the preparation of carbon-supported ZnO and CuO composites by an innovative method based on impregnation under scH2O conditions. Metal oxides were impregnated on a carbon (C) support using a continuous flow tubular reactor. The results show that impregnation in scH2O is a promising approach for the preparation of ZnO/C and CuO/C composite materials. This one-step synthesis method, in a continuous flow, uses neither seed layer nor mineralizer, and it needs substantially lower preparation times than the conventional impregnation methods.

Heavy metal ions (HMIs) have acute toxic effects on the health and are dangerous for human ex-istence and the ecosystem. Therefore, its sensitive and selective detection is of great importance. In recent years various nanocomposite materials have been used by researchers for the detection of HMIs by using various modalities of electrochemical techniques. This review article summarizes the recent advances in developing electrochemical sensors based on numerous nanocomposite mate-rials for detecting heavy metal ions. Nanocomposites materials, such as Metal-Organic Framework (MOF), organic conducting polymers (OCP), carbon nanotubes, graphene/reduced graphene oxide, graphitic carbon nitride, metal oxide, chitosan, mxenes, metal nanoparticle-based nanocomposites, etc. have been explored by various researchers to improve the sensing properties of electrochemical sensors. This review emphasized the synthesis and characterization techniques of nanocomposite materials, modalities for HMI detection by electrochemical technique and the electrochemical sensors. Moreover, this review highlights the development of portable biosensors for detecting HMIs in real-world scenarios, such as environmental monitoring, food safety, and clinical diagnosis. This review also demonstrates the importance of electrochemical sensors-based on nanocomposite ma-terials as a reliable, sensitive, and selective tool for detecting HMIs.

AISI 1037 and AISI 304 steels are widely used across various industrial sectors, including manufacturing, transportation, petrochemical, and automotive industries. In this study, the effect of preheating on the toughness of dissimilar welded joints between AISI 1037 and AISI 304, joined by Shielded Metal Arc Welding (SMAW) using E309-16 electrodes, was investigated. The preheating process was performed prior to welding, and its influence on the joint's toughness was assessed through impact testing. Additionally, the hardness profile across the welded joint was evaluated using hardness testing. Macrostructure and microstructure examinations were conducted using an optical microscope and scanning electron microscopy (SEM) to analyse the fracture surfaces and microstructural evolution of the welded joints. The experimental results revealed that the impact strength increased as the preheating temperature was elevated. The highest hardness value, recorded in the fusion zone, reached 313 VHN. Compared to joints welded without preheating, the impact strength of the preheated welded joints significantly improved, with a notable transition in fracture mode from brittle to ductile behaviour. This indicates that the preheating process plays a critical role in enhancing the toughness and mechanical properties of dissimilar welded joints.

In a recent paper [B. Michon et al., Nat. Commun. (2023) 14:3033] optical conductivity experiments in cuprate superconductors were shown to display scaling properties consistent with the Marginal Fermi Liquid theory. Here we argue, that the temperature regime studied in these experiments does not allow to distinguish between Marginal Fermi Liquid and a Shrinking Fermi Liquid. In the latter scenario, which we recently proposed and which applies near a quantum critical point, dynamical fluctuations of the order parameter with short correlation length mediate a nearly isotropic scattering among the quasiparticles over the entire Fermi surface leading to strange-metal behavior. If the damping of these nearly local fluctuations increases by decreasing the temperature, the Fermi liquid regime shrinks and the strange-metal behavior is extended to the lowest temperatures. This Shrinking Fermi liquid scenario has many similarities and some differences with respect to the Marginal Fermi liquid theory. In particular, we show that the approximate scaling properties of the optical conductivity in some high-frequency regime predicted by the Shrinking Fermi liquid scenario account to a very good extend for the experimental data.

