Citrus waste has been used as a source of bioplastic research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. For many years, researchers have been investigating an environmentally friendly way to take citrus and other organic waste and turn it into polymers that may be used, for instance, to produce bio-based and biodegradable films for food packaging. The goal of this study is to create biofilms from orange (OW) and ginger waste (GW) using an ultrafine grinder and study the films' properties. Since pectin has the ability to gel and because cellulosic fibres are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste were shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension's viscosity increased from 29 to 57 mPa.s for OW and from 217 to 376 mPa.s for GW while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150°C, and maximum degradation occurs after 300°C.

Thermoelectric (TE) waste heat recovery has attracted significant attention over the past decades, owing to its direct heat-to-electricity conversion capability and reliable operation. However, methods of system-level TE design optimization for specific application systems have not been thoroughly investigated. This work theoretically studies the performance optimization and exergy analysis of TE systems for recovering waste heat from the exhaust ducts of a gas turbine power plant. A numerical tool has been developed to solve the coupled charge and heat current equations with temperature-dependent material properties and convective heat transfer at the interfaces. Our calculations show that at the optimum design with 50 % fill factor and 6-mm leg thickness made of state-of-the-art Bi2Te3 alloys, the proposed system can reach power output of 10.5 kW for the TE system attached on a 2 m-long, 0.5 x 0.5 m2-area exhaust duct with system efficiency of 5 % and material cost per power of 0.23 $/W. Moreover, our extensive exergy analysis reveals that only 1 % of the exergy content of the exhaust gas is exploited in this heat recovery process and the exergy efficiency of the TE system can reach 8 % with improvement potential of 85 %.

In response to the growing need for efficient energy conversion technologies, this pa-per introduces an innovative Tubular Thermoelectric Generator (TTEG), specifically de-signed for high-efficiency conversion of waste heat into electrical energy. Unlike conven-tional flat plate thermoelectric generators (FTEGs), the TTEG incorporates full-ring ther-moelectric elements within a tubular layout, offering a novel approach to thermal energy recovery from fluid-based systems. This design significantly enhances the heat transfer capabilities, thereby improving the efficiency of energy conversion. Comprehensive simulations and analyses form the core of this study, where the per-formance of the TTEG is rigorously compared with traditional FTEGs. These comparisons highlight the advantages of the tubular design in terms of energy conversion efficiency and practical applicability in various scenarios. The findings reveal that the TTEG not only outperforms its flat plate counterparts but also presents a scalable and adaptable so-lution for waste heat recovery in a wide range of industrial and automotive applications. This research contributes to the field of energy science and technology by presenting a detailed experimental setup, complete with reproducible procedures and results. It opens new pathways for the development of more sustainable and efficient energy conversion systems, aligning with the goal of harnessing renewable and sustainable energy sources. The potential applications of this technology in enhancing energy efficiency and reducing environmental impact are vast, making it a significant step forward in the quest for clean and sustainable energy solutions.

One way to increase overall natural gas engine efficiency is to transform exhaust waste heat into useful energy by means of a bottoming cycle. Organic Rankine cycle (ORC) is a promising technology to convert medium and low grade waste heat into mechanical power and electricity. This paper presents an energy and exergy analysis of three ORC-Waste heat recovery configurations by using an intermediate thermal oil circuit: Simple ORC (SORC), ORC with Recuperator (RORC) and ORC with Double Pressure (DORC), and Cyclohexane, Toluene and Acetone have been proposed as working fluids. An energy and exergy thermodynamic model is proposed to evaluate each configuration performance, while available exhaust thermal energy variation under different engine loads was determined through an experimentally validated mathematical model. Additionally, the effect of evaportating pressure on net power output , absolute thermal efficiency increase, absolute specific fuel consumption decrease, overall energy conversion efficiency, and component exergy destruction is also investigated. Results evidence an improvement in operational performance for heat recovery through RORC with Toluene at an evaporation pressure of 3.4 MPa, achieving 146.25 kW of net power output, 11.58% of overall conversion efficiency, 28.4% of ORC thermal efficiency, and an specific fuel consumption reduction of 7.67% at a 1482 rpm engine speed, a 120.2 L/min natural gas Flow, 1.784 lambda, and 1758.77 kW mechanical engine power.

The fishmeal production industry is essential for providing protein for animal feed in the aquaculture sector. However, the industry faces challenges related to energy consumption and environmental sustainability. This study evaluates the energy efficiency and environmental benefits of waste heat recovery (WHR) technologies in a fishmeal production plant in Vietnam. Data were collected from the plant between 2016 and 2022, and a specific energy consumption (SEC) indicator and a comprehensive methodology were utilized. Implementing an economizer as a WHR technology resulted in a 55.5% decrease in SEC compared to the state before installation. The enhanced energy efficiency also translated to reduced energy consumption per output unit. Moreover, the economizer contributed to annual energy savings of 4,537.57 GJ/year and cost savings of $26,474.49. Additionally, carbon dioxide (CO2) emissions associated with producing one ton of fishmeal decreased by 58.37%. These findings highlight the potential for WHR technologies to improve energy efficiency and reduce the environmental footprint of fishmeal production. The study's results provide valuable insights for practitioners and policymakers in promoting energy efficiency practices and reducing environmental impact in the industry.

Mining is one of the main economic activities of several developing countries as Chile. Due to the progressive fall of the ore grades and the increasingly refractory composition of minerals, concentrating plants have increased that has led to an increase in the generation of tailings. Tailings, especially those obtained in the past, have remaining copper and other valuable species in quantities that can potentially be recovered, such as gold, silver, vanadium and rare earth elements. This transforms this abundant waste into a potential source of precious or strategic metals for secondary mining. One of the techniques of solid-liquid separation that allows the processing of solutions with low concentrations of metals corresponds to the adsorption, and more recently the biosorption, which is based on the use of biological matrices that do not constitute an environmental liability after application. Biosorption occurs as a consequence of the wide variety of active functional groups present in the different types of biomass. Bacterial, fungal, plant and algal biomasses have been described as biosorbents, mainly for the treatment of diluted and simple solutions. This work aims to recover copper from leached tailings using biomass of the red algae Gracilaria chilensis as a biosorbent. The tailing samples were taken from an abandoned deposit in the north of Chile and after an acid leaching copper was biosorbed, for which the kinetics of adsorption and the equilibrium isotherms were studied, applying the Freundlich and Langmuir models. Operational parameters such as adsorbent dose, pH and initial metal concentration were studied.

Waste recovery is an important aspect towards human and environmental health protection. Unfortunately, proper food waste management is among the serious challenges in the field of solid waste management worldwide. Therefore, it is of great importance to conduct studies towards achieving efficient and cost-effective approaches for food waste management. This study investigated the potential of recovering food waste through maggots’ production as animal feed. The influence of fly attractant application on maggot production was also investigated. The study also investigated the potential of maggot production for waste recovery and reduction. Four different types of food waste (starch food leftovers, rotten bananas and peels, rotten pineapple and peels, and rotten oranges) were used in the investigation process. From the results, it was observed that the application of fly attractants had a significant effect on the production of maggots as determined by the weights after harvesting. Average weight of 94 g/kg of maggot was achieved from banana materials with an application of fly attractant during the 8th day of the cultivation; which is equivalent to a 32.4% increase from the same day when the material was cultured without applying fly attractant. Also, from the starch materials, about 77 g/kg of maggot weight was achieved; which is a 54.6% increase from the same day and the same material but without application of fly attractant. Moreover, the relative dry weight reduction in the trials varied from 52.5% to 82.4%.

The increasing volume of Municipal Solid Waste (MSW), including biodegradable plant residues such as pruning, leaves, and kitchen waste, presents a substantial environmental challenge due to the limited availability of landfill space and the resulting environmental contamination. Sustainable waste management practices, encompassing recycling and waste-to-energy conversion through biological or thermochemical processes, are imperative. In the Municipality of Athens, Greece, significant quantities of green waste generated from public and private gardening activities provide a valuable opportunity for energy recovery and landfill waste reduction. In accordance with Directive 2008/98/EC, Athens emphasizes waste prevention, reuse, recycling, and recovery. This study examines alternative bio-waste and green waste management systems, with examples from Europe, focusing on the Athens Directorate of Urban Green Spaces and Urban Wildlife. It discusses methods for assessing the energy value of pruning residues, providing a definitive disposal framework. Additionally, it presents a technoeconomic study of one of the Municipal Swimming Pools in the Municipality of Athens, investigating the production and distribution of thermal energy to meet the heating needs of the pool facilities. This research identifies key constraints and their impact on decision-making, highlighting the potential for alternative green waste management. It advocates modern recycling techniques in line with national and Community legislation, demonstrating significant environmental and economic benefits.

Currently, with the rapid growth of the population, the demand for metals has increased, especially for the manufacture of electronic devices such as cell phones, computer equipment, among others. Once these devices stop working, most are sent to landfills, which represents a danger since these wastes contain metals and other materials that must be properly managed to prevent them from having a negative effect on the environment and the human being. On the other hand, e-waste contains valuable metals such as copper, gold, and silver, the concentration of which in these materials makes it cost-effective to recover. This paper presents a review of the extraction and recovery of valuable metals from electronic waste by hydrometallurgical methods, as well as patents and industrial processes related to the management and treatment of this waste.

In this study, a decentralized incineration facility was evaluated over a three-year period, focusing on performance aspects such as burning rate, ash production, fuel and electricity consumption, and ash composition while processing animal by-products (ABP). The total cost for ABP incineration was determined to be 159 € per ton of ABP, with the major components being capital depreciation (42%), maintenance expenditures (26%), labor (18%), and transportation costs (9%). Liquified petroleum gas (LPG) consumption ranged from 3-7 kg per ton of ABP, while electricity use was between 15-20 kWh per ton of ABP incinerated. The incineration process generated 7-10% (by weight) ABP ash, which was characterized by high calcium and phosphorus content and low levels of hazardous trace elements. Leaching tests demonstrated the potential for recovering the alkaline supernatant for flue gas treatment and the phosphorus-rich slurry for fertilizer production. The findings suggest that energy recovery and valorization are crucial for minimizing operational costs and environmental impact, emphasizing the benefits of integrating advanced resource recovery techniques in ABP incineration facilities.

This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

Plastic waste constitutes one of the most important sources of pollution worldwide. Despite the growing recycling trend, nowadays there are no effective technologies that can compensate for the continuous increase in plastic production. Polyesters and polyamides are one of the most produced single-use plastics, mainly used in manufacturing textiles and soft drinks bottles. Today, only a very low fraction of these polymers can be recycled. It can be done by exploiting two leading technologies: mechanical and chemical recycling. Mechanical recycling represents, nowadays, the most used industrial application. However, it can treat a very narrow range of waste materials due to the impossibility of removing dyes and the deterioration of mechanical properties due to the incompatibility of different plastic materials. Another critical limit of this recycling technology is the limited number of recycling loops that can be done due to the thermal degradation that occurs during the extrusion process. The second possibility is chemical recycling, which allows the depolymerization of the original product to recover the monomers directly. The main drawbacks are the long reaction times and the many solvents needed to achieve high-purity products. Therefore, chemical recycling is economically feasible, only for big companies that can produce the virgin polymer in situ. In this work, a new technology has been patented. This process is constituted of three main steps. The first one is the distillation-assisted cyclodepolymerization (DA-CDP), introduced as a modification of the CDP process. In this unit, cyclic oligomers together with high molecular weight compounds have been produced. Then, after polymer purification, it is possible to achieve the same molecular weight of the initial polymer in less than 30 minutes, exploiting the ring-opening polymerization (ROP) in the next step.

Preparation of a low-cost cellulose-based bioadsorbent from the cellulosic material extracted from the rose stems (CRS) was carried out; rose stems were considered agricultural wastes. After the required pretreatment of this waste, and its further treatment with an acidic mixture of acetic and nitric acids, the CRS product was yielded. The resulting bioadsorbent was characterized by several techniques, such as X-ray diffraction, which revealed diffraction maxima related to cellulose structure, whose calculated crystallinity index (CrI) was 75 %. In addition, Fourier Transform Infrared spectroscopy (FTIR), 13C Nuclear Magnetic Resonance (NMR), and X-ray Photoelectron Spectroscopy (XPS) showed signs of acetylation of the sample, also, the thermal properties of the solid was evaluated through Thermogravimetric Analysis (TGA). Scanning Electron Microscopy (SEM) showed cellulose fibers before and after the adsorption process, some particles with not regular shapes were also observed. The CRS bioadsorbent was used in the effective adsorption of valuable Tb(III) from aqueous solution. The adsorption data resulted in a better fit to the Freundlich isotherm, and pseudo-second-order kinetic models; however, chemisorption had not been ruled out. Finally, desorption experiments revealed a recovery of terbium ions with an efficiency of 97 % from terbium-loaded bioadsorbent.