The SPEcies-At-Risk index for metals (SPEARmetal) was refined using updated physiological sensitivity data and validated to assess the ecological impact of metal contamination on benthic macroinvertebrate communities in the upper Nakdong River, near a Zn smelter in Korea. Biosurvey and chemical monitoring were collected at 18 sites surrounding the smelter and nearby mines. Acute ecotoxicity tests on 20 indigenous species from the Korean peninsula were conducted and used to update taxon-specific metal sensitivity data. The refined SPEARmetal index, based on this updated sensitivity, was significantly lower than previous versions, with most values below the severe impact threshold (0.5) in the mainstream. The correlation between hazard quotients in water and the SPEAR index improved, with the correlation coefficient increasing from 0.63 to 0.70. Despite consistently high benthic macroinvertebrate indices (BMI) across the study area, generic ecological indices such as total richness, EPT (Ephemeroptera, Plecoptera, Trichoptera), and Shannon diversity showed correlations with metal contamination levels. Principal component analysis identified SPEARmetal as the primary indicator associated with metal contamination in both water and sediment. These findings highlight the improved performance of the refined SPEARmetal index as a more sensitive and specific tool for assessing the ecological status of metal-impacted aquatic ecosystems compared to traditional indices.

Quantifying methane emissions is essential for meeting near-term climate goals and typically done using methane concentrations measured downwind of the source. One major source of methane that is important to observe and promptly remediate is fugitive emissions from oil and gas productions sites but installing methane sensors at the thousands of sites within a production basin is expensive. In recent years, relatively inexpensive metal oxide sensors have been used to measure methane concentrations at production sites. Current methods used to calibrate metal oxide sensors have been shown to have significant shortcomings resulting in limited confidence in methane concentrations generated by these sensors. To address this, we investigate using machine learning (ML) to generate a model that converts metal oxide sensor output to methane mixing ratios. To generate test data, two metal oxide sensors, TGS2600 and TGS2611, were collocated with a trace methane analyzer downwind of controlled methane releases. Over the duration of the measurements, the trace gas analyzer’s average methane mixing ratio was 2.40 ppm with a maximum of 147.6 ppm. The average calculated methane mixing ratios for the TGS2600 and TGS2611 using the ML algorithm were 2.42 ppm and 2.40 ppm with maximum values of 105.9 ppm and 106.3 ppm, respectively. A comparison of histograms generated using the analyzer and metal oxide sensors mixing ratios show overlap coefficients of 0.95 and 0.94 for the TGS2600 and TGS2611, respectively. Overall, our results showed there was a good agreement between the ML derived metal oxide sensors’ mixing ratios and those generated using the more accurate trace gas analyzer. This suggests that the response of lower-cost sensors calibrated using ML could be used to generate mixing ratios with precision and accuracy comparable to higher price trace methane analyzers. This would improve confidence in low-cost sensors’ response, reduce the cost of sensor deploying, and allow for timely and accurate tracking of methane emissions.

Wild-grown edible mushrooms are important in world diet, which are also efficient metal accumulators. Yunnan, southwest China is the main producing region with typically high geochemical metals. Environmental factors, bioaccumulation, distribution and human health risk of metals were examined in paired soil and Tricholoma matsutake (n=54). T. matsutake grows on acidified soils (pH=3.95–6.56) and metals showed strong heterogeneity with Fe, Mn, Zn and Cu ranged at 16–201, 0.046–8.58 g kg–1 and 22.6–215, 3.7–155 mg kg–1. High soil Fe content led to its great accumulation in T. matsutake (0.24–18.8 g kg–1). However, though soil Mn content was great higher than Zn and Cu, their concentrations in T. matsutake were comparable (21.1–487 vs. 38.7–329 and 24.9–217 mg kg–1). This suggested that T. matsutake prefers to accumulate Zn and Cu than Mn, and supported by bioaccumulation factor (BAF=0.32–17.1 vs. 0.006–1.69). Fe was mainly stored in stipe, while Mn, Zn and Cu were in cap, with translocation factor (TF) was 0.58 vs. 1.28–1.94. Therefore, stipe Fe showed the highest health risk index (HRI) at 1.28–26.9, followed by cap Cu (1.01–2.33), while 98–100% of Mn and Zn were risk-free. The higher concentration and greater risk of Fe was attributed to the significant effect of soil Fe content (R=0.34) and soil pH (R=–0.57). This study suggested that Fe as an essential mineral may exert toxic effects via T. matsutake consumption from geochemical high background areas.

Due to the optical properties of the Electron Transport Layer (ETL) and Hole Transport Layer (HTL), inverted perovskite solar cells can perform better than traditional perovskite solar cells. It is essential to compare both types to understand their efficiencies. In this article, we studied inverted perovskite solar cells with NiOx/CH3NH3Pb3/ETL (ETL = MoO3, TiO2, ZnO) structures. Our results showed that the optimal thickness of NiOx is 80 nm for all structures. The optimal perovskite thickness is 600 nm for solar cells with ZnO and MoO3, and 800 nm for those with TiO2. For the ETLs, the best thicknesses are 100 nm for ZnO, 80 nm for MoO3, and 60 nm for TiO2. We found that the efficiencies of inverted perovskite solar cells with ZnO, MoO3, and TiO2 as ETLs, and with optimal layer thicknesses, are 30.16%, 18.69%, and 35.21%, respectively. These efficiencies are 1.5%, 5.7%, and 1.5% higher than those of traditional perovskite solar cells. Our study highlights the potential of optimizing layer thicknesses in inverted perovskite solar cells to achieve higher efficiencies than traditional structures.

Honey is a very cost-efficient food source and a valuable export for the country of Uganda, but is commonly adulterated, resulting in consumers not being aware of the contents of their honey. As a result, it is important to be able to authenticate the honey that consumers are purchasing. This study evaluated the physicochemical properties (pH, free acidity, metal determination, moisture content, and FTIR spectra) of Ugandan and Manuka honey. Honey pH values ranged from 3.3 to 4.8 (±0.6) while free acidity values ranged from 34.87 to 62.22 (±8.69). The moisture content values of all honey samples were below 22%. The metal concentrations and functional groups present in Ugandan and Manuka honey were determined. Metal analysis by atomic absorption spectrometry detected five elements (Na, Ca, K, Cu, and Pb) in all honey samples in varying concentrations. The elemental concentrations were found in descending order as follows: sodium (Na) (9.38 ppm), calcium (Ca) (4.99 ppm), potassium (K) (2.48 ppm), copper (Cu) (1.87 ppm), lead (Pb) (0.28 ppm). FTIR analysis revealed similar patterns of spectral curve (O-H stretching and C-H stretching) across all honey samples analyzed, which is consistent with previously analyzed honey samples from other studies. Ugandan honey sample 7 collected in the Masaka Region was found to be most similar to the Manuka honey standard based on its observed physiochemical properties. All properties analyzed suggested Ugandan honey is of good quality and safe for consumption.

The characteristics of gap plasmon formed by nanoparticle-on-mirror (NPOM) structure composed of metal nanoparticles (MNP) and metal thin films have aroused the interest of various optoelectronic devices. The resonant spectrum obtained by the internal coupling effect of gap can be flexibly controlled by the polarization of incident light and the thickness of the dielectric layer between MNP and metal thin films. We have theoretically studied the resonance spectra of polarization-dependent gold ellipsoidal nanoparticles (GENP) and gold thin films in the gap region of NPOM structures. GENP and gold thin films are separated by a dielectric layer with a refractive index of 1.36. We observe that the intensity of the local electric field resonance peak in the gap region is inversely proportional to the polarization angle. Similarly, the intensity of the local electric field resonance peak in the gap region is inversely proportional to the thickness of the dielectric layer. We have obtained more than 2200 V/m local electric field intensity (dielectric layer thickness 0.3nm). Finally, the resonant peak wavelength of the electric field in the gap region of the NPOM structure is also controlled by the polarization angle of the incident light and the thickness of the dielectric layer.

Additive manufacturing processes offer various options to fabricate metal parts, which show numerous ecological and technological advantages compared to formative and subtractive manufacturing methods. Due to quick availability and high accuracy, they are particularly suitable to produce complex prototypes. Metal fused deposition modeling is a relatively new material extrusion additive manufacturing technique based on the widely used fused filament deposition process. This study focuses on the Inconel 625 metal filament from Markforged Inc., it consists of a mixture of metal powder and a binder system, the latter being removed during washing and sintering. In this article, the mechanical properties of printed and sintered Inconel were investigated using tensile testing specimens with three different infill patterns, solid, triangular, and gyroid, printed in flatwise and upright direction. In addition, investigations into the dimensional accuracy of the printed specimens and the sintering shrinkage were carried out. The results showed that neither the dimensional accuracy nor the sintering shrinkage was significantly influenced by the printing orientation. In the context of lightweight engineering, the structures proofed beneficial especially within the elastic region. Generally, triangular infill patterns resulted in higher stiffness, while gyroids led to more ductile specimens. A mass-related evaluation of tensile testing elucidates that with aid of the infill structures weight savings of 40 % resulted in mechanical performance decreased by only 20 % on average.