The easiest way to utilise leather waste shavings is normally to produce new fuels from the most contaminated fractions for combustion or gasification. But since these waste contain up to 10% of nitrogen (N), burning it only for the energy recovery would not be rational. On the other hand, the chromium (Cr) content exceeding 5% in half of the waste stream (w/w) is too significant to be applied in agriculture. In this work, 4 acid hydrolysates from leather waste shavings both wet-white free of Cr and wet-blue with Cr were used: 2 with a mixture of acids and supplemented with Cu, Mn, Zn and other 2 as semi-product from collagen extraction using hydrochloric acid. The acid hydrolysates were prepared using a specific combination of acids under controlled conditions, ensuring the maximum release of nitrogen while maintaining the safety and integrity of the process. Additionally wet-green leather waste shavings eg. impregnated with olive extract were used followed by their 2 treatments: amendment with a biochar from “wet white” leather waste shavings and amendment with this biochar incubated with a commercial phosphorus stimulating microbial consortia BactoFos. They were applied as organic nitrogen-based fertilisers in a glasshouse experiment, consisting of 4-5 subsequent harvests every 30 days, under spring-autumn conditions in northern Poland. Ryegrass dry matter and nitrogen plant content were measured across 7 increasing fertiliser doses. Nitrogen utilisation, relative agronomic effectiveness, nitrogen use efficiency, total ryegrass dry matter and nitrogen utilisation breakdown across harvests were calculated. Biochar amended wet-greens provided the highest nitrogen use efficiencies exceeding 100% after 4 months growth (for 20 kg N/ha) and varying from 17% to 37% in particular months. This is backed up by another parameter (relative agronomic effectiveness) that for these materials exceeded 150% for single month and in total around 33%. Biochar amendments significantly increased agronomic parameters for wet-greens and their microbial treatment enhanced them even further. In sustainability aspects, assuming only the industrial partner waste potential, that gives 919,8 t of recycled nitrogen per year, which comes back to the environment in plant biomass. Recycling this type of waste can replace inorganic fertilizers reducing greenhouse gas emissions and carbon footprint.

Printed circuit boards (PCBs) make up 3 to 5% of all electronic waste. The metal content of spent PCBs can reach 40%. They usually contain valuable metals - Ag, Au, Pd, as well as other metals such as Cu, Sn, Pb, Cd, Cr, Zn, Ni and Mn. However metallic part of whole PCB is 40-60% including Cu layers between the fiberglass-polymer layers. The paper describes economics of the the valuable metals (Ag, Au, Pd) containing concentrate preparation from raw PCB. Considered the influence of pre-treatment method of PCB before the extraction of valuable metals on the extraction self-cost change. The disintegration method is based on the high-energy impact of the particles of the material to be ground, thus causing the separation of the metallic components of the PCB. In the course of the work, single and double direct grinding by the method of disintegration was studied. For the calculation the test batch 10’000 kg of two types of PCB were taken for estimation of the self costs and potential profit in case of complete valuable metals (Ag, Au, Pd) plus Cu extraction. Is shown that from 10’000 kg of studied PCB is possible to obtain 1144 and 1644 kg of metal-rich concentrate, which further should be subjected to electro-hydrochlorination for metals leaching. The main findings shows, that despite of high content of Cu in studied PCB, the commercial value is insignificant in total income from the Ag, Au and Pd sale. Was established correlation of the self-cost decrease after separative disintegration of PCB by metal content increase (by specific metals such as Au, Ag, Pd and also Cu) with the metal potential yield after extraction.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

The feasibility of using zeolites, synthesized from components found in municipal solid waste fly ash (MSW-FA), as sorbents for the recovery of nutrients (nitrate and phosphate) and heavy metals is critically assessed in this review. The inherent drawbacks of utilising a highly contaminated, variable, and relatively Al- and Si-dilute source such as MSW-FA to synthesize zeolites are discussed, and different methods to extract and decontaminate zeolite precursor materials from MSW-FA are considered. Ways to synthesize tailored zeolites and how their properties as well as the operational conditions impact the adsorption of cations such as ammonium and heavy metals are summarized. The use of surface-modified zeolites to adsorb nitrate and phosphate is also reviewed. And subsequently, approaches to utilise directly or recover for reuse the adsorbed compounds are considered, discussing potential challenges and mitigating measures related to leaching of unwanted compounds from the zeolites. Moreover, the possibility to regenerate the adsorption capacity of the zeolites for multiple adsorption cycles is considered. In the final chapter of the review a more general discussion of the main challenges and existing research gaps is provided, giving directions for recommended studies.

In this paper, an improved system to efficiently utilize the low-temperature waste heat (WHUS) from the flue gas of coal-fired power plants is proposed based on heat cascade. The essence of the proposed system is that the waste heat of exhausted flue gas is not only used to preheat air for assisting coal combustion as usual but also to heat up feedwater and the low-pressure steam extraction. Preheated by both the exhaust flue gas in the boiler island and the low-pressure steam extraction in the turbine island, thereby part of the flue gas heat in the air preheater can be saved and introduced to heat the feedwater and the high-temperature condensed water. Consequently, part of the high-pressure steam is saved for further expansion in the steam turbine, which obtains additional net power output. Based on the design data of a typical 1000 MW ultra-supercritical coal-fired power plant in China, in-depth analysis of the energy-saving characteristics of the optimized WHUS and the conventional WHUS is conducted. When the optimized WHUS is adopted in a typical 1000 MW unit, net power output increases by 19.51 MW, exergy efficiency improves to 45.46%, and net annual revenue reaches 4.741 million USD. In terms of the conventional WHUS, these aforementioned performance parameters are only 5.83 MW, 44.80% and 1.244 million USD, respectively. The research of this paper can provide a feasible energy-saving option for coal-fired power plants.

Data centres, though a necessary part of modern society, are being stigmatised for consuming vast amounts of electricity for their operational and cooling needs. Due to Ireland’s reliance on fossil fuels to meet the increased energy demand of data centres, the data centres are contributing significantly to Ireland’s total carbon emissions. As much of this energy is expelled from data centres as waste heat energy, the potential for recycling some of this wasted heat energy was explored using environmentally friendly systems from recent publications. The recovered waste heat energy was applied in a vertical farming system, and the benefits of this waste heat to the vertical farm were analysed and quantified in two scenarios. Using conservative estimates, it was predicted that each vertical farm could be between 5-23% the size of the data centre and produce enough food to feed between 14-61 adults their daily calorie needs, and between 13-58 people their daily fresh produce requirements, depending on the scenario applied. For a more accurate prediction, each vertical farm would have to be assessed on a case-by-case basis. However, there was not enough data available on Irish data centres to perform these calculations.

The production of photovoltaic modules is increasing to reduce greenhouse gas emissions. However, this results in a significant amount of waste at the end of their lifespan. Therefore, recycling these solar panels is important for environmental and economic reasons. However, collecting and separating Crystalline silicon, Cadmium Telluride, and Copper indium gallium selenide panels can be challenging, especially in underdeveloped countries. The innovation of this work is to develop a process to recycle all solar panel waste. The dissolution of all metals is studied through the leaching process as the main step of the flowchart. In the first step of leaching, silver can be recovered 98% by 0.5 nitric acid. Then, the second and third step involves the use of glycine for base metals dissolution, followed by the leaching of valuable metals with hydrochloric acid. The effect of parameters such as initial pH, acid concentration, solid/liquid ratio, and Hydrogen peroxide concentration are studied. The results show that Cu, Pb, Sn, Zn, Cd, In, Ga, and Se can be recovered until about 100% under optimal conditions. The optimal conditions for the dissolution of Cu, Zn, and Cd were the glycine concentration of 0.5 M, Temperature of 25 ˚C, the solid/liquid ratio of 10 gr/l, and 1% of Hydrogen peroxide. The optimized glycine concentration for the leaching of lead and tin was 1.5M. Indium and gallium were recovered to 100% by the use of 5M Hydrochloric acid, S/L=10gr/l, and T=45 ˚C. Separation of selenium and tellurium occurred by 0.5 M HCl at a temperature of 60 ˚C. Additionally, for the first time, a general outlook for the recycling of various end-of-life solar panels is suggested.

The rapid growth of the global population is causing a significant increase in waste production, leading to serious environmental and public health challenges. To address these issues, waste management systems are incorporating advanced technologies. Machine learning and computer vision are used to predict waste patterns, optimize collection schedules, and improve sorting accuracy. Deep learning automates the sorting process, provides predictive analytics, and enhances recycling rates. Robotics, combined with AI and computer vision, improves sorting efficiency, while the Internet of Things (IoT) monitors waste levels and optimizes collection routes. Despite these benefits, challenges such as data scarcity, high computational demands, and the need for substantial infrastructure investments must be addressed. This research explores the integration of advanced technologies into waste management and evaluates their effectiveness using waste datasets. It highlights the potential to tackle environmental challenges and lay the groundwork for more intelligent waste management solutions.

Waste management is a critical issue globally, and Bangladesh is no exception, facing significant challenges due to rapid urbanization, population growth, and inadequate infrastructure. This article explores comprehensive waste management strategies, including waste segregation, recycling, composting, and waste-to-energy technologies, emphasizing their environmental and health benefits. It examines the past and present waste management conditions in Bangladesh, highlighting the progress made and the persistent challenges. The article also compares waste management practices in neighboring countries like India, Bhutan, Sri Lanka, and Nepal, offering insights into potential improvements for Bangladesh. Emphasizing the need for public awareness, community involvement, and modern infrastructure, it calls for collaborative efforts to achieve sustainable waste management and environmental preservation in Bangladesh. This article examines the critical issue of waste management, emphasizing its importance in mitigating environmental pollution, conserving resources, and protecting public health. It provides a detailed analysis of various waste management strategies, including waste segregation, recycling, composting, and waste-to-energy technologies, highlighting their benefits and implementation challenges. Focusing on Bangladesh, the article traces the evolution of the country's waste management system, from past inadequacies to recent improvements, while acknowledging persistent issues such as rapid urbanization and insufficient infrastructure. Comparisons with waste management practices in neighboring countries like India, Bhutan, Sri Lanka, and Nepal offer valuable insights and potential strategies for Bangladesh to adopt. The article underscores the necessity of public awareness, community involvement, and robust infrastructure to achieve effective waste management. It calls for a collaborative approach involving government, private sector, NGOs, and local communities to develop sustainable solutions. By investing in modern waste management technologies and fostering responsible consumption and disposal habits, Bangladesh can address its waste management challenges, ensuring environmental preservation, public health, and overall national well-being.

The escalating global population and subsequent demand for agricultural products have led to a surge in agricultural waste generation, posing significant disposal challenges. Conventional disposal methods such as burning and dumping not only harm the environment but also jeopardize human health and safety. Recognizing the urgent need for sustainable waste management, researchers have increasingly focused on repurposing agricultural plant waste as a valuable resource. This paper presents a comprehensive review of the potential of agricultural plant waste in wealth creation and sustainable development. It highlights the detrimental impacts of current disposal methods and emphasizes the necessity for alternative approaches. By analyzing the physical, mechanical, and chemical properties of plant fibers, particularly cellulose, hemicellulose, and lignin, this review underscores their suitability for diverse applications. Moreover, it explores the emerging trend of utilizing pineapple leaf fiber, a sustainable and lightweight material, in structural applications such as UAV construction. With its exceptional mechanical properties and biodegradability, pineapple leaf fiber holds promise as a viable alternative to traditional materials, contributing to a more sustainable future. In conclusion, this review advocates for a paradigm shift towards embracing agricultural plant waste as a valuable asset for economic prosperity and environmental sustainability. It underscores the importance of continued research and technological advancements to unlock the full potential of agricultural waste in fostering a circular economy and driving sustainable development globally.

In the past few decades, the use of agricultural waste has been increasing due to the increasing demand for sustainable materials. This paper aims to review the significance of agricultural waste as a type of wealth and its potential as an alternative material in the composite field. It was found that many agricultural wastes had been utilized in various production of ecological products. The review discusses the physical, mechanical, and chemical properties of the natural fibers made from agricultural waste and the use of Pineapple Leaf Fiber Reinforced Composite to manufacture UAVs (Unmanned Aerial Vehicles). The extracted waste fibers’ physical, mechanical, and chemical properties show that these agricultural wastes can produce better advanced composite materials suitable for structural applications. The use of pineapple leaf fiber in Unmanned Aerial Vehicles manufacturing has the potential to revolutionize this industry and contribute to a more sustainable future.

The exponential growth in the consumption of electronics, in combination with the reduction in their useful life, leads to a significant increase in the volume of electronic material discarded. Printed Circuit Boards (PCBs) are modules composed of ceramic, polymer and metallic materials of high economic value and with a great potential for damage to biotic and anthropic environments when inadequately discarded. The aims of this work was to study the main environmental impacts and the efficiency of mechanical operations in the electronic waste recycling process in optimizing the concentration of metallic copper. For this, the samples obtained were characterized according to their morphology and chemical composition, and subjected to physical and mechanical treatments: dismantling, grinding, separation by granulometry, density and magnetic property. The environment impacts were estimated by the Life Cycle Assessment of the pre-treatment processes, associated with copper extraction operations in WPCBs. According to the results obtained, it is possible to infer that the NM +1mm Concentrated product presents in its metallic composition around 78% of copper, which contributes to the efficiency of the hydrometallurgical extraction processes. It is noteworthy that the Concentrated class represents about 14% of copper (wt) taking into account the amount of 3.789 kg of PCB waste input material. The potential for reinsertion of the dust in the material recovery process is highlighted, given that the chemical composition of this particulate has a significant presence of metals. In general, it was found that due to the higher concentration (wt %) of the sample being allocated in the range of - 0.15mm + 0.05mm, the elements Fe (18.30%), Si (10.73%), Ca (9.21%) and Cu (8.89%) stand out regarding the participation of the elemental composition of this fraction and also regarding the general composition of the sample. Furthermore, the generation of dust during the fragmentation process, can be associated with occupational respiratory diseases when not managed. About the Life Cycle Assessment, in seven of the nine categories evaluated, crushing and screening activities accounted for more than 90% of the recorded impact values. In general, it is estimated that in the pre-treatment phase be generated 15.4 kg CO2 eq.

Solid waste management is challenging in many countries, especially developing economies. The impacts of the pandemic continue to be felt and have indicated secondary impacts on waste management. This work draws on data on household solid waste (HSW), healthcare waste (HCW), and recyclables collected in the Rio de Janeiro municipality, analyzed from January 2018 to December 2022. As expected, the collection of HCW in Rio de Janeiro municipality experienced a noticeable increase in 2020 and 2021, with an average of 46.9 tons and 54.3 tons collected, respectively. Notably, 2021 saw a significant 30% increase compared to 2019 (p-value<0.001). No significant difference was observed in recyclables collected from 2018 to 2021. The average recyclable amount was 3,638 and 3,747 tons per month in 2020 and 2021. In contrast, the monthly amount was equal to 4,819.5 tons in 2022, representing an increase higher than 32% compared to previous years (p-value<0.05). Our findings can be used to adapt and improve waste systems to cope with similar emergency scenarios in the future, serving as a template for municipalities with similar challenges.

Given the importance of the development of urban infrastructure and environmental impacts produced by the civil construction waste (CCW), it is important to correct the handling of CCW with objective solutions that are more environmentally friendly. In that sense the present study aimed to determine indicators that make it possible to estimate the amount of CCW generated from construction sites in the city of Londrina, Parana State, Brazil. The generation of CCW was estimated in a general way, regarding the composition of its mixture, correlated to the gross areas of the buildings studied and their generated volumes of RCC. This generating rate was evaluated in a general way and specifies two types of sites: the new residential and new non-residential constructions. The data required for the development of these indicators was obtained through extensive survey and interviews carried out at the environment secretariat of the City Hall. The generating rate of CCW obtained for non-residential buildings was 0.2052m3/m2 or 170.44kg/m2, for new residential sites was 0.2054m3/m2 or 170.60kg/m2 and for new commercial or non-residential construction sites, it was 0.20453 m3/m2 or 169.85kg/m2. It was also possible to estimate the amount generated annually per inhabitant in the municipality, which is 0.60m3/inhabit.year or 498.55kg/inhabit.year.

Global wastes accumulate at an accelerating rate especially food and slaughterhouse waste constituting a major proportion owing to inefficient management. The high protein concentration of fish waste and keratinaceous byproducts is hazardous, harbouring pathogens, and emitting toxins. Transforming proteinaceous waste into amino acids (AAs) reduces waste bulk and offers a smarter nutrient approach for agriculture. However, this resource remains underutilized triggering eco-system pollution, diseases spreading, and climate change. Currently, small quantities of proteinaceous waste are valorized as animal feed, fertilizer, and in medical, and biotechnological sectors, which cannot solve bulk waste accumulation further, natural AA sources in agriculture are less recognized meanwhile researchers focus on synthetic AAs. Introducing various plant-nutrient formulas enriching fish AA with keratinaceous waste hydrolysate has not been broadly discussed. With this novel approach, using proteinaceous waste resources in agriculture would solve environmental pollution while minimizing land degradation by synthetic fertilizer. In this review, we illustrate the potential and benefits of valorizing proteinaceous waste in bulk through bioconversion. More importantly, we spotlight the biocompatibility of natural AAs and propose an enrichment, to use the ultimate product as catalysts for crops. Consequently, this approach reduces hazardous waste while paving a paradigm change in agriculture.

(1) Background: Food waste (FW) in Romania is 70 Kg/capita/year, while 70% of food waste comes from public catering, retail services, and households (over 50% – 47 million tons). (2) Methods: A cross-sectional observational study was conducted using an online questionnaire via the Google Forms platform from 15 April 2023 to 15 May 2023. The questionnaire was designed to assess various aspects, such as some socio-demographic information (age, sex, occupation, area of residence, study level, household members number, children &lt; 18 years of age); the personal involvement and frequency of food purchases and homemade food cooking; the main sources that generate food waste; the motivation and frequency with which food waste occurs; the level of awareness regarding the impact of food waste; the respondents' intentions regarding sustainable behaviors and practices food management; the level of information and familiarity of the respondents with the notions of validity and how these may influence their food consumption decisions. (3) The results show that FW incidence is occasionally (42%), very rarely (43.33%), frequently (15%), and no food waste was reported by 2.66% of respondents. The [35-44] age category records the highest FW frequency, followed by [18-24]. The most wasted are homemade food (29.67%), bread and bakery products (27.00%), and fruits and vegetables (14.33%). High involvement in purchasing and buying food following a previously established list reduces FW frequency. The same is valid for high daily involvement in food and homemade cooking. High interest in the FW problem and its perception as a waste of money leads to diminishing it, while guilty feelings increase the FW level (37.50% to 73.33%). (4) Conclusions: The present study shows that household food waste management is a multifactorial process that involves numerous socio-demographic, behavioral, and emotional aspects. Extensive data analysis supports our results, revealing deep self-reported information details and confirming its complex approach.

Sustainable bio-economy is considered to be one of the most promising routes towards the transition to a circular and climate-neutral economy. The valorization industry of bio-waste and agri-food by-products represents a key player in bioeconomy. In this article the design and the development of a web platform aiming at promoting synergies enabling the agricultural waste valorization is presented. The platform consists of: (i) the AgriPLaCE Waste Management Database which provides the users with an extended list of potential utilization measures for a variety of agricultural waste streams (ii) the AgriPLaCE Synergies Tool which aims to create synergies between different actors involved in the value chain from agricultural waste production to waste treatment and new valuable products’ exploitation. At the initial stage, the conceptual design of both tools took place by conducting an in-depth analysis for the user needs and services alongside the system architecture. Following, the AgriPLaCE platform development stage took place, with the implementation of all the necessary subsystems. The results showed that multiple potential collaborations can arise by the use of the AgriPLaCE platform, while users can also deepen on alternative and emerging treatment technologies and valuable products that can derive from a wide range of agricultural waste streams.

Increased construction activities in Australia have led to the generation of a massive volume of construction and demolition (C&D) waste annually. Management of this volume of waste requires an effective waste framework. The literature reported that the current Australian waste framework does not meet expectations and needs immediate improvements. This study was therefore conducted to seek the key C&D stakeholders' opinion about various issues identified in this waste stream. The specific objectives of this study are identification of the main barriers to effective C&D waste management, the impact of current regulations and opportunities to enhance the current C&D waste management system. A survey was conducted in 2019 to capture the stakeholders' perception. 132 participants from various industries and government agencies based in various Australian jurisdictions took part in the survey. The key results showed that the main barriers towards an effective management system are "overregulation, tough acceptance criteria, and increased testing requirements", "lack of local market" and "culture, poor education and low acceptance". Furthermore, a low number of participants indicated that the current legislation encourages waste recovery activities. The main areas of improvements included "providing a guideline that determines the accepted level of contamination for reusing C&D waste”, "preparation of guidelines on requirements of using recycled C&D materials in different industries" and "setting target for reduction, reusing, and recycling C&D waste". The results can inform policy development and be used as evidence for a broader discussion to solve lasting issues in C&D waste management.

The practice of collecting, treating and management of solid waste prior to disposal has become a necessity in developing and modern societies. Over the years, it is known that most wastes that are disposed have a second hand value. However, the construction cost for conventional Material Recovery Facility(s) (MRFs) has been a major barrier for implementation. These technologies require considerable technical expertise, which is often not available in developing nations to successfully operate the MRFs. Covenant University; a private mission institution through her waste to wealth scheme is focused on managing and processing used materials to reusable products. These include Pet bottles, Paper wastes, Food wastes from cafeteria, plastic food packs, nylon, tin cans and others. Specific areas chosen for the Survey include the residential areas for staff and students and the two cafeterias. The waste generated was characterized based on the waste stream so as to quantify the amount of recyclable waste generated and most occurring. The survey involved the use of structured questionnaires, on-site observations and measurements. The study reveals an average amount of recyclable waste generated per day in the institution as 13.46% pet bottles, 4.03% paper, 55.56% food waste, 12.64% plastic, 9.63% nylon and 4.68% tin cans. The study established that adequate waste characterization is a requirement for effective integrated solid waste management which would boost resource recovery, reuse and recycling.

Effective solid waste management is crucial for protecting public health and the environment. Global concentration on finding sustainable methods of handling waste continue to top the list of most governmental-related project checklists. This paper provides a case study on the management of municipal solid waste in the cities of Karlsruhe, Germany and Navrongo, Ghana as developed and developing countries respectively. This study aimed at comparing and drawing lessons from how these two different cities manage their solid waste. The waste management system in Karlsruhe prioritizes waste separation, recycling, and a pay-as-you-throw system has led to an efficient and sustainable waste management system that minimizes waste and protects the environment. Karlshrue's adoption of a continual developmental plan structure focused on integrated WM concepts is credited with safeguarding the long-term viability of waste management in the city. In contrast, Navrongo's waste management system faces several challenges, including inadequate resources and infrastructure, traditional waste disposal practices, and the lack of well-planned waste management strategies. To improve effective solid waste management systems in Ghana, a collaborative approach involving the government, local organizations, and the community is necessary. This can include investing in infrastructure, implementing waste separation and recycling programs, and educating the public on the benefits of sustainable waste management practices. Learning from successful models like Karlsruhe can help accelerate the development of sustainable waste management practices in Ghana, and ultimately protect public health and the environment.

Solid waste has become a tenacious issue worldwide. It has been increasing exponentially due to urbanization and the increase in the population. Since the twentieth-century technological revolution, there have been significant changes in the composition of solid waste. It poses significant challenges for waste management systems worldwide. Waste management is the process of handling waste right from its creation to its final disposal, including transport, collection, treatment, and monitoring. The present solid waste management (SWM) system is affected by unfavorable institutional, economic, technical, legislative, and operational constraints. Poor waste management is affecting ecosystems and human health, damaging our finite natural resources, impeding human economic progress, and harming people's quality of life. Now, researchers are concerned about the environment's degradation, a decline in quality of life, and risks related to waste management grow as the volume of solid waste. So, they are focusing on sustainable waste management practices which will be crucial for creating a cleaner and healthier environment for future generations. This chapter focuses on the concept of solid waste, its types, management, and its effect on the health of humans and the environment.

It is expected that due to the new UE regulation focus on waste management, managing kitchen waste will become more important in the future, especially in households. It is, therefore, crucial to develop user-friendly and odor-free containers to store kitchen waste. The study aimed to test the effectiveness of compost biochar in reducing noxious odors and volatile organic compounds (VOCs) released during kitchen waste storage. Varying quantities of compost biochar (0%, 1%, 5%, and 10%) were added to food waste samples and incubated for seven days at 20℃. VOCs released were analyzed on days 1, 3, and 7 of the storage simulation process. The results indicated that adding 5-10% of composts’ biochar to kitchen waste significantly reduced emissions in 70% of detected VOCs compounds. Additionally, Compost's biochar can be used to eliminate potential odor components and specific dangerous VOCs such as ethylbenzene, o-xylene, acetic acid, and naphthalene. A new composts’ biochar with a unique composition was particularly effective in reducing VOCs and could be an excellent solution for eliminating odors in kitchen waste con-tainers.