This research focusing on the environmental impact of tire and brake pad wear constitutes a significant area of transport-related studies. These two key vehicle components are not only the most frequently worn, but also generate micro and nano pollutants (i.e., rubber, metal oxides) that potentially harm the environment. Over half of the globally produced natural and synthetic rubbers, which amounted to about 30 million tons in 2022, are used for tire production. According to Wagner et al.'s research, over 1.3 million tons of such particles are released due to wear and tear in the European Union alone. This work focuses on examining snow deposits from various locations in an urban agglomeration (Poznan, Poland) in the winter season. FT-IR and NMR spectroscopic studies, optical and electron scanning microscopy SEM-EDS, and particle size studies using the DLS technique were conducted for a detailed characterization of pollutants in the environment. The conducted particle separation methods allowed for the extraction of a fraction mainly containing gum residues with particle sizes less than 2 µm. The results of these studies are crucial for understanding the impact of vehicle part exploitation on the environment.

Multilayered metallic sheets fabricated by hot metal forming processes are attractive structural components in the aerospace and automobile industry. The strength of the mechanical bond between the different layers is critical to the applicability of such components in load bearing applications. While it is well understood that the process conditions such as temperature, deformation and rate of deformation influence the bond strength, a clear functional relationship between these conditions and the bond strength has yet to be established. The objective of the current study is to investigate the joining of Aluminum-6061 alloy specimens by hot compression bonding. Hot compression tests of beam specimen pairs were conducted at different temperatures (300-500℃), with different strains and strain rates (10-2-10-1 [1sec]). Coupled thermo-mechanical finite element models were utilized to compute the time dependent thermo-mechanical fields that develop along the specimen interface. The computed values were used to map the spatial distribution of a scalar parameter J which is hypothesized to govern bond formation. Mechanical tensile tests were used to determine the bond strength and expose the bonded surfaces. It is demonstrated that the computed J distribution can be correlated well with SEM observations of the debonded surface. It is also shown that the actual bonded area can be predicted from the computations for a certain range of critical J values.

Laser powder bed fusion can fabricate porous structure through lattices, but it remains a challenge to prepare micropores (

Serine peptidase CLPP is conserved among bacteria, chloroplasts, and mitochondria. In humans and mice, its loss causes Perrault syndrome with growth deficit, infertility, deafness, and ataxia. In the filamentous fungus Podospora anserina, CLPP-loss leads to longevity. CLPP substrates are selected by CLPX, an AAA+ unfoldase. CLPX is known to target delta-amino-levulinic-acid synthase (ALAS) to promote pyridoxal-phosphate (PLP) binding. CLPX may influence cofactor association with other enzymes. Here, the evaluation of P. anserina metabolomics highlighted arginine/histidine reduction. In Mus musculus cerebellum, reductions of Arginine/Histidine and Citrulline occurred with concomitant accumulation of heme-precursor protoporphyrin-IX. This suggests that increased biosynthesis of 5-carbon (C5) chain deltaALA consumes not only C4 succinyl-CoA with C1 glycine but also specific C5 delta amino-acids. As responsible enzymes for these converse effects, elevated abundance of CLPX and ALAS is paralleled by elevation of OAT (PLP-dependent, ornithine-delta-aminotransferase). Possibly as consequence of altered C1 metabolism, CLPP-null cells in P. anserina proteome profiles showed strong accumulation of a methyltransferase and two mitoribosomal large subunit factors. Reduced Histidine levels may explain previously observed metal interaction problems. As main nitrogen-storing metabolite, deficient Arginine would affect the urea cycle and polyamine synthesis. Supplementation of Arginine and Histidine might rescue growth deficits of CLPP-mutant patients.