Demolished concrete and plastic waste are two increasingly aggravating problems. In this study, a novel method was proposed to simultaneously recycle concrete and plastic wastes by compacting concrete and plastic powders together under pressure and temperature. The influence of compression pressure and temperature as well as the mixture proportion on the bending strength of specimens was investigated. The results showed that pressure and temperature had a positive effect on the specimen strength; however, the molding temperature should not exceed the melting temperature of plastic. The proportion of plastic had a minimal effect on the bending strength of the specimen when plastic accounted for 25%–75% of the overall mass of the test piece.

Household waste is the primary source of environmental pollution due to global population growth compared to other sources of waste. This research aims to develop a smart and integrated household waste management system framework. The resulting framework not only focuses on dimensions of information technology but also links it with other integrated dimensions. This research attempts to conduct a Systematic Literature Review (SLR) using the Preferred Reporting Items for Systematic Review and Meta-analysis (PRISMA) protocol to produce a smart and integrated household waste management framework. The framework's design is carried out by identifying the type of household waste management process based on the Integrated Sustainable Waste Management (ISWM) framework, dimensions that support smart household waste management, and stakeholders involved. The SLR results, namely dimensions and subdimensions that support the framework of a smart and integrated household waste management system, were validated by a resource person from the Indonesian Ministry of Environment and Forestry. The smart and integrated household waste management framework that has been developed in this research contains five main dimensions: Information Technology, Operational Infrastructure, Governance, Economy, and Social-culture. This framework also addresses stakeholder engagement to support smart household waste management systems and identifies waste management processes based on the ISWM framework. This research uses the PRISMA technique to provide a framework for smart and integrated household waste management systems in the initial stage. The proposed framework has been validated and can be further developed as a smart and integrated household waste management system. This research also contributes to the involvement of various dimensions identified to deal with waste problems.

Vehicle routing is a critical factor in municipal solid waste (MSW) collection planning and operations. Poor routing can introduce inefficiencies and cause targeted levels of services or performance to be missed irrespective of the level of resource application. Trial and error approaches have been proven to be not the best in the planning and prediction of expected performance. This study explores various Geographic Information System (GIS) tools and analysis techniques, and how they can be applied to optimizing vehicle routes in light of challenging site conditions. Using Adentan West residential area, suburb of Accra Ghana as a case study, current performance of the trial and error method was measured and a GIS computer model was used to evaluate various optimization scenarios to determine the level of savings that can be made. Field measurements were taking with Global Positioning System (GPS) devices for waste collection activities in areas with varying characteristics and conditions, and data analysed for one selected vehicle operating four days per week. It was found that, for a scenario where only the bin collection order was optimized while route selection was restricted by the ArcGIS Network Analyst, 2.6% of travel distance and 2.21% of travel time were saved. For the second scenario where only the route selection was optimized while order of bin collection was restricted, 4.1% and 1.5% of travel distance and time respectively were saved. For a third scenario where both the order of collection and route selection were together optimized, 10.9% and 3.7% of travel distance and time respectively were saved. Lastly, by regrouping all the bins for daily collection, 4.5% and 1.2% of travel distance and time respectively were saved. The results demonstrated that there is always room for optimization of solid waste collection routing irrespective of site constraints and other challenges that the nature of bin distribution pose to drivers. In developing countries like Ghana, where there is high demand for services in the face of limited road network access, application of GIS in optimization of routes will guide providers in planning and subsequently make more savings in fuel consumption, vehicle maintenance and cost of man-hours.

In recent years, Malaysia has faced environmental challenges caused by municipal solid waste, especially household waste, during the Covid-19 pandemic. Among all the household waste, plastic and paper are the most prominent waste that causes environmental hazards. Several recycling associations in Malaysia have carried out their practices for better waste sustainability and management to curb the increasing amount of household waste. However, the effectiveness is still vague in achieving smart and effective household waste management. Therefore, this paper aims to investigate Malaysia’s household waste management, mainly in three significant municipalities in Malaysia for Kuala Lumpur, Penang and Melaka, in becoming a resilient and sustainable city by addressing two main research questions 1) What are the key factors for ensuring the more success move for future household waste management in cities? and 2) How will the 3 municipalities address their waste issues based on the key factors from RQ1, respectively? This paper reviewed 13 waste management articles and explores the potential of the four factors of waste management from the perspective of technology and data, economy, social and governance. The discussed factors and models contributed to an integrated future-proofing framework that focuses on smart waste tracking, an gamified awareness education, and strict policies to control waste management are the way forward for the future of smart cities household waste management.

Agricultural product like cassava produces huge amounts of waste when processed to consumable goods. The waste generated is generally considered to contribute largely to environmental pollution. This study therefore investigates the waste management practice that is adopted by cassava processors in Ogun State, Nigeria. Five (5) Local Government Areas (LGAs) dominant in processing cassava were selected for the study on the basis of spatial location distribution; landmass and population. The survey involved the use of structured questionnaires administered to cassava processors of the selected LGAs. The Statistical Package for Social Sciences (SPSS) software application and descriptive statistics were used for data analysis. Results of the analysis show that majority (70%) of the cassava processors are females. Cassava peel constitutes 10% of the waste produced, of which 91% are heaped at refuse dump in most communities. Results also reveal that 86.3% of cassava residues are used for animal feeds. Other findings show that the peels when dried are used as bio-fuel for cooking and there is a significant potential for biogas production. From the data captured from respondent during the study, most processors are willing to pay for an improved waste management system. The study therefore suggests proper waste management of cassava waste to minimize environmental pollution.

Target 12.3 of the United Nations Sustainable Development Goals (SDGs) calls for halving per capita global food waste at the retail and consumer levels, by 2030. The Food Waste Index is suggested as a methodology for grasping the situation. This paper focuses on the consumer level (household food waste). We argue that in order for generating useful information for devising and implementing effective measures for reducing food waste, it should be measured at Level 3 of the Food Waste Index, based on sorting analysis of generated waste, making a distinction between avoidable and non-avoidable food waste. Furthermore, a breakdown by sub-categories that reflect the flow of food in the household could help identify target behaviours. We have developed a categorisation scheme that is internationally agreeable and adoptable, and 1) generates useful information for policy-making and for tackling with reduction of food waste, 2) makes clear the concept of avoidable food waste, and 3) is practical and does not overcomplicate the work of grasping the situation of food wastage. Results of workshops regarding this scheme suggest that the scheme satisfies the criteria. This scheme has been applied to a few sorting analyses of household food waste in Japan, and their results are compared.

To encourage proper waste management from electrical and electronic devices (e-waste), it is necessary to invest heavily in the development of recycling technologies. One way to improve the process is to automate separating the shredded parts of e-waste using a robot. This paper's literature review, utilizing the Preferred Reporting Items for Systematic reviews and Meta-Analyses (PRISMA) framework, showcases potential robotic technologies for e-waste separation. However, the intricate design of these devices can pose significant challenges in their implementation. Various legal, organizational, and sociological obstacles have left Serbia's e-waste management practice underdeveloped, resulting in an unsatisfactory recycling rate. In this paper we examined the possibility of using robots on the precise example of recycling refrigerators in a recycling center in Eastern Serbia, concluding that such a solution would have multiple positive effects, both on the employees and the working environment, on the operations of the recycling center itself, and on increasing the e-waste recycling rate in the country.

Singapore, being a land-scarce country, is heavily dependent on imported food, which poses a challenge in ensuring food security. In addition, the substantial amount of food waste generated in Singapore further deepens food insecurity challenges, imposing enormous pressure on the country's food and land resources. In the recent years, valorising food waste streams into higher value products has been an increasing trend in tackling food wastage due to its economical and environmental benefits. This paper provides a thorough review on food waste valorisation in Singapore and summarizes critical information from the current food landscape to the food waste management strategies adopted. The review highlights the prototypes developed from food waste streams by the local research and development capabilities and the technological processing and techniques used for versatile applications ranging from food and nutraceuticals to urban agriculture. The challenges associated with the valorisation of food waste are also addressed. Two ambitious Initiatives by the Singapore government Zero Waste Plan and the 30-by-30 food security goal to encourage food waste valorisation are explored and presented. The review serves as a reference for other countries in ensuring food security and achieving sustainable development goals.

This paper examines the relationship between GDP per capita and waste generated in European Union countries, highlighting the importance of this relationship for understanding the environmental consequences of economic growth and formulating waste management policies. The analysis findings demonstrate that, in most cases, higher GDP is associated with higher amounts of waste, although there are exceptions to this trend. A smaller number of countries are also found where no such relationship exists. These are primarily high-income countries in the lower part of the EKC or countries in transition. Cluster analysis reveals regional differences in the relationship between GDP and waste that the economic factors and the level of development in the regions concerned can explain. Bulgaria is among the European countries with the lowest economic growth associated with a large amount of waste. The analysis, therefore, focuses on Bulgaria. The impact of GDP per capita, Human Development Index and Population Density on municipal waste in Bulgaria is studied. The aim is to identify significant relationships and dependencies between these factors and the amount of waste. Based on the results of multiple regression analysis and the findings from municipal waste management data in Bulgaria, specific actions are proposed for municipal waste management in the country. Recommendations are made for developing sustainable waste management policies and sharing best practices between regions.

Valorization of food and fruit wastes has the potential for the production of sustainable energy and biochemicals. Approximately 70% of the weight of the original jackfruit (Artocarpus heterophyllus L.) fruit is lost during processing as waste in the form of peeled skin and core, both of which have not been utilized and, thus contribute to disposal as well as pollution issues. The major components, cellulose, and hemicellulose, can be biologically transformed easily into bioenergy sources like ethanol, methanol, and butanol; valuable phenolics and biotechnological products like pectin, citric acid, bromelain, ferulic acid, and vanillin; and many other products. These residues can also be utilized as essential sources for the biological transformation process leading to the production of numerous products with added value, such as phenolic antioxidants, phenolic flavor compounds, and organic acids. Thus, the value addition of jackfruit waste can support the sustainable solution towards food and nutritional security. In this way, zero waste can be achieved through novel biorefineries which are critically highlighted in this paper. Furthermore, novel technologies for the conversion of jackfruit wastes are summarized with recent findings.

Computer vision methods have shown to be effective in classifying garbage into recycling categories for waste processing, existing methods are costly, imprecise, and unclear. To tackle this issue, we introduce MWaste, a mobile application that uses computer vision and deep learning techniques to classify waste materials as trash, plastic, paper, metal, glass or cardboard. Its effectiveness was tested on various neural network architectures and real world images, achieving an average precision of 92% on the test set. This app can help combat climate change by enabling efficient waste processing and reducing the generation of greenhouse gases caused by incorrect waste disposal.

Recycling and waste management have garnered immense popularity in recent years, but few studies have been carried out regarding these systems. Therefore, an in-depth literature review was done in order to highlight the different sectors of the recycling system that need to be reformed. Hence this study examined recycling and waste management systems within three categories–medical, municipal, and plastic–that were carried out pre and post COVID by reviewing previous studies, technical reports, and annual reports. This was done by visiting numerous academic search engines alongside online resources that were utilized to assemble literature related to waste and recycling systems. Continuing a recurring idea was that no matter the type of waste, further research regarding all waste should be carried out. Additionally, since recycling and waste management are a vital part of our society, and seeing how unpredictable events such as the pandemic may be, it is paramount that that research is done not only on how the pandemic has affected systems now, but also how we can learn from current issues to utilize them for future “waste shocks”.

Despite the increase in popularity of Zero Waste (ZW) concept, the successful implementation of this concept in waste management is still facing many challenges. The plastic recycling rate in Australia is currently only about 9.4%, which could leave up to 90.6% of plastic consumption being sent to landfills. The state of Victoria (in Australia) has proposed an ambitious plan to upgrade its waste and recycling system and to divert about 80% of waste from landfills by 2030. The aim of this research is to study Victoria’s current waste management plan and to develop a simulation model to assess the feasibility of it achieving zero plastic waste by 2035. In this direction, a fundamental knowledge of global ZW implementation needs to be acquired in order to understand the challenges, obstacles, and uncertainties in achieving ZW target. A simulation model is established using a method called double baselines. This method was developed as an improvisation to address the limitation of data availability for the model development. The model will run on 4 scenarios including one from Victoria’s current plan. Outcomes from the model are produced in comparative charts covering 6 key considerations including the rates of plastic consumption, waste to landfill, diversion, recycling, relative accumulative cost and effort. The findings of this study pointed out that Victoria’s current plan are feasible for its goal and presented with opportunities for improvement especially towards zero plastic waste. Besides, study results also reveal that the Victoria’s current plan to achieve 80% diversion rate by 2030 is possible but the zero plastic waste target by 2035 is less likely to happen.

Ghana spends over $4000 (US dollars) annually managing municipal solid waste (MSW) with little improvement in regional sanitation. Energy demand in the country is also on the rise. Therefore, addressing waste problems via the waste-to-energy valorization approach is necessary for dual benefits. This paper thus seeks to comprehensively review Ghana's MSW's proximate and ultimate compositions for biological and thermochemical conversions. Studies between 2011 and 2024 were analyzed. The findings revealed that the organic fraction of Ghana’s MSW is currently about 10.47Kt per day. The proximate analysis reveals a moisture content from 13.55 – 61.9 %, volatile matter ranges from 6.24 - 80.25%, and the calorific value ranges from 14.96-21.46MJ/Kg. The ultimate analysis revealed that the carbon-to-nitrogen ratios range from 24.3-32.2, and the hydrogen content ranges from 5.53-22.8%. The sulphur and nitrogen contents were below 0.6 and 1.7% respectively. Approximately 2,534.65 GWh of electricity is estimated from the organic fraction. Ghana’s MSW is more suited for biochemical conversions.

Nowadays the preservation and restoration of historical building needs to be faced in accordance with a novel sensibility regarding environment to preserve the future generations. In this context, the scientific community is focusing on novel and sustainable materials and techniques allowing durability and mechanical performances and at the same time compatibility with the existing heritage. Alkali activated materials represent a great challenge to produce new materials starting from the existing ones with reducing consumption, emission of greenhouse gases and environmental impact. This study deals with the valorization of waste materials coming from demolition and construction activities in the manufacture of geocomposites suitable for restoration and conservation of historical heritage. In particular, waste from tuff sawing and brick grinding were used as raw materials, then the geopolymeric samples produced were characterized from physical-chemical and mechanical point of view in order to investigate their performance and evaluate their suitability as materials for historical buildings recovery. Brick waste based geocomposites resulted to be more compact than the tuff-based ones as showed by the higher density values and the lower values of open porosity and water absorption and as further confirmed by the trend of the mechanical performance. Moreover, experimental data showed that physical and mechanical properties of both bricks and tuff waste-based geocomposites, even with different waste content, are compatible with existing building materials and to all the traditional repairing products.

Indonesia's government anticipates waste problems by managing them through a large number of waste reduction programs. From a governance perspective in Indonesia, it is known that actors from diverse governmental levels and across sectors are involved in waste management, and their involvement largely depends on their institutional goals and problems. Hence, they are expected to coherently collaborate together by developing and implementing sustainable instruments and resources for improving waste management problems. However, it is necessary to understand how supportive and restrictive the governance of waste reduction programs is to encourage successful trash reduction. This study is designed to evaluate and examine the application of Community-Based Solid Waste Management (CBSWM) in Makassar. In this research, The Governance Assessment Tool (GAT) was applied to analyze the governance context of the waste reduction programs in Makassar qualitatively. From the assessment, contexts can be described as either supportive or restrictive of the processes of implementing public policies on waste management. As a result of such an assessment, this study shed light on some opportunities to improve the governance of waste management implementation's impact on reducing waste in Makassar, South Sulawesi, Indonesia. The conclusion of this study depicts that the most important actors are affiliated with the local government and the community. Moreover, this study shows that the assessment of contextual governance is predominantly restrictive.

Economic development and population growth lead to increased production of chicken manure (CM), which is a problematic organic waste for its amount, environmental threats, and moisture content. There are different ways of CM, namely anaerobic digestion, composting, combustion, and direct land spreading. Hydrothermal carbonization (HTC) is another emerging way, however. In this study, the HTC of CM was performed to produce energy-rich material called hydrochar (HC). The effects of HTC temperature (180, 240, 300 C) and process time (30, 90, 180 min) were summarized. Proximate and ultimate analysis, as well as heating values (HHV, LHV), have been performed both on raw CM and derived HC. Additionally, the process performance has been examined. The obtained results show that HTC is a feasible method for CM disposal and valorization. Although process time did not influence considerably fuel properties of CM, higher temperature led to significantly higher HHV, reaching 23,880.6734.56 Jg-1 at 300 C and 180 min with an improvement of 8,329 Jg-1 compared with raw CM (15,551.67 Jg-1). The process conducted at 240 C in 30 min has been specified as the most favorable, due to the highest energy gain of HC and relatively low energy consumption.

Liability to prevent consequences of an unhealthy situation due to accumulating toxic and hazardous emissions caused by open dumping of municipal solid waste with increasing urbanization has necessitated a renewed thinking on waste disposal. Grate fired incineration systems were adopted by urban managements in past and present but with criticisms due to formation of air borne emissions. Improved combustion methods like fluidized bed are now propagated because of current requirements like efficient energy recovery potential, stricter emission norms, adaptability with urban growth, adaptability to co-firing with other waste like biomass, edible oil wastes or industrial effluent and integration with conventional energy generation. Such a comprehensive and futuristic approach is more sustainable for the community. Multi-criteria decision-making tool is used to identify the best technology option among grate combustion and fluidized bed combustion for disposing and energy recovery from waste. Ten different collection and disposal options involving two combustion methods, namely, grate combustion and fluidized bed method are considered. Utilization of the energy is done for three end uses, namely, power generation, water distillation and district cooling. Two different regions in Saudi Arabia are considered for this study under two types of scenario, namely with recycling and without recycling. The different options are prioritized based on their overall ranking using five major performance factors.

To date, only a few studies focused on carbon monoxide (CO) production during waste composting; all targeted on CO inside piles. Here, the CO net emissions from compost piles and the assessment of worker’s occupational risk of exposure to CO at large-scale composting plants are shown for the first time. CO net emissions were measured at two plants processing green waste, sewage sludge, or undersize fraction of municipal solid waste. Effects of the location of piles (hermetised hall vs. open yard) and turning (before vs. after) were studied. Higher CO net emission rates were observed from piles located in a closed hall. The average CO flux before turning was 23.25 and 0.60 mg‧m-2‧h-1 for hermetised and open piles, respectively, while after – 69.38 and 5.11 mg‧m-2‧h-1. The maximum CO net emissions occurred after the compost was turned (1.7x to 13.7x higher than before turning). The top sections of hermetised piles had greater CO emissions compared to sides. Additionally, 5% of measurement points of hermetised piles switched to ‘CO sinks’. The 1-h concentration in hermetised composting hall can reach max. ~50 mg CO∙m-3 before turning, and &gt;115 mg CO∙m-3 after, exceeding the WHO thresholds for a 1-h and 15-min exposures, respectively.

Various metals and semiconductors containing Printed Circuit Boards (PCBs) are abundant in any electronic device equipped with controlling and computing features. These devices inevitably constitute E-waste after the end of service life. The typical construction of PCBs includes mechanically and chemically resistive materials, which significantly reduce the reaction rate or even avoid accessing chemical reagents (dissolvents) to target metals. Additionally, the presence of relatively reactive polymers and compounds from PCBs requires high energy consumption and reactive supply due to the formation of undesirable and sometimes environmentally hazardous reaction products. Preliminarily milling PCBs into powder is a promising method for increasing the reaction rate and avoiding liquid and gaseous emissions. Unfortunately, current state-of-the-art milling methods also lead to the presence of significantly more reactive polymers still adhered to milled target metal particles. This paper aims to find a novel single and two-stage disintegration-milling approach that can provide the formation of metal-rich particle size fractions. The morphology, particle fraction sizes, bulk density, and metal content in produced particles were measured and compared. Research results show the highest bulk density (up to 6.8 g·cm-3) and total metal content (up to 95.2 wt. %) in finest sieved fractions after the single-step milling of PCBs. Therefore, the concentrations of about half tested metallic elements are higher in the single milled specimen and with lower adhered plastics concentrations, as compared to double milled specimens.

Healthcare waste presents a global environmental and public health issue, with the U.S. generating over 5 million pounds annually. Hospitals have initiated programs to reduce waste and enhance recycling, with encouraging outcomes. At our tertiary medical center, disparities in municipal waste disposal across departments led to targeted research in the Surgical Intensive Care Unit (SICU). We evaluated the effectiveness of an educational intervention aimed at improving red bag waste management. Pre-intervention audits assessed waste sorting, followed by one-minute staff presentations and infographics near disposal bins. Post-intervention audits revealed a significant reduction in inappropriate municipal waste in red bag bins, analyzed using Fisher’s exact test. Interviews suggested staff lacked recollection of prior red bag waste training, underscoring the value of continuous education. While effective, limitations included sample size and generalizability. Future studies should explore additional strategies to further improve waste disposal practices and address training gaps.

The Brazilian Policy foresees the waste management hierarchy, according to which energy reuse from waste is preferred to final disposal. However, less than 0.2% of the country's waste goes to energy production. This paper proposes sustainability indicators to support the decision to choose the best process to treat municipal solid waste (MSW) through bioenergy generation technologies. Then, we conduct a case study for Rio de Janeiro. Incineration and gasification were not economically feasible – despite TRL 9 and 8. However, the projects presented null net present value by increasing the gate fee to 94.69 and 255.39 USD/ton of MSW, respectively. The social indicators (job creation, salary increase with the absorption of waste pickers, population served, reduction in MSW sent to landfill) did not indicate the best technology. The results of the environmental indicators for incineration and gasification were, respectively, 0.45 and 0.37 t CO2eq/tMSW for GWP, 1.49 and 1.23 MWh/tMSW for energy intensity, 1.24 and 6.14 m³/tMSW for water intensity, 39.3 and 27.9 m²/tMSW for land use and 0.135 and 0.088 t SO2eq/tMSW for acidification. Gasification presented better results on 60% of the environmental indicators. However, incineration was better in important ones, water and energy intensities, besides the technical-economic aspect.

The consistent and continuous growth in the world’s population is creating many challenges for public policymakers in the different life areas, including dealing with the increasing amounts of waste that are generating problems involving air and land pollution and a shortage of land for waste disposal. This study presents the results of public policy on managing municipal waste, as manifested in the quantity and rate of waste collected throughout Israel in recent years and disposed of in the various landfills and in analysis of the political and economic factors affecting this policy. The study combines a quantitative and qualitative approach, where the quantitative study includes analysis of statistical data based on information from the Central Bureau of Statistics, the Ministry of Environmental Protection, the Ministry of Finance, and others, and the qualitative study relies on reading and analyzing primary documents of the different government ministries on Israel’s waste disposal policy and information in the media on this issue. The research findings attest to an increase in the amount of municipal waste dumped in Israel, a merely slight decrease in the rate of landfilling as a proportion of all municipal waste disposal, and a merely slight increase in the rate of municipal waste recycled in recent years. The research conclusions stress the effects of the landfill levy and the Cleanliness Maintenance Fund on one hand, and of the government instability in the Ministry of Environmental Protection, the positivist policy embraced by decision makers in the Ministry of Environmental Protection, and the power struggles between Israel’s different ministries on the other, as the respective economic and political factors affecting Israeli policy on municipal waste management.

A large amount of concrete waste is generated around the world and its recycling is an urgent issue. In this research, a new approach to recycle concrete waste with wooden waste was studied. Concrete and wooden wastes were crushed, mixed, and heat compacted to produce plates with different water contents and mix proportions at various temperatures, pressures, and durations of compaction. The bending strength of the plates was measured after compaction. The result indicated that with an increase in the percentage of wooden waste in the mixture, pressure, or temperature improved the bending strength. The increase in water content reduced the bending strength. Most of the products exhibited higher bending strength than that of ordinary concrete.

The increasing importance of batteries in the 21st century and the challenges posed by the anticipated growth in end-of-life batteries, particularly in Europe, are addressed. Projections indicate a significant increase in battery waste, with a specific focus on the recycling of black mass (BM)—a complex and hazardous byproduct of the battery recycling process. The research employs the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) methodology to systematically analyze the hazardousness of BM derived from various types of batteries. The findings reveal the inherently hazardous nature of BM, classifying it under multiple hazardous properties (HPs) according to European regulations. The urgent need for a definitive legislative classification of the hazardousness of BM is emphasized, and the potential of innovative technologies and strategies to improve recycling performance while mitigating risks is highlighted. The research significantly contributes to understanding the complexities of BM recycling, providing a foundation for future advancements in this area and emphasizing the need for further exploration and economic feasibility analysis of recycling technologies.