This study investigates novel ferrocene-based electrochemical sensors for metal cation detection through the design, synthesis and characterisation of ferrocene derivatives. Specifically, the re-search determines the redox potentials of ferrocene versus decamethylferrocene to provide in-sight into the redox potential variations between them. The investigation also examines how electrochemical oxidation of the ferrocene moiety can modulate host affinity for transition metals cations via effects such as electrostatic interactions and changes to coordination chemistry. Metal ion coordination to receptors containing functional groups like imine and quinoline is explored to elucidate selectivity mechanisms. These findings advance the fundamental understanding of ferrocene electrochemistry and host-guest interactions, supporting the development of improved cation sensors with optimised recognition properties, sensitivity, and selectivity. Overall, the work lays the necessary groundwork for applications in analytical chemistry and sensor technologies through customised ferrocene-derived materials.

Modern lifestyle has increased our utilization of pollutants such as heavy metals, aromatic compounds, and contaminants of emerging concern including pharmaceutical and personal products and other materials that may have an important environmental impact. Especially, the ultimate results of intense use of highly stable materials, such as heavy metals and chemical restudies are that they turn into waste materials which, when discharged, accumulate in the environment water bodies. In this context, the present review presents application of metal-organic frameworks (MOFs) in electrochemiluminescent (ECL) sensing for water pollutant detection. MOF composites applied as innovative luminophore or luminophore carriers, materials for electrode modification and enhancement of co-reaction in ECL sensors have enabled sensitive monitoring of some most common contaminants of emerging concern such as heavy metals, volatile organic compounds, pharmaceuticals, industrial chemicals and cyanotoxins. Moreover, we provide future trends and prospects associated with ECL MOF-composites for environmental sensing.

Laser heat treatment is applied after coating. Evaluation of the results was performed by studying the microstructures by metallographic, SEM/EDX microscopy and the mechanical properties were obtained by microscopic hardness and abrasion resistance. The objective of this study was to investigate the effect of laser heat treatment on the wear resistance of metal coatings. The results show the influence of the microstructure and chemical composition of the electrodes used on the micro-hardness and wear resistance of the metal coatings.

The cohesive energy of transition metal nanoparticles is crucial to understanding their stability and fundamental properties, which are essential for developing new technologies and applications in fields such as catalysis, electronics, energy storage, and biomedical engineering. In this study, we systematically investigate the size-dependent cohesive energies of all the 3d, 4d, and 5d transition-metal nanoparticles using first-principles density functional theory calculations. Our results show that the cohesive energies of nanoparticles decrease with decreasing size due to the increased surface-to-volume ratio and quantum confinement effects. We also find that the size-dependent cohesive energy trends are different for different transition metals, with some metals exhibiting stronger size effects than others. Our findings provide insights into the fundamental properties of transition-metal nanoparticles and have potential implications for their applications in various fields such as catalysis, electronics, and biomedical engineering.

Cancer has been considered one of the most serious diseases in recent decades. Early diagnosis of cancer is a crucial step for an expedited treatment. Ideally, detection of cancer biomarkers, which are usually elevated because of cancer, is the most straightforward approach to detect cancer. Consequently, the accurate, effective, and prompt detection of these compounds is an insistent need for the medical diagnosis of the disease in order to start an early therapy plan for the patients. Among these biomarkers, Carcinoembryonic antigen (CEA) is considered one of the most important tumor markers for colorectal cancer, but it has been also used as a biomarker for other types of cancers, including breast, gastric, ovarian, pancreatic, and lung cancers. Typically, conventional CEA testing depends on immunoassay approaches, which are known to be complex, highly expensive, and time-consuming. In this context, many biosensors were designed for the aim of detecting cancer biomarkers. The main prerequisites of these biosensors are high sensitivity, fast response, and low cost. Many nanostructures have been involved in the design of biosensors. Metal organic frameworks (MOFs) were found to be one of the most potential and promising materials for biosensing. MOFs are highly porous and crystalline materials that consist of metal clusters surrounded by organic linkers, where the assembly of these components gives rise to the exquisite geometric 3D structures of MOFs. Moreover, the unique structure and geometry of MOFs allow for a better tailoring of their design to provide properties that are needed by different categories of biosensors. In the past few years, researchers have extensively considered MOFs for their fabrication of biosensors that can be used for the early detection of cancer biomarkers. In this regard, MOFs were used solely or were further decorated with other nanostructures to introduce more accurate signals and lower limits of detection. This review briefly classifies and describes MOFs-based biosensors trials that have been published recently for the aim of detecting CEA.