Industries are required to utilize treatment technologies to reduce contaminants in wastewater prior discharge and valorize by-products to increase sustainability and competitiveness. Most acid leaching gypsum purification studies have obviated the treatment of the highly acidic wastewater produced. In this work, acidic wastewater from acid leaching purification of post-consumer gypsum was treated to recover a valuable solid product and reusable water. The main aims of this work were to determine the impact of recirculating acidic and treated wastewaters on the efficiency of the acid leaching purification process and to valorize the impurities in the wastewater. Samples were characterized through X-ray fluorescence and X-ray diffraction. SimaPro 9.5 and ReCiPe 2016 midpoint method were used for the life cycle assessment of three wastewater management approaches. The reuse of the acidic wastewater did not improve the chemical purity of gypsum. Soluble impurities were precipitated at pH 10.5 as a magnesium-rich gypsum that could be commercialized as fertilizer or soil ameliorant. The alkaline treated water was reused for 6 acid leaching purification cycles without impacting the efficiency of the purification process. An acid leaching-neutralization-filtration-precipitation approach demonstrated superior overall environmental performance. Barriers and enabling measures for the implementation of an in-house wastewater treatment were identified.

The issue of sustainability has long been the subject of interest of the architecture engineering and construction sector. All three aspects of sustainability - economic, environmental and social - can be affected through appropriate construction waste management. Construction and demolition waste (CDW) is one of the largest worldwide waste streams, therefore it is given great attention by all stakeholders (investors, contractors, authorities, etc.). Researches have shown that one of the main barriers to insufficiency CDW recovery is inadequate policies and legal frameworks to manage CDW. It is also one of the EU's environmental priorities. Aim of the article is to confirm the economic potential of construction and demolition waste audit processing through case study. A pre-demolition waste audit has been processed for unused building of shopping center in the town Snina in Slovakia. Subsequently, a comparison of economic parameters (waste disposal costs and transport costs) of recommended CDW management was performed. This comparison confirmed the economic benefits of environmentally friendly construction waste management methods according to the waste audit results, which will also increase the sustainability of construction projects. In addition, the cost parameters of selected waste disposal methods could be another dimension of building information modelling.

Thermal plasma is a versatile technology that can be used to treat various types of wastes, including vegetal and mineral oils, solvents, plastics, papers and cardboard, glasses, bricks and rocks, metals, clothes, and mixtures of these materials. In this study, we utilized a commercial plasma cutter as a thermal plasma source to decrease the volume of a simulated low-level radioactive mixed solid waste. The simulated waste included papers, plastics, clothes, gloves, metals and stable Co, Cs, Sr, and Ce additives as surrogates of 60Co, 137Cs, 90Sr, and 144Ce, the latter typical contaminants in nuclear LLW. As a result of the process two products were obtained, a solid phase in which we focused this work and a gaseous phase. To retain as much as possible surrogates in the solid final phase, crushed glass from broken bottles was included as a vitrification additive to the original waste. After undergoing heat treatment, a dense vitreous slag was produced and ashes. The process resulted in a volume reduction of 70%, indicating the successful gasification of organic excess materials. The surrogate elements were retained in the process and were found in the ashes composition: Co (3.4% w/w), Cs (37.7% w/w), Ce (0.6% w/w) and in the glass matrix composition of Co, Cs, Sr and Ce: 72.4 ± 14.7, 32 ± 18.2, 125.3 ± 31.6, 80 ± 13.1 % w/w respectively. For the actual experimental conditions, retention efficiencies were estimated for Cobalt (Co) at 72.4 ± 14.7%, Cerium (Ce) at 80 ± 13.1%, Strontium (Sr) at 125.3 ± 31.6%, and notably Cesium (Cs) at 32 ± 18.2%.

The purpose of this study is to assess the solid waste management status and practice in Sendafa town, Oromia regional state residents. In order to achieve this goal, the researcher intends to employ both primary and secondary data from the Sendafa town municipality. With the aid of multi-cluster sampling and a purposive sampling method, the researchers chose a sample size of 398 people and 10 interview responders. To utilize a systematic sampling technique at intervals of residences, individual samples were chosen. Quantitative data was cleaned and analysed using STATA software. A multiple linear regression model and logistic regression other descriptive statistics methods were then used to change the results. The qualitative data were imported, coded, and thematised using ATLAS.ti.9 in order to prepare respondents' interviews for analysis. The findings indicate that residents' poor solid waste management practices are a result of a lack of awareness, low family income transportation issues, issues with waste collectors, a lack of a sense of responsibility and belonging, and a failure to enforce current solid waste management laws. Solid waste accumulates near roads, bridges, and residential areas that are close to landfills, contaminating the area and leading to diseases like TB and Asthma (and other related health issues in children and adults who live there). Thus, researcher recommends that to have sustainable solid waste management the town administrators should have plan to develop awareness creation symposium or panel of discussion, resolve transportation issues, monitor and guide the routine activities of waste collectors, develop sense of belongingness for themselves and for the community, develop integrated solid waste land fill projects and working with all stakeholders like NGO and health institution will minimize the adverse effect of improper solid waste management. Keywords: Solid Waste, Status of Solid Waste Management, Land fill site suitability

In the last ten years, plasma waste treatment has gained increasing prominence as a technology in response to growing challenges in waste disposal and the recognition of opportunities for generating valuable by-products. The efficiency and outcomes of this process are intricately linked to the characteristics of the plasma involved, such as plasma enthalpy and heat flux. We employed an experimental radio frequency inductively coupled plasma (RF-ICP) torch operating at atmospheric pressure to generate plasma. Utilizing optical emission spectroscopy (OES), we measured plasma parameters, specifically the effective electron temperature (Teff) and plasma density (ne), while varying argon gas flow rates and RF powers. Our investigations revealed that both flow rate and RF power exert significant control over plasma parameters, and we observed an unusual phenomenon within this range of discharge pressures. Consequently, both the plasma's enthalpy and the heat flux it generates are influenced by variations in both flow rate and RF power.

Enzymes are biological molecules produced by living entities for carrying out biological processes. The application of enzymes for waste treatment has been gaining pace commercially to solve concerns related to agricultural residues, wastewater, replacement of synthetic processes with natural ones, etc. The application of enzymes for waste management has been an environmentally reliable and sustainable process. Treatment of waste with enzymes such as xylanase, proteases, hydrolases, cellulose, peroxidases, chitinases, laccases, etc. has been studied to be effective. These enzymes act upon the waste products and transform them into biodegradable forms that can be recycled, reused and converted to value-added products. They have wide applications and utility as it has been an effective approach, economically cheaper and sustainable techniques. Application of such enzymes for waste management would be beneficial for reducing the quantity of waste, diminishing the negative effects of waste and pollution on the environment, and would be beneficial in bio-converting the waste products into alternate sources of energy. The current chapter focuses on different types of enzymes, their applications for waste management, and their limitations. This chapter also emphasizes the usage of some prominent microorganisms, their secreted enzymes and their proposed mechanisms of action involved with the degradation of the waste products.

Cigarette butts (CBs) are the most diffuse waste in the world, often abandoned in the environment without proper disposal. They are dangerous because of the numerous harmful chemicals poten-tially released in the environment. There are, in literature, several technological options for CB recycling, but some critical concerns could affect their effectiveness due to the quality and quantity of CB litter collected in the proper way. The present paper focuses on policy framework social behavior, waste collection and transport and technological processes. The Extended Producer Responsibility scheme for CBs is proposed at European level as an action to tackle CB litter and encourage sustainable product development. The CB waste collection and transport is a key step for bringing CB to the recycling process. The main concern is the small quantity of CBs collected: 0.06 % of the municipal waste and 0.18 % of the unsorted waste in the administrative area of Pe-rugia. Another crucial issue is the need for behavioral interventions to increase education and awareness of smoker citizens, addressing the discrepancy between smokers’ behaviors and beliefs.

Fruits are commonly used, fresh or processed, to prepare different industrial products with superior nutritional and health-promoting properties. Currently, the demand for processed fruit products has motivated the rapid growth of the fruit processing industries, persuading them to produce an enormous amount of by-products with less utilization. Furthermore, people's shifting dietary habits and lack of awareness of nutritional properties result in an avoidable load of fruit by-products. The knowledge of the value of by-products urges exploration with proper documentation, emphasizing the health benefits of some such products. Hence, this review is prepared by carefully analyzing the recent literature on industrial applications of fruit by-products and their nutritional and health-promoting properties. The use of fruit by-products in food industries for various purposes has been reported in the past and has been reviewed and described here. Fruit by-products are a good source of nutrients and bioactive components, including polyphenols, dietary fibers, and vitamins, implying that they could have an important role for novel, value-added functional food properties. Furthermore, fruit by-products are used as the substrate for the production of organic acids, essential oils, enzymes, fuel, biodegradable packaging materials, and preservatives.

The growing concern about climate change and the recognition of the planet’s limits led society to look for alternatives that promote the balance between the natural and the built environment. The circular economy emerges as an alternative to the linear economic model, inspired by natural metabolisms, by circulating resources in continuous loops, where their intrinsic value is maintained and improved. This research proposes a closed-loop strategy in the built environment by studying innovative constructive solutions that aim to find use, value, and inspiration in what is considered waste. A literature review is conducted on the circular design strategies, re-use and recycle typologies, and waste transformation processes. Then, the development of a methodology for qualitative evaluation and selection of re-used and upcycled construction materials from post-consumer waste and by-products is presented and then applied to thirty-five cases of constructive solutions from plastic, wood, paper, steel, aluminium, and agricultural waste. The research reports that the developed framework is adequate. The analysed alternative materials have good environmental performance and can be used as building materials despite their functional limitations, reflecting the enormous potential of waste as a resource for the construction industry.

The nationwide lockdown imposed to control the spread of novel coronavirus induced dramatic alterations in different sectors of the Nepalese governance, including Solid Waste Management (SWM) practices. The study identifies SW collection gaps in seven major cities of Nepal and highlights the municipal and public households on SW management practices before and during the lockdown to emphasize the linkage between COVID-19 and SWM. It includes information on solid waste status, collection frequency and coverage, workers safety practices, types of vehicles operated for collection and alternative methods adopted by households to manage SW during the lockdown. For this, 1329 households survey and key informant interviews were conducted in seven cities of Nepal during the lockdown. It was found that although the coverage of the collection service was similar during the pandemic, there was a drastic decrease in the collection frequency leading to a collection gap of around 570 tons/day. More than 50% of the surveyed households adopted no proper alternative measures as they claimed that they stored solid waste with proper management so that municipal authorities can take it. The study reveals poor occupational health and safety practices among the solid waste workers due to the unavailability of safety gears and equipment despite being aware of the modes of transmission of the virus. The pandemic exacerbated the challenges of smooth SWM as it is an essential and needy service. This study highlights the need for a timely strategic management framework to be developed by the government to continue the smooth SWM practices during the lockdown.

Botanical recycled concrete, or concrete bonded with wood, is formed by heat pressing the mixture of concrete and wooden waste. Botanical recycled concrete is a relatively new material and the relationship between production condition and its real-world performance is not clear yet. This experimental study investigated the influence of several production condition factors on the density and bending strength of botanical recycled concrete. As a result, temperature and mass ratio of concrete powder to wood flour presented significant effects on the density of this botanical recycled concrete. The increase in production temperature resulted in a remarkable increment in density and bending strength. This is probably due to increased wood flowability and accelerated compaction and bonding formation. The fineness of wood flour had a significant effect on improving bending strength. This is attributed to a larger contact surface between the wood substance and concrete particles.

Global waste generation keeps increasing over the year and requires innovative solutions to minimize their impacts on environmental quality and public health. Predicted 2.2 billion tonnes per year of global municipal waste generation in the year 2025 which 1.6 fold is higher than in 2012. Hence, a strategic plan must be ascertained to overcome the future challenges of MSW locally and globally. Universiti Putra Malaysia (UPM) coined an initiative to demonstrate a showcase pilot plant for green energy production from MSW. Therefore, the data was obtained from the survey and actual sampling within the UPM compound to estimate the MSW generated and it's potentially used for green energy production. It is estimated that 5.0 – 7.0 tonne per day of MSW generated which about 30 - 35% is an organic fraction. Upon separation, the organic fractions were digested into biogas through anaerobic. At the maximum conversion of organic fraction, about 775 kWh of electricity may able to generate from the waste. In this study, the complete biorefinery setup and utilize organic components from the MSW generated in UPM was proposed that the biogas subsequently will be used to produce green energy in the form of electricity or cooking fuel.

Recent years have experienced an increase in construction and demolition waste (C&amp;DW), which is the most significant solid waste stream. C&amp;DW is contributing to exceeding all planetary boundaries and presents a range of other issues. In order to better understand the existing research on C&amp;DW, a global bibliographic analysis was undertaken through seven groups of keyword searches and the results visualised using VOCviewer. The results show that C&amp;DW receives only a modest research attention compared to other areas of waste, and this is despite an exponential increase in C&amp;DW research since 2016. The analyses also show that concrete is the most researched material in terms of C&amp;DW, and that reuse, recycling, and circular economy are so far attracting only proportionally modest research attention. This signals a need for further acceleration of the C&amp;DW research, and specifically for more research on reuse, recycling, and circular economy for materials other than concrete.

The possibility of making precious stones from radioactive waste is being considered. Vitrified and cemented radioactive waste (RW) is considered as an artificial rock belonging to aluminosilicates and calcites. Two methods are proposed for the manufacture of radioactive gemstones from RW and their subsequent storage with the possibility of sale, resale, inheritance, and so on. That is, RW is considered as real estate in which capital can be invested. After decontamination in hundreds and thousands of years, it will be of scientific, historical, jewelry interest.

The new climate law introduces a policy of sustainable construction, the assumption of which is the reduction of CO2 by the construction industry and the use of environmentally friendly materials, such as agricultural, mineral, and recycled waste, while limiting the consumption of natural resources. The article is a literature review that analyzes selected waste materials from various sectors of the economy that can be used as additives or partial substitutes for natural resources in the production of cement and in and cement building materials, the production of which reduces CO2 emissions, producing materials with high mechanical strength and environmentally friendly.

An adequate number of waste management facilities is the key element to meet circular economy goals. Using empirical data taken from official sources the research framework bases on an econometric model to compare the elasticity of cost on quantity of different alternatives such as waste-to-energy facilities, mechanical biological facilities and landfills impact on waste management cost. Results suggest that both waste-to-energy facilities (-0.278%) and landfills (-0.38%) concur to lower the cost while the higher the percentage of waste sent to mechanical biological treatment facilities, the higher the cost (0.788%). This figure deserves to be examined in more details as such facilities represent an intermediary step in the chain which efficiency depends on the industrial organization of the chain.

Whereas waste management research has focused on mostly urban municipalities in South Africa, not much is known about the current performance of waste management services from the perspective of community residents in rural municipalities. This study reports on the status and effectiveness of waste management practices from the perspective of community residents in the Umkhanyakude and Zululand Districts in the rural areas of the KwaZulu-Natal province of South Africa. Making use of structured questionnaires, primary data was obtained by interviewing 333 respondents representing households in the study area. Results have revealed several shortfalls in the provision of municipal waste management services, except for solid waste removal from households (66%), and management of landfill sites (41%). The degree of dissatisfaction for waste management services rendered was very high (97.3%). Furthermore, the majority (61.4%) of respondents were not willing to participate in waste segregation due to lack of appropriate knowledge and infrastructure. The study also pinpointed some benefits associated with waste minimization, as well as barriers constraining effective waste recycling. Based on these findings, there is a dire need for transforming current waste management practices toward increased recycling rates by creating more environmental awareness and a supporting infrastructure.

The use of food waste disposers in gastronomical facilities influence the municipal wastewater composition. Ground food waste poses problems in the operation of the sewerage network and generates high electric energy consumption in wastewater treatment plants (WWTP). The study aimed to determine, for five towns with a PE of 4,000 to 220,000, the volumes of catering waste discharged to the WWTPs. The towns differed in the number of inhabitants, beds in hotel and catering places. The calculations were made based on data received from the operators of WWTP. The pollutant concentrations in 2019, were compared with data from the "pandemic" year - 2020. The loads of catering waste entering the sewerage system in 2019 ranged from 32.7 to 1062 tons. In town with the largest tourist base, the BOD value in 2020 accounted for 62.3% of 2019 value. In the largest town, the annual energy consumption for food waste treatment could be up to 2,539,770 kWh. If the waste was fermented, it could be obtained up to 1,376,650 m3 of methane. There is a strong need for implementing a collection system for food waste from catering facilities and its fermentation to produce methane, which can be used for energy purposes.

Any Hospital’s primary goal is to restore human health and save lives through health services provided to patients, but at the same time, hazardous wastes are produced. Inconsistent management of unsafe wastes might cause adverse effects and other issues to workers, the environment and public health. Segregation is considered the critical stage for a successful Healthcare Waste Management. Mixing hazardous waste with non-hazardous waste will be avoided by correctly applying practices at the segregation stage. This study aimed to assess personnel’s knowledge about Infectious Medical Waste and segregation practices used at six wards in Nicosia General Hospital. An analytical cross-sectional study was conducted, and data were collected through a structured self-administered questionnaire. The Statistical Package of Social Science (SPPS) version 25 was used with a minimum statistical significance α=0.05. The study population was nurses, nurse assistants, ward assistants and cleaners working at the study wards. Out of 191 questionnaires, 82 were received, with a response rate of 42.93%. Most participants were female (72%) and nurses (85,4%). Participants had medium to good knowledge about Infectious Medical Waste management and good knowledge regarding segregation practices applied in their ward. Segregation was not carried out as it should have since most participants stated that Infectious Medical Wastes were mixed with non-hazardous waste. Correct answers given by the participants regarding color-coding of different Healthcare Waste categories was 67.5%, and only four answered correctly to all questions. Although participants knew segregation practices and the colour-coding process applied for Healthcare Waste, they didn’t use them satisfactorily. They applied methods regarding segregation without specific training, knowledge and guidance. Due to the issue's importance, training programs must be implemented and performed.

The management and classification of solid waste is one of the most important challenges around the world, in order to sustain economic growth and preserve the environment. The objective is to propose the use of Smart Ecological Points as a strategy to address the problem related to the solid waste management system at the source, which has become one of the biggest problems globally and Colombia is no exception. The article describes the current state of the problem in the country and in turn, presents the possibility of developing a prototype corresponding to a low-cost Smart Ecological Point supported by the use of an experimental capacitive sensor and Machine Learning algorithms, which will reduce the time necessary for the classification of recyclable and non recyclable waste, minimizing the health risks and increasing the percentage of waste that can be reused, by reducing the probability of being contaminated at the source, an aspect that is very common when done manually. According to the results obtained, it was evident that the proposed prototype made an adequate classification of waste, generating the possibility of being manufactured with existing technology in the environment, in order to promote adequate waste classification at the source.

The article discusses an alternative way of recycling radioactive waste (RW), presented in the form of radioactive building materials - concrete and reinforced concrete structures and metal fittings, with the further use of materials, obtained during recycling, in the space industry. That is, it is supposed to send radioactive waste into space not as a passive ballast, but as a payload that will operate in space under conditions of increased radiation.

Insecticide testing facilities that evaluate a variety of vector control products may generate large amount of hazardous wastes from routine operations. These wastes originate from degraded technical grade materials, sprayed substrates, redundant stock or working insecticidal solutions. The washing of Long-Lasting Insecticidal Nets (LLINs) during preparation for laboratory and experimental hut trials also contribute to waste water with insecticide content. Human and environmental exposure to insecticidal waste can occur during transport, categorization, storage and disposal in resulting in environmental pollution and potential health effects. Various national and international guidelines have been devised for safe disposal and should be strictly followed to avoid adverse effects on humans or environment. The current paper describes a case study from insecticide test facility in north-eastern Tanzania in management of insecticidal waste.

Solid-state lighting has been replacing conventional lighting in the market, raising concerns for implementing an efficient end-of-life management system. Since LED waste streams have not been quite dominant, characterization studies (product-level characteristics, component-wise information, bill of materials, diversity, and differences) are inconsistent and having substantial gaps. This study investigates the end-of-life LED lamp literature, focusing on the bill-of-materials, and reveals that the characterization procedure suffers from a severe lack of sample representativeness. Consequently, characterization results are widely varied and not generalizable. Moreover, most of the studies did not inform and document the detailed sample characteristics, precluding the possibility of identifying reasons for variation. Combining available information from the recent studies, we present a mass distribution at the component level, exemplifying the prospect for meeting EU regulatory limit and the need for more insight at the lamp and component level. To fill the disconnection between lamp level characteristics and component and material content, we propose a characterization protocol that carefully documents lamp, component, and material level information by establishing a lamp-component–material composition nexus. The protocol may help researchers, policymakers, and industrial stakeholders conduct a systematic characterization, analyze complexities and prepare for a sustainable solution.

Lignocellulosic fungi are highly versatile organisms with valuable applications in bioremediation processes, including the biodegradation of agro-industrial effluents. In this work, the use of a native strain of the white-rot fungus, Pycnoporus aff. sanguineus, was studied for its use in the bioremediation of the sugar industry waste called vinasse, originating from the San Martín del Tabacal Sugar Mill, located in the north of the Salta province, Argentina. We studied under controlled laboratory conditions the bioremediation process of 3 concentrations of vinasse (5, 10, and 25% in distilled water) with a native isolated strain. The results showed biomass growth at all three tested concentrations, with a maximum at the highest vinasse concentration (25%), while the percentages of color and Chemical Oxygen Demand (COD) removal indicated that the most efficient treatment was with 10% vinasse. The results obtained are promising for the treatment of effluents from the sugar industry using white-rot fungi considering the valuable subproducts of Pycnoporus spp. biomass.

Bread is one of the most popular products consumed almost daily and, simultaneously, the most frequently wasted product in large quantities. The factors determining this phenomenon in a household must first be known in order to develop and implement effective programmes to combat consumers throwing away bread. Minimizing bread waste contributes to achieving the UN's Sustainable Development Goal 12 of "halting food waste by 2030". The aim of the study was to examine the influence of selected sociodemographic, economic and behavioural characteristics of consumers on the methods of managing stale bread. The study was conducted on a nationwide, random, and representative group of 1115 adult respondents. Over 15% of respondents admitted throwing stale bread into the waste container. Statistical analysis showed that the highest percentage of younger people, residents of large cities, and working people declared throwing unused bread into the waste container. More than 1/3 of respondents declared that they process stale bread into breadcrumbs. A higher percentage of the oldest people, residents of rural areas, and families with more than four adults declared that they manage bread this way. There was no significant relationship between the frequency of bread purchase and all methods of managing stale bread (except for feeding animals). The place of purchase influenced four methods of handling stale bread.

This report aims to document the extent of plastic waste pollution in lorry stations in Accra, assess its impact on public health and propose actionable solutions for effective waste management in stations. By highlighting the severity of the issue as well as providing recommendations for solutions, we seek to inform and inspire municipal assemblies, policymakers and other stakeholders to take decisive action against plastic waste pollution in lorry stations in Accra. Plastic waste pollution is a growing concern in Ghana, with lorry stations being particularly affected due to high foot traffic and inadequate waste management infrastructure within stations. This report is significant because of its implications for addressing public health hazards, continuing the ongoing efforts to reduce plastic pollution in Ghana and addressing community concerns. Through this comprehensive analysis, Mckingtorch Africa aims to drive meaningful change and create a cleaner, healthier Ghana for present and future generations.

Traditional lime-based materials have considerable potential for use as components of green materials for plastering and finishing building surfaces in both new construction and historic heritage conservation. The paper presents the preliminary results of a research activity aimed at developing pre-packaged products based on Traditional Lime Putty (TLP) by partially replacing natural aggregates with Stone Waste Sludge (SWS), with a low rate of recovery from Apricena limestone production district in Apulia. The mineralogical and chemical analysis carried out by means XRD (X-Ray Diffraction), TG-DTA (Thermo Gravimetry-Differential Thermal Analysis) and hydrochloric acid attack test showed that the SWS consisted of 98.4 % CaCO3 by mass. The particle sizes measured by laser diffraction technique are below 22.5 μm for the 92% by mass of the sample. The high fineness of the stone waste was confirmed by the Blaine specific surface method equal to 9273.79 cm2/gr. The behavior of three fresh mixtures for prepacked coarse plaster, fine plaster, and finishing plaster with 12.90%, 17.94%, and 18.90 by mass of SWS, respectively, was evaluated by spreading test and applicability tests on a perforated ceramic slab. The finishing plaster has the highest consistency value of 235 mm, while the fine plaster and the coarse plaster have values of 205 mm and 155 mm, respectively. The coarse plaster is suitable for the use as base plaster (arriccio) or second layer rendering (tonachino) up to a thickness of approximately 1 cm. Both the fine plaster and finishing plasters can be used for the surfaces finishing with the application of layers of a few millimeters thick.

Plastics, once regarded as a revolutionary material shaping modern society, now poses an unprecedented threat to our environment. Household solid waste sorting stations produce several fractions, one of which contains a high concentration of Low-Density Polyethylene (LDPE) film waste (packaging, sunscreen film, etc.). This fraction is difficult to recycle because it contains quite a lot of impurities. Usually, it is sent to the cement factories that burn it together with other fuels. However, with some processing techniques such catalytic pyrolysis this fraction could be valorized. In this paper the experiments which were carried out at a laboratory scale installation, in batches with a processing capacity of 1-3 kg of waste. The pyrolysis reactor is connected to a distillation column giving the possibility to separate the fractions. The gaseous and liquid fractions were characterized by GC-FID-TCD (gases) and GC-MS (liquids) analysis. Natural catalysts such as bentonite or clinoptilolite were studied and used in the melting of plastic mass to simplify the process as much as possible. To test the activity of the catalysts, the pyrolysis of LDPE granules was initially studied. It was found that natural zeolites are much more active than bentonite and that a minimum concentration of 5-10% is needed to have a positive effect on the composition of the fractions (increasing the weight of the light fractions C1-C6, C6-C10 and C11-C13) in relation to the heavy fractions C13-C20 and C20+. Catalytic pyrolysis gives a completely different distribution of light hydrocarbons. The best catalyst selected from LDPE lab experiments, was then tested upon the pyrolysis of plastic film waste obtained by a waste treatment plant. The research objective reported in this paper was to obtain a fraction of combustible gases in the largest possible proportion, which can be much easier exploited by burning in an engine that drives an electric generator.