Copper smelting has been the source of soil contamination in trace metals in Penga Penga (Lubumbashi). Residents are exposed to trace metal ingestion and planting trees is challenging in such soil conditions. Nevertheless, planting trees in former household dumps or using various types of amendments allowed the provisioning of fruits in few residences. In the perspective of scaling up the process, a survey has been conducted with the aim of assessing the effectiveness of the planting processes on the trace metal content in fruits and leaves of Mangifera indica L. and Syzygium guineense (Willd) DC. Samples were collected in residential households from Penga Penga and Kalebuka (a non-polluted suburb). The bioconcentration factor (BCF) and the safe weekly consumption (SWC) were calculated for each species. Results showed higher values of total and soluble concentrations of Cu, Pb, and Zn in the rhizosphere of the two species at Penga Penga. Metal concentrations were higher in fruits and leaves from Penga Penga with 47% of samples above FAO and WHO thresholds (vs 18.5% in Kalebuka). The BCF values were below 1 demonstrating the effectiveness of the process to reduce metal translocation to leaves and fruits. Recommendations from the SWC limited by Pb for consumption to 9 kg for mango flesh and by Cd 6.6 kg for S. guineense fruits at Penga Penga (Vs 78 and 68 kg at Kalebuka). Finally, results from this study provide interesting lessons from the scaling up and the technical itinerary of planting tree un Penga Penga.

The present review article concludes with three different types of materials recently used to enhance the efficiency of supercapacitors. The first type involves carbon-based materials for storage and supercapacitor applications. The carbon materials could be obtained naturally and synthesized manually based on the needs. The second type discusses the recent advances in metal oxide materials for high-performance supercapacitors. The metal oxide materials involve in different types of attachment through the bi-tri metallic bonding, which enhances the specific capacitance. The third type involves recently advanced materials for high energy and power density application. The power and energy density of the materials is enhanced by the surface modification of the materials. In recent days, the MXene and Nano-composite materials seems to be an appropriate material to increase the power and energy density of the device.

Organophosphorus nerve agents are amongst the most toxic chemicals known to human beings. 9 They interfere with the central nervous system, resulting in continuous muscle contractions, 10 paralysis and even death. Prohibition by many countries around the world cannot disguise the 11 remaining presence of nerve agents in stockpile storage and governmental deployment, 12 highlighting the dire need for an efficient catalyst to degrade and detoxify nerve agents by 13 hydrolysis. Metal-organic frameworks (MOFs) have raised a few eyebrows for their permanent 14 porosity, precise tunability, and lasting stability. Modern Reticular Chemistry fosters the design and 15 synthesis of well-defined crystalline MOFs with open Lewis acidic metal sites that can catalytically 16 hydrolyze nerve agents both in aqueous solution and in solid state systems, unveiling unparalleled 17 potential for MOF-based personal protection gears. In this review, a summary of the representative 18 catalytically active MOFs in nerve agent hydrolysis is discussed. MOFs are categorized by their 19 reticular structure, emphasizing the capability and mechanistic insights of each single MOF in nerve 20 agent hydrolysis. The author’s perspective on the current challenges and future directions of MOF- 21 based catalysts in real-world protection applications is also provided, which hopefully could shed some 22 light on the future development of commercially available MOF protection suits.

This study provides a novel method to prepare metal-ceramic composites from magnetically selected iron ore using microwave heating. By introducing three different microwave susceptors (Activated Carbon, SiC, and a mixture of Activated Carbon and SiC) during the microwave process, effective control of the ratio of metallic and ceramic phases has been achieved easily. The effects of the three susceptors on the microstructure of the metal-ceramics and the related reaction mechanisms were also investigated in detail. The results show that the metal phase (Fe) and ceramic phase (Fe2SiO4, FeAl2O4) can be maintained, but the metal phase to ceramic phase changed significantly. In particular, the microstructures appeared as well-distributed nanosheet structures with diameters of ~400 nm and thicknesses of ~20 nm when SiC was used as the microwave susceptor.