This research seeks to solve the multi-faceted problem of waste disposal by analyzing the application of waste plastic and tyre material within non-structural concrete to ensure more sustainability and less environmental degradation. Study focusses on material properties including specific gravity, water absorption and bulk density and characteristics of the concrete that is produced by the utilization of the above waste aggregates including workability, compressive strength, flexural strength and tensile strength. This paper employs secondary data collection and MATLAB in the analysis of the findings pointing to the fact that the mechanical properties reduce with the level of waste content yet emphasizing the green aspect of such materials. Thus, a complex and diverse effect is demonstrated by the life cycle assessments (LCA) for global warming, ozone depletion, terrestrial ecotoxicity, and acidification. Furthermore, the utilization of waste materials decreases the compressive, flexural, and tensile strength, but it provides distinct ecological benefits which prove the importance of proper mix proportions for concrete performance. The outcomes of this research will be useful for further investigation in the application of the concept as well as to call for the development of new ideas for the improvement of bonding of wastes to aggregates in concrete.

The paper presents a thorough examination of the burgeoning field of utilizing manufacturing waste for sustainable energy generation, aligning with the global imperative for resource efficiency and clean energy solutions. With the manufacturing sector being a significant contributor to waste generation, this study explores innovative approaches to transform waste materials into valuable resources, thereby mitigating environmental impacts and contributing to a circular economy. This work critically reviews current trends, emphasizing technological advancements, policy interventions, and market dynamics shaping the manufacturing waste utilization landscape. Noteworthy developments, such as advanced sorting technologies and the integration of digital solutions, are discussed in detail, showcasing their role in enhancing the efficiency of waste management processes. The study outlines future trends in the field, anticipating a shift towards closed-loop systems guided by circular economy principles. This comprehensive review aims to contribute to the discourse on sustainable waste management and energy generation by providing a holistic perspective on the field's current state and offering insights into the future trajectories that will propel manufacturing waste toward a more sustainable and circular future. The synthesis of technological innovation, collaborative efforts, and evolving regulatory frameworks presents a compelling case for the continued exploration of manufacturing waste as a valuable resource in the pursuit of a more sustainable and energy-efficient world.

In South Korea, demolition waste (DW) management has become increasingly significant owing to the rising number of old buildings. Effective DW management requires an efficient approach that accurately quantifies and predicts the generation of DW (DWG) of various types, which necessitates access to the required information or technology capable of achieving this. Hence, we developed an artificial intelligence-based model that predicts the generation of ten DW types, specifically from buildings in redevelopment areas. We used an artificial neural network algorithm with < 10 neurons in the hidden layer to derive individual input variables and optimal hyperparameters for each DW type. All DWG prediction models achieved an average validation and test prediction performance (R²) of 0.970 and 0.952, respectively, with their ratios of percent deviation ≥ 2.5, ver-ifying them as excellent models. Moreover, a Shapley additive explanations analysis revealed that DWG was most impacted by the floor area for all the DW types, with a positive correlation with DWG. Conversely, other factors showed either a positive or negative correlation with DWG de-pending on the DW type. The study findings will enable demolition companies and local gov-ernments in making informed decisions for efficient DW management and resource allocation by accurately predicting the generation of various types of DW.

The recycling, incineration, and final disposal rate of municipal solid waste (MSW) are calculated based on the total amount of waste input to each facility in many countries. These statistic data have serious limitation in setting the national goal and policy for effective waste management because it is not considering the amount of foreign objectives in the process of each life-cycle stage. This case study is to estimate the actual rates of recycling, incineration, and final disposal by material flow analysis (MFA) after the collection of MSW in Korea. The actual rates of recycling, incineration and final disposal for MSW in 2016 were 49.9%, 32.9% and 23.1% respectively, indicating that the recycling rate was lower by 10.1%, while the incineration and final disposal rates were raised by 7.6% and 8.4% respectively, compared with the statistics for current MSW. In addition, the changed actual rates of recycling, incineration treatment, and final landfill, and variation of waste treatment charge according to treated amounts per treatment method was analyzed. This results of this study will contribute to establish national level of plan on effective waste management.

SDG target 12.3 calls for halving food waste at retail, food service, and household by 2030. The food waste index for this purpose includes parts attached to food that are usually removed intentionally ("unavoidable food waste") and allows counting the conversion to animal feed and utilisation as biomaterial as means of reduction. In Japan, the "Food Waste Recycling Law" which has been in effect since 2001, promotes the recycling of food waste generated from businesses, designating feed conversion as top priority. On the other hand, based on the more recent "Food Loss Reduction Promotion Act" of 2019, the government is currently promoting the reduction of avoidable food waste, as to meet the SDG target. Based on statistical sources and interviews with Ministry officers, this paper explains the history and achievements of Japan's 23-year policy based on the Food Recycling Law, as well as the tension between the two legislations.

Spent nuclear fuel and high-level radioactive waste can be disposed in deep horizontal drillholes in sedimentary, metamorphic, or igneous rocks. Horizontal drillhole disposal has safety, operational, and economic benefits: The repository is deep in the brine-saturated zone far below aquifers in a reducing environment of formations that can be shown to have been isolated from the surface for millions of years; its depth provides safety against inadvertent intrusion, earth¬quakes, and near-surface perturbations; it can be placed close to the reactors and interim storage facilities, minimizing transportation; disposal costs per ton of waste can be kept substantially lower than for mined repositories by its smaller size, reduced infrastructure needs, and staged imple¬mentation; and, if desired, the waste could be retrieved using “fishing” technology. In the proposed disposal concept, corrosion-resistant canisters containing unmodified fuel assemblies from commercial reactors would be placed end-to-end in up to 50 cm diameter horizontal drill¬holes, a configuration that reduces mechanical stresses and keeps the temperatures below the boiling point of the brine. Other high-level wastes, such as capsules containing 137Cs and 90Sr, can be disposed in small-diameter drillholes. We provide an overview of this novel disposal concept and its technology, discuss some of its safety aspects, and compare it to mined repositories and the deep vertical borehole disposal concept.

The increasing focus on environmental sustainability has prompted the healthcare sector, including dentistry, to reconsider waste management practices. Dental offices generate various waste streams from outdated technologies, including single-use plastics, hazardous materials, and digital waste. This scoping review explores how integrating circular economy principles with lean management practices can enhance sustainability and operational efficiency in dental clinics. Using the PRISMA methodology, the review identifies 30 articles that passed 1) the Cochrane Risk of Bias Tool and b) the Critical Appraisal Skills Programme (CASP) checklist from 2000. Circular economy principles focus on reducing waste and maximizing resource reuse, while lean management seeks to improve efficiency and minimize process waste. Together, these approaches can significantly reduce resource consumption and enhance recycling efforts in dental practices. However, barriers include high costs of sustainable technologies, regulatory challenges, and limited recycling infrastructure. The study also highlights case studies of healthcare and dental clinics successfully implementing these strategies, showing how they can overcome challenges and improve environmental and operational outcomes. Collaboration between dental professionals, policymakers, and industry leaders is essential for promoting the adoption of these sustainable practices.

The organic fraction of municipal solid waste (OFMSW) is a significant environmental threat, and an economic and social challenge to manage. As such, the efficient treatment of OFMSW is a significant key factor in achieving sustainable waste management. Decentralized Composting (DC) develops a new framework of waste management. The DC Analysis Model (DCAM), proposed in our previous study, provides a powerful tool for decision makers, based on the quantification of the DC project characteristics. In this paper, we focus on the qualitative analysis as a complementary tool to support decision making, in cases where quantitative analysis is unequivocal. The qualitative analysis identifies the main players in the field, the critical stakeholders and the potential conflicts between them. It also reveals the root problems and the core competencies for the project's implementation. DCAM qualitative analysis in Shefa-Amr (case study) indicates that unresolved root problems, such as the “lack of national regulation”, “clear ownership of the project” and “lack of ongoing budget” can result in an unsustainable composting system. Countering that, “the commitment of the municipality”, together with “economic viability” and securing “suitable areas for placing composters” are among the most important core competencies for the effective implementation of DC projects.

Millions of tons of wool waste are produced yearly by textile industries, which may become a serious environmental hazard in the near future. Given this concern, it is crucial to explore strategies to reduce the amount of wool waste generated worldwide and adopt more sustainable practices for dissolving and regenerating wool keratin (WK) from textile waste. Most traditional methods involve the use of expensive, toxic, harmful, and poorly biodegradable compounds. To overcome these limitations and facilitate the reuse of wool waste through a cascade valorization strategy, researchers have started testing the use of deep eutectic solvents (DES) as a more sus-tainable and eco-friendlier alternative for WK dissolution and regeneration. In this study, the potential of two different DES mixtures, Choline chloride (ChCl): Urea and L-Cysteine (L-Cys): Lactic acid (LA), was explored for dissolving wool waste. Subsequently, the obtained gels based on DES-WK were blended with polyvinyl alcohol (PVA) in different ratios to produce nanofibers using the electrospinning technique. The effect of pH and the properties of the electrospinning solutions, namely electrical conductivity and viscosity, on the morphology of the gel solutions were evaluated. Moreover, the morphological features of the produced gel-based electrospun PVA/DES-WK nanofibrous membranes were analyzed using scanning electron mi-croscopy (SEM). Additionally, the PVA/L-Cys: LA DES-WK, which proved to be the most effective DES mixture for fabricating WK gel-based nanofibers, were characterized through Fourier transform infrared spectroscopy (FTIR) and tensile tests. Furthermore, their antioxidant and an-timicrobial abilities were evaluated. The results obtained revealed that this approach to valorize textile waste offers a unique avenue for the development of sustainable functional materials with potential applications in various biomedical and industrial fields.

Sharing the same raw material, recycling and composting are in direct conflict with incineration of municipal solid waste in combined heath and power plants. Indeed, waste-to-energy plants in regions with high recycling rates import urban waste from other countries to use otherwise unused capacity, and raise revenues. Using the case of Italy’s second largest and economically most developed region, I discuss the economic viability of municipal solid waste incineration to produce electricity and heath in the context of the increasing role of electricity production from renewable energy sources as well as of the emerging mass-scale uptake of bioplastics. Four lessons and three guidelines aimed to local authorities and policy makers emerge from the present study.

Lean is one of the systematic approach to achieve higher value for organizations through eliminate non-value-added activities. It is an integrated set of tools, techniques, and principles designed to optimize cost, quality and delivery while improving safety. In Vietnam, industry waste management and treatment has become serious issue. The aim of this research is to present the effective of Lean application for industrial wastes collecting and delivery improvement. Through a case study, this paper showed the way of Lean tools and principles applied for wastes management and treatment such as Value Stream Mapping, Pull system, Visual Control, and Andon.... to get benefit on both economic and environment. In addition, the results introduced a good experience for Vietnamese enterprises in cost saving and sustainable development in waste management.

Continuity of activities and projects are important for sustainably developing organizations, especially universities. The purpose of this research study is to find university development guidelines regarding waste management according to the green university ranking criteria for sustainable developments by studying and collecting the data covering the last five years (2019 - 2023) of Mahasarakham University. We also analyzed and synthesized lessons learned from the details of the operations and the factors involved in successes while comparing and providing suggestions for the operations in the next year. It was found that waste management that resulted in continuous developments that achieved the goals of Mahasarakham University consisted of the five guidelines. (1) Making green university policies and using them as the (key performance index) KPI of the divisions and also announcing the university's waste management policies by applying the principles of 3R (Reuse-Reduce-Recycle). (2) Allocating the budgets supporting the projects' activities according to the evaluation criteria. (3) Student and personnel participation as well as the mechanisms used by the committees from various administrative divisions such as Student Council, Student Association and clubs to drive the operations. (4) Identifying the main responsible individuals and committees for the green university who communicated and drove the operations while collecting, analyzing and preparing the data. (5) Follow-ups and evaluations of the project's activities with the Plan-Do-Check-Act (PDCA) processes for continuous and sustainable developments and improvements leading to the green university. With the above operations, Mahasarakham University's waste management scores of the six indices during 2019 - 3023 increased annually as follows: 900, 900, 1050, 1275 and 1350.