The electromagnetic inference is an issue from decades, where working for a better shielding material is still on-going. The purpose of this study is to review the existing methods in the formation of graphene, metal and polymer-based composites. Study indicates that in graphene and metal-based composites, the utilization of alternating deposition method showed the highest shielding effectiveness, whereas, in polymer-based composite, the utilization of chemical vapor deposition method showed highest shielding effectiveness. However, this review reveals that still there is a gap in the literature in terms of the selection of the method. Although there are various available methods which researchers adopt as per their convenience, none of the studies makes a comparison of the methods to form a similar composite. Therefore, as a future gap researcher needs to adopt various methods to form a single composite and then make a comparison of shielding effectiveness. This act will be useful for future researchers to select the appropriate method.

This mini-review critically summarizes the knowledge of imprinted polymer-based electrochemical sensors, for the detection of pesticides, metal ions and waterborne pathogenic bacteria, focusing on the period the last 5 years (citation of 78 papers published in 2017-2021, ie 63% of total citations). MIP-based electrochemical sensors exhibit low limit of detection, high selectivity, high sensitivity and low cost. Herein, we focused on the timely topics of water pollution by organics, inorganics and micro-organisms represented by pesticides, metal ions and bacteria, respectively. We put the emphasis on the design of imprinted polymers and their composites and coatings by radical polymerization, oxidative polymerization of conjugated monomers or sol-gel chemistry. Whilst most imprinted polymers are used in conjunction with differential pulse or square wave voltammetry for sensing organics and metal ions, electrochemical impedance spectroscopy (EIS) appears as the chief technique for detecting bacteria. This successful combination of EIS and imprinting technology should be harnessed in the coming years in the case of bacteria. Interestingly, bacteria are not always probed by bacteria-imprinted polymers; we report here their detection by monitoring specific (macro)molecules that reflect bacterial activity, for example quorum sensing signaling molecules or flagella proteins. If much has been developed in the past decade with glassy carbon or gold electrodes, it is clear that carbon paste electrodes of imprinted polymers are more and more investigated due to their versatility. Shortlisted case studies were critically reviewed and discussed; clearly a plethora of tricky strategies of designing selective electrochemical sensors are offered to “Imprinters”. We anticipate this review will be of interest to experts and new comers in the field who are paying time and effort combining electrochemical sensors with MIP technology.

Metal organic frameworks (MOFs) composed of metal ions and multifunctional organic ligands are one of the most attractive porous materials. Their potential applications in gas storage, separation, catalysis, biomedicine and many other fields have attracted much attention. In this study, Nano-Mn-MOF-74 with nano size were successfully synthesized by adding acetic acid and characterized it by SEM, TEM and XRD. Furthermore, a new method to trace the degradation process of nanoMOFs through detection of ligand concentration under physiological conditions was developed.

The Mediterranean Sea is one of the most impacted basin in terms of microplastics pollution. Land-based activities are the major sources of plastic litter to the ocean, with harbors probably representing significant hotspots. In the framework of the SPlasH! project (Stop alle Plastiche in H2O, Interreg Marittimo project), microplastics were sampled in three north-western Mediterranean harbors during summer and winter. In this study, the areal concentrations of microplastics ranged from 5,576 to 379,965 items.km-2. A decreasing gradient was observed from the inner to the outer zones of the studied harbors, pointing out these enclosed systems as hotspots regarding microplastic pollution. During the summer, because of an enhancement of port activities, the areal concentrations of microplastics were higher than in winter. The investigation microplastics size classes distribution in the surface waters revealed that microplastic within a size range between 300 µm and 500 µm were depleted. During this study, we assessed trace metal partitioning (Pb, Fe, Cu, V, Cd and As) between the dissolved phase and biofilm, thus highlighting concentrations within the biofilm two and six orders higher than those in the dissolved phase. This result strongly suggest trace metal bioaccumulation within the biofilm. When trace metal concentrations are normalized over the corresponding surface of microplastics and microplastics, higher values were obtained for microplastics evidencing their enhanced capacities to bioaccumulate contaminants with respect to macroplastics